Samsung SCP-2371 User manual

SPEED DOME CAMERA
User Manual
SCP-3371/SCP-3371H
SCP-2371/SCP-2371H
SCP-2271/SCP-2271H
SPEED DOME CAMERA
User Manual
Copyright
©2013 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document
shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but
no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the
user’s own responsibility. Samsung Techwin shall have the right to change the contents of this manual without
prior notice for the purpose of enhanced performance.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve
the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
• If the system behaves abnormally because you run a program irrelevant to the system operation.
• Deteriorated performance or natural worn-out in process of time
™Design and specifications are subject to change without prior notice.
safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that there are important operating and maintenance instructions in the
literature accompanying this unit.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
- Do NOT use power sources other than Class 2 power source.
- REPLACE WITH SAME TYPE 250V T3.15AL FUSE(F1)
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or
damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat
generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water
on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately
disconnect the power source and contact the service center. Continued use in such a condition may cause
fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product
in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
CAUTION - Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to
excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 55°C), low temperature (below -50°C), or high
humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fire
or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
English - 3
● SAFETY INFORMATION
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within
this unit.
safety information
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the
CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
9. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CCD.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may cause undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian Interference.-Causing
Equipment Regulations of ICES-003.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of
their working life. To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate these items from other types of waste and recycle them responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human
health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of
waste and recycle them through your local, free battery return system.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
4_ safety information
important safety instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including
amplifiers) that produce heat.
8. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such
as vases, shall be placed on the apparatus
WARNING
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the
installation instructions.
English - 5
● IMPORTANT SAFETY INSTRUCTIONS
5. Clean only with dry cloth.
CAUTION
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric
shock, do not perform any servicing other than that contained in the operating instructions unless you are
qualified to do so.
DETAILED WARNINGS AND CAUTIONS
y Avoid operating the camera for long durations under high temperatures and in high humidity. Excessive
heat can shorten the lifespan of the camera components.
y Do not install or place the camera near any heat sources.
y Subjecting the dome cover to physical shock may damage the camera and cause water leakage into it.
y Do not place the camera facing direct sunlight or other intense light sources. Strong lights such as
spotlights can cause distortions—blooming and smear—as well as discolorations on the screen by
heating up the color filter of the camera. They also may cause internal reflections of the camera, leading
to operational malfunctions.
y Do not drop the camera or subject it to physical shock or vibration; this can cause serious damage to the
camera.
y When installing the camera near a power line, make sure to keep at least 1 meter distance from the
power line, or earth an additional metal pipe to separate the camera from the power source.
y Install this camera on the ceiling. Installing it on the ground or a unleveled location may cause product
malfunctions and shorten its lifespan.
y Avoid installing and operating the camera in the following places.
- Places whose temperature exceed the camera’s recommended range.
(Indoor : -10º ~ 55º, Environmental : -50º ~ 55º)
- Places where drastic temperature changes occur: e.g. Near an air conditioner.
- Places that are exposed to steam, oil, and inflammable substances: e.g. Inside a kitchen.
- Places that are exposed to radioactivity, X-rays, strong electric waves, and electro-magnetic waves.
- Places that are exposed to outdoor air contaminants: e.g. Dust and car exhaust.
- Places in high humidity.
- Places that are exposed to corrosive gas: e.g. Next to the sea.
y Smeared and dusty dome covers decrease the picture and video quality. Clean the dome cover and
camera lens on a regular basis.
y Remove the plastic wrap on the dome cover only after the camera installation is complete.
y This camera is not equipped with a power switch. Plug in the camera only after the installation is
complete.
6_ important safety instructions
CAUTIONS FOR OPERATING TEMPERATURE (FOR ENVIRONMENTAL MODELS)
1. The camera cannot operate properly at temperatures lower than -50°.
2. If the product is kept at a low temperature, it may take a max of 2 hours to warm up for normal
operation.
- If the internal temperature is lower than -20°, the camera does not transmit video signals and
displays a black screen along with the "Wait to warm up(xx Left)" message, instead of operating
properly.
- If the internal temperature is higher than -20° and lower than -10°, the "Wait to warm up(xx Left)"
message disappears as the camera resets itself and enters the operation mode.
However, only manual P/T operation is in effect while the Sequence and Turbo commands are
limited in use.
- If the internal temperature is higher than -10°, the camera activates all Sequence and Turbo
commands.
4. The speed of the horizontal/vertical rotation will be deteriorated than normal at below -10 degrees for
the indoor model, and at below -40 degrees for the environmental model.
5. If the heater malfunctions, a message appears as follows.
- "Please Check Heater System"
- If this message appears, turn off the camera and call where you bought.
Samsung Techwin cares for the environment at all product manufacturing stages to
preserve the environment, and is taking a number of steps to provide customers with
more environment-friendly products.The Eco mark represents Samsung Techwin’s
will to create environment-friendly products, and indicates that the product satisfies
the EU RoHS Directive.
English - 7
● IMPORTANT SAFETY INSTRUCTIONS
3. If the camera was turned on after being left at temperatures lower than -50° for a long duration:
contents
INTRODUCTION
9
CONNECTION &
INSTALLATION
14
SETUP
42
TROUBLESHOOTING
9
11
12
13
Features
What’s included
Component Names and Functions (Indoor Model)
Component Names and Functions
(Environmental Model)
14
15
17
18
21
29
30
31
32
35
38
Camera Wiring Interface Board
Camera and Appliances Wiring Diagram
How to Set Up Protocols and ID DIP Switches
Communication Protocol DIP Switch
Settings (SW2)
Camera ID DIP Switch Settings (SW1)
Preparing Adapter and Cables
Product Configurations
Preparing & Installing Camera Bracket
Optional Accessories for Installation
On-Ceiling Mount Type Installation Example
Example of installing an Environmental model
42
43
44
45
55
67
75
76
79
80
80
Interface Symbols
Using and setting the menus
OSD Menu Chart
Camera Setup
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password setting
Status
81 Troubleshooting
81
PRODUCT SPECIFICATIONS
85
8_ contents
85 Product Specifications (SCP-2XX1 Series)
87 Product Specifications (SCP-3371 Series)
89 Dimensions
introduction
FEATURES
y A/F 37x/27x Optical Zoom
The built-in 37x / 27x optical zoom lens with auto-focus is combined with a 16x digital zoom,
providing a maximum of 592/432 zoom.
- RS-422/485 (10 species) : Auto Detected, SAMSUNG-T, SAMSUNG-E, Pelco (D/P), Panasonic, Vicon,
Honeywell, AD, GE, BOSCH
- Coaxial Communications : Pelco Coaxitron (Camera ID DIP switches (SW1) are all positioned to OFF)
y Wide Range Auto Security Functions
- Multiple Preset Function Saving : Up to 12 camera image properities can be saved individually to provide
high quality pictures.
- Image Holding : When moving in a group tour, the screen appears in a still image until the movement is
complete, thus reducing the optical fatigue of the observer.
- PTZ Trace : Patterns operated with the joystick can be saved and replayed by users.
- Swing : Using the Swing function commands the camera to move between 2 selected locations, monitoring
the route.
- Group Search : Maximum 128 Preset positions are toured in order.
- Tour Search : Maximum 6 Group Search functions are toured in order.
y Digital Flip
The Digital Flip function is useful to monitor moving objects or people passing directly under the
camera. When an object or a person passes directly under the camera, its tilt motor follows the
object or person over 90 degrees to the other side of the tilt area without panning. The screen
inversion starts to occur at 90 degrees or higher is digitally adjusted.
y Smart P/T
The Smart P/T function automatically adjusts the control speed of the Pan and Tilt functions
according to the current zoom ratio. It is useful to adjust the functions manually for detailed controls
when monitoring at high zoom ratios.
y Day & Night
With its daytime & nighttime switch and Sens-Up functions based on the ICR (Infrared Cut filter
Removal) method, the camera provides high quality pictures regardless of whether it is day or night.
- Sens-Up increases the CCD sensitivity by electrically extending the camera’s exposure time.
- Day & Night enables you to select between color and B/W modes depending on the lighting conditions.
y Highly durable built-in housing
This IP66-rated built-in housing is easy to install, and protects the product from a full range of harsh
outside conditions. The high performance built-in fan/heater enables the product to operate under
extreme temperatures between -50° ~ 55° .
English - 9
● INTRODUCTION
y Versatile protocols and coaxial communication
RS-422/485, Coaxial communication methods are supported.
introduction
y Preset Position Saving and Loading
Up to 255 preset positions can be set. Using this function saves and brings up the camera feed of
a selected monitoring location.
y Camera Backup
This is to back up the camera’s sequence information and presets. This is useful when the camera
or its install base are damaged or malfunctions occur.
y Area Masking
If a monitoring location includes a highly private area, the area can be selectively masked on the
screen.
y Model Specifications
SCP-XXX1H
Environmental Model
Zoom Factor
37: 37 Zoom Lens / 27: 27 Zoom Lens
DSP Chip
2: W-V DSP/3:SV-V DSP
10_ introduction
WHAT’S INCLUDED
Check if the following items are included in the product package.
Appearance
Item Name
Description
Applicable
Model
1
-
Indoor Model
1
-
Environmental
Model
1
Multilingual User Manual
Main Body
CD Manual (Optional)
All
User Manual
1
English User Manual
Fixing Screw
4
If mounting the install base on the
ceiling
Installation Template
1
If determining the installation
point before mounting the install
base on the ceiling
Insulation Sheet
1
In the case of installing the
camera at highly humid place
Hexagon screw
3
Used for attaching the installation
base to the camera
Indoor Model
Environmental
Model
L Wrench
1
Used for fixing the installation
base after attaching it to the
camera
Ú For classification of the indoor and environmental models, refer to page 10.
English - 11
● INTRODUCTION
Quantity
introduction
COMPONENT NAMES AND FUNCTIONS (INDOOR MODEL)
Front
Back
➊
Install base
❶ Unlock Button
➋
➋ SW1: ID DIP Switch
0/
➌ SW2: Communication DIP Switch
Ú For the DIP switch settings, please refer to the
“Installing Your Camera” on Page 17~21.
0/
➌
12_ introduction
COMPONENT NAMES AND FUNCTIONS(ENVIRONMENTAL MODEL)
Front
Back
Install base
➋
➌
➊ Safety Wire Holder
➋ SW2: Communication DIP Switch
➌ SW1: ID DIP Switch
Ú For the DIP switch settings, please refer to the
“Installing Your Camera” on Page 17~21.
English - 13
● INTRODUCTION
➊
connection & installation
CAMERA WIRING INTERFACE BOARD
For the camera wiring, please refer to the picture below.
(When using coaxial communication, a separate control signal connection is not required.)
Alarm/AUX
2.NC
Alarm/
AUX Output 2
2.NO
2.COM
IN8
Alarm
Input
5~8
Alarm/
AUX Output 1
IN7
GND
IN6
IN4
IN5
Alarm Input
1~4
Communications and Alarm/AUX
RX
3.COM 3.NO
RX
Power Supply
FG
Refer to the below Control
Signal Connection chart
AC24V 2.5A
Alarm/
AUX
Output 3
Power Input
Ground
Ú After connecting the power cable by
separating the power connector from the
terminal, make the connection between
terminal and connector by using a bolt.
Control Signal Connection
• RS485 Communications
Camera
RX+
RX-
Controller
or DVR
TXD+
TXD-
• RS422 Communications
Camera
RX+
RXTX+
TX-
Controller
or DVR
TXD+
TXDRXD+
RXD-
M  The max capacity of the Alarm OUT/AUX OUT ports are 30VDC/2A, 125VAC/0.5A, and 250VAC/0.25A, respectively.
 Connecting the power connector and GND incorrectly to the NC/NO and COM ports may cause a short circuit and fire,
damaging the camera.
14_ connection & installation
CAMERA AND APPLIANCES WIRING DIAGRAM
Connecting with Samsung Techwin’s “Stand Alone DVR”
Camera
RX+
RX-
● CONNECTION & INSTALLATION
y RS-485 :
Stand Alone DVR
T(TXD)+
T(TXD)-
y RS-422 :
Camera
Stand Alone DVR
RX+
RX-
T(TXD)+
T(TXD)-
TX+
TX-
R(RXD)+
R(TXD)-
Connecting with the Samsung Techwin Controller SPC-6000
y RS-485 :
Camera
RX+
RX-
TXD+
TXD-
TX
RX
+ -
TX
G
+ -
+ -
RX
+
-
y RS-422 :
TX
+ -
Camera
RX
+ -
G
TX
+ -
RX
+
-
MENU
SEARC
H
MULTI
REC
1
TX+
TX-
RXD+
RXD-
RX+
RX-
TXD+
TXD-
6
MON
2
7
MENU
PRESE
T
CAM
GROUP
PTZ
3
8
DVR
4
9
MTX
5
SETUP
ESC
TRACK
FUNC
ENTER
CLOSE
OPEN
0
NEAR
WIDE
FAR
TELE
<Controller>
English - 15
connection & installation
To connect to Samsung PC DVR
y RS-485 :
Camera
RX+
RX-
16_ connection & installation
PC DVR
HOW TO SET UP PROTOCOLS AND ID DIP SWITCHES
You can control various settings of the camera system using the Communication and ID DIP switches.
Before installing the product, please set up the DIP switches according to the installation environment.
Communication Protocol
DIP Switch(SW2)
Camera ID DIP Switch(SW1)
English - 17
● CONNECTION & INSTALLATION
1. Remove the install base from the camera body and place the part to be headed to the lower end as
shown in the figure.
2. Set the switches according to your installation environment. For more detailed setup information, please refer
to the chart on the next page.
3. The camera may malfunction if the switches are not fully turned On/Off; please double check the switches
before finishing setup.
connection & installation
COMMUNICATION PROTOCOL DIP SWITCH SETTINGS (SW2)
ON
ON
OFF
SW2
SW2 Pin No.
Purpose
1~4
Protocol Settings
5~6
Baud Rate Settings
7
Transfer Method (RS-485/422) Settings
8
Response Mode Settings
9~10
Backup Mode Settings
11~12
Termination Settings
Protocol Settings
Select a communication protocol for the camera.
No
Protocol
SW2-#1
SW2-#2
SW2-#3
SW2-#4
1
Auto Detected
OFF
OFF
OFF
OFF
2
Samsung-T
OFF
OFF
OFF
ON
3
Samsung-E
OFF
OFF
ON
OFF
4
Pelco-D
OFF
OFF
ON
ON
5
Pelco-P
OFF
ON
OFF
OFF
6
Panasonic
OFF
ON
OFF
ON
7
Vicon
OFF
ON
ON
OFF
8
Honeywell
OFF
ON
ON
ON
9
AD
ON
OFF
OFF
OFF
10
GE
ON
OFF
OFF
ON
11
Bosch
ON
OFF
ON
OFF
18_ connection & installation
Baud Rate Settings
Select the transfer speed of a selected communication protocol.
Baud Rate (BPS)
SW2-#5
SW2-#6
1
2,400
ON
ON
2
4,800
ON
OFF
3
9,600
OFF
OFF
4
19,200
OFF
ON
Communication Method Settings
Select a communication method for the camera.
SW2- #7
Function
Transfer Mode Switch
ON
RS-422 (4Wire)
OFF
RS-485 (2Wire)
Communication Response Settings
Select a communication response method for the camera and controller: Response or No Response.
SW2- #8
Function
ON
OFF
Response Mode Switch
Response
No Response
Termination Settings
To prevent the attenuation of communication signals between the camera and controller, the items at
the end of line must be set up with the termination settings.
Camera Input Position
SW2- #11
SW2- #12
Termination of Longest Path (RS-422)
ON
ON
Termination of Longest Path (RS-485)
ON
OFF
On the Path
OFF
OFF
y Example of terminal setting
Ú If using RS-422, SW2-#11: ON /SW2-#12: ON for camera 16
Ú If using RS-485, SW2-#11: ON / SW2-#12: OFF for camera 16
English - 19
● CONNECTION & INSTALLATION
No
connection & installation
Camera Backup Settings
These settings are useful when the camera or its install base are damaged or malfunctions occur.
When replacing the camera or its install base, you can transfer existing presets and sequence
information to the replacement using these settings.
Backup Function
SW2- #9
SW2- #10
Backup(IBˆD)
OFF
OFF
Backup(DˆIB)
ON
OFF
Backup Disable
-
ON
- Backup(IBˆD) : Enables transferring the current camera's sequence information to a new camera.
- Backup(DˆIB) : Enables transferring the current camera's sequence information to a new install base.
Ú IB: Install base, D: Dome Camera
■ [Current Time] is not backed up from install base to camera.
model is shipped from the factory with all the communication dip switches (SW2) set to OFF, and the default values
I  This
are shaded as shown in the setting table.
 If you want to use a third-party controller for controlling the camera, contact us at the call center or visit our website for
details.
 AD Protocol Control Method
1. Input Camera OSD: 3+Auxiliary On
2. Output Camera OSD: 3+Auxiliary Off
3. Enter: IRIS Open
4. ESC: IRIS Close
 For more information about the protocols, refer to our official website.
http://www.samsungtechwin.com/
20_ connection & installation
CAMERA ID DIP SWITCH SETTINGS (SW1)
Assign a unique number for each camera to identify itself from others.
ON
ON
● CONNECTION & INSTALLATION
OFF
SW1
1. The switch is set to “ID: 1” by default, and 7 switches other than
switch 1 are all set to OFF.
ON
OFF
2. Each switch has a unique value, and the board ID is the sum of
the values of the switches.
 Refer to the example below for the board ID.
Example 1
Example 2
1+2 = 3 (Board ID = 3)
Example 3
4+32 = 36 (Board ID = 36)
1+2+4+8+16+32+64+128
= 255 (Board ID = 255 )
M  Use a unique ID for each Camera.
 In coaxial communication systems, the camera will work normally only if the Camera ID DIP switches (SW1) are all
positioned to OFF.
English - 21
connection & installation
y Camera ID Chart
ID
COAX
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
SW1-#1
SW1-#2
SW1-#3
SW1-#4
SW1-#5
SW1-#6
SW1-#7
SW1-#8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
22_ connection & installation
SW1-#1
SW1-#2
SW1-#3
SW1-#4
SW1-#5
SW1-#6
SW1-#7
SW1-#8
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
English - 23
● CONNECTION & INSTALLATION
ID
connection & installation
ID
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
SW1-#1
SW1-#2
SW1-#3
SW1-#4
SW1-#5
SW1-#6
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
24_ connection & installation
SW1-#7
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ID
SW1-#2
SW1-#3
SW1-#4
SW1-#5
SW1-#6
SW1-#7
SW1-#8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
English - 25
● CONNECTION & INSTALLATION
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
SW1-#1
connection & installation
ID
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
SW1-#1
SW1-#2
SW1-#3
SW1-#4
SW1-#5
SW1-#6
SW1-#7
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
26_ connection & installation
SW1-#8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ID
SW1-#2
SW1-#3
SW1-#4
SW1-#5
SW1-#6
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#7
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
English - 27
● CONNECTION & INSTALLATION
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
SW1-#1
connection & installation
ID
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
SW1-#1
SW1-#2
SW1-#3
SW1-#4
SW1-#5
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
28_ connection & installation
SW1-#6
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#7
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1-#8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
PREPARING ADAPTER AND CABLES
y Power Adapter
Power adapter has the capacity of AC24V 2.5A.
connecting the power cable by separating the power connector from the terminal, make the connection between
M  After
terminal and connector by using a bolt.
y Video Cable
The camera’s video output port is connected to the monitor with a BNC coaxial cable, shown below :
If the distance between the camera and the monitor exceeds the recommended maximum, please use
an auxiliary video amp.
Distance
Recommended Cable
Specification
300m
4C2V(RG-59/U)
450m
5C2V(RG-6/U)
600m
7C2V(RG-11/U)
the camera is controlled through coaxial communication, please use a video amp intended for coaxial communications.
M  IfRegular
video amps do not transfer coaxial signals.
y Communications Cable
For the camera to communicate with the controller, a
RS-485/422 communications line is required. To ensure the
quality of long distance communication and the accuracy of the
overall communication it is recommended using a twisted pair
cable such as UTP.
M  Depending on the camera’s environment, the communications distance may vary.
 Neither the video nor communications cable is enclosed with the camera.
English - 29
● CONNECTION & INSTALLATION
<Camera Wiring Interface Board>
connection & installation
PRODUCT CONFIGURATIONS
ALARM
HDD
NETWORK
BACKUP
REC
REC
1
DVD RECORDER
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ZOOM
FR
P S
TELE
WIDE
MODE
AUDI
VIEW
USB
OPEN/CLOSE
RETURN
RS-485
SRD Series
ALARM
HDD
NETWORK
BACKUP
REC
REC
1
DVD RECORDER
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ZOOM
FREEZE BACKUP SEARCH
TELE
WIDE
MODE
AUDIO
VIE
ALRAM
MENU
USB
OPEN/CLOSE
RETURN
RS-485
SRD Series
ALARM
HDD
NETWORK
BACKUP
REC
REC
1
DVD RECORDER
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ZOOM
FR
P S
TELE
WIDE
MODE
AUDI
VIEW
USB
OPEN/CLOSE
R
Coaxial Communication
SRD Series
ALARM
HDD
NETWORK
BACKUP
REC
REC
1
DVD RECORDER
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ZOOM
FR
P S
TELE
WIDE
MODE
AUDI
VIEW
USB
OPEN/CLOSE
R
Coaxial Communication
SRD Series
CONTROLLER (SUB)
CONTROLLER (MAIN)
MENU
SEARC
MENU
SEARC
H
MULTI
MULTI
REC
MON
2
7
REC
MENU
PRESE
T
CAM
1
6
DVR
4
9
MTX
5
SETUP
ESC
1
TRACK
6
FUNC
ENTER
CLOSE
OPEN
0
NEAR
WIDE
30_ connection & installation
MON
2
7
MENU
PRESE
T
CAM
GROUP
PTZ
3
8
H
GROUP
PTZ
3
8
DVR
4
9
MTX
5
SETUP
ESC
TRACK
FUNC
ENTER
NEAR
FAR
TELE
CLOSE
OPEN
0
WIDE
FAR
TELE
CONTROL LINE
VIDEO LINE
CONTROL/VIDEO LINE
PREPARING & INSTALLING CAMERA BRACKET
For installation guidelines for brackets and housings, refer to the installation manual that is enclosed with the
bracket or housing.
❖ Available Bracket Models
Item
SHP-3701H
Outdoor Housing
SHP-3701F
In-ceiling Housing
SBP-300HM3
Hanging Mount
Indoor Model
Environmental Model
-
SBP-300WM1
Wall Mount
Yes
SBP-300WM
SBP-300CM
Ceiling Mount
SBP-300LM
Parapet Mount
SBP-300KM
Corner Mount
SBP-300PM
Pole Mount
Yes
M  See “Optional Accessories for Installation” for the appearance of each bracket
English - 31
● CONNECTION & INSTALLATION
Model
connection & installation
OPTIONAL ACCESSORIES FOR INSTALLATION
For your easier installation, you can purchase appropriate optional accessories available.
1. If installing the camera on the wall
y Wall mount (SBP-300WM1)
y Wall mount (SBP-300WM)
2. If installing the camera on the ceiling
y Ceiling Mount (SBP-300CM)
3. If installing the wall mount (SBP-300WM/SBP-300WM1) on an at least
80mm-long cylinder
y Pole Mount (SBP-300PM)
32_ connection & installation
4. If installing the wall mount (SBP-300WM/SBP-300WM1) on a corner of the wall
y Corner Mount (SBP-300KM)
● CONNECTION & INSTALLATION
5. If installing on a building rooftop
y Parapet Mount (SBP-300LM)
6. If installing an indoor model outdoors
y Outdoor Housing (SHP-3701H)
7. If installing an indoor model on the ceiling
y Flush-Mount Indoor Housing for PTZ Dome Camera
(SHP-3701F)
8. If installing an indoor model on the wall mount or ceiling mount
y Hanging Mount (SBP-300HM3)
English - 33
connection & installation
y Bracket Mounting (Indoor Model)
Wall mount (SBP-300WM1, SBP-300HM3)
Ceiling Mount (SBP-300CM, SBP-300HM3)
Wall mount (SBP-300WM, SBP-300HM3)
Parapet Mount (SBP-300LM, SBP-300HM3)
y Bracket Mounting (Environmental Model)
Wall mount (SBP-300WM1)
Ceiling Mount (SBP-300CM)
34_ connection & installation
Wall mount (SBP-300WM)
Parapet Mount (SBP-300LM)
ON-CEILING MOUNT TYPE INSTALLATION EXAMPLE
the camera at highly humid place, install it on the ceiling after attaching the enclosed insulation sheet on
I  Inthethebackcaseof ofinstallinstalling
base.
Template
Insulation Sheet
y Wiring Terminal Cables
Connect the cables to the terminal block on the hinged door. For the
location of the wiring pins, please refer to the “Camera Wiring Diagram”
on Page 14. Once the wiring is successful, close the hinged door.
not connect the camera to a power outlet until the installation is complete.
M  DoSupplying
power in the middle of the installation may cause fire or damage the
product.
English - 35
● CONNECTION & INSTALLATION
y Attaching the template and installing the install base
Attach the provided template on the ceiling. Based on the template, drill a 86mm hole in the ceiling and
arrange the wires through the hole. Then, install the install base as shown.
Before installing the exposed bracket, open the hinged door at the bottom of the bracket as shown in the
picture. Hold the Lever on the hinged door to open.
connection & installation
y Setting Up Camera DIP Switches
DIP switches for communication and ID protocols are located on the bottom of the install base.
For the switch settings, refer to the dip switch settings of this manual.
Protocol(SW2)
ID(SW1)
y Connecting Camera Safety Cable and Attaching Camera
Carefully attach the camera to the mount following the alignment guide marks as shown in the picture.
First hook the camera's safety cable on the mount, and then attach the camera.
Safety Cable
Alignment
Direction Guides
Alignment
Direction Guides
Alignment
Directions
Safety Cable Hook
✽ To attach the camera to the mount, refer to the alignment guide marks as shown in the picture.
sure to first hook the camera's safety cable to the mount before proceeding. Otherwise you may be exposed to serious
M  Make
injury caused by a fallen camera.
36_ connection & installation
✽ To attach or detach the camera, refer to the picture.
* Attaching the camera: As shown in the figure, push up the camera body and turn it in the clockwise direction
up to the end. After turning the body fully, fasten the screw on the install base.
* Camera removal : Unscrew the bolt as shown in the figure, and then turn the unit in a counter-clockwise
direction while pushing the hook to the inner side. (The screw may not be fully separated.)
When it is not possible to turn the unit any more, remove it while pulling the camera body
toward the bottom.
<Camera removal>
English - 37
● CONNECTION & INSTALLATION
<Attaching the camera>
connection & installation
EXAMPLE OF INSTALLING AN ENVIRONMENTAL MODEL
❖ Fix the installation base with the bracket
1. Fix the base with the bracket by turning it clockwise.
2. As shown in the figure, lightly pull the hinge door handle in the
side end of the install base and lay it down. Please refer to the
“Camera Wiring Interface Board” on page 14, connect the wires.
not connect the camera to a power outlet until the installation is complete.
J  DoSupplying
power while the installation is in progress may cause fire or damage
the product.
3. Connect the camera safety wire to the installation base.
Safety Cable
38_ connection & installation
4. Assemble Camera and Installation Base
Assemble the installation base and camera by
matching the installation direction guides.
6. Secure Camera and Installation Base
As shown in the picture below, secure the installation
base and camera using 3 hexagon screws.
English - 39
● CONNECTION & INSTALLATION
5. Attach Camera
Turn the camera body installed with the camera in the clockwise direction so that the up,
down reference display becomes the same as the image on the right.
connection & installation
❖ Notes for Waterproofing
This product is an indoor unit. If it is installed outdoors, use the outdoor housing to make it
waterproof.
 Installing the unit on the wall by combining the outdoor housing and wall mount
1. Install the wall mount on the vertical wall.
If the mount is installed on an inclined
wall, moisture can penetrate inside
the outdoor housing through the
external cable.
Concrete wall
Silicon sealant
Wall mount
2. Wrap the screw part of the housing
with a sufficient amount of Teflon tape
for assembly.
3. When separating the dome cover
and fastening it to the housing frame,
make sure that the gasket is not
loosened to separate from the dome
cover.
Screw unit
Teflon tape
4. Install the wall mount adapter for
waterproofing, and apply the silicon
sealant between and around the wall
and wall mount for sealing.
Dome gasket
J  Take particular caution to ensure that there is proper sealing if the installed side is not flat.
40_ connection & installation
 Installing on the wall by combining the outdoor housing and ceiling mount adapter
2. When separating the dome cover
and fastening it to the housing
frame, make sure that the gasket is
not loosened to separate from the
dome cover.
Concrete ceiling
Ceiling mount
adapter
Silicon sealant
Ceiling board
Screw unit
3. Install the ceiling mount adapter for
waterproofing, and apply the silicon
sealant between and around the wall
and ceiling mount for sealing.
Teflon tape
Dome gasket
J  Take particular caution to ensure that there is proper sealing if the installed side is not flat.
English - 41
● CONNECTION & INSTALLATION
1. Wrap the screw part of the housing
with a sufficient amount of Teflon
tape for assembly.
setup
INTERFACE SYMBOLS
y Motion Detection Standby/Operation Display :
When in standby mode, the “
if motion is detected.
” in the upper right of the screen blinks and then changes to “
y Alarm Input Port Status Display :
“1”, “2”, “3”, “4”, “5”, “6”, “7”, and “8” in the upper right of the screen blink.
y Current Alarm Port Display According to Input Alarm Ports(Priority) :
Only one of “ 1”, “ 2”, “ 3”, “ 4”, “ 5”, “ 6”, “ 7”, “ 8” in the upper right of the screen blinks.
Ú The alarm port indicator blinks only when the sequence is set .
y Preset Number Display Settings :
‘*’ : If a preset number is already available
'H' : If a preset location is the camera’s home position
y PTZ Function Screen :
Camera Name
Motion Detect
Alarm Input
Area Display
Sequence Status
Preset Info
ID=001
Area1 Area Name
G-SEQ1
PRESET : 001 Preset Name
P:300 T:040 010X
y Preset Number Setting Screen :
Preset Setting
Preset=011* (1~255)
42_ setup
1234
5678
”
USING AND SETTING THE MENUS
OSD (On-screen Display) Indicators
Has no submenu
● SETUP
Has submenu
Camera Setting
偓Zoom/Focus
White Balance
-----------
ATW
Ú For a mode with “ ” next to it, you can press “Enter” to move to a sub menu.
Operating Your Camera
z Panning and Tilting :
Use the joystick of the controller or its direction buttons.
z Controlling Zoom :
Move the joystick clockwise (Tele) or counterclockwise (Wide), or use the zoom buttons.
z Accessing Screen Menus:
Press the Menu or OSD button on the controller.
more detailed information about controls using a third party controller or a DVR, refer to the user’s manual of the
M  Forproduct.
OSD Commands, Function Chart, and Menu Controls (Applied to
Samsung -T/Samsung-E protocol)
This camera can be operated using two methods: Using hot keys on its dedicated controller, or
accessing the OSD (On Screen Display) on the video output.
The OSD menu commands are as follows:
Command
Function
Move the joystick up/down/left/right
Moves the OSD menus up/down/left/right, respectively.
Enter/Focus Far
Selects a menu and allows access to the sub menus.
ESC/Focus Near
Cancels a command and moves back to an upper-level menu.
English - 43
setup
OSD Menu Chart
You can have an overall view of the menu structure. For more information, refer to the applicable page or
section in the manual.
Zoom/Focus
White Balance
Exposure
Back Light
Camera Setting
AGC
SSNR
SSDR
Day & Night
Others
Preset
Swing SEQ
Group SEQ
Sequence Setting
Tour SEQ
PTZ Trace
Auto Run
Pan/Tilt Limit
Power On Resume
Area Setting
Area Masking
Prop.P/T
P/T Setting
Digital Flip
Image Hold
Jog Speed
Max Speed Level
Camera ID
Camera Name
Preset Number
Preset Name
OSD Setting
Seq. Status
Area Name
PTZ Position
Language
Others
Alarm Enable
Alarm Setting
Alarm Input
Alarm/AUX Output
MD Dwell Time
ALM Dwell Time
Power On Reset
Factory Default Set
Initialize
Camera Default Set
Auto Refresh
Fan Life (Environmental Model)
Password Setting
Status
44_ setup
On/Off
Edit Password
CAMERA SETUP
Zoom and Focus Settings
z Focus Mode
z Zoom Tracking
Through this menu you can set up the camera’s focus mode when
zooming.
- Mode
y AUTO : Auto-focuses when zooming.
y TRACKING : Focuses manually when zooming.
y OFF : Disable the focus modes when zooming. (Full manual
mode)
- Speed
y SLOW/MEDIUM/FAST : Adjusts the zooming speed.
z Digital Zoom
Enables the maximum digital zoom.
Setting the digital zoom to 16x provides a total zoom of 592x.
the optical zoom, the graphics quality of the digital zoom decreases
M  Unlike
as its zoom ratio increases.
 The auto-focus function may not operate normally under the following
conditions :
- When background illumination is low
- While Slow-Shutter is in operation
- If the zoom level is set too high
- When background illumination is too high
- If a long distance object and a close distance object appear together
within a monitoring area
- If there is no contrast, e.g. the sky or a wall
- If the camera is facing a thin horizontal line
 Auto Focus focuses on an object in the center of the screen; objects around
● SETUP
- AUTO : Performs continuous auto-focus.
- MANUAL : Changes the camera mode to Manual Focus.
- ONE SHOT : Auto-focuses the camera once after the Pan,
Tilt, or Zoom function is used.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
ATW
OFF
HIGH
MEDIUM
Æ
Zoom/Focus
Focus Mode
Zoom Tracking
Digital Zoom
ONE SHOT
OFF
the screen edges may not be properly in focus.
English - 45
setup
White Balance
The White Balance menu adjusts the balance of the screen colors
under different lighting conditions.
z ATW : Adjusts the screen color automatically.
(Color Temperature:1800~10500°K)
z ATW(IN) : Adjusts the screen color to be optimal in an indoor
environment. (Color Temperature:4500~8500°K)
z ATW(OUT) : Adjusts the screen color to be optimal in an outdoor
environment. (Color Temperature:1700~11000°K)
z AWC : To obtain the optimal condition for the current lighting, put
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
the focus of the camera to a white paper and press the
SET button. If the lighting environment is changed, you
should readjust the settings accordingly.
Æ
Camera Setting
z MANUAL : Enables customization the Red and Blue gains.
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
ATW
OFF
HIGH
MEDIUM
M  White Balance may not work properly under the following conditions.
➊ When the color temperature of the environment surrounding the subject is out of the control range.(e.g. Clear sky or sunset)
➋ When the ambient illumination of the subject is dim.
➌ If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, White
Balance adjustments may not deliver consistent results.
46_ setup
Exposure
The Exposure settings are to control the camera’s exposure meter.
z Brightness : Adjusts the screen brightness.
z Iris
- AUTO : Automatically adjusts the exposure meter.
- MANUAL : Enables manual adjustment of the exposure meter.
(F1.6~Close: 18 levels)
z Shutter : Controls the camera’s electronic shutter.
- --- : The shutter speed is fixed at 1/60 for NTSC and 1/50 for
PAL. Operates when Iris is on the Auto Mode.
- ESC : Adjusts the shutter speed automatically according to
the screen brightness. Operates when Iris is on the
Manual Mode.
- A.FLK : Select this setting when you experience picture
flickering. Flickering can happen when artificial lighting
frequencies clash with camera frame rates.
- MANUAL : Enables manual adjustment of the shutter speed.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
(Over 50: Brighter, Under 50: Darker)
Main Menu
Æ
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
z Sens-Up
- AUTO : Automatically detects light levels and maintains a clear SSNR
SSDR
picture at night or under low-light conditions.
Day & Night
- Sens-Up Limit : Adjusts to the maximum-powered zoom per
frame.
Others
ATW
OFF
HIGH
MEDIUM
Æ
Exposure
performance of the A.FLK mode, avoid using the mode in conjunction
M  Forwithoptimal
Backlight.
Brightness
Iris
Shutter
Sens-Up
050
AUTO
--AUTO
 While the Internal Sync mode is in effect, setting the shutter to ‘---’ and facing the
camera directly to a bright light source may cause poor camera performance.
 Sens-Up is disabled when the shutter is in Manual or A. FLK mode.
English - 47
setup
Back Light
The Backlight function is dedicated to SV-V DSP (SCP-3371) or W-V
DSP (SCP-2XX1) chip, developed by Samsung Techwin, which,
unlike the old models, provides a sharp image of both object and
background against a severe counter-light condition.
z Back Light Mode
- OFF : Disables the Backlight mode.
- WDR : Activates the Wide Dynamic Range mode.
- HLC : Activates the High Light Compensation mode.
- BLC : Activates a user defined backlight compensation mode.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
ATW
OFF
HIGH
MEDIUM
” WDR (SCP-3371 Series)
When there are both bright and dark areas at the same time, this
mode makes both areas distinctive.
WDR Setting
Limit
Level
Mode
Anti Rolling
WDR ON
MEDIUM
050
INDOOR
OFF
WDR OFF
- Limit : Three WDR sensitivity levels are available in 3: Low, Medium , and High.
Note that the higher the sensitivity level, the lower the contrast in the light and dark areas becomes.
- Level : Adjusts the screen brightness in WDR mode.
48_ setup
- MODE : Select a mode that is suitable to the indoor or outdoor backlight condition.
- ANTI ROLLING : Reduces the difference of ambient colors to lessen the rolling that occurs under the
fluorescent lighting.
M  If you set both Iris and Shutter to “MANUAL”, WDR will be disabled.
they occur, stop using WDR.
” HLC Setting
When a bright light enters a limited environment such as
apartment parking lot entry or gas station entry, this function
masks only the bright light so that items such as car license plate
number can be monitored effectively.
HLC Setting
Level
Mask Tone
MEDIUM
07
HLC is disabled during the daytime. While monitoring nigh time
car traffic, if car headlights reflects too much bright light on the screen, the camera automatically
eliminates the headlamp lights and adjusts the color of the license plate accordingly.
HLC Masking Area
<HLC ON>
<HLC OFF>
- Level : Adjusts the HLC sensitivity level.
- Mask Tone : Adjusts the mask color on the high lighted area.
M  Even if HLC is on, car license plates may not be detectable depending on the location and angle of the camera as well as
the lighting condition.
 For SCP-2xx1 series, the HLC function will be disabled while using Digital Zoom, Freeze or Stabilizer. (However, SCP-3371
can enable HLC with any of these functions.)
English - 49
● SETUP
 If you are using VPS, WDR will be disabled.
 During WDR operation, noise, discoloration, spots, and whitish symptoms may occur depending on lighting conditions. If
setup
” BLC Setting
You can selectively choose a screen area to see objects within the
area more clearly than others.
BLC
MEDIUM
- Four-direction Joystick Controls :
Moving the joystick in all four directions—upward, downward,
left, and right—adjusts the location and size of a selected area.
- Zoom Control :
y Zoom Tele : Enlarges the size of a selected area.
y Zoom Wide : Reduces the size of a selected area.
1 + PST : Level Change
m: Up n: Down
k: Left l: Right
W: Decrease T: Increase
AGC(Auto Gain Control)
AGC (Automatic Gain Control) adjusts the camera’s gain control
and the screen brightness if the camera has captured an object
under low-light conditions.
z OFF:
AGC does not function.
z LOW/MEDIUM/HIGH:
As the level increases to HIGH, brighter the captured screen in a
dark lighting.
z MANUAL:
AGC can be fine tuned by adjusting the level (5dB ~ 41dB).
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
50_ setup
ATW
OFF
HIGH
MEDIUM
SSNR(Samsung Super Noise Reduction)
SSNR significantly reduces the amount of low luminance noise.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
- OFF : Disables the noise reduction function.
- LOW : Reduces only a small amount of noise, but generates
almost no afterimage.
- MEDIUM : The most commonly used mode. Reduces a suitable
amount of noise while generating a subtle afterimage.
- HIGH : Reduces noise significantly, but generates obvious
afterimages.
Æ
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
ATW
OFF
HIGH
MEDIUM
M  SSNR is not available if AGC is set to OFF or MANUAL.
English - 51
setup
SSDR(Samsung Super Dynamic Range)
SSDR illuminates darker spots of an image while retaining the same
light level for brighter spots to even out the overall brightness of the
image with high contrast between bright and dark spots.
SSDR ON
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
SSDR OFF
Æ
Camera Setting
- Mode : Enables or disables SSDR.
- Range : Defines a range of SSDR. (SCP-2371 Series)
- Level : Changes the contrast between bright and dark spots by
the level.
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
ATW
OFF
HIGH
MEDIUM
Æ
SSDR
Mode
Range
Level
52_ setup
ON
NARROW
08
Day & Night
The Day & Night function allows the camera to switch between the
Color and B/W modes.
- AUTO : Operates in Color mode most times, and switches
to B/W mode if a low light level is detected during
nighttime.
- COLOR : Operates in Color mode at all times.
- B/W : Operates in B/W mode at all times. By using the Burst
On/Off sub menu, burst signals can be retained or
disabled.
Ú If the camera is in B/W mode and connected to equipment
that requires external sync through burst signals, set the Burst
On/Off option to “On”.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
z MODE
Main Menu
Æ
Camera Setting
z Duration :
- The camera’s light sensitivity is adjustable as in the chart
below. The camera’s ambient light diversion performance
may vary depending on its environment.
Color p B/W
B/W p Color
FAST
2.5Lux
4Lux
SLOW
0.8Lux
6Lux
z Dwell Time :
- The duration of both the lighting conditions can be customized to
let the camera divert between the daytime and nighttime settings.
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
ATW
OFF
HIGH
MEDIUM
Æ
Day/Night
Mode
Duration
Dwell Time
AUTO
SLOW
05 SEC
M  Auto mode is not available if AGC is set to OFF or MANUAL. Only available if it is set to COLOR or B/W.
 Using B/W mode under sunlight or a halogen lamp may decrease the focusing performance.
English - 53
setup
Others
z Sync : Select Internal or Line Lock.
- INTERNAL : Synchronizes the camera’s output timing to the
internal crystal.
- LINE LOCK : Synchronizes the camera’s output timing to
the AC adapter power to synchronize multiple
cameras. This option is useful when using a
switch such as Matrix Switcher.
- LINE LOCK PHASE : Enables setting the adapter’s
synchronization phase between 0 and 359°.
z Image Adj :
- Sharpness : Sharpens outlines of an image.
- Color : Adjusts the color density of an image.
z Freeze : Stops or reanimates an image.
z Stabilizer : The Stabilizer compensates for any small
movements of the camera caused by due to the
wind and other reasonable causes
Stabilizer uses the digital zoom and may cause low picture quality.
M  The
The Stabilizer is disabled if the ambient light is too low.
 The Stabilizer is disabled if the field of view has very low or no contrast,
e.g. The sky or a white wall.
z VPS (Virtual Progressive Scan) (SCP-3371 Series) :
Virtual Progressive Scan provides a clearer view of objects,
which is used for high-quality video. It is suitable for
highquality recording and Internet transfer.
- OFF : Switch the video recording system to 2:1 Interlace Scan.
- ON : Switch the video recording system to Virtual Progressive Scan.
z PIP (Picture in Picture) (SCP-3371 Series) :
PIP enables you to display the main image along with a
collapsed version of the main image.
M  The PIP feature will be disabled if using Area Masking.
z Dome Cover (Indoor Model) :
The existence of the dome cover will minimize the quality
difference according to the image formation position.
- OFF : If removing the dome cover before use
- ON : If using the product by factory default (using the dome cover)
54_ setup
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Camera Setting
Zoom/Focus
White Balance
Exposure
Back Light
AGC
SSNR
SSDR
Day & Night
Others
ATW
OFF
HIGH
MEDIUM
Æ
Others
Sync
Image Adj
Freeze
Stabilizer
VPS
PIP
Dome Cover
INTERNAL
OFF
OFF
OFF
OFF
ON
Sequence Setting
Preset
z Setting Up Preset Numbers :
Selecting the Preset Setting menu brings up a screen as shown
below. Move the joystick in all four directions to select the desired
number.
Preset Setting
Preset = 001 (1~255)
001 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ
041 : þþþþþþþþþþþþþþþþþþþþ
061 : þþþþþþþþþþþþþþþþþþþþ
081 : þþþþþþþþþþþþþþþþþþþþ
101 : þþþþþþþþþþþþþþþþþþþþ
121 : þþþþþþþþþþþþþþþþþþþþ
z Saving Preset Locations :
Selecting a preset number and pressing the Enter key redirects
the menu to the screen shown below.
Using the joystick, adjust the location of the Pan and Tilt
functions and then set the Zoom and Focus command.
In Preset mode, the zooming focus can be controlled only by the
zoom command.
Preset Setting
Main Menu
● SETUP
This function enables the memorization of a selected location and
activates the Pan, Tilt, and Zoom functions at that location. Saved
locations can be recalled using the Preset Execute command.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
ON
Æ
Preset
Setting
Edit
Home Position
Execute
Clear
Status
OFF
1+PST:ZOOM 2+PST:FOCUS
English - 55
setup
” PTZF Setting
1. If you open the PTZF setup menu, you will see the following
window. You can use the joystick to select a desired number.
Preset Setting
Preset = 001 (1~255)
2. Select a preset number and press ENTER. You will move
to the setup screen.
Using the joystick, adjust the location of the Pan and Tilt
functions and then set the Zoom and Focus command.
In Preset mode, the zooming focus can be controlled only
by the zoom command.
For switching modes, refer to the menu bar in the bottom.
001 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ
Æ
Preset Setting
1+PST:ZOOM 2+PST:FOCUS
” Edit
With this feature, you can edit or save the video-related settings
for each preset of the camera.
- PTZ : Recalls saved locations using the Preset Settings command.
- Focus : Refer to the section entitled Setting Up Your Camera.
- Brightness : Refer to the section entitled Setting Up Your Camera.
- Iris : Refer to the section entitled Setting Up Your Camera.
Preset
Setting
Edit
Home Position
Execute
Clear
Status
- Back Light : Refer to the section entitled Setting Up Your Camera.
OFF
Æ
- Day & Night : Refer to the section entitled Setting Up Your Camera.
- After Action (SCP-2xx1 Series)
: Enables setting up an automatic action after the camera arrives
at a selected preset location.
. MD : Commands the camera to perform the Motion Detection function.
If Focus mode is set to Auto, the MD function may not work
properly in a challenging environment.
. OFF : Select this when no action is desired.
series model, please refer to the “Intelligent Video”
M  Forsettingthe inSCP-3371
the next page.
- Scene Adj : You can set AGC, Stabilizer, SSNR, SSDR, Shutter,
Sens-Up and White Balance functions. For terms
related to settings, refer to the camera settings
commands.
56_ setup
Preset Edit
Preset = 001Ã (1~255)
001 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ
Æ
Preset Edit
[001]
PTZ
Focus
Brightness
Iris
Back Light
Day & Night
After Action
Scene Adj
XXX/XXX/XXX
ONE SHOT
050
AUTO
OFF
AUTO
OFF
❖ Intelligence (SCP-3371 Series)
This will enable you to detect and trace a moving object.
SCP-3371 series support the intelligent motion detection feature.
For the compatibility of this feature, refer to the table below.
Features Applied
SCP-2371/2371H/2271/2271H
OFF / MD
SCP-3371/3371H
OFF / Detection / Tracking /
Fixed/Moved
z Detection :
[001]
PTZ
Focus
Brightness
Iris
Back Light
Day & Night
Intelligence
Scene Adj
180/025/1X
ONE SHOT
050
AUTO
OFF
AUTO
OFF
Perform the intelligent motion detection.
Detection
- Detect Box: Display an object in a box that is detected to move in
your specified type.
Detect Box
- Detect Area : You can specify a motion detection area.
Detect Area
- Mask Area : You can specify an exceptional area to motion
Mask Area
detection by masking the area.
Sensitivity
You can set up to 4 areas, for each of which you can
Det. Size
change the mask coordinates.
- Sensitivity : Specify the sensitivity level of the motion detection.
The lower the level is, the stronger the sensitivity becomes.
- Detect Size : Specify the size of an object to detect on the screen.
The higher the level is, the greater the size becomes.
ON
3
3
z Fixed/Moved :
Detect if an existing object (on the screen) disappears or if an object appears from nowhere and
stays for a certain time.
M  In following situations, FIXED/MOVED detection may not work properly.
➊ If multiple motions continue at random.
➋ If a fixed object continues to move in the same position.
➌ If a newly appearing object conceals another object that is moving.
 5 to 15 seconds of recognition time is required if the [Intelligence] function is activated.
 The focus mode will be controlled manually if [Intelligence] is enabled.
 The performance of [Intelligence] may be deteriorated if the camera vibrates due to unstable installation.
English - 57
● SETUP
Model
Preset Edit
setup
z Tracking :
This will detect and trace a moving object. You can use the fence
function to count the moving objects. The default setting is the
same as in the Detect menu, to which the Fence Position function
is added.
- Fence : Specify the position and detectable direction of the line
fence or area fence, depending on the fence type.
y Display: Specify the display of the fence status.
y Type : You can select one of two types for the fence LINE and
AREA.
y Count : Display the number of times that an object enters or
exits from the fence.
M
 In some cases, the Count function may have a difference between number
of the detected objects and counter number.
y Fill : Specify the use of color fi lling on the selected fence.
Tracking
Fence
Detect Box
Detect Area
Mask Area
Sensitivity
Det. Size
ON
3
3
Æ
Fence
Display
Type
Count
Fill
Position
ON
LINE
ON
ON
y Position : Specify the position and detectable direction of the line
fence or area fence, depending on the fence type.
 LINE FENCE
- SEL POS: Select a changing point from position 1 and
position 2.
- X POS/Y POS: Specify the position of the changing point that
you have selected in the SEL POS menu.
- DIRECTION:
Fence
SEL POS
X POS
Y POS
Direction
POS1
25
01
DIR 1
DIR 1: Detect an object that moves from left to right based on the specified fence line.
DIR 2: Detect an object that moves from right to left based on the specified fence line.
DIR 1/2: Detect an object that moves in any direction of right to left or left to right based on the
specified fence line.
 AREA FENCE
- SEL POS:Select a changing point from position 1 through
position 4.
- X POS/Y POS:Specify the position of the changing point that
you have selected in the SEL POS menu.
Fence
SEL POS
X POS
Y POS
Direction
- DIRECTION:
IN: Detect any object that enters the specified fence area.
OUT: Detect any object that exits from the specified fence area.
IN/OUT: Detect any object that enters or exits from the specified fence area.
58_ setup
POS1
20
20
IN
” Preset Name Setting
Using this function, you can add names to preset locations
up to 12 characters.
Once a name is entered, use the joystick and the Enter key to
perform the Set command and save the name.
Main Menu
● SETUP
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
OSD Setting
Camera ID
Camera Name
Preset Number
Preset Name
....
ON
ON
Æ
Preset Name
On/Off
Edit
OFF
Æ
Preset Name
Preset = 001* (1~255)
001 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ
Æ
Preset Name [
" # $ % & '( ) * + , - .
/0123456789:;
BCDEFGHIJKLMN
OPQRSTUVWXYZ[
<> T Â ]
BACK SPACE CLR SET
English - 59
setup
” Home Position
Sets one of the currently configured preset positions as the home
position.
The Home Position option is the location to move after booting.
” Execute
Preset
Setting
Edit
Home Position
Execute
Clear
Status
OFF
Preset
Recalls a saved preset location.
While in Sequence mode operation, the actual movement can
be slower than the specified when moving the camera in the
direction of Pan and Tilt at the same time.
” Clear
Setting
Edit
Home Position
Execute
Clear
Status
OFF
Preset
Deletes the selected preset location.
Setting
Edit
Home Position
Execute
Clear
Status
OFF
” Status
Opens a map of saved preset locations.
An area saved as a preset location is displayed with the ‘ ’ icon.
Preset Status
Preset Status
001 : þþþþþþþþþþþþþþþþþþþþ 141 : þþþþþþþþþþþþþþþþþþþþ
021 : þþþþþþþþþþþþþþþþþþþþ 161 : þþþþþþþþþþþþþþþþþþþþ
041 : þþþþþþþþþþþþþþþþþþþþ 181 : þþþþþþþþþþþþþþþ þþþþþ
061 : þþþþþþþþþþþþþþþþþþþþ 201 : þþþþþþþþþþþþþþþ þþþþþ
081 : þþþþþþþþþþþþþþþþþþþþ 221 : þþþþþþþþþþþþþþþ þþþþþ
101 : þþþþþþþþþþþþþþþþþþþþ 241 : þþþþþþþþþþþþþþþ
121 : þþþþþþþþþþþþþþþþþþþþ
60_ setup
Preset
Setting
Edit
Home Position
Execute
Clear
Status
OFF
Swing SEQ
The Swing function commands the camera to move between 2
selected locations, monitoring the route.
Activates the Pan function for the Swing operation.
z Tilt Swing :
Activates the Tilt function for the Swing operation.
z P/T Swing :
Activates both the Pan and Tilt functions for the Swing operation.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
z Swing Setting/Execute/Clear
Each of the Swing menus have sub menus with the settings.
Pan Swing Set
Setting
Execute
Clear
Æ
Pan Swing Set
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
[ÂÂÂ]ƒ„[ÂÂÂ]
SPEED =64 (1~64)
DWT =005(1~120) (s)
● SETUP
z Pan Swing :
Main Menu
ON
Æ
Swing SEQ
Pan Swing
Tilt Swing
P/T Swing
Select 2 preset locations by using the joystick.
Speed indicates the camera’s movement speed. DWELL TIME indicates the camera’s duration of stay at a
preset location.
- Execute: Executes the Swing operation.
- Clear: Deletes data in the Swing memory.
in Sequence mode operation, the actual movement can be slower than the specified when moving the camera in the
M  While
direction of Pan and Tilt at the same time.
English - 61
setup
Group SEQ
Selecting Group SEQ recalls a group of multiple preset locations in a
consecutive manner. Up to 6 groups can be defined and up to 128
presets can be memorized for each group.
z Setting :
Using the joystick,enter desired preset numbers into the PSET
section. DWT indicates the camera’s duration of stay at a preset
location.
The speed is adjusted in 64 levels.
Group SEQ 1
NO
001
002
003
004
005
006
007
PSET
***
***
***
***
***
***
***
DWT(s)
003
003
003
003
003
003
003
SPD
64
64
64
64
64
64
64
z Execute :
Executes the group operation.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
Æ
z Clear :
Deletes the selected group.
8 seconds of recognition time is required if [Intelligence] of the preset
M  About
is activated from the Group menu.
 For a proper operation of [Intelligence], set [Time (sec)] of the Group menu
to more than 8 seconds.
62_ setup
Group SEQ
Group 1
Group 2
Group 3
Group 4
....
Æ
Group SEQ 1
Setting
Execute
Clear
ON
Tour SEQ
Selecting Tour SEQ recalls groups of preset locations in a
consecutive manner. Up to 6 groups can be listed for this function.
Selecting the Settings menu brings up the following screen.
Using the joystick, you can enter desired group numbers to the
Group section. DWT indicates the camera’s standby time before
a new group is recalled.
Tour SEQ
NO
01
02
03
04
05
06
GROUP DWT(s)
*
003
*
003
*
003
*
003
*
003
*
003
z Execute :
Executes the group operation.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
z Setting :
Main Menu
Æ
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
z Clear :
ON
Æ
Deletes the selected group.
Tour SEQ
Setting
Execute
Clear
English - 63
setup
PTZ Trace
Maximum 4 patterns of the manual operation paths (for Pan, Tilt,
Zoom and Focus) are memorized and replayed.
z Replay :
Replays a route saved by the Trace function.
z Replay Once :
Replays a saved Trace route once.
z Memorize :
The time for storing the event differs depending on the
complexity of PTZ operations of your choice.
When the memory becomes full, saving will be automatically
terminated.
When saving continues for more than 2 minutes, the saving job
will be automatically terminated.
While in saving mode, the saving job may be terminated using
the Menu (OSD entry) key.
Ú Using other protocols
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
Protocol
Representative
Model
Stop saving the
trace
PELCO-D/P
KDB300A
Ack, Iris Open
SAMSUNG-E
SSC-5000
OSD ON, Iris Open
PANASONIC
WV-CU161C
OSD ON
VICON
V1300X-DVC
Iris Open
PTZ Trace
HONEYWELL
HTX-3000
Iris Open
Trace 1
Trace 2
Trace 3
Trace 4
OSD ON, Iris Open
AD
GE
KTD-405
Bosch
Iris Open
Iris Open
Æ
Æ
z Clear : Deletes a saved Trace route.
PTZ Trace
Replay
Replay Once
Memorize
Clear
64_ setup
ON
Auto Run
If there is no controller operation by the user for a certain time, the
sequence operation designated by the user will be executed.
- HOME : Auto run Home Position (Refer to the Preset Menu.)
- PRESET : Auto run a selected preset number.
- SWING : Auto run a selected Swing mode.
- GROUP : Auto run a selected Group mode.
- TOUR : Auto run a selected Tour mode.
- TRACE : Auto run a selected trace mode.
- A.PAN : Auto run a 360-degree pan. To activate the
panning command, you need to set up the
camera’s tilt angle and auto pan speed manually.
- SCHEDULE : Execute Auto Run on the selected day of the
week.
z Time :
Enables setting up an Auto Run duration. (The duration can be 5~30
seconds, or 1~5 minutes.)
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
z Mode :
Main Menu
Æ
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
ON
Æ
Auto Run
Mode
Time
OFF
30 SEC
English - 65
setup
” Schedule
Schedule enables you to schedule a sequencing action by day and time.
z Select Day :
At Auto Run, select SCHEDULE to set up each day of the week,
as shown on the side picture. Select a day, change to ON, and
then press Enter.
z Select Time :
When turning ON a day, a timetable appears as shown on the
side picture. (Up to 6 timelines can be selected for a day.) Select
the beginning time and sequencing action to schedule the action.
Auto Run
Mode
Time
SCHEDULE
30SEC
Æ
AutoRun Mode Set
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
ON
OFF
OFF
OFF
OFF
OFF
OFF
Æ
Schedule Set
No START
1
09:00
2
00:00
3
00:00
4
00:00
5
00:00
6
00:00
Clear
SEQ
HOME
OFF
OFF
OFF
OFF
OFF
No
Power On Resume
Main Menu
z Power On Resume :
This is useful when the power is disconnected and reconnected
due to power failures or other power interruptions.
If the camera was performing a sequence action prior to a power
disconnection, the camera automatically resumes the action
when the power is reconnected.
Camera Setting
Sequence Setting
P/T Setting
Æ
Sequence Setting
Preset
Swing SEQ
Group SEQ
Tour SEQ
PTZ Trace
Auto Run
Power On Resume
66_ setup
ON
P/T Setting
Pan/Tilt Limit
Main Menu
z Position :
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Selecting the Position menu brings up the following screen if it is
for the Pan Limit setting. Move the joystick left and right to select
a movement range from the starting point to the end.
START LIMIT
END LIMIT
Enter: Set ESC: Exit
Enter: Set ESC: Exit
● SETUP
The moving ranges in the Pan/Tilt directions can be limited.
Æ
P/T Setting
The following picture shows the Tilt Limit setting.
Move the joystick left and right to select a movement range from
the starting point to the end.
START LIMIT
END LIMIT
Enter: Set ESC: Exit
Enter: Set ESC: Exit
z Activation :
Sets the configured Pan/Tilt Limit function to use or not.
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Jog Speed
Max Speed Level
ON
ON
OFF
MANUAL
5
Æ
Pan/Tilt Limit
Pan Limit
Tilt Limit
Æ
Pan Limit
M
 With its maximum wide angle, the camera’s field of view may be
blocked if reached the both ends of tilting angle. In such cases, the
amount of blocked portions at both ends may be different.
Position
Activation
OFF
English - 67
setup
Area Setting
The Area Setting menu enables selecting certain locations in the course
of the Pan and Tilt operation, and then display the areas with the OSD
(On Screen Display) texts when the camera passes through them. Up to
8 areas can be selected.
z Area Name :
You can add names to selected areas. Names can be up to 12
characters and can be entered via the joystick and the Enter key.
Once a name is entered, use the joystick and the Enter key to
perform the Set command and save the name.
Area Name
[
]
" # $ % & '( ) * + , - .
/0123456789:;
BCDEFGHIJKLMN
OPQRSTUVWXYZ[
<> T Â BACK SPACE CLR SET
z Position :
As shown in the picture below, move the joystick to select the upper
left corner and lower right corner of an area.
Area Setting
Area Setting
Enter: Set ESC: Exit
Enter: Set ESC: Exit
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Jog Speed
Max Speed Level
ON
ON
OFF
MANUAL
5
Æ
Area Setting
The effective positioning range is between -45° and 40° in the tilting
angle at the zoom factor of 1x.
z Activation :
Cancels or activates the display function of selected areas.
Area 1
Area 2
Area 3
Area 4
....
Æ
Area Setting
Area Name
Position
Activation
68_ setup
OFF
Area Masking
If a monitoring location includes a highly private area, the area can be selectively excluded from monitoring.
Main Menu
z Position :
Area Masking
Area Masking
Enter: Set ESC: Exit
Enter: Set ESC: Exit
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
- SCP-2XX1Series
As shown in the picture below, move the joystick to select the upper
left corner and lower right corner of an area.
Æ
- SCP-3371 Series
As shown, specify the masks in the order of: top left p top right p
bottom right p bottom left.
Area Masking
Area Masking
Enter: Set ESC: Exit
Enter: Set ESC: Exit
Area Masking
Area Masking
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Jog Speed
Max Speed Level
ON
ON
OFF
MANUAL
5
Æ
Area Masking
Enter: Set ESC: Exit
Enter: Set ESC: Exit
Use the joystick in four directions to specify the masks that you want
to exclude from the area masking.
z Activation :
Activate or deactivate the display of specified masks.
Mask 1
Mask 2
Mask 3
Mask 4
....
Æ
Area Masking
Position
Activation
OFF
English - 69
setup
Prop. P/T
This commands the camera to change the Pan and Tilt speed
automatically according to the current zoom ratio. Moving the
joystick clockwise (Tele) slows down and counterclockwise (Wide)
accelerates the Pan and Tilt speed, allowing detailed adjustments.
Turning this “Off” executes the function the optical 1x zoom speed
regardless of how far the lens is zoomed in.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Jog Speed
Max Speed Level
70_ setup
ON
ON
OFF
MANUAL
5
Digital Flip
z 0° → 180° : Image flip at the 93-degree point
z 180° → 0° : Image flip at the 87-degree point
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
Digital Flip is useful to monitor a moving object or a person passing
directly under the camera.
When the object passes straight under the camera, tilting can be
traced up to the opposite tilting area without the need of the pan
operation. The reverse screen that occurs when the object gets
through the 90-degree point will be corrected in digital processing.
Æ
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Jog Speed
Max Speed Level
ON
ON
OFF
MANUAL
5
English - 71
setup
Image Hold
This will display the preset video in still images until the orientation
of the camera reaches the preset position at a group or tour
movement.
This is useful if you want to monitor the video while preventing a
possible visual distraction of the observer.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Jog Speed
Max Speed Level
72_ setup
ON
ON
OFF
MANUAL
5
Jog Speed
You can adjust the speed of the pan or tilt operation. The pan/tilt speed changes according to the tilt of
the joystick, or you can control the operation in a fixed speed.
The pan/tilt speed depends on how much the joystick of the
controller is tilted. The more the joystick is tilted, the faster the
operation is performed.
z 30/35/40/45/50/55/60 :
The pan/tilt operation will be performed at the selected speed; the
greater the number is, the faster the operation is performed.
However, the speed at each level may differ according to the
zooming status, and depending on the use of synchronized
zooming.
● SETUP
z MANUAL :
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Jog Speed
Max Speed Level
ON
ON
OFF
MANUAL
5
English - 73
setup
Max Speed Level
Adjusts the maximum speed of Pan and Tilt while performing the Preset and Sequencing actions.
z 1~5 :
Pan and Tilt operations can be set up to 500°/ sec.
Ú Preset speed for each level
Level
Speed (Unit: º/sec)
5
500
4
450
3
400
2
360
1
300
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
M  The Pan/Tilt speed will be reduced at below -40°.
74_ setup
P/T Setting
Pan/Tilt Limit
Area Setting
Area Masking
Prop. P/T
Digital Flip
Image Hold
Jog Speed
Max Speed Level
ON
ON
OFF
MANUAL
5
OSD SETTING
In this menu, you can configure the OSD (On Screen Display) settings.
z Camera ID :
z Camera Name :
Add a name to the camera. (see the top note on page 76 for
more information.)
z Preset Number :
Displays or hides Preset Numbers on the screen.
z Preset Name :
Add names to preset locations. (see the top note on page 76 for
more information.)
z Seq. Status :
Displays or hides the status of a sequence action that is in
progress.
z Area Name :
Displays or hides the Area Name for the Area Settings on the
screen.
z PTZ Position :
Displays or hides the status of the Pan, Tilt, and Zoom operation
that is in progress.
z Language :
Main Menu
● SETUP
Displays or hides Camera ID in the upper left of the screen.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
OSD Setting
Camera ID
Camera Name
Preset Number
Preset Name
Seq. Status
Area Name
PTZ Position
Language
Others
ON
ON
ON
OFF
ON
ENGLISH
Enables changing the system language. This camera supports
ENGLISH, CHINESE, FRENCH, GERMAN, SPANISH, ITALIAN, PORTUGUES, POLISH, RUSIAN,
CZECH, TURKISH, KOREAN, JAPANESE, TAIWANESE.
z Others
- Direction : Indicates the current angle of the camera:
East, West, South, North, Southeast, Southwest, Northeast, or Northwest.
 Set North Dir. : Specify the azimuth of the north manually.
- Clock Setting: You can specify the time information manually that will be displayed on the
screen. This will synchronize with Sequence so that you can set it to activate
on a specific time and date.
 Display: Specify the use of time display on the screen.
 Date Format: Specify the date format. (DD/MM/YYYY, MM/DD/YYYY)
 Set Date: Enter a desired date manually.
 Time Format: Specify the time format. (24hr / 12hr)
 Set Time: Specify the time manually.
English - 75
setup
XXX Name
[
]
" # $ % & '( ) * + , - .
/0123456789:;
BCDEFGHIJKLMN
OPQRSTUVWXYZ[
<> T Â selecting the Camera Name and Preset Name, the screen displays the Left
M  When
keypad.
 Names can be up to 12 characters and can be entered via the joystick and the Enter
key. Once a name is entered, use the joystick and the Enter key to perform the Set
command and save the name.
BACK SPACE CLR SET
ALARM SETTING
Alarm Enable
Main Menu
z ON/OFF :
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Enables or disables the Alarm function.
Alarm Input
z MOD
Enables selecting an Alarm Input method.
- NO (Normally Open)
IN 1.2.3.....8
IN 1.2.3.....8
Æ
Ä
ALM GND
Alarm Setting
ALM GND
ALARM OFF
ALARM ON
< Alarm input when N.O. is enabled >
- NC (Normally Closed)
IN 1.2.3.....8
IN 1.2.3.....8
OFF
OFF
HOLD
Æ
ALM MOD P SEQ. NO
Ä
ALM GND
Alarm Enable
Alarm Input
Alarm/AUX Output
MD Dwell Time
ALM Dwell Time
ALM GND
ALARM ON
ALARM OFF
< Alarm input when N.C. is enabled >
IN1 OFF
IN2 OFF
IN3 OFF
.....
1 OFF
2 OFF
3 OFF
shown in the picture above, the Alarm Input must be entered with the Open or Closed switch signals. Supplying power
M  Aswithout
entering the signals may damage the product.
76_ setup
z P(Priority) :
Set the priority of Alarm Inputs. If more than one alarm is simultaneously activated,
the alarm with the highest priority activates before the others.
z SEQ. :
● SETUP
Enables setting up a sequence action for the camera in response to an alarm.
You can configure the settings of: HOME/PRESET/SWING/GROUP/TOUR/TRACE/A.PAN/OFF
Alarm/AUX Output
Main Menu
z Setting 1, 2, 3 :
Enables selecting an Alarm Output method.
- DETECT MODE : Displays the alarm input ports (1~8) and the
motion detection input. If you set MD Input,
you can select one from: OFF/MD.
- AUX MODE : Both Alarm OUT/AUX OUT 1 and 2 are NC/NO
while Alarm OUT/AUX OUT 3 performs NO only.
z Timer 1, 2, 3 :
- On : Retains an alarm output for a set duration from a
minimum of 1 second to a maximum of 60 minutes upon
the alarm occurrence.
- MOMENT : The output operation will last until an alarm/AUX event
is released since its occurrence.
- The Alarm/AUX output system is equipped with a relay circuit,
whose output port operates as below: (based on “NO”)
/0
$0.
/$
Alarm Out OFF
/0
Ä
$0.
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Alarm Setting
Alarm Enable
Alarm Input
Alarm/AUX Output
MD Dwell Time
ALM Dwell Time
/$
Alarm Out ON
z OUT Off 1, 2, 3 :
- Output of an alarm/AUX event can be forcibly terminated
when it occurred.
OFF
OFF
HOLD
Æ
Alarm/AUX Output
Setting
Setting
Setting
Timer
Timer
Timer
Out Off
Out Off
Out Off
1
2
3
1
2
3
1
2
3
DETECT MODE
DETECT MODE
DETECT MODE
OFF
OFF
OFF
English - 77
setup
the power connector and GND incorrectly to the NC/NO and COM ports may cause a short circuit and fire,
M  Connecting
damaging the camera.
 The maximum power capacity of the built-in relay is 30VDC/2A, 125VAC/0.5A, and 250VAC/0.25A. Operating the
camera beyond the capacity may decrease the camera’s lifespan and damage it.
MD Dwell Time
When Motion Detection under the Preset Edit menu is selected,
MD Dwell Time performs the Tour or Group function.
While the camera is performing a sequence action, if motion is
detected from a selected preset location, the camera pauses the
sequence action operation and starts monitoring the location instead
for a duration that is set under the MD Dwell Time menu.
If the motion is no longer detectable or the duration expires, the
camera aborts the monitoring operation and then resumes the
sequence action.
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Alarm Setting
Alarm Enable
Alarm Input
Alarm/AUX Output
MD Dwell Time
ALM Dwell Time
OFF
OFF
HOLD
ALM Dwell Time
You can specify the time of sequence operation that will be activated if an event occurs from the alarm
input.
z SET:
The sequence operation will proceed for a specified time.
z HOLD:
The sequence operation will be maintained until the user deactivates it.
78_ setup
INITIALIZE
z Power On Reset :
Restarts the camera.
z Factory Default Set :
z Camera Default Set :
Reset the zoom module of the camera to the factory default. Use
this if you want to return the camera settings of such as Exposure
or Backlight to the factory default.
z Auto Refresh :
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
● SETUP
Enables resetting the camera to its factory default settings. When
the mode is selected, all custom data such as preset locations is
deleted from the camera.
Use this function if it is necessary to reset the settings of the
camera.
[Current Time], [Language] and [Fan Life] values maintain the
current values rather than the default values.
Main Menu
Æ
Initialize
Optimizes the settings of the electric circuits and component parts
Power On Reset
of the camera on a regular basis.
This is useful for maintenance purpose, especially when the
Factory Default Set
camera faces a specific light source, or if the camera settings are
Camera Default Set
not maintained properly due to an extended time of recording
Auto Refresh
OFF
while rotating the camera in four directions.
- Off, 1~7 Days : Selecting Off disables Auto Refresh and selecting Fan Life
1~7 Days automatically executes it after 1~7 days has passed.
Ú Auto Refresh takes about 10 seconds or less. Any sequence operation that is being performed will
be stopped and resume after Auto refresh is completed.
z Fan Life (Applied only to Environmental models) :Enables setting the Fan Life.
- Message Display: Two months before pan life termination (1440 hours), the following warning
message will appear. “Fan Life Expired. Replace the Fans”
f ON: Display the warning message. (Default)
f OFF: Do not display the warning message.
Ú [OFF] is to hide the message, rather than to delete it. Set it back to [ON]. Then, the warning
message will appear. (Only if you didn’t clear the message [Message Clear])
- Message Clear: Use this if you want to delete the warning message when it pops up.
Ú If you set [Message clear] to [On]after performing the command, no warning message will appear
on the screen.
- Time Reset: Set to count the fan life again after replacing the fan. (However, this is available only
after you see a warning message that the fan life has expired.)
Ú The fan life is counted only for an actual operation so the fan can be used longer than the
displayed time.
- Time Remain.(hour):
f 49000 : Remaining life of fan (unit: hour)
f The fan life will be updated when you access the [Fan Life] menu and if you press [ENTER] on the
[Time Remain.(hour)] item.
English - 79
setup
PASSWORD SETTING
The Password feature enables you to configure a password for
rebooting the camera and accessing the OSD and preventing
unauthorized modification of existing camera settings.
z On/Off :
Enables or disables Password protection.
z Edit Password
Change the password; enter the current password and then a
new one, consisting of 4 hexadecimal characters (0~F).
 The default password is "0000".
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Password Setting
On/Off
Edit Password
OFF
STATUS
Displays the settings and version of the camera.
z MODEL :
Indicates the model name of the camera.
z CAM VER. :
Indicates the software version of the camera.
z DOME VER. :
Indicates the version of the camera control board.
z COAX VER. :
Indicates the software version of the Coax communication
z PROTOCOL :
Indicates the status of the current protocol.
z DOME ID :
Dome Camera ID
z CONTROLLER :
Indicates the settings of the current communications mode.
80_ setup
Main Menu
Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Password Setting
Status
Æ
Camera Status
MODEL
CAM VER.
DOME VER.
COAX VER.
PROTOCOL
DOME ID
CONTROLLER
= SCP-2371N
= VX. XX_YYMMDD
= VX. XX_YYMMDD
= VX. XX_YYMMDD
= AUTO DET.
= 001
= Simplex
troubleshooting
TROUBLESHOOTING
If the product does not function properly, please see the below for trouble shooting.
Problem
Cause and Solution
Page
14~16
► Verify the setups of ID, protocol, and baud rates.
17~28
► Check if power cable is securely connected to the camera and the monitor.
Check if the video cable is properly connected. Consult the operation
manual of the system controller connected to the camera.
14~16
► Check if the iris of the lens is closed.
Adjust the menu for the iris of the lens.
47
► Check the camera’s fixed shutter speed.
Adjust the camera’s shutter menu.
47
The picture is too dark/bright.
► Check the camera’s Brightness menu.
Adjust the camera’s Brightness menu.
47
The monitor displays a white
image.
► Check if the iris of the lens is open.
Adjust the menu for the iris of the lens.
47
► Check if the dome cover or the camera lens is dirty or smudged.
If it is, clean the dirt off.
-
► Verify the distance between the camera and the subject, as well as the
subject’s surroundings. Camera may have difficulty focusing on a subject
against a white background.
-
► If Auto Focusing is having difficulty focusing on a particular subject, set
Focus Mode to Manual and adjust the focus by yourself.
45
► Use the camera’s reset menu to restore the camera settings in order to
default.
79
► Adjust Sharpness level.
54
► Check if the video cable is properly connected.
-
► Make sure that the power cable and video cable do not exceed the
recommended maximum lengths.
29
► Adjust Sharpness level.
54
No picture is displayed on
monitor.
Picture is out of focus.
Digital noise appears in picture.
English - 81
● TROUBLESHOOTING
► Check if the camera and peripheral devices are properly connected.
Controller does not work.
troubleshooting
Problem
Cause and Solution
Page
► Check the White Balance.
46
► Adjust Color Menu in Image Adj.
54
► Check if the dome cover or the camera lens is dirty or smudged.
If it is, clean the dirt off.
-
The picture is flickering.
► Check if the camera is pointing directly at a fluorescent light or sunlight. If
so, change the camera’s direction to remove the flickering.
-
Afterimages appear in picture.
► Check Sens-Up settings.
47
Camera switches between color
and B&W modes frequently.
► Adjust Duration and Dwell Time in Day & Night menu.
53
► Check if power cable is securely connected to the camera and the monitor.
Check if the video cable is properly connected.
Consult the operation manual of the system controller connected to the
camera.
14~16
► Check if Pan Limit and/or Tilt Limit are set.
If so, remove the limit(s).
67
► A motor or the lens may be overheated.
If so, contact your service personnel or system provider for assistance.
-
► This phenomenon may happen, since the motors have a margin error of ±0.1˚.
-
Picture’s colors are not good.
Pan, tilt, zoom, and/or focus do
not work.
The camera’s position differs
from the position defined in a
preset.
Sequence configuration of the
camera does not work.
The upper side of the picture is
dark when the camera is on the
horizontal reference point.
Camera suddenly turns on or
moves to a preset position by
itself.
82_ troubleshooting
► Check if Preset or another operation mode has been set.
► Check the Auto Refresh settings.
55~66
► You are seeing the camera's internal cover. The camera is functioning
normally.
-
► Check the Auto Run settings.
Auto Run puts a camera through a predefined action sequence if the user
does not use the Controller to operate the camera for a certain period of
time.
65
► Check the Auto Refresh settings.
Auto Refresh optimizes the camera's circuitry and components according
to a predefined schedule.
79
Problem
Coxial communication does not
work.
I can’t see the screen.
(The screen is black.)
The camera stops in the Initialize
mode and won’t proceed to the
next mode.
I can use the controller, but I
can’t activate the Sequence
command.
I can't get rid of this message
from the screen: “ Fan life
Expired. Replace the Fans.”
Page
► Check the distance between the camera and the monitor.
29
► If the distance between the camera and the monitor exceeds the
recommended maximum, please use an auxiliary video amp.
29
► Ensure that the Camera ID DIP switches (SW1) are all positioned to OFF.
17
► Please check the environment temperature; the camera may not operate
properly if it has been left at temperatures lower than -50º for a prolonged
duration.
7
► The motor may malfunction at temperatures lower than -20º; please turn
on the camera in Standby mode instead of [Initialize].
7
► When the internal temperature is above -20°C at the time power is
supplied, the “Wait to warm up (xx Left)” message will disappear and the
product will enter normal operation state upon rebooting. The sequencing
operation will be restricted, allowing only manual P/T operation.
7
► When the camera’s internal temperature drops down to -20º or lower, it
becomes unable to transmit video signals and may cause a black screen.
7
► A black screen does not indicate camera breakage; it resets itself and
starts displaying video again once its internal temperature reaches -20º or
higher.
7
► The motor may malfunction at temperatures lower than -20º ; please turn
on the camera in Standby mode instead of [Initialize].
7
► When the camera's internal temperature is between -10º to -20º, the
motor may malfunction, limiting the use of the Sequence and Turbo
commands.
7
► Once the internal temperature reaches -10º or higher, all Sequence modes
become reactivated normally.
7
► Please make sure to "Clear" the message from the screen.
7
► Such symptoms may occur if the camera's temperature increases from
-20º or lower to -20º or higher.
7
The camera suddenly resets
itself while displaying the black
screen.
English - 83
● TROUBLESHOOTING
I turned on the power, but the
camera didn't start running.
(SCP-XXXXH Only)
Cause and Solution
troubleshooting
Problem
Cause and Solution
Page
"Auto Refresh(Wait)" appears
and the camera reboots.
► Such symptoms may occur if the camera's temperature increases from
-10º or lower to -10º or higher to prevent the malfunction of motor.
7
“Please Check Heater System”
appears.
► The heater may malfunction. Turn off the camera and call where you
bought.
7
Check the Power cord’s by periods
y The Power cord’s coating has
been damaged.
y The power cord is hot to touch
when the product is in operation.
y The power cord gets hot after
being folded or pulled on.
84_ troubleshooting
Continuing to use the product when its power cord is damaged constitutes an
electrical and fire hazard. The power plug must be removed from the outlet
immediately, and a qualified service personnel or your system provider should be
contacted for assistance.
-
product specifications
PRODUCT SPECIFICATIONS (SCP-2XX1 SERIES)
Model
Image Device
Effective Pixels
SCP-2371/2271
1/4” Super HAD CCD II
NTSC : 811(H) x 508(V)
PAL : 795(H) x 596(V)
NTSC : 768(H) x 494(V)
PAL :752(H) x 582(V)
Scanning System
2:1 Interlace
Synchronization
Internal / Line Lock
Frequency
Horizontal Resolution
Min. Illumination
S / N Ratio
NTSC : H : 15.734kHz / V : 59.94Hz
PAL : H : 15.625KHz / V : 50Hz
Color : 600TV lines / BW : 700TV lines
COLOR : 0.2 Lux (50 IRE @ F1.6 ), 0.0004 Lux (50IRE, Color, Sens-up 512x )
B/W : 0.02 Lux (50 IRE @ F1.6 ), 0.00004 Lux (50IRE, B/W, Sens-up 512x )
52 dB (AGC off, Weight On)
Video Output
CVBS : 1.0 Vp-p / 75Ω conposite
Focal Length
(Zoom Ratio)
3.5~129.5mm (37x) / 3.5~94.5mm (27x)
Max. Aperture Ratio
1:1.6 (Wide) ~ 3.9 (Tele) (37x)/1:1.6 (Wide) ~ 2.9 (Tele) (27x)
Angular Field of View
H : 55.5°(Wide) ~ 1.59°(Tele) / V : 42.5°(Wide) ~ 1.19°(Tele) (37x)
H : 55.5°(Wide) ~ 2.24°(Tele) / V : 42.5°(Wide) ~ 1.79°(Tele) (27x)
Min. Object Distance
1800mm
Focus Control
AUTO / MANUAL / ONE SHOT
Pan Range
360° Endless
Pan Speed
Preset : 500°/sec / Manual : 0.024°/sec ~ 120°/sec
Tilt Range
-5° ~ 185°(-15° ~ 195° possible)
Tilt Speed
Preset : 500°/sec / Manual : 0.024°/sec ~ 120°/sec
Preset
Preset Accuracy
OSD
● PRODUCT SPECIFICATIONS
Total Pixels
SCP-2371H/2271H
255
±0.1°
NTSC: ENGLISH, FRENCH, SPANISH, PORTUGUES, KOREAN, JAPANESE, TAIWANESE
PAL: ENGLISH, CHINESE, FRENCH, GERMAN, SPANISH, ITALIAN, PORTUGUES, POLISH, RUSIAN, CZECH,
TURKISH
Camera Title
Off / On (Displayed 12 Characters)
Day & Night
Auto (ICR) / Color / B/W
Back Light
BLC / HLC / Off
English - 85
product specifications
Model
SCP-2371H/2271H
SCP-2371/2271
Contrast
Enhancement
SSDR (Off/On)
Digital Noise
Reduction
SSNR III (Off/On)
Digital Image
Stabilization
Off/On
Motion Detection
Off/On
Privacy Masking
Off/On (8 programmable zones)
Sens-up
2x ~ 512x
Gain Control
Off/Low/Medium/High/Manual
White Balance
ATW / ATW (IN) / ATW (OUT) / Manual / AWC
NTSC :1/60~1/120,000sec
Electronic Shutter
Speed
PAL : 1/50~1/120,000sec
Digital Zoom
Off/On (2x ~ 16x)
Digital Flip
Off/On
Schedule
Day/Time
Alarm
8 In 3 Out
Communication
Protocol
RS-485/422, Coaxial Control
Coax : Pelco-C ( Coaxitron )
RS-485: Auto Detected, SAMSUNG-T, SAMSUNG-E, Pelco(D/P), Panasonic, Vicon,Honeywell,AD,GE,BOSCH
Operating Temperature
/ Humidity
Ingress Protection
-50°C ~ +55°C / Less than 90% RH
-10°C~+55°C / Less than 90% RH
IP66
-
Input Voltage
24V AC ±10%
Power Consumption
Max. 15W / 60W (Fan & Heater)
Max. 15W
Color / Material
Ivory, Aluminum, Plastic ( Dome Cover : Clear )
Ivory, Plastic (Dome Cover : Clear)
Dimension (Φ×H)
Ø220.0 x H293.6 mm
Ø152.0 x H218.0 mm
3.1Kg
1.6Kg
Weight
Ú The specification for this product may change without prior notice for product improvement.
86_ product specifications
PRODUCT SPECIFICATIONS (SCP-3371 SERIES)
Model
Image Device
Effective Pixels
SCP-3371
EX-view HAD CCD
NTSC : 811(H) x 508(V)
PAL : 795(H) x 596(V)
NTSC : 768(H) x 494(V)
PAL :752(H) x 582(V)
Scanning System
2:1 Interlace
Synchronization
Internal / Line Lock
Frequency
Horizontal Resolution
Min. Illumination
S / N Ratio
NTSC : H : 15.734kHz / V : 59.94Hz
PAL : H : 15.625KHz / V : 50Hz
Color : 600TV lines / BW : 700TV lines
COLOR : 0.7 Lux (50 IRE @ F1.6 ), 0.001 Lux (50IRE, Color, Sens-up 512x )
B/W : 0.07 Lux (50 IRE @ F1.6 ), 0.0001 Lux (50IRE, B/W, Sens-up 512x )
52 dB (AGC off, Weight On)
Video Output
CVBS : 1.0 Vp-p / 75Ω conposite
Focal Length
(Zoom Ratio)
3.5~129.5mm
Max. Aperture Ratio
1:1.6 (Wide) ~ 3.9 (Tele)
Angular Field of View
H : 55.5°(Wide) ~ 1.59°(Tele) / V : 42.5°(Wide) ~ 1.19°(Tele)
Min. Object Distance
1800mm
Focus Control
AUTO / MANUAL / ONE SHOT
Pan Range
360° Endless
Pan Speed
Preset : 500°/sec / Manual : 0.024°/sec ~ 120°/sec
Tilt Range
-5° ~ 185°(-15° ~ 195° possible)
Tilt Speed
Preset : 500°/sec / Manual : 0.024°/sec ~ 120°/sec
Preset
Preset Accuracy
OSD
255
±0.1°
NTSC: ENGLISH, FRENCH, SPANISH, PORTUGUES, KOREAN, JAPANESE, TAIWANESE
PAL: ENGLISH, CHINESE, FRENCH, GERMAN, SPANISH, ITALIAN, PORTUGUES, POLISH, RUSIAN, CZECH,
TURKISH
Camera Title
Off / On (Displayed 12 Characters)
Day & Night
Auto (ICR) / Color / B/W
Back Light
WDR
● PRODUCT SPECIFICATIONS
Total Pixels
SCP-3371H
BLC / HLC / Off
Low / Medium / High
English - 87
product specifications
Model
SCP-3371H
SCP-3371
Contrast
Enhancement
SSDR (Off/On)
Digital Noise
Reduction
SSNR III (Off/On)
Digital Image
Stabilization
Off/On
Motion Detection
Off/On
Privacy Masking
Off/On (8 programmable zones)
Sens-up
2x ~ 512x
Gain Control
Off/Low/Medium/High/Manual
White Balance
ATW / ATW (IN) / ATW (OUT) / Manual / AWC
NTSC :1/60~1/120,000sec
Electronic Shutter
Speed
PAL : 1/50~1/120,000sec
Digital Zoom
Off/On (2x ~ 16x)
Digital Flip
Off/On
VPS
Off/On
Intelligent Video
Off / Detection / Tracking / Fixed/Moved
PIP
Off/On
Schedule
Day/Time
Alarm
8 In 3 Out
Communication
Protocol
RS-485/422, Coaxial Control
Coax : Pelco-C ( Coaxitron )
RS-485: Auto Detected, SAMSUNG-T, SAMSUNG-E, Pelco(D/P), Panasonic, Vicon, Honeywell, AD,
GE, BOSCH
Operating Temperature
/ Humidity
Ingress Protection
-50°C ~ +55°C / Less than 90% RH
-10°C~+55°C / Less than 90% RH
IP66
-
Input Voltage
24V AC ±10%
Power Consumption
Max. 15W / 60W (Fan & Heater)
Max. 15W
Color / Material
Ivory, Aluminum, Plastic ( Dome Cover : Clear )
Ivory, Plastic (Dome Cover : Clear)
Dimension (Φ×H)
Ø220.0 x H293.6 mm
Ø152.0 x H218.0 mm
3.1Kg
1.6Kg
Weight
Ú The specification for this product may change without prior notice for product improvement.
88_ product specifications
DIMENSIONS
❖ Indoor Model
Unit: mm (Inches)
● PRODUCT SPECIFICATIONS
Ø152(5.98)
Ø133.2(5.24)
English - 89
product specifications
❖ Environmental Model
Unit: mm (Inches)
1-1/2 inch PF TAP
[Diameter (max) = 47.803mm, Pitch=2.3091mm]
Ø220(8.66)
90_ product specifications
MEMO
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60, FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300, FAX : +44-1932-45-5325
PT01-001617A