advertisement
SETU ATA211G
System Manual
SETU ATA211G
VoIP-FXS-GSM Adaptor
System Manual
Documentation Disclaimer
Matrix Comsec reserves the right to change, at any time, without prior notice, the product design, specifications, components, as engineering and manufacturing may warrant.
This is a general documentation for all models/configurations of the product. The product may not support some of the features/facilities described in this document.
While every reasonable effort has been made to ensure accuracy of content in this document, Matrix Comsec assumes no responsibility for errors or omissions that may occur herein. No liability is assumed for damages, costs, expenses resulting from unauthorized modifications or repairs to the product; failure to use information or to comply with the installation, operation and maintenance instructions contained in this document .
Copyright
All rights reserved. No part of this system manual may be copied or reproduced in any form or by any means without the prior written consent of Matrix Comsec.
Version 2
Release date: February 3, 2011
Contents
Table of Contents v
vi Table of Contents
CHAPTER 1
Introduction
Welcome
Thank You for choosing SETU ATA211G! This product is designed to give you the highest performance, combined with real ease of use. We hope you will make the optimum use of intelligent, intuitive, feature-packed VoIP Phone
Adapter. We recommend you to read this document carefully to get acquainted with the product before installing and operating it.
About this System Manual
This document contains detailed information and instructions for installing, configuring, and operating SETU
ATA211G. It also contains information on maintenance and safety instructions.
Intended Audience
This manual is aimed at:
• Network Administrators and System Engineers, who will install, maintain and support SETU ATA211G.
It is assumed that they have some experience in installing VoIP - GSM Gateways and are familiar with
VoIP technology.
• End Users, persons/organizations who will use SETU ATA211G. They include home users, personnel of small and medium businesses, large enterprises, other commercial and public organizations/ institutions.
Organization of this document
This System Manual contains following topics:
• Introduction: Gives information about this System Manual.
• Know Your SETU ATA211G: Provides overview of SETU ATA211G.
• Getting Started: Contains information on how to install SETU ATA211G, how to configure the device using the web-based programming tool, Jeeves, and using the phone connected to the device.
• Configuring Basic Settings: Provides instructions for configuring the basic parameters of SETU
ATA211G, which are sufficient to get the system into operation.
Matrix SETU ATA211G System Manual 1
2
• Configuring Advance Settings: Contains instructions for configuring the more advanced features and facilities of SETU ATA211G.
• Features of SETU ATA211G: Describes in detail, the features of SETU ATA211G, along with instructions for configuring and using these features.
• System Status: Displays the status indicators of system parameters like SIP, Mobile, Network (LAN and
WAN), etc and details of the System Firmware.
How to Read this System Manual
This System Manual is organized in a manner to help you get familiar with SETU ATA211G, learn how to install it, how to connect it to the IP network, how to configure the Basic Settings that allow you to start making and receiving calls, and move on to the Advanced configuration to use the special features and functions. You may read it in the sequence it is organized. .
Conventions used in this System Manual
Instructions
The instructions in this document are written in a step-by-step format. Each step, its result, indication/notification, where and as it occurs, has been described.
Notices
The following symbols have been used for notices to draw your attention to important items.
Important: to indicate something that requires your special attention or to remind you of something you might need to do when you are using the system.
Tip: To indicate a helpful hint giving you an alternative way to operate the system or carry out a procedure, or use a feature more efficiently.
Cross-references
Cross references are given in blue font and hyperlinked. You may click on the hyperlinked text to reach the source of the cross-reference.
Terminology
The technical terms and Acronyms used in this manual are standard terms, commonly used in the telecommunications and data communications industry. Considering the broad group of intended users of this manual, wherever possible, use of jargon is avoided.
Acronyms have been defined in the text and a complete list of Acronyms used in this document is provided in the
Appendix.
The words ATA, ATA211G, SETU ATA211G and System means SETU ATA211G.
Matrix SETU ATA211G System Manual
Some of the terms specific to this manual that you will encounter frequently are defined below:
Term
Admin
User
Caller/Calling Party
Callee/Called Party
Transferor
Transferee
Transfer Target
LAN Administrator
Usage in the document
A person who install, configure and maintains SETU ATA211G. Admin can also be the user.
Admin has full accessibility of the system.
A person who uses SETU ATA211G. User has limited access to the system.
A person who makes calls.
A person who receives the calls.
A person who transfers the calls.
The remote user whose call is to be transferred (first party) to another remote user
(second party)
The remote user to whom the call is to be transferred (second party) .
A person who maintains the LAN network of an organization.
Using this manual, you will be able to install, operate and make optimum use of SETU ATA211G. If you encounter any technical problems, please contact your Dealer/reseller or Matrix for support.
Matrix SETU ATA211G System Manual 3
4 Matrix SETU ATA211G System Manual
CHAPTER 2
Know Your SETU ATA211G
Overview
ATA211G is a VoIP Analog Telephone Adapter used as a SIP-FXS-Mobile gateway. It allows you to make and receive voice calls over IP Network as well as PSTN network using conventional telephone instrument.
ATA211G can be used in Residence, SOHO, Corporate Offices, Industries, Workshops, etc. ATA211G can be used to make voice calls to remotely located branch offices of an enterprise using Internet network.
ATA211G also offers flexibility to make VoIP calls over the internet and browse the Internet simultaneously using inbuilt router.
ATA211G uses SIP (Session Initiation Protocol) protocol to make voice calls over the IP network. ATA211G converts the voice traffic into IP packets for transmission over the internet. When a telephone number is dialed by you, ATA211G converts it into an IP call using the Session Initiation Protocol (SIP) and initiates a call, thereby making VoIP calls as easy as normal telephone call. You have flexibility to make a call by selecting any SIP trunk or you can also select Mobile port to make a call.
The number dialed from FXS port can be routed to Mobile port or SIP trunk based on the number dialed. The
Incoming call on SIP can be routed to FXS or Mobile Port or to a fixed destination number based on the CLI received. The Incoming call on the Mobile port can be routed to FXS port or SIP trunk as configured in Dialed
Number Table.
ATA211G has three voice ports, viz. FXS, SIP and Mobile.
ATA211G has 1 WAN Port, 1 LAN Port, 1 FXS Port, 1 Mobile Port, an antenna connector, a power socket, and 5
LEDs as shown in below figure.
Matrix SETU ATA211G System Manual 5
Ports and Connectors
Port Name
12V DC
LAN
WAN
FXS
SIM
Antenna
Connector
DC Jack
RJ45
RJ45
RJ11
SIM holder
SMA (Male)
Description
Power Adapter
To connect a standalone computer or a LAN Swtich.
To connect to the IP network over a DSL Modem or Router or a LAN Swtich
To connect a standard telephone instrument or a PBX.
To connect to GSM network.
To connect Mobile port antenna.
LED
SETU ATA211G has an LED each for the FXS port, the Mobile port, the SIP Trunks (SIP1, SIP2) and POWER, to indicate the status of the ports, and various events occurring on the ports, including errors.
6 Matrix SETU ATA211G System Manual
SIM
SIM
ANTENNA
Matrix SETU ATA211G System Manual 7
8
Applications of SETU ATA211G
1.
Residential Application: Home users can use ATA211G to make low-cost international calls to family, friends and relatives.
IP Network
FXS
Proxy
Broadband
Modem/Router
Mobile
GSM
Network
ATA211G
LAN
2.
SOHO Application: Small Office owners can use ATA211G to make low-cost calls to their overseas customers, employees, suppliers, etc.
IP Network
FXS
Proxy
Broadband
Modem/Router
Mobile
GSM
Network
ATA211G
LAN
Matrix SETU ATA211G System Manual
3.
Business Application: Corporate Offices can use ATA211G to make low-cost international calls to their overseas customers, employees, suppliers, etc.
Switch
IP Network
Proxy
FXS1
Broadband
Modem/Router
WAN
Mobile
GSM
Network
ATA211G
LAN
PBX
4.
Peer-to-Peer Call Application: Corporate Offices also use SETU ATA211G to communicate between various branch offices, at no cost.
FXS
LAN
Location D
ATA211G
WAN
Broadband
Modem/Router
Location A
WAN
ATA211G
FXS
LAN
FXS
LAN
Location C
ATA211G
WAN
IP Network
Broadband
Modem/Router
Location B
WAN
ATA211G
FXS
LAN
Matrix SETU ATA211G System Manual 9
10 Matrix SETU ATA211G System Manual
CHAPTER 3
Getting Started
Preparing for Installation
Package Contents
SETU ATA211G with Antenna
Adaptor 12V, 1.25 Amp
(Country Specific)
Quick Start and User Card Ethernet Cable (RJ45)
CD containing System Manual,
Quick Start and User Card
Two Screws M 7/30
Two Screw Grips
Warranty Card Set
External Antenna SMA with Cable
• Unpack SETU ATA211G.
• Verify the package contents. Contact your vendor/Service Provider/administrator, if any of the above listed items is missing or damaged.
Protecting SETU ATA211G and yourself
You are recommended to take the following measures to protect yourself and SETU ATA211G.
Installation Precautions
Do not install the system in a place where,
• it may be exposed to direct sunlight, excessive cold or humidity.
• it may be exposed to dust, water, oil, corrosive fumes.
• it may fall, causing damage to the product.
• shocks or vibrations are frequent or strong.
• there is a water source or body, like a wash basin/kitchen sink, bath-tub, a swimming pool, sprinkler, etc.
Make sure there is enough open space for ventilation at the site of installation.
Matrix SETU ATA211G System Manual 11
Safety Instructions
Take every measure to reduce the risk of fire, electric shock and injury to the person handling this product.
• Read all the instructions given in this manual.
• Always switch off the product, unplug the product from the wall outlet when handling it. Removing covers or opening the system or incorrect reassembly increases the risk of electric shock.
• Never open the system in power ON condition.
• Use the adapter provided with the product.
• Make sure telephone cables not touch exposed power line cables.
• Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
• Unplug the product from the wall outlet before cleaning. Do not use liquid cleaners. Use only dry and soft cloth.
Always get your product serviced by a trained, qualified person. Contact your authorised dealer or Matrix support, if:
• liquid has been spilled into the product or the product has been exposed to rain or water.
• the product has been dropped or the cabinet has been damaged.
• the product does not operate normally or exhibits a distinct change in performance.
Warning for RF Safety
The product complies with RF exposure guidelines as per standard FCC 47 CFR part 2. We recommend the following precautions:
• Make sure that the RF Antenna is installed at least 20 cm away from other electronic and radio transmission devices.
• Make sure that the RF Antenna is installed atleast 20 cm away from people's vicinity.
• Do not place magnetic storage media near the product.
• People carrying medical implants like cardiac pacemakers are advised to maintain appropriate distance from the system. They are also advised to avoid being in the vicinity of the product for a long time.
• Do not place the magnetic storage media near the device.
• People carrying medical implants like cardiac pacemakers are advised to maintain appropriate distance from the system. They are also advised to avoid being in the vicinity of the product for a long time.
Mounting the SETU ATA211G
To mount SETU ATA211G on the wall,
• Select a suitable place.
• Use the mounting template provided to you to drill holes of appropriate size and distance.
• Fix the screw grips in the holes you drilled.
• Fix the screws in the holes, leaving the screw heads protruding a few millimeters from the wall.
• Check the strength of the screws.
• Mount SETU ATA211G on the wall.
12 Matrix SETU ATA211G System Manual
Connecting SETU ATA211G
Power
Adaptor
IP
PC/LAN
DSL Modem/
Router
• Connect a standalone computer/ LAN Switch to the LAN Port of SETU ATA211G using an Ethernet cable.
• Connect the WAN Port of SETU ATA211G to the IP Network - a DSL modem or Router or a LAN Switch - using the Ethernet cable provided to you.
• Connect a telephone to the FXS Port of SETU ATA211G, using a standard telephone cable with an RJ11 plug.
You may also connect a PBX to the FXS port of SETU ATA211G.
SIM
SIM
ANTENNA
• Screw the antenna on to the antenna connector.
Protecting the SIM Card
To protect the SIM card, before you insert the card in the system, do the following:
• Insert the SIM Card into a Mobile Handset.
• Enable SIM PIN protection.
• Change the SIM PIN to 1234 (default).
Matrix SETU ATA211G System Manual 13
• Remove the SIM Card from the Mobile Handset.
• Insert the SIM Card in to the SIM Holder of SETU ATA211G.
You may change the SIM PIN to the desired value after system installation is completed. You can change the SIM
PIN from Mobile Port parameters page of Jeeves. See
under Basic Settings for instructions.
• Insert SIM Card into the SIM holder of the Mobile Port of SETU ATA211G. To do this,
• press the SIM holder lock (the small yellow button). You may use a blunt pin to press the lock button.
• the SIM holder tray emerges from its slot.
• pull out SIM holder tray from its slot.
• now, fit the SIM Card on the tray, with its contact side facing up.
• insert the SIM holder tray back into the slot.
Press the yellow button to release the SIM holder.
Insert SIM with contact side facing up.
• Connect the power adapter provided with SETU ATA211G to the power jack labeled 12VDC-1A(MAX).
• Connect the adapter plug into a power outlet.
• Switch ON power.
• Wait for the Reset Cycle to complete.
Reset Cycle
• At Power ON,
• The Power LED will glow green continuously.
• All other LEDs - FXS, Mobile, SIP1 and SIP2 will glow Red for ms, where xxx time depends on the timing cycle from boot loader program to init sequence.
• After few seconds of Power ON, the Mobile LED starts blinking red. It indicates the network availability.
• On successful completion of initiation cycle, each LED will glow as per the events summarized in the table below:
Meaning of LEDs
LED
FXS
Status
ON
Blinks Fast
Blinks Slow
OFF
Meaning
IC Call/OG Call - Speech and Off hook
Error condition during IC/OG call
IC Call: Ring Event OR OG Call: Number being dialed (after the end of dialing)
FXS port ON-Hook
14 Matrix SETU ATA211G System Manual
LED Status
Mobile ON
Blinking (100 ms ON-100 ms
OFF)
SIP1
SIP2
Meaning
SIM Card is present and or registered with the network.
SIM Card is absent or de-activated or SIM PIN is faulty or SIM PUK is required
Blinking (1 ms ON - 1 ms OFF) SIM Card detected but is not registered with the network
OFF ATA211G is powered ON but SIM Card is not detected
ON
Blinks Fast
Blinks Slow
OFF
ON
Blinks Fast
SIP1 is enabled and is registered with the SIP server or 'Active' status of SIP Trunk.
SIP1 is enabled but not registered with the SIP server (SIP is configured as proxy).
SIP1 is enabled but not registered with the SIP server (SIP is configured for P2P calling).
SIP1 is disabled.
SIP2 is enabled and is registered with the SIP server or 'Active' status of SIP Trunk.
SIP2 is enabled but not registered with the SIP server (SIP is configured as proxy).
Blinks Slow
OFF
SIP2 is enabled but not registered with the SIP server (SIP is configured for P2P calling).
SIP2 is disabled.
You can also view the status of the ports on the Status page of the web-based graphical user interface of SETU
ATA211G.
Matrix SETU ATA211G System Manual 15
Configuring SETU ATA211G
SETU ATA211G provides access to system configuration at two levels: Admin and User. A distinct set of features and facilities can configured at each of these levels.
SETU ATA211G can be configured using its Web-based graphic user interface (GUI) and from the phone connected to its FXS port. While the entire system configuration can be done using the GUI, you can configure only certain parameters from the phone.
Admin Mode
Admin is defined as the person who installs, configures and maintains the SETU ATA211G. The Admin can also be the User. In the Admin mode, you have full access to system configuration, all configurable parameters, features and facilities, and system maintenance:
• Basic Settings
• Advanced Settings
• Supplementary Services
Access to Admin mode is protected by a password. The default Admin Password is 1234. The password may be changed.
User Mode
In the User mode, you can configure specific features and facilities of SETU ATA211G, as listed below:
• Supplementary Features
• Speed Dialing
• Network parameters
• User Password
• Syslog (debug)
• Factory Defaults
• PCAP
Access to the User mode is also protected by a password, referred to as the User Password. The default User
Password is 1234. The password may be changed.
Configuration using Web-based GUI: Jeeves
SETU ATA211G has a graphic user interface (GUI), Jeeves, an easy-to-use proprietary software of Matrix for system configuration. Jeeves is an embedded, web server which you can access from the computer you connected to the LAN Port or the WAN Port of SETU ATA211G.
Jeeves allows system configuration in the Admin mode and User mode.
To access Jeeves, follow these steps:
• Connect a standalone computer to the LAN port of SETU ATA211G. The LAN Port of SETU ATA211G and that of the computer must be in the same Subnet.
The default IP Address of the LAN port of SETU ATA211G is: 192.168.2.21
The default Subnet Mask of the LAN port of SETU ATA211G is: 255.255.255.0
16 Matrix SETU ATA211G System Manual
If required, change the IP Address and the Subnet of the computer.
You may also connect the LAN port of SETU ATA211G to a LAN switch. If you connect the LAN port of
SETU ATA211G to a LAN Switch, make sure that the IP Address of LAN port of SETU does not conflict with the IP Address of any device on the LAN, and SETU ATA211G is in the same Subnet as the LAN computer.
You may change the IP Address and Subnet Mask of the LAN Port of SETU ATA211G by dialing the
relevant System Commands from the phone connected to the FXS port of SETU ATA211G. See “” topic.
When installing the system for the first time, you are advised to connect SETU ATA211G to a standalone computer only.
• Make sure a web-browser, either Internet Explorer 7 or Mozilla Firefox, is installed on the computer.
• Open the browser on the computer.
• Type 192.168.2.21, the default IP address of the LAN port of SETU ATA211G, in the address bar of the browser and press Enter key/click Go.
If you have connected SETU ATA211G to the LAN and have changed the IP Address of the LAN port of
SETU ATA211G, enter the current IP Address in the address bar of the browser.
The Login page of Jeeves opens.
You can also use the WAN Port of SETU ATA211G to access the embedded web server in the same manner.
The default IP Address of the WAN Port of SETU ATA211G is: 192.168.1.196
The default Subnet Mask of the WAN Port of SETU ATA211G is: 255.255.255.0
On the Login page of Jeeves, you are offered two Login modes: Admin and User.
To log in as Admin,
Matrix SETU ATA211G System Manual 17
• In the Login as combo box, select Admin.
• In the Password field, enter 1234, the default Admin Password.
• Click the Login button.
• On successful login, the Admin mode page will open.
• The left pane shows the links Basic Settings, Advanced Settings, Supplementary Services, and
Status.
Basic Settings are sufficient to get your SETU ATA211G into operation.
• Click the links to expand.
To log in as User,
18
• In the Login as combo box, select User.
• In the Password field, enter 1234, the default User Password.
• Click the Login button.
• On successful login, the User mode page will open.
• The left pane displays User Settings and Status links.
• Click the User Settings link to expand. The sub-links to the functions and features that are allowed to be configured from the User mode appear on the left pane: Supplementary Features, Speed
Dialing, Network, User Password, Syslog, Factory Defaults and PCAP.
• Click the Status link to view the status of the system and the ports.
Matrix SETU ATA211G System Manual
Configuring using a Phone
You can enter the Admin mode and the User mode using the phone connected to the FXS Port of SETU
ATA211G, and change feature settings, and certain network parameters like the IP Address and Subnet Mask of the LAN and the WAN port of SETU ATA211G, select the Connection Type (IP Addressing) by dialing
Commands” from the phone connected to its FXS port of SETU ATA211G.
You can also dial System Commands to view the current IP Addresses of the WAN and LAN Ports (if your phone has a display).
Follow the instructions given below to configure the system from the phone.
Admin Mode
• Lift the receiver of the phone.
• Dial #19 to enter the Admin mode.
• Dial the Admin Password (default: 1234).
You will get programming tone.
• Dial the System Command for the feature/facility you want to configure.
For example:
To change IP Address of the LAN Port, dial 12<LAN IP Address>#* .
For example, to change the IP address to to 192.168.2.21, dial 12192168002021#*
• When you dial a valid command, SETU ATA211G plays a confirmation tone for 3 seconds, and plays the programming tone.
• Dial 0 to exit configuration mode.
When network parameters are changed, SETU ATA211G will restart, without dial tone/confirmation tone.
You can also view the Network parameters (IP Address, Subnet Mask, Connection Type. etc.) on the phone’s display. See
.
For a complete list of commands, refer “System Commands”
in the Appendix.
User Mode
• Lift the receiver of the phone.
• Dial #18 to enter the User mode.
• Dial the User Password (default: 1234).
• You will get programming tone.
• Dial the command for the feature/facility you want to configure.
For example,
The command for configuring the destination number for Call Forward -Unconditional is: 51-Destination
Number-#*
To configure 2001 as the destination number for Call Forward-Unconditional, dial 512001#*
• Dial 0 to exit programming mode.
For a complete list of commands, refer “System Commands”
in the Appendix.
Matrix SETU ATA211G System Manual 19
20 Matrix SETU ATA211G System Manual
CHAPTER 4
Configuring Basic Settings
The Basic Settings enable you to configure SETU ATA211G for basic functions. As Basic Settings cover much of your configuration requirements, you will be able to operate and use the system efficiently, when you configure
Basic Settings.
To configure Basic Settings,
• Click Basic Settings link.
The links to the different basic parameters appear on the left pane.
There are two ways to configure Basic Settings:
• Using the Wizard. The Wizard will guide you step-by-step through the configuration.
OR
• Selectively configuring the Basic Settings parameters, by clicking the links on the left pane.
Matrix SETU ATA211G System Manual 21
To use the Wizard,
• Click the Wizard icon on the top right of your screen.
• The Next button takes you to the next page, saving the changes you made on the current page.
• The Back button returns you to the previous page.
• The More
• The Less button expands parameters on the page.
button collapses parameters on the page.
• The Quit button allows you to exit the Wizard at any stage, saving changes you made before exiting.
To use selective configuration,
• Click Basic Settings link to expand.
• Click each parameter link, Region, SIP, Mobile, FXS, Passwords, Network.
• The selected parameter page opens.
• The More button expands parameters on the page.
• The Less button collapses parameters on the page
• Set the desired values on the page.
• Click Submit to save your settings on the page.
You may use the Wizard or selectively configure the Basic Settings pages, whichever works best for you.
The instructions provided in this chapter, describe selective configuration of the Basic Settings pages.
1.
Click Basic Settings to expand.
2.
The following links appear under Basic Settings:
• Region
• SIP
• Mobile
• FXS
• Passwords
• Network
Each of these are explained in detail in the following.
22 Matrix SETU ATA211G System Manual
Region
1.
Click Region.
2.
Click More button to view all parameters on the page.
3.
Select Admin Language and User Language. Default: English.
SETU ATA211G can display the Admin and User pages of the GUI, Jeeves, in the following languages:
• English
• Italian
• Spanish
• French
• German
• Portuguese
All the Admin and User Pages of the GUI will appear in the language you selected, when you login again as Admin or User.
You can also select a Language on the Login page; however, it will be applied for the current session only.
4.
Select CPTG (Call Progress Tone Generation) to match the CPTG of the country where SETU ATA211G is installed. Default: India.
The ATA211G supports country specific Call Progress Tones Generation (CPTG) to simulate the same tones of the local PSTN to which it is connected. The CPTG supported by SETU ATA211G for different
countries are presented in the “Appendix”
.
When you reset SETU ATA211G to factory defaults, CPTG you selected will not be set to default.
5.
Select Ring cadence to match the ring cadence of the country where SETU ATA211G is installed. Select your country from the drop down list. Default: India.
During an incoming call, SETU ATA211G will play the ring over the SLT as per the Ring Cadence of the country you selected. For a complete list of Ring Cadences of different countries supported by SETU
ATA211G, see
Matrix SETU ATA211G System Manual 23
When you reset SETU ATA211G to factory defaults, the Ring you selected will not be set to default.
6.
To synchronize Date and Time of SETU ATA211G with that of the country where it is installed, select Time
Zone from the drop down list. Default: (GMT+05:30) Kolkata, Chennai, Mumbai, New Delhi.
7.
To use a public internet time server for date and time synchronization, select an internet based time server as NTP Server. You may select any of the three reliable public internet time servers
1
supported by SETU
ATA211G:
• ntp1.cs.wisc.edu
• time.windows.com
• time.nist.gov
Default: Ntp1.cs.wisc.edu
If you want to use an NTP server other than these, select the radio button and enter the IP Address/ domain of the server in the empty field.
When you reset SETU ATA211G to factory defaults, Date and Time settings will not be set to default.
8.
Click Submit to save your region settings.
1. You can select from three free, reliable public internet time servers run by the University of Wisconsin-Madison, Microsoft, and the
National Institute of Standards and Technology (NIST), to obtain date and time. You can also configure an NTP time server of your preference, other than these. These public internet time servers provide time offset from the Greenwich Mean Time (GMT), and you can select the time according to the time zone of the country you are installing the SETU ATA211G. For instance, if your ATA211G is installed in India, you can select the time zone for India (GMT+5.30 Calcutta, Chennai, Mumbai, and New Delhi). The time for India is offset from GMT by +5.30 hours. Similarly, if your ATA211G is installed in Hawaii, select the time zone for Hawaii, which is offset by
GMT -10:00 hours, to set the correct time and date.
24 Matrix SETU ATA211G System Manual
SIP Trunks
SETU ATA211G supports three SIP trunks, which may be configured as Proxy or Non-Proxy, i.e. Peer-to-Peer trunks. You may register with three different ITSPs and use their services.
1.
Click the SIP link.
The parameters of SIP Trunk 1 appear on your screen.
2.
Click More button to view all parameters of SIP Trunk 1 on this page.
Matrix SETU ATA211G System Manual 25
Trunk Settings
1.
Select the SIP Trunk Enable check box to use the SIP Trunk. Default: Disabled.
You may disable the SIP trunk, if you do not want to include it in Call Routing.
2.
Select SIP Trunk Mode according to your installation. Default: Peer-to-Peer.
• Select Proxy, if you want to register this SIP trunk with an ITSP or a Registrar Server.
• Select Peer-to-Peer, if you want to use the trunk for Peer-to-Peer (non-proxy) calls.
If you select Peer-to-Peer, you must also configure the number strings in the Peer-to-Peer Table.
• Click the arrow icon.
26 Matrix SETU ATA211G System Manual
• The Peer-to-Peer Numbers table opens in a new window.
• You can configure as many as 500 number strings, which are stored against an Index number.
• In the Number field, enter the peer-to-peer number string - prefix or entire number - that will be dialed. The number string must not exceed 24 characters. Default: Blank.
If the number to be dialed out is <dialednumber@destination address>, for example,
[email protected], you must enter 1234 in this field.
• To identify the number string you configured, enter a name in the Name field. It may be the name of your contact or any name you wish to assign to the number string. The name may consist of 24 characters (maximum). Default: Blank.
• As Minimum Digits, define the minimum length of the number string that must be dialed for the system to consider it as a valid number. Default: 01.
If the peer-to-peer number string you dial is shorter than the Minimum Digits you have configured, the system will not dial out the number.
• As Maximum Digits, define the maximum length of the number string that must be dialed out for the system to consider it the complete number string. Default: 24.
If the peer-to-peer number string you dial is longer than the Maximum Digits you have configured, the system will strip off the additional digits and dial out the number.
• In the Destination Address field, enter the domain name or IP Address to where the dialed peerto-peer number string is to be sent. The Destination Address may consists of up to 40 characters.
Default: Blank.
Matrix SETU ATA211G System Manual 27
28
For example, if the peer-to-peer number to be dialed out is [email protected], enter abc.com as
Destination Address. If the number is 1234@ 192.168.1.197, enter 192.168.1.197 as the
Destination Address. The Destination Address can also be in the form of Address:Port number.
• Click Submit to save entries.
• Close the window.
3.
Enter the SIP ID. This is the ID which remote parties will use to call this SIP Trunk. Default: Blank.
The SIP ID may be a number or text consisting of a maximum of 40 characters.
If you have defined the trunk mode as Proxy, enter the SIP ID provided by your ITSP. For example, if SIP
URI provided by the ITSP is [email protected], enter 12345 in this field.
If you have defined the trunk mode as Peer-to-Peer, enter the desired SIP ID.
4.
Enter Authentication ID. Default: Blank.
If you have defined the SIP trunk mode as Proxy, enter the Authentication ID (User ID) provided by your
ITSP.
If you have defined the trunk mode as Peer-to-Peer, enter the ID of your preference as Authentication ID.
5.
Enter Authentication Password. Default: Blank.
If you have defined the SIP trunk mode as Proxy, enter the Authentication Password provided by your
ITSP.
If you have defined the trunk mode as Peer-to-Peer, enter a password of your preference as Authentication
Password.
6.
SIP Registration is applicable for Proxy SIP Trunks only. Default: Disabled.
Select the check box to enable. SETU ATA211G will send the REGISTER message to Registrar proxy or
Outbound proxy as applicable.
7.
Select the OG Calls without Registration check box to allow the users to make outgoing calls irrespective of whether the SIP Trunk has been successfully registered with proxy or not.
By default, the system does not allow outgoing calls to be made if the status of the SIP trunk is 'not registered'.
8.
If you have defined the SIP trunk mode as Proxy, in the Registrar Server Address: Port field, enter the
Registrar Server Address and the Registrar Server’s listening port for SIP messages.
The registrar server address may be an IP address or a domain. Default: Blank.
The valid port range is: 1024-65534. Default: 5060.
9.
If your service provider uses an outbound proxy for handling voice calls, enable the Outbound Proxy check box.
Matrix SETU ATA211G System Manual
• In the Outbound Proxy Server Address: Port field, enter the IP address or domain name of the
Outbound Proxy Server and the number of the Outbound Proxy Server’s Listening Port for SIP.
The Server Address may consist of maximum 40 characters. Default: Blank.
The valid range for the port is 1024-65534. Default: 5060.
10.
To add ‘rinstance’ in the REGISTER Message, keep this feature enabled. Default: Disabled.
‘rinstance’ is any random value which can be used by the SETU ATA211G to fetch its own contact binding, i.e. to know the Registration Expiry Timer assigned by the server.
When you enable ‘rinstance’ in Register, SETU ATA211G will generate any random value of 'rinstance' and include in the REGISTER message. The system will use the registration expiry timer of that contact binding.
11.
Set the Re-registration Timer. This is the time period after which the SETU ATA211G will send registration request to maintain registration binding with the Registrar server.
12.
The valid range of this timer is 00001- 65535. Default: 3600 seconds.
Define the Registration Retry Timer. When a registration attempt fails, SETU ATA211G will resend registration request to the Registrar Server after the expiry of the Re-registration Timer. The valid range of this timer is from 00001- 65535. Default: 10 seconds.
13.
Click Submit.
Incoming Call
1.
Select an appropriate Incoming Call Routing option for the SIP Trunk. You may select:
Reject Incoming Calls: The system will reject all calls received on the SIP Trunk. Select this option, if you want to block calls on this SIP trunk.
Matrix SETU ATA211G System Manual 29
30
• Route To FXS: The system will place all calls received on the SIP Trunk on the FXS port. The phone connected to the port will start ringing for the duration of the Ring Timer (default: 45 seconds). If the call is not answered within this timer, it will be rejected. This is also the default routing option.
• Route to fixed destination number through Mobile: The system will place all calls received on the
SIP Trunk to a Fixed Destination Number through the Mobile port.
If you select this option, define the destination number in the Fixed Destination Number field.
• Route to FXS. If not answered within ring timer, route to fixed destination number through
Mobile: The system will place all calls received on the SIP Trunk on the FXS port. The phone connected to the port will start ringing for the duration of the Ring Timer (default: 45 seconds). If the call is not answered within this timer, the call will be automatically routed to the Fixed Destination
Number through the Mobile port.
If you select this option, define the destination number in the Fixed Destination Number field.
• Answer the call, collect number & route to FXS: Select this option, if FXS port of SETU ATA211G is connected to the FXO port of the PBX and you want callers to reach extensions of the PBX by simply dialing the extension number. When there is an incoming call on the SIP trunk, the call is answered and dial tone is played to the caller. When the caller dials the number, ATA will collect the digits and route the call from its FXS port.
• Answer the call, collect number & route to Mobile: Select this option, if you want the system to first answer the call on the SIP trunk, play dial tone to the caller, and when the caller dials the number, to collect the digits and route the call to the Mobile port.
• Route as per called party number: Select this option, if you want all incoming calls on the SIP trunk to be routed on the basis of the Called Party Number received in INVITE message.
If you select this option, you must configure the Called Party Number Table. See
for instructions.
• Enter the Fixed Destination Number in this field, if the incoming call routing option requires the call to be finally placed at a fixed destination. You can configure the fixed destination number of maximum 16 digits.
Default: Blank
• Enter the time duration in the Ring Timer field, for which the system plays the ring on the FXS Port for an incoming call. Range of the ring timer is of 01 to 99 seconds. Default: 45 sec.
2.
SETU ATA211G supports display of Calling Line Identity (CLI) received in the SIP request message on the
FXS port. To display CLI Number on FXS Port, you may select:
• Calling Number
• Called Number
Default: Calling Number
3.
Define the type of response the system should send on the receipt of an incoming call on the SIP trunk.
For the On Connecting Media, Send parameter, you may select:
• 183 Session Progress
• 200 OK
Default: 183 Session Progress
Matrix SETU ATA211G System Manual
4.
If you want to Authenticate Incoming Calls on SIP, that is, you want to allow incoming calls only after callers have authenticated themselves. You can select:
• PIN: Select this option to authenticate callers with a unique PIN.
• Digest: Select this type of authentication if you want to allow incoming calls on the SIP Trunk only after callers have authenticated themselves with their User ID and Password .
Default: Disabled.
If you have selected PIN, you must configure the PIN Authentication Table. To do this,
• Click the arrow icon.
• The PIN Authentication page opens in a new window.
Matrix SETU ATA211G System Manual 31
• Enter the PIN to be authenticated against each Index in the Table.
The PIN number can have a maximum of 4 digits. The characters allowed are: 0-9,*, #
• If you have finished entering, click Submit to save.
• Close the window. See
If you enable Digest Authentication, you must configure the Digest Authentication Table. To do this,
• Click the arrow icon.
• The Digest Authentication Table page opens in a new window.
32 Matrix SETU ATA211G System Manual
• Enter the User ID to be authenticated along with its corresponding Password against each Index in the Table.
The User ID may be a maximum of 40 characters. The User Password may be a maximum of 16 characters.
• If you have finished entering the User IDs and their corresponding User Passwords in this Table, click Submit.
• Close the window.
To know more about this feature, see “Digest Authentication”.
Vocoders
1.
Select Vocoders in the order of preference from the multiple selection box.
Vocoders are the various voice codecs used to compress the data in RTP packets for optimum use of bandwidth and for ensuring voice quality. You can set 4 Vocoder options in the order of preference.
The Vocoders supported by SETU ATA211G in the order of preference, i.e. 1st to 4th, listed in the Used
Codecs box are:
• G.711 A - Law
• G.711 Law
• G.729
• G.723
• To remove a Vocoder from this list, select the Vococder and click the back arrow <
• The Vocoder will be moved to the Unused Codecs box.
• Select the required Vocoders your cursor from the right list box.
• Use the Up and Down arrows near the Used Codecs box to change the order of Vocoder preference.
2.
If you have G.723 as a Preferred Vocoder, select G.723 Bit Rate as 5.3 Kbps or 6.3 Kbps. Default:
6.3kpbs.
When G.723 is negotiated, the selected Bit Rate will be applied only when sending the RTP packets.
When receiving RTP packets from the remote end, both Bit Rates of G.723 will be accepted.
Matrix SETU ATA211G System Manual 33
Advanced
34
1.
Select the default SIP Transport for outgoing SIP messages from the following options:
• UDP: Outgoing messages are transported using UDP.
• TCP: Outgoing messages are transported using TCP.
• TCP (Fallback to UDP): TCP is used for outgoing messages. However, if the TCP connection fails, the system will attempt to send the message again over UDP.
Default: UDP
To use TCP or TCP (Fallback to UDP), you must enable SIP over TCP in the
page.
2.
Select the Automatic Number Translation check box, if you want to apply this feature on the SIP trunk.
Default: Disabled.
Automatic Number Translation (ANT) of SETU ATA211G modifies the number strings - entire numbers or part thereof - you dial into number strings understood by the IP network.
The ANT feature is useful when the network requires adding or stripping off of parts of the dialed number strings. For example, the PSTN requires you to dial the prefix 00 for calling international numbers, whereas the ITSP you have subscribed this SIP trunk restricts the dialing of the prefix 00 for international numbers. If you happen to dial this prefix, your call will be rejected by the ITSP.
Matrix SETU ATA211G System Manual
ANT is also used when SETU ATA211G is deployed for networking between PBXs at multiple sites, and
is required.
To use ANT, select the check box and configure the Automatic Number Translation Table. To do this,
• Make a list of numbers that need to be modified before being dialed out from this SIP trunk. Make a list of the corresponding modified numbers that the system should substitute the dialed numbers with.
• Click the arrow icon.
• The Automatic Number Translation table opens in a new window.
In this table, you can store as many as 24 Dialed Numbers and their corresponding Substitute
Numbers, at Index Numbers 01 to 24.
Matrix SETU ATA211G System Manual 35
36
• In the Dialed Number column, enter the numbers that need to be modified when dialed out from this
SIP trunk.
• In the Substitute Number column, enter the numbers which the system should dial out in place of the dialed numbers.
Make sure you enter a Dialed Number and its corresponding Substitute Number at the same Index number in the table. For example, if you entered 001 as Dialed Number at Index 01, you must enter its corresponding Substitute Number 1 also at Index 01.
• Click Submit to save your entries.
• Close the window.
3.
By default, the CLI of the SIP Trunk is sent to the called party when outgoing calls are made using the SIP trunk. If you do not want to send CLI, enable CLIR check box.
4.
Select the FXS/Mobile check box to select the CLI source type you want ATA to send (in the SIP message) during an outgoing call as the CLI.
If FXS is the source port, the FXS Port Number is sent as CLI. If Mobile is the source port, the same CLI received on the port is sent.
5.
If you want the system to reject incoming calls which do not have the identity of the caller (Calling Party
Information), enable the Anonymous Call Rejection check box. Default: Disabled.
6.
If you want the system to send RTP packets to original IP and Port from where RTP packets are received, by ignoring the contact information received in SDP, enable the Symmetric RTP check box. Default:
Disabled.
7.
If you want the system to send DNS SRV query to the configured domain server, enable DNS SRV. When disabled, the system will send DNS A query to the configured domain server. Default: Disabled.
8.
When the system is installed behind a NAT Router, select specific NAT traversal mechanism to be used as
NAT Type.
• Select Router’s IP Address, if your ATA is located behind the NAT router (any type).
Make sure you disable Outbound Proxy on SIP trunk and configure the same IP Address under NAT settings in the
page.
• Select STUN if your ATA is located behind the NAT router other than Symmetric.
Make sure you disable Outbound Proxy on SIP trunk and configure the STUN Server Address and port in
.
9.
Select the appropriate DTMF sending/receiving mechanism that is compatible with the DTMF sending/ receiving mechanism of your ITSP or remote peer. SETU ATA211G supports:
• Inband
• Outband
• SIP (INFO)
Default: Outband
Matrix SETU ATA211G System Manual
• In the On Time field, set the time for which the DTMF digit should remain on, when the digit is dialed out by the system. The DTMF On Time may be 100 or 150 or 200 milliseconds. Default: 100 milliseconds.
• In the Off Time field, set the time for which system should wait before dialing the successive DTMF digits. The DTMF Off Time may be 100 or 150 or 200 milliseconds. Default: 100 milliseconds.
10.
Configure the Pause Timer (sec), if you want to insert a delay before the digits of a number string is out dialed from the SIP trunk.
The Pause Timer is typically used in
The range of the Pause Timer is from 1 to 9 seconds. Default: 2 seconds.
11.
Select an appropriate Call Hold Method that is compatible with your ITSP proxy server/remote peer.You may select:
• RFC 3261
• RFC 2543
Default: RFC 3261
12.
To send and receive the Fax over IP from and on the FAX machine connected to FXS port of the SETU
ATA211G, select the desired Fax over IP protocol:
• T.38 (UDPTL): If you select this option, the device you are sending the fax to, must also support this protocol.
• Pass Through: Select this option if you need to send fax over G.711. The device you are sending fax to must also use G.711.
Default: T.38 (UDPTL).
If the FAX sent using T.38 is rejected, SETU ATA211G will use Pass Through as the Fall Back protocol to send the fax.
13.
In the Returned Calls to Original Caller (RCOC) option, enable the type of RCOC you want to set for the
SIP Trunk. See “Return Call to Original Caller (RCOC)”
• On Busy: Enable this type if you want to set RCOC when the call is returned if the called party is found busy.
• On No Response: Enable this type if you want to set RCOC when the call is returned if the called party does not answer the call.
• On Speech: Enable this type if you want to set RCOC when the call is returned after speech was established with the called party.
14.
If you have completed the configuration of SIP Trunk 1, click Submit to save settings.
15.
To configure another SIP trunk, click the SIP Trunk Number tab.
16.
Follow the same instructions as described here to configure the next SIP trunk.
Matrix SETU ATA211G System Manual 37
Mobile Port
SETU ATA211G supports a Mobile Port. Insert the SIM card in the SIM holder to get your ATA211G connected to the GSM network.
To configure the Mobile Port parameters,
1.
Click Mobile.
2.
Click More button to view all Mobile parameters on this page.
General
38
1.
Select the Enable check box to use the Mobile Port. Default: Disabled.
You may disable the Mobile Port, if you do not want to include it in Call Routing.
Matrix SETU ATA211G System Manual
2.
You can assign a Name to the Mobile port, which will be displayed to the called party (if the instrument of the called party supports display name functionality).
The name you assign may consist of a maximum of 24 characters. Default: Blank.
Incoming Call
1.
Select an appropriate Incoming Call Routing option for the Mobile Port. You may select:
• Reject Incoming Calls: Select this option if you want ATA211G to reject the incoming calls on the Mobile port.
• Route to FXS: Select this option if you want to route the incoming calls on Mobile port, to the FXS port.
The incoming call will be placed on the FXS Port and the phone connected to the FXS Port will start ringing for the duration of the Ring Timer (default: 45 seconds). If the call is not answered within this timer, it will be rejected. This is also the default option.
If you select this option, you may configure the Ring Timer. Valid range of this timer is 01-99 seconds.
• Route to fixed destination number as per incoming call route selection: Select this option if you want incoming calls on the Mobile Port to be routed to a Fixed Destination Number as per the Incoming Call
Route you select: SIP1, SIP2, SIP3 or Dialed Number Table .
If you select this option, define the destination number in the Fixed Destination Number field and select the Incoming Call Route.
• Route to FXS. If not answered within ring timer, route to fixed destination number as per incoming
call route selection: Select this option if you want to route the incoming calls on the Mobile Port to the
FXS Port first. The phone connected to the FXS Port will start ringing for the duration of the Ring Timer
(default: 45 seconds). If the call is not answered within this timer, the call will be automatically routed to the
Fixed Destination Number as per the Incoming Call Route you select: SIP1, SIP2, SIP3 or Dialed Number
Table.
If you select this option, define the destination number in the Fixed Destination Number field and select the Incoming Call Route.
Matrix SETU ATA211G System Manual 39
• Answer the call, collect number & route as per incoming call route selection: Select this option if you want the system to first answer the call on the Mobile Port, play dial tone to the caller, collect the digits dialed by the caller and route the call as per the Incoming Call Route you select: SIP1, SIP2, SIP3 or
Dialed Number Table .
If you select this option, select the Incoming Call Route.
• Route to FXS. If not answered within ring timer, answer the call, collect number & route as per
incoming call route selection: Select this option if you want to route the incoming calls on the Mobile
Port to the FXS Port first. The phone connected to the FXS Port will start ringing for the duration of the
Ring Timer (default: 45 seconds). If the call is not answered within this timer, the system answers the call, plays dial tone to the caller. When the caller dials the number, the system collects the digits and routes the call as per the Incoming Call Route you select: SIP1, SIP2, SIP3 or Dialed Number Table.
If you select this option, select the Incoming Call Route. You may also configure the Ring Timer.
• Fixed Destination Number: Enter the fixed destination number, if the incoming call routing option you selected requires the call to be finally placed to a fixed destination number.
This destination number can be configured of maximum 40 characters.
• Incoming Call Route: You need to configure this parameter, only if the Incoming Call Routing option you selected above requires the Incoming Call Route to be selected. You may select:
• SIP1/SIP2/SIP3: Select this option as Incoming Call Route if you want to route the incoming call received on Mobile port using SIP1/SIP2/SIP3 trunk.
• Dialed Number Table: Select this option Incoming Call Route if you want SETU ATA211G to route the incoming call on the basis of the number dialed. If you select this option, you must also configure the
Dialed Number Table. To do this,
• Click the arrow icon.
40 Matrix SETU ATA211G System Manual
• The Dialed Number Table opens in a new window.
For each Index number,
• Enter the desired Number you want to store in the table. The number must not exceed 24 characters.
• For the number you entered, define the Minimum Digits, which the system should wait to receive before considering it as a valid number. Default: 01.
• For the number you entered, define the Maximum Digits, which the system should wait to receive before considering it as End of Dialing. Default: 24.
• For the number you entered, select as Destination Route the port the system should use to call the dialed number. Default: SIP 1.
At the bottom of the table, select the destination route for dialed numbers that do not match with any of the entries on this table.
• For calls made from the FXS port, select the the destination trunk for the option If dialed number does not match with either of the programmed number in the Dialed Number Table & call is
made from FXS, route the call through. Default, SIP Trunk 1.
• For calls made from the FXS port, select the the destination trunk for the option If dialed number does not match with either of the programmed number in the Dialed Number Table & call is
made from Mobile, route the call through. Default, SIP Trunk 1.
Matrix SETU ATA211G System Manual 41
•
Click Submit to save entries and close the window. See “Dialed Number Table”.
2.
In the Ring Timer field, set the duration for which the ring should be played on the FXS Port for an incoming call. The range of the Ring Timer is of 01 to 99 seconds. Default: 45 sec.
3.
Select the required type of CLI to be displayed on the FXS Port during an incoming call:
• Calling Number: Select this option if you want the number of the Calling Party to be displayed as CLI on the FXS Port.
• Called Number: Select this option if you want the number of the Called Party to be displayed as CLI on the FXS Port.
4.
If you want to Authenticate Incoming Calls on the Mobile port only after callers have authenticated themselves, enable the PIN Authentication check box. Default: Disabled.
You must configure the PIN Authentication Table. To do this,
• Click the arrow icon.
42 Matrix SETU ATA211G System Manual
• The PIN Authentication table opens in a new page.
• Enter the PIN to be authenticated against each Index in the Table.
The PIN number can have a maximum of 4 digits. The characters allowed are: 0-9,*, #
• If you have finished entering, click Submit to save.
• Close the window. See
Advanced
Matrix SETU ATA211G System Manual 43
44
1.
Select the Automatic Number Translation check box, if you want to apply this feature on the Mobile port.
Default: Disabled.
Automatic Number Translation (ANT) enables you to modify or translate the dialed number into another number. ANT is useful when you need to modify or replace a few digits of the dialed number with other digits, before the system dials out the number.
To apply ANT on the Mobile port, you must enable ANT and configure the Automatic Number Translation
Table with dialed numbers and substitute numbers. To do this,
• Make a list of numbers that need to be modified before being dialed out from the Mobile port. Make a list of the corresponding modified numbers that the system should substitute the dialed numbers with.
• Click the arrow icon.
Matrix SETU ATA211G System Manual
• The Automatic Number Translation table opens in a new window.
In this table, you can store as many as 24 Dialed Numbers and their corresponding Substitute Numbers, at
Index Numbers 01 to 24.
• In the Dialed Number column, enter the numbers that need to be modified when dialed out from the
Mobile Port.
• In the Substitute Number column, enter the numbers which the system should dial out in place of the dialed numbers.
Make sure you enter a Dialed Number and its corresponding Substitute Number at the same Index number in the table. For example, if you entered 001 as Dialed Number at Index 01, you must enter its corresponding Substitute Number 1 also at Index 01.
• Click Submit to save your entries.
• Close the window.
2.
Enable CLIR check box to hide your identity from the called party. Thus, the outgoing calls made by the user on Mobile port will be sent as anonymous calls. CLIR will work only if it is supported by your service provider.
3.
In Mobile Network Selection option, set the network selection mode as Automatic or Manual.
When SETU ATA211G is located in the home region, the SIM card gets registered with the Network
Operator of that SIM only, leading to no extra charges (roaming charges) to the user. Whereas, if SETU
ATA211G is located in an area away from the home region or in an area where more than one Network
Operators of different regions are available, the SIM card may get registered with another available
Network resulting in roaming charges.
Matrix SETU ATA211G System Manual 45
46
The Mobile Network Selection feature of SETU ATA211G enables you to select the GSM network of your choice, either automatically or manually. At Power On, ATA211G will automatically locate and register the SIM with the Network that supports the SIM card installed in it. If the SIM fails to register, it will restart the process of network selection on the expiry of the Network Registration Retry Timer.
• Automatic: Select this option if you want the system to select the GSM network automatically. This will register the SIM with any available GSM network whose signal strength is greater than that of other available networks.
• Manual: Select this option if you want to select the GSM network manually. This will allow you to get your SIM registered with the desired network operator available in that region.
If you select the Mobile Network Selection as Manual, assign priorities to the preferred netwok operators for the registration of the Mobile port in the fields Priority 1 to Priority 9.
Enter Network Operator Codes (MCC and MNC) in the fields Priority 1 to Priority 9.
In these fields, Network Operator Codes (MCC and MNC) are configured according to their priority. So, at every Power on, ATA211G will send a request for available GSM Network Operators, who in turn will respond to the request with a list of available Network Operator Codes. ATA211G will match the available Network Operator Codes with those configured in the fields Priority 1 to Priority 9 and select the Network Operator which best suits your requirement in order of priority. See
4.
In the Band field, select the GSM frequency band supported by your service provider in your country.
ATA211G supports four major GSM frequency bands: GSM 850, EGSM 900, DCS 1800 and PCS 1900
mhz. Default: 900 + 1800 mhz.
If band selection is changed, it will be effective only after ATA211G restarts.
5.
In Transmit Gain field, set the Transmitting Gain of the RF Signal to optimum level by selecting one out of the five different levels: Very Low, Low, Normal, High and Very High. Default: Normal.
6.
In Receive Gain field, set the Receiving Gain of the RF Signal to optimum level by selecting one out of the five different levels: Very Low, Low, Normal, High and Very High. Default: Normal.
7.
In SIM PIN field, enter the unique SIM PIN for the Mobile port of your ATA211G. The SIM PIN you enter here must be of 4 minimum and 8 digits maximum. Default: 1234.
SIM PIN is a security feature used by the GSM network. If this feature is enabled on the SIM Card, the network asks the system for the SIM PIN at every power ON. If the SIM PIN you have programmed here matches with the one stored in the network, the network will mark ATA as present on the network.
8.
In DTMF ON Time field, select the appropriate DTMF On time for sending DTMF digits. The DTMF On
Time is the time for which the DTMF digit which is to be out dialed remains ON. Valid range: 50 to 200 milliseconds. Default: 100 milliseconds.
9.
In DTMF OFF Time field, select the appropriate DTMF OFF time as the time gap between two DTMF digits. This can be set between 20 to 200 milliseconds. Default: 100 milliseconds.
10.
In DTMF Level field, DTMF Level signifies with what magnitude (level/amplitude) the DTMF digits should be out dialed. This can be set between 0 dB to -10.5 dB. Default: -6 dB.
Matrix SETU ATA211G System Manual
11.
You may configure the Pause Timer if you want to insert a delay before dialing the DTMF digits on the
Mobile port. The Pause Timer is typically used in Multi-Stage Dialing. Valid range: 1 to 9 seconds. Default:
2 seconds.
12.
In the Returned Calls to Original Caller (RCOC) option, enable the type of RCOC you want to set for the
Mobile Port.
• On Busy: Enable this type if you want to set RCOC when the call is returned if the called party is found busy.
• On No Response: Enable this type if you want to set RCOC when the call is returned if the called party does not answer the call.
• On Speech: Enable this type if you want to set RCOC when the call is returned after speech was established with the called party.
13.
Select Replace ‘+’ from CLI Yes check box if you want to replace ‘+’ from the CLI (during incoming call on mobile) with some other number string.
When an incoming call is received on the Mobile Port, the received CLI usually has a prefix "+". To replace this prefix with a number string, enable this check box. Default: Disabled.
To replace the prefix with another number you may configure Number String. You can configure the number string of maximum 6 digits.
If you want to remove '+', keep the Number String blank.
14.
Click Submit to save the configurations.
Matrix SETU ATA211G System Manual 47
FXS Port
SETU ATA211G supports an FXS port. Depending upon your requirement, you can either connect an standard, analog telephone instrument to the FXS port, or interface the FXS port with the FXO port of a PBX.
To configure the FXS port parameters,
1.
Click FXS.
2.
Click More button to view all FXS port parameters on this page.
General
48
1.
By default Call Routing is enabled on the FXS port.
Matrix SETU ATA211G System Manual
You may disable the FXS Port and if you do not want to include it in Call Routing.
2.
You can assign a Name to the FXS port, which will be displayed to the called party (if the instrument of the called party supports display name functionality).
The name you assign may consist of a maximum of 24 characters. Default: Blank
3.
You can assign a Number to the FXS port. In case of Peer to Peer calls this number will be displayed to the called party.
The length of the number string may have a maximum of 24 characters. Default: Blank.
Outgoing Call
• Select an appropriate Outgoing Call Routing option on the FXS port. Default: SIP1.
• Select Don't allow outgoing calls, if you do not want to route calls through the FXS port.
• Select Route all calls from SIP1, if you want all outgoing calls from the FXS port to be routed through
SIP Trunk 1.
• Select Route all calls from SIP2, if you want all outgoing calls from the FXS port to be routed through
SIP Trunk 2.
• Select Route all calls from SIP3, if you want all outgoing calls from the FXS port to be routed through
SIP Trunk 3.
• Select Route all calls from Mobile, if you want all outgoing calls from the FXS port to be routed through Mobile.
• Select Route all calls as per Dialed Number Table, if you want specific numbers to be routed though specific SIP Trunks only.
If you select this option, you must configure the Dialed Number Table. To do this,
• Click the arrow icon.
Matrix SETU ATA211G System Manual 49
• The Dialed Number Table opens in a new window.
50
In this table, entries are stored at Index numbers from 001 to 100. For each index number,
• Enter the desired Number (max. 24 characters) you want to store in the table.
• For the number you entered, define the Minimum Digits, which the system should wait to receive before considering it as a valid number. Default: 01.
• For the number you entered, define the Maximum Digits, which the system should wait to receive before considering it as End of Dialing. Default: 24.
• For the number you entered, select as Destination Trunk the SIP Trunk the system should use to call the dialed number. Default: SIP1.
Matrix SETU ATA211G System Manual
• At the bottom of the table, select Destination Trunks for dialed numbers that do not match with any of the entries configured in this table, i.e. the No Match Found.
For calls made from the FXS port, select the the destination trunk for the option If dialed number does not match with either of the programmed number in the Dialed Number Table & call is
made from FXS, route the call through. Default, SIP Trunk 1.
For calls made from the FXS port, select the the destination trunk for the option If dialed number does not match with either of the programmed number in the Dialed Number Table & call is
made from Mobile, route the call through. Default, SIP Trunk 1.
• Click Submit and close the window.
To know more, see “Dialed Number Table”.
4.
In Authenticate Outgoing Calls field, enable the PIN Authentication check box if you want ATA211G to allow outgoing calls from FXS port only after authenticating the user.
If you enable PIN Authentication check box, you must configure PIN Authentication table. To do this,
• Click the arrow.
• The PIN Authentication table opens in a new page.
Matrix SETU ATA211G System Manual 51
• Enter the PIN to be authenticated against each Index in the Table.
The PIN number can be of a maximum of 4 digits. The characters allowed are (0-9,*, #).
• If you have finished entering, click Submit to save.
• Close the window.
To know more about this feature, see “PIN Authentication”.
5.
Enable Auto Mobile Fallback check box if you want ATA to automatically route the calls through the
Mobile port when the internet (ethernet) link is down and the SIP trunks cannot be used for call routing.
When you enable Auto Mobile Fallback, the system plays a beep for one second and routes the call to the
Mobile port. If the Mobile port is disabled, busy, the call goes to error state.
Class of Service
• Select the features of SETU ATA211G in the Class of Service
2
(CoS) of the FXS Port .
SETU ATA211G offers the following set of features in Class of Service:
•
•
•
•
•
•
•
By default all the features are enabled.
You may disable the feature you do not want to allow on the FXS Port.
2. Class of Service (CoS) defines the set features of SETU ATA211G that the phone connected to the FXS port is to be allowed access to.
52 Matrix SETU ATA211G System Manual
Advanced
1.
Select the appropriate Answer Signaling Type on the FXS port.
Answer Signaling is required when SETU ATA211G has a PCO/Billing machine connected on its FXS port.
When a call is made through SETU ATA211G and the called party answers the call, call maturity signal must be generated on the FXS port of SETU ATA211G so that the PCO/Billing device connected to its FXS port can start billing. In the absence of maturity information on the FXS port, the call will not be considered as matured, resulting in inaccurate billing.
• Select None if no answer signaling is to be generated on the FXS port.
• Select Polarity Reversal if answer signaling is to be generated in the form of Polarity Reversal on the
FXS port.
Default: Polarity Reversal.
2.
Select the appropriate Disconnect Signaling Type on the FXS port.
If a PCO machine is connected to the FXS port of the SETU ATA211G, whenever the Called Party (remote party) disconnects, the FXS port of SETU ATA211G needs to be informed of this event in the form of a signal, so that the PCO machine can consider the call as complete and stop billing. In the absence of such a signal, the call will be considered as completed only when the Caller goes On-hook, resulting in inaccurate billing.
• Select None if no signaling is to be generated on FXS for call disconnection.
• Select Polarity Reversal if call disconnection is to be signaled in the form of Polarity Reversal.
• Select Open Loop Disconnect if call disconnection is to be signaled in the form of Open Loop
Disconnect signal.
If you select this option, you must configure the Open Loop Disconnect Timer.
Matrix SETU ATA211G System Manual 53
Default: Polarity Reversal.
• Open Loop Disconnect Timer: If you selected Open Loop Disconnect, you may set the value of this timer, as required. Default: 500 milliseconds.
3.
Select the Subscriber Type for SETU ATA211G. Default: Gateway.
When SETU ATA211G is interfaced with a service provider server—ITSP, the Matrix ETERNITY IP-PBX, or any other PBX—that supports supplementary services that require dialing of Flash, like Call Hold, Call
Transfer, Call Waiting, etc., you must select the Subscriber Type for SETU ATA according to the extent of feature access you want on the FXS Port.
• Select Network, if you want to use the supplementary services supported by the PBX. When you set
SETU ATA211G in the Network mode, you can access the service provider features by dialing flash.
You will not be able to access the local features of SETU ATA211G.
• Select Gateway, if you want to use the supplementary features of SETU ATA211G primarily. In the
Gateway mode, you will also be able to access the supplementary services of the service provider
which requires the dialing of Flash. See “Supplementary Services of Service Provider” .
4.
Select the appropriate CLI Type according to the CLI Type supported by the telephone instrument connected to the FXS port.
SETU ATA211G supports three signaling protocols for CLI on the FXS port:
• DTMF
• FSK-ITU(V.23)
• FSK-BellCore
Default: FSK-BellCore
5.
Configure the Flash Timer, as per your requirement. The Flash timer signifies the time period for which the loop current breaks. SETU ATA211G uses this event to activate various features such as Call Hold, Call
Transfer, etc. Default: 600 msec.
6.
To improve quality of speech, enable Echo Cancellation
3
. Default: Enabled.
Also define the Tail Length depending on the length of the echo. Valid Range: 8 msec to 32 msec.
Default: 32 msec.
7.
Select the appropriate AC Impedance according to the AC Impedance supported by the device connected to the FXS port of SETU ATA211G. The device may be a phone or a PBX. You may select from the following impedance options:
• 600
• 900
• 270 + (750 || 150 nF)
• 220 + (820 || 115 nF)
• 370 + (620 || 310 nF)
• 320 + (1050 || 230 nF)
• 350 + (1000 || 210 nF)
• 200 + (680 || 100 nF)
Default = 600
3. Echo Cancellation is a technique that allows isolation and filtering of unwanted signals caused by echoes during speech.
54 Matrix SETU ATA211G System Manual
8.
If required, you may adjust the Speaking Volume (Transmit) on the FXS port to increase or decrease the volume of your voice being transmitted to the remote party. Select the appropriate Speaking Volume from the drop-down list. Default: 0 db.
9.
You may also adjust the Listening Volume (Receive) on FXS port to increase or decrease the volume of the remote party's voice being transmitted to you. Select the required Listening Volume level from the drop-down list. Default: 0 db.
10.
Click Submit to save the settings.
Matrix SETU ATA211G System Manual 55
Passwords
The system can be programmed by the Administrator or the User, by logging into Jeeves as Admin or User with their respective Passwords.
The default Admin and the default User Password are the same, 1234.
Since the Admin Login gives you access to configure all the parameters of SETU ATA211G, while the User login has access to only user specific parameters, you may change the default password and use different Passwords for Admin and User Login.
The password must not exceed 4 digits. Only the digits 0 to 9 are allowed.
Changing Admin Password
You can change the Admin Password only from Jeeves.
1.
Log in as Admin with your Password.
2.
Click the Basic Settings link on the left pane to expand.
3.
Click Passwords.
4.
In the Admin Password,
• Enter the current password in the Old Password field.
• Enter the new password in the New Password field.
• Type the new password again for confirmation in the Re-Enter to Confirm field.
5.
Click Submit to save.
When you change the Admin Password, you will be logged out of Jeeves.
Restoring Default Admin Password
In case you forget the Admin password, you must set the password to the default value. To do this,
1.
Lift the handset of your phone.
56 Matrix SETU ATA211G System Manual
2.
Dial #***
You will get dial tone after successful execution.
3.
Replace handset.
The Admin password will be set to the default value, if the Default Admin Password when User defaults
the ATA? option is enabled in the System Parameters. To avoid this, make sure you disable this option in the
.
Changing User Password
You can change the User Password only from Jeeves.
To change User Password from Admin Mode:
1.
Log in as Admin.
2.
Click the Basic Settings link on the left pane to expand.
3.
Click Passwords.
4.
In User Password,
• Enter the new password in the New Password field.
• Type the new password again for confirmation in the Re-Enter to Confirm field.
5.
Click Submit to save.
To change User Password from User Mode:
1.
Log in as User.
2.
Click the User Settings link.
Matrix SETU ATA211G System Manual 57
3.
Click the User Password.
4.
Enter the current password in the Old Password field.
5.
Enter the new password in the New Password field.
6.
Type the new password again for confirmation in the Re-Enter to Confirm field.
Restoring Default User Password
The User Password is automatically set to the default value whenever you reinstate factory defaults in the system.
If you want to avoid having to set the entire system configuration to default settings, you may dial the related system command from your phone.
To restore default User Password,
1.
Lift the handset of your phone.
2.
Dial #***
You will get dial tone after successful execution.
3.
Replace handset.
Dialing this command string will also reset the Admin Password to factory default, if the Default Admin
Password when User defaults the ATA? option is enabled in the System Parameters. To avoid this, make sure you disable this option before you default the User Password.
58 Matrix SETU ATA211G System Manual
Network Parameters
1.
Click Network.
2.
Click More button to view all Network parameters on this page.
Routing Mode
• Select Routing Mode, according to your installation scenario as NAT or Bridge. Default: NAT.
• Select NAT as Routing Mode, if the LAN and WAN port of SETU ATA are in different network segments.
You will need to configure NAT as Routing Mode, when the SETU ATA211G is at the edge of the network and multiple hosts are connected behind ATA, and you want to share a common internet connection between all hosts.
Matrix SETU ATA211G System Manual 59
LAN
The LAN port of SETU ATA211G is used for connecting a standalone computer or a LAN Switch.
If you need to change the IP Address or the Subnet Mask of the LAN Port of SETU ATA211G, you may do it now.
Default IP Address of the LAN Port is: 192.168.2.21
Default Subnet Mask of the LAN Port is: 255.255.255.0
WAN
• Select Bridge as Routing Mode, if the LAN and WAN port of SETU ATA are in the same network segment.
Selecting Bridge mode will disable Network Address Translation (NAT) on the WAN port.
When you set SETU ATA211G in Bridge Mode, you need not configure the LAN port IP Address and
Subnet Mask. The WAN and the LAN port of SETU ATA211G can be accessed with the IP Address of the
WAN port.
60
1.
Select the Connection Type according to the IP addressing scheme of the network which SETU
ATA211G is connected: DHCP, PPPoE, and Static.
• Select DHCP, if the network uses a DHCP server to assign the IP address, Subnet Mask and Gateway address to SETU ATA211G.
• Select Static, if you want to assign manually assign the IP address, Subnet Mask and Gateway address manually.
If you selected Static, enter the Static IP Address (default: 192.168.001.196) and the Subnet Mask
(default: 255.255.255.0), and the Gateway Address.
By default, the Connection Type for the WAN port is Static. IP Address: 192.168.001.196, Subnet
Mask: 255.255.255.0.
• Select PPPoE, if the network uses PPPoE.
Matrix SETU ATA211G System Manual
Enter PPPoE User ID (max. 40 characters) and Password (max. 24 characters). You may also enter the PPPoE Service Name (max. 24 characters), if provided.
DNS Server
DNS stands for Domain Name Server which is used to resolve domain name into IP address. You can select either
Static or Automatic.
1.
Select Static if you want to configure DNS manually.
• Enter Primary DNS Address.
• Enter Secondary DNS Address, if available.
Secondary DNS Address will be considered when the request to Primary DNS server fails.
• Enter the DNS Domain Name .
2.
Select Automatic DNS if you want DNS Address and Domain name to be assigned by the DHCP/PPPoE server automatically.
This option will be applicable only if you have enabled DHCP or PPPoE as connection type.
Advanced
1.
If the SETU ATA211G is connected in VLAN network, configure the VLAN/CoS.
This parameter enables the SETU ATA211G to add VLAN header to the packets generated by it. The
VLAN header consists of the VLAN ID (12-bit) and Class of Service (CoS, 3-bit) for prioritization of traffic
4
.
• Select the VLAN/CoS check box to enable VLAN ID tagging on all packets generated by the system.
Default: Disabled.
• Enter the VLAN ID that you have assigned to the VLAN in which the SETU ATA211G is connected. The valid range for this is 0-4094. Default: 1.
• For SIP CoS, define the CoS (priority) bits which will be added in all SIP packets. The range of CoS bits is from 0 to 7. Default: 3.
4. The IEEE 802.1P standard allows Layer2 switches to prioritize the traffic, thus providing Quality of Service (QoS), i.e. better handling of data that pass over a network, thereby resulting in greater reliability and quality. Quality of Service (QoS) on Layer2 is referred to as
Class of Service (CoS) which is defined by IEEE 802.1P.
Matrix SETU ATA211G System Manual 61
• For RTP CoS, define the CoS (priority) bits which will be added in all RTP packets. The range of CoS bits is from 0 to 7. Default: 6.
62
2.
SETU ATA211G will send all SIP messages using SIP QoS setting, enter the SIP DiffServe/ ToS as per your requirement. Valid range is from 00-63, Default: 26
3.
SETU ATA211G will send all the RTP packets with RTP QoS setting, enter the RTP DiffServe/ ToS as per your requirement. Valid range is from 00-63, Default: 46
4.
MAC address selection provides you two options: Unique and Clone. Default: Unique.
Select Unique MAC Address, if you want the system to use the unique MAC address assigned to it as source MAC address on all Ethernet frames.
Select Clone MAC Address, if you want the system to use MAC address other than unique MAC address.
If you select Clone MAC Address, enter the desired MAC address manually in the Clone MAC Address field. MAC address is in hexadecimal format, e.g. 00:50:C2:55:B0:10.
5.
SETU ATA211G has an embedded web server called Jeeves, for system configuration. You may change the Web Server Port as per your requirement. Valid range of the port is: 80, 1024-65535. Default: 80.
6.
SETU ATA211G has an embedded FTP server for Software Upgrade. You may change the FTP Server
Port as per your requirement. Valid range of the port is: 21, 1024-65535. Default: 21.
7.
After you have set all the parameters as per your requirement, click Submit at the bottom of the page to save your Network settings.
8.
You will get a prompt, 'This will restart the system, do you want to continue?'
9.
Click OK. The system will restart.
Matrix SETU ATA211G System Manual
CHAPTER 5
Advanced Settings
The Advanced Settings include the features and facilities listed below::
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Matrix SETU ATA211G System Manual 63
System Parameters
Certain parameters of SETU ATA211G are applied system-wide and are not specific to a port. These parameters are called System Parameters.
To configure System Parameters,
1.
Log into Jeeves as Admin with your password.
2.
Click the Advanced Settings link on the left pane to expand the links.
3.
Click System. The System Parameters page opens.
4.
Click the More button to view all the System parameters on this page. You may configure the following parameters on this page, as required:
General
64
• System Name: You can assign a name to SETU ATA211G, as 'System Name'. This name has significance when multiple SETU ATA211G are connected in the same LAN network.
The Name you assign may contain a maximum of 24 characters. Default: Matrix SETU ATA211G.
• First Digit Wait Timer: The First Digit Wait Timer signifies the time for which the system waits for receiving the first digit after going Off-hook from the FXS Port. On expiry of this timer, the system will give error tone to the user. Valid range: 01 to 99 seconds. Default: 15 seconds.
• Inter Digit Wait Timer: Inter Digit Wait Timer signifies the time period for which the system should wait between two consecutive digits when receiving the digits from the FXS Port. On expiry of this timer, the
number is considered to be complete and is dialed. Refer “Dialed Number Table” topic for information
Matrix SETU ATA211G System Manual
about End of Dialing while dialing minimum or maximum numbers. Valid range: 01 to 99 seconds. Default:
5 seconds.
• Transfer Notification Timer: This is the time for which the system will wait for notification of the status of a transferred call, i.e. whether the transfer target is busy, has answered, has disconnected, etc. Refer
topic to know more. Valid Range: 01-99 secs. Default: 60 seconds.
• Play Routing Tone: By default, when calls are routed from Mobile and SIP trunk and no response is received from the called party, the system Plays Routing Tone to the caller.
You may clear the Play Routing Tone check box, if you do not want the system to play routing tone.
• Call Release Timer: This Timer may also be used to restrict the duration of calls made from the FXS port,
Mobile Port and SIP trunks. This timer allows the system to release the matured calls made from the FXS port, Mobile Port and from SIP trunks after a specified time period.
The Call Release Timer is used for disconnecting calls that remain connected in certain conditions. For example, the FXS port has disconnected the call, but no disconnect event is received from the SIP trunk.
In this case, the call remains live in the system. On the expiry of the Call Release Timer, this call will be disconnected.
To apply this timer, select the Call Release Timer check box and set the Timer to the required duration from 001 to 999 minutes. Default: 999 Minutes.
• VoIP Silence Disconnect Timer: This feature allows the system to disconnect the call if silence is detected during speech, for more than the specified duration.
To apply this timer, select the VoIP Silence Disconnect Timer check box and set the Timer to the required duration from 001 to 99 minutes. Default: 99 Minutes
• RCOC Record Delete Timer: You can delete the RCOC records either automatically by specifying time duration in the field 'RCOC Record Delete Timer'. Valid range: 1 to 999 minutes. Default: 999 minutes.
You can also delete the RCOC records any time you want by clicking the 'Clear RCOC Table' button.
• Forward Error Correction: Forward Error Correction is used for data transmission whereby ATA211G adds redundant data to its messages, which allows the receiver to detect and correct errors without asking the sender for additional data.
Select the Forward Error Correction check box to enable. Default: Disabled.
• Voice Activity Detection: Voice Activity Detection is a software application which allows data network, carrying voice traffic over the internet, to detect the absence of audio and conserve bandwidth by preventing the transmission of Silent Packets over the network.
Select the Voice Activity Detection check box if you want SETU ATA211G to apply Voice Activity
Detection (also called Silence Suppression). Default: Disabled.
• Default 'Admin' password when 'User' defaults the ATA?: By default, the Admin Password will be set to its default value, when the User sets the system to default.
To keep the Admin Password unchanged, disable this flag. Default: Enabled.
Matrix SETU ATA211G System Manual 65
NAT
If you are an ITSP, you may use this flag (disable) to prevent your customers (end users) from setting the
Admin Password to default and gaining unrestricted access to system configuration.
66
• STUN (Simple Traversal of UDP through NAT) server facilitates traversing through most NATs, except symmetric NATs. So, if your router has Symmetric NAT, do not configure STUN.
If your SETU ATA211G is located behind a NAT router that is other than symmetric,
• In the STUN Server Address: Port field, enter the STUN Server Address and the Listening Port of the
STUN Server.
The STUN Server Address can have a maximum of 40 characters.
The valid range of the STUN Server Port is from 1024–65535. Default: 3478.
• Clear the SIP Port fetched using STUN check box, if ATA211G is located behind the NAT router and you have forwarded the SIP listening port of the ATA211G in the router.
Keep the SIP Port fetched using STUN check box enabled, if you have not forwarded the SIP
Listening Port in the router.
Make sure you configure the NAT Type on the SIP Trunk as STUN. See
• Router's Public IP Address: Router’s public IP address specifies the public IP address of the NAT router behind which system is located. Default: Blank.
You need to configure this field only if the system is located behind the NAT router and a Static IP Address is assigned as Public IP Address of the Router.
Make sure you configure the NAT Type on the SIP Trunk as Router’s IP Address. See
Matrix SETU ATA211G System Manual
SIP
• UDP NAT Keep Alive: When SETU ATA211G is connected behind a NAT router and SIP messages are transported over UDP, NAT Keep Alive messages must be sent to refresh the binding in the NAT router.
Select the UDP NAT Keep Alive check box to enable. Default: Disabled.
Select the the type of Keep Alive Message to be sent. You may select either REGISTER or NOTIFY.
Default: NOTIFY.
As Interval, set the time period after which the system should send Keep Alive messages. This time period should be less than the NAT binding timer of the router. The valid range for the UDP NAT Keep Alive
Interval is 001–999 seconds. Default: 120 seconds.
• TCP NAT Keep Alive: When SETU ATA211G is connected behind a NAT router, and SIP messages are transported over TCP, NAT Keep Alive messages must be sent to refresh the binding in the NAT router.
Select the TCP NAT Keep Alive check box, if you want the system to send Keep Alive messages periodically to refresh the binding in the NAT router. Default: disabled.
As Interval, set the time period after which the system should send Keep Alive messages. This time period should be less than the NAT binding timer of the router. The valid range for the TCP NAT Keep Alive
Interval is 001–999 seconds. Default: 120 seconds.
• 100rel/PRACK: This parameter is to be configured if you want to support reliable transmission of (SIP) provisional responses.
Select the 100rel/PRACK Enable check box, if you want the SETU ATA211G to use 100rel SIP extension for reliable transmission of SIP provisional responses and to use PRACK (Provisional Acknowledgement).
Default: Disabled.
• SIP Over TCP: SETU ATA211G supports transporting of SIP messages over User Datagram Protocol
(UDP) as well as Transfer Control Protocol (TCP) connection. Despite the advantages that SIP over TCP offers, it is more common to use UDP to transport SIP messages.
Matrix SETU ATA211G System Manual 67
68
By default, SIP over TCP is enabled. If you want to receive SIP messages over TCP keep this option enabled.
You must also enable TCP or TCP (Fallback to UDP) on the SIP Trunk.
• SIP UDP Port: This is the port on which the SETU ATA211G listens for SIP messages transported over
UDP. This port is also used as the source port for sending SIP messages to the remote peer. The valid range for this port is 1024–65534. Default: 5060.
• SIP TCP Port: This is the port on which the SETU ATA211G listens for SIP messages transported over
TCP. This port is also used as the source port for sending SIP messages to the remote peer. The valid range for this port is 1025–65534. Default: 5060.
• RTP Listening Port: This is the port on which the SETU ATA211G listens for RTP Packets. This port is also used as the source port for sending RTP packets to the remote peer. The valid range for this port is
1024–65526. Default: 8000.
• SIP INVITE Timer: This is the time in seconds for which SETU ATA211G waits for a response from the called party after sending INVITE message. This timer starts after sending INVITE message to the called party and stops on receipt of the provisional response or the final response or when the user disconnects the call. On expiry of the timer, the SETU ATA211G terminates the call process and gives an error tone to the user. The range of the SIP INVITE TIMER is 010–180 seconds. Default: 30 seconds.
• SIP Provisional Timer: This is the time in seconds for which SETU ATA211G waits for final response after receiving the provisional response from the called party. This timer starts on the receipt of the provisional response from the called party and stops on receipt of the final response from the called party or when the user disconnects the call. On expiry of the timer, the SETU ATA211G terminates the call process and gives error tone to the user. The range of SIP Provisional Timer is 010–180 seconds. Default: 20 seconds.
• General Request Timer: This is the time in seconds for which the SETU ATA211G waits for response of a transaction request. This timer starts on initiating a transaction and stops on the receipt of a response for the request. On expiry of the timer, the SETU ATA211G clears the transaction. This timer is used for
Registration request, etc. The range of the General Request Timer is 10–60 seconds. Default: 20 seconds.
• Click Submit to save the settings.
Matrix SETU ATA211G System Manual
Called Party Number Table
Called Party Number Table is used for routing incoming calls on the SIP trunks on the basis of the Called Party
Number received, without answering the call.
You must configure this table, if you have selected 'Route as per called party number' as the Incoming Call
Routing option for the SIP trunk.
In the Called Party Number Table, you can store a maximum of 10 numbers.
Each number is stored at an Index in the table. For each number that you enter in the table, you must define the minimum and maximum digit length and select the desired port—FXS or Mobile—to route the call.
Consider the following example of the Called Party Number Table:
Index Number
01 (No match found)
02 2
03 3
04 98
05 00
Minimum Digit Maximum Digit Destination Route
01 24 Mobile
7
7
10
12
7
7
10
12
Mobile
Mobile
FXS
FXS
In this Table:
• The Called Party Number strings received in the incoming call are stored in the Number column against
Index 02 to 10. The first Index is reserved for the No Match Found Entry. The numbers may be prefixes or the complete number strings.
• For each number, the digit length is defined as Minimum Digit and Maximum Digit.
• For each number, the port to be used for routing the call is selected as the Destination Route.
• The incoming calls received from local numbers are to be routed through the Mobile port. These are 7 digit numbers starting with ‘2’ or ‘3’. So, the prefixes of these numbers, '2' and ‘3’ are entered in the
Number field. The Minimum and Maximum Digits are defined as ‘7’. The Destination Route is selected as Mobile port.
• Incoming calls from mobile numbers starting with ‘98’ are to be routed to the FXS port. Since the mobile numbers are 10 digit numbers, the Minimum and Maximum digits are configured as ‘10’ and the
Destination Route is selected as FXS.
• Twelve-digit numbers starting with ‘00’, are to be routed through the FXS port. So, the Minimum and
Maximum digits are configured as ‘12’ and the Destination Route is selected as FXS.
When there is an incoming call and the incoming call routing option is selected as Route as per called party
number, the system will check the Called Party Number.
It will use the best match logic to match the number with the table. If the number received starts with ‘2’, the system will match with the entry at Index02. The system will match the length of the digits with the minimum and maximum configured for the entry at Index02. If the minimum and maximum digits match the system routes the call through the Mobile port selected as Destination Route for numbers starting with ‘2’.
Matrix SETU ATA211G System Manual 69
To be considered as a valid number, the number received must be equal to or more than the Minimum digits configured. If the number received matches the Minimum digits but exceeds the maximum digits, the system will strip off the extra digits and route the number.
If the incoming CLI does not match with any entry in Called Party Number Table (i.e. the number does not exist in the table, the call will be routed through the destination route for the first entry at Index 001, i.e. the No Match
Found entry, in the table.
To configure Called Party Number Table,
1.
Log in as Admin with your password.
2.
Click the Advanced Settings link on the left pane to expand.
3.
Click Called Party Number Table.
The Called Party Number Table page opens.
70
4.
For each Index number,
• Enter the desired Number you want to store in the table. The number must not exceed 24 characters.
The first Index number 01, is reserved for No Match Found. Start your entries from Index 02.
• For the number you entered, define the Minimum Digits, which the system should wait to receive before considering it as a valid number. Default: 01.
• For the number you entered, define the Maximum Digits, which the system should wait to receive before considering it as a valid number. Default: 24.
• For the number you entered, select required Destination Route, the system should use to route the incoming call. Default: None for Index 01 and Mobile for Index02 to 10.
5.
Click Submit save your entries.
Matrix SETU ATA211G System Manual
Dialed Number Table
Dialed Number Table allows the SETU ATA211G to select the most suitable trunk for outgoing calls on the basis of the number dialed.
You must configure this table, if you have selected 'Dialed number based routing' for the FXS Port and the Mobile
Port.
The Dialed Number Table is a list of numbers or part numbers (which you must configure), with a preferred destination port/trunk for each number: FXS, SIP1, SIP2, SIP3, or Mobile. When the user dials a number, SETU
ATA211G checks the Dialed Number Table for a match using the best fit logic. If a match is found, it uses the port/ trunk selected for the number in the table to route the call.
In the Dialed Number table, up to 100 numbers can be stored.
Each number is stored at an Index in the table. For each number that you enter in the table, you must define:
• the minimum number of digits that the system should wait to receive to consider it a valid number to be dialed out.
• the maximum number of digits which the system should wait to receive to consider it as
and dial out the number.
• the Destination Route (SIP Trunk, Mobile port or FXS port), which the system should use to dial out the number.
The Dialed Number Table is to be configured only if you have selected:
• the Outgoing Call Routing option for the FXS port as Route all calls as per Dialed Number Table.
• the Incoming Call Route for the Mobile port as Dialed Number Table.
When a number is dialed from the FXS port or received on the Mobile port,
• SETU ATA211G will match the dialed number with the entries of the Dialed Number Table.
• If a match is found, it will check the Minimum Digits programmed for this entry to consider it a valid number.
If the length of the number string you dialed matches with the Minimum Digits programmed for this entry, and
is detected
5
, the system will consider it as a valid number. It will not wait to match it with the Maximum Digits you configured for this entry. The system will dial out the number using the
Destination Route you have selected for this entry in the table.
However, if the number of digits dialed by you are less than the Minimum Digits you configured, you will get error tone.
• If the dialed number string exceeds the Minimum Digits, but is less than the Maximum Digits, the system will check the Maximum Digits programmed for this entry.
• If the length of the dialed number string equals the Maximum Digits programmed for this entry, the system will not wait for further digits to be dialed. It will consider the Maximum Digits defined as End of Dialing, and will dial out the number using the Destination Route you selected for this entry in the table.
5. You pressed the # key or the Inter Digit Wait Timer has expired. See “End of Dialing”.
Matrix SETU ATA211G System Manual 71
• You can also configure the Destination Route for dialed numbers that do not match with the table by the
Source Port.
• If the Mobile port is the Source Port, you can route the call through — SIP1/SIP2/SIP3 or FXS.
• If FXS port is the Source Port, you can route the call through— SIP1/SIP2/SIP3, or Mobile.
• You can also restrict dialed numbers that do not match with the table by not selecting any destination route.
Configuring Dialed Number Table
If you have not already configured the Dialed Number Table for the FXS and Mobile port, you may do so now.
1.
Log in as Admin.
2.
Click the Advanced Settings link on the left pane to expand.
3.
Click Dialed Number Table. The Dialed Number Table page opens.
72 Matrix SETU ATA211G System Manual
4.
For each Index number,
• Enter the desired Number you want to store in the table. The number must not exceed 24 characters.
• For the number you entered, define the Minimum Digits, which the system should wait to receive before considering it as a valid number. Default: 01.
• For the number you entered, define the Maximum Digits, which the system should wait to receive before considering it as End of Dialing. Default: 24.
• For the number you entered, select as Destination Route the port the system should use to call the dialed number. Default: SIP 1
• At the bottom of the table, select the Destination Trunk for dialed numbers that do not match with any of the entries configured in this table (No Match Found) by the Source Port.
• For calls made from the FXS port, select the destination trunk for the option If dialed number does not match with either of the programmed number in the Dialed Number Table & call is made
from FXS, route the call through. Default, SIP Trunk 1.
If you do not want to route the dialed numbers from the FXS port that do not match with the table, select None. The System will reject the call.
• For calls made from the Mobile port, select the destination trunk for the option If dialed number does not match with either of the programmed number in the Dialed Number Table & call is
made from Mobile, route the call through. Default, SIP Trunk 1.
If you do not want to route the dialed numbers from the Mobile port that do not match with the table, select None. The System will reject the call.
5.
Click Submit to save your entries.
Matrix SETU ATA211G System Manual 73
Peer-to-Peer Numbers
Calls made between two IP clients without the intervention of a Proxy Server are defined as Peer-to-Peer Calls
(P2P calls). P2P call can be made from FXS or Mobile port.
As the Peer-to-Peer call application does not require a SIP server, voice communication using this application is done virtually free of cost. The major cost savings offered by this application makes it a very attractive mode of inter-branch or intra-office voice communication.
Peer-to-Peer call applications can also be used by residential users for making overseas calls at no cost.
A maximum of 500 locations can be interfaced using ATA211G.
To use this feature:
• There must be a SETU ATA211G installed at each location.
• The SETU ATA211G at each location must have a Static IP Address.
Let us take the installation scenario illustrated below as an example.
74
Location-A
2001
FXS WAN
190.1.1.200
ATA211G
LAN Mobile
Broadband
Modem/Router
GSM Network
IP Network
Location-B
Broadband
Modem/Router
190.1.1.100
WAN FXS
ATA211G
Mobile LAN
GSM Network
3001
• At both locations ATA is directly connected to the IP network.
• At each location, you must do the following configuration:
• enable a SIP trunk to be used for Peer-to-Peer calling.
• set the SIP Trunk Mode to Peer-to-Peer.
• configure the number callers must dial to reach this SIP trunk as its SIP ID.
• set the Incoming Call Routing option on the SIP trunk as Route to FXS.
• configure Outgoing Call Route on the FXS port.
• configure Incoming Call Routing on the Mobile port.
• configure the Peer-to-Peer table.
The Peer-to-Peer table stores upto 500 entries. Each entry consists of the parameters Number, Name,
Minimum Digits, Maximum Digits and Destination Address.
• In this example, you would have to configure the Peer-to-Peer table as follows:
• At Location A, in the Number field of the Peer-to-Peer table, enter the Number you want to dial to call the phone at Location B. In this case, 3001.
Matrix SETU ATA211G System Manual
• For the number you entered, in the Destination Address field in the table, enter the IP Address of the WAN Port of ATA connected at Location B. In this case, 190.1.1.100
• For the number you entered, configure the digit length in the table. As the number you want to dial,
3001, has four digits, configure Minimum Digit for this number as ‘4’. Also configure the Maximum
Digit as ‘4’.
The Peer-to-Peer table you configure for SETU ATA211G at Location-A would look like this:
Index Number
001 No Match Found
002 3001
003
004
Name Minimum Maximum Digit Destination Address
01
04
24
04 190.1.1.100
As the system uses the best match logic to match number strings in the Peer-to-Peer table, you may configure only the prefix of the number to be dialed. Instead of the complete number string, you may configure only the prefix as follows, the system will place all calls that start with ‘3’ to the IP
Address 190.1.1.100
Index
001
002
003
004
Number
No Match Found
3
01
04
Maximum Digit
24
04
Destination Address
190.1.1.100
• Similarly, the Peer-to-Peer table you configure at Location-B should look like this:
Index Number
001 No Match Found
002
003
2001
004
Name Minimum Maximum Digit Destination Address
01
04
24
04 190.1.1.200
• When user 2001 of Location-A or a caller on the Mobile port calls 3001, the call is placed to the IP address
190.1.1.100 as the system finds a best match entry for the dialed number at Index 002 of the Peer-to-Peer table.
• On receiving a call, the SETU ATA at Location-B routes this call to the FXS port, 3001.
• Similarly, when the user 3001 of Location B or a caller on the Mobile port, calls 2001, the call is placed to the IP address 190.1.1.200 as the system finds a best match entry for the dialed number at Index 002 of the Peer-to-Peer table.
Matrix SETU ATA211G System Manual 75
Configuring Peer-to-Peer Calling
To use Peer-to-Peer calling, do the following:
• enable the SIP trunk.
• set the SIP Trunk Mode to Peer-to-Peer.
• configure the number callers must dial to reach this SIP trunk as its SIP ID.
• set the Incoming Call Routing option on the SIP trunk as Route to FXS.
• configure Outgoing Call Route on the FXS port.
• configure Incoming Call Routing on the Mobile port.
• configure the Peer-to-Peer table.
If you have not configured the Peer-to-Peer table from the SIP Trunks page under Basic Settings, you may do so now.
1.
Log in as Admin.
2.
Click the Advanced Settings link on the left pane to expand.
3.
Click Peer-to-Peer Numbers. The Peer-to-Peer Table opens.
76
In the Peer-to-Peer table, each entry is stored against an Index Number from 001 to 500. The first entry at
Index001 is reserved for No Match Found.
4.
For each Index number,
• In the Number field, enter the peer-to-peer number string—prefix or entire number—that will be dialed.
The number string must not exceed 24 characters. Default: Blank.
Matrix SETU ATA211G System Manual
If the number to be dialed out is <dialednumber@destination address>, for example, [email protected], you must enter 1234 in this field.
• In the Name field, enter a name to identify the number string you configured. It may be the name of your contact or any name you wish to assign to the number string. The name may consist of 24 characters (maximum). Default: Blank.
The name you configure here will not be used in SIP signaling.
• As Minimum Digits, define the minimum length of the number string that must be dialed for the system to consider it as a valid number. Default: 01.
• As Maximum Digits, define the maximum length of the number string that must be dialed out for the system to consider it the complete number string. Default: 24.
• In the Destination Address field, enter the domain name or IP Address to where the call is to be placed. The Destination Address may consists of up 40 characters (maximum). Default: Blank.
For example, if the peer-to-peer number to be dialed out is [email protected], enter abc.com as
Destination Address. If the number is [email protected], enter 192.168.1.197 as the Destination
Address. The Destination Address can also be in the form of Address: Port number.
5.
Click Submit to save your entries.
You may log out of Jeeves.
Making Peer-to-Peer Calls
To make a Peer-to-Peer Call:
• Go Off-hook.
• Dial the IP Address of the remote party or the number of the remote party stored in the Peer-to-Peer Table.
• To dial an IP Address, press * key (star/asterisk).
For example, to call the IP Address 192.168.200.200, dial 192*168*200*200.
When you press the * key, it is interpreted by the SETU ATA211G as a '.' (dot/period).
• Talk, when the remote party answers the call.
Matrix SETU ATA211G System Manual 77
Mobile Emergency Numbers
SETU ATA211G supports Mobile Emergency Numbers feature which allows you to make calls to emergency services such as Ambulance, Fire Brigade, Police, etc from its Mobile port. Dialing Emergency Numbers from the mobile port is possible even if the SIM card is not inserted in the Mobile port or even when the module is not registered with the GSM network.
The Mobile Emergency Number feature works on the basis of the Emergency Number Table. You must configure this table in Jeeves. The Emergency Number Table supports five entries where only first two entries are configurable and the last three entries are fixed.
Each Emergency Number is stored at an Index in the table. Each Emergency Number is of maximum 3 digits.
• If you dial a number, the system compares the number with the numbers configured in the Number column of the Emergency Number Table.
• The system uses the perfect match logic for matching the dialed number with the configured Emergency
Numbers.
• If the dialed number matches perfectly with the configured Emergency Numbers in the table, then
ATA211G does not wait for the end of dialing and outdials the number automatically.
• If the dialed number does not match perfectly with the configured Emergency Number and the end of dialing is received, then the number is dialed as per outgoing logic.
Configuring Emergency Number Table
To configure Emergency Number Table,
1.
Log in as Admin.
2.
Click the Advanced Settings link on the left pane to expand.
3.
Click Mobile Emergency Numbers. The Mobile Emergency Number Table opens.
78 Matrix SETU ATA211G System Manual
4.
For each Index entry, configure the Emergency Number in the Number column. You can configure each
Emergency Number of maximum 3 digits and 0-9 digits are allowed.
The default Emergency Number Table is as below:
3
4
5
Index Emergency Number
1 Blank
2 Blank
112
911
000
• Avoid configuring conflicting numbers as Emergency Numbers.
• Emergency Numbers have priority over PIN Numbers and Access Codes.
• The system dials out the Emergency Numbers without waiting for End-of-Dialing.
Matrix SETU ATA211G System Manual 79
Digest Authentication
Digest Authentication is a challenge-based authentication service of SIP to authenticate the identity of the originator of SIP request in the INVITE message. The recipient of the request can ascertain whether or not the originator of the request is authorised to make the request. When the digest credentials of the originator - User
Name and Password - in the INVITE message are authenticated and accepted by the recipient, the originator and the recipient are connected.
SETU ATA211G supports Digest Authentication. The Digest Authentication feature works on the basis of the Digest
Authentication Table, in which the credentials, namely the User Name and Passwords of trusted/authorised calling party SIP devices are stored. You must configure this table.
When you enable this feature on a SIP trunk, for all incoming calls (SIP requests),
• SETU ATA211G will challenge the identity of the calling party, i.e. the SIP device initiating the request to send its digest credentials.
• When the calling party sends its credentials, SETU ATA211G authenticates the credentials by matching it with its Digest Authentication Table.
• If a match is found, the calling party will be authenticated and the call will be allowed on the SIP trunk.
• If no match is found, SETU ATA211G will consider it as invalid authentication information and reject the call.
You may use Digest Authentication to
• restrict access to SETU ATA211G to specific callers.
• prevent unwanted or malicious calls.
Let us understand Digest Authentication with the help of an example:
• A Company has its head office in Mumbai and branch offices in the cities of Kolkata, Chennai and New
Delhi.
• For voice communication over IP, the Company has installed SETU ATA211G in all its branches for making
Peer-to-Peer Calls. (For more details, refer
topic).
• The Company wants to use a SIP trunk for exclusively for inter-office calling.
• To be able to do this, the Company must do the following in all its branch offices:
• set the SIP Trunk mode of the desired SIP trunk to Peer-to-Peer mode, and configure Peer-to-Peer
Numbers
6
.
• enable Digest Authentication on this SIP Trunk.
• configure the Digest Authentication Table with the User Name and Password of the SIP devices of all branches, from which calls are to be allowed on this SIP trunk. In this case, the User Name and
Password will be of the dedicated Peer-to-Peer SIP trunk in the branch offices. For example, in the
Digest Authentication Table, you configure at the Mumbai office, you must configure the User Name
6. Static IP address is assigned to the WAN port of all Gateways and the SIP trunks are set to Peer-to-Peer mode in all the offices.
80 Matrix SETU ATA211G System Manual
and Password for the dedicated SIP trunks at the offices in Kolkatta, Chennai and New Delhi. Similarly, in the Digest Authentication Table you configure in the New Delhi office, you must configure the User
Name and Password for the dedicated SIP trunks at the offices in Mumbai, Kolkatta, Chennai.
• With Digest Authentication configured at all branches, whenever an incoming call is received on the
SIP trunk, the SIP trunk will challenge the identity of the caller. When the digest credentials sent by the calling device matches with the Digest Authentication Table, the call will be allowed on the SIP trunk.
• If the digest credentials do not match, the call will be rejected.
• Thus, the Company can use Digest Authentication to restrict all call except those from its branch offices on a SIP trunk.
Configuring Digest Authentication
To use this feature, make sure you have enabled Digest Authentication on the desired SIP Trunk and configure the Digest Authentication Table.
If you have not already configured the Digest Authentication Table on the SIP Trunk parameters page, you may do so now.
1.
Log in as Admin with your Admin Password.
2.
Click the Advanced Settings link on the left pane to expand the links.
3.
Click Digest Authentication.
The Digest Authentication Table page opens. You can configure upto 500 entries in this table. This Table is common for all SIP trunks.
• Enter the user name assigned to the caller/calling device in the User ID field. SETU ATA211G will use this
User ID to match the digest credentials sent by the caller/calling devices when challenged.
Matrix SETU ATA211G System Manual 81
Make sure the User ID you enter here and the User ID assigned at the calling end are the same. The User
ID can be up to 40 characters long. Default: Blank.
• Enter the password to authenticate the user ID in the User Password field. The password may consist of a maximum of 24 characters. Default: Blank.
Make sure the User Password you enter here and the User Password assigned at the calling end are the same.
• Click Submit to save the entries.
•
Now, enable Digest Authentication on the desired SIP Trunk. See “SIP Trunks” for instructions.
82 Matrix SETU ATA211G System Manual
PIN Authentication
SETU ATA211G supports PIN Authentication for outgoing calls from the FXS port and for incoming calls on the
Mobile port and SIP trunks.
You may use PIN Authentication on the Mobile port, the SIP trunks and the FXS port to restrict access to SETU
ATA211G to specific callers.
The PIN Authentication feature works on the basis of the PIN Authentication Table, which you must configure.
When you enable PIN Authentication on the Mobile port or the SIP trunk, for each incoming call,
• ATA211G will answer the call and play Prompt tone to the caller.
• the caller must dial the PIN.
• ATA211G matches the PIN dialed by the caller with the PIN Authentication Table.
• If a match is found, the caller is authenticated. The caller can now dial the number.
• If no match is found ATA211G will play error tone, followed by Prompt tone. The caller is allowed two more attempts to dial the PIN. If PIN Authentication fails again ATA will disconnect the call.
This feature will work on the Mobile port, only if Incoming Call Routing option is selected as:
• Answer the call, collect number & route as per incoming call route selection.
OR
• Route to FXS. If not answered within ring timer, answer the call and route as per incoming call route selection.
This feature will work on the SIP trunk, only if Incoming Call Routing option is selected as:
• Answer the call, collect number & route to FXS.
OR
• Answer the call, collect number & route to Mobile.
Configuring PIN Authentication
To use this feature, make sure you have enabled PIN Authentication on the desired port type: FXS, Mobile, SIP.
•
On the Mobile port, enable the Authenticate Incoming Calls check box. See “Mobile Port”
• On the SIP trunk, enable the Authenticate Incoming Calls check box. See
• For the FXS port, enable the Authenticate Outgoing Call check box. See
Now, configure the PIN Authentication Table.
1.
Log in as Admin.
2.
Click the Advanced Settings link on the left pane to expand the links.
Matrix SETU ATA211G System Manual 83
3.
Click PIN Authentication.
The PIN Authentication Table page opens. You can configure upto 100 entries in this table. This Table is common for authenticating callers on all port types: FXS, Mobile and SIP.
4.
Enter the PIN to be authenticated against each Index in the Table. The PIN can have a maximum of 4 digits. The characters allowed are: 0 to 9,*, #
Default: Blank.
5.
Click Submit to save the entries.
84 Matrix SETU ATA211G System Manual
Daylight Saving Time
Daylight Saving Time (DST) is the practice of advancing clocks so that afternoons have more daylight and mornings have less. Typically clocks are adjusted forward one hour near the start of Spring and are adjusted backward in Autumn. Many countries of the world
7
use it, though the start and end dates of DST vary with location and year.
SETU ATA211G supports Daylight Saving Time adjustment to set the the Date and Time
8
of SETU ATA211G are set forward and backward according to the DST convention followed in your country.
You can set DST by: Day and Month or Date and Month.
When ATA211G is set to default, your DST settings will remain unchanged.
Configuring DST
1.
Log in as Admin.
2.
Click the Advanced Settings link on left pane to expand the links.
3.
Click the Daylight Saving Time link.
4.
Enable the Daylight Saving Time check box. Default: Disabled.
5.
Enter the Time Offset. This is the time which the system will consider to forward the clock at the start of
DST and to set the clock back when DST ends. Default: 60 minutes.
7. In most countries in Asia and Africa, and in certain countries of South America, DST is not observed.
8. SETU ATA211G sets its Date and Time according to the Time Zone you selected, and synchronizes the time according to the NTP
Server you selected. See
Matrix SETU ATA211G System Manual 85
6.
Select the desired DST Type as:
• Day-Month Wise: Select this option if the DST in your country starts and ends on a particular day of the month. For example, if DST starts on the Second Sunday of March and ends on the First Sunday of
October.
OR
• Date-Month Wise: Select this option if the DST in your country starts and ends on a particular date of the month. For example, if DST starts on October 12 and ends on March 15.
Default: Day-Month Wise.
7.
If you selected the Day-Month Wise option, configure the Start and End time for DST.
DST Start
• Select the Ordinal day of the month when DST begins: 1st, 2nd, 3rd, 4th or 5th.
• Select the Day of the month when DST begins: Sunday, Monday, Tuesday, Wednesday, Thursday,
Friday, Saturday.
• Select the Month when DST begins: January to December.
• Set the Time when you want DST to begin. The time mode is in 24 hours format.
Default: 1st, Sunday, March, Time 00 hours and 00 minutes.
DST End
• Select the Ordinal day of the month when DST ends: 1st, 2nd, 3rd, 4th or 5th.
• Select the Day of the month when DST ends: Sunday, Monday, Tuesday, Wednesday, Thursday,
Friday, Saturday.
• Select the Month when DST ends: January to December.
• Set the Time when you want DST to end. The time mode is in 24 hours format.
When the DST of a particular country starts or ends on the Last Sunday or any other day, e.g. the last
Tuesday, last Friday of the month, always set the Ordinal Number as '5th'.
8.
If you select Date-Month Wise option, configure the following parameters:
DST Start
• Select the Month when DST begins: January to December.
• Select the Date on which DST begins: 1 to 31.
• Set the Time when DST begins. The time mode is in 24 hours format.
DST End
• Select the Month when DST ends: January to December.
• Select the Date on which DST ends: 1 to 31.
• Set the Time when DST ends. The time mode is in 24 hours format.
9.
Click Submit to save your DST settings.
Example: If you are installing SETU ATA211G in a country in the European Union, as per the European Summer
Time, the DST would start on the Last Sunday in March and end on the Last Sunday in October each year. Clocks
86 Matrix SETU ATA211G System Manual
are advanced by one hour at 01:00 hours GMT at the start of DST and set back by one hour at 01:00 hours GMT when DST ends.
1.
Select the Enable check box to enable Daylight Saving Time.
2.
Set the Time Offset as 60 minutes.
3.
Select the Day-Month Wise option as DST Type.
4.
Configure the DST Start as follows:
• Select 5th as the Ordinal.
• Select Sunday as the Day.
• Select March as the Month.
• Set Time to 01 Hours and 00 Minutes.
5.
Now, go to the DST End option, and configure as follows.
• Select 5th as the Ordinal.
• Select Sunday as the Day.
• Select October as the Month.
• Set Time to to 01 Hours and 00 Minutes.
6.
Click Submit to save DST settings.
Matrix SETU ATA211G System Manual 87
Static Routing
Static Routing Table is required when you have more than one router (Gateway) in your network and you want
SETU ATA211G to send packets to multiple routers/gateways for different types of calls.
To illustrate this with an example, two Local Area Networks, Network A and Network B, are connected through
Frame Relay/ MPLS network to give access to local resources and also to make Peer-to-Peer calls.
SETU ATA211G connected in a Frame Relay/ MPLS network
59.162.252.82
SIP Proxy
192.168.1.0/24
A B
192.168.2.0/24
Public
IP
Frame Relay/MPLS
ATA211G ATA211G
• SETU ATA211G is connected at both sites behind a router.
• These sites are also connected to public IP network for the following reasons:
• To give internet access to local hosts.
• To access DID service provided by ITSPs to make PSTN/ GSM calls over IP network.
• Network A and Network B are in different subnets.
The Static Routing Table makes it possible to route different types of outgoing calls - Peer to Peer or Proxy - made to different subnets through different Gateways.
The Static Routing Table defines the appropriate Gateway Address (or Router’s LAN Address) where the IP packets are to be sent.
In the Static Routing Table, you must configure:
• The address of the final Destination where the packets are to be sent.
• The Subnet Mask to be applied on the final destination address.
• The Gateway Address where the IP packets are to be sent.
When SETU ATA211G sends packets, if the final destination IP Address and SETU ATA211G are not in the same
Subnet, the system will check the Static Routing Table.
88 Matrix SETU ATA211G System Manual
If a perfect match is found, SETU ATA211G will start sending the IP packets to the corresponding Gateway
Address configured in the table.
If no match is found, SETU ATA211G will send the IP Packets to the default Gateway Address you configured in the
page.
Configuring Static Routing Table
The Static Routing Table must be configured at each location where SETU ATA211G is installed.
1.
Log in as Admin.
2.
Click the Advanced Settings link to expand.
3.
Click Static Routing.
The Static Routing Table opens.
The Static Routing Table allows you to configure up to 5 entries. Each entry is stored against an Index number.
For each entry, you must configure the following fields:
• Destination Address: This is the address of the final destination where the call is to be made. This can be a device IP Address or Network Address.
• Subnet Mask: This is the mask to be applied on destination address.
• Gateway Address: This is the IP address of the node where the IP packets are to be sent. Generally, it is the IP address of the LAN interface of the Router (to which SETU ATA211G is connected).
The Gateway Address must be in the same subnet as SETU ATA211G.
4.
Click Submit to save your entries.
Matrix SETU ATA211G System Manual 89
For example, the Static Routing Table of the SETU ATA211G at Location A, will be as shown below.
Index Destination Address Subnet Mask Gateway Address
1 192.168.2.0
255.255.255.0
192.168.1.1
:
5
Here, the Destination Address 192.168.2.0 specifies the network address of Location B.
The Subnet Mask is the mask to be applied on Destination address.
The Gateway Address 192.168.1.1 specifies the LAN address of the Router used to connect SETU
ATA211G at Location A with SETU ATA211G at Location B.
Now, the IP address of LAN interface of the Router which connects Location A to the Public Internet should be configured as the ‘Default Gateway’ in the Network parameters.
With the Static Routing Table configured as shown above, packets sent by SETU ATA211G to
192.168.2.0/24 will be routed to the router which connects Location A to location B. Whereas, all packets sent to an address other than 192.168.2.0/24 will be routed to the Default Gateway.
90 Matrix SETU ATA211G System Manual
Reinstate Factory Defaults
SETU ATA211G enables you to restore factory settings to all the programmable parameters using the option
Factory Defaults.
You can reinstate Factory Defaults by logging in as Admin or User. The factory set values will be assigned to all parameters depending on the type of login, Admin or User.
When you log in as Admin to reinstate factory defaults, all parameters will be assigned default values except the following:
•
)
•
Daylight Saving Time (DST) Parameters (see “Daylight Saving Time” ).
•
CPTG and Ring (see “Region” ).
When you log in as User to reinstate factory defaults, default values will be assigned to the parameters listed below:
• Supplementary Features
• Speed Dialing
• Network
• User Password
• Syslog
From the User Login, the Admin Password will be set to its default value, 1234, if you have enabled the option
'Default Admin password when ‘User’ defaults the ATA? in the System Parameters. See .
Restoring Factory Default
Using Jeeves
1.
You can login either as Admin or User with your Password.
2.
Click the Advanced Settings link on the left pane to expand.
3.
Click Factory Defaults.
An alert message will be displayed, This option will assign default values to all the programmable
parameters and will Restart. Do you want to continue?
Matrix SETU ATA211G System Manual 91
4.
Click OK.
The system will restart.
To restore Factory Defaults from User mode,
1.
Log in as User.
2.
Click Factory Defaults link under User Settings.
3.
Click OK on the alert message: This option will assign default values to all the programmable
parameters and will Restart. Do you want to continue?
The system will restart.
Using Commands
1.
Lift the handset of the phone.
2.
To log in as Admin, dial the programming access code #19 followed by the Admin Password (default is
1234).
OR
3.
To log in as User, dial the access code #18 followed by User Password (default is 1234).
4.
You will get programming tone.
5.
Dial 21-Reverse Admin/User Password-#*
For example: 21-4321-#* (the reverse of the default password 1234).
instructions.
92 Matrix SETU ATA211G System Manual
Restart SETU ATA211G
If you need to restart SETU ATA211G, you may do it using Jeeves, instead of switching OFF and switching ON the system again.
When you restart the system, all active calls will be disconnected and the ports in use will be released. The system configuration however, will not be affected.
To restart the system using Jeeves,
1.
Log in as Admin.
2.
Click the Advanced Settings link on the left pane to expand.
3.
Click Restart.
4.
An alert message will appear, ‘This will Restart System. Do you want to continue?
5.
Click OK button to restart the system.
94 Matrix SETU ATA211G System Manual
Syslog
Syslogs (debugs) are logs of actions and events that take place on any computer system. These logs are useful for troubleshooting and system security.
SETU ATA211G supports Syslog
9
Client for debugging. Syslog Client enables the system to send debug messages in syslog format to the remote 'Syslog Server' on IP network. You can view the system debug messages on the remote server.
Each debug message includes the MAC Address of SETU ATA211G which is sending debug messages in 'syslog server'.
ATA211G supports following different Syslog levels:
• APPL
• CONFIG
• SYS
• SIP
• CALL
• DSP
• REG
• SNTP
• STACK
• NAT
• AUTO CONFIG
• Mobile
You can select any of these syslog levels, and the Syslog Client will send only the debug messages for the selected level to the remote server on the IP network. For example, if the debug log of Call is required, you can select this option, and disable all others.
To be able to use this feature, you must enable Syslog, configure the Syslog Server Address and define the Server
Port on which Syslog will listen for debug messages.
Syslog uses the UDP as transport protocol and listens on the port 514 (the default listening port).
To debug the System from the Admin mode,
1.
Log in as Admin with your Password.
2.
Click the Advanced Settings link on the left pane to expand.
3.
Click Syslog.
9. Syslog is one of the protocols used extensively for sending debug messages, and is defined in RFC 3164.
Matrix SETU ATA211G System Manual 95
4.
Configure the following parameters:
• Syslog: Select the check box to enable. By default, disabled.
When enabled, the system will send the debug messages to the Syslog Server IP address. Debug report can be viewed on the Syslog Server or any other application which can capture the Syslog messages/debug sent by the system.
• Syslog Server Address : Port: Enter the IP Address of the Syslog Server. A maximum of 15 digits, including 0-9 and '.' (dot) are allowed.
Enter the Listening Port of the Syslog Server from 1024-65535: 514. By default the Syslog port is 514.
• Syslog Levels: Select the desired debug level by selecting the check box. The system will send debug messages only for the level you have selected. By default, all debug levels are selected. Clear the check box to disable the debug level you do not want.
5. Click the Submit button to save the entries.
To debug the System from User mode,
1.
Log in as User.
2.
Click the Syslog link, under User Settings on the left pane.
3.
To configure Syslog settings, refer the steps 4 and 5 described for the Admin mode.
96 Matrix SETU ATA211G System Manual
PCAP
PCAP or packet capture consists of intercepting and logging the traffic passing over a digital network or a part of a network. PCAP intercepts each packet in the data streams that flow across the network, and can decode and analyze its contents.
PCAP can be used, among others, to monitor the network, analyze network problems, debug client/server communications, debug network protocol implementations.
SETU ATA211G supports PCAP Trace, which you can use to detect and diagnose network related problems, for example, when the SIP account is not getting registered, or any SIP related feature is not functioning.
Packets traveling over a network are captured and saved in the system. You can save these trace files (packets captured by the system) on a computer and open these trace files using a graphical packet capture and protocol analysis tool such as Wireshark or Ethereal.
A maximum of 1 MB of packets can be captured and stored in the system.
SETU ATA211G also supports Filters and Promiscuous mode for capturing packets, which you can use to specify the types of data packets to be captured.
To use PCAP Trace from Admin mode,
1.
Log in as Admin.
2.
Click the Advanced Settings link on the left pane to expand.
3.
Click PCAP.
Matrix SETU ATA211G System Manual 97
98
4.
Decide the type of packets to be captured and set the Filter accordingly. The Filter Settings parameter should be maximum 60 characters in length. By default, this field is blank. So, all packets will be captured.
Refer to the following examples to know how to set the Filters.
Examples of Filter settings:
• To capture packets of source port 5060, set the filter as src port 5060
• To capture packets of destination port 80, set the filter as dst port 80
• To capture packets transmitted from IP address 192.168.1.176, set the filter as src host 192.168.1.176
• To capture packets received from IP address 192.168.1.176, set the filter as dst host 192.168.1.176
It is not mandatory to set Filters. When the Filter Settings field is left blank, the system will capture all packets.
5.
You may select the check box to enable Promiscuous Mode if you want. Default: Disabled.
When you enable Promiscuous Mode, the SETU ATA211G will capture all network traffic. However, this will work only in a non-switched environment.
When Promiscuous Mode is disabled, the system will capture only traffic that is directly related to it. Only traffic to, from or routed through the SETU ATA211G will be picked up by the PCAP Trace.
'Filter Settings' and 'Promiscuous Mode' (enabled) will not be cleared during power down.
6.
Click the Start button to begin the capturing of the packets.
7.
Click the Stop button to stop packet capture.
OR
Wait for the system to stop packet capturing. The system stops packet capturing once the maximum allotted memory of 1 MB (RAM) is utilized.
The Status field displays the current activity of packet capturing.
Number of Packets and bytes captured as per the filter setting will be displayed as Packets Captured and
Total Bytes.
Capturing of packets will not stop if you open any other page of Jeeves. So, you may continue using
Jeeves for any other purpose while PCAP Trace is being used.
8.
When the packet capturing is stopped (by you or the system), click the Save Trace File button to save the files on your computer or on another computer.
A dialog box open. You can select the path for saving the trace file.
Matrix SETU ATA211G System Manual
The current packets captured will not be deleted after you have saved the trace file. The current packets will be deleted when you start the PCAP capture again.
9.
You may log out of Jeeves.
10.
Now, you can open the trace files using Wireshark/Ethereal or any other similar software which supports opening of trace files.
To use PCAP Trace from User mode,
1.
Log in as User.
2.
Click the PCAP link, under User Settings on the left pane.
3.
To configure PCAP settings, refer the steps 4 to 10 described for the Admin mode.
Matrix SETU ATA211G System Manual 99
Software Upgradation
SETU ATA211G provides you the facility to upgrade the system software at the click of a button. SETU ATA211G supports an embedded FTP
10
server which can be used for Uploading and Downloading System files, configuration files, drivers etc.
To update configuration settings and firmware,
1.
Log in as Admin with your Password.
2.
Click the Advanced Settings link on the left pane to expand.
3.
Click System Upgrade. The following message box will be displayed.
4.
In the Password field of the window, enter the Admin Password .
5.
The following folders will be displayed:
• system: contains the current firmware/software.
• config: contains the configuration files.
• driver: contains the current driver files.
• web: contains html files.
• dhcp: contains files of DHCP configuration.
• ppp: contains files for PPPoE configuration.
6.
Click any of these folders to view the files that SETU ATA211G is currently using. You may either delete the existing files or copy the existing files to another location (as backup).
7.
Copy the new configuration files from their location and paste these new files in these folders.
Wait for the file transfer to complete.
8.
Restart the system after uploading the files. The new configuration/driver/firmware will be applicable only after the system restarts.
Before you upgrade software, you can save the existing application/configuration/driver/ web pages folders and files as back-up for retrieval, later. For example: if you want to retain the existing Configuration folder for future record, you can save the folder on your computer. When required, you can copy and paste the same folder back on the FTP server of SETU ATA211G.
10.FTP or File Transfer Protocol is a standard Internet Protocol that is used to exchange files between computers on the IP network.
100 Matrix SETU ATA211G System Manual
Auto Configuration
You can use Auto-Configuration to have the system automatically download the configuration files stored at a central location: TFTP/HTTP/HTTPS Server.
This feature is useful for ITSPs and where multiple SETU ATA211G are connected. ITSPs can store the configuration files of each SETU ATA211G that they provide to their customers on the Auto Configuration Server
(ACS). The configuration files of each ATA are to be stored in a folder named by its MAC Address.
When a customer connects to the ITSP network, the SETU ATA211G provided to the customer will automatically download its configuration files stored in its MAC Address folder on the ACS. The customer can thus start using the
SETU ATA211G without the intervention or assistance of a technician, making it a 'plug-and-play' device.
To use this feature, end users must obtain from the ITSP or System Administrator the following information:
1.
IP address of the Auto Configuration Server.
2.
Path of the Folder (containing the configuration files) on the Auto Configuration Server.
3.
The protocol to be used: TFTP, HTTP, HTTPS.
When your ACS uses HTTP, HTTPS protocol for Auto-Configuration, make sure:
• The configuration files of each ATA are stored in a folder by its MAC Address.
• Store the index.html or startup.html or any other default file name used by your server in the MAC Address folder of each ATA.
• This file should include the names of the configuration files of ATA in the same format as provided to you on the CD-ROM supplied to you with your ATA. See the folder name Auto Configuration Sample File on the CD.
When ATA sends GET request to perform Auto-Configuration, server should return index.html or startup.html or other file, which includes the configuration file names to be supplied to ATA. Once ATA receives the file (index.html or startup.html or other) with configuration file names, ATA will send separate requests for each configuration file.
Using Auto Configuration:
1.
Log in as Admin with your Password.
2.
Click the link Advanced Settings on the left pane to expand.
3.
Click Auto Configuration and configure the following parameter.
Matrix SETU ATA211G System Manual 101
102
4.
Auto Configuration: Select the desired method to be used to fetch configuration files. Default: Never.
• Never: Select this option if you do not want Auto-Configuration process to be done during power ON.
• At Each Power ON: Select this option if you want SETU ATA211G to perform Auto-Configuration at each power ON.
• At Next Power ON: Select this option if you want SETU ATA211G to perform Auto-Configuration only during the next power ON. Once Auto-Configuration is done successfully, the option gets changed to
Never.
• Resync Periodically: Select this option when SETU ATA211G does not need to auto configure during power ON, but needs to resynchronize periodically with the ACS to check for updates in the configuration. If you select this option, Auto-Configuration will be performed every time the Resync
Timer ends.
• At Each Power ON & Resync Periodically: Select this option when SETU ATA211G needs to auto configure during power ON and also to resynchronize periodically with the ACS to check for updates in the configuration.
• At Next Power ON & Resync Periodically: Select this option when SETU ATA211G needs to auto configure only during the next power ON but resynchronize periodically with the ACS to check for updates in the configuration. Once Auto-Configuration is done successfully at next power on, the option gets changed to Resync Periodically option.
5.
Protocol: Select the protocol used by the Auto-Configuration Server for file transfer. The system generates file transfer request to the configuration server according to the protocol you selected. Default:
TFTP
• TFTP: Select the radio button, if you want this protocol for the process of Auto-Configuration. TFTP is preferred when Auto Configuration is to be done in Local Area Network (LAN).
• HTTP: Select the radio button, if you want this protocol for the process of Auto-Configuration. HTTP is preferred when Auto-Configuration is to be done in Wide Area Network (WAN).
Matrix SETU ATA211G System Manual
• HTTPS: Select the radio button, if you want this protocol for the process of Auto-Configuration. HTTPS is preferred when security is the concern during Auto-Configuration.
6.
Server Address: Specify the Auto-Configuration Server Address. The Auto-Configuration Server Address resembles the IP Address/Domain of ACS where all configuration files of SETU ATA211G are stored. The server address can be configured using DHCP.
If the server address is to be configured manually, enter TFTP/HTTP/HTTPS server's IP address from where ATA should download the configuration files. Default: Blank.
7.
If you want the system to get the Server Address from the DHCP server, keep this field blank. Make sure that you also set the 'Connection Type' on the Network page to 'DHCP'.
Config Folder Path: Specify the path of the folder (provided by your ITSP / System Administrator) on the
TFTP/HTTP/HTTPS server from where the configuration files are to be downloaded.
When SETU ATA211G gets auto configured, it will send the request for the configuration files to the selected TFTP/HTTP/HTTPS server and restore the files from the folder as per this path.
Default: Blank.
8.
9.
Request Timeout: Request Timeout is used when SETU ATA211G tries to connect to the Auto-
Configuration Server for TCP/TLS binding. This timer specifies for how long SETU ATA211G should wait for successful TCP/TLS binding.
Enter the required time in seconds. The range of Request Timeout is 01-99 seconds. Default: 60 seconds.
Retry Timer: This timer is used if the connection is not established with Auto-Configuration Server before the expiry of the Request Timeout. Then, in such case, SETU ATA211G will try to reconnect automatically after this time interval.
Enter the required time interval in seconds. The range of Retry Timer is 001-999 seconds. Default: 10 seconds.
10.
Resync Timer: Resync Timer is the time after expiry of which SETU ATA211G will send the resync request to check if there is any change in the configuration files. This timer is applicable only when Resync
Periodically or At Each Power ON & Resync Periodically or At Next Power ON & Resync
Periodically options of Auto-Configuration are selected.
Enter the required resync timer in hours. The range of Resync Timer is 001-999 hours. Default: 24 hours.
11.
Click Submit to save.
Matrix SETU ATA211G System Manual 103
CHAPTER 6
Features of SETU ATA211G
Call Hold
Call Hold enables you to put an on-going conversation on hold, and call another person or receive a call from another person. You can retrieve the call you put on hold, after the conversation with the other party has ended.
You can also retrieve the call you put on hold in the middle of the conversation with the other party.
Call Hold is also used in other features like Making Second Call, Call Waiting, Call Transfer- Blind, Call Transfer-
Attended, Call Toggle and 3-Party Conference.
Configuring Call Hold
To use this feature, make sure that the Call Hold feature is enabled in the Class of Service of the FXS port. See
Using Call Hold
• You are in speech with party A.
• To put your call with A on hold, dial Flash.
• A is put on hold. You get feature tone for 7 seconds, followed by error tone.
• To retrieve the call you put on hold, dial Flash again during feature tone or during error tone.
• You will be in speech with A.
• If you go ON-Hook during the feature tone, your call with party A will be disconnected.
• If you go ON-Hook during error tone, you will get ring back. If you go OFF-Hook when your phone rings, you will get connected with party A again.
Matrix SETU ATA211G System Manual 105
Making a Second Call
You can make a second call, by putting the current call on hold.
To use this feature, make sure that the Call Hold feature is enabled in the Class of Service of the FXS port. See
topic.
Making a Second Call
• You are in speech with party A.
• Dial Flash to put party A on Hold.
• You get feature tone.
• Dial the number of the desired party B.
• When party B answers the call, you are in speech with party B.
Making a second call feature can also be used with other features such as Call Transfer-Attended, Call
Toggle and 3-Party Conference.
106 Matrix SETU ATA211G System Manual
Call Transfer
Using Call Transfer you can connect the person you are in speech with, with another party.
SETU ATA211G offers two types of Call Transfer:
• Call Transfer - Blind: You can transfer the call to the desired party, without informing the party of the transfer.
• Call Transfer - Attended: You can transfer the call to the desired party after consulting the party and or obtaining their consent for transfer.
When you transfer a call, SETU ATA211G will wait for the notification from the destination number to which you have transferred the call, for the duration of the 'Transfer Notification Timer'. This timer is set to 60 seconds by default. It can be set to the desired value.
You will be notified about the success or failure of the transfer attempt during this Timer. You will get a confirmation tone, when the call transfer is successful.
To use this feature, make sure that the Call Transfer feature is enabled in the Class of Service of the
FXS port. See
topic.
You may change the default value of the Transfer Notification Timer to the desired duration, if required,
from the “” topic under Advanced Settings.
Using Call Transfer
Call Transfer-Blind
• You are in speech with party A.
• Party A wishes to speak to party B.
• Dial Flash-#6.
• Party A is put on hold, and you will hear dial tone.
• Dial the number of party B.
• On successful transfer, you will get confirmation tone.
• Party A will get connected with party B.
• Replace the handset of your phone.
When you transfer a call, remain Off-hook, i.e. do not replace your handset, after dialing the transfer destination’s number, until you know the result of the call transfer. One of the following results may occur:
• If the transfer is successful, you will get confirmation tone for 3 seconds, followed by error tone.
• If the transfer has failed, you will get error tone for 2 seconds and you will be connected to the transferee (party A, in this case).
• If the transfer has timed out, i.e. the Notification Timer has expired and no notification has been received from the transfer target (party B, in this case) you will get continuos error tone.
Call Transfer-Attended
• You are in speech with party A.
• Party A wishes to speak to party B.
• Dial Flash.
• Party A is put on hold, and you will hear dial tone.
Matrix SETU ATA211G System Manual 107
• Dial the number of party B.
• When party B answers the call, you will be in speech with party B.
• You may now transfer the call if party B consents.
• Dial Flash-#7 to transfer the call to party B.
• On successful transfer, you will get confirmation tone, followed by dial tone.
• Party A will get connected with party B.
• Replace the handset of your phone.
To know the call transfer result, remain Off-hook after dialing the transfer target’s number (party B).
• If the transfer is successful, you will get a confirmation tone for 3 seconds followed by error tone.
• If the transfer has failed, you will get error tone for two seconds and will be connected to the transfer target (party B), if available. If the transfer target has disconnected the call, you will be connected to the transferee.
• If the transfer has timed out, you will get continuous error tone.
108 Matrix SETU ATA211G System Manual
Call Toggle
Call Toggle allows you to have two simultaneous telephone conversations, talking to two persons alternately.
The parties for Call Toggle can be:
• Two outgoing calls
• Two incoming calls
• One outgoing call and one incoming call.
To use this feature, make sure that Call Toggle is enabled in the Class of Service of the FXS port. See
topic.
Using Call Toggle
• You are in speech with A and you want to talk to B.
• Dial Flash, A is put on hold. You get feature tone.
• Dial the number of B. When B answers the call, you are in speech with B.
• To talk to A, dial Flash-#4.
• You are in speech with A and B is put on hold.
• To talk to B, dial Flash-#4 again.
• You are in speech with B. A is put on hold.
• This way, you can talk alternately to A and B, by dialing Flash-#4 again.
When toggling between calls, you can disconnect the call you are currently in speech with by going Onhook.
Matrix SETU ATA211G System Manual 109
Call Waiting
When your phone is busy, the Call Waiting feature notifies you about another incoming call in the form of beeps.
The Call Waiting feature of SETU ATA211G allows you to:
• reject the waiting call.
• hold the current call and attend to the waiting call.
• disconnect the current call and attend to the waiting call.
Configuring Call Waiting
To use this feature, make sure that the Call Waiting feature is enabled in the Class of Service of the FXS port. See
topic.
Using Jeeves
To configure Call Waiting from the Admin mode:
1.
Log in as Admin.
2.
Click the Supplementary Services link on the left pane to expand.
3.
Click Supplementary Features.
110
4.
Keep the Enable Call Waiting check box enabled.
5.
Click Submit to save the settings.
6.
You may log out.
Matrix SETU ATA211G System Manual
To configure Call Waiting from the User mode:
1.
Log in as User.
2.
Click the User Settings link.
3.
Click the Supplementary Features link.
4.
Keep the Enable Call Waiting check box enabled.
5.
Click Submit to save the settings.
6.
You may log out.
Using Commands
• Lift handset.
• Dial #19-Admin Password (default: 1234).
OR
• Dial #18-User Password (default: 1234).
• Dial 72-1-#* to enable.
• Dial 72-0-#* to disable.
• Replace handset.
Using Call Waiting
When call waiting is enabled and you are busy on a call with party A,
• You will hear beeps indicating another incoming call.
• You may choose to do any of the following:
• Reject the call, by dialing Flash-#3. The beeps will stop, you will remain in speech with party A.
OR
• put party A on hold, by dialing Flash-#4. The beeps will stop, you will be in speech with party B.
Matrix SETU ATA211G System Manual 111
OR
• disconnect your call with party A, by dialing Flash-#5 and answer the waiting call. The beeps will stop, you will be in speech with party B. Party A will be disconnected.
112 Matrix SETU ATA211G System Manual
Conference
Three-party Conference, also referred to as Three-Way Calling, is a telephone call, in which you can have two other persons participate in the call.
You can initiate a conference by calling the first person, and then put the first person on hold to call the second person. You can also include another person when you in the middle of speech with a person.
The parties to a conference can be:
• Two outgoing calls
• Two incoming calls
• One outgoing call and one incoming call.
• While initiating the conference, the SETU ATA211G supports the Vocoder G.711 (Mu-law) only.
• To use this feature, make sure that the Conference feature is enabled in the Class of Service of the
topic.
Using Conference
• Lift handset.
• Dial the number of party A.
• When A answers the call, dial Flash.
• Party A is put on hold, and you will hear feature tone.
• Now, dial the number of party B.
• When B answers the call and you are in speech with B, dial Flash-#2.
• Three-way speech will be established between you, party A and party B.
• Replace the handset at the end of your conversation.
• The conference will be terminated.
You can convert a 3-Party Conference to Call Toggle by dialing the Call Toggle access code Flash-#4.
You will be connected to one party and the other party is put on hold.
Matrix SETU ATA211G System Manual 113
Do-Not-Disturb
If you do not want to receive any calls on your phone, you may set the Do-Not-Disturb feature on your phone. When you set DND, all incoming calls on your phone will be rejected, but you can continue to make outgoing calls.
Configuring Do-Not-Disturb
To use this feature, make sure that Do Not Disturb feature is enabled in the Class of Service of the FXS port. See
topic.
Using Jeeves
To set or cancel DND from Admin mode,
1.
Log in as Admin.
2.
Click the Supplementary Services link on the left pane to expand.
3.
Click Supplementary Features link.
4.
To set DND, select the Do-Not-Disturb check box. Default: Disabled.
To cancel, clear the check box.
5.
Click Submit to save.
To set or cancel DND from User mode,
1.
Log in as User.
114 Matrix SETU ATA211G System Manual
2.
Click the Supplementary Features link, under User Settings on the left pane.
3.
To set DND, select the Do-Not-Disturb check box. Default: Disabled.
To cancel, clear the check box.
4.
Click Submit to save.
Using Phone
• Lift handset of your phone.
• Dial #19-Admin Password (default: 1234).
OR
• Dial #18-User Password (default: 234).
• Dial 61-1-#* to set.
• Dial 61-0-#* to cancel.
• Replace handset.
Matrix SETU ATA211G System Manual 115
Call Forward
When you are away from your phone
11
, but would like to answer your calls, you can use the Call Forward feature to have SETU ATA211G forward incoming calls to another number.
SETU ATA211G supports the following Call Forward options, which you can set on your phone:
• Call Forward-Unconditional: All incoming calls received on the SIP Trunk are forwarded to the desired destination number, automatically without waiting for a response from your phone.
• Call Forward- Busy: All incoming calls received on the SIP Trunk are forwarded to the destination number, when your phone is busy.
• Call Forward- No Reply: All incoming calls received on the SIP Trunk are forwarded to the destination number, when you do not answer your phone.
When you set Call Forward-No Reply, SETU ATA211G waits for the duration of the Call Forward-No
Reply Timer for the phone to answer. This timer is configurable, and is set to 45 seconds as default.
If the phone does not answer before the timer expires, SETU ATA211G considers it as No Reply and forwards it to the desired destination number.
You can set a different destination number for each Call Forward option.
Configuring Call Forward
To use this feature, make sure
• you have selected Incoming Call Routing for the SIP Trunk as Route to FXS. See
• Call Forward feature is enabled in the Class of Service of the FXS port. See “FXS Port”
topic.
Using Jeeves
To use Call Forward from Admin mode,
1.
Log in as Admin.
2.
Click the Supplementary Services link on the left pane to expand.
3.
Click the Supplementary Features link.
11. Connected to the FXS port of SETU ATA211G.
116 Matrix SETU ATA211G System Manual
4.
Select the check box for the Call Forward option you want to set:
• Call Forward-Unconditional
• Call Forward-Busy
• Call Forward-No Reply.
In the corresponding box enter the desired destination number (up to 40 characters) you want the calls to be forwarded to.
5.
If you selected Call Forward- No Reply, you may also change the duration of the no-reply Timer, if required. The range of the Call Forward No-Reply Timer is 01 to 99 seconds. Default: 45 seconds.
6.
Click Submit to save.
To use Call Forward from User mode,
1.
Log in as User.
2.
Click the Supplementary Features link under User Settings on the left pane.
3.
Select the check box for the Call Forward option you want to set:
• Call Forward-Unconditional
• Call Forward-Busy
Matrix SETU ATA211G System Manual 117
• Call Forward-No Reply.
In the corresponding box enter the desired destination number (up to 40 characters) you want the calls to be forwarded to.
4.
If you selected Call Forward- No Reply, you may also change the duration of the no-reply Timer, if required. The range of the Call Forward No-Reply Timer is 01 to 99 seconds. Default: 45 seconds.
5.
Click Submit to save.
Using Phone
Call Forward Un-conditional
To configure destination number for Call Forward-Unconditional:
• Lift the handset of your phone.
• Dial #19-Admin Password (default:1234)
OR
• Dial #18-User Password (default:1234)
• Dial 51-Destination Number-#*
• Replace handset.
To set/cancel Call Forward-Unconditional:
• Lift the handset of your phone.
• Dial #19-Admin Password (default:1234)
OR
• Dial #18-User Password (default:1234)
• Dial 52-1-#* to set.
• Dial 52-0-#* to cancel.
• Replace handset.
Call Forward-Busy
To configure destination number for Call Forward-Busy:
• Lift the handset of your phone.
• Dial #19-Admin Password (default: 1234)
OR
• Dial #18-User Password (default: 1234)
• Dial 53-Destination Number-#*.
• Replace handset.
To set/cancel Call Forward- Busy:
• Lift the handset of your phone.
• Dial #19-Admin Password (default:1234)
OR
• Dial #18-User Password (default:1234)
• Dial 54-1-#* to set.
• Dial 54-0-#* to cancel.
• Replace handset.
118 Matrix SETU ATA211G System Manual
Call Forward- No Reply
To configure destination number for Call Forward- No Reply:
• Lift the handset of your phone.
• Dial #19-Admin Password (default: 1234)
OR
• Dial #18-User Password (default: 1234)
• Dial 55-Destination Number-#*.
• Replace handset.
To set the Timer for Call Forward-No Reply:
• Lift handset of your phone.
• Dial #19-Admin Password (default: 1234)
OR
• Dial #18-User Password (default: 1234)
• Dial 57-Time-#*. Valid range of the Timer is 01-99 seconds.
• Replace handset.
To set/cancel Call Forward-No Reply:
• Lift the handset of your phone.
• Dial #19-Admin Password (default:1234)
OR
• Dial #18-User Password (default:1234)
• Dial 56-1-#* to set.
• Dial 56-1-#* to cancel.
• Replace handset.
Matrix SETU ATA211G System Manual 119
Caller ID Restriction
If you do not want your caller ID to be displayed to the called party, you can do so using this feature.
Configuring Caller ID Restriction
Using Jeeves
120
1.
Log in as Admin with your Password.
2.
Click the Basic Settings link on the left pane to expand.
3.
Click SIP to open the SIP trunk parameters page.
4.
Select the desired SIP Trunk by clicking the SIP trunk number tab.
5.
Click More button to view all parameters on the page.
6.
Scroll to Advanced.
7.
Enable CLIR to hide your Caller ID. Default: Disabled.
8.
Click Submit to save.
Matrix SETU ATA211G System Manual
Using Commands
• Lift handset.
• Dial #19-Admin Password (default: 1234).
• Dial 66-SIP Trunk Number -Code-#*
Where,
SIP Trunk Number is
1 for SIP Trunk 1
2 for SIP Trunk 2
3 for SIP Trunk 3
Code is
1 to Enable CLIR
0 to Disable CLIR
• Replace handset.
Matrix SETU ATA211G System Manual 121
Selective SIP Trunk Access
Regardless of the SIP Trunk you have selected for 'Outgoing Call Routing', you can make outgoing calls from any
SIP Trunk by dialing the Access Code for that trunk.
1.
To dial a number from SIP1:
• Lift the handset of your phone.
• Dial #84.
• Dial the desired number.
• Talk, when the remote party answers the call.
2.
To dial a number from SIP2:
• Lift the handset of your phone.
• Dial #85.
• Dial the desired number.
• Talk, when the remote party answers the call.
3.
To dial a number from SIP3:
• Lift the handset of your phone.
• Dial #86.
• Dial the desired number.
• Talk, when the remote party answers the call.
122 Matrix SETU ATA211G System Manual
Speed Dialing
As the name itself suggests, this feature offers you a quick way to dial a number. Using this feature, you can make an outgoing call to a particular number by dialing a short code instead of dialing the entire number string.
Speed Dialing feature works on the basis of the Speed Dialing Table, which you must configure seperately for each port.
The Speed Dialing Table consists of Index Numbers that serve as short codes. You must assign contact numbers
(along with their names) that you want to speed dial against the Index numbers in the table and select the
Destination Route through which the number should be dialed out.
Using Speed Dialing from the FXS port,
• Lift the handset.
• Dial the feature access code for Speed Dial (#9) followed by the Index Number.
• SETU ATA211G will check the FXS Speed Dialing Table to fetch the number configured for the Index number and the corresponding destination Destination trunk (SIP1 / SIP2 / SIP3 / Mobile) to dial out the number.
If you want to use Speed Dialing from the SIP Trunk,
• If you dial the SIP Trunk number of ATA211G.
• ATA will answer the call and then you can dial the feature access code for Speed Dial (#9) followed by the
Index Number.
• SETU ATA211G will check the SIP Speed Dialing Table to fetch the number configured for the Index number.
• This number will be out dilaled from the Mobile port.
This feature will work on the SIP Trunk, only if Incoming Call Routing option is selected as Answer the
call, Collect number and route to Mobile. See
topic.
In the Number field, if you enter:
• SIP ID, the Destination trunk configured can be a peer-to-peer or proxy SIP trunk.
• IP Address / SIP URI, the Destination trunk must be can a peer-to-peer SIP trunk only.
If you want to use Speed Dialing from the Mobile port,
• Dial the Mobile port number of ATA211G.
• ATA will answer the call and then you can dial the feature access code for Speed Dial (#9) followed by the
Index Number.
• SETU ATA211G will check the Mobile Speed Dialing Table to fetch the number configured for the Index number and the corresponding Destination trunk (SIP1 / SIP2 / SIP3) to dial out the number.
This feature will work on the Mobile port, only if Incoming Call Routing option is selected is:
• Answer the call, collect number & route as per incoming call route selection.
• Route to FXS. If not answered within ring timer, answer the call, collect number & route as per incoming call route selection.
Matrix SETU ATA211G System Manual 123
Configuring Speed Dialing
To use Speed Dialing you must configure the Speed Dialing Table seperately for each port: FXS, Mobile and SIP.
Speed Dialing on the FXS Port
From Admin mode:
1.
Log in as Admin.
2.
Click the Supplementary Services link on the left pane to expand.
3.
Click Speed Dialing link to open the page. The Speed Dialing Table appears on this page.
You can program up to 20 entries in this Table from Index 01 to 20.
Against each index number:
• Enter the Name (Max 24 characters) of the contact you wish to speed dial.
• Enter the Number (Max. 40 characters) against each name.
• Select the appropriate Destination Route, through which you want the system to dial out the number.
4.
Click Submit to save your entries.
124 Matrix SETU ATA211G System Manual
From User mode:
1.
Log in as User.
2.
Click the Speed Dialing link. The Speed Dialing Table opens.
3.
To configure the Speed Dialing Table, follow the same instructions as provided for configuring the table from the Admin mode.
Speed Dialing on the Mobile Port
From Admin mode:
1.
Log in as Admin.
2.
Click the Supplementary Services link on the left pane to expand.
3.
Click Speed Dialing link to open the page. The Speed Dialing Table appears on this page.
You can program up to 20 entries in this Table from Index 01 to 20.
Matrix SETU ATA211G System Manual 125
Against each index number:
• Enter the Name (Max 24 characters) of the contact you wish to speed dial.
• Enter the Number (Max. 40 characters) against each name.
• Select the appropriate Destination Route, through which you want the system to dial out the number.
You may select: SIP1 or SIP2 or SIP3. Default: SIP1.
4.
Click Submit to save your entries.
From User mode:
1.
Log in as User.
2.
Click the Speed Dialing link. The Speed Dialing Table opens.
126 Matrix SETU ATA211G System Manual
3.
To configure the Speed Dialing Table, follow the same instructions as provided for configuring this table from the Admin mode.
Speed Dialing on the SIP Trunk
From Admin mode:
1.
Log in as Admin.
2.
Click the Supplementary Services link on the left pane to expand.
3.
Click Speed Dialing link to open the page. The Speed Dialing Table appears on this page.
You can program up to 20 entries in this Table from Index 01 to 20.
Matrix SETU ATA211G System Manual 127
Against each index number:
• Enter the Name (Max 24 characters) of the contact you wish to speed dial.
• Enter the Number (Max. 40 characters) against each name.
• For each number and name you enter, the system will dial out the number through the Mobile port.
4.
Click Submit to save your entries.
From User mode:
1.
Log in as User.
2.
Click the Speed Dialing link. The Speed Dialing Table opens.
128 Matrix SETU ATA211G System Manual
3.
To configure the Speed Dialing Table, follow the same instructions as provided for configuring this table from the Admin mode.
Matrix SETU ATA211G System Manual 129
Supplementary Services of Service Provider
When SETU ATA211G interfaced with a service provider server - ITSP, an ATA, the Matrix ETERNITY IP-PBX, or any other PBX - that supports supplementary services that require dialing of Flash
12
, like Call Hold, Call Transfer,
Call Waiting, etc., you may choose to access the features of the service provider, or to access the features of SETU
ATA211G primarily.
If you want to use the features of the service provider, you must select Network as the Subscriber Type for the FXS port of SETU ATA211G.
If you want to use the features of SETU ATA211G, you must select Gateway as the Subscriber Type for the FXS port of SETU ATA211G. However, you will be able to access the features of the service provider in the Gateway mode, by dialing Flash, followed by #0, the Access Code for Using Supplementary Services of Service Provider.
When the SETU ATA211G is set in the Gateway mode, when you dial flash and the access code #0 to access the supplementary services of the service provider, the active call will be put on hold and you will get a feature tone.
SETU ATA211G will start the an internal timer, called the Service Provider Access Code Wait Timer. This timer has a duration of 10 seconds. Any activity performed on the FXS port within this timer will be sent to the service provider server. Any activity performed on the FXS port after the expiry of this timer, will be processed by SETU
ATA211G.
To use Supplementary Services of Service Provider, configure the parameter Subscriber Type on the
FXS port as Network or as Gateway. See
Using Supplementary Services of Service Provider
If you have set SETU ATA211G in the Network Mode
• Dial Flash during speech.
You will get feature tone played by your service provider.
• Dial feature access code provided by the service providers server.
If you have set SETU ATA211G in the Gateway Mode
• Dial Flash during speech. This will place the active call on hold and you will get a feature tone.
• Dial #0.
You will be in Network mode for 10 seconds.
• Dial the feature access code provided by the service providers server within 10 seconds.
12.
To be able to use features of the service provider SETU ATA211G supports dialing of Flash during speech on SIP.
130 Matrix SETU ATA211G System Manual
Multi Stage Dialing
Multi-stage Dialing is useful when SETU ATA211G connected to a SIP Server being used for networking the PBXs of multiple sites. The extension users of the networked PBXs can dial the entire number string, both the destination number and the extension number of the destination PBX together. The SETU ATA211G will split the string into two stages. It will dial out the destination number first, and on receiving the answering signal from the PBX, it will dial the extension number. Thus, extension users of all the networked PBXs can call each other, without hassle.
Let us understand this with the help of an example.
• An organization has multiple offices across the globe: Canada, Australia, India and China. They require voice over IP network connectivity for inter-branch calling.
• At each office site, the existing voice infrastructure includes a PCM/ TDM PBX that does not support VoIP connectivity.
• So, to network the PBXs of the branch offices,
• SETU ATA211G is interfaced with the existing PCM/ TDM PBX at each country office for VoIP connectivity.
• At the Head Office, an IP PBX is installed, connected to the public IP network.
• The SETU ATA211G installed at the branch offices are registered with the IP PBX at the head office..
101
102
103
104
FXS1
PBX1
FXO1
FXS2
FXS3
FXS4
FXO2
FXOn
FXS
PSTN
ATA1
21
IP
PSTN
IP
22
ATA2
FXS
FXO1
PBX2
FXS1
FXO2
FXS2
FXS3
FXS4
FXOn
101
102
103
104
101
102
103
104
FXS1
PBX3
FXO1
FXS2
FXS3
FXS4
FXOn-1
FXOn
FXS
ATA3
PSTN
23
IP
IP PBX
ATA1 - 21
ATA2 - 22
ATA3 - 23
ATA4 - 24
IP
24
ATA4
PSTN
FXS
FXO1
PBX4
FXS1
FXOn-1
FXS2
FXS3
FXS4
FXOn
101
102
103
104
• At the Canada office, PBX1 is interfaced with SETU ATA211G, which is assigned the SIP ID 21.
• At the Australia office, PBX2 is interfaced with SETU ATA211G, which is assigned SIP ID 22.
Matrix SETU ATA211G System Manual 131
• At the India office, PBX3 is interfaced with SETU ATA211G, which is assigned SIP ID 23.
• At the China office, PBX4 is interfaced with SETU ATA211G, which is assigned a SIP ID 24.
• Now, from the office in Canada, where PBX1 is installed, the extension user 101 of PBX1 wants to call extension 102 of PBX2 in Australia. This is how it would work in absence of Multi-stage Dialing:
• Extension user 101 of PBX1 dials the access code for a trunk line, followed by the number 22, which is the SIP ID assigned to SETU ATA211G installed in Australia, and then the extension number 102. The
PBX1 routes this call to its FXO port which is connected to the FXS port of SETU ATA - 21.
• SETU ATA - 21, then routes this call to IP-PBX, which is further routed by the IP-PBX to SETU ATA -
22.
• SETU ATA - 22 places the incoming call on its FXS port as per incoming call logic. PBX2 is connected to the FXS port of SETU ATA -22.
• PBX2 receives the incoming call. PBX2 has Auto-Attendant or Direct Inward Dialing enabled on the landing trunk to answer the call on its FXO port.
• Answer Signal is detected by SETU ATA -21.
• PBX2 plays dial message/dial tone.
• The caller (Extension 101 of PBX1) then dials 102, the desired called party number. PBX2 places the call to its extension,102.
Thus, to make a call to an extension of another office, extension users need to dial the number in two stages, each time, to reach the extension of the other office. In the first stage, the calling extension user dials the SIP ID of SETU
ATA. In the second stage, the calling extension user dials the desired extension number.
When Multi-Stage Dialing is used, extension users need to dial only the complete number string in one stage, and
SETU ATA211G converts the dialing method automatically into two stages.
To take the above example further, when Multi-Stage Dialing is used this is how it would work,
• SETU ATA -21 (at calling end) accepts the complete number—trunk access code + SIP ID of ATA in
Australia + extention number 102—dialed by the extension user.
• It dials only the number of the remote SIP device, which is SETU ATA - 22 (at called side).
• When the call matures, SETU ATA - 21 (at calling end) then sends the remaining numbers - 102 - in DTMF to the called device, SETU ATA -22.
• While SETU ATA - 21 is sending the DTMF (102, the actual destination number which is the extension of called PBX 2), the caller (extension 101 of PBX1) will hear the routing tone, if the Play Routing Tone flag is enabled in the System Parameters of ATA - 21.
132 Matrix SETU ATA211G System Manual
Configuring Multi-Stage Dialing
For this feature to work, at each site where the SETU ATA211G is installed, do the following:
• Make sure that Auto Attendant or Direct Inward Dialing is enabled on the FXO port of the PBX on which
SETU ATA211G is interfaced.
• Enable Automatic Number Translation on the desired SIP Trunk of SETU ATA211G.
• Configure the Automatic Number Translation Table.
• Set the DTMF ON Time, DTMF OFF Time.
• Enable ‘Play Routing Tone’ in the System Parameters, if required.
• Set the Pause Timer to the desired value.
To configure Multistage Dialing at each site where the SETU ATA211G is connected,
• Open Jeeves.
• Log in as Admin with your password.
• Click the Basic Settings link.
• Under Basic Settings, click SIP.
• Now, click the SIP Trunk number tab (SIP Trunk 1, 2, or 3) on which you want to apply Multi-stage Dialing.
• Click the More button to view all parameters on this page.
• Scroll to Advanced.
• Enable Automatic Number Translation on this SIP Trunk.
• To configure the Automatic Number Translation Table, click the arrow icon.
The Automatic Number Translation Table opens in a new window.
Matrix SETU ATA211G System Manual 133
134
The Automatic Number Translation Table can accommodate upto 24 Dialed Numbers and their corresponding Substitute Numbers, which are stored against Index numbers 01 to 24.
In the Dialed Number column, enter the numbers that users will dial out using the SIP trunk.
In the Substitute Number column, enter the number which the system should dial out in place of the number dialed by the users.
The SETU ATA211G considers the character '~' as Wait for Answer and it considers the character '^' as
Pause.
You may use these characters in the Substitute Numbers, if you want SETU ATA211G to provide suitable delay.
Make sure you enter a Dialed Number and its corresponding Substitute Number at the same Index. For example, if you enter 22 as Dialed Number at Index 01, enter the Substitute Number 22~ also at Index 01.
To take the above example further, if extensions of PBX1 want to reach the extensions of PBX2 by dialing
22 + Extension Number (of PBX2), you must configure the Dialed Number and Substitute Number at calling side, i.e. SETU ATA - 21, as follows:
Index Dialed Number Substitute Number
01 22 22~
02
03
::
24
When any extension user of PBX1 dials '22 + Extension Number (of PBX2)', for example, 22101 (to reach the extension 101 of PBX2),
Matrix SETU ATA211G System Manual
• SETU ATA -21 will first dial out ‘22’, which is the SIP ID of the called ATA and wait for answer' (22~).
The caller will only hear routing tone.
• PBX2 on the called side answers the call (DID/Auto-Attendant must be enabled on the FXO port).
• When the call matures, SETU ATA - 21 will send the remaining numbers, 101 in the RFC 2833
(Outband) to the called device, SETU ATA - 22.
• These DTMF digits are then detected by PBX2 on its FXO port. The PBX places the call to extension
101.
• In the above scenario, if you want some delay after the call matures and before SETU ATA -21 sends the remaining DTMF digits, program '22~^' as Substitute Number instead of '22~'.
Index Dialed Number Substitute Number
01 22 22~^
02
03
::
24
• Click Submit to save your entries.
• Close the window.
• Keep the DTMF ON and DTMF OFF Time to default values, if you don't have any specific requirement.
• Change the Pause Timer to the desired value, if required. Default: 2 seconds.
• Click Submit to save your SIP Trunk settings.
• If you want Routing Tone to be played to the calling extension user, keep the Play Routing Tone flag enabled in the
page .
• You may log out of Jeeves or continue, as required.
The above example and configuration instructions are for Multi-stage Dialing on SIP trunks only. You may also configure Multi-stage Dialing on the Mobile port, if required.
Matrix SETU ATA211G System Manual 135
End of Dialing
Unlike a normal phone which transmits each digit you press to the telephone exchange for dialing, when you are making an VoIP call, you must enter all the digits/characters and indicate to SETU ATA211G the 'End of Dialing', i.e. that you have finished dialing.
SETU ATA211G considers End of Dialing when:
1.
The Termination Digit, # (non-programmable), is pressed after dialing the number/IP Address/SIP URI.
2.
The Inter Digit Wait Timer elapses, after which the system automatically dials out the number. By default the Inter Digit Timer in the system is set to 5 seconds. The system will wait for 5 seconds after the last digit is pressed, consider the number as complete and dial it out automatically.
To change the duration of the Inter Digit Wait Timer, see “System Parameters”.
3.
The number of digits dialed from the phone connected to the FXS port matches with the length of the
Maximum Digits configured in the “Dialed Number Table” . Default: 16 digits.
When you dial a number from the phone connected to SETU ATA, the system will match it with the above end-ofdialing indications and accept the one that matches first.
If you do not want SETU ATA to wait for the Inter Digit Wait Timer to expire to dial out the number, you may dial the termination digit ‘#' after dialing the number string.
The system will consider the Maximum Digits configured as End-of-Dialing only
• when Route all calls as per Dialed Number Table is selected as Outgoing Call routing option for the
FXS port.
• when Dialed Number Table is selected as Incoming Call Route for the Mobile port.
136 Matrix SETU ATA211G System Manual
Mobile Network Selection
When SETU ATA211G is located in the home region, then, the SIM card gets registered with the Network Operator of that SIM only, leading to no extra charges to the user (i.e. no roaming charges). Whereas, if SETU ATA211G is located in an area away from the home region or in an area where there are more than one Network Operators are available, then, the SIM card may get registered with another available Network and result in roaming charges.
Thus, Mobile Network Selection feature of SETU ATA211G enables you to select the GSM network of your own choice, either automatically or manually. At Power ON, ATA211G will automatically locate and register the SIM with the Network that supports the SIM card installed in it. If the SIM fails to register, it will restart the process of network selection on the expiry of the Network Registration Retry Timer.
Types of Network Selection Mode
SETU ATA211G gives you the flexibility to select network selection mode as per your requirement. ATA211G supports two modes of network selection: Automatic and Manual. Before you enable the Manual mode for
Network Selection, Network Operator Table is configured, consisting of Network Operator Codes and its priority.
Automatic
This mode is selected when you require that your mobile station should always get registered with the available
GSM network whether you are in home region or outside the home region, to make and receive calls at any cost.
• In Automatic mode, mobile port gets registered with any available network whose signal strength is more compared to other available networks.
Manual
This mode is selected when you always wish to get registered with the local network operator available in the region.
• If ATA211G is installed in the border area where more than one GSM network operator is available and network selection mode is set to automatic then it may happen that the SIM is registered with the other region's network operator. This is undesirable. Hence, in this situation, Manual mode of network selection is selected.
If you select the Mobile Network Selection as Manual,you must configure Network Operator Codes
(MCC and MNC) according to priority you want to assign to each, from Priority 1 to Priority 9.
With Network Operator Codes (MCC and MNC) configured according to their priority, at every Power on, ATA211G will send a request for available GSM Network Operators, who in turn will respond to the request with a list of available Network Operator Codes. ATA211G will match the available Network
Operator Codes with those you configured and select the Network Operator which best suits your requirement in order of priority.
• If the Mobile Port fails to register, it will restart the process of network selection on the expiry of the
Network Registration Retry Timer.
• If no match is found, the SIM will not get registered with any of the available Network Operators and no calls can be made or received on this port.
Matrix SETU ATA211G System Manual 137
About Network Operator Codes
Network Operator Codes comprises of MCC (Mobile Country Code) appended by MNC (Mobile Network Code).
• MCC: It identifies a country and a country may be assigned more than one MCC. For example, MCC assigned to India is 404 which is same for all the network operators in India. MCCs are generally of 3 digits.
• MNC: It is a Mobile Network Code and is generally of 2-3 digits.
The MCC-MNC combination uniquely identifies the home network of the mobile terminal or mobile user.
MNC are different in each state for same network operator. For example, Airtel, a GSM network operator in
India has different MNC assigned to its networks in various states. The MNC for Airtel in Maharashtra state is 90, whereas, the same for the Gujarat state is 98.
To set Network Selection Mode, see “Mobile Port”.
138 Matrix SETU ATA211G System Manual
Return Call to Original Caller (RCOC)
When an outgoing call made from SETU ATA211G is returned by the called party, the call lands on the port from which the call was made. The call is then routed according to the incoming call route selection configured in SETU
ATA211G. Now, it is desirable that the returned call be routed to the port that originally made the call. However, if the port that originally made the call is not configured as the destination for incoming call routing, the returned call will be routed to a different port instead of the port that originally made the call.
With the Return Call to Original Caller (RCOC) feature, regardless of the incoming call route selection configured in the system, it is possible to route the call returned by the called party directly to the same port from which the call was originally made.
How it works?
For this feature to work, it must be enabled on the desired port(s), i.e. the Mobile Port, SIP Trunks.
SETU ATA211G supports three types of RCOC:
1.
RCOC - On Busy: When an outgoing call is made from SETU ATA211G, RCOC is set when the called party is found to be busy.
2.
RCOC - On Speech: When an outgoing call is made from SETU ATA211G, RCOC is set when the called party answers the call.
3.
RCOC - On No Reply: When an outgoing call is made from SETU ATA211G, RCOC is set when the called party does not answer the call.
You can enable any or all three types of RCOC on the Mobile port and SIP trunks.
Here is an example of how this feature works:
• An outgoing call is made from the FXS port (Source Port) of SETU ATA211G.
• The system checks the Outgoing Call Route, and finds the Mobile port as the Destination Port.
• The system checks for the type of RCOC enabled on the Mobile port (Destination Port).
• If RCOC-On Busy is enabled,
• If the called party is found busy, the system stores the record of the outgoing call in an internal database referred to as the RCOC Table.
• If RCOC-On Speech is enabled,
• when the called party answers the call, the system stores the record of the outgoing call in the RCOC
Table.
• If RCOC-No Reply is enabled,
• when there is no response from called party, the system stores the record of the outgoing call in the
RCOC Table.
• The system stores the following details of the outgoing call in the RCOC Table:
Matrix SETU ATA211G System Manual 139
• Calling Party Number: The number received on the Source Port. In this example, it is the number configured for the FXS port.
• Called Party Number: The number received in the destination port (Mobile Port/SIP Trunk) from the
Source Port. In this example, it is the number dialed from the FXS port and received on the Mobile Port.
• Source Port Type and Port Number: The number of the Source port from which the outgoing call was originally made. In this example, the FXS port.
The RCOC Table can store up to 200 such entries.
• The system stores the details of each outgoing call for the duration of the RCOC Delete Record Timer, which is configurable. By default, the Timer is set to 999 minutes. On the expiry of this Timer, the details are deleted.
• Now, when there is an incoming call on the Mobile port/SIP trunk on which RCOC is enabled, the system matches the CLI of the incoming call with the RCOC Table.
• For example, if incoming call is received on the Mobile port, then, CLI received on Mobile Port is checked with the Called Party Number stored in the RCOC table.
The system uses the best match found logic. It matches 7 digits of the CLI number with the digits of the
Called Party Number, from the right hand side. For example: +919824284984 is stored in the RCOC table, the incoming CLI is 9824284984, the system will match 7 digits from the right hand side 4284984 to arrive at the best match.
• When a match is found, the system checks the corresponding Calling Party Number and Source port stored for the Called Party Number stored in the RCOC Table, and routes the call to the Source port, i.e. from which the call was originally made.
• The system clears the record of this call from the RCOC Table.
• If no match is found in the RCOC Table, the call will be routed according to the Incoming Call Route selection configured in the system.
• If the RCOC Record Delete Timer has expired when the call is returned, the call will be routed as per the Incoming Call Route selection, because no matching record exists in the RCOC Table.
• Records of outgoing calls made using the features Call Transfer-Blind, Call Transfer-Attended, and Call
Forward, will not be stored in the RCOC table.
• The RCOC Table can store records of 200 outgoing calls. You can delete all the entries in the table, any time you want.
Configuring RCOC feature
1.
Log in as an Admin.
2.
Click Basic Settings to expand.
140 Matrix SETU ATA211G System Manual
3.
Click Mobile link or SIP link as per your requirement to enable RCOC feature on these ports.
4.
Now, select the type of RCOC you want to enable on the Mobile Port/SIP Trunk.
On Busy:
• Select the Enable check box if you want the returned call to be routed to the original port if the called party is found to be busy.
On No Response:
• Select the Enable check box if you want the returned call to be routed to the original port if the called party does not answer the call.
On Speech:
• Select the Enable check box if you want the returned call to be routed to the original port if the called party answers the call.
5.
Click Submit to save.
Matrix SETU ATA211G System Manual 141
6.
Now, to configure RCOC Record Delete Timer, click System link under Advance Settings link.
142
RCOC Record Delete Timer:
• In RCOC Record Delete Timer field, enter the time (in minutes) after which the entry stored in RCOC
Table should be deleted automatically.
RCOC Record Delete Timer starts as soon as the called party is found busy, or is not responding, or answers the call (depending on the type of RCOC set) and the system stores the record of the outgoing call in the RCOC Table.
After the expiry of RCOC Record Delete Timer, the entry stored in the database is deleted automatically by the system. The range of this timer is 001 - 999 minutes. By default, it is set to 999 minutes.
• Clear RCOC Table: Click this button, whenever you want all the entries of the RCOC table to be cleared.
7.
Click Submit button to save.
Matrix SETU ATA211G System Manual
CHAPTER 7
System Status
You may view the status of the System, the Network ports (LAN and WAN), SIP Trunks and Auto Configuration from Jeeves.
You can also check the status of certain parameters, like the Registration status of SIP Trunks, IP Address and
Subnet Mask of the LAN and WAN port, on the display of the Phone connected to FXS port by dialing the relevant
Viewing System Status from Jeeves
To view System Status on Jeeves from Admin Mode,
• Log in as Admin.
• Click the Status link to open the page.
Matrix SETU ATA211G System Manual 143
To view System Status on Jeeves from User Mode,
• Log in as User.
• Click Status link to open the page.
SIP
The following parameters will be displayed for SIP Trunks 1, 2 and 3.
• Status: In this field, different status messages may be displayed, each of which are described briefly in the table below.
Status
Disable
Registering
Active
Failed
Description
Shows that SIP Trunk is disabled.
Shows that SIP Trunk is enabled and is waiting for response from the SIP server.
Shows that SIP Trunk is registered with the SIP server.
Shows that some error has occurred in the SIP Trunk and no calls can be made using it (applicable only in case of Proxy Account).
• Registration Time: The SIP Trunk is registered with the Registrar Server for a particular time period, after which it has to be re-registered. The registrar server indicates the time remaining for re-registration of the
SIP Trunk. The same time is displayed in this field.
144 Matrix SETU ATA211G System Manual
• Registration Retry Count: This field displays the total number of register messages which have been sent to the registrar server for registering SIP Trunk.
• Reg. Last Failed Reason: This field displays the reason for failure of SIP Trunk registration with the registrar server. The different reasons for registration failure that may appear in this field are:
Reason for Failure
Message send fail
Failed to create Register client
Failed to detach register client
Failed to send request
Local Failure
Response time-out
Error Response- 4xx to 6xx
No contact header in 2xx
Description
This reason is displayed when registration request sent to registrar server fails.
This reason is displayed when SIP stack has memory constraint/ resource limitation/ the number of SIP clients to register is greater than the number programmed in the stack.
This reason is displayed when SIP stack has memory constraint/ resource limitation/ the number of SIP clients to register is greater than the number programmed in the stack.
This reason is displayed when DNS server is not programmed.
This reason is displayed when DNS query fails.
This reason is displayed on the expiry of the General Request Timer.
This is error response code.
This reason is displayed when no contact address is received in 2xx response from the SIP server.
Authentication Failed This reason is displayed when the SIP server does not authenticate
SETU ATA.
STUN address is not programmed This reason is displayed when STUN is enabled but address is not configured.
STUN query fail
Outbound address is not programmed
Router's IP address is not programmed
This reason is displayed when a query to the STUN server fails.
This reason is displayed when Outbound is enabled but Outbound address is not configured.
This reason is displayed when Router's IP Address is to be used in signaling but the address is not programmed.
Mobile
Matrix SETU ATA211G System Manual 145
Following parameters will be displayed for the Mobile port.
• IMEI Number: This field displays the IMEI number
13
of the GSM network.
• Currently Registered With (Network Operator Code): This field displays the code of the currently registered network with which the Mobile Port is registered. If it is not registered with any of the network types then the system displays ‘not registered’ status. Default: Not Registered.
• Currently Registered With (Network Operator Name): This field displays the name of the network with which the Mobile Port is currently registered with.
• Signal Strength: This field displays the current signal strength.
• Activity Status: This field displays the below status of the port’s activity:
• Module Initialization
• SIM PUK Required
• SIM PIN Wrong
• SIM Absent
• SIM Present
• Network Absent
• Network Present
• Firmware Version of Engine: This field displays the current firmware’s version as well as revision of engine.
Network Parameters
Following status of network parameters (LAN and WAN) will be displayed on the Network page.
13. IMEI (International Mobile Equipment Identity) Number is a unique identity number of the GSM engine.
146 Matrix SETU ATA211G System Manual
LAN
• IP Address: This field displays the current IP Address of the LAN port.
• Subnet Mask: This field displays the current Subnet Mask Address of the LAN port.
• MAC Address: This field displays the MAC Address of the LAN port.
WAN
• Routing Mode: This field dispalys the Routing Mode selected, that is NAT or Bridge.
• IP Address: This field displays the current IP Address of the WAN port.
• Subnet Mask: This field displays the current Subnet Mask Address of the WAN port.
• Gateway Address: This field displays Gateway Address assigned to the WAN Port of SETU ATA211G.
This field displays the IP Address of the LAN port of the Router.
• Primary DNS Address: This field displays the Primary DNS address of SETU ATA211G.
• Secondary DNS Address: This field displays the Primary DNS address of SETU ATA211G.
• DNS Domain Name: This field displays the DNS Domain Name of SETU ATA211G.
• MAC Address: This field displays MAC Address of the WAN Port of SETU ATA211G.
• NAT Type: This field displays the NAT Type, if STUN is enabled in SETU ATA211G. Commonly used NAT types are:
• Unknown
• Open
• Conenat
• Restrictednat
• Portrestrictednat
• Symmetricnat
• Symmetricfirewall
• Blocked
• IP Address fetched using STUN: This field displays the IP address fetched using STUN, if STUN server address is configured.
• SIP Port fetched using STUN: This field displays the SIP port fetched using STUN if STUN server address is configured.
Matrix SETU ATA211G System Manual 147
System
Following status of System parameters are displayed on this page.
.
Date &Time
• Current Date: Current Date is displayed in this field.
• Current Time: Current Time is displayed in this field.
.
Firmware
• Version-Revision: Current Software Version-Revision of SETU ATA211G is displayed here.
• Kernel Date: The Date of current Kernel of the system is displayed here.
Auto Configuration
• Status: This field displays the type of Auto Configuration option selected.
• Next Resync: This field displays when the system will resync next for Auto Configuration.
• Last Resync: This field displays the time when the system last resynchronized with the Auto Configuration server.
You may log out of Jeeves.
148 Matrix SETU ATA211G System Manual
Viewing System Status on Phone
To view System Status on the phone’s display from Admin Mode,
• Lift the receiver of the phone.
• Dial #19.
• Dial the Admin Password (default: 1234).
To view System Status on phone’s display from User Mode,
• Lift the receiver of the phone.
• Dial #18.
• Dial the User Password (default: 1234).
You will get programming tone.
On entering Admin/User Mode,
• Dial the System Command for the status you want to view.
• You get confirmation tone.
• Go On-hook (replace the receiver of the phone) on confirmation tone.
• Your phone will ring.
• The status for the port or trunk for you dialed the command will be displayed on your phone.
For example:
To view the IP address of the WAN port,
Dial 31-#*
Go On-hook at the confirmation tone.
Your phone rings, and the IP Address will be displayed on your phone as: 192168001196
To view the WAN Subnet Mask,
Dial 33-#* and go On-hook at the confirmation tone.
Your phone rings and WAN Subnet Mask is displayed as: 255255255000
To view the IP address of LAN port,
Dial 32-#*
Go On-hook at the confirmation tone.
Your phone rings, and the IP Address of the LAN port is displayed as: 192168002021
To view the LAN Subnet Mask,
Dial 34-#* and go On-hook at the confirmation tone.
Your phone rings and the LAN Subnet mask is displayed as: 255255255000
To view the Gateway Address,
Matrix SETU ATA211G System Manual 149
Dial 35-#* and go On-hook at the confirmation tone.
Your phone rings and the Gateway Address is displayed as: 192168001254
To view DNS Address,
Dial 36-#* and go On-hook at the confirmation tone.
Your phone rings and the DNS Address is displayed as: 202100098054
To view the Connection Type,
Dial 37-#* and go On-hook at the confirmation tone.
If your connection type is DHCP, the phone will display 001
If your connection type is PPPoE, the phone will display 002
If your connection type is Static, the phone will display 003
To view the registration status of SIP Trunk,
Dial 38-SIP Trunk Number-#* and go On-hook at confirmation tone.
SIP Trunk Number is 1 for SIP Trunk1, 2 for SIP Trunk2 and 3 for SIP Trunk3
Your phone will ring and display one of the following:
001 for Disabled
002 for Registered
003 for Registering, when registration request is sent and the system is waiting for response
004 if the SIP trunk is configured as Peer-to-Peer Trunk.
005 if the registration request has failed, cannot be sent to the server.
Each time you go On-hook to view status of a port or trunk, you must enter the configuration mode again to view the status of another port or trunks.
150 Matrix SETU ATA211G System Manual
Appendix
Call Progress Tone Generation
Code Country
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
Australia
Argentina
Belgium
Brazil
China
Egypt
France
Germany
Greece
India
Korea
Malaysia
19 Mexico
20 New Zealand
21
22
23
24
25
26
27
28
29
30
31
Indonesia
Iran
Israel
Italy
Japan
Kenya
Philippines
Poland
Portugal
Russia
Saudi Arabia
Singapore
South Africa
Spain
Thailand
Turkey
UAE
425
425
400
425
400
425
425
425
425
425
425
425
Freq.
425*50
440
425
425
425
400*50
450
Dial Tone
Hz
425*25
425
425
425
450
400*25
350+440
425
425
400
400*33
350+440
Cadence second cont.
cont.
cont.
cont.
cont.
Ring Back Tone
Freq.
Cadence
Hz
400*25
425
425
425
450
425*50
440
425
425 second
0.4on 0.2off
0.4on 2.0off
1.0on 4.0 off
1.0on 3.0off
1.0on 4.0 off
1.0on 4.0off
Freq.
Busy Tone
Cadence
Hz
425 second
0.375on
0.375off
425
425
425
450
0.3on 0.2off
0.5on 0.5off
0.25on 0.25off
0.35 on
0.36off
2.0on 1.0off
425*50
1.5on 3.5off
440
1.0on 4.0off
1.0on 4.0off
425
425
1.0on 4.0off
0.5on 0.5off
0.48on 0.48off
0.3on 0.3off
Freq.
Hz
425
425
425
425
450
Error Tone1
Cadence second
0.375on 0.375off
0.3on 0.4off
0.167on 0.167off
0.25on 0.25 off
0.7on 0.7off
Error Tone2
Freq.
Hz
425
425
425
425
450
Cadence second
1on 1off
1on 1off
1on 1off
1on 1off
1on 1off cont.
cont.
cont.
0.2on 0.3off
0.7on 0.8off
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
cont.
450
440
425
425
0.5on 0.5off
0.25on 0.25off
0.24on 0.24off
0.15on 0.15off
450
440
425
425
1on 1off
1on 1off
1on 1off
1on 1off
400*25
425
425
400
425
400*20
425
0.4on 0.2off
0.4on 2.0off
1.0on 4.0off
1.0on 4.0off
1.0on 3.0off
1.0on 4.0off
1.0on 2.0off
0.67on 3.0off
1.5on 5.0off
400
425
425
400
425
400
425
0.75on 0.75off
400
425
425
400
425
400
425
0.25on 0.25off
0.25on 0.25off
0.25on 0.25off
0.25on 0.25off
0.2on 0.2off
0.25on 0.25off
0.2on 0.6off
400
425
425
400
425
400
425
1on 1off
1on 1off
1on 1off
1on 1off
1on 1off
1on 1off
1on 1off
440+480 1.0on 2.0off
480+620 0.5on 0.5off
480+620
425 0.4on 0.2off
0.4on 2.0off
425 0.5on 0.5off
425
425 1.0on 4.0off
400+450 0.4on 0.2off
0.4on 2.0off
425
400
0.25on 0.25off
0.5on 0.5off
425
400
0.3on 0.2off
0.5on 0.25off
0.25on 0.25off
0.25on 0.25off
480+620
425
425
400
1on 1off
1on 1off
1on 1off
1on 1off
425+480 1.0on 4.0off
480+620 0.5on 0.5off
480+620 0.25on 0.25off
480+620 1on 1off
425 1.0on 4.0off
425 0.5on 0.5off
425 0.5on 0.5off
425 1on 1off
425
425
1.0on 5.0off
0.8on 3.2off
425
425
0.5on 0.5off
0.4on 0.4off
450
425
0.33on 1.0off
0.25on 0.25off
450
425
1on 1off
1on 1off
425
425*24
1.2on 4.6off
0.4on 0.2off
0.4on 2.0off
425
425
0.5on 0.5off
0.75on 0.75off
425
425
0.25on 0.25off
0.25on 0.25off
425
425
1on 1off
1on 1off
400*33
425
400
450
400+450
0.4on 0.2off
0.4on 2.0off
1.5on 3.0off
1.0on 4.0off
2.0on 4.0off
0.4on 0.2off
0.4on 2.0off
400
425
400
450
400
0.5on 0.5off
0.5on 0.5off
0.5on 0.5off
0.5on 0.5off
0.5on 0.5off
0.2on 0.6off
0.2on 0.6off
0.5on 0.5off
0.2on 0.2off
0.5on 0.5off
0.5on 0.5off
0.375on
0.375off
400
425
400
450
400
0.25on 0.25off
0.25on 0.25off
0.3on 0.3off
0.2on 0.2off
0.6on 0.2off
0.4on 0.35off
0.225on 0.525off
400
425
400
450
400
1on 1off
1on 1off
1on 1off
1on 1off
1on 1off
Matrix SETU ATA211G System Manual 151
Code Country
01 Australia
02 Belgium
03 Brazil
04 China
05 Egypt
06 France
07 Germany
08 Greece
09 India
10 Israel
11 Italy
12 Japan
13 Korea
14 Malaysia
15 New Zealand
16 Poland
17 Portugal
18 Russia
19 Singapore
20 South Africa
21 Spain
22 Thailand
23 UAE
24 UK
25 USA/Canada
Code Country
32 UK
Freq.
Dial Tone
Cadence
Hz
350+440 second cont.
Ring Back Tone
Freq.
Cadence Freq.
Busy Tone
Cadence Freq.
Error Tone1
Cadence
Error Tone2
Freq.
Cadence
Hz second
400+450 0.4on 0.2off
0.4on 2.0off
Hz
400 second
0.375on
0.375off
Hz
400 second
0.4on 0.35off
0.225on 0.525off
Hz
400 second
1on 1off
440+480 2.0on 4.0off
480+620 0.5on 0.5off
480+620 0.25on 0.25off
480+620 1on 1off 33 USA/Canada 350+440 cont.
Note1:
Cont. = continuous
f1*f2: f1 is modulated by f2.
f1+f2: the juxtaposition of two freq. f1 and f2 without modulation.
Note 2:
The frequency and cadence for following tones are same and fixed for all countries:
• Confirmation Tone: 400Hz, 0.1 on - 0.1 off
• Programming Tone: 400Hz, 0.1 on - 0.9 off
• CCWT: 400Hz, 0.3 on 6.0 off
• Routing Tone: 400Hz, 0.1 on 1.9 off
Ring Cadences
Frequency
(Hz)
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
0.4
2.0
1.0
1.0
1.0
2.0
2.0
2.0
1.0
1.0
0.4
0.4
T1ON
0.4
1.0
1.0
1.0
2.0
1.5
3.5
1.0
1.5
2.0
2.0
0.4
2.0
0.2
3.0
4.0
2.0
3.0
3.0
3.0
3.0
5.0
3.0
0.2
0.2
CADENCE (In Seconds)
T1OFF
0.2
3.0
T2ON
0.4
T2OFF
2.0
4.0
3.0
4.0
3.5
5.5
4.0
0.79
1.1
3.0
3.0
3.0
0.2
4.0
0.4
0.4
2.0
0.4
0.4
2.0
2.0
2.0
152 Matrix SETU ATA211G System Manual
Code Country
01 Australia
02 Belgium
03 Brazil
04 China
05 Egypt
06 France
07 Germany
08 Greece
09 India
10 Israel
11 Italy
12 Japan
13 Korea
14 Malaysia
15 New Zealand
16 Poland
17 Portugal
18 Russia
19 Singapore
20 South Africa
21 Spain
22 Thailand
23 UAE
24 UK
25 USA/Canada
Frequency
(Hz)
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
3.5
1.0
0.4
2.0
1.0
1.0
1.0
2.0
2.0
2.0
1.0
1.0
0.4
0.4
1.5
2.0
2.0
0.4
2.0
T1ON
0.4
1.0
1.0
1.0
2.0
1.5
5.5
4.0
0.2
3.0
4.0
2.0
3.0
3.0
3.0
3.0
5.0
3.0
CADENCE (In Seconds)
T1OFF
0.2
3.0
T2ON T2OFF
0.4
2.0
4.0
3.0
4.0
3.5
0.2
0.2
3.0
3.0
3.0
0.2
4.0
0.79
1.1
0.4
2.0
0.4
0.4
2.0
2.0
0.4
2.0
Where,
T1ON, T1OFF, are ON and OFF period for first ring cadence and T2ON, T2OFF, are ON and OFF period for second ring cadence.
Waveform for 'ring', is Sine Wave.
Frequently Asked Questions (FAQs)
Q.1
Which internet telephony (VoIP) protocols are supported by ATA211G?
Ans.
ATA211G supports Session Initiation Protocol (SIP) to make/receive calls on the Internet.
Q.2
Can I make a call to another SIP terminal (e.g. Soft Phone running on PC) in my LAN network?
Ans.
Yes. You can make a call to any SIP terminal in your LAN just by dialing an IP address of the SIP terminal.
If you are not comfortable in dialing an IP address, you can use 'Peer to Peer' feature which allows you to dial the number instead an IP address for such type of applications.
Q.3
I have only one Internet connection for Internet surfing. Do I need another internet connection for making VoIP calls using ATA211G?
Ans.
No. You do not need another internet connection to use ATA211G. ATA211G has inbuilt router which enables you to surf internet and making VoIP calls at the same time.
Q.4
I am using the ATA211G to make VoIP calls and surf internet. I have connected my PC to LAN port
Matrix SETU ATA211G System Manual 153
of ATA211G. Can I still surf the internet when ATA211G is power down?
Ans.
No. You can not surf Internet if ATA211G is power down. You must power ON the ATA211G to enable
Internet surfing on your PC. Else, connect the PC directly to the internet.
Q.5
I am using the ATA211G to make VoIP calls and surf internet. I have connected my PC to LAN port of ATA211G. Can I still make VoIP calls when my PC is shut down or not connected?
Ans.
Yes. You can still make VoIP calls when your PC is shutdown or not connected.
Q.6
My Internet Service Provider (ISP) supports only PPPoE for internet services. Can I use ATA211G with my ISP?
Ans.
Yes. You need to configure PPPoE User-Id and PPPoE Password in ATA211G provided by your ISP.
Q.7
My internet Service Provider (ISP) supports only DHCP to provide internet services. Can I use
ATA211G with my ISP?
Ans.
Yes. You need to enable the DHCP client in ATA211G.
Q.8
My internet service provider (ISP) provides me only dynamic IP address. Can I use ATA211G to make VoIP calls and surf Internet at the same time?
Ans.
Yes. Enable DHCP or PPPoE client in ATA211G as used by your ISP to provide internet services.
Q.9
I do not have PC to access Web Jeeves for configuration. Can I change the IP address and subnet mask of LAN/ WAN port?
Ans.
Yes. You can change the IP address and subnet mask of LAN/ WAN port of ATA211G if you do not have
PC to access Web Jeeves. You need to issue commands from the FXS port to change the IP address and subnet mask.
Q.10
I do not have PC to access Web Jeeves for configuration. Can I change the internet connection type of ATA211G to DHCP or PPPoE or Static?
Ans.
Yes. You can change the connection type if you do not have PC to access Web Jeeves. You need to issue commands from the FXS port to change the connection type.
Q.11
I do not have PC to access Web Jeeves for configuration. Can I know whether ATA211G is registered with ITSP or not?
Ans.
Yes. You can know the status of your SIP registration using LED provided on the enclosure of ATA211G or by command to display registration status on the Phone connected to FXS port.
Q.12
I have connected my PC to LAN port of ATA211G. But, I am not able to access the Web Jeeves for configuration.
Ans.
Ensure that the IP address of LAN port of ATA211G and IP address of your computer should be in same subnet to enable Web Jeeves from your computer. If both the IP address is in the same subnet, check for any error in the Ethernet cable which connects your computer to LAN port of ATA211G.
Q.13
Can I upgrade my ATA211G for new firmware?
Ans.
Yes. You can upgrade the ATA211G for new firmware. To upgrade ATA211G for new firmware, refer
.
Q.14
Can I upgrade the ATA211G for new firmware remotely?
Ans.
Yes. If you know the public IP address of WAN port of ATA211G, you can use the FTP server of ATA211G
to upgrade the firmware. Refer “Software Upgradation”
.
Q.15
If I forgot the password, can I still use the Web Jeeves for configuration?
Ans.
Yes. But you need to set the password value to factory default.
154 Matrix SETU ATA211G System Manual
There are two important passwords for the configuration of ATA211G viz Admin Password and User
Password. Admin password protects the access to whole configuration while User password protects the access to only few configuration of ATA211G.
If you forgot the user password but you still have access to admin password, you can login to Web Jeeves and change the user password. But, if you forgot the admin password, you need to default the Password using access code '#***' from the Phone, connected to the ATA211G.
Refer “Reinstate Factory Defaults” and
for more details.
Q.16
I am not able to access the Web Jeeves since I forgot the IP address of LAN port of ATA211G. How can I know the IP address of LAN port?
Ans.
You can use the system commands to know the IP address of LAN/WAN port of ATA211G. Ensure that you have the SLT (compatible for CLI type) connected to the FXS port.
Q.17
Can I make call to PSTN, GSM number using the Mobile port of ATA211G?
Ans.
Yes. You can make call to any PSTN, GSM number using the Mobile port of ATA211G. You need to select the Mobile port by the command for 'Selective Trunk Access - Mobile', #83 followed by the number to be dialed. You can also do this by configuring the 'Outgoing Call Route' to 'Mobile' in the Web page 'FXS
Port', before dialing the desired number or by setting 'Dialed Number Based Routing'.
Q.18
Incoming calls on Mobile port of ATA211G does not place on FXS port. Why?
Ans.
Check the destination route configured in Webpage 'Mobile Port'.
Q.19
Can I change the configuration of ATA211G to factory default?
Ans.
Yes. You can change the configuration to factory default. Refer
“Reinstate Factory Defaults” for this
information.
Q.20
Can I select the SIP Trunk or Mobile port to make OG call?
Ans.
Yes. You can dial first the access code for the Mobile, SIP1, SIP2 or SIP3 and then dial the required number for OG call.
Q.21
Can I use the ATA211G for Least Cost Routing (LCR) application?
Ans.
Yes. You can do this by selecting 'Dialed Number based Routing' for parameter 'OG Call Route' in Web page for 'FXS Port'. After selecting option for routing, program in the Webpage 'Dialed Number Table', the numbers to be dialed and corresponding SIP Trunk or Mobile port as Destination Route which is cheaper for the call to be made.
Q.22
Can I route the Incoming calls on SIP to Mobile Port?
Ans.
Yes. You can configure suitable routing option for 'Route the Incoming Calls' in the Webpage 'SIP Trunk'.
.
Q.23 Though SIM card is inserted in the SIM card slot, LED labeled as 'L2' is blinking fast in Power On state?
Ans. Check whether the SIM card is inserted properly. If not, insert SIM card properly and restart the system.
Also check whether the SIM is activated. If deactivated, activate the SIM and check.
Q.24
LEDs are not glowing after power up?
Ans.
Check the power supply between mains and DC jack of ATA211G.
Q.25
Can I use the SIM PIN protection in ATA211G?
Ans. Yes, you can use the SIM PIN protection in ATA211G. (Refer SIM PIN feature in
topic)
Matrix SETU ATA211G System Manual 155
Q.27
ATA211G does not get registered to GSM network?
Ans. Check whether the SIM card is properly inserted and it is activated. Check SIM PIN. Check the availability of good GSM signal. Check the connectivity of antenna etc. (Refer SIM PIN feature in Mobile Port topic and 'Signal Strength' for more details)
Q.28 Incoming calls on Mobile port are not being placed on FXS Port however, caller still gets ring back tone.
Ans. Check the connectivity of analog phone to the FXS port of ATA211G.
Q.29
I am hearing garbled voice when call is made through Mobile port. What should I do?
Ans. If you are using antenna without wire, use wired antenna for better gain. If you are using wired antenna, change the antenna position.
Q.30 I have EPABX with FXS and FXO interface. Can ATA211G be integrated with existing EPABX and also reduces the call cost?
Ans. Yes. You can connect ATA211G with your existing EPABX. When connected with FXO port of EPABX, it enables you to make calls from the extensions of EPABX, directly to GSM network or VoIP which bypass the PSTN exchange and results in significant saving in call costs.
156 Matrix SETU ATA211G System Manual
Acronyms
MAC ms
MPLS
NAT
NTP
OG
PBX
PSTN
IC
IP
ISP
ITSP
ITU
LAN
L2 VLAN
LED
P2P
PPPoE
QoS
DNS
DST
DTMF
FEC
FTP
GMT
GSM
IANA
ASCII
CLI
CPT
CPTG
CWT
DHCP
DND
American Standard Code for Information Interchange
Caller Line Identification
Call Progress Tone
Call Progress Tone Generation
Call Waiting Tone
Dynamic Host Configuration Protocol
Do Not Disturb
Domain Name Service
Daylight Savings Time
Dual Tone Multi-Frequency
Forward Error Correction
File Transfer Protocol
Greenwich Mean Time
Global Systems for Mobile Communications
Internet Assigned Numbers Authority
Incoming call
Internet Protocol
Internet Service Provider
Internet Telephony Service Provider
International Telecommunication Union
Local Area Network
Layer2 Virtual Local Area Network
Light Emitting Diode
Media Access Control
Milliseconds
Multi Protocol Label Switching
Network Address Traversal
Network Time Protocol
Outgoing Call
Private Branch Exchange
Public Switched Telephone Network
Peer to Peer
Point to Point Protocol over Ethernet
Quality of Service
Matrix SETU ATA211G System Manual 157
STUN
TCP
TFTP
UDP
URI
URL
VAD
WAN
VoIP
RBT
RFC
RTP
SIP
SLT
SNTP
SOHO
Ring Back Tone
Request for Comments
Real Time Transport Protocol
Session Initiation Protocol
Single Line Telephone
Simple Network Time Protocol
Small Office Home Office
Simple Traversal of UDP over NAT
Transmission Control Protocol
Trivial File Transfer Protocol
User Datagram Protocol
Uniform Resource Identifier
Universal Reference/Resource Locator
Voice Activity Detection
Wide Area Network
Voice Over Internet Protocol
158 Matrix SETU ATA211G System Manual
Features at a Glance
Description
To enter programming code for Admin
To enter programming code for User
To exit programming mode
Speed Dialing
To default Login Password
Make a new call
Disconnect the call
Selective Trunk Access- Mobile
Selective Trunk Access-SIP1
Selective Trunk Access-SIP2
Selective Trunk Access-SIP3
#81
#82
#83
#84
#85
#86
Feature Code
#19-Admin Password
#18-User Password
0
#9-Index Number
#***
Matrix SETU ATA211G System Manual 159
System Commands
Command
11-WAN IP Address-#*
12-LAN IP Address-#*
13-Subnet Mask-#*
14-Subnet Mask-#*
15-Code-#*
16-Code-#*
Meaning
To program the WAN IP Address
To program the LAN IP Address
To program the Subnet Mask of WAN port
To program the Subnet Mask of LAN port
To program the connection type of WAN port; where, Code = 1 for DHCP, Code = 2 for PPPoE and Code=3 for Static
To enable/disable 'L2 VLAN/CoS' on WAN Port; where,
Code=0 for Disable and Code=1 for Enable
To default the ATA211G 21-Reverse Admin/User
Password-#*
31- #*
32-#*
33-#*
34-#*
35-#*
36-#*
37-#*
38 - SIP Trunk - #*
To display the WAN IP Address on SLT
To display the LAN IP address on SLT
To display the WAN Subnet Mask on SLT
To display the LAN Subnet Mask on SLT
To display the gateway address on SLT
To display the Primary DNS address on SLT
To display the connection type of WAN port on SLT
To display the registration status of SIP Trunk on SLT
39-#* To display the Secondary DNS address on SLT
51-Destination Number-#* To program Call Forward-Unconditional number
52-Code-#* Set/Cancel Call Forward-Unconditional; where, Code=1 to set and Code=0 to cancel the Call Forward-Unconditional
53-Destination Number-#* To program Call Forward-When Busy number
54-Code-#* Set/Cancel Call Forward-When Busy; where, Code=1 to set and Code=0 to cancel Call Forward-When Busy Number
55-Destination Number-#* To program Call Forward-When No Reply number
56-Code-#* Set/Cancel Call Forward-When No Reply; where, Code=1 to set and Code=0 to cancel Call Forward-When No Reply
57-XX-#* (XX is time in seconds)
Set Call Forward Timer
61-Code-#*
66-SIP Trunk-Code-#*
Set/Cancel DND; where, Code=1 to set and Code=0 to cancel
DND
Send/Block Caller ID for SIP1, SIP2, SIP3; where, SIP
Trunk=1 for SIP1, SIP Trunk=2 for SIP2, SIP Trunk=3 for SIP3 and Code=1 to block, Code=0 to send Caller ID
Allowed to?
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Admin and User
Only Admin
160 Matrix SETU ATA211G System Manual
Command
72-Code-#*
81-#*
82-Code-#*
99-#*
Meaning
Set/Cancel Call Waiting; where, Code=1 to set and Code=2 to cancel Call Waiting
To know the Signal Strength on phone LCD
To enable/disable CLIR on Mobile Port
Cancel all features
Allowed to?
Admin and User
Admin and User
Only Admin
Admin and User
Matrix SETU ATA211G System Manual 161
Product Specifications
PORT NAME APPLICATION
FXS Port For connecting Analog Phone or Fax Machine
LAN Port
WAN Port
To connect a Computer
To connect Ethernet cable router provided by service provider
Mobile Port
DC Jack
To connect to GSM Network
To connect the power adapter for DC supply voltage
NO. OF PORTS CONNECTOR TYPE
1 RJ 11
1
1
RJ 45, 10/100 Base T
RJ 45, 10/100 Base T
1
1
Antenna
DC Power Jack
VoIP and Networking Protocol
• SIP (RFC 3261)
• IPv4- Internet Protocol Version 4 (RFC 791)
• ARP- Address Resolution Protocol (RFC 0826)
• ICMP- Internet Control Message Protocol (RFC 0792)
• TCP- Transmission Control protocol (RFC 793)
• UDP- User Datagram Protocol (RFC 768)
• RTP- Real Time Protocol (RFC 1889)
• RTCP- Real Time Control Protocol (RFC 1889)
• SNTP- Simple Network Time Protocol
• PPP- Point-to-Point Protocol (RFC 1661)
• DNS- Protocol (RFC 2136)
• Outbound Proxy
• STUN
• NAT Keep Alive
• VLAN- Virtual LAN (Layer2)
GSM Parameters
• GSM Frequency Band: Quad-band: GSM 850, EGSM 900, DCS 1800, PCS 1900
• Compliant: ETSI GSM Phase 2/2+
• SIM Card: One SIM for GSM Port
• SIM Interface: 1.8V, 3V
• Transmission Power: Class 4 (2W) at EGSM900 and GSM850; Class 1 (1W) at DCS1800 and PCS 1900
• RF Sensitivity: Better than -106dBm
Antenna Parameters
• Type of Antenna: Fixed Omni Directional Swivel Antenna
• Antenna Gain: 2.5dBi
• Antenna Connector: SMA (Male), 50 Impedance
Voice Functionalities
• Three SIP Trunks
• DTMF: Inband, Outband (RFC 2833) and SIP INFO
• Call Progress Tone Generation: Select as per the country
• QoS (Layer3): RTP QoS and SIP QoS using DIffserv
162 Matrix SETU ATA211G System Manual
• Full Duplex Audio
• Echo Cancellation: G. 168, with programmable tail length of 8 - 32 msecs.
• Forward Error Correction (FEC)
• Voice Activity Detection (VAD)
• Fax using T.38 and Pass Through
• Flash Timer Programming
Voice Codec's
G.711 (a-Law and -Law), G.729, G.723
Telephony features
• Voice Calls using SIP proxy and Voice calls without using SIP proxy (Peer-to-Peer Calling)
• Call Waiting
• Caller ID Blocking
• Call Forwarding
• 3-Party conference
• Call Transfer
• Call Hold
• Caller ID: Generation and Display
• Answer supervision
• Disconnect supervision
• Speed Dialing
• Do-Not-Disturb (DND)
• Polarity Reversal
• Call Toggle
Time Settings
• Synchronizing with specific Time Server
Provisioning, Administration and Maintenance
• Auto Configuration
• Programming using Web Jeeves
• Software Upgrade (Using FTP Server)
• PCAP Trace
• Programming using Phone of parameters such as:
• LAN IP Address
• WAN IP Address, etc
LED Indication
LED for Power
LED for FXS
LED for Mobile
LED for SIP1
LED for SIP2
Security
Password Protected Administrator and User settings
Matrix SETU ATA211G System Manual 163
Dimension (W x H x D)
104mm x 27mm x 80mm (4.09" x 1.06" x 3.15")
Power Supply
External Adaptor: 12VDC@ 1.25Amp.
Power Consumption: 5W
Environmental
Operating Temperature: -10°C to 50°C (14°F to 122°F)
Operating Humidity: 5-95% RH, Non-Condensing
Storage Temperature: -40°C to 85°C (-40°F to 185°F)
Storage Humidity: 0-95% RH, Non-Condensing
164 Matrix SETU ATA211G System Manual
Warranty Statement
Matrix warrants to its consumer purchaser any of its products to be free of defects in material, workmanship and performance for a period of 15 months from date of manufacturing or 12 months from the date of installation which ever is earlier. During this warranty period, Matrix will at its option, repair or replace the product at no additional charge if the product is found to have manufacturing defect. Any replacement product or part/s may be furnished on an exchange basis, which shall be new or like-new, provided that it has functionality at least equal to that of the product, being replaced. All replacement parts and products will be the property of Matrix. Parts repaired or replaced will be under warranty throughout the remainder of the original warranty period only.
This limited warranty does not apply to:
1.
Products that have been subjected to abuse, accident, natural disaster, misuse, modification, tampering, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced
2.
or removed.
Products which have been damaged by lightning storms, water or power surges or which have been neglected, altered, used for a purpose other than the one for which they were manufactured, repaired by customer or any party without Matrix's written authorization or used in any manner inconsistent with
3.
4.
Matrix's instructions.
Products received improperly packed or physically damaged.
Products damaged due to operation of product outside the products' specifications or use without designated protections.
Warranty valid only if:
• Primary protection on all the ports provided.
• Mains supply is within limit and protected.
• Environment conditions are maintained as per the product specifications.
Warranty Card:
When the product is installed, please return the warranty card with:
• Date, signature and stamp of the customer.
• Date, signature and stamp of the channel partner.
Matrix assumes that the customer agrees with the warranty terms even when the warranty card is not signed and returned as suggested.
The Purchaser shall have to bear shipping charges for sending product to Matrix for testing/rectification. The product shall be shipped to the Purchaser at no-charge if the material is found to be under warranty. The Purchaser shall have to either insure the product or assume liability for loss or damage during transit. Matrix reserves the right to waive off or make any changes in its warranty policy without giving any notice.
If Matrix is unable to repair or replace, as applicable, a defective product which is covered by Matrix warranty,
Matrix shall, within a reasonable time after being notified of the defect, refund the purchase price of the product provided the consumer/purchaser returns the product to Matrix.
In no event will Matrix be liable for any damages including lost profits, lost business, lost savings, downtime or delay, labor, repair or material cost, injury to person, property or other incidental or consequential damages arising out of use of or inability to use such product, even if Matrix has been advised of the possibility of such damages or losses or for any claim by any other party.
Matrix SETU ATA211G System Manual 165
Except for the obligations specifically set forth in this Warranty Policy Statement, in no event shall Matrix be liable for any direct, indirect, special, incidental or consequential damages whether based on contract or any other legal theory and where advised of the possibility of such damages.
Neither Matrix nor any of its distributors, dealers or sub-dealers makes any other warranty of any kind, whether expressed or implied, with respect to Matrix products. Matrix and its distributors, dealers or sub-dealers specifically disclaim the implied warranties of merchantability and fitness for a particular purpose.
This warranty is not transferable and applies only to the original consumer purchaser of the Product. Warranty shall be void if the warranty card is not completed and registered with Matrix within 30 days of installation.
All legal course of action subjected to Vadodara (Gujarat, India) Jurisdiction only.
166 Matrix SETU ATA211G System Manual
Regulatory Information
Matrix SETU ATA211G System Manual 167
168 Matrix SETU ATA211G System Manual
Open Source Licensing Terms and Conditions
• The firmware of this product also includes some of the Open-Source software released under GNU General
Public License (GPL) Version 2. Terms of this license is printed in full below.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.,
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies
of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public
License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This
General Public License applies to most of the Free Software
Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights.
These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
Matrix SETU ATA211G System Manual 169
We protect your rights with two steps: (1) copyright the software, and
(2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you".
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the
Program (independent of having been made by running the Program).
Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion
170 Matrix SETU ATA211G System Manual
of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices
stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in
whole or in part contains or is derived from the Program or any
part thereof, to be licensed as a whole at no charge to all third
parties under the terms of this License.
c) If the modified program normally reads commands interactively
when run, you must cause it, when started running for such
interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a
notice that there is no warranty (or else, saying that you provide
a warranty) and that users may redistribute the program under
these conditions, and telling the user how to view a copy of this
License. (Exception: if the Program itself is interactive but
does not normally print such an announcement, your work based on
the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of
Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable
source code, which must be distributed under the terms of Sections
1 and 2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three
years, to give any third party, for a charge no more than your
Matrix SETU ATA211G System Manual 171
cost of physically performing source distribution, a complete
machine-readable copy of the corresponding source code, to be
distributed under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer
to distribute corresponding source code. (This alternative is
allowed only for noncommercial distribution and only if you
received the program in object code or executable form with such
an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License.
However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the
Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein.
You are not responsible for enforcing compliance by third parties to this License.
172 Matrix SETU ATA211G System Manual
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free
Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software
Foundation.
Matrix SETU ATA211G System Manual 173
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free
Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY
FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS
TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING
WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.
<one line to give the program's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
174 Matrix SETU ATA211G System Manual
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License along
with this program; if not, write to the Free Software Foundation, Inc.,
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
This is free software, and you are welcome to redistribute it
under certain conditions; type `show c' for details.
The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than `show w' and `show c'; they could even be mouse-clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program
`Gnomovision' (which makes passes at compilers) written by James Hacker.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General
Public License instead of this License.
Matrix SETU ATA211G System Manual 175
176 Matrix SETU ATA211G System Manual
Index
A
AC Impedance
Admin
Answer Signaling
Automatic Number Translation
C
Call Hold
Call Release Timer
Call Toggle
Call Transfer
Call Transfer - Attended
Call Transfer - Blind
Call Transfer-Attended
Call Transfer-Blind
Class of Service
Cloned
Connection Type
DHCP
PPPoE
Static
Current Date
Current Time
D
Daylight Saving Time
Debug configure system debug
debugs
Dialed Number Table
Destination Route
Maximum Digits
41, 50, 70, 73, 41, 50, 70, 73
Number
DiffServe
Digest Authentication
Disconnect Signaling
DNS Setting
DNS Address
Static DNS
E
Echo Cancellation
End of Dialing
G
General Request Timer
L
LEDs
M
Mobile Emergency Numbers
Mobile Network Selection
N
NAT Type
P
PCAP
prioritization of traffic
R
Receive Gain
Registration Retry Timer
Reinstate Factory Defaults
Re-registration Timer
Return Call to Original Caller
Ring
rinstance
Routing Mode
Routing Tone
RTP QoS
S
SIM PIN
SIP ID
SIP INVITE Timer
SIP Over TCP
SIP Provisional Timer
SIP Trunk Mode
Speed Dialing
Static Routing
Syslogs
T
TCP NAT Keep Alive
Interval
Three-party Conference
Time Offset
Transmit Gain
U
UDP NAT Keep Alive
Interval
Unique
User
V
VLAN header
VLAN ID
VLAN/CoS Layer
RTP CoS
SIP CoS
Vocoders
Voice Activity Detection (VAD)
Volume
www.matrixtelecom.hu
Magyarországon a Matrix Telecom Ltd. képviselete,
Matrix termékek importőre, kizárólagos forgalmazója:
1095 Budapest, Mester u. 34
.
Telefon: *218-5542, 215-9771, 215-7550, 216-7017, 216-7018
Fax: 218-5542 Mobil: 30 940-1970, 20 949-2688
E-mail: [email protected] Web: www.delton.hu
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement