Hitachi 37HLX99 Flat Panel Television Operating Guide

LCD Flat Panel TELEVISION
Operating Guide for 37HLX99
IMPORTANT SAFETY INSTRUCTIONS....................................................................................... 2-3
FIRST TIME USE ....................................................................................................................... 4-22
THE REMOTE CONTROL........................................................................................................ 23-40
ON-SCREEN DISPLAY ............................................................................................................ 41-69
USEFUL INFORMATION.......................................................................................................... 70-78
END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE...........................................79-87
APPENDIXES...........................................................................................................................88-89
INDEX.............................................................................................................................................90
As an Energy Star® Partner,
Hitachi, Ltd. has determined
that this product meets the
Energy Star® guidelines for
energy efficiency.
Important Safety Instructions
SAFETY POINTS YOU SHOULD KNOW ABOUT
YOUR HITACHI LCD TELEVISION
Our reputation has been built on the quality,
performance, and ease of service of HITACHI LCD
televisions.
Safety is also foremost in our minds in the design of
these units. To help you operate these products
properly, this section illustrates safety tips which will be
of benefit to you. Please read it carefully and apply the
knowledge you obtain from it to the proper operation of
your HITACHI LCD television.
Please fill out your warranty card and mail it to
HITACHI. This will enable HITACHI to notify you
promptly in the improbable event that a safety problem
should be discovered in your product model.
Follow all warnings and instructions marked on
this LCD television.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended
to alert the user to the presence of
uninsulated “dangerous voltage” within the
product’s enclosure that may be of a sufficient
magnitude to constitute a risk of electric shock to a
person.
The exclamation point within an equilateral
triangle, is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
READ BEFORE OPERATING EQUIPMENT
2
Follow all warnings and instructions marked on this
LCD television.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11. Only use the attachments/accessories specified by
the manufacturer.
12.
Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
15.Televisions are designed to comply with the
recommended safety standards for tilt and stability.
Do not apply excessive pulling force to the front, or
top, of the cabinet which could cause the product
to overturn resulting in product damage and/or
personal injury.
16. Follow instructions for wall, shelf or ceiling
mounting as recommended by the manufacturer.
17. An outdoor antenna should not be located in the
vicinity of overhead power lines or other electrical
circuits.
18. If an outside antenna is connected to the receiver
be sure the antenna system is grounded so as to
provide some protection against voltage surges and
built up static charges. Section 810 of the National
Electric Code, ANSI/NFPA No. 70-1984, provides
information with respect to proper grounding for the
mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of
grounding connectors, location of antennadischarge unit, connection to grounding electrodes
and requirements for the grounding electrode.
NEC National Electric Code
Note to the CATV system installer: This reminder is
provided to call the CATV system installer’s attention to
Article 820-44 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding
system of the building, as close to the point of cable
entry as practical.
Important Safety Instructions
Power source
This LCD television is designed to operate on 120
volts 60 Hz, AC current. Insert the power cord into a
120 volt 60 Hz outlet. The power cord is used as the
disconnect device and shall remain readily operable.
Public viewing of copyrighted material
Public viewing of programs broadcast by TV stations
and cable companies, as well as programs from other
sources, may require prior authorization from the
broadcaster or owner of the video program material.
To prevent electric shock, do not use the LCD
television’s (polarized) plug with an extension cord,
receptacle, or other outlet unless the blades and
ground terminal can be fully inserted to prevent blade
exposure.
This product incorporates copyright protection
technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision Corporation, and is intended for home and
other limited consumer uses only unless otherwise
authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
Never connect the LCD television to 50 Hz, direct
current, or anything other than the specified voltage.
Caution
Never remove the back cover of the LCD
television as this can expose you to
very high voltages and other hazards. If
the television does not operate properly,
unplug the LCD television and call your authorized
dealer or service center.
Note
This digital television is capable of receiving analog
basic, digital basic and digital premium cable television
programming by direct connection to a cable system
providing such programming. A CableCARD provided
by your cable operator is required to view encrypted
digital programming. Certain advanced and interactive
digital cable services such as video-on-demand, a cable
operator’s enhanced program guide and data-enhanced
television services may require the use of a set-top box.
For more information call your local cable company.
Caution
Adjust only those controls that are covered in the
instructions, as improper changes or modifications not
expressly approved by HITACHI could void the user’s
warranty.
Note
• There are no user serviceable parts inside the
LCD television.
• Model and serial numbers are indicated on back side
and right side of the LCD television (page 78).
Warning
• To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
• The LCD television should not be exposed to
dripping or splashing and objects filled with liquids,
such as vases, should not be placed on the
television.
• This apparatus shall be connected to a mains
socket outlet with a protective earthing connection.
Hg
Lead/Mercury Notice
This product contains lead and a lamp that contains
mercury. Dispose of this product and its lamp in
accordance with applicable environmental laws. For
lamp recycling and disposal information, go to
For product recycling and
www.lamprecycle.org.
disposal information contact your local government
agency or www.eRecycle.org (in California), the
Electronic Industries Alliance at www.eiae.org (in the
US) or the Electronic Product Stewardship Canada at
www.epsc.ca (in Canada).
FOR MORE INFORMATION, CALL 1-800-HITACHI.
3
Accessories
Check to make sure you have the following accessories before disposing of the packing material.
First time use
쐃 Remote Control
쐋 Power Cord
쐇 Two “AA” size,
1.5V batteries
쐂
Power Swivel Cable
쐏 Table Top Stand
+
-
/
쐄 2 IR Blaster Cables
For U.S. models:
For optional accessories, please access our web site at:
www.hitachi.us/tv
CAUTION:
쐆 1 Ferrite Core
(see page 14)
Note: Please visit our
website for optional
accessories.
1. Ceiling mounting is not recommended. Mounting the panel on the ceiling does not
provide adequate ventilation for the electronics or proper support for the front glass
panel. This LCD television product is designed for a maximum tilting angle of 45
degrees from vertical.
2. This stand for use only with Hitachi 37HLX99. Use with other
apparatus is capable of resulting in instability causing possible injury.
쐃 Remote Control Unit CLU-3861WL
(Part No. HL02069).
쐇 Two “AA” size, 1.5V batteries (P# FQ00021).
쐄 Two IR Blaster cables (P# EY01641).
쐂 Power Swivel Cable (P# EW08432).
쐆 1 Ferrite Core (P#2169513).
쐋 Power Cord (P# EV01841).
쐏 Table Top Stand (P# QJ02673 ).
REMOTE CONTROL BATTERY INSTALLATION
AND REPLACEMENT
BOTTOM VIEW
(Remote Control)
1.
Open the battery cover of the remote control by
pushing down and sliding the back cover off.
2. Insert two new “AA” size batteries for the
remote control.
When replacing old batteries, push them
Press down and slide back to remove.
towards the springs and lift them out.
3. Match the batteries to the (+) and (-) marks in the battery compartment.
4. Replace the cover.
CAUTION: Do not insert batteries with the ‘+’and ‘-’ polarities reversed as this may cause the
batteries to swell or rupture resulting in leakage.
4
How To Set Up Your New Hitachi LCD Television
To take measures to prevent the LCD Television from tipping over and prevent possible injury
it is important to mount the unit in a stable and flat surface.
Wire
ANTENNA
Unless your LCD Television is connected to a cable
TV system or to a centralized antenna system, a good
outdoor color TV antenna is recommended for best
performance. However, if you are located in an
exceptionally good signal area that is free from
interference and multiple image ghosts,
an indoor antenna may be sufficient.
First time use
Securing to a table-top
1. Using wood screws (two) fasten the set to the
clamping screw holes on the rear of the LCD
TV stand as shown below.
2. Using commercially available wood screws, secure
the set firmly in position.
LOCATION
Wood screw
two places
Securing to a Wall
1.Keep the LCD television 4 inches away from the
wall except when mounted using the wall mount
bracket.
2. Secure the television to the wall as shown.
A
B
A
37"
(a) Power Swivel
NOT USED
B
4 in.
12 in.
10 cm
30 cm
(b) Power Swivel
USED
Select an area where sunlight or bright indoor
illumination will not fall directly on the picture screen.
Also, be sure that the location selected allows a free
flow of air to and from the perforated back cover of the
set. In order to prevent an internal temperature
increase, maintain a space of 10 cm (4 inches) from the
sides/back of the Television, and 30 cm (12 inches)
from the top of the television to the wall. To avoid
cabinet warping, cabinet color changes, and increased
chance of set failure, do not place the TV where
temperatures can become excessively hot, for
example, in direct sunlight or near a heating appliance,
etc.
30 cm (12 inches)
10 cm (4 inches)
10 cm (4 inches)
* Please adjust the wire length to avoid
touching the wall when turning the TV.
NOTES: 1. Do not block the ventilation holes of the
LCD Television. Blocking the ventilation
holes might cause fire or defect.
2. In case of an abnormal symptom, unplug
the AC cord.
3. If you purchased the wall mount bracket
option, please ask for professional installer.
Do not install by yourself.
4. Install the unit at a proper area where it does
not expose anyone to any danger of hitting
themselves (for example their hands, head
or face, etc.) against the edge of the unit and
cause personal injury.
5. If the Power Swivel feature will not be
used, the LCD television should be
secured to the wall as shown in fig. (a).
6. If the Power Swivel feature will be used,
the LCD television should be secured
to the wall as shown in fig. (b).
Caution when moving the main unit
As this product is heavy, whenever it is moved, two
people are required to transport it safely. Whenever the
unit is moved it should be lifted forward using the top
and base on both sides of the Television for stability.
When moving the Television, lift the handles and the
botttom frame as shown below.
CONNECT POWER SWIVEL CABLE
Connect one end of cable (Arrow mark facing left) to
the swivel slot of the LCD Rear Panel. Connect the
other end (Arrow mark facing front)to the swivel slot of
the Table Top Stand.
TURNING RADIUS
The maximum turning radius is 30˚ (left and right). Do
not place any objects on the path of the monitor when
using the power swivel feature.
C
D
37"
C
D
10.59 in.
13.93 in.
27 cm
36 cm
37”
5
How to set up your new HITACHI LCD Television
SETTING FOR WALL MOUNTING
First time use
STEP (1) :
Please locate the STAND PLATE metal on the back of the TV . This metal is use to hold the TV and the Base ; so it needs
to be remove in order to separate the TV from the Base.
STAND PLATE METAL
STEP (2):
Please remove the 3 screws and the STAND PLATE metal from the TV, then put back only the screw to the back cover.
Now the 4 screws that holds the TV STAND can be remove to separate the TV from the STAND BASE.
4 SCREWS
PLACE BACK
THIS SCREW
3 SCREWS
STAND PLATE METAL
TV STAND BASE
NOTE:
6
Use the specified WALL MOUNT base for the LCD TV depending on the size of your TV.
Please access our web site at: www.hitachi.us/tv for recommended accessories for your tv.
How to set up your new HITACHI LCD Television
VIEWING
The reccomended viewing horizontal and vertical
angles for this LCD TV is 160°.
If the TV’s audio output will be connected to a Hi-Fi
system’s external speakers, the best audio
performance will be obtained by placing the
speakers equidistant from each side of the receiver
cabinet and as close as possible to the height of
the picture screen center. For best stereo
separation, place the external speakers at least
four feet from the side of the TV, place the surround
speakers to the side or behind the viewing area.
Differences in room sizes and acoustical
environments will require some experimentation
with speaker placement for best performance.
BEST
VERTICAL VIEWING
ANGLE
20
3’
0’
5’
10’
15’
R
20’
S
4" Minimum
80
5'
BEST
HORIZONTAL
10'
80
4" Minimum
ANTENNA CONNECTIONS TO REAR JACK
PANEL
First time use
During daylight hours, reflections from outside light
may appear on the screen. If so, drapes or screens
can be used to reduce the reflection or the TV can
be located in a different section of the room.
15'
20'
VIEWING ANGLE
L
S
VHF (75-Ohm) antenna/CATV (Cable TV)
When using a 75-Ohm coaxial cable system, connect CATV coaxial cable to the AIR/CABLE (75-Ohm) terminal. Or if you
have an antenna, connect the coaxial cable to the same AIR/CABLE terminal.
AIR / CABLE
VHF (300-Ohm) antenna/UHF antenna
When using a 300-Ohm twin lead from an outdoor
antenna, connect the VHF or UHF antenna leads to
screws of the VHF or UHFadapter. Plug the adapter
into the antenna terminal on the TV.
To outdoor antenna
To CATV cable
or
AIR / CABLE
When both VHF and UHF antennas are
connected
Attach an optional antenna cable mixer to the TV
antenna terminal, and connect the cables to the
antenna mixer. Consult your dealer or service store
for the antenna mixer.
To outdoor VHF
or UHF antenna
To UHF
antenna
AIR / CABLE
To outdoor antenna
or CATV system
Antenna Mixer
NOTE:
Connecting a 300-Ohm twin lead connector may cause interference. Using a 75-Ohm coaxial
cable is recommended.
7
Hook-up Cables and Connectors
First time use
Most video/audio connections between components can be made with shielded video and audio cables that have
phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be
purchased from most stores that sell audio/video products. Below are illustrations and names of common
connectors. Before purchasing any cables, be sure of the output and input connector types required by the
various components and the length of each cable.
300-Ohm Twin Lead Cable
This outdoor antenna cable must be connected to an
antenna adapter (300-Ohm to 75-Ohm).
A /V Cable
Used on all standard video and audio cables which
connect to inputs and outputs located on the
television’s rear jack panel and side control panel.
“F” Type 75-Ohm Coaxial Antenna
For connecting RF signals (antenna or cable TV) to the
antenna jack on the television.
S-Video (Super Video) Cable
This connector is used on camcorders, VCRs and laserdisc players with an S-Video feature in place of the
standard video cable to produce a high quality picture.
Optical Cable
This cable is used to connect to an audio amplifier with
an Optical Audio In jack. Use this cable for the best
sound quality.
HDMI Cable
This cable is used to connect your external devices
such as Set-Top-Boxes or DVD players equipped with
an HDMI output connection to the TV’s HDMI input.
Stereo Cable (3.8mm plug to 3.5mm plug)
Used on all standard video and audio cable which
connect to inputs and outputs located on the rear jack
panel and side control panel.
USB Cable
This cable is used to connect your digital camera to the
Photo Input in the side of the LCD television.
IR Blaster Cable (Provided)
Connect the IR Blaster to the IR output of your LCD
Television when using other devices. You must place
the IR blaster in front of the corresponding IR window
of your cable box or VCR. This connection allows
your TV to control your cable box or VCR.
Power Swivel Cable (Provided)
This cable is used to connect the swivel stand to the
rear panel of the LCD Television.
8
AUDIO OUT
3.8mm
STEREO
MINI-PLUG
2
RCA TYPE
PLUGS
Quick Reference Remote Control Buttons and Functions
In addition to controlling all of the functions on your HITACHI LCD TV, the new remote control is designed to
operate different types of devices, such as, DVD Players, CBL (Cable Boxes), set-top-boxes, satellite receivers,
and VCRs. The remote control must be programmed to control the chosen device. Please see pages 23-40 for a
complete description of all features and programming of the Remote Control.
First time use
POWER BUTTON
(TV, DVD, CBL, STB, PVR/VCR, AMP/CD)
Turns the selected device on and off.
MODE INDICATOR
Turns on or blinks to show remote control
mode when the SOURCE ACCESS buttons
are pressed.
SOURCE ACCESS BUTTONS
(TV, DVD, CBL, STB, PVR/VCR, AMP/CD)
Changes the mode of the Universal Remote
Control to control the device selected.
ASPECT BUTTON
(TV)
Changes the aspect ratio of the TV.
DAY/NIGHT
(TV)
Toggles picture mode settings between
DAY and NIGHT mode.
MENU BUTTON
(TV, DVD, CBL, STB, PVR/VCR)
Accesses the OSD menu system.
CURSOR PAD/SELECT BUTTON
(TV, DVD, CBL, STB, PVR/VCR)
The Cursor Pad is used as a cursor to navigate
through the OSD and INPUT menu systems.
The Select button is used to Select/Activate
highlighted menu items.
CURSOR UP & DOWN /CH + & CH - BUTTON
(TV, CBL, STB, VCR)
The CH+ or CH- is used to change channels up or down.
The Cursor UP or DOWN to navigate through the OSD
and INPUT menu systems.
INFO BUTTON
(TV, STB, CBL, PVR)
Displays various information on the screen,
such as channel information.
VOLUME WHEEL
(TV, AMP/CD)
Scroll up and down to adjust the audio level of your
TV. Push down on the wheel to mute.
DVD/VCR CONTROL BUTTONS
(DVD, PVR/VCR, AMP/CD)
Controls the functions of your VCR, DVD
and audio devices.
PAUSE BUTTON
(TV,PVR/VCR, DVD, AMP/CD)
Press to show and change the Freeze mode of the TV.
Also used to pause other devices when the remote is in
DVD, PVR/VCR, or AMP/CD mode.
PIP CONTROL BUTTONS
(TV)
Press to show and change the Picture-in-Picture mode.
GUIDE BUTTON
(TV, STB, CBL, PVR)
Accesses the TV Guide On ScreenTM system (see page 49)
of the TV or the program guide of other devices.
EXIT BUTTON
(TV, CBL, STB, PVR/VCR)
Exits out of the OSD, INPUTS or AV NET menu
systems if their menu is displayed.
LAST CHANNEL BUTTON
(TV, CBL, STB, PVR)
Switches between the current and last channel viewed.
INPUTS BUTTON
(TV, AMP)
Accesses the INPUTS menu system.
CHANNEL WHEEL
(TV, CBL, STB, PVR/VCR, AMP/CD)
Scroll up or down to change channel. Push down on
the wheel to access (FAV) Favorite Channel mode.
(Favorite channel is only available for TV mode.)
NUMERIC BUTTONS
(TV, DVD, CBL, STB, PVR/VCR, AMP/CD)
Used to manually enter the TV channel, and used
for numeric entry when navigating through the OSD,
INPUTS .
(-) BUTTON
(TV,STB)
The (-) button is used when the remote is in
Set-Top-Box (STB) mode or when the TV uses
a digital input.
LEGEND
TV – Television
CBL – Cable Box
STB – Set-Top-Box
LIGHT BUTTON
Press to use the back light feature. Can
also be used to change backlight mode.
PVR – Video Recorder/Player
DVD – Digital Video Disc Player
AMP – Audio Amplifier
NOTES: 1. The TV’s remote control sensor is located on the right lower portion of the TV screen. To
control TV functions, please point the remote control directly at the remote control sensor for
best results.
2. VCR precode is included in the PVR mode.
3. CD precode is included in the AMP mode.
4. Pressing the Light button will illuminate the backlight for 8 seconds.
9
First time use
Front/Side Panel Controls
햹
햺
햸
햴
햽
햲
햶
햷
햵
햻
햳
햸
햲
SIDE POWER button
Press this button to turn the LCD Television
ON/OFF. It can also be turned ON/OFF by remote
control. The “MAIN POWER” button must be at
stand-by mode.
햳
MENU/SELECT button
This button allows you to enter the MENU, making
it possible to set TV features to your preference
without using the remote. This button also serves
as the SELECT button when in MENU mode.
햴
SIDE HDMI INPUT (5)
Firmly bind the cables.
Thread the square
hole with the band.
햸
POWER button
Television MAIN POWER button
This power button is for the complete system, and
must be turned ON/OFF manually. It is
recommended to leave the “MAIN POWER” to ON
condition (lights red) for stand-by mode.
Use the side HDMI input for extrenal devices such
as Set-Top-Boxes or DVD players equipped with an
HDMI output connection (see page 15 for reference).
10
햵
INPUT/EXIT button
Press this button to access the INPUT menu.
Press again to exit the MENU mode.
햶
CHANNEL selector
Press these buttons until the desired channel
appears in the top right corner of the TV screen.
These buttons also serve as the cursor down ()
and up () buttons when in MENU mode.
햷
VOLUME level
Press these buttons to adjust the sound level. The
volume level will be displayed on the TV screen.
These buttons also serve as the cursor left () and
right () buttons when in MENU mode.
Hook the band
to the claw.
The Main Power
button is located on
the underside of the
bottom, under the
label “MAIN
POWER”.
NOTE:
When the “MAIN POWER” button is set to
OFF or the TV is unplugged, the clock will
stop and may eventually reset itself.
Front/Side Panel Controls
햹 POWER light indicator
To turn the TV ON, press the main power
switch located on the lower right side of the
TV. A red stand-by indicator lamp located on
the lower right of the front bezel will
illuminate. The LCD TV is now ready for
remote ON/OFF operation.
Off
Off
OFF.
Lights
Red
Off
Off
Blinking
Blue
Lights
Blue
OFF.
(Stand-by)
OFF.
(Turning ON )
Off
Lights
Orange
Off
On
Off
(Power Saving)
Lamp 1
IR Sensor
Operating
When the main power switch is set to Off.
When the main power switch on the TV
is ON.
TV MAIN POWER is ON ; but no picture is shown.
TV MAIN POWER is ON ; picture is shown.
TV MAIN POWER is ON with no signal input
except antenna (no sync. signal).
햺 REMOTE CONTROL sensor
Point your remote at this area when selecting
channels, adjusting volume, etc.
햺 IR OUT sensor
Point your equipment’s remote control at this area.
The IR will pass through the IR Blaster cables
to your equipment.
햻
First time use
Indicating Lamp
Power Status
Lamp 1 Lamp 2
Lamp 2
햽 PHOTO INPUT
Insert USB cable from your Digital Camera, USB
memory or memory card USB drive to view your
digital still pictures (see page 27).
SIDE INPUT JACKS (for INPUT:5)
INPUT 5 provide Y-PBPR jacks for
connecting equipment with this capability, such as
a DVD player or Set Top Box. You may use
composite video signal for this input.
NOTE: 1. Your component outputs may be labeled
Y, B-Y, and R-Y. In this case, connect the
components B-Y output to the TV’s PB
input and the components R-Y output to
the TV’s PR input.
2. Your component outputs may be labeled
Y-CBCR. In this case, connect the component
CB output to the TV’s PB input and the
component CR output to the TV’s PR input.
3. It may be necessary to adjust TINT to
obtain optimum picture quality when using
the Y-PBPR inputs (see page 43).
4. INPUT 3, INPUT 4 and INPUT 5 (Y/VIDEO) can
be used for composite video and component
video input.
NOTES:
1.
2.
Your HITACHI LCD TV will appear to be turned OFF (lights orange) if there is no video input
when INPUT : 1, 2, 3, 4 and 5. Check the Power Light condition to make sure the TV is
turned off or in Stand-by mode (lights red) when not in use.
Remote Control can not turn ON/OFF the “MAIN POWER” of the TV.
11
Rear Panel Connections
햸
햲
First time use
햲 Antenna Input
To switch between Cable and Air input, go to the
Channel Manager option to change the signal
source CABLE or AIR (see page 52).
햾
햺
햹
햶
햳 Audio/Video Inputs 1, 2, 3 and 4
By using the INPUTS button, the CURSOR PAD (
and ), and the SELECT button or CURSOR PAD
of the remote control, you can select each video
source. Use the audio and video inputs to connect
external devices, such as VCRs, camcorders,
laserdisc players, DVD players etc. (if you have
mono sound, insert the audio cable into the left
audio jack).
햴 MONITOR OUT & HI-FI AUDIO OUT
These jacks provide fixed and variable audio and
video signals (CABLE/AIR or INPUTS )
which are used for recording. Use the S-VIDEO
Output for high quality video output. Component
signal to Input 3,4 and 5, and HDMI inputs will not
have monitor output.
햵 Optical Out (Digital Audio)
This jack provides Digital Audio Output for your
audio device that is Dolby® Digital and PCM
compatible, such as an audio amplifier.
NOTE: *Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby
Laboratories.
햶 S-VIDEO Inputs 1 and 2
Inputs 1 and 2 provide S-VIDEO (Super Video)
jacks for connecting equipment with S-VIDEO
output capability.
NOTE: 1. You may use VIDEO or S-VIDEO inputs to
connect to INPUT 1 and 2, but only one of
these inputs may be used at a time.
2. S-VIDEO output may be used for
recording, only when the input is of SVIDEO type.
햷 HDMI 1, 2 & 5 (High Definition Multimedia
Interface)
ABOUT HDMI – HDMI is the
next-generation all digital interface for consumer
electronics. HDMI enables the secure distribution
of uncompressed high-definition video and multichannel audio in a single cable. Because digital
television (DTV) signals remain in digital format,
HDMI assures that pristine high-definition images
retain the highest video quality from the source all
the way to your television screen.
Use the HDMI input for your external devices such
as Set-Top-Boxes or DVD players equipped with an
HDMI output connection.
12
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
햻
햷
햴
햳
햽햵
NOTE: 1. The HDMI input is not intended for use
with personal computers.
2. Only DTV formats such as 1080i, 720p, 480i
and 480p are available for HDMI input.
햸 Component: Y-PBPR Inputs
INPUTS 3 and 4 provide Y-PBPR jacks for
connecting equipment with this capability, such as
a DVD player or Set Top Box. You may use
composite video signal for both inputs.
NOTE: 1. Do not connect composite VIDEO and
S-VIDEO to INPUT 1 or 2 at the same
time. S-VIDEO has priority over VIDEO input.
2. Your component outputs may be labeled
Y, B-Y, and R-Y. In this case, connect the
components B-Y output to the TV’s PB
input and the components R-Y output to
the TV’s PR input.
3. Your component outputs may be labeled
Y-CBCR. In this case, connect the component
CB output to the TV’s PB input and the
component CR output to the TV’s PR input.
4. It may be necessary to adjust TINT to
obtain optimum picture quality when using
the Y-PBPR inputs (see page 43).
5. To ensure no copyright infringement, the
MONITOR OUT output will be abnormal,
when using the Y-PBPR jacks and HDMI
Input.
6. INPUT 3 , 4 and 5 (Y/VIDEO) can be
used for composite video and component
video input.
햹 IR Out / G-Link
This jack provides IR output to your external components
(VCR, Cable box, DVD player, etc.). This connection
will allow you to control the external components with
your LCD Television’s remote control .
(For reference see pages 16).
햺 For FACTORY use only.
Rear Panel Connections
If the CableCARD is properly installed or removed, the
TV will display the following respective screens.
First time use
햻 Upgrade Card
This card slot is for future software upgrades.
Hitachi will notify you if a software upgrade is
required for your TV. In order to receive written
notification, please complete and return your
warranty card.
CableCARD is installed
햽 Power Swivel Connector
Connects to the Power Swivel Table Top Stand.
햾 CableCARD Slot
This slot is for the CableCARD that will be provided
by your local cable operator to gain access to
chosen cable channels. The CableCARD will allow
you to tune digital and high definition cable
channels. Please call your local cable operator if
this service is available before requesting a
CableCARD (also known as Point of Deployment
(POD) module).
1.
2.
Connect a coaxial cable to cable terminal of
the Rear Panel Jacks.
Insert the CableCARD into the slot (Top of card
should be facing towards you as shown below).
Completely insert the card until the back end
aligns with the line as shown.
OR
CableCARD is not installed
After the CableCARD is installed, wait until the second
screen below appears.
Digital Cable
Acquiring Data.
Please wait.
INSERT
In order to start cable service
for this device, please contact
your cable provider
CableCARD(tm): 123-456-789-1
Host: 123-456-789-1
Data: 123-456-789-1
Unit Address: 123-456-789-1
Press EXIT to return
NOTE: 1. A digital cable subscription is required.
2. Do not insert a PCMCIA card into the
CableCARD slot.
Please take note of all information on the screen (you
will provide this information to your cable operator).
Call your cable operator and give them the information
from the card to start your cable service (refer to page 67
for more information).
13
Connecting External Video Sources
The LEFT SIDE panel jacks are provided as a convenience to allow you to easily connect a camcorder , DVD, Video
Game, VCR and a Digital Camera as shown in the following examples:
Left Side Panel
Left Side Panel
First time use
INPUT 5
R
L/MONO
PR
AUDIO
R
PHOTO
INPUT
PB
L/MONO
AUDIO
PR
PHOTO
INPUT
PB
Y / VIDEO
Y / VIDEO
Note : Connection cables will depend
on the external device
specification.
R
OUTPUT
L
PR /C R PB /C B
R
Y
L
OUTPUT
V
COMPONENT
OUTPUT CAPABILITY
DVD , Set Top Box,
Video Game Console.
Video Game
Video Camera
NOTE: 1. Completely insert connection cord plugs when connecting to left side panel jacks. If you do not, the
played back picture may be abnormal.
Left Side Panel
INPUT 5
R
L/MONO
AUDIO
PR
PB
PHOTO
INPUT
Y / VIDEO
Ferrite Core Instructions:
1. Wrap once the USB cable on
the ferrite core near the Photo
Input as shown.
Ferrite
Core
2. Fold and close the ferrite core
while being careful not to pinch
the cable.
USB
Cable
Digital Camera
14
Connecting External Video Sources
The RIGHT SIDE panel jacks are provided as a convenience to allow you to easily connect HDMI or DVI signals
from a DVD, Set Top Box , Video Game as shown in the following examples (When connecting DVI signal it will
need to connect the audio output into the Left Side Input jacks) :
A) Connecting HDMI signal.
First time use
B) Connecting DVI signal.
Right Side Panel
Left Side Panel
Right Side Panel
INPUT 5
R
L/MONO
AUDIO
PR
PB
Y / VIDEO
DVI to HDMI
Cable
Note : Connection cables will depend
on the external device
specification.
DIGITAL OUTPUT
OUTPUT
R
L
Back of
HDTV Set-Top-Box or
DVD Player
HDMI DIGITAL
OUTPUT CAPABILITY
DVD , Set Top Box,
Video Game Console.
DVI DIGITAL
OUTPUT CAPABILITY
DVD , Set Top Box,
Video Game Console.
NOTE: 1. Completely insert connection cord plugs when connecting to side panel jacks. If you do not, the
played back picture may be abnormal.
The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set
Top Box to your LCD TV is dependent on the model and features of each component. Check the
owner’s manual of each component for the location of video and audio inputs and outputs.
The following connection diagrams are offered as suggestions. However, you may need to modify them to
accommodate your particular assortment of components and features. For best performance, video and
audio cables should be made from coaxial shielded wire.
Before Operating External Video Source
Connect an external source to one of the INPUT terminals, then press the INPUTS button to show the
INPUTS menu. Use the CURSOR PAD ( and ) to select the Input of your choice. Then press
the SELECT button or the CURSOR PAD to confirm your choice (see page 26).
Input 5
Photo Input
Air / Cable
Input 1
Input 2
Move
SEL Sel.
15
Rear Panel Connections
Outside Antenna
or
Cable TV coaxial cable
First time use
2-Way signal splitter
VCR #1
DIGITAL
OUTPUT CAPABILITY
OUTPUT
ANT
IN
S-VIDEO V
L
R
DIGITAL OUTPUT
AUDIO OUT
DVI
to
HDMI
Optional
HDMI
to
HDMI
Optional
Y
OUTPUT
PB/CB PR/CR L
HDMI OUTPUT
R
S-VIDEO V
L R
INPUT
DVD Player
VCR #2
S-VIDEO V
L R
OUTPUT
Laserdisc player, VCR,
camcorder, etc.
Y
PB PR L
OUTPUT
HDTV Set-Top Box
(PROVIDED)
CONNECT TO
G-LINK/IR OUT
(PROVIDED)
CONNECT TO
IR OUT
NOTE: Cables are optional, except when specified.
16
R
HDMI DIGITAL
OUTPUT CAPABILITY
Tips on Rear Panel Connections
• S-VIDEO, Y-PB PR, or HDMI connections are provided for high performance laserdisc players, VCRs etc. that
have this feature. Use these connections in place of the standard video connection if your device has this
feature.
First time use
• If your device has only one audio output (mono sound), connect it to the left audio jack on (L/(MONO)) the
Rear Panel.
• Refer to the operating guide of your other electronic equipment for additional information on connecting
your hook-up cables.
• A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line
output (INPUT: 1 in the example on page 16). Refer to your VCR operating guide for more information on
line input-output connections.
• Connect only 1 component (VCR, DVD player, camcorder, etc.) to each input jack.
• COMPONENT: Y-PBPR (Input 3, 4 & 5) connections are provided for high performance components, such as
DVD players and set-top-boxes. Use these connections in place of the standard video connection if your
device has this feature.
• Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y
output to the TV’s PB input and the components R-Y output to the TV’s PR input.
• Your component outputs may be labeled Y-CBCR. In this case, connect the components CB output to the
TV’s PB input and the components CR output to the TV’s PR input.
• It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPR inputs. (See
page 43)
• To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-PBPR, and
HDMI input jacks.
• Input 1 , 2 or 5 can accept HDMI signal.
• S-VIDEO monitor output may be used for recording only when the input is of S-VIDEO type.
• When using a HDMI input from a Set-Top-Box, it is recommended to use a 1080i or 720p input signal.
INSTALLATION RECOMMENDATION:
1. Video signals fed through a VCR may be affected by copyright protection systems and the picture will be
distorted on the television.
2. Connecting the television directly to the Audio /Video output of a Set-Top-Box will assure a more normal
picture.
17
Connecting External Video Sources
CONNECTING A VIDEO AND STEREO AUDIO
SOURCE TO INPUT1 – INPUT5
First time use
1. Connect the cable from the VIDEO OUT of the
VCR or the laserdisc player to the INPUT
(VIDEO) jack, as shown on the Rear Panel to the
right.
2. Connect the cable from the AUDIO OUT R of the
VCR or the laserdisc player to the INPUT
(AUDIO/R) jack.
3. Connect the cable from the AUDIO OUT L of the
VCR or the laserdisc player to the INPUT
(AUDIO/L) jack.
4. Press the INPUTS button, then select INPUT 2
from the INPUTS menu to view the program
from the VCR or laserdisc player.
Back of
VCR
5. Select CABLE or AIR from the INPUTS menu to
return to the last channel tuned.
OUTPUT
VCR
NOTE: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and
sound that is played back will be abnormal if the connection is loose.
2. A single VCR can be used for VCR #1 and VCR #2 (see page 16) but note that a VCR cannot record
its own video or line output. Refer to your VCR operating guide for more information on line inputoutput connections.
3. When INPUT 3 , 4 or 5 are used, it is necessary to connect the video output of the device to the
Y/VIDEO input jack of the TV (For INPUT 5 please see page 14 for reference).
CONNECTING AN S-VIDEO AND STEREO AUDIO
SOURCE TO INPUT 1, 2
CABLE
or
Air signal
1. Connect the cable from the S-VIDEO OUT of
the S-VHS VCR or the laserdisc player to the
INPUT (S-VIDEO) jack, as shown on the Rear
Panel to the right.
2. Connect the cable from the AUDIO OUT R of
the VCR or the laserdisc player to the INPUT
(AUDIO/R) jack.
3. Connect the cable from the AUDIO OUT L of
the VCR or the laserdisc player to the INPUT
(AUDIO/L) jack.
4. Press the INPUTS button, then select INPUT 1
from the INPUTS menu to view the program
from the VCR or laserdisc player.
5. Select CABLE or AIR from the INPUTS menu to
return to the last channel tuned.
Back of VCR or
Laserdisc Player
R
L
V S-VIDEO
OUTPUT
VCR or Laserdisc Player
NOTE: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and
sound that is played back will be abnormal if the connection is loose.
2. A single VCR can be used for VCR #1 and VCR #2 (see page 16), but note that a VCR cannot record
its own video or line output. Refer to your VCR operating guide for more information on line inputoutput connections.
18
Connecting External Video Sources
CONNECTING A COMPONENT SOURCE WITH
HDMI OR DVI CAPABILITY TO INPUT 1, 2 OR 5
2. With DVI output, connect the cable from the
AUDIO OUT R of the HDTV set top box or DVD
player to the INPUT (AUDIO/R) jack as shown on
the Rear Panel below.
3. With DVI output, connect the cable from the
AUDIO OUT L of the HDTV set top box or DVD
player to the INPUT (AUDIO/L) jack as shown
on the Rear Panel below.
4. Press the INPUTS button, then select INPUTS 1,
2 or 5 to view the program from the HDTV set
top box or DVD player.
5. Select CABLE or AIR from the INPUTS menu to
return to the last channel viewed.
First time use
1. Connect the HDMI or DVI to HDMI connection
cable from the output of the HDTV set top box
or DVD player to the HDMI
input as shown on the Rear panel below.
NOTE: 1. Completely insert the connection cord
plugs when connecting to rear panel jacks.
The picture and sound that is played back
will be abnormal if the connection is loose.
2. The HDMI input on INPUT 1 , 2 and 5
contains the copy protection system called
High-bandwidth Digital Content Protection
(HDCP). HDCP is a cryptographic system
that encrypts video signals when using
HDMI connections to prevent illegal
copying of video contents.
3. HDMI is not a “NETWORK” technology. It
establishes a one-way point-to-point
connection for delivery of uncompressed
video to a display.
4. The connected digital output device
controls the HDMI interface so proper setup of device user settings determines final
video appearance.
5. When using a DVI to HDMI cable, connect
the Audio Out L and R cables at the same
INPUT (1 , 2 or 5) as your HDMI INPUT(1 , 2 or 5).
(For INPUT 5 please see page 15 for reference).
HDMI input
CABLE
or
Air signal
HDMI
Cable
or
DIGITAL OUTPUT
Back of
HDTV Set-Top-Box or
DVD Player
HDTV Set-Top-Box or
DVD Player
DVI to HDMI Input
CABLE
or
Air signal
DVI to HDMI
Cable
PB
PR
or
DIGITAL OUTPUT
L
R
OUTPUT
Back of
HDTV Set-Top-Box or
DVD Player
or
HDTV Set-Top-Box or
DVD Player
19
Connecting External Audio/Video Devices
First time use
CONNECTING A COMPONENT AND STEREO
AUDIO SOURCE TO INPUT 3 , 4 or 5 :Y-PBPR.
1.
Connect the cable from the Y OUT of the
Laserdisc/DVD player or HDTV set top box to
the INPUT (Y) jack, as shown on the Rear
panel below.
2.
Connect the cable from the PB/CB OUT or BY OUT of the Laserdisc/DVD player or HDTV
set top box to the INPUT (PB) jack.
3.
Connect the cable from the PR/CR OUT or RY OUT of the Laserdisc/DVD player or HDTV
set top box to the INPUT (PR) jack.
4.
Connect the cable from the AUDIO OUT R of
the Laserdisc/DVD player or HDTV set top box
to the INPUT (AUDIO/R) jack.
5.
Connect the cable from the AUDIO OUT L of
the Laserdisc/DVD player or HDTV set top box
to the INPUT (AUDIO/L) jack.
6.
Press the INPUTS button, then select INPUT 4
from the INPUTS menu to view the program
from the Laserdisc/DVD player or HDTV set
top box.
7.
Select CABLE or AIR to return to the last
channel tuned.
NOTE: 1. Completely insert the connection cord
plugs when connecting to rear panel jacks.
The picture and sound that is played back
will be abnormal if the connection is loose.
2. See page 17 for tips on REAR PANEL
CONNECTIONS.
(For INPUT 5 please see page 14 for reference).
CABLE
or
Air signal
L
R
OUTPUT
Y
PB
OR
VIDEO
PR/CR PB/CB Y
AUDIO
L
HDTV Set-Top Box
DVD Player
20
Back of
DVD Player
OUTPUT
PR
R
Connecting External Audio/Video Devices
CONNECTING A VIDEO AND MONAURAL AUDIO
SOURCE TO INPUT 1 ~ INPUT 5
CABLE
or
Air signal
First time use
1. Connect the cable from the VIDEO OUT of the
VCR or the laserdisc player to the INPUT
(VIDEO) jack, as shown on the Rear Panel on
the right.
2. Connect the cable from the AUDIO OUT of the
VCR or the laserdisc player to the INPUT
(MONO)/L(AUDIO) jack.
3. Press the INPUTS button, then select INPUT 2
from the INPUTS menu to view the program
from the VCR or the laserdisc player.
4. Select CABLE or AIR from the INPUTS menu to
return to the previous channel.
Back of
VCR
AUDIO OUT
CONNECTING OPTICAL OUT TO AN EXTERNAL AUDIO AMPLIFIER
To monitor the audio level of the LCD TV to an
external audio amplifier, connect the system as
shown on the right. The “OPTICALOUT” from the
Rear Panel is a fixed output. The Volume of the
amplifier is controlled by the amplifier, not by the
LCD Television. The OPTICAL OUT terminal
outputs all audio sources with Optical IN capability.
VIDEO OUT
OUTPUT
(For INPUT 5 please see page 14 for reference).
VCR
CABLE
or
Air signal
1. Connect an optical cable from the Optical out to
the Optical input of a separate Stereo System
Amplifier as shown on the Rear Panel on the
right.
Stereo System Amplifier
OPTICAL
IN
Stereo System Amplifier
or DVD Player
CONNECTING MONITOR OUT
The MONITOR OUT terminal outputs video and
audio of CABLE/AIR and INPUTS 1, 2, 3, 4 and 5. It
does not output component and HDMI video.
1.
CABLE
or
Air signal
Connecting S-Video:
Connect the cable from the S-VIDEO OUT of
the Rear Panel to the INPUT (S-VIDEO) jack,
of the VCR .
Optional
Connecting Video:
Connect the cable from the VIDEO INPUT of
the VCR to the VIDEO out jack on the TV
Rear Panel.
2.
3.
Connect the cable from the AUDIO IN R of the
VCR to the OUTPUT (AUDIO/R) jack on the
TV Rear Panel.
Connect the cable from the AUDIO IN L of the
VCR to the OUTPUT (AUDIO/L) jack on the
TV Rear Panel.
R
L
V
INPUT
S-VIDEO
VCR or other external
components
NOTE: When making video connections, connect S-Video only or Video only. If both are connected, SVideo takes priority.
21
First time use
Connecting External Video Sources
Your HITACHI LCD Television is equipped with a G-LINK feature. This connection is necessary for the TV
Guide On ScreenTM system to work with your cable box to receive program listings and to enable VCR
recording features. Once you setup the G-LINK (IR Blaster) connector, then you can use your HITACHI
LCD TV Remote Control and the TV Guide On Screen system to control your cable box and VCR
recording features.
The LCD Television Rear Panel has IR OUT/G-LINK terminals. One IR Blaster cable can connect up to
2 external Audio/Video components. Please see the following example of a G-LINK setup between your
HITACHI LCD Television and external Audio/Video equipment (VCR and Cable box).
CONNECTING THE CABLE BOX/VCR TO G-LINK FOR TV GUIDE ON SCREENTM SYSTEM
1.
Connect your external Audio/Video components to the Rear Panel shown below.
2.
Connect the IR Blaster cable to the IR OUT/G-LINK output terminal of the Rear Panel.
3.
Place the IR Blaster in front of the infrared sensor of the external components you want to control.
Y
V
L
OUTPUT
R
Infrared
Sensor
Infrared
Sensor
VCR
IR
Blaster
4.
To access the TV Guide On-ScreenTM system,
press the MENU button.
Video
Audio
TV Guide On Screen
Channel Manager
5.
Use the CURSOR PAD or channel scroll down
to highlight TV GUIDE ON SCREEN.
Locks
Timers
Setup
Power Swivel
Move
6.
Press the SELECT or CURSOR PAD button to
select.
7.
Follow the Setup procedure on pages 49-51.
NOTE:
22
G-LINK connections are available on both IR OUT terminals.
OUTPUT
PB/CB PR/CR R
SEL Select
Cable Box
L
The Remote Control
In addition to controlling all the functions on your
HITACHI LCD TV, the new remote control is
designed to operate different types of VCRs, CATV
(Cable TV) converters, set-top-box, satellite
receiver, DVD players, and other audio/video
equipment with one touch. Basic operation keys
are grouped together in one area.
To operate your LCD TV, point the remote
control at the remote sensor of the television and
select the TV by pressing the or button of the
Source Access on the remote. The TV mode
indicator will blink, indicating that the remote will
now control your television.
To operate your PVR (Personal Video Recorder),
point the remote at the remote sensor of the PVR
and select PVR by pressing the or button of
the Source Access on the remote. The PVR mode
indicator will blink, indicating that the remote will
now control your PVR (see page 36 for instruction
on how to program the remote to control your
PVR).
There are two modes of illuminating the Remote Control buttons.
They are the Automatic and Manual modes.
AUTOMATIC MODE (Optional mode)
In Automatic mode, if any button is pressed (including the
LIGHT button), the illumination will last for 4 seconds.
The Remote Control
To operate your VCR, point the remote at the
remote sensor of the VCR and select PVR by
pressing the or button of the Source Access
on the remote. The PVR mode indicator will blink,
indicating that the remote will now control your
VCR (see page 36 for instructions on how to
program the remote to control your VCR).
To operate additional audio equipment, point the
remote at the remote sensor of the component you
wish to control and select AMP by pressing the or button of the Source Access on the remote.
The AMP mode indicator will blink, indicating that
the remote will now control your audio equipment
(see page 37 for instructions on how to program
the remote to control additional Audio/Video
equipment).
MANUAL MODE (Default mode)
In Manual mode, the illumination will only work when the
LIGHT button is pressed. When the LIGHT button is pressed,
the illumination will last for 8 seconds. During the illumination, if the LIGHT button is pressed, the illumination will turn
off.
CHANGING LIGHTING MODES (Automatic to
Manual/Manual to Automatic)
1.
Place the Remote Control in TV Mode by using the
SOURCE ACCESS and buttons. The TV mode
indicator will blink 3 times to confirm the remote control
mode.
2.
Press and hold the LIGHT button for 10 seconds. After
releasing the LIGHT button, the TV mode indicator will
blink 3 times to confirm the mode switch.
NOTE:
When you press any remote control button,
the buttons will light up. The illumination will
last a few seconds during this time. The
buttons will appear illuminated if the room
is dark.
To operate your cable box, point the remote at the
remote sensor of the cable box and select the
CABLE (CBL) by pressing the or button of the
Source Access on the remote. The CBL mode
indicator will blink, indicating that the remote will
now control your cable box (see page 33 for
instructions on how to program the remote to
control your cable box).
To operate your set-top-box or satellite receiver
point the remote at the remote sensor of the settop-box and select the SET-TOP-BOX (STB) by
pressing the or button of the Source Access
on the remote. If you have a satellite receiver, use
this button to program your satellite receiver. The
STB mode indicator will blink, indicating that the
remote will now control your set-top-box (see
page 34 for instructions on how to program the
remote to control your set-top-box).
A/V NET
+
-
/
To operate your DVD player, point the remote at
the remote sensor of the DVD player and select
DVD by pressing the or button of the Source
Access on the remote. The DVD mode indicator
will blink, indicating that the remote will now
control your DVD Player (see page 35 for
instruction on how to program the remote to
control your DVD
player).
23
How to Use the Remote to Control Your TV
햲 POWER button
Press this button to turn the TV set on or off when
the remote is in TV mode. (See page 23 for
instructions on how to set the remote control to TV
mode.)
햲
햳
햵
햴
햳 MODE Indicator
Turns on or blinks to show remote control mode.
햴 SOURCE ACCESS ( or ) buttons
Press these buttons to select remote control mode.
햶
햹
The Remote Control
햷
햸
햿
햽
햺
+
햾
헃
-
헁
햻
햵 SOURCE ACCESS (ENT) button
Hold down this button while entering your device
code to program the remote (see pages 33-38).
You can also use this button in an optional Input
access feature (see page 38).
햶 PAUSE button
Press the PAUSE button to freeze the picture.
Press the EXIT button to return the picture to
motion. Press the PAUSEbutton repeatedly to
cycle through the three different freeze modes
(see page 32).
헀
/
헂
헃
헃
헄
Freeze
헅
Freeze
Freeze
Freeze
Freeze
24
How to Use the Remote to Control Your TV
햷 ASPECT button
Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal format
received, the picture format ratio allows you to adjust the images through the following options.
4:3 STANDARD
Use this aspect mode to display conventional (4:3)
images. Side panels (gray areas) are placed to the
left and right of the image to preserve the original
aspect ratio of the source.
• Antenna-Analog Channel
• S-Video/Video Input
(Auto Aspect: Off)
• HDMI-480i/480p Input
(Auto Aspect: Off)
• Component-480i/480p
Input (Auto Aspect: Off)
16:9 STANDARD 1
Use this aspect mode to display 16:9 sources like
HDTV and DVD’s preserving the original 16:9
aspect ratio showing 95% of the size.
16:9 STANDARD 2
Use this aspect mode to display 16:9 sources like
HDTV and DVD’s preserving the original 16:9
aspect ratio showing 100% of the size.
16:9 ZOOM
Use this aspect to Zoom-in once while in 16:9
aspect.
IMA G E INPUT
Note: Please see Appendix A
on page 88.
• Antenna-Digital Channel (4:3)
• S-Video/Video 4:3/Letter
Input (Auto Aspect: On)
• HDMI-480i/480p 4:3/
Letter Input (Auto Aspect: On)
• Component-480i/480p 4:3/
Letter Input
(Auto Aspect: On)
The Remote Control
4:3 EXPANDED
Use this aspect mode to display conventional (4:3)
sources by linearly increasing image expansion
from the center towards the edges of the display
area in order to fill it.
4:3 ZOOM1/ZOOM2
Use these aspect modes to zoom in on
conventional (4:3) sources.
1
IMA G E INPUT
Note: Please see Appendix A
on page 88.
• S-Video/Video 16:9 Input
(Auto Aspect: On)
• HDMI-480i/480p 16:9 Input
(Auto Aspect: On)
• Component-480i/480p
16:9 Input
(Auto Aspect: On)
Note: Please see Appendix A
on page 88.
• Antenna-Digital Channel (16:9)
• HDMI-720p/1080i Input
• Component-720p/1080i
Input
IMA G E INPUT
IMA G E INPUT
1
1
2
Note: Please see Appendix A
on page 88.
NOTE: 1. The Aspect Style in all five video inputs have independent Aspect Style setting.
2. Vertical position adjustments are directly available when you choose 4:3
EXPANDED/ZOOM1/ZOOM2 or 16:9 ZOOM aspect style (see also page 46).
.
3. When displaying 16:9 STANDARD 2 it may appear lines at the edge of the picture
this is normal operation of the TV.
25
How to Use the Remote to Control Your TV
When a Component Video: Y-PbPr
Input is connected to INPUT 3
햸 DAY/NIGHT button
Press this button to toggle between Day(Normal),
Day(Dynamic) and Night picture mode settings.
Select Day modes for day time viewing with more
brightness and contrast to compete with room light.
Select Night for nighttime viewing with less brightness
and contrast for a more detailed picture (see page 43
for settings changes).
NOTE:
Y-PBPR: 3
480i
햺 MENU button
The MENU button will start the On-Screen Display.
햻 INFO button
Press this button when you want to check the
channel being received, the picture source, if the
channel has stereo (ST) or second audio program
(SAP), the time, CHANNEL ID and if the TIMER is
set.
ANALOG CHANNELS
Program Information
Program Run Time
Show Name
3:00PM- 3:30PM
ST
INFO
TV-G
Broadcast
Rating
Audio
Broadcast
Auto
Main Picture Source
and channel indication
Broadcast channel
identification
Clock
Air
8
KXYZ-HD
3:17PM
480i
Audio Source
Selection
DIGITAL CHANNELS
Digital Closed Caption
This icon will appear only when
receiving a Digital Broadcast with
Closed Captioning.
Program Information
Show Name
3:00PM- 3:30PM
TV-G
ST
Program Run Time
INFO
ALT U.S.
Audio Broadcast
Broadcast Rating
DTvCC
Alternate
Rating
1080i
Auto
햽 EXIT button
This button will exit all On-Screen Displays.
햾 CURSOR PAD/SELECT button
All the On-Screen Display features can be set or
adjusted by using the CURSOR PAD, except for
numeric entries. The CURSOR PAD will highlight
functions or adjust and set different features. Press
the CURSOR PAD toward desired direction and
press the SELECT button to select.
햿 GUIDE button
Press this button to access the TV Guide On
ScreenTM interactive display (see page 49). Press
this button to access the Channel Guide of the
(CBL), and (SAT/STB) while in (CBL)(SAT/STB)
mode.
헀 INPUTS button
When the remote control is in TV mode, press this
button to access the INPUTS menu. Use the
CURSOR PAD and SELECT button to select the
inputs that are being used. Pressing the INPUTS
button repeatedly will also cycle through the Inputs
menu items. Then press the SELECT button to
select.
Picture Format
STEREO
Closed
Caption setting
3:17PM
Input Signal
Format
For automatic DAY/NIGHT picture mode
settings, see page 61.
햹 PICTURE-IN-PICTURE button
See separate section on pages 30-31 for a
description.
The Remote Control
INFO
Air
15-1
KPBS-HD
3:17PM
Main Picture Source
and channel indication
Broadcast channel
identification
Clock
Picture Format
Input 5
Photo Input
Air / Cable
Input 1
Input 2
Move
SEL Sel.
Program Desctiption
(Press INFO again for a more detailed description)
Auto
Closed
Caption setting
When an S-VIDEO Input is connected
to INPUT 1
INFO
S-IN: 1
480i
3:17PM
INPUT 1
INPUT 2
Select to choose INPUT 1.
Select to choose INPUT 2.
INPUT 3
Select to choose INPUT 3.
INPUT 4
Select to choose INPUT 4.
INPUT 5
Select to choose INPUT 5.
AIR / CABLE
Select between Cable or Air signal.
PHOTO INPUT Select to access your pictures from a
Auto
digital camera, USB memory or
memory card USB drive connected to
NOTE: 1.
2.
26
The Sleep Timer info will show
momentarily after releasing INFO button.
The Aspect setting will not be shown if
the channel is locked.
the Photo Input in the side panel of
the TV (see pages 27-28).
How to Use the Remote to Control Your TV
PHOTO INPUT
This feature is useful for viewing digital still pictures from your digital camera, USB Drive or memory cards USB
drive using the Photo Input in the left side panel of the TV.
1.
Press the INPUTS button to cycle through the
INPUTS selections until the PHOTO INPUT is
selected. Press the SELECT button or
CURSOR PAD .
Input 5
Photo Input
Air / Cable
Input 1
Input 2
Move
Press the CURSOR PAD or to access the
next or previous photo.
Next
3.
4.
5.
The Remote Control
2.
SEL Sel.
SEL Thumbnail
[0-9] Jump
Press the SELECT button to view
THUMBNAIL.
Use the CURSOR PAD buttons , , or and the SELECT button to navigate and select
individual chosen photos.
Press the picture number to jump from picture
to picture.
Please Enter
Picture Number
--
6.
7.
Press the INFO button to access PHOTO Input
menu and to view Photo information.
Press the CURSOR PAD or and the
SELECT button to navigate and select the
PHOTO Input menu.
NOTES:
1.
2.
3.
4.
5.
6.
7.
Picture No.
Date
Resolution
File Name
No. 02/08
06/13/05
2048x1536
DSC00467
Rotate
Slideshow
Device
Contrast will decrease automatically if stationary images such as digital still photos are left
on the screen for more than 3 minutes.
The maximum number of digital Photos that can be displayed is 999.
Press INFO button to show Picture Numbers in Thumbnail view, plus other information in
individual photos.
Digital photos recorded on a DVD-RAM disc may not work with this Photo Input.
Certain types of digital cameras may not work with this Photo Input.
Digital cameras with low battery power may not properly display your photos in this input.
The screen may show “Input device not detected” if the digital camera’s large capacity
memory is fully loaded, or because of slow access time on some digital cameras. Please
wait 1 or 2 minutes before checking your Photo Input connections.
27
How to Use the Remote to Control Your TV
ROTATE
Select this menu item to rotate selected photos
either clockwise (CURSORPAD ) and
counterclockwise (CURSOR PAD ).
The Remote Control
SLIDESHOW
Select this menu item to start a slideshow of the
digital photos. While the Interval sub menu is
highlighted, press the SELECT button to cycle
through the interval time from 5, 10 and 30 seconds.
Press the SELECT button to stop on a chosen
picture of the slideshow. After 30 seconds, the
slideshow will resume or press the SELECT button
again to continue with the slideshow.
DEVICE
Select this menu item to select the Photo Input
Device Drive when using a USB Drive device. Use
the CURSOR PAD or to select Device Drive.
Press the INFO button to highlight a device, then
press the SELECT button or CURSOR PAD to
access it. Use the CURSORPAD or to
the device to read.
NOTES:
1.
2.
3.
4.
28
Rotate
Slideshow
Device
Rotate
Slideshow
Device
Start
Interval
30sec
Drive B Automatic contrast reduction also applies during SLIDESHOW, then press any button to
continue.
Photo file names modified on a computer should be 8 characters (Ex. ABCD1234.jpg). 1st four
characters: Letters; 5th to 8th: Non duplicated numbers from 0001 to 9999. Photo files should be
first placed on a sub directory name with 8 characters (Ex. 123ABCDE). 1st to 3rd: Nonduplicated numbers from 0001 to 9999 4th to 8th: Letters. The sub directory then should be
placed on a main directory with a “dcim” file name format.
Supported image types are up to 3072 x 2304; JPEG format should conform with DCF
Standard (Design rule for Camera File System).
This TV set displays only digital pictures from digital cameras which meet DCF Standard.
Pictures that were copied, edited or modified on a computer may not be displayed on the TV
set.
How to Use the Remote to Control Your TV
헁 LAST CHANNEL (LAST CH) button
Press this button to toggle between the current and
last channel viewed.
헂 VOLUME (VOL) WHEEL, MUTE button
Use the VOL WHEEL ( or ) until you obtain the
desired sound level.
To reduce the sound to one half of normal volume
(SOFT MUTE) to answer the telephone, etc., press
the VOL wheel down. Press the VOL wheel again
to turn the sound off completely (MUTE). To
restore the sound, press the VOL wheel one more
time or VOL Up ().
Volume 8
Cable
Soft Mute 8
FAV Cable
The Remote Control
When using the Cursor up or down ( CH+ or CH-)
to change channel it will operate same as the
CHANNEL WHEEL except for the (FAV) channel
setting. The cursor up or down can only change
channels ; but to activate the (FAV) channels it
has to be activated from the CHANNEL WHEEL
only.
Press the channel (CH) wheel to switch to Favorite
(FAV) channel mode.You will know you are in
Favorite Channel mode when (FAV) is displayed
and the displayed channel is GREEN. Press it
again to return to your regular tuned channels.You
can add any channel to your Favorite channel list
by pressing and holding down the Channel (CH)
wheel until the displayed channel turns from WHITE
to highlighted GREEN.You can also delete a
channel from your favorite channel list by pressing
and holding down the Channel (CH) wheel until the
displayed channel turns highlighted GREEN to
WHITE.
22
22
/
Mute 8
Cable
22
/
Closed Captioning will display automatically when
MUTE/SOFT MUTE is on and Closed Caption is set
to AUTO (see page 65).
When the TV power is turned off at a volume level
31 or greater, the volume level will default to 30
when the TV is turned on. However, if it is set to a
level 30 or less, the volume level will be at the level
it was set when the TV is turned ON.
헄 (-) DASH button
Use the (-) DASHbutton with the CHANNEL
SELECTOR buttons to enter Digital Channels that
have subchannel numbers indicated by (-) DASH
(example 15-1).
헃 CHANNEL (CH) WHEEL/CHANNEL SELECTOR
buttons
The CHANNEL wheel or the CHANNEL SELECTOR
헅 BACKLIGHT button
buttons are used to select channels, lock access
Press this button to light up and illuminate the
code, etc. Use the CHANNEL WHEEL ( or ) to
buttons of the remote control.
select the desired channel. Use the CHANNEL
SELECTOR buttons to enter one, two, or three
numbers to select channels. Enter “0” first for
channels 1 to 9, or simply press the single digit
channel you wish to tune then wait a few seconds
for the TV to tune. For Digital Channels, use the
CHANNEL SELECTOR buttons with the (-) DASH
button. Channel selection may also be performed
by CHANNEL WHEEL up () , CHANNEL WHEEL
down () or CURSOR up ( CH+)& Cursor down ( CH-).
29
Picture-in-Picture (PIP)
Your HITACHI LCD TV incorporates one Tuner
technology designed for improved viewing enjoyment.
This feature allows you to view Digital Channels and
Video inputs on both the main picture and sub picture
simultaneously, with separate control.
When a Digital channel is viewed in the main picture,
the Digital or Analog channel can not be viewed in
the sub picture. Please see table for PIP availability.
CABLE
or
Air signal
To select between main picture and PIP sub picture,
use the CURSOR PAD button on the remote. The Green
highlighted PIP square will move with every press
of the CURSOR PAD buttons.
The Remote Control
The Picture-in-Picture feature is convenient when you
want to watch more than one program at the same
time. You can watch a TV program while viewing other
programs from any of the video inputs.
Use connection at right to view VCR program as a subpicture while viewing another program as main picture
(CABLE/AIR Digital channel).
Back of
VCR
AUDIO OUT
VIDEO OUT
OUTPUT
VCR
햲 PIP button
Press the PIP button and a sub-picture will appear
in one of the four different modes (POP, PIP, or
SPLIT), depending on the INPUT signal. To change
the PIP mode, use the PIP button to cycle through
the three different modes.
SPLIT MODE PICTURE-IN-PICTURE
Split Mode PIP displays the main picture and subpicture evenly on the screen.
햳
햲
SWAP
Main Picture
Sub Picture
+
POP MODE PICTURE-IN-PICTURE
POP Mode PIP displays the sub-picture outside of
the main picture. Use the CURSOR PAD ( or )
to move the sub-picture. This feature is not
available with a 1080i/720p signal. Please refer to the
PICTURE-IN-PICTURE MODES Table (see page
31).
Main Picture
Sub Picture
SWAP
NOTE :
30
1.
Press the CURSOR PAD ( or ) to
enable the sub-picture sound.
-
Picture-In-Picture (PIP)
PIP MODE PICTURE-IN-PICTURE
Select CABLE/AIR or INPUT 1~5 from the INPUTS menu. Select a channel that has a 1080i/720p signal.
Main Picture
Sub Picture
SW
AP
PIP Specifications Table
Sub Picture
Component/Composite/S-lN/HDMI
Digital Channel
The Remote Control
PIP
Mode
Main Picture
POP
Digital Ch.
(Air or Cable)
Component
Composite
S-IN
HDMI
PIP 16x9
Digital Ch.
(Air or Cable)
Component
Composite.
S-IN
HDMI
PIP 4x3
Digital Ch.
(Air or Cable)
Componet
Composite
S-IN
HDMI
SPLIT
Digital Ch.
(Air or Cable)
Component
Cmposite
S-IN
HDMI
STROBE
(4pix)
Digital Ch.
(Air or Cable)
Component
Composite
S-IN
HDMI
1080i
720p
480p
480p
480i
480i
1080i
720p
480p
480p
480i
480i
16x9
16x9
16x9
4x3
16x9
4x3
16x9
16x9
16x9
4x3
16x9
4x3
1080i
16x9
-
-
-
-
-
-
-
-
-
-
-
-
720p
16x9
-
-
-
-
-
-
-
-
-
-
-
-
480p
16x9
-
-
-
-
-
-
-
-
-
-
-
-
480p
4x3
-
-
-
-
-
-
Yes
Yes
Yes
Yes
Yes
Yes
480i
16x9
-
-
-
-
-
-
-
-
-
-
-
-
480i
4x3
-
-
-
-
-
-
Yes
Yes
Yes
Yes
Yes
Yes
1080i
16x9
-
-
-
-
-
-
-
-
-
-
-
-
720p
16x9
-
-
-
-
-
-
-
-
-
-
-
-
480p
16x9
Yes*l
Yes*l
Yes*l
Yes*l
Yes*l
Yes*l
-
-
-
-
-
-
480p
4x3
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
-
-
480i
16x9
Yes*l
Yes*l
Yes*l
Yes*l
Yes*l
Yes*l
-
-
-
-
-
-
480i
4x3
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
-
-
1080i
16x9
-
-
-
-
-
-
Yes
Yes
Yes*2
-
Yes*2
-
720p
16x9
-
-
-
-
-
-
Yes
Yes
Yes*2
-
Yes*2
-
480p
16x9
-
-
-
-
-
-
Yes
Yes
Yes*2
-
Yes*2
-
480p
4x3
-
-
-
-
-
-
-
-
-
-
-
-
480i
16x9
-
-
-
-
-
-
Yes
Yes
Yes*2
-
Yes*2
-
480i
4x3
-
-
-
-
-
-
-
-
-
-
-
-
1080i
16x9
Yes
Yes
Yes
-
Yes
-
-
-
-
-
-
-
720p
16x9
Yes
Yes
Yes
480p
16x9
480p
4x3
480i
16x9
Yes*2 Yes*2 Yes*2
—
—
—
Yes*2 Yes*2 Yes*2
-
Yes
-
-
-
-
-
-
-
-
Yes*2
-
-
-
-
-
-
-
-
—
-
-
-
-
-
-
-
-
Yes*2
-
-
-
-
-
-
-
480i
4x3
-
-
-
-
_
-
-
-
-
-
-
-
1080i
16x9
-
-
-
-
_
-
-
-
Yes*l
Yes
Yes*l
Yes
720p
16x9
-
-
-
-
-
-
-
-
Yes*l
Yes
Yes*l
Yes
480p
16x9
-
-
-
-
-
-
-
-
Yes*l
Yes
Yes*l
Yes
480p
4x3
-
-
-
-
-
-
-
-
-
-
-
-
480i
16x9
-
-
-
-
-
-
-
-
Yes*l
Yes
Yes*l
Yes
480i
4x3
1080i
16x9
-
-
-
Yes
-
Yes
-
-
-
-
-
-
720p
16x9
-
-
-
Yes
-
Yes
-
-
-
-
-
-
480p
16x9
-
-
-
Yes*2
-
Yes*2
-
-
-
-
-
-
480p
4x3
-
-
-
-
-
-
-
-
-
-
-
-
480i
16x9
-
-
-
Yes*2
-
Yes*2
-
-
-
-
-
-
480i
4x3
-
-
-
-
-
-
-
-
-
-
-
-
1080i
16x9
-
-
-
-
-
-
Yes
Yes
Yes
Yes
Yes
Yes
720p
16x9
-
-
-
-
-
-
Yes
Yes
Yes
Yes
Yes
Yes
480p
16x9
-
-
-
-
-
-
Yes
Yes
Yes
Yes
Yes
Yes
480p
4x3
-
-
-
-
-
-
Yes
Yes
Yes
Yes
Yes
Yes
480i
16x9
-
-
-
-
-
-
Yes
Yes
Yes
Yes
Yes
Yes
480i
4x3
-
-
-
-
-
-
Yes
Yes
Yes
Yes
Yes
Yes
1080i
16x9
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
-
-
720p
16x9
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
-
-
480p
16x9
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
-
-
480p
4x3
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
-
-
480i
16x9
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
-
-
480i
4x3
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
-
-
1080i
16x9
Yes
-
-
-
-
-
-
-
-
-
-
-
720 p
16x9
-
Yes
-
-
-
-
-
-
-
-
-
-
480p
16x9
-
-
Yes
-
-
-
-
-
-
-
-
-
480p
4x3
-
-
-
Yes
-
-
-
-
-
-
-
-
480i
16x9
-
-
-
-
Yes
-
-
-
-
-
-
-
480i
4x3
-
-
-
-
-
Yes
-
-
-
-
-
-
1080i
16x9
-
-
-
-
-
-
Yes
_
-
-
-
-
720p
16x9
-
-
-
-
-
-
-
Yes
-
-
-
-
480p
16x9
-
-
-
-
-
-
-
-
Yes
-
-
-
480p
4x3
-
-
-
-
-
-
-
-
-
Yes
-
-
480i
16x9
-
-
-
-
-
-
-
-
-
-
Yes
480i
4x3
-
-
-
-
-
-
-
-
-
-
-
Yes
Yes* l: Auto Aspect OFF
Yes*2: Aulo Aspect ON
( - ) : Not available
31
Picture-In-Picture (PIP)
햳 PAUSE button
If you wish to freeze the sub-picture, press the
PAUSE button. This is convenient when trying to
write down the address for a mail order company,
recording statistics for a sporting event, etc. To
return the picture to motion, press the EXIT
button. Press the PAUSE button repeatedly to
toggle between FREEZE modes (Main Freeze,
SPLIT and STROBE).
The Remote Control
Freeze
SPLIT FREEZE
Press the PAUSE button to freeze the picture you
are currently viewing (only the right sub-picture will
freeze). Press the EXIT button to return to normal
viewing.
Main Picture
Sub Picture
Freeze
Freeze
Freeze
Freeze
STROBE FREEZE
Press the PAUSE button to freeze three frames of
the picture you are currently viewing (only the 3
sub-pictures will freeze). Press the EXIT button to
return to normal viewing. This feature is useful for
viewing a moving picture that has many details, for
example, a close play in a sporting event or a golf
swing.
MAIN FREEZE
Press the PAUSE button to freeze one frame of the
picture you are currently viewing and the frozen
frame will show in the Main Picture. Press the EXIT
button to return to normal viewing. This feature is
useful for freezing a picture frame with addresses.
Hot Springs Clay Mask
C/O John Doe
Run-Spa Retreat
P.O. Box 55512
Any Town, USA 98765
Check or
Money Order Only
1-800-555-1212
NOTE: 1. The default FREEZE mode is the MAIN
freeze followed by the SPLIT freeze and
then the STROBE freeze. The last FREEZE
mode you selected before you pressed the
EXIT button will be the one that comes up
after pressing the PAUSE button again.
2. Each freeze frame in Strobe Freeze is
delayed about 0.1 (1/10) second.
32
The Remote Control for Cable Box Functions
Operating the precoded function for your cable
box.
햲
This remote is designed to operate different types of
cable boxes. You must first program the remote to
match the remote system of your cable box (refer to
pages 39-40 for pre-codes).
1.
Turn ON your cable box.
2.
Aim the remote control at the front of your cable
box.
3.
5.
6.
To switch to Cable (CBL) pre-coded mode, use the
SOURCE ACCESS buttons ( or ) on the remote
control to position the LED light to the
corresponding selection.
Hold down the ENT button on the remote and enter
the four digit preset code that matches your cable
box as shown on pages 39-40. Release the ENT
button. The indicator light will flash 3 times if the
code was accepted.
Aim the remote at the cable box and press the
POWER button. The remote will turn off your cable
box when the correct four digit preset code is
entered. When this occurs, the remote control is
programmed for your cable box. If the cable box
does not turn off, try a different four digit preset
code.
+
햲
The Remote Control
4.
햳
햲
-
햳
/
햳
햲
햲
The remote will now control your Cable box.
NOTE: 1. If your cable box cannot be operated after
performing the above procedures, your
cable box code has not been precoded
into the remote.
2. In the unlikely event that your cable box
cannot be operated after performing the
above procedures, please consult your
cable box operating guide.
3. The remote control will remember the
codes you have programmed until the
batteries are removed from the
remote control. After replacing the
batteries repeat the entire programming
procedure as stated above.
햲 PRECODED CABLE BOX buttons
These buttons transmit the chosen precoded cable
codes.
MY CABLE BOX CODE IS:
NOTE: Refer to instruction manual of the Cable Box
for operation of the buttons exclusively for
the Cable Box.
햳 EXCLUSIVE TV buttons
These buttons are for operating the TV.
33
The Remote Control for Set-Top-Box/Satellite Receiver Functions
Operating the precoded function for your set-topbox/satellite receiver.
햲
The Remote Control
This remote is designed to operate different types of
set-top-box/satellite systems. You must first program
the remote to match the remote system of your settop-box/satellite systems (refer to pages 39-40 for precodes).
1.
Turn ON your set-top-box/satellite systems.
2.
Aim the remote control at the front of your set-topbox/satellite systems.
3.
To switch to set-top-box/satellite (STB) pre-coded
mode, use the SOURCE ACCESS buttons ( or )
on the remote control to position the LED light to
the corresponding selection.
4.
Hold down the ENT button on the remote and enter
the four digit preset code that matches your settop-box/satellite receiver as shown on page 39-40.
Release the ENT button. The indicator light will
flash 3 times if the code was accepted.
햳
+
햲
햲
-
햳
/
5.
6.
Aim the remote at the set-top-box/satellite receiver
and press the POWERbutton. The remote will turn
off your set-top-box/satellite receiver when the
correct four digit preset code is entered. When this
occurs, the remote control is programmed for your
set-top-box/satellite receiver. If the set-topbox/satellite receiver does not turn off, try a
different four digit preset code.
햲
햲
The remote will now control your set-topbox/satellite receiver.
NOTE: 1. If your set-top-box/satellite receiver
cannot be operated after performing the
above procedures, your set-top-box/
satellite receiver code has not been
precoded into the remote.
2. In the unlikely event that your set-topbox/satellite receiver cannot be operated
after performing the above procedures,
please consult your set-top-box/satellite
receiver operating guide.
3. The remote control will remember the
codes you have programmed until the
batteries are removed from the
remote control. After replacing the
batteries repeat the entire programming
procedure as stated above.
햲 PRECODED SET-TOP-BOX/SATELLITE
RECEIVER buttons
These buttons transmit the chosen pre-coded settop-box/satellite codes.
햳 EXCLUSIVE TV buttons
These buttons are for operating the TV.
34
햳
MY Satellite RECEIVER/
SET-TOP-BOX CODE IS:
NOTE: Refer to instruction manual of the Set-TopBox/Satellite Receiver for operation of the
buttons exclusively for the Set-TopBox/Satellite Receiver.
The Remote Control for DVD Functions
Operating the precoded function for your DVD
player.
햲
This remote is designed to operate different types of
DVD players. You must first program the remote to
match the remote system of your DVD player (refer to
pages 39-40 for pre-codes).
1.
Turn ON your DVD player.
2.
Aim the remote control at the front of your DVD
player.
3.
5.
햳
To switch to DVD pre-coded mode, use the
SOURCE ACCESS buttons ( or ) on the remote
control to position the LED light to the
corresponding selection.
Hold down the ENT button on the remote and enter
the four digit preset code that matches your DVD
player, as shown on pages 39-40. Release the
ENT button. The indicator light will flash 3 times if
the code was accepted.
Aim the remote at the DVD player and press the
POWER button. The remote will turn off your DVD
player when the correct four digit preset code is
entered. When this occurs, the remote control is
programmed for your DVD player. If the DVD
player does not turn off, try a different four digit
preset code.
6.
The remote will now control your DVD player.
7.
You will need to set the display type of your DVD
player to 16:9 widescreen.
NOTE: 1. If your DVD player cannot be operated
after performing the above procedures,
your DVD player code has not been
precoded into the remote.
2. In the unlikely event that your DVD player
cannot be operated after performing the
above procedures, please consult your
DVD player operating guide.
3. The remote control will remember the
codes you have programmed until the
batteries are removed from the
remote control. After replacing the
batteries repeat the entire programming
procedure as stated above.
+
햲
The Remote Control
4.
햲
햲
-
햳
햳
/
햲
MY DVD PLAYER CODE IS:
NOTE: Refer to instruction manual of the DVD Player
for operation of the buttons exclusively for
the DVD Player.
햲 PRECODED DVD Buttons
These buttons transmit the chosen precoded DVD
codes.
햳 EXCLUSIVE TV Buttons
These buttons are for operating the TV.
35
The Remote for VCR/PVR Functions
Operating the precoded function for your
VCR/PVR (Personal Video Recorder).
햲
This remote is designed to operate different types of
VCRs/PVRs. You must first program the remote to
match the remote system of your VCR/PVR (refer to
pages 39-40 for pre-codes).
1.
Turn ON your VCR/PVR.
2.
Aim the remote control at the front of your
VCR/PVR.
The Remote Control
3.
4.
5.
6.
햳
To switch to VCR/PVR pre-coded mode, use the
SOURCE ACCESS buttons ( or ) on the remote
control to position the LED light to the
corresponding selection.
Hold down the ENT button on the remote and enter
the four digit preset code that matches your
VCR/PVR, as shown on pages 39-40. Release the
ENT button. The indicator light will flash 3 times if
the code was accepted.
Aim the remote at the VCR/PVR and press the
POWER button. The remote will turn off your PVR
when the correct four digit preset code is entered.
When this occurs, the remote control is
programmed for your VCR/PVR. If the VCR/PVR
does not turn off, try a different four digit preset
code.
+
햲
햳
햲
-
/
햲
햲
The remote will now control your VCR/PVR.
NOTE: 1. If your VCR/PVR cannot be operated after
performing the above procedures, your
VCR/PVR code has not been precoded
into the remote.
2. In the unlikely event that your VCR/PVR
cannot be operated after performing the
above procedures, please consult your
VCR/PVR operating guide.
3. The remote control will remember the
codes you have programmed until the
batteries are removed from the
remote control. After replacing the
batteries repeat the entire programming
procedure as stated above.
햲 PRECODED VCR/PVR Buttons
These buttons transmit the chosen precoded
VCR/PVR codes.
햳 EXCLUSIVE TV Buttons
These buttons are for operating the TV.
36
햲
MY VCR/PVR CODE IS:
NOTE: Refer to instruction manual of the VCR/PVR
for operation of the buttons exclusively for
the VCR/PVR.
The Remote Control for Additional Audio Equipment
Operating the precoded function for your Audio
component.
햲
This remote is designed to operate different types of
Audio component. You must first program the remote
to match the remote system of your Audio component
(refer to pages 39-40 for pre-codes).
1.
Turn ON your Audio component you wish to control
with the Remote.
2.
Aim the remote control at the front of your Audio
component.
3.
햳
햲
To switch to Audio (AMP) component pre-coded
mode, use the SOURCE ACCESS buttons ( or )
on the remote control to position the LED light to
the corresponding selection.
Hold down the ENT button on the remote and enter
the four digit preset code that matches your Audio
component, as shown on pages 39-40. Release
the ENT button. The indicator light will flash 3
times if the code was accepted.
+
햳
햳
-
/
5.
Aim the remote at the Audio component and press
the POWERbutton. The remote will turn off your
Audio component when the correct four digit
preset code is entered. When this occurs, the
remote control is programmed for your Audio
component. If the Audio component does not turn
off, try a different four digit preset code.
6.
The remote will now control your Audio
component.
7.
Repeat steps 1 - 6 if you wish to program the
remote to control another Audio component.
NOTE: 1. If your Audio component cannot be
operated after performing the above
procedures, your Audio component code
has not been precoded into the remote.
2. In the unlikely event that your Audio
component cannot be operated after
performing the above procedures, please
consult your Audio component operating
guide.
3. The remote control will remember the
codes you have programmed until the
batteries are removed from the
remote control. After replacing the
batteries repeat the entire programming
procedure as stated above.
The Remote Control
4.
햲
햲
햲
MY AUDIO COMPONENT
CODE IS:
NOTE: Refer to instruction manual of the VCR/PVR
for operation of the buttons exclusively for
the VCR/PVR.
햲 PRECODED AUDIO Buttons
These buttons transmit the chosen precoded Audio
component codes.
햳 EXCLUSIVE TV Buttons
These buttons are for operating the TV.
37
How to Use the ENT Button
INPUT ACCESS
This optional feature allows the user of the remote
control to setup it’s ENTER (ENT) button to access the
specified input of the TV. Setup for this feature is
applicable to the remote control’s normal mode only
and only applies to the DVD, CBL, STB, PVR and AMP
modes.
1.
The Remote Control
2.
3.
, , Select the desired device mode (DVD, CBL, STB,
PVR, or AMP) by using your SOURCE ACCESS
buttons ( or ) to position the LED indicator to
the corresponding selection.
+
Hold down the ENTER (ENT) button on the remote
and enter the four digit preset code that
matches your device as shown on pages 39-40.
-
Then enter the assigned input number (1-5) that the
device is related to.
4.
Release ENTER (ENT) button.
5.
If done correctly, the device LED indicator will flash
3 times to confirm proper setup.
6.
The remote will now control the desired device.
7.
Pressing the ENTER (ENT) button will now access
the video input (1-5) of the desired device.
, , /
SETUP EXAMPLE (Hitachi DVD with precode
0573 connected to INPUT 1 of the TV)
38
Select DVD mode by using your SOURCE ACCESS
buttons ( or ) to position the LED indicator to
DVD.
Hold down the ENTER (ENT) button and press the
numbers 0, 5, 7 and 3.
Then press the number 1 for the assigned input
number of the DVD player.
Release ENTER (ENT) button.
If done correctly, the device LED indicator will flash
3 times to confirm proper setup.
The remote will now control the DVD player.
Press the ENTER (ENT) button to instantly access
the video input of your DVD on Input 1.
NOTE: 1. This feature is optional
2. Assigned input numbers can be used more
than once if applicable.
Remote Control Codes
Marta ................................0037
Matsushita ....0035, 0162, 1162
Media Center PC ..............1972
Memorex ......0035, 0162, 0037,
..........0048, 0039, 0047, 0240,
..........0000, 0104, 0209, 0046,
..0307, 0479, 1037, 1162, 1262
Microsoft ............................1972
Mind ..................................1972
Minolta ....................0042, 0105
Mitsubishi .... 0061, 0043, 0067
Motorola ..................0035, 0048
Multitech ..................0000, 0072
NEC ....0038, 0041, 0067, 0104
Nikko..................................0037
Noblex ..............................0240
Northgate ..........................1972
Olympus ............................0035
Optimus ........0593, 1062, 0162,
..........0037, 0048, 0104, 0432,
......................1048, 1162, 1262
Optonica ............................0062
Orion....0184, 0209, 0002, 0479
Panasonic ....0162, 1062, 0035,
......................0616, 1162, 1262
Penney0035, 0037, 0240, 0042,
..........................................0038
Pentax ....................0042, 0105
Philco ..0035, 0209, 0479, 0561
Philips ..........0081, 0035, 0618,
......................1081, 1181, 0062
Pilot....................................0037
Pioneer ..............................0067
Polk Audio..........................0081
Profitronic ..........................0240
Proscan ........0060, 0202, 0761
Protec ................................0072
Pulsar ................................0039
Quarter ..............................0046
Quartz................................0046
Quasar ..........0035, 0162, 1162
RCA....0060, 0240, 0042, 0105,
............0106, 0202, 0761, 0880
Radio Shack ............0000, 1037
Radix ................................0037
Randex. ............................0037
Realistic........0035, 0037, 0048,
..........0047, 0000, 0104, 0046,
................................0062, 0066
ReplayTV ................0614, 0616
Runco ................................0039
STS....................................0042
Samsung ......0045, 0240, 0432
Sanky ......................0039, 0048
Sansui ..........0000, 0067, 0209,
............0041, 0479, 1479, 0271
Sanyo ..0047, 0240, 0104, 0046
Scott ............0184, 0045, 0121,
......................0043, 0210, 0212
Sears ..0035, 0037, 0047, 0000,
0042, 0104, 1237, 0046, 0066,
..........................................0105
Semp. ................................0045
Sharp ............0048, 0848, 0062
Shintom ............................0072
Shogun ..............................0240
Singer ................................0072
Sonic Blue ..............0614, 0616
Sony ............0035, 0032, 0000,
............0033, 0636, 1032, 1972
Sylvania........0035, 0081, 0000,
......................0043, 0593, 1593
Symphonic ....0000, 0593, 1593
Systemax ..........................1972
TMK ........................0240, 0208
Tagar Systems ..................1972
Tatung................................0041
Teac ........................0000, 0041
Technics ..................0035, 0162
Teknika ..........0000, 0035, 0037
Thomas..............................0000
Tivo................0618, 0636, 1503
Toshiba ........0045, 0043, 0066,
..........0210, 0212, 0366, 0845,
............1008, 1145, 1503, 1972
Totevision ................0037, 0240
Touch ................................1972
Unitech ..............................0240
Vector ................................0045
Vector Research ................0038
Video Concepts ......0045, 0061
Videomagic ........................0037
Videosonic ........................0240
Viewsonic ..........................1972
Wards 0060, 0062, 0035, 0048,
..........0047, 0081, 0240, 0000,
......................0042, 0072, 0212
White Westinghouse..................
................................0072, 0209
XR-1000 ........0072, 0000, 0035
Yamaha ............................0038
ZT Group ..........................1972
Zenith 0039, 0000, 0209, 0033,
................................0479, 1479
DVD BRAND ..................CODE
AMW..................................0872
Aiwa ..................................0641
Allegro ..............................0869
Apex Digital ..0672, 0717, 0755,
0794, 0796, 0797, 1004, 1020,
..1056, 1061, 1100, 1915, 1937
Audiovox..................0790, 1072
Axion..................................1072
Blaupunkt ..........................0717
Blue Parade ......................0571
Brooksonic ........................0695
CAVS ................................1057
CineVision ..............0876, 0869
Classic ..............................1917
Coby ..................................1086
Curtis Mathes ....................1087
CyberHome ..0816, 1023, 1024
DVD2000 ..........................0521
Daewoo ..................0784, 0705,
......................0833, 0869, 1918
Denon ......................0490, 0634
Dual ........................1068, 1085
Emerson ..................0591, 0675
Enterprise ..........................0591
Fisher ................................0670
Funai..................................0675
GE ................0522, 0717, 0815
GPX ........................0699, 0769
Gateway ............................1073
Go Video ......0744, 0715, 0783,
......................0833, 0869, 1075
Gradiente ..........................0651
Greenhill ............................0717
Grundig..............................0705
Harman/Kardon ................0702
Hitachi ..........0573, 0664, 0695
Hiteker ..............................0672
IRT ....................................0783
Initial ..................................0717
Integra ..............................0627
Hiteker ..............................0672
JBL ....................................0702
JVC......0623, 0558, 0867, 1901
KLH ..............0717, 0790, 1020
Kawasaki ..........................0790
Kenwood..................0490, 0534
Koss ..................................0651
Lasonic ..............................0798
Lite-On ..............................1058
Magnavox ..............0503, 0675,
................................1914, 1976
Marantz..............................0539
Memorex............................0695
Microsoft ............................0522
Mintek ......................0717, 0839
Mitsubishi ................0521, 1521
Nesa ..................................0717
Norcent ....................1003, 0872
Onkyo ......................0627, 0503
Oritron................................0651
Panasonic..........................0490
Philco ................................0790
Philips..0503, 0539, 0646, 0854
Pioneer ..........0525, 0571, 1902
Polaroid ..................1061, 1086
Polk Audio..........................0539
Proscan ............................0522
Qwestar ............................0651
RCA..............0522, 0571, 0717,
......................0790, 0822, 1974
Recco ................................0698
Rio ....................................0869
Rotel ..................................0623
Rowa ................................0823
Sampo ....................0698, 0752
Samsung ................0490, 0573,
......................0820, 0744, 1075
Sansui................................0695
Sanyo ............0670, 0695, 0873
Semp ................................0503
Sharp ......................0630, 0752
Shinsonic ................0533, 0839
Sonic Blue ........................0869
Sony ..................................0533
Sylvania ............................0675
Symphonic ........................0675
TYT....................................0705
Teac ..................................0790
Technics ............................0490
Theta Digital ......................0571
Tivo ....................................1996
Toshiba ........0503, 0695, 1045,
......................1988, 1996, 2006
Tredex ....................0799, 0803
US Logic ............................0839
Urban Concepts ................0503
Venturer ............................0790
XBox ..................................0522
Yamaha ........0490, 0545, 0539
Zenith ............0591, 0503, 0869
The Remote Control
VCR BRAND ..................CODE
ABS ..................................1972
Admiral ....................0048, 0209
Adventura .........................0000
Aiko....................................0278
Aiwa ..............0000, 0037, 0307
Akai ..............0041, 0061, 0106
Alienware ..........................1972
America Action ..................0278
American High ..................0035
Asha ..................................0240
Audiovox..................0037, 0278
Beaumark ..........................0240
Bell & Howell ....................0104
Broksonic................0121, 0184,
......................0002, 0209, 0479
CCE ........................0072, 0278
Calix ..................................0037
Canon ................................0035
Carver................................0081
Cineral ..............................0278
Citizen......................0278, 0037
Colt ....................................0072
Craig ......................0037, 0072,
......................0047, 0240, 0271
Curtis Mathes ........0035, 0041,
................................0060, 0162
CyberPower ......................1972
Cybernex ..........................0240
Daewoo ........0278, 0045, 0561
Dell ....................................1972
Denon ................................0042
Durabrand................0039, 0038
Dynatech ..........................0000
Electrohome ......................0037
Electrophonic ....................0037
Emerex ..............................0032
Emerson0037, 0184, 000, 0121,
0043, 0209, 0002, 0278, 0061,
..0208, 0212, 0479, 0561, 1593
Fisher ............0104, 0047, 0066
Fuji ..........................0033, 0035
Funai........................0000, 1593
GE ................0035, 0060, 0240,
................................0202, 0761
Garrard ..............................0000
Gateway ..........................1972
Go Video ................0432, 0526
GoldStar ..................0037, 0038
Gradiente ................0000, 0008
HI-Q ..................................0047
HP......................................1972
Harley Davidson ................0000
Harman/Kardon ......0038, 0081
Harwood ............................0072
Headquarter ......................0046
Hewlett Packard ................1972
Hitachi 0000, 0041, 0042, 0105
Howard Computers............1972
Hughes Network Systems 0042
iBuy Power ........................1972
JVC................0067, 0041, 0008
Jensen ..............................0041
KEC ........................0037, 0278
KLH....................................0072
Kenwood ......0041, 0067, 0038
Kodak ......................0035, 0037
LG......................................0037
LXI ....................................0037
Lloyd's ....................0000, 0208
Logik ..................................0072
MEI ....................................0035
MGA ..............0043, 0240, 0061
MGN Technology ..............0240
MTC ........................0000, 0240
Magnasonic ......................0593
Magnavox ....0035, 0081, 0563,
0000, 0039, 0593
Magnin ..............................0240
Marantz....................0081, 0035
CABLE BRAND..............CODE
ABC ....0003, 0008, 0011, 0013,
................................0014, 0017
Allegro ....................0153, 0315
Americast ..........................0899
Antronix ..............................022
Archer..............022, 0153, 0797
Bell & Howel .....................0014
Bell South ..........................0899
Cabletenna ........................0022
Cableview ..........................0022
Century ..............................0153
Citizen......................0153, 0315
ClearMax ..........................0883
Clearmaster ......................0883
Colour Voice ............0025, 0031
Comtronics ........................0040
Contec ..............................0019
Coolmax ............................0883
Digi ....................................0637
Director ..............................0476
Dumont ..............................0637
Emerson ............................0797
Everquest ................0015, 0040
Focus ................................0400
Garrard ..............................0153
Gemini ....................0015, 0797
General Instrument 0003, 0011,
......................0476, 0276, 0810
GoldStar ..................0040, 0144
Goodmind ..........................0797
Hamlin 0009, 0020, 0034, 0273
Hitachi ................................0011
39
The Remote Control
Remote Control Codes
40
Jasco ............0015, 0153, 0315
Jerrold ......... 0003, 0011, 0012,
0014, 0015, 0024, 0276, 0476,
..........................................0810
Memorex ...........................0000
Motorola ...... 0276, 0476, 0810,
......................1106, 1254, 1376
Movie Time ........................0063
Multivision..........................0012
NSC ..................................0063
Novaplex............................0618
Oak ....................................0019
Optimus ............................0021
Pace ........................0237, 1877
Panasonic......0000, 0021, 0107
Panther ..............................0637
Paragon ............................0000
Philips ......................0305, 0317
Pioneer0023, 0025, 0031, 0153,
............0144, 0533, 0877, 1877
Popular Mechanics ............0400
Pulsar ................................0000
Quasar...............................0000
RCA ..................................0021
RadioShack ..0015, 0315, 0797,
..........................................0883
Recoton ............................0400
Regal .............0020, 0273, 0279
Rembrandt ........................0011
Runco ...............................0000
SL Marx ............................0040
Samsung .................0040, 0144
Scientific Atlanta ....0877, 0008,
......................0017, 0477, 1877
Signal ......................0015, 0040
Signature ..........................0011
Sony ..................................1006
Sprucer ..............................0021
Starcom ..................0003, 0015
Stargate ........0015, 0040, 0797
Starquest ..........................0015
Supercable ........................0276
Supermax ..........................0883
TFC....................................0310
TV86 ..................................0063
Tandy ................................0258
TeleCaption........................0221
Teleview ............................0040
Timeless ............................0040
Tocom ......................0012, 0013
Torx....................................0003
Toshiba ..............................0000
Tristar ................................0883
Tusa ..................................0015
Unika ......................0022, 0153
Universal ......0022, 0153, 0191
V2 ......................................0883
ViewMaster ........................0883
Viewstar ..................0063, 0258
Vision ................................0883
Vortex View........................0883
Zenith ..0000, 0054, 0525, 0899
Zentek................................0400
............1639, 1142, 0247, 0749,
..........1749, 0724, 0819, 1856,
............1076, 1109, 0099, 1052,
..1053, 1054, 1442, 1443, 1444
Dish Network System ......1005,
0775, 1170
DishPro....................1005, 0775
Drake ............0018, 0064, 0245
Echostar ......1005, 0775, 0148,
......................0269, 0280, 1170
Expressvu..........................0775
GE ....................................0566
GOI ....................................0775
General Instrument ..........0869,
................................0547, 0554
Gradiente ..........................0856
HTS ..................................0775
Hitachi................................0819
homecable ........................0238
Hughes Network Systems 1142,
..0749, 1749, 1442, 1443, 1444
Hytek ................................0095
IQ ......................................0210
IQ Prism ............................0210
Innova................................0099
Intersat ..............................0043
JVC ..........................0775, 1170
Janeil ................................0152
Legend ..............................0269
Macom ....................0018, 0061
Magnavox ................0724, 0722
Memorex..................0724, 0269
Mitsubishi ..........................0749
Motorola ............................0869
Netsat ................................0099
Next Level..........................0869
Norsat ................................0004
Pace ..................................0455
Panasonic......0247, 0701, 0152
Paysat................................0724
Philips 1142, 0749, 0724, 1076,
............0722, 1749, 0856, 0099
Pico....................................0075
Proscan ..................0392, 0566
RCA ....0392, 0566, 0855, 0143
Radioshack..............0869, 0554
Ramsey ............................0075
Realistic ............................0052
SKY ..............0856, 1856, 0099
STS..........................0041, 0210
Samsung..................1276, 1109
Sony ........................0639, 1639
Star Choice........................0869
Star Trak........0180, 0421, 0547
Strong ................................0421
Tivo ......1142, 1442, 1443, 1444
Toshiba ........0749, 1749, 0790,
..........0061, 0082, 1052, 1053,
..1054, 1285, 1286, 1287, 1289
Town & Country ................0547
Uniden 0724, 0722, 0052, 0074,
............0076, 0238, 0370, 0554
Zenith ..0856, 1856, 0061, 0064
SATELLITE BRAND (Set-TopBox) ................................CODE
AlphaStar ..........................0772
Amway ....................0043, 0075
Astro Industries..................0095
BSR ..................................0095
Cable Innovations..............0554
Capetronic ........................0095
Century ..............................0856
Channel Master ......0018, 0212
Chapparral ....0053, 0209, 0216
Conifer ..............................0004
Crossdigital ........................1109
Curtis Mathes ......................061
DX Antenna ......................0041
DirecTV ........0392, 0566, 0639,
AMPLIFIER BRAND ......CODE
Aiwa...................................0406
Bose ..................................0674
Carver................................0269
Curtis Mathes ...................0300
Denon ...............................0160
Durabrand..........................1561
GE .....................................0078
Harman/Kardon .................0892
JVC ...................................0331
Left Coast ..........................0892
Lenoxx ..............................1561
Linn ...................................0269
Luxman..............................0165
Magnavox ..........................0269
Marantz ........0269, 0321, 0892
NEC ..................................0264
Nakamichi..........................0321
Optimus ..................0395, 0300
Panasonic................0308, 0521
Parasound ........................0246
Philips ......................0269, 0892
Pioneer ....................0013, 0300
Polk Audio ..............0269, 0892
RCA ..................................0300
Realistic .............................0395
Sansui................................0321
Shure ................................0264
Sony ..............0815, 0689, 0220
Soundesign..............0078, 0211
Technics ..................0308, 0521
Toshiba ..............................0353
Victor ................................0331
Wards ............0013, 0078, 0211
Yamaha ..................0354, 0133
RECEIVER BRAND (Amplifier)
CODE
ADC ..................................0531
Aiwa....1405, 0121, 0158, 0189,
0405
Anam ......................1074, 1609
Arcam ................................1120
Audiotronic ........................1189
Bose ..............0639, 1229, 1253
Capetronic .........................0531
Carver ............1189, 0042, 0189
Casio ................................0195
Clarinette ..........................0195
Coby ..................................1263
Compaq ............................1136
Curtis Mathes ....................0080
Dell ....................................1383
Denon .....................0004, 1360
Fisher ................................0042
Garrard ..............................0463
Glory Horse ......................1263
Harman/Kardon ......0891, 0110,
0189
Hewlett Packard ................1181
Hitachi................................0228
Integra ..............................0135
JBL ....................................0110
JVC..........................0074, 1263
KLH....................................1428
Kenwood ......1313, 1570, 1569,
............0027, 0042, 0186, 0239
LXI ....................................0181
Linn ...................................0189
Lloyd's................................0195
MCS ..................................0039
Magnavox ....1189, 1269, 0189,
0195, 0391, 0531
Marantz1189, 0039, 0189, 1269
Mitsubishi ..........................1393
Modulaire ..........................0195
Musicmagic........................1089
Nakamichi..........................0097
Onkyo ......................0135, 0842
Optimus ........1023, 0042, 0080,
..........0177, 0181, 0186, 0219,
..0531, 0670, 0738, 0801, 1074
Panasonic ....1518, 0039, 0309,
0367
Penney ..............................0195
Philips ..........1189, 1269, 0189,
................................0391, 1120
Pioneer ........1023, 0014, 0080,
............0150, 0244, 0531, 0630
Polk Audio..........................0189
Proscan ............................1254
Quasar ..............................0039
RCA..............1023, 1254, 0080,
......................0531, 1074, 1609
Radio Shack ......................1263
Realistic ..................0181, 0195
Rio ....................................1383
Sansui................................0189
Sanyo ......................0801, 1251
Scott ........................0163, 0322
Sharp ................................0186
Sharper Image ..................1263
Sherwood ................0491, 0502
Sonic Blue ........................1383
Sony ..1058, 1441, 1759, 0158,
............0474, 1349, 1406, 1442
Soundesign........................0670
Stereophonics....................1023
Sunfire ..............................1313
Teac ........................0463, 1074
Technics..................1308, 1518,
................................0039, 0309
Thorens..............................1189
Toshiba ..............................1572
Victor ................................0074
Wards .0014, 0080, 0158, 0189
Yamaha..........0176, 0186, 1176
Yorx. ..................................0195
Zenith ................................0857
AUDIO BRAND ..............CODE
Aiwa ........................0010, 0159
AudioSource ......................0351
Cambridge Soundworks ....0351
Carver................................0351
Fisher ................................0052
Fosgate..............................0259
Harmon/Kardon ................0477
JBL ....................................0477
JVC....................................0073
KLH....................................0351
Magnavox ..........................0325
Nikko..................................0376
Paramount Pictures 0317, 0351
RCA ..................................0056
SSI ....................................0317
Sansui................................0325
Schneider ..........................0376
Sony ........................0010, 0576
Soundesign........................0376
Yorx....................................0376
SET TOP BOX BRAND ..CODE
Panasonic ..........................1120
Pioneer ..............................1010
Princeton..................0113, 0295
Samsung............................1190
Sensory Science................1126
Sharp ................................1010
Sony ..................................0639
PERSONAL VIDEO
RECORDER BRAND......CODE
Panasonic..........................0616
Philips ................................0618
ReplayTV ................0614, 0616
SonicBlue ................0614, 0616
Sony ..................................0636
Tivo..........................0618, 0636
On-Screen Display
1.
Press MENU on the remote control to display the
different features on your HITACHI LCD TV.
2.
Use the CURSOR PAD (buttons , , and ) or
CHANNEL WHEEL to navigate to a different menu
item.
3.
Press EXIT on the remote control to quickly exit
from a menu.
This part of the screen shows
which selections are available.
Vide o
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move
SEL Select
This part of the screen
shows which Remote
Control buttons to use.
Picture Mode
White Level
Black Level
Auto Movie Mode
Select between 3 pictures modes;
Day (Dynamic), Day (Normal) and Night.
Adjust picture white level.
Adjust picture black level.
Color
Tint
Sharpness
Adjust color.
Adjust tint.
Adjust sharpness.
Motion Sharpness
Select between 3 sharpness modes
to increase detail on moving pictures.
Back Light
Adjust the intensity of the panel back
light.
Set this to High for less intense
color with more blue, set to
Medium for natural color, set to
Standard for standard colors or
Black and White for more
reddish color.
Enhance picture brightness in
light scenes.
Use this function to choose
between 2 Contrast Mode
settings.
Reduces conspicuous noise in
the picture.
Color Temperature
Black Enhancement
Contrast Mode
Noise Reduction
Color Management
Color Decoding
Auto Color
White Balance
Black Side Panel
Aspect
Reset Video Settings
Turn On/Off the 3:2 Pulldown
detection feature.
Adjust and balance individual
colors to make either deeper or
more pure according to
preference.
Adjust the percentage of Red,
Green and Color according to
preference.
The AUTO COLOR function
automatically monitors and
adjusts the color to maintain
constant color levels even after
a program or channel changes.
It also maintains natural flesh
tones while preserving fidelity
of background colors.
Use this function to adjust the
dark end (Cutoff) and bright end
(drive) of the White background.
Set the gray side bars On/Off
when watching 4:3 signals in
standard mode.
Choose the picture format
aspect ratio.
Choose to Reset Video Settings
to factory settings.
On-Screen Display
Video
41
On-Screen Display
Audio
Treble
Bass
Balance
Surround
Bass Boost
Audio Source
Internal Speakers
Auto Noise Cancel
Perfect Volume
Loudness
Language
Digital Output
DRC
Timers
Adjust the treble.
Adjust the bass.
Adjust the balance.
Select Surround settings (Off,
Wide, Normal)
Select Bass Boost option ON or OFF.
Select between three Audio
Sources.
Select internal or external
speakers.
Eliminates the noise between
stations.
Adjust volume in fixed setting.
Adjust Loudness.
Select Language options if
available.
Select Optical Output options.
Select Dynamic Range
Compression to ON or OFF.
NOTE: The Language, Digital Output, and the
Dynamic Range Compression feature of the
Audio OSD are only available for Digital
channels.
On-Screen Display
TV Guide On Screen
TV Guide On Screen
Set, Control and navigate the
system
Channel Manager
Signal Meter
Auto Channel Scan
Channel List
Access Signal Meter.
Set Auto Channel Scan.
Set Channel List.
Locks
Change Access Code Change Lock access code.
Engage Lock
Choose to lock channel,
and/or Side panel.
Movie Ratings
Block various types of movies
and video types based on
motion picture ratings.
TV Ratings
Block various types of movies
and television programming
based on a parental guide
ratings.
Canadian Ratings (ENG) Block various types of movies
and television programming
based on the Canadian ratings
system.
Canadian Ratings (FRN) Block various types of movies
and television programming
based on the Canadian French
ratings system.
Alternate Ratings U.S. Ratings system for DTV Signal
to block various types of programs
42
Set the Clock
Set Sleep Timer
Set Day/Night Timer
Set Clock Settings.
Set Sleep Timer intervals
(30 min. intervals, 00:30-3:00).
Set Day/Night picture mode
settings.
Setup
Set The Menu Options
Choose English, French, or
Spanish text and Background.
Automatic Power Saving
features.
Label Video Inputs, VCR, DVD,
etc.
Set The Power Saving
Set The Inputs
Set The Closed Captions
Feature to display dialogue/text.
Set The Output Terminals
CableCARD Information
Set Output source options.
Access important CableCARD
and Diagnostics info.
Set The Quick Start Options Select the TV Quick Start Up
options.
Reset The Software
Select to upgrade TV software.
Power Swivel
Unlocked
Power Swivel enabled. Control
the motorized Table Top Stand
Power Swivel disabled.
Locked
NOTE: 1. The Signal Meter feature of the Channel
Manager OSD is only available for Digital
channels.
2. The CableCARD information feature of the
Setup OSD is only available when a
CableCARD from your cable operator is
installed in the rear panel of the TV.
3. Power Swivel feature is only available when
Table Top Stand is connected.
Video
Video
Video
Audio
Select VIDEO to adjust picture settings and improve
picture quality. You can independently customize each of
the Video Inputs to your preference to increase viewing
performance and pleasure depending upon the video
program being viewed. If RESET is selected, only the
selected input will reset to initial conditions.
Picture Mode
Use this function to choose from automatic picture
settings to optimize your TV’s performance.
1. Use the CURSOR buttons or to highlight and
select PICTURE MODE settings (Day-Normal,
Day-Dynamic or Night).
2. Then press the SELECT button to set the mode and
return to the Video menu or press EXIT to quit menu.
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
SEL Select
Move
Video
OR
Air
Picture Mode
Day(Dynamic)
White Level
100%
Black Level
50%
Color
62%
Tint
Sharpness
50%
Motion Sharpness
Off
Back Light
50%
High
Color Temperature
3. There are 3 Picture Modes available for the customer
Day (Dynamic), Day (Normal) and Night mode.
Day (Dynamic) is the original factory preset mode , this
can be changed by adjusting any video setting to your
desire conditions. Day ( Normal ) can be used as a
second video setting for daytime viewing. Night is set
to watch programing during nigthtime.
Move
SEL Select
OR
On-Screen Display
OR
Picture Mode
Next/Prev
Day (Dynamic)
Select
SEL Return
1.
Use the CURSOR PAD or or CHANNEL WHEEL to highlight the function to be adjusted.
2.
Press the SELECT button or the CURSOR PAD to select the function settings.
3.
Press the CURSOR PAD or to adjust the function.
4.
Press MENU to return to main menu.
5.
Press EXIT to quit menu.
White Level
Use this function to change the white level in the picture.
Video
Audio
TV Guide On Screen
Black Level
Use this function to change the black level in the picture.
Channel Manager
Locks
Timers
Setup
Color
Use this function to adjust the level of color in the picture.
Power Swivel
Move
SEL Select
Tint
Use this function to adjust flesh tones so they appear
natural.
Sharpness
Use this function to adjust the amount of fine detail in the
picture.
Motion Sharpness
When moving picture occurs detail in the picture is lost
this function improves the picture detail in 3 modes Off,
Low and High.
Back Light
Use this function to change the back light of the LCD
panel, this will increase or decrease the brightness of
the LCD panel, but not the brightness of the video signal.
Video
OR
Air
Picture Mode
Day(Dynamic)
White Level
100%
Black Level
50%
Color
62%
Tint
Sharpness
50%
Motion Sharpness
Off
Back Light
50%
Color Temperature
Move
High
SEL Select
43
Video
Color Temperature
Set this to High for cooler color with more blue, set to Medium for more natural color, set to Standard for accurate
color or set to Black/White for more reddish color.
Black Enhancement
Use this function to enhance the shadow detail in dark scenes using the settings off, low, middle and high.
NOTE: 1. If WHITE LEVEL is selected, you are adjusting CONTRAST. The additional menu items BLACK LEVEL,
COLOR, TINT, and SHARPNESS can be selected and adjusted in the same manner.
2. It may be necessary to adjust TINT to obtain optimum picture quality when using the COMPONENT
VIDEO Y-PBPR input jacks.
3. CABLE and AIR share a Video setting. Also, each of the video inputs have their own independent
settings.
Contrast Mode
Use this function to choose between 2 Contrast Mode settings. Set to Dynamic for darker images more in the
level of Black, set to Normal for a balanced White to Black level.
Noise Reduction
The NOISE REDUCTION function automatically reduces conspicuous noise in the picture without degrading
picture quality. Set NOISE REDUCTION to OFF if the TV experiences picture blocking.
On-Screen Display
Auto Movie Mode
The AUTO MOVIE MODE function turn ON or OFF the 3:2 PULLDOWN DETECTION SPECIAL FEATURE.
Theatrical movies are shot on film at 24 frames or still pictures per second, instead of 30 frames or 60 fields like
video. When film is transferred to video for television viewing, the disparity between the two frame rates must be
reconciled. This involves a process known as 3:2 pulldown.
When AUTO MOVIE MODE is turned ON from the VIDEO menu, your Hitachi LCD Television will activate the
circuitry for this special feature to improve video performance when watching film based sources.
NOTE: 1.
2.
When using a Progressive Scan Component or HDMI Input (480p or 720p), AUTO MOVIE MODE
will not be available
All Video settings are independent of each other based on it’s input (Cable/Air, Input 1~5).
Color Management
Use this function to adjust and balance the listed individual colors to make them either deeper or more pure
depending on the user’s preference. Adjust the GAIN settings to make the color brighter (+) or darker (-). Adjust
the PHASE settings to make the colors deeper (+) or normal (-) to match real life colors.
1. Use CURSOR PAD or or CHANNEL WHEEL to
highlight the Color Management function.
2. Press the SELECT button or CURSOR PAD to select
Set User Colors setting. When the function has a “✓” in
the box called “Set User Colors”, it is ON.
Video
OR
Noise Reduction
Low
Auto Movie Mode
Off
Color Management
Color Decoding
Auto Color
Off
White Balance
Black Side Panel
3. Press the CURSOR PAD , , , and SELECT
button to highlight and adjust individual colors.
Reset Video Settings
Move
4. Use the CURSOR PAD and to highlight and select
“Reset” then press the SELECT button to return
all colors to default settings.
SEL Select
Video
or
NOTE: When the Set User Colors box is not
checked, the listed colors will be grayed out.
Off
Aspect
Color Management
Set User Colors
Magenta
Red
Yellow
Green
Cyan
Blue
Phase
±0
±0
±0
±0
±0
±0
Reset
Move
44
SEL Return
Gain
±0
±0
±0
±0
±0
±0
Gain
Phase
Video
Color Decoding
Use this function to adjust and balance the percentage of Red, Green and Color according to the user’s preference in
each of the four color temperature settings. Use TINT to adjust flesh tones so they appear natural.
1. Use CURSOR PAD or or CHANNEL WHEEL to
highlight functions.
2. Press the CURSOR PAD , , or and SELECT button
to highlight and adjust individual colors.
Video
Color Decoding
or
RGB
R
G
B
Red
50%
50%
Green
62%
Color
Tint
Reset
Move
SEL Return
NOTE: The Red and Green adjustments will apply for each color temperature.
Auto Color
The Auto Color function automatically monitors and adjusts the color to maintain constant color levels even after
a program or channel changes. It also maintains natural flesh tones while preserving fidelity of background colors.
NOTE: When receiving Antenna Digital Channel or using Component input , Auto Color will not be available (grayed out).
White Balance
Use the CUTOFF functions to adjust the color temperature of the dark areas of the picture.
Use the DRIVE functions to adjust the color temperature of the bright areas of the picture.
3. Press the EXIT button to quit or select White Balance to
return to the previous MENU.
Video
White Balance
On-Screen Display
1. Use the CURSOR PAD or or CHANNEL WHEEL
to highlight the choice.
2. Press the CURSOR PAD or to adjust.
or
Color Temperature
: High
Red Drive
Green Drive
Blue Drive
Red Cuto
Green Cuto
Blue Cuto
Reset
100%
100%
100%
50%
50%
50%
Move
SEL Return
Black Side Panel
The BLACK SIDE PANEL function turns the gray side
bars on/off when watching 4:3 signals in Standard
mode or use of the PIP modes.
1. Press the CURSOR PAD or to set to ON or OFF.
2. Press EXIT to quit menu or select BLACK SIDE
PANEL to return to the previous menu.
O
Black Side Panel
Next
On/Off
Black Side Panel
Next
SEL Return
On
On/Off
SEL Return
45
Video
Aspect
Use this function to select the Picture Format Aspect
Ratio.
Auto Aspect
Automatically adjust the Aspect Ratio depending on
the input signal to fill the screen.
Video
Aspect
OR
Auto Aspect
Mode
Vertical Position
Move
:
:
On
16:9 Standard1
0
SEL Return
Mode
M anually select the Aspect Ratio.
Vertical Position
This function allows you to select when aspect style is
either 4:3 EXPANDED/ZOOM1/ZOOM2 or 16:9
ZOOM. Vertical position can be changed with these modes. For example, it will be useful for centering the
picture area at both the top and bottom of the picture with 480i/480p signal. Adjustable range is -10 (video
center is toward bottom of screen) to +10 (video is toward top of screen).
1. Use the CURSOR PAD or to to select menu item.
2.
Press the CURSOR PAD or to adjust the function.
3.
Press the EXIT to quit the MENU, or select ASPECT to return to the main menu.
NOTE: Vertical Position will not be available in 4:3 Standard and 16:9 Standard modes.
On-Screen Display
Reset Video Settings
This function allows you to Reset the Video Menu Settings of the present input and return it to the Day-Dynamic
VIDEO mode.
Video
1.
2.
3.
4.
Use CURSOR PAD , or CHANNEL WHEEL
buttons to highlight functions.
Press the SELECT button or CURSOR PAD to
select Reset Video Settings.
Use the CURSOR PAD to access at the Reset
softkey.
Press the SELECT button to Reset the Video
Settings.
You can customize each of the Video Inputs to your
preference to increase viewing performance and
pleasure, depending upon the video program being
viewed. If RESET is selected, only the selected Input will
reset to the initial conditions as explained above.
If RESET is selected in Input 1, only Input 1 will return to
factory conditions.
46
OR
Noise Reduction
Low
Auto Movie Mode
O
Color Management
Color Decoding
Auto Color
O
White Balance
Aspect
Black Side Panel
O
Reset Video Settings
Move
SEL Select
Video
Reset Video Settings
OR
Select “Reset” to return the video menu settings
on this Input to the original factory settings.
Reset
Move
SEL Return
Audio
Audio
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Select AUDIO to adjust the TV to your preference and
to improve the sound quality.
Timers
Setup
Power Swivel
1.
2.
3.
Move
Press CURSOR PAD or to select menu item.
Press CURSOR PAD or to adjust the function.
Press EXIT to quit the MENU, or select AUDIO to
return to the main menu.
NOTE:
If TREBLE is selected you are adjusting
treble. The additional menu items Bass
and Balance can be selected and
adjusted in the same manner.
SEL Select
Audio
OR
Treble
50%
Bass
50%
L
Balance
Surround
Off
Bass Boost
On
Audio Source
Stereo
Internal Speakers
On
Auto Noise Cancel
Off
Perfect Volume
Off
Move
R
SEL Return
Treble
This function controls the high frequency audio to all speakers.
Bass
This function controls the low frequency audio to all speakers.
Balance
This function will control the left to right balance of the LCD TV internal speakers.
On-Screen Display
Surround
Surround sound is the concept of expanding the spatial imaging of audio from one dimension ( Mono/Left-Right)
to two or three dimensions. This is often done to create a more realistic audio environment.
1.- Use cursor or to highlight surround option.
2.- Use cursor or to select Off, Normal or Wide.
Off : turns off the surround sound effect.
Normal Surround : Provides the surround effect by locating two or more speakers to the rear of the listener.
Wide Surround : Reproduce much better quality 5 channel sound signals from ordinary stereo contents comparing with
normal surround technology. Wide surround enable users to enjoy sound playback in wide surround virtual area like
5 channel contents with ordinary stereo contents.
Bass Boost
This function allows to enhance the low frequency audio performance of your speaker system.
47
Audio
Audio Source
Multi-Channel Television Sound will allow you to select STEREO (a stereo broadcast), MONO (monaural sound)
used when receiving a weak stereo broadcast or SECOND AUDIO PROG (SAP) which may be a secondary
language, weather report, etc.
Internal Speakers
This function is useful when setting up the external speakers.
ON
TV as Center
OFF
Select this feature if using the internal speakers only.
Select this feature when setting up external speakers from a separate stereo system. The
TV’s speakers will work as the center speaker.
Select this feature if you prefer to use only speakers from a separate stereo system.
Auto Noise Cancel
This function eliminates the noise between stations. If a channel is tuned and is noisy, this function will
automatically eliminate the audio for that channel.
Perfect Volume
This function will automatically adjust volume so each channel and input has the same average volume level.
Loudness
Set this function to ON to emphasize bass and treble at low volume levels.
Language
Some programs transmit more than one DTV language option. Most will have English as a default language. The
language function will allow you to select up to 4 language options (if available).
Digital Output
This function allows you to select between Dolby® Digital and PCM.
On-Screen Display
Dolby® Digital - Select this feature if the TV is connected to an amplifier/receiver with a Dolby® Digital only
decoder; it will provide six independent soundtrack channels through the optical output jack (Digital Audio).
NOTE:
*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
PCM - Select this feature if the TV is connected to an amplifier/receiver with a PCM only decoder; it will provide
two independent soundtrack channels through the optical output jack (Digital Audio).
DRC
Dynamic Range Compression - Use this function to
compress the range of sound volume. By compressing
the range of sound volume, it is possible not only to
suppress the output of loud sound at night but also to
raise the volume of low sound. The default setting is ON.
Use the CURSOR PAD or to select the chosen
options.
Audio
OR
Treble
%
0
5
ass
B
%
0
5
L
alance
B
Surround
Off
Bass Boost
On
Audio Source
Stereo
Internal Speakers
On
Auto Noise Cancel
Off
Perfect Volume
Off
SEL Return
Move
NOTE: The functions Language, Digital Output and DRC
are only available when viewing digital programs.
Use the functions at right if your TV is connected to an
amplifier/receiver with optical digital input with Dolby
Digital or PCM decoder capabilities.
NOTE: 1.- The DRC control affects only Dolby Digital
signals decoded internally by the TV.
2.- DRC does not affect the Dolby Digital bitstream
available at the digital audio output.
48
Audio
Bass Boost
On
Audio Source
Stereo
Internal Sp
eakers
n
O
Auto N
oise Cancel
f f
O
Perfect Volum
e
f f
O
Loudness
f f
O
Language
1 [U
nknow
n]
Digital u
Otp
ut
DolbyDigital
n
O
DRC
Move
SEL Return
R
TV Guide On Screen
TV Guide On Screen
The TV Guide On-Screen system is a built-in feature
that provides a channel lineup and program listings in
your area. Once the setup process is complete, the
program listings are automatically updated several
times a day.
Screen 2: Enter the zip code (USA) or postal code
(Canada):
Use the Numeric buttons and the CURSOR PAD and for letter entries to enter the ZIP code (USA)
or postal code (CANADA) of your location.
If using a VCR, you must first setup the
LCD TV as shown on Page 22.
To Setup the TV Guide On Screen System:
1.
Press the MENU button. Use the CURSOR PAD to highlight TV GUIDE ON SCREEN, then press the
SELECT button.
Video
*For USA is a 5 digit ZIP CODE
**For CANADA is a 6 digit ZIP CODE
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
Setup
Power Swivel
Move
2.
On-Screen Display
Note:
SEL Select
Screen 3:
Please select which service(s) you would like your
TV Guide On ScreenTM to support (Check all that
appl y):
Use the CURSOR PAD and to highlight your
choice, then press the SELECT button then select
Next :
Pressing the GUIDE button also allows you
immediate access to this feature.
Press the SELECT button to continue.
Setup Procedure:
Screen 1: Select which country your TV is located in:
Use the CURSOR PAD and to highlight your
TV location (USA or CANADA), then press the
SELECT button to continue.
Screen 4:
Are the above settings correct ?
Use the CURSOR PAD and to highlight your
choice, then press the SELECT button then select
Next :
*If all setting are correct please select Yes to continue.
*If a setting is wrong please select No to modify.
49
TV Guide On Screen
Screen 5:
Would you like to use the TV Guide On Screen
system to control recording with your VCR?
Use the CURSOR PAD and to highlight your
choice, then press the SELECT button then next.
If YES: Please see Screen 6.
If NO: Please see Screen 12.
On-Screen Display
Screen 6:
The screen will show the correct way to setup
the VCR with the G-Link. Please confirm the
connections (see page 22). Press SELECT
button to continue.
Screen 7:
What brand of VCR is connected to this TV ?
Use the CURSOR PAD and to
highlight your choice, then press the SELECT
button to continue.
50
Screen 8:
This screen shows the stept that you need to follow
to make the correct setup of your VCR with the G-LINK.
Please check your connection (see Page 22). Press the
SELECT button to continue.
Screen 9:
Now the TV GUIDE will send the code to control the
VCR through the G-Link connection.
Screen 10:
Did your VCR stop playback of the TAPE ?
If Yes then go to screen 11
If No the TV Guide will try a different code and return to
screen 9.
If you like to Test this test code again one more time
TV Guide On Screen
Screen 11:
Are the settings correct ?
If Yes the TV Guide setup is complete, then press
SELECT button to continue.
If No please make the necessary changes in order
to complete the TV Guide setup procedure.
Screen 14:
None of the Hitachi codes appeared to control your
VCR. What would you like to do now ?
1.- Try VCR configuration again to repeat the setup.
2.- Try alternate remote codes to see other code
alternatives that may solve the problem.
3.- Skip this step , will finish the TV Guide setup ;
but will show an incomplete setup for your VCR.
Screen 12:
This shows that the setup procedure is complete
Use the CURSOR PAD and to highlight Next
or if you are like to make changes select Back ;
Then press SELECT button to continue or finish.
On-Screen Display
Screen 13:
When a CODE for a VCR is not accepted then
the following message will appear. Check the
setup as mentioned then select Next.
NOTE: 1. The LCD TV should be in standby mode
in order to continually receive updated
program listings from your cable company.
2. If using a Cable box, please leave it ON to
continually receive updated program
listings from your cable company.
For using and navigating the TV Guide On Screen System please refer to the TV Guide Instruction Book.
51
Channel Manager
Channel Manager
Video
Audio
TV Guide On Screen
Channel Manager
Select CHANNEL MANAGER to set your Antenna
options, run Auto Channel Scan, Check Signal Meter
and Set Channel List.
Locks
Timers
Setup
Power Swivel
1.
Press CURSOR PAD , or CHANNEL WHEEL
buttons to highlight function.
2.
Press the SELECT button or CURSOR PAD to
select.
Move
SEL Select
Channel Manager
Signal Meter
OR
Auto Channel Scan
Channel List
Move
Signal Meter
Select SIGNAL METER when using an indoor or outdoor
antenna. This feature will show the signal strength and
peak values of the Antenna signal to help you adjust your
antenna to optimize signal reception.
SEL Select
Channel Manager
Signal Meter
OR
Auto Channel Scan
Channel List
Move
SEL Select
On-Screen Display
Use the CURSOR PADS and the SELECT button to
highlight and select CLOSE to exit.
NOTE: The Signal Meter will not be available (grayed
out) when watching analog channels.
Channel Manager
Signal Meter
-3 1
91
91
10
Channel
Strength
Peak
SNR
Close
Move
Auto Channel Scan
This feature will automatically store active Analog and
Digital channels in Auto Channel Scan memory.
1.
Use the CURSOR buttons or to highlight
AIR, CABLE (1) or CABLE(2) source.
2.
Press the CURSOR buttons or to highlight the
START or RESET option.
3.
Press the SELECT button to select.
SEL Return
Channel Manager
Signal Meter
Auto Channel Scan
Channel List
Move
SEL Select
Channel Manager
NOTE: 1.
2.
52
When a CableCARD is installed, Auto
Channel Scan will not be available since
channels will be fixed based on what was
agreed upon by you and your cable
operator.
If certain channels are poor or not possible
in cable(1) mode, set cable source to cable(2)
by using the CURSOR buttons or .
Auto Channel Sc an
OR
Air
Source
Auto Channel Sc an
Move
SEL Return
Start
Reset
Channel Manager
Channel List
This function allows you to review which channels are
labeled (CH ID), which have been added to CHANNEL
MEMORY (SCAN), which are protected by LOCK and
which are your FAVORITE (FAV) CHANNELS.
1.
Use the CURSOR PAD to navigate the Channel List.
2.
Press the SELECT button to select ON or OFF on the
SCAN and LOCK columns.
Channel Manager
Signal Meter
Auto Channel Scan
Channel List
Move
SEL Return
Channel Manager
3.
To select LOCK column, input the access code.
(Default access code: 0000)
4.
Press the CHANNEL WHEEL button to set or remove
the FAVORITE channel settings.
5.
Press the EXIT button to return to normal viewing.
NOTE: 1.
2.
OR
Channel List
FAV
CH
#
-1
3
4
5
6
7
8
9
10
o Ino
N
f.
Move
Scan
O
n
n
O
n
O
n
O
n
O
n
O
n
O
n
O
Lock
O
O
O
O
O
O
O
O
Return
FO
IN
ID
--------------------------------------------------:-- AM--:-- AM
Detail
When a CableCARD is installed, the Channel List will be dependent on channels agreed
upon by you and your cable operator.
The Channel List cannot be updated by only changing the cable source. Auto Channel Scan must
be performed for the Channel List to be updated.
On-Screen Display
53
Locks
Locks
Video
Audio
TV Guide On Screen
This function will block out the picture and sound of the
selected channel or video input.
Channel Manager
Locks
Timers
Setup
Power Swivel
Move
SEL Select
The code to enter the Locks feature is a four digit
access code number. The factory preset code is 0000.
Use the NUMBER buttons to enter the access code.
1.
Use the CURSOR PAD , or CHANNEL
WHEEL buttons to highlight the desired function
in the LOCKS menu.
OR
Please Enter Access Code
Access Code: - - - eys]Enter Code
[#K
2.
Press the SELECT button to select.
Change Access Code
1. To change the ACCESS CODE NUMBER, select
CHANGE ACCESS CODE to change the factory
preset code (0000) to your preference.
0
Locks
Change Access Code
0
If you forget your ACCESS CODE NUMBER, use
the factory code 7777 to erase your key number.
This will reset the access code number back to the
factory preset (0000).
0
0
Engage Lock
Movie Ratings
TV Ratings
Canadian Ratings(Eng)
Canadian Ratings(Frn)
Alternate Ratings U.S.
On-Screen Display
Move
2.
Enter a new four digit number.
3.
Press EXIT to quit the menu.
SEL Select
Engage Lock
When ENGAGE LOCK is selected, SET CHANNEL LOCK and SET FRONT PANEL LOCK can be set individually.
When SET CHANNEL LOCK is turned on, the picture and sound for the chosen channel will be blocked out.
When FRONT PANEL LOCK is turned on, all buttons on the Front Panel will be deactivated, except the
POWER button.
When MOVIE RATINGS is selected, you can block various types of movies and video tapes based on motion
picture ratings. Picture-in-Picture will also be blocked automatically (see page 55).
When TV RATINGS is selected, various types of television programming based on a parental guide ratings will be
blocked. Picture-in-Picture will also be blocked automatically (see page 56).
Use CANADIAN RATINGS to block various types of movies and television programs based on the two rating
systems used in Canada that you feel may be inappropriate due to its content (see pages 57-58).
Use ALTERNATE RATINGS (U.S.) to block various types of movies and television pograms based on ratings
systems used in U.S. that you feel may be inappropriate due to its content (see page 59).
NOTE:
54
The ALTERNATE RATINGS (U.S.) option is available for Digital Channels only.
Locks
Movie Ratings
Use Movie Ratings to prevent viewing of any movie that
you feel may be inappropriate due to its content.
Locks
Change Access Code
Engage Lock
Movie Ratings
1.
2.
TV Ratings
Use the CURSOR PAD , or CHANNEL WHEEL
buttons to select the MOVIE RATING category that
you want to block.
Canadian Ratings(Eng)
Canadian Ratings(Frn)
Alternate Ratings U.S.
Move
Press SELECT to block the MOVIE RATING that you
have selected. Once rating is selected, for example
PG-13, all movies rated PG-13 and higher (R, NC-17,
and X) will be blocked.
SEL Select
Locks
Movie Ratings
OR
3.
Press EXIT to quit the menu or select MOVIE
RATING to return to the previous menu.
S ta tu s
N o t R a te d
G
PG
PG-13
R
C
N-17
X
Move
SEL Return
On-Screen Display
Motion Picture Ratings Table
NOT RATED
Contains no rating. Not Rated (NR) and Not Applicable (NA) programs. Movie has not
been rated or ratings do not apply.
G
General audiences. All ages admitted.
PG
Parental guidance suggested. Some material may not be suitable for children.
PG-13
Parents strongly cautioned. Some material may be inappropriate for children under 13.
R
Restricted. Under 17 requires accompanying parent or adult guardian.
NC-17
No one 17 and under admitted.
X
Adults only
NOTE: 1. A movie rating is dependent upon the movie that is viewed. If the movie does not carry a rating, the
TV will not block it.
2. Blocking NOT RATED programs may block emergency programming, sports, news, public service
announcements, religious programs and weather.
3. If a CableCARD is installed, your cable operator may provide an Emergency Alert System (EAS)
message in the event of a local or national emergency with the purpose of alerting the general
public. When you receive such messages, the Television will immediately tune to an EAS channel as
directed by the EAS message. Please be advised that if the EAS channel is blocked using the
LOCKS feature, you will not be able to tune to that channel.
55
Locks
TV Ratings
Use TV RATINGS to prevent the viewing of any TV
program that you feel may be inappropriate due to its
content.
Locks
Change Access Code
Engage Lock
Movie Ratings
TV Ratings
1.
2.
Canadian Ratings(Eng)
Use the CURSOR PAD , or CHANNEL WHEEL
buttons to select the TV RATING category that you
want to block.
Canadian Ratings(Frn)
Alternate Ratings U.S.
Move
SEL Select
Press SELECT to block the TV RATING that you
have selected.
Locks
TV Ratings
3.
Press EXIT to quit the menu or select TV RATING
to return to the previous menu.
OR
Status
T V- Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
Move
D
S u b R a ti n g
L
S
V
FV
SEL Return
On-Screen Display
TV Parental Guide Ratings Table
TV-Y
All children. The themes and elements in this program are specifically designed for a very
young audience, including children from ages 2-6.
TV-Y7
Directed to older children. Themes and elements in this program may include mild
physical or comedic violence, or may frighten children under the age of 7.
TV-G
General audience. It contains little or no violence, no strong language, and little or no
sexual dialogue or situations.
TV-PG
Parental guidance suggested. The program may contain infrequent coarse language,
limited violence, some suggestive sexual dialogue and situations.
TV-14
Parents strongly cautioned. This program may contain sophisticated themes, intense
sexual situation, more intense violence and intensely suggestive dialogue.
TV-MA
Mature audiences only. This program may contain mature themes, indecent language,
graphic violence, and explicit sexual content.
FV
Fantasy Violence
V
Violence
S
Sexual Situation
L
Adult Language
D
Sexually Suggestive Dialogue
NOTE: 1. If you Block TV-14D, you will still permit TV-MA programs; If you block TV-14V, you will
automatically block TV-MAV programs, but you will still permit TV-MALS programs. This means that
the TV will block violence in TV-14 and higher (TV-MA), but not language and sex.
2. TV program ratings are dependent on the broadcaster. If the program is not rated, the TV will not
block it.
3. If a CableCARD is installed, your cable operator may provide an Emergency Alert System (EAS)
message in the event of a local or national emergency with the purpose of alerting the general
public. When you receive such messages, the Television will immediately tune to an EAS channel as
directed by the EAS message. Please be advised that if the EAS channel is blocked using the
LOCKS feature, you will not be able to tune to that channel.
56
Locks
Canadian Ratings (Eng)
Use CANADIAN RATINGS (ENG) to block any type of
movie and television program in Canada that you feel
might be inappropriate in its content.
Locks
Change Access Code
Engage Lock
Movie Ratings
TV Ratings
1.
2.
3.
Canadian Ratings(Eng)
Use the CURSOR PAD , or CHANNEL WHEEL
buttons to select the CANADIAN RATINGS
(ENG) category that you want to block.
Press SELECT to block the CANADIAN RATINGS
(ENG) that you have selected. Once rating is
selected, for example C8+, all movies and
television programs rated C8+ and higher (G, PG,
14+ and 18+) will be blocked automatically.
Press EXIT to quit the menu or select CANADIAN
RATINGS (ENG) to return to the previous menu.
Canadian Ratings(Frn)
Alternate Ratings U.S.
Move
SEL Select
Locks
Canadian Ratings(Eng)
OR
S ta tu s
C
C8+
G
PG
14+
18+
Move
SEL Return
On-Screen Display
Canadian Ratings English Table
C
Programming intended for children under age 8 - Violence Guidelines; Careful attention is
paid to themes, which could threaten children’s sense of security and well-being. There will
be no realistic scenes of violence. Depictions of aggressive behaviour will be infrequent
and limited to portrayals that are clearly imaginary, comedic or unrealistic in nature. Other
Content Guidelines: There will be no offensive language, nudity or sexual content.
C8+
Programming generally considered acceptable for children 8 years and over to watch on
their own - Violence Guidelines: Violence will not be portrayed as the preferred, acceptable,
or only way to resolve conflict; or encourage children to imitate dangerous acts which they
may see on television. Any realistic depictions of violence will be infrequent, discreet, of
low intensity and will show the consequences of the acts. Other Content Guidelines: There
will be no profanity, nudity or sexual content.
G
General Audience - Violence Guidelines: Will contain very little violence, either physical or
verbal or emotional. Will be sensitive to themes which could frighten a younger child, will
not depict realistic scenes of violence which minimize or gloss over the effects of violent
acts. Other Content Guidelines: There may be some inoffensive slang, no profanity and
no nudity.
PG
Parental Guidance - Programming intended for a general audience but which may not be
suitable for younger children. Parents may consider some content inappropriate for
unsupervised viewing by children ages 8-13. Violence Guidelines: Depictions of conflict
and/or aggression will be limited and moderate; may include physical, fantasy, or
supernatural violence. Other Content Guidelines: May contain infrequent mild profanity, or
mildly suggestive language. Could also contain brief scenes of nudity.
14+
Programming contains themes or content which may not be suitable for viewers under the
age of 14 - Parents are strongly cautioned to exercise discretion in permitting viewing by
pre-teens and early teens. Violence Guidelines: May contain intense scenes of violence.
Could deal with mature themes and societal issues in a realistic fashion. Other Content
Guidelines: May contain scenes of nudity and/or sexual activity. There could be frequent
use of profanity.
18+
Adult - Violence Guidelines: May contain violence integral to the development of the plot,
character or theme, intended for adult audiences. Other Content Guidelines: May contain
graphic language and explicit portrayals of nudity and/or sex.
57
Locks
Canadian Ratings (Frn)
Use CANADIAN RATINGS (FRN) to block Canadian
French programs according to various program ratings
that you feel might be inappropriate in its content.
Locks
Change Access Code
Engage Lock
Movie Ratings
TV Ratings
1.
2.
3.
Canadian Ratings(Eng)
Use the CURSOR PAD , or CHANNEL WHEEL
buttons to select the CANADIAN RATINGS
(FRN) category that you want to block.
Press SELECT to block the CANADIAN RATINGS
(FRN) that you have selected. Once rating is
selected, for example 8 ANS+, all movies and
television programs rated 8 ANS+ and higher will
be blocked automatically.
Press EXIT to quit the menu or select CANADIAN
RATINGS (FRN) to return to the previous menu.
Canadian Ratings(Frn)
Alternate Ratings U.S.
Move
SEL Select
Locks
Canadian Ratings(Frn)
OR
S ta tu s
G
8 ans +
13 ans +
16 ans +
18 ans +
Move
SEL Return
On-Screen Display
Canadian Ratings French Chart
G
General - Programming intended for audiences of all ages. Contains no violence, or the
violence content is minimal or is depicted appropriately with humor or caricature or in an
unrealistic manner.
8 ans +
8 + General - Not recommended for young children - Programming intended for a broad
audience but contains light or occasional violence that could disturb young children.
Viewing with an adult is therefore recommended for young children (under the age of 8)
who cannot differentiate between real and imaginary portrayals.
13 ans +
Programming may not be suitable for children under the age of 13 - Contains either a few
violent scenes or one or more sufficiently violent scenes to affect them. Viewing with an
adult is therefore strongly recommended for children under 13.
16 ans +
Programming is not suitable for children under the age of 16 - Contains frequent scenes of
violence or intense violence.
18 ans +
Programming restricted to adults - Contains constant violence or scenes of extreme
violence.
58
Locks
Alternate Ratings U.S.
Use Alternate Ratings to prevent viewing of any movie or
program that you feel may be inappropriate due to its content.
This feature will be available only for ATSC Digital signal.
In case only NTSC analog signal is received this feature will
be unavailable (grayed out).
In order to set the Alternate Ratings the ATSC Digital channel
received must include Alternate Ratings data .To see
if the channel has Alternate Ratings , press the INFO key
on the R/C. See fig. (1) for reference.
Once the TV has received Alternate Ratings data , the
Alternate Ratings US in the lock menu will become
available.
Program Title
Program Title. . . . . . . .
11:30AM
11:55AM ALT U.S.
Multi
DTVCC
CF-18 ans+
Receiving
Audio Language
(Digital CH)
/Receiving BTSC
(Analo g CH )
Source
Program Time
INFO
Cable 888-001
KDEF-DT
1080i
10:35 AM
CH ID/Input ID
Current Time
Receiving
Signal o
F rmat
Receiving
Digital Closed Caption
Receiving
Rating Broadcast
Alternate Ratings
A u to
11: 30 A M
Closed Caption Mode
Event Timer
G-Guide Model
Fig. (1)
Locks
Change Access Code
Engage Lock
Movie Ratings
TV Ratings
1.
Use the CURSOR buttons or
to select the
ALTERNATE RATING category that you want to block.
Canadian Ratings(Eng)
Canadian Ratings(Frn)
Alternate Ratings U.S.
Move
SEL Select
Locks
Alternate Ratings U.S.
CATEGORY NAME (1 / 10)
Status
OR
TV-Y
:
:
:
ABCDEFJH :[
On-Screen Display
TV-Y7
12345678
2.
Press SELECT to block the ALTERNATE RATING
that you have selected. Once rating is selected, for
example PG-13, all movies rated PG-13 and higher
(R, NC-17 and X) will be blocked.
Move
Press EXIT to quit the menu or select ALTERNATE
RATINGS to return to the previous menu.
SEL View
Block
Locks
Alternate Ratings U.S.
OR
3.
]
CATEGORY NAME (1 / 10)
Status
TV-Y
:
TV-Y7
:
:
12345678
ABCDEFJH :[
]
Directed to older children. Themes and elements in
this program may include mild physical or comedic
violence, or may frighten children under the age of 7.
Move
SEL View
Block
Alternate Ratings (Example Only) :
G
PG
PG-13
R
NC-17
X
Y
General audiences. All ages admitted.
Parental guidance suggested. Some material may not be suitable for children.
Parents strongly cautioned. Some material may be inappropriate for children under 13.
Restricted. Under 17 requires accompanying parent or adult guardian.
No one 17 and under admitted.
Adults only
Adults only
NOTE: In some cases the OSD will show the function name as " Alternate Ratings U.S. " or "Downloaded
Ratings " , in both cases the operation is the same only name is different.
59
Timers
Timers
Video
Audio
TV Guide On Screen
Select TIMERS to set your Clock, Sleep Timer and
Day/Night Timer.
1.
2.
Channel Manager
Locks
Timers
Setup
Use the CURSOR buttons or or CHANNEL
WHEEL to highlight the function to be adjusted.
Power Swivel
Mov e
SEL Select
Press the SELECT button to select.
Timers
OR
Set The Clock
-- : -- AM PST
Set Sleep Timer
0:00
Set Day/Night Timer
Not Set
Move
On-Screen Display
Set The Clock
The Clock must be adjusted before you can use the
DAY/NIGHT TIMER feature.
1.
Use the CURSOR PAD , , , or CHANNEL
WHEEL buttons to highlight the chosen TIME
ZONE settings.
2.
Press the SELECT button to select. If you observe
daylight savings, use CURSOR PAD to highlight
DAYLIGHT SAVING CORRECTION and press the
SELECT button to select.
Timers
Use the CURSOR PAD , , , or CHANNEL
WHEEL buttons to highlight the CURRENT TIME
hour and minute), AM or PM, MONTH, DAY, and YEAR.
Set The Clock
-- : -- AM PST
Set Sleep Timer
0:00
Set Day/Night Timer
Not Set
Move
SEL Select
Timers
Set The Clock
OR
3.
SEL Return
Time Zone
Date
Time
:
:
:
PST
Jan. 1 2005
-- : -- AM
Automatically adjust clock
for daylight savings changes.
Move
SEL Return
4.
Use the CURSOR PAD , to adjust settings.
5.
Press the SELECT button to set the TIME AND DATE.
6.
Press EXIT to quit the menu or select SET THE CLOCK to return to the previous menu.
When AUTOMATICALLY ADJUST CLOCK FOR DAYLIGHT SAVING CHANGES is checked ■
✔, the
TV will automatically calculate the clock adjustment for Daylight Saving.
2. When the CableCARD is used, the TV will SET THE CLOCK automatically and also when the TV Guide
On Screen system setup process is complete. In this case the Set The Clock feature will not be
available (grayed out).
3. The TV counts electrical pulses for regulating the TIMERS. When the power cord is unplugged then
plugged in quickly, the clock is stopped momentarily and the TIME indication will become slow.
NOTE: 1.
60
Timers
Set Sleep Timer
Select this feature to set your SLEEP TIMER from 30
minutes to 3 hours (30 minute increments).
Timers
Set The Clock
-- : -- AM PST
Set Sleep Timer
0:00
Set Day/Night Timer
1.
Press the CURSOR PAD repeatedly to set your
Timer from 0:00, 0:30, 1:00, 1:30, 2:00, 2:30 and
3:00.
Move
Not Set
SEL Select
Timers
Set The Clock
-- : -- AM PST
Set Sleep Timer
0:00
Set Day/Night Timer
Move
Set Day/Night Timer
Select this feature to activate and set your TV’s
DAY/NIGHT PICTURE MODE automatically. This
feature is not available until the clock is set.
Set The Clock
2.
Press the SELECT button to select.
3.
Use the CURSOR PADS to select DAY MODE ON
and to set it’s TIMER.
-- : -- PST
Set Sleep Timer
0:00
Set Day/Night Timer
Not Set
SEL Select
On-Screen Display
Use the CURSOR PADS to highlight SET
DAY/NIGHT TIMER settings.
SEL Set
Timers
Move
1.
Not Set
Timers
Set Day/Night Timer
4.
Use the CURSOR PADS to select DAY MODE OFF
and to set it’s TIMER.
5.
Press EXIT to quit the menu or select SET
DAY/NIGHT TIMER to return to the previous
menu.
OR
Activate
Day Mode On :
Day Mode Off :
Move
06:00 AM
06:00 PM
SEL Return
61
Setup
Setup
Video
Audio
TV Guide On Screen
Select SETUP when setting your TV up for the first
time.
Channel Manager
Locks
Timers
1.
2.
Setup
Use the CURSOR PAD , , or to select the
sub-menu of your choice.
Power Swivel
Move
SEL Select
Press the SELECT button to select.
Setup
Set The Menu Options
OR
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
Set The Quick Start Options
Reset The Software
Move
Set The Menu Options
Setup the Language and background of the Menu
OSD.
SEL Select
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
On-Screen Display
Set The Language
This feature will allow you to select any one of three
different languages for all on-screen displays.
1.
Setup
Power Swivel
Move
SEL Select
Use the CURSOR PAD or to select the
language of your choice.
Setup
2.
Press EXIT to quit menu or select SET THE MENU
OPTIONS to return to previous menu.
Set The Menu Options
OR
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
Set The Quick Start Options
Reset The Software
Move
SEL Select
Setup
Set The Menu Options
OR
Set The Language
Set The Menu Background
Move
62
SEL Return
:
:
English
Shaded
Setup
Set the Menu Background
This function allows you to choose from two menu
backgrounds.
1.
Setup
Menu Preference
Set The Language
Set The Menu Background
Use the CURSOR PAD or to highlight
SET THE MENU BACKGROUND (SHADED
OR SOLID) of your choice. Use the CURSOR
PAD or to select shaded or solid.
Move
:
:
English
Shaded
SEL Return
2.
Select SOLID for a black background (no
picture can be seen behind menu screen),
select SHADED and a light background is
visible.
3.
Press EXIT to quit menu or select MENU PREFERENCE to return to previous menu.
Set The Power Saving
This features help to increase the Lamp life.
Setup
Set The Menu Options
Set The Power Saving
OR
Set The Inputs
Image Power
Use this feature to have the TV save energy
by changing the back light level in three modes:
Max,Med and Min.
1.
Automatic Power Saving
Use this feature to have the TV turned OFF
automatically when a video signal is not detected for
about 12 seconds.
1.
Press the CURSOR buttons or to highlight
Yes or No.
Set The Output Terminals
CableCARD Information
Set The Quick Start Options
Reset The Software
Move
SEL Select
On-Screen Display
Press the CURSOR buttons or to select the
modes Max, Med or Min.
Set The Closed Captions
Setup
Set The Power Saving
Image Power
:
Max
Automatic Power Saving
Yes
Move
No
SEL Return
NOTE: Your new HDTV has a built-in Automatic Power Saving feature that shuts Off the TV if a video signal is not
detected within 12 seconds. The default setting for this feature is ON (Yes). The Automatic Power Saving
feature needs to be set to OFF (No) before any CableCARD set up can be performed.
INSTRUCTIONS:
1. Access the Menu OSD by press the MENU button of the remote control.
2. Navigate the menu to access SETUP, then SET THE POWER SAVING. SET AUTO POWER
SAVING OFF (No) using the Cursor and the SELECT buttons of the remote control.
3. Use the Cursor buttons to highlight “No” then press the SELECT button to set this feature to Off.
4. After CableCARD set up is completed, set the Auto Power Saving feature to ON (Yes).
63
Setup
Set The Inputs
Use this feature to give a name to any of the five video
inputs.
Setup
Set The Menu Options
OR
Set The Power Saving
1.
Press the CURSOR PAD or to highlight the
video inputs.
Set The Inputs
2.
Press the CURSOR PAD or to select your
choices.
Set The Quick Start Options
Set The Closed Captions
Set The Output Terminals
Reset The Software
Move
SEL Select
Note: The inputs labeled Gray out (Skip) or Hide
(Skip) are disabled in the INPUTS selection.
INPUT 4 Auto Link
Use this function to automatically turn the TV on and
tune to INPUT 4 when it detects a video signal to
INPUT 4.
1.
Use the CURSOR PAD , , or to
highlight and select the AUTO LINK setting of
your choice.
Setup
Set The Inputs
Input1 :
Input2 :
Input3 :
Input4 :
Auto Link : Off
Input5 :
*
*
*
*
*
Move
SEL Return
- Auto
When AUTO is selected, the TV will turn on
and switch to INPUT 4 automatically, when the
INPUT 4 input device is turned on. This is
convenient when you want to watch a movie with your VCR, laserdisc player or DVD player.
- Remote
When REMOTE is selected, the TV will turn on and switch to INPUT 4 automatically when the INPUT 4
input device is turned on and the VCR, laserdisc, or DVD play button on your remote control is pressed.
This is convenient when you want to record a movie with your VCR and watch it later.
On-Screen Display
- Off
Select OFF to disable this function.
2.
Press EXIT to quit menu or select SET THE INPUTS to return to previous menu.
NOTE: 1. Once the TV has been turned on using the AUTO LINK feature, it must be reset before AUTO LINK
is used again. To do this, turn your VCR, laserdisc, or DVD player OFF. This feature is now reset and
will turn on your TV as described above.
2. When using REMOTE mode, any remote control button will substitute for your video input device
play button. However, intended operation is for use with your VCR, laserdisc, or DVD play button.
3. If no remote control button is pressed after the TV is turned on by AUTO LINK, the TV will
automatically turn off after three hours.
Set AV NET
64
Setup
Set The Closed Captions
Closed Captions are the dialogue, narration, and/or
sound effects of a television program or home video
which are displayed on the TV screen. Your local TV
program guide denotes these programs as
or
.
Setup
Set The Menu Options
OR
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
Set The Quick Start Options
1.
2.
Use the CURSOR PAD , , and to highlight
and select the function to change.
Reset The Software
SEL Select
Move
Press EXIT to quit menu or select SET THE
CLOSED CAPTIONS to return to the previous menu.
Caption Display:
ON/OFF will turn the
display on or off.
AUTO will turn the
display on when
Mute/Soft Mute is on.
Analog Captions:
Set CAPTIONS for Analog programs. This
function will help choose and set available
mode and channel.
Setup
Set The Closed Captions
OR
:
Caption Display
:
Off
Analog
Mode
Channel
:
:
Captions
1
Digital
Language
Font
Size
Style
:
1(Unknown)
Default
Standard
Standard
Hitachi
Move
:
:
:
SEL Return
Caption Mode:
CAPTIONS is for the program you are viewing.
TEXT is for additional information such as news reports or a TV program guide. This information covers
the entire screen and viewing the TV program is not possible. Text may not be available with every
program.
On-Screen Display
Channel:
1 is used for the primary language (usually English).
2 is sometimes used for a second language (may vary by region).
3 is sometimes used for a third language (may vary by region).
4 is sometimes used for a fourth language (may vary by region).
Digital Captions
Set captions for digital programs. This function
will help choose and set available language,
font, size and style of digital captions.
1.
2.
Use the CURSOR PAD , , or to highlight
and select desired DIGITAL CAPTIONS feature.
Press EXIT to quit menu or select SET CLOSED
CAPTION to return to the previous menu.
Setup
Set The Closed Captions
Caption Display
:
Off
Analog
Mode
Channel
:
:
Captions
1
Digital
Language
Font
Size
Style
:
1(Unknown)
Default
Standard
Standard
Hitachi
Move
:
:
:
SEL Return
NOTE: 1. Some types of digital closed captions will not work with this TV.
2. Caption Display will not work when viewing a 480p, 720p, or 1080i input via the
COMPONENT: Y-PBPR inputs.
3. Digital Captions Font Style are sometimes different from the Font Style of Analog Captions.
4. Closed Caption and Digital Captions availability and content depends on the broadcaster. Closed
Caption is available when Closed Caption icon is displayed on screen.
65
Setup
Set The Output Terminals
This feature will select the source of the Output
Terminal.
Setup
Set The Menu Options
OR
Set The Power Saving
Set The Inputs
Set The Closed Captions
Video Out :
• Select MONITOR to output the audio and
video signals of the chosen input source
(CABLE, AIR or INPUT 1-5) to a VCR or
other A/V device.
Set The Output Terminals
Set The Quick Start Options
Reset The Software
Move
• Select TV TUNER OUT to output the audio
and video signals of the last watched Antenna
Source (CABLE, AIR).
SEL Select
Setup
Set The Output Terminals
OR
Video Out : Monitor
Aud io Out : Fixed
Audio Out:
• Select AUDIO OUT FIXED to have the Audio
at fixed volume.
IR Out
Move
:
Normal Length
SEL Return
• Select AUDIO OUT VARIABLE to have Audio
volume that can be controlled by the LCD TV
Volume Up/Down.
Video Out
Monitor
Monitor
Audio Out
Fixed
Variable
TV Tuner Out Fixed
Use
To record currently viewed Video and Audio.
When an external device like a monitor
or Hi-Fi audio system is connected to the
audio and video output of the TV. You can
control the volume output by changing the
volume of the TV.
To record currently viewed Video and Audio
from either Cable or Air.
On-Screen Display
IR Out :
• Select IR OUT NORMAL LENGTH to pass remote control signal to IR Out Terminal as is and reach 2m (max)
through provided IR Blaster CABLE.
• Select IR OUT EXTENDED LENGTH to process remote control signal to IR Out Terminal and reach 5m (max)
through provided IR Blaster CABLE.
NOTE : Extended Length funtion is not available for some kinds of external components. For those components
use Normal Length funtion, or point the remote control directly at the external components.
1.
2.
3.
Use CURSOR PAD or or CHANNEL WHEEL to highlight the function to change.
Use the CURSOR PAD or to select the function.
Press EXIT to quit menu or select SET THE OUTPUT TERMINALS to return to previous menu.
NOTE: 1.
2.
When TV TUNER OUT is selected, VARIABLE AUDIO OUT will not be available (grayed out).
When using MONITOR OUT for recording, set the VIDEO OUT to MONITOR.
MONITOR: Available Monitor Out Signals
Input Mode
ANT
(Air or
Cable)
Input 1
Input 2
Input 3
Input4
Input 5
66
S-Video
Digital No Macrovision S-Video YES
Channel Macrovision S-Video
Analog Channel
Video
HDMI_1
S-Video_1
YES
Video_1
HDMI_2
S-Video_2
YES
Video_2
Y-PbPr_3
Video_3
Y-PbPr_4
Video_4
HDMI_5
Y-PbPr_5
Video_5
-
Monitor Out
Video L/R
YES YES
YES YES
YES YES
YES YES
YES YES
YES YES
YES YES
YES YES
YES YES
TV TUNER OUT: Available Monitor Out Signals
Input Mode
HiFi
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
ANT
(Air or
Cable)
Input 1
Input 2
Input 3
Input4
YES
YES
Input 5
Digital No Macrovision S-Video
Channel
Macrovision S-Video
Analog Channel
Video
HDMI_1
S-Video_1
Video_1
HDMI_2
S-Video_2
Video_2
Y-PbPr_3
Video_3
Y-PbPr_4
Video_4
HDMI_5
Y- PbPr_5
Video_5
Y-PbPr
Y-PbPr
Y-PbPr
Monitor Out (TV Tuner Out)
S-Video Video L/R
HiFi
YES
YES YES
YES
ANT ANT ANT ANT
YES
ANT
YES YES
YES
ANT ANT ANT
YES
YES YES
YES
ANT ANT ANT ANT
digital
only
Setup
CableCARD Information
Video
Audio
After the CableCARD has been successfully installed,
you can access CableCARD Information menu in the
SETUP menu of the On-Screen Display.
TV Guide On Screen
Channel Manager
Locks
Timers
Follow the instructions below to access the CableCARD
Information menu.
1. Press the MENU button on the Remote Control to
access the Main Menu screen.
2. Use the CURSOR PAD to highlight SETUP in
the Main Menu and press the SELECT button.
Use the CURSOR PAD to highlight CableCARD
Information and press the SELECT button.
3.
4.
Setup
Power Swivel
Move
Setup
Set The Menu Options
OR
Set The Power Saving
Set The Inputs
To view the CableCARD ID and Host ID, use the
CURSOR PAD to highlight CableCARD Info and
press the SELECT button.
NOTE:
SEL Select
Set The Closed Captions
Set The Output Terminals
CableCARD Information
Set The Quick Start Options
Reset The Software
The Diagnostics Info. window is for
Service use only.
Move
THINGS TO CHECK WHEN USING THE
CableCARD / CableCARD Services
SEL Select
Setup
CableCARD Information
1.
Check that the CableCARD is properly inserted in
the CableCARD slot.
2. Remove the CableCARD by pulling
the CableCARD straight out.
4.
CableCARD Info.
OR
Select the button below to access
CableCARD and Host Diagnostics.
Diagnostics Info.
Move
SEL Return
Visually inspect the CableCARD to ensure all pinholes are in good condition, with none blocked or
damaged.
Make sure the CableCARD is re-inserted in the
correct direction, then slowly push until it is fully
seated in the slot.
5.
When the CableCARD is installed, note all screen
messages that appear (“CableCARD Installed”,
“Acquiring Data”, “CableCARD is not Installed”).
If the “CableCARD Installed” message does not
appear when card is installed, check the TV’s card
slot and CableCARD pins for obstructions or
damage.
6.
If problems still remain, please contact your Cable
Service Provider.
NOTES:
1.
2.
On-Screen Display
3.
Select the button below to acess
CableCARD ID and Host ID.
In order to start cable service
for this device, please contact
your cable provider
CableCARD(tm): 123-456-789-1
Host: 123-456-789-1
Data: 123-456-789-1
Unit Address: 123-456-789-1
Press EXIT to return
When a CableCARD is installed, Auto
Channel scan will not be needed
because the channel list is automatically
loaded to the TV's channel memory.
The TV will take several minutes to
detect and recognize the presence of the
CableCARD. This process must be
completed before any CableCARD
information or Channel listings is
accessed.
67
Setup
Set The Quick Start Options
This feature will select QUICK START UP options. Set
this feature to ON to have the TV tune channels (both
Analog and Digital) quickly when first turning the TV on.
Set this feature to OFF to save electricity. Selecting ON
for the QUICK START UP feature will activate the TV
tuners circuits when the TV is in “standby mode” which
is commonly referred to as “off”. This will allow you to
quickly tune to channels when first turning the TV on.
Digital signals often change and this feature will
monitor any changes and prepare the television to
quickly present a picture. A small amount of electricity
is used to continually monitor signals when this feature
is selected.
Setup
Set The Menu Options
OR
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
Set The Quick Start Options
Reset The Software
Move
SEL Select
Setup
Set The Quick Start Options
OR
Select ON to have the TV tune
channels quickly at 1st turn on.
Select OFF to save electricity
Off
On
SEL Select
Move
On-Screen Display
NOTE:
When setting the Quick Start option to ON
the option of Reset TV Settings will not
operate.
Reset The Software
Setup
Set The Menu Options
This feature shows software information and easy
upgrade procedure. This function allows the TV
software to be upgraded by using a flash card (MMC
CARD). If a future software upgrade is required for your
TV, HITACHI will notify and provide you with a flash
card. In order to receive written notification and the
flash card, please complete and return the warranty
card.
OR
Set The Power Saving
Set The Inputs
Set The Closed Captions
Set The Output Terminals
Set The Quick Start Options
Reset The Software
Move
SEL Select
Setup
1.
Insert MMC CARD
Reset The Software
OR
2.
Press the CURSOR PAD or to highlight
UPGRADE NOW.
3.
Press the SELECT button to select and start
upgrading.
4.
Unplug the AC power cord when the UPGRADE is
complete.
NOTE: Any power interruption during the upgrade
process will cancel the upgrade. When this
happens, repeat the upgrade procedure.
68
MMC Software Upgrade:
Main Vxxxx.xxxx
Upgrade Now
Please Insert MMC card
before upgrading.
Reset TV Settings
(Select "Yes" to return all settings to the factory
default after main power OFF/ON.)
No
Yes
Move
SEL Return
Setup
Reset TV Settings
This function allows you to Reset all TV Settings to the
original factory settings on all modes during the next
main power on/off.
Setup
Reset The Software
MMC Software Upgrade:
Main Vxxxx.xxxx
Upgrade Now
1.
Use CURSOR PAD , to highlight functions.
Please Insert MMC card
before upgrading.
2.
Press the SELECT button or CURSOR PAD to
select Reset The Software.
Use the CURSOR PAD to access the Reset TV Settings
option.
Select the "YES" option to Reset ALL the TV Settings during the
next main power on/off.
Reset TV Settings :
Select "Yes" to return all settings to the factory
to the factory default after main power OFF/ON.
No
Yes
3.
4.
Move
SEL Return
NOTE: If YES is selected, ALL TV MENU SETTINGS will be reset to the original factory settings on all
modes during the next power on/off.
Power Swivel
This feature controls the motorized stand. It allows
the customer to turn the display left or right using
the remote control. This feature is only available
when the Table Top Stand is connected.
Video
Audio
TV Guide On Screen
Channel Manager
Locks
Timers
1.
Press the CURSOR PAD to rotate the TV to
the right.
3.
Press the CURSOR PAD to rotate the TV to
the left.
4.
Release the CURSOR PAD to stop rotation.
Power Swivel
Move
SEL Select
On-Screen Display
2.
Setup
Use the CURSOR PAD or to unlock or lock
the Power Swivel.
Exit the OSD menu system before controlling the
motorized stand.
or
Power Swivel
Select
Locked
SEL
Return
NOTE: 1. The Power Swivel has a maximum turning radius of 30° (left and right).
2. Do not place any objects in the path of the monitor when using the power swivel feature.
3. Before using the power swivel, please make sure that the path of the monitor is clear of any
fingers, hands or any other body parts to avoid causing injury.
4. When the Picture-In-Picture (PIP) or Freeze mode is ON, the Power Swivel is disabled.
69
Equipment Care and Troubleshooting
DO
DO NOT
Dust the screen and cabinet with a soft cloth.
Do not clean your screen with strong cleaners, polishes
or a chemically treated cloth.
Clean the screen with a soft cloth moistened in warm
water and dry with a soft cloth. A mild soap may be
used if the screen is extremely dirty.
Do not place rubber or vinyl products or cellophane
tape on your LCD Television.
Place your LCD Television away from extreme heat,
humidity, and extremely dusty places.
Avoid repeatedly touching the screen.
Do not subject the remote control to shocks such as
dropping it on the floor, etc. This may cause damage to
the precision parts.
Remove the plug from the wall outlet if your LCD
Television will not be used for a long period of time, for
instance, when you go on vacation.
Avoid placing the remote control in a high humidity
place or getting it wet. Do not leave it on or near a
heater. Excessive heat or moisture may cause the unit
to fail.
When the batteries run down, remote control operation
will become erratic or become unresponsive. Replace
the old batteries with two new “AA” size batteries. Do
not use an old battery with a new battery.
Exposing the screen to direct sunlight for a long period
of time or heat may cause damage to the LCD
screen.
TROUBLESHOOTING
Your HITACHI LCD Television incorporates advanced power surge protection technology designed to protect
against component or circuit damage due to external or internal voltage power surges.
70
V)
ire
d-i
nw
쏹 쏹 쏹
쏹
Picture blurred 쏹
쏹
쏹 쏹 쏹
쏹
Lines or streaks in picture
쏹
쏹 쏹 쏹
쏹
Poor reception on some channels
쏹
쏹 쏹 쏹
쏹
Picture rolls vertically
쏹
tro
fer
tne
ss
on
nte
r
st c
rig
h
tra
st B
on
loc
al i
con
tro
olo
l
rc
on
tro
st T
l
int
con
Ad
tro
jus
l
tV
o lu
me
con
tro
l
쏹
jus
tC
Picture OK, sound poor 쏹
Ad
ju
쏹
Ad
쏹
jus
tC
쏹 쏹
Ad
쏹
Ad
ju
Sound OK, picture poor 쏹
l
en
ce
lea
a
ken
nn
nte
Ch
eck
ou
tsid
ea
for
eck
eck
쏹
Ch
쏹 쏹 쏹 쏹 쏹
No Picture, no sound 쏹
for
le)
ck
of T
ub
ba
tro
s(
tion
ctio
n
ne
con
na
na
ten
nn
ha
rc
ten
an
eck
an
N"
''O
el (
sta
ed
the
no
Try
a
bro
ect
in
is c
orr
ed
gg
ss
wit
ch
tion
plu
cor
d is
er
Vi
Ch
This protective technology
should provide for years of
lasting entertainment from
your HITACHI LCD
Television.
Ch
3.
SYMPTOMS
sur
eT
2.
Press the POWER
SWITCH (ON/OFF
SWITCH) once.
If there is still no power,
wait 30 seconds and
press the POWER
SWITCH again.
If there is still no power,
unplug the power cord
from the wall. Wait 30
seconds and plug the
power cord back in.
Press the POWER
SWITCH again.
Be
1.
CH
TR ECK
Y T TH
HE ES
SE E IT
Be
AD EM
sur
JU
ee
S
xte
ST AN
Be
rna
ME D
sur
l co
NT
ep
nn
S
ec
ow
Useful Information
IF YOUR TELEVISION SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS
PROCEDURE:
쏹 쏹
쏹
쏹
No color 쏹
쏹
쏹 쏹 쏹
쏹
Poor color 쏹
쏹
쏹 쏹 쏹
쏹
쏹
Reception Problems
IGNITION NOISE:
Black spots or horizontal streaks may appear, picture may flutter or drift.
Usually caused by interference from automobile ignition systems, neon lamps,
electrical drills, and other electrical appliances.
GHOSTS:
Ghosts are caused by the television signal following two paths. One is the
direct path and the other is reflected from tall buildings, hills or some other
objects. Changing the direction or position of the antenna may improve
reception. Ghosting may also be caused by defects in the antenna system such
as unshielded leads or connecting several sets to the same antenna without
using multiple antenna couplers.
SNOW:
If your receiver is located in the fringe area of a television station where the
signal is weak, your picture may be marred by the appearance of small dots.
When the signal is extremely weak, it may be necessary to install a special
antenna to improve the picture.
Useful Information
RADIO FREQUENCY INTERFERENCE:
• RADIO FREQUENCY INTERFERENCE:
The interference produces moving ripples or diagonal streaks, and in some
cases, causes loss of contrast in the picture.
• PREVENTION OF AN OBSTACLE TO RADIO RECEIVERS
This television has been designed pursuant to the FCC class B Rules. This is to prevent a problem to Radio
receivers. If this television causes a problem to Radio receivers, then take the following steps:
- Keep the television away from Radio.
- Adjust Radio antennas in order for the television not to receive interference.
- The antenna cable of Radio should be kept away from the television.
- Use a coaxial cable for antenna.
You can check if this television influences Radio receivers by turning off all other equipment other than the television.
If you find a problem receiving Radio when using the television, check the instructions mentioned above.
BLOCK NOISE (DIGITAL INPUT):
Fuzzy blocks may appear in some area or the whole area of the screen. This is
usually caused by interference from automobile ignition systems, neon lamps,
electrical drills, ghosting of the image and weak signals.
BLACK SCREEN:
When using an antenna, weak signals will display a black screen. It may be
necessary to upgrade your antenna.
NOTE: The TV set can generate sound distortion in external devices such as a radio. Please separate radio
equipment from the TV set to a considerable distance.
71
Troubleshooting
1. LCD Television Troubleshooting
IMPORTANT NOTES
No.
Items
Notes
1
Arching sound from LCD
display monitor’s panel.
A buzzing sound might be heard when the LCD display monitor is turned on in a very quiet room. This is due to the LCD panel
drive circuit when it is functioning. This arching sound is normal and it is not a malfunction.
2
Interference for infrared
equipment.
Some infrared rays are emitted from the LCD display monitor’s panel that might affect other infrared controlling equipment.
3
Picture Image (Spectrum)
When receving still picture signals, (e.g. channel number indication or clock indication) for a while, you can see image-like
when the picture varied. This is not a defect.
4
LCD Surface
The LCD panel is made from glass. Heavy shock on the front panel might damage it.
5
Transportation
When the LCD monitor is transported horizontally, the glass panel has the possibility of being broken or increasing the picture
defects. At the time of transportation, horizontal style is prohibited. More-over, please treat the LCD panel with great care
because of a precision apparatus. Please instruct transporters so that it should be put into the packing box at the time
of shipment.(There is a possibility that breakage of the panel or defects will increase.) Rough transportation might cause
damage to the panel and pixel failure.
6
Granular spots
When a screen is seen at point-blank range, a random fine grain may be visible to a dark part.
7
8
Black dots and
Bright Points
Disturbance to video
apparatus
Black dots and Bright points may appear on the LCD screen. This is a structural property of the LCD panel and is not
a defect.
If an apparatus (VCR, etc.) antenna line is arranged near the monitor, the image may shake, or disturbance may be
received.
9
Lip Sync
There is some time lag betweeen the picture and the sound. You can see lip motion that is delayed compared to the sound.
10
Caution on prolonged
storage
Storing the LCD television for a period of more than 2 to 3 months without use might cause an unstable picture when
the set is turned on.
11
Operating
Operating altitude: 800 to 1,114hPa (6,194ft to -2,484ft). Operating temperature: 41 F to 95 F.
Avoid operating the LCD TV below 41 F LCD response speed may slow down when operating at these temperatures.
This is a normal operating characteristic of the LCD monitor.
12
Storage
Storage Altitude: 300 to 1,114hPa (31,912ft to -2,484ft). Storage temperature: 5 F to 140 F.
13
Power ON or OFF
Frequent use of the Power ON or OFF might trigger the power protection circuit. If the TV does not turn ON, please wait
a little before turning ON again.
2. TV Guide On-ScreenTM System Frequently Asked Questions
My Guide listings disappeared after a power failure.
You should begin to receive listings again within 24 hours.
Some channel numbers in the Guide are incorrect.
You can correct them using Change Channel Display under Setup.
I have not received any Guide show listings.
Listings usually begin to appear within 24 hours after a successful Setup. It may take up to 5 days to receive a full
8 days of program listings.
• Check the connections between the TV, cable, antenna, and the IR cable if using a cable box.
• Verify Setup information under Change System Settings.
• Make sure the cable box is On, if applicable.
• Review Screen 4 and Screen 5 in the Initial Guide Setup section.
Useful Information
A show I set to Record did not occur.
• Make sure your recorder is turned Off before the recording begins.
• Make sure there is a tape or DVD in the VCR or DVD Recorder.
• Check the Schedule menu and verify that the show is listed before recording begins.
• Check the placement of the IR cable in front of your recorder.
The TV did not tune to a show I scheduled with the Reminder feature.
• Check the Schedule menu and verify that the show is listed.
• If you have a cable box, check the IR cable.
I set a show to Auto-Tune and it did not.
• Check the Schedule menu and verify that the show is listed as a Reminder.
• Highlight the show under Listings and do the following:
• Press the Menu button on the remote.
• Use the down arrow to highlight Edit Reminder, and press SELECT.
• Verify the Auto-Tune option reads Yes.
• The TV must be On at the scheduled time for Auto-Tune.
I set a show with the Power On TV option and it did not.
• Check the Schedule menu and verify that the show is listed as a Reminder.
• Highlight the show under Listings and do the following:
• Press the Menu button on the remote.
• Use the down arrow to highlight Edit Reminder, and press SELECT.
• Verify the Power On TV option reads Yes.
• The TV must be Off at the scheduled time for Power On TV.
72
Troubleshooting
TV Guide On-ScreenTM Frequently asked
quiestions continued
If I add a recorder or change my cable service, how
do I change my Setup information?
1)
Highlight the Setup Service in the Guide.
2)
Use the down arrow to select Change
System Settings.
3)
Follow the on-screen instructions.
A show entry in the Guide reads “No Listing.” What
does that mean?
Show information for that entry was not available
during the last Guide information update (download).
Show information is updated on a daily basis.
When I entered the Guide, I was asked to choose
from more than one channel lineup. What should I
do?
Select the lineup that most closely matches the one for
your area. If after you choose the lineup, you want to
make changes to:
1)
Highlight the Setup Service in the Guide.
2)
Use the down arrow to select Change
Channel Display.
3)
Follow the on-screen instructions.
What do the color for shows in the Listings and
Search screens indicate?
Green=Sports; Dark Blue=Children’s; Purple=Movies;
Teal=Other Show
If I have a power outage, do I need to complete
Setup again?
No; Setup information is stored in TV Guide On Screen.
Help is also available in a Panel Menu. Press the Info
Button to display an Expanded Info Box; press Info
again to close the box.
After some show titles, I have noticed from 1 to 4
stars (****). What does that mean?
These stars are a broadcast-industry rating system
used to inform you of a show’s quality. The more
stars, the better the rating.
I have seen the word “download” in reference to the
Guide. What does that mean?
A download sends channel and show information to a
TV Guide On Screen device. A download happens at
least once a day.
How can I look for a specific show in the Guide?
Search lets you find shows by Category (HDTV, Movies,
Sports, Children, Educational, News, Variety, Series),
Keyword, or Alphabetical.
In the United States, TV GUIDE and other related marks
are registered marks of Gemstar-TV Guide International,
Inc. and/or one of its affiliates. In Canada, TV GUIDE is
a registered mark of Transcontinental Inc., and is used
under license by Gemstar-TV Guide International, Inc.
The TV Guide On Screen system is manufactured under
license from Gemstar-TV Guide International, Inc.
and/or one of its affiliates.
The TV Guide On Screen system is protected by one or
more of the following issued United States patents
6,498,895; 6,418,556; 6,331,877; 6,239,794; 6,154,203;
5,940,073; 4,908,713; 4,751,578; 4,706,121.
Useful Information
Is Help available in the Guide? If so, how do I find
it?
Yes. Highlight any of the 5 main Services (i.e., Listings,
Schedule, Recordings, Setup, Search) and press the
Info Button. An Expanded Info Box displays additional
help information; press Info again to close the box.
Remind feature. Highlight Schedule and press menu.
Choose the event type, press SELECT and then enter
date, start and stop time, channel number, etc.
What do the frequencies for Record and Remind
mean?
•
Once—records/reminds the show one time
•
Daily (manual only)—records/reminds the
time, channel, and input combination Monday
through Friday
•
Regularly— records/reminds for the
channel/time combination on any day of the
week, on the same channel
•
Weekly— records/reminds for the channel/
time combination on a specific day of the
week
•
Off (not cancel)—keeps the show in the list
but will not record/remind the show until the
frequency is changed
Gemstar-TV Guide International Inc. and/or its related
affiliates are not in any way liable for the accuracy or
availability of the program schedule information or other
data in the TV Guide On Screen system and cannot
guarantee service availability in your area. In no event
shall Gemstar-TV Guide International, Inc. and/or its
related affiliates be liable for any damages in connection
with the accuracy or availability of the program
schedule information or other data in the TV Guide On
Screen system.
Can I set a Record or Remind event without
highlighting a show title in the Guide?
Yes. TV Guide On Screen has a Manual Record and
73
Useful Info
AGENCY REGULATORY INFORMATION
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
FCC Information
This device complies with part15 of the FCC Rules.Operation is subject to the following two conditions :
(1) This device may not cause harmful interference and (2) This device must accept any interference
received, including interference that may cause undesired operation.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not
expressly approved by Hitachi America ,Ltd. Home Electronics Division may void the user’s authority to
operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to
maintain compliance with FCC Rules and Regulations.
Any cables that are supplied with the system must be replaced with identical cables in order to assure
compliance with FCC rules. Order Hitachi spares as replacement cables.
Note
This LCD Television receiver will display television closed captioning, (
paragraph 15.119 of the FCC rules.
or
Useful Information
INDUSTRY CANADA AGENCY REGULATORY INFORMATION
Cable Compatible Television Apparatus- Tèlèvision câblocompatible, Canada.
74
), in accordance with
Features and Specifications
Features:
•
•
•
•
•
•
•
•
•
•
•
•
•
New Easy-to-Use On-Screen Menu Control (3
Language)
Downloadable V-Chip
IR OUT/G-LINK System Control
- Control your components with one remote
control.
- 2 IR Blaster cables included
Illuminated and Preprogrammed Remote Contr ol
Power Management: ON/OFF via signal detection
Picture Enhancement
Input Signal Identification
CableCARD compatible - Contact your local cable
operator for mor e information
HDMI (High Definition Multimedia Interface)(High
Bandwidth Digital Content Protection V1.1
Compatible)
Photo Input (for your digital camera, USB drive or
memory card USB drive)
Technology
TV Guide On ScreenTM
Outputs:
•
•
•
Audio:
•
•
•
•
•
•
•
•
•
•
•
•
1366 x 768 Display Resolution
IPS (In-Plane Switching Technology)
Wide Viewing Angle: More than 160°
Color Temperature Presets: High, Standard,
Medium and B/W .
Multiple Screen Fill Modes
(4:3 Standard/4:3 Expanded/4:3 Zoom 1/
4:3 Zoom 2/16:9 Standard1/Standard2/16:9 Zoom)1
4MB 10-bit 3D Y/C Comb Filter
Picture Modes :Day(Normal), Day(Dynamic) and Night
Inputs:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
S-Video
Luminance (Y) . . . . . . . . . . . . . . . . . 1.0Vp-p, 75 Ohm
Chrominance (C) . . . . . . . . . . . . . 0.286Vp-p, 75 Ohm
Component Video
Luminance (Y) . . . . . . . . . . . . . . . . . 1.0Vp-p, 75 Ohm
Chrominance (PB/P R) . . . . . . . . . . . 0.7Vp-p, 75 Ohm
Audio input Impedance . . . . . . . . . . . . . . . . 270k Ohm
Average input level . . . . . . . . . . . . . . . . . . . 470mVrms
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (19 PIN)
Remote Control
Batteries (AA)
6' AC Power cord cable
Table Top Stand
IR Blaster Cables
Power Swivel Cable
Ferrite Core
Optional Accessories:
For U.S. Models: Please access our website:
www.hitachi.us/tv
INPUTS/OUTPUTS
•
•
•
•
•
•
•
•
•
•
•
•
Wideband Component Y, Pb,Pr . . . . . . . . . . . . . . . . 3
Composite Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
S-Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Antenna (RF)Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Audio Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Monitor Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Optical Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
IR Blaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
G-LINK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CableCARD Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Upgrade Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Swivel Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
•
•
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Photo Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Useful Information
•
•
Power Input . . . . . . . . . . . . . . . . . . . . .AC 120V, 60Hz
Power Consumption
- Refer to rear panel at the back of the LCD Television
Receiver
Antenna input impedance . . . . . . . . . . . . . . . .75 Ohm
Channel coverage . . . . . . . . . . . . . . . . . . . . . . . 191ch.
VHF-Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ~ 13
UHF-Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ~ 69
CATV Mid Band . . . . . . . . . . . . . . . . . . . . . . A-5 ~ A-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-I
Super Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J-W
Hyper Band . . . . . . . . . . . . . . . . . . . . . . . W+1 - W+28
Ultra Band . . . . . . . . . . . . . . . . . . . . . . . W+29 - W+94
Television System . . . . . . . . . . . . . . . NTSC Standard
ATSC Standard (8 VSB, 64-QAM, 256-QAM)
Video . . . . . . . . . . . . . . . . . . . . . . . . 1.0Vp-p, 75 Ohm
MTS Stereo/SAP
Bass Boost
Surround Sound
20W
Soft Mute (50%)
Supplied Accessories:
•
Video:
Video 1.0Vp-p. 75 Ohm
Audio . . . . . . . . . . . . . . . . . . . . . . .470mVrms, 1k Ohm
Optical Out (Digital Audio) . . . . . .1 Optical Connector
SPECIFICATIONS
•
Pixel Pitch . . . . 0.60(horiz.) x 0.60(vert.) mm.
• FCC class: . . . . . . . . . . . . B for Consumer Use
• Power Requirements:. . . . . . . . 108-132VAC, 60Hz
1
Screen mode availability varies by input format
HDTV Televisions display HDTV only when an HDTV source is available.
All specifications, weights, and dimensions are subject to change without
prior notice. Please access www.hitachi.com/tv for detailed specifications
and dimensions for custom installations.
UltraVision Digital is a registered trademark of Hitachi Home Electronics
(America), Inc.
㪚㪦㪧㪰㪩㪠㪞㪟㪫㩷㪺㩷㪈㪐㪐㪐㪄㪉㪇㪇㪍㩷㪤㪦㪥㪫㪘㪭㪠㪪㪫㪘㩷㪪㪦㪝㪫㪮㪘㪩㪜㪃㩷㪠㪥㪚㪅㩷㪘㪣㪣㩷㪩㪠㪞㪟㪫㪪㩷㪩㪜㪪㪜㪩㪭㪜㪛㪅
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI Licensing
LLC.
*Manufactured under license from Dolby Laboratories. “Dolby” and the
double-D symbol are trademarks of Dolby Laboratories.
75
Set Dimensions
37 Inch Models (Includes Table Top Stand) Weight (lbs./kg): 63.9/29
A
B
C
L
K
M
G
H
E
D
J
I
N
F
Units
A
Inches 37-3/8
Useful Information
MM
76
949.4
B
C
D
2-1/2
2-1/2
28-9/16
62.9
62.9
725.7
E
F
26-3/16 19-1/8
664.3
485.3
G
H
K
L
16-11/16
14-1/4
32-7/16
18-5/16
4-3/4
3/4
424.1.
362.7
823.6
464.8
120.9
20.2
I
J
M
N
3-15/16 14-3/8
100.7
365
Hitachi
Service Hotline
To locate an authorized HITACHI
service facility in the continental
U.S.A. and Canada,
DIAL TOLL FREE
7 days a week, 24 hours a day
1-800-HITACHI
(1-800-448-2244)
HITACHI AMERICA, LTD.
HOME ELECTRONICS DIVISION
HITACHI CANADA, LTD.
DIGITAL MEDIA DIVISION
HITACHI has made every effort to assure you hours of
trouble free operation from your unit. However, should
you require service, a network of HITACHI Authorized
Service Facilities has been established in all 50 states
and Puerto Rico. Each facility will provide you with
convenient and expedient assistance. Our service
hotline operator will direct you to the HITACHI
Authorized Service Facility nearest you. Just present
proof of purchase and/or delivery receipts to the
Hitachi Authorized Service Facility, and service will be
rendered in accordance with the terms of the limited
warranty as stated on your warranty card or operating
guide.
Should you have any questions regarding warranty,
service, operation, or technical assistance, please
contact:
Should you have any questions regarding warranty,
service, operation, or technical assistance, please
contact:
Pour de plus amples renseignements sur le service
durant la période couverte par la garantie, sur le
fonctionnement ou pour de l’assistance technique
communiquez avec:
Monday – Friday (EST).........................9:00am – 7:00pm
Saturday (EST) .....................................9:00am – 5:00pm
Look for your French Manual on the outside of the
box. If the manual is missing, call 1-800-HITACHI
(1-800-448-2244) for a copy.
Useful Information
Hitachi America, LTD.
Home Electronics Division
900 Hitachi Way
Chula Vista, CA 91914-3556
In Canada: 1-800-HITACHI (1-800-448-2244)
Au Canada: 1-800-HITACHI (1-800-448-2244)
Lundi - Vendredi L’EST ........................9:00am – 7:00pm
Samedi L’EST.......................................9:00am – 5:00pm
La version français de votre manual se trouve a
l’exterieur de la boîte. Si le manuel est manquant,
coposez le 1-800-HITACHI (1-800-448-2244) pour
obenir votre copie.
HITACHI CANADA, LTD.
1-2495 Meadowpine Blvd.
Mississauga, Ontario L5N 6C3
77
Service Information
When you call HITACHI SERVICE HOTLINE they will require some information related
to the TV MODEL NAME and SERIAL # in order to give you the proper support. This
information is located on the back of the TV and also on the RIGHT SIDE of your TV
set. Please follow the next steps to find this information and then provide to SERVICE.
쐃 Look on the right side of the TV.
쐇 Locate the LABEL where it shows the information
related to MODEL NAME and SERIAL #.
쐋 HITACHI Service Department will require this
information in order to give you the proper
support regarding your questions.
쐃
Useful Information
쐇
78
End User License Agreement for HITACHI DTV Software
END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE
IMPORTANT – READ CAREFULLY: This End User License Agreement for
HITACHI DTV Software (this “Agreement”) is a legal agreement between
you (“you” or “your”), in your capacity as the owner of a HITACHI brand
digital television (the “DTV”), and HITACHI America, Ltd., Ubiquitous
Platform System Division ("HITACHI"). By using the DTV or the digital
television software installed on the DTV (the "DTV Software") or any
Upgrade (as defined below, and together with the DTV Software, the
“Software”), you agree to be bound by the terms and conditions of this
Agreement. IF YOU DO NOT AGREE TO BE BOUND BY THIS LICENSE
AGREEMENT, DO NOT USE THE DTV OR THE DTV SOFTWARE.
1.
2.
3.
VIOLATIONS; INDEMNITY. You understand and agree that your
use of the Software in any manner except as permitted under this
Agreement could constitute a serious crime and could subject you
to damages and an award to HITACHI of attorneys’ fees in
connection with your violation of this Agreement. You further
understand that you may be held legally responsible for any
copyright infringement or other violation of intellectual property
rights caused or facilitated by your failure to abide by the terms of
this Agreement. You agree to defend, indemnify and hold HITACHI
and its parent and affiliate companies harmless from and against
any and all liability resulting from any breach by you of this
Agreement.
INTELLECTUAL PROPERTY. The Software is protected by federal
copyright laws, international copyright treaties and other intellectual
property laws and treaties. The Software is licensed, not sold, to
you. All right, title and interest in and to the Software and any
intellectual property associated therewith, including any
accompanying printed materials, shall belong to HITACHI and its
licensors and suppliers. Except as expressly provided herein,
neither HITACHI nor any of its licensors or suppliers grants to you
under this Agreement any express or implied right in or to any
patents, copyrights, trademarks, trade secrets or other intellectual
property. All right, title and interest in and to the intellectual
property rights associated with any content that is accessible
through use of the Software shall belong to the applicable content
owners and may be protected by copyright or other intellectual
property laws and treaties. This Agreement grants you no rights to
use such content. Any rights of HITACHI not expressly granted to
you hereunder are reserved expressly by Hitachi.
SOFTWARE UPGRADES. In the future, HITACHI may release or
make available one or more upgrades to the DTV Software
(each, an “Upgrade”). You understand and agree that if you decide
to install or use any Upgrade, your installation and use of such
Upgrade and/or any other software or intellectual property
HITACHI may provide in connection therewith shall be governed by
the terms and conditions of this Agreement, except to the extent
that HITACHI provides different or supplementary license terms or
conditions that accompany such Upgrade or other software or
intellectual property. In the event HITACHI provides you with a
“flash card” or other media to effect or facilitate an Upgrade, you
understand and acknowledge that your failure to return such flash
card or other media to HITACHI as HITACHI may require could
result in HITACHI placing your name and your DTV’s serial number
on a “No Further Upgrades” list, which will prohibit you from
receiving any subsequent Upgrades HITACHI may later release or
make available. IF YOU DO NOT AGREE WITH ALL THE TERMS
AND CONDITIONS OF THIS AGREEMENT OR ALL THE TERMS
AND CONDITIONS OF ANY DIFFERENT OR SUPPLEMENTARY
LICENSE THAT MAY ACCOMPANY SUCH UPGRADE, (A) DO NOT
USE ANY HITACHI-PROVIDED FLASH CARD OR OTHER MEDIA,
(B) DO NOT
INSTALL ANY HITACHI-PROVIDED
UPGRADE SOFTWARE ON YOUR DTV, AND (C) PROMPTLY
RETURN SUCH FLASH CARD OR OTHER MEDIA TO HITACHI.
EXPORT RESTRICTIONS. HITACHI is licensing the Software for
use within North America only. You agree that you will not export or
re-export the Software. You specifically agree not to export or reexport the Software: (i) to any country to which the U.S. has
embargoed or restricted the export of goods or services, which
currently include, but are not necessarily limited to Cuba, Iran,
Libya, North Korea, Sudan and Syria, or to any national of any such
country, wherever located, who intends to transmit or transport the
Software back to such country; (ii) to any person or entity who you
know or have reason to know will utilize the Software in the design,
development, or production of nuclear, chemical, or biological
weapons; or (iii) to any person or entity who has been prohibited
from participating in U.S. export transactions by any federal agency
of the U.S. government. You warrant and represent that neither the
U.S. Bureau of Industry and Security nor any other U.S federal
Agency has suspended, revoked, or denied your export privileges.
6.
NO WARRANTIES. The software is provided to you in "as is”
condition and HITACHI makes no warranties of any kind
whatsoever regarding the software and, to the maximum extent
permitted by law, hereby expressly disclaims all warranties of any
kind whatsoever, express or implied, with respect to the software.
All implied warranties, including without limitation, the implied
warranties of non-infringement, merchantability and fitness for a
particular purpose are hereby expressly disclaimed by hitachi to
the maximum extent permitted by law.
7.
LIMITATION OF LIABILITY. To the maximum extent permitted by
applicable law, HITACHI, its licensors, suppliers, parent
companies, affiliates, subsidiaries, employees and agents shall not
under any circumstances be liable to you or any third parties for
any damages of any nature arising in any way from this agreement,
your use of the software or otherwise, whether indirect, special,
incidental, consequential or otherwise, including, without limitation,
any claims for lost profits, lost good will, lost data, business
interruption, procurement of substitute goods or services, or
expenditures made or committed for in reliance on the continuation
of this agreement, even if advised in advance of the possibility of
such damages.
8.
NO FAILURE OF ESSENTIAL PURPOSE. You agree that neither
HITACHI' S breach of this agreement nor its failure to repair a
defect, error or bug in the software shall constitute a failure of the
essential purpose of this agreement.
9.
CRYPTOGRAPHIC SOFTWARE. The software contains software
developed by the OpenSSL Project, including cryptographic software
written by eric young (the "cryptographic software"). The
cryptographic software is provided by the OpenSSL Project in "as is''
condition and any express or implied warranties, including but not
limited to, the implied warranties of merchantability and fitness for
a particular purpose are hereby expressly disclaimed to the
maximum extent permitted by law. In no event shall the OpenSSL
Project, its contributors, HITACHI or any of its parent or affiliate
companies be liable for any direct, indirect, incidental, special,
exemplary, or consequential damages (including, but not limited to,
procurement of substitute goods or services; loss of use, data, or
profits; or business interruption) however caused and on any theory
of liability, whether in contract, strict liability, or tort (including
negligence or otherwise) arising in any way out of the use of the
software or the cryptographic software, even if advised in advance
of the possibility of such damages.
10.
TERMINATION. HITACHI may terminate this Agreement
immediately at any time by providing notice to you.
11.
GOVERNING LAW; SEVERABILITY. This Agreement will be
governed by the laws of the State of New York, and you consent to
the exclusive jurisdiction and venue in the federal courts sitting in
the Southern District of New York, unless no federal subject matter
jurisdiction exists, in which case you consent to the exclusive
jurisdiction and venue in the Borough of Manhattan, New York,
USA.
License Agreements
4.
LICENSE GRANT. HITACHI grants to you, for the life of the DTV, a
non-exclusive, non-transferable, revocable license to install and
use one copy of the Software on the DTV, subject to the following
limitations and restrictions:
a.
You may not share, duplicate, republish or redistribute the
Software;
b.
You may not resell, rent, lease, sublicense, gift, loan, assign or
otherwise transfer the Software or any of your rights under
this Agreement;
c.
You may not modify, adapt, translate, reverse engineer,
decompile, disassemble or make derivative works from the
Software or use the Software in combination with any nonHitachi software; and
d.
You may not use the Software for any commercial purpose.
5.
79
End User License Agreements for Operating System Software
SOFTWARE LICENSE INFORMATION
Your HITACHI brand digital television (the “DTV”) uses certain open source operating system
software (the “OS Software”) distributed pursuant to GNU GENERAL PUBLIC LICENSE Version
2 and GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, each as defined and published
by the Free Software Foundation, Inc.
The OS Software modules incorporated into the DTV are listed in the table below opposite the
applicable GNU software license. Copies of such GNU software licenses are provided in the
pages that follow.
Software Module
Applicable GNU Software License
Linux Kernal
busybox
dhcpdcd
ifupdow
net-tool
iptables
libstdc++5
GNU GENERAL PUBLIC LICENSE
Version 2
glibc
libposixtime
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1
For purposes of incorporating the OS Software into the DTV, Hitachi made certain modifications
to the source code of the OS Software (collectively, the “Source Code Modifications”) in 2006.
The Source Code Modifications also are distributed pursuant to the applicable GNU software
licenses identified above.
THE OS SOFTWARE AND THE SOURCE CODE MODIFICATIONS ARE PROVIDED “AS IS”
AND THE LICENSEE DISCLAIMS ANY AND ALL WARRANTIES OF ANY KIND, INCLUDING
THE IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. See the GNU General Public License for additional terms and conditions.
License Agreements
If you would like to learn more about the Free Software Foundation or the GNU software project,
please visit http://www.fsf.org. If you would like to request a copy of the Source Code
Modifications from HITACHI, please send an email to the following address:
[email protected]
80
End User License Agreement for Operating System Software
GNU GENERAL PUBLIC LICENSE Version 2, June 1991
Copyright © 1989, 1991 Free Software Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
(YHU\RQHLVSHUPLWWHGWRFRS\DQGGLVWULEXWHYHUEDWLPFRSLHVRIWKLVOLFHQVHGRFXPHQWEXWFKDQJLQJLWLVQRWDOORZHG
Preamble
The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General
Public License is intended to guarantee your freedom to share
and change free software--to make sure the software is free for all
its users. This General Public License applies to most of the Free
Software Foundation's software and to any other program whose
authors commit to using it. (Some other Free Software Foundation
software is covered by the GNU Library General Public License
instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not
price. Our General Public Licenses are designed to make sure
that you have the freedom to distribute copies of free software (and
charge for this service if you wish), that you receive source code
or can get it if you want it, that you can change the software or use
pieces of it in new free programs; and that you know you can do
these things.
To protect your rights, we need to make restrictions that forbid
anyone to deny you these rights or to ask you to surrender the
rights. These restrictions translate to certain responsibilities for
you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether
gratis or for a fee, you must give the recipients all the rights that
you have. You must make sure that they, too, receive or can get
the source code. And you must show them these terms so they
know their rights.
We protect your rights with two steps: (1) copyright the software,
and (2) offer you this license which gives you legal permission to
copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to make
certain that everyone understands that there is no warranty for this
free software. If the software is modified by someone else and
passed on, we want its recipients to know that what they have is
not the original, so that any problems introduced by others will not
UHÀHFWRQWKHRULJLQDODXWKRUV
UHSXWDWLRQV
The precise terms and conditions for copying, distribution and
PRGL¿FDWLRQIROORw.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which
contains a notice placed by the copyright holder saying it may
be distributed under the terms of this General Public License.
The "Program", below, refers to any such program or work,
and a "work based on the Program" means either the Program
or any derivative work under copyright law: that is to say, a
work containing the Program or a portion of it, either verbatim
or with modifications and/or translated into another language.
1. You may copy and distribute verbatim copies of the Program's
source code as you receive it, in any medium, provided that
you conspicuously and appropriately publish on each copy an
appropriate copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this License and to the absence
of any warranty; and give any other recipients of the Program a
copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy,
and you may at your option offer warranty protection in exchange
for a fee.
2. You may modify your copy or copies of the Program or any
portion of it, thus forming a work based on the Program, and
copy and distribute such modifications or work under the terms
of Section 1 above, provided that you also meet all of these
conditions:
a) You must cause the modified files to carry prominent
notices stating that you changed the ¿OHV and the date of
any change.
b) You must cause any work that you distribute or publish, that
in whole or in part contains or is derived from the Program
or any part thereof, to be licensed as a whole at no charge
to all third parties under the terms of this License.
c) If the modified program normally reads commands
interactively when run, you must cause it, when started
running for such interactive use in the most ordinary way, to
print or display an announcement including an appropriate
copyright notice and a notice that there is no warranty (or
else, saying that you provide a warranty) and that users may
redistribute the program under these conditions, and telling
the user how to view a copy of this License. ([FHSWLRQ if
the Program itself is interactive but does not normally print
such an announcement, your work based on the Program is
not required to print an announcement.)
License Agreements
Finally, any free program is threatened constantly by software
patents. We wish to avoid the danger that redistributors of a free
program will individually obtain patent licenses, in effect making
the program proprietary. To prevent this, we have made it clear
that any patent must be licensed for everyone's free use or not
licensed at all.
(Hereinafter, translation is included without limitation in the term
PRGL¿FDWLRQ(DFKOLFHQVHHLVDGGUHVVHGDV\RX
Activities other than copying, distribution and modification are
not covered by this License; they are outside its scope. The act
of running the Program is not restricted, and the output from the
Program is covered only if its contents constitute a work based
on the Program (independent of having been made by running
the Program). Whether that is true depends on what the Program
does.
These requirements apply to the modified work as a whole. If
identL¿DEOH sections of that work are not derived from the Program,
and can be reasonably considered independent and separate
works in themselves, then this License, and its terms, do not apply
to those sections when you distribute them as separate works.
But when you distribute the same sections as part of a whole
which is a work based on the Program, the distribution of the
whole must be on the terms of this License, whose permissions for
other licensees extend to the entire whole, and thus to each and
every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest
your rights to work written entirely by you; rather, the intent is
to exercise the right to control the distribution of derivative or
collective works based on the Program.
81
End User License Agreement for Operating System Software
In addition, mere aggregation of another work not based on the
Program with the Program (or with a work based on the Program)
on a volume of a storage or distribution medium does not bring the
other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on
it, under Section 2) in object code or executable form under the
terms of Sections 1 and 2 above provided that you also do one of
the following:
a) Accompany it with the complete corresponding machinereadable source code, which must be distributed under the
terms of Sections 1 and 2 above on a medium customarily
used for software interchange; or,
b) Accompany it with a written offer, valid for at least three
years, to give any third party, for a charge no more than
your cost of physically performing source distribution, a
complete machine-readable copy of the corresponding
source code, to be distributed under the terms of Sections
1 and 2 above on a medium customarily used for software
interchange; or,
c) Accompany it with the information you received as to
the offer to distribute corresponding source code. (This
alternative is allowed only for noncommercial distribution
and only if you received the program in object code
or executable form with such an offer, in accord with
Subsection b above.)
The source code for a work means the preferred form of the work
for making PRGL¿FDWLRQV to it. For an executable work, complete
source code means all the source code for all modules it contains,
plus any associated interface GH¿QLWLRQ ¿OHV plus the scripts used
to control compilation and installation of the executable. However,
as a special exception, the source code distributed need not
include anything that is normally distributed (in either source or
binary form) with the major components (compiler, kernel, and so
on) of the operating system on which the executable runs, unless
that component itself accompanies the executable.
If distribution of executable or object code is made by offering
access to copy from a designated place, then offering equivalent
access to copy the source code from the same place counts as
distribution of the source code, even though third parties are not
compelled to copy the source along with the object code.
License Agreements
4. You may not copy, modify, sublicense, or distribute the
Program except as expressly provided under this License. Any
attempt otherwise to copy, modify, sublicense or distribute the
Program is void, and will automatically terminate your rights under
this License. However, parties who have received copies, or rights,
from you under this License will not have their licenses terminated
so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not
signed it. However, nothing else grants you permission to modify
or distribute the Program or its derivative works. These actions
are prohibited by law if you do not accept this License. Therefore,
by modifying or distributing the Program (or any work based on
the Program), you indicate your acceptance of this License to
do so, and all its terms and conditions for copying, distributing or
modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based
on the Program), the recipient automatically receives a license
from the original licensor to copy, distribute or modify the Program
subject to these terms and conditions. You may not impose any
further restrictions on the recipients' exercise of the rights granted
herein. You are not responsible for enforcing compliance by third
parties to this License.
82
7. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement
or otherwise) that contradict the conditions of this License, they
do not excuse you from the conditions of this License. If you
cannot distribute so as to satisfy simultaneously your obligations
under this License and any other pertinent obligations, then as a
consequence you may not distribute the Program at all.
For example, if a patent license would not permit royalty-free
redistribution of the Program by all those who receive copies
directly or indirectly through you, then the only way you could
satisfy both it and this License would be torefrain entirely from
distribution of the Program. If any portion of this section is held
invalid or unenforceable underany particular circumstance, the
balance of the section is intended toapply and the section as a
whole is intended to apply in othercircumstances.
It is not the purpose of this section to induce you to infringe any
patents or other property right claims or to contest validity of
any such claims; this section has the sole purpose of protecting
the integrity of the free software distribution system, which is
implemented by public license practices. Many people have made
generous contributions to the wide range of software distributed
through that system in reliance on consistent application of that
system; it is up to the author/donor to decide if he or she is willing
to distribute software through any other system and a licensee
cannot impose that choice.
This section is intended to make thoroughly clear what is believed
to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in
certain countries either by patents or by copyrighted interfaces,
the original copyright holder who places the Program under this
License may add an explicit geographical distribution limitation
excluding those countries, so that distribution is permitted only in
or among countries not thus excluded. In such case, this License
incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or
new versions of the General Public License from time to time.
Such new versions will be similar in spirit to the present version,
but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the
Program VSHFL¿HV a version number of this License which applies
to it and "any later version", you have the option of following the
terms and conditions either of that version or of any later version
published by the Free Software Foundation. If the Program does
not specify a version number of this License, you may choose any
version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free
programs whose distribution conditions are different, write to the
author to ask for permission. For software which is copyrighted
by the Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for this. Our decision
will be guided by the two goals of preserving the free status of all
derivatives of our free software and of promoting the sharing and
reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF
CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM,
TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM
"AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
End User License Agreement for Operating System Software
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK
AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM
IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY
AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A
FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
You should also get your employer (if you work as a programmer)
or your school, if any, to sign a "copyright disclaimer" for the
program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the
program `Gnomovision' (which makes passes at compilers)
written by James Hacker.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating
your program into proprietary programs. If your program is a
subroutine library, you may consider it more useful to permit
linking proprietary applications with the library. If this is what you
want to do, use the GNU Library General Public License instead
of this License.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the
greatest possible use to the public, the best way to achieve this
is to make it free software which everyone can redistribute and
change under these terms.
To do so, attach the following notices to the program. It is safest
to attach them to the start of each source ¿le to most effectively
convey the exclusion of warranty; and each file should have at
least the "copyright" line and a pointer to where the full notice is
found.
<one line to give the program's name and a brief idea of what
it does.>
Copyright © <year> <name of author>
License Agreements
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
as published by the Free Software Foundation; either version
2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE. See the GNU General Public
License for more details.
You should have received a copy of the GNU General Public
License along with this program; if not, write to the Free
Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
MA 02110-1301 USA
Also add information on how to contact you by electronic and
paper mail.
If the program is interactive, make it output a short notice like this
when it starts in an interactive mode:
Gnomovision version 69, Copyright © year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY;
for details type `show w'. This is free software, and you are
welcome to redistribute it under certain conditions; type `show
c' for details.
The hypothetical commands `show w' and `show c' should show
the appropriate parts of the General Public License. Of course,
the commands you use may be called something other than `show
w' and `show c'; they could even be mouse-clicks or menu items-whatever suits your program.
83
End User License Agreement for Operating System Software
GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999
Copyright © 1991, 1999 Free Software Foundation, Inc. 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
[This is the ¿UVW released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence
the version number 2.1.]
Preamble
The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General
Public Licenses are intended to guarantee your freedom to share
and change free software--to make sure the software is free for all
its users.
This license, the Lesser General Public License, applies to some
specially designated software packages--typically libraries--of
the Free Software Foundation and other authors who decide to
use it. You can use it too, but we suggest you ¿UVW think carefully
about whether this license or the ordinary General Public License
is the better strategy to use in any particular case, based on the
explanations below.
When we speak of free software, we are referring to freedom
of use, not price. Our General Public Licenses are designed to
make sure that you have the freedom to distribute copies of free
software (and charge for this service if you wish); that you receive
source code or can get it if you want it; that you can change the
software and use pieces of it in new free programs; and that you
are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid
distributors to deny you these rights or to ask you to surrender
these rights. These restrictions translate to certain responsibilities
for you if you distribute copies of the library or if you modify it.
License Agreements
For example, if you distribute copies of the library, whether gratis
or for a fee, you must give the recipients all the rights that we
gave you. You must make sure that they, too, receive or can get
the source code. If you link other code with the library, you must
provide complete object files to the recipients, so that they can
relink them with the library after making changes to the library and
recompiling it. And you must show them these terms so they know
their rights.
We call this license the "Lesser" General Public License
because it does Less to protect the user's freedom than the
ordinary General Public License. It also provides other free
software developers Less of an advantage over competing nonfree programs. These disadvantages are the reason we use the
ordinary General Public License for many libraries. However,
the Lesser license provides advantages in certain special
circumstances.
For example, on rare occasions, there may be a special need to
encourage the widest possible use of a certain library, so that it
becomes a de-facto standard. To achieve this, non-free programs
must be allowed to use the library. A more frequent case is that a
free library does the same job as widely used non-free libraries.
In this case, there is little to gain by limiting the free library to free
software only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use a large
body of free software. For example, permission to use the GNU
C Library in non-free programs enables many more people to use
the whole GNU operating system, as well as its variant, the GNU/
Linux operating system.
Although the Lesser General Public License is Less protective of
the users' freedom, it does ensure that the user of a program that
is linked with the Library has the freedom and the wherewithal to
UXQWKDWSURJUDPXVLQJDPRGL¿HGYHUVLRQRIWKH/LEUDUy.
We protect your rights with a two-step method: (1) we copyright
the library, and (2) we offer you this license, which gives you legal
permission to copy, distribute and/or modify the library.
The precise terms and conditions for copying, distribution and
PRGL¿FDWLRQ follow. Pay close attention to the difference between
a "work based on the library" and a "work that uses the library".
The former contains code derived from the library, whereas the
latter must be combined with the library in order to run.
To protect each distributor, we want to make it very clear that
there is no warranty for the free library. Also, if the library is
modi¿ed by someone else and passed on, the recipients should
know that what they have is not the original version, so that the
original author's reputation will not be affected by problems that
might be introduced by others.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
Finally, software patents pose a constant threat to the existence
of any free program. We wish to make sure that a company
cannot effectively restrict the users of a free program by obtaining
a restrictive license from a patent holder. Therefore, we insist that
any patent license obtained for a version of the library must be
FRQVLVWHQWZLWKWKHIXOOIUHHGRPRIXVHVSHFL¿HGLQWKLVOLFHQVH
Most GNU software, including some libraries, is covered by the
ordinary GNU General Public License. This license, the GNU
Lesser General Public License, applies to certain designated
libraries, and is quite different from the ordinary General Public
License. We use this license for certain libraries in order to permit
linking those libraries into non-free programs.
84
When a program is linked with a library, whether statically
or using a shared library, the combination of the two is legally
speaking a combined work, a derivative of the original library. The
ordinary General Public License therefore permits such linking
only if the entire combination fits its criteria of freedom. The
Lesser General Public License permits more lax criteria for linking
other code with the library.
0. This License Agreement applies to any software library or
other program which contains a notice placed by the copyright
holder or other authorized party saying it may be distributed under
the terms of this Lesser General Public License (also called "this
License"). Each licensee is addressed as "you".
A "library" means a collection of software functions and/or data
prepared so as to be conveniently linked with application programs
(which use some of those functions and data) to form executables.
The "Library", below, refers to any such software library or work
which has been distributed under these terms. A "work based on
the Library" means either the Library or any derivative work under
copyright law: that is to say, a work containing the Library or a
portion of it, either verbatim or with PRGL¿FDWLRQV and/or translated
End User License Agreement for Operating System Software
straightforwardly into another language. (Hereinafter, translation
LVLQFOXGHGZLWKRXWOLPLWDWLRQLQWKHWHUPPRGL¿FDWLRQ
to exercise the right to control the distribution of derivative or
collective works based on the Library.
"Source code" for a work means the preferred form of the work
for making PRGL¿FDWLRQV to it. For a library, complete source code
means all the source code for all modules it contains, plus any
associated interface GH¿QLWLRQ ¿OHV plus the scripts used to control
compilation and installation of the library.
In addition, mere aggregation of another work not based on the
Library with the Library (or with a work based on the LibraU\ on
a volume of a storage or distribution medium does not bring the
other work under the scope of this License.
Activities other than copying, distribution and modification are
not covered by this License; they are outside its scope. The act of
running a program using the Library is not restricted, and output
from such a program is covered only if its contents constitute a
work based on the Library (independent of the use of the Library
in a tool for writing LW Whether that is true depends on what the
Library does and what the program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library's
complete source code as you receive it, in any medium, provided
that you conspicuously and appropriately publish on each copy
an appropriate copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this License and to the absence
of any warranty; and distribute a copy of this License along with
the Library.
You may charge a fee for the physical act of transferring a copy,
and you may at your option offer warranty protection in exchange
for a fee.
2. You may modify your copy or copies of the Library or any
portion of it, thus forming a work based on the Library, and
copy and distribute such modifications or work under the terms
of Section 1 above, provided that you also meet all of these
conditions:
D 7KHPRGL¿HGZRUNPXVWLWVHOIEHDVRIWZDUHOLEUDUy.
E You must cause the files modified to carry prominent
notices stating that you changed the ¿OHV and the date of
any change.
F You must cause the whole of the work to be licensed at no
charge to all third parties under the terms of this License.
These requirements apply to the modified work as a whole. If
GHQWL¿DEOH sections of that work are not derived from the Library,
and can be reasonably considered independent and separate
works in themselves, then this License, and its terms, do not apply
to those sections when you distribute them as separate works.
But when you distribute the same sections as part of a whole
which is a work based on the Library, the distribution of the whole
must be on the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each and every
part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest
your rights to work written entirely by you; rather, the intent is
Once this change is made in a given copy, it is irreversible for
that copy, so the ordinary GNU General Public License applies to
all subsequent copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of
the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or
derivative of it, under Section in object code or executable
form under the terms of Sections 1 and 2 above provided that
you accompany it with the complete corresponding machinereadable source code, which must be distributed under the terms
of Sections 1 and 2 above on a medium customarily used for
software interchange.
If distribution of object code is made by offering access to copy
from a designated place, then offering equivalent access to copy
the source code from the same place satisfies the requirement
to distribute the source code, even though third parties are not
compelled to copy the source along with the object code.
5. A program that contains no derivative of any portion of the
Library, but is designed to work with the Library by being compiled
or linked with it, is called a "work that uses the Library". Such
a work, in isolation, is not a derivative work of the Library, and
therefore falls outside the scope of this License.
However, linking a "work that uses the Library" with the Library
creates an executable that is a derivative of the Library (because
it contains portions of the Library, rather than a "work that uses
the library". The executable is therefore covered by this License.
Section 6 states terms for distribution of such executables.
When a "work that uses the Library" uses material from a header
¿OH that is part of the Library, the object code for the work may be
a derivative work of the Library even though the source code is
not. Whether this is true is especially significant if the work can
be linked without the Library, or if the work is itself a library. The
WKUHVKROGIRUWKLVWREHWUXHLVQRWSUHFLVHO\GH¿QHGE\ODw.
License Agreements
GIf a facility in the PRGL¿HG Library refers to a function or a
table of data to be supplied by an application program that
uses the facility, other than as an argument passed when
the facility is invoked, then you must make a good faith
effort to ensure that, in the event an application does not
supply such function or table, the facility still operates, and
performs whatever part of its purpose remains meaningful.
(For example, a function in a library to compute square
roots has a purpose that is entirely well-de¿Qed independent
of the application. Therefore, Subsection 2d requires that
any application-supplied function or table used by this
function must be optional: if the application does not supply
LWWKHVTXDUHURRWIXQFWLRQPXVWVWLOOFRPSXWHVTXDUHURRWV
3. You may opt to apply the terms of the ordinary GNU General
Public License instead of this License to a given copy of the
Library. To do this, you must alter all the notices that refer to this
License, so that they refer to the ordinary GNU General Public
License, version 2, instead of to this License. (If a newer version
than version 2 of the ordinary GNU General Public License has
appe ared, then you ca n speci fy that versio n instead if you wi sh.
Do not make any other change in these notices.
If such an object file uses only numerical parameters, data
structure layouts and accessors, and small macros and small
inline functions (ten lines or less in lHQJWK then the use of the
object file is unrestricted, regardless of whether it is legally a
derivative work. (Executables containing this object code plus
SRUWLRQVRIWKH/LEUDU\ZLOOVWLOOIDOOXQGHU6HFWLRQ
Otherwise, if the work is a derivative of the Library, you may
distribute the object code for the work under the terms of Section
6. Any executables containing that work also fall under Section 6,
whether or not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine
or link a "work that uses the Library" with the Library to produce
85
End User License Agreement for Operating System Software
a work containing portions of the Library, and distribute that
work under terms of your choice, provided that the terms permit
PRGL¿FDtion of the work for the customer's own use and reverse
HQJLQHHULQJIRUGHEXJJLQJVXFKPRGL¿FDWLRQV
You must give prominent notice with each copy of the work
that the Library is used in it and that the Library and its use are
covered by this /LFHQVH You must supply a copy of this /LFHQVH
If the work during execution displays copyright notices, you must
include the copyright notice for the Library among them, as well
as a reference directing the user to the copy of this /LFHQVH Also,
you must do one of these things:
a) Accompany the work with the complete corresponding
machine-readable source code for the Library including
whatever changes were used in the work (which must be
distributed under Sections 1 and 2 above); and, if the work
is an executable linked with the Library, with the complete
machine-readable "work that uses the Library", as object
code and/or source code, so that the user can modify the
Library and then relink to produce a modified executable
containing the modified Library (It is understood that
the user who changes the contents of definitions files in
the Library will not necessarily be able to recompile the
DSSOLFDWLRQWRXVHWKHPRGL¿HGGH¿QLWLRQV
b) Use a suitable shared library mechanism for linking with
the Library A suitable mechanism is one that (1) uses at
run time a copy of the library already present on the user's
computer system, rather than copying library functions into
the executable, and (2) will operate properly with a PRGL¿HG
version of the library, if the user installs one, as long as the
modified version is interface-compatible with the version
WKDWWKHZRUNZDVPDGHZLWK
c) Accompany the work with a written offer, valid for at least
three years, to give the same user the materials VSHFL¿HG in
Subsection 6a, above, for a charge no more than the cost of
SHUIRUPLQJWKLVGLVWULEXWLRQ
d) If distribution of the work is made by offering access to copy
from a designated place, offer equivalent access to copy
WKHDERYHVSHFL¿HGPDWHULDOVIURPWKHVDPHSODFH
e) Verify that the user has already received a copy of these
materials or that you have already sent this user a copy
License Agreements
For an executable, the required form of the "work that uses
the Library" must include any data and utility programs needed
for reproducing the executable from iW However, as a special
exception, the materials to be distributed need not include
anything that is normally distributed (in either source or binary
form) with the major components (compiler, kernel, and so on) of
the operating system on which the executable runs, unless that
FRPSRQHQWLWVHOIDFFRPSDQLHVWKHH[HFXWDEOH
It may happen that this requirement contradicts the license
restrictions of other proprietary libraries that do not normally
accompany the operating V\VWHP Such a contradiction means
you cannot use both them and the Library together in an
H[HFXWDEOHWKDW\RXGLVWULEXWH
You may place library facilities that are a work based on
the Library side-by-side in a single library together with other
library facilities not covered by this License, and distribute such
a combined library, provided that the separate distribution of the
work based on the Library and of the other library facilities is
otherwise permitted, and provided that you do these two things:
a) Accompany the combined library with a copy of the same
work based on the Library, uncombined with any other
library IDFLOLWLHV This must be distributed under the terms of
86
WKH6HFWLRQVDERYH
b) Give prominent notice with the combined library of the fact
that part of it is a work based on the Library, and explaining
where to find the accompanying uncombined form of the
VDPHZRUN
8 You may not copy, modify, sublicense, link with, or distribute
the Library except as expressly provided under this License
Any attempt otherwise to copy, modify, sublicense, link with, or
distribute the Library is void, and will automatically terminate your
rights under this LiFHQVH However, parties who have received
copies, or rights, from you under this License will not have
their licenses terminated so long as such parties remain in full
FRPSOLDQFH
9 You are not required to accept this License, since you have not
signed LW However, nothing else grants you permission to modify
or distribute the Library or its derivative ZRUNV These actions are
prohibited by law if you do not accept this LiFHQVH Therefore,
by modifying or distributing the Library (or any work based on
the Library), you indicate your acceptance of this License to do
so, and all its terms and conditions for copying, distributing or
PRGLI\LQJWKH/LEUDU\RUZRUNVEDVHGRQLW
Each time you redistribute the Library (or any work based on
the Library), the recipient automatically receives a license from the
original licensor to copy, distribute, link with or modify the Library
subject to these terms and conditions You may not impose any
further restrictions on the recipients' exercise of the rights granted
hereiQ You are not responsible for enforcing compliance by third
SDUWLHVZLWKWKLV/LFHQVH
11 If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to patent
issues), conditions are imposed on you (whether by court order,
agreement or otherwise) that contradict the conditions of this
License, they do not excuse you from the conditions of this
License If you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other pertinent
obligations, then as a consequence you may not distribute the
Library at all For example, if a patent license would not permit
royalty-free redistribution of the Library by all those who receive
copies directly or indirectly through you, then the only way you
could satisfy both it and this License would be to refrain entirely
from distribution of the Library
If any portion of this section is held invalid or unenforceable under
any particular circumstance, the balance of the section is intended
to apply, and the section as a whole is intended to apply in other
FLUFXPVWDQFHV
It is not the purpose of this section to induce you to infringe any
patents or other property right claims or to contest validity of
any such claims; this section has the sole purpose of protecting
the integrity of the free software distribution system which is
LPSOHPHQWHGE\SXEOLFOLFHQVHSUDFWLFHV0DQ\SHRSOHKDYHPDGH
generous contributions to the wide range of software distributed
through that system in reliance on consistent application of that
system; it is up to the author/donor to decide if he or she is willing
to distribute software through any other system and a licensee
FDQQRWLPSRVHWKDWFKRLFH
This section is intended to make thoroughly clear what is
EHOLHYHGWREHDFRQVHTXHQFHRIWKHUHVWRIWKLV/LFHQVH
12 If the distribution and/or use of the Library is restricted in
certain countries either by patents or by copyrighted interfaces,
the original copyright holder who places the Library under this
License may add an explicit geographical distribution limitation
excluding those countries, so that distribution is permitted only in
End User License Agreement for Operating System Software
or among countries not thus excluded. In such case, this License
incorporates the limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or
new versions of the Lesser General Public License from time
to time. Such new versions will be similar in spirit to the present
version, but may differ in detail to address new problems or
concerns. Each version is given a distinguishing version number.
If the Library specifies a version number of this License which
applies to it and "any later version", you have the option of
following the terms and conditions either of that version or of
any later version published by the Free Software Foundation.
If the Library does not specify a license version number, you
may choose any version ever published by the Free Software
Foundation.
14. If you wish to incorporate parts of the Library into other free
programs whose distribution conditions are incompatible with
these, write to the author to ask for permission. For software
which is copyrighted by the Free Software Foundation, write to the
Free Software Foundation; we sometimes make exceptions for
this. Our decision will be guided by the two goals of preserving the
free status of all derivatives of our free software and of promoting
the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF
CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO
THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY
"AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK
AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY
IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
<one line to give the library's name and a brief idea of what it
does.>
Copyright © <year> <name of author>
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE. See the GNU Lesser General
Public License for more details.
You should have received a copy of the GNU Lesser General
Public License along with this library; if not, write to the Free
Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
MA 02110-1301 USA
Also add information on how to contact you by electronic and
paper mail.
You should also get your employer (if you work as a programmer)
or your school, if any, to sign a "copyright disclaimer" for the
library, if necessary. Here is a sample; alter the names: Yoyodyne,
Inc., hereby disclaims all copyright interest in the library `Frob' (a
library for tweaking knobs) written by James Random Hacker.
<signature of Ty Coon>, 1 April 1990
Ty Coon, President of Vice
That's all there is to it!
License Agreements
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA
OR DATA BEING RENDERED INACCURATE OR LOSSES
SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest
possible use to the public, we recommend making it free software
that everyone can redistribute and change. You can do so by
permitting redistribution under these terms (or, alternatively, under
the terms of the ordinary General Public License).
To apply these terms, attach the following notices to the library.
It is safest to attach them to the start of each source ¿le to most
effectively convey the exclusion of warranty; and each ¿OH should
have at least the "copyright" line and a pointer to where the full
notice is found.
87
Appendixes
Appendix A:
Picture Format for Each Input Source
Aspect Specifications
Yes : Selectable
Auto
Aspect
S ignal
As pect
V ideo ID
16:9
Standard 1
16:9
Standard 2
16:9
Zoom
4:3
Standard
4:3
Ex panded
4:3
Zoom 1
4:3
Zoom 2
Y es
Ye s
Y es
Y es
V ideo
NT S C
No
4x3
Y es
No
Ye s
ANT
Y C BC R
480p
No
16x 9
Y es
No
Ye s
No
Ye s
No
No
480i
No
4x3
No
No
No
Ye s
Ye s
Y es
Y es
Y P BP R
1080i/720p
No
16x9
Y es
Ye s
Ye s
No
Ye s
No
No
HDMI
1080i/720p
No
16x9
Y es
Ye s
Ye s
No
Ye s
No
No
480p
Auto ON
16x 9
Y es Initial
No
Ye s
No
No
No
No
Letter
No
No
No
Ye s
Y es
Ye s Initial
Ye s
4x3
No
No
No
Ye s
Y es Initial
Y es
Ye s
No Info
Y es
No
Ye s
Y es
Ye s
Y es
Y es
Y es
Input 1
480i
Video
NTSC
Auto OF F
No
Ye s
No
Ye s
Y es
Ye s
Y es
Auto ON
16x 9
Y es Initial
No
Ye s
No
No
No
No
Letter
No
No
No
Ye s
Y es
Ye s Initial
Ye s
No
No
Ye s
Y es Initial
Y es
Ye s
No
Ye s
Y es
Ye s
Y es
Y es
S -V ideo
Input 2
HDMI
4x3
No
No ID
Y es
Auto OF F
No
Ye s
No
Ye s
Y es
Ye s
Y es
Y es
1080i/720p
No
16x9
Y es
Ye s
Ye s
No
Ye s
No
No
480p
Auto ON
16x 9
Y es Initial
No
Ye s
No
No
No
No
Letter
No
No
No
Ye s
Y es
Ye s Initial
Ye s
4x3
No
No
No
Ye s
Y es Initial
Y es
Ye s
No Info
Y es
No
Ye s
Y es
Ye s
Y es
Y es
Y es
480i
Video
NTSC
Auto OF F
No
Ye s
No
Ye s
Y es
Ye s
Y es
Auto ON
16x 9
Y es Initial
No
Ye s
No
No
No
No
Letter
No
No
No
Ye s
Y es
Ye s Initial
Ye s
4x3
No
No
No
Ye s
Y es Initial
Y es
Ye s
No ID
Y es
No
Ye s
Y es
Ye s
Y es
Y es
S -V ideo
Input 3
Y P BP R
Auto OF F
No
Ye s
No
Ye s
Y es
Ye s
Y es
Y es
1080i/720p
No
16x9
Y es
Ye s
Ye s
No
Ye s
No
No
480p
Auto ON
16x 9
Y es Initial
No
Ye s
No
No
No
No
Letter
No
No
No
Ye s
Y es
Ye s Initial
Ye s
4x3
No
No
No
Ye s
Y es Initial
Y es
Ye s
No ID
Y es
No
Ye s
Y es
Ye s
Y es
Y es
480i
Appendixes
Aspect
ANT
Analog
Digital
Auto OF F
Video
No
No Signal
No
No
NTSC
Auto ON
16x 9
Y es Initial
No
Ye s
No
No
No
No
Letter
No
No
No
Ye s
Y es
Ye s Initial
Ye s
4x3
No
No
No
Ye s
Y es Initial
Y es
Ye s
No ID
Y es
No
Ye s
Y es
Ye s
Y es
Y es
Auto OF F
88
No : Un - Selectable
Input
No
Appendixes
Aspect Specifications
Yes : Selectable
(Continuation)
Input 4
Input
Auto
Aspect
S ignal
As pect
V ideo ID
Y P BP R
Input 5
HDMI
Y P BP R
16:9
Standard 2
16:9
Zoom
4:3
Standard
4:3
Ex panded
4:3
Zoom 1
4:3
Zoom 2
No
16x 9
Y es
Y es
Y es
No
Ye s
No
No
480p
Auto ON
16x9
Y es Initial
No
Ye s
No
No
No
No
Letter
No
No
No
Ye s
Ye s
Y es Initial
Y es
Y es Initial
Ye s
Ye s
Ye s
Ye s
Y es
4x3
No
No
No
Ye s
No ID
Y es
No
Ye s
Y es
16x9
Y es Initial
No
Ye s
No
No
No
No
Letter
No
No
No
Ye s
Ye s
Y es Initial
Y es
4x3
No
No
No
Ye s
Y es Initial
Ye s
Ye s
No ID
Y es
No
Ye s
Y es
Ye s
Ye s
Y es
Auto OF F
No
No Signal
No
No
NT S C
Auto ON
Auto OF F
No
1080i/720p
No
16x9
Ye s
Y es
Y es
No
Ye s
No
No
480p
480i
Auto ON
16x 9
Y es Initial
No
Ye s
No
No
No
No
Letter
No
No
No
Ye s
Ye s
Y es Initial
Y es
4x3
No
No
No
Ye s
Y es Initial
Ye s
Ye s
No Info
Y es
No
Ye s
Y es
Ye s
Ye s
Y es
Auto OF F
No
Ye s
No
Ye s
Y es
Ye s
Ye s
Y es
1080i/720p
No
16x9
Ye s
Y es
Y es
No
Ye s
No
No
480p
480i
Auto ON
16x 9
Y es Initial
No
Ye s
No
No
No
No
Letter
No
No
No
Ye s
Ye s
Y es Initial
Y es
4x3
No
No
No
Ye s
Y es Initial
Ye s
Ye s
No ID
Y es
No
Ye s
Y es
Ye s
Ye s
Y es
Auto OF F
V ideo
16:9
Standard 1
1080i/720p
480i
V ideo
No : Un - Selectable
Aspect
No
No Signal
No
No
NT S C
Auto ON
16x9
Y es Initial
No
Ye s
No
No
No
No
Letter
No
No
No
Ye s
Ye s
Y es Initial
Y es
4x3
No
No
No
Ye s
Y es Initial
Ye s
Ye s
No ID
Y es
No
Ye s
Y es
Ye s
Ye s
Y es
Auto OF F
No
Appendixes
89
Index
A
Accessories, . . . . . . . . . . . . . . . . . . . . . . . . . .4
Antennas (Connecting), . . . . . . . . . . . . . . . . .7
Aspect Ratio, . . . . . . . . . . . . . . . . . . . . .25, 46
Audio
Bass Boost . . . . . . . . . . . . . . . . . . . . . . . .47
Audio Settings . . . . . . . . . . . . . . . . . . . . . . .48
Audio Source . . . . . . . . . . . . . . . . . . . . . . . .48
Auto Noise Cancel . . . . . . . . . . . . . . . . . . . . .48
Menu Preference
Language . . . . . . . . . . . . . . . . . . . . . . . . . .62
Background . . . . . . . . . . . . . . . . . . . . . . . .63
Monitor Out . . . . . . . . . . . . . . . . . . . . . . . . . .66
N
Noise Cancel . . . . . . . . . . . . . . . . . . . . . . . . .48
Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Bass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Black Enhancement . . . . . . . . . . . . . . . . . . . .44
Black Side Panel . . . . . . . . . . . . . . . . . . . . . .45
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . .43
P
CableCARD . . . . . . . . . . . . . . . . . . . . . . . . . .67
Caution and Safety Tips . . . . . . . . . . . . . . . .2-3
Channel Manager . . . . . . . . . . . . . . . . . . .52-53
Auto Channel Scan . . . . . . . . . . . . . . . . . . .52
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Closed Captions
Captions . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Color Temperature . . . . . . . . . . . . . . . . . . . . .44
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Contrast Mode . . . . . . . . . . . . . . . . . . . . . . . .44
Perfect Volume . . . . . . . . . . . . . . . . . . . . . . .48
Photo Input . . . . . . . . . . . . . . . . . . . . . . . . . .27
Picture Mode . . . . . . . . . . . . . . . . . . . . . . . .43
Picture-in-Pictur e (PIP) . . . . . . . . . . . . . .30-32
Power Swivel . . . . . . . . . . . . . . . . . . . . . .5,8,69
R
Remote Control
Functions . . . . . . . . . . . . . . . . . . . . . . . .23-40
Programming Codes . . . . . . . . . . . . . . .39-40
Installing Batteries . . . . . . . . . . . . . . . . . . . .4
S
External Video Source . . . . . . . . . . . . . . .18-22
Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . .63
Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Connecting External Speakers . . . . . . . . . .21
Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Split Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
F
T
Favorite Channel . . . . . . . . . . . . . . . . . . . . . .29
Freeze . . . . . . . . . . . . . . . . . . . . . . . . . . . 24,32
Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Tint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Treble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
TV Guide On ScreenTM . . . . . . . . . . . . . .49-51
E
H
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15,19
I
Input Setup . . . . . . . . . . . . . . . . . . . . . . .24,64
L
Language
Menu Language . . . . . . . . . . . . . . . . . . . . ..62
Locks
Change Access Code . . . . . . . . . . . . . . . . 54
Channel Lock . . . . . . . . . . . . . . . . . . . . . . .54
Front Panel Lock . . . . . . . . . . . . . . . . . . . .54
Movie Ratings . . . . . . . . . . . . . . . . . . . . . . .55
TV Ratings . . . . . . . . . . . . . . . . . . . . . . . . .56
TV Ratings (Canadian - English) . . . . . . . . .57
Index
M
B
C
90
TV Ratings (Canadian - French) . . . . . . . . .58
Alternate Ratings
.
U.S. . . . . . . . . . . . . . . . . .59
V
Video Settings . . . . . . . . . . . . . . . . . . . . .43-46
W
White Balance . . . . . . . . . . . . . . . . . . . . . . . .45
Notes
91
Notes
92
Notes
93
Notes
94
Notes
95
QR68671