Intel CV700A Network Card User Manual

Add to my manuals
63 Pages

advertisement

Intel CV700A Network Card User Manual | Manualzz
CV700A / CV702A
400MHz FSB / VGA / LAN / Sound
400MHz FSB . All-in-one
Sound . 3 LAN
SATA150 . ATA 33/66/100 . USB . IrDA . CF
Multi- LAN Board
NO.CV700A / CV702A
Release date: OCT.26.2006
Contents
CV700A / CV702A
CHAPTER 1 GENERAL INFORMATION ........................................................................ 1
1-1 MAJOR FEATURE........................................................................................................ 2
1-2 SPECIFICATION .......................................................................................................... 3
1-3 HARDWARE NOTICE GUIDE ..................................................................................... 4
1-3-1 INSTALLING THE MINI PCI CARD.......................................................................... 6
1-3-3.1 REMOVING THE MINI PCI CARD........................................................................ 8
1-4 PACKING LIST*............................................................................................................ 9
CHAPTER 2 HARDWARE INSTALLATION ................................................................... 10
2-1 UNPACKING PRECAUTION .......................................................................................10
2-2 UNPACKING CHECKUP ............................................................................................. 11
2-3 DIMENSION ................................................................................................................ 12
2-4 LAYOUT ...................................................................................................................... 13
2-5 DIAGRAM ................................................................................................................... 14
2-5-1 BOTTOM SIDE DIAGRAM / BACK PANEL.............................................................. 15
2-6 INSTALL MEMORY .................................................................................................... 16
2-7 LIST OF JUMPERS .................................................................................................... 17
2-8 JUMPER SETTING DESCRIPTION .......................................................................... 18
2-9 CMOS DATA SET ....................................................................................................... 18
2-10 JCF2 CF CARD POWER VOLTAGE SELECT ......................................................... 19
2-11 JCF1 CF CARD MASTER/ SLAVE SELECT ........................................................... 20
CHAPTER 3 CONNECTION ........................................................................................ 21
3-1 LIST OF CONNECTORS............................................................................................ 21
3-2 FAN CONNECTOR ..................................................................................................... 22
3-3 IDE CONNECTORS ................................................................................................... 22
3-4 COMPACT-FLASH MEMORY SOCKET .................................................................... 24
3-5 PARALLEL PORT CONNECTOR .............................................................................. 25
3-6 SERIAL PORT CONNECTOR ................................................................................... 26
3-7 KEYBOARD AND MOUSE CONNECTOR ................................................................ 27
3-8 USB PORT / HEADER ............................................................................................... 28
3-9 IR CONNECTOR ....................................................................................................... 29
3-10 VGA CONNECTOR ................................................................................................. 29
3-10.1 VGA HEADER ...................................................................................................... 29
3-11 LAN PORT ............................................................................................................... 30
3-12 AUDIO PORT CONNECTOR .................................................................................. 31
3-13 DC 12V IN AND DC OUT ........................................................................................ 32
i
3-14 DC +5/+12V OUTPUT CONNECTOR....................................................................... 32
3-15 SERIAL ATA .............................................................................................................. 33
3-16 I 2 C BUS CONNECTOR ............................................................................................ 33
3-17 TV-OUT CONNECTOR ............................................................................................ 34
3-18 FRONT-PANEL ......................................................................................................... 34
CHAPTER 4 INTRODUCTION OF BIOS...................................................................... 35
4-1 ENTER SETUP .......................................................................................................... 35
4-2 GETTING HELP ......................................................................................................... 36
4-3 THE MAIN MENU ....................................................................................................... 36
4-4 STANDARD CMOS FEATURES ................................................................................ 38
4-5 ADVANCED BIOS FEATURES .................................................................................. 39
4-6 ADVANCED CHIPSET FEATURES ........................................................................... 40
4-6-1 DRAM CLOCK / DRIVE CONTROL ........................................................................ 40
4-6-2 AGP & P2P BRIDGE CONTROL ............................................................................. 41
4-7 INTEGRATED PERIPHERALS .................................................................................. 41
4-7-1 VIA OnCHIP IDE DEVICE ....................................................................................... 42
4-7-2 VIA OnCHIP PCI DEVICE ...................................................................................... 42
4-7-3 SUPER IO DEVICE ................................................................................................. 43
4-8 POWER MANAGEMENT SETUP .............................................................................. 43
4-8-1 IRQ / EVENT ACTIVITY DETECT ........................................................................... 44
4-8-1.1 IRQs ACTIVITY MONITORING ............................................................................ 44
4-9 PnP / PCI CONFIGURATION SETUP ........................................................................ 45
4-10 PC HEALTH STATUS ............................................................................................... 46
4-11 FREQUENCY / VOLTAGE CONTROL ..................................................................... 47
4-12 LOAD FAIL-SAFE / OPTIMIZED DEFAULTS ........................................................... 47
4-13 SET SUPERVISOR / USER PASSWORD ............................................................... 48
CHAPTER 5 DRIVER INSTALLATION........................................................................ 49
5-1 VIA 4 IN 1 INSTALL VIA IDE/AGP/INF DRIVER ....................................................... 51
5-2 VGA INSTALL CN700 VGA DRIVER .......................................................................... 53
5-3 SOUND INSTALL VIA AUDIO CODEC DRIVER FOR VIA ..................................... 54
5-4 USB2.0 INSTALL VIA USB2.0 INSTALLING DRIVER................................................ 55
5-5 HOW TO DISABLE ON-BOARD SOUND .................................................................. 56
5-6 HOW TO UPDATE BIOS ............................................................................................ 56
APPENDIX A: POWER CONSUMPTION TEST................................................................ 57
APPENDIX B: RESOLUTION LIST.................................................................................... 57
WARNING ......................................................................................................................... 58
ii
2006
OCT . 26 . 2006
Chapter-1
General lnformation
The CV700A is a Light form factor All-In-One Multimedia control Board. The board design
combines all necessary input and output effects interfaces, which makes itself an ideal
all-in-one control board for Networking Application. The board is designed
with 400 MHz internal bus clock rate architecture.
The CV700A All-In-One motherboard uses VIA CN700 ( CN700 and VT8237R Plus) chipset,
built-in VIA Eden(V4) / C7(V4) EBGA CPU, VGA and Audio feature onboard and supports ,
built-in multi-LAN options . The board is also designed with
AC97 2.1 sound interface which provides an ideal sound adapter in any audio
application. This board offers the superb performance and PC specification in the industry.
The motherboard is fully compatible with industry standards, adding many technical
enhancements, and is fully compatible with thousands of software applications developed
for IBM PC/AT compatible computers. The control logic provides high-speed performance
for the most advanced multiuser, multitasking applications available today.
With DMA33/66/100 and SATA150 access of mode 4 to IDE drive interface architecture,
the IDE interface supports maximum 100 MB/sec ( IDE) and 150 MB/sec (SATA) data
transfer rate to 2 pieces of IDE drive connection and 1 piece of SATA Driver connection.
Compact Flash Reader supports IDE/ ATA interface.
A single Flash chip holds the system BIOS, and you can change the Flash BIOS by the
Utility Update. Advanced IR port also provides a faster data transmission.
CV700A board is designed with CN700 intergrated graphic VGA controller which provides
connection to VGA Monitor . VGA Controller is 128-bit single cycle 2D/3D graphic engine
which supports up to 1600x1200 extended screen resolutions and also real time DVD
MPEG-2 and AC3 playback.
The CV700A Board supports DDR2 RAM memory with one unbuffered double-sided
DIMMs up to 1GB
1
1-1 Major Feature
1. VIA Eden (V4) nano BGA2 500MHz CPU/ VIA C7 nano BGA2 1GHz CPU
2. VIA CN700 chipset (CN700 + VT8237R Plus)
3. One DDR2 400/533 DRAM unbuffered double-sided DIMMs up to 1GB
4. Dual channel master mode PCI support four IDE disk drives DMA 33/66/100 controller
One Channle SATA 150 Connector
5. 400 MHz system clock support
6. Versatile storage device:
*
One 50-pin Compact Flash socket
*
One 40-pin DOM
*
One 2.5" HDD
*
One SATA HDD
7. On board CN700 graphic controller integrated graphics
8. On board multi-LAN option*:
*
CV700A-3R ----3 x Realtek 8100C 10/100 Mb
*
CV700A-3G ----3 x Realtek 8110SC 10/100/1000 Mb
*
CV700A-3U ----3 x Intel 82541GI/PI/ER 10/100/1000 Mb
9. Compact Flash Reader Type I/II for IDE/ATA interface
10. Two serial RS232 Ports
11. One enhanced bi-directional parallel ports (SPP/ECP/EPP)
12. On board mini PS/2 Keyboard/Mouse connector
13. On board Sound, AC97 2.1
14. DC 12V-IN Power Adapter support
*The models mentioned above are standard models currently.
The multi-LAN option might change due to customization.
2
1-2 Specification
1.CPU: VIA Eden (V4) nano BGA2 500 MHZ CPU / VIA C7 (V4) nano BGA2 1GHz CPU
2. Cache Memory: Integrated full-speed 128KB L1/L2 cache
3.Chipset: VIA CN700 (North:CN700 ;South:VT8237R Plus)
4. Memory: One DIMM socket up to 1GB DDR2 400/533 DRAM
5. VGA: CN700 integrated graphic controller ; support 128-bit 2D/3D display up to
1600x1200, memory sharable up to 64MB
6. I/O Chipset: VIA VT1211IO
7. IDE: four IDE disk drives; support DMA33/66/100 transfer rate up to 33/66/100 MB/sec
SATA : 1 SATA disk drivers ; support SATA150 MB/sec
8. LAN: * CV700A-3R ----3 x Realtek 8100C 10/100 Mb ( Wake-On-Lan) for LAN1
* CV700A-3G ----3 x Realtek 8110SC 10/100/1000 Mb
* CV700A-3U ----3 x Intel 82541GI/PI/ER 10/100/1000 Mb
9. Storage devices: * One 50-pin Compact Flash socket
* One 40-pin DOM
* One 2.5" HDD
* One SATA HDD
10. Parallel Port: 1 parallel port ; Support SPP/ECP/EPP
11. Serial Port: Two serial ports ; Support RS-232
12. IR: One IrDA TX/RX header
13. USB: Support Six USB ports
14. Keyboard: PS/2 6-pin Mini Din
15. Mouse: PS/2 6-pin Mini Din
16. Sound: AC97 2.1 Sound, full-duplex
17. BIOS: Award BIOS version 6.1
18. Form Factor: LIGHT Board, 200x150mm
19. Power: DC12V-IN power Adapter input
21. Power Voltage: +12V (11.4V to 12.6V)
22. Power Consumption: Please refer to page 57
3
1-3 Hardware Notice Guide
1. Before installing the power supply with this motherboard, please attach the 12V/DC
( 4 pin connector )of the adapter to motherboard first.
After that, plug the adapter power to AC outlet.
Always normally shut down the computer before you move the system unit or remove
the power supply from the motherboard.
Please unplug the 12V/DC ( 4 pin connector ) of the adapter from motherboard first.
Then unplug the adapter from the AC outlet.
Please refer to procedure from the photo 1
2. There will be high possibility to burn out the CPU if you change/ modify any parts of the
CPU cooler.
3. Please wear wrist strap and attach it to a metal part of the system unit before handling a
component.
You can also touch an object that is of ground connection or with metal surface if you don't
have wrist strap.
4. Please be careful when you handle this product. Pay attention to & don't touch the
sharp-pointed components at the bottom PCB .
5. Please pay attention to this: Remove or change any components form the motherboard
will VOID the warranty of the motherboard you purchased .
6. Before you install/remove any components or make any jumper setting on the motherboard,
please make sure to disconnect the power first.
( Please follow the instructions as of this guide )
7. Please only use single sided Mini PCI card, do not use the double sided Mini PCI card
which is not suitable.
8. This does not support 16 bit mini PCI card
9. Please follow this instruction carefully when using the "POWERON after PWR-Fair" function.
When the DC power adaptor runs out of power, unplug it from the DC current;
when power returns plug it back in only after 5 seconds. If there is a power outage,
unplug it from the AC current, when power returns plug it back in only after 30 seconds.
Otherwise it will cause system locking or serious damage.
Remark 1:
Always insert/unplug the 12V/DC ( 4 pin connector ) horizontally & directly from the
motherboard.
DO NOT twist the 12V/DC ( 4 pin connector ) gently, it is designed to fit snugly .
Moreover, erratic pull / push testing with the DC Jack might cause the unpredictable
damage to the component & system unit.
4
Photo 1
Insert
1
2
3
Unplug
1
2
3
5
1-3-1 Installing the Mini PCI card
1. Align the Mini PCI card with the connector at a 45 degree angle.
2. Press the Mini PCI into the connector until you hear a click.
6
Notices:
1.The connectors are designed to ensure the correct insertion. If you feel resistance, check the
connectors & golden finger direction, and realign the card.
2. Make sure the retaining clips (on two sides of the slot) lock onto the notches of
the card firmly.
7
1-3-1.1 Removing the Mini PCI card
1. Release the Mini PCI card by pulling outward the two retaining clips and the card
pops up slightly.
2. Lift the mini PCI card out of its connector carefully.
8
1-4 Packing List*
1 CV700A Board
6 Utility CD Disk
2 DC 12V Power Adapter
7 User's Manual
3 One ATA 100 Flat Cable (2.54mm)
8 SATA DATE Cable (optional)
4 One slim IDE port flat Cable (2.00mm)
9 SATA HDD Power Cable (optional)
5 Power Cable
2
1
3
7
6
5
4
8
9
5
*The packing list above is for the users who purchase single motherboard. The users
who purchase the board with chassis may refer to the packing list in the Assembly Guide.
Please contact with your dealer if any of these items is missing or damaged
on delivery. And please keep all parts of the delivery package with packing
materials in case if you need to deliver or store the product in the future.
9
Chapter-2
Hardware Installation
This chapter provides the information how to install the hardware of CV700A.
Please follow section 1-4, 2-1 and 2-2 to check the delivery package and unpack
carefully. Please follow the jumper setting procedure.
2-1 Unpacking Precaution
The CV700A board has been well packed with an anti-static bag to protect its sensitive
components and circuitry from damage due to static electric discharge.
NOTE!
1. Do not touch the board or any other sensitive components without all necessary
anti-static protection.
2. Please pay attention to the voltage limitation of DC-IN12 V +- 5 %.
Overuse of DC-IN voltage limitation or change to another power adapter
( not provided with this system ) will VOID warranty.
You should follow these
steps to protect the board from the static electric
discharge whenever you handle the board:
1. Ground yourself by a grounded wrist strap at all times when you handle the CV700A.
Well secure the ALLIGATOR clip of the strap to the end of the shielded wire lead from
a grounded object. Please put on and connect the strap before handling the CV700A
for harmlessly discharge any static electricity through the strap.
2. Please use anti-static pad to put any components, parts, or tools on the pad whenever
you work on them outside the computer. You may also use the anti-static bag instead of
the pad. Please ask your local supplier for necessary parts on anti-static requirement.
3. Do not plug any connector or set any jumper when the power is on.
10
2-2 Unpacking checkup
First of all, please follow all necessary steps of section 2.1 to protect CV700A
from electricity discharge. With reference to section 1.3, please check the delivery package
again with following steps:
1. Unpack the CV700A board and keep all packing material, manual
and driver disc etc, do not dispose !
2. Is there any components lose or drops from the board? DO NOT CONTINUE
TO INSTALL THIS BOARD!CONTACT THE DEALER YOU PURCHASED THIS
BOARD FROM, IMMEDIATELY.
3. Is there any visible damage on the board? DO NOT CONTINUE TO INSTALL
THIS BOARD!CONTACT THE DEALER YOU PURCHASED THIS
BOARD FROM, IMMEDIATELY.
4. Check your optional parts (i.e. DDR2, CF etc.), all necessary jumpers
setting to jumper pin-set, and CMOS setup correctly.
Please also refer to all information of jumper settings in this manual.
5. Check your external devices (i.e. Add-On-Card, Driver Type etc.)
for complete add-in or connection and CMOS setup correctly.
Please also refer to all information of connector connection in this manual.
6. Please keep all necessary manual and driver disc in a good condition for future
re-installation if you change your Operating System.
11
2-3 Dimension
200x150(mm)
12
2-4 Layout
CPU FAN JF2
CN45
JSW1
JR1
CN4
DC12V IN
CN5
JKM1
SW1
JP1
JSL1
PW-LED
JLED1
HDD-LED
LAN-LED
EBGA CPU
CN3
CN11
CN7 COM1
DIMM1
CN10
CN700
CN13
CN46
VT8237R-Plus
JB1
CN16
CN14
CN2 VGA
BATTERY
JF1
SYS FAN
JI1
CN20
CN6 COM2
CN29
CN26
CN9 LAN2
CN28
CN8 LAN3
LAN3
CN18 IDE2
JCF1
CN19 IDE1
13
CN47
JUSB1
JUSB2
CN21
JCF2
SATA1
CN27
2-5 Diagram
CPU FAN JF2
JSW1
JR1
CN1
DC12V IN
SW1
JP1
CN5
PW-LED
HDD-LED
LAN-LED
CN3
CN7 COM1
DIMM1
CN10
CN13
CN16
CN14
JB1
CN2 VGA
CN20
JI1
JF1
SYS FAN
CN6 COM2
CN29
CN9 LAN2
CN28
CN47
CN8 LAN3
CN27
CN18 IDE2
CN19 IDE1
CN21
JCF1
JCF2
14
SATA1
2-5-1 Bottom Side Diagram
MPCI: Mini PCI Socket
. Back Panel (CV700A)
PS/2 Mouse
Parallel
RJ45 LAN 1
RJ45 LAN 2
DC 12V IN
USB
PS/2 Keyboard
COM 1
VGA
COM 2
RJ45 LAN 3
. Back Panel (CV702A)
RJ45 LAN 2
RJ45 LAN 1
DC 12V IN
COM
RJ45 LAN 3
15
2-6 Install Memory
This motherboard provides one 240-pin DUAL INLINE MEMORY MODULES (DIMM)
socket for memory expansion available from minimum memory size of 256MB to
maximum memory size of 1GB DDR2 RAM.
DDR2 clock supports: DDRII200, DDRII266
Valid Memory Configurations
Total Memory
DIMM1
System Accept or Not
DS/SS
Accept
Min. ~ Max.
256MB~1GB
SS: Single Sided DIMM
DS: Double Sided DIMM
NOTE!
Make sure the total installed memory does not exceed 1GB;
otherwise, the system may hang during startup.
DIMM1 (BANK0+BANK1)
Install DDR RAM module oriented as Fig. 2.1.
Figure 2.1
16
NOTE!
When you install DIMM module fully into the DIMM socket, the eject tab should be
locked into the DIMM module very firmly and fit into its indention on both sides.
WARNING!
2. Once you hear " Beep Beep Beep" sounds after turning on the power ,
please check if the DRAM is installed properly or not.
2-7 List of Jumpers
JB1: CMOS DATA SET
JCF1: CF card mast and slave select
JCF2: CF card Voltage select
17
2-8 Jumper Setting Description
A jumper is ON as a closed circuit with a plastic cap covering two pins. A jumper is OFF as an
open circuit without the plastic cap. Some jumpers have three pins, labeled 1, 2, and 3.
You could connect either pin 1 and 2 or 2 and 3.
The below figure 2.2 shows the examples of different jumper settings in this manual.
Figure 2.2
All jumpers already have its default setting with the plastic cap inserted as ON,
or without the plastic cap as OFF. The default setting may be referred in this
manual with a " " symbol .
*
2-9 CMOS Data Set
A battery must be used to retain the motherboard configuration in CMOS RAM.
Close pin 1and pin 2 of JB1 to store the CMOS data.
To clear the CMOS, follow the procedures below:
1. Turn off the system and unplug the AC power
2. Remove DC 12V power cable from DC 12V power connector
3. Locate JB1 and close pin 2-3 for a few seconds
4. Return to its normal setting by shorting pin 1-2
5. Connect DC 12V power cable back to DC 12V power connector
18
Note: Do not clear CMOS unless
1. Troubleshooting
2. Forget password
3. You fail over-clocking system
JB1
*1-2
2-3
Description
*Normal Set
CMOS Data clear
JB1
3
2
1
3
2
1
*Normal
Clear Setting
2-10 JCF2 CF Card Power Voltage select
If you use CF card and HDD together, we suggest you
use the jumper setup for +5V.
JCF2
Description
*1-2
*For CF CARD power voltage select +5V
2-3
For CF CARD power voltage select +3.3V
JCF2
3
2
1
+5V*
* We use
to refer to as pin1
19
3
2
1
3.3V
2-11 JCF1 CF Card Master and Slave selection
If you use CF card and HDD together, please set CF as Master and HDD as Slave.
JCF1
Description
*1-2
*CF Card use Master type
2-3
CF Card use Slave type
JCF1
3
2
1
3
2
1
Master*
20
Slave
Chapter-3
Connection
This chapter provides all necessary information of the peripheral's connections,
switches and indicators. Always power off the board before you install the peripherals.
3-1 List of Connectors
CN1: DC 12V-IN DIN Connector
CN4: DC 12V-IN Connector (Share to CN1)
CN5: PS2 Keyboard /Mouse Connector
JKM1: PS2 Keyboard /Mouse Connector (Share to CN5)
CN3: USB port 0/1 and LAN1 RJ45 Connector(or CN11 single RJ45)
CN7: COM1 port Connector
CN2: VGA DB15 Connector
CN46: VGA Header
CN10: Printer (LPT)port
CN6: COM2 port Connector
CN9: LAN2 RJ45 Connector
CN29: Line out connector
CN8: LAN3 RJ45 Connector
CN28 : Mic-in connector
CN19: IDE1 40 pin (2.54mm)Connector
CN47: Line out /Line in/ Mic-in Header
CN18: IDE2 44 pin (2.0mm)Connector
JF2: CPU FAN connector
CN20:CF 50 pin socket
JF1: System FAN connector
SATA1: S-ATA IDE 7pin Wafer
JI1: IR connector
CN14: USB port 2 connector
CN21: DC +5/+12V output connector
CN16: USB port 3 connector
CN26: I2C Bus connector
CN27: USB port 4 connector
CN13: TV out connector
JUSB1/JUSB2:USB 4/5 port connector
MPCI1:Mini PCI socket
JR1: Reset pin
SW1 : System power switch
JSW1 : System power switch pin header
PW LED : System power LED or pin header
JP1: System power LED pin header
HD LED : Hard Disk LED or pin header
LAN LED: LAN active LED
21
3-2 FAN Connector
CV700A provides one CPU fan connector and one system fan connector.
CPU Fan Connector- JF2
PIN NO.
Description
System FAN Connector-JF1
1
FAN Control ON/OFF
JF2
pin1
2
+12V
3
FAN speed Sensor
JF1
pin1
*Note : DC- in +12V by switch to DC-out voltage +12V
So DC -in need stable +12V input
3-3 IDE Connectors
PIN NO.
There are two kinds of IDE connectors on this
board, 40-pin and 44-pin. Each can support up
to two IDE-inferface devices. One standard
40-pin header daisy-chain driver connector
provides as IDE1 with following pin assignment.
40 pins (2.54mm)-CN19(IDE 1)
This connector supports the provided IDE hard
disk ribbon cable. After connecting the single
plug end to motherboard, connect the two
plugs at other end to your hard disk(s). If you
install two hard disks, you must configure the
second drive as Slave mode by setting its
jumpers accordingly. Please refer to the
documentation of your hard disk for the
jumper settings.
Note!
PIN 20 connector +5V of
IDE 1 could provide the
power of DOM
Description
PIN NO.
Description
1
RESET#
2
GROUND
3
DATA7
4
DATA8
5
DATA6
6
DATA9
7
DATA5
8
DATA10
9
DATA4
10
DATA11
11
DATA3
12
DATA12
13
DATA2
14
DATA13
15
DATA1
16
DATA14
17
DATA0
18
19
GROUND
20
21
DREQ
22
DATA15
+5V
GROUND
23
IOW#
24
GROUND
25
26
28
GROUND
27
IOR#
IORDY
29
DACK#
GROUND
31
IRQ14
30
32
33
SA 1
34
ATA 33/66/100
CABLE SELECT
PULL DOWN
NC
35
SA 0
36
37
HD CS0#
38
HD CS1#
39
HD LED
40
GROUND
Note: Pin20 is +5V power can use new type DOM module.
22
SA 2
44 pins(2.0mm)-CN18 (IDE2)
This connector supports slim type 2.5" HDD. Follow the same procedure described for the
primary IDE connector. You may also configure two hard disks as both Masters using one
ribbon cable on the primary IDE connector and another ribbon cable on the secondary
IDE connector. (See Appendix B)
PIN NO.
Description
PIN NO.
Description
1
RESET#
2
GROUND
3
DATA7
4
DATA8
5
DATA6
6
DATA9
7
DATA5
8
DATA10
9
DATA4
10
DATA11
11
DATA3
12
DATA12
13
DATA2
14
DATA13
15
DATA1
16
DATA14
17
DATA0
18
19
GROUND
20
21
DREQ
22
DATA15
KEY
GROUND
23
IOW#
24
GROUND
25
26
28
GROUND
27
IOR#
IORDY
29
DACK#
GROUND
31
IRQ15
30
32
33
35
37
SA 1
SA 0
39
HD CS0#
HD LED
41
43
34
36
38
PULL DOWN
NC
ATA 33/66/100 CABLE SELECT
SA 2
HD CS1#
40
GROUND
+5V
42
+5V
GROUND
44
NC
pin1
IDE2
pin1
IDE1
CN18 (IDE2)
CN19 (IDE1)
23
3-4 Compact - Flash Memory Socket
C700A configures CompactFlash Storage Card in IDE mode. It will use IDE channel when
CompactFlash card is plugged in. This socket supports CF Card Type I/II socket spec.
CF Socket 50pin----CN20
PIN NO.
Description
PIN NO.
Description
1
GND
26
GND/-CD1
2
DATA3
27
DATA11
3
DATA4
28
DATA12
4
DATA5
29
DATA13
5
DATA6
30
DATA14
6
DATA7
31
DATA15
7
-CS0
32
-CS1
8
NC(A10)
33
GND/-VS1
-IOR
-IOW
VCC/-WE(PH)
9
-ATA_ SEL
34
10
NC(A9)
35
11
NC(A8)
36
12
NC(A7)
37
INTR
13
38
39
VCC*
14
VCC*
NC(A6)
15
NC(A5)
NC(-VS2)
16
NC(A4)
40
41
17
NC(A3)
42
IORDY
18
SDA2
43
DREQ
19
20
SDA1
SDA0
44
-DACK
-DASP
21
-CSEL
RESET
DATA0
45
46
-PDIAG
22
DATA1
47
DATA8
23
24
25
DATA2
NC/-IOCS16
48
49
50
DATA9
DATA10
GND
GND/-CD2
CN20
Note: Refer JCF1 /JCF2 Jumper set (CF socket share to IDE2)
24
3-5 Parallel Port Connector
Parallel Port connector is a D-type 25-pin female connector. The On-board Parallel Port can
be disabled through the BIOS SETUP (see Chapter 4)
.
CN10: Printer (LPT)Port ---CN10 D-SUB 25 PIN
PIN NO.
Description
PIN NO.
1
STROBE#
14
AUTO FROM FEED#
2
DATA0
15
ERROR#
3
DATA1
16
4
DATA2
17
5
DATA3
18
GROUND
6
DATA4
19
GROUND
7
DATA5
20
GROUND
8
DATA6
21
GROUND
9
DATA7
22
24
GROUND
GROUND
GROUND
25
GROUND
10
11
12
13
ACKNOWLEDGE
BUSY
PARER EMPTY
PRINTER SELECT
23
Description
INITIALIZE
PRINTER SELECT LN#
CN10
25
3-6 Serial Port Connector
The CV700A board offers two high speed NSI6C550 compatible UARTS with Read/ Receive
16 byte FIFO serial ports. The serial ports are two DB-9 external connectors. The On-board
serial port can be disabled through BIOS SETUP (see Chapter 4).
. CN7: COM1 Connector D-SUB 9-Pin
PIN NO.
Description
PIN NO.
Description
1
DCD
6
DSR
2
RXD
7
RTS
3
TXD
8
CTS
4
DTR
9
RI
5
GND
. CN6: COM2 Connector D-SUB 9-pin
PIN NO.
Description
PIN NO.
Description
1
DCD
6
DSR
2
RXD
7
RTS
3
TXD
8
CTS
4
DTR
9
RI
5
GND
CN7: COM1
CN6: COM2
26
3-7 Keyboard and Mouse Connector
CN5: PS2 Keyboard down side (Din 6 pin jack)
PIN NO.
Description
1
KB DATA
2
MS DATA
3
GND
4
+5V
5
KB CLOCK
6
MS CLOCK
CN5: PS2 Mouse up side (Din 6 pin jack)
PIN NO.
Description
1
MS DATA
2
NC
3
GND
4
+5V
5
MS CLOCK
6
NC
CN5
PS/2 Mouse
CN5
PS/2 Keyboard
JKM1: 6 PIN (1.25mm Wafer connector) Internal Keyboard / Mouse Connector
(Share to CN5)
PIN NO.
Description
1
+5
2
KB DATA
3
KB CLOCK
4
GND
5
MS DATA
6
MS CLOCK
27
3-8 USB Port/ Header
CN3 (Down side) : USB 0/1port Type A Jack
CN27: USB port 4 Type A jack
PIN NO.
Description
PIN NO.
Description
1
+5V
1
+5V
2
USB DATA 0/1-
2
USB DATA 6-
3
USB DATA 0/1+
3
USB DATA 6+
4
GND
4
GND
CN14 / CN16 : USB port 2/3 pin
(1.25mm Wafer connector)
JUSB1/JUSB2 USB 4/5 port
5pin header (2.54mm)
PIN NO.
Description
PIN NO.
Description
1
+5V
1
+5V
2
USB DATA - 4/5
2
USB DATA 6/7-
3
USB DATA + 4/5
3
USB DATA 6/7+
4
GND
4
KEY
5
GND
CN3
CN14 CN16
pin1
CN27
pin1
JUSB2
28
3-9 IR Connector
This built-in IR connector supports the optional wireless transmitting and receiving infrared
module. It supports Infra-red Data Association (IrDA) and Amplitude Shift Keyed IR (ASKIR).
You can configure the setting through the BIOS setup to use the IR function. (see Chapter 4)
.
JI1: IR connector ---5pin (1.25mm Wafer connector)
IR : ASKIR / IRDA
PIN NO.
Description
1
+5VSB
2
FIR
3
IRRX
4
GND
5
IRTX
pin1
JI1 IR
3-10 VGA Connector
. CN2: VGA DB15 Connector Up side (D SUB 15PIN)
PIN NO.
Description
PIN NO.
Description
PIN NO.
Description
1
RED
6
GND
11
NC
2
GREEN
7
GND
12
DDC DATA
3
BULE
8
GND
13
H-SYNC
4
NC
9
NC
14
V-SYNC
5
GND
10
GND
15
DDC CLOCK
CN2 VGA
3-10.1 VGA Header
. CN46 : VGA Header (2x5pin 2.0mm)
PIN NO.
Description
PIN NO.
Description
1
BULE
2
RED
3
GREEN
4
GND
5
H-SYNC
6
V-SYNC
7
DDC DATA
8
DDC CLOCL
9
GND
10
KEY
29
3-11 LAN Port
The Fast Ethernet controller provides 32-bit performance, PCI bus master capability, and full
compliance with IEEE 802.3 10/100Based-T specification.
For 10/100Base-T operation, please connect the network connection by plugging one end of
the cable into the RJ-45 jack of the CN9,CN8 Connector.
Besides 10/100 Base-T, CV700A can provide Giga LAN solution through CN9,CN8
once equipped with Intel 82541GI/PI/ER chipset.
.
CN3 (Up side) (or CN11 single RJ45-CV702A) :LAN1 Giga/100Mb Jack
CN9: LAN2 RJ45 Connector
CV700A
CN8: LAN3 RJ45 Connector
RJ45 CN8
PIN NO.
Description
PIN NO.
Description
1
TD0-/TX+
5
2
TD0+/TX-
6
TD2-/NC
TD2+/RX-
3
TD1-/RX+
7
TD3-/NC
4
TD1+/NC
8
TD3+/NC
RJ45 CN3
CV702A
RJ45 CN11
LAN Led
RJ45 LAN1 Connector--- LED define Giga/100/10MB Conector
Back side connector
RED LED
GREEN LED
YELLOW LED
Indicate
GIGA LAN
Link(light)
100Mb LAN
Link(light)
10Mb LAN
Link(light)
Fron side
LAN LED Header
Indicate
LAN10/100/1000BT Actived (light)
RJ45 LAN1 Connector--- LED define 10/100MB Conector
Back side connector
Link
Indicate
GREEN LED
GREEN LED
ORANGE LED
ORANGE LED
100Mb LAN
Link(light)
10Mb LAN
Link(light)
Fron side
LAN LED Header
Indicate
LAN10/100BT Actived (light)
30
RJ45 CN9
3-12 Audio Port Connector
The CV700A has an on-board AC'97 3D sound interface. There are the connectors of
LINE OUT, MIC-IN and CD-IN connectors.
The MIC-IN Jack and CD-IN header are for audio sound input. The LINE-OUT
connector is a 4-pin Jack for audio sound output.
. CN29 (Phone Jack) -----Line-OUT
.
CN28 (Phone Jack) -----MIC-IN
(3.5mm Phone jack or 5pin 2.54mm header)
(3.5mm Phone jack or 5pin 2.54mm header)
PIN NO.
Description
PIN NO.
Description
1
GND
1
GND
2
FRONT OUT-L
2
MIC-PW
3
NC
3
GND
4
NC
4
NC
5
FRONT OUT-R
5
MIC-IN
Speak out CN29
MIC-IN CN28
.
CN47: Line-out / MIC-in Header (2x4pin 2.0mm Header)
Description
PIN NO.
Description
1
Line-out-R
2
Line-out-L
3
GND
4
GND
5
Line-in-R
6
Line-in-L
7
Mic-in
8
Mic-in
PIN NO.
CN47
pin1
Note: If phone jack plunge into CN29 of the signal will disabled CN24 pin 1/2
31
3-13 DC 12V IN and DC out
. CN1: DC 12V-IN External Connector (4pin mini den connector)
PIN NO.
Description
1,2
+12V DC-IN
GND
3,4
CN1
DC 12V IN
. CN4: DC 12V-IN Internal Connector (4pin connector)
( For option connector)
PIN NO.
Description
3,4
+12V DC-IN
GND
1,2
3-14 DC +5/+12V output connector
. CN21 : DC +5/+12V output connector(2.5mm Wafer)
PIN NO.
Description
1
+5V
2
GND
3
GND
4
+12V*
* Note: DC in +12V by switch to DC-out voltage +12V
So DC in need stable +12V input
CN21
32
3-15 Serial ATA
.
SATA1: S-ATA IDE 7pin Wafer
PIN NO.
Description
1
GND
2
DATA TX+
3
DATA TX-
4
GND
5
DATA RX-
6
DATA RX+
7
GND
SATA1
3-16 I 2 C Bus Connector
. CN26: I C Bus connector 4pin (1.25mm Wafer connector)
2
PIN NO.
Description
1
+3.3V
2
GND
3
I2C CLK
4
I2C DATA
pin1
CN26
33
3-17 TV-OUT Connector
CN13 : TV-OUT S-VIDEO
(4pin 1.25mm Wafer)
PIN NO.
Description
1
LUMA-out
2
CHROMA-out
3
CVBS
4
GND
CN13
pin1
3-18 Front-Panel
. JR1: System Reset key( 2.0mm pin header)
. Power switch: PW-ON--- SW1
JSW1: Power on switch
Based on case design , there may be a power switch or a 2-pin header connected to the
case-mounted power switch. It is used to power ON/OFF the system.
pin1
JSW1
. Power LED: PW-LED / JP1
The Power LED is lit while the system power is on.
pin1
JR1
pin1
JP1
. IDE Activity LED: HDD-LED
HDD-LED shows the activity of the hard disk.
. LAN LED Activity LED
LAN1/ LAN2 LED shows the activity of network
HDD LED
SW1
LAN LED
34
Power LED
Chapter 4
Introduction of BIOS
The BIOS is a program located in the Flash Memory on the motherboard.
This program is a bridge between motherboard and operating system.
When you start the computer, the BIOS program gains control. The BIOS first
operates an auto-diagnostic test called POST (Power on Self Test) for all the
necessary hardware, it detects the entire hardware devices and configures the
parameters of the hardware synchronization. After these tasks are completed,
BIOS will give control of the computer back to operating system (OS). Since the BIOS
is the only channel for hardware and software to communicate with, it is the key factor
of system stability and of ensuring your system performance at best.
In the BIOS Setup main menu of Figure 4-1, you can see several options. We will
explain these options in the following pages. First, let us see the function keys
you may use here:
..
.
.
Press <Esc> to quit the BIOS Setup.
Press (up, down, left, right) to choose the option you
want to confirm or modify.
Press <F10> to save these parameters and to exit the BIOS Setup menu after
you complet the setup of BIOS parameters.
Press Page Up/Page Down or +/- keys to modify the BIOS
parameters for the active option.
4-1 Enter Setup
Power on the computer and press <Del> immediately to enter Setup.
If the message disappears before your respond but you still wish to enter Setup,
restart the system by turning it OFF then ON button on the system case. You may
also restart the system by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys.
If you do not press the keys at the proper time and the system does not boot, an
error message will display and you will be asked to
Press <F1> to continue, <Ctrl-Alt-Esc> or <Del> to enter Setup
35
4-2 Getting Help
Main Menu
The on-line description of the highlighted setup function is displayed at the
bottom of the screen.
Status Page Setup Menu/ Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use
and the possible selections for the highlighted item.
To exit the Help Window, press <Esc>.
4-3 The Main Menu
Once you enter Award BIOS CMOS Setup Utility, the Main Menu will appear on the
screen. The Main Menu has fourteen setup functions and two exit choices.
Use arrow keys to select among these items. Press <Enter> to accept or enter
the sub-menu.
Phoenix-AwardBIOS CMOS Setup Utility
Standard CMOS Features
Frequency/Voltage Control
Advanced BIOS Features
Load Fail-Safe Defaults
Advanced Chipset Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configurations
Save & Exit Setup
PC Health Status
Exit Without Saving
Esc : Quit
F9 : Menu in BIOS
F10 : Save & Exit Setup
↑↓→ ←
: Select Item
Time, Date, Hard Disk Type…
36
Standard CMOS Features
This Menu is for basic system configurations.
Advanced BIOS Features
This menu is to set the Advanced Features available in your system.
Advanced Chipset Features
This menu is to change the values in the chipset registers and optimize your
system performance.
Integrated Peripherals
This menu is to specify your settings for integrated peripherals.
Power Management Setup
This menu is to specify your settings for power management.
PnP/PCI configurations
This entry appears if your system supports PnP/PCI.
PC Health Status
This entry shows your PC health status.
Frequency/Voltage Control
This menu is to specify your settings for Miscellaneous Control.
Load Optimized Defaults
Use this menu to load the BIOS default values that are factory settings for optimal
system operation performance. It is provided for the skillful users who want to
push the motherboard to get better performance. The Optimized setting does not go
through all the reliability and compatibility tests, it is verified only with limited
configurations and loading (for example, a system that is equipped with only one VGA
card and one DIMM. Do not use Optimized setting unless you fully understand the
items in chipset setup menu.
37
Load Standard Defaults
Use this menu to load the BIOS default values for the optimum system performance.
Standard Defaults settings are relatively more reliable than Optimized Defaults.
All the product verifications, compatibility test reports and manufacture quality
controls are based on "Standard Defaults". We suggest you to use this setting
for normal operation. "Standard Defaults" is not the slowest setting for this
motherboard. If you need to verify an unstable problem, you may manually set the
parameter in "Advanced Chipset Features" to get slower and safer setting.
Set Supervisor/User Password
This menu is to set User and Supervisor Passwords.
Save & Exit Setup
Save CMOS values modified to CMOS and exit setup.
Exit Without Saving
Abandon all the CMOS values modified and exit setup.
4-4 Standard CMOS Features
The items in Standard CMOS Setup Menu are divided into several categories.
Each category includes no, one or more than one setup items. Use the arrow
keys to highlight the item and then use the <PgUp> or <PgDn> keys to select
the value you want to modify with this item.
Phoenix - AwardBIO S CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
May
Time (hh:mm:ss)
10 : 59 : 36
IDE
IDE
IDE
IDE
IDE
IDE
Channel
Channel
Channel
Channel
Channel
Channel
0
0
1
1
2
3
[
[
[
[
[
[
Master
Slave
Master
Slave
Master
Master
None
None
None
None
None
None
Item Help
]
]
]
]
]
]
Menu Level >
Change the day, moth,
year and century
[EGA/VGA]
Vid eo
Hal t On
[No
B ase Memor y
Enter:Select
F5:Previous Values
Errors]
640K
65472K
1024K
Extended Memory
Total Mem ory
↑↓→←:Move
5 2006
+/-/PU/PD:Value
F10:Save
F6:Fail-Safe Defaults
38
ESC:Exit
F1:General Help
F7:Optimized Defaults
4-5 Advanced BIOS Features
Phoenix-AwardBIOS CMOS Setup Utility
Advanced BIOS Features
Hard Disk Boot Priority
Virus Warning
CPU L1 & L2 Cache
CPU L2 Cache ECC Checking
[Press Enter]
[Disabled ]
[Enabled]
[Enabled]
Item Help
Quick Power On Self Test
[Enabled]
First Boot Device
[USB-FDD]
Second Boot Device
[HDD-0]
Third Boot Device
[CDROM]
Boot Other Device
[Enabled]
Boot Up NumLock Status
[On]
Typematic Rate Setting
[Disabled]
X Typematic Rate (Chars/Sec) [6]
[250]
X Typematic Delay (Msec)
Security Option
[Setup]
OS Select For DRAM > 64MB
[Non - OS2]
Video BIOS Shadow
[Enabled]
Full Screen LOGO Show
Small Logo (EPA) Show
↑↓→← :Move
Allows you to choose
the VIRUS warning
feature for IDE Hard
Disk boot sector
protection. If this
function is enabled
and someone attempt to
write data into this
area, BIOS will show a
warning message on
screen and alarm beep
[Enabled]
[Disabled ]
Enter:Select
F5:Previous Values
Menu Level >
+/ - /PU/PD:Value
F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
Virus Warning
The VIRUS Warning feature can help you protect IDE Hard Disk boot sector.
If this function is enabled, BIOS will show a warning message on screen and alarm
beep when somenoe attemps to write data into this area without permission.
Disabled (default) No warning message appears when anything attempts to
access the boot sector or hard disk partition table.
Enabled
Activate automatically when the system boots up. The system
will show the warning message if anything attempts to
access the boot sector of hard disk partition table.
39
4-6 Advanced Chipset Features
The Advanced Chipset Features Setup option is used to change the values of the
chipset registers. These registers control most of the system options in the computer.
Phoenix- AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Clock/Drive Control
AGP & P2P Bridge Control
Memory Hole
[Press Enter]
[Press Enter]
[Disabled]
System BIOS Cacheable
Video RAM Cacheable
[Enabled]
[Disabled]
↑↓→←:Move Enter:Select
F5:Previous Values
Item Help
Menu Level >>
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit F1:General Help
F7:Optimized Defaults
4-6-1 DRAM Clock/Drive Control
Phoenix- AwardBIOS CMOS Setup Utility
DRAM Clock/Drive Control
X
X
x
x
x
x
X
x
100 MHz
Current FSB Frequency
Current DRAM Frequency
266 MHz
DRAM Clock
[By SPD]
DRAM Timing
[Auto By SPD]
SDRAM CAS Latency [DDR / DDR 2.5 / 4
Bank Interleave
Disabled
Precharge to Active <Trp>
4T
Active to Precharge <Tras>
07T
Active to CMD <Trcd>
4T
REF toACT / REF (Trfc)
21T
ACT(0) to ACT(1) (TRRD)
3T
Read to Precharge (Trtp)
[2T]
Write to Read CMD (Twtr)
[1T/2T]
Write Recovery Time (Twr)
[4T]
DRAM Command Rate
[2T Command]
RDSAIT mode
[Auto]
RDSAIT selection
03
Item Help
Menu Level >>
↑↓→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
The menu is to include settings for the chipset dependents features.These features are
related to system performance. Make sure you fully understand the items contained in this
menu before you change anything. You may change the parameter settings to improve
system performance. However, it may make your system unstable if the setting is not
correct for your system configuration.
40
4-6-2 AGP & P2P Bridge Control
Phoenix- AwardBIOS CMOS Setup Utility
AGP & P2P Bridge Control
DRAM Clock/Drive Control
AGP & P2P Bridge Control
[64M]
[Enabled]
Item Help
Menu Level >>
↑↓→←:Move Enter:Select
F5:Previous Values
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit F1:General Help
F7:Optimized Defaults
4-7 Integrated Peripherals
Phoenix- AwardBIOS CMOS Setup Utility
Integrated Peripherals
VIA OnChip IDE Device
VIA OnChip PCI Device
SuperIO Device
[Press Enter]
[Press Enter]
[Press Enter]
Item Help
Menu Level >>
↑↓→←:Move Enter:Select
F5:Previous Values
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
41
ESC:Exit F1:General Help
F7:Optimized Defaults
4-7-1 VIA OnChip IDE Device
Phoenix-AwardBIOS CMOS Setup Utility
VIA OnChip IDE Device
OnChip SATA
SATA Mode
IDE DMA transfer
OnChip IDE Channe10
OnChip IDE Channe11
IDE Prefetch Mode
Primary Master
PIO
Primary Slave
PIO
Secondary Master PIO
Secondary Slave PIO
Primary Master
UDMA
Primary Slave
UDMA
Secondary Master UDMA
Secondary Slave UDMA
IDE HDD Block Mode
↑↓→←:Move
Enter:Select
F5:Previous Values
[Enabled]
[IDE]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
+/- /PU/PD:Value
Item Help
Menu Level >>
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
4-7-2 VIA OnChip PCI -Device
Phoenix - AwardBIOS CMOS Setup Utility
VIA-3058 AC97 Audio
OnChip USB Controller
OnChip EHCI Controller
USB Emulation
x USB Keyboard Support
x USB Mouse Support
↑↓→←:Move
Enter:Select
F5:Previous Values
[Auto]
[All Enabled]
[Enabled]
[ON]
Enabled
Enabled
+/- /PU/PD:Value
F10:Save
F6: Fail-Safe Defaults
Item Help
Menu Level >>
ESC:Exit
F1:General Help
F7:Optimized Defaults
VIA-3058 AC97 AUDIO
This item allows you to decide to enable/disable to support AC97 Audio.
42
4-7-3 Super IO Device
Phoenix-AwardBIOS CMOS Setup Utility
Super IO Device
Onboard Serial Port 1
Onboard Serial Port 2
Onboard Parallel Port
X EPP Mode Select
X ECP Mode Use DMA
↑↓→←:Move
Enter:Select
F5:Previous Values
[3F8/IRQ4]
[2F8/IRQ3]
[378/IRQ7]
EPP1.7
3
+/- /PU/PD:Value
Item Help
Menu Level >>
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
4-8 Power Management Setup
The Power Management Setup allows you to configure your system to most
effectively energy saving while operating in a manner consistent with your
own style of computer use.
IRQ / Event Activity Detect
Please refer to section4-8-1
43
4-8-1 IRQ / Event Activity Detect
IRQs Activity Monitoring
Please refer to section4-8-1.1
4-8-1.1 IRQs Activity Monitoring
44
4-9 PnP / PCI Configuration Setup
This section describes how to configure the PCI bus system. PCI, or Personal Computer
Interconnect, is a system which allows I/O devices to operate at the speed the CPU itself
keeps when CPU communicates with its own special components. This section covers
some very technical items and we strongly recommended that only experienced users
should make any change to the default settings.
Resource Controlled By
The Award Plug and Play BIOS can automatically configure all of the boot and Plug
and Play compatible devices. However, this capability means absolutely nothing unless
you are using a Plug and Play operating system such as Windows 95/98. If you set
this field to "manual", choose a specific resource by going into each sub menu that
follows this field (a sub menu is preceded by a ">").
The settings are Auto (ESCD) or Manual.
IRQ Resources
When resources are controlled manually, each system interrupt is assigned a type,
depending on the type of device using the interrupt.
PCI/VGA Palette Snoop
Leave this field at Disabled. The settings are Enabled or Disabled.
45
4-10 PC Health Status
This section shows the status of your CPU, Fan, and overall system.
This is only available when there is Hardware Monitor function onboard.
Show PC Health in Post
During Enabled, it displays information list below. The choice is either
Enabled or Disabled
Current CPU Temperature/Current System Temp/Current FAN1,FAN2 Speed/
Vcore/3.3V/+5V/+12V
This will show the CPU/FAN/System voltage chart and FAN Speed
46
4-11 Frequency/Voltage Control
This section is to set CPU Frequency Control.
Phoenix-AwardBIOS CMOS Setup Utility
Frequency/Voltage Control
Auto Detect PCI Clk
Spread Spectrum
Item Help
[Disabled]
[Disabled]
Menu Level >
↑↓→←:Move
Enter:Select
F5:Previous Values
+/-/PU/PD:Value
F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
Auto Detect DIMM/PCI Clock
This item allows you to enable or disable Auto Detect DIMM/PCI Clock.
The settings are Enabled or Disabled.
Spread Spectrum
This item allows you to set the CPU Host/PCI clock Spread Spectrum.
The choice are Disabled or Enabled.
4-12 Load Fail-Safe/Optimized Defaults
Load Standard Defaults
When you press <Enter> on this item, you get a confirmation dialog box with a message
similar to:
Load Standard Defaults (Y/N)? N
Press <Y> to load the BIOS default values for the most stable system operation and
minimal performance.
Load Optimized Defaults
When you press <Enter> on this item, you get a confirmation dialog box with a message
similar to:
Load Optimized Defaults (Y/N)? N
Press <Y> to load the default values that are factory settings for optimal
system operation performance.
47
4-13 Set Supervisor/ User Password
You can set supervisor password, user password, or both. The differences are:
Supervisor password: You can enter the setup menus and change the options.
User password:
You can enter the setup menus but do not have the right to
change the options. When you select this function, the
following message will appear at the center of the screen to
assist you in creating a password.
ENTER PASSWORD:
Type the password, up to eight characters in length, and press <Enter>. The password
typed will clear any previous password from CMOS memory. You will be
asked to confirm the password. Type the password again and press <Enter>. You may
also press <Esc> to abort the selection without entering password.
To disable a password, just press <Enter> when you are prompted to enter the
password. A message will confirm if you want to disable the password. Once the
password is disabled, the system will boot and you can enter Setup menus freely.
PASSWORD DISABLED.
When a password has been enabled, you have to enter it every time before you
enter the Setup. This prevents an unauthorized person from changing any part of
your system configuration.
Additionally, when a password is enabled, you can also have the BIOS to request a
password at every time when your system is rebooted. This would prevent the
unauthorized user.
You can determine if the password is required within the BIOS Features Setup Menu
and its Security option. If the Security option is set to "System", the password will
be required both at boot and at entry to Setup. If set to "Setup",
the password is required only at the entry to Setup.
48
Chapter 5
DRIVER INSTALLATION
There is a SYSTEM INSTALL CD disk in the package. This CD has all the drivers you need
and some free application programs and utility programs. In addition, this CD also includes
an auto-detect software which can tell you which hardware is installed and which driver is
needed so that your system can function properly.
We call this auto detect software SYSTEM INSTALL.
SYSTEM INSTALL Supports WINDOWS
98/98SE/ME/2000/XP
Insert the CD into your CD-ROM drive and the SYSTEM INSTALL Menu should appear
as below. If the menu does not appear, double-click MY COMPUTER and double-click
CD-ROM drive or click START, click RUN, and type X:\AUTORUN.EXE (assuming X is your
CD-ROM drive).
From MAGIC INSTALL MENU you may make 3 selections:
1 . Auto detect main board and OS Into auto install driver Menu
2 . Explore CD to explore the contents of the CD
3 . EXIT to exit from SYSTEM INSTALL menu
49
Auto install driver Menu
1. VIA 4 IN 1
2. VGA
3. SOUND
4. USB2.0
5. LAN
6. DIRECTX9
7.OTHERS
install VIA IDE/AGP/IRQ ROUTING/INF driver
install on-board VGA driver
install AC97 Audio Codec Installing driver
install VIA USB2.0 hardware Installing driver
to LAN install driver readme file
To install DirectX9 driver readme file
To PenMount 6000 install driver readme file
Note: PenMount 6000 DRIVER IS TO BE INSTALLED UNDER WIN 2000/XP ONLY.
Each selection is illustrated as below:
50
5-1 VIA 4 IN 1
IDE :
AGP:
INF :
Install VIA IDE/AGP/ INF Driver
VIA ATAPI VENDOR SUPPORT DRIVER IS USED TO FIX
COMPATIBILITY ISSUE FOR IDE DEVICES.
VIA AGP DRIVER IS TO BE INSTALLED. IF YOU ARE USING AN AGP
VGA CARD, VIAGART.VXD WILL PROVIDE SERVICE ROUTINES TO YOUR
VGA DRIVER AND INTERFACE DIRECTLY TO HARDWARE, PROVIDING
FAST GRAPHIC ACCESS.
VIA REGISTRY DRIVER IS TO BE INSTALLED UNDER WINDOWS.
THE DRIVER WILL ENABLE VIA POWER MANAGERMENT CONTROLLER.
1.Click VIA 4 IN 1 when System Install
MENU appears.
2.Click NEXT when VIA Service Pack
Wizard appears.
3.License Agreement. Click NEXT.
4. Choose all the drivers. Click NEXT.
Note: VIA AGP Driver IS TO BE
INSTALLED UNDER WIN98 ONLY.
51
5.Installing Components List. Click NEXT.
6. This is to announce the Copy Right.
Click NEXT.
7.Click Finish to restart computer.
NOTE: SYSTEM INSTALL will auto detect file path
X:\driver\VIA\CN700\4IN1\setup.exe
This driver supports WINDOWS 95\98\98SE\NT4.0\2000\XP
52
5-2 VGA INSTALL CN700 VGA Driver
1. Click VGA when System Install
MENU appears.
2. Click NEXT when VIA/S3 CN700
Driver Setup appears.
3. This VIA/S3 CN700 Driver install will
begin copying the driver files.
Click NEXT.
4. Click FINISH to Restart Computer.
NOTE: The path of the file
For WINDOWS 98/98SE/ME
X:\driver\VIA\CN700\VGA\WIN98me\SETUP.EXE
For WINDOWS 2000/XP
X:\driver\VIA\CN700\VGA\WIN2KXP\SETUP.EXE
Note: When you install driver ,
the “Hardware Installation”
dialog in Windows XP will appear ,
click “countine Auyway”.
53
5-3 SOUND Install VIA Audio Codec Driver for VIA
1.Click SOUND when System Install
MENU appears.
2. Click NEXT install VIA AC97 Audio Driver
3. Click NEXT install VIA AC97
Audio Driver
4. Click FINISH to Restart Computer.
NOTE: The path of the file
For WIN98/ME/2K\XP
X:\ driver\via\viaudio\setup.exe
54
5-4 USB2.0 install VIA USB2.0 Installing driver
1.Click USB2.0 when System
Install MENU appears.
2. Click NEXT install USB2.0 Driver
NOTE: When you install driver for USB2.0
under Windows 2000.Please install SP4 first.
When you install driver for USB2.0 under
Windows XP.Please install SP1 first.
4. Click FINISH to Restart Computer.
3. Click NEXT install VIA USB2.0 Driver
NOTE: The path of the file
For WIN98/ME/2K\XP
x:\ driver\via\CN700\USB20\setup.exe
55
5-5 HOW TO DISABLE ON-BOARD SOUND
Enter BIOS SETUP. Choose INTEGRATE PERIPHERALS. Choose On-Chip Device
FUNCTION. Choose " AC97 Audio Disable " on-board sound function by pressing
PAGE DOWN KEY to Disable.
5-6 HOW TO UPDATE BIOS
In DOS Mode
STEP 1. Prepare a boot disc. (you may make one by clicking START, clicking RUN,
typing SYS A: , and clicking OK)
STEP 2. Copy utility program to your boot disc. You may copy it from DRIVER CD
X:\Diver\bios\AWDFLASH.EXE or download it from our web site.
STEP 3. Copy the latest BIOS for CV700A from our web site to your boot disc.
STEP 4. Insert your boot disc into A:
Start the computer and type "Awdflash A:\CV700Axxx.BIN/SN/PY/CC/R"
CV700Axxx.BIN is the file name of the latest BIOS. It may be CV700AA1.
BIN or CV700AA2.BIN
SN means don't save the current BIOS data
PY means renew the current BIOS data
CC means clear the current CMOS data
R
means restart computer
STEP 5. Press ENTER and the BIOS will be updated,
computer will restart automatically.
56
Appendix A: Power Consumption Test
Condition
Item
Spec
CPU
V4 - C7 1GHz
DDR RAM
DDR2 533/1GB
Operating System
Windows XPP/SP2
Test Program
3D Mark 2001SE
HDD 3.5"
Standard HDD
HDD 2.5"
Slim Type HDD
Mini PCI Card
Wireless LAN IEEE802.11g
Test Result for reference !
Start up
Maximum Stable
Hard Disk
Stand by
Standard HDD
0.10A
2.53A
Slim Type HDD
0.10A
1.51A
Operation
Maximum
Shut down
Maximum
1.51A
2.12A
1.89A
1.04A
1.67A
1.43A
The power consumption depends on your device choice!
Appendix B: Resolution list
640 x 480 x ( 256 / 16bit / 32bit )
800 x 600 x ( 256 / 16bit / 32bit )
1024 x 768 x ( 256 / 16bit / 32bit )
1280 x 1024 x ( 256 / 16bit / 32bit )
1366 x 768 x ( 256 / 16bit / 32bit )
1600 x 1200 x ( 256 / 16bit / 32bit )
57
Warning !
1. CF card & 2.5” HDD first boot issue
Due to the frequent update and change of Compact Flash card, it can’t always
work with 2.5” HDD at the same time. Users may try and get the test result.
2. Battery
Battery on board is consumables. Lex doesn’t guarantee the life time of it.
3. Fanless solution with HDD
Please be aware of specification & limitation for HDD when fanless solution
is implemented.
58
Warning !
1. CF card & 2.5” HDD first boot issue
Due to the frequent update and change of Compact Flash card, it can’t always
work with 2.5” HDD at the same time. Users may try and get the test result.
2. Battery
Battery on board is consumables. Lex doesn’t guarantee the life time of it.
3. Fanless solution with HDD
Please be aware of specification & limitation for HDD. when fanless solution
is implemented.
59

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement