Craftsman 358.798980 Operator`s manual

___
Operator's Manual
CRRFTSMRN_
1.9 cu. in./32cc 2-Cycle
GASOLINE BLOWER/VACUUM
Model No.
358.798980
WARNING:
Read and follow all Safety Rules and Operating
Instructions before first use of this product.
For answers to your questions about this product:
Call 7 am-7 pro, Mon-Sat; Sun, 10 am-7 pm
1-800-235-5878
Sears. Roebuck
530-084301
and Co., Hoffman
03/16/96
Estates, IL 60179 USA
/
/
H
Limited Warranty Statement
Safety Rules
Assembly
Operation
Maintenance
Service & Adjustments
2
2
4
5
7
8
Storage
Troubleshooting
Parts List
Chart
Spanish
Parts and Ordering
9
t0
11
14
Back
FULL TWO YEAR WARRANTY ON SEARS BEST CRAFTSMAN" GAS BLOWER
For two (2) years from date of purchase, when this Gas Blower is maintained,
lubricated, and tuned up according to the instructions in the operator's manual,
Sears witl repair, free of charge, any defects in material or workmanship.
This warranty excludes blower tubes, spark plug, and air cleaner, which are expendable parts and become worn during normal use.
If this blower is used for commercial purposes, thiswarranty applies for 90 days from
the date of purchase. If this Blower is used for rental purposes, this warranty applies
for 30 days from the dale of purchase. This warranty applies only while this product
is in use in the United States.
WARRANTY SERVICE 1S AVAILABLE BY RETURNING THE BLOWER TO THE
NEAREST SEARS SERVICE CENTER IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights
which vary from slate to state.
Sears, Roebuck and Co. Dept. D/81TWA Hoffman Estates, IL 60179
Failure to follow all Safety Rules and Precautions can result in serious injury.
KNOW YOUR UNIT
• Read your Operator's Manual carefully until you completely understand
and can follow all wamings and
safety rules before operating the unit.
• Restrict unit to users who understand
and wil! follow all warnings and safety
rules in this manual.
PLAN AHEAD
• Always wear eye protection when operating, servicing, or performing
maintenance on unit. Wearing eye
protection will help to prevent rocks
or debris from being blown or ricocheting into eyes and face which can
result in blindness and/or serious in-
jury.
• Always wear respirator or face mask
when working with unit in dusty environments.
o Secure hair above shoulder length.
Secure or remove jewelry, loose
clothing, or clothing with loosely
-2-
hanging straps, ties; tassels, etc.
They can be caught in moving pads.
• Do nol operate the unit when you are
tired, ill, upset, or if you are under the
influence of alcohol, drugs, or me_cation.
• Keep children, bystanders, and animals away from work area a minimum of 50 feet (15 m) when starting
or operating unit.
• Inspect the area before starting the
unit. Remove all debris and hard objects such as rocks, glass, wire, etc.
that can ricochet, be thrown, or otherwise cause injury or damage during
operation.
HANDLE FUEL WITH CAUTION
- Eliminate al! sources of sparks or
flame (including smoking, open
flames, or work that can cause
sparks) in the areas where fuel is
mixed, poured, or stored,
. Mix and pour fuel in an outdoor area:
store fuel in a cool, dry, well ventilated place; use an approved,
marked container for all fuel purposes.
• Do not smoke while handling fuel or
while operating the unit.
, Do not fill fuel lank while engine is
running.
,, Wipe up luel spills before starting engine.
• Move at least 10 feet (3 meters)
away from fuel and fueling site before
starling engine.
OPERATE YOUR UNIT SAFELY
• Stop the engine before opening the
vacuum inlel door. The engine must
be stopped and the impeller blades
no longer lurning Io avoid serious injury Irom the rotating blades.
• Inspect unit before each use for
worn, loose, missing, or damaged
parts. Do not use until unit is in
proper working order.
• Keep outside surfaces free of oil and
fuel.
• Never slart or run engine inside a
closed room or building. Breathing
exhaust fumes can kill.
• To avoid static electricity shock, do
not wear rubber gloves or any other
insulated gloves while operating unit.
• Do not set unit on any surface except
a clean, hard area while engine is
running. Debds such as gravel, sand,
dust, grass, etc. could be picked up
by the air intake and thrown out
through discharge opening, damaging unit, property, or causing serious
injury to bystanders or operator.
• Avoid dangerous environmenls. Do
not use in unventilated areas or
where explosive vapors or carbon
monoxide build up could be present.
• Do not overreach or use from unstable surfaces such as ladders, trees,
steep slopes, rooftops, etc. Keep firm
footing and balance at all times.
• Never place ob.iects inside the blower
tubes; always direct the blowing debris away from people, animals,
glass, and solid objects such as
trees, automobiles, walls, etc. The
force of a_rcan cause rocks, dirt, or
sticks to be thrown or to ricochet
which can hurt people or animals,
break glass, or cause other damage.
• Never run unit without the proper
equipment attached. When using
your und as a blower, always install
blower tubes. When using your unit
as a vacuum, always install vacuum
tubes and vacuum bag assembly.
Make sure vacuum bag assembly is
completely zipped.
• Check air intake opening, blower
tubes, vacuum tubes, and elbow tube
frequently, always with engine
stopped and spark plug disconnected. Keep vents and discharge
tubes free of debris which can accumulate and restrict proper air flow.
• Never place any object in the air intake opening as this could restdct
proper air flow and cause damage to
the unit.
• Never use for spreading chemicals,
fertilizers, or other substances which
may contain toxic materials.
• To avoid spreading fire, do not use
near leaf or brush fires, fireplaces,
barbecue pits, ashtrays, etc.
• Use only for jobs explained in this
manual.
MAINTAIN YOUR UNIT PROPERLY
• Have all maintenance other than the
recommended procedures described
in the Operator's Manual pedormed
by Sears Service.
• Disconnect spark plug before performing maintenance except for carburetor adjustments.
° Use only recommended CRAFTSMAN® replacement parts; use of any
other parts may void your warranty
and cause damage to your unit.
• Empty fuel tank before storing the unit.
Use up fuel left in carburetor by starting
engine and letting it run until it stops.
• Do not use any accessory or attachment other than those recommended
by manufacturer for use with your unit.
• Do not store the unit or fuel in a
closed area where fuel vapors can
reach sparks or an open flame from
hol water heaters, electric motors or
switches, furnaces, etc.
,, Store in a dry area out of reach of
children.
SPECIAL NOTICE: For users on U.S.
Forest Land and in some states, including California(Public Resources
Codes 4442 and 4443), Idaho, Maine,
Minnesota, New Jersey, Oregon, and
Washington: Certain internal combustion engines operated on forest, brush,
and/or grass covered land in the above
areasarerequired
to be
equipped with
a spark arrestor, maintained in effective
working order, or the engine must be
constructed, equipped, and maintained
for the prevention of fire. Check with
your state or local authorities for regulations pertaining to these requirements. Failure to follow these requirements is a violation of the law. This unit
is not factory equipped with a spark arrestor; however, a spark arrestor is
available as an optional part. If a spark
arrestor is required in your area, contact Sears Service for the correct kit.
The spark arrestor, blower tubes, and
nozzles must be assembled to unff to
be in full compliance with regulations.
SPECIAL NOTICE: Exposure to vibrations through prolonged use of gaso-
line powered hand tools could cause
blood vessel or nerve damage in the
fingers, hands, and joints of people
prone to circulation disorders or abnormal swelling. Prolonged use in cold
weather has been linked to blood vessel damage in otherwise healthy
people. If symptoms occur such as
numbness, pain, loss of Strength,
change in skin color or texture, or loss
of feeling in the fingers, hands, or
joints, discontinue the use of this too!
and seek medical attention. An
ant!vibration system does not guarantee Ihe avoidance of these problems.
Users who operate power tools on a
COntinualand regular basis must monitor closely their physical condition and
the condition of this tool_
CARTON CONTENTS
Check carton contents against the following list.
Model 358.798980
• Blower
• Blower tube
• Nozzle
• Upper vacuum tube
• Lower vacuum tube
• Elbow tube
o Vacuum bag
° 2-Cycle Engine Oil
NOTE: It is normal for the fuel filter to
rattle in the empty fuel lank.
• Push the end of the elbow tube with
the grooves through the small bag
tube opening. Make sure the bag
tube opening is flush against the
raised rib in the middle of the tube.
• Close the zipper on the bag. Make
sure the zipper is closed completely
and the zipper seam is tucked toward
inside of the bag.
ASSEMBLY
WARNING:
If received assembled,
repeat a!l steps to ensure your unil is
properly assembled and all fasteners
are secure.
• No tools are required for assembly.
BLOWER TUBE ASSEMBLY
• Assemble the blower tube and nozzle
to the unit (turn clockwise to tighten).
0°%
Blower
Tube.
Slower
Outlet
_
_
B_
__Nozzle
VACUUM BAG ASSEMBLY
• Open the zipper on the vacuum bag
and insert the etbow tube.
Raised Si___
Bag Tube
Efbow_
Tube
Zipper
_
I
JI _
Opening
- _
_
_
Looped
Strap
VACUUM TUBE ASSEMBLY
WARNING Slop engine and be sure
the impairer blades have stopped turning before opening the vacuum inlet
door or attempting to insert or remove
the vacuum tubes. The rotating blades
can cause sedous injury.
,, Remove blower tube from engine.
= Insert a screwdriver into the latch
area on the vacuum inlet cover.
_r_l
_
sl_er
_ (_ ._ Vacuum
LA_'-J/7,-4, InletCover
• Gently tilt the handle of the screwdriver Iorward toward blower outlet while
pulling up on the vacuum inlet cover
with your other hand.
• Hold the vacuum inlet cover open until upper vacuum tube is installed.
• Align slanted end ol lower vacuum
tube as shown. Push lower vacuum
tube into upper vacuum tube.
• Assemble upper vacuum to unit; turn
clockwise to tighten,
• Insert the elbow tube into the blower
outlet, Make sure the elbow tube is
curved to the left.
• Turn lube counterclockwise to tighl-
• Slide the looped strap on the bag
over the upper vacuum tube.
• When converlJng back to the blower
feature, make sure latch on the vacuum inlet cover is securely fastened.
Elbow Tube
Curved To
The Left
Slanted
End
Vacuum Inlet Cover
Vacuum Inlet
eN.
KNOW YOUR BLOWER
READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE
OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize
yourself with the Iocalion of the various controls and adjustments. Save this
manual lot future reference,
!
ChokeLever Primer
Thrott/e Trigger
Bulb
FuelMix
Fitl Cap
BIower
Rear
Upper
_.
Vacuum
\
Bag
ElbowTube
I
Vacuum Tube_._
Lower
I
Vacuum Tube
_
I
ON/STOP Switch
'J-'--"
"P""
ON/STOP SWITCH
The ON/STOP switch is used to stop
the engine. The switch must be in the
ON position when starting the engine,
To stop the engine, move the switch to
the STOP position,
PRIMER BULB
The primer bulb removes air from the
fuel lines and fills them with lueL This
allows you to start the engine with lewer pulls on the starter rope. Activate the
primer bulb by pressing it and allowing
it to return to its onginal form.
THROTTLE LOCK
The throttle lock is used to hold the
throttle in the run and starting poslt=ons.
-5-
To activate throttle lock, squeeze and
hold throttle trigger, press and hold
throttte lock, then release throttle trigger,
THROTTLE TRIGGER
The throttle trigger controls engine
speed, Fully squeeze the trigger for full
speed operation.
CHOKE
The choke helps to supply fuel to the
carburetor during starting, This allows
you to start a cold engine. Activate the
choke by moving the choke lever to the
Full or Half position, After the engine
has started, move the choke lever to
the Off position,
•
I
Eye
Blower
Vacuum
BEFORE STARTING
ENGINE
WARNING:
Be sure to read the fuel
information in the safety rules before
you begin. If you do not understand the
safely rules, do not aflempt to fuel your
unit. Call 1-800-235-5878.
FUELING ENGINE
This engine is certified to operate on
unleaded gasoline, Before operation,
gasoline must be mixed with a good
quality 2-cycle air-cooled engine oil.
We recommend Craftsman brand oil.
Mix gasoline and oil at a ratio of 40: f
(A 40:1 ratio is obtained by mixing 3.2
ounces of oil with 1 gallon of unleaded
gasoline). DO NOT USE automotive oil
or boat oil. These oils will cause engine
damage. When mixing fuel, follow
instructions printed on container.
Once oil is added to gasoline, shake
container momentarily to assure that
the fuel is thoroughly mixed. Always
read and follow the safety rules relating
to fuel before fueling your unit.
IMPORTANT
Experience indicates that alcoho!
blended fuels (called gasohol or using
ethanol or methanol) can attract moisture which leads fo separation and
formation of acids during storage. Acidic gas can damage the fuel system of
an engine while in storage.
To avoid engine problems, empty the
fuel system before storage for 30 days
or longer, Drain the gas tank, start the
engine and let it run until the fuel lines
and carburetor are empty. Use fresh
fuel next season.
Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel
gum deposits during storage, CraBs-
-6-
man brand oil is already blended with
fuel stabilizer. See the STORAGE Section for additional information.
STOPPING YOUR ENGINE
• Move On/Stop switch to STOP.
, If engine does not stop. move the
choke to the Full position.
STARTING
YOUR ENGINE
BEFORE STARTING THE ENGINE
You MUST make sure the tubes are secure before using the unit,
• Fuel engine. Move el least 10 feet (3
meters) away from the fueling site.
• Hold the unit in the staffing position
as shown. Make sure the blower end
is directed away from people, animals, glass, and solid objects.
Stading Positions_
WARNING:
When startingengine, hold
the unit as illustrated.Do not set unit on
any sudace except a dean, hard area
when starting engine or while engine is
running. Debris such as gravel, sand.
dust, grass, etc. could be picked up by
the air intake and thrown out through the
discharge opening, damaging the unit or
property, or _using s.ed(yJs
iniu_to bystanders or the operator.
Throttle
/,,,,f
iwitch
I Throttle Lock
PrimerBulb
STARTING A COLD ENGINE OR A
WARM ENGINE AFTER RUNNING
OUT OF FUEL
• Move switch Io the ON position.
• Activate the throttle lock.
• Move choke to FULL position.
• Press primer bulb 6 times.
• Sharply pull starter rope 5 times.
NOTE: If the engine sounds as if it is
trymg to start before the 5th pull, go
to the next step.
• Move choke to HALF position.
• Pull starter rope sharply until engine
runs, but no more than 6 pulis.
NOTE: If engine has not started after 6
pulls, repeat all of the above steps.
, Allow engine to run for 15 seconds,
then move choke to OFF position.
• Squeeze and release the throttle trigger to allow engine to idle.
NOTE: If engine dies wdh choke at OFF
position, move the choke to the Half
position and pull the starter rope 6
more times. If engine does not start
and operate properly, refer to "Carburetor Adjustments."
• To stop eng=ne, move switch to OFF.
FOR A WARM ENGINE
• Move switch to the ON position.
• Move choke to OFF position.
• Activate the throttle lock.
CUSTOMER
• Press primer bulb 6 times.
• Sharply pull starter rope until engine
runs.
NOTE: If engine does not run after 5
pulls, it is probably flooded. Wait a few
minutes and repeat procedure with
choke at OFF.
• To stop engine, move switch to OFF.
DIFFICULT STARTING OR
STARTING A FLOODED ENGINE
Flooded engines can be started by
placing choke lever in the Off Choke
position and On/Stop switch in the On
position. Activate the throttle lock; then,
pull rope until engine starts. After the
engine starts, squeeze and release the
throttle trigger to allow engine to idle.
Starting could require pulling the starter
handle many times depending on how
badly unit is flooded. If unit still doesn't
start, refer to the TROUBLESHOOTING
chart or call 1-800-235-5878.
RESPONSIBILITIES
] CARE & MAINTENANCE
i Check lot Loose fasteners and parts
t Check for damaged or worn parts
I Clean unit and labels
TASK
WHEN TO PERFORM
Before each use
Belore each use
After each use
[ Clean air tilter
Replace spark plug
Every 5 hours of operation
Yearly
GENERALRECOMMENDATIONS
The warranty on this unit does not cover items that have been subjected to
operator abuse or negligence. To receive full value from the warranty, the
operator must maintain unit as instructed in this manual. Various adjustments
will need to be made periodically to
propedy maintain your unit.
CHECK FOR LOOSE
FASTENERS
AND PARTS
- Spark Plug Boot
• Air Filter
• Housing Screws
CHECK FOR DAMAGED
OR
WORN PARTS
Refer replacement of damaged/worn
parts to your Sears Service Center.
• On'Stop Switch - Ensure On/Stop
sw_tch functions properly by moving
the swntchtO the "Stop" position.
Make sure engine stops; then restart
engine and continue.
• Fuel Tank - Discontinue use of unit if
fuel tank shows signs of damage or
leaks.
• Vacuum Bag - Discontinue use of
vacuum bag if it is torn or damaged.
CLEAN UNIT & LABELS
• Clean the unit using a damp cloth
with a mild detergent,
• Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
Do nol clean filter in gasoline or other
flammable solvent. Doing so can
create a fire hazard or produce harmful
evaporative emissions.
Cleaning the air filter:
A dirty air filter decreases engine perIormance and increases fuel consumption and harmful emissions. Always
clean after every 5 hours of operation.
-7-
-----
cove,
• Clean the cover and the area around
it to keep debris from faTlinginto the
carburetor chamber when the cover
is removed.
* Remove parts as illustrated.
. Wash the filter in soap and water.
o Allow filter to dry.
• Replace parts.
We recommend att service and adjustments not listed in this manual be performed by your Sears Service Center.
REPLACE SPARK PLUG
Replace spark plug each year to ensure the engine starts easier and runs
better. Set spark plug gap at .025 in_
Ignition timing is fixed, nonadjustabre.
• Twist, then pull off spark plug boot.
• Remove spark plug from cylinder and
discard.
• Replace with Champion RCJ-8Y
spark plug and tighten with a 3/4 in.
socket wrench (10-12 ft.-Ibs).
• Reinstall the spark plug boot.
• Turn the idle speed screw clockwise
until it stops. Now turn counterclockwise 4-1/2 turns.
Start motor, let it run for 3 minutes, and
proceed to the adjustment section, if
engine does not start, refer to troubleshooting chart or call 1-800-235-5878.
If engine performance is acceptable at
the preset posffions, no further adjustments are necessary.
CARBURETOR
ADJUSTMENT
Carburetor adjustment is critical and if
done improperly can permanently damage the engine as well as the carburetor. If you require further assistance or
are unsure about performing this procedure, call our customer assistance
help line at 1-800-235-5878.
cove, .
Old fue!, a dirty air filter, a dirty tuel filter, or flooding may give the impression
of an improperly adjusted carburetor,
Check these conditions before adjusting the carburetor.
The carburetor has been carefully set
at the factory. Adjustments may be
necessary if you notice any of the following conditions:
(with Ltmiter Cap)
° Engine will not idle. See "Idle Speed"
ADJUSTING PROCEDURE
and "Mixture" under adjusting
Idle Speed "IDLE"
procedure.
Allow engine to idle. Adjust speed until
• Engine dies or hesitates instead of
engine runs without stalling.
accelerating. See "Acceleration
• Turn clockwise to increase engine
Check" under adjusting procedure.
speed if engine stalls or dies.
• Loss of power. See "Mixture" under
= Turn counterclockwise to decrease
adjusting procedure.
speed.
CARBURETOR
PRESETS
No further adjustments are necessary if
When making carburetor preset adjustperformance is satisfactory.
Mixture "MIX"
ments, do not force plastic limiter caps
beyond the stops or damage will occur. Allow engine to idle. Then accelerate
If carburetor presets are not needed.
the engine and note performance, tf
proceed to "ADJUSTING PROCEDURE,
engine hesitates, bogs down, or
Idle Speed."
smokes during acceleration, lure mixlure screw clockwise in 1/t6-tum increTO adjust presets:
• Turn the mixture screw countemlockments until performance is satisfactory.
wise until it slops,
Repeat this procedure as necessary
€
-8
for proper adjustment, After completing
adjustments,
check for acceleration,
Resel if necessary.
Acceleration Check
If engine dies or hesitates instead of
Prepare unit for storage at end of season or if it will not be used for 30 days
or more.
WARNING:
• Allow engine to cool, and secure the
unit before storing or transpoding.
• Store unit and luei in a well ventilated
area where fuel vapors cannot reach
sparks or open flames from water
heaters, electric motors or switches,
furnaces, etc.
• Store unit with all guards in place.
Position unit so that any sharp object
cannot accidentally cause injury.
• Store unit and fuel welt out of the
reach of children.
EXTERNAL
SURFACES
• If your unit is to be stored for a period
ol time, clean it thoroughly before
storage. SIore in a clean dry area.
• Lightly oil external melal sudaces.
FUEL SYSTEM
Under Fueling Engine in the Operating
Section of this manual, see message
labeled iMPORTANT regarding the use
ol gasohol in your engine.
Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel
gum deposits during storage. Add stabilizer to the gasoline in Ihe fuel tank or
-9-
accelerating, turn low speed mixture
adjustment counterclockwise until you
have smooth acceleration. Recheck
and adjust as necessary for acceptable
pedormance.
fuel storage container. Follow the mix
instructions found on stabilizer container. Run engine at least 5 minutes after
adding stabilizer.
CRAFTSMAN 40:1, 2-cycle engine oil
(air cooled) is already blended with fuel
stabilizer. If you do not use this Sears
oil, you can add a fuel stabilizer to your
fuel tank.
INTERNAL
ENGINE
• Remove spark plug and pour I teaspoon of 40:1, 2-cycle engine oil (air
cooled) through the spark plug opening, Slowly pull the starter rope 8 to
10 times to distribute oil.
• Replace spark plug with new one of
recommended type and heat range.
• Clean air filter.
• Check entire unit for loose screws,
nuts, and bolts. Replace any damaged, broken, or worn parts.
• At the beginning of the next season,
use only fresh fuel having the proper
gasoline to oil ratio.
OTHER
• Do not store gasoline from one season to another.
• Replace your gasoline can if it starts
to rust.
TROUBLESHOOTING
TROUBLE
Engine wilt not
start.
CHART
CAUSE
°
•
•
F•
i
Ignition switch off.
Engine flooded.
Fuel tank empty
Spark plug not fidng
i • Fuel not reaching
carburetor.
• Compression
E'ngine will not
idre properly.
•
;•
,•
i•
See "Starting Instructions"
Flittank with correct fuel mixture.
Install new spark plug
Check for dirty fuel filter; replace.
i
t
Check for kinked or split fuel line;
repair or replace.
low,
• Carburetor requires
adjustment.
* Crankshaft seals worn.
o Compression low.
Engine will not
accelerate,
tacks power, or
dies under a
load.
REMEDY
• Move Ignition switchtoON.
* Air filter dirty.
• Spark plug touted
• Carburetor requires
adjustment,
- Carbon build up
}_ See
Contact
Sears Service.
=Carburetor
Adjustments."
J
,, Contact Sears Service.
j • Contact Sears Service.
• Clean or replace air filter.
• Clean or replace spark plug
an{/re-gap.
• See "Carburetor Adjustments."
I , Contact Sears Service.
• Contact Sears Service.
• Compression low.
Enginesmokes
: excessively.
• Choke partially on.
, Fuel mixture incorrecL
I " Adjust choke.
i ° Empty fuel tank and reBI with
replace
air fitter.
f • Clean
correctorfuel
mixture.
, • See "Carburetor Adjustments."
Engine runs hot.
* Air filter dirty.
o Carburetor requires
adjustment.
- Fue! mixture incorrect.
• Spark plug incorrect.
• Carburetor requires
adjustment
, Carbon build up,
-10-
• See "Fueling Your Unit."
, Replace with correct spark plug.
I ° See =Carburetor Adjustments."
4 • Contact Sears Service.
REPAIR PARTS
.l=..i
=l
5O
23
\
40
- 24
" 25
48
29
44
34
33
28
Part No.
1
2
3
•4
5
6
7
8
9
1o
'H
12
t3
14
15
16
_7
18
19
2o
2)
22
23
24
25
530_0947t2
530-.026994
530-0291 t 1
530-.015635
530-029t
3g
530=015813
53G.._29072
530-_27597
530._015702
530-_9117
53C_=015840
530-024772
_7746
530-0477.56
530"-'019t 68
53G"_Bg572
530-029t
29
53O-029O89
530--0 t 581 a
530-047747
530-0t4347
530--Ot 4362
53G=014160
530-029728
530_3_9112
43
De_,c_iplion
Handle
Front |so_tor
S_3acer
S_Jew
Rear I SOJ,
at_
Screw
Tr,gger
Sprig
"C* C_
l"_o_le LOCk Button
p,n
5p-n o
ShtouO-Leff
Grommet
Switch
tsctator-Engme Mount
IsaLatot-Ta_
Screw
Fue_ Tank Assay
Fuet Calo Ass_/
Fuel P_k_Jo ASS y
H_rt_e Cove_ Ass'y
_=nc= 9 10& 12_
Cove_ -_t F_l{er
R_f.
26
27
28
29
30
31
32
33
34
35
36
37
38
3g
40
41
42
43
44
45
a6
47
4g
50
11
Fad
No.
530-0477_4
530-059293
530-029116
Champ,on
530-00_624
530-069626
530-039t 94
53O.--O39137
530_q15816
530-019178
530-325875
530-069349
530-015:=62
530_5843
530..039t9_
530-037492
530-.069303
5-30-_19232
_30-029404
530-0t 0960
530-023877
530069247
530-047854
530-0692 ",6
530-",047721
Pescdption
Assist Handle
Muffler Kit
Spring
Spark P_ug (RCJ-_Y)
Sc_'ew
Cylinder K_t
Lead Wire
lgnihon Mocl_e
Serew
Gaskel
PisIon'R,ng
Piston Kil flncl 36.38 & Pin)
Retainer
Screw
Ground Wi_e
Throttle Cable Ass'y.
Muffler Guard
Heat ShiekJ Gasket
Ai_ Baffle
Connecting Rod Ass'y
Vent Fitting
Line Kit - _erbJ;Purge
Vent Fd(ing
Line K_t- Tank/Purge
Purge Bulb
ii
iii i
REPAIR PARTS
7
8
9
10
34
35
45 46
47
48
51
52
54"
S6
57
REPAIR PARTS
Assern_v part Number 530-069130 (WA2;9_
2
KIT
KIT
//
KIT ._
KIT
I'tJT,_.. _
;_TK_ T
KIT
J
1
Key
NO
1
P_rt
No.
Descrlpb_
530-069729
Carburelor
530038403
(KiT = Can'Le,',ts)
L_-t _t_" Cap-S_gle
KEY NO.
,,,,,,,
,,
'_
2
3
13
Reoa_" Kit
PART
Ne_le
NO.
DESCRIPllON
53G-.095358
53_037250
530--069750
Coltecfion Bag
Shoulder SIrap
Vacuum Tube
530-03855S
530-095117
Tube & Nozzle ASS'y.
Elbow