advertisement
Acer
TravelMate 8210/8200
Service Guide
Service guide files and updates are available on the ACER/CSD web. For more information, please refer to http:// csd.acer.com.tw
PRINTED IN TAIWAN
II
Revision History
Please refer to the table below for the updates of notebook TravelMate 8210/8200 service guide.
Date
October 12, 2006
Chapter Updates first release
Copyright
Copyright
©
2006 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.
III
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose.
Any Acer Incorporated software described in this manual is sold or licensed “as is”. Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.
Acer is a registered trademark of Acer Incorporated.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
IV
Conventions
The following conventions are used in this manual:
SCREEN MESSAGES Denotes actual messages that appear on screen.
NOTE
WARNING
CAUTION
IMPORTANT
Gives bits and pieces of additional information related to the current topic.
Alerts you to any damage that might result from doing or not doing specific actions.
Gives precautionary measures to avoid possible hardware or software problems.
Reminds you to do specific actions relevant to the accomplishment of procedures.
V
VI
Preface
Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's “global” product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details.
2. Please note WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reason, if a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.
Table of Contents
Chapter 1 System Specifications 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Display and Graphics . . . . . . . . . . . . . . . . . . . . . . . 1
Storage Subsystem . . . . . . . . . . . . . . . . . . . . . . . . 1
I/O Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Power Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Weight and Dimensions . . . . . . . . . . . . . . . . . . . . . 3
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 4
Outlook View . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Open View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Closed Front View . . . . . . . . . . . . . . . . . . . . . . . . . 6
Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using the Keyboard . . . . . . . . . . . . . . . . . . . . 10
Lock keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Embedded Numeric Keypad . . . . . . . . . . . . . . . . . 10
Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Easy-launch Buttons . . . . . . . . . . . . . . . . . . . . 15
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Touchpad Basics . . . . . . . . . . . . . . . . . . . . . . . . . 16
Acer Empowering Technology . . . . . . . . . . . . 17
Acer eDataSecurity Management . . . . . . . . . . . . . 18
Acer eLock Management . . . . . . . . . . . . . . . . . . . 20
Acer ePerformance Management . . . . . . . . . . . . . 21
Acer eRecovery Management . . . . . . . . . . . . . . . 22
Acer eNet Management . . . . . . . . . . . . . . . . . . . . 22
Acer ePower Management . . . . . . . . . . . . . . . . . . 24
Acer ePresentation Management . . . . . . . . . . . . . 25
TOC VIII
Acer OrbiCam . . . . . . . . . . . . . . . . . . . . . . . . . 26
Launching the Acer OrbiCam . . . . . . . . . . . . . . . . 27
Changing the Acer OrbiCam settings . . . . . . . . . . 27
Capturing photos or videos . . . . . . . . . . . . . . . . . . 29
Using the Acer OrbiCam as webcam . . . . . . . . . . 29
Enabling the Acer VisageON . . . . . . . . . . . . . . . . 29
Acer GraviSense . . . . . . . . . . . . . . . . . . . . . . 32
Using Acer GraviSense . . . . . . . . . . . . . . . . . . . . 32
Protecting the HDD . . . . . . . . . . . . . . . . . . . . . . . . 32
Anti-Theft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using the System Utilities . . . . . . . . . . . . . . . . 34
Acer GridVista (dual-display compatible) . . . . . . . 34
Launch Manager . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Hardware Specifications and Configurations . 36
Chapter 2 System Utilities 45
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . 45
Invoking BIOS Setup . . . . . . . . . . . . . . . . . . . . . . 45
Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Launch Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Power Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Lid Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Auto-Dim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Information Menu . . . . . . . . . . . . . . . . . . . . . . 48
Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Advanced Menu . . . . . . . . . . . . . . . . . . . . . . . 51
Security Menu . . . . . . . . . . . . . . . . . . . . . . . . . 52
Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Exit Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Chapter 3 Machine Disassembly and Replacement 56
General Information . . . . . . . . . . . . . . . . . . . . 56
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . 56
Disassembly Procedure Flowchart . . . . . . . . . 57
Disassembly Procedure . . . . . . . . . . . . . . . . . 59
IX TOC
Removing the Battery Pack . . . . . . . . . . . . . . . . . 59
Removing the HDD Module . . . . . . . . . . . . . . . . . 59
Removing the Memory and the MiniPCI Card . . . 60
Disassembling the Main Unit . . . . . . . . . . . . . . . . 61
Disassembling the LCD Module . . . . . . . . . . . . . . 67
Disassembling the ODD Module . . . . . . . . . . . . . . 69
Disassembling the CCD Module . . . . . . . . . . . . . . 70
Disassembling the HDD Module . . . . . . . . . . . . . . 70
Chapter 4 Troubleshooting 71
System Check Procedures . . . . . . . . . . . . . . . 72
External Diskette Drive Check . . . . . . . . . . . . . . . 72
External CD-ROM Drive Check . . . . . . . . . . . . . . 72
Keyboard or Auxiliary Input Device Check . . . . . . 72
Memory Check . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Power System Check . . . . . . . . . . . . . . . . . . . . . . 73
Check the Power Adaptor . . . . . . . . . . . . . . . . . . . 73
Check the Battery Pack . . . . . . . . . . . . . . . . . . . . 73
Touchpad Check . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Power-On Self-Test (POST) Error Message . 75
Index of Error Messages . . . . . . . . . . . . . . . . . . . . 75
POST Code . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Index of Symptom-to-FRU Error Message . . . 79
Intermittent Problems . . . . . . . . . . . . . . . . . . . 82
Undetermined Problems . . . . . . . . . . . . . . . . . 83
Chapter 5 Jumper and Connector Locations 84
Top View of Main Board . . . . . . . . . . . . . . . . . 84
Part One of Top View . . . . . . . . . . . . . . . . . . . . . . 85
Part Two of Top View . . . . . . . . . . . . . . . . . . . . . . 85
Part Three of Top View . . . . . . . . . . . . . . . . . . . . . 86
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Part One of Bottom View . . . . . . . . . . . . . . . . . . . 87
Part Two of Bottom View . . . . . . . . . . . . . . . . . . . 88
Part Three of Bottom View . . . . . . . . . . . . . . . . . . 88
Chapter 6 FRU (Field Replaceable Unit) List 89
Exploded Diagram . . . . . . . . . . . . . . . . . . . . . 90
TOC X
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
XI TOC
Chapter 1
System Specifications
Features
Operating System
•
Windows Vista TM Capable
•
Windows Vista
TM
Premium Ready
•
Genuine Windows
®
XP Professional x64 Edition
•
Genuine Windows
®
XP Professional (SP2)
•
Genuine Windows
®
XP Home Edition (SP2)
Platform
Intel
®
Centrino
®
Duo mobile technology, featuring:
•
Intel
®
Core
TM
Duo processor T2300/ T2400/ T2500/ T2600 (2MB L2 cache, 1.66/ 1.83/ 2.0/ 2.16GHz, 667
MHz FSB) (for TravelMate 8200 series)
•
Intel
®
Core
TM
2 Duo processor T5500/ T5600 (2MB L2 cache, 1.66/ 1.83GHz, 667MHz FSB), or T7200/
T7400/ T7600 (4MB L2 cache, 2/ 2.16/ 2.33GHz, 667MHz) (for TravelMate 8210 series)
•
Intel
®
945PM (Calistoga) Express Chipset with ICH7M-DH
System Memory
•
512MB/1GB or 2GB of DDR2 533/667MHz memory, upgradeable to 4GB using two soDIMM modules
(dual channel support)
Display and Graphics
•
15.4” WSXGA + TFT LCD, 1680 x 1050 pixel resolution, 16.7 million colors, simultaneous multi-window viewing via Acer GridVista TM support
•
ATI Mobility TM Radeon
®
X1600 with 256MB of GDDR3 VRAM, ATI POWERPLAY TM 5.0, Microsoft
®
DirectX
®
9.0 and PCI Express
® support
•
Dual View TM support
•
Simultaneous LCD and CRT display, with LCD panel resolution at 70Hz refresh rate
•
Up to 2048 x 1536 resolution on non-interlaced CRT display
•
MPEG-2/DVD hardware-assisted capability
•
S-video/TV-out (NTSC/PAL) support
•
DVI-D (true digital video interface) support
Storage Subsystem
•
80/100/120/160GB SATA hard disk drive with Acer DASP (Disk Anti-Shock Protection)
•
Acer MediaBay for hot-swappable optical drive modules
•
8X DVD-Super Multi double layer
•
1X Blue-Ray drive
•
5-in-1 card reader, Secure Digital (SD), MultimediaCard (MMC), Memory Stick
®
(MS), Memory Stick
PRO TM , (MS-PRO) and xD-Picture Card TM (xD)
Chapter 1 1
2
I/O Interface
•
124-pin Acer ezDock port
•
ExpressCard
TM
/34 slot
•
Four USB 2.0 ports
•
IEEE 1394 port
•
Ethernet (RJ-45) port
•
Modem (RJ-11) port
•
External display (VGA) port
•
S-video/TV-out (NTSC/PAL) port
•
DVI-D port
•
Microphone/line-in jack
•
Headphones/speaker/line-out with S/PDIF support
•
Fast infrared (FIR) port
•
PC Card slot (one Type II)
•
34 mm PCI Express Card slot
•
SmartCard slot
•
5-in-1 card reader (SD/MMC/MS/MS-Pro/xD-Picture Card
TM
)
•
DC-in jack for AC adaptor
Communication
•
Acer Video Conference featuring Acer Orbicam and optional Acer Bluetooth
®
VoIP phone
•
Acer Orbicam 1.3 megapixel CMOS camera (LCD panel-mounted) featuring:
•
225-degree ergonomic rotation
•
Acer VisageON technology
•
Acer PrimaLite technology
•
Modem: 56K ITU V.92 modem with PTT approval, Wake-on-Ring ready
•
LAN: Gigabit Ethernet, Intel
®
AMT (Active Management Technology) support; Wake-on-LAN support
•
WLAN: Integrated Intel
®
PRO/Wireless 3945 ABG network connection (dual-band tri-mode 802.11a/b/g)
Wi-Fi CERTIFIED
TM solution, Acer SignalUp
TM
wireless technology support
Power Subsystem
•
ACPI 2.0 CPU power management standard: Standby and Hibernation power-saving modes
•
87W 7800mAh 9-cell Li-Ion battery pack and optional 42W 3800mAh Li-Ion 2 nd battery pack
•
Acer QuicCharge
TM technology:
•
80% charge in 1 hour
•
2-hour rapid charge with system off
•
2.5-hour charge-in-use
•
Three-pin 90W AC adaptor
Audio
•
Intel
®
high-definition audio support
•
S/PDIF (Sony/Philips Digital Interface) support for digital sound system
•
Audio system with two built-in speakers (1.5W)
•
Built-in microphone
•
Sound Blaster
®
Pro and MS-Sound compatible
Chapter 1
Weight and Dimensions
•
3 kg (6.6 lbs.)
•
364 (W) x 271 (D) x 26.3/38 (H) mm (14.33 x 10.66 x 1.03/1.49 inches)
Chapter 1 3
Block Diagram
4 Chapter 1
Outlook View
Open View
Just for Starters...
8
9
10
6
7
4
5
2
3
#
1
#
Item
Display screen
Microphone
Palmrest
Camera
Easy-launch buttons
Power button
Status indicators
Keyboard
Touchpad
Click buttons (left, center and right)
Description
Description
Displays computer output, also called Liquid-Crystal Display (LCD).
Serves as an internal microphone for sound recording.
Serves to support your palms and wrists when you use the computer.
Captures photos and videos.
Buttons for launching frequently used programs.
Light-Emitting Diodes (LEDs) that light up to show the status of the computer's functions and components.
Serves to key in the data.
Touch-sensitive pointing device which functions like a computer mouse.
The left and right buttons function like the left and right mouse buttons; the center button serves as a four-way scroll button.
Chapter 1 5
6
# Item Description
"Launch keys" on page 10
# Icon Item
# Item
#
#
Item
# Item
Description
Description
Description
# Item
"Launch keys" on page 10
Description
"Launch keys" on page 10
# Item Description
"Easy-launch buttons" on page 10
Closed Front View
Description
"Easy-launch buttons" on page 10
"Launch keys" on page 10
# Item
#
# Icon Item
Icon Item
Description
Description
Description
Description
#
1
2
3
#
N/A
N/A
Icon
Item
Item Description
Speakers Left and right speakers deliver stereo audio output.
# Icon Item Description
Latch Locks and releases the LCD panel.
Lights up when the computer is on.
4
# Icon
# Icon
Item
Item
# Icon Item
#
6
#
7
Icon
Icon
Item
Item
Line-in jack
Microphone jack xD-Picture Card (xD). Only one card can operate at any given time.
Description
Description
Accepts audio line-in devices (e.g., audio CD player, stereo walkman).
Accepts inputs from an external microphones.
8 Headphones/speaker/ line-out jack with S/
PDIF support
9 Bluetooth communication button/ indicator
10
#
#
Icon
Wireless
Item
Item
button/indicator
11 Four-pin IEEE 1394 port
12 Infrared port
Connects to audio line-out devices (e.g., speakers, headphones).
Slide to enable/disable Bluetooth function. Lights to indicate the status of Bluetooth communications.
(optional)
Slide to enable/disable Wireless function. Lights to
Description
(optional)
Connects to IEEE 1394 devices.
Interfaces with infrared devices (e.g., infrared printer and IR-aware computer).
Chapter 1
# Icon Item Description
# Icon
# Icon
Left View
Item
Item
Description
Description
Note:
8
9
#
# Icon
Icon
Item
Item
1
#
#
Icon Item
Kensington lock slot
Description
Description
Description
Connects to a Kensington-compatible computer security
2 Two USB 2.0 ports
3 Modem (RJ-11) port
Connect to USB 2.0 devices (e.g., USB mouse, USB camera).
Connects to a phone line.
4
5
6
7
N/A
N/A
N/A
N/A
N/A
Note:
Optical disk drive Accepts CDs or DVDs, depending on the optical disk type.
Optical disk access indicator
Optical disk drive eject button
Lights up when the optical disk drive is active.
Ejects the optical disk from the drive.
Emergency eject hole Ejects the optical drive tray when the computer is turned off.
ExpressCard /34 slot
PC Card slot
Accepts a 34 mm PCI Express Card.
Accepts one Type II PC Card
10 N/A PC Card slot eject
# Icon Item button
Ejects the PC Card from the slot.
Description
# Icon Item Description
Chapter 1
Note:
7
# Icon Item Description
Item
Note:
Description # Icon
Right View
# Icon Item
Note:
Description
#
# Item
Item
1
#
SmartCard slot
# Icon Item
2
#
3
#
4
Description
Description
Accepts the TravelMate SmartCard.
Description
Icon Item
Two USB 2.0 ports
N/A Ventilation slots
Ethernet (RJ-45) port
Description
Connect to USB 2.0 devices (e.g., USB mouse, USB camera).
Description
Connects to an Ethernet 10/100/1000-based network
(for selected model).
5 External display (VGA) port
Connects to an external display device (e.g., external monitor, LCD projector).
Rear View
#
# Icon
Icon Item
Item Description
Description
#
# Icon Item
#
#
Icon
Icon
Icon
Item
Item
1
#
DVI-D port
Item
Description
Description
Description
Note:
Description
2
#
3
4
5
Icon Item
124-pin port (Replicator connector)
Connects to Acer ezDock.
Description
# Icon Item
N/A port
Battery
DC-in jack
Connects to a television or display device with S-video input.
Powers the computer.
Connects to an AC adapter.
Note:
8
# Icon Item
Note:
Description
Chapter 1
# Item Description
Bottom View
#
1
2
3
4
5
6
7
8
9
#
Item
Battery lock
Battery bay
Battery release latch
Optical drive bay release latch
Optical drive bay
Hard disk bay
Acer DASP (disk Anti-
Shock Protection)
Wireless LAN and memory compartments
Ventilation slots and cooling fan
Description
Locks the battery in position.
Description
Houses the computer’s battery pack.
Releases the battery for removal.
Releases the optical drive for removal.
Houses the computer’s optical drive.
Houses the computer's hard disk.
Protects the hard disk drive from shocks and bumps.
Houses the computer's Wireless LAN and main memory.
Keep the computer cool. Do not cover or obstruct the opening of the fan.
Note
Chapter 1 9
Using the Keyboard
The full-sized keyboard includes an embedded numeric keypad, separate cursor keys, two Windows keys and twelve function keys.
Lock keys
The keyboard has three lock keys, each with its own status indicator.
Lock key
Lock Key
Caps Lock
<Fn> + <F11>
Scroll Lock
<Fn> + <F12>
<Fn> + <F12>
Description
Description
When Caps Lock is on, all alphabetic characters are typed in uppercase.
When Num Lock is on, the embedded keyboard is in numeric mode.
When Scroll Lock is on, the screen moves one line up or down when you press the up or down arrow keys respectively. scroll
Lock does not work with some applications.
Embedded Numeric Keypad
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters located on the right part of the keycaps.
Desired access Num Lock on Num Lock off
<Shift>
<Fn>
<Fn>
Lock key
Desired access
Number keys on embedded keypad embedded keypad
Main keyboard keys
Description
Num Lock on
Type numbers in a normal manner.
Hold <Shift> while using cursor-control keys.
Hold <Fn> while typing letters on embedded keypad.
N/A
Num Lock off
Hold <Fn> while using cursorcontrol keys.
Type the letters in a normal manner.
<Fn> + <F12>
10 Chapter 1
Desired access Num Lock on
<Shift>
<Fn>
Num Lock off
<Fn>
Windows keys
The keyboard has two keys that perform Windows-specific functions.
Key
Key
Icon
Description
Description
Windows key This key has the same effect as clicking on the Windows Start button. It launches the Start menu. It can also be used with other keys to provide a variety of functions:
+ Tab: Activates the next Taskbar button.
Application key
Key
+ E: Opens the My Computer window.
Description
< > + <Tab>:
+ F1: Opens Help and Support.
< > + <E>:
+ F: Opens the Find (All Files dialog box).
< > + <Tab>:
< > + <F1>:
<
+ R: Opens the Run dialog box.
< > + <F1>:
+ M: Minimizes all windows.
< > + <F>:
< > + <F>:
Shift +
+ <R>:
+ <R>:
+ M)
< > + <M>: action.
<Shift> + < > + <M>:
< > + <M>:
This key has the same effect as clicking the right mouse button. It opens the application’s context menu.
<Shift> + < > + <M>:
Hotkeys
The computer employs hotkeys or key combinations to access most of the computer's controls like screen brightness, volume output and the BIOS utility. To activate hotkeys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
<Fn>
<Fn> + <F1>
<Fn> + <F1>
Icon
Icon
Function
Function
Description
Description
Description
Hot key help Displays help on hot keys.
<Fn> + <F2>
<Fn> + <F2>
<Fn> + <F2>
<Fn> + <F3>
Acer eSetting page 20
Management
<Fn>
"Acer eManager" on
Launches the Acer ePower Management in the
11
<Fn> + <F5>
<Fn> + <F6>
<Fn> + <F7>
<Fn> + <F7>
<Fn> + <F8>
<Fn> + <F7>
<Fn> + < >
<Fn> + < >
<Fn> + < >
<Fn> + < >
>
<Fn> + < >
<Fn> + < >
<Fn> + < >
<Fn> + < >
<Fn> + < >
Hotkey Icon Function Description
<Fn> + <F1>
Hotkey
<Fn> + <F1>
<Fn> + <F2>
<Fn> + <F1>
Icon Function
Icon Function
Icon Function
Description
Description
Description
Icon Function Description
Icon Function
<Fn> + <F2>
<Fn> + <F1>
<Fn> + <F1>
<Fn> + <F3>
Icon Function
Icon Function
Description
"Acer eManager" on
"Acer eManager" on
page 20
page 20 page 20
"Acer eManager" on
Description
page 20
"Acer eManager" on
page 20 page 20
page 20
page 20 page 20
"Acer eManager" on
"Acer eManager" on
"Acer eManager" on
<Fn> + <F4>
<Fn> + <F5>
Icon
Sleep
Function Description
Leads the computer to Sleep mode.
<Fn> + <F6>
<Fn> + <F6>
<Fn> + <F6>
<Fn> + <F6>
Display toggle
Screen blank
Touchpad toggle
Switches the display output between the display screen, external monitor (if connected) and both.
Turns off the display screen backlight to save power. Press any key to return.
Turns the internal touchpad on and off.
<Fn> + <F7>
<Fn> + <F7>
<Fn> + <F7>
<Fn> + <F8>
<Fn> + <F8>
<Fn> + <F8>
<Fn> + < >
Speaker toggle
Volume up
Volume down
Turns the speakers on and off.
Increases the sound volume.
Decreases the sound volume.
Brightness up Increases the screen brightness.
<Fn> + < >
>
<Fn> + < >
<Fn> + <
>
>
<Fn> + < >
<Fn> + < >
<Fn> + < >
<Fn> + < >
<Fn> + < >
Brightness down Decreases the screen brightness.
12 Chapter 1
Special keys
You can locate the Euro symbol and the US dollar sign on the upper center or bottom right side of the keyboard.
The Euro Symbol
1. Open a text editor or word processor.
Alt Gr> the Euro symbol on the number <5> key.
Euro>
2. Either directly press the <Euro> key on the bottom right side of the keyboard, or hold <Alt Gr> key then press
Note: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/ www.microsoft.com/typography/faq/faq12.htm
The US Dollar Sign
1. Open a text editor or word processor.
2. Either directly press the <$> key on the bottom right side of the keyboard, or hold <Shift> and then press the
US dollar sign on the number <4> key.
<Shift>
<Dollar>
Note: This function varies according to the language settings.
Note:
Chapter 1 13
# Item Description
# Item Description
Indicators
# Item Description
"Launch keys" on page 10 the front cover. These indicators show the status of the computer and its components.
"Launch keys" on page 10
# Item Description
"Launch keys" on page 10
"Launch keys" on page 10
The power, battery, Bluetooth and wireless communication status indicators are on even when the LCD panel is closed.
Icon Function Description
Icon
# Icon Item
Item
Caps Lock
Description
Description
Lights when Caps Lock is activated.
#
# Icon Item
Icon
Description
# Icon Item
Media activity
Description
Glitters when the hard disk or optical drive is active.
Power Lights when the computer is on.
Battery Lights when the battery is being charged.
Bluetooth
1. Charging:
Indicates the status of Bluetooth communication
Indicates the status of wireless LAN communication
14 Chapter 1
Easy-launch Buttons
user-programmable button, web browser button, mail button, and Acer Empowering Key . Press to run the
Acer Empowering Technology.
Although the mail and web browser buttons are pre-set to E-mail and Internet
Launch Manager.
Easy launch button
Easy-launch button
Web browser
P
Default application
Default application
Acer Empowering Technology (user-programmable)
E-mail application (user-programmable)
Internet browser (user-programmable)
User-programmable
Chapter 1
"Easy-launch buttons" on page 10
15
Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor responds as you move your finger across the surface of the touchpad. The central location on the palmrest provides optimum comfort and support.
Touchpad Basics
Use the touchpad as follows:
16
(2)
•
Move your finger across the touchpad (2) to move the cursor.
•
Press the left (1) and right (4) buttons located on the edge of the touchpad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the touchpad (2) is the same as clicking the left button.
•
Use the four-way scroll (3) button to scroll up or down and move left or right a page. This button mimics your cursor pressing on the right scroll bar of windows applications.
Function
Execute
Select
Drag
Left button (1)
Quickly click twice.
Click once
Click and hold.
Then slide your finger across the touchpad to drag the cursor over the selection.
Right button (4) Main touchpad (2)
Tap twice (at the same speed as double-clicking a mouse button).
Tap once
Tap twice (at the same speed as double-clicking a mouse button); rest your finger on the touchpad on the second tap and drag the cursor.
Center button (3)
Access context menu
Scroll
Click once
Click and hold to move up/down/left/ right.
Note: Keep your fingers, as well as the surface of the touchpad dry and clean. The touchpad is sensitive to your finger movements: the lighter the touch, the better the response. Tapping hard will not increase the touchpad’s responsiveness.
Chapter 1
Acer Empowering Technology
Acer’s innovative Empowering Technology makes it easy to have access to the frequently used functions and manage the notebook. It features the following handy utilities:
•
Acer eDataSecurity Management protects data with passwords and advanced encryption algorithms.
•
Acer eLock Management limits access to external storage media.
•
Acer ePerformance Management improves system performance by optimizing disk space, memory and registry setting.
•
Acer eRecovery Management backs up and recovers data flexibly, reliably and completely.
•
Acer eSettings Management accesses system information and adjusts settings easily.
•
Acer eNet Management hooks up to location-based networks intelligently.
•
Acer ePower Management extends battery power via versatile usage profiles.
•
Acer ePresentation Management connects to a projector and adjusts dispaly settings conveniently.
For more information, press the key to launch the Empowering Technology menu, then click on the appropriate utility and select the Help function.
Chapter 1 17
"Easy-launch buttons" on page 10
Acer eDataSecurity Management
Acer eDataSecurity Management is a handy file encryption utility that protects the files from being accessed by unauthorized persons. It is conveniently integrated with Windows Explorer as a shell extension for quick and easy data encryption and decryption and also supports on-the-fly file encryption for MSN Messenger and Microsoft
Outlook.
There are two passwords that can be used to encrypt and decrypt a file: the supervisor password and the filespecific password. The supervisor password is a “master” password that can decrypt any file on the system. The file-specific password is assigned when you encrypt each individual file.
Acer eDataSecurity Management setup wizard will prompt for a supervisor password and default file-specific password. This file-specific password will be used to encrypt files by default, or you can choose to enter your own file-specific password when encrypting a file.
Note: The password used to encrypt a file is the unique key that the system needs to decrypt it. If you lose the password, the supervisor password is the only other key capable of decrypting the file. If you lose both
passwords, there will be no way to decrypt the encrypted files! Be sure to safeguard all related password.
18 Chapter 1
Chapter 1 19
Acer eLock Management
Acer eLock Management is a security utility that allow you to lock up your removable data, optical and floppy drives to ensure that data can not be stolen while your notebook is unattended.
•
Removable data devices: includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives,
USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can be mounted as a file system when plugged into the system.
•
Optical drive devices: includes any kind of CD-ROM or DVD-ROM drives.
•
Floppy disk drives: 3.5-inch disks only.
To activate Acer eLock Management, a password must be set at first. Once set, you may apply locks to any of the three kinds of devices. The lock(s) will be set without any reboot necessary, and will remain locked after rebooting, until unlocked.
If you do not set a password, Acer eLock Management will reset back to the initial status with all locks cancelled.
Note: If you lose the password, there is no method to reset it except by reformatting the notebook or
taking the notebook to an Acer Customer Service Center. Be sure to remember or write down the password.
20 Chapter 1
Acer ePerformance Management
Acer ePerformance Management is a system optimization tool that boosts the performance of the Acer notebook.
It provides you with the following options to enhance overall system performance:
•
Memory optimization: releases unused memory and checks memory usage.
•
Disk optimization: removes unneeded items and files.
•
Speed optimization: improves the usability and performance of the Windows XP system.
Chapter 1 21
Acer eRecovery Management
Acer eRecovery Management is a powerful utility with the need for recovery disks provided by the manufacturer.
The Acer eRecovery Management utility occupies space in a hidden partition on the system’s HDD. User-created backups are stored on D:\ drive. Acer eRecovery Management provides:
•
Password protection
•
Recovery of applications and drives
•
Image or data backup:
•
Backup to HDD (set recovery point)
•
Backup to CD or DVD
•
Image or data recovery tools:
•
Recovery from a hidden partition (factory defaults)
•
Recovery from the HDD (most recent user-defined recovery point)
•
Recovery from CD or DVD
Note: If the computer did not come with a Recovery CD or System CD, please use Acer eRecovery
Management’s “System backup to optical disk” feature to burn a backup image to CD or DVD. To ensure the best results when recovering the system using a CD or Acer eRecovery Management, detach all peripherals
(except external Acer ODD, if equipped), including the Acer ezDock.
Acer eNet Management
Acer eNet Management helps you to quickly and easily connect to both wired and wireless networks in a variety of locations. To access this utility, either click on the “Acer eNet Management” icon on the notebook, or start the program from the Start menu. You also have the option to set Acer eNet Management to start automatically when you boot up the PC.
Acer eNet Management automatically detects the best settings for a new location, while offering you the freedom to manually adjust the settings to match your needs, simply by right clicking on the icon in the task bar.
22 Chapter 1
Acer eNet Management can save network settings for a location to a profile, and automatically apply the appropriate profile when you move from one location to another. The settings stored include network connection settings (IP and DNS settings, wireless AP details, etc.), as well as default printer settings. The security and safety concerns mean that Acer eNet Management does not store username and password information.
Chapter 1 23
Acer ePower Management
Acer ePower Management features a straightforward user interface. To launch it, select Acer ePower
Management from the Empowering Technology interface, or double click the Acer ePower Management icon in the task tray.
AC Mode
The default setting is “Maximum Performance.” You can adjust CPU speed, LCD brightness and other settings, or click on buttons to turn the following functions on or off: Wireless LAN, Bluetooth, CardBus, Memory Card, Audio, and Wired LAN.
DC Mode
To suit your usage, there are four pre-defined profiles: Entertainment, Presentation, Word Processing, and
Maximum Battery. Or, you can define up to three of your own profiles.
Battery Status
For real-time battery life estimates based on current usage, refer to the panel on the lower left side of the window.
You can also click Advanced settings to:
•
Set alarms.
•
Reload factory defaults.
•
Select what actions will be taken when the cover is closed, and set passwords for accessing to the system after Hibernation or Stand-by.
•
View information about Acer ePower Management.
24 Chapter 1
Acer ePresentation Management
Acer ePresentation Management lets you select from two of the most common projector resolution: XGA and
SVGA.
Chapter 1 25
Acer OrbiCam
The Acer OrbiCam is a 1.3 megapixel CMOS camera appropriately mounted on the top of the LCD panel. The camera’s 225-degree ergonomic rotation allows you to capture high-resolution photos or videos up front or at the back of the LCD panel. The Acer OrbiCam fully supports the Acer Video Conference technology so that you can transmit the best video quality over an instant messenger service.
Getting to Know Your Acer OrbiCam
1 2 3
# Item
# Item
2
3
#
1
Item
Lens
Power indicator
Rubber grip (selected models only)
Rotating the Acer Orbicam
The Acer OrbiCam rotates 225 degrees counterclockwise to achieve the desired angle. Refer to the illustrations below:
For your convenience, the camera snaps 45 degrees to match the position of your face in front in back of the LCD panel.
Note: Do not rotate the camera clockwise to prevent it from the damage.
26 Chapter 1
Launching the Acer OrbiCam
To launch the Acer OrbiCam, double click on the Acer OrbiCam icon on the screen or Click Start > All programs
> Acer > Acer OrbiCam. The Acer OrbiCam capture windows window will appear as below:
Changing the Acer OrbiCam settings
Resolution
To change the capture resolution, click the displayed resolution at the bottom right corner of the capture window, then select the desired resolution. Setting the camera resolution to 640 x 480 or larger does not change the capture window size.
Chapter 1 27
Options
size, preview settings, and the folder for captured photos or videos.
Camera Settings
•
Basic settings: Click the Camera Settings icon on the bottom right corner of the capture display, then select Camera Settings from the pop-up menu. You can adjust the Video, Audio, and Zoom/Face tracking options from this window.
Video, Audio
Video, Audio
Camera Settings
Zoom/Face tracking
Zoom/Face tracking
•
Capture settings: From the Camera Settings window, click the Driver Settings button. The Properties window will appear.
Properties
Properties
Driver Settings
Driver Settings
28
Device Settings
Device Settings
Advanced Settings
Advanced Settings
Zoom/Face Track Settings
Zoom/Face Track Settings
Chapter 1
•
Device Settings allows you to change the camera brightness, contrast, hue, saturation, sharpness, etc.
•
Advanced Settings allows you to achieve gain control, implement image mirror, select image enhancements and anti-flicker settings, and turn on/off the camera indicator.
•
Zoom/Face Track Settings allows you to adjust the zoom level and turn the face tracking feature on or off.
Capturing photos or videos
To capture a photo or a video clip, rotate the Acer OrbiCam to get the desired angle, then click the Take a Picture or Record a Video button. The Windows Picture and Fax Viewer or the Windows Media Player automatically launches to display or play a preview of the photo/video clip.
Note: By default, all photos and videos are saved in the My Pictures and My Videos folder.
Using the Acer OrbiCam as webcam
The Acer OrbiCam is automatically selected as the capture device of any instant messenger (IM) application. To use the Acer OrbiCam as a webcam, open the IM service, then select the video/webcam feature. You can now broadcast from your location to an IM partner anywhere in the world.
Enabling the Acer VisageON
The Acer VisageON technology comes with two features: Face tracking and Video effects (selected models only).
The Face Tracking feature tracks your head movement and automatically centers your face in the capture window.
The video effects feature allows you to select and apply an effect to your video transmissions.
Note: The face tracking feature is not capable of centering your face beyond the capture window frame.
Minimal head movements are tracked more efficiently.
To enable the Acer VisageON:
1. Right click on this icon, then select VisageON from the pop-up menu.
VisageON
VisageON
The VisageON window appears as below:
Chapter 1
Users
Users
Single User Multiple
Single User Multiple
29
VisageON
2. Select and apply a video effect in the left section of the VisageON window. Change the face tracking settings and options in the right section.
Using the face tracking feature
To use the face tracking feature:
1. Click the left icon down arrow button, then select Single User or Multiple Users from the pop-up menu. For multiple users, the face tracking feature automatically centers all the users’ face in the capture window, otherwise the utility centers the face of the user closest to the camera.
2. Click the right icon to zoom in/out or reset the current view.
3. Click VisageON to display a menu that allows to change the configuration of the camera, face tracking and video effects settings.
VisageON
Using video effects (selected models only)
Using video effects effect:
Video Settings
Video Settings below:
Effect Selection
Effect Selection
30
Video
Video
Chapter 1
2. Click on a video effect to use. The selected effect appears in the video effects section of the VisageON window.
Note: When using avatars, you may have to calibrate the face points to achieve better tracking. Follow screen instructions in the VisageON to continue.
Note: You may use video effects when using the camera for IM chat/video sessions or call conferences.
Chapter 1 31
Acer GraviSense
Acer GraviSense is an innovative utility designed to further protect your data by automatically moving the read/ write heads of the Acer notebook’s hard disk away from the storage disk (this is known as “parking” the heads) in the event that sudden shock is detected. Acer GraviSense can also be set to activate an alarm in case the notebook is moved by an unauthorized person.
Using Acer GraviSense
Start > (All) Programs > Acer GraviSense.
You can launch Acer GraviSense in a number of ways:
•
From the Start menu, go to Start > All programs > Acer GraviSense
•
When Acer GraviSense is running, an icon will display in the task tray. Move the cursor on the icon to identify Acer GraviSense. Left click or right click on the icon to open a context menu.
Protecting the HDD
Right click on the tray icon to activate this feature and select HDD protection.
This function will park the HDD heads in the event that any sudden vibration or movement which exceeds the level tolerated by the HDD is detected.
Anti-Theft
Right click on the tray icon to activate this feature and select Anti-Theft.
When enabled, this feature will sound an alarm if the notebook is moved. This feature is password-protected to prevent unauthorized access.
Your password needs to be between four and eight characters, and should consist of letters and numbers. Once you’ve set the password, the Anti-theft feature will be activated.
If you enter a password that is invalid for any reason, you will be prompted to try again.
32 Chapter 1
When this function is activated, Acer GraviSense will show a full screen image and a password window.
When Anti-Theft is activated, it will disable the following keys functions:
•
Alt + Tab
•
Ctrl +Shift + Esc
•
Ctrl + Alt + Del
•
Windows keys
•
Task bar
Besides, the settings below will be changed to “do nothing” (the personal settings will be recovered once the Anti-
Theft function is disable):
•
Power button
•
Sleep button
•
Close the lid
If the system detects any movement when this function is activated, the system will emit a beep as a warning and prompt you to enter the password.
Note: Please remember the password for it can not be changed.
Note: You need to disable the Task Manager before setting the Anti-Theft function.
Chapter 1 33
Note:
Using the System Utilities
Note: The system utilities work under Microsoft Windows XP only.
Acer GridVista (dual-display compatible)
Note: This feature is only available on certain models.
Start Control Panel Display
Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the display box and then click the check box Extend my windows desktop onto this monitor. Finally, click Apply to confirm the new
Extend my windows desktop onto this monitor
Apply OK
Settings
Apply
Start Control Panel Display
(2)
Extend my windows desktop onto this monitor
OK
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows on
Acer GridVista
Acer GridVista
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently. Acer GridVista is simple to set up:
1. Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
2. Drag and drop each window into the appropriate grid.
3. Enjoy the convenience of a well-organized desktop.
34 Chapter 1
Note: Please ensure that the resolution setting of the second monitor is set to the manufacturer's recommended value.
Note:
Note:
Launch Manager
Launch Manager by clicking on Start > All Programs > Launch Manager to start the application.
"Easy-launch buttons" on page 24
Start All Programs
Launch Manager
Start All Programs
Launch Manager
Chapter 1 35
Hardware Specifications and Configurations
Item
CPU speed (GHz)
Bus speed (MHz)
Bus/Core Ratio
L2 cache size (MB)
L2 cache speed (GHz)
Package type (pin)
Manufacturing technology (nm)
Thermal design power
Thermal specification ( o
C)
Core voltage (V)
Item
CPU speed (GHz)
Bus speed (MHz)
Bus/Core Ratio
L2 cache size (MB)
L2 cache speed (GHz)
Package type (pin)
Manufacturing technology (nm)
Thermal design power
Thermal specification ( o
C)
Core voltage (V)
Package
Power
Feature
Package
Power
Item
Item
1.0375 ~
1.30
T2700
2.33
667
13
2
2.33
478
65
31W
100
1.0375 ~
1.30
T7600
2.33
667
14
4
2.33
479/478
65
34W
100
1.0375 ~
1.30
T2500
2
667
12
2
2
479/478
65
31W
100
1.0375 ~
1.30
T7200
2
667
12
4
2
479/478
65
34W
100
1.0375 ~
1.30
T2600
2.16
667
13
2
2.16
478
65
31W
100
1.0375 ~
1.30
T7400
2.16
667
13
4
2.16
479/478
65
34W
100
1.0375 ~
1.30
T2400
1.83
667
11
2
1.83
478
65
31W
100
1.0375 ~
1.30
T5600
1.83
667
11
2
1.83
479/478
65
34W
100
Specification
Micro-FCBGA 1466-pin
1.05V (core), 1.5V, VCCSM (DDR2 = 1.8V), 2.5V, 3.3V
• Processor host bus support
• Integrated SDRAM controller up to 4GB (2 SODIMM support)
Integrated SDRAM clock buffer to support 2 SODIMM
• External Graphics interface for PCI Express Architecture support
• DMI x 2 and DMI x 4 for connection between GMCH and ICH7M
Specification
BGA 652-pin
1.05V (core), 1.5V, 3.3V, 5V, CMOS I/O
1.0375 ~
1.30
T2300
1.66
667
10
2
1.66
478
65
31W
100
1.0375 ~
1.30
T5500
1.66
667
10
2
1.66
479/478
65
34W
100
36 Chapter 1
Feature
Item Specification
• Upstream accelerated Hub architecture interface for access to GMCH
• PCI interface (six PCI Request/Grant pairs)
• Bus master IDE controller (support Ultra 33/66/100)
• Serial ATA (SATA) controller
• USB 1.1 and USB 2.0 host controller
• AC’97 2.3 interface
• Low Pin Count (LPC) interface
• IRQ controller
• Enhanced DMA controller, interrupt controller, timers, RTC
• Power management
Model
Drive Specification
Formatted Gbytes (512 bytes/sector)
Physical read/write head
Discs
Spindle Speed (RPM)
Internal transfer rate (Mbytes/sec. max.)
I/O data transfer rate (Mbytes/sec. max.)
ATA data transfer mode supported
Bytes per sector
Average latency
Average seek, read (msec. typical)
Average seek, write (msec. typical)
Cache buffer
Startup current (typical, peak)
Ambient temperature
Temperature gradient ( max.) o
C per hour
Relative humidity
Relative humidity gradient
Drive acoustics, sound power (bels) idle
Shock, operating (Gs max. at 0.5 msec.)
Shock, nonoperating (Gs max. at 2 msec.)
Vibration, operating
Vibration, nonoperating
Nonrecoverable read errors
Seagate
ST9120821AS
120
4
2
5400
57.6
150
ST9120824AS
100
4
2
250
800
1.0 G (0 to peak, 5-500 Hz)
5 Gs (0 to peak, 5-500 Hz)
1 per 10
14 bits read, max.
ST98823AS
80
3
2
SATA 1.0, SATA II
PIO modes 0-4
Multiword DMA modes 0-2
Ultra DMA modes 0-6
1024
5.56
12.5
14.5
8 Mbytes
+5V: 1.1A
5 to 55 o
C (operating), -40 to 70 o
C (nonoperating)
20 o
C (operating), 30 o
C (nonoperating)
5% to 90% (operating), 5% to 95% (nonoperating)
30% per hour max.
2.4 (typical), 2.6 (max)
Chapter 1 37
38
Seek power (typical)
Read/write power (typical)
Idle mode, lower power (typical)
Standby mode
Sleep mode
Voltage tolerance
Seagate
2.20 watts
Read: 1.90 watts; Write: 2.30 watts
0.80 watts
0.28 watts
0.28 watts
+5.0V +/- 5%
Chip
Package
Power
Feature
Item
Clock synthesizer
Feature
Chipset
Feature
Chip
Package
Interface
Item
Item
Item
Description
ICS954310BGLF or pin compatible device
64-pin TSSOP
3.3V
• Spread spectrum function support, for reducing EMI
• SM bus interface support
• 133/166 MHz for CPU and GMCH
• 100 MHz clock buffer for GMCH, ICH7M, PCI-E device, SATA and
Docking station
• 96MHz GMCH
• 48MHz for USB clock inside ICH7M
• 33MHz PCI clock for PC device, SIO, LPC
• 14.31818MHz for ICH7M and audio
Description
• 14.31818MHz crystal for clock chip
• 32.768KHz for RTC inside ICH7M and HS97551
• 24.576MHz/48MHz O2MICRO OZ711MP1
• 27MHz crystal for ATI VGA M56P
• 25MHz crystal for GigaLAN 82573E (Tekoa)
Description
Intel ® 945PM (Calistoga)
• DDR2 533/667 MHz SDRAM memory interface design
• No DDR RAM on board
• Two DDR SODIMM slots
• Maximum memory up to 2GB for 32bit OS, 4GB for 64bit OS (with two
1GB/2GB SODIMM)
Description
Andigilog aSC7511
Eight-pin SSOP
I
2
C bus, address: 98h
Chapter 1
Vendor
Version
Item
ROM type
Package
Block size
Supply current
Chip
Package
Feature
Chip
PCMCIA
Feature
Item
Item
IEEE 1394
Feature
Memory card reader
Feature
Description
Phoenix v2.002e
SST 39VF080, one MB CMOS Boot block Flash Memory
40-pin TSOP
64KB per block
• Active current: 15 mA (typical)
• Standby current: 4 uA (typical)
Description
ATI M56P with VRAM 128MB/256MB
BGA 708-pin
• PCI-E interface support
• 3D graphics texturing enhancements
• Integrated transform and lighting
• Integrated two channels of 24bit LVDS transmitter to support up to
SXGA LCD
• Integrated TV decoder to support S-video with both PAL and NTSC through EZ-4
• 128MB/256MB DDR3 memory
• DVD-ready motion compensation for MPEG-2
• Full ACPI compliant
• ZV port support
Description
O2 Micro OZ711MP1
• PCI single chip solution, PCI 2.2 compliant
• OHCI v1.1
• IEEE 1394.A four-pin
• PC card 95 support with one Type II PCI Card bus
• Reserved PCI-Express one wide type ME
• Five-in-one Card Reader
Controller
Item
Package
Chapter 1
NS PC87383
TQFP 64-pin
Description
39
Feature
Power consumption
Chip
Feature
Item
Chip
Feature
Item
Item
Connector type
Description
Parallel interface support:
• An Enhanced Parallel Port (EPP) compatible with EPP 1.9, version
EPP1.7 of the Xircom specification support
• An extended capabilities port that is IEEE 1284 compliant including level two
UART serial port interface:
• MIDI baud rate support
• Infrared support on UART2 (IrDA 1.1 support)
PnP support:
• Flexible IRQs, DMAs and base addresses
• IRQs that can be multiplexed to the ten supported IRQs
5V / 25 ~ 55 mA
Description
Realtek ALC833D Azadia Codec and Amplifier Maxim MAX9755
• HD Audio
• SNR > 85, high-performance DACs with 95dB SNR (A-Weighting),
ADCs with 85dB SNR (A-Weighting)
• Internal Microphone
• Two speakers, at least 1.5W / 30cc for each
• 2* digital microphone array
• VoIP function support
• Universal jack function support
Description
Intel
®
Tekoa GigaLAN (82573E)
• PCI-E GbE LAN
• WOL support from S5
• LDCM support
• Intel
®
AMT and Wake-on-LAN support
RJ-45
40
Item
Model name
Support disc format
Specification
HLDS GSA-4082N 8X SUPER
MULTI
PANASONIC UJ-840B SUPER
MULTI
DVD-ROM, DVD-R, DVD-RAM,
DVD-RW, DVD+R, DVD+RW;
CD-ROM, CD-ROM XA, CD-I,
Video CD, CD-Extra, CD-Text,
Photo CD, CD-DA, CD-R, CD-
RW
DVD-Video, DVD-ROM, DVD-R,
DVD-RW, DVD+R, DVD+R DL,
DVD+RW, CD-DA, CD-ROM,
CD-R, CD-RW, CD-ROMXA,
Photo CD (multisession), Video
CD, CD-Extra (CD+), CD-Text,
Hybrid SACD
Chapter 1
Transfer rate
Interface
Item
Operating voltage
Feature
Item
Specification
DVD-ROM 16.62Mbytes/sec.
(12X) max.
CD-ROM 4800 kB/sec. (32X) max.
DVD-ROM 10.55 Mbytes/sec.
(8X) max.
CD-ROM 3600 kB/sec. (24X) max.
IDE (ATAPI)
+5.0V +/- 5%
IDE (ATAPI)
+5.0V +/- 5%
Description
• Mini-card: manufacturing option
• 802.11a/b/g (Intel
®
Golan / 3 rd
party)
• 802.11 pre-n (3 rd
party)
• Built-in two antennas
• Wi-Fi CERTIFIED TM solution, WPA2, WMM
• CCX V3 and above
Controller
Item
Data modem data baud rate (bps)
Modem/bluetooth protocol supported
Connector type
ICH7M
56K
Description
• V.90/V.92 AC-Link modem with PTT approval
• Wake-on-Ring ready
RJ-11
Module
Controller
Feature
Item Description
WNC BU5 Bluetooth miniUSB module
ICH7M
• Bluetooth 1.1 qualified embedded USB module
• Class two specification RF output power (max. + four dBm)
• Full piconet and scatternet operation
• Full Bluetooth data rate (723 KB/s)
• USB 1.1 compliant interface
• LED indicator built-in
Chip
Package
Feature
Item Description
PC97551
LQFP 176-pin
• Host interface, base on Intel
®
’s
LPC interface specification revision 1.0
• PC01 REV 0.3 and ACPI 1.0b compliant
• 16bit risc core, with two MB address space, up to 20 MHz
• Software and hardware controlled clock throttling
• Share BIOS flash memory (internal and/or external)
• 84 GPIO ports with variety of wake-up events
• JTAG-base debugger interface
Chapter 1 41
42
Controller
Item
Model name
Feature
Feature
Item
Description
PC97551
Travelmate series: New Acer Ergo Keyboard with buttons embedded
• 88/89-key Acer FineTouch TM keyboard with five-degree curve
• Inverted T cursor layout
• 2.5 mm (minimum) key travel, spill proof support
• Built-in touchpad with four-way integrated scroll button
• 12 function keys
• Four cursor keys
• Two Windows ® keys
• Hotkey controls
• Embedded numeric keypad
• International language support
• Four easy-launch buttons: web browser, mail, empowering key and user-programmable
• Two front-access recovery type LED switch: WLAN, Bluetooth
®
Item
System core logic
Super I/O
PCMCIA & IEEE 1394
& Card Reader
Audio
Video
Keyboard
LAN
Controller
• North bridge: Intel
®
945PM (Calistoga)
• South bridge: ICH7M
NS PC87383
O2 711MP1
Realtek ALC883
ATI M56P
PC97551
Intel
®
Tekoa GigaLAN 82573E
Description
• 120 pins for signals and four pins for power
• Power supplied from Acer ezDock
• Max. six USB ports support
• Two 1394 ports support
• One new card socket and one PCMCIA card socket
• GigaLAN and modem support
• analog VGA, TV out and DVI-D support
• One parallel, one serial port and two PS2 port for legacy devices support
Item
Vendor & model name
Battery Type
Pack capacity
Number of battery cell
Specification
Panasonic pack 7800MAH / Sanyo pack 2600MAH
Li-Ion
87 W nine cell six cell (optional: 42 W 3800MAH Li-Ion 2nd battery pack)
Chapter 1
Battery life
Off
On
Item
Legacy Mode
Specification
• 80% charge in one hour
• two hour rapid charge system-off
• 2.5 hour charge-in-use
ACPI Mode
• Mech. Off (G3): All devices in the system are turned off completely.
• Soft Off: (G2/S5): All devices in the system are turned off completely by OS shutdown.
• Working (G0/S0): Individual devices such as the CPU and hard disk may be power-managed in this state.
• S3 Sleeping State: CPU set power down, VGA suspend, PCMCIA suspend, Audio power down, HDD power down, CD-ROM power down, Super I/O low power mode.
• S4 Sleeping State: It is also called hibernation state. The system saves all system setting and data onto disk before the whole system is powered off.
Event
Power Button
LAN (onboard)
RTC
Lid Open
Embedded Software
Modem
USB Input Device
Any Key from Internal
Keyboard
PS/2 Input Device
Battery Critically Low
Yes
No
Yes
No
Yes
No
Yes
Item
Model name
Display area
Driver element
Display colors
Number of pixel
Pixel arrangement
S3
Yes
Yes
S4
Yes
Yes
Yes
No
No
No
No
No
No
S5
Yes
Yes
In S4 and S5, this feature is supported only with AC in.
This feature is supported only with AC in.
Remark
This event only runs for onboard LAN.
In S4 and S5, this feature is supported only with AC in.
Yes
No
No
No
No
No
No This event should wake the system to
Full On then notify the OS of the critically low batter.
Samsung LTN154P1-
L02
331.38 (H) X
207.1125 (V) mm
(15.4” diagonal) a-Si TFT active matrix
262,144
1680 X RGB (3)
X1050 pixels
RGB vertical stripe
Specification
CMO N154Z1-L01
331.128 (H) X
206.955 (V) mm
(15.4” diagonal) a-Si TFT active matrix
262,144
1680 X RGB (3)
X1050 pixels
RGB vertical stripe
-
QDI QD 15AL02-01
331.2 (H) X 207.0 (V) mm (15.4” diagonal)
262,144
1680 X RGB (3)
X1050 pixels
RGB vertical stripe
Chapter 1 43
44
Item
Pixel pitch
Display mode
Surface treatment
Model name
Input feature
Rated voltage
Item
Input voltage range
Rated frequency
Frequency range
Steady AC current
Output feature
Rated voltage
Voltage range
Rated power
Output ripple and noise
Turn on delay time
Pin Number
0.19725 (H) X
0.19725 (V) mm
Normally white
Haze (25), Hardcoating (3H)
Specification
0.1971 (H) X 0.1971
(V) mm
Normally white
Antiglare and Hard
Coat (3H min.)
0.1971 (H) X 0.1971
(V) mm
Normally white
Antiglare, Hardness
3H
LiteOn PA-1900-04QB
Specification
ROHS Delta 90W ADP-
90SB BBAHF for 100Vac or 240Vac input
AC voltage from 90Vac to 264Vac for 50Hz or 60Hz from 47Hz to 63Hz less than 1.5A rms at
100Vac input and maximum load for 100Vac or 240Vac input
AC voltage from 90Vac to 265Vac for 50Hz or 60Hz from 47Hz to 63Hz less than 1.5A rms at
100Vac input and maximum load
19V
18.05V to 20V
90 W less than 300mVp-p within two seconds at 115
Vac input voltage three pin
19V from 18.2V to 19.8V
90 W less than 300mVp-p within two seconds at 115
Vac input voltage three pin
Item
Dimensions
Weight
Description
364 (W) x 271 (D) x 26.3/38 (H) mm (14.33 x 10.66 x 1.03/1.49 inches)
3 kg (6.6 lbs.) for 15.4 LCD model
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built in the BIOS (Basic Input / Output System) of computer. Generally speaking, the computer is already properly configured and optimized, and you do not need to run this utility.
However, if you encounter configuration problems, you may need to run Setup. Otherwise, you can also refer to
Chapter 4 Troubleshooting when problem arises.
Invoking BIOS Setup
To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prompted on the left-bottom side of the screen).
There are six prime items in the BIOS Setup Utility. They are Information, Main, Advanced, Security, Boot and Exit.
In the coming pages, we will explain the BIOS Setup Utility by item.
Part
Information
Main
Advanced
Security
Boot
Exit
Description
Display the system informations.
Allows the user to specify standard IBM PC AT system parameters.
Provides advanced setting of the system.
Provides security setting of the system.
Allows the user to specify the boot options.
Allows the user to save CMOS setting and exit Setup.
Note: During setup, all Fn function keys and power saving function are disabled.
Chapter 2 45
Buttons
Hotkeys
•
Fn + F1 (Help Menu): This hotkey will cause a help message on the screen that describes the definitions and functions of the unit’s hotkeys.
•
Fn + F2 (Launch Acer eSetting): This hotkey will launch the Acer eSetting utility.
•
Fn + F3 (Launch Acer ePower Management): This hotkey will launch the Acer ePower management utility.
•
Fn + F4 (Sleep Button): It is assigned as the Sleep Button in ACPI mode. Users can set the definition of
Sleep Button in Windows Power Options.
•
Fn + F5 (Display Toggle): It’s used to switch the display device at run-time. The detail behavior is defined in Acer Display Mode Specification v0.02.
•
Fn + F6 (Display Blank): This hotkey will make the LCD backlight turned off. This provides both a quick security features and some power savings. The LCD backlight will be turned on again when any of the following events occurs:
•
Any key pressed (not include USB keyboard)
•
Pointing device moved (not include USB mouse)
•
Fn + F7 (Touchpad On/Off): This hotkey will cause the internal touchpad to be disabled/enabled.
•
Fn + F8 (Speaker On/Off): It’s assigned to turn on and turn off the audio output.
•
Fn + F11 (Number Lock): The NumLock feature is a standard AT keyboard feature. In Acer system, the
NumLock is off by default and for the internal keyboard as numeric keypad lock when the NumLock is on.
If an external keyboard or keypad is linked, the NumLock will have the following limits:
•
NumLock is on when the system boots with external keyboard or numeric keypad. The external keyboard or keypad NumLock status is on and internal keyboard overlay numeric keys are disabled.
•
NumLock key can be typed on or off via the internal keyboard (Fn + F11) or the external keyboard or keypad, but NumLock affects the external keyboard or keypad only.
•
The NumLock shift state (NumLock is off) is NOT used for the cursor movement by the internal keyboard numeric keys.
•
The state of the NumLock is not changed by the linkage and removal of the external keyboard or keypad. This is to support the linkage of an external numeric keypad. It permits the users for full alphabet typing with the internal keyboard, and the external keypad for numeric typing.
•
Fn + F12 (Scroll Lock): The Scroll Lock is a standard AT keyboard feature.
•
Fn + K (Volume Up): It is assigned to increase the volume.
•
Fn + L (Volume Down): This hotkey is used to decrease the volume.
•
Fn + J (Brightness Up): It is assigned to increase the brightness of the LCD backlight.
•
Fn + I (Brightness down): It is used to decrease the brightness of the LCD backlight.
•
Fn + <Page Up> (Home): This is a standard AT keyboard feature. When it is pressed, the cursor on the screen will skip to the beginning of the line.
•
Fn + <Page Down> (End): It is a standard AT keyboard feature. When it is pressed, the cursor on the screen will skip to the end of the line.
Launch Buttons
•
: Launch Acer eManager
•
P: Launch Application (programmable)
•
WWW: Web Browser
•
Email: Launch Email
•
Wireless: Wireless enabled/disabled
•
Bluetooth: Bluetooth enabled/disabled
46 Chapter 2
"Easy-launch buttons" on page 10
Power Button
The Power button should act as the ACPI defined Power button and users can determine its policy through the OS setting like Windows Power Options.
The override feature should be supported to allow the unconditional shutdown by pressing the Power button for more than four seconds.
Lid Switch
The function of Lid switch is defined as below:
•
The LCD backlight should be turned off when the Lid switch is pressed. The LCD backlight will be lighted when the Lid switch is released again. This function is irrelevant to OS and should be always true when the system is powered on.
•
When the system is running under ACPI mode, the function of the Lid switch should follow the OS setting.
Auto-Dim
The system supports an automatic dimming of the LCD brightness when the AC power source is not available
(running on battery power). However, the users still can manually adjust the LCD brightness by their need. The current user setting of brightness (along with current power source) will be saved across power down and be restored at the next boot or resume.
Chapter 2 47
Information Menu
. Info.
Main
PhoenixBIOS Setup Utility
Advanced Security Boot
Intel(R) Pentium (R) M CPU
2000 MHz
000 @ 2.00GHz
HDD Model Name:
HDD Serial Number:
ST98823AS
3PK016YX
HL-DT-ST DVDRAM GSA-4082N ATAPI Device:
System BIOS Version: v2.002e
VGA BIOS Version:
ATi 009.012.001.000
KBC Version:
Serial Number:
Asset Tag Number:
V.1A17
LXT123ZC1000420076EF00
Product Name:
TravelMate 8200
Manufacturer Name: Acer
UUID:
004CEEEDBC630010AC3AFFFFFFFFFFFF
Exit
F1
Help
Esc
Exit
↑ ↓
← →
Select Item
Select Menu
F5/F6
Change Values
Enter
Select
4
Sub-Menu
F9
Setup Defaults
F10
Save and Exit
•
HDD Model Name: This item will show the Model name of HDD installed on Primary IDE master. The hard disk model name is automatically detected by the system. If there is no hard disk present or unknown type, “None” should be shown on this field.
•
HDD Serial Number: This item will show the Serial number of HDD installed on Primary IDE master. If no hard disk or other devices are installed on Primary IDE master, it will display a blank line.
•
UUID: It shows only when an internal LAN device is available.
Note: Other items are unit dependent.
48 Chapter 2
Main Menu
Info.
Main
PhoenixBIOS Setup Utility
Advanced Security Boot Exit
Item Specific Help
<Tab>, <Shift-Tab>, or
<Enter> selects field.
System Time:
System Date:
System Memory:
Extended Memory:
Video Memory
Quiet Boot:
Power On Display:
Network Boot
F12 Boot Menu:
D2D Recovery:
Processor Power Management:
[14:13:43]
[11/25/2005]
640 KB
1022 MB
256 MB
[Enabled]
[Both]
[Enabled]
[Disabled]
[Enabled]
[Enabled]
F1
Help
Esc
Exit
↑ ↓
← →
Select Item
Select Menu
F5/F6
Change Values
Enter
Select
4
Sub-Menu
F9
Setup Defaults
F10
Save and Exit
•
System Time and System Date: The hours are displayed with 24-hour format. The changes in these two items take effect immediately.
•
System Memory: This item reports the memory size of system base memory. The size is fixed to 640KB.
•
Extended Memory: It reports the memory size of the extended memory in the system. The extended memory size is equal to total memory size (one MB).
•
Video Memory: It indicates the video memory size.
•
Quiet Boot:
•
Enabled: Customer Logo is displayed, and Summary Screen is disabled.
•
Disabled: Customer Logo is displayed, and Summary Screen is enabled.
•
Power on Display:
•
Auto: During power on process, the system will detect if any display device is connected on external video port. If any external display device is connected, the power on display will be only in CRT (or projector) mode. Otherwise, it will be in LCD mode.
•
Both: Both the integrated LCD and the external video port (for an external CRT or projector) will be enabled simultaneously.
•
Network Boot: It permits the users to boot from network.
•
F12 Boot Menu:
•
Enabled: When it is enabled, the users can modify device boot priority by pressing <F12> during
POST.
•
Disabled: When it is not enabled, device boot priority will not be adjustable during POST. The boot
Chapter 2 49
device change is only for one-time change. In other words, when the system is rebooted, the boot device sequence will be the same as the one defined in the BIOS setup (Boot option).
•
D2D Recovery: It allows the users to enable or disable the disk-to-disk recovery.
•
Processor Power Management: To save power in working state, the OS leads the CPU to low-power states (C1, C2 and C3) when the OS is idle. In the low-power state, the CPU does not run any instructions, and wakes up when an interruption, such as the OS scheduler’s timer interruption, occurs.
50 Chapter 2
Advanced Menu
Info.
Main
PhoenixBIOS Setup Utility
Advanced Security
Serial port A:
Infrared Port:
Parallel port:
Mode:
[Auto]
[Auto]
[Auto]
[ECP]
Boot Exit
Item Specific Help
Configure serial port A using options:
[Disable]
No configuration
[Enabled]
User configuration
[Auto]
BIOS or OS chooses
configuration
(OS Controlled)
Displayed when
controlled by OS
F1 Help
Esc Exit
↑ ↓
← →
Select Item
Select Menu
F5/F6 Change Values
Enter Select
4
Sub - Menu
F9 Setup Defaults
F10 Save and Exit
•
Serial Port A:
•
Disabled: No configuration
•
Enabled: User configuration
•
Auto: BIOS or OS chooses configuration.
•
Infrared Port:
•
Disabled: No configuration
•
Enabled: User configuration
•
BIOS or OS chooses configuration.
•
Parallel Port:
•
Disabled: No configuration
•
Enabled: User configuration
•
Auto BIOS or OS chooses configuration.
•
Mode: It permits to set the mode for the parallel port. There are four modes: output only, bi-directional,
EPP and ECP.
Chapter 2 51
Security Menu
Info.
Main
PhoenixBIOS Setup Utility
Advanced
Security
Supervisor Password Is:
User Password Is:
HDD Password Is:
HDD Master ID:
Set Supervisor Password
Set User Passord
Set HDD Password
Password on boot:
Clear
Clear
Clear
19893803
[Enter]
[Enter]
[Enter]
[Disabled]
Boot
Exit
Item Specific Help
Supervisor Password controls access to the setup utility.
F1
Help
Esc
Exit
↑ ↓
← →
Select Item
Select Menu
F5/F6
Change Values
Enter
Select
4
Sub-Menu
F9
Setup Defaults
F10
Save and Exit
The system supports three levels of password protection. The password support consists of a Supervisor
Password, User Password, and Hard Disk Password. All the passwords are stored in a non-volatile storage device
(EEPROM).
•
All the passwords will obey the following rules:
•
All the passwords can be set or cleared in BIOS Setup Security screen.
•
The password entry consists of eight alphanumeric characters. At least one character must be assigned.
•
The valid keys are listed in the table below:
Symbol Character
A-Z
0-9
]
[
-
=
,
.
;
Symbol Name
letters A to Z (not case sensitive) numerical characters dash equal sign left bracket right bracket period comma semi-colon
52 Chapter 2
Symbol Character
/
\
Symbol Name
slash back slash
•
The users can not change or remove password during resuming from S4.
•
The max. number of times to retry the password is limited to three.
•
Supervisor Password:
•
Supervisor Password controls the access of the whole BIOS Setup Utility. If the Supervisor Password is set, the system will pop up the password dialog box to ask for the password when the users press
<F2> for entering BIOS Setup Utility.
•
If the Supervisor Password is set and Password on boot is enabled, the system will pop up the password dialog box to ask for the password when the system is powered on or resumes for S4 state.
•
If the users fail three times consecutively in password verification, the system will be hung up and the users need to manually power off the system.
•
User Password:
•
If the User Password is set, the system will pop up the password dialog box to ask for the password when the users press <F2> for entering BIOS Setup Utility.
•
If the Supervisor Password is not set at first, the User Password can not be set. If the Supervisor
Password is cleared, the User Password will be cleared, too.
•
If the User Password is set and Password on boot is enabled, the system will pop up the password dialog box to ask for the password when the system is powered on or resumes for S4 state.
•
If the users fail three times consecutively in password verification, the system will be hung up and the users need to manually power off the system.
•
Set Supervisor Password / User Password:
•
Highlight the item and press “Enter”, a dialog box will be shown to ask the users to enter new password and confirm new password.
•
If the users want to reset password, a current password will be required to be tapped in at first. If the current password is correct, the users are permitted to enter new password and confirm new password for verification. If the verification is OK, the password setting will be complete after the users press “Enter”.
•
If the password entered does not match the current password, a dialog box will be shown to ask to reenter the password.
•
Password on Boot: It allows the user to specify whether or not a password is required to boot.
Chapter 2 53
Boot Menu
Info.
Main
PhoenixBIOS Setup Utility
Advanced Security
Boot
Exit
1: USB KEY:
2: USB FDC:
3: USB HDD:
4: IDE 0:
5: IDE 1:
6: IDE 2:
FUJITSU MHT2040AH-(USB 2.
ST98823ASIDE S
HL-DT-ST DVDRAM GSA-4082N
7: USB CDROM:
8: PCI LAN: IBA GE Slot 0300 v1230
Item Specific Help
Keys used to view or configure devices:
Up and Down arrows select a device.
<+> and <-> moves the device up or down.
<f> and <r> specifies the device fixed or removable.
<x> exclude or include the device to boot.
<Shift + 1> enables or disables a device.
<1- 4 > Loads default boot sequence.
F1
Help
Esc
Exit
↑ ↓
← →
Select Item
Select Menu
F5/F6
Enter
Change Values
Select 4 Sub-Menu
F9
F10
Setup Defaults
Save and Exit
This menu allows the users to decide the order of bootable devices to load the operating system. It identifies all the bootable devices in the system and attempts to boot them in the order specified. Bootable devices include the diskette drive in module bay, the hard disk and the CD-ROM/DVD drive in module bay and onboard LAN device.
54 Chapter 2
Exit Menu
Info.
Main
Exit Saving Changes
Exit Dicarding Changes
Load Setup Defaults
Discard Changes
Save Changes
PhoenixBIOS Setup Utility
Advanced Security Boot
Exit
Item Specific Help
Exit System Setup and save your changes to CMOS.
F1
Help
Esc
Exit
↑ ↓
← →
Select Item
Select Menu
F5/F6
Enter
Change Values
Select 4 Sub-Menu
F9
F10
Setup Defaults
Save and Exit
•
Exit Saving Changes: It allows the users to save changes to CMOS and reboot the system.
•
Exit Discarding Changes: The users can exit the Setup not to save changes.
•
Load Setup Defaults: It allows the users to load default values in CMOS Setup.
•
Discard Changes: The users can discard previous changes in CMOS Setup.
•
Save Changes: The users can save current changes in CMOS Setup.
Chapter 2 55
Chapter 3
Machine Disassembly and Replacement
General Information
This chapter contains step-by-step procedures on how to disassemble the notebook for maintenance and troubleshooting.
To disassemble the computer, you need the tools below:
•
Wrist ground strap and conductive mat for preventing electrostatic discharge
•
Small Philips screw driver
•
Plastic flat head screw driver
•
Hexagonal driver
•
Tweezers
Note: The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components. When you remove the stripe cover, please be careful not to scrape the cover.
Before You Begin
Before proceeding with the disassembly procedure, you have to make sure that:
1. The system and all peripherals are powered off.
2. The AC adaptor and all power and signal cables from the system are unplugged.
3. The battery pack is removed.
Note: There are several types of screws used to secure the main unit. The screws vary in length. Please refer to the screws table after the flowchart. Group the same type of screws together during service disassembling.
Please also remember the screw location for each screw type. If you fasten the screws on the wrong location, the long screws may cause irrecoverable damage to the main board.
Chapter 3 56
Disassembly Procedure Flowchart
The flowchart gives you a graphic representation on the entire disassembly and reassembly and instructs you how to remove the components.
57 c d a b e
Item Description
SCREW M2.0*2.5-I (NI) (NYLOK)
SCREW M2.5*6-I (BNI) (NYLOK)
SCREW M2.0*3.0-I-NI-NYLOK
SCREW M2.0*6.0-I-NI-NYLOK
SCREW M2.5*2-I (NI, NYLOK)
Chapter 3
f g h j i
Item Description
SCREW 2.5*3-I (NI, NYLOK)
SCREW 2.5*6-I (BNI) TAP
SCREW M2.5*4-I (BNI)
SCREW M2.5*4.0-I (NYLOK) EU
NUT IO EA1
Chapter 3 58
Disassembly Procedure
Removing the Battery Pack
1. Unlock the battery pack.
2. Slide the battery latch, hold it then remove the battery.
Removing the HDD Module
1. Release the two screws fastening the HDD module cover.
2. Detach the HDD module cover.
3. Release the screw fastening the HDD module.
4. Pull the HDD module backwards carefully then remove it.
59 Chapter 3
Removing the Memory and the MiniPCI Card
1. Release the five screws fastening the heatsink cover.
2. Detach the heatsink cover.
3. Pop up the memory card.
4. Then remove it from the slot.
5. Disconnect carefully the main wireless antenna and the auxiliary wireless antenna.
6. Release the two screws fastening the miniPCI card then remove the miniPCI card.
7. Disconnect carefully the bluetooth module.
8. Slide the latch then remove the ODD module from the main unit.
Chapter 3 60
Disassembling the Main Unit
1. To remove the middle cover, you have to remove the two screws on the rear side.
2. Open the notebook as shown. Detach the middle cover carefully because the cable of LED board and main board is under the middle cover.
3. Disconnect the middle cover side cable then remove the middle cover.
4. Release the connector then disconnect the main board side cable as shown.
5. Remove the two screws fastening the keyboard.
6. Detach the keyboard carefully then turn it over as shown.
7. Disconnect the keyboard then remove the keyboard.
8. Disconnect the LCD cable.
9. Pull out the wireless antenna set from the main unit carefully.
61 Chapter 3
10. Disconnect the microphone line and take it out from the main unit carefully.
11. To detach the LCD module, you have to remove the four screws fastening the LCD hinges and the main unit.
12. There is a metal ring fastened on the right hinge. Do not mismatch when reassembling.
13. Then detach the LCD module.
14. Disconnect the touchpad cable.
Chapter 3 62
15. To separate the upper case from the main unit, you have to remove seven screws fastening the upper and lower case assembly.
16. Then remove the 18 screws on the bottom side of the main unit holding the upper and lower cases. One of these 18 screws secures the fan (marked in red).
17. Finally, remove the two hexagonal screws on the rear side of the main unit.
18. Now detach the upper case from the main unit.
19. Release the connector and disconnect the Smart Card reader cable.
20. Disconnect the USB board cable.
21. Disconnect the speaker set cable.
22. Disconnect the other USB board cable on the bottom side of the main unit.
23. Disconnect the fan cable.
63 Chapter 3
24. Remove the two screws fastening the fan.
25. Then detach the fan.
26. Remove the two screws fastening the modem board.
27. Detach the modem board from the main board carefully then disconnect it.
28. Remove the screw fastening the main board.
29. Separate the main board from the lower case carefully.
30. Disconnect the RTC battery on the main board then detach it.
31. Release the five screws fastening the heatsink then detach the heatsink.
32. Release the screw fastening the CPU by rotating the screw counter clockwise then detach the CPU.
33. Remove the screw fastening the charge board then detach it from the main board.
Chapter 3 64
34. Remove the three screws fastening the Smart Card reader then detach the Smart Card reader from the lower case.
35. Pull the latch backwards softly and detach the USB board from its position.
36. Then disconnect carefully the four-pin USB cable, 10-pin USB cable and modem cable.
37. Detach the bluetooth module from the upper case.
65 Chapter 3
38. Disconnect the click-button cable then remove it.
39. Disconnect the cable linking the click buttons and touchpad then remove it.
40. Remove the three screws fastening the click-button bracket then detach the click-button bracket.
41. Remove the four screws fastening the touchpad bracket then detach the touchpad bracket.
42. Then detach the touchpad.
43. Finally, remove the three screws securing the LED board then detach the LED board from the middle cover.
Chapter 3 66
Disassembling the LCD Module
1. Detach the six LCD screw rubber cushions and remove the six screws fastening the LCD bezel.
2. Then carefully detach the LCD bezel.
3. Detach inverter board then disconnect the LCD backlight cable and the inverter cable.
4. Remove the four screws securing the LCD bracket.
5. Disconnect the CCD module.
6. Detach the LCD.
67 Chapter 3
7. Remove the two screws fastening the LCD right bracket and detach the bracket.
8. Remove the two screws fastening the LCD left bracket and detach the bracket.
9. Carefully detach the tapes then disconnect the LCD cable.
10. Remove the two screws fastening the antenna set.
11. Then carefully detach the antenna set from the LCD panel.
12. Remove the two screws fastening the LCD panel latch.
13. Take out the left LCD panel latch lock with tweezers.
14. Take out the right LCD panel latch lock with tweezers.
15. Then remove the latch.
Chapter 3 68
16. Remove the screw fastening the CCD module.
17. Detach the CCD module carefully from the LCD panel.
Disassembling the ODD Module
1. Remove the four screws fastening the ODD holder and detach the ODD holder.
2. Insert a screwdriver or a clip into the emergency eject hole to eject the optical disk drive as shown
3. Then detach the ODD bezel.
69 Chapter 3
Disassembling the CCD Module
1. Detach the CCD module holder.
2. Separate the cases of the CCD module.
3. Remove the two screws fastening the CCD board and detach the CCD board.
Disassembling the HDD Module
1. Remove the two screws securing the HDD bracket and detach the HDD bracket.
Chapter 3 70
Chapter 4
Troubleshooting
Please use the following procedures as a guide for computer problems.
Note: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options may occur errors or invalid responses.
1. Obtain the detailed fail symptoms as many as possible.
2. Verify the symptoms by attempting to recreate, running the diagnostic tests or repeating the same operation.
Chapter 4 71
System Check Procedures
External Diskette Drive Check
Do the following procedures to isolate the possible effects from a controller, driver, or diskette. A writable, diagnostic diskette is required.
Note: Make sure that the diskette does not have more than one label attached. Multiple labels may cause damage to the drive or make the drive fail.
1. Boot from the diagnostic diskette and start the diagnostic programs.
2. See if FDD test is passed as the programs run the FDD test.
3. Follow the instructions in the message window.
If errors occur with the internal diskette driver, reconnect the diskette connector on the system board. If the errors still remain:
1. Reconnect the external diskette drive.
2. Replace the external diskette driver.
3. Replace the main board.
External CD-ROM Drive Check
Do the following procedures to isolate the possible effects from a controller, driver, or CD-ROM.
Note: Make sure that the CD-ROM does not have any label attached. The label may cause damage to the drive or make the drive fail.
1. Boot from the diagnostic diskette and start the diagnostic programs.
2. See if CD-ROM test is passed when the programs run the CD-ROM test.
3. Follow the instructions in the message window.
If errors occur, reconnect the connector on the system board. If the errors still remain:
1. Reconnect the external CD-ROM drive.
2. Replace the external CD-ROM drive.
3. Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is under test. If the internal keyboard does not work or an unexpected error appears, make sure that the flexible cable extending from the internal keyboard is correctly connected on the system board. If the keyboard is correctly connected, run the Keyboard test.
If errors occur, do the following procedures in sequence to correct the problems. Do not replace a non-defective
FRU.
1. Reconnect the keyboard cable.
2. Replace the keyboard.
3. Replace the main board.
The following auxiliary input devices are supported by this computer.
T
T
Numeric keypad
External keyboard
If any of these devices do not function, reconnect the cable and repeat the anterior procedures.
Memory Check
Follow the procedures below to correct the memory errors.
1. Boot from the diagnostic diskette and start the diagnostic programs.
2. Go to the diagnostic memory in the test items.
72 Chapter 4
3. Press F2 in the test items.
4. Follow the instructions in the message window.
Note: Make sure that the DIMM is correctly inserted into the connector. A wrong connection will cause errors.
Power System Check
To verify the symptoms, power on the computer by using the following power sources separately.
1. Remove the battery pack.
2. Connect the power adaptor and check the power supply.
3. Disconnect the power adaptor and install the battery pack, then check the power supply.
If you think there is a power supply problem, please go to “Check the Power Adaptor” and “Check the Battery
Pack” in this chapter.
Check the Power Adaptor
Unplug the power adaptor cable from the computer and measure the output voltage at the plug of the power adaptor cable. See the illustration and follow the procedures below.
pin 1: +19V to +20.5V
pin 2: 0V, ground
1. If the voltage is not correct, replace the power adaptor.
2. If the voltage is within the range:
(1) Replace the system board.
(2) If the problem is still not resolved, see “Undetermined Problems”.
(3) If the voltage is not correct, go to the next step.
Note: An audible noise from the power adaptor does not always indicate a defect.
3. If the power-on indicator does not light up, check the power cord of the power adaptor for continuity and correct installation.
4. If the operational charge does not work, see “Check the Battery Pack”.
Check the Battery Pack
Follow the procedures below to check the battery pack.
From software, this helps to identify the problem is on recharging or discharging.
1. Check the Power Management in Control Panel.
2. Then confirm that the parameters shown in the screen for Current Power Source and Total Battery Power
Remaining are correct.
3. Repeat the step 1 and step 2 for both battery and adaptor.
From hardware, this helps to identify whether you should replace the battery pack or not.
1. Power off the system.
2. Remove the battery pack and measure the voltage between terminals one (+) and seven (-). There are seven terminals totally. See the illustration below.
Chapter 4 73
3. If the voltage is still less than 7.5V after recharging, replace the battery.
If the battery status indicator does not light up, remove the battery pack. After the battery pack returns to room temperature, reinstall it to the system.
If the charge indicator does not light up, replace the battery pack. If the charge indicator still does not light up, replace the AC/DC charger board.
Touchpad Check
If the touchpad does not work, follow the procedures one at a time to correct the problem. Do not replace a nondefective FRU.
1. Reconnect the touchpad cables.
2. Replace the touchpad.
3. Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement will occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware problem.
74 Chapter 4
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes.
Note: Perform the FRU replacement or actions in the sequence shown in Error Message List, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU.
The error messages are listed in the coming pages to indicate the BIOS signals on the screen and the error symptoms classified by functions. If the symptom is not included on the list, please refer to “Undetermined
Problems”.
Note: Most of the error messages occur during POST. Some of them show information about a hardware device, for example, the size of memory installed. Others may indicate problems with a device, such as the way it has been configured.
Note: If the system fails after you make changes in the BIOS Setup Utility menus, please reset the computer.
Enter Setup and install Setup defaults to correct the errors.
Index of Error Messages
006
Error Code
010
070
071
072
110
No error code
No error code
Error Message
Equipment Configuration Error Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
The causes will be shown before “Equipment Configuration Error”.
Memory Error at xxxx:xxxx:xxxxh (R: xxxxh, W: xxxxh)
Real Time Clock Error
CMOS Battery Bad
CMOS Checksum Error
System disabled.
Incorrect password is specified.
Battery critical low: In this situation BIOS will issue four short beeps then shut down system, no message will be shown.
Thermal critical high: In this situation BIOS will shut down the system, no message will be shown.
Error Message
Failure Fixed Disk
Stuck Key
Keyboard error
Keyboard Controller Failed
Keyboard locked - Unlock key switch
Monitor type does not match
CMOS - Run Setup
Shadow RAM Failed at offset: nnnn
FRU/Action in Sequence
Reconnect hard disk drive connector.
Run “Load Default Settings” in BIOS Setup Utility.
Hard disk drive
System board see ”Keyboard or Auxiliary Input Device Check”. see ”Keyboard or Auxiliary Input Device Check”. see ”Keyboard or Auxiliary Input Device Check”.
Unlock external keyboard
Run “Load Default Settings” in BIOS Setup Utility.
BIOS ROM
System board
Chapter 4 75
76
Error Message
System RAM Failed at offset: nnnn
Extended RAM Failed at offset: nnnn
System battery is dead -
Replace and run Setup
System CMOS checksum bad -
Default configuration used
System timer error
Real time clock error
Previous boot incomplete -
Default configuration used
Memory size found by POST differed from CMOS
Diskette drive A error
Incorrect Drive A type - run
Setup
System cache error - Cache disabled
CPU ID:
DMA Test Failed
Software NMI Failed
Fail-Safe Timer NMI Failed
Device Address Conflict
Allocation Error for device
Failing Bits: nnnn
Fixed Disk n
Invalid System Configuration
Data
FRU/Action in Sequence
DIMM
System board
DIMM
System board
Replace RTC battery and Run BIOS Setup Utility to reconfigure system time, then reboot system.
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot system.
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot system.
System board
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot system.
System board
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Run “Load Default Settings” in BIOS Setup Utility.
DIMM
System board
Check the drive is defined with the proper diskette type in BIOS Setup Utility.
See “External Diskette Drive Check”.
Check the drive is defined with the proper diskette type in BIOS Setup Utility.
System board
System board
DIMM
System board
DIMM
System board
DIMM
System board
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
DIMM
BIOS ROM
System board
None
BIOS ROM
System board
Chapter 4
Error Message
I/O device IRQ conflict
Operating system not found
No beep, power-on indicator turns off and LCD is blank.
No beep, power-on indicator turns on and LCD is blank.
No beep, power-on indicator turns on and LCD is blank. But you can see POST on an external CRT.
No beep, power-on indicator turns on and a blinking cursor shown on LCD during POST.
No beep during POST but system runs correctly.
FRU/Action in Sequence
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Enter Setup and see if fixed disk and drive A: are properly identified.
Diskette drive
Hard disk drive
System board
Power source (battery pack and power adapter). See
“Power System Check”.
Ensure every connector is connected correctly.
Reconnect the DIMM.
LED board
System board
Power source (battery pack and power adapter). See
“Power System Check”.
Reconnect the LCD connector.
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
Reconnect the LCD connectors.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Ensure every connector is connected tightly and correctly.
System board
Speaker
System board
Chapter 4 77
POST Code
E7h
E8h
E9h
EAh
EBh
ECh
EDh
EEh
E0h
E1h
E2h
E3h
E4h
E5h
E6h
F3h
F4h
F5h
F6h
F7h
EFh
F0h
F1h
F2h
Code
1
Beeps For Boot Block in Flash ROM
Initialize the chipset.
Initialize the bridge.
Initialize the CPU.
Initialize the system timer.
Initialize system I/O.
Check force recovery boot.
Checksum BIOS ROM.
Go to BIOS.
Set Huge Segment.
Initialize Multi Processor.
Initialize OEM special code.
Initialize PIC and DMA.
Initialize Memory type.
Initialize Memory size.
Shadow Boot Block.
System memory test.
Initialize interrupt vectors.
Initialize Run Time Clock.
Initialize video.
Initialize System Management Mode.
Output one beep before boot.
Boot to Mini DOS.
Clear Huge Segment.
Boot to Full DOS.
78 Chapter 4
Index of Symptom-to-FRU Error Message
Symptom/Error
LCD backlight doesn't work.
LCD is too dark.
LCD brightness cannot be adjusted.
LCD contrast cannot be adjusted.
Unreadable LCD screen
Missing pels in characters
Abnormal screen
Wrong color displayed
LCD has extra horizontal or vertical lines displayed.
Action in Sequence
Enter BIOS Utility to execute “Load Setup Default
Settings”, then reboot system.
Reconnect the LCD connectors.
Keyboard (if contrast and brightness function key do not work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Reconnect the LCD connector.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Symptom/Error
Indicator incorrectly remains off or on, but system runs correctly.
Action in Sequence
Reconnect the inverter board
Inverter board
System board
Symptom/Error
Power shuts down during operation.
The system doesn’t power on.
The system doesn’t power-off.
Battery can’t be charged.
Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check”.
Battery pack
Power adapter
Hard drive & battery connection board
System board
Power source (battery pack and power adapter). See “Power
System Check”.
Battery pack
Power adapter
Hard drive & battery connection board
System board
Power source (battery pack and power adapter). See Power
System Check”.
Hold and press the power switch for more than 4 seconds.
System board
See “Check the Battery Pack”.
Battery pack
System board
Chapter 4 79
80
Symptom/Error
System cannot detect the
PC Card (PCMCIA).
PCMCIA slot pin is damaged.
Action in Sequence
PCMCIA slot assembly
System board
PCMCIA slot assembly
Symptom / Error
Memory count (size) appears different from actual size.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings, then reboot system.
DIMM
System board
Action in Sequence Symptom/Error
In Windows, multimedia programs, no sound comes from the computer.
Internal speakers make noise or emit no sound.
Audio driver
Speaker
System board
Speaker
System board
Symptom/Error
The system will not enter hibernation.
The system does not enter hibernation mode and four short beeps every minute.
The system does not enter standby mode after closing the LCD.
The system does not resume from hibernation mode.
The system does not resume from standby mode after opening the
LCD.
Battery fuel gauge in
Windows does not go higher than 90%.
System hangs intermittently.
Action in Sequence
Keyboard (if control is from the keyboard)
Hard disk drive
System board
Press Fn + F4 and see if the computer enters hibernation mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
LCD cover switch
System board
Hard disk connection board
Hard disk drive
System board
LCD cover switch
System board
Remove battery pack and let it cool for two hours.
Refresh battery (continue to use battery until power off, then charge battery).
Battery pack
System board
Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board
Chapter 4
Symptom/Error
System configuration does not match the installed devices.
External display does not work correctly.
USB does not work correctly.
Print problems
Serial or parallel port device problems.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings”, then reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
Press Fn + F5, LCD/CRT/Both display switching
System board
System board
Ensure the “Parallel Port” in the “Onboard Devices
Configuration” of BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Ensure the “Serial Port” in the Devices Configuration” of BIOS
Setup Utility is set to Enabled.
Device driver
Device cable
Device
System board
Symptom/Error
Keyboard (one or more keys) does not work.
Touchpad does not work.
Action in Sequence
Reconnect the keyboard cable.
Keyboard
System board
Reconnect touchpad cable.
Touchpad board
System board
Symptom/Error
Internal modem does not work correctly.
Modem phone port modem combo board
System board
Action in Sequence
Note: If you can not correct the problems according to the anterior tables, see “Undetermined Problems”.
Chapter 4 81
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists.
When analyzing an intermittent problems, follow the procedures below:
1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRU.
3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
82 Chapter 4
Undetermined Problems
The diagnostic problems does not identify which devices fail, which devices are incorrectly installed, whether a short circuit happens, or whether the system is inoperative.
Note: Verify if all devices attached are supported by the computer.
Note: Verify if the power supply used at the time of failure is operating correctly. You can refer to “Power
System Check”.
Follow the procedures below to isolate the failing FRU. Do not isolate non-defective FRU.
1. Power off the computer.
2. Visually check the devices. If any problems are found, replace the FRU.
3. Remove or disconnect all of the following devices:
•
Non-Acer devices
•
Printer, mouse, and other external devices
•
Battery Pack
•
Hard disk drive
•
DIMM
•
CD-ROM / Diskette drive module
•
PC cards
4. Power on the computer.
5. Determine if the problem has been resolved.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failed FRU.
7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU.
•
System board
•
LCD assembly
Chapter 4 83
Jumper and Connector Locations
Top View of Main Board
Chapter 5
Chapter 5 84
Part One of Top View
Part Two of Top View
85 Chapter 5
Part Three of Top View
Chapter 5
CN24
CN25
CN26
CN28
CN29
CN30
CN31
Item
CN20
CN21
CN22
CN23
SVIDEO
Description
Docking
DVI-D
CRT connector mini card connector
RJ45 W/ LED
Battery connector (seven pin)
Fan connector
Media connector (M/B side)
DDR2 (9.2MM)
DDR2 (5.2MM)
U37
U40
U41
U43
U44
U48
U57
Item
CN32
CN33
CN37
CN38
Description
RTC battery connector (two pin)
HDD connector (22 pin
SATA)
Connector SMD FFC 30 pin
Bluetooth module connector
(five pin)
V-RAM
V-RAM
VGA chip
CPU
North bridge
South bridge
BIOS
86
Bottom View
Part One of Bottom View
87 Chapter 5
Part Two of Bottom View
Part Three of Bottom View
CN06
CN07
CN08
CN09
CN10
CN12
CN14
Item
CN02
CN03
CN04
CN05
Chapter 5
Description
Mic connector (two pin)
Main board to button board
FFC connector (16 pin)
LCD connector (40 pin) daughter board cable to main board (10 pin)
Keyboard FFC connector
(25 pin)
Touchpad FFC connector
(four pin)
USB
USB
Smart card FFC connector
PCMCIA card header
Five-in-one card reader
Item
CN15
CN16
CN17
CN18
CN19
U06
U10
U28
SW02
SW03
Description
Speaker connector (four pin)
1394 (four pin)
SPDIF (line out)
Audio jack/line in
Audio jack/mic
V-RAM
V-RAM
IR module
Slider switch
Slider switch
88
Chapter 6
FRU (Field Replaceable Unit) List
This chapter offers the FRU (Field Replaceable Unit) list in global configuration of Travelmate 8210/ 8200 series.
Refer to this chapter whenever ordering the parts to repair or for RMA (Return Merchandise Authorization).
Please note that when ordering FRU parts, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number is changed, it will NOT be noted on the printed service guide. For Acer authorized service providers, your Acer office may have a different part number code from those given in the FRU list of this printed service guide. You MUST use the local FRU list provided by your regional
Acer office to order FRU parts for service.
Note: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to dispose them properly, or follow the rules set by your regional Acer office on how to return it.
Chapter 6 89
Exploded Diagram
90 Chapter 6
Parts
CATEGORY
ADAPTER
N/A
BOARD
PARTNAME
MODEM BOARD 56K (MDC)
T60M893.T00 S/P
DESCRIPTION
ZF1 MODEM 56K (MDC)
T60M893.T00 S/P
ACER PART NO.
ADAPTER 90W 3 PIN LITEON PA-
1900-04QB ROHS
ADAPTER 90W 3 PIN DELTA ADP-
90SB BBAHF ROHS
BATTERY SANYO LI-ION COMO 9
CELL 2.6
BATTERY PANASONIC LI-ION
COMO 9 CELL 2.6
PRISMATIC COMO 2ND 6 CELL
1.9 P SANYO PACK 3800MAH
ZC1 ADAPTER LITEON S/P
ZC1 ADAPTER DELTA S/P
AP.09003.009
AP.09001.005
ZC1 BATTERY SANYO 9
CELL S/P
ZC1 BATTERY PANASONIC 9
CELL S/P
ZC1 2ND BATTERY SANYO 6
CELL S/P
BT.00903.005
BT.00905.001
BT.00603.015
54.T72V7.001
BLUETOOTH MODULE
FOXCONN T60H928.01 W/
ANTENNA
MINI PCI WIRELESS BOARD
802.11 A/B/G MOW2 INTEL
MM872659
MINI PCI WIRELESS BOARD
802.11 A/B/G MOW1 INTEL
MM872612
MINI PCI WIRELESS BOARD
802.11 A/B/G ROW INTEL
MM874511
TOUCHPAD BOARD
POWER BOARD
BUTTON BOARD
USB BOARD
ZC1 FOX BULETOOTH
(T60H928.01) S/P
54.TAXV7.001
ZC1 W/L 3945ABG MOW2 S/P KI.GLN01.002
ZC1 W/L 3945ABG MOW1 S/P KI.GLN01.001
ZC1 W/L 3945ABG ROW S/P KI.GLN01.003
ZC1 TOUCHPAD BOARD
ASSY S/P
55.TAXV7.001
ZC1 POWER BOARD ASSY
S/P
55.TAXV7.002
ZC1 BUTTON BOARD ASSY
S/P
55.TAXV7.003
ZC1 USB BOARD ASSY S/P 55.TAXV7.004
LCD INVERTER BOARD W/ TYPE ZF1 INV (8-20V, V=700,
REV=A1A) S.P.
OPTICAL DEVICE CONNECTOR
BOARD
ZC1 CD ROM BOARD ASSY
S/P
19.TAXV7.001
55.TAXV7.005
Chapter 6 91
CABLE
N/A
92
POWER CORD US 3 PIN ROHS
POWER CORD EU 3 PIN ROHS
POWER CORD UK 3 PIN ROHS
POWER CORD ITALIAN 3 PIN
ROHS
POWER CORD DANISH 3 PIN
ROHS
POWER CORD SWISS 3 PIN
ROHS
POWER CORD PRC 3 PIN ROHS
POWER CORD US-110V (BSMI)
ROHS
POWER CORD AU W/ LABEL 3
PIN ROHS
POWER CORD AF 3 PIN ROHS
POWER CORD AF-S INDIA ROHS
POWER CORD KOREA 2 PIN
ROHS
POWER CORD JAPAN ROHS
POWER CORD ISRAEL 3 PIN
ROHS
POWER CORD US 3 PIN
POWER CORD EU
POWER CORD UK
ZB1 PWR CORD US S/P
ZB1 PWR CORD (CEE) S/P
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
POWER CORD CONTINENTAL
POWER CORD ISRAEL
POWER CORD ITALIAN
POWER CORD SWISS
POWER CORD US-110V (BSMI)
POWER CORD AF 3 PIN
POWER CORD DANISH 3 PIN
POWER CORD AUSTRALIA W/
LABEL
POWER CORD SOUTH AFRICA-S
(INDIA)
POWER CORD US-110V
POWER CORD JAPAN
POWER CORD PRC 3 PIN
MODEM CABLE
ET2S POWER CORD S/P US
ZC1 POWER CORD EU S/P
ET2S POWER CORD SPARE
PART UK
EI2 POWER CORD 3P
CONTINENTAL S.P.
ZL6A POWER CORD S/P ISR
S.P.
EI2 POWER CORD 3P ITALY
S.P.
ZE1 POWER CORD 3P
SWISS S.P.
ZL3E POWER CORD S/P
TWN
ZI5 POWER CORD S/P AF
ET2S POWER CORD S/P
DANISH
ZL6A POWER CORD S/P AU
S.P.
ZL6A POWER CORD S/P
INDIA S.P.
ZL3E POWER CORD S/P
THAI
TBD
ET2S POWER CORD S/P
PRC
ZC1 CABLE MDC (2/2P,
REV1A) S/P
27.A03V7.001
TBD
TBD
TBD
TBD
TBD
TBD
TBD
27.T48V7.001
27.A03V7.006
TBD
TBD
TBD
TBD
27.A03V7.003
50.TAXV7.001
FFC CABLE TOUCHPAD BOARD
TO MAIN BOARD LF
ZC1 CABLE MB TP/B
(122.5MM, 4/4, 2A) S/P
50.TAXV7.002
Chapter 6
N/A
FFC CABLE BUTTON BOARD TO
MAINBOARD LF
ZC1 CABLE BUTTON BOARD
(60MM, 16/16, 2A) S/P
50.TAXV7.003
FFC CABLE - TP/B TO TP LF
USB CABLE - 10/10P
USB CABLE - 4/4P
ZC1 CABLE TP/B TO TP
(76MM, 12/12, 2A) S/P
ZC1 CABLE USB (10/10P,
REV1A) S/P
TBD
50.TAXV7.004
50.TAXV7.005
50.TAXV7.006
LCD CABLE 15.4 IN. WXGA ZC1 CABLE 15" SXGA + ID5
(40/40P R1A) S/P
50.TAXV7.007
N/A DCIN CABLE
CASE / COVER / BRACKET ASSEMBLY
MIDDLE COVER
UPPER CASE W/ TP
ZC1 CABLE DCIN (5/5P,
REV1A) S/P
ZC1 KB COVER ASSY S/P
ZC1 TOP ASSY S/P
TBD
42.TAXV7.001
60.TAXV7.001
N/A
LOWER CASE W/ SPEAKER ZC1 BASE CASE ASSY S/P 60.TAXV7.002
THERMAL DOOR
TP BOARD SUPPORT BRACKET
ZC1 THERMAL DOOR ASSY
S/P
42.TAXV7.002
ZC1 TP BD SUPPORT
BRACKET S/P
33.TAXV7.001
DUMMY-NEW CARD
OPTICAL DEVICE HOLDER
ZC1 DUMMY-NEW-CARD S/P
ZC1 ODD-HOLDER S/P
42.TAXV7.003
42.TAXV7.006
SUPER MULTI G BASE BEZEL
HDD BRACKET
ZC1 SUPER MULTI BEZEL
ASSY S/P
ZC1 HDD BRACKET S/P
42.TAXV7.007
33.TAXV7.002
Chapter 6 93
HDD DOOR ZC1 HDD DOOR ASSY S/P 42.TAXV7.004
LCD PANEL CARBON 15.4 IN. W/
LOGO ANTENNA CCD MODULE
ZC1 15.4 LCD COVER Carbon
ASSY S/P
60.TAXV7.004
LCD BEZEL W/ RUBBER PAD 15.4
IN.
ZC1 15.4 LCD BEZEL ASSY
S/P
60.TAXV7.005
LCD BRACKET W/HINGE 15.4 IN.
- L
ZC1 HINGE-L S/P 33.TAXV7.004
LCD BRACKET W/HINGE 15.4 IN.
- R
ZC1 HINGE-R S/P 33.TAXV7.005
N/A
N/A
N/A
N/A
2ND HDD BRACKET
2ND HDD COVER ZC1
(EBZC1027, REV3A) LF
COMMUNICATION MODULE
N/A WIRELESS LAN ANTENNA
CPU
PCMCIA SLOT
2ND HDD BASE ASSY
CPU INTEL YONAH CORE DUO
FSB-667 2.16G 2M L8VN
CPU INTEL YONAH CORE DUO
FSB-667 2.0G 2M L8VP
CPU INTEL YONAH CORE DUO
FSB-667 1.83G 2M L8VQ
CPU INTEL YONAH CORE DUO
FSB-667 1.66G 2M L8VR
ZF1 PCMCIA SLOT ASSY S.P
ZC1 2ND HDD BASE ASSY S/
P
ZL1 2ND BRACKET ASSY S/P
ZC1 2ND HDD COVER S/P
22.T72V7.001
60.TAXV7.003
33.TAXV7.003
42.TAXV7.005
ZC1 ANTENNA
(81.ED415.009) S/P
50.TAXV7.011
ZC1 Intel CPU YONAH 2.16G
S/P
ZC1 Intel CPU YONAH 2.0G
S/P
ZC1 Intel CPU YONAH 1.83G
S/P
ZC1 Intel CPU YONAH 1.66G
S/P
KC.26001.DTP
KC.25001.DTP
KC.24001.DTP
KC.23001.DTP
DVD RW DRIVE
94 Chapter 6
HDD
KEYBOARD
DVD SUPER MULTI HLDS GSA-
4082N
DVD SUPER MULTI DRIVE HLDS
GSA-4082N DL G BASE
DVD SUPER MULTI PAN UJ-850
DVD SUPER MULTI UJ-850BAA-A
FW1.5
ZC1 SUPER MULTI HLDS
GSA-4082N ASSY S/P
ZF1A SUPER MULTI (HLDS
GSA-4082N) S/P
ZC1 DVD SUPERMUTI PAN
UJ850 ASSY S/P
ZC1 DVD SUPERMUTI PAN
UJ850 S/P
HDD 80GB 2.5 IN. SEGATE
MERCURY2 ST98823AS FW:3.06
LF
HDD 100GB 2.5 IN. SEGATE
MERCURY2 ST9100824AS
FW:3.06 LF
HDD 120GB 2.5 IN. SEGATE
MERCURY2 ST9120821AS
FW:3.06 LF
ZC1 HDD Seagate 80G S/P
ZC1 HDD Seagate 100G S/P
ZC1 HDD Seagate 120G S/P
6M.TAXV7.001
KU.0080D.017
6M.TAXV7.002
KU.00807.025
KH.08001.023
KH.10001.008
KH.12001.025
TM8200 KEYBOARD DARFON US
INTERNATIONAL
TM8200 KEYBOARD DARFON
CHINESE
TM8200 KEYBOARD DARFON
SPANISH
TM8200 KEYBOARD DARFON
THAI
TM8200 KEYBOARD DARFON
BRAZILIAN PROTUGESE
TM8200 KEYBOARD DARFON
KOREA
TM8200 KEYBOARD DARFON UK
ZC1 K/B MODULE (UI) S/P
ZC1 K/B MODULE (TAIWAN)
S/P
ZC1 K/B MODULE (SPANISH)
S/P
ZC1 K/B MODULE (THAI) S/P
ZC1 K/B MODULE (BRAZIL)
S/P
ZC1 K/B MODULE (KOREAN)
S/P
ZC1 K/B MODULE (UK) S/P
KB.TAX07.001
KB.TAX07.002
KB.TAX07.003
KB.TAX07.004
KB.TAX07.005
KB.TAX07.006
KB.TAX07.007
Chapter 6 95
96
TM8200 KEYBOARD DARFON
GERMAN
TM8200 KEYBOARD DARFON
ITALIAN
TM8200 KEYBOARD DARFON
FRENCH
TM8200 KEYBOARD DARFON
SWISS/G
TM8200 KEYBOARD DARFON
PORTUGUESE
TM8200 KEYBOARD DARFON
ARABIC
TM8200 KEYBOARD DARFON
BELGIUM
TM8200 KEYBOARD DARFON
SWEDEN
TM8200 KEYBOARD DARFON
CZECH
TM8200 KEYBOARD DARFON
HUNGAIAN
TM8200 KEYBOARD DARFON
NORWAY
TM8200 KEYBOARD DARFON
DANISH
TM8200 KEYBOARD DARFON
TURKISH
TM8200 KEYBOARD DARFON
CANADIAN FRENCH
TM8200 KEYBOARD DARFON
JAPANESE
TM8200 KEYBOARD DARFON
GREEK
TM8200 KEYBOARD DARFON
HEBREW
TM8200 KEYBOARD DARFON
RUSSIAN
TM8200 KEYBOARD DARFON
SLOVENIA (SLO)
TM8200 KEYBOARD DARFON
CROATIA (CR)
TM8200 K/B MODULE FARSI
TM8200 K/B MODULE
BULGARIAN
TM8200 K/B MODULE POLAND
TM8200 K/B MODULE CHINA
TM8200 K/B MODULE DUTCH
TM8200 K/B MODULE LA
TM8200 K/B MODULE ICELAND
TM8200 K/B MODULE US
ZC1 K/B MODULE (GERMAN)
S/P
ZC1 K/B MODULE (ITALIAN)
S/P
ZC1 K/B MODULE (FRENCH)
S/P
ZC1 K/B MODULE (SWISS) S/
P
ZC1 K/B MODULE
(PORTUGUESE) S/P
ZC1 K/B MODULE (ARAB-EN)
S/P
ZC1 K/B MODULE (BELGIUM)
S/P
ZC1 K/B MODULE
(SWEDISH) S/P
ZC1 K/B MODULE (CZECH)
S/P
ZC1 K/B MODULE
(HUNGARIAN) S/P
ZC1 K/B MODULE
(NORWEGIAN) S/P
ZC1 K/B MODULE (DANISH)
S/P
ZC1 K/B MODULE (TURKISH)
S/P
ZC1 K/B MODULE (FRA-CAN)
S/P
ZC1 K/B MODULE (JA) S/P
KB.TAX07.008
KB.TAX07.009
KB.TAX07.010
KB.TAX07.011
KB.TAX07.012
KB.TAX07.013
KB.TAX07.014
KB.TAX07.015
KB.TAX07.016
KB.TAX07.017
KB.TAX07.018
KB.TAX07.019
KB.TAX07.020
KB.TAX07.021
KB.TAX07.022
ZC1 K/B MODULE (GREEK)
S/P
ZC1 K/B MODULE (HEBREW)
S/P
ZC1 K/B MODULE (RUSSIAN)
S/P
ZC1 K/B MODULE (SLOVAK)
S/P
ZC1 K/B MODULE
(CROATIAN) S/P
ZC1 K/B MODULE (FARSI) S/
P
ZC1 K/B MODULE
(BULGARIAN) S/P
ZC1 K/B MODULE (POLAND)
S/P
ZC1 K/B MODULE (CHINA) S/
P
ZC1 K/B MODULE (DUTCH)
S/P
ZC1 K/B MODULE (LA) S/P
ZC1 K/B MODULE (ICELAND)
S/P
ZC1 K/B MODULE (US) S/P
KB.TAX07.023
KB.TAX07.024
KB.TAX07.025
KB.TAX07.026
KB.TAX07.027
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
Chapter 6
LCD
MEMORY
MAIN BOARD
LCD MODULE 15.4 IN. CARBON
ASSY W/ ANTENNA CCD
LCD MODULE 15.4 IN. COATING
ASSY W/ ANTENNA CCD
LCD 15.4 IN. WSXGA+ QDI
QD15AL02-01 NON GLARE LF
LCD 15.4 IN.WSXGA+ CMO
N154Z1-L01 NON GLARE LF
LCD 15.4 IN. WSXGA+ SAMSUNG
LTN154P1-L02-V NON GLARE LF
ZC1 LCD QDI (15.4WSXGA+)
CARBON S/P
ZC1 LCD QDI (15.4WSXGA+)
Pre. S/P
ZC1 15.4 (WSXGA+)
QD15AL02 S/P
ZC1 LCD15.4 WSXGA +
(N154Z1-L01) S/P
ZC1 LCD15.4 WSXGA +
LTN154P1-L02-V S/P
6M.TAXV7.003
6M.TAXV7.004
LK.15409.014
LK.1540D.009
LK.15406.008
HYNIX SO-DIMM DDRII 533
512MB HYMP564S64P6-C4
INFINEON SO-DIMM DDRII 533
512MB HYS64T64020HDL-3.7-A
LF (0.11U)
NANYA SO-DIMM DDRII533
512MB NT512T64UH8A1FN-37B
LF
SAMSUNG SO-DIMM DDRII533
512MB M470T6554CZ3-CD500 LF
NANYA SO-DIMM DDRII667
512MB NT512T64UH8A1FN-3C LF
NANYA SO-DIMM DDRII533 1GB
NT1GT64UH8A0BN-37B LF
INFINEON SO-DIMM DDRII533
1GB HYS64T128021HDL-3.7-A LF
(0.11u)
NANYA SO-DIMM DDRII667 1GB
NT1GT64U8HA0BN-3C LF
ELPIDA SO-DIMM DDRII533
512MB GU33512AGEPN612C
ZC1 HYNIX DDRII 533 512MB
RAM S/P
ZC1 INFINEON DDRII 533
512MB RAM S/P
ZC1 NANYA DDRII533 512MB
RAM S/P
KN.51203.023
ZC1 SAMSUNG DDRII533
512MB RAM S/P
ZC1 NANYA DDRII667 512MB
RAM S/P
ZC1 NANYA DDRII533 1GB
RAM S/P
SO-DIMM DDRII533 1GB
HYS64T128021HDL-3.7-A LF
(0.11u)
SO-DIMM DDRII667 1GB
NT1GT64U8HA0BN-3C LF
SO-DIMM DDRII533 512MB
GU33512AGEPN612C
KN.5120G.005
KN.51202.021
KN.5120B.015
KN.51203.025
KN.1GB03.006
KN.1GB02.023
KN.1GB03.009
KN.51209.005
MAINBOARD 945PM M56P256MB
SATA W/READER, NEW CARD W/
O CPU MEMORY
ZC1 M/B ASSY S/P MB.TAX06.001
HEATSINK
THERMAL MODULE ZC1 THERMAL MODULE
ASSY S/P
60.TAXV7.007
SPEAKER
N/A
READER
SPEAKER
SMART CARD READER
ZC1 SPEAKER
PB2510KN04S-9LB S/P
ZC1 SMART CARD S/P
23.TAXV7.001
60.TAXV7.008
Chapter 6 97
MISCELLANEOUS
N/A
SCREWS
N/A
LCD-RUBBER-PAD1-
ZC1(GAZC1002,REV3A)LF
LCD-RUBBER-L-
ZC1(GAZC1003,REV3A)LF
LCD-RUBBER-R-
ZC1(GAZC1004,REV3A)LF
CARD-READER-RUBBER-
ZC1(EBZC1040,REV3A)LF
RUBBER FOOT
SCREW M2.0*2.5-I (NI) (NYLOK)
SCREW M2.5*6-I (BNI) (NYLOK)
SCREW M2.0*3.0-I-NI-NYLOK
SCREW M2.0*6.0-I-NI-NYLOK
SCREW M2.5*2-I (NI, NYLOK)
SCREW M2.5*3-I (NI, NYLOK)
SCREW M2.5*6-I (BNI) TAP
SCREW M2.5*4-I (BNI)
SCREW M2.5*4.0-I (NYLOK) EU
ZC1 LCD-RUBBER-PAD1 S/P
ZC1 LCD-RUBBER-L S/P
ZC1 LCD-RUBBER-R S/P
ZC1 CARD READER
RUBBER S/P
ZC1 RUBBER FOOT S/P
47.TAXV7.001
47.TAXV7.002
47.TAXV7.003
47.TAXV7.004
47.TAXV7.005
ET2S SCREW MM2.0X3.0
SPARE PART
ZG1S I2.5*3M-BNIH(M2.5L3)
S/P
ZI1S SCREW M2.0X5-I-NI-
NYLOK S/P
DT1 SCREW MM25060IL69
SPARE PART
ZI1S SCREW M2.5X2-I-NI-
NYLOK S/P
ET2S SCREW MM2.5X3.0
SPARE PART
ZC1 SCREW M2.5*6-
I(BNI)TAP S/P
ZI1S SCREW M2.5X4-I-BNI S/
P
ZI1S SCREW M2.5X4-I-
NYLOK S/P
86.A03V7.012
86.T25V7.012
86.T23V7.006
86.A08V7.004
86.T23V7.018
86.A03V7.010
86.TAXV7.001
86.T23V7.019
86.T23V7.009
98 Chapter 6
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- - 1.6GHz Intel Core 2 Duo processor for fast and efficient performance
- - 1GB of DDR2 memory for smooth multitasking
- - 80GB hard drive for ample storage space
- - 15.4-inch widescreen display for a clear and vibrant viewing experience
- - Built-in webcam and microphone for easy video conferencing
- - Long battery life for up to 5 hours of use on a single charge
- - Lightweight and portable design for easy carrying