GE 24999 Universal Remote Instruction manual

Universal Remote

Instruction Manual

24999

Table of Contents

Introduction............................................................................................................................3

Button.Functions.................................................................................................................4

.

DVD/DVR.Punch-Through.Feature.....................................................................5

Setup.........................................................................................................................................6

.

Battery.Installation....................................................................................................6

.

Battery.Saver................................................................................................................6

.

Code.Saver....................................................................................................................6

.

Power-On.default.......................................................................................................6

.

Liquid.Crystal.Display.(LCD)....................................................................................6

.

Code.Setup....................................................................................................................6

Setup.........................................................................................................................................7

Code.Entry..............................................................................................................................8

.

Code.Entry.Using.On-Screen.Code.List............................................................9

.

Direct.Code.Entry........................................................................................................8

.

Searching.For.Codes.................................................................................................9

Code.Identification.Feature............................................................................................9

Programming.Combo.Device.Codes..........................................................................9

Volume/Mute.Control.Feature.................................................................................... 10

Setting.Volume/Mute.Control,.Punch-Through.................................................. 10

Setting.any.Mode.to.use.its.own.Volume/Mute................................................. 10

Resetting.Mute/Volume.Control.to.defaults........................................................ 11

Setting.Time.of.Day......................................................................................................... 12

Setting.the.Date................................................................................................................ 12

Setting.the.Backlight.Delay.......................................................................................... 13

Full.System.Reset.to.factory.defaults..................................................................... 13

Timer.Setup......................................................................................................................... 14

.

Sleep.Timer................................................................................................................. 14

Setting.and.Clearing.Timers................................................................................. 14-15

Code.Learning.................................................................................................................... 16

.

Tips.on.Learning....................................................................................................... 16

Learning.Commands...................................................................................................... 18

Clearing.Commands....................................................................................................... 19

.

Clearing.Learned.commands.for.a.mode.................................................... 19

.

Master.Clear............................................................................................................... 19

Troubleshooting................................................................................................................ 20

2

Introduction

Congratulations.on.your.purchase.of.this.24999.Universal.Remote.

Control..It.is.one.of.the.most.unique.looking,.and.easy.to.use.remote.

controls.available.today..Its.stylish.looking.blue.backlight,.and.metallic.

keypad.is.like.no.other.remote..With.the.24999.juggling.multiple.remote.

controls.is.a.thing.of.the.past!.Your.24999.Universal.Remote.controls.

up.to.8.devices,.including.the.most.popular.brands.of.TV,.VCR,.DVD,.SAT,.

CBL,.and.audio.equipment..

Note:.Some.functions.from.your.original.remote.may.not.be.controlled.

by.the.24999.remote..Use.the.original.remote,.if.available,.to.control.

such.functions..Sometimes.buttons.other.than.described.in.these.

instructions.may.actually.perform.the.function..For.example,.the.CHAN.

and.VOL.buttons.might.be.used.to.navigate.through.menu.choices..

We.recommend.you.experiment.with.the.remote.to.identify.if.such.

situations.pertain.to.your.equipment..

The.24999.Universal.Remote.is.easy.to.use,.easy.to.program,.and.it.

gives.you.total.control—at.the.touch.of.your.fingertips!

3

Button Functions

8.

9.

6.

7.

10.

3.

4.

1.

2.

5.

11.

12.

13.

Note:.The.

REC button.must.be.pressed.TWICE.to.record.from.your.

device..For.some.brands.of.VCRs,.you.might.need.to.press.the.

REC button.once,.then.press.it.again.for.three.seconds.

Some.buttons.on.the.remote.might.have.functions.that.are.referred.

to.by.different.names.on.the.device.you.are.controlling..E.G..

LAST.may.

be.called.RECALL,.or.

ENTER may.be.called.DISPLAY..These.differences.

depend.on.the.brand.and.model.of.your.product..Also,.this.remote.can.

only.operate.features.that.exist.on.your.product..E.G.,.your.product.

must.have.

LAST.ability.for.the.LAST button.to.operate.this.feature.

4

21.

20.

19.

18.

17.

26.

25.

24.

23.

22.

16.

15.

14.

Button Functions, cont.

1. Liquid Crystal Display (LCD): Helps.with.setup.and.displays.the.

Mode.the.remote.is.in,.and.time,.etc.

2. SETUP: Used.for.setting.up.your.remote.

3. TV, DVD, DVR, etc.:.Selects.product.to.be.operated.

4. EXIT:.Exits.On-Screen.Menus/Returns.to.previous.On-Screen.

selection.

5. Dot:.Used.for.digital.channels,.e.g..2.3..

6. MENU: Brings.up.the.device.Menu.screen.(if.available).-.use.with.

UP,.DOWN,.LEFT,.and.RIGHT navigation.buttons.

7. MUTE: Turns.off.the.TV.sound.while.the.picture.remains.

8. . UP,.DOWN,.LEFT &.RIGHT: Navigation.buttons.

9. VOLUME UP/DOWN: Changes.the.volume.level.of.the.product,.

normally.the.TV.

10. OK: Selects.menu.items.for.the.device.you.are.controlling.

11. ABCD buttons:.Used.to.store.learned.commands.

12.. REPLAY: On.some.DVRs,.this.button.replays.the.last.8.seconds.of.a.

program.

13.. PAGE DOWN: Sets.your.Favorites.ratings,.and.moves.one.screen.

down.at.a.time.in.guides.and.menus.

14. RECORD, PLAY, STOP, REW, FF, PAUSE:.Control.buttons.that.

operate.your.DVD/DVR.even.when.the.remote.is.set.to.operate.the.

TV..Also.operates.DVD.Scan.-/+.

15. LIVE:.Returns.to.live.TV.

16.. PAGE UP:.Sets.your.Favorites.ratings,.and.moves.one.screen.up.at.

a.time.in.guides.and.menus.

17. INPUT: For.some.TVs,.press.repeatedly.to.select.available.viewing.

sources.(antenna,.cable.box,.VCR,.DVD,.etc.).

18. DVR List:.Press.to.display.list.of.recorded.shows.on.your.DVR.

19. CHANNEL UP/DOWN: Changes.the.channels..Also.controls.DVD/

CD.CHAPTER.+/-.track.selection,.i.e.,.DVD/CD.Track.Skip.Up/Down..

Note.the.

DVR buttons.also.control.the.DVD.when.in.DVD.Mode.

20. LAST:.Returns.to.the.previously.selected.channel,.or.DVD.repeat.

toggle..

21. INFO: Displays/selects.on-screen.channel.information.

22. GUIDE:.Displays.on-screen.program.or.channel.guides.

23. ENTER:.Used.after.direct.channel.number.entry.to.immediately.

change.to.the.selected.channel.

24. NUMBERS:.Enter.numbers.for.direct.channel.selection..Some.

products.require.Enter.to.be.pressed.after.channel.selection.

25. ASPECT: Aspect.Ratio.Control.selects.viewing.format.for.the.

displayed.picture,.e.g.,.Wide,.Zoom,.etc.

26. POWER: Turns.device.on.or.off.

DVD/DVR Punch-Through Feature

This.remote.allows.the.6.DVD/DVR.transport.buttons.(i.e.,.PLAY,.PAUSE,.

STOP,.FF,.REWIND,.and.REC).to.operate.the.programmed.TV,.DVD,.

SAT,.DVR,.Cable.device.if.the.code.has.these.button.functions.e.g..if.

you.have.programmed.a.SAT/DVR.or.Cable/DVR,.etc..Otherwise.the.

transport.keys.will.punch-through.to.the.last.DVD.or.VCR.programmed.

mode.you.used,.i.e.,.the.transport.buttons.control.your.DVD.or.VCR.

player.even.when.you.are.in.TV,.SAT.or.Cable.mode.

5

Setup

Battery Installation

1..On.the.back.of.the.remote,.push.down.on.the.

tab.and.lift.the.cover.off.

2..Match.the.batteries.to.the.+.and.-.marks.inside.

the.battery.case,.then.insert.2.AAA.Alkaline.

batteries.

3..Press.the.battery.cover.back.into.place.

Battery Saver

Your.remote.automatically.turns.off.if.the.buttons.

are.depressed.more.than.30.seconds..This.will.

save.your.batteries.should.your.remote.get.stuck.

in.a.place.where.the.buttons.remain.depressed.

(e.g.,.between.the.sofa.cushions).

Code Saver

All.user.programmed.settings,.except.Time,.Day,.and.Date.will.be.stored.

in.permanent.memory.while.you.are.changing.batteries,.so.you.will.not.

lose.any.codes.stored.in.the.remote.while.you.are.changing.batteries..

Time,.Day,.and.Date,.will.be.cleared.to.the.factory.defaults.when.the.

batteries.are.replaced.

Power-On Default

The.remote.powers.on.in.TV.mode.

Liquid Crystal Display (LCD).

The.LCD.lets.you.see.at.a.glance.what.mode.the.remote.is.in..It.also.

includes.a.clock.that.displays.the.time.and.day,.and.a.visual.indication.

that.the.remote.is.transmitting.when.you.press.a.button.

Code Setup

The.

SETUP.button.is.used.to.setup.the.remote..You.can.either.setup.the.

remote.using.the.code.for.your.brand.of.product,.from.the.code.tables.

(on.separate.sheet),.or.you.can.search.through.the.library.of.codes.until.

you.find.a.code.that.works.for.your.product.

You.can.store.any.kind.of.code.under.any.mode.(except.TV)..I.E..you.can.

store.a.VCR.code.under.the.

CBL button,.or.a.DVD.code.under.the.VCR button,.etc..However,.you.can.only.store.TV.codes.under.the.

TV button.

The SETUP button.is.used.for.programming.the.remote.and.accessing.

any.additional.features.-.e.g..Shifted.functions,.see.below..To.enter.setup.

mode,.press.and.hold.the.

SETUP button.until.“CODE.SETUP”.appears.in.

the.display..The.“SET”.symbol.will.always.be.shown.when.the.remote.is.

in.Setup..Successive.presses.of.the.

SETUP button.shows.available.Setup.

options.in.the.order.shown.below..

1..CODE.SETUP.–.press.

OK here.to.program.a.Mode.e.g..Code.Entry,.

Search,.etc..See.Code.Setup.options.below.

2..SYSTEM.SETUP.–.press.

OK here.to.set.Time,.Date,.Volume.Control,.etc..

3..TIMER.SETUP.–.press.

OK here.to.set.Timer.events.

4..LEARN.SETUP.–.press.

OK here.to.program.a.Mode.with.Learned.

commands.

5..EXIT.SETUP.–.press.

OK here.to.Exit.Setup.routines.and.return.to.

normal.operation.

Press.

OK to.select.the.desired.programming.step.required..

Exit.from.Setup.occurs.automatically.after.approximately.15.seconds.if.

no.buttons.is.pressed..TIME.OUT.is.displayed.

When.the.remote.is.busy.processing.in.Setup.routines,.“Please.Wait”.is.

displayed.

6

Setup, cont.

Setup Screen Navigation.Use.the.SETUP,.OK,.and.Up,.Down,.Left.and.

Right.navigation.buttons.for.Setup.screen.navigation.and.selection..

To.exit.the.Setup.routines.and.return.to.normal.operation,.press.the.

EXIT button.or.navigate.to.the.“EXIT.SETUP”.screen.and.press.OK..

Completion.of.some.Setup.routines.will.automatically.return.the.remote.

to.normal.operation.

Mode button press Display.Pressing.and.holding.a.Mode.button.

changes.to.that.Mode.and.displays.the.active.Mode.and.its.code,.e.g.,.

DVD.and.the.programmed.4-digit.code.e.g.,.0768..The.display.returns.to.

normal.when.you.release.the.button.

SETUP (Shift) Display.Pressing.and.releasing.the.Setup.button.displays.

the.active.Mode.of.the.remote.e.g..DVD,.the.Date.e.g..3:26.(Month:Day).

and.indicates.“Shift”.operation.with.“(S)”..Press.and.release.Exit.to.return.

to.normal.display..To.use.the.

SETUP button.for.Shift.-.Press.and.release.

SETUP followed.by.the.desired.secondary.function.button.

7

Code Entry

Code Setup Options:.Pressing.OK at.the.CODE.SETUP.screen.presents.

3.options.for.programming.a.Mode.with.codes..These.are.LIST.CODES.

(lets.you.enter.a.4.digit.code.from.the.on-screen.code.list),.ENTER.CODES,.

(lets.you.enter.a.4.digit.code.directly.from.the.printed.code.list).SEARCH.

CODES,.(lets.you.search.through.the.codes.stored.in.the.remote.to.find.

the.correct.one.for.your.device).

Code Entry using On-screen Code List

1..Manually.turn.on.the.device.to.be.controlled.

2..Press.and.hold.the.

SETUP button.until.CODE.SETUP.is.displayed.

(takes.about.3.seconds),.then.release.the.

SETUP button.

3..Press.and.release.

OK..LIST.CODES.is.displayed.


OK..MODE.KEY?.is.displayed.

5..Press.and.release.the.desired.mode.button.( TV,.VCR,.DVD,.etc.)..The.

Mode.is.displayed.along.with.its.currently.programmed.code..

6..Using.the.

UP/DOWN.buttons,.select.the.Device.type.to.be.

programmed.( TV,.VCR,.DVD,.etc..Note - For TV Mode, only a TV

Device can be selected.


OK to.confirm.selection..

8..The.Code.List.Brand.and.Code.will.now.be.displayed.(e.g..Admiral.

0000)..Use.the.

UP/DOWN.buttons.to.select.the.Brand.and.LEFT/

RIGHT.buttons.to.select.the.Code..Codes.can.be.tested.on.your.

device.using.

VOLUME, MUTE, CHANNEL, POWER, INPUT, PLAY,

STOP, FF, REWIND and.PAUSE. Once.the.correct.code.has.been.

found,.press.and.release.

OK to.install.the.Code..

9..PLEASE.WAIT.is.briefly.displayed,.followed.by.SUCCESS.and.the.

remote.returns.to.normal.operation..

10..With.your.device.on,.press.

CHANNEL UP..If.the.device.responds,.

no.further.programming.is.required..Note:.If.some.buttons.do.not.

operate.your.equipment,.try.one.of.the.other.codes.for.your.brand.

of.device..

Direct Code Entry

1..Manually.turn.on.the.device.to.be.controlled.


SETUP.button.until.CODE.SETUP.is.displayed.

(takes.about.3.seconds),.then.release.the

SETUP.button.



4..Press.the.

DOWN navigation.button.until.ENTER.CODES.is.displayed..


OK..MODE.KEY?.is.displayed.

6..Press.and.release.the.desired.mode.button.( TV, VCR,.DVD,.etc.)..The.

Mode.is.displayed.along.with.its.currently.programmed.code.

7..Enter.the.4.digit.code.from.the.code.tables.(on.separate.sheet)..After.

the.4th.digit.is.entered.SUCCESS.is.displayed.and.the.remote.returns.

to.normal.operation..

If.an.invalid.code.is.entered,.CODE.ERROR.is.shown.in.the.display.and.

the.remote.returns.to.normal.operation..

8..With.your.device.on,.press

CHANNEL UP..If.the.device.responds,.

no.further.programming.is.required..Note:.If.some.buttons.do.not.

operate.your.equipment,.try.one.of.the.other.codes.for.your.brand.

of.device.

8

Code Entry, cont.

Searching for Codes

If.your.product.does.not.respond.after.you.have.tried.all.the.codes.for.

your.brand,.or.if.your.brand.is.not.listed,.try.searching.for.your.code.by.

following.these.steps.

1..Manually.turn.on.the.device.( TV,.VCR,.DVD,.etc.).to.be.controlled.




SETUP.button.



4..Press.the.down.navigation.button.repeatedly.until.SEARCH.CODES.is.

displayed.


OK..MODE.KEY.is.displayed.

6..Press.and.release.the.desired.mode.button.( TV, VCR,.DVD,.etc.)..

DEVICE?.TV.is.displayed.

7..Using.the.Up/Down.keys,.select.the.Device.type.to.be.programmed.

(TV,.VCR,.DVD,.etc..

Note - For TV Mode, only a TV Device can be selected.


OK to.confirm.selection..SEARCH.KEY?.is.displayed..

9..Press.the.

CHANNEL UP.button.(or.POWER,.or.PLAY for.VCRs/

DVDs).repeatedly.(up.to.300.times).until.the.Device.to.be.controlled.

changes.channel,.turns.off.or.responds.accordingly..SEARCHING.

is.displayed.(along.with.the.Device.selection).during.the.search.

process..If.the.desired.Code.is.accidentally.passed.then.press.the.

CHANNEL DOWN.button.to.backtrack.through.the.Library..Press.

CHANNEL UP.(or.POWER.or.PLAY).to.change.direction.forward.again..


OK to.install.the.Code..PLEASE.WAIT.is.briefly.

displayed,.followed.by.SUCCESS.and.the.remote.returns.to.normal.

operation.

Notes:

1..If.the.Device.does.not.have.a.

CHANNEL UP button,.use.PLAY (VCR/DVD).

or.the.

POWER button.instead.

2..Code.Search.starts.from.the.currently.stored.4-digit.number.under.

that.Mode.

3.. When. all. codes. have. been. searched. SEARCH. END. is. displayed. and.

remote.returns.to.normal.operation.

Code Identification Feature

Press.and.hold.the.respective.Mode.key.in.normal.operation.to.display.

the.programmed.code.for.that.Mode.e.g.,.DVD.Code.0768.

Programming Combo Device Codes

Some.combo.(combination).devices.(TV/DVR,.TV/DVD,.DVD/DVR,.etc.).

require.you.to.set.up.2.different.modes.to.control.both.parts.of.the.

combo..For.example,.if.you.have.a.TV/DVD.combo,.you.might.need.to.

set.up.one.code.under.the.TV.mode.to.control.the.TV.and.a.separate.

code.(under.other.modes).to.control.the.DVD.

9

Setup, cont.

System Setup Options

Pressing.

OK at.the.SYSTEM.SETUP.screen.accesses.the.System.Setup.

Options.for.Volume.Punch-Through.control.Setup,.Time.Setup,.Date.Setup,.

Backlight.Setup.and.System.Reset.

Volume/Mute Control and Punch-Through Feature

Your.remote.allows.you.to.select.which.device.mode.controls.VOLUME.

and.MUTE..This.remote.is.initially.set.for.all.device.modes.to.use.their.

own.Volume/Mute.control.if.present..If.the.programmed.code.does.not.

have.Volume/Mute.operation,.then.VOLUME.and.MUTE.will.“punchthrough”.(hand-over).control.to.the.TV.mode.device.without.you.

needing.to.change.to.TV.mode..Note:.Any.mode.chosen.for.Volume/

Mute.control.must.have.its.own.Volume/Mute.function.or.else.VOLUME.

and.MUTE.will.not.function.

Setting ALL Volume/Mute Control to any one Mode (ALL VOL. SET)

This.routine.can.set.all.Modes.to.“punch-through”.to.any.one.chosen.

Mode.for.Volume/Mute.button.control.without.needing.to.change.to.

that.Mode.




SETUP.button.

2..Press.the.down.navigation.button.until.SYSTEM.SETUP.is.displayed..


OK..VOL/MUTE.SETUP.is.displayed.


OK..ALL.VOL..SET.is.displayed.


OK..ALL.VOL..MODE?.is.displayed.

6..Press.and.release.desired.Mode.key.(TV,.VCR,.DVD,.etc.).for.Volume/

Mute.control..PLEASE.WAIT.is.briefly.displayed,.followed.by.SUCCESS.

and.the.remote.returns.to.normal.operation.

All. Modes. will. now. punch-through. to. your. chosen. Mode. for. Volume/

Mute.control..If.the.chosen.Mode.has.no.Volume/Mute.commands.of.its.

own,.“Volume.Error”.is.shown.in.the.display.and.the.remote.returns.to.

normal.operation..

Setting any Mode to use its own Volume/Mute Control (MODE VOL.

SET)

This.sets.any.Mode.to.use.only.its.own.Volume/Mute.control,.i.e..

Volume/Mute.punch-through.is.disabled.for.this.Mode..Note.-.If.your.

chosen.Mode.has.no.Volume/Mute.functions.of.its.own.then.the.

Volume/Mute.buttons.will.do.nothing.




SETUP.button.






5..Press.the.down.navigation.button.until.MODE.VOL..SET.is.displayed.


OK..MODE.VOL..MODE?.is.displayed.

7..Press.and.release.desired.Mode.key.(TV,.VCR,.DVD,.etc.).to.be.disabled.

for.Volume/Mute.punch-through.control..PLEASE.WAIT.is.briefly.

displayed,.followed.by.SUCCESS.and.the.remote.returns.to.normal.

operation.

The.chosen.Mode.will.now.use.its.own.Volume/Mute.control.

10

Setup, cont.

Resetting Volume/Mute Control to Factory Defaults (VOL/MUTE

RESET) This.resets.Volume/Mute.control.back.to.its.Factory.default.

settings..




SETUP.button.






5..Press.the.down.navigation.button.repeatedly.until.VOL/MUTE.RESET.

is.displayed.


OK..CONFIRM.RESET.is.displayed.


OK..PLEASE.WAIT.is.briefly.displayed,.followed.by.

SUCCESS.and.the.remote.returns.to.normal.operation.

Volume/Mute.control.is.now.rest.to.its.Factory.default.settings.

11

Setup, cont.

Setting the Time of Day (TIME SETUP) To.set.the.Time.of.day.for.normal.

LCD.time.display..




SETUP.button.




4..Press.the.down.navigation.button.until.TIME.SETUP.is.displayed.


OK..TIME?.is.displayed.showing.current.format.(12.

or.24.hour).flashing.and.current.time.

6..Use.the.Up/Down.navigation.buttons.to.set.the.format.(12Hr.or.24Hr).

then.press.and.release.

OK.

7..The.“hours”.will.be.flashing..Use.the.Up/Down.buttons.to.set.the.hours.

(keep.going.past.12.to.select.PM.hours).then.press.and.release.

OK..

8..The.“minutes”.will.be.flashing..Use.the.Up/Down.buttons.to.set.the.

minutes.then.press.and.release.

OK.

9..SUCCESS.is.displayed..The.remote.remains.in.Setup.Mode,.returning.to.

the.CODE.SETUP.screen..Press.

EXIT then.OK to.exit.Setup.Mode..PLEASE.

WAIT.is.briefly.displayed,.then.the.remote.returns.to.normal.operation.

Setting the Date (DATE SETUP) To.set.the.Month,.Date.and.Day..


SETUP.button.until.CODE.SETUP.is.displayed.(takes.

about.3.seconds),.then.release.the

SETUP.button.




4.. Press. the. down. navigation. button. repeatedly. until. DATE. SETUP. is.

displayed..


OK..YEAR?.is.displayed.with.the.last.2.year.digits.

flashing..

6..Use.the.Up/Down.buttons.to.set.the.Year.then.press.and.release.OK.

7..MONTH?.is.displayed.with.the.Month.digits.flashing..Use.the.Up/Down.

buttons.to.set.the.Month.then.press.and.release.

OK.

8.. DATE?. is. displayed. with. the. Date. digits. flashing.. Use. the. Up/Down.

buttons.to.set.the.Date.then.press.and.release.OK.

9..DAY?.is.displayed.with.the.Day.flashing..Use.the.Up/Down.buttons.to.

set.the.Day.then.press.and.release.

OK.

10..SUCCESS.is.displayed,.and.the.remote.remains.in.Setup.Mode,.returning.

to.the.CODE.SETUP.screen..Press.

EXIT then.OK to.exit.Setup.Mode..

PLEASE.WAIT.is.briefly.displayed,.then.the.remote.returns.to.normal.

operation.

12

Setup, cont.

Setting the Backlighting On time (BACKLIGHT SETUP).To.set.the.length.

of.time.the.Backlighting.remains.on.after.you.stop.pressing.buttons.




SETUP.button.




4..Press.the.down.navigation.button.repeatedly.until.BACKLIGHT.SETUP.

is.displayed..Press.and.release.

OK.

5..BACKLIGHT.TIME?.is.displayed.with.the.current.Backlight.On.time.digits.

flashing.. Use. the. Up/Down. buttons. to. set. the. Backlight. On. time. in.

increments.of.5.seconds.up.to.a.maximum.of.60.seconds..The.default.

Backlight.On.time.is.10.seconds..To.turn.the.Backlighting.feature.off,.

set.the.time.to.“00”.(zero)..Press.and.release.

OK.

6..SUCCESS.is.displayed.and.the.remote.remains.in.Setup.Mode,.returning.




operation.

Reset the LCD Remote to Factory Defaults (SYSTEM RESET) To.reset.

the.remote.back.to.factory.default.settings..All.User.programmed.

settings,.e.g..code.settings,.learned.commands,.etc.,.are.cleared.to.their.

respective.default.settings..




SETUP.button.




4..Press.the.down.navigation.button.repeatedly.until.SYSTEM.RESET.is.

displayed..Press.and.release.

OK.

5..CONFIRM.RESET.is.displayed..Press.and.release.

OK.

6..PLEASE.WAIT.is.displayed.while.all.settings.are.Reset.then.the.remote.

exits.Setup.and.returns.to.normal.operation.

13

Setup, cont.

Timer Setup

Pressing.

OK at.TIMER.SETUP.accesses.the.available.Timer.Options..

These.are.a.TV.Sleep.Timer.and.4.Timers.that.can.send.a.sequence.of.

up.to.3.key.commands.at.the.preset.time.

Setting and Clearing a TV Sleep Timer (TV Sleep Setup)

The.remote.can.be.programmed.with.a.TV.Sleep.Timer..At.the.end.of.

the.set.Timer.period,.the.remote.sends.the.Power.command.for.the.

TV.Mode.device..The.TV.Sleep.Timer.can.be.set.for.a.period.of.1-90.

minutes..The.“Zzz”.symbol.is.displayed.when.a.TV.Sleep.Timer.is.set.

To set a TV Sleep Timer (no “Zzz” in normal display)

1..Turn.on.the.TV.Mode.device.




SETUP.button.

3.. Press. the. down. navigation. button. repeatedly. until. TIMER. SETUP. is.


OK.

4..TV.SLEEP.SETUP.is.displayed..Press.and.release.

OK.

5..TV.SLEEP.SET.is.displayed..Press.and.release.

OK.

6..TV.SLEEP.TIME?.is.displayed.with.“minutes”.flashing..Use.the.Up/Down.

buttons.to.set.the.minutes.then.press.and.release.

OK.

7..SUCCESS.is.displayed..The.remote.remains.in.Setup.Mode,.returning.to.



WAIT.is.briefly.displayed,.then.the.remote.returns.to.normal.operation..

Zzz.is.displayed.on.the.screen.to.indicate.that.a.Sleep.Timer.is.set.

To clear a TV Sleep Timer (“Zzz” in normal display)




SETUP.button.



OK.

3..TV.SLEEP.SETUP.is.displayed..Press.and.release.

OK.

4..TV.SLEEP.CLEAR.is.displayed..Press.and.release.

OK.

5..CONFIRM.CLEAR.is.displayed..Press.and.release.

OK.

6..SUCCESS.is.displayed.and.the.remote.remains.in.Setup.Mode,.returning.




operation.

Setting and Clearing Timers (TIMER SETUP)

The.remote.can.be.programmed.with.up.to.4.Timers.(Timer.1,.2,.3.&.4)..

Each.Timer.can.be.assigned.up.to.2.keys.to.activate.at.the.set.time..The.

first.key.must.always.be.a.Mode.key..Subsequent.keys.cannot.include.

Up,.Down,.Left,.Right,.OK,.Exit,.Setup.or.any.Mode.key..Timers.can.only.

activate.within.the.following.24-hour.period..Timers.are.automatically.

cleared.after.activation..The.“Timer.Bell”.symbol.is.displayed.when.any.

Timer.is.set.

14

Setup, cont.

To set a Timer (Note, the Timer must be cleared first if it was previously set – see To Clear a Timer below)

1.. Press.and.hold.the.



SETUP.button.


displayed..

3.. Press.and.release.

OK..TV.SLEEP.SETUP.is.displayed..

4.. Press. the. down. navigation. button. until. TIMER. X. SETUP. is. displayed.

(where.“X”.is.1,.2,.3.or.4)..Press.and.release.

OK.

5.. TIMER.X.SET.is.displayed..Press.and.release.

OK.

6.. TIMER.X.TIME?”.is.displayed.with.the.“hours”.flashing..Use.the.Up/Down.

buttons.to.set.the.hours.(keep.going.past.12.to.select.PM.times).then.

press.and.release.

OK.

7.. The.“minutes”.will.be.flashing..Use.the.Up/Down.buttons.to.set.the.

minutes.then.press.and.release.

OK.

8.. TIMER.X.MODE?.is.displayed..Press.and.release.the.desired.Mode.key.

(TV,.VCR,.DVD,.etc.).

9.. TIMER.X.Key1?.is.displayed..Press.and.release.the.key.required.(e.g..

POWER).

10.. SUCCESS.is.displayed..The.remote.remains.in.Setup.Mode,.returning.to.



WAIT.is.briefly.displayed,.then.the.remote.returns.to.normal.operation..

A.“Timer.Bell”.is.displayed.on.the.screen.to.indicate.that.a.timer.is.set.

To clear a Timer (“Timer Bell” in normal display)




SETUP.button.


displayed..

3.. Press.and.release.

OK..TV.SLEEP.SETUP.is.displayed..

4.. Press.the.down.navigation.button.until.the.desired.TIMER.X.SETUP.is.

displayed.(where.“X”.is.1,.2,.3.or.4).screen..Press.and.release.

OK.

5.. TIMER.X.CLEAR.is.displayed..Press.and.release.

OK.

6.. CONFIRM.CLEAR.is.displayed..Press.and.release.

OK.

7.. SUCCESS.is.displayed..The.remote.remains.in.Setup.Mode,.returning.to.



WAIT.is.briefly.displayed,.then.the.remote.returns.to.normal.operation.

15

Code Learning

Tips On Learning

You.can.only.learn.one.device.type.under.any.one.Mode.button.e.g..

only.learn.TV.codes.under.the.

TV Mode,.DVD.codes.under.the.DVD

Mode,.etc..If.you.are.trying.to.learn.from.a.“Universal”.remote,.it.might.

have.more.than.one.code.type.stored.under.a.Mode..Try.learning.from.

another.remote.to.see.if.there’s.a.problem.with.the.type.or.brand.of.

remote.you.are.trying.to.learn.from..

a. Some functions from some types of remotes might not be able to be learned.

b. No functions may be stored under the SETUP button.

c. Only one original device type can be learned per individual Mode.

d. Use.fresh.batteries.for.both.the.Learning.Remote.and.the.Original.

Remote.

e. Do.not.attempt.to.Learn.directly.under.an.incandescent.or.

low-energy.light.as.these.can.cause.interference.with.the.IR.

transmissions..Keep.at.least.3.feet.away.from.any.such.light.sources.

f. Perform.a.Master.Clear.(see.page.22).before.learning.and.try.learning.

2.or.3.commands.initially..Then.carry.out.a.Master.Clear.before.

completely.learning.your.original.remote’s.commands.

g..Carry.out.a.“Mode.Clear”.before.learning.a.Mode.to.make.sure.there.

are.no.previously.learned.commands.for.that.Mode.

h. Place.the.original.remote.end-to-end.with.the.Learning.Remote.so.

the.IR.transmitters.on.both.remotes.are.directly.in.line.with.each.

other..You.may.need.to.adjust.the.height.of.either.remote.to.achieve.

this..

i. Keep.the.distance.between.the.two.remotes.to.approximately.1.inch.

and.do.not.move.or.change.the.distance.between.the.two.remotes.

until.you.have.learned.all.the.required.buttons.for.that.Mode.

j. Avoid.learning.your.original.remote.Volume/Mute.buttons.unless.

you.are.sure.these.operate.the.same.device.e.g..some.original.DVD.

remotes.include.TV.Volume/Mute.button.control.and.can.be.two.

different.types.of.code.

k. Avoid.learning.your.original.remote.VCR.or.DVD.buttons.unless.

you.are.sure.these.operate.the.same.device.e.g..some.original.TV.

remotes.include.VCR.or.DVD.button.control.and.can.be.two.different.

types.of.code.

l..Learning.a.button.can.take.up.to.3.seconds..Do.not.release.the.button.

being.Learned.until.SUCCESS.or.LEARN.ERROR.has.been.displayed.

16

Tips On Learning, cont.

Tips On Learning, cont.

m. If.learning.the.first.or.second.buttons.for.a.Mode.results.in.

continuous.errors.then.try.the.following: i... End.the.Learn.session.by.pressing.the.

EXIT button.

ii...Clear.out.the.learned.commands.for.that.Mode.

iii...Check.the.IR.transmitters.are.correctly.aligned.between.the.two.

remotes.

iv...Adjust.the.distance.between.the.two.remotes.to.be.closer.(e.g..

half.an.inch).or.a.further.away.(e.g..2.inches).from.each.other.

v...Try.learning.the.original.remote.for.that.Mode.again.

If.problems.reoccur.with.the.same.button.check.the.original.remote.

button.being.learned.–.does.it.transmit?.Does.it.operate.the.target.

device?.Try.learning.that.button.under.a.different clear.Mode..If.it.learns.

okay.then.it.is.likely.to.be.a.different.code.type.from.the.others.and.

cannot.be.learned.under.the.same.Mode.

Learning Notes

1.. You.cannot.learn.under.the.Setup.button.

2.. All.learned.commands.for.a.Mode.are.deleted.if.the.same.or.a.new.

4-digit.code.is.entered.for.that.Mode.by.any.Code.Entry.or.Code.

Search.

3.. The.Backlighting.is.turned.off.for.Learning.

17

Learning Commands




SETUP.button.

2.. Press. the. down. navigation. button. repeatedly. until. LEARN. SETUP. is.


OK.

3..MODE.LEARN.is.displayed..Press.and.release.

OK.

4..MODE.KEY?.is.displayed..Press.and.release.the.desired.Mode.button.


5..LEARN.KEY?.is.displayed..Press.and.release.the.key.on.the.24999.remote.

that.you.want.to.be.taught.a.code,.e.g..

POWER.

6..LEARNING.is.displayed..Pointing.the.remotes.as.shown.below,.press.

and.hold.the.original.remote.key.(e.g..

POWER).until.the.SUCCESS.or.

LEARN.ERROR.is.displayed.(see.Tips.on.Learning,.page.19).followed.by.

LEARN.MORE?.(this.process.can.take.up.to.2.or.3.seconds.to.complete)..

Release.the.original.remote.button.

7..LEARN.MORE?.is.still.displayed..To.learn.more.buttons,.press.and.release.

OK and.repeat.from.step.5..To.exit.at.this.point,.press.and.release.EXIT.

8..PLEASE.WAIT.is.displayed.briefly.and.the.remote.exits.Setup.Mode.and.

returns.to.normal.operation.

Line.up.your.remotes.(that.you’re.learning.from).in.front.of.the.Learning.

remote,.on.a.hard.surface.approx..1.inch.apart.

18

Clearing Commands

To Clear all Learned Commands under a mode

Clearing.learned.commands.is.helpful.if,.for.example,.you.replace.your.

CD.player.with.another.brand.or.model..If.you.had.learned.a.feature.

from.your.old.CD.player’s.original.remote.on.to.this.remote.(such.as.

RANDOM.PLAY),.that.feature.would.no.longer.work.for.your.new.CD.

player..Should.you.wish.to.remove.or.clear.one.or.more.“learned”.

commands,.follow.the.steps.below:




SETUP.button.



OK..MODE.LEARN.is.displayed.

3.. Press.the.down.navigation.button.until.MODE.CLEAR.is.displayed..Press.

and.release.

OK.

4.. MODE.KEY?.is.displayed..Press.and.release.the.desired.Mode.button.



OK.

6.. PLEASE.WAIT.is.briefly.displayed.followed.by.SUCCESS.and.the.remote.

exits.Setup.Mode.and.returns.to.normal.operation.

Master Clear - To Clear all Learned Commands under all modes

(recommended on first time Learning)




SETUP.button.



OK..MODE.LEARN.is.displayed.

3.. Press.the.down.navigation.button.repeatedly.until.ALL.LEARN.CLEAR.

is.displayed..Press.and.release.

OK.


OK.

5.. PLEASE.WAIT.is.briefly.displayed.followed.by.SUCCESS.and.the.remote.

exits.Setup.Mode.and.returns.to.normal.operation.

19

Troubleshooting

Remote does not operate your product.

•.Press.the.mode.button.of.the.product.you.want.to.control.

•.Program.the.remote.with.a.new.code.

•.Install.new.batteries..(You.might.have.to.reprogram.your.remote.after.

installing.new.batteries.)

•.Remote.may.not.be.compatible.with.your.product.

Remote does not operate some features of your product.

•.Program.remote.with.a.new.code.

•.Remote.may.not.be.able.to.operate.all.features.of.your.product.or.

button.names.might.be.different.than.your.product.

Lost Your Codes?

Should.you.lose.your.codes.or.programming.instructions,.you.can.find.

available.on.our.website: www.jascoproducts.com

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or

TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

90 Day Limited Warranty

Jasco.Products.Company.warrants.this.product.to.be.free.from.

manufacturing.defects.for.a.period.of.ninety.days.from.the.original.

date.of.consumer.purchase..This.warranty.is.limited.to.the.repair.or.

replacement.of.this.product.only.and.does.not.extend.to.consequential.

or.incidental.damage.to.other.products.that.may.be.used.with.this.

unit..This.warranty.is.in.lieu.of.all.other.warranties.express.or.implied..

Some.states.do.not.allow.limitations.on.how.long.an.implied.warranty.

lasts.or.permit.the.exclusion.or.limitation.of.incidental.or.consequential.

damages,.so.the.above.limitations.may.not.apply.to.you..This.warranty.

gives.you.specific.rights,.and.you.may.also.have.other.rights.which.vary.

from.state.to.state..If.unit.should.prove.defective.within.the.warranty.

period,.return.prepaid.with.dated.proof.of.purchase.to:

Jasco.Products.Company

10.E..Memorial.Road

Oklahoma.City,.OK.73114-2205

20

Universal Remote

Instruction Manual

24999

Jasco.Products.Company

10.E..Memorial.Road

Oklahoma.City,.OK.73114-2205

Made.in.China.

.

21

24999-12/10

GE 24999 Universal Remote Instruction manual

Universal Remote

Instruction Manual

Table of Contents

Introduction

Button Functions

Button Functions, cont.

Setup

Setup, cont.

Code Entry

Code Entry, cont.

Setup, cont.

Setup, cont.

Setup, cont.

Setup, cont.

Setup, cont.

Setup, cont.

Code Learning

Tips On Learning, cont.

Learning Commands

Clearing Commands

Troubleshooting

90 Day Limited Warranty

Universal Remote

Instruction Manual

Related manuals

Philips

SRU6080

Philips

SRU4050/37

Medion

8 in 1 Universal Remote Control MD 82663

RCA

RCU1010RF

Medion

Universal Remote Control MD 83388

Medion

Universal Remote Control MD 81302

Philips

SRU3004WM/17

Philips

SRC3036WM/17

Bauhn

UR39677

GE Capital

24959

Authinx

B4S-24110T

EMTEC Electronics

INTUIX H380