Craftsman 137.218250 Owner's Manual

Owner's Manual

CRRFTSMRNo

2.7 HP (Maximum Developed)

10" Inch Blade

5000 R.P.M.

TABLE SAW

Model No.

137,218250

E82443

USED 37J2

CAUTION:

Before using this Table Saw,

read this manual and follow

all its Safety Rules and

Operating Instructions.

• Safety Instructions

• Installation

• Operation

• Maintenance

• Parts List

• EspaSol

Customer Help Line

1-800-843-1682

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

Part No. 137218250001

SECTION

Warranty

.................

Product Specifications

......

Safety Instructions

.........

Accessories and Attachments

,e,,,oo,e==

=,.,,,,o=.,

,o=.,oe.,,o

°=,,°.o,e,.

Tools needed for assembly ..

Carton Contents

...........

Know Your Table Saw

.....................

q.°=,..=,..

.°e..e,...,

Assembly and Adjustments

...............

Operation

Maintenance

...........................

........................

Troubleshooting guide ..

..............

Parts

.............................

_ i

Making a push stick

.................

Espanol

...........................

°.°,lw,

=°,,e,°

,,o°,ow e,°,lw,

.o,l.,,

,e,w,°w

.o.e..

.o.,i.,

•

.we=.le.

,..eo.

weg,,w,°J,w,°,.,q°,,

,Iwoe,°,l°,,*g,=*w,=

*..e...*,w.eJw,e..e.

e.,e.wee..e,=.e.w.e°

,,,,,°,=,e,,,e

,°e°,e,,*=.,e.

=,°,l,w,.°,e°,

..=,.oee..*..e

.*o°.._..=,.=e

*.o.e.w.,o.e,.

,..,.o.e..,.,°

.*l=..*,..,..e

e.=q°.°o...

el=.ei.°e=, we

,e

°, w=

°,,°,e°2

e°l.°=,2

,e°,.°e3 e,,*,,°

• e

°.

e=.w°.,

.w..e..6

e°e=.*.°6

• e

..

.......

........

e°

..........

..........

.........

...........

=.°..e9

PAGE

6

6

16

20

21

22

33

37

FULL ONE YEAR WARRANTY

If this product fails due to a defect in material or workmanship within one year from the date of purchase, Sears

will repair it free of charge.

Contact a Sears Service Center for repair.

If this product is used for commercial or rental purposes, this warranty applies only for 90 days from the date of

purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179

MOTOR

HP (Maximum developed)

Type .......................

Amps ......................

Voltage .....................

Hz ........................

RPM (no load) ...............

Overload Protection ...........

......

2.7

Universal

15

120

60

5000

YES

SAW

Table ......................

Table extension ..............

Extension fence capacity

Blade ......................

.......

26-7/64" x 19-3/32"

Yes, with fence

24"

10"

Rip scale ...................

Rip fence ..................

YES

YES

Miter gauge .................

YES

Leg set .....................

YES

Maximum Depth of cut at 90 ° ....

3"

Maximum Depth of cut at 45 ° ....

2-1/2"

Maximum Dado cut width .......

1/2"

Net weight ..................

61.6 Lbs.

To avoid electrical hazards, fire hazards, or damage to the tool, use proper circuit protection.

Your table saw is wired at the factory for 120V operation.

Connect to a 120V, 15 AMP branch circuit and use a 15

AMP time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.

2

GENERAL SAFETY INSTRUCTIONS

Safety is a combination of common sense, staying alert and knowing how to use your table saw.

To avoid mistakes that could cause serious injury, do not plug the table saw in until you have read and understood the following:

.

KEEP GUARDS IN PLACE and in working order.

3.

REMOVE ADJUSTING KEYS AND WRENCHES.

Form the habit of checking to see that keys and

adjusting wrenches are removed from the tool before

turning ON.

4.

KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

5.

BEFORE USING THE TABLE SAW

.

.

READ and become familiar with this entire instruction manual. LEARN the tool's applications, limitations, and possible hazards.

DON'T USE IN A DANGEROUS ENVIRONMENT.

Don't use power tools in damp or wet locations, or

expose them to rain. Keep work area well lighted.

KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from the work area.

7,

8.

9.

MAKE WORKSHOP KID PROOF with padlocks, master

switches, or by removing starter keys.

DON'T FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed.

USE THE RIGHT TOOL. Don't force tool or the attachment to do a job for which it was not designed.

10. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized

cord will cause a drop in line voltage resulting in loss

of power and overheating.The table on page 5 shows

the correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next

heavier gauge. The smaller the gauge number, the heavier the cord.

11. WEAR PROPER APPAREL, DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other

jewelry which may get caught in moving parts.

Nonslip footwear is recommended. Wear protective

hair covering to contain long hair.

12.

ALWAYS WEAR EYE

PROTECTION. Any table saw can throw foreign

objects into the eyes which

could cause permanent

eye

damage. ALWAYS wear

Safety Goggles (not glasses) that comply with ANSI safety standard Z87.1.

Everyday eyeglasses have only impact-resistant lenses. They ARE NOT safety glasses. Safety

Goggles are available at Sears. NOTE: Glasses or goggles not in compliance with ANSI Z87.1 could

seriouslyhurt you when they break.

13.

WEAR A FACE MASK OR DUST MASK.

Sawing operation produces dust.

14.

SECURE WORK. Use clamps or a vise to hold work

when practical. It's safer than using your hand and it frees both hands to operate tool.

15. DISCONNECT TOOLS before servicing, and when

changing accessories, such as blades, bits, cutters, and the like.

16.

REDUCE THE RISK OF UNINTENTIONAL STARTING.

Make sure the switch is in OFF position before plugging in.

17.

USE RECOMMENDED ACCESSORIES.

Consult the

owner's manual for the recommended accessories.

The use of improper accessories may cause risk of

injury to persons.

18.

NEVER STAND ON TOOL. Serious injury could occur

ifthe tool is tipped or if the cuttingtool is unintentionally

contacted.

19.

CHECK FOR DAMAGED PARTS. Before further use of

the tool, a guard or other part that is damaged should

be carefully checked to determine that it will operate

properly and perform its intended function. Check for

alignment of moving parts, binding of moving parts,

breakage of parts, mounting, and any other conditions

that may affect its operation. A guard or other part that

is damaged should be properly repaired or replaced.

20.

NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN THE POWER OFF. Don't leave the tool until

it comes to a complete stop:

21.

DON'T OVERREACH.

Keep proper footing and balance at all times.

22. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance.

Follow

instructions for lubricating and changing accessories.

23. DIRECTION OF FEED. Feed work into a blade or cutter

against the direction of rotationof the blade or cutter only.

SAVE THESE INSTRUCTIONS

3

24. WARNING: Dust generated from certain materials can be injurious to your health. Always operate saw in well ventilated areas and provide for proper dust removal.

SPECIFIC SAFETY INSTRUCTIONS

FOR THE TABLE SAW

1.

ALWAYS USE SAW BLADE GUARD spreader and anti-kickback pawls for every operation for which

they can be used, including through-sawing.

Through-sawing operations are those in which the blade cuts completely through the workpiece when ripping or cross-cutting.

2.

4.

ALWAYS HOLDTHE WORK FIRMLY against the miter gauge or rip fence.

3.

USE A PUSH STICK when required. Always use a push stick for ripping narrow stock. Refer to ripping

applications in the instruction manual where the

push stick is covered in detail. See the push stick

pattern included in this Owner's Manual.

NEVER PERFORM ANY OPERATION

"FREE HAND", which means using your hands

only to support or guide the workpiece. Always

use either the fence or the miter gauge to position

and guide the work.

5.

NEVER STAND or have any part of your body in line with the path of the saw blade, Keep your

hands out of the line of the saw blade.

14. AVOID AWKWARD OPERATIONS and hand positions where a sudden slip could cause your

hand to move into the cuffing tool.

15.

NEVER USE SOLVENTS to clean plastic parts.

Solvents could possibly dissolve or otherwise

damage the material. Only a soft damp cloth should

be used to clean plastic parts.

16.

MOUNT your table saw before performing any cuffing operations.

Refer to installation instructions.

17.

NEVER CUT METALS or materials which may make

hazardous dust.

18. ALWAYS USE IN A WELL VENTILATED AREA.

Remove sawdust frequently. Clean out sawdust from

the interior of the saw to prevent a potential fire hazard.

19. NEVER LEAVE THE TOOL running unattended.

Don't leave the tool until it comes to a complete stop.

20. For proper operation follow the instructions of this owner's manual titled "SAW MOUNTED TO WORK

SURFACES" Failure to provide sawdust fall-through and removal hole will allow sawdust to build up in the motor area, which may result in a fire hazard or cause motor damage.

21. ALWAYS USE THE TABLE EXTENSION for support when cutting a long workpiece. Never use an

unstable surface or another person to hold a long workpiece. Adjust the table extension for maximum stability and length of the workpiece before cutting.

6.

NEVER REACH behind or over the cutting tool for any reason.

7.

REMOVE the rip fence when cross-cutting.

8.

DO NOT USE molding head set with this saw.

22. ALWAYS LOCKTHETABLE EXTENSION securely in place before cutting workpiece.

9.

FEEDWORK INTOTHE BLADE against the

direction of rotation only.

ELECTRICAL REQUIREMENTS

10. NEVER use the fence as a cut-off gauge when cross-cutting.

POWER SUPPLY AND MOTOR

SPECIFICATIONS

11. NEVER ATTEMPT TO FREE A STALLED SAW

BLADE without first turning the saw OFF. Turn

power switch OFF immediately to prevent motor damage.

12. PROVIDE ADEQUATE SUPPORT

to the rear and

sides of the saw table for wide or long workpieces.

13. AVOID KICKBACKS (work thrown back towards

you) by keeping the blade sharp, keeping the rip

fence parallel to the saw btade, and by keeping the spreader, anti-kickback pawls, and guard in place

and functioning.

Do not release work before it is

pushed all the way past the saw blade. Do not rip

work that is twisted, warped, or does not have a

straight edge to guide along the fence.

To avoid electrical hazards, fire hazards, or damage to the tool, use proper circuit protection. Use a separate electrical circuit for your tools.Your saw is wired at the factory for 120V operation. Connect to a 120V, 15 Amp circuit and use a 15 Amp time delay fuse or circuit breaker. To avoid shock or fire, if power cord is worn or cut, or damaged in any way, have it replaced immediately.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance for electric current and reduces the risk of electric shock, This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug, The plug

MUST be plugged into a matching receptacle that is properly installed and grounded in accordance with ALL

local codes and ordinances.

DO NOT MODIFYTHE PLUG PROVIDED.

If it will not fit the receptacle, have the proper receptacle installed by a qualified electrician.

IMPROPER CONNECTION of the equipment grounding

conductor can result in risk of electric shock. The conductor with the green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or replacement of the electric cord or plug is necessary, DO NOT connect the equipment grounding conductor to a live terminal.

CHECK with a qualified electrician or service person if you do not completety understand the grounding instructions, or if you are not sure the tool is properly grounded.

USE A SEPARATE ELECTRICAL

CIRCUIT for your tools. This circuit must not be less than #12 wire and

should be protected with a 15 Amp time delay fuse.

Before connecting the motor to the power line, make

sure the switch is in the OFF position and the electric

current is rated the same as the current stamped on the motor nameplate. Running at a lower voltage witl damage the motor.

This tool is intended for use on a circuit that has a receptacle like the one illustrated in FIGURE A. FIGURE A

shows a 3-preng electrical plug and receptacle that has a

grounding conductor. If a properly grounded receptacle is

not available, an adapter (FIGURE B) can be used to

temporarily connect this plug to a 2-contact ungrounded

receptacle. The temporary adapter should be used only

until a properly grounded receptacle can be installed by

a qualified technician. The adapter (FIGURE B) has a

rigid lug extending from it that MUST be connected to a

permanent earth ground, such as a properly grounded

receptacle box. The Canadian Electrical Code prohibits

the use of adapters.

CAUTION: In all cases, make certain the receptacle is properly grounded. If you are not sure have a qualified electrician check the receptacle.

Fig. A

Fig. B

Grounding Lug

3-Prong Plug f r

I I b J_ g Pronn

B

_

/

J _ Properly Grounded

3-Prong Receptacle

-- Make Sure This is Connected to a

Known Ground

"_ 2-Preng

Receptacle

GUIDELINES FOR EXTENSION CORDS

USE ONLY 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug. Repair or replace damaged or worn cord immediately.

USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to carry

the current your product will draw. An undersized cord will

result in a drop in line voltage and in loss of power which

will cause the tool to overheat. The table below shows the

correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier

gauge. The smaller the gauge number, the heavier the

cord.

Be sure your extension cord is properly wired and in

good condition.Always replace a damaged extension cord

or have it repaired by a qualified person before using it.

Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

This table saw is for indoor use only. Do not expose to rain or use in damp locations.

This tool must be grounded while in use to protect the operator from electrical shock.

i

Ampere more than

O

6

10

12

[IKI]

=111_._ !q_-VAtLJ.

Rating not more than

6

(when using 120 volts only)

Total length of cord in feet

25'

18

50*

16

100'

16

1 SO'

14

10

12

16

18

16

14

16

16

12

14

14

12

12

Not Recommended

SAVE THESE INSTRUCTIONS

RECOMMENDED ACCESSORIES

Visit your Sears Hardware Department or see the

Craftsman Power and Hand Tools Catalog to purchase recommended accessories for this power tool.

UNPACKING AND CHECKING CONTENTS

Separate all parts from packing material.

Check each one with the illustration and the list of loose parts to make certain all items are accounted for, before discarding any packing material.

To avoid the risk of personal injury:

•

Do not use adjustable (wobble) type dadoes or carbide tipped dado blades, maximum dado width is 1/2".

• Do not use a dado with a diameter larger than 6".

• Do not use molding head set with this saw.

• Do not modify this power tool or use accessories not recommended by Sears.

TOOLS NEEDED

Mediumscrewdriver

#2 Phillips screwdriver

I-Illllllll

Straight edge

Ill

Adjustable wrench

LI','_"'""''':',I

Combination square

'_

To avoid personal injury, if any parts are missing, do not attempt to assemble the table saw, plug in the power cord, or turn the switch on until the missing parts are obtained and are installed correctly.

TABLE

OF LOOSE

PARTS

L.

M.

N.

O.

R

Q.

D,

E.

F.

G.

H.

I.

J.

K.

ITEM DESCRIPTION

SAW

A.

B.

C.

Table saw

Blade guard and splitter

Bolt, flat washer, toothed washer, oval washer

Rip fence handle

Rip fence

Hand wheels

Dome nuts

Dado table insert

Miter gauge

Hex keys

Blade wrenches

STAND

Top bracket (short)

Top bracket (long)

Bottom bracket (short)

Bottom bracket (long)

Legs

Bag of bolts, nuts, foot pads

A_

1

1

leach

1

1

2

2

1

1

2

2

2

2

2

2

4

1

NOTE: To make assembly easier, keep contents of box together. Apply a coat of automobile wax to the table.

Wipe all parts thoroughly with a clean dry cloth. This will reduce friction when pushing the workpiece.

UNPACKING YOUR TABLE SAW:

A.

B.

C.

D.

E.

H.

o l

i

o

o _-_

I

0

13

L.

o o

M.

N, O,

R

J.

a.

K,

6

G.

Rip Fence

Blade Gl

Rip gauge storage

Miter gauge

Extension table

Blade bevel scale

Blade tilting handwheel

Leg stand

Blade

Kickback pawls Splitter

Blade bevel lock knob

Blade tilt pointer

Overload reset switch

ON/OFF switch with safety key

Blade elevation handwheel

Power¢

Blade wrenches

Table

Blade insert

Splitter

bracket

Extension fence

lock

handle

wrench

storage holes

ASSEMBLY INSTRUCTIONS

For your own safety, never connect plug to power source outlet until all assembly steps are complete, and you have read and understood the safety and operating instructions.

LEG SET (FIG. A)

1.

Separate all parts and group by size and style.

NOTE: Finger tighten bolts and nuts when joining parts.

2.

Use bolts (1), washers (2), and nuts (3) to assemble the leg set parts.

3.

Attach a leg (4) to the long top bracket (5). Attach the next leg to the opposite end of the top bracket.

4.

Repeat this assembly for the opposite side of the leg set.

5.

Attach the completed leg set assemblies to the short top brackets (6). Repeat on the opposite side.

6.

Insert bolt (7) Lntothe recessed hole of the foot pad (8).

7.

Insert into the leg flange hole and tighten, using washer (9) and nut (10). Repeat for the three other legs.

8.

Attach the bottom brackets (11) between each leg.

9.

Place the leg set on a level surface and tighten all nuts and bolts.

1

Fig. A 2

SAW TO LEG SET (FIG. B)

1.

Before mounting the blade guard, the rip fence and miter gauge to the saw top, invert the saw table so that it is facing the floor.

2.

Position the leg set upside down on the saw base.

3.

Match the holes of the stand to the holes on the bottom flange of the saw base.

4.

Secure the leg set to the saw base using bolts, washers, and nuts.

5.

When all bolts and nuts are tightened, carefully set the saw in its upright position.

6.

Position the saw on a clean, level surface.

Fig. B

Leg set mounting hole

Saw base hole

9

SAW MOUNTEDTO OTHER WORK SURFACES (FIG. C)

1.

If the leg set will not be used the saw must be properly

secured to a sturdy workbench using the four mounting

holes at the base of the saw.

2.

The surface of the table where the saw is to be

mounted must have a hole large enough to facilitate

sawdust fall-through and removal

3.

Square the saw on the mounting surface and mark

the location of the four 3/8" mounting holes (1).

4.

Drill 3/8" holes into the mounting surface.

5.

Mark a 12" to 14" square (2) centered between the four mounting holes (1).

6.

Cut out and remove the square.

7.

This opening will allow sawdust to fall through

the saw base.

8.

Place the saw on the work surface, and align the

mounting holes of the saw with those drilled through

the surface.

9.

Fasten the saw to the work surface.

Fig. C

Fig. D

BLADE RAISING HANDWHEEL (FIG. E, F)

1.

Attach the handwheel (1) to the elevation screw (2) at

the front of the saw.

Make sure the slots (3) in the hub of the handwheel

engage with the pins (4). (FIG. E)

2.

Attach and tighten the dome nut (5) at the end of the shaft (Fig. F).

Fig. E

(__

2

Q--.m

1

3

1

2 4

Failure to provide the sawdust fall-through hole will cause

sawdust to build up in the motor area, which may result

in fire or cause motor damage.

KEEPING THE AREA CLEAN (FIG. D)

1.

Sawdust and wood chips that fall from under the

saw will accumulate on the floor.

2.

Make it a practice to pick up and discard this dust when you have completed cutting.

BLADE TILTING HANDWHEEL (FIG. F)

1.

Attach the other handwheel (6) to the blade tilting screw on the side of the saw in the same manner

as above.

2.

Attach and tighten the handwheel dome nut (5).

Fig. F

--5

Always keep your work area clean, uncluttered and well lit. Do net work on floor surfaces that are slippery from sawdust or wax.

6

10

RIP FENCE (FIG. G)

1.

Thread the fence handle (1) into the cam hole (2)

until tight.

2.

Lift upward on the rip fence handle so that the

holding clamp (3) is fully extended.

3.

Place the rip fence on the saw table and engage

the holding clamp to the table rear. Lower the

front end onto the front rail (4).

4.

Push down on the fence handle to lock.

2.

Raise the blade arbor (4) (FIG. I) to the maximum height by turning the blade-raising handwheel counterclockwise.

3.

Remove the arbor nut (5) and flange (6), remove blade.

4.

Install the new saw blade onto the arbor with the blade teeth pointing toward the front of the saw.

5.

Install the flange (6) against the blade and thread the arbor nut (5) as far as possible by hand. Ensure that the blade is flush against the inner side of the blade flange.

To avoid possible injury and damage to the workpiece be sure to install the blade with the teeth pointing toward the front of the table in the direction of the rotation arrow on the blade guard.

Fig. I

4

CHANGING THE BLADE (FIG. H, I, J)

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outlet.

1.

Remove the table insert (1) by unscrewing the two screws (2, 3). Be careful not to lose the rubber washer that is on the back screw (3) beneath the table insert. (FIG. H)

NOTE: The back screw is longer than the front screw.

Fig. H

6.

To tighten the arbor nut (5) place the open end wrench jaws on the flats of the blade arbor to keep the arbor from turning. (FIG. J)

7.

Place the box-end wrench (8) on the arbor nut (5), and turn clockwise (to the rear of the saw table.)

8.

Replace the blade insert in the table recess, insert the screws through the front and rear holes and tighten.

Fig. J

•

8

3

2

11

To avoid injury from a thrown workpiece, blade parts, or blade contact, never operate saw without the proper insert in place. Use the saw blade insert when sawing. Use the dado head insert when using a dado.

BLADE GUARD ASSEMBLY (FIG. K, L, M)

1.

Set the blade to maximum height and the tilt to zero degrees on the bevel scale with the hand wheels.

Lock the blade lock knob.

2.

Place the external toothed lock washer (1) and a

steel flat washer (2) onto the long hex. head bolt (3).

Insert the bolt into the splitter bracket (4) as shown.

(FIG. K)

Fig. K

Fig. M

S

,/

anti-kickback pawl

8

,

-tfl I

I I I I /

I

I

3 i

ADJUSTMENT INSTRUCTIONS

3 2 1

3.

Place the oval washer (5) on the pivot rod (6). (FIG. L)

4.

Install the bracket assembly (4) into the rear of the saw table. Thread the bolt (3) into the internally threaded pivot rod.

NOTE: The splitter is removed from the illustration for clarity.

Fig. L

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source, before making any adjustments.

ADJUSTING THE TABLE EXTENSION (FIG.

O)

NOTE: The table extension may be installed on the right side of the table, as needed, to support long workpieces.

6 5

5.

Position the blade guard arm (7) to the rear of the table. (FIG. M)

6.

Using a straightedge, check that the blade guard splitter (8) is aligned with the saw blade (9).

7.

If straightening adjustment is necessary, loosen the bolt (3) and shift the splitter assembly to the right or left, or rotate.

8.

When the splitter is properly aligned with the saw blade, tighten the bolt.

NOTE: The splitter must always be correctly aligned so the cut workpiece will pass on either side without binding or twisting to the side.

12

To adjust the table extension position (FIG. O):

1.

Loosen the two clamp bolts (4) on the two

extension tube brackets.

2.

Slide the extension tubes in or out until the scale on

the front tube is positioned at the desired distance.

3.

Tighten the two lock handles.

To adjust the extension table fence:

1.

Loosen the locking handle (5) on the fence (6).

2.

Raise the fence to the desired height and tighten the

locking handle.

Fig, O

5 6

4

RIP FENCE ADJUSTMENT (FIG. Q)

,_lqllll[_

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outlet.

1.

The fence (1) is moved by lifting up on the handle (2) and sliding the fence to the desired location. Pushing down on the handle locks the fence in position.

2.

Position the fence on the right side of the table, and along one edge of the miter gauge grooves.

3.

Lock the fence handle. The fence should be parallel with the miter gauge groove.

4.

If adjustment is needed to make the fence parallel to the groove, do the following:

• Loosen the two screws (3) and lift up on the handle (2).

• Hold the fence bracket (4) firmly against the front of the saw table. Move the far end of the fence until it is parallel with the miter gauge groove.

• Tighten both screws and push the handle to lock.

5.

If fence is loose when the handle is in the locked

(downward) position, do the following:

• Move the handle (2) upward and turn the adjusting screw (5) clockwise until the rear clamp is snug.

Do not turn the adjusting screw more than 1/4 turn at a time.

• Over-tightening the adjusting screw will cause the fence to come out of alignment.

MITER GAUGE ADJUSTMENT (FIG. P)

1.

Make sure that the miter gauge will slide freely through

both table grooves.

2.

Loosen the lock knob (1). Set the pointer (2) to the 900 mark on the scale.

3.

Make a 900 cut in a piece of scrap wood. Check cut piece to see if it was cut at 90°. If it is not, continue to

adjust the miter gauge body (3) until the wood piece

is cut at 90 °. Refer to OPERATION section for cutting

instructions.

Fig. P

Fig. Q

_ il

© o

2

13

RIP FENCE INDICATOR ADJUSTMENT

(FIG, Q)

1.

The rip fence indicator (6) points to the measurement scale (8). The scale shows the distance from the side of the fence to the nearest side of the blade.

2.

Measure the actual distance with a rule. If there is a

difference between the measurement and the

indicator, adjust the indicator (6).

3.

Loosen the screw (7) and slide the indicator to the

correct measurement on the scale. Tighten screw

and remeasure with the rule.

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outlet.

ADJUSTING THE 90 ° AND 45 ° POSITIVE STOPS

(FIG. R, S)

Your saw has positive stops that will quickly position the saw blade at 90 ° or 45 ° to the table. These stops were set at the factory. Make adjustments only if necessary.

900 Stop

1.

Disconnect the saw from the power source.

2.

Turn the blade elevation handwheel and raise the blade to the maximum elevation.

3.

Loosen the blade bevel lock knob and move the blade to the maximum vertical position. Tighten the lock knob.

4.

Place a combination square on the table and against the blade (1') to determine if the blade is 90° to the table. (FIG. R)

5.

If the blade is not 90° to the table, loosen the two set screws (4), located in the bottom of the table saw,

(FIG. S) with the 3mm hex key, and back off the collar (5).

6.

Loosen the bevel lock knob. Turn the blade tilting handwheel to move the blade until it is 90 ° to the table.

7.

Adjust the collar (5) so it contacts the bracket (3) when the blade is 90° to the table. Tighten the two set screws (4).

Fig. R

90 ° 45 °

4.

Loosen the bevel lock knob; turn the tilting handwheel to move the blade until it is 45 ° to the table.

5.

Adjust the collar (5) so it contacts the bracket (3) when the blade is 45 °. Tighten set screws (4).

Fig. S

345

BLADE TILT POINTER

1.

When the blade is positioned at 90 °, adjust the

blade tilt pointer to read 0° on the scare.

2.

Loosen the holding screw, position the pointer over

0 ° and tighten the screw.

NOTE: Make a trial cut on scrap wood prior to making critical cuts. Measure for exactness.

BLADE PARALLEL TO MITER GAUGE

GROOVE (FIG. T, U)

This adjustment was made at the factory, but it should be rechecked and adjusted if necessary.

1 m

To prevent personal injury:

.Always disconnect plug from the power source when making any adjustments.

• This adjustment must be correct or kickback could result and accurate cuts cannot be made.

45° Stop

1.

With the blade in the upright 90 ° position, loosen the bevel lock knob. Turn the blade tilting handwheel and move the blade to the 45 ° position as far as it will go.

2.

Place the combination square on the table as shown in (FIG. R) to check if the blade is 45 o to the table.

3.

If the blade is not 45 ° to the table, loosen the two set screws (4) located under the table saw (FIG. S) with a 3 mm hex key, and back off the collar (5).

Initial adjustment (FIG.T)

1.

Remove the yellow switch key and unplug the saw.

2.

Move the blade guard out of the way.

3.

Raise the blade to the highest position and set at the 0° angle (90 ° straight up).

4.

Select and mark, with a felt tip marker, a blade tooth having a "right set".

5.

Place the combination square base (1) into the right side miter gauge groove (2). (FIG.T)

6.

Adjust the rule so it touches the front marked tooth and lock the ruler so it holds its position in the square assembly.

7.

Rotate the blade bringing the marked tooth to the rear and about 1/2 inch above the table.

14

9.

.

Carefully slide the combination square to the rear

until the ruler touches the marked tooth.

If the ruler touches the marked tooth at the front and

rear positions, no adjustment is needed at this time.

If not, perform adjustment procedure described in

next section.

Fig. T

Additional blade adjustments (FIG. U)

1.

If the front and rear measurements are not the

same, remove the combination square and loosen the four adjusting screws (1) on the top of the table about a half turn.

2.

With a folded piece of cardboard covering the blade

to protect your hands, move the blade careful{y to the left or right as much as needed to align the blade correctly.

3.

Tighten the four screws (1) and remeasure, as described in steps 4 to 9 in the prior section.

4.

If sufficient adjustment cannot be made by the four adjusting screws (1), then also loosen the two adjusting screws (2). Loosen these screws only if necessary.

5.

Recheck blade clearance making sure that the blade does not hit the table insert or other parts when at the 90 ° and 45 ° settings.

6.

Tighten all screws.

Fig. U

15

BASIC SAW OPERATIONS

RAISING THE BLADE (FIG. V)

To raise or lower the blade, turn the blade elevation

handwheel (1) to the desired blade height, and then

tighten lock handle (2) to maintain the desired blade

angle.

Fig. V

OVERLOAD PROTECTION (FIG. W)

This saw has a reset overload relay button (3) that will

restart the motor after it shuts off due to overloading or low voltage. If the motor stops during operation, turn the

ON/OFF

switch to the OFF position. Unplug the saw from

its power source. Wait about five minutes for the motor to cool down. Push in on the reset button (3) and turn the

switch to the ON position.

To avoid injury, the ON/OFF switch should be in the OFF position and the plug removed from the power source while the motor cool down takes place, to prevent accidental starting when the reset button is pushed. Overheating may be caused by misaligned parts or dull blade. Inspect your saw for proper setup before using it again.

USINGTHETABLE EXTENSION (FIG. X)

1

2

TILTING THE BLADE (FIG. V)

To tilt the saw blade for bevel cutting, loosen the

lock handle (2) and turn the tilting handwheel (3). Tighten the lock handle (2) to secure.

ON / OFF SWITCH (FIG. W)

The ON / OFF switch has a removable key. With the key

removed from the switch, unauthorized and hazardous use

by children and others is minimized.

1.

To turn the saw ON, insert key (1) into the slot in the switch (2). Move the switch upward to the ON position.

2.

To turn the saw OFF, move the switch downward.

3.

To lock the switch in the OFF position, grasp the sides

(or yellow part) of the switch toggle (1), and pull it out.

4.

With the switchkey removed, the switchwill not operate.

5.

If the switch key is removed while the saw is running,

it can be turned OFF but cannot be restarted without

inserting the switch key (1).

Fig. W

I

1.

Remove the stop screws from the ends of the tubes.

2.

Slide the ends of the tubes through both support

brackets on the side your workpiece will be needing

support, and replace the two stop screws.

3.

Rotate the front tube to display the scale as an

extension of the table top scale.

4.

Slide the extension out until the correct measurement

is displayed on the tube scale.

5.

Loosen the fence handles, and raise or lower the fence as needed.

6.

Tighten all extension support handles and knobs.

Fig. X

2

16

CU'B'ING OPERATIONS

There are two basic types of cuts: ripping and crosscutting.

Ripping is cutting along the length and the grain of the workpiece. Crosscutting is cutting either across the width or across the grain of the workpiece. Neither ripping nor crosscutting may be done safely freehand. Ripping requires the use of the rip fence, and crosscutting requires the miter gauge.

Fig.Y

Before you use the saw each and every time, check the following:

1.

Blade is tight on the arbor.

2.

Bevel angle lock knob is tight.

3.

If ripping, fence knob is tight and fence is parallel to the miter gauge grooves.

4.

Blade guard is in place and working properly.

5.

You are wearing safety glasses.

The failure to adhere to these common safety rules, and those printed in the front of this manual, can greatly increase the likelihood of injury.

RIPPING (FIG.Y,Z)

To prevent serious injury:

• Do not allow familiarity gained from the frequent use

of your table saw to cause careless mistakes.

Remember that even a careless fraction of a second is enough to cause a severe injury.

• Keep both hands away from the blade and path of the blade.

• The workpiece must have a straight edge against the fence and must not be warped, twisted, or bowed.

1.

Remove the miter gauge. Secure the rip fence to the table.

2.

Raise the blade so it is about 1/8" higher than the top of the workpiece.

3.

Place the workpiece flat on the table and against the fence. Keep the workpiece about 1" away from the blade.

4.

Turn the saw ON and wait for the blade to come up to speed.

5.

Slowly feed the workpiece into the blade by pushing forward only on the workpiece section (1) that will pass between the blade and the fence. (FIG.Y)

6.

Keep your thumbs off the table top. When both of your thumbs touch the front edge of the table (2), finish the cut with a push stick. Make a push stick using the pattern on page 33.

7.

The push stick (3) should always be used when the ripped workpiece is 2" or narrower (1). (FIG. Y)

8.

Continue pushing the workpiece with the push stick (3) until it passes the blade guard and clears the rear of the table.

9.

Never pull the workpiece back when the blade is turning. Turn the switch OFF. When the blade completely stops raise the anti-kickback pawls on each side of the splitter and slide the workpiece out.

Fig. Z

AVOID KICKBACK by pushing forward only on that section of the workpiece that will pass between the blade and the fence.

17

BEVEL RIPPING

This cut is the same as ripping except the blade bevel

angle is set to an angle other than 0 °.

Fig. AA

Cut only with the workpiece and the fence on the right side of the blade.

RIPPING SMALL PIECES

2

Avoid injury from blade contact. Never make through-saw

cuts narrower than 1/2" wide.

1.

2.

It is unsafe to rip small pieces. Instead, rip a larger piece to obtain the size of the desired piece.

When a small width is to be ripped and your hand cannot be safely put between the blade and the rip fence, use one or more push sticks to move the workpiece,

CROSSCUTTING (FIG. AA)

To prevent serious injury:

•

Do not allow familiarity gained from the frequent use of your table saw to cause careless mistakes.

Remember that even a careless fraction of a second is enough to cause a severe injury.

• Keep both hands away from the blade and path of the blade.

1

2.

3.

4,

5.

6.

Remove the rip fence and place the miter gauge in the left side groove.

Adjust the blade height so it is 1/8" higher than the top of the workpiece.

Hold the workpiece firmly against the miter gauge with the blade path in line with the desired cut location. Move the workpiece to one inch distance from the blade.

Start the saw and wait for the blade (1) to come up to full speed.

Keep the workpiece (2) against the face of the miter gauge (3) and flat against the face of the gauge and flat against the table. Then slowly push the workpiece through the blade (FIG. Z).

Do not try to pull the workpiece back with the blade turning. Turn the switch OFF, and carefully slide the workpiece out when the blade is completely stopped.

BEVEL CROSSCUTTING (FIG. BB)

This cutting operation is the same as crosscutting except

the blade is at bevel angle other than 0 °.

1.

Adjust the blade (1) to the desired angle, and tighten

the blade bevel lock knob.

2.

Always work to the left side of the blade. The miter

gauge (3) must be in the left side groove (2). It

cannot be used in the right side groove unless the

miter angle is very sharp, as it will interfere with the blade guard.

Fig. BB

2

1

,J/-------

\Pt

I.V.

]\

_-r" h

COMPOUND MITER CROSSCUTTING (FIG. CC)

This sawing operation combines a miter angle with a

bevel angle.

1.

Set the miter gauge (3) to the desired angle. Use

only the left side groove (2).

2.

Set the blade (1) bevel to the desired angle.

3,

Carefully push the miter gauge to begin the

cutting operation,

18

Fig. CC

3 2

Fig. EE

MITERING (FIG. DD)

This sawing operation is the same as crosscutting except the miter gauge is locked at an angle other than 90 °.

1.

Hold the workpiece (2) firmly against the miter gauge (3).

2.

Feed the workpiece slowly into the blade (1) to prevent the workpiece from moving.

Fig. DD

3

2 1

DADO CUTS (FIG. FF)

1.

The dado table insert is included with this saw.

Remove the saw blade, the blade guard, and the table insert. Install the dado and dado table insert.

2.

Instructions for operating the dado are packed with

the separately purchased dado set.

3.

The arbor (1) on this saw restricts the maximum

width of the cut to 1/2".

4.

It is not necessary to install the outside flange (2) before screwing on the arbor nut (3). Make sure that

the arbor nut is tight, and that at least one thread

of the arbor sticks out past the nut.

5.

Use only the 6" dado set and keep the width 1/2" or

less. It will be necessary to remove the blade guard

and splitter when using dado. Use caution when

dado is operating.

6.

Use onlythe correctnumber of roundoutside blades

and inside chippersas shownin the dado set's instruction

manual. Blade or chippermust not exceed 1/2".

7.

Check saw to ensure that the dado will not strike the housing, insert, or motor when in operation.

USING WOOD FACING ON THE RIP FENCE (FIG. EE)

When performing some special cutting operations, add

a wood facing (1) to either side of the rip fence (2):

1.

Use a smooth straight 3/4" thick wood board (1) that

is as long as the rip fence.

2.

Attach the wood facing to the fence with wood

screws (3) through the boles in the fence. A wood fence should be used when ripping material such as

thin paneling to prevent the material from catching between the bottom of the fence and the table.

For your own safety, always replace the blade, blade guard assembly, and blade insert when you are finished with the dado operation.

Fig. FF

I

iloll

J

J

/2

\

\

"3

19

MAINTAINING YOUR TABLE SAW

GENERAL MAINTENANCE

Fig. GG

For your own safety, turn the switch OFF and remove the switch key. Remove the plug from the power source outlet before maintaining or lubricating your saw.

!.

Clean out all sawdust that has accumulated inside the saw cabinet and the motor.

2.

Polish the saw table with an automotive wax to keep it clean and to make it easier to slide the workpiece.

3.

Clean cutting blades with pitch and gum remover.

4.

A worn, cut, or damaged power cord should be replaced immediately.

4

All electrical or mechanical repairs should be attempted

only by a trained repair technician. Contact the nearest

Sears Service Center for service. Use only identical replacement parts. Any other parts may create a hazard.

5.

Use liquid dish washing detergent and water to clean all plastic parts.

NOTE:

Certain cleaning chemicals can damage plastic parts.

6.

Avoid use of the following cleaning chemicals or solvents: gasoline, carbon tetrachloride, chlorinated solvents, ammonia and household detergents containing ammonia.

BLADE RAISING ANDTILTING MECHANISM

(FIG. GG)

After each five hours of operation, the blade raising mechanism and tilting mechanism should be checked for looseness, binding, or other abnormalities.

With the saw disconnected from the power source, turn the saw upside down and alternately pull upward and downward

on the motor unit. Observe any movement of the motor mounting mechanism.

Looseness or play in the blade raising screw (1) should be adjusted as follows:

1.

Using a wrench, loosen nut (2).

2.

Adjust nut (3) until it is finger-tight against the bracket (4), then back off the nut (3) 1/6 turn.

3.

Tighten nut (2) with the wrench, while holding nut (3) in place. Maximum allowable play of screw rod (1) is 4 mm.

Place a small amount of dry lubricant such as graphite or silicon on screw rod (1) at thrust washer (5). Do not oil threads of screw rods (1). Screw rod (1) must be kept clean and free of sawdust, gum, pitch, and other contaminants for smooth operation.

If excessive looseness is observed in any other part of the blade raising mechanism or tilting mechanism, take the complete unit to a Sears Service Center.

LUBRICATION

All motor bearings are permanently lubricated at the factory and require no additional lubrication.

On all mechanical parts of your table saw where a pivot or threaded rod are present, lubricate using graphite or silicone. These dry lubricants will not hold sawdust as would oil or grease.

20

TROUBLESHOOTING GUIDE

To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before making any adjustments.

• Consult your local Sears Service Center if for any reason the motor will not run.

SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION

Saw will not start.

Does not make accurate 45 ° and

90 ° rip cuts.

Material pinches blade when ripping.

1. Saw not plugged in.

2. Fuse blown or circuit breaker tripped.

3. Cord damaged.

1. Positive stop not adjusted correctly.

2. Blade tilt pointer not set accurately.

1. Plug in saw.

2.

Replace fuse or reset circuit breaker,

3.

Have cord replaced by a Sears

Service Center.

1. Check blade with square and adjust positive stop.

2.

Check blade with square and adjust pointer to zero.

1. Check and adjust rip fence.

2. Select another piece of wood.

Material binds on splitter.

Saw makes unsatisfactory cuts.

Material kicked back from blade.

Blade does not raise or tilt freely,

Blade does not come up to speed,

Machine vibrates excessively,

Does not make accurate

45 ° and 90 ° cross cuts.

1. Rip fence not aligned with blade.

2. Warped wood, edge against fence is not straight.

1. Splitter not aligned correctly with blade.

1, Dull blade.

2. Blade mounted backwards.

3. Gum or pitch on blade.

4. Incorrect blade for work being done.

5. Gum or pitch on table causing erratic feed.

1,

2.

3.

4.

5.

6.

7,

Rip fence out of alignment.

Splitter not aligned with blade.

Feeding stock without rip fence.

Splitter not in place.

Dull blade.

The operator letting go of material before it is past saw blade.

Miter angle lock knob is not tight.

1. Sawdust and dirt in raising and tilting mechanisms.

1. Extension cord too light or too long.

2. Low house voltage.

1. Saw not mounted securely to workbench.

2. Bench on uneven floor.

3. Damaged saw blade.

1. Miter gauge out of adjustment.

1. Check and align splitter with blade.

1. Replace blade.

2.

Turn blade around.

3.

1.

2.

3.

4.

5.

6.

7.

Remove blade and clean with turpentine and coarse steel wool.

4. Change the blade.

5. Clean table with turpentine and steel wool.

Align rip fence with miter gauge slot.

Align splitter with blade.

Install and use rip fence.

Install and use splitter (with guard).

Replace blade.

Push material all the way past saw blade before releasing work.

Tighten knob.

1. Brush or blow out loose dust and dirt.

1. Replace with adequate size cord.

2.

Contact your electric company.

1. Tighten all mounting hardware.

2.

Reposition on flat level surface.

Fasten to floor if necessary.

3.

Replace blade.

1. Adjust miter gauge.

21

1 2615BBDDS0

2

3

4

5

2501MBDN06

2705FBD106

14994501

2690MZD514

6A 14912206 B1

6 14912206

7 14994103

8

9

2570DBN606

14912301

10 14912906

11 14912801

12 14206901

13 14913201

14 14206601

15 14208001

16 2570DBN606

17 2615BBDD22

Oescr, ,,on K.,P.oNo

S'z. 2

Hex head screw M6"1.0-40 1 40 2501MBDN06 Flat washer 6 6"13-1

& washer 41

14212501

Spring

I

Fiat washer

Nut chuck

Warning label

Rivet

6"13-1

M6"I.0 T=6

1

I

1

2

42 14910208

43 14910104

44 14903101

45

26218BDA18

Rear clamp

Lockingrod

Insert

Pan head screw M5X0.8-12

!

1

2

Blade guard assembly

Blade guard

Caution label

Self-locking ring

Arm

Splitter

Bush

Roll pin

Bush

Kick back pawl

Kick back pawl

Self-locking ring

Hex head screw

& washer

M6"1.0-20

2

2

1

2

2

2

1

1

1

46

14962201

47 14962301

2 , 48

14960103

1 49 14962401

1

2

50 26378BDA70

51

19600101A2

52

53

54

14961601

2704FBD106

2651PBDK17

55 14961401

& washer

Side cover

Upper tube

Extension wing

Scale

Truss head round M6X1.0-23 neck screw

Locking handle assembly

Auxiliary fence

Square nut M6"1.0 T=5

Countersunk head M5"16-12 tapping

screw

Side cover

1

1

1

1

1

2

1

3

2

1

_

.

_ r-

"_

_

_o

_. o _ _1 _-I_11

Q._

_ _ _ _1 o 3 5"

_ _r-_l or_ =

,p

Z

r_

.Q _

-r c'< o

_ --.._,<

_

t_

_

_'_ O

_ _ _,

<__-I-n

_ 5"_ Go

_ ___>_'m

_ _ z o -_'_: a, _[__ r'

Ill

=

(D

"< _D 3

19

2536MBE613

20 14914701

21 14915401

22A 14910008A1

22 14910008

23

24

2601BBDA40

2504MBC006

25 14910505

Spring pin

Damper

Caution label

5-24

Parallel bracket assembly

Parallel bracket

Hex head bolt

External tooth

M6"1.0-16

6 6 lock washer

Width body

2

2

1

1

1

2

1

1

57 14961201

58 26028BLA25

59

19500203

60 2675BNHA42

61

14961001

62 2668BBDA23

63

14902909

& washer

Guide holder

Hex socket head M5"0.8-16

cap bolt

Clamp bolt

Pan head screw

Upper tube

M6X1.0-20

Pan head screw

Scale

M5"0.8-8

4

8

2

2

1

2

1

z _ _

c

E

5"-_ c

cb_(n

m -.: ¢D

_ _ _ o

_O--_

_ _ _ m o m=-.-_

"<

E_--I._

26 14212501

27

15218801

29 18622601

30 2641BBDA22

31 14916901

32A

14911301A1

32

14211203

Compression spring

Pointer

Round washer head screw

Grip

Bolt clamp assembly

Bolt clamp

M5"0.8-6

1

1

1

1

1

1

64 14902813

65 14915105

67 2504MBC006

68 2501NBDN16

69 14205001

70 2701FBD106

71

14914901

Table 1

Warning stick label

External tooth

M6"1.0-50

6 6 lock washer

Fiat washer 114"314-1116

1

1

Guard bracket

Hex. nut

Washer

M6"1.0 T=5

1

2

1

33 2701FBD113 Hex. nut M8*1.25,T=6.5

1 72 2604BBLA42

...............

...........................................................

Hex socket

...... ..................................................

35 14911007 Link 1 73 2801ABRG01 Strain relief

36 14917202

37 2660PBCK16

38 2536MBE627

39 2536MBE638

Spring plate

Pan head screw

Spring pin

Spring pin

MSX16-10

5-30

1

1

1

1

74

2636BBDAA9

75 2668BDDA43

76 2668BDDA44

180 2636BBDB48

181 280655545N

182 14994601

Countersunk head screw

Pan head screw

Pan head screw

Countersunk

Lead wire ass'y

Warning label

R ,< _-o

-_(_

_ o o_

_ 3

_ ,<

Q

_ o._(D

Gg_b_

_ _ _

_ •

M6"1.0-25 6 _"__'_N

................................

1 _D:_u

M6* 1.0-50

M6"1.0-55

4

1

1

1

1

1

_ _ o

_

=

_ ,_ r_

{:_

m

1-

_)

.._

_lCa

1,o

_1_

PJ

15

13

12

2

64

22A

44

48

43

42

41

40

5O

4g

56

54

52

61

27

32A

Z

0 rm

o_

_n

0

t_

Key Part

Description

Size

Qty

Size

Qty

Key Part

Description

1

111 18402702 Dust shield 4

77 14916901 Grip

1

112 2801DBHA04 Strain relief 2

78A 14911601A1 8olt clamp assembly

1

113 14902302 Switch box 1

78 14211201 Bolt clamp

114 14900136 Body shell 1

114"3/4-1116

1

79 2501NBDN16 Flat washer

115 14909401 Trade mark label 1

1

80A

14911402A5

80 14911402

Mitre gauge assembly

Mitre gauge

1

I

116 26688ZDA07

117

2504MZC004

Pan head screw

External tooth

lock washer

M4"0,7-8

6 4

3

3

81 14608001 Pin

1

82 14911802 Angle pointer

1

118 2853U55501 Circuit breaker 1

83 29835L5006 Steel ball

1

84 14523301 Com# spring

M6

0-10

1

SS 260388LA38 Hex socket set

1

86 14911707 Sheet bar

2

120

2653MBDE11

87 260888LA32 Hex socket truss he ad so'few

121A 2898D10G06 screw

Rocker switch 1

1

88 14937101

88A 14937101A2

89 257088N209

90 2536MBE605

91 2536MBE629

Wheel

Hand wheel assembly

E-ring

Spring pin

Spring pin

E-9

3-24

3-14

105 2138MBL704 Wrench hex

106

2138MBL709 Wrench hex

107A 28078806AFA1 Power cable assembly

1

2

2

1

1

1

121 2851D55G06

122 286058H101

123 14901704

124 2668BBDA32

125 2701FBD113

Rocker switch element

Switch key

Needle pointer

Pan head screw

Hex nut

1

M5"0.8-10 1

M8*1.25,T=6.5

1

..............................

92

93 14936501

94 2603BBLA36

95

14936701 bar

Parrie ring

Hex socket set screw M6"1.0-6

Caution label

2

4

1

"126"'"250"i"

Flat washer

127 14901503

128 14901103

129A 14900609A2

Pointer bracket

Height regulating bolt

Hand wheel assembly

8X16-2.5

1

1

1

11

96

2668BBDA39

104 14904402

Pan head screw

Wrench

M6"1.0-12

4

1

129 14900609 Whee_

97 2501NBDN12 Flat washer 114"518-1116 2

130 2703FMD108 Crown nut MS*l.25T=12-5 22

98 14906107 Warning label 1

131 14909001 Grip 2

99 2501NBDN16 Flat washer 1/4"314-1/16 4

132. 14900801 Bolt 2

100 2709FBDA02 Hexagon nut & flat washer 46

133 14900703 Clamp handle M10"1.5 T=8 2

101 2707FBN107

102 14903104

U-type nut

insert

134 2701FBD110

.............................................

15100801

Hex nut

Lock kno

•_

....................................

................

......................

11

136 2501NBDN16 Flat washer

......................

1

114.314-1116 1

137 14905804 Retaining clip 1

1

183 14994701 Warning label 1

107 28078B06AF

108 2801ABRF01

109 13601201

110 2660MBCE14

Power cable

Strain relief

Cord clamp

Pan head tapping screw

M4"16-16

1

2

Ol

104

_106

105 r m

109

111

116/_

117

118

112

113

93

\

B9

136

135

lZ9A k_

.,A

01

0

Key Part No.

Description Size ro

138

139

140

141

142

14930002

14930102

14930203

8387129942

2620BBDC18

Set nut

Arbor collar

Blade

Motor

Pan head screw

& washer

M5"0.8-12

143 14936201

144 14936301

Bearing seat

Shaft

..............................................................................................................................................................................

145 14935904 Stiffener

146 2708FBD107 Serrated toothed M6"1.0 T=6

147

148

149

150

14921307

14921403

2502NBC406

2708FBD107 hex. flange nut

Angle rod

Strap

Spring washer

Serrated toothed hex flange nut

6 1/4"

M6"1.0 T=6

151 14921001

152 14921703

153 2501NBDN03

154 2617BBLC11

155

156

157

2501NNHN34

14921802

14901203

Plunger housing

Bracket

Flat washer

Hex socket head

cap screw

Flat washer

Bracket

Saddle

3/16"3/8-0.022

M5"0.8-20

3/8"314-5/64 2

1

1

6

6

1

6

1

1

1

1

1

1

1

1

1

I

1

1

2

Qty Key Part No.

Description Size Qty

158 14901302

159 2603BBLA66

160 2701FBD111

161

2701FBD110

162 2615BBDD25

Spring

Hex. socketsetscrewM10*l.5-12

Hex. nut

Hex. nut

Hex head screw

& washer

163 2672BBDA40

Cap head square neck bolt

r ...................................................................................................................

164

2570BBN116 C-ring

165 14935102

166 14935001

Supporting plate

Nut

167 2672BBDA44

Cap head square neck bolt

M10"1.5 T=4

M10"1.5 T=8

M8"1.25-16

M6"1.0-16

A-16

M6"1.0-35

168 14922901

169 2701FBD106

170 2501NBDN09

Spacer

Hex nut

Flat washer

M6"1.0 T=5

1/4"3/4-7/64

171 2502ABC417

172

2701FBD106

173 2709FBDA02

6 6

M6"1.0 T=5

M6"1.0

174 14920003

175 14920301

176 2701FBD105

177 2615BBDC25

Flat washer

Hex nut

Hex nut

& flat washer

Motor bracket

Spacer

Hex nut

Hex head screw

and washer

MS*0.8T=4

M8"1.25-16

178 2672BBDB50 Cap head square neck bolt

179 2536MBE621

* 137218250001

Spring pin

Owner's Manual

M8"1.25-16

8-90

2

4

1

1

I

I

I

I

I

1

4

1

1

1

1

1

1

1

1

1

1

1

1

rm

0_ o

* Not Shown

¢O

Fo

QO

fo

¢n

O

147

/

148

/

149

/

/

150

r_

--4

155

156

153

164

165

166

167

169

171

172

141

140

139

138

"_

m

r-

m

(/)

CRAFTSMAN 10" TABLE SAW LEG STAND

PARTS LIST FOR SCHEMATIC D

Key

6

7

8

9

10

3

4

1

2

5

11

12

13

Part No.

17050106

2672BBDA54

17050407

2601BBDA69

14000304

2501MBDN 11

2701FBD109

2708FBD112

17050307

2601BBDA57

2501MBDN08

17050209

17050505

MODEL

Description

Size

Leg

Cap head square neck bolt

Bottom support bracket (long)

Hex head bolt

Spacer (foot pad)

M8x1.25-16

L=563

M 10xl .5-20

Flat washer

Hex nut

610x20-2

M10x1.5 T=8

Serrated toothed hexagon flange nut MSx1.25 T=7.5

Upper support bracket (short)

Hex head bolt

L=413

M8xl.5-30

Flat washer

Upper support bracket (long)

Bottom support bracket (short)

68x16-2.5

L=491

L=475

NO. 137.218250

Qty

4

4

20

2

4

4

16

2

4

4

4

2

2

28

CRAFTSMAN

SCHEMATIC D

10" TABLE SAW

12

<

10

11

MODEL NO. 137.218250

9

13

2

3

7

6

5

4

29

CO

11

12

13

14

15

6

7

8

9

10

Key

4

5

1

2

3

16

17

18

19

20

21

22

23

24

25

, ,.-

Part No.

2620B8DB26

83871271

2603BBLA23

87840021

83962491A1

83990291A1

83990301

87840081

83870111A2

2662MZDE41

87840131

87840122A2

83871141

2801UBHA07

83871161

2001AH1010

2570BBN117

87840171

83871201

2001 LU6204

83870221

2504MZF004

2636BZDA07

2571MNC252

83870253

Description

Pan head screw

Support plate

Hex socket set screw

Motor housing

Brush holder assembly

Brush assembly

Brush cover

Bearing bushing

Field assembly

Pan head tapping screw

Baffle

Armature assembly

Motor nameplate

Strain relief bushing

Bracket

Needle bearing

C-ring

Helix gear

Collar

Ball bearing

Bearing retainer

External tooth lock washer

Countersunk head screw

Parallel key

Arbor shaft

Size

MSX0.8-30

M5X0.8-8

M5X12-60

6204LLU

64

M4x0.7-8

Qty

4

1

2

1

2ST

2ST

2

1

1

2

1

1

1

1

1

1

1

1

1

4

4

1

1

1

1

!

.=

III

23

io

CO

01 o

08

O0

01

0

32

o_

\

i

c!tof

push 1/4 wood.

Cut off here to push 1/2" wood.

Notch to help prevent hand from slipping.

J

1/2" Squares.

PUSH STICK

Make from 1/2" or 3/4" wood or thickness less than width of material to be cut.

CAUTION!

Use only good strong wood or plywood.

Use a jigsaw or bandsaw to cut out.

\

\

Optional hanging hole.

ii_ii

For repair of major brand appliances in your own home...

no matter who made it, no matter who sold it!

1-800-4-MY-HOME sM

Anytime, day or night

(1-800-469-4663)

www.sears.com

To

bring in products such as vacuums,

lawn equipment and electronics

_:_:_:_!!iiii!_i

for repair, call for the location of your nearest Sears Parts & Repair Center. !!!!_!i!i!!

......

1-800-488-1222

Anytime, day or night

::::::::_::: www.sears.com

r:::::::_:::::

:.:*:.:.:.:.:.:

_.::_::::::::,:

iii!i!iiiill

ii!iiiiiiiiiiil

For the replacement parts, accessories and owner's manuals that you need to do-it-yourself, call Sears PartsDirect "_ !

1-800-366-PART

6am- 11pm

CST,

(1-800-366-7278) 7 days a week

:,:4:,::: www.sears.com/partsdirect

To purchase or inquire about a Sears Service

Agreement:

1-800-827-6655

7 a.m. - 5 p.m. CST, Men. - Sat.

iiiiiiiiiiii_

:.:.7:.:,:,:,:

:,::::::

:._:*:.>_:,:

::_:::::::t:_:

_:_::::::::::::

:::::::_

Para pedir servicio de reparacibn a dornicilio,

y para ordenar piezas con entrega a domicilio:

Au Canada pour service en franc_ais: _:_:_:_:_:_............

:::::::

1 877 LE FOYER _" .............

::.:::.:.:

1-888-SU-HOGAR s.

(1-888-784-6427)

.... [°°'°°

HomeCentral"

(1 877 533-6937)

!

:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::

...............

:ii_;!_!:!

::::::::

® Regislered T_ademark I "

Trademark o€ Seam. Roebuck and Co.

® Marca Regist rada I

TM

Marca de F&bnca de Sears, Roebu_:k and CO.

© Se_rs, Roobuck and Co.

3/2000