Mitsubishi XL7000U User manual

LCD Projector
XL7100U
Controlling the projector via RS-232C connection
Contents
1. Introduction............................................................................................................. 2
1.1 Connection................................................................................................................................ 2
1.2 Interface.................................................................................................................................... 2
1.2.1 Pin assignment of SERIAL terminal (D-SUB 9-pin)............................................................................... 2
1.2.2 Communications format....................................................................................................................... 2
2.
3.
4.
5.
Control command configuration............................................................................. 3
Control sequence.................................................................................................... 3
Execution procedure of RS-232C commands via LAN........................................... 6
Command list.......................................................................................................... 7
5.1 General control commands....................................................................................................... 7
5.2 Reading commands.................................................................................................................. 7
5.2.1 Status read commands......................................................................................................................... 7
5.2.2 Read commands for items in INFORMATION menu............................................................................. 7
5.2.3 Read commands for other information................................................................................................. 8
5.3
5.4
5.5
5.6
Remote control key commands................................................................................................ 9
Direct commands.................................................................................................................... 10
Function commands............................................................................................................... 10
Menu setting commands........................................................................................................ 11
5.6.1
5.6.2
5.6.3
5.6.4
5.6.5
IMAGE menu....................................................................................................................................... 11
INSTALLATION menu.......................................................................................................................... 11
FEATURE menu................................................................................................................................... 12
SIGNAL menu..................................................................................................................................... 12
NETWORK menu................................................................................................................................ 13
5.7 Password lock commands...................................................................................................... 14
1
1. Introduction
This projector is controllable by a personal computer with RS-232C terminal.
PC-controllable functions:
•
•
•
•
Turning the power ON or OFF
Changing input signals
Inputting commands by pressing the buttons on the control panel and remote control
Menu setting
[Compatibility with the former models]
To use the RS-232C commands designed for the former models of Mitsubishi projector, by inputting
“00COMMAND0”, the projector responds in the same way as the former models. (No NAK is returned. For NAK
response, see page 4.)
(For the recommended procedure to use the former command systems, see “Controlling the projector using a
personal computer” for FL7000U.)
ITEM
Character
COMMAND
Changing the RS-232C
command system
Function
ASCII code
43h 4Fh 4Dh 4Dh 41h 4Eh 44h
Data
0 (Former command system), 1 (New
command system)
1.1 Connection
Important:
• Make sure to connect one computer to one projector.
• Make sure that your computer and projector are turned off before connection.
• Boot up the computer first, and then plug the power cord of the projector.
(If you do not follow this instruction, the COM port may not function.)
• Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.
To RS-232C terminal
RS-232C crossover cable
D-SUB 9-pin
To SERIAL
terminal
D-SUB 9-pin
1.2 Interface
1.2.1 Pin assignment of SERIAL terminal (D-SUB 9-pin)
Pin No.
1
2
3
4
5
6
7
8
9
Name
OPEN
RXD
TXD
OPEN
GND
OPEN
OPEN
OPEN
OPEN
I/O
IN
OUT
1.2.2 Communications format
PROTOCOL
BAUD RATE
DATA LENGTH
PARITY BIT
STOP BIT
FLOW CONTROL
RS-232C
9600 [bps]
8 [bits]
NONE
1 [bit]
NONE
This projector uses RXD, TXD and GND lines for RS-232C control.
For RS-232C cable, the supplied cable (crossover cable) should be used.
2
2.Control command configuration
The command consists of the address code, function code, data code, ACK/NAK, and end code. The length of the
command varies among the functions.
ASCII code
Character
Address code
‘30h’ ‘30h’
00
Function code
Function
Function
Data code
Data
Data
ACK/NAK
‘3Ah’ ‘4Eh’
:N
End code
‘0Dh’
[Address code]
Fixed to 00. (‘30h’ ‘30h’ in the ASCII code)
[Function code] Code unique to each control operation.
[Data code]Data (value) unique to each control operation (Not always indicated.)
[ACK/NAK]Code indicating the NAK return as described below
Fixed to :N (‘3Ah’ ‘4Eh’ in the ASCII code. Not added to ACK.)
[End code]Fixed to . (‘0Dh’ in the ASCII code)
3.Control sequence
Computer
Projector
1
1
2
3
2
Sequence
Send the command from the
personal computer to the projector.
After receiving the end code,
the projector sends the return
command.
4
3
4
The personal computer checks the
return command and confirms if the
sent command has been received or
not.
Use the check command to see
if the projector has executed the
command.
3
Note
If the projector does not receive commands
normally, that is, if the projector is not connected
physically or unable to receive commands, it does
not send out a return command.
When the received command cannot be executed,
NAK is returned (as described below).
This projector sends various codes including
the return code. During the control sequence
by RS-232C, reject other codes on the personal
computer.
• NAK return
In the following cases, the projector returns the command with “:N” added.
(1)Though the command sent from the computer is received by the projector successfully, it cannot be
executed because the projector is in the operation prohibition state.
(2)The data length of the sent command is incorrect or the command is invalid.
(3)The signal length of the command is 48 bytes or longer.
• When a command is sent out during the following operations, it may not be executed.
(1)During signal switching
(2)In the process of the auto position
(3)After the power is turned on.
After the power is turned on, no command is received until the image is displayed. (Usually, it takes about
20 seconds. However, when the lamp illumination takes time, more time will be required accordingly.) In
this case, the projector returns the received command with NAK added.
• The return command is sent out within 1 second. In some cases, the response time takes longer (about 3
seconds).
• When sending commands successively, wait to receive the return command of the current command
before sending a next command.
• The projector may not receive a command when the splash screen is being displayed immediately after
turning on the power. Use command “00r10” to cancel the splash screen.
• While using the LAN terminals, the LAN functions take precedence.
• For the LAN terminals, the same commands as those for connecting with the TCP/IP (port number 63007) are
available. Note, however, that the response becomes slightly slower than when using the RS-232C terminals.
For the use of LAN terminals, refer to “4. Execution procedure of RS-232C commands via LAN”.
• When the NAK isn’t returned, check the RS-232C command system (00COMMAND).
[Example 1] Turning ON the power. (Values enclosed in quotation marks are ASCII codes.):
Command sent from the PC
Status code returned
from the projector
‘30’ ‘30’ ‘21’ ‘0D’
00!
Description
Command for POWER ON
‘30’ ‘30’ ‘21’ ‘0D’
00!
Command receipt confirmation
(Command echo back)
[Example 2] Selecting VIDEO as the input signal during auto positioning (Values enclosed in quotation marks are
ASCII codes.):
Command sent from the PC
Status code returned
from the projector
30’ ‘30’ ‘5F’ ‘76’ ‘31’ ‘0D’
00_v1
‘30’ ‘30’ ‘5F’ ‘76’ ‘31’ ‘3A’ ‘4E’ ‘0D’
00_v1:N
Description
(During auto positioning)
Command for selecting VIDEO as the
input signal is sent out.
The command is received by the
projector but cannot be executed.
(NAK return)
• The flowchart on the next page shows the recommended operating sequence for your reference to create a
program.
4
[RS-232C control flowchart]
START
Sending out command
No NAK returned
No response for
3 seconds or longer
Awaiting response
from projector
NAK returned
Command is sent successfully.
Command is executed successfully.
Checking execution of
command (sending out
check command)
Command is sent successfully.
Command execution fails.
Check the following.
• Check that the function code is
correct.
• Check that the data code is correct.
• Check that the projector is able to
issue the return command.
→ Check the projector’s operation
using the 00vST command.
Note: In the following cases, NAK is
returned even when the
projector is in normal condition.
• Immediately after the power is
turned on
(For status read commands)
approximately for 20 seconds
(For other commands) approximately for 1 minute
• During input switching
• During auto positioning
• During password lock
NG
OK
END
Command sending fails.
Check the following.
• Check that the command begins
with “00”.
• The projector is not supplied with
AC power.
→ Check that AC power cord is
connected.
→ Turn on the power. (Turn on the
circuit breaker.)
• Not connected with the projector.
→ Check that the RS-232C cable is
connected.
→ Check the RS-232C cable for
electrical discontinuity.
[Method of checking state of projector]
Sending “00vST”
To normal operation
0–3
Checking response to “00vST”
6
Enter password.
Send out “00PASS****.”
4
Projector error
Send out “00vER” to check error details.
Recover from error state.
5
Projector is functioning.
Use “00FNCOFF” to cancel the current function.
5
4. Execution procedure of RS-232C commands via LAN
• When you use the LAN function, set the STANDBY MODE to STANDARD or LAN.
• When you execute RS-232C commands via LAN, check that the CONTROL SYSTEM in the NETWORK menu is
set to STANDARD.
• You can change the certification password using the NETWORK PASSWORD in the NETWORK menu. The default
password is “admin.”
• You can skip the certification process by setting the NETWORK CERTIFICATION in the NETWORK menu to OFF.
When you skip the certification process, Steps 2 to 4 described below can be skipped and you can send RS-232C
commands without adding a certification data.
Example:
Sending the PON command (00!) while the NETWORK CERTIFICATION is set to OFF
00!
For the procedure to set the menu, refer to the User Manual supplied with the projector.
To execute the RS-232C command via LAN while the NETWORK CERTIFICATION is set to ON, a 32-byte connection
certification data must be added before the RS-232C command.
To create a 32-byte certification data, following information and procedure are required.
• Random character string for creating the certification data that is acquired from the projector (8 characters)
• Network password of the projector (1 to 32 characters)
• MD5 hash calculation
• Based on the above, the execution procedures to connect to the projector and send the RS-232C commands
while the NETWORK CERTIFICATION is set to ON are described below.
1. Connect to Port 63007 of the projector from the PC as a TCP/IP client.
2. After completing the connection, send the acquisition request for the certification data (“$AK ”) (ASCII
code: 24 41 4B 0D) from the PC to the projector.
3. Acquire “$AK******** ” on the PC as the response of the request sent in Step 2. (********: Random character
string for creating the certification data)
4. Create the certification data on the PC.
• Create the key of the certification data by linking the data acquired in Step 3 with the network character string.
For example, when the random character string is 12345678 and the password is ABCD, the key of the
certification data is 12345678ABCD (character string in ASCII code).
• Run MD5 hash on the key of the certification data.
• Create the certification data by converting the hash-calculated 16-byte data into the ASCII code character string.
Example:
Calculation result: [4f][3c][5d][a1][7b][4f][b5][ed][2c][99][4e][bb][f6][57][67][54] (hexadecimal numeral)
Certification data: 4f 3c 5d a1 7b 4f b5 ed 2c 99 4e bb f6 57 67 54 (character string in ASCII code)
5. Send the RS-232C command with the certification data from the PC to the projector.
Example:
To send the PON command (00! ) using the certification data created in Step 4:
4f3c5da17b4fb5ed2c994ebbf657675400!
6. Receive the response from the projector on the PC.
Response data has the following patterns.
Normal: 00! (Parameter is added depending on the command.)
Error in the certification data: PRV=ERRA
Command error: 00!:N
PC
Projector
1. Connection
2. Acquisition request of the certification data
3. Receiving of the certification data
4. Creation of the certification data
5. Sending of the RS-232C command
6. Receiving of the response data
6
5. Command list
5.1 General control commands
The general control commands are used for the basic operation setting of this projector. They may not be executed while the signals are changed. The general control commands have no data codes. (When the commands
for input select are sent while the splash screen is being displayed, the splash screen is only canceled.)
ITEM
POWER ON
POWER OFF
INPUT COMPUTER 1
INPUT COMPUTER 2
INPUT HDMI
INPUT DVI
INPUT VIDEO
INPUT S-VIDEO
[Example]
Function
Character ASCII code
!
21h
"
22h
_r1
5Fh 72h 31h
_r2
5Fh 72h 32h
_d1
5Fh 64h 31h
_d2
5Fh 64h 32h
_v1
5Fh 76h 31h
_v2
5Fh 76h 32h
Note
This command is invalid for 150 seconds after the power is turned off.
This command is invalid for 1 minute after the power is turned on.
This command is not received during stand-by and BLANK.
This command is not received during stand-by and BLANK.
This command is not received during stand-by and BLANK.
This command is not received during stand-by and BLANK.
This command is not received during stand-by and BLANK.
This command is not received during stand-by and BLANK.
When setting the input signal to COMPUTER 1. (Values enclosed in quotation marks are ASCII
codes.):
Status code returned
from the projector
Command sent from the PC, etc.
Description
‘30’ ‘30’ ‘5F’ ‘72’ ‘31’ ‘0D’
00_r1
Command for setting the input signal
to COMPUTER 1
Command receipt confirmation
(Command echo back)
‘30’ ‘30’ ‘5F’ ‘72’ ‘31’ ‘0D’
00_r1
5.2 Reading commands
5.2.1 Status read commands
The projector’s operating status, such as POWER-ON/OFF and the currently selected input terminal, etc. can be monitored.
ITEM
POWER
Function
Character
vP
INPUT
vI
P-ON/OFF
ENABLED/DISABLED
SIGNAL INPUT
vPK
vSM
Data (Receive)
Character
ASCII
1
31h
0
30h
r1
72h 31h
r2
72h 32h
d1
64h 31h
d2
64h 32h
v1
76h 31h
v2
76h 32h
ASCII
76h 50h
76h 49h
76h 50h 4Bh
76h 53h 4Dh
0
30h
1
31h
0
1
30h
31h
Status
POWER ON
POWER OFF
INPUT COMPUTER 1
INPUT COMPUTER 2
INPUT HDMI
INPUT DVI
INPUT VIDEO
INPUT S-VIDEO
POWER ON/OFF
DISABLED
POWER ON/OFF
ENABLED
NO SIGNAL SUPPLIED
SIGNAL SUPPLIED
5.2.2 Read commands for items in INFORMATION menu
Use the following commands to obtain the values of the items in the INFORMATION menu.
ITEM
LAMP TIME (LOW)
SERIAL NUMBER
RESOLUTION
VERTICAL FREQUENCY
HORIZONTAL FREQUENCY
SYNC. TYPE
Character
vLE
vS/N
vRESO
vVFREQ
vHFREQ
vSYNCT
Function
ASCII code
76h 4Ch 45h
76h 53h 2Fh 4Eh
76h 52h 45h 53h 4Fh
76h 56h 46h 52h 45h 51h
76h 48h 46h 52h 45h 51h
76h 53h 59h 4Eh 43h 54h
Data (Receive)
hhhhmm
******* (within 7 characters)
HHHHxVVVV
***.**
***.**
0 (NO SIGNAL), 1 (Invalid), 3 (3wire),
4 (4wire), 5 (5wire), 6 (SCART)
“hhhh” and “mm” represent hours and minutes respectively.
“HHHH” and “VVVV” represent the horizontal and vertical resolutions respectively.
“***.**” represents the vertical frequency (in Hz) or the horizontal frequency (in kHz).
7
5.2.3 Read commands for other information
Use the following commands to obtain other information.
Model name
Input source
Number of remaining filters
Reading of filter usage time
Projector status
Character
vMDL
vSOUCE
vFLTS
vFLTT
vST
Function
ASCII code
76h 4Dh 44h 4Ch
76h 53h 4Fh 55h 43h 45h
76h 46h 4Ch 54h 53h
76h 46h 4Ch 54h 54h
76h 53h 54h
Error status
vER
76h 45h 52h
ITEM
Data (Receive)
**************** (within 16 characters)
r1 r2 v1 v2 d1 d2
00 to 09
0000 to 9999
0(Stand-by mode),
1(Within 1 minute after POWER-ON (warm-up
mode)),
2(POWER-ON mode (including state of warning)),
3(Cooling mode),
4(Abnormal state (including shutdown due to an
error)),
5(State of functioning (menu display, dialog display,
BLANK, SPLIT, MAGNIFY, FREEZE, etc.)),
6(Awaiting password entry)
Reading of the error status data (3 digits,
hexadecimal numbers, total 9 bits)
(MSB) xb1, xb2... xb8, xb9, 0, 0, 0 (LSB)
xb1(800): Fan error
xb2(400): Lamp error (The lamp goes out or does not
light.)
xb3(200): Lamp warning 1 (The lamp life has
expired.)
xb4(100): Lamp warning 2 (The lamp life is expiring.)
xb5(080): Temperature error
xb6(040): The temperature warning is being
indicated.
xb7(020): Lamp cover open error
xb8(010): Filter/filter cover open error
xb9(008): States of other component abnormality
When only one error occurs, value shown in
parentheses is returned.
When multiple errors occur at the same time, the
bits of all the occurred error are set.
Example)
C00: When fan error and lamp error occur at the
same time
180: When lamp warning 2 and temperature error
occur at the same time
The PC sends the command without attaching the data code to it. On the other hand, the projector attaches to
the received command its current operating status as the data code and send it back to the PC.
[Example]
When checking the currently selected input terminal (when the INPUT VIDEO is being selected).
(Values enclosed in quotation marks are ASCII codes.):
Command sent from the PC, etc.
Status code returned
from the projector
‘30’ ‘30’ ‘76’ ‘49’ ‘0D’
00vl
‘30’ ‘30’ ‘76’ ‘49’ ‘76’ ‘31’ ‘0D’
00vlv1
8
Description
Command for checking the input
terminal
Check result (VIDEO)
5.3 Remote control key commands (Not executable in stand-by mode. When the remote control key commands are sent while the splash screen is being displayed, the splash screen is only canceled.)
The remote control key commands allow the computer to control the projector in the same way as by the remote control.
(Some operations cannot be controlled.) The remote control key commands have no data codes.
Button’s name on remote
control
+/VOLUME
-/VOLUME
ZOOM/FOCUS
LENS SHIFT
GEOMETRY
MAGNIFY
PinP/SPLIT (PinP only)
BLANK
MENU
ENTER
AUTO POSITION
FREEZE
ASPECT
CE
TEST PATTERN
SUPER RESOLUTION
1 (numeric keypad)
2 (numeric keypad)
3 (numeric keypad)
4 (numeric keypad)
5 (numeric keypad)
6 (numeric keypad)
7 (numeric keypad)
8 (numeric keypad)
9 (numeric keypad)
0 (numeric keypad)
[Example]
Character
r06
r07
r0f
r47
r43
r02
r04
ra6
r53
r2b
r4f
r59
r54
r10
r09
ra4
re2
re7
r50
r96
r49
r4a
r4b
r4c
r4d
r4e
r88
r58
r89
r48
Function
ASCII code
72h 30h 36h
72h 30h 37h
72h 30h 66h
72h 34h 37h
72h 34h 33h
72h 30h 32h
72h 30h 34h
72h 61h 36h
72h 35h 33h
72h 32h 62h
72h 34h 66h
72h 35h 39h
72h 35h 34h
72h 31h 30h
72h 30h 39h
72h 61h 34h
72h 65h 32h
72h 65h 37h
72h 35h 30h
72h 39h 36h
72h 34h 39h
72h 34h 61h
72h 34h 62h
72h 34h 63h
72h 34h 64h
72h 34h 65h
72h 38h 38h
72h 35h 38h
72h 38h 39h
72h 34h 38h
When displaying the MENU selection bar. (Values enclosed in quotation marks are ASCII codes.):
Command sent from the PC, etc.
Status code returned
from the projector
‘30’ ‘30’ ‘72’ ‘35’ ‘34’ ‘0D’
00r54
‘30’ ‘30’ ‘72’ ‘35’ ‘34’ ‘0D’
00r54
9
Description
Command operating the same as the
MENU button
Command receipt confirmation
(Command echo back)
5.4 Direct commands (Not executable in stand-by mode. Possible only to read during BLANK.)
The direct commands are used to numerically adjust the geometrical correction and volume.
When the computer sends the command without adding the setting value, the projector returns the received
command with the current setting value added as a data code.
ITEM
Character
KS
KEYSTONE (vertical)
Function
ASCII code
4Bh 53h
Data
±40
With CURVED-adjustment : ±10
±25
With CURVED-adjustment : ±10
KEYSTONE (horizontal)
KSH
4Bh 53h 48H
KEYSTONE reset
CORNERSTONE LOWER RIGHT
(vertical)
CORNERSTONE LOWER RIGHT
(horizontal)
CORNERSTONE LOWER LEFT
(vertical)
CORNERSTONE LOWER LEFT
(horizontal)
CORNERSTONE UPPER RIGHT
(vertical)
CORNERSTONE UPPER RIGHT
(horizontal)
CORNERSTONE UPPER LEFT
(vertical)
CORNERSTONE UPPER LEFT
(horizontal)
CORNERSTONE reset
HORIZ. CURVED ARC
KSRST
CNLRV
4Bh 53h 52h 53h 54h
43h 4Eh 4Ch 52h 56h
±50
CNLRH
43h 4Eh 4Ch 52h 48h
±50
CNLLV
43h 4Eh 4Ch 4Ch 56h
±50
CNLLH
43h 4Eh 4Ch 4Ch 48h
±50
CNURV
43h 4Eh 55h 52h 56h
±50
CNURH
43h 4Eh 55h 52h 48h
±50
CNULV
43h 4Eh 55h 4Ch 56h
±50
CNULH
43h 4Eh 55h 4Ch 48h
±50
CKSRST
CVAH
43h 4Bh 53h 52h 53h 54h
43h 56h 41h 48h
VERT. CURVED ARC
CVAV
43h 56h 41h 56h
HORIZ. CURVED ORIGIN (vertical)
HORIZ. CURVED ORIGIN
(horizontal)
VERT. CURVED ORIGIN (vertical)
VERT. CURVED ORIGIN (horizontal)
CURVED reset
VOLUME
CVHOV
CVHOH
43h 56h 48h 4Fh 56h
43h 56h 48h 4Fh 48h
CVVOV
CVVOH
CVRST
VL
43h
43h
43h
56h
56h 56h 4Fh 56h
56h 56h 4Fh 48h
56h 52h 53h 54h
4Ch
±50
With KEYSTONE-adjustment
: ±15
±50
With KEYSTONE-adjustment
: ±15
±10
±10
±10
±10
00 to 31
How to set the value
Use the character or ASCII code as shown below to set the value.
Character
+
0
1
2
3
4
5
6
7
8
9
ASCII code ‘2Bh’ ‘2Dh’ ‘30h’ ‘31h’ ‘32h’ ‘33h’ ‘34h’ ‘35h’ ‘36h’ ‘37h’ ‘38h’ ‘39h’
5.5 Function commands (Not executable in stand-by mode. When these commands are sent while the splash
screen is being displayed, the splash screen is canceled.)
ITEM
BLANK
PinP
MAGNIFY
FREEZE
Function canceling
Character
MUTE
PiP
MGNFY
FRZ
FNCOFF
Function
ASCII code
4Dh 55h 54h 45h
50h 69h 50h
4Dh 47h 4Eh 46h 59h
46h 52h 5Ah
46h 4Eh 43h 4Fh 46h 46h
10
Data
0 (OFF), 1 (ON)
0 (OFF), 1 (ON)
0 (OFF), 1 (ON)
0 (OFF), 1 (ON)
5.6 Menu setting commands (Not executable in stand-by mode except some commands. Possible only to read
during BLANK except some commands.)
The menu setting commands are used for the menu setting of this projector. If the personal computer sends the
command without attaching the data code, the projector attaches to the received command its current setting
value as the data code and send it back to the PC.
5.6.1 IMAGE menu
ITEM
COLOR ENHANCER
Character
CE
Function
ASCII code
43h 45h
Data
COLOR ENHANCERUSER-GAMMA MODE
SUPER RESOLUTION
SUPER RESOLUTIONLEVEL
CONTRAST
BRIGHTNESS
NCM (MODE)
NCM (R,G,B)
NCM (Y,C,M)
NCM (SATURATION)
NCM (RGB-TINT)
COLOR TEMP.
COLOR TEMP.-USERCONTRAST
COLOR TEMP.-USERBRIGHTNESS
COLOR
TINT
SHARPNESS
AUTO IRIS
NOISE REDUCTION
CTI
INPUT LEVEL
CEU1GS
43h 45h 55h 31h 47h 53h
0 (AUTO), 1 (PRESENTATION), 2 (STANDARD),
3 (THEATER), 4 (sRGB), 5 (USER),
6 (CLEAR BASE), 7 (BLUE BASE)
0 (DYNAMIC), 1 (NATURAL), 2 (DETAIL)
DHD
DHDLV
44h 48h 44h
44h 48h 44h 4Ch 56h
0 (OFF), 1 (ON)
1 to 5
PP
QQ
CMT
MRGB
MYCM
MSAT
MT
A
P
50h
51h
43h
4Dh
4Dh
4Dh
4Dh
41h
50h
±30
±30
1 (VIDEO), 2 (COMPUTER), 3 (USER), 4 (OFF)
±30 ±30 ±30 (R+G+B)
±30 ±30 ±30 (Y+C+M)
±05
±15
1 (STANDARD), 2 (HIGH), 3 (LOW), 4 (USER)
±30 ±30 ±30 (R, G, B)
Q
51h
±30 ±30 ±30 (R, G, B)
T
S
R
IRIS
NR
CTI
IPL
54h
53h
52h
49h
4Eh
43h
49h
CLOSED CAPTION
CC
43h 43h
±10
±10
±05
0 (OFF), 1 (ON)
0 (OFF), 1 (ON)
0 (OFF), 1 (ON)
±5,
For DVI input: +0 (NORMAL), +1 (ENHANCED)
For HDMI input: +0 (AUTO), +1 (NORMAL),
+2 (ENHANCED)
0 (OFF), 1 (CC1), 2 (CC2)
50h
51h
4Dh
52h
59h
53h
54h
54h
47h 42h
43h 4Dh
41h 54h
52h 49h 53h
52h
54h 49h
50h 4Ch
5.6.2 INSTALLATION menu
ITEM
LAMP MODE
STANDBY MODE
AUTO POWER ON
AUTO POWER OFF
Character
LM
STBY
APON
APOF
Function
ASCII code
4Ch 4Dh
53h 54h 42h 59h
41h 50h 4Fh 4Eh
41h 50h 4Fh 46h
SPLASH SCREEN
BACK COLOR
IMAGE REVERSE
SS
BB
IR
53h 53h
42h 42h
49h 52h
ZOOM/FOCUS LOCK
LENS SHIFT LOCK
LENS SHIFT RESET
DVI LONG CABLE
(MODE)
DVI LONG CABLE
(LEVEL)
FZL
LSL
LSRST
DVIC
46h
4Ch
4Ch
44h
DVICLV
44h 56h 49h 43h 4Ch 56h
5Ah
53h
53h
56h
4Ch
4Ch
52h 53h 54h
49h 43h
11
Data
0 (STANDARD), 1 (LOW)
0 (STANDARD), 1 (LOW), 2 (LAN)
0 (OFF), 1 (ON)
0 (OFF), 1 (5 min.), 2 (10 min.), 3 (15 min.),
4 (30 min.), 5 (60 min.), 6 (4 hours), 7 (8 hours)
0 (OFF), 1 (ON)
0 (BLACK), 1 (BLUE), 2 (IMAGE)
0 (OFF), 1 (MIRROR), 2 (INVERT),
3 (MIRROR INVERT)
0 (OFF), 1 (ON)
0 (OFF), 1 (ON)
0 (AUTO), 1 (MANUAL)
00 to 21
5.6.3 FEATURE menu
ITEM
ASPECT
ASPECT-16:9-POSITION
ASPECT-16:9-MODE
PROJECTOR ID
PASSWORD FUNCTION
Character
SC
SCP
SCM
PID
PSLOCK
Function
ASCII code
53h 43h
53h 43h 50h
53h 43h 4Dh
50h 49h 44h
50h 53h 4Ch 4Fh 43h
4Bh
Data
0 (NORMAL), 1 (16:9), 2 (FULL)
0 (CENTER), 1 (UPPER), 2 (LOWER)
0 (ALL SIGNALS), 1 (VIDEO ONLY)
00 (ALL), 01 to 63
0**** (UNLOCK), 1**** (DISPLAY INPUT),
2**** (MENU ACCESS), 3**** (SPLASH ID
SCREEN)
**** is a 4 to 8-digit password comprised of any
figures 1 to 4.
0 (Upper left), 1 (Lower right)
0 (VIDEO), 1 (AUTO), 2 (FILM)
0 (OFF), 1 (Every 500 hours), 2 (Every 750 hours),
3 (Every 1000 hours)
MENU POSITION
CINEMA MODE
FILTER MENU
-AUTO ROLL UP
PERIOD
FILTER MENU
-MANUAL ROLL UP
FILTER MENU
-REMAINING FILTERS
FILTER MENU
-FILTER USAGE TIME
FILTER MENU
-FILTER RESET
LANGUAGE
MP
CINE
FLCP
4Dh 50h
43h 49h 4Eh 45h
46h 4Ch 43h 50h
FLMC
46h 4Ch 4Dh 43h
vFLTS
46h 4Ch 54h 53h
00 to 09 (number of times)
vFLTT
46h 4Ch 54h 54h
0000 to 9999 (hours)
TRSTFL
54h 52h 53h 54h 46h 4Ch
LG
4Ch 47h
HIGH ALTITUDE MODE
VIDEO SIGNAL
(VIDEO only)
SET UP
SCART INPUT
LAMP WARNING
HIDE OSD
RESET ALL
ALTI
VS
41h 4Ch 54h 49h
56h 53h
STU
SRT
LW
HOSD
RSTALL
53h
53h
4Ch
48h
52h
Reset of the number of remaining filters and filter
usage time
00 (
), 01 (English), 02 (Español),
03 (Deutsch), 04 (Français), 05 (Italiano), 06 (
),
07 (
), 08 (
), 09 (PORTUGUÊS),
11 (SVENSKA), 12 (POLSKI), 16 (Nederlands),
17 (Norsk), 18 (
), 19 (Türkçe),
20 ( ภาษาไทย ), 21 (Bahasa Indonesia), 22 (Melayu),
23 (
)
0 (STANDARD), 1 (HIGH ALTITUDE)
0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM),
4 (4.43NTSC), 5 (PAL-M), 6 (PAL-N), 7 (PAL-60)
0 (AUTO), 1 (OFF), 2 (3.75%), 3 (7.5%)
0 (OFF), 1 (ON)
0 (STANDARD), 1 (SHORT TERM)
0 (OFF), 1 (ON)
54h
52h
57h
4Fh
53h
55h
54h
53h 44h
54h 41h 4Ch 4Ch
5.6.4 SIGNAL menu
ITEM
MEMORY CALL
HORIZ.POSITION
VERT. POSITION
FINE SYNC.
TRACKING
COMPUTER INPUT
OVER SCAN
HOLD
HOLD BEGIN
HOLD END
CLAMP POSITION
CLAMP WIDTH
VERT. SYNC.
LPF
SHUTTER(U)
SHUTTER(L)
SHUTTER(LS)
SHUTTER(RS)
Character
MMC
HP
VP
FN
TRK
CIN
VOS
HLD
HLB
HLE
CLP
CLW
VSC
LPF
SHU
SHL
SHLS
SHRS
Function
ASCII code
4Dh 4Dh 43h
48h 50h
56h 50h
46h 4Eh
54h 52h 4Bh
43h 49h 4Eh
56h 4Fh 53h
48h 4Ch 44h
48h 4Ch 42h
48h 4Ch 45h
43h 4Ch 50h
43h 4Ch 57h
56h 53h 43h
4Ch 50h 46h
53h 48h 55h
53h 48h 4Ch
53h 48h 4Ch 53h
53h 48h 52h 53h
*1)Setting range differs depending on the input signals.
12
Data
0 (AUTO), 1 (MEMORY1), 2 (MEMORY2)
+ (increment), - (decrement)*1
+ (increment), - (decrement)*1
00 to 31
+ (increment), - (decrement)*1
0 (RGB), 1 (YCBCR/YPBPR), 2 (AUTO)
00 (90%) to 10 (100%)
0 (OFF), 1 (ON)
00–99
00–99
001–255
01–63
0 (AUTO), 1 (OFF)
0 (OFF), 1 (ON)
00 to 38
00 to 38
00 to 63
00 to 63
5.6.5 NETWORK menu
ITEM
PROJECTOR NAME
NETWORK RESTART
Character
NAME
NRCN
Function
ASCII code
4Eh 41h 4Dh 45h
4Eh 52h 43h 4Eh
Data
Up to 15 single-byte alphanumeric characters
• Some commands are not executed depending on the input signal. The operational restrictions same as those
on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.
How to set the value
Use the character or ASCII code as shown below to set the value.
Character
+
0
1
2
3
4
5
6
7
8
9
ASCII code ‘2Bh’ ‘2Dh’ ‘30h’ ‘31h’ ‘32h’ ‘33h’ ‘34h’ ‘35h’ ‘36h’ ‘37h’ ‘38h’ ‘39h’
[Example 1] When setting the AUTO POWER ON to ON. (Values enclosed in quotation marks are ASCII codes.):
Command sent from the PC, etc.
Status code returned
from the projector
‘30’ ‘30’ ‘41’ ‘50’ ‘4F’ ‘4E’ ‘31’ ‘0D’
00APON1
‘30’ ‘30’ ‘41’ ‘50’ ‘4F’ ‘4E’ ‘31’ ‘0D’
00APON1
Description
Command for setting the AUTO
POWER ON to ON
Command receipt confirmation
(Command echo back)
[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and the
CONTRAST B to -5. (Values enclosed in quotation marks are ASCII codes.):
Command sent from the PC, etc.
Status code returned
from the projector
‘30’ ‘30’ ‘50’ ‘2B’ ‘31’ ‘30’ ‘2B’ ‘30’ ‘30’ ‘2D’ ‘30’ ‘35’ ‘0D’
00P+10+00-05
‘30’ ‘30’ ‘50’ ‘2B’ ‘31’ ‘30’ ‘2B’ ‘30’ ‘30’ ‘2D’ ‘30’ ‘35’ ‘0D’
00P+10+00-05
Description
Command for setting the
picture control
Command receipt confirmation
(Command echo back)
[Example 3] When checking the TINT setting (when the TINT is set to +10). (Values enclosed in quotation marks
are ASCII codes.):
Command sent from the PC, etc.
Status code returned
from the projector
‘30’ ‘30’ ‘53’ ‘0D’
00S
‘30’ ‘30’ ‘53’ ‘2B’ ‘31’ ‘30’ ‘0D’
00S+10
Description
Command for checking the
TINT setting
Check result (+10)
[Example 4] When setting the GAMMA MODE of the COLOR ENHANCER-USER to DETAIL. (Values enclosed in
quotation marks are ASCII codes.):
Command sent from the PC, etc.
Status code returned
from the projector
‘30’ ‘30’ ‘43’ ‘45’ ‘55’ ‘31’ ‘47’ ‘53’ ‘32’ ‘0D’
00CEU1GS2
‘30’ ‘30’ ‘43’ ‘45’ ‘55’ ‘31’ ‘47’ ‘53’ ‘32’ ‘0D’
00CEU1GS2
13
Description
Command for setting the
picture control
Command receipt confirmation
(Command echo back)
5.7 Password lock commands
The password lock commands control the password lock. The password lock enabling or disabling command is
sent with a 4 to 8-digit password comprised of any figures 1 to 4 added to the end of the data code. When the
password lock is enabled or disabled successfully, the projector sends a return command comprising the data
code, password, and “1” at the end. When enabling or disabling the password lock fails, it sends a return command with “0” at the end. There is no reconfirmation of the password. The password input command is for enabling projection of image when password lock has been set to DISPLAY INPUT. The password input command
is sent with a 4 to 8-digit password comprised of any figures 1 to 4 at the end.
ITEM
Password lock enabling/
disabling
Password input
Character
PSLOCK
PASS
Function
ASCII code
50h 53h 4Ch 4Fh 43h 4Bh
50h 41h 53h 53h
Data
0**** (Disabling), 1**** (DISPLAY INPUT),
2**** (MENU ACCESS), 3**** (SPLASH ID SCREEN)
****
**** is a 4 to 8-digit password comprised of any figures 1 to 4.
[Example]
When enabling the password lock of DISPLAY INPUT (in the case that the password is 123412).
(Values enclosed in quotation marks are ASCII codes.):
Command sent from the PC, etc.
Status code returned
from the projector
‘30’ ‘30’ ‘50’ ‘53’ ‘4C’ ‘4F’ ‘43’ ‘4B’ ‘31’ ‘31’ ‘32’ ‘33’ ‘34’ ‘31’ ‘32’ ‘0D’
00PSLOCK1123412
‘30’ ‘30’ ‘50’ ‘53’ ‘4C’ ‘4F’ ‘43’ ‘4B’ ‘31’ ‘31’ ‘32’ ‘33’ ‘34’ ‘31’ ‘32’ ‘31’ ‘0D’
00PSLOCK11234121
14
Description
Command for enabling the
password lock of DISPLAY INPUT
Response informing that the
projector succeeded in enabling the
password lock of DISPLAY INPUT