Samsung SDZ-370 User`s manual

High Resolution 37X Zoom Color Camera SDZ-370 User’s Manual
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
ENGLISH
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before operating the camera, confirm the camera model and proper input
power voltage. In order to that you can understand this manual thoroughly,
we'll introduce our model description.
nSDZ-370 SERIES
• NTSC MODEL SDZ-370N • PAL MODEL
SDZ-370P
n MODEL DESCRIPTION
• SDZ-370X_
SIGNAL SYSTEM
• SIGNAL SYSTEM
N → NTSC MODEL
P → PAL MODEL
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
INFORMATION -This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
WARNING - To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than that specified.
◆ Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
Features
Contents
• Features…………………………………………………………… 5
• Warnings & Cautions… ………………………………………… 6
• Components and Accessories… ……………………………… 8
• Overview…………………………………………………………… 9
• Connection………………………………………………………… 11
■ Connecting to Monitor… ……………………………………………… 11
■ Connecting to Power………………………………………………… 12
■ Connecting to 8P Control Terminal……………………………………… 12
• Operating Your Camera… ……………………………………… 14
■ Menu Configuration… ………………………………………………… 14
■ Menu Setup…………………………………………………………… 14
- WHITE BALANCE… ………………………………………………………
- BACK LIGHT………………………………………………………………
- MOTION DETECTION………………………………………………………
- FOCUS……………………………………………………………………
- EXPOSURE… ……………………………………………………………
- SPECIAL… ………………………………………………………………
- RESET……………………………………………………………………
- EXIT………………………………………………………………………
15
16
19
20
25
29
37
37
• Troubleshooting…………………………………………………… 37
• Specifications… ………………………………………………… 39
• STW Protocol Command Description… ……………………… 40
37x Optical Zoom
Day & Night
The built-in SDZ-370 optical zoom lens is a
highly durable component. It features auto
focus, auto iris, and zoom functions.
The camera automatically determines whether
it is night time or day time, selecting operating
mode automatically. The camera operates in
color mode during day light conditions and BW
mode in night conditions for clearer identification.
SSNR (Samsung Super Noise
Reduction)
DIS(Digital Image Stabilizer)
The high performance W-IV DSP chip
dramatically reduces the gain noise in digital
image precessing, producing clear, sharp
images in low lighting environments.
The DIS function can compensate for vibration of
the camera. so it helps you obtain more
stabilized image under the shaking conditions.
Motion Detection
Fine Picture Quality under Ultra Low
Lighting
Once motion is detected, the camera sends an
alert signal to the processing unit, which, if
used in conjunction with an optional alarm, can
provide effective surveillance of your property.
1/4" high density CCD allows the user to
capture bright, high-quality images under ultra
low lighting conditions.
High Resolution
Miscellaneous Functions
Featuring 550TV line horizontal resolution in
color mode and 680TV line horizontal resolution in
BW mode, the camera features Sony's 410,000
pixel CCD and captures clean, noiseless, highquality images.
SENS-UP, FLIP(H/V-REV), D-ZOOM, SHARPNESS,
MOTION DETECTION and PRIVACY functions
are provided.
Control via OSD Menu and RS-485
The OSD menu and RS-485 pins allow for
remote control of the camera.
The user can also directly control the lens
using external control connection.
COLOR CCD CAMERA
4
User’s Manual
COLOR CCD CAMERA
5
User’s Manual
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to provide
customers with more environment-friendly products.The Eco mark represents
Samsung Techwin's will to create environment-friendly products, and indicates
that the product satisfies the EU RoHS Directive.
Precautions
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
Warnings & Cautions
This information is provided to ensure your safety and to prevent any losses, financial or
otherwise. Please read it carefully and use the product accordingly.
* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as
an aerial ladder while providing after-sales service shall be at your expense.
* Separate the power plug when thunder crashes or lighting flashes.
* This product is support equipment for surveillance system. Therefore, we can't compensate for material loss and/or
personal injuries by robbery, fire, natural disaster or something like this type.
Warning/Attention/Special Mark Messages
Ignoring this information may
result in material loss and/or
serious personal injuries including
death.
Ignoring this information may
result in material loss and/or a
slight injuries.
Indicates “Never Allowed.”
Indicates “No Disassembling.”
Use only under temperature conditions between
-10ºC and +50ºC. Provide good ventilation when
using in high temperature conditions.
May lower image quality.
Do not install under unstable
lighting conditions.
Severe lighting changes or flickering may hinder
normal camera operation.
Avoid touching the camera lens.
The lens is the most important component of
the camera. Be careful not to smear it with
fingerprints.
Do not drop the camera or subject
it to physical shock.
May cause a product malfunction.
COLOR CCD CAMERA
6
User’s Manual
COLOR CCD CAMERA
Never keep the camera face to
strong light directly.
May damage the CCD.
7
User’s Manual
Precautions
Overview
Do not expose the camera to rain
or other types of liquids.
Do not expose the camera to
radioactivity.
Top
Bottom
2
1
May cause a product malfunction.Wipe dry any
liquids. Liquids may contain minerals that are
corrosive to electronic components.
Radioactivity exposure may damage the CCD.
Notes
• Exposure to a spotlight or an object emitting strong light may cause smear or blooming.
• Ensure that the power source complies with normal specifications before supplying it to
the camera.
1 Tripod Mounting Bracket Screw Hole
Used to fix tripod mounting bracket on top of
the camera.
2 Tripod Mounting Hole
Used to install the camera on an optional tripod.
The tripod must be equipped with screws with
specifications shown on the right.
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
Components and Accessories
1
2
3
Attach the bracket to the top of the camera. Use screws included in
the package or their equivalent (less than 6mm). Otherwise, the
bracket may not assemble to the camera properly.
1 37x Zoom Color Camera SDZ-370
2 Instruction Manual
3 8-PIN CABLE ASSY
COLOR CCD CAMERA
8
User’s Manual
COLOR CCD CAMERA
9
User’s Manual
Connection
Overview
Connecting to Monitor
Bottom View
Connect Video Out Jack to the monitor's Video In jack as shown below.
5
3
6
4
CCD Camera
Monitor
7
3 Key Buttons
Following buttons control zoom, focus, and auto focus functions.
WIDE button : To widen the view. (ZOOM OUT)
TELE button : To close in on a far object. (ZOOM IN)
F-NEAR button : To see a near object clearly.
F-FAR button : To see a far object clearly.
Pressing the 'SET' button locks the zoom control function of these buttons and
prompts the main setup menu.
Main setup menu can be navigated using these buttons.
SET : To access the main setup menu.
UP (TELE button)
: To move the arrow indicator to up.
DOWN (WIDE button): To move the arrow indicator to down.
LEFT (F-NEAR button) : To move the arrow indicator to left.
RIGHT (F-FAR button) : To move the arrow indicator to right.
4 Power Input Terminal
Power supply terminal (DC12V±10%).
5 Power LED
Illuminates when power is supplied.
6 Video Output Jack
Used to connect an external video monitor in jack.
7 RJ-45 JACK
Terminals, such as RS-485 communications, MD OUT, ZOOM, and FOCUS, EX_DN
are areincluded.
COLOR CCD CAMERA
10 User’s Manual
• Connection methods may vary depending on the video equipment. Please refer to
the model specific instruction manual.
• Connect cables with the unit powered down.
• S et the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.
CCD Camera
Intermediate
COLOR CCD CAMERA
11 User’s Manual
End monitor
Connection
Connecting to Power
Connector Function
DC Power Type (DC 12V, 500mA)
Signal Level
+6V ~ +12V
COM
Wide
COM
- 6V ~ -12V
Far
+6V ~ +12V
COM
Near
COM
- 6V ~ -12V
ZOOM
Use DC 12V/500mA power source for SDZ-370N/P.
Power Input Terminal
FOCUS
Notes
COM
• Connect the power once the installation is complete.
• The wire is polarized. Match '+' and '-' terminals properly.
MD
Connecting to 8P Control Terminal
The camera can be controlled by using external controllers like a Remote controller.
(RS-485 Communication)
I/O
Tele
EX DN
0V
There is no motion
5±0.5sec
← →
I
I
COM
-
+3.0V
There is motion
O
DAY mode: D&N terminals must be OPEN to external signals.
(Do not input voltage)
NIGHT mode: D&N terminal must be connected to the ground
I
Notes
• MD(Motion Detection) Output Signal Level(less than 10mA)
• When using the MD function, the 'GND' should be connected to the frame ground.
• Do not simultaneously connect the RS-485 (+) (-) communication line when you use
voltage control ZOOM and FOCUS, using the RECEIVER BOX (SRX-100B).
SCC-3100A
8-Pin CABLE ASSY
SCC-101
* 8P Control Terminal Configuration
Number
1
2
3
4
Name Cable color Description Number Name Cable color
Description
ZOOM
ORANGE
5
GND
BLUE
FOCUS WHITE/ORANGE
6
EX DN WHITE/BLUE
External D/N
COM
GREEN
7
485+
BROWN
RS-485 communication
MD OUT WHITE/GREEN
8
485- WHITE/BROWN RS-485 communication
COLOR CCD CAMERA
12 User’s Manual
* Match the communication setup between devices when you use the wired controller
(SCC-101) or SCC-3100A.
ITEM
SCC-101(fixed) SCC-3100A(Factory Default)
MODE
Serial
Serial
Data Bit
8 bit
8 bit
Bit/Sec
9600bps
9600bps
Parity
EVEN
NONE
CAM ID NO.
0
1~255
RETURN PACKET
ENABLE
See the SCC-3100A manual
COLOR CCD CAMERA
13 User’s Manual
Notes
• Contact an authorized
technician for
inspection.
Operating Your Camera
Menu Configuration
Main Setup Menu
WHITE BAL
BACKLIGHT
MOTION DET
FOCUS
EXPOSURE
SPECIAL
• ATW
• OUTDOOR
• OFF
• OFF
• MODE
• D-ZOOM
• MANUAL • AWC->SET
• INDOOR
• BLC
• HLC
• ON
• ZOOM TRK
• ZOOM SPEED
• ZOOM POS INIT • USER PRESET
• LENS INIT
• BRIGHTNESS
• AGC
• END
• PRIVACY
• COMM ADJ
• END
• END
• IRIS
• SSNR
• SHUTTER
• SENS-UP
• DAY/NIGHT
• IMAGE ADJ
• DIS
• DISPLAY
RESET
EXIT
Select feature using the UP or
DOWN button.
MAIN SETUP
WHITE BAL
ATW
BACKLIGHT
OFF
MOTION DET
OFF
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
Change the status using the
LEFT or RIGHT button.
2. Select the desired feature using the UP or DOWN button.
• Each pressing of the UP or DOWN button moves the indicator to the next or
previous feature.
• Move the arrow indicator to the desired feature item.
3. C
hange the status of the selected feature using the LEFT or RIGHT button.
4. When completed, move the arrow indicator to 'EXIT' and press the SET button.
Notes
Menu Setup
Use the five buttons on back of the camera.
• Features marked with a have an accessible submenu.
• Access the submenu by pressing the SET button.
UP button
SET/AF button
White Balance (White Bal.)
LEFT button
DOWN button
RIGHT button
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select ’White Bal.‘ by using the Up
and Down buttons so that the arrow indicates ’White Bal.‘ .
2. Select a desired mode using the Up and Down buttons.
1. Press the SET button for 2 seconds. (Short-pressing the button activates
the AUTO FOCUS).
• Main setup menu is displayed on the monitor screen.
COLOR CCD CAMERA
14 User’s Manual
MAIN SETUP
WHITE BAL
ATW
BACKLIGHT
OFF
COLOR CCD CAMERA
15 User’s Manual
Operating Your Camera
✽ Select one of the following 5 modes, as appropriate for your purpose.
A
TW : Select this when the color temperature is between 1800ºK and
10500ºK
INDOOR : Select this when the color temperature is between 4500ºK and 8500ºK.
O
UTDOOR : Select this when the color temperature is between 1800ºK and
10500ºK. (sodium light inclusion)
A
WC →SET : To find the optimal setting for the current luminance environment in this
mode, set the point the camera towards a sheet of white paper and press the
SET button. If the environment changes, readjust it.
M
ANUAL : Select this to fine-tune White Balance manually. Set White Balance first by
using the ATW or AWC mode. After that switch to MANUAL mode, finetune the White Balance and then press the SET button.
BACKLIGHT
This camera is designed so that it delivers a distinctive subject and background at
The same time, even when the subject is in backlight, unlike conventional cameras,
By adopting a proprietary W-IV DSP chip.
1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Up
and Down buttons so that the arrow indicates ‘BACKLIGHT’.
MAIN SETUP
WHITE BAL
ATW
BACKLIGHT
OFF
MOTION DET
OFF
WHITE BAL MANUAL SETUP
RED
BLUE
▶END
117
93
||||||||||||||||||||||||||
||||||||||||||||||||||||||
Press SET to Return
2. S elect a desired mode using the Left and Right buttons depending on the camera pupose.
B
LC : Enables a user to directly select a desired area from a picture, and to view the
area more clearly.
H
LC(High Light Compensation) : If there is a high light installed in dark environment
such as an apartment parking garage or gas
station entrance, removing the high light makes
it possible to view car license plates efficiently.
HLC MASKING AREA
Notes
• White Balance may not work properly under the following conditions. In this case select
the AWC mode.
1When the color temperature of environment surrounding the subject is out of the control
range
2When the ambient illumination of the subject is dim.
3If the camera is directed towards a fluorescent light or is installed in a place where
illumination changes dramatically, the White Balance operation may become unstable.
COLOR CCD CAMERA
16 User’s Manual
HLC ON
COLOR CCD CAMERA
HLC OFF
17 User’s Manual
Operating Your Camera
O
FF : Deactivates the BACKLIGHT function.
3. Select a desired mode using the Left and Right
button and press the SET button.
• S elect ‘BLC’ to adjust the area to be enhanced and
enhancement level.
• S elect ‘HLC’ to adjust the HLC MASK COLOR and
LEVEL.
Motion Detection
BLC SETUP
▶LEVEL
TOP
BOTTOM
LEFT
RIGHT
END
LOW
30 |
70
30 |
70
||||| ||||||||||||||||||||
||||||||||||||||||||||||||
||||| ||||||||||||||||||||
||||||||||||||||||||||||||
HLC SETUP
▶LEVEL
LOW
MASK COLOR
5
END
||||||||||||||||||||||||||
This product has a feature that allows you to observe movements of objects in 4
different areas on the screen, and the words ‘MOTION DETECTED’ appear on the
screen when movement is detected; hence a single individual can conduct
supervision efficiently. The camera detects an object’s movement by sensing
disparity of outline, and level of brightness and color. The camera receives detection
signal from MD output terminal.
MD SETUP
▶AREA SEL
AREA MODE
SENSITIVITY
SMART ZOOM
END
AREA SETUP
AREA1
ON
LOW
ON
▶TOP
BOTTOM
LEFT
RIGHT
END
3
6
3
6
||||||||||||||||||||||||||
||||||||||||||||||||||||||
||||||||||||||||||||||||||
||||||||||||||||||||||||||
• Please press the SETUP button.
- OFF: MOTION DETECTION mode is cancelled.
- ON: Any motion in the selected areas is observed.
Notes
• You cannot use the BLC mode when MANUAL or A.FLK mode in ‘SHUTTER’ menu is
selected.
• Since the following symptoms may occur according to the ambient illumination when BLC
is selected, set it to OFF.
1 Color or screen changes unnaturally.
2 Noise appears in the bright part of the screen.
• Since the performance of the BLC function may be affected by the area of the bright part
of the screen, optimize the installation angle for the best BLC performance.
• If you increase LIMIT, the screen display may be distorted.
• For high performance of BLC function, We recommend that you set IRIS to AUTO in the
EXPOSURE setup.
• Activating BLC may cause the camera to repeat the Auto Focus operation depending on
lighting conditions. It is recommended that you use the Focus Setup menu in One-Push or
Manual mode.
• Smart Zoom and BLC cannot be used in conjunction with each other:
• Setting up BLC and then Smart Zoom automatically cancels BLC.
• Setting up Smart Zoom and then BLC automatically cancels Smart Zoom.
COLOR CCD CAMERA
18 User’s Manual
A
REA SEL : You can select the area you wish to observe from the 8 area.
A
REA MODE : Determines whether to use the MD area selected in SENSITIVITY
SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is
high, motion detection sensitivity is increased to recognize even
small movement
SMART ZOOM SETUP
▶START ZOOM
TARGET ZOOM
DWELL TIME
END
X1
X5
5 SEC
S MART ZOOM : Smart zoom is operated in connection with MOTION DETECTION.
When the SMART ZOOM function is ‘ON’ while the MOTION
DETECTION mode is ‘ON’, the zoom goes to the TARGET ZOOM
position once motion is detected. Once the zoom action is finished
and ‘DWELL TIME’ has passed, the zoom returns to the ‘START
COLOR CCD CAMERA
19 User’s Manual
Operating Your Camera
ZOOM’ position.
• START ZOOM : Use the left or right button in the ‘START ZOOM’ item to select the zoom position
from 1x to 37x to be returned after the ‘SMART ZOOM’ action is over.
• TARGET ZOOM : Use the left or right button in the ‘TARGET ZOOM’ item to select the zoom
position from 1x to 37x to be used during MOTION DETECTION.
• DWELL TIME : U
se the left or right button in the ‘DWELL TIME’ item to select a time between
5 and 60 seconds for the dwell time before the zoom is returned to the ‘START
ZOOM’ position. (5,7,10,15,20,30,40,60 sec)
1. Press the SET button to access the main setup manu and then position the
indicator over FOCUS using the UP or DOWN button.
2. Press the SET button.
MODE
: You can select the most suitable zoom mode. Move the arrow indicator to
’MODE‘ using UP or DOWN button.
T OP, BOTTOM, LEFT,RIGHT : You can adjust the size of the area
Notes
Tips on Using the Motion Detection Feature
• The feature may not function properly under flickering light conditions.
• The camera interprets sudden changes in lighting and subsequent change in brightness of
an object as motion.
• With the feature enabled, other algorithms may require additional time to operate than
usual.
Notes
• This system does not guarantee prevention of fire or theft. The
manufacturer shall not be held responsible for any accident or
damage incurred.
• Connect an external alarm device to MD Out on back of the
camera.
FOCUS
MAIN SETUP
WHITE BAL
ATW
BACKLIGHT
OFF
MOTION DET
OFF
FOCUS
EXPOSURE
COLOR CCD CAMERA
20 User’s Manual
FOCUS SETUP
MODE
ONE-PUSH
ZOOM TRK
AUTO TRACK
ZOOM SPEED
FAST
D-ZOOM
OFF
ZOOM POS INIT AUTO
USER PRESET
OFF
LENS INIT
MANUAL
END
• AUTO
: Select AUTO and press the SET button to
confirm. Increase or decrease optical zoom
ZOOM POS SETUP
(ZOOM) or digital zoom (D-ZOOM)
positions using the UP or DOWN button
while verifying the changes on screen.
Enabling D-ZOOM (ON) means that digital
↑ : TELE ↓ : WIDE
zoom will activate once optical zoom
ends. Focus is automatically adjusted with
moving zoom.
• ONE PUSH : Focus is automatically adjusted just once,
ZOOM/FOCUS POS SETUP
after zoom position is changed. Select
'ONE PUSH' and press the SET button to
confirm. Increase or decrease optical zoom
↑ : TELE ↓ : WIDE
(ZOOM) or digital zoom (D-ZOOM)
← : NEAR → : FAR
positions using the directional buttons
while verifying the changes on screen.
Press the SET button once desired image quality is obtained.
COLOR CCD CAMERA
21 User’s Manual
Operating Your Camera
• MANUAL : Select 'MANUAL' and press the SET button
ZOOM/FOCUS POS SETUP
to confirm. Increase or decrease optical
zoom (ZOOM) or digital zoom (D-ZOOM)
positions using the directi onal buttons
while verifying the changes on screen. Press
↑ : TELE ↓ : WIDE
← : NEAR → : FAR
the SET button on ce desired image quality
is obtained. Focus can be manually
adjusted, independent of moving zoom.
ZOOM TRK : Select ‘ON’ for the ‘SMART ZOOM’ item in the MOTION DETECTION menu
and press SET button to change the settings for the ‘SMART ZOOM’ function.
Use the left or right button in the ‘ZOOM’ item to select ‘AUTOTRACK’ or ‘TRACK’ and press
SET button to activate the zoom action focus function.
• AUTOTRACK: Zooming in while deciding or adjusting the status of the focus.
• TRACK: Zooming in with no relevance to the focus.
• OFF: Only the zoom lens moves.
D-ZOOM : Configure magnification limit from x2~x12 using this feature. Position the
indicator over 'D-ZOOM' using the UP or DOWN button. Set 'D-ZOOM' to
'ON' and press the SET button to confirm.
FOCUS SETUP
MODE
ONE-PUSH
ZOOM TRK
AUTO TRACK
ZOOM SPEED
FAST
D-ZOOM
OFF
ZOOM POS INIT AUTO
- Set 'ZOOM LIMIT' to the desired level using the
LEFT or RIGHT button.
FOCUS SETUP
MODE
ONE-PUSH
ZOOM TRK
AUTO TRACK
Z OOM SPEED : Configure zoom tracing speed using this feature. Position the indicator
over 'ZOOM SPEED' using the UP or DOWN button and then set to
desired mode using the LEFT or RIGHT button.
D-ZOOM LIMIT SETUP
▶LIMIT
END
X2
Notes
• When the DIS is enabled, you cannot use the D-ZOOM.
FOCUS SETUP
MODE
ONE-PUSH
ZOOM TRK
AUTO TRACK
ZOOM SPEED
FAST
• FAST : To move zoom fast.
• MEDIUM : To move zoom at medium speed.
• SLOW : To move zoom slowly.
Notes
• The 'ZOOM SPEED' mode cannot be used if 'MODE' is set to 'AUTO' and 'ZOOM TRK' is
'ON'.
COLOR CCD CAMERA
22 User’s Manual
ZOOM POS INIT: Moves to the controlled ZOOM position when the power truned
on and is a function of the initial ZOOM position control.
FOCUS SETUP
MODE
ONE-PUSH
ZOOM TRK
AUTO TRACK
ZOOM SPEED
FAST
D-ZOOM
OFF
ZOOM POS INIT AUTO
USER PRESET
OFF
COLOR CCD CAMERA
23 User’s Manual
Operating Your Camera
- AUTO :If you turn the power off and on, the zoom magnification level is set to the
previous level that was set before the power went off.
- MANUAL : The zoom magnification level can be set from 1x to 37x.
LENS INIT : Use the left or right button in the ‘Lens
initialization’ item to select
‘Automatic’ or ‘Manual’ and press the
SET button to set up the initialization
of the lens.
Notes
USER PRESET SETUP
PRESET NO 1
PRESET SAVE
▶ PRESET CLEAR
END
||||||||||||||||||||||||||
PRESET NOT DEFINED
• The zoom postion is saved after 5 seconds when you set zoom function.
USER PRESET
• Preset user-designated configurations using this feature. Position the indicator over
‘USER PRESET’ using the UP or DOWN button and then set to ‘ON’ using the LEFT
or RIGHT button. Press the SET button to confirm.
FOCUS SETUP
MODE
ONE-PUSH
ZOOM TRK
AUTO TRACK
ZOOM SPEED
FAST
D-ZOOM
OFF
ZOOM POS INIT AUTO
USER PRESET
OFF
LENS INIT
MANUAL
END
ZOOM/FOCUS POS SETUP
↑ : TELE ↓ : WIDE
← : NEAR → : FAR
USER PRESET SETUP
- PRESET NO : Up to 128 preset configuratons are
supported.
- PRESET SAVE : Save configured preset.
- PRESET CLEAR : Clear configured preset.
- END : Revert to the FOCUS SETUP menu.
▶ PRESET NO 1 ||||||||||||||||||||||||||
PRESET SAVE
PRESET CLEAR
END
• AUTO : The lens is initialized by setting the date. reset time can be set from 1 day to
7 days and the lens resets every 24 hours from the set time.
• Manual : The Lens will reset when you press the SET button.
FOCUS SETUP
MODE
ONE-PUSH
ZOOM TRK
AUTO TRACK
ZOOM SPEED
FAST
D-ZOOM
OFF
ZOOM POS INIT AUTO
USER PRESET
OFF
LENS INIT
MANUAL
END
END : To revert to the main setup menu.
EXPOSURE
PRESET NOT DEFINED
COLOR CCD CAMERA
24 User’s Manual
USER PRESET SETUP
PRESET NO 1
▶ PRESET SAVE
PRESET CLEAR
END
||||||||||||||||||||||||||
PRESET NOT DEFINED
LENS INIT SETUP
DAY
1
END
MAIN SETUP
WHITE BAL
ATW
BACKLIGHT
OFF
MOTION DET
OFF
FOCUS
EXPOSURE
SPECIAL
COLOR CCD CAMERA
25 User’s Manual
Operating Your Camera
1. Press the SET button to access the main setup menu and then position the
indicator over 'EXPOSURE' using the UP or DOWN button.
2. Press the SET button to confirm.
SHUTTER : C
ontrol image brightness by adjusting shutter speed.
1 Position the indicator over 'SHUTTER' using the UP or DOWN button. Then select
the desired shutter mode (A.FLK, ESC, MANUAL) using the LEFT or RIGHT button.
B
RIGHTNESS:
Use this feature to adjust image brightness. Position the indicator over
'BRIGHTNESS' using the UP or DOWN button. Then increase or decrease brightness
level using the LEFT or RIGHT button while verifying the changes on screen. Set
END once desired level is obtained.
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
AGC
EXPOSURE SETUP
BRIGHTNESS
IRIS
|
50
AUTO
|||||||||||| |||||||||||||
|||||||||||| |||||||||||||
• A.FLK (NTSC: 1/100, PAL: 1/120): Flicker-free mode
• ESC
: Automatic shutter speed setting (optimal).
Auto operation is possible only when the IRIS is set to MANUAL.
• MANUAL: Manual shutter speed setting
IRIS: Set'IRIS' to 'AUTO' or 'MANUAL'. Position the indicator over 'IRIS' using the UP
or DOWN button and then select the desired iris mode using the LEFT or RIGHT
button.
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
|
50
AUTO
ESC
MEDIUM
|
50
AUTO
ESC
|||||||||||| |||||||||||||
• AUTO: The iris is automatically activated upon illumination.
• MANUAL: Manual iris configuration. Set 'IRIS' to 'MANUAL' using the LEFT or RIGHT
button and then press the SET button. Increase or decrease iris level using
the LEFT or RIGHT button while verifying the changes on screen.
IRIS MANUAL SETUP
▶IRIS VAL F1.6
END
2 If you choose ’MANUAL‘, select the optimal
shutter speed.
• In MANUAL mode, the optimal shutter speed
needs to be designated. Select from 1/60 to
1/120,000 (NTSC) or from 1/50 to 1/120,000
(PAL). * 'Sens-Up' mode can be configured
manually (2x to 256x).
• Verify changes made to the shutter speed by
referencing to changes in on screen brightness.
3 Press the SET button to complete.
SHUTTER MANUAL SETUP
▶SHUTTER VAL 1/60
END
Notes
• Image may become unstable if the camera is set to 'ESC' mode and faces a strong
fluorescent light.
• Under 'ESC' mode, the brightness can be adjusted using the LEFT or RIGHT button.
COLOR CCD CAMERA
26 User’s Manual
COLOR CCD CAMERA
27 User’s Manual
Operating Your Camera
AGC (Auto Gain Control) : For brighter images.
1 Position the indicator over 'AGC' using the UP or DOWN button.
2 Set 'AGC' to the desired mode using the LEFT or RIGHT button.
• HIGH
: Wide range gain value adjustment
• MEDIUM : MEDIUM range gain value adjustment
• LOW : Narrow range gain value adjustment
• MANUAL : Selecting gain value range. (5dB ~ 41dB)
• OFF : Disabled
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
AGC
SSNR
GAIN MANUAL SETUP
|
50
AUTO
ESC
MEDIUM
MEDIUM
|||||||||||| |||||||||||||
Notes
• Changing 'AGC' setting from LOW to HIGH results in greater sensitivity, as well as on
screen noise.
• Setting 'AGC' to OFF locks 'SSNR' configuration.
SENS-UP : This feature ensures clear images at night or under low lighting
conditions.
1 Position the indicator over 'SENS-UP' using the UP or DOWN button.
2 Set 'SENS-UP' to the desired mode using the LEFT or RIGHT button.
• AUTO : Select this mode for use in night time or under low lighting conditions.
• OFF : Disabled
▶LEVEL 5dB
END
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
AGC
SSNR
SENS-UP
SSNR(Samsung Super Noise Reduction): O
n screen noise reduction.
1 Position the indicator over 'SSNR' using the UP or DOWN button.
2 Set 'SSNR' to the desired mode using the LEFT or RIGHT button.
• LOW : Low noise reduction
• MEDIUM: Medium noise reduction
• HIGH : High noise reduction
• OFF : Disabled
COLOR CCD CAMERA
|||||||||||| |||||||||||||
Notes
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
AGC
SSNR
SENS-UP
50 |
AUTO
ESC
MEDIUM
MEDIUM
OFF
50 |
AUTO
ESC
MEDIUM
MEDIUM
OFF
|||||||||||| |||||||||||||
28 User’s Manual
• Once 'AUTO' mode is set, the user can configure Sens-Up limit by increasing /decreasing
the shutter speed (e.g.: X2,X4....... X32,X64,X128,X256).
• Enabling Sens-Up increases camera sensitivity and may result in additional noise and/or
other phenomenons. This is normal.
COLOR CCD CAMERA
29 User’s Manual
Operating Your Camera
• MASK TONE : Determine the transparency of selected area as controlling number from
0 to 3.
• END : Select this to save the PRIVACY menu settings and return to the
SPECIAL menu.
DAY/NIGHT :You can display pictures in color or black and white.
SPECIAL
MAIN SETUP
WHITE BAL
ATW
BACKLIGHT
OFF
MOTION DET
OFF
FOCUS
EXPOSURE
SPECIAL
RESET
1. Press the SET button to access the main setup menu and then position the
indicator over 'SPECIAL' using the UP or DOWN button.
2. Press the SET button to confirm.
PRIVACY :Hide an area you want to hide on the screen.
PRIVACY SETUP
▶AREA SEL
AREA1
AREA MODE ON
MASK COLOR GRAY
MASK TONE 0 |
END
|||||||||||||||||||||||||
2 Set up the mode using the 4 direction buttons.
COLOR CCD CAMERA
30 User’s Manual
Down buttons so that the arrow indicates 'DAY/NIGHT'.
display you want.
• COLOR : The picture is always displayed in color.
• B/W : The picture is always displayed in black and white.
• AUTO : The mode is switched to 'Color' in a normal environment, but
switches to 'B/W' mode when ambient illumination is low. To set up
the sswitching time or speed for AUTO mode, press the SET button.
1 When the SPECIAL menu screen is displayed, press
• AREA SEL : You can select up to 8 MD areas.
• AREA MODE : D
etermines whether to use the
area selected in the AREA SEL, and
the size and position of the area.
• MASK COLOR :Determine area color. You can select
Gray, Green, Red, Blue, Black, White.
1 When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Up and
2 Select a desired mode using the Left and Right buttons according to the picture
SPECIAL SETUP
PRIVACY
OFF
DAY/NIGHT
AUTO
DIS
OFF
the Up and Down buttons so that the arrow
indicates ‘PRIVACY’.
SPECIAL SETUP
PRIVACY
OFF
DAY/NIGHT
AUTO
DIS
OFF COMM ADJ
- DWELL TIME : You can select the duration time
about changing the day/night mode.
→ 5,7,10,15,20,30,40, 60(sec)
- DURATION : You can select brightness of
illumination about changing the
day/night mode.
DAY/NIGHT AUTO SETUP
▶DWELL TIME 5 SEC
DURATION
FAST
END
AREA SETUP
▶TOP
BOTTOM
LEFT
RIGHT
END
45
110
20
20
70
||||||||||||||||||||||||||
||||||||||||||||||||||||||
||||||||||||||||||||||||||
|||||||||||||||||||||||||
Fast
Slow
Color → B/W
2.5 lux
0.8 lux
B/W → Color
4 lux
6 lux
||||||||||||||||||||||||||
• EXT : This mode allows you to apply a desired filter to external signals.
COLOR CCD CAMERA
31 User’s Manual
Operating Your Camera
Notes
• When using a Video Auto Iris Lens, if you set the lens level to low, automatic switching
between Color and Black & White may not occur.
• You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu is ‘OFF’.
At this time, the exchange between DAY mode and NIGHT mode operates as like selecting
‘COLOR’ mode.
• The OSD key does not work for 3 seconds when switching to Color or B/W, to ensure
stable camera operation.
• The camera may focus less well under infrared illumination than under normal illumination.
• Since the camera may not focus as well under infrared illumination at night as it does
under normal illumination, install an Extra-low Dispersion Lens to obtain sharp pictures.
• The brightness of illumination is changeable by installed environment.
DIS : T he DIS mode can compensate for vibration of the camera.
SPECIAL SETUP
PRIVACY
OFF
DAY/NIGHT
COLOR
DIS
OFF
COMM ADJ
(between 0 and 255).
: Select the communication PROTOCOL. (STW/PELCO-D/PELCO-P/
BOSCH/HONEYWELL/VICON/AD/SEC/PANASONIC)
• BAUD RATE : You can select 2400/4800/9600/19200/38400/57600/115200 bps.
• UART MODE : You can select NONE, EVEN or ODD for the parity bits.
• TERMINATION : Function that sets the resistance at the end of RS-485
communications.
• Protocol ✽ Setting Termination Resistance.
In order to prevent signal reduction, the termination resistance of the 2 end units,
which are the distant paths for camera and controller to be connected on the RS485
interface, should be connected.
As the termination resistance is built in the camera, whether to make the termination
resistance valid or invalid is selected with the TERMINATION.
See the connection diagram for determining to which device the termination
resistance will be connected to.
Set up the termination resistance in the dark products.
The installation distance of the product for the termination resistance setting should
be less than 1.2 Km. (Maximum cable length is 1.2 Km according to the RS-485
standards.)
Notes
• When DIS is operating, D-ZOOM does not operate.
COMM ADJ (Communication Adjustment) :
This function sets up the camera communication
status when controlling the camera through an
external control device.
COMMUNICATION SETUP
▶PROTOCOL
CAM ID
BAUD RATE
UART MODE
TERMINATON
RET PKT
END
STW
1|
9600
8-N-1
OFF
DISABLE
|||||||||||||||||||||||||
1 When the SPECIAL menu screen is displayed, press
the Up and Down buttons so that the arrow indicates ‘COMM ADJ’.
2 Set up the mode using the 4 direction buttons.
• CAM ID : Determines the camera's identification number
COLOR CCD CAMERA
32 User’s Manual
COLOR CCD CAMERA
33 User’s Manual
Operating Your Camera
• RET PKT
: You can choose whether to send an ACK signal when the
communication control command is issued to the camera.
• COLOR • END
Notes
• If Camera is controlled by the Vicon Controller,function button may not work properly.
: Adjusting this value affects the chroma level only; the burst level
is unaffected.
: evert back to the USER PRESET menu.
DISPLAY : Use this feature to designate a name for the camera, which will display
on the monitor screen
IMAGE ADJ : Includes image quality or special function factors.
SPECIAL SETUP
PRIVACY
OFF
DAY/NIGHT
COLOR
DIS
OFF
SYNC
INT
COMM ADJ
IMAGE ADJ
DISPLAY
1 When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the Up and
SPECIAL SETUP
PRIVACY
OFF
DAY/NIGHT
COLOR
DIS
OFF
SYNC
INT
COMM ADJ
IMAGE ADJ
DISPLAY
END
Down buttons so that the arrow indicates 'IMAGE ADJ.
2 Select a desired mode using the Up and Down buttons.
•H
-REV : You can flip the picture horizontally
on the screen.
• V-REV : You can flip the picture vertically on
the screen.
• S HARPNESS : As you increase this value, the picture
outline becomes stronger and clearer.
CAM TITLE
IMAGE SETUP
▶H-REV
V-REV
SHARPNESS
COLOR
END
OFF
OFF
ON
50
Notes
▶LEVEL
END
34 User’s Manual
to ‘CAM TITLE’ using the UP or DOWN button.
2 Set ‘CAM TITLE’ to ‘ON’ using the LEFT or RIGHT button.
||||||||||||||||||||||||
SHARPNESS SETUP
COLOR CCD CAMERA
1 Press the SET button to display the main setup menu and move the arrow indicator
16
• If the CAM TITLE feature is set to ‘OFF’,
the name will not displayed in the monitor
||||||||||||||||||||||||
COLOR CCD CAMERA
DISPLAY SETUP
▶CAM TITLE
CAM ID
CAM INFO
MD ALARM
ZOOM MAG
LANGUAGE
END
35 User’s Manual
OFF
ON
ON
----ON
ENGLISH
Operating Your Camera
3 Press SET button.
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
0123456789 ( )
< >-/#¬S!?,.
←→ CLR POS END
• LANGUAGE • END UP or Down button. Then set to ON using the LEFT or RIGHT
button.
: You can select the menu language according to your
requirements (Korean, ESPANOL, FRANCAIS, ITALIANO,
DEUTSCH, ENGLISH, Japanese, Chinese)
: Select this to save the SPECIAL menu settings and return to the
SPECIAL menu.
4 You can enter up to 20 characters.
a. Move the cursor to the character entry field using the LEFT or RIGHT button.
b. Use UP, DOWN, LEFT and RIGHT buttons to select a desired character.
c. Press the SET button to confirm selection of the blinking character. The character
is then saved, and the cursor in the entry field moves to the next position.
d. Repeat steps a through c until the desired name has been entered.
RESET
To reset your camera to factory default condition.
EXIT
Notes
• Correcting Mistakes
Move the cursor th ‘CLR’ and press the SET button to clear the entire entry. To modify one
character, use LEFT or RIGHT to position the cursor above the character to be modified and
click the SET button after selecting the character to enter.
To finish setup menu.
Troubleshooting
5 Enter a title, move the cursor to ‘POS’ and press
the SET button. The entered title appears on the
screen. Select the position to display the title on the
screen by using the 4 direction butons and press
the SET button.
When the position is determined, select.
FRONT DOOR
• CAM ID : Displays camera ID on top left corner of the screen.
• CAM INFO : Displays camera information on screen.
• MOTION ALARM : You can toggle the use of the camera alarm.
• ZOOM MAG : Use this feature to display the current zoom magnification level
on screen. Position the indicator over ‘ZOOM MAG’ using the
COLOR CCD CAMERA
36 User’s Manual
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized
technician.
• Nothing appears on the screen.
- Check that the power cord and line connection between the camera and monitor are
fixed properly.
- Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
• The image on the screen is dim.
- Is lens stained with dirt? Clean your lens with soft, clean cloth.
- Set the monitor to proper condition.
- If the camera is exposed to too strong light, change the camera position.
COLOR CCD CAMERA
37 User’s Manual
Troubleshooting
Specifications
• The image on the screen is dark.
- Adjust the contrast feature of the monitor.
- If you have an intermediate device, set the 75Ω / Hi-z properly.
• The camera is not working properly, and the surface of the camera is hot.
- Check that you have properly connected the camera to an appropriate power source.
• The DAY/NIGHT menu does not work.
- Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
• The SENS-UP function does not work.
- Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
- Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’.
• The Motion Detection function does not work.
- Check that MOTION DEF of SPECIAL SETUP menu is ‘OFF’.
• Color is not correct.
- Check the setting of WHITE BAL SETUP menu .
• The screen flickers continually.
- Check that direction of camera turns toward the Sun.
• RS-485 communication fails.
- Check the polarity between RS-485 Control Port and RS-485 cable.
485 Control Board Connection Port
RS-485 Control Port
(+) CONNECTION TERMINAL (TRX+)
485+
( - ) CONNECTION TERMINAL (TRX-)
485-
- Check the RS-485 Communication establishment initial value
* RS-485 Communication establishment initial value
Item
Initial value
Camera ID
1
BAUD RATE
9600
UART MODE
8-NONE-1
RET PKT
DISABLE
- We recommend that you make ground connect between camera and controller in order to
maintain safety communication control.
COLOR CCD CAMERA
38 User’s Manual
SDZ-370N
Input Voltage
POWER
Power Consumption
Size
Total Pixels
Effective Pixels
O
Optics
P
Min. Focus Distance
T
I
D. ZOOM
C
Angle Field of view
S
Scanning System
Sync. Synchronization
Frequency
Resolution
Min. Illumination
S/N (Y signal)
Video Output
Focus
Zoom Movement Speed
IRIS Control
Lens Initialize
Camera Title
CCD
E
L
E
C
T
R
I
C
A
L
Camera ID
Day & Night
Gain Control
White Balance
BACK LIGHT
Shutter Speed
O.S.D
Motion Detection
Control Output
SSNR
Privacy Function
FLIP
MIRROR
DIS
PRESET
PROTOCOL
Operating Temperature/Humidity
Storge Temperature/Humidity
Dimension
Weight
SDZ-370P
DC 10.8V ~ 13.2V (Recommended : 12V )
2.8 W : Steady-state (at 12V)
5.1 W : Max. (Zoom, Focus, Day&night motor operating, at 12V)
1/4 Inch, Super HAD color CCD
811(H) x 508(V)
795(H) x 596(V)
768(H) x 494(V)
752(H) x 582(V)
37X, f=3.5 to 129.5mm(F1.6 to 3.9)
1500mm
OFF/ON (Limit 12x)
H : Appr. 55.5˚(Wide) to 1.59˚(Tele) V : Appr. 42.5˚(Wide) to 1.19˚(Tele)
2:1 Interlace
Internal
H: 15.734KHz / V: 59.94Hz
H: 15.625KHz / V: 50.00Hz
550 TV Lines(Min.) : Color / 680 TV Lines(Min.) : B/W
0.4 Lux/F1.6(50IRE): Color/0.02 Lux/F1.6(50IRE): B/W
50 dB
CVBS (1.0Vp-p/75Ω)
AUTO/MANUAL/ONE-PUSH
2.5 Sec
AUTO/MANUAL
Built-In
ON/OFF
256EA
AUTO/COLOR/BW/EXT
LOW/MEDIUM/HIGH/MANUAL/OFF
ATW/AWC/MANUAL/INDOOR/OUTDOOR
BLC/HLC/OFF
AUTO/MANUAL/A.FLK
KOREAN,ESPANOL,FRANCAIS,ITALIANO,DEUTSCH,ENGLISH,JAPANESE,
CHINESE : total 8 language
ON/OFF
RS-485 (2400/4800/9600/19200/38400/57600/115200bps)
LOW/MEDIUM/HIGH/OFF
ON/OFF (8 Zones)
ON/OFF
ON/OFF
ON/OFF
128 Positions
STW, PELCO-D, PELCO-P, SEC, PANASONIC, VICON, AD, HONEYWELL, BOSCH
-10˚C to +50˚C / 20% to 80% RH
-20˚C to +60˚C / 20% to 95% RH
67.6(W)X67.6(H)X124.7(D) mm
450g
COLOR CCD CAMERA
39 User’s Manual
Note
(AGC OFF, Weight ON)
Wide to Tele
20 characters
ID:000 ->
Remote only
IR-Cut Filter
Removable
1/120,000sec~X256
STW Protocol Command Description
Command Name
Command Packet
Return Packet
Checksum
Reset
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Parameter
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Focus Far
Focus Near
Zoom Wide
Zoom Tele
ZOOM Direct
AF Stop
One push AF
COLOR CCD CAMERA
40 User’s Manual
Byte1
Byte2
Byte3
STX
CAM ID
HOST ADDR
STX
CAM ID
HOST ADDR
CHECKSUM CALCULATION: UNARY OPERATION
EX) CHECKSUM = ~(BYTE2+BYTE3+... +BYTE8+
Reset all data to factory default value.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move focus lens to far direction.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move focus lens to near direction.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move zoom lens to wide direction.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move wide lens to tele direction.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move ZOOM lens to specific position directly
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
P1, P2: OPTICAL ZOOM = 0000h~06EAh
P3: DIGITAL ZOOM = ((256*10)/Ratio)-1
ex) D-ZOOM 1.1x : P3 = E7h = ((256*10)/11)-1,
D-ZOOM 2.0x : P3 = 7Fh = ((256*10)/20)-1,
Stop zoom & focus lens moving.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Unconditionally execute auto focus.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Byte4 ll Byte5
Byte 6
Byte7
CAMMAND
DATA3
DATA4
CAMMAND
DATA3
DATA4
OF SUMMATION FROM BYTE2 TO BYTE9.
BYTE9);
Byte8
DATA5
DATA5
Byte9
DATA6
DATA6
Byte10
ETX
ETX
Byte11
CHECKSUM
CHECKSUM
000Fh
000Fh
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0100h
0100h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0200h
0200h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0040h
0040h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0020h
0020h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
00FFh 00FFh P1
P1
P2
P2
P3
P3
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0000h
0000h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0045h
0045h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
Ratio 11 means 1.1x.
Ratio 20 means 2.0x.
COLOR CCD CAMERA
41 User’s Manual
STW Protocol Command Description
User Preset Save
User Preset Exec.
User Preset Clear
Function
Command Packet
Return Packet
Parameter
Function
Command Packet
Return Packet
Parameter
Function
Command Packet
Return Packet
Parameter
Function
OSD Menu On/Off
Command Packet
Return Packet
Parameter
COLOR CCD CAMERA
Save current user preset configuration information.
A0h
CAM ID
HOST ADDR
0003h
A0h
CAM ID
HOST ADDR
0003h
P1:00h(USER PRESET 1) ~80h(USER PRES ET 128)
Execute selected user preset.
A0h
CAM ID
HOST ADDR
0007h
A0h
CAM ID
HOST ADDR
0007h
P1:00h(USER PRESET 1) ~80h(USER PRES ET 128)
Clear selected user preset.
A0h
CAM ID
HOST ADDR
0005h
A0h
CAM ID
HOST ADDR
0005h
P1:00h(USER PRESET 1) ~80h(USER PRES ET 128)
Display OSD menu on the screen.
Clear OSD menu and save current menu setup.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
P1: 00h = ON
00B1h
00B1h
P1
P1
00h
00h
00h
00h
00h
00h
Afh
Afh
CHECK SUM
CHECK SUM
P1
P1
00h
00h
00h
00h
00h
00h
Afh
Afh
CHECK SUM
CHECK SUM
P1
P1
00h
00h
00h
00h
00h
00h
Afh
Afh
CHECK SUM
CHECK SUM
P1
P1
00h
00h
00h
00h
00h
00h
Afh
Afh
CHECK SUM
CHECK SUM
01h = OFF
42 User’s Manual
COLOR CCD CAMERA
43 User’s Manual
STW Protocol Command Description
OSD Menu Up
OSD Menu Down
OSD Menu Left
OSD Menu Right
OSD Menu Set
OSD Menu ESC
Function
Move OSD arrow to up.
Command Packet
A0h
CAM ID
HOST ADDR
0008h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0008h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Move OSD arrow to down.
Command Packet
A0h
CAM ID
HOST ADDR
0010h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0010h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Move OSD arrow to left.
Command Packet
A0h
CAM ID
HOST ADDR
0004h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0004h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Move OSD arrow to right.
Command Packet
A0h
CAM ID
HOST ADDR
0002h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0002h
00h
00h
00h
00h
AFh
CHECK SUM
Functio
Move to inside menu
Command Packet
A0h
CAM ID
HOST ADDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Move to upper menu.
Command Packet
A0h
CAM ID
HOST ADDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
COLOR CCD CAMERA
44 User’s Manual
COLOR CCD CAMERA
45 User’s Manual
DECLARATION OF CONFORMITY
Application of Council Directive(s)
89 / 336 / EEC
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-716
MEMO
European Representative Name
European Representative Address
Equipment Type/Environment CCTV Camera
Model Name SDZ-370N,SDZ-370P
Beginning Serial NO. S6400001
Year of Manufacture 2008. 4. 1
Conformance to EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe
Signature Signature
Full Name HAN SEUG KIM
Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON, KOREA
Place
Date 2008. 4. 1
Date
COLOR CCD CAMERA
46 User’s Manual
COLOR CCD CAMERA
47 User’s Manual
SALES NETWORK
•
AMSUNG TECHWIN CO., LTD.
S
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703
TEL : +82-31-740-8151~8 FAX : +82-31-740-8145
•
AMSUNG TECHWIN AMERICA Inc.
S
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222 FAX : +1-310-632-2195
www.samsungcctvusa.com
•
AMSUNG TECHWIN EUROPE CO., LTD.
S
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
www.samsungtechwin.com
www.samsungcctv.com
P/No. : Z6806094901A
VAN 09. 02