GE Monogram B480DX Refrigerator User Manual

ZISW/B480DX

GE Monogram ® 48" Built-In Side-by-Side Refrigerator with Dispenser and

Water Filter

Dimensions and Installation Information (in inches) The Installation Space

36" Models 12"

42" Models 18"

48" Models 20"

*83-1/2" at

Rear

26-7/8" including handle

47"

Case Width 25-3/8

48"

Frame to Frame

*84" From

Floor to

Top Frame

* Shipping height.

The refrigerator can be adjusted to fit into a cutout that is 83-1/2" min. to

84-1/2” max. height.

Note that the top case trim at the front is 1/2" higher and will overlap upper cabinetry or soffit. Use leveling legs and wheels for a maximum 1" height adjustment.

*Finished Width

84-1/2" max

83-1/2" min

Finished

Opening

6"

Electrical

Area 5"

24"

75" From Floor to Bottom of Electrical

Area

5"

Water Supply

5"

3-1/2"

Product Clearances

These refrigerators are equipped with a 2 position door stop.

The factory set 130° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.

130 ° Door Swing 90 ° Door Swing

15" 20"

23-7/8"

Behind

Frame

28-5/8"

4" Min.

to Wall

Allow minimum clearances for freezer door and fresh food door for a full 130° door swing and to allow for pan removal.

4" minimum clearance is required when door swing is adjusted to 90°. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.

Installation Information: Before installing, consult installation instructions packed with product, or online at Monogram.com, for current dimensional data.

3-1/2"

Water and electrical locations

The opening must be prepared with the electrical and water supply located as shown.

The cutout depth must be 24".

696Dia15

The cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot exceed the

24" installation depth shown. The top case trim overlaps the bottom of the soffit.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is required.

An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3prong electrical receptacle recessed into the back wall.

Electrical must be located on rear wall as shown.

Note: GFI (ground fault interrupter) is not recommended.

• Water line can enter the opening through the floor or back wall. The water line should be 1/4" O.D. copper tubing or

GE SmartConnect ™ kit between the cold water line and water connection location, long enough to extend to the front of the refrigerator. Installation of an easily accessible shut off valve in the water line is recommended.

For answers to your Monogram, ® GE Profile at ge.com or call GE Answer Center

800.626.2000.

®

™ or GE ® appliance questions, visit our website

service,

Listed by

Underwriters

Laboratories

As an EnErgy StAr ® partner, gE has determined that this product meets the

EnErgy StAr guidelines for energy efficiency.

Specification Created 3/08 110180

ZISW/B480DX


Water Filter

Dimensions and Installation Information (in inches)

Customization Basics: Framed or Overlay Panels, Custom Handles and Accessory Kits

Trimmed Refrigerators

ZIS420NXSS, ZISW420DXSS, ZISB420DXSS

Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required.

Framed Panels

You may install 1/4"-thick custom panels from your cabinet manufacturer. The decorative panels slide into the factoryinstalled trim. Or, order black, white and stainless steel accessory panels from your Monogram dealer.

Door Handles

The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed. If desired, you may order ZKHSS2 Monogram stainless steel tubular handle kit for overlay panels.

Side Panels

Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.

• Cut a notch in the top front corner as shown to allow clearance for corner keys in the front side trim.

*84"

24"

3/16"

1-7/8"

Framed Panel

Standard supplied handles shown in 1/4" panel position.

Overlay Panels

You may also choose to install custom overlay panels from your cabinet manufacturer. This design provides a seamless appearance which integrates smoothly with surrounding cabinetry.

605Dia6

*3" to 4"

2-9/16"

*Depending on installation height.

3/4" Overlay Panel

.10" Thick Spacer Panel

1/4" Thick Backer Panel

Standard supplied handles shown in 3/4" overlay panel position.

For answers to your Monogram,

800.626.2000.

® GE Profile at ge.com or call GE Answer Center ®


service,

696Dia2

Optional Accessory Kit

ZKHSS2: Tubular Stainless Steel handles designed to fit

3/4" overlay panels.

Accessory Panels

White or black acrylic and stainless steel accessory panels are available from your Monogram supplier. Panels are cut to size and ready to install. These panel kits must be ordered separately.

Models

White

Acrylic

ZISW480D ZPW480D

Black

Acrylic

ZISB480D

Stainless

Steel

ZPS480D

ZPB480D ZPS480D

ZIS480N ZPW480N ZPB480N ZPS480N

Listed by

Underwriters

Laboratories




ZISW/B480DX


Water Filter


3/4" Overlay Panel Dimensions

For a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels.

.250" + .10" + .750" =

1.100" Total Panel Thickness

Door

3/4"

Overlay

Panel

Raised Overlay Panel Design

On Dispenser Models

When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim.

• The middle rail must be wide enough to allow for the dispenser trim to overlap the opening.

• The middle rail must be 1.100" total thickness to accept the dispenser trim.

1/4" Backer Panel

.10" Spacer

3/4" Overlay Panel

1/4"

Backer

Panel

.10"

Spacer

Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.

NOTE: Left-to-right offset is not always equal to top-to-bottom offset.

Overlay Panel

194Dia_58

Spacer Panel

Backer Panel

16-3/4"

Dispenser

Trim

10-5/8"

Wide

Middle

Rail is

Required

Side View

A

Grille Panel B

194Dia_65

Dispenser

Cutout

F

G C

Dispenser Cutout

48" Side-by-Side (in inches)

A C D E

1/4" Backer Panel 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16

.10" Spacer Panel 45 8-5/8 67 17-1/4 25-1/4

3/4" Spacer Panel 46-1/8 9-3/4 68-5/8 18-13/16 26-13/16

*Dispenser Cutout Position (in inches)

48" Models

F G

17-15/16 5-1/4

Freezer

Panel

Fresh

Food

15-3/8"

D E 9-5/8"

For answers to your Monogram,

194Dia_64

® GE Profile at ge.com or call GE Answer Center

800.626.2000.

®


service,

194Dia_63

* Cut the dispenser opening after the backer, spacer and overlay panels have been assembled.

Important Note: Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer door panel – 53 lbs.

• Grille panel – 18 lbs.

Listed by

Underwriters

Laboratories




ZISW/B480DX


Water Filter


1/4" Framed Panel

Dimensions

If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door and grille.

Door

If the custom panel is less than 1/4" thick, and it fits loosely in the door frame, it can be backed up with a piece of filler material or foam tape to improve the fit.

Important Note:

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer door panel – 53 lbs.

• Grille panel – 18 lbs.

194Dia_59

45-7/8"

5/16"

Trim

Reveal

1/4"

Panel

Dispenser Models

These refrigerators are supplied with two dispenser trims, one for framed panels and one for overlay panels.

1/4" Framed Panel

The framed panel must be 1/4" nominal thickness to fit the dispenser trim.

• The dispenser trim fits over the custom panel and snaps into the freezer door.

• If the panel is less than 0.250" thick, a noticeable gap may be created around the dispenser trim. Foam tape may be applied on the door to improve the fit.

• If the panel is more than 0.250" thick, the dispenser trim cannot be secured to the door.

1/4"

Framed

Panel

FREEZER DOOR

Ice / Water Dispenser

0.250"

Thick

Grille Panel 9-1/2"

Dispenser Cutout

17-13/16"

Dispenser

Cutout

1/4" Dispenser Trim

3/4" Overlay Panels

The overlay dispenser trim is designed to fit a total panel thickness of 1.100".

9-5/8"

15-3/8"

5-1/8"

Freezer

Panel

18-9/16"

Fresh Food

Panel

26-9/16"

68-3/8"

• If the panel is more than 1.100" thick, the dispenser trim cannot be secured to the door.

• The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness.

• Alternative panel construction methods such as securing a

3/4" panel to a 1/4" backer panel cannot be used. Another method, routing a 3/4"-thick panel on all sides, cannot be used. These methods will not result in the required 1.100" panel thickness.

• When a raised panel design is to be used, a custom middle rail is required.

194Dia_63

194Dia64

1/4" Backer Panel

.10" Spacer

Panel

FREEZER DOOR 1.100"

Total

Thickness

Ice / Water Dispenser


800.626.2000.

®


service,

3/4" Overlay

Panel

3/4" Overlay Dispenser Trim

Listed by

Underwriters

696Dia4




ZISW/B480DX


Water Filter


Refrigerator

23-7/8" From

Rear of

Refrigerator

Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips.

Case

Trim

1/2"

3/4"

1"

1-3/4"

2"

1-1/2"

2-3/4"

3"

2-1/2"

Use this page to determine door swing interaction with adjacent cabinets or countertops.

Top View

130° Door Swing

(Factory setting)

Scale 1:1

1/4" 1-1/4" 2-1/4"

1/4"

1/2"

3/4"

1"

IMPORTANT NOTE –

FOR DISPENSER MODELS

Dispenser models are supplied with two dispenser trims, one to fit framed panels and one for overlay panels. Dispenser trim fit to the custom panel depends on correct

panel thickness. Framed panels must be 1/4" nominal. Overlay panels should be constructed as shown to accomplish a total 1.100" thickness.

Door

1/4"

1/2"

3/4"

1"

1-1/4"

3/4" Overlay

Panel

(Nominal Size)


800.626.2000.

®


service,

Listed by

Underwriters

Laboratories




ZISW/B480DX


Water Filter


Refrigerator

Case Trim

23-7/8"

From Rear of

Refrigerator Advance Planning for Built-In Custom

Side-by-Side Refrigerators

Use this page to determine door swing interaction with adjacent cabinets or countertops.

Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing.

The opening must allow for filler strips.

1/4"

1/2"

3/4"

1"

1-1/4"

1-1/2"

Top View

90° Door Swing

(Optional setting)

Scale 1:1

IMPORTANT NOTE –

FOR DISPENSER MODELS

Dispenser models are supplied with two dispenser trims, one to fit framed panels and one for overlay panels. Dispenser trim fit to the custom panel depends on correct panel

thickness. Framed panels must be 1/4" nominal.

Overlay panels should be constructed as shown to accomplish a total 1.100" thickness.

Door

1/4"

1/2"

3/4"

1"

1-1/4"

3/4" Overlay

Panel

(Nominal Size)


800.626.2000.

®


service,

Listed by

Underwriters

Laboratories




ZISW/B480DX


Water Filter

Features and Benefits

• Halogen Light Columns - Located in the freezer and fresh food compartments, extend the full length of the interior compartments providing brilliant, all-level illumination

• LED Lighting - Located at the top of the fresh food compartment, and inside the high-humidity and climatecontrol drawers, illuminates contents without compromising space

• Advanced Temperature Management System with Multi-Shelf

Air Tower - Provides even distribution of air throughout the refrigerator

• Climate-Control Drawer - Allows you to express-chill beverages, express-thaw meats and select specific temperatures for perishable foods

• Dispenser with Proximity Sensor - Designed to accommodate glassware of all sizes, from pitchers to tumblers; control graphics light up as you approach and automatically switch off when you walk away

• Humidity-Controlled Vegetable Drawer - Helps preserve the freshness of foods

• Gallon-Size Door Bin - Holds milk containers, two-liter bottles and pitchers

• Adjustable Spillproof Glass Shelves - Easily accommodate party trays and platters

• Drop-Down Shelf - Provides additional space for a casserole dish or pizza box

• Adjustable Deli Drawer on Full-Extension Slides - Keeps meats, cheeses and other everyday foods within easy reach

• Dairy Bin with Center Divider - Has a unique magnetic seal that locks in freshness

• Model ZISW480DX – White dispenser

• Model ZISB428DX – Black dispenser (shown)

ZISB480DR


800.626.2000.

®


service,




GE Monogram B480DX Refrigerator User Manual

Top View

130° Door Swing

(Factory setting)

Scale 1:1

Top View

90° Door Swing

(Optional setting)

Scale 1:1

Features and Benefits

Related manuals

GE Monogram

ZISW/B480DX

GE

ZISW480DX

Monogram

ZISP420DHSS

GE Monogram

ZISP480DHSS

GE

PSB48YPHSV

GE

ZISW420DX

GE Monogram

Side by Side Refrigerators

Kleenmaid

ZSGS420IBS

GE

PSB42YPHSV

GE

ZISW360DX

GE

ZISW360DX