- Computers & electronics
- Computer cables
- Cable splitters or combiners
- Channel Plus
- 5115BID
- User manual
advertisement
WARRANTY
Multiplex Technology, Inc. warrants this product to be free from defects in materials and workmanship for a period of one year from the date of purchase or MTI will repair, or at its option, replace the defective product. To obtain warranty service, call MTI for a return material authorization (RMA) number and return the product prepaid to Multiplex Technology, Inc., 3001 Enterprise
Street, Brea, CA 92821, Attention: Customer Service.
Please put the RMA number on the outside of the carton.
Any implied warranty arising from the sale of the product including implied warranties of merchantability and fitness for purpose are limited to the warranty stated above. MTI shall not be responsible for losses or damages or expenses, whether direct, consequential or incidental arising from the use of or the inability to use this product. Some states do not allow limitations on how long the implied warranty lasts or the exclusions or limitations or incidental or consequential damages, so the above limitations and exclusions may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which may vary from state to state.
P E R F O R M A N C E M U LT I - R O O M V I D E O
5115 Modulator Series
Model 5115HHR
Model 5115BID
Model 5115PAL
600-132 Rev.A
©1999 Multiplex Technology, Inc., Brea, Ca.
714-996-4100 * 800-999-5225 * fax 714-996-4900 * www.channelplus.com
The 5115 series is a audio/video distribution system that creates a new channel to add to existing television channels. The new channel carries audio/video from any video source to all the TVs in the home
The 5115 was designed to install effortlessly into existing coax home wiring or into new construction.
Contents: Channel Injector
Wall plate
Power Injector
Power Supply
Coax Jumper
The 5115 series is comprised of a wall plate and a channel injector.
The channel injector is weather resistant and designed to mount indoors or outdoors close to the incoming CATV or antenna feed.
The system uses the existing coax cable distribution in the house and only requires a single run of Cat 5.
The 5115 was designed to work with Cat 5 wiring. Although the system will function with quad wire, Cat 5 delivers the highest quality picture. The Cat 5 allows the use of an automatic line length sensor and picture compensator. Quad wire does not take advantage of this enhancement.
Model Differences:
The model 5115HHR is a high headroom design for CATV and off air antenna feeds only.
The model 5115BID is a bi-directional design for use with CATV cable boxes that are interactive or require bi-directional communications with the cable company.
The model 5115PAL is designed to modulate PAL frequencies and use CATV or off air antenna feeds.
Installation:
First, locate the incoming CATV or antenna feed and install the channel injector at that location.
Second, install the wall plate at the desired location and run Cat 5 wire from the wall plate to the channel location. Then connect a video source.
Third, apply power and select an unused channel for the 5115 picture to appear on all the televisions.
2
Installation
Step One
Locate the incoming CATV or antenna feed and existing splitter.
(Usually found on the side of the house, in the attic or near the electrical and phone service box)
Remove the lock screw located on the bottom of the channel injector and slide the cover off. Use the mounting holes as shown to affix the channel injector to the wall next to the splitter.
Mount the injector within
4” of the splitter Use mounting holes on the bottom plate to attach channel injector to the wall
Disconnect the incoming CATV or antenna feed from the existing splitter and attach it to the channel injector as shown.
Before
Incoming CATV or antenna coax
Out to TVs
Now attach the supplied coax jumper back to the existing splitter and tighten all connections with a 7/16” wrench.
After
Mount the injector within
4” of the splitter
Supplied coax jumper goes back to splitter
Incoming CATV or antenna coax
Out to TVs
3
Installation of the wall plate
Step Two
The wall plate mounts using a low voltage ring into a wall cut out.
Run a line of Cat 5 wire from the wall plate to the channel injector and connect wires as shown.
Side view of wall plate note:
When using Cat 5 wire remove the default resistor that is in pins 3 and 4 of the wall plate screw terminal pin
1
2
3
Bl/W
Blue
4
5
6
7
8
Org/W
Orange
Gr/W
Green
Br/W
Brown
Default resistor note:
When using quad wire connect wires only to pins 1, 2, 5 and 6.
Leave the resistor in place at pins 3 and 4.
pin
1
2
Green
Red
5 Black
6 Yellow
Connecting A Video Source
Using any video source, DVD,Satellite or VCR connect it to the wall plate as shown. This video source will be transmitted over the Cat 5 wire to the channel injector.
Audio/video connections
Video source
* Optional loop out television or a/v receiver
Cat 5 wire
Coax jumper
Norm/Loop switch
Out to
TVs
Antenna or
CATV feed
* Use the NORM / LOOP switch to select the proper setting for your application.
At the channel injector, connect Cat 5 wire as shown. Follow the color coding on the screw terminal.
When using only quad wire use positions 1, 2, 5 and 6 and follow color coding.
NORM:
Select NORM when a television or a/v receiver is not used at the wall plate to view the connected source.
LOOP:
Select LOOP when a television or a/v receiver is connected to the wall plate to view the connected source
4 blue/white pin 1 run the Cat 5 wire through the grommet at the bottom of the injector blue/white pin 1
5
Applying Power and Programming
Step Three
The 5115 series has three different methods for applying power to the system.
Use only one method for applying power.
Method One: Apply power directly to the channel injector with the power supply.
Method Two: Use the power injector to apply power along the Cat
5 or quad wire run. Cut the connecting wire along the run and insert the power injector. Connect the wires using the color coding. Then plug the power supply into the power injector.
power injector power supply pin 1 blue/white power supply cut Cat 5 wire power plug
Lower right of channel injector
Power plug
The green LED in the upper right corner of the channel injector will be lit showing power is active.
Method Three: Apply power directly at the wall plate.
The green LED in the upper right corner of the injector will be lit showing power is active.
(See power length requirements page 8)
The green LED in the lower right corner of the wall plate and upper right corner of the channel injector will be lit showing power is active.
power plug
6 7
Power Length Requirements
Method One
Up to 300’ of
Cat 5 or quad wire maximum
Power Length Requirements
Method Two
Up to 100’ of
Cat 5 or quad wire maximum
Up to 300’ of
Cat 5 or quad wire maximum power plug power plug
Power Length Requirements
Method Three
Up to 100’ of
Cat 5 or quad wire maximum power plug
8
How to Program
Determine which unused channel you want to view your video source on and program the injector for that channel. There must be one unused channel both before and after the selected channel to avoid interference. The new channel will be combined with the existing channels and appear on all televisions.
Upper right corner on channel injector green LED programming button
To program: For example channel 60
1: Press the button 6 times.
2: Wait for the LED to relight.
3: Press the button 10 more times (pressing 10 times enters “0”).
The injector will now combine the wall plate feed on channel 60 with all other existing channels from the incoming CATV or antenna.
To program a three digit channel: For example channel 120
1: Press the button 1 time.
2: Wait for the LED to relight.
3: Press the button 2 more times.
4: Wait for the LED to relight.
5: Press the button 10 more times.
Finding Unused Channels
CATV: Determine the highest channel number delivering a picture, excluding 95-99. Tune the TV up one channel at a time from the last channel with a picture until finding one channel with no trace of a picture or interference, just snow.
Antenna: Tune the TV one channel at a time from channel 14-64.
Locate one channel that has no trace of a picture or interference, just snow.
9
Programming a New Channel
Valid channels are 14 thru 64 for UHF and 65 thru 125 for CATV
Channels 95-99 are not available. Channels 21 thru 62 are for Pal.
Channel Spacing:
Skip at least one number between the new channel and the closest existing UHF/CATV channel.
(example 14 and 16: OK 14 and 15: Unacceptable)
Error Indication:
If an error occurs or an incorrect channel is entered, the LED will flash quickly for one second and return to previous settings.
Cable HRC and IRC considerations:
Most cable services use IRC frequency assignments. This is the default for the 5115. However, if the cable services uses HRC or the TV appears to search for the “created channel”, program the channel injector for HRC.
For HRC enter 98. Reset to IRC by entering 99.
Entries 98 and 99 are for setting HRC or IRC only. They will not change the channel number.
With programming complete, test each TV in the system to see that it is receiving the new channel.
Specifications: typical @ 25°C ± 5° C
5115HHR / 5115BID 5115PAL(AUS) video input format NTSC CCIR input signal 1.0 V peak-to-peak @ 75
Ω output 12dBmV normal - 15.5dBmV maximum input connectors 3 RCA (video + audio left + audio right) loop-thru connectors 3 RCA (video + audio left + audio right) video termination 75
Ω or > 1 M
Ω in “loop” position (selectable) tuning range UHF 14 to 64 21 to 62(28 to 67)
CATV 65 to 125 A power supply included with product mains power 105 to 125 210 to 250 output of power supply 15VDC 600mA general width x height x depth injector module wall plate
6.5” x 3.5” x 1.25” 1.25” x 4.0” x 1.75”
(16.3cm x 9cm x 3.2cm) (3.2 cm x 10.5cm x 4.0cm) shipping weight operating temperature
2 lbs (0.9 kg)
–4°F to 131°F (–20°C to 55°C)
A excluding channels 95 through 99
10 11
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project