Sharp FU-60SE Specifications
Add to my manuals36 Pages
Sharp FU-60SE is an air purifier with Plasmacluster Ion Control, HEPA Filter, and Washable Active Carbon Filter. It purifies the air, removing dust, pollen, mold, and odor. It also has a SENTINEL Operation Mode that detects favorable conditions for airborne microbes and releases Plasmacluster Ions to control their activity.
advertisement
Free Standing
*Plasmacluster is a trademark of
Sharp Corporation.
*Plasmacluster
R
FU-P60S
AIR PURIFIER
OPERATION MANUAL
ENGLISH
FEATURES
Plasmacluster Ion Control
The unit controls the ratio of negative ions and positive ions depending on the condition of the room.
• Clean Mode
Approximately the same numbers of positive and negative ions are discharged.
This mode is effective for reducing some airborne mold.
• Ion Control Mode
Plenty of negative ions exist in natural surroundings such as waterfalls or forests.
In this mode, negative ions will be released in an increased rate, in order to bring the room air close to this natural environment.
• AUTO Plasmacluster Ion Mode
The unit will switch between Clean Mode and Ion Control Mode automatically depending on the amount of impurities in the air detected by the dust and odour sensors.
• SENTINEL Operation Mode
The “SENTINEL” function detects any air enviornment that is favourable for activation of mold, virus and allergen using its 4 sensors for dust, odour, temperature and humidity, and it releases
Plasmacluster Ions to create an environment that controls the activity of airborne microbes.
• Filters
1) Pre-Filter
It collects large particles.
2) Washable Active Carbon Filter
Its deodorizing performance can be maintained by washing.
3) HEPA (High Efficiency
Particulate Air) Filter with
Microbial Control Filter
High-efficiency particle collection including pollen and dust.
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .... E-2
• WARNING ....................................................
E-2
• CAUTIONS CONCERNING OPERATION ...
E-2
• REMOTE CONTROL LIMITATIONS ............
E-2
• INSTALLATION GUIDELINES .....................
E-3
• FILTER GUIDELINES ..................................
E-3
• HOW SHARP AIR PURIFIER WORKS ........
E-3
PART NAMES .......................................... E-4
• MAIN UNIT DISPLAY ...................................
E-4
• INCLUDED ...................................................
E-4
• BACK ...........................................................
E-4
PREPARATION........................................ E-5
• INSERTING BATTERIES
IN THE REMOTE CONTROL ......................
E-5
• REMOTE CONTROL USE ...........................
E-5
• FILTER INSTALLATION ...............................
E-6
OPERATION ............................................ E-8
• MAIN UNIT OPERATION .............................
E-8
• REMOTE CONTROL OPERATION ..........
E-10
CARE AND MAINTENANCE ................. E-11
• MAIN UNIT .................................................
E-11
• ODOUR SENSOR / DUST SENSOR .........
E-11
• FILTER CLEANING ....................................
E-11
• WASHABLE ACTIVE CARBON
FILTER CARE ...........................................
E-12
• FILTER REPLACEMENT
GUIDELINES ............................................
E-13
TROUBLESHOOTING ........................... E-14
SPECIFICATIONS ................................. E-15
Thank you for purchasing the SHARP Air Purifier. Please read this manual carefully for the correct usage information. Before using this product, be sure to read the section: “Important Safety Instructions.”
After reading this manual, retain it in a convenient location for future reference.
E-1
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
WARNING
- To reduce the risk of electrical shock, fire or injury to persons:
• Read all instructions before using the air purifier.
• Use only a 220 volt outlet.
• Do not use the air purifier if the power cord or plug is damaged or the connection to the wall outlet is loosen.
• Periodically remove dust from the power plug.
• Do not insert fingers or foreign objects into the intake or air outlet.
• When removing the power plug, always hold the plug and never pull the cord.
Electrical shock and/or fire from short circuit may occur as a result.
• Do not remove the power plug when your hands are wet.
• Do not use this air purifier near gas appliances or fireplaces.
• Remove the power plug from the wall outlet before cleaning the unit and when not using the unit.
Electrical shock from bad insulation and/or fire from short circuit may occur as a result.
• If the power cord is damaged, it must be replaced by the manufacturer, its service agent,
Sharp authorized service or similarly qualified person in order to avoid a hazard.
• Do not operate when using aerosol insecticides or in rooms where there is oily residue, incense, sparks from lit cigarettes, chemical fumes in the air or under a humid condition.
• Use with care when cleaning the air purifier. Strong corrosive cleansers may damage the exterior.
• Only Sharp Authorized Servicers should service this air purifier. Contact the nearest Servicer for any problems, adjustments, or repairs.
• The batteries must be removed from the remote control before disposal, and the batteries must be disposed of safely.
CAUTIONS CONCERNING OPERATION
• Do not block the intake and air outlet.
• Do not use the unit near or on hot objects, such as range or where it may come into contact with steam.
• Always hold the handle on the back of the main unit when moving it.
• Holding the front panel when carrying may cause it to detach, thus dropping the unit and resulting in bodily injury.
• Do not operate the unit without the filter.
Not only it does not improve filter performance, it may cause electric shock or malfunction.
• Clean the exterior with a soft cloth only.
The unit surface may be damaged or cracked.
In addition, the sensor may malfunction as a result.
REMOTE CONTROL LIMITATIONS
DO NOT USE THE REMOTE CONTROL IN THE FOLLOWING LOCATIONS:
• Any location where there is inverter lighting equipment or electronic spontaneous lighting equipment
The remote control may become inoperative. In this case, move away from such lighting equipment or change direction.
• Location exposed to direct sunlight or fluorescent.
The unit may not receive signals from the remote control.
E-2
INSTALLATION GUIDELINES
• During the operation of the product, please place the unit at least 2m away from equipments which involve electric wave such as televisions, radios or wave clocks, in case electrical interference occurs to such equipment.
• Leave at least 60cm of space from the wall.
The motor may overheat, causing a malfunction.
• Avoid a location where the sensor is exposed to direct wind.
The unit may not operate properly.
• Avoid locations where curtains, etc., come into contact with the intake or air outlet.
Curtains, etc., may become dirty or a malfunction may occur.
• Avoid locations where the unit is exposed to condensation, due to drastic temperature changes.
• Place on a stable surface with sufficient air circulation.
• Do not install when there is generation of lampblack, such as in a kitchen, etc.
The unit surface may crack or the sensor may malfunction as a result.
• The wall behind the air outlet may become dirty as time passes. When using the unit for extensive period in the same location, use a vinyl sheet, etc., to prevent the wall from becoming dirty. In addition, periodically clean the wall, etc.
FILTER GUIDELINES
• Follow the instructions in this manual for correct care and maintenance of the filters.
HOW SHARP AIR PURIFIER WORKS
An air purifier draws in room air from its air intake, lets the air pass through an Active Carbon Filter
(Deodorizing Filter) and a HEPA Filter (dust collection filter) inside of the unit, then discharges the air from its air outlet. The air purifier repeats this process by moving its internal fan.
As air passes through, the HEPA Filter can remove dust particles. The Active Carbon Filter gradually absorbs odour elements as they repeatedly pass through the filter.
(Odour elements are absorbed by HEPA Filter as well.)
Some odour ingredients absorbed by the filters may become separated and may be discharged through the air outlet and result in additional odour. Depending on the usage environment, this odour may become strong in a shorter period than expected.
In this case, purchase the optional replacement filter kit FZ-P60SEF.
NOTE
• The air purifier is designed to remove air-suspended dust and odour, but not harmful gases (for example, carbon monoxide contained in cigarette smoke). If the odour sources still exist, it cannot completely remove the odour.
(for example, odours from construction materials and pet odours).
• It is suggested to open the window a bit when you are smoking in order to facilitate ventilation.
HEPA Filter
Active Carbon Filter
E-3
PART NAMES
MAIN UNIT DISPLAY
Remote Control Receiver
Filter Indicator Light
SENTINEL Operation Indicator Light
CLEAN-SIGN Light
Plasmacluster Indicator
Light
Remote Control
INCLUDED
Remote Control (1 unit)
Battery (AA battery x 2 )
• Operation manual
AUTO Operation Indicator Light
15min. HIGH operation Indicator
Light
Pollen Mode Indicator Light
Fan Speed Indicator
Lights
OFF Timer Display Indicator Lights
Sensor Sensitivity
Select Switch
Sensor sensitivity can be adjusted to “Normal” or
“SENSITIVE” by this switch.
Filter Reset Button
Front Panel
Hook
POWER ON/OFF Button
MODE Button
Temperature/Humidy Sensor
Odour Sensor
Dust Sensor(Dust Sensor Cover)
Main Unit
Filter Frame
HEPA Filter (white)
Washable Active Carbon Filter (black)
Pre-Filter
BACK
Handle
Air Outlet
Date Label
Power Cord
Power Plug
E-4
PREPARATION
INSERTING BATTERIES IN THE REMOTE CONTROL
1 Remove the back cover
Press and slide the back cover to remove.
2
Insert batteries
Insert batteries with and as shown below.
3
Close the back cover
Battery Information
• The battery life is about 1 year.
• The batteries for this remote control are for initial use only . Change the batteries when necessary.
• Incorrect usage of the batteries may cause battery fluid leakage and/or damage.
Take care of the following when handling:
• When replacing the batteries, replace both batteries with new ones of the same type. (Use 2 AA manganese batteries.)
• When not using the unit or remote control for an extended period, remove the batteries.
• The batteries are for initial use only and may be depleted within 1 year.
REMOTE CONTROL USE
• Operate the remote control facing the main unit receiver.
• The signal range is about 7m.
• Make sure there are no objects blocking the path of the signal.
• A beep sound will be heard from the main unit when a signal is received.
Transmitter
Receiver
NOTE
• Avoid dropping or damaging the remote control, using in a high humidity condition, in direct sunlight or near a heat source.
E-5
PREPARATION
Be sure to remove the power plug from the wall outlet.
FILTER INSTALLATION
To maintain the quality of the filters, they are installed in the main unit within the plastic bags. Be sure to remove the filters from the plastic bags before using the unit.
1
Remove the filters
1
Remove the Front
Panel.
Pull the bottom of the Front
Panel.
2
Front Panel
1
Hook
1
2
Pull out the Filter Frame and remove the Pre-Filter,
Active Carbon Filter and HEPA Filter.
2
1
1
Filter Frame
Pre-Filter
2
3
Remove the Active Carbon Filter
(black) and HEPA Filter (white) from the plastic bags.
Active Carbon Filter
HEPA Filter
Pre-Filter
Active Carbon Filter
HEPA Filter
Filter Frame
E-6
outlet.
Tabs 2
Install the filters
1
Place the HEPA Filter within the Filter Frame with the tabs facing up.
Do not install the filter backwards or the unit will not operate properly.
2
Place the Active Carbon Filter on top of the HEPA Filter with the bands (2 places) facing up.
HEPA Filter
Filter Frame
Band
Active Carbon Filter
HEPA Filter
Filter Frame
3
Place the Pre-filter through the bands (2 places) located at the corners of the Active
Carbon Filter.
Insert the tabs of the pre-filter into the associated holes of the Filter
Frame.
Band
4
Mount the Filter Frame to the main unit.
Holes
Main unit
Filter Frame
Band
5
Fill in the usage start date on the Date Label.
Use the date as a guide for the
Filter Replacement schedule.
Date Label
Tabs (4 places)
E-7
OPERATION
MAIN UNIT OPERATION
Filter Indicator Light
SENTINEL Operation Indicator Light
Clean-Sign Light
Plasmacluster Indicator Light
Main Unit Controls
• AUTO
• 15 min. HIGH
• POLLEN
• SILENT
• NORMAL
• MAX
MODE Button
Power ON/OFF Button
2
1
Plasmacluster
1
2
Power ON/OFF Button
• Used to start operation (short beep) and stop operation (long beep)
• Plasmacluster Indicator Light and Fan Speed Indicator Light turn on/off.
• Unless unplug the power cord, the operation starts in the previous mode the unit was operated in.
MODE Button
• The operation mode can be switched.
AUTO operation
The fan speed is automatically switched
(HIGH*, NORMAL, SILENT) depending on the amount of pollution in the air. The sensors detect the pollution for efficient air purification.
MAX operation
The unit will operate at a fan speed of MAX.
15 min. HIGH
*
operation
The unit will operate at HIGH* fan speed for 15 minutes, then will operate at Auto operation.
The operation mode is effective when quick removal of impurities in the air is desired.
NORMAL operation
The unit will operate at a fan speed of NORMAL.
POLLEN mode operation
The unit will operate at HIGH* fan speed for 10 minutes, then will alternate between NORMAL and HIGH for 20 minutes.
10 minutes: HIGH fan speed
20 minutes: NORMAL fan speed
20 minutes: HIGH fan speed
SILENT operation
The unit will operate quietly using minimal air intake.
* HIGH fan speed is an intermediate speed be tween NORMAL and MAX.
E-8
SENTINEL Operation Indicator Light
When Plasmacluster Ion mode is ION AUTO or CLEAN mode, SENTINEL Operation is ready to be activated, and when SENTINEL Operation is in active, the Plasmacluster Indicator Light (blue) turns on and repeats its colour cycles between dark and light, and also the SENTINEL Operation Indicator Light
(green) turns on.
The “SENTINEL” function detects any air environment that is favourable for activation of mold, virus and allergen using its 4 sensors for dust, odour, temperature and humidity, and it releases Plasmacluster
Ions to create an environment that controls the activity of airborne microbes.
The fan speed and amount of Plasmacluster Ions are automatically increased during AUTO operation, while only the amount of Plasmacluster Ions is automatically increased during manual fan control mode and Pollen mode.
PLASMACLUSTER INDICATOR LIGHT
Plasmacluster ion operation is selected using the remote control.
Blue light
When the Plasmacluster ion operation is in Clean Mode, or in AUTO Plasmacluster Ion Mode and the air in the room is impure, this light will be activated and the unit will operate in Clean Mode.
Green light
When the Plasmacluster ion operation is in the Ion Control Mode, or in AUTO Plasmacluster Ion Mode and the air in the room is clean, this light will be activated and the unit will operate in Ion Control Mode.
Light off
There are no Plasmacluster ions being generated.
• The light can be turned off by using the ‘Display ON/OFF Button’ on the Remote Control. In this case,
Plasmacluster ions are generated.
(Please turn off the light when not required.)
CLEAN-SIGN LIGHT
The colour changes according to the air condition.
Clean (Green) Slightly Impure (Orange) Very Impure (Red)
ABOUT THE CLEAN-SIGN
• The condition of the CLEAN-SIGN depends on the room air condition detected by the Dust and Odour
Sensor when the plug is inserted into the wall outlet.
• It is possible to have a green CLEAN-SIGN with impurities in the air at the time that the air purifier was just introduced to the room environment. After a while, however, the base impurity rate will be adjusted to detect room air condition correctly.
• Use the Display ON/OFF Button on the remote control to turn off the Indicator light.
DETERMINING THE BASE IMPURITY RATE
For the first 30 seconds after the power plug is inserted into the wall outlet, the unit will check the conditions of the air. If operation is set to ON during this time, the CLEAN-SIGN LIGHT will alternately flash in green, orange and red.
FILTER INDICATOR LIGHT
Clean the Active Carbon Filter when the Filter Indicator Light is on.
(The indicator light will be activated in about 2 months, when using the unit for 24 hours a day.)
(See Page E-12)
E-9
OPERATION
REMOTE CONTROL OPERATION
POWER ON/OFF Button
• When you press the
POWER ON/OFF Button, a short beep will sound and operation will start in AUTO
Mode.
• Unless unplug the power cord, the operation starts from the previous mode the unit was operated in.
• To stop, press the POWER
ON/OFF Button again.
A long beep will sound and operation will stop.
Auto (Fan Speed) Button
The fan speed switches automatically depending on the amount of impurities in the air.
Manual (Fan Speed) Button
The fan speed can be switched among Silent,
NORMAL and MAX settings.
15 min. HIGH Button
See page E-8
Display ON/OFF Button
Switches the Plasmacluster
Indicator Light and CLEAN-
SIGN Light either ON or OFF.
Plasmacluster
Operations available with the Remote Control
• AUTO
• MANUAL
• POLLEN
• OFF TIMER
• 15 min. HIGH
• DISPLAY ON/OFF
Plasmacluster Ion mode selections
• AUTO
• CLEAN
• ION CONTROL
• OFF
Transmitter
Filter Reset Button
When the Washable Active Carbon Filter is cleaned and reinserted into the main unit, press the Filter Reset Button.
Pollen Mode Operation
Button
See Page E-8
Off Timer Button
The set time switches every time the button is pressed as shown below.
1 hour 4hours
Cancel 8 hours
• The indicator light shows the remaining time.
• The unit will stop operation when the timer is up.
Plasmacluster Ion Mode Selections
AUTO
When pressed, the unit will switch between Clean
Mode and the Ion Control Mode automatically depending on the amount of impurities in the air as detected by the dust and odour sensors. Clean
Mode will operate for 1 minute when the Auto function is selected.
(CLEAN)
When pressed, the unit will constantly operate in the Clean Mode, in which the same numbers of positive and negative ions are discharged. The
Plasmacluster Indicator Light is blue.
(ION CONTROL)
When pressed, the unit will constantly operate in
Ion Control Mode.
The Plasmacluster Ion Indicator Light is green.
OFF
The generation of ions will be ceased and the Plasmacluster Indicator Light will go out.
E-10
CARE AND MAINTENANCE
To maintain optimum performance of this air purifier, please clean the unit including the sensors and filters periodically.
When cleaning the unit, be sure to unplug the power cord, and never handle the plug with wet hands. Electrical shock and/or bodily injury may occur as a result.
MAIN UNIT
To prevent dirt or stains on the main unit, clean as often as necessary. If stains are allowed to remain, they may become hard to clean.
Wipe with a dry, soft cloth
For stubborn stains or dirt, use a soft cloth dampened with warm water.
Do not use volatile fluids
Benzene, paint thinner, polishing powder, etc., may damage the surface.
Do not use detergents
Detergent ingredients may damage the unit.
Keep the unit away from water
ODOUR SENSOR / DUST SENSOR
The sensitivity of the sensor will become unstable if the odour/dust sensor is dirty or blocked. Remove dust from the surfaces of the sensor openings using a vacuum cleaner.
Hole of odour sensor
Hole of dust sensor
Sensor Filter
Detach the sensor filter and tap it lightly with your hand to remove the dust. If it is very dirty, wash it with water and then allow it to dry thoroughly.
Sensor Filter
It does not have a front and a back.
FILTER CLEANING
Remove the Front Panel, Clean the surface of the Pre-Filter lightly with a vacuum cleaner.
If it is contaminated heavily, remove it from the Filter Frame and wash it.
NOTE
• In case of washing, use a soft brush etc. and cold/warm water.
• Metal brushes or scrub brushes may cause damage.
• After washing, leave it in the shade until it gets dried.
Then place it back to the frame.
• Never wash or clean the HEPA Filter using the nozzle of a vacuum cleaner directly.
This will greatly decrease the performance of the filters.
E-11
CARE AND MAINTENANCE
WASHABLE ACTIVE CARBON FILTER CARE
HAND WASH ONLY!
DO NOT TUMBLE DRY!
5
Remove excess water
The filter will be saturated with water after rinsing. To decrease drying time, wrap the filter in an old thick towel so that excess water can be removed.
Care Cycle
When the Filter Indicator Light lights up, this indicates that the filter needs to be cleaned. If the unit is kept on 24 hours a day then the Filter Indicator Light will be activated in about 2 months.
The Filter Indicator Light is for reference.
Clean the filter as often as necessary when odour persists.
CAUTION
Some carbon may adhere to the towel, but it is harmless.
1 Remove visible dirt with a vacuum cleaner.
6 Dry the filter outdoors if possible in a well ventilated area.
2
3
Fill a large container up with warm water, add a mild kitchen detergent and stir.
Dilute as indicated on the detergent container.
Allow the filter to soak approximately 30 minutes before washing.
If the filter surface is very dirty, scrub with an old toothbrush.
7
CAUTION
• The wet filter is heavy. Fix it securely for drying to make sure it does not fall down.
• The filter takes longer to dry in winter, on rainy days.
Wash it on a day when the weather is good and dry it in the sun.
Move it indoors at night to prevent freezing.
• Dry the filter outdoors in a well ventilated area. If dried indoors, the water dripping off the filter may soil your floor.
• Make sure that the activated carbon has not shifted to one side inside the filter. If it has, distribute it evenly with your fingers.
• Let the filter dry thoroughly.
If used while the filter is still moist, then the air that is exhausted from the main unit will have an odour.
It may take 1 or 2 days to dry.
Reinstalling the Filter.
Reinstall the filter as shown on Page E-6,7
4
CAUTION
Handle with care to prevent damage to the activated carbon particles.
Rinse thoroughly with clean water
8 Once the Active Carbon Filter has been cleaned, connect the power cord to the outlet and press the Filter
Reset Button on either the Remote
Control or Main Unit.
• Once the Filter Reset Button has been activated, you will hear a beep sound that means the unit has been reset.
• The Filter indicator light will then go out automatically.
CAUTION
If rinsing in a container, be sure to rinse 3 to 4 times so that the odour is rinsed thoroughly from the filter.
Filter Reset Button
E-12
FILTER REPLACEMENT GUIDELINES
Depending on the usage environment, air outlet odour may become strong after several months.
If dust or odours cannot be removed easily, replace the filters.
(Refer to HOW SHARP AIR PURIFIER WORKS E-3)
Guide for filter replacement timing
• The following filter life and replacement period is based on the condition of smoking 10 cigarettes per day and the dust collection/deodorization power is reduced by half compared with that of new filters.
We recommend to replace the filters more frequently if the product is used in a condition significantly severer than normal household use.
• HEPA Filter About 5 years after opening
• Active Carbon Filter About 5 years after opening
REPLACING THE FILTERS
1
See page E-6,7 for directions on how to install the filters when replacing.
2
After replacing the filters:
Be sure to press the Filter Reset Button on the
Remote Control with the power cord connected to the outlet.
A short beep will be heard and the operation hours stored in the memory will be reset.
The Filter Indicator Light will then go out automatically.
3
Fill in the usage start date of the filters on the Date Label
.
Replacement Filters
Model: FZ-P60SEF
• HEPA Filter : 1 unit
• Active Carbon Filter: 1 unit
Please consult your dealer for purchase of replacement filters.
Date Label
Disposal of Filters
Please dispose of replaced filters according to the local disposal laws and regulations.
HEPA Filter materials:
• Filter: Polypropylene
• Frame: Polyester
• Microbial Control Filter: Polypropylene, Polyethylene
Active Carbon Filter Materials:
• Deodorizer: Activated charcoal
• Net: Polypropylene 60%, Polyester 40%
E-13
TROUBLESHOOTING
Before calling for repair, please review the list below, since the problem may not be a unit malfunction.
SYMPTOM REMEDY (not a malfunction)
The Remote Control does not work
Odours and smoke are not removed
The CLEAN-SIGN Light lights green even when the air is impure
• Have the batteries been depleted?
• Are the batteries inserted correctly?
• Is a fluorescent lighting in the room flickering due to service life?
• Clean or Replace the filters if they appear to be heavily soiled.
(Refer to E-12,E-13)
• The air could be impure at the time the unit was plugged in.
(Refer to E-9)
The CLEAN-SIGN Light lights orange or red even when the air is clean
• The sensitivity of the sensor becomes unstable when the opening of the odour sensor is dirty or is clogged.
Clean the dust around the sensor opening using a vacuum cleaner. (Refer to E-11)
The Plasmacluster Indicator
Light remains green (or blue) and does not change
A clicking or ticking sound is heard from the unit
• When in Clean Mode ( or Ion Control Mode), the Plasmacluster
Indicator Light colour will not change.
The discharged air has an aroma or odour.
The unit does not operate when cigarette smoke is in the air.
The Filter Indicator Light remains activated even after replacing filter.
• Clicking sound is emitted when the unit is in the Ion Control
Mode, and ticking sound is emitted when the unit is generating ions.
If the sound is irritating, set the unit away from you.
• Check to see if the filters are heavily soiled.
Replace the filters.
• Plasmacluster Air Purifiers emit small traces of ozone which may produce an odour. The amount of ozone emitted by the ion generator is very little which is below the safety levels set by the IEC 60335-2-65, and it is harmless to the human body.
• Is the unit installed in a location that is difficult for the sensor to detect cigarette smoke?
• Are the odour sensor openings blocked or clogged?
(In this case, clean the openings.) (Refer to E-11)
• After replacing filters, connect the power cord to an outlet and press the Filter Reset Button on the remote control. (Refer to
E-12)
The Plasmacluster Indicator
Light or the CLEAN-SIGN Light will not activate.
• Check to see if the Display OFF Mode on the Remote Control is selected. If so, press the Display ON/OFF Button on the
Remote Control to activate the indicator light.
(Refer to E-10)
ERROR DISPLAY
LAMP INDICATION
The “Silent” Fan Speed Indicator Light blinks.
REMEDY
Fan motor disconnected or abnormal.
Operation stops.
• Pressing the ON/OFF button will reset the error display, but if error occurs again, contact the shop where you purchased the unit.
E-14
SPECIFICATIONS
Fan
Speed
Operation
Model
Power supply
Fan speed level
Rated power
Air Flow Volume
Applicable floor surface
Cord Length
Dimensions
Weight
MAX
65 W
360 m 3 /hour
FU-P60S
220V 50Hz
NORMAL
9.6 W
138 m 3 /hour
~46m 2 *
2.5m
415mm(W)x241mm(D)x572mm(H)
8.5kg
SILENT
4.0 W
36 m 3 /hour
* The applicable floor surface area is the surface area for operating the unit in MAX fan level.
• Applicable floor surface area indicates the space where a certain amount of dust particle can be removed in 30 minutes.
Standby Power
In order to operate the electrical circuits while the power plug is inserted in the wall outlet, this product consumes about 0.7W of standby power.
For energy conservation, unplug the power cord when the unit is not in use.
E-15
FU-P60S_HK_1.
2 6/3/2005, 11:24 AM
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
¥…'RƒW-1 3
C-1
6/3/2005, 5:10 PM
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
FU-P60S_HK_1.
4
C-2
6/3/2005, 11:25 AM
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
FU-P60S_HK_1.
5
C-3
6/3/2005, 11:25 AM
HEPA Filter
Active Carbon Filter
¥…'RƒW-1 6
C-4
6/3/2005, 5:10 PM
1
2
3
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
FU-P60S_HK_1.
7
C-5
6/3/2005, 11:25 AM
1
1
2
2
1 1
2
1
2
1
3
FU-P60S_HK_1.
8
C-6
6/3/2005, 11:25 AM
2
1
2
3
4
5
FU-P60S_HK_1.
9
C-7
6/3/2005, 11:25 AM
1
•••••
•••••
•••••
2
•••••
Plasmacluster
•••••
•••••
•••••
•••••
•••••
•••••
2
1
¥…'RƒW-1 10
C-8
6/3/2005, 5:11 PM
•••••
•••••
•••••
•••••
OPERATION
¥…'RƒW-1 11
C-9
6/3/2005, 5:11 PM
•••••
•••••
•••••
Plasmacluster
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
FU-P60S_HK_1.
12
C-10
6/3/2005, 11:26 AM
•••••
•••••
•••••
•••••
FU-P60S_HK_1.
13
C-11
6/3/2005, 11:26 AM
5
1
2
3
4
6
7
8
•••••
•••••
•••••
•••••
•••••
•••••
•••••
FU-P60S_HK_1.
14
C-12
6/3/2005, 11:26 AM
•••••
•••••
•••••
1
2
•••••
•••••
3
•••••
•••••
•••••
•••••
C-13
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
•••••
FU-P60S_HK_1.
16
•••••
C-14
6/3/2005, 11:26 AM
•••••
FU-P60S_HK_1.
17
C-15
6/3/2005, 11:26 AM
FU-P60S-P30 1 05.6.3, 0:06 PM
MEMO
FU-P60S-P31 1 05.6.3, 0:06 PM
SHARP CORPORATION
TINS-A154KKRZ 05FO CN 2
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project