Alpine IVA D310 - DVD Player With LCD Monitor Owner`s manual

PHONES
(044) 360-7-130
(050) 336-0-130
(063) 788-0-130
(067) 233-0-130
(068) 282-0-130
Internet store of
autogoods
ICQ
294-0-130
597-0-130
SKYPE
km-130
CAR RECEIVERS — Receivers • Media receivers and stations • Native receivers • CD/DVD changers • FM-modulators/USB adapters • Flash memory • Facia plates and adapters • Antennas • Accessories |
CAR AUDIO — Car audio speakers • Amplifiers • Subwoofers • Processors • Crossovers • Headphones • Accessories | TRIP COMPUTERS — Universal computers • Model computers • Accessories |
GPS NAVIGATORS — Portable GPS • Built-in GPS • GPS modules • GPS trackers • Antennas for GPS navigators • Accessories | VIDEO — DVR • TV sets and monitors • Car TV tuners • Cameras • Videomodules
• Transcoders • Car TV antennas • Accessories | SECURITY SYSTEMS — Car alarms • Bike alarms • Mechanical blockers • Immobilizers • Sensors • Accessories | OPTIC AND LIGHT — Xenon • Bixenon • Lamps
• LED • Stroboscopes • Optic and Headlights • Washers • Light, rain sensors • Accessories | PARKTRONICS AND MIRRORS — Rear parktronics • Front parktronics • Combined parktronics • Rear-view mirrors
• Accessories | HEATING AND COOLING — Seat heaters • Mirrors heaters • Screen-wipers heaters • Engine heaters • Auto-refrigerators • Air conditioning units • Accessories | TUNING — Vibro-isolation
• Noise-isolation • Tint films • Accessories | ACCESSORIES — Radar-detectors • Handsfree, Bluetooth • Windowlifters • Compressors • Beeps, loudspeakers • Measuring instruments • Cleaners • Carsits
• Miscellaneous | MOUNTING — Installation kits • Upholstery • Grilles • Tubes • Cable and wire • Tools • Miscellaneous | POWER — Batteries • Converters • Start-charging equipment • Capacitors
• Accessories | MARINE AUDIO AND ELECTRONICS — Marine receivers • Marine audio speakers • Marine subwoofers • Marine amplifiers • Accessories | CAR CARE PRODUCTS — Additives • Washer fluid •
Care accessories • Car polish • Flavors • Adhesives and sealants | LIQUID AND OIL — Motor oil • Transmission oil • Brake fluid • Antifreeze • Technical lubricant
In store "130" you can find and buy almost all necessary goods for your auto in
Kyiv and other cities, delivery by ground and postal services. Our experienced
consultants will provide you with exhaustive information and help you to chose
the very particular thing. We are waiting for you at the address
http://130.com.ua
01GB01TMEM860.fm
Page 1
Friday, February 24, 2006
10:08 AM
FOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE/PARA USO EN
AUTOMÓVILES/SOLO PER L’UTILIZZO IN AUTOMOBILE/ENDAST FÖR BILBRUK
R
EN
TME-M860
8.0-INCH TOUCH PANEL
WIDE VGA MONITOR
DE
• OWNER'S MANUAL
Please read before using this equipment.
a
.u
FR
• BEDIENUNGSANLEITUNG
Lesen Sie diese Bedienungsanleitung bitte vor
Gebrauch des Gerätes.
m
o
c
.
• MODE D'EMPLOI
Veuillez lire avant d’utiliser cet appareil.
ES
• MANUAL DE OPERACIÓN
Léalo antes de utilizar este equipo.
0
13
• ISTRUZIONI PER L’USO
Si prega di leggere prima di utilizzare l’attrezzatura.
• ANVÄNDARHANDLEDNING
Innan du använder utrustningen bör du läsa igenom
denna användarhandledning.
IT
• 使用手冊
請在使用本設備之前先閱讀使用手冊。
ALPINE ELECTRONICS MARKETING, INC.
1-1-8 Nishi Gotanda,
Shinagawa-ku,
Tokyo 141-0031, Japan
Phone 03-5496-8231
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.
161-165 Princes Highway, Hallam
Victoria 3803, Australia
Phone 03-8787-1200
ALPINE ITALIA S.p.A.
Viale C. Colombo 8, 20090 Trezzano
Sul Naviglio (MI), Italy
Phone 02-484781
ALPINE ELECTRONICS GmbH
Frankfurter Ring 117,
80807 München, Germany
Phone 089-32 42 640
ALPINE ELECTRONICS DE ESPAÑA, S.A.
Portal de Gamarra 36, Pabellón, 32
01013 Vitoria (Alava)-APDO 133, Spain
Phone 945-283588
ALPINE ELECTRONICS OF U.K. LTD.
Alpine House
Fletchamstead Highway, Coventry CV4 9TW, U.K.
Phone 0870-33 33 763
ALPINE ELECTRONICS (BENELUX) GmbH
Leuvensesteenweg 510-B6,
1930 Zaventem, Belgium
Phone 02-725-13 15
ALPINE ELECTRONICS OF AMERICA, INC.
19145 Gramercy Place, Torrance,
California 90501, U.S.A.
Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF CANADA, INC.
777 Supertest Road, Toronto,
Ontario M3J 2M9, Canada
Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS FRANCE S.A.R.L.
(RCS PONTOISE B 338 101 280)
98, Rue de la Belle Etoile, Z.I. Paris Nord Il,
B.P. 50016, 95945 Roissy Charles de Gaulle
Cedex, France
Phone 01-48638989
YAMAGATA Corporation
2-6-34,Takashima, Nishi-ku, Yokohama, Kanagawa, Japan
Designed by ALPINE Japan
Printed in Japan (Y)
68-04123Z81-B
Autogood products internet store http://130.com.ua
01GB01TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
SE
CT
01GB00TMEM860.book Page 2 Wednesday, February 22, 2006 11:30 AM
a
.u
m
o
c
.
0
13
Autogood products internet store http://130.com.ua
01GB02TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
PS-Card-Euro.fm Page 3 Tuesday, February 7, 2006 3:00 PM
a
.u
m
o
c
.
0
13
Autogood products internet store http://130.com.ua
PS-Card-Euro.fm
PS Card Euro - 3
PS-Card-Euro.fm Page 4 Tuesday, February 7, 2006 3:00 PM
a
.u
m
o
c
.
0
13
Autogood products internet store http://130.com.ua
PS-Card-Euro.fm
PS Card Euro - 4
PS-Card-Euro.fm Page 5 Tuesday, February 7, 2006 3:00 PM
a
.u
m
o
c
.
0
13
Autogood products internet store http://130.com.ua
PS-Card-Euro.fm
PS Card Euro - 5
PS-Card-Euro.fm Page 6 Tuesday, February 7, 2006 3:00 PM
a
.u
m
o
c
.
0
13
Autogood products internet store http://130.com.ua
PS-Card-Euro.fm
PS Card Euro - 6
01GB00TMEM860.book Page 1 Wednesday, February 22, 2006 11:30 AM
ENGLISH
Contents
Adjusting Image Contrast ..............................9
Adjusting Picture Quality ..............................9
Operating Instructions
Navigation System (Optional)
WARNING
Auxiliary Device (Optional)
Switching the Navigation Screen (Optional) ....9
Operating Auxiliary Devices (Optional) .........10
WARNING ................................................. 2
CAUTION .................................................. 2
PRECAUTIONS ........................................ 2
Getting Started
Location of Controls ........................................ 4
About the Touch Button Operation .................. 4
Turning Power On or Off ................................. 4
Adjusting the Volume ....................................... 4
Switching the Source ........................................ 5
Hardkey Operation ........................................ 5
Touch Button Operation ................................ 5
Operating S-VIDEO Devices (Optional) ........10
Operating Other Products via Touch
Screen
Operating Other Products via Touch Screen ...11
Operating a DVD in the IVA-D310 series/IVAD300 series/DVA-9965 series/DVA-9860
series .........................................................11
Operating the DVA-5210/DVE-5207 and the
DHA-S680 series .....................................12
If a TV is operated
(A TV tuner is connected) ........................12
Operating the VPE-S431 .............................13
Operating the TUE-T200DVB ....................13
a
.u
m
o
c
.
Setup
GENERAL Setup
S-VIDEO Device (Optional)
0
13
General Setup Operation .................................. 5
DISPLAY Mode ............................................ 6
Setting the Brightness of the Backlighting ... 6
Rear Monitor Select Function ....................... 6
Change Sound Output ................................... 6
Sound (Beep) Guide Function ...................... 6
Setting the Install Position ............................ 6
Turning the Touch Panel Vibration
ON or OFF ................................................. 7
Adjusting the External Input Audio Level .... 7
External Input Name Setting ......................... 7
Setting of the Rear Camera ........................... 7
Setting the Navigation Mode ........................ 7
Adjusting the Level of Backlight .................. 7
Setting the GUIDE CONTROL .................... 7
Adjusting the Touch Panel ............................ 7
Information
In Case of Difficulty .......................................14
Specifications ..................................................14
Installation and Connections
Warning .................................................. 15
Caution ................................................... 15
Precautions ........................................... 15
Installation ......................................................16
Installing the Main unit B.Box ....................16
Attaching the monitor and stand ..................17
Connections (TME-M860 Wiring Diagram) ...19
System Example .............................................21
VISUAL EQ™
Visual EQ Setting Operation ............................ 8
Selecting the VISUAL EQ Mode
(Maker’s setting) ........................................ 8
Storing VISUAL EQ ..................................... 8
Adjusting Brightness ..................................... 8
Adjusting Colour of Picture .......................... 9
Adjusting Tint of Picture .............................. 9
Autogood products internet store http://130.com.ua
1-EN
01GB03TMEM860TOC.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 2 Wednesday, February 22, 2006 11:30 AM
Operating Instructions
DO NOT BLOCK VENTS OR RADIATOR PANELS.
WARNING
Doing so may cause heat to build up inside and may result in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire,
electric shock or other injury.
WARNING
This symbol means important instructions.
Failure to heed them can result in serious injury
or death.
INSTALL THE PRODUCT CORRECTLY SO THAT THE DRIVER
CANNOT WATCH TV/VIDEO UNLESS THE VEHICLE IS
STOPPED AND THE EMERGENCY BRAKE IS APPLIED.
DO NOT INSTALL THE MONITOR NEAR THE PASSENGER
SEAT AIR BAG.
If the unit is not installed correctly the air bag may not function
correctly and when triggered the air bag may cause the monitor to
spring upwards causing an accident and injuries.
CAUTION
It is dangerous for the driver to watch TV/Video while driving a
vehicle. Installing this product incorrectly enables the driver to
watch TV/Video while driving. This may cause a distraction,
preventing the driver from looking ahead, thus causing an accident.
The driver or other people could be severely injured.
DO NOT WATCH VIDEO WHILE DRIVING.
This symbol means important instructions.
Failure to heed them can result in injury or
material property damage.
a
.u
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
m
o
c
.
Watching the video may distract the driver from looking ahead of
the vehicle and cause an accident.
Failure to do so may cause personal injury or damage to the
product. Return it to your authorized Alpine dealer or the nearest
Alpine Service Centre for repairing.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR
ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE.
0
13
Any function that requires your prolonged attention should only be
performed after coming to a complete stop. Always stop the vehicle
in a safe location before performing these functions. Failure to do
so may result in an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL
HEAR OUTSIDE NOISE WHILE DRIVING.
Failure to do so may result in an accident.
PRECAUTIONS
Product Cleaning
Use a soft dry cloth for periodic cleaning of the product. For more
severe stains, please dampen the cloth with water only. Anything
else has the chance of dissolving the paint or damaging the plastic.
Temperature
Be sure the temperature inside the vehicle is between +45°C
(+113°F) and 0°C (+32°F) before turning your unit on.
MINIMIZE DISPLAY VIEWING WHILE DRIVING.
Viewing the display may distract the driver from looking ahead of
the vehicle and cause an accident.
DO NOT DISASSEMBLE OR ALTER.
Maintenance
If you have problems, do not attempt to repair the unit yourself.
Return it to your Alpine dealer or the nearest Alpine Service
Station for servicing.
Doing so may result in an accident, fire or electric shock.
Installation Location
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE
REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed,
consult a physician immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING
FUSES.
Failure to do so may result in fire or electric shock.
2-EN
Make sure the TME-M860 will not be installed in a location
subjected to:
•
•
•
•
Direct sun and heat
High humidity and water
Excessive dust
Excessive vibrations
• After turning the system off, a slight ghost of the image will
remain temporarily. This is an effect peculiar to LCD technology
and is normal.
• In cold temperature conditions, the screen may lose contrast
temporarily. After a short warm-up period, it will return to
normal.
Autogood products internet store http://130.com.ua
01GB04TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 3 Wednesday, February 22, 2006 11:30 AM
Operation of some of the functions of this unit is very complex.
Because of this, it was deemed necessary to place these functions
into a special screen. This will restrict operation of these functions
to times when the vehicle is parked. This ensures the focus of the
driver’s attention will be on the road and not on the TME-M860.
This has been done for the safety of the driver and passengers.
The setup operation cannot be made if the car is moving. The car
must be parked and the parking brake must be engaged for the
procedure described in the Owner’s Manual to be valid. The
warning “CAN’T OPERATE WHILE DRIVING,” will be
displayed if any attempts are made to perform these operations
while driving.
a
.u
m
o
c
.
0
13
Autogood products internet store http://130.com.ua
3-EN
01GB04TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 4 Wednesday, February 22, 2006 11:30 AM
Turning Power On or Off
Getting Started
1
2
Press POWER to turn on the unit.
Press POWER to turn off the unit.
• Some operation of the unit cannot be performed while the vehicle is
in motion. In this case, be sure to first stop your vehicle and apply the
parking brake, then perform the operation.
• In low ambient temperature conditions, the display may be dark for a
short period of time immediately after the power is turned on. Once
the LCD has warmed up, the display returns to normal.
• For your safety, some operation of the unit cannot be performed
while the vehicle is in motion. In this case, first stop the vehicle and
engage the parking brake, then perform the operation.
• If the voltage of the vehicle's battery power is low, the screen may
blink. This is normal and not a malfunction.
Location of Controls
Adjusting the Volume
SOURCE button
Each time you press the SOURCE button, SOURCE is
switched.
Adjust the volume level by pressing
a
.u
POWER button
Turns the power on and off.
m
o
c
.
Senses the brightness of the car interior
Remote Sensor
Point the optional remote control transmitter toward the
remote sensor within a range of 2 m.
Volume button
0
13
Adjust the volume level by pressing the
Monitor
.
Volume: 0 - 30
POWER Indicator
DIMMER Sensor
or
or
button.
About the expression of buttons in this Owner’s
Manual
• The buttons on this unit are expressed in bold (e.g. POWER). The
touch buttons on the display are expressed in bold with [ ] (e.g.
[SOURCE]).
• This Owner’s Manual explains mainly the function of touch
buttons, when a touch button and a hardkey have the same
function.
About the Touch Button Operation
The display unit is equipped with tactile feedback (PULSE TOUCH).
What is the tactile feedback (PULSE TOUCH) ?
When you touch a button graphic in the display, you will feel a
mild vibration and click on the display panel surface. This
feedback enables you to easily identify action areas in the
display.
• Be sure to touch the button lightly with the pad of your finger on the
display to protect the display.
• If you touch a button and there is no reaction, remove your finger
from the display once, and try again.
4-EN
Autogood products internet store http://130.com.ua
01GB05TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 5 Wednesday, February 22, 2006 11:30 AM
Switching the Source
Setup
Hardkey Operation
GENERAL Setup
Each time you press SOURCE, SOURCE is switched as
follows.
NAV.
AUX-1
AUX-2
S-VIDEO
General Setup Operation
NAV.
NAV.:
Displays the navigation screen. (When connected to the Alpine’s
Navigation system)
AUX-1 / AUX-2 / S-VIDEO:
Displays the screen of the DVD player etc. that is connected to
the AUX-1/AUX-2/S-VIDEO INPUT jack.
Touch Button Operation
1
2
Touch any point on the display to display the
operation screen for each source.
The following steps 1 to 4 are common operations to each
“Setting item” of GENERAL Setup. Refer to each section for
details.
1
Touch [SOURCE].
2
Touch the desired source.
a
.u
Touch [GENERAL SETUP].
The GENERAL SETUP screen appears.
The main source screen is displayed.
3
Display example for source selection screen
Change the setting by touching [ ] or [ ] of the
desired setting item.
m
o
c
.
0
13
Displays source modes that can be selected
(The kind of source modes that are displayed
varies depending on connection and setting)
Press and hold SOURCE for at least 2 seconds.
The SETUP selection screen is displayed.
The source selection screen is displayed.
3
The Parking Brake must be engaged to access the setup mode
screen. Attempting to access this screen while driving will display
the warning-CAN’T OPERATE WHILE DRIVING.
Setting items:
DISPLAY MODE / DIMMER / AUX OUT / SOUND OUT / BEEP
PULSE TOUCH / AUX IN1·2 LEVEL / AUX IN 1·2MODE /
S-VIDEO MODE / CAMERA IN / NAV. MODE / DIMMER LEVEL
HIGH / DIMMER LEVEL LOW /GUIDE CONTROL / SCREEN
ALIGNMENT / INSTALL POSITION
Touch [
4
] or [
] to scroll screen-by-screen.
Touch [RETURN] to return to the normal screen.
• Immediately after changing the settings of General Mode (While the
system is writing data automatically) do not turn the ignition key
(engine key) to OFF.
Otherwise, the settings may not be changed.
Autogood products internet store http://130.com.ua
5-EN
01GB05TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 6 Wednesday, February 22, 2006 11:30 AM
DISPLAY Mode
Each time you touch [
] or [
Rear Monitor Select Function
Setting item : AUX OUT
Setting contents : LINK / NAV. / AUX-1 / AUX-2 / S-VIDEO
], the mode is switched.
Setting item: DISPLAY MODE
Setting contents: WIDE / CINEMA / NORMAL
Output the video/audio portion shown on the main
monitor, to the rear monitor.
NAV.:
Output the navigation video/audio to the rear
monitor.
AUX-1:
Output the AUX1 video/audio to the rear monitor.
AUX-2:
Output the AUX2 video/audio to the rear monitor.
S-VIDEO: Output the S-VIDEO video to the rear monitor.
LINK:
In WIDE mode, the monitor displays a normal picture wider to fit
in a wide-screen monitor by evenly stretching out the picture
horizontally.
• NAV. is displayed when NAV. is set in “Setting the Navigation Mode”
(page 7).
• AUX-1/AUX-2/S-VIDEO are not displayed when they are set to OFF
in “External Input Name Setting” (page 7).
Change Sound Output
Setting item: SOUND OUT
Setting contents: OFF / MONITOR / HEADPHONES
OFF:
Sound is not output.
MONITOR:
Outputs sound through the built-in speakers.
HEADPHONES: Outputs sound to headphones if connected.
In CINEMA mode, the monitor displays a normal picture by
stretching out the picture vertically. This mode is good for
displaying a cinema type picture at the 16 : 9 ratio.
a
.u
• The audio interruption setting for the navigation system takes
precedence over the sound output from other audio sources (radio,
CD player, etc.) regardless of setting items.
m
o
c
.
* Note that sound will not be output unless the audio output settings
are appropriate.
0
13
In NORMAL mode, the monitor displays a normal picture at the
centre of the screen with a vertical black band at each side.
• In the Navigation mode, you can only set to WIDE.
Setting the Brightness of the Backlighting
Backlighting is provided by a fluorescent light built into the liquid
crystal panel. The illumination control adjusts the brightness of the
backlighting based on the car ambient lighting for easier viewing.
Setting item: DIMMER
Setting contents: HIGH / LOW / AUTO
Sets the brightness of the screen to the same
brightness that was set in DIMMER LEVEL HIGH in
“Adjusting the Level of Backlight” (page 7).
LOW: Sets the brightness of the screen to the same
brightness that was set in DIMMER LEVEL LOW in
“Adjusting the Level of Backlight” (page 7).
AUTO: Adjust the brightness of the background illumination of
the monitor automatically to the brightness of the car
interior.
HIGH:
• When the source name of AUX 2 and S-VIDEO terminals is set to the
DVD HU, the adjustment of the audio level is made with the head
unit. In this case, sound is not output through the built-in speakers or
headphones. To output sound through the built-in speakers or
headphones, set to REAR in “Setting the Install Position” (page 6).
• The audio output level of navigation interruption is equal to the
volume level of the navigation mode.
Sound (Beep) Guide Function
Setting item: BEEP
Setting contents: OFF / ON
ON: Activate the Sound Guide mode.
OFF: Deactivate the Sound Guide mode. The sound guide
beep will not be produced when a button on the unit is
pressed.
Setting the Install Position
When you install this unit in the rear seat and use the optional
headphones/built-in speakers, set to REAR in this setting. If you set to
FRONT, the volume level adjustment cannot be made when you use the
optional headphones/built-in speakers.
Setting item: INSTALL POSITION
Setting contents: FRONT/REAR
FRONT: When installing this unit in the front seat
REAR: When installing this unit in the rear seat
6-EN
Autogood products internet store http://130.com.ua
01GB05TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 7 Wednesday, February 22, 2006 11:30 AM
Turning the Touch Panel Vibration ON or
OFF
You can turn the touch panel’s vibration ON or OFF during operation.
Setting item: PULSE TOUCH
Setting contents: OFF / ON
OFF:
ON:
Adjusting the Level of Backlight
You can adjust the brightness of the backlight (HIGH and LOW). This
function could be used, for instance, to change the screen brightness
while travelling at night.
Setting a maximum brightness
Turns off vibration during operation.
Turns on vibration during operation.
Setting item: DIMMER LEVEL HIGH
Setting contents: 16~31
Adjusting the External Input Audio Level
Setting item: AUX IN 1 LEVEL / AUX IN 2 LEVEL
Setting contents: HIGH / LOW
You can adjust the level between MIN (16) and MAX (31).
When it reaches the minimum or maximum point, the display
shows “MIN” or “MAX” respectively.
Setting a minimum brightness
HIGH: Increases the external input audio level
LOW: Decreases the external input audio level
Setting item: DIMMER LEVEL LOW
Setting contents: 0~15
• This setting cannot be made when AUX IN 1 MODE/AUX IN 2
MODE is set to OFF in “External Input Name Setting”.
You can adjust the level between MIN (0) and MAX (15).
When it reaches the minimum or maximum point, the display
shows “MIN” or “MAX” respectively.
External Input Name Setting
Select the name from the following list, to be used for the product using
the external input mode. This will apply to the touch switch name at
source selection time and the source name during playback change.
Setting item: AUX IN 1 MODE / AUX IN 2 MODE / S-VIDEO MODE
Setting contents:
0
13
• When you set to OFF, you cannot do operations concerning AUX or
S-VIDEO from this unit.
When the rear camera is connected, rear pictures are output on the
screen.
Setting item: CAMERA IN
Setting contents: OFF / ON
a
.u
It is audio interruption setting for the navigation system.
Setting item: GUIDE CONTROL
Setting contents: STANDARD / EUROPE
m
o
c
.
AUX IN 1: OFF / TV / DVB-T / EXT. DVD / GAME / AUX 1
AUX IN 2: OFF / TV / DVB-T / EXT. DVD / GAME / AUX 2 /
LINK / DVD HU
S-VIDEO: OFF / S-VIDEO / DVD HU
Setting of the Rear Camera
Setting the GUIDE CONTROL
OFF: The CAMERA source is not displayed on the SOURCE
selection screen.
ON: Even if the shift lever is not set to reverse (R), the rear
pictures are output by selecting the CAMERA source.
• By shifting to reverse (R), the rear pictures are output.
This function is effective when the reverse wire is properly connected.
Setting the Navigation Mode
When you connect an optional navigation equipment, set it to NAV.
Setting item: NAV. MODE
Setting contents: OFF / NAV. / EXT.
For European customers:
Be sure to set to “EUROPE”.
For customers in other countries: Be sure to set to “STANDARD”.
The setting can be made only when NAV. or EXT. is set in
“Setting the Navigation Mode”.
Adjusting the Touch Panel
Adjustment becomes necessary when the display position on the LCD
and the touch position on the touch panel do not match.
Setting item: SCREEN ALIGNMENT
Setting contents:
(RESET) /
(SETUP)
1 Touch [
] of SCREEN ALIGNMENT.
The adjustment screen appears.
2 Accurately touch the
mark provided in the lower left
corner of the screen.
The screen changes to the adjustment screen.
3 Accurately touch the
mark provided in the upper right
corner of the screen.
This completes adjustment, and returns to the GENERAL
setup mode screen.
• If you have touched a location other than the
mark, touch the
mark to restore the adjustment screen to the initial setting.
• If you touch [RETURN] on the adjustment screen, no adjustment is
done and the GENERAL setup screen is restored.
OFF: Navigation source is not displayed. The settings related
to the navigation can not be changed from this unit.
NAV.: Navigation source is displayed.
EXT.: The source name is displayed as EXT..
Autogood products internet store http://130.com.ua
7-EN
01GB05TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 8 Wednesday, February 22, 2006 11:30 AM
Selecting the VISUAL EQ Mode (Maker’s
setting)
VISUAL EQ™
You can select a mode suitable for the subject image.
Visual EQ Setting Operation
Setting item: VISUAL EQ MODE
Setting contents: OFF / NIGHT M / SOFT / SHARP / CONTRAST /
P-1 / P-2
Initial Setting
Suitable for movies in which dark scenes
frequently appear.
SOFT:
Suitable for CGs and animated films.
SHARP:
Suitable for old movies where images are not
clearly shown.
CONTRAST: Suitable for recent movies.
P-1:
Recalls the VISUAL EQ mode being stored on
preset No.P-1 from “Storing VISUAL EQ” (page 8).
P-2:
Recalls the VISUAL EQ mode being saved on
preset No.P-2 from “Storing VISUAL EQ” (page 8).
OFF:
NIGHT M:
The following steps 1 to 5 are common operations to each
“Setting item” of VISUAL EQ setting. Refer to each section for
details
1
Press and hold SOURCE for at least 2 seconds.
The SETUP selection screen is displayed.
2
Touch [Visual EQ].
VISUAL EQ screen appears.
• To return to the initial setting, after selecting any one of the setting
contents (NIGHT M to CONTRAST) and adjusting a desired
brightness, picture tint, etc., set this function to OFF.
• If your desired brightness, picture tint, etc., are adjusted after
selecting any one of the setting contents, “CUSTOM” is displayed.
3
Setting items:
BRIGHT
COLOR*
VISUAL EQ MODE*
TINT*
CONTRAST
USER MEMORY*
] or [
].
5
0
13
Change the setting on the selected item by touching
its [ ] or [ ].
Touch [RETURN] to return to the normal screen.
• Visual EQ setting cannot be made in the CAMERA mode.
You can store the settings made for “Adjusting Image Brightness, Tint,
Depth, Picture Quality and Contrast.”
m
o
c
.
SHARP*
* The setting is available in the visual source mode. (except RGB
navigation screen)
4
a
.u
Storing VISUAL EQ
Select a desired setting item by touching [
Setting item: USER MEMORY
Setting contents: P-1 / P-2
1 After completing “Adjusting Image Brightness, Tint,
Depth, Picture Quality, and Contrast” (pages 8, 9), touch
[ ] or [ ] of USER MEMORY and then select preset
number “P-1” or “P-2” to which the settings are to be
stored.
2 After selecting a preset No., touch [WRITE].
The adjusted VISUAL EQ mode is stored by the above
operations.
• You can recall the VISUAL EQ mode stored here from P-1 or P-2 of
“Selecting the VISUAL EQ Mode (Maker’s setting)” (page 8).
Adjusting Brightness
Setting item: BRIGHT
Setting contents: -15 ~ +15
You can adjust the brightness between MIN (–15) and MAX
(+15). When it reaches the minimum or maximum point, the
display shows “MIN” or “MAX” respectively.
• The brightness is automatically adjusted according to the car's
interior brightness if AUTO is set in “Setting the Brightness of the
Backlighting” (page 6).
8-EN
Autogood products internet store http://130.com.ua
01GB06TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 9 Wednesday, February 22, 2006 11:30 AM
Adjusting Colour of Picture
Setting item: COLOR
Setting contents: -15 ~ +15
You can adjust the colour between MIN (–15) and MAX (+15).
When it reaches the minimum or maximum point, the display
shows “MIN” or “MAX” respectively.
• Tint adjustment cannot be made in NAV mode (with the RGB feature
connected).
Adjusting Tint of Picture
Navigation System
(Optional)
Switching the Navigation Screen
(Optional)
If an optional Alpine Navigation System is connected to the TMEM860, the Navigation screen can be displayed on this unit.
Setting item: TINT
Setting contents: G15 ~ R15
Adjust the colour from G15 to R15. “G MAX” or “R MAX” is
displayed at the maximum of each colour.
• Tint adjustment cannot be made in NAV mode (with the RGB feature
connected).
• When PAL signal is input, you cannot adjust the TINT.
Adjusting Image Contrast
1
Touch [SOURCE] on the main source screen.
The source selection screen appears on the display.
2
Touch [NAV.].
The Navigation screen is displayed.
The operation is possible with the supplied navigation
remote control.
For navigation operation, refer to the Owner’s Manual of the
navigator.
a
.u
Setting item: CONTRAST
Setting contents: -15 to +15
Adjustment of contrast is done in the range of LOW (-15) to
HIGH (+15). “HIGH” and “LOW” appear as the maximum and
minimum values specified.
m
o
c
.
• Image contrast is automatically adjusted according to the car's
interior brightness if AUTO is set in “Setting the Brightness of the
Backlighting” (page 6).
0
13
Adjusting Picture Quality
Setting item: SHARP
Setting contents: -15 to +15
• If the NAV. is not displayed on the source selection screen, set NAV.
MODE to NAV. by following “Setting the Navigation Mode”
(page 7).
• When the Navigation System is on, the audio navigation cuts in.
Adjustment of picture quality is done in the range of -15 to +15.
“HARD” and “SOFT” appear as the maximum and minimum
values specified.
• Tint adjustment cannot be made in NAV mode (with the RGB feature
connected).
Autogood products internet store http://130.com.ua
9-EN
01GB06TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 10 Wednesday, February 22, 2006 11:30 AM
Auxiliary Device
(Optional)
S-VIDEO Device
(Optional)
Operating Auxiliary Devices (Optional)
Operating S-VIDEO Devices (Optional)
To operate your devices connected to the AUX terminals of TMEM860, follow the procedure described below.
To operate your devices connected to the S-VIDEO terminals of TMEM860, follow the procedure described below.
WARNING
It is dangerous for the driver to watch the TV/Video
while driving the vehicle. The driver may be distracted
from looking ahead and an accident could occur.
WARNING
It is dangerous for the driver to watch the TV/Video
while driving the vehicle. The driver may be distracted
from looking ahead and an accident could occur.
Install the TME-M860 correctly so that the driver
cannot watch TV/Video unless the vehicle is stopped
and the hand brake is applied.
Install the TME-M860 correctly so that the driver
cannot watch TV/Video unless the vehicle is stopped
and the hand brake is applied.
If the TME-M860 is not installed correctly, the driver
will be able to watch the TV/Video while driving the
vehicle and may be distracted from looking ahead and
cause an accident. The driver or other people could
be severely injured.
If the TME-M860 is not installed correctly, the driver
will be able to watch the TV/Video while driving the
vehicle and may be distracted from looking ahead and
cause an accident. The driver or other people could
be severely injured.
a
.u
m
o
c
.
• If you try to activate the auxiliary device while driving, the display
will show the warning-PICTURE OFF FOR YOUR SAFETY.
• If you try to activate the auxiliary device while driving, the display
will show the warning-PICTURE OFF FOR YOUR SAFETY.
1
1
Touch [SOURCE] on the main source screen.
The source selection screen appears on the display.
2
0
13
Touch [AUX-1]* or [AUX-2]*.
The external input screen is displayed.
Touch [SOURCE] on the main source screen.
The source selection screen appears on the display.
2
Touch [S-VIDEO]*.
The S-VIDEO input screen is displayed.
* The name which is given as the source name in “External Input
Name Setting” on page 7 is displayed.
* The name which is given as the source name in “External Input
Name Setting” on page 7 is displayed.
• If the AUX mode is not displayed on the source selection screen, set
AUX IN to other than OFF by following “External Input Name
Setting” on page 7.
• If the S-VIDEO mode is not displayed on the source selection screen,
set S-VIDEO to other than OFF by following “External Input Name
Setting” on page 7.
• If the source name is set to anything other than AUX-1/AUX-2/GAME
in “External Input Name Setting” on page 7, an operation screen
(function keys) is displayed. When the source name is set to LINK,
the “AUDIO” or “EXT.DVD” operation screen is displayed, which
can be toggled by touching [CONTROL] on their screens. For
operation screen details, see “Operating Other Products via Touch
Screen” on page 11. The “AUDIO” operation screen is the same as
the “DVD HU” operation screen except that the former has no
SOURCE button, otherwise their button operations are the same.
• For operation screen (function keys) details, see “Operating Other
Products via Touch Screen” on page 11. When the source name is set
to S-VIDEO in “External Input Name Setting” on page 7, the
“AUDIO” or “EXT.DVD” operation screen is displayed, which can
be toggled by touching [CONTROL] on their screens. The “AUDIO”
operation screen is the same as the “DVD HU” operation screen
except that the former has no SOURCE button, otherwise their button
operations are the same.
10-EN
Autogood products internet store http://130.com.ua
01GB06TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 11 Wednesday, February 22, 2006 11:30 AM
Operating Other Products via Touch
Screen
Operating Other Products via Touch Screen
When the TME-M860 is used in combination with a product designed to be operated from the TME-M860 (IVA-D310 series/IVA-D300 series/DVA9965 series/DVA-9860 series/DVA-5210/DVE-5207/DHA-S680 series etc.), some of the operations on the other product can be performed from the
TME- M860. Below are some examples of the operations that can be performed.
• The TME-M860 and other components connected to it can be operated with a separately sold remote control unit. For instructions on operations
using the remote control unit, see the remote control unit’s operating instructions.
• Depending on the connected component, some functions and operations may differ. Also refer to the operating instructions of the connected
component.
Operating a DVD in the IVA-D310 series/IVA-D300 series/DVA-9965 series/DVA-9860 series
Connect these models to the AUX IN 2 or S-VIDEO terminal, and set to “DVD HU” in “External Input Name Setting” (page 7).
Touch any point on the display.
a
.u
The “DVD HU” operation screen appears.
m
o
c
.
0
13
Operation of DVD in IVA-D310 series/IVA-D300 series/DVA-9965 series/DVA-9860 series
Touch
Long touch
Play from start of current chapter
2x fast reverse/8x fast reverse after 5 seconds
Play/pause
Play next chapter
–
PRE STOP/STOP
2x fast forward/8x fast forward after 5 seconds
Slow play (from pause mode)
STOP
–
–
–
–
SOURCE
–
Switch page (function guide)
–
Move menu cursor
–
Enter (DVD menu)
–
Move back to the previous menu screen
–
Call out DVD menu
–
Switch page (function guide)
–
• When operating an IVA-D310 series/IVA-D300 series, see the “Rear Entertainment Function” section of the IVA-D310 series/IVA-D300 series
operating instructions.
Autogood products internet store http://130.com.ua
11-EN
01GB06TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 12 Wednesday, February 22, 2006 11:30 AM
Operating the DVA-5210/DVE-5207 and the DHA-S680 series
Set to “EXT.DVD” in “External Input Name Setting” (page 7).
Touch any point on the display.
The “EXT.DVD” operation screen appears.
Operation of a DVD player (DVA-5210/DVE-5207)
Operation of a DVD changer (DHA-S680)
Touch
Long touch
Touch
Long touch
Play from start of current chapter 2x fast reverse/ 8x fast reverse Play from start of current chapter
16x fast reverse
after 5 seconds
Play/pause
Play
Slow play
Play next chapter
a
.u
Play next chapter
16x fast forward
PRE STOP/STOP
2x fast forward/8x fast forward
after 5 seconds
Slow play (from pause mode)
STOP
PRE STOP/STOP
-
-
-
Switch DISC
-
-
-
Switch DISC
-
Switch page (function guide)
-
Move menu cursor
-
Enter (DVD menu)
Move back 1 screen
(DVD player setup)*
Call out DVD menu
Switch page (function guide)
*Stop mode only
m
o
c
.
-
0
13
-
Call out DVD player setup
screen*
-
Switch page (function guide)
-
Move menu cursor
-
Enter (DVD menu)
-
Move back 1 screen
(DVD changer setup)*
Call out DVD menu
-
Switch page (function guide)
Call out DVD changer setup
screen*
-
*Stop mode only
If a TV is operated (A TV tuner is connected)
Set to “TV” in “External Input Name Setting” (page 7).
Touch any point on the display.
The “TV” operation screen appears.
TV Operation
Touch
Channel down
12-EN
Long touch
-
Channel up
-
Auto memory
-
Preset channel down
-
Preset channel up
-
Change band
-
Autogood products internet store http://130.com.ua
01GB06TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 13 Wednesday, February 22, 2006 11:30 AM
Operating the VPE-S431
Connect to the AUX IN 2 terminal, set to “LINK” in “External Input Name Setting” (page 7).
Touch any point on the display.
The “LINK” operation screen appears.
• By touching [CONTROL] on the upper right side of the screen, the display switches between the “AUDIO” operation screen and “EXT.DVD”
operation screen.
• For details, refer to the Owner's Manual of the expansion box (VPE-S431) sold separately.
Operating the TUE-T200DVB
Set to “DVB-T” in “External Input Name Setting” (page 7).
Touch any point on the display.
a
.u
The “DVB-T” operation screen appears.
m
o
c
.
0
13
DVB-T Operation
Touch
Channel down
Channel up
Scan
Long touch
Continuous channel down
Continuous channel up
–
Favorite channel down
–
Favorite channel up
–
Source select
–
EPG display
–
Switch page (function guide)
–
Move menu cursor
–
Enter
–
Return
–
• For details, refer to the Owner's Manual of the TUE-T200DVB sold separately.
Autogood products internet store http://130.com.ua
13-EN
01GB06TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 14 Wednesday, February 22, 2006 11:30 AM
• Monitor’s parking brake is not set.
- Connect the monitor’s parking brake lead and set the parking
brake.
(For details, refer to the monitor’s instructions.)
Information
In Case of Difficulty
If you encounter a problem, please turn the power off, then on again.
If the unit is still not functioning normally, please review the items
in the following checklist. This guide will help you isolate the
problem if the unit is at fault. Otherwise, make sure the rest of your
system is properly connected, or then consult your authorized
Alpine dealer.
Picture is unclear or noisy.
• Vehicle’s battery power is weak.
- Check the battery power and wiring.
(The unit may malfunction if the battery power is under 11
volts with a load applied.)
• Monitor’s fluorescent tube is worn.
- Replace the monitor’s fluorescent tube.
Spots or dotted lines/stripes appear.
• Caused by neon signs, high-voltage power lines, CB transmitter,
other vehicle's ignition plugs, etc.
- Change the location of your vehicle.
Basic
No function or display.
• Vehicle’s ignition is off.
- If connected according to the instructions, the unit will not
operate with the vehicle’s ignition off.
• Improper power lead connections.
- Check power lead connections.
• Blown fuse.
- Check the fuse on the battery lead of the unit; replace with the
proper value if necessary.
No sound or unnatural sound.
• Connections are not properly or securely made.
- Check the connections and firmly connect.
MONITOR SECTION
Screen Size
8.0-type
LCD Type
Transparent type TN LCD
Operation System
TFT active matrix
Number of Picture Elements 1,152,000 pcs.
Effective Number of Picture Elements
99.99% or more
Illumination System
Cold cathode fluorescent tube
a
.u
m
o
c
.
Screen not displayed.
• Brightness control is set at the minimum position.
- Adjust the Brightness control.
• Temperature in the vehicle is too low.
- Increase the vehicle’s interior temperature to operation
temperature range.
• Connections to the DVD, navigation system are not securely
made.
- Check the connections and firmly connect.
Unclear or noisy display.
• Fluorescent plate is worn out.
- Replace the fluorescent plate.
Specifications
0
13
Navigation system inoperative.
• Connections to the navigation system are incorrect.
- Check the connections with the navigation system and connect
the cables correctly and firmly.
GENERAL
Power Requirement
14.4 V DC
(11–16 V allowable)
(Monitor Section) 680 g
(1 lbs. 8 oz)
(B.box Section) 880 g
(1 lbs. 15 oz)
Weight
CHASSIS SIZE (Monitor section)
Width
Height
Depth
205 mm (8-1/16")
35 mm (1-3/8")
145 mm (5-45/64")
CHASSIS SIZE (B.box)
Unclear picture display.
• Fluorescent tube is exhausted.
- Replace the fluorescent tube*.
Width
Height
Depth
* The fluorescent tube replacement is not free of charge even within the
warranty period, for the tube is an article of consumption.
• Due to continuous product improvement, specifications and design
are subject to change without notice.
• The LCD panel is manufactured using an extremely high precision
manufacturing technology. Its effective pixel ratio is over 99.99%.
This means that there is a possibility that 0.01% of the pixels could
be either always ON or OFF.
Unit does not operate.
• Monitor’s power is not turned on.
- Turn on the monitor’s power.
222 mm (8-21/32")
30 mm (1-3/16")
164 mm (6-29/64")
No picture is produced.
• Monitor’s mode is not switched to the mode you want to see.
- Switch to the mode you want to see.
• Monitor’s parking brake lead is not connected.
- Connect the monitor’s parking brake lead and set the parking
brake.
(For details, refer to the monitor’s instructions.)
14-EN
Autogood products internet store http://130.com.ua
01GB06TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 15 Wednesday, February 22, 2006 11:30 AM
Installation and Connections
Before installing or connecting the unit, please read the
following and pages 2 to 3 of this manual thoroughly for
proper use.
Caution
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.
The wiring and installation of this unit requires special technical
skill and experience. To ensure safety, always contact the dealer
where you purchased this product to have the work done.
Warning
MAKE THE CORRECT CONNECTIONS
Failure to make the proper connections may result in fire or product
damage.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM
SECURELY.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
Be sure to use only the specified accessory parts. Use of other than
designated parts may damage this unit internally or may not
securely install the unit in place. This may cause parts to become
loose resulting in hazards or product failure.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE
NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to
electrical shorts.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN
SURROUNDING OBJECTS.
Arrange wiring and cables in compliance with the manual to
prevent obstructions when driving. Cables or wiring that obstruct or
hang up on places such as the steering wheel, shift lever, brake
pedals, etc. can be extremely hazardous.
Route the cables and wiring away from moving parts (like the seat
rails) or sharp or pointed edges. This will prevent crimping and
damage to the wiring. If wiring passes through a hole in metal, use
a rubber grommet to prevent the wire’s insulation from being cut by
the metal edge of the hole.
a
.u
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR
DUST.
m
o
c
.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock.
0
13
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING
HOLES.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
When drilling holes in the chassis for installation, take precautions
so as not to contact, damage or obstruct pipes, fuel lines, tanks or
electrical wiring. Failure to take such precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING
SYSTEMS TO MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other
safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could disable
control of the vehicle and cause fire etc.
KEEP SMALL OBJECTS SUCH AS BOLTS OR SCREWS OUT
OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed,
consult a physician immediately.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER
VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR
SHIFT LEVER.
Avoid installing the unit in locations with high incidence of
moisture or dust. Moisture or dust that penetrates into this unit may
result in product failure.
Precautions
• Be sure to disconnect the cable from the (–) battery post before
installing your TME-M860. This will reduce any chance of
damage to the unit in case of a short-circuit.
• Be sure to connect the color coded leads according to the
diagram. Incorrect connections may cause the unit to
malfunction or damage to the vehicle’s electrical system.
• When making connections to the vehicle’s electrical system, be
aware of the factory installed components (e.g. on-board
computer). Do not tap into these leads to provide power for this
unit. When connecting the TME-M860 to the fuse box, make
sure the fuse for the intended circuit of the TME-M860 has the
appropriate amperage. Failure to do so may result in damage to
the unit and/or the vehicle. When in doubt, consult your
ALPINE dealer.
• The TME-M860 uses female RCA-type jacks for connection to
other units having RCA connectors. You may need an adaptor to
connect other units. If so, please contact your authorized
ALPINE dealer for assistance.
• The Display must be completely retracted in the casing when
installing. If it is not, problems may occur.
Doing so may obstruct forward vision or hamper movement etc.
and results in serious accident.
IMPORTANT
Please record the serial number of your unit in the space provided
below and keep it as a permanent record. The serial number plate is
located on the bottom of the unit.
SERIAL NUMBER:
INSTALLATION DATE:
INSTALLATION TECHNICIAN:
PLACE OF PURCHASE:
Autogood products internet store http://130.com.ua
15-EN
01GB07TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 16 Wednesday, February 22, 2006 11:30 AM
When mounting with Screws
Installation
When mounting the blackbox with the screws, be sure to choose a flat
location.
When making holes, be careful not to scratch any pipes or wires.
Accessory List
Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Main unit B.Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Display cable (6m) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Parking brake lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Velcro fastener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Tapping Screw (M4×14) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Cord clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Monitor stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Fixing Screw (M4×12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Cloth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Owner's Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1
Install the unit on the floor with the supplied flangehead tapping screws (M4 × 14).
Flange-head tapping screws
(M4 × 14) (Included)
Main unit
B.Box
Installing the Main unit B.Box
When mounting with Velcro fasteners
When mounting the blackbox with the Velcro fasteners, be sure to
choose a flat location.
Do not hang the unit from the bottom of the dashboard or rear deck with
the Velcro fasteners.
1
Place Velcro fastener.
Put on two pieces of Velcro fastener on the
mounting positions.
a
.u
m
o
c
.
Attach two pieces of Velcro fastener with the rough side
facing toward the unit.
2
WARNING
When you are drilling a hole in the car body, be
careful not to damage pipes, tanks or electrical wiring
etc.. It might cause an accident or a fire.
0
13
Put on two pieces of the Velcro fastener (soft one) on the
mounting positions and mount the unit.
Velcro Fasteners
16-EN
Autogood products internet store http://130.com.ua
01GB07TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 17 Wednesday, February 22, 2006 11:30 AM
3
Attaching the monitor and stand
CAUTION
Do not install the monitor near the front passenger
seat air bag system.
1
Check the sticking position.
ATemporarily fasten the stand with gum tape.
BLoosen the adjustment screws, and adjust to a safe,
viewable position.
The fixed arm tilts towards the seat side.
Remove the main unit attachment fitting.
Angle
adjustment
screw
Pull this part to release.
Seat side
Front glass side
Main unit
attachment fitting
2
Loosen the main unit attachment fitting with a coin
etc., slide it into the track on the rear of the main unit
and temporarily fasten it. Then fix it to the stand.
a
.u
Main unit
Line of sight
0
13
m
o
c
.
Slide in an
upward direction.
Dashboard
If the main unit
invades your line
of sight then it will
block your view.
In order to use safely, attach to the following places.
• Stable and secure places.
• Places that will not have your view blocked by the main
unit when driving.
• Places that you will not hit against if you lean forward
while you wearing your seatbelt.
• Places where the main unit cannot hit against the steering
wheel while driving.
• Be aware that if the surface of the dashboard is leather, wooden
panel, stretched fabric or any non-resin based product, then the
surface will be damaged when you remove the stand.
• Do not place the main unit directly in front of the air conditioner
vents.
Autogood products internet store http://130.com.ua
17-EN
01GB07TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 18 Wednesday, February 22, 2006 11:30 AM
4
5
Remove the main unit from the stand.
Parking Brake Lead Connection
Remove the mount from the stand and stick it to the
dashboard etc.. Remove any dirt on the place to
install, using the supplied cloth.
If necessary, use a pinch connector to connect the parking brake lead,
etc.
1
Fixing screws
(M4 x 12 Supplied)
Vehicle Cable
Pinch Connector
Monitor Cable
Stopper
2
If the place of
attachment is
curved, then
bend this
part to match
the shape.
• Locate the unit and route the leads at least 10 cm away
from the car harness.
• Keep the battery power leads as far away from other
leads as possible.
• Connect the ground lead securely to a bare metal spot
(remove any paint, dirt or grease if necessary) of the car
chassis.
• If you add an optional noise suppressor, connect it as far
away from the unit as possible. Your Alpine dealer carries
various noise suppressors, contact them for further
information.
• Your Alpine dealer knows best about noise prevention
measures so consult your dealer for further information.
m
o
c
.
0
13
Attach the main unit to the stand as shown in step 2.
Use the cable clamps to fix the cables.
• Before using, check that the main unit and the stand, and the stand
and the place where it is attached to the car are fixed securely.
18-EN
a
.u
To prevent external noise from entering the audio system.
Mount
• If the temperature in the car is low (Winter), then first heat up the
place where you are going to stick the mount with a hairdryer etc.
• Do not apply force to the mount, or expose to humidity, within 24
hours after attaching.
• If the mount is not firmly stuck, then we recommend that you attach
with the supplied fixing screws.
6
Pliers
Autogood products internet store http://130.com.ua
01GB07TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 19 Wednesday, February 22, 2006 11:30 AM
Connections (TME-M860 Wiring Diagram)
REMOTE OUT (AUX 1)
(White/Brown)
REMOTE OUT (AUX 2)
TME-M860 Main unit B.Box
(White/Brown)
REMOTE OUT (AUX 3)
a
.u
(White/Brown)
M. CONT
(White/Pink)
m
o
c
.
PARKING BRAKE
(Yellow/Blue)
ACC
0
13
(Red)
REVERSE
(Orange/White)
GND
(Black)
Autogood products internet store http://130.com.ua
19-EN
01GB07TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 20 Wednesday, February 22, 2006 11:30 AM
Remote Control Output Lead (AUX 1) (White/Brown)
Display Output Terminal
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
Remote Control Output Lead (AUX 2) (White/Brown)
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
Remote Control Output Lead (AUX 3) (White/Brown)
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
Monitor Control Lead (White/Pink)
Connect this to the Monitor Control Lead of the touch panelcompatible product.
Parking Brake Lead (Yellow/Blue)
Connect this lead to the power supply side of the parking
brake switch to transmit the parking brake status signals to
the TME-M860.
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+)
12V only when the ignition is turned on or in the accessory
position.
Reverse Lead (Orange/White)
Use only when a back-up camera is connected. Connect to
the plus side of the car’s reverse lamp that lights when the
transmission is shifted into reverse (R).
Switches the video picture to the back-up camera. This is
linked with putting the car into reverse (R).
a
.u
m
o
c
.
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
Audio input Terminals (AUX 1)
0
13
Use these terminals to input the audio signals from a DVD
player, video deck etc.
Video input Terminal (AUX 1)
Use this terminal to input the video signals from a DVD
player, video deck etc.
Video input terminal for a rear view back-up camera
Use this terminal to input the video signals from a rear view
camera.
Audio input Terminals (AUX 2)
Use these terminals to input the audio signals from a DVD
player, video deck etc.
Video input Terminal (AUX 2)
Use this terminal to input the video signals from a DVD
player, video deck etc.
S Video input Terminal (AUX 3/ S-VIDEO)
Use this terminal to input the S-video signals.
RGB Input Terminal
Connect this to the RGB output terminal of the Navigation
System.
Headphone
Video output Terminal
Use this terminal to output video signals to a rear monitor,
etc.
Audio output Terminals
Use these terminals to output audio signals to a rear
monitor, etc.
Main monitor
Fuse Holder (7.5A)
Power Supply Connector
20-EN
Autogood products internet store http://130.com.ua
01GB07TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 21 Wednesday, February 22, 2006 11:30 AM
System Example
Connect the Navigation system and DVD player
TME-M860 Main unit B.Box
To audio output terminal
DVD player
(such as DVE-5207,
sold separately)
To video output terminal
ALPINE’S
Navigation
(sold separately)
(White/Brown)
Power Supply Connector
RGB Input Terminal
m
o
c
.
REMOTE OUT (AUX 1)
0
13
RGB Cable (Included with Navigation)
a
.u
Connect this to the RGB output terminal of the Navigation
System.
AUX Video/Audio Input Terminal
REMOTE IN
(White/Brown)
RCA Extension Cable (Included with DVD video
player)
RCA Extension Cable (Sold separately)
Remote Control Output Lead (White/Brown)
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
Connect the video/audio output lead of a DVD video player
or DVD changer to this terminal.
Autogood products internet store http://130.com.ua
21-EN
01GB07TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 22 Wednesday, February 22, 2006 11:30 AM
When Connecting External Equipment
To Audio Input terminal
Rear monitor
(Sold Separately)
TME-M860 Main unit B.BOX
To Video Input terminal
To Audio Output terminal
TV Tuner or VCR
(Sold Separately)
To Video Output terminal
Back-up camera
(Sold Separately)
(White/Brown)
REMOTE OUT
(Orange/White)
REVERSE
REMOTE IN
(White/Brown)
a
.u
m
o
c
.
Use only when back-up camera is connected.
RCA Extension Cable (Sold separately)
Power Supply Connector
CAMERA Input Terminal
0
13
Use when connecting a back-up camera.
AUX Video/Audio Output Terminal
Use when connecting an optional monitor etc.
AUX Video/Audio Input Terminal
22-EN
Remote Control Output Lead (White/Brown)
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
Reverse Lead (Orange/White)
Connect to the plus side of the car’s reverse lamp which
lights when the transmission is shifted into reverse (R).
Switches the video picture to the back-up camera. This is
linked to putting the car into reverse (R).
Autogood products internet store http://130.com.ua
01GB07TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)
01GB00TMEM860.book Page 23 Wednesday, February 22, 2006 11:30 AM
Connect the DVD player
TME-M860 Main unit B. BOX
DVD player
(such as DVA-9860 series,
sold separately)
To video output connector
(White/Pink)
(White/Brown)
M.CONT
M.CONT
REMOTE OUT(AUX 2)
(White/Pink)
REMOTE IN
(White/Brown)
a
.u
RCA Extension Cable (video)
Monitor Control Lead (White/Pink)
Power Supply Connector
Connect this to the Monitor Control Lead of the touch panelcompatible product.
m
o
c
.
Remote Control Output Lead (White/Brown)
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
0
13
Connect the DVD player (to the S video terminal)
TME-M860 Main unit B. BOX
DVD player
(such as DVA-9965 series,
sold separately)
To S video output terminal
(White/Pink)
M.CONT
(White/Brown)
REMOTE OUT(AUX 3)
M.CONT
(White/Pink)
REMOTE IN (FRONT)
(White/Brown)
S-video cable (Included with DVD video player)
Monitor Control Lead (White/Pink)
Power Supply Connector
Connect this to the Monitor Control Lead of the touch panelcompatible product.
Remote Control Output Lead (White/Brown)
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
Autogood products internet store http://130.com.ua
23-EN
01GB07TMEM860.fm
ALPINE TME-M860 68-04123Z81-B (EN)