Dell 7609WU - WUXGA DLP Projector User`s guide

Dell™ 7609WU Projector
User’s Guide
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you
make better use of your projector.
NOTICE: A NOTICE indicates either potential damage to
hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property
damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2008 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written
permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell
Inc.; DLP, DLP® logo and DarkChip™3 are either trademarks for Texas
Instruments; Microsoft and Windows are registered trademarks or trademarks
of Microsoft Corporation in the United States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either
the entities claiming the marks and names or their products. Dell Inc. disclaims
any proprietary interest in trademarks and trade names other than its own.
Model 7609WU
April 2008 Rev. A00
Contents
1
Your Dell Projector .
. . . . . . . . . . . . . . . . .
About Your Projector
2
. . . . . . . . . . . . . . . . .
Connecting Your Projector .
Connecting a Computer
. . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
Connecting a Computer Using a VGA Cable
. . . . .
Connecting a Computer Using a RS232 Cable
. . .
Connecting a Computer Using an Ethernet Cable
.
6
7
8
9
9
10
11
Connecting a Computer Using a DisplayPort Cable
12
Monitor Loop-Through Connection Using VGA
Cables . . . . . . . . . . . . . . . . . . . . . .
. .
13
. . . . . . . . . . . . . . . .
14
Connecting a DVD Player
Connecting a DVD Player Using an S-video Cable
.
14
Connecting a DVD Player Using a Composite Cable 15
Connecting a DVD Player Using a Component
(VGA to YPbPr) Cable . . . . . . . . . . . . .
. . .
16
Connecting a DVD Player Using a Component
(YPbPr to YPbPr) Cable . . . . . . . . . . . .
. . .
17
Connecting a DVD Player Using an HDMI Cable
Professional Installation Options
. .
18
. . . . . . . . . . . .
19
Installation for Driving Automatic Screen
. . . . .
Connecting a Commercial RS232 Control Box
. . .
Contents
19
20
3
3
Using Your Projector
. . . . . . . . . . . . . . . .
21
Turning Your Projector On
. . . . . . . . . . . . . . . .
21
Turning Your Projector Off
. . . . . . . . . . . . . . . .
21
Adjusting the Projected Image
. . . . . . . . . . . . .
Raising the Projector Height
. . . . . . . . . . . .
Lowering the Projector Height
. . . . . . . . . . .
. . . . . . . . . . . .
24
. . . . . . . . . . . . . . . . .
25
Using the Remote Control
. . . . . . . . . . . . . . . .
27
. . . . . . . . . . . . . .
29
. . . . . . . . . . . . . . . . . . . . .
29
Using the On-Screen Display
INPUT SELECT
. . . . . . . . . . . . . . . . . . .
29
AUTO-ADJUST
. . . . . . . . . . . . . . . . . . .
30
. . . . . . . . . . . . . . . . . . . . . . .
31
SET UP
PICTURE (in PC Mode)
. . . . . . . . . . . . . . .
PICTURE (in Video Mode)
DISPLAY (in PC Mode)
34
. . . . . . . . . . . . . . .
35
. . . . . . . . . . . . . .
36
. . . . . . . . . . . . . . . . . . .
37
. . . . . . . . . . . . . . . . . . . . . . . .
38
PIP SETTINGS .
LAMP
33
. . . . . . . . . . . . . .
DISPLAY (in Video Mode)
LANGUAGE
OTHERS
4
22
23
Adjusting Projection Image Size
Main Menu
22
. . . . . . . .
Adjusting the Projector Zoom and Focus
Using the Control Panel
22
. . . . . . . . . . . . . . . . . . . . .
39
. . . . . . . . . . . . . . . . . . . . . . .
40
Troubleshooting Your Projector
Changing the Lamp .
. . . . . . . .
44
. . . . . . . . . . . . . . . . . . .
48
Contents
4
5
Specifications
6
Contacting Dell™
7
Appendix: Glossary
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
Contents
50
56
57
5
1
Your Dell Projector
Before connecting your projector ensure that all the necessary components are
available. Your projector ships with the components shown below. Contact Dell
(See "Contacting Dell™" on page 56) if any of the components are missing.
Package Contents
Power cable
1.8m VGA cable (VGA to VGA)
2.0m DisplayPort cable
Remote control
AAA Batteries (2)
CD User’s Guide & Documentation
Your Dell Projector
6
About Your Projector
1
Control panel
2
IR receivers
3
Focus ring
4
Lens
5
Elevator button
6
Lens cap
CAUTION: Safety Instructions
1 Do not use the projector near appliances that generate a lot of heat.
2 Do not use the projector in areas where there is an excessive amount of dust. The
dust may cause the system to fail and the projector will automatically shut down.
3 Ensure that the projector is mounted in a well-ventilated area.
4 Do not block the ventilation slots and openings on the projector.
5 Ensure that the projector operates between ambient temperatures (5ºC to 35ºC).
NOTE: For more information, see the safety information that shipped with your
projector.
Your Dell Projector
7
Connecting Your Projector
1
RJ45 network connector
2
S-video input connector
3
Composite video input connector
4
RS232 connector
5
USB remote connector
6
Audio output connector
7
Audio input connector
8
12 Volt DC relay output
9
5 Volt DC relay output
10
DisplayPort connector
11
HDMI input connectors
12
VGA-A input (D-sub) connector
13
VGA-B input (D-sub) connector
14
VGA-B output (monitor loop-through) connector
15
Component video input connectors
16
Power cable connector
17
Security cable slot
2
CAUTION: Before you begin any of the procedures in this section, follow the
"Safety Instructions" on page 7.
Connecting Your Projector
8
Connecting a Computer
Connecting a Computer Using a VGA Cable
1
Power cable
2
VGA to VGA cable
3
USB to USB cable
NOTE: The USB cable is not provided by Dell. You can buy the USB cable from
the Dell website
NOTE: The USB cable must be connected if you want to use the Next Page and
Previous Page features on the remote control.
Connecting Your Projector
9
Connecting a Computer Using a RS232 Cable
1
Power cable
2
RS232 cable
NOTE: The RS232 cable is not provided by Dell.Consult a professional installer
for the cable and RS232 remote control software.
Connecting Your Projector
10
Connecting a Computer Using an Ethernet Cable
1
Power cable
2
Ethernet (RJ45) cable
NOTE: The Ethernet (RJ45) cable is not provided by Dell.
Connecting Your Projector
11
Connecting a Computer Using a DisplayPort Cable
1
Power cable
2
DisplayPort cable
Connecting Your Projector
12
Monitor Loop-Through Connection Using VGA Cables
1
Power cable
2
VGA to VGA cable
Connecting Your Projector
13
Connecting a DVD Player
Connecting a DVD Player Using an S-video Cable
1
Power cable
2
S-video cable
NOTE: The S-video cable is not provided by Dell. You can buy the S-Video
Extension (50ft/100ft) cable from the Dell website.
Connecting Your Projector
14
Connecting a DVD Player Using a Composite Cable
1
Power cable
2
Composite video cable
NOTE: The Composite cable is not provided by Dell. You can buy the Composite
Video Extension (50ft/100ft) cable from the Dell website.
Connecting Your Projector
15
Connecting a DVD Player Using a Component (VGA to YPbPr) Cable
1
Power cable
2
VGA to YPbPr cable
NOTE: The VGA to YPbPr cable is not provided by Dell. You can buy the VGA to
YPbPr Extension (50ft/100ft) cable from the Dell website.
Input.
NOTE: You can connect the component cable to either VGA-A Input or VGA-B
Connecting Your Projector
16
Connecting a DVD Player Using a Component (YPbPr to YPbPr) Cable
1
Power cable
2
YPbPr to YPbPr cable
NOTE: The YPbPr to YPbPr cable is not provided by Dell.
Connecting Your Projector
17
Connecting a DVD Player Using an HDMI Cable
1
Power cable
2
HDMI cable
NOTE: The HDMI cable is not provided by Dell.
Connecting Your Projector
18
Professional Installation Options
Installation for Driving Automatic Screen
1
Power cable
2
12V DC power cable
3
Automatic screen
NOTE: The 12V DC power cable is not provided by Dell.
The 12V DC power cable has to be connected to the DC 12V jack.
NOTE: Use a 12V DC plug
with a dimension 1.7mm (ID) x 4.00mm (DD) x
9.5 mm (shaft) to connect the automatic screen with the projector.
Connecting Your Projector
19
Connecting a Commercial RS232 Control Box
1
Power cable
2
RS232 cable
3
Commercial RS232 control box
NOTE: The RS232 cable is not provided by Dell. Consult a professional installer
for the cable and RS232 remote control software.
Connecting Your Projector
20
3
Using Your Projector
Turning Your Projector On
NOTE: Turn on the projector before you turn on the source. The Power button
light blinks blue until it is pressed.
1 Remove the lens cap.
CAUTION: The lens cap must be removed before turning on the projector.
Otherwise, the metal plate inside the lens cap will become very hot and may
cause injury if touched.
2 Connect the power cable and the appropriate signal cables. For information about
connecting the projector, see "Connecting Your Projector" on page 8.
3 Press the Power button (see "Using the Control Panel" on page 25 to locate the
Power button).
4 Turn on your source (computer, DVD player, etc.). The projector automatically
detects your source.
NOTE: If you have multiple sources connected to the projector, press the
Source button on the remote control or control panel to select the desired source.
5 The Dell Logo will continue for 30 seconds while powered on.
If the "Searching for signal..." message appears on the screen, ensure that the
appropriate cables are securely connected.
Turning Your Projector Off
NOTICE: Unplug the cables from the projector after properly shutting down as
explained in the following procedure.
1 Press the Power button.
2 Press the Power button again. The cooling fans will continue to operate for 120
seconds.
3 To quickly turn off the projector, press the Power button while the projector’s
cooling fans are still running.
NOTE: Before you turn on the projector again, wait for 60 seconds to allow the
internal temperature to stabilize.
4 Disconnect the power cable from the electrical outlet and the projector.
Using Your Projector
21
NOTE: If you press the Power button while the projector is running, the "Press
Power Button to Turn off Projector" message appears on the screen. To clear the
message, press the Menu button on the control panel or ignore the message; the
message disappears after 10 seconds.
Adjusting the Projected Image
Raising the Projector Height
1 Press the Elevator button.
2 Raise the projector to the desired display angle, and then release the button to
lock the elevator foot into position.
3 Use the tilt adjustment wheel to fine-tune the display angle.
Lowering the Projector Height
CAUTION: Support the projector properly and do not place you hand near the
elevator foot when pressing the elevator button.
1 Press the Elevator button.
2 Lower the projector, and then release the button to lock the elevator foot into
position.
1
Elevator button
2
Elevator foot
3
Tilt adjustment wheel
Using Your Projector
22
Adjusting the Projector Zoom and Focus
1 Open the side door of the projector.
CAUTION: To avoid damaging the projector, ensure that the side door is fully
closed and the elevator foot is fully retracted before moving the projector.
2 Unlock the lens shift lock, before you adjust the lens shift.
3 Turn the vertical/horizontal lens shift knob to shift the lens.
4 After adjusting the lens shift, lock the lens shift lock.
5 Pull the zoom ring adjustment up and down to zoom in and out.
6 Rotate the focus ring adjustment until the image is clear. The projector focuses at
distances ranging between 3.28 ft to 39.37 ft (1.0m to 12.0m).
7 Close the side door of the projector.
1 2 34 5
1
Side door
2
Vertical lens shift knob
3
Lens shift lock
4
Horizontal lens shift knob
5
Zoom ring
6
Focus ring
6
Using Your Projector
23
Adjusting Projection Image Size
Using Your Projector
24
Screen
(Diagonal)
Screen
Size
Distance
Max.
25.1"
(63.7cm)
85.3"
(216.6cm)
138.0"
(350.5cm)
193.2"
(490.6cm)
245.8"
(624.5cm)
301.0"
(764.6cm)
Min.
20.91"
(53.1cm)
71.08"
(180.5cm)
114.98"
(292.0cm)
160.97"
(408.9cm)
204.87"
(520.4cm)
250.87"
(637.2cm)
Max.
(WxH)
21.3"X 13.3"
72.4" X 45.2"
117.0" X 73.1"
(54.1cm X
33.7cm)
(183.8cm X
114.7cm)
(297.3cm X
185.6cm)
(416.2cm X
259.8cm)
Min.
(WxH)
17.7" X 11.1"
60.3" X 37.7"
97.5" X 60.9"
136.5" X 85.3"
(45.0cm X
28.12cm)
(153.1cm X
95.7cm)
(247.7cm X
154.8cm)
(346.7cm X
216.7cm)
(441.3cm X
275.8cm)
(540.3cm X
337.7cm)
3.28' (1.0m)
11.15' (3.4m)
18.04' (5.5m)
25.26' (7.7m)
32.15' (9.8m)
39.37' (12.0m)
163.9" X 102.3" 208.6" X 130.2" 255.4" X 159.4"
(529.7cm X
330.7cm)
(648.6cmX
404.9cm)
173.7" X 108.6" 212.7" X 133.0"
* This graph is for user reference only.
Using the Control Panel
1
3
2
4
5
12
11
10
6
7
9
1
LAMP warning light
8
•If the LAMP light is solid amber, replace the
lamp (See "LAMP" on page 38).
•If the LAMP light is blinking amber, the
projector automatically shuts down indicating a
system failure. If this problem persists, contact
Dell™ (See "Contacting Dell™" on page 56).
Using Your Projector
25
2
TEMP warning light
• A solid amber TEMP light indicates that the
projector, lamp, or lamp driver are overheated.
The display automatically shuts down. Turn the
display on again after the projector cools down.
If the problem persists, contact Dell™ (See
"Contacting Dell™" on page 56).
• A blinking amber TEMP light indicates that a
projector fan or color wheel have failed and the
projector automatically shuts down. If the
problem persists, contact Dell™ (See
"Contacting Dell™" on page 56).
3
Power
Allows you to turn the projector on and off. For
more information, see "Turning Your Projector
On" on page 21 and "Turning Your Projector Off"
on page 21.
4
Volume Control
Allows you to increase or decrease the volume.
5
Up
/ Keystone
adjustment
Allows you to select options from the On Screen
Display (OSD) menu. You can also use this
button to adjust the image distortion caused by
tilting the projector.
6
Right
Adjust
Allows you to adjust the OSD setting. You can
also synchronize the projector to the input
source. Auto Adjust does not operate if the onscreen display (OSD) is displayed.
7
IR Receiver
Point the remote control towards the IR receiver
and press a button.
8
Down
/ Keystone
adjustment
Allows you to select options from the On Screen
Display (OSD) menu. You can also use this
button to adjust the image distortion caused by
tilting the projector.
9
Menu
Allows you to activate the OSD. Use
and the Menu button to navigate through the
OSD.
10
Left
/ Auto
/ Source
Allows you to adjust the OSD setting. You can
also use the
button to toggle through Digital
RGB, Analog RGB, Composite, Component, and
S-video sources when multiple sources are
connected to the projector.
Using Your Projector
26
11
Enter
Allows you to confirm a selected OSD option.
12
Brightness and
Contrast Control
Allows you to adjust the brightness and contrast
values.
Using the Remote Control
11
1
2
12
3
4
13
5
14
15
6
7
16
17
8
18
9
19
10
20
Using Your Projector
27
1
Power
Turns the projector on and off. For more
information, see "Turning Your Projector On" on
page 21 and "Turning Your Projector Off" on
page 21.
Press and hold for 10 seconds to exit the lockup
state and go back to standby mode when
projector is in lockup state. (eg. Lamp error, over
heat etc.)
2
Enter
Press to confirm the selection.
3
Right
Press to adjust the OSD setting.
4
Down
Press to select OSD items.
5
Aspect Ratio
Press to change the aspect ratio of a displayed
image.
6
Page up
Press to move to the previous page.
7
Mute
Press to mute or un-mute the projector speaker.
8
Page down
Press to move to the next page.
9
Video mode
The Dell 7609WU projector has preset
configurations that are optimized for displaying
data (PC Graphics) or videos (movies, games,
etc.). Press the Video Mode button to toggle
between Presentation mode, Bright mode,
Movie mode, sRGB, or CUSTOM mode (for the
user to set up and save preferred settings).
Pressing the Video Mode button once will show
the current display mode. Pressing the Video
Mode button again will allow the projector to
switch between display modes.
10 Blank screen
Press to hide / un-hide the image.
11 Up
Press to select OSD items.
12 Left
Press to adjust the OSD setting.
13 Menu
Press to activate the OSD.
14 Volume up
Press to increase the volume.
15 Laser
Aim the remote control at the screen, press and
hold the laser button to activate the laser light.
16 Volume down
Press to decrease the volume.
Using Your Projector
28
17 Keystone
adjustment
Press to adjust image distortion caused by tilting
the projector. (±30 degrees)
18 Source
Press to switch between Digital RGB, Analog
RGB, Composite, S-video and Component
sources.
19 Auto adjust
Press to synchronize the projector to the input
source. Auto adjust does not operate if the OSD
(On-Screen Display) is displayed.
20 Keystone
adjustment
Press to adjust image distortion caused by tilting
the projector. (±30 degrees)
Using the On-Screen Display
The projector has a multi-language On-Screen Display (OSD) that can be
displayed with or without an input source present.
To navigate through the tabs in the Main menu, press the
or
buttons on
your projector’s control panel or remote control. To select a submenu, press the
Enter button on your projector’s control panel or remote control.
To select an option, press the
or
on your projector’s control panel or
remote control. When an item is selected, the color changes to dark blue. Use
or
on the control panel or remote control to adjust the settings.
To go back to the Main menu, go to the Back tab and press the Enter button on
the control panel or the remote control.
To exit the OSD, go to the EXIT tab and press the Enter button or press the
Menu button directly on the control panel or the remote control.
Main Menu
INPUT SELECT
The Input Select menu allows you to select your projector’s input source.
Using Your Projector
29
AUTO SOURCE—Select On (the
default option) to autodetect the
available input signals. If you press
the Source button when the
projector is on, it automatically
finds the next available input signal.
Select Off to lock the current input
signal. If you press the Source
button when the Auto Source mode
is set to Off, you can manually select
the input signal.
VGA-A—Press Enter to detect the
VGA-A signal.
VGA-B—Press Enter to detect the
VGA-B signal.
S-VIDEO—Press Enter to detect the
S-Video signal.
COMPOSITE VIDEO—Press Enter to detect the Composite Video signal.
COMPONENT—Press Enter to detect the Component Video signal.
DISPLAYPORT—Press Enter to detect the DisplayPort signal.
HDMI-A—Press Enter to detect the HDMI-A signal.
HDMI-B—Press Enter to detect the HDMI-B signal.
AUTO-ADJUST
Auto Adjust automatically adjusts the
projector's FREQUENCY and
TRACKING in PC mode. While
Auto Adjustment is in progress, the following message appears on the screen,
"Auto Adjustment in Progress...".
Using Your Projector
30
SET UP
It includes H. Keystone, V. Keystone, Auto Keystone, Projector Mode, Aspect
Ratio, Network Settings, and Projector Info.
H. KEYSTONE—Adjusts the image distortion caused by horizontal shifting of the
projector orientation.
V. KEYSTONE—Adjusts the image distortion caused by tilting the projector.
AUTO KEYSTONE—Select On to enable the auto correction for vertical image
distortion caused by tilting the projector. Select Off to disable the auto correction.
PROJECTOR MODE—Allows you to select the projector mode, depending upon how
the projector is mounted.
•
Front Projection-Desktop — This is the default option.
•
Front Projection-Ceiling Mount — The projector turns the image upside
down for ceiling-mounted projection.
•
Rear Projection-Desktop — The projector reverses the image so that you can
project the image from behind a translucent screen.
•
Rear Projection-Ceiling Mount — The projector reverses and turns the
image upside down. You can project the image from behind a translucent screen
with a ceiling-mounted projection.
ASPECT RATIO—Allows you to set the aspect ratio.
•
Original — The input source scales to fit the screen while keeping the aspect
ratio of the input source.
Using Your Projector
31
•
4:3 — The input source scales to fit the height of the screen and projects a
4:3 image.
•
Wide — The input source scales to fit the width of the screen to project a
wide screen image.
NETWORK SETTINGS—Allows you to manage the network configuration. Press Enter
to open the Network Settings menu.
• DHCP—Select On to assign an IP address to the projector from a DHCP server
automatically. Select Off to assign an IP address manually.
or
to select the
• IP Address—Press Enter to set up an IP address. Press
number position,
or
to change the number.
or
to
• Subnet Mask—Press Enter to set up a subnet mask number. Press
select the number position,
or
to change the number.
• Gateway—Press Enter to set the default gateway of the network connected to the
or
to select the number position,
or
to change the
projector. Press
number.
• DNS—Type in the IP address of the DNS server on the network connected to the
projector. 12 numeric characters are used.
• Apply Change—Press Enter to confirm the settings.
• Reset Network—Press Enter to reset to the default settings.
• Network—Select On to activate and Off to deactivate network connections.
DC 5V POWER—Select this option to turn the DC 5V power On or Off.
VGA LOOP THROUGH—Select this option to turn the VGA Loop through On or Off.
Using Your Projector
32
PROJECTOR INFO—Displays the projector model name, the present input source and
the projector serial number (PPID#).
PICTURE (in PC Mode)
Using the Picture menu, you can adjust the display settings of your projector. The
Picture menu provides the following options:
BRIGHTNESS—Use
CONTRAST—Use
or
or
to adjust the brightness of the image.
to adjust the display contrast.
COLOR TEMP—Allows you to adjust the color temperature. The screen appears
cooler at higher color temperatures and warmer at lower color temperatures.
COLOR ADJUST—Allows you to manually adjust the colours red, green, and blue.
When you adjust the values in the Color Adjust menu, the Custom mode is
activated. The values are saved in the Custom mode.
Using Your Projector
33
PICTURE (in Video Mode)
Using the Picture menu, you can adjust the display settings of your projector. The
Picture menu provides the following options:
BRIGHTNESS—Use
CONTRAST—Use
or
or
to adjust the brightness of the image.
to adjust the display contrast.
COLOR TEMP—Allows you to adjust the color temperature. The screen appears
cooler at higher color temperatures and warmer at lower color temperatures.
COLOR ADJUST—Allows you to manually adjust the colours red, green, and blue.
When you adjust the values in the Color Adjust menu, the Custom mode is
activated. The values are saved in the Custom mode.
SATURATION—Allows you to adjust the video source from black and white to fully
saturated color. Press
to decrease the amount of color in the image and
to
increase the amount of color in the image (Selectable for S-Video and Composite
video signals only).
SHARPNESS—Allows you to adjust the image sharpness. Press
sharpness and
to increase the sharpness.
to decrease the
TINT—Press
to increase the amount of green in the image and
to increase
the amount of red in the image (Selectable for S-Video and Composite video
signals only).
Using Your Projector
34
DISPLAY (in PC Mode)
Using the Display menu, you can adjust the display settings of your projector. The
Display menu provides the following options:
VIDEO MODE—Allows you to optimize the projector’s display mode:
Presentation, Bright, Movie, sRGB (provides a more accurate color
representation), and Custom (set your preferred settings for these two options). If
you adjust the settings for White Intensity or Degamma, the projector
automatically switches to Custom.
SIGNAL TYPE—Allows you to manually select the signal type: RGB, YCbCr, or YPbPr.
to digitally magnify an image up to 8 times on the projection
ZOOM—Press
screen and press
to reduce the zoomed image (for single display).
ZOOM NAVIGATION—Press
to navigate the projection screen.
WHITE INTENSITY—Set 0 to maximize the color reproduction and 10 to maximize
the brightness.
DEGAMMA—Allows you to adjust among the 4 preset values (1, 2, 3, 4) to change
the color performance of the display.
HORIZONTAL POSITION—Press
image to the right.
to move the image to the left and
to move the
Using Your Projector
35
VERTICAL POSITION—Press
up.
to move the image down and
to move the image
FREQUENCY—Allows you to change the display data clock frequency to match the
frequency of your computer graphics card. If you see a vertical flickering wave, use
Frequency control to minimize the bars. This is a coarse adjustment.
TRACKING—Allows you to synchronize the phase of the display signal with the
graphic card. If you experience an unstable or flickering image, use Tracking to
correct it. This is a fine adjustment.
DISPLAY (in Video Mode)
Using the Display menu, you can adjust the display settings of your projector. The
Display menu provides the following options:
VIDEO MODE—Allows you to optimize the projector’s display mode:
Presentation, Bright, Movie, sRGB (provides a more accurate color
representation), and Custom (set your preferred settings for these two options). If
you adjust the settings for White Intensity or Degamma, the projector
automatically switches to Custom.
SIGNAL TYPE—Manually select the signal type: RGB, YCbCr, or YPbPr.
to digitally magnify an image up to 8 times on the projection
ZOOM—Press
screen and press
to reduce the zoomed image (for single display).
ZOOM NAVIGATION—Press
to navigate the projection screen.
WHITE INTENSITY—Set 0 to maximize the color reproduction and 10 to maximize
the brightness.
DEGAMMA—Adjust among the 4 preset values (1, 2, 3, 4) to change the color
performance of the display.
Using Your Projector
36
PIP SETTINGS
NOTE: When swapping the foreground and background displays, the smallest
screen size of foreground display will vary depending on the different
combinations of signal sources for PIP.
On to enable the picture-in-picture display; select
PIP/PBP IMAGE—Select
On to enable the picture-by-picture display. Select Off to disable the
function.
PIP/PBP SOURCE—The possible PIP/PBP source is available in the OSD selection
depending on the current primary input source. To see the possible combination
of the sources, refer to page 54.
PIP SIZE—Adjusts the image size of the PIP display.
PIP POSITION—Changes the PIP position to the four different corners of the display.
Using Your Projector
37
LAMP
Using the Lamp menu, you can adjust the display settings of your projector. The
Lamp menu provides the following options:
LAMP HOUR—Displays the operating hours since the last lamp timer reset.
POWER SAVING—Select Yes to set the Power Saving delay period. The delay period is
the time that you want the projector to wait without an input signal. By default,
the delay period is set to 120 minutes. However, you can set this to 5, 15, 30, 45,
60, or 120 minutes.
If an input signal is not detected during the delay period, the projector turns off
the lamp and goes into power saving mode. If an input signal is detected when the
projector is in power saving mode, the projector automatically turns on. If an input
signal is not detected within two hours, the projector switches from Power Saving
mode to Power Off mode. To turn on the projector press the Power button.
ECO MODE—Select On to use the lamp at a lower power level (264 Watts), which
may provide longer lamp life, quieter operation, and dimmer luminance output on
the screen. Select Off to operate at normal power level (300 Watts).
LAMP RESET—After you install a new lamp, select Yes to reset the lamp timer.
QUICK SHUTDOWN—Select Yes to turn off the projector with a single press of the
Power button. This function allows the projector to quick power off with an
accelerated fan speed.
NOTE: Slightly higher acoustic noise is expected during quick power off.
Using Your Projector
38
LANGUAGE
The Language menu allows you to set the language for the OSD.
Using Your Projector
39
OTHERS
AUDIO SETTINGS—Press Enter to open the Audio Settings menu.
Using Your Projector
40
• Audio Source—Select either HDMI, Audio (Audio In), or DisplayPort as the
audio source for use.
to decrease the volume and
to increase the volume.
• Volume—Press
• Mute—Allows you to mute the sound.
• Balance—Use
or
to adjust the left and right speaker balance.
or
to adjust the bass tones.
• Bass—Use
or
to adjust the treble tones.
• Treble—Use
CLOSED CAPTION—Select On to deliver closed caption content to accommodate the
hearing-impaired. Select Off to disable closed caption.Select a suitable caption
channel from CC1 ~ CC4 and Text1 ~ Text4.
NOTE: Closed caption is only supported for input signals of S-Video and
Composite Video.
CUSTOMIZED SCREEN —Press Enter to pop up a Customized Screen menu. Input in a
source then press Enter and select Yes. The projector will capture the screen image
as a My Customized logo. This screen replaces all the original screens with the
Dell logo. You can recover the default screen by selecting Dell Logo on the pop-up
screen.
MENU LOCK—Select On to enable the Menu Lock and hide the OSD menu. Select
OFF to disable the Menu Lock and display the OSD menu.
NOTE: If the OSD disappears while you disable Menu Lock, press the Menu
button on the projector’s control panel or the remote control for 15 seconds, and
then disable the function.
MENU TIMEOUT—Allows you to adjust the time for an OSD Timeout. By default,
the OSD disappears after 30 seconds of non-activity.
MENU POSITION—Allows you to select the position of the OSD menu on the screen.
Using Your Projector
41
MENU TRANSPARENCY—Select to change the transparency level of the OSD
background.
PASSWORD—When Password Protect is enabled, a Password Protect screen
requesting you to enter a password will be displayed when the power for the
projector is first turned on. By default, this function is disabled. You can enable
this feature by using the Password menu. This password security feature will be
activated the next time you turn on the projector and you will be asked to enter
the projector's password:
You can use the following steps to enable the Password Protect feature and set a
password. The last step (step 3) describes how you can disable the password.
1
First time password input request:
a
Go to Others menu, press Enter and then select Password Enable
to enable the password setting.
b
Enabling the Password function will pop up a character screen. Key
in a 4-digit character code (letters and/or numbers) on the screen
and press the Enter button.
c
To confirm, enter the password again.
Using Your Projector
42
d
2
If the password verification is successful, you can resume accessing
the projector's functions and its utilities.
If you have entered an incorrect password, you will be given another
two chances to enter the correct password. After three invalid attempts,
the projector will automatically turn off.
NOTE: If you forget your password, contact Dell™ (see "Contacting Dell™" on
page 56) or contact qualified service personnel.
3
To cancel the password function, select Off and enter the password to
disable the function.
CHANGE PASSWORD—Key in the original password, then enter the new password and
confirm the new password again.
TEST PATTERN—Select On to activate the built-in Test Pattern for self-testing on
focus and resolution. Select Off to disable the function.
FACTORY RESET —Select On to reset the projector to its factory default settings.
Reset items include both computer sources and video source settings.
Using Your Projector
43
Troubleshooting Your Projector
4
If you experience problems with your projector, see the following troubleshooting
tips. If the problem persists, contact Dell™. See "Contacting Dell™" on page 56.
Problem
Possible Solution
No image appears on the
screen
• Ensure that the lens cap is removed and the
projector is turned on.
• Ensure the external graphics port is enabled.
If you are using a Dell™ portable computer,
press
(Fn+F8). For other
computers, see your respective
documentation.
• Ensure that all the cables are securely
connected. See "Connecting Your Projector"
on page 8.
• Ensure that the pins of the connectors are
not bent or broken.
• Ensure that the lamp is securely installed
(see "Changing the Lamp" on page 48).
• Use Test Pattern in the Others menu.
Ensure that the colors of the test pattern are
correct.
Troubleshooting Your Projector
44
Problem (continued)
Partial, scrolling, or
incorrectly displayed image
Possible Solution (continued)
1 Press the Auto Adjust button on the remote
control or the control panel.
2 If you are using a Dell™ portable computer,
set the resolution of the computer to WXGA
(1280 x 800) or XGA (1024 x 768):
a Right-click the unused portion of your
Windows desktop, click Properties and
then select Settings tab.
b Verify that the setting is 1280 x 800 or
1024 x 768 pixels for the external monitor
port.
c Press
(Fn+F8).
If you experience difficulty in changing
resolutions or your monitor freezes, restart all
the equipment and the projector.
If you are not using a Dell™ portable
computer, see your documentation.
If problem persists, upgrade your computer
graphic card driver (video driver) to its latest
version and test again with projector.
The screen does not display
your presentation
If you are using a Dell™ portable computer,
(Fn+F8).
press
Image is unstable or flickering Adjust the tracking in the OSD Display submenu (in PC Mode only).
Image has vertical flickering
bar
Adjust the frequency in the OSD Display submenu (in PC Mode only).
Image color is incorrect
• If the display receives the wrong signal
output from the graphics card, please set the
signal type to RGB in the OSD Display tab.
• Use Test Pattern in the Others menu.
Ensure that the colors of the test pattern are
correct.
Image is out of focus
1 Adjust the focus ring on the projector lens.
2 Ensure that the projection screen is within
the required distance from the projector
(3.28 ft [1 m] to 39.37 ft [12 m]).
Troubleshooting Your Projector
45
Problem (continued)
Possible Solution (continued)
The image is stretched when
displaying a 16:9 DVD
The projector automatically detects the input
signal format. It will maintain the aspect ratio
of the projected image according to the input
signal format with an Original setting.
If the image is still stretched, adjust the aspect
ratio in the Set Up menu in the OSD.
Image is reversed
Select Set Up from the OSD and adjust the
projector mode.
Lamp is burned out or makes
a popping sound
When the lamp reaches its end of life, it may
burn out and may make a loud popping sound.
If this occurs, the projector does not turn back
on. To replace the lamp, see "Changing the
Lamp" on page 48.
LAMP light is solid amber
If the LAMP light is solid amber, replace the
lamp.
LAMP light is blinking amber
If the LAMP light and the Power light are
blinking amber, this means that the lamp
driver has failed and the projector will
automatically shut down.
If the LAMP light is blinking amber and the
Power light is solid blue, this means that the
color wheel has failed and the projector will
automatically shut down.
Unplug the power cable after 3minutes and
then turn the display on again. If this problem
persists, contact Dell™. (See "Contacting
Dell™" on page 56)
TEMP light is solid amber
The projector is overheated and the display
automatically shuts down. Turn the display on
again after the projector cools down. If the
problem persists, contact Dell™. (See
"Contacting Dell™" on page 56)
TEMP light is blinking amber A projector fan has failed and the projector
will automatically shut down. If the problem
persists, contact Dell™. (See "Contacting
Dell™" on page 56)
Troubleshooting Your Projector
46
Problem (continued)
Possible Solution (continued)
The OSD does not appear on
the screen
Try to press the Menu button on the panel or
the remote control for 15 seconds to unlock
the OSD. Check the Menu Lock "Menu
Lock" on page 41.
The remote control is not
operating smoothly or works
only within a limited range
The battery may be low. Check if the laser
beam transmitted from the remote is too dim.
If so, replace the batteries with two new AAA
batteries.
Troubleshooting Your Projector
47
Changing the Lamp
The following message appears on the screen when your projector lamp is
approaching its end of life and needs to be changed:
Lamp is approaching the end of its useful life in full power operation.
Replacement suggested! Visit www.dell.com/lamps
CAUTION: Before you begin any of the procedures in this section, follow the
Safety Instructions as described on page 7.
To replace the lamp:
1 Turn off the projector and disconnect the power cable.
CAUTION: The lamp becomes very hot when in use. Do not attempt to replace
the lamp until the projector has been allowed to cool down for at least 30
minutes.
2 Let the projector cool for at least 30 minutes.
3 Loosen the two screws that secure the lamp cover, and remove the cover.
CAUTION: Do not touch the projector lamp or the lamp glass at any time.
Projector lamps are very fragile and may shatter if touched.
CAUTION: If the lamp shatters, remove all the broken pieces from the
projector and dispose or recycle according to state, local, or federal law. For
more information see - www.dell.com/hg.
4 Loosen the two screws that secure the lamp.
5 Pull the lamp up by its metal handle.
6 Replace with the new lamp.
7 Tighten the two screws that secure the lamp.
8 Replace the lamp cover and tighten the two screws.
Troubleshooting Your Projector
48
9 Reset the lamp usage time by selecting "Yes" for Lamp Reset in the OSD Lamp
tab. (See "LAMP" on page 38.)
CAUTION: Lamp Disposal (for the US only)
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE
RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL
LAWS. FOR MORE INFORMATION, GO TO WWW.DELL.COM/HG OR CONTACT
THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG. FOR LAMP
SPECIFIC DISPOSAL INFORMATION CHECK WWW.LAMPRECYCLE.ORG.
Troubleshooting Your Projector
49
5
Specifications
Light Valve
0.96" WUXGA DMD Type A,
DarkChip™3
Brightness
3850 ANSI Lumens (Max.)
Contrast Ratio
2700:1 Typical (Full On/Full Off)
Uniformity
85% Typical (Japan Standard - JBMA)
Number of Pixels
1920x 1200 (WUXGA)
Displayable Color
Up to 1.07B colors (with Dithering)
Color Wheel Speed
2X
Projection Lens
F-Stop: F/ 2.6~2.9
Focal length, f=39.12~46.94 mm
1.2X manual Zoom Lens
Projection Screen Size
20.9-301.0 inches (diagonal)
Projection Distance
3.28~39.37 ft (1 m~12 m)
Video Compatibility
Composite Video, S-Video, NTSC
(J/M/ 4.43MHz), PAL (B/D/G/H/I/M/N/
Nc/60), SECAM (B/D/G/K/K1/L),
HDMI, and Component video
(1080i/p, 720p, 576i/p, 480i/p)
compatibility
Composite video, Component video
(via VGA and YPbPr RCA), S-video,
and HDMI capability
Power Supply
Universal AC90-264 50/60 Hz with
PFC input
Power Consumption
454 watts in full mode, 405 watts in eco
mode
Audio
2 speakers, 5 watt RMS
Specifications
50
Noise Level
35 dB(A) Full-on mode, 32 dB(A) Eco
mode
Weight
13.4 lbs (6.08 kg)
Dimensions (W x D x H)
External 17.0 x 11.42 x 5.31 ± 0.04
inches (432 x 290 x 135± 1 mm)
Environmental
Operating temperature: 5oC - 35oC
(41oF- 95oF)
Humidity: 80% maximum
Storage temperature: 0oC to 60oC
(32oF to 140oF)
Humidity: 90% maximum
Regulatory
FCC, CE, UL, cUL, Nemko-GS, ICES003, GOST, NOM, SABS, SASO
I/O Connectors
Power: AC power input socket
Computer input: two D-sub for
analog/component, HDTV input
signals
Computer output: one 15-pin D-sub
Video input: one composite video
RCA, one S-video, and one set of
component video RCA
Audio input: one phone jack (diameter
3.5 mm)
Audio output: one phone jack
(diameter 3.5 mm)
USB port: one USB slave for remote
mouse support
One mini-DIN RS232 for wired remote
control from PC
HDMI input: two HDMI connectors
for HDMI signals (HDCP compliant).
One DisplayPort connector for
DisplayPort signals
One RJ45 connector for networking
Specifications
51
DC jack 12 volt@200mA output, relay
control for automatic projection screen
control
DC jack 5 volt@2.5A output, for
powering external devices
Lamp
264~300-watt user-replaceable lamp,
up to 2000 hours (up to 2500 hours in
eco mode)
NOTE: The actual operating life span of a projector lamp will vary according to
operating conditions and usage patterns. Usage of a projector in stressful
conditions which may include dusty environments, under high temperatures
and abrupt powering-off may result in a lamp's shortened operating life span or
possibly lamp failure. The lamp life specified for Dell's projectors refers to the
typical time under non-stressful operating conditions for more than 50% of a
sampling population to reduce to approximately 50% of the lamp's rated
brightness level. It is not the measure of time a lamp will cease light output.
Specifications
52
RS232 Pin Assignment
RS232 Protocol
•
•
Communication Settings
Connection settings
Value
Baud Rate:
19200
Data Bits:
8
Parity
None
Stop Bits
1
Command types
To pop up the OSD menu and adjust the settings.
•
Control command Syntax (From PC to Projector)
[H][AC][SoP][CRC][ID][SoM][COMMAND]
•
Example: Power ON Command (Send low byte firstly)
--> 0xBE, 0xEF, 0x10, 0x05, 0x00, 0xC6, 0xFF, 0x11, 0x11, 0x01, 0x00, 0x01
•
Control Commands List
To view the latest RS232 code, go to the Dell Support site at: support.dell.com.
Specifications
53
PIP Combination Sources
VGA-A
VGA-A
VGA-B
Component
HDMI-A
HDMI-B
DisplayPort
S-Video
/Composite
No
No
Yes
Yes
Yes
Yes
Yes
VGA-B
No
No
Yes
Yes
Yes
Yes
Yes
Component
Yes
Yes
No
Yes
Yes
Yes
Yes
HDMI-A
Yes
Yes
Yes
No
No
No
Yes
HDMI-B
Yes
Yes
Yes
No
No
No
Yes
DisplayPort
Yes
Yes
Yes
No
No
No
Yes
S-Video
/Composite
Yes
Yes
Yes
Yes
Yes
Yes
No
Specifications
54
Compatibility Modes (Analog/Digital)
Resolution
V. Frequency (Hz)
H. Frequency (KHz)
640X480
60
31.5
640X480
75
37.5
640X480
85
43.3
720X400
70.1
31.5
720X400
85
38
800X600
60.3
37.9
800X600
75
46.9
800X600
85.1
53.7
848X480
60
31
1024X768
60
48.4
1024X768
75
60
1024X768
85
68.7
1280X720
60
44.8
1280X768
60
47.8
1280X800
60
49.7
1280X1024
60
64
1280X1024
75
80
1280X1024
85
91.1
1360X768
60
47.7
1400X1050
60
65.3
1440X900
60
56
1600X1200
60
75
1680X1050
60
65.3
1920X1200-R
60
74
Specifications
55
Contacting Dell™
For customers in the United States, call 800-WWW-DELL (800-9993355).
NOTE: If you do not have an active Internet connection, you can find contact
information on your purchase invoice, packing slip, bill, or Dell product catalog.
Dell provides several online and telephone-based support and service
options. Availability varies by country and product, and some services may
not be available in your area. To contact Dell for sales, technical support,
or customer service issues:
1
Visit support.dell.com.
2
Verify your country or region in the Choose A Country/Region dropdown menu at the bottom of the page.
3
Click Contact Us on the left side of the page.
4
Select the appropriate service or support link based on your need.
5
Choose the method of contacting Dell that is convenient for you.
Contacting Dell™
56
Appendix: Glossary
ANSI LUMENS —A standard for measuring the brightness. It is calculated by
dividing a square meter image into nine equal rectangles, measuring the lux (or
brightness) reading at the center of each rectangle, and averaging these nine
points.
ASPECT RATIO —The most popular aspect ratio is 4:3 (4 by 3). Early television and
computer video formats are in a 4:3 aspect ratio, which means that the width of
the image is 4/3 times the height.
Brightness— The amount of light emitting from a display or projection display or
projection device. The brightness of the projector is measured by ANSI lumens.
Color Temperature— The color appearance of white light. Low color
temperature implies warmer (more yellow/red) light while high color temperature
implies a colder (more blue) light. The standard unit for color temperature is
Kelvin (K).
Component Video—A method of delivering quality video in a format that
consists of the luminance signal and two separate chrominance signals and are
defined as Y'Pb'Pr' for analog component and Y'Cb'Cr' for digital component.
Component video is available on DVD players.
Composite Video — A video signal that combines the luma (brightness), chroma
(color), burst (color reference), and sync (horizontal and vertical synchronizing
signals) into a signal waveform carried on a single wire pair. There are three kind of
formats, namely, NTSC, PAL and SECAM.
Compressed Resolution— If the input images are of higher resolution than the
native resolution of the projector, the resulting image will be scaled to fit the
native resolution of the projector. The nature of compression in a digital device
means that some image content is lost.
Contrast Ratio— Range of light and dark values in a picture, or the ratio between
their maximum and minimum values. There are two methods used by the
projection industry to measure the ratio:
1 Full On/Off — measures the ratio of the light output of an all white image (full
on) and the light output of an all black (full off) image.
2 ANSI — measures a pattern of 16 alternating black and white rectangles. The
average light output from the white rectangles is divided by the average light
output of the black rectangles to determine the ANSI contrast ratio.
Full On/Off contrast is always a larger number than ANSI contrast for the same
projector.
Glossary
57
dB— decibel—A unit used to express relative difference in power or intensity,
usually between two acoustic or electric signals, equal to ten times the common
logarithm of the ratio of the two levels.
Diagonal Screen— A method of measuring the size of a screen or a projected
image. It measures from one corner to the opposite corner. A 9FT high, 12FT
wide, screen has a diagonal of 15FT. This document assumes that the diagonal
dimensions are for the traditional 4:3 ratio of a computer image as per the example
above.
DisplayPort— A digital display interface standard developed by the Video
Electronics Standards Association (VESA). DisplayPort is designed for broad
application in PCs, monitors, TV displays, projectors, and other sources of display
content.
DLP®— Digital Light Processing™—Reflective display technology developed by
Texas Instruments, using small manipulated mirrors. Light passing through a color
filter is sent to the DLP mirrors which arrange the RGB colors into a picture
projected onto the screen, also known as DMD.
DMD— digital Micro- Mirror Device— Each DMD consists of thousands of
tilting, microscopic aluminum alloy mirrors mounted on a hidden yoke.
DVI-D— Digital Visual Interface-Digital connector.
Focal Length— The distance from the surface of a lens to its focal point.
Frequency— It is the rate of repetition in cycles per seconds of electrical signals.
Measured in Hz (Hertz).
HDMI— High Definition Multimedia Interface— A digital interface for audio and
video signals designed as a single-cable solution for home theater and consumer
electronics equipment.
Hz (Hertz)— Unit of frequency.
Keystone Correction— Device that will correct an image of the distortion
(usually a wide-top narrow-bottom effect) of a projected image caused by an
improper projector to screen angle.
Maximum Distance— The maximum distance from a screen the projector can be
to cast an image that is usable (bright enough) in a fully darkened room.
Maximum Image Size— The largest image a projector can throw in a darkened
room. This is usually limited by the focal range of the optics.
Minimum Distance— The closest position at which a projector can focus an
image onto a screen.
NTSC— National Television Standards Committee. North American standard for
video and broadcasting, with a video format of 525 lines at 30 frames per second.
Glossary
58
PAL— Phase Alternating Line. A European broadcast standard for video and
broadcasting, with a video format of 625 lines at 25 frames per second.
Reverse Image— Feature that allows you to flip the image horizontally. When
used in a normal forward projection environment, text, graphics, etc, are
backwards. Reverse image is used for rear projection.
RGB— Red, Green, Blue— typically used to describe a monitor that requires
separate signals for each of the three colors.
S-Video—A video transmission standard that uses a 4-pin mini-DIN connector to
send video information along two signal wires called luminance (brightness, Y)
and chrominance (color, C). S-Video is also referred to as Y/C.
SECAM— A French and international broadcast standard for video and
broadcasting, closely related to PAL but with a different method of sending color
information.
SVGA— Super Video Graphics Array,— 800 x 600 pixels count.
SXGA— Super Extended Graphics Array,—1280 x 1024 pixels count.
UXGA— Ultra Extended Graphics Array,—1600 x 1200 pixels count.
VGA— Video Graphics Array—640 x 480 pixels count.
WUXGA— Widescreen Ultra Extended Graphics Array,—1920 x 1200 pixels
count.
XGA— Extended Graphics Array— 1024 x 768 pixels count.
Zoom Lens— Lens with a variable focal length that allows the operator to move
the view in or out thereby making the image smaller or larger.
Zoom Lens Ratio— Is the ratio between the smallest and largest image that a lens
can project from a fixed distance. For example, a 1.4:1 zoom lens ratio means that
a 10 foot image without zoom would be a 14 foot image with full zoom.
Glossary
59
Index
A
Adjusting the Projected Image 22
Adjusting the Projector Height
22
lower the projector
Elevator button 22
Elevator foot 22
Tilt adjustment wheel 22
Adjusting the Projector Zoom and
Focus 23
Focus ring adjustment 23
Horizontal lens shift knob 23
Side door 23
Vertical lens shift knob 23
Zoom ring adjustment 23
Zoom tab 23
C
Changing the Lamp 48
Connecting the Projector
12V DC power cable 19
Automatic screen 19
Commercial RS232 control box
20
Composite video cable 15
Connecting a Commercial
RS232 Control Box 20
Connecting a Computer with a
DisplayPort cable 12, 13
Connecting a Computer with a
RS232 cable 10
Connecting a Computer with a
VGA Cable 9
Connecting a Computer with an
Ethernet cable 11
Connecting with a Component
(VGA to YPbPr) Cable 16
Connecting with a Component
(YPbPr to YPbPr) Cable 17
Connecting with a Composite
Cable 15
Connecting with an HDMI
Cable 18
Connecting with an S-video
Cable 14
Ethernet (RJ45) cable 11, 12
HDMI cable 18
Installing a Driving Automatic
Screen 19
Optional installation 19
Power cable 9, 10, 11, 12, 13,
14, 15, 16, 17, 18, 19, 20
RS232 cable 10, 20
S-video cable 14
To Computer 9
To DVD Player 14
USB to USB cable 9
VGA to VGA cable 9, 13
VGA to YPbPr cable 16
YPbPr to YPbPr cable 17
Connection Ports
12 Volt DC relay output 8
Index
60
5 Volt DC relay output 8
Audio input connector 8
Audio output connector 8
Component video input
connector 8
Composite video input
connector 8
DisplayPort connector 8
DVI-D input connector 8
HDMI input connector 8
Power cable connector 8
RS232 connector 8
Security cable slot 8
S-video input connector 8
USB remote connector 8
VGA-A input (D-sub) connector
8
VGA-B input (D-sub) connector
8
VGA-B output (monitor
loop-through) connector 8
Lens 7
Lens cap 7
O
On-Screen Display 29
Auto-Adjust 30
Display (in PC Mode) 35
Display (in Video Mode) 36
Input Select 29
Lamp 38
Language 39
Main Menu 29
Others 40
Picture (in PC Mode) 33
Picture (in Video Mode) 34
PIP Settings 37
Set Up 31
P
Contact Dell 26, 46
phone numbers 56
Control Panel 25
Powering On/Off the Projector
Powering Off the Projector 21
Powering On the Projector 21
D
Dell
contacting 56
M
Main Unit 7
Control panel 7
Elevator button 7
Focus ring 7
IR receiver 7
R
Remote Control 27
IR receiver 26
S
Specifications
Audio 50
Brightness 50
Index
61
Color Wheel Speed 50
Contrast Ratio 50
Dimensions 51
Displayable Color 50
Environmental 51
I/O Connectors 51
Lamp 52
Light Valve 50
Noise Level 51
Number of Pixels 50
PIP combination sources 54
Power Consumption 50
Power Supply 50
Projection Distance 50
Projection Lens 50
Projection Screen Size 50
Regulatory 51
RS232 Protocol 53
Uniformity 50
Video Compatibility 50
Weight 51
support
contacting Dell 56
T
telephone numbers 56
Troubleshooting 44
Contact Dell 44
Index
62