Acer 3300 Laptop Service Guide

Acer TravelMate 3300/Extensa 3100 Series

Service Guide

Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.tw

PRINTED IN TAIWAN

II

Revision History

Please refer to the table below for the updates made on TravelMate 3300/Extensa 3100 service guide.

Date

2005/11/25

2005/12/15

All

Chapter 1

Chapter Updates

Revise TravelMate 3300/Extensa 3100 battery spec. on page 25 and page 26.

Add “WFM” to BIOS support protocols on page 23.

Copyright

Copyright © 2005 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.

Disclaimer

The information in this guide is subject to change without notice.

Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.

Acer is a registered trademark of Acer Corporation.

Intel is a registered trademark of Intel Corporation.

Pentium and Pentium II/III are trademarks of Intel Corporation.

Other brand and product names are trademarks and/or registered trademarks of their respective holders.

III

Conventions

The following conventions are used in this manual:

SCREEN MESSAGES

NOTE

WARNING

CAUTION

IMPORTANT

Denotes actual messages that appear on screen.

Gives bits and pieces of additional information related to the current topic.

Alerts you to any damage that might result from doing or not doing specific actions.

Gives precautionary measures to avoid possible hardware or software problems.

Reminds you to do specific actions relevant to the accomplishment of procedures.

IV

Preface

Before using this information and the product it supports, please read the following general information.

1.

This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details.

2.

Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service

Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

V

VI

Chapter 1

System Specifications

Features

This computer was designed with the user in mind. Here are just a few of its many features:

Performance

T

T

Intel

®

915GM PCI Express chipset

Intel

®

Pentium

®

M processor 740/750/760/770/780 (2MB L2 cache, 1.60/1.73/1.86/2/2.13/2.26

GHz, 533 MHz FSB)

T

T

T

Intel

®

Celeron

®

M processor 360/370/380 (1MB L2 cache, 1.40/1.50/1.60 GHz, 400 MHz FSB)

CPU Package is uFPGA 478 Package

Integrated Intel

®

PRO/Wireless 2200BG network connection (dual-mode 802.11b/g) Wi-Fi

CERTIFIED

TM

solution

Memory

T

T

T

256MB or 512MB of DDRII 400/533

Upgradeable to 2GB Memory by Dual channels of SODIMM

512KB flash ROM BIOS

Display and graphics

T

14.1” WXGA Acer Crystallbrite clolor TFT LCD: 1280x 800 resolution

T

T

14.1” WXGA clolor TFT LCD: 1280x 800 resolution

16.7 million colors

T

T

Intel

®

915GM integrated 3D graphics, featuring Intel

®

Graphics Media Accelerator 900 and up to

128 MB of VRAM, supporting Microsoft

®

DirectX

®

9.0 and dual independent display

MPEG-2/DVD hardware-assisted capability

Audio

T

T

T

T

T

Audio system with two built-in speakers

Intel

®

AC’97 audio support

Sound Blaster Pro and MS Sound compatible

Built-in microphone

S/PDIF (Sony/Philips Digital interface)

Storage

T

T

T

40/60/80/100/12060 GB ATA/100 hard disc drive

Optical drive options: DVD-Dual double-layer or DVD/CD-RW combo

5-in-1 card reader (MS/MS PRO/MMC/SD/XD)

Communication

T

T

56Kbps ITU V92 with PTT approval; Wake-on-Ring ready

LAN: gigabit Ethernet; Wake-on-Ring ready

Chapter 1 1

T

T

WLAN (optional):

T

T

Integrated Intel

®

PRO/Wireless 2200BG network connection (dual-band 802.11b/g) Wi-Fi

CERTIFIED

TM

solution, supporting Acer SignalUp

TM

wireless technology, or

Integrated Acer InviLink

TM

802.11b/g Wi-Fi CERTIFIED

TM

solution, supporting Acer

SignalUp

TM

wirelss technology

WPAN (optional): Integrated Bluetooth

®

I/O Ports

T

T

T

T

T

T

T

T

T

T

T

T

T

T

Three USB 2.0 port

5-in-1 card reader (MS/MS PRO/MMC/SD/XD)

One Type II PC Card slot

IEEE 1394 port (6-pin)

Fast infrared (FIR) port

External display (VGA) port

Headphones/speaker/line-out port with S/PDIF support

Microphone-in jack

Line-in jack

Ethernet (RJ-45) port

Modem (RJ-11) port

DC-in jack (AC adapter)

One external monitor port

124-pin Acer ezDock connector

Dimensions and weight

T

330(W) x 240(D) x 23/31.3(H) mm (12.9 x 9.45 x 10.91/1.23 inches)

T

1.9Kg (4.23 lbs)

Environment

T

Temperature

T

T

T

Operating: 5 o

C ~ 35 o

C

Non-operating: -20 o

C ~ 65 o

C

Humidity ( non-condensing)

T

Operating: 20% ~ 80% RH

T

Non-operating: 20% ~ 80% RH

2 Chapter 1

Mainboard Layout

Top View

3

4

1

2

5

Fan Connector (FAN1)

LCD Cable Connector (LCD1)

IEEE 1394 Connector (SKT1)

USB Port (SKT2)

PC Card Slot (PCH1 or U22)

8

9

6

7

10

5-in-1 Card Reader Slot (CARD1)

RTC Battery Connector (RTC1)

Bluetooth Module Connector (BT1)

Touchpad FFC Connector (TPAD1)

Keyboard Connector (KB1)

Chapter 1 3

Bottom View

4

1

2

3

4

5

6

7

8

9

19

Giga LAN Port (JK1)

Power Jack (DCIN1)

VGA Port (CRT1) ezDock Port (DOCK1)

IO Controller-PC 87392 (U27)

Wireless LAN Card Slot (WIN1)

Keyboard Controller (U32)

LAN Controller-BROADCOM

BCM5788M (U31)

Battery Connector (BAT1)

Power Generator-IDT CV125PA

(U41)

10

11

12

13

14

15

16

17

18

Main Board to IO Board Connector

(IOB1)

HDD Connector (HDD1)

DIMM Slot (DM2)

DIMM Slot (DM1)

South Bridge-Intel ICH6-M (U44)

Switch (SW8)

Cardbus/1394/Card Reader

Controller-UltraMedia PCI 7411

(U52)

North Bridge (U34)

CPU (U33)

Chapter 1

IO Board Layout

Top View

3

4

1

2

5

6

Microphone Connector (INTMIC1)

Cover Switch Cable Connector

(LID1)

Audio Codec-Realtek ALC655 (U1)

IO Board to Main Board Connector

(BTB1)

Speaker Set Connector (SPKR1)

Line-out Port (LOUT1)

7

8

9

10

11

12

Microphone-in Port (MIC1)

Line-in Port (LINT1)

USB Port (USB1)

USB Port (USB2)

FIR (U6)

RJ11 Modem Jack (JK1)

Chapter 1 5

Bottom View

6

1 Modem Board Connector (MDC 1) 2 MDC Cable Connector (RING1)

Chapter 1

System Block Diagram

PATA

Chapter 1 7

Outlook View

A general introduction of ports allow you to connect peripheral devices, as you would with a desktop PC.

Front View

8

4

5

1

2

3

8

9

6

7

# Item

Display screen

Microphone

Status indicators

Touchpad

Description

Also called Liquid-Crystal Display (LCD), displaying computer output.

Internal microphone for sound recording.

Light-Emitting Diodes (LEDs) that turn on and off to show the status of the computer’s functions and components

Touch-sensitive pointing device which functions like a computer mouse.

The left and right buttons function like the left and right mouse buttons; the center button serves as a 4-way scroll button.

Click buttons

(Left, center and right)

Palmrest

Keyboard

Power button

Easy-launch buttons

Comfortable support area for your hands when you use the computer.

For entering data into your computer.

Turns the computer on and off.

Buttons for launching frequently used programs.

Chapter 1

# Item

# Item

Description

Description

# Item

Closed front view

"Launch keys" on page 10



4

5

6

1

2

#

#

#

Icon

Item

Item

Battery indicator

# Icon Item

3 Power indicator

Description

Description

Description

Lights up when the battery is being charged.

Description

Lights up when the computer is on.

7

Latch

5-in-1 card reader

Bluetooth communication button/ indicator

Locks and releases the lid.

Accepts Memory Stick, Memory stick Pro,

MultiMedia card (MMC), Sedure Digital (SD) and xD-Picture Card.

Note: Only one care can operate at any given time.

Press to enable/disable Bluetooth function. Lights to indicate the status of Bluetooth communications.

(for TM4600 only)

Wireless communications button/indicator

Press to enable/disable Wireless function. Lights to indicate the status of wireless LAN communications. (manufacturing option)

Left View

Chapter 1 9

# Icon Item Description

Note:

# Item Description


# Item Description

# Item

# Icon Item

# Icon

# Icon Item

Item Description

Description

Description

# Icon Item

Note:

Description

1

#

# Icon Item

Item

Kensington lock slot Connects to a Kensington-compatible

2 Modem (RJ-11) port Connects to a phone line.

5

6

3

4

# Icon

Infrared port

Item

Two USB 2.0 ports

Interfaces with infrared devices (e.g., infrared printer and IR-aware computer).

Description

Connect to USB 2.0 devices (e.g., USB mouse,

USB camera).

Line-in jack Accepts audio line-in devices (e.g., audio CD player, stereo walkman).

Microphone jack Accepts input from external microphones.

7

# Icon

Headphones/speaker/

Item

Connects to audio line-out devices (e.g., speakers,

Description

NOTE: The positions of the AcerMedia indicator, eject button and emergency eject hole may differ depending on the optical drive module installed.

# Item Description

Right View

10 Chapter 1



Note:

Description # Icon Item

5

6

1

#

2

#

# Icon

Icon

Icon

Item

Item

PC Card slot eject button

PC Card slot

Item

Description

Description

Description

Connects to one Type II CardBus PC Card.

4

3

# Icon Item

USB 2.0 ports

(e.g., USB mouse, USB camera).

Description

Note:

IEEE 1394 port (6-pin) Connects to IEEE 1394 devices.

Ventilation slots

Network jack

7

# Icon Item

DC-in jack

Enable the computer to stay cool, even after prolonged use.

Connects to an Ethernet 10/100/1000-based network (for selected models).

Description

Connects to an AC adapter.

Rear View


1

# Item

#

#

Icon Item

External display port

Icon Item

# Icon Item

connector

Description

Description

Connects to a display device (e.g., external monitor, LCD projector).

Description

Battery bay Houses the computer’s battery pack.

Chapter 1 11


Bottom View

4

5

6

1

2

3

#

Battery bay

Battery lock

Cooling fan

Item

Mini PCI card bay

Memory and hard disk bay

Battery release latch

Description

Houses the computer’s battery pack.

Locks the battery in position.

Helps keep the computer cool.

Note: Do not cover or obstruct the opening of the fan.

Houses the computer’s Mimi PCI card.

Houses the computer’s main memory and hard disk (secured with screws).

Release the battery for removal.

12 Chapter 1

#

Indicators

panel.

# Item

# Item

Description




The power, battery and wireless communiction status indicators are visible even when the LCd display is closed.

Icon Item

Caps Lock activity

Description

Lights when Caps Lock is activated.

# Icon

Num Lock activiy

Item

# Icon Item

Media activity

# Icon Item

Battery

Lights when Num Lock is activated.

Description

Lights when the hard disk or optical drive is active.

Description

Description

Lights up when the battery is being charged.

Power Lights up when the computer is on.

Bluetooth Indicates the status of Bluetooth communication.

Wireless LAN Indicates the status of wireless LAN communication.

NOTE: 1. Charging: The light shwos amber when the battery is charging. 2. Fully charged: The light shows green when in AC mode.

Chapter 1 13

Easy-launch buttons

Located at the upper-right, above the keyboard are four buttons. These buttons are called easy-launch buttons. The are: mail, Web Browser, Empowering Key < > and one user-programmable button.

Press < > to run the Acer Empowering Technology. The mail and Web browser buttons are pre-set to email and Internet programs, but can be reset by users.

Easy-launch button

Mail

Web browser

P

Default application

Email application (user-programmable)

Internet browser (user-programmable)

Acer Empowering Technology (user-programmable)

User-programmable

14 Chapter 1

Touchpad

The build-in touchpad is pointing device that senses movement on its surface. This means the cursor responds as you move your finger across the surface of the touchpad. The central location on the palmrest provides optimum comfort and support.

Touchpad Basics

Use the touchpad as follows:

T

T

T

Move your finger across the touchpad (2) to move the cursor.

Press the left (1) and right (4) buttons located on the edge of the touchpad to do selection and execution functions. These two buttons are similar to the left and right buttons on a mouse.

Tapping on the touchpad is the same as clicking the left button

Use the 4-way scroll (3) button to scroll up or down and move left or right a page. This button mimics your cursor pressing on the right scroll bar of windows applications.

Function

Execute

Select

Left button (1)

Quickly click twice.

Click one.

Right button (4) Main touchpad (2)

Tap twice (at the same speed as double-clicking a mouse button).

Tap once.

Center button (3)

Chapter 1 15

Drag

Function

Access context menu

Scroll

Left button (1)

Click and hold, then use finger on the touchpad to drag the cursor.

Right button (4) Main touchpad (2)

Tap twice (at the same speed as double-clicking a mouse button); rest your finger on the touchpad on the second tap and drag the cursor.

Center button (3)

Click one.

Click and hold to move up/down/left/ right.

16 Chapter 1

Using the Keyboard

The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and twelve function keys.

Lock Keys and embedded mumeric keypad

The keyboard has three lock keys which you can toggle on and off.

Lock Key

Caps Lock

Num lock

<Fn>+<F11>

Scroll lock

<Fn>+<F12>

Description

When Caps Lock is on, all alphabetic characters typed are in uppercase.

When Num Lock is on, the embedded keypad is in numeric mode. The keys function as a calculator

(complete with the arithmetic operators +, -, *, and /).

Use this mode when you need to do a lot of numeric data entry. A better solution would be to connect an external keypad.

When Scroll Lock is on, the screen moves one line up or down when you press the up or down arrow keys respectively. Scroll Lock does not work with some applications.

The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols are not printed on the keys.

Desired Access

Number keys on embedded keypad

Cursor-control keys on embedded keypad

Main keyboard keys

Num Lock On

Type numbers in a normal manner.

Hold <Shift> while using cursor-control keys.

Hold <Fn> while typing letters on embedded keypad.

Num Lock Off

Hold <Fn> while using cursor-control keys.

Type the letters in a normal manner.

Windows Keys

The keyboard has two keys that perform Windows-specific functions.

Chapter 1 17

Key

Windows key

Application key

Icon Description

Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the

Start menu. It can also be used with other keys to provide a variety of function:

+ <Tab> Activates next taskbar button.

+ <E> Opens the My Computer window

+ <F1> Opens Help and Support.

+ <F> Opens the Find: All Files dialog box.

+ <R> Opens the Run dialog box.

+ <M> Minimizes all windows.

<Shift>+ action.

+ <M> Undoes the minimize all windows

This key has the same effect as clicking the right mouse button; it opens the application’s context menu.

Hot Keys

The computer employs hotkeys or key combinations to access most of the computer’s controls like sreen brightness, volume output and the BIOS utility.

To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.

18

Hot Key

Fn-F1

Fn-F2

Fn-F3

Icon Function

Hot key help

Acer eSetting

Description

Displays help on hot keys.

Launches the Acer eSettings in Acer eManager.

Acer ePowerManagement

Launches the Acer ePowerManagement in Acer eManager.

Chapter 1

Fn-F7

Fn-F8

Fn-w

Fn-y

Hot Key

Fn-F4

Fn-F5

Fn-F6

Fn-x

Fn-z

Icon

Sleep

Function Description

Puts the computer in Sleep mode.

Display toggle

Screen blank

Touchpad toggle

Switches display output between the display screen, external monitor (if connected) and both.

Turns the display screen backlight off to save power.

Press any key to return.

Turns the internal touchpad on and off.

Speaker toggle Turns the speakers on and off.

Volume up

Volume down

Increases the speaker volume.

Decreases the speaker volume.

Brightness up Increases the screen brightness.

Brightness down Decreases the screen brightness

Special Key

You can locate the Euro symbol and US dollar sign at the upper-center and/or bottom-right of your keyboard.

To type:

Chapter 1 19

The Euro symbol

1.

Open a text editor or word processor.

2.

Either directly press the < > symbol at the bottom-right of the keyboard, or hold <Alt Gr> and then press the<5> symbol at the upper-center of the keyboard.

The US dollar sign

1.

Open a text editor or word processor.

2.

Either directly press the < > key at the bottom-right of the keyboard, or hold <Shift> and then press the

<4> key at the upper-center of the keyboard.

NOTE: This function varies by the operating system version.

NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/ typography/faq/faq12.htm for more information.

20 Chapter 1

Using System Utilities

Acer eManager

Innovative Acer eManagement software is designed for easy access to frequently used functions. At the press of Acer Empowering Key, the Acer eManager user interface appears, featuring four main settings -- Acer eSetting, Acer ePresentation, Acer ePowerManagement and Acer eRecovery.

Chapter 1

Icon

“Launch keys” on page 20

Acer eSetting

Item

Acer eSetting

Acer eSetting

Description



It is an easy way to manage the settings and security of

Acer ePresentation

It takes the hassle out of making presentations.

Acer ePresentation

Acer ePresentation





Acer eRecovery It backs up your files preventing data loss in the event of a

Acer eRecovery

Acer eRecovery

Acer eRecovery

21

Launch Manager

Launch Manager allows you to set the two launch keys located above the keyboard.

Launch Manager

22 Chapter 1

Hardware Specifications and Configurations

Processor

Item

CPU type

CPU package

CPU core voltage

CPU I/O voltage

Specification

Intel

®

Pentium

®

M processor 740/750/760/770/780 (2MB L2 cache, 1.73/

1.87/2.0/2.13/2.26 GHz, 533 MHz FSB)

Intel

®

Celeron

®

M processor 360/370/380 (1MB L2 cache, 1.4/1.5/1.6

GHz, 400 MHz FSB)

CPU on board no socket

Depend on DVI

1.2V

System Board Major Chips

Item

System core logic

Super I/O controller

Audio controller

Video controller

Hard disk drive controller

Keyboard controller

FIR controller

PCMCIA / card reader / 1394 controller

DDR-soDIMM controller

BIOS

Item

BIOS vendor

BIOS Version

BIOS ROM type

BIOS ROM size

BIOS package

Supported protocols

Intel

®

915GM / ICH6-M

NS 87392, LPC interface

Codec ALC655

UMA (built-in Intel

®

915GM)

ICH6-M

Renesas RE144B

NS 87392

TI PCI7411 built-in Intel

®

915GM

Controller

Specification

Phoenix

Flash ROM

512KB

32 lead of TSSOP

ACPI 2.0, PC Card 95, SMBIOS 2.3, IEEE1284-ECP/EPP, PCI 2.2, PnP

1.0a, DMI 2.0, PS/2 keyboard and mouse, USB 2.0, VGA BIOS, CD-ROM bootable, IEEE 1394, WFM 2.0 (Wired for Management)

Set by setup manual BIOS password control

L2 Cache

Cache controller

Cache size

Item

1st level cache control

2nd level cache control

Cache scheme control

Built-in CPU

2M (Intel

®

Pentium

®

M processor 740/750/760/770/780)

1M (Intel

®

Celeron

®

M processor 360/370/380)

Always enabled

Always enabled

Always enabled

Chapter 1 23

System Memory

Item

Memory controller

Memory size

DIMM socket number

Supports maximum memory size per slot

Supports maximum memory size

Supports DIMM type

Supports DIMM Speed

Supports DIMM voltage

Memory module combinations

.

LAN Interface

Item

Supports LAN protocol

LAN connector type

Wireless LAN

LAN connector location

.

Modem/Bluetooth Interface

Item

Data modem data baud rate (bps)

Supports modem/bluetooth protocol

Modem connector type

Modem connector location

Specification

Intel

®

915GM

256MB/512MB/1GB

2

1024 MB

2GB

DDRII SDRAM standard

400/533 MHz

1.8V

You can install memory modules in any combinations as long as they match the above specifications.

Specification

10/100/1000 Mbps Fast Ethernet connection

RJ45

InviLink. 802.11b/g dual-band

Right side

Specification

56K ITU

V.92 AC-Link modem with PTT approval

Wake-on-Ring ready

RJ11

Left side

VGA

Notice

Chipset for suitable VGA type Intel (R) 915GM

UMA

USB Port

Item

USB compliancy level

OHCI

Number of USB port

Location

2.0

USB 2.0

3

Right Side *1

Left Side *2

Specification

AC’ 97 Codec (ALC 655)

Specification

24

Audio Controller

Item

Chapter 1

Audio onboard or optional

Mono or Stereo

Resolution

Item

Compatibility

Mixed sound source

Sampling rate

Internal microphone

Internal speaker / Quantity

PCMCIA Port

Item

PCMCIA controller

Supports card type

Number of slots

Access location

Supports ZV (Zoomed Video) port

Supports 32 bit CardBus

Keyboard

Item

Keyboard controller

Keyboard vendor & model name

Total number of keypads

Touchpad with 4-way integrated scroll button

Function keys

Four easy-launch buttons

Two front access LED buttons

Specification

Built-in

Stereo

20 bit stereo Digital to analog converter

18 bit stereo Analog to Ditial converter

Microsoft PC99/2100, AC97 2.3 & WHQL/WLP2.0

CD

48 KHz

Yes

Yes / 2

TI PCI 7411

Type II

One type-II

Right Side

No

Yes

Specification

Specification

Renesas RE144B

Darfon

Standard keyboard with launch button embeded

T

88/85 keys PS/2 and AT-compatible keyboard

Yes

T

T

T

T

T

T

T

T

T

T

T

T four inverted “T“ cursor keys

Hot key controls (12 function keys) two Windows functions

Lock keys and embedded numeric keypad special keys international language support

Web Browser

Mail

Empowering key

One user-programmable button

WLAN LED button

Bluetooth LED button

Chapter 1 25

26

Battery

Item

Vendor & model name

Battery Type

Pack capacity

Cell voltage

Number of battery cell

Sony/Sanyo

Li-ion

53Wh

7200mAh for 9-cell

9-cell

Specification

NOTE: Extensa 3100 has second battery. When the battery is running out of power, the user can replace the battery with the second battery for prolong usage.

LCD 14.1” WXGA

Item

Vendor & model name

Screen Diagonal (mm)

Active Area (mm)

Display resolution (pixels)

Pixel Pitch

Pixel Arrangement

Display Mode (transmissive mode)

Typical White Luminance (cd/m

2

) also called Brightness

Luminance Uniformity

Contrast Ratio

Specification

CMO:

N141I1-L07 (non glare)

N141I1-L05 (glare)

N141C1-L02

(WXGA+)

358.14

303.36x189.6

303.48x189.675(for

WXGA+)

1280x800 WXGA

1440x900 WXGA+ for N141C1-L02

0.237x0.237

0.21075x0.21075

(WXGA+)

R.G.B. Vertical

Stripe

Normally White

185 (typ)

220 (typ for WXGA+

N/A

400 (Typ)

500 (Typ)

5/11 Response Time (Optical Rise Time/Fall

Time)msec

Power Supply Voltage

Typical Power Consumption (watt)

Weight

Physical Size(mm)

Electrical Interface

Support Color

+3.3V Typ.

4.02 for backlight unit only

400

319.5x205.5x5.2

1 channel LVDS

262K colors (RGB

6-bit data driver)

Viewing Angle (degree)

Horizontal: Right/Left

Vertial: Upper/Lower

45/45

20/45

QDI

QD14TL0102

358.14

303.7x189.8

1280x800

0.237x0.237

R.G.B. Vertical

Stripe

Normally White

185

1.25

300

10/15

+3.3V

N/A

440 (max)

319.5x205.5x5.2

1 channel LVDS

262,144

40/40

15/30

Hydis

HT141WX1-100

358.14

303.36x189.6

1280x800

0.237x0.237

R.G.B. Vertical

Stripe

Normally White

185

N/A

300

25

3.3V

390

319.5x205.5x5.2

1 channel LVDS

262,144

45/45

20/45

Chapter 1

LCD 14.1” WXGA

Item

Operating

Storage (shipping)

Specification

0 to +50

-20 to +60

0 to +50

-25 to +60

0 to +50

-20 to +60

Hard Disk Drive Interface

Item

Vendor &

Model Name

HGST Hakone

TOBHIBA Pluto

MK4025GAS

SEAGATE N2.1

ST9402112A

Capacity (MB) 40000

Bytes per sector

512

Data heads HGST Hakone

2 (Toshiba)

1 (Seagate)

Drive Format

Disks

Spindle speed

(RPM)

HGST Hakone

4200

/1/1

Performance Specifications

Buffer size HGST Hakone

Toshiba 8192KB

Seagate 2048KB

Interface HGST Hakone /ATA-

6/Parallel ATA

HGST Hakone /42.71/

56.25

Internal transfer rate

(Mbytes/sec. max.)

I/O data transfer rate

(Mbytes/sec. max.)

100 MB/Sec.

Ultra DMA mode 5

DC Power Requirements

Allowable voltage

5V(DC) +/- 5%

HGST Hakone

TOBHIBA Pluto

MK6025GAS

SEAGATE N2.2

ST960812A

60000

512

HGST Hakone

4 (Toshiba)

2 (Seagate)

HGST Hakone /2/1

4200

HGST Hakone

TOSHIBA Pluto

MK8025GAS

SEAGATE N2.2

ST980829A

80000

512

HGST Hakone

4 (Toshiba)

3 (Seagate)

HGST Hakone /2/2

4200

HGST Hakone

TOSHIBA Aries MK

1031GAS

SEAGATE N2.2

ST9100825A

100000

512

HGST Hakone

4 (Toshiba)

4 (Seagate)

HGST Hakone /2/2

4200

HGST Hakone

Toshiba 8192KB

Seagate 8192KB

HGST Hakone /ATA-

6/Parallel ATA

HGST Hakone /38.43/

56.25

HGST Hakone

Toshiba 8192KB

Seagate 8192KB

HGST Hakone /ATA-

6/Parallel ATA

HGST Hakone /42.71/

56.25

HGST Hakone

Toshiba 8192KB

Seagate 8192KB

HGST Hakone /ATA-

6/Parallel ATA

HGST Hakone /46.62/

56.25

100 MB/Sec.

Ultra DMA mode 5

5V(DC) +/- 5%

100 MB/Sec.

Ultra DMA mode 5

5V(DC) +/- 5%

100 MB/Sec.

Ultra DMA mode 5

5V(DC) +/- 5%

AC Adapter

Item

Vendor & model name

Input Requirements

Maximum input current (A,

@100Vac, full load)

Nominal frequency (Hz)

Frequency variation range (Hz)

Chapter 1

Specification

LITEON PA-1650-02WR (3pin, 65W)

LISHIN SLS0335A19A54LF (3pin, 65W)

1.8A [email protected]/100Vac and 240 Vac

47 - 63

47 - 63

27

28

AC Adapter

Item

Nominal voltages (Vrms)

Inrush current

Efficiency

Output Ratings (CV mode)

DC output voltage

Noise + Ripple

Output current

Output Ratings (CC mode)

DC output voltage

Constant output

Dynamic Output Characteristics

Start-up time

Hold up time

Over Voltage Protection (OVP)

Short circuit protection

Electrostatic discharge (ESD)

Dielectric Withstand Voltage

Primary to secondary

Leakage current

Regulatory Requirements

Specification

90 - 264

The maximum inrush current will be less than 50A and 100A when the adapter is connected to 100Vac(60Hz) and 240Vac(50Hz) respectively.

High efficiency 85% minimum, at 100~240Vac AC input, full load, warm-up condition.

Offers constant voltage 19.0V output source with 150W max output power capacity.

300mvp-pmax (20MHz bandwidth) for resistor load

0 A (min.) 3.5A (max.)

18.0 ~ 20.0

7.9A

3 sec. (@115 Vac and 230Vac full load)

5ms min. (@115 Vac input, full load)

25V

Output can be shorted without damage, and auto recovery

15kV (at air discharge)

8kV (at contact discharge)

4242 Vdc for 1 second-

60uA at 240Vac/60Hz

1. FCC class B requirements (USA)

2. VDE class B requirements (German)

3. VCCI classII requirements (Japan)

Power Management

ACPI Mode

Mech. Off (G3)

Soft Off (G2/S5)

Working (G0/S0)

Sleeping State (S3)

Sleeping State (S4)

Power Management

All devices in the system are turned off completely.

OS initiated shutdown. All devices in the system are turned off completely.

Individual devices such as the CPU and hard disk may be power managed in this state.

CPU Power Down

VGA Power Down

PCMCIA Suspend

Audio Power Down

Hard Disk Power Down

Super I/O Power Down

Also called Hibernate state. System saves all system states and data onto the disk prior to power off the whole system.

Dimensions and Weight

Item

Deminsions

Weight

Details

330(W) x 240(D) x 23/31.3(H) mm (12.9 x 9.45 x 10.91/1.23 inches)

1.9Kg (4.23 lbs)

Chapter 1

Environmental Requirements

Item

Temperature

Operating

Non-operating

Package storage

Humidity

Operating

Non-operating

Package storage

Altitude

+5°C ~ +35°C

-10°C ~ +60°C

-20°C ~ 60°C

20% ~ 85% RH

20% ~ 80% RH

20% ~ 90% RH

Operating sea level 0 to 10,000ft

Storage sea level 0 to 40,000ft

Specification

HDD Interface

Model Name

Data Storage Physical

Per drive, formatted

Data Heads

Number of Disks

Logical Configuration

Heads

Cylinders

User Sectors/Track at zone 0

Logical Blocks (LBA)

Data Transfer Rate

Max transfer rate to host

Seek Time

Track-to-track

Average

Maximum

MK4025GAS ,KA100A,

40GB

40.007GB

2

1

16

16,383

63

78,140,160

100MB/sec

2ms

12ms

22ms

Pluto MK6025GAS

60GB

60.0116GB

4

2

16

16,383

63

117,210,240

100MB/sec

2ms

12ms

22ms

Pluto MK8025GAS, 8MB,

80GB

80.012GB

4

2

16

16,383

63

156,301,488

100MB/sec

2ms

12ms

22ms

Chapter 1 29

30 Chapter 1

Chapter 2

System Utilities

BIOS Setup Utility

The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/

Output System).

Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4

Troubleshooting when problem arises.

To activate the BIOS Utility, press

m

during POST (when “Press <F2> to enter Setup” message is prompted

on the bottom of screen).

The setup screen displays BIOS as follows:Navigating the BIOS Utility

Information

Main

Function

Advanced

Security

Boot

Exit

Item

Display the system informations

Allows the user to specify standard IBM PC AT system parameters

Provides advanced settings of the system

Provides security settings of the system

Allows the user to specify the boot options

Allows the user to save CMOS setting and exit Setup

During setup,all Fn function keys and power saving functions are disabled.

There are five menu options: Main, Advanced, Security, Boot and Exit.

Follow these instructions:

T

To choose a menu, use the cursor left/right keys (zx).

T

T

T

T

To choose a parameter, use the cursor up/down keys ( wy).

To change the value of a parameter, press p or q.

Press ^ while you are in any of the menu options to go to the Exit menu.

In any menu, you can load default settings by pressing t. You can also press u to save any

changes made and exit the BIOS Setup Utility.

NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a

particular menu are shown on the bottom of the screen. Help for parameters are found in the Item

Specific Help part of the screen. Read this carefully when making changes to parameter values.

Chapter 2 31

Information

PhoenixBIOS Setup Utility

Information

CPU Type :

CPU Speed :

IDE1 Model Name :

Intel (R) Pentium (R) M processor 2.0GHz

2000MHz

ST9100825A - (PM)

IDE1 Serial Number : None

IDE2 Model Name : None

IDE2 Serial Number :

None

System BIOS Ver:

VGA BIOS Ver

V0.08

1232

KBC Ver

Serial Number

01.00

xxxxxxxxxxxxxxxxxxxxxx

Asset Tag Number

Produce Name

Manufacturer Name:

UUID:

N/A

TravelMate 3300/Extensa 3100

Acer xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

22 Byte

32 Byte

16 Byte

16 Byte

32 Byte

F1 Help ↑ ↓ Select Item F5/F6 Change Values F9 Setup Defaults

Esc Exit

→

Select Menu Enter Select

4

Sub - Menu F10 Save and Exit

Parameter

CPU Type

CPU Speed

IDE1 Model Name

IDE1 Serial Number

IDE2 Model Name

32

System BIOS Version

VGA BIOS Version

KBC Version

Description

This field displays the system CPU type.

This field displays the CPU speed of the system.

This item will show the Model name of HDD installed on Primary IDE master. The hard disk model name is automatically detected by the system. If there is no hard disk present or unknown type, “None” should be shown on this field

This item will show the Serial number of HDD installed on Primary IDE master. If no Hard disk or other devices are installed on Primary IDE master, then it will display a blank line

This item will show the model name of DVD/CD-ROM drive installed on system. The DVD/CD-ROM model name is automatically detected by the system. If there is no DVD/CD-ROM model present or unknown type, “None” should be shown on this field

This field reports the BIOS version of system

This field reports the VGA version of the system

This field reports the KBC version of the system.

Chapter 2

Parameter

Serial Number

Asset Tag Number

Product Name

Manufacturer Name

UUID

Description

This item will show the Serial number of system.

This item will show the Asset Tag number of the system.

This field will show product name.

This field will show manufacturer name.

This will be visible only when there is an internal LAN device present.

Chapter 2 33

Main


Information

Main

Advanced Security Boot Exit

Item Specific Help

System Time:

System Date:

System Memory:

Extended Memory:

Video Memory

Quiet Boot:

Power on display:

Network boot

F12 Boot Menu

D2D Recovery

[

23:47:44]

[

11/23/2005]

640 KB

<Tab>, <Shift-Tab>, or

<Enter> selects field.

Shows system base memory size

1022 MB

[128MB]

Shows extended memory size

VGA memory size

[Enabled]

[Auto ]

[Enabled]

[Disabled]

[Enabled]

34

F1 Help

↑ ↓

Select Item Change Values F9 Setup Defaults

Esc Exit

← →

Enter Select

4

Sub-Menu F10 Save and Exit

This menu provides you the information of the system.

Parameter

System Time / System

Date

System Memory

Extended Memory

Video Memory

Quiet Boot

Power on display

Description

The hours are displayed with 24 hours format. The values set in these two fields take effect immediately.

This field reports the memory size of system base memory. The size is fixed to

640KB.

This field reports the memory size of the extended memory in the system.

Extended Memory size = Total memory size - 1 MB

VGA Memory size = 128MB

Customer Logo display will be shown during POST when it is selected.

Auto: During power on process, the system will detect if any display device is connected on external video port. If any external display device is connected, the power on display will be in CRT (or projector) only mode.

Otherwise it will be in LCD only mode.

Both: Simultaneously enable both the integrated LCD screen and the system’s external video port (for an external CRT or projector).

Chapter 2

Parameter

Network boot

F12 Boot Menu

D2D Recovery

Description

When this is selected, Boot from LAN feature is enabled. When this is not selected, Boot from LAN feature is then disabled.

When this is selected, users can modify device boot priority by pressing F12 key during POST. When this is not selected, device boot priority will not be adjustable during POST.

Allow user to enable/disable the Disk-to-Disk recovery

Chapter 2 35

Advanced

The Advanced screen contains parameters involving your hardware devices. It also provides advanced

settings of the system.


Info.

Main

Advanced

Security Boot Exit

Infrared Port (FIR)

[Enabled]

Item Specific Help

Parallel port:

Serial port

[Enabled]

[Enabled]

Configure Infrared Port using options:

[Disable]

No configuration

[Enabled]

User configuration

[Auto]

BIOS or OS chooses

configuration

(OS Controlled)

Displayed when controlled

by OS


Esc Exit

← →

Enter

4

Sub - Menu F10 Save and Exit

The table below describes the parameters in the screen. Settings in boldface are the default and suggested

parameter settings.

Serial port A

Description

Configure serial port A using options:

[Disabled]: No configuration

[Enabled]: User configuration

[Auto]: BIOS or OS chooses configuration

(OS Controlled) Displayed when controlled by OS

Disabled

Enabled

Auto

Option

36 Chapter 2

Infrared Port

Parallel port

Mode

Description

Configure serial port B using options:




(OS Controlled) Displayedd when controlled by OS

Configure serial port B using options:




(OS Controlled) Displayedd when controlled by OS

Set the mode for the parallel port using options:

Output only Bi-directional

EPP

ECP

Disabled

Enabled

Auto

Disabled

Enabled

Auto

Option

Output only

Bi-directional

EPP

ECP

Chapter 2 37

Security

The Security screen contains parameters that help safeguard and protect your computer from unauthorized use.

Information


Security

Boot

User Password is :

Supervisor Password is :

Set User Password

Set Supervisor Password

Primary HardDisk Security

Password on Boot

Clear

Clear

[Enter]

[Enter]

[Disabled]

[Disabled]

Exit

Item Specific Help

Supervisor Password controls accesses of the whole setup utility.

It can be used to boot up when Password on boot is enabled.


Esc Exit

← →

Enter

4

Sub -Menu F10 Save and Exit

The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings.

Parameter

Supervisor Password Is

User Password Is

HDD Password Is

HDD Master ID


Set User Password

Description

N/A

N/A

N/A

N/A

Press Enter to set the administrator password. When set, this password protects the BIOS Setup Utility from unauthorized access.

[Set]: System password is set

[Clear]: System password is not set

Option

N/A

N/A

N/A

N/A

Length -- No more than 8 characters

Characters -- 0-9, A-Z (not case sensitive)

38 Chapter 2

Parameter

Set HDD Password

Password on boot

Description

When shown as [Locked], the hard drive password currently can not be changed or disabled.

To change or disable it, turn off the system and enter Setup immediately after turning it back on.

Press [Enter] to input change, or disable hard drive password.

Defines whether a password is required or not while the events defined in this group happened. The following suboptions are all requires the Supervisor password for changes and should be grayed out if the user password was used to enter setup.

Allows the user to specify whether or not a password is required to boot.

Enter

Disabled

Enabled

Option

Set Supervisor/User Password

If password on boot is required, the password must be set otherwise it cannot be enabled.

The formats of the password are as follows:

Length No more than 8 characters

Characters 0-9,A-Z (not case sensitive)

While these fields are highlighted and press “Enter”, a window similar to the following is shown:

Set SupervisorPassword

Enter New Password [ ]

Confirm New Password [ ]

If there is an old password then setup will prompt with the following window instead and a current password will be required to be entered at first:


Enter current password [ ]

Enter New Password [ ]

Confirm New Password [ ]

Chapter 2 39

40

User can now type password in field “Enter New Password”, and re-enter password in field “Confirm New

Password” for verification.

If the verification is OK:

The password setting is complete after user presses enter.

Setup Notice

Changes have been saved.

[ continue]

If the current password entered does not match the actual current password:

Setup Warning

Invalid password

Re-enter Password

[ continue]

If the new password and confirm new password strings do not match:

Setup Warning

Password do not match

Re-enter Password

Chapter 2

Boot

This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay and onboard LAN device.

Information


Main Security

Boot

+Hard Drive

Floppy Devices

CD-ROM/DVD Drive

Network Boot

Exit

Item Specific Help

Keys used to view or configure devices:

<Enter> to expands or collapses devices with a + or -

<F5> and <F6> moves the device up or down.


Esc Exit ← → Enter

4 Sub-Menu

F10 Save and Exit

Parameter

+Hard Drive

Floppy Devices

CD-ROM/DVD Drive

Netword Boot

.

Description

+ and - indicate device categories. Use <Enter> to expand/ collapse.

Boot order is top-down using only the top device in each category.

Use <F6> and <F5> to move highlighted item up and down.

Chapter 2 41

Exit

The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.


Information Main Security

Exit

Exit Saving Changes

Exit Disarding Changes

Load Setup Defaults

Discard Changes

Save Changes

Item Specific Help

Exit System Setup and save your changes to CMOS.

F1 Help

↑ ↓

Select Item F5/F6 Change Values F9 Setup Defaults

Esc Exit

← →

Enter

4 Sub-Menu

F10 Save and Exit

The table below describes the parameters in this screen.

Parameter

Exit Saving Changes

Exit Discarding

Changes

Load Setup Default

Discard Changes

Save Changes

Description

Exit System Setup and save your changes to CMOS

Exit utility without saving Setup data to CMOS

Load default values for all SETUP items

Load previous values from CMOS for all SETUP items

Save Setup Data to CMOS

42 Chapter 2

Chapter 3

Machine Disassembly and Replacement

This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting.

To disassemble the computer, you need the following tools:

T

Wrist grounding strap and conductive mat for preventing electrostatic discharge

T

T

Small Philips screw driver

Philips screwdriver

T

Plastic flat head screw driver

T

Tweezers

NOTE: The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components.

When you remove the stripe cover, please be careful not to scrape the cover.

Chapter 3 43

General Information

Before You Begin

Before proceeding with the disassembly procedure, make sure that you do the following:

1.

Turn off the power to the system and all peripherals.

2.

Unplug the AC adapter and all power and signal cables from the system.

3.

Remove the battery pack.

44 Chapter 3

Disassembly Procedure Flowchart

The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.

Start

Battery Pack

Memory

B*4

HDD Module

Wireless LAN

Card

A*1

HDD sponge

HDD copper

Touch Pad

Plate

I*5

Touch Pad

Chapter 3

Middle Cover

Keyboard

C*2

LCD Module

D*2

E*1

F*2

Upper Case

Assembly

G*1

H*15

Lower Case

Assembly

Bluetooth

Module

RTC Battery

Main Board

Assembly

J*2

K*2

Heatsink

Q*3

Fan

N*3

Front Cover

O*2

I/O Board

L*2

M*1

Speaker Set

Modem

Board

P*1

45

46

LCD Module

LCD Bezel

R*2

S*2

LCD Inverter

T*2

LCD

Assembly

U*2

2 hinges

V*2

LCD Brackets

X*8

LCD Cable

Wireless

Antenna Set

W*2

Screw List

Item

A

B

J

K

H

I

E

F

C

D

G

Description

SCW HEX NYL I#R-40/

O#4-40 L5.9

SCREW MACH WAFER

M2*L4 NI

86.T39V1.002

SCREW M2*L9 NYLOK 86.00D38.520

SCRW WH MS+CBZ

M2.5+L4 BLACK

86.9A323.4R0

SCREW M2.5-6

SCREW M2*3 NYLON

1JMCPC-420325

SCREW

M2.5*4L(NYLOCK)BLA

CK ZN

Part Number

34.4C210.001

86.9A323.6R0

86.9A352.3R0

86.9A353.4R0

SCREW M2.5X6

SRW M2.5*8L B/ZN

NYLOK 700

86.9A353.6R0

86.9A353.8R0

SCREW M2-3 86.9A522.3R0

SCRW M2*4 WAFER NI 86.9A552.4R0

LCD

Chapter 3

Removing the Battery Pack

1.

Release the battery lock.

2.

Slide the battery latch as shown then remove the battery pack.

Chapter 3 47

Removing the Wireless LAN Card/the memory and the HDD

Module and the LCD Module

Removing the Wireless LAN Card

1.

Remove the screw fastening the mini PCI cover.

2.

Detach teh mini PCI cover.

3.

Disconnect the main and the auxiliary wireless antenna.

4.

Pop out the wireless LAN card then remove it.

Removing the Memory and the HDD Module

1.

Remove the five screws that secure the HDD cover.

2.

Detach the HDD cover from the main unit.

48

3.

Pop up the memory then remove it.

4.

Lift up the HDD module then pull the HDD module backwards and remove it.

Chapter 3

.

Removing the LCD Module

1.

Open the notebook as shown.

2.

Detach the middle cover from the main unit.

3.

Remove the two screws that secure the keyboard.

4.

Turn over the keyboard as shown.

5.

Disconnect the keyboard cable then remove the keyboard.

6.

Tear off the tape fastening the wireless antenna, then pull out the antenna from the main unit.

7.

Disconnect the LCD cable from the main board.

8.

Close the LCD module and turn over the notebook, then remove two screws fastening the LCD module on the bottom as shown.

9.

Remove one screw holding the LCD module on the rear side.

Chapter 3 49

10. Then remove two screws fastening the LCD module.

11. Detach the LCD module from the main unit carefully.

50 Chapter 3

Disassembling the Main Unit

Separate the Main Unit Into the Upper and the Lower Case Assembly

1.

Disconnect the touchpad FFC from the main board.

2.

Disconnect the system fan cable from the main board.

3.

Remove one screw fastening the upper and the lower case assembly as shwon.

4.

Remove 15 screws fastening the upper and the lower case assembly on the bottom.

5.

Then detach the upper case assembly from the lower case assembly carefully.

Disassembling the Lower Case Assembly

1.

Disconnect the bluetooth cable from the main board then detach the bluetooth module.

2.

Disconnect the RTC battery cable from the main board then detach the RTC battery.

3.

Disconnect the speaker cable from the IO board.

4.

Disconnect the bluetooth cable from the bluetooth board.

Chapter 3 51

5.

Disconnect the microphone cablem from the IO board then detach the microphone.

6.

Disconnect the Lid switch cable from the IO board as shown.

7.

Remove the four screws fastening the mian board to the lower case.

8.

Remove two screws fastening the IO board and one screw holding the modem board.

9.

Detach the IO board from the lower case (The IO board is with modem board).

10. Remove the three screws fastening the system fan.

11. Remove the system fan from the lower case.

12. Remove the two screws that fasten the speaker set.

13. Detach the front cover from the lower case.

14. Remove the speaker set from the lower case.

15. Remove the four screws fastening the heatsink to the main board.

16. Detach the heatsink from the main board.

52

17. Remove the screw that fastens the modem board to the IO board.

Chapter 3

18. Disconnect the modem board from the IO board.

19. Disconnect the modem board cable from the modem board.

Disassembling the Upper Case Assembly

1.

Disconnect the touchpad FFC from the touchpad then remove it.

2.

Remove the five screws fastening the touchpad plate.

3.

Detach the scroll key rubber from the touchpad plate.

4.

Remove the touchpad plate.

5.

Then detach the touchpad from the upper case.

Chapter 3 53

Disassembling the LCD Module

1.

Remove the four screw caps as shown.

2.

Remove the four screws holding the LCD bezel.

3.

Then detach the LCD bezel from the LCD module.

4.

Remove the two screws fastening the inverter.

5.

Take the inverter out of the LCD panel then disconnect the LCD cable.

6.

Disconeect the LCD inverter cable on the other side then remove the inverter.

.

7.

Remove two screws fastening the LCD to the LCD panel.

8.

Detach the LCD from the LCD panel.

9.

Remove the two screws fastening the hinges to the LCD panel.

10. Remove the two hinges from the LCD panel.

11. Remove the two screws holding the wireless antenna set.

12. Then detach the wireless antenna set from the LCD panel.

54 Chapter 3

13. Remove the four screws fastening the LCD right bracket.

14. Detach the LCD right bracket from the LCD.

15. Remove the four screws fastening the LCD left bracket.

16. Detach the LCD left bracket from the LCD.

17. Tear off the tape fastening the LCD cable then disconnect the LCD cable.

Chapter 3 55

Disassembling the External Modules

Disassembling the HDD Module

1.

Detach the HDD sponge.

2.

Turn over the HDD module.

3.

Tear off the HDD module copper (shielding).

4.

Then detach the HDD from the HDD copper (shielding) as shown.

56 Chapter 3

Chapter 4

Troubleshooting

Use the following procedure as a guide for computer problems.

NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses.

1.

Obtain the failing symptoms in as much detail as possible.

2.

Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation.

Chapter 4 57

System Check Procedures

External Diskette Drive Check

Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is required.

NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause damage to the drive or cause the drive to fail.

Do the following to select the test device.

1.

Boot from the diagnostics diskette and start the diagnostics program.

2.

See if FDD Test is passed as the program runs to FDD Test.

3.

Follow the instructions in the message window.

If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.

If the error still remains:

1.

Reconnect the external diskette drive/DVD-ROM module.

2.

Replace the external diskette drive/CD-ROM module.

3.

Replace the main board.

External CD-ROM Drive Check

Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.

Do the following to select the test device:

1.

Boot from the diagnostics diskette and start the diagnostics program.

2.

See if CD-ROM Test is passed when the program runs to CD-ROM Test.

3.


If an error occurs, reconnect the connector on the System board. If the error still remains:

1.

Reconnect the external diskette drive/CD-ROM module.

2.

Replace the external diskette drive/CD-ROM module.

3.


Keyboard or Auxiliary Input Device Check

Remove the external keyboard if the internal keyboard is to be tested.

If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable extending from the keyboard is correctly seated in the connector on the system board.

If the keyboard cable connection is correct, run the Keyboard Test.

If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a non-defective FRU:

1.

Reconnect the keyboard cables.

2.

Replace the keyboard.

3.


58

The following auxiliary input devices are supported by this computer:

T

Numeric keypad

T

External keyboard

If any of these devices do not work, reconnect the cable connector and repeat the failing operation.

Chapter 4

Memory check

Memory errors might stop system operations, show error messages on the screen, or hang the system.

1.

Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.

2.

Go to the diagnostic memory in the test items.

3.

Press F2 in the test items.

4.


NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.

Power System Check

To verify the symptom of the problem, power on the computer using each of the following power sources:

1.

Remove the battery pack.

2.

Connect the power adapter and check that power is supplied.

3.

Disconnect the power adapter and install the charged battery pack; then check that power is supplied by the battery pack.

If you suspect a power problem, see the appropriate power supply check in the following list:

T

“Check the Power Adapter” on page 59

T

“Check the Battery Pack” on page 59

Check the Power Adapter

Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power adapter cable. See the following figure

Pin 1: +19 to +20.5V

Pin 2: 0V, Ground

1.

If the voltage is not correct, replace the power adapter.

2.

If the voltage is within the range, do the following:

T

T

Replace the System board.

If the problem is not corrected, see “Undetermined Problems” on page 73.

T

If the voltage is not correct, go to the next step.

NOTE: An audible noise from the power adapter does not always indicate a defect.

3.

If the power-on indicator does not light up, check the power cord of the power adapter for correct continuity and installation.

4.

If the operational charge does not work, see “Check the Battery Pack” on page 59.

Check the Battery Pack

To check the battery pack, do the following:

From Software:

1.

Check out the Power Management in control Panel

2.

In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total

Battery Power Remaining are correct.

3.

Repeat the steps 1 and 2, for both battery and adapter.

Chapter 4 59

4.

This helps you identify first the problem is on recharging or discharging.

From Hardware:

1.

Power off the computer.

2.

Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the following figure

3.

If the voltage is still less than 7.5 Vdc after recharging, replace the battery.

To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer.

If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.

Re-install the battery pack.

If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light up, replace the DC/DC charger board.

Touchpad Check

If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a non-defective FRU:

1.

Reconnect the touchpad cables.

2.

Replace the touchpad.

3.

Replace the system board.

After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware problem. No service actions are necessary if the pointer movement stops in a short period of time.

60 Chapter 4

Power-on Self-Test Error Messages

The POST error message index lists the error message and their possible causes. The most likely cause is listed first.

NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU.

This index can also help you determine the next possible FRU to be replaced when servicing a computer.

If the symptom is not listed, see “Undetermined Problems” on page 73.

The following lists the error messages that the BIOS displays on the screen and the error symptoms classified by function.

NOTE: Most of the error messages occur during POST. Some of them display information about a hardware device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the way it has been configured.

NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter

Setup and install Setup defaults or correct the error.

Chapter 4 61

Index of Error Messages

Error Code List

Error Codes

006

010

070

071

072

110

<No error code>

<No error code>

Error Messages

Equipment Configuration Error

Causes:

1. CPU BIOS Update Code Mismatch

2. IDE Primary Channel Master Drive Error

(THe causes will be shown before “Equipment Configuration

Error”)

Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)

Real Time Clock Error

CMOS Battery Bad

CMOS Checksum Error

System disabled.

Incorrect password is specified.

Battery critical LOW

In this situation BIOS will issue 4 short beeps then shut down system, no message will show.

Thermal critical High

In this situation BIOS will shut down system, not show message.

Error Message List

Error Messages

Failure Fixed Disk

Stuck Key

Keyboard error

Keyboard Controller Failed

Keyboard locked - Unlock key switch

FRU/Action in Sequence

Reconnect hard disk drive connector.

“Load Default Settings” in BIOS Setup Utility.

Hard disk drive

System board

see “Keyboard or Auxiliary Input Device Check” on page 58. see “Keyboard or Auxiliary Input Device Check” on page 58. see “Keyboard or Auxiliary Input Device Check” on page 58.

Unlock external keyboard

Monitor type does not match CMOS - Run Setup Run “Load Default Settings” in BIOS Setup Utility.

Shadow RAM Failed at offset: nnnn BIOS ROM

System board

System RAM Failed at offset: nnnn

Extended RAM Failed at offset: nnnn

DIMM

System board

DIMM

System board

System battery is dead - Replace and run Setup Replace RTC battery and Run BIOS Setup Utility to reconfigure system time, then reboot system.

System CMOS checksum bad - Default configuration used

RTC battery

Run BIOS Setup Utility to reconfigure system time, then reboot system.

System timer error RTC battery


System board

62 Chapter 4


CMOS

Error Messages

Real time clock error

Previous boot incomplete - Default configuration used

Memory size found by POST differed from

Diskette drive A error

Incorrect Drive A type - run SETUP

System cache error - Cache disabled

CPU ID:

DMA Test Failed

Software NMI Failed

Fail-Safe Timer NMI Failed

Device Address Conflict

Allocation Error for device

Failing Bits: nnnn

Fixed Disk n

Invalid System Configuration Data

I/O device IRQ conflict

Operating system not found


RTC battery


System board

Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board


DIMM

System board

Check the drive is defined with the proper diskette type in BIOS

Setup Utility

See “External Diskette Drive Check” on page 58.

Check the drive is defined with the proper diskette type in BIOS

Setup Utility

System board

System board

DIMM

System board

DIMM

System board

DIMM

System board


RTC battery

System board


RTC battery

System board

DIMM

BIOS ROM

System board

None

BIOS ROM

System board


RTC battery

System board

Enter Setup and see if fixed disk and drive A: are properly identified.

Diskette drive

Hard disk drive

System board

Chapter 4 63

64


No beep, power-on indicator turns off and LCD is blank.

No beep Error Messages

No beep, power-on indicator turns on and LCD is blank.

No beep, power-on indicator turns on and LCD is blank. But you can see POST on an external

CRT.


Power source (battery pack and power adapter). See “Power

System Check” on page 59.

Ensure every connector is connected tightly and correctly.

Reconnect the DIMM.

LED board.

System board.



Reconnect the LCD connector

Hard disk drive

LCD inverter ID

LCD cable

LCD Inverter

LCD

System board

Reconnect the LCD connectors

LCD inverter ID

LCD cable

LCD inverter

LCD

System board

No beep, power-on indicator turns on and a blinking cursor shown on LCD during POST.

Ensure every connector is connected tightly and correctly

System board

No beep during POST but system runs correctly. Speaker

System board

Chapter 4

Phoenix BIOS Beep Codes

Code Beeps

28h

29h

2Ah

2Ch

2Eh

20h

22h

24h

26h

17h

18h

1Ah

1Ch

12h

13h

14h

16h

08h

09h

0Ah

0Bh

02h

03h

04h

06h

0Ch

0Eh

0Fh

10h

11h

2Fh

30h

3Ch

3Dh

42h

45h

46h

32h

33h

36h

38h

3Ah

Chapter 4

1-2-2-3

1-3-1-1

1-3-1-3

1-3-4-1

1-3-4-3

1-4-1-1

2-1-2-3

POST Routine Description

Verify Real Mode

Disable Non-Maskable Interrupt (NMI)

Get CPU type

Initialize system hardware

Initialize chipset with initial POST values

Set IN POST flag

Initialize CPU registers

Enable CPU cache

Initialize caches to initial POST values

Initialize I/O component

Initialize the local bus IDE

Initialize Power Management

Load alternate registers with initial POST values

Restore CPU control word during warm boot

Initialize PCI Bus Mastering devices

Initialize keyboard controller

BIOS ROM checksum

Initialize cache before memory autosize

8254 timer initialization

8237 DMA controller initialization

Reset Programmable Interrupt Controller

Test DRAM refresh

Test 8742 Keyboard Controller

Set ES segment register to 4 GB

Enable A20 line

Autosize DRAM

Initialize POST Memory Manager

Clear 215 KB base RAM

RAM failure on address line xxxx

RAM failure on data bits xxxx of low byte of memory bus

Enable cache before system BIOS shadow

RAM failure on data bits xxxx of high byte of memory bus

Test CPU bus-clock frequency

Initialize Phoenix Dispatch Manager

Warm start shut down

Shadow system BIOS ROM

Autosize cache

Advanced configuration of chipset registers

Load alternate registers with CMOS values

Initialize interrupt vectors

POST device initialization

Check ROM copyright notice

65

66

7Eh

80h

81h

82h

70h

72h

76h

7Ch

83h

84h

85h

86h

87h

88h

89h

8Ah

8Bh

8Ch

5Ah

5Bh

5Ch

60h

52h

54h

58h

59h

4Ch

4Eh

50h

51h

48h

49h

4Ah

4Bh

68h

69h

6Ah

6Bh

62h

64h

66h

67h

6Ch

6Eh

Code

2-2-3-1

Beeps POST Routine Description

Check video configuration against CMOS

Initialize PCI bus and devices

Initialize all video adapters in system

QuietBoot start (optional)

Shadow video BIOS ROM

Display BIOS copyright notice

Display CPU type and speed

Initialize EISA board

Test keyboard

Set key click if enabled

Test for unexpected interrupts

Initialize POST display service

Display prompt “Press F2 to enter SETUP”

Disable CPU cache

Test RAM between 512 and 640 KB

Test extended memory

Test extended memory address lines

Jump to User Patch1

Configure advanced cache registers

Initialize Multi Processor APIC

Enable external and CPU caches

Setup System Management Mode (SMM) area

Display external L2 cache size

Load custom defaults (optional)

Display shadow-area message

Display possible high address for UMB recovery

Display error messages

Check for configuration errors

Check for keyboard errors

Set up hardware interrupt vectors

Initialize coprocessor if present

Disable onboard Super I/O ports and IRQs

Late POST device initialization

Detect and install external RS232 ports

Configure non-MCD IDE controllers

Detect and install external parallel ports

Initialize PC-compatible PnP ISA devices

Re-initialize onboard I/O ports

Configure Motherboard Configurable Devices

(optional)

Initialize BIOS Area

Enable Non-Maskable Interrupts (NMIs)

Initialize Extended BIOS Data Area

Test and initialize PS/2 mouse

Initialize floppy controller

Chapter 4

C3h

C4h

C5h

C6h

BFh

C0h

C1h

C2h

C7h

C8h

C9h

D2h

B5h

B6h

B9h

BAh

BBh

BCh

BDh

BEh

A4h

A8h

AAh

ACh

AEh

B0h

B2h

B4h

9Eh

9Fh

A0h

A2h

99h

9Ah

9Ch

9Dh

93h

95h

96h

97h

98h

8Fh

90h

91h

92h

Chapter 4

Code

1-2

1


Determine number of ATA drives (optional)

Initialize hard-disk controllers

Initialize local-bus hard-disk controllers

Jump to UserPatch2

Build MPTABLE for multi-processor boards

Install CD ROM for boot

Clear huge ES segment register

Fixup Multi Processor table

Search for option ROMs. One long, two short beeps on checksum failure.

Check for SMART drive (optional)

Shadow option ROMs

Set up Power Management

Initialize security engine (optional)

Enable hardware interrupts

Determine number of ATA and SCSI drives

Set time of day

Check key lock

Initialize Typematic rate

Erase F2 prompt

Scan for F2 key stroke

Enter SETUP

Clear Boot flag

Check for errors

POST done- prepare to boot operating system

One short beep before boot

Terminate QuietBoot (optional)

Check password (optional)

Prepare Boot

Initialize DMI parameters

Initialize PnP Option ROMs

Clear parity checkers

Display MultiBoot menu

Clear screen (optional)

Check virus and backup reminders

Try to boot with INT 19

Initialize POST Error Manager (PEM)

Initialize error logging

Initialize error display function

Initialize system error handler

PnPnd dual CMOS (optional)

Initialize notebook docking (optional)

Initialize notebook docking late

Force check (optional)

Extended checksum (optional)

Unknown interrupt

67

68

E8h

E9h

EAh

EBh

ECh

EDh

EEh

EFh

E4h

E5h

E6h

E7h

E0h

E1h

E2h

E3h

F4h

F5h

F6h

F7h

F0h

F1h

F2h

F3h

Code

1


Initialize the chipset

Initialize the bridge

Initialize the CPU

Initialize the system timer

Initialize system I/O

Check force recovery boot

Checksum BIOS ROM

Go to BIOS

Set Huge Segment

Initialize Multi Processor

Initialize OEM special code

Initialize PIC and DMA

Initialize Memory type

Initialize Memory size

Shadow Boot Block

System memory test

Initialize interrupt vectors

Initialize Run Time Clock

Initialize video

Initialize System Management Mode

Output one beep before boot

Boot to Mini DOS

Clear Huge Segment

Boot to Full DOS

Chapter 4

Index of Symptom-to-FRU Error Message

LCD-Related Symptoms

Symptom / Error

LCD backlight doesn't work

LCD is too dark

LCD brightness cannot be adjusted

LCD contrast cannot be adjusted

Unreadable LCD screen

Missing pels in characters

Abnormal screen

Wrong color displayed

LCD has extra horizontal or vertical lines displayed.

Action in Sequence

Enter BIOS Utility to execute “Load Setup Default Settings”, then reboot system.

Reconnect the LCD connectors.

Keyboard (if contrast and brightness function key doesn't work).

LCD inverter ID

LCD cable

LCD inverter

LCD

System board

Reconnect the LCD connector

LCD inverter ID

LCD cable

LCD inverter

LCD

System board

LCD inverter ID

LCD inverter

LCD cable

LCD

System board

Indicator-Related Symptoms

Symptom / Error

Indicator incorrectly remains off or on, but system runs correctly


Reconnect the inverter board

Inverter board

System board

Power-Related Symptoms

Symptom / Error

Power shuts down during operation

The system doesn’t power-on.

The system doesn’t power-off.

Battery can’t be charged




Battery pack

Power adapter

Hard drive & battery connection board

System board



Battery pack

Power adapter

Hard drive & battery connection board

System board



Hold and press the power switch for more than 4 seconds.

System board

See “Check the Battery Pack” on page 59.

Battery pack

System board

Chapter 4 69

70

PCMCIA-Related Symptoms

Symptom / Error

System cannot detect the PC Card (PCMCIA) PCMCIA slot assembly

System board

PCMCIA slot assembly


PCMCIA slot pin is damaged.

Memory-Related Symptoms

Symptom / Error

Memory count (size) appears different from actual size.


Enter BIOS Setup Utility to execute “Load Default Settings, then reboot system.

DIMM

System board

Speaker-Related Symptoms

Symptom / Error

In Windows, multimedia programs, no sound comes from the computer.

Audio driver

Speaker

System board

Internal speakers make noise or emit no sound.

Speaker

System board


Power Management-Related Symptoms

Symptom / Error

The system will not enter hibernation

The system doesn't enter hibernation mode and four short beeps every minute.

The system doesn’t enter standby mode after closing the LCD

The system doesn't resume from hibernation mode.

The system doesn't resume from standby mode after opening the LCD.

Battery fuel gauge in Windows doesn’t go higher than 90%.


Keyboard (if control is from the keyboard)

Hard disk drive

System board

See “Sleeping State (S4)” on page 28.

Press Fn+

o

and see if the computer enters hibernation mode.

Touchpad

Keyboard

Hard disk connection board

Hard disk drive

System board


LCD cover switch

System board



Hard disk drive

System board


LCD cover switch

System board

Remove battery pack and let it cool for 2 hours

Refresh battery (continue use battery until power off, then charge battery)

Battery pack

System board

Chapter 4

Power Management-Related Symptoms

Symptom / Error

System hangs intermittently.


Reconnect hard disk/CD-ROM drives.


System board

Peripheral-Related Symptoms

Symptom / Error

System configuration does not match the installed devices.

External display does not work correctly.

USB does not work correctly

Print problems.

Serial or parallel port device problems.


Enter BIOS Setup Utility to execute “Load Default Settings”, then reboot system.

Reconnect hard disk/CD-ROM/diskette drives.

Press Fn+F5, LCD/CRT/Both display switching

System board

System board

Ensure the “Parallel Port” in the “Onboard Devices Configuration” of

BIOS Setup Utility is set to Enabled.

Onboard Devices Configuration

Run printer self-test.

Printer driver

Printer cable

Printer

System Board

Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup

Utility is set to Enabled.

Device driver

Device cable

Device

System board

Keyboard/Touchpad-Related Symptoms

Symptom / Error

Keyboard (one or more keys) does not work.

Touchpad does not work.


Reconnect the keyboard cable.

Keyboard

System board

Reconnect touchpad cable.

Touchpad board

System board

Modem-Related Symptoms

Symptom / Error

Internal modem does not work correctly.

Modem phone port modem combo board

System board


NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined

Problems” on page 73.

Chapter 4 71

Intermittent Problems

Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists.

When analyzing an intermittent problem, do the following:

1.

Run the advanced diagnostic test for the system board in loop mode at least 10 times.

2.

If no error is detected, do not replace any FRU.

3.

If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.

72 Chapter 4

Undetermined Problems

The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative.

Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).

NOTE: Verify that all attached devices are supported by the computer.

NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power

System Check” on page 59):

1.

Power-off the computer.

2.

Visually check them for damage. If any problems are found, replace the FRU.

3.

Remove or disconnect all of the following devices:

T

Non-Acer devices

T

T

T

T

Printer, mouse, and other external devices

Battery pack

Hard disk drive

DIMM

T

T

CD-ROM/Diskette drive Module

PC Cards

4.

Power-on the computer.

5.

Determine if the problem has changed.

6.

If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.

7.

If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:

T

T

System board

LCD assembly

Chapter 4 73

74 Chapter 4

Jumper and Connector Locations

Mainboard Layout

Top View

Chapter 5

3

4

1

2

5

FAN1

LCD1

SKT1

SKT2

U22 or

PCH1?

?)

Fan Connector

LCD Cable Connector

IEEE 1394 Connector

USB Port

PC Card Slot

Chapter 5

8

9

6

7

10

CARD1

RTC1

BT1

TPAD1

KB1

5-in-1 Card Reader Slot

RTC Battery Connector

Bluetooth Module Connector

Touchpad FFC Connector

Keyboard Connector

75

Bottom View

76

5

6

7

3

4

1

2

8

9

19

JK1

DCIN1

CRT1

DOCK

1

U27

WIN1

U32

U31

BAT1

U41

Giga LAN Port

Power Jack

VGA Port ezDock Port

IO Controller-PC 87392

Wireless LAN Card Slot

Keyboard Controller

LAN Controller-BROADCOM BCM5788M

Battery Connector

Power Generator-IDT CV125PA

14

15

16

10

11

12

13

17

18

IOB1

HDD1

DM2

DM1

U44

SW8

U52

U34

U33

Main Board to IO Board Connector

HDD Connector

DIMM Slot

DIMM Slot

South Bridge-Intel ICH6-M

Switch

Cardbus/1394/Card Reader Controller-

UltraMedia PCI 7411

North Bridge

CPU

Chapter 5

IO Board Layout

Top View

3

4

1

2

5

6

INTMIC1

LID1

U1

BTB1

SPKR1

LOUT1

Microphone Connector

Cover Switch Cable Connector

Audio Codec-Realtek ALC655

IO Board to Main Board Connector

Speaker Set Connector

Line-out Port

7

8

9

10

11

12

MIC1

LINT1

USB1

USB2

U6

JK1

Microphone-in Port

Line-in Port

USB Port

USB Port

FIR

RJ11 Modem Jack

Chapter 5 77

Bottom View

78

1 MDC1 Modem Board Connector 2 RING1 MDC Cable Connector

Chapter 5

Switch Settings

Please see the bottom view of the main board layout for switch location. The image bleow is switch enlarged image.

Switch Settings

Switch

SW8-1

SW8-2

SW8-3

SW8-4

Function

Clear Password

Bootblock

Keyboard Matrix ID1

Keyboard Matrix ID2

Chapter 5 79

80 Chapter 5

Chapter 6

FRU (Field Replaceable Unit) List

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 3300/

Extensa 3100. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise

Authorization).

Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel.

For whatever reasons a part number change is made, it will not be noted on the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You

MUST use the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.

Chapter 6 81

Exploded Diagram

82

ADAPTER

Image Part Name Description

ADAPTER 65W

LITEON PA-1650-

02WR

ADAPTER 65W LISHIN

SLS0335A19A54LF

ADT 65W LITEON PA-

1650-02WR

ADT 65W LISHIN

SLS0335A19A54LF

Acer P/N

AP.06503.011

AP.06506.003

BATTERY

BATTERY PACK LI+

6CELL 2.4MAH SONY

BTY PACK LI+ 6C

2.4AH SONY

BT.00604.005

Chapter 6

BOARD

Image Part Name

BATTERY PACK LI+

6CELL 2.4MAH SANYO

BATTERY PACK LI+

9CELL 2.4MAH SANYO

Description

BTY PACK LI+ 6C

2.4AH SANYO

BTY PACK LI+ 9C

2.4AH SANYO

MODEM BOARD

FOXCONN

T60M845.01

MODEM MDC1.5

(AC97) T60M845.01

Acer P/N

BT.00603.012

BT.00903.004

54.A56V1.001

TOUCHPAD BOARD

SYNAPTIC TM51-389

TOUCHPAD

SYNAPTICS TM51-389

56.TB1V1.001

WIRELESS LAN

BOARD 802.11BG

INTEL

WLAN 802.11BG

INTEL867074 LF

KI.CAX01.013

BLUETOOTH BOARD

FOXCONN BCM2045

BT MODULE

FOXCONN BCM2045

54.A74V1.003

I/O BOARD MYNA2 I/O BD 05519-

SB (DIP)

55.TB1V1.001

CABLE

83

84

Image Part Name

MODEM CABLE

Description

CABLE MODEM US W/

RECYCLE

Acer P/N

50.TB1V1.002

TOUCHPAD CABLE C.A. T/P FFC JH

MYNA2

50.TB1V1.003

POWER CODE 5A

250V 3P UK BK

POWER CORD 2.5A

125V USA

BLYETOOTH CABLE

CODE 5A 250V 3P UK

BK

CORD USA/W CNS

2.5A 125V 8121-

B/T CABLE HT MYNA-2

27.03118.001

27.01518.781

50.TB1V1.010

CASE/COVER/BRACKET ASSEMBLY

PCMCIA DUMMY

CARD

CARD-BUS DUMMY

CARD

42.TB1V1.003

SD MEMORY DUMMY

CARD

SD DUMMY CARD

MYNA2

42.TB1V1.004

UPPER CASE UPPER-CASE ASSY

Note: This is engineering sample, and the color of the upper case is not correct.

60.TB1V1.002

Chapter 6

Image Part Name

TOUCHPAD PLATE

Description

ASSY T/P PLATE

MYNA2

Acer P/N

33.TB1V1.001

LOWER CASE ASSY L-CASE FOR

CARD BUS MYNA2

60.TB1V1.001

SPEAKER LEFT/

RIGHT

SPEAKER MYNA-2 23.TB1V1.001

MICROPHONE MICROPHONE

MYNA2

23.TB1V1.002

COVER SWITCH

CABLE

FRONT COVER

C.A. COVER SWITCH

MYNA2

ASSY FRONT COVER

MYNA2

50.TB1V1.001

60.TB1V1.004

MIDDLE COVER ASSY MIDDLE COVER

MYNA2

60.TB1V1.003

85

86

Image Part Name

HDD COVER

Description

ASSY HDD COVER

MYNA2

Acer P/N

42.TB1V1.001

MINI PCI COVER ASSY MINIPCI COVER

MYNA-2

42.TB1V1.002

COMBO MODULE

COMBO 24X

PANASONIC UJDA770

COMBO 24X PAC/

UJDA770 MYNA EXT

KO.02406.014

COMMUNICATION MODULE

COMBO 24X LITEON

SOSC-2483K

COMBO LIT/SOSC-

2483K LF EXT

WIRELESS ANTENNA

LEFT/RIGHT

ANTENNA CABLE

MYNA2

KO.02409.014

25.TB1V1.001

DVD MODULE

DVD-RW DRIVE 8X

LITEON SOSW-833S

DUAL

DUAL 8X LTN/SOSW-

833S MYNA EXT

KU.00804.020

Chapter 6

FAN

Image Part Name

DVD-RW DRIVE 8X

PANASONIC UJ-840B

DUAL

Description

DUAL PAN/UJ-840B LF

8X DVD

Acer P/N

KU.00807.030

FAN FAN FORCECON

MORAR

23.A74V1.001

HDD MODULE

HDD MODULE 40G

HDD MYLAR W/

CUPPER

HDD MODULE 40G

ASSY HDD CHASSIS

MYNA-2

TBD

33.TB1V1.002

HDD 40G HITACHI

HTS421240H9AT00

HDD 40G TOSHIBA

MK4025GAS

HDD 40G SEAGATE

ST9402113A

HDD MODULE 60G

HDD MYLAR W/

CUPPER

HDD 60G HITACHI

HTS421260H9AT00

HDD 60G TOSHIBA

MK6025GAS

HDD 60G SEAGATE

ST960812A

HDD MODULE 80G

HDD MYLAR W/

CUPPER

HDD 80G TOSHIBA

MK8025GAS

HDD 80G HITACHI

HTS421280H9AT00

HDD 80G SEAGATE

ST980829A

HDD MODULE 100G

HDD 40GB HGST

HTS421240H9AT00

HDD 40GB TOSHIBA

MK4025GAS

HDD 40GB SEAGATE

ST9402113A

ASSY HDD 60G

SEAGATE MYNA-2

ASSY HDD CHASSIS

MYNA-2

HDD 60GB HGST

HTS421260H9AT00

HDD 60GB TOSHIBA

MK6025GAS

HDD 60GB SEAGATE

ST960812A

ASSY HDD 80G HGST

MYNA-2

ASSY HDD CHASSIS

MYNA-2

HDD 80GB TOSHIBA

MK8025GAS

HDD 80GB HGST

HTS421280H9AT00

HDD 80GB SEAGATE

ST980829A

ASSY HDD 100G

HGST MYNA-2

KH.04007.013

KH.04004.005

KH.04001.016

TBD

33.TB1V1.002

KH.06007.009

KH.06004.004

KH.06001.003

TBD

33.TB1V1.002

KH.08004.003

KH.08007.011

KH.08001.013

TBD

87

88

KEYBOARD

Image Part Name

HDD MYLAR W/

CUPPER

HDD 100G HITACHI

HTS421210H9AT00

HDD 100G TOSHIBA

MK1031GAS

HDD 100GB SEAGATE

ST9100825A

Description

ASSY HDD CHASSIS

MYNA-2

HDD 100GB HGST

HTS421210H9AT00

HDD 100GB TOSHIBA

MK1031GAS

HDD 100GB SEAGATE

ST9100825A

Acer P/N

33.TB1V1.002

KH.10007.002

KH.10004.001

KH.10001.003

KEYBOARD 88KEY

DARFON NSK-AEN1D

US-INT

KB DARFON NSK-

AEN1D US-INT 88K

KB.TB107.001

KEYBOARD DARFON

NSK-AEN02 CHINESE

88

TM3300 KEYBOARD

SPANISH

TM3300 KEYBOARD

THAI

TM3300 KEYBOARD

BRAZILIAN

PROTUGESE

TM3300 KEYBOARD

KOREA

TM3300 KEYBOARD

UK

TM3300 KEYBOARD

GERMAN

TM3300 KEYBOARD

ITALIAN

TM3300 KEYBOARD

FRENCH

TM3300 KEYBOARD

SWISS/G

TM3300 KEYBOARD

PORTUGUESE

TM3300 KEYBOARD

ARABIC

TM3300 KEYBOARD

BELGIUM

TM3300 KEYBOARD

SWEDEN

TM3300 KEYBOARD

CZECH

TM3300 KEYBOARD

HUNGAIAN

TM3300 KEYBOARD

NORWAY

KB DARFON NSK-

AEN02 CHINESE 88

TM3300 KEYBOARD

SPANISH

TM3300 KEYBOARD

THAI

TM3300 KEYBOARD

BRAZILIAN

PROTUGESE

TM3300 KEYBOARD

KOREA

TM3300 KEYBOARD

UK

TM3300 KEYBOARD

GERMAN

TM3300 KEYBOARD

ITALIAN

TM3300 KEYBOARD

FRENCH

TM3300 KEYBOARD

SWISS/G

TM3300 KEYBOARD

PORTUGUESE

TM3300 KEYBOARD

ARABIC

TM3300 KEYBOARD

BELGIUM

TM3300 KEYBOARD

SWEDEN

TM3300 KEYBOARD

CZECH

TM3300 KEYBOARD

HUNGAIAN

TM3300 KEYBOARD

NORWAY

KB.TB107.002

KB.TB107.003

KB.TB107.004

KB.TB107.005

KB.TB107.006

KB.TB107.007

KB.TB107.008

KB.TB107.009

KB.TB107.010

KB.TB107.011

KB.TB107.012

KB.TB107.013

KB.TB107.014

KB.TB107.015

KB.TB107.016

KB.TB107.017

KB.TB107.018

Chapter 6

Image

LCD MODULE

Part Name

TM3300 KEYBOARD

DANISH

TM3300 KEYBOARD

TURKISH

TM3300 KEYBOARD

TURKISH F TYPE

TM3300 KEYBOARD

CANADIAN FRENCH

TM3300 KEYBOARD

JAPANESE

TM3300 KEYBOARD

GREEK

TM3300 KEYBOARD

HEBREW

TM3300 KEYBOARD

RUSSIAN

TM3300 KEYBOARD

SLOVENIA (SLO)

TM3300 KEYBOARD

CROATIA (CR )

LCD MODULE 14.1"

WXGA GLARE 400G

INVERTER BOARD

DARFON

Description

TM3300 KEYBOARD

DANISH

TM3300 KEYBOARD

TURKISH

TM3300 KEYBOARD

TURKISH F TYPE

TM3300 KEYBOARD

CANADIAN FRENCH

TM3300 KEYBOARD

JAPANESE

TM3300 KEYBOARD

GREEK

TM3300 KEYBOARD

HEBREW

TM3300 KEYBOARD

RUSSIAN

TM3300 KEYBOARD

SLOVENIA (SLO)

TM3300 KEYBOARD

CROATIA (CR )

LCD 14" WXGA

QD14TL02-04

INVERTER 17" ROHS

VK.21189.401

Acer P/N

KB.TB107.019

KB.TB107.020

KB.TB107.021

KB.TB107.022

KB.TB107.023

KB.TB107.024

KB.TB107.025

KB.TB107.026

KB.TB107.027

KB.TB107.28

6M.TB1V1.001

19.TB1V1.001

LCD CABLE 14.1 "

WXGA

CABLE 14.1" WXGA HT

MYNA2

50.TB1V1.004

LCD BRACKET RIGHT BRKT LCD 14.1" R

MYNA2

33.TB1V1.003

89

90

Image Part Name

LCD BRACKET LEFT

Description

BRKT LCD 14.1" L

MYNA2

Acer P/N

33.TB1V1.004

LCD BEZEL 14.1" ASSY LCD 14.1"

BEZEL MYNA-2

60.TB1V1.005

LCD BEZEL 14.1”

LCD PANEL 14.1"

ASSY LCD 14.1"

BEZEL MYNA-2 (for

Extensa 3100) with model name printing on it

ASSY LCD 14.1"

PANEL MYNA-2

60.E31V1.001

(this is different item from TravelMate 3300)

60.TB1V1.006

HINGE PACK LEFT/

RIGHT

HINGE PACK LEFT/

RIGHT

LCD 14.1" WXGA

N141I1-L05 GLARE

400G

LCD 14" WXGA

N141I1-L05

6K.TB1V1.001

LK.1410D.006

LCD 14.1" WXGA QDI

QD14TL02-04 400G

LCD MODULE 14.1"

WXGA GLARE 420G

INVERTER BOARD

DARFON

LCD CABLE 14.1 "

WXGA

LCD 14" WXGA

QD14TL02-04

LCD 14.1" WXGA

N141C1-L02

INVERTER 17" ROHS

VK.21189.401

CABLE 14.1" WXGA HT

MYNA2

LK.14109.006

6M.TB1V1.002

19.TB1V1.001

50.TB1V1.004

Chapter 6

Image Part Name

LCD BRACKET RIGHT

LCD BRACKET LEFT

LCD BEZEL 14.1"

LCD PANEL 14.1"

HINGE PACK LEFT/

RIGHT

LCD 14.1" WXGA

N141C1-L02 GLARE

420G

LCD MODULE 14.1"

WXGA NONE GLARE

400G

INVERTER BOARD

DARFON

LCD CABLE 14.1 "

WXGA

LCD BRACKET RIGHT

LCD BRACKET LEFT

LCD BEZEL 14.1"

LCD PANEL 14.1"

HINGE PACK LEFT/

RIGHT

LCD 14.1" WXGA

N141I1-L07 NONE

GLARE 400G

LCD 14.1" WXGA QDI

QD14TL02-03 NONE

GLARE 400G

LCD MODULE 14.1"

WXGA NONE GLARE

420G

INVERTER BOARD

DARFON

LCD CABLE 14.1 "

WXGA

LCD BRACKET RIGHT

LCD BRACKET LEFT

LCD BEZEL 14.1"

LCD PANEL 14.1"

HINGE PACK LEFT/

RIGHT

Description

BRKT LCD 14.1" R

MYNA2

BRKT LCD 14.1" L

MYNA2

ASSY LCD 14.1"

BEZEL MYNA-2

ASSY LCD 14.1"

PANEL MYNA-2

HINGE PACK LEFT/

RIGHT

LCD 14.1" WXGA

N141C1-L02

Acer P/N

33.TB1V1.003

33.TB1V1.004

60.TB1V1.005

60.TB1V1.006

6K.TB1V1.001

LK.1410D.008

ASSY QDI 14.1" WXGA

(N-GLAR

6M.TB1V1.003

INVERTER 17" ROHS

VK.21189.401

CABLE 14.1" WXGA HT

MYNA2

BRKT LCD 14.1" R

MYNA2

BRKT LCD 14.1" L

MYNA2

ASSY LCD 14.1"

BEZEL MYNA-2

ASSY LCD 14.1"

PANEL MYNA-2

HINGE PACK LEFT/

RIGHT

LCD 14.1" WXGA

N141I1-L07

19.TB1V1.001

50.TB1V1.004

33.TB1V1.003

33.TB1V1.004

60.TB1V1.005

60.TB1V1.006

6K.TB1V1.001

LK.1410D.007

LCD 14" WXGA

QD14TL02-03

LCD MODULE 14.1"

WXGA

LK.14109.007

6M.TB1V1.004

INVERTER 17" ROHS

VK.21189.401

CABLE 14.1" WXGA HT

MYNA2

BRKT LCD 14.1" R

MYNA2

BRKT LCD 14.1" L

MYNA2

ASSY LCD 14.1"

BEZEL MYNA-2

ASSY LCD 14.1"

PANEL MYNA-2

HINGE PACK LEFT/

RIGHT

19.TB1V1.001

50.TB1V1.004

33.TB1V1.003

33.TB1V1.004

60.TB1V1.005

60.TB1V1.006

6K.TB1V1.001

91

92

Image

MAIN BOARD

Part Name

LCD 14.1" WXGA

N141C1-L03 NONE

GLARE 420G

LCD 14.1" WXGA QDI

QD14TL01-02 NONE

GLARE 420G

LCD 14.1" WXGA QDI

QD14TL01-03 NONE

GLARE 420G

Description

LCD 14.1" WXGA

N141C1-L03

LCD 14.1" WXGA

QD14TL01-02

LCD 14" WXGA

QDIQD14TL01-03

Acer P/N

LK.1410D.009

LK.14109.005

LK.14109.004

MAINBOARD MYNA 2

1.4G

1.73

MHZ(CPU ON

BOARD) W/CPU

HEATSINK & PCMCIA

SLOT & RTC BATTERY

MAINBOARD MYNA 2

2.13GMHZ(CPU ON

BOARD) W/CPU

HEATSINK & PCMCIA

SLOT & RTC BATTERY

MAINBOARD MYNA 2

2.0GMHZ(CPU ON

BOARD) W/CPU

HEATSINK & PCMCIA

SLOT & RTC BATTERY

RTC BATTERY LI

MB PM740 MYNA2 W/

O DIMM

MYNA2 MB DOT-2.13G

05216SB DIP

MYNA2 MB 2.0G

05216SB DIP

BATTERY RTC

CANARY

LB.TB101.008

LB.TB101.014

LB.TB101.012

23.T28V1.001

CPU HEATSINK W/O

FAN

ASSY CPU HEAT SINK

MYNA2

34.TB1V1.001

PCMCIA SLOT 4PIN

SDIMM 256M HYNIX

HYMP532S64P6-C4

CONN CARDBUS 4P

59330-00L0C

SODIMM 256M

HYMP532S64P6-C4

22.T28V1.001

KN.2560G.006

SDIMM 256M

INFINEON

HYS64T32000HDL-3.7-

A

SODIMM256MHYS64T

32000HDL-3.7-A

KN.25602.023

Chapter 6

Image Part Name

SDIMM 512M

INFINEON

MHYS64T64020HDL-

3.7-A

SDIMM SAMSUNG

M470T3354CZ3-CD5

SDIMM 512M NANYA

NT512T64UH8A1FN-

37B

SDIMM 512M

SAMSUNG

M470T6554CZ3-CD5

SDIMM 512M HYNIX

HYMP564S64P6-C4

LCD SCREW RUBBER

Description

SODIMM512MHYS64T

64020HDL-3.7-A

Samsung

M470T3354CZ3-CD5

SODIMM512M

NT512T64UH8A1FN-

37B

SODIMM 512M

M470T6554CZ3-CD5

SODIMM 512M

HYMP564S64P6-C4

RUB LCD RUBBER

CUSHION BOLSENA

Note: See the upper two rubber cushion.

Acer P/N

KN.51202.021

KN.2560B.016

KN.51203.023

KN.5120B.015

KN.5120G.005

47.A46V1.002

LCD SCREW RUBBER RUBBER SCREW

Note: See the lower two rubber

47.TB1V1.001

SCROLL KEY RUBBER KNOB SCROLL KEY

MYNA2

Note: The picture below shows its location. It is put on the touchpad plate.

47.TB1V1.002

LOGO PLATE FOR

BEZEL

LOGO PLATE FOR

PANEL

PLT BEZEL PLATE

"ACER " LOGO

PLT ACER LOGO

ADHESIVE T.M.

31.A46V1.001

31.T49V1.001

93

94

Image Part Name

HDD SPONGE

Description

HDD SPONGE MYNA-2

Acer P/N

47.TB1V1.003

SCREW

SCREW

SCREW

SCREW

SCREW

SCREW

SCREW

SCREW

SCREW

SCREW

SCREW

SCW HEX NYL I#R-40/

O#4-40 L5.9

SCREW MACH

WAFER M2*L4 NI

SCREW M2*L9 NYLOK

SCRW WH MS+CBZ

M2.5+L4 BLACK

SCREW M2.5-6

SCREW M2*3 NYLON

1JMCPC-420325

SCREW

M2.5*4L(NYLOCK)BLA

CK ZN

SCREW M2.5X6

SRW M2.5*8L B/ZN

NYLOK 700

SCREW M2-3

SCRW M2*4 WAFER

NI

34.4C210.001

86.T39V1.002

86.00D38.520

86.9A323.4R0

86.9A323.6R0

86.9A352.3R0

86.9A353.4R0

86.9A353.6R0

86.9A353.8R0

86.9A522.3R0

86.9A552.4R0

Chapter 6

No results