- Computers & electronics
- Computer components
- System components
- Processors
- JVC
- JX-B555
- Instructions manual
advertisement
AV SELECTOR
SELECTEUR AV
SELECTOR AV
JX-S555
POWER
SOURCE SELECT
DUBBING
LOCK
LOOP
PROTECT
REMOTE CONTROL UNIT
FOR JX-S555
RM-AJ555
AV SELECTOR
POWER
JX-S555
AV SEL
ECTOR
STAND
BY
1
2
SOURC
E SELE
CT
3
4
5
G LOC
K
INPUT 3
• • •
S-VIDE
O
VIDEO
L
AUDIO
R
INSTRUCTIONS
MANUEL D'INSTRUCTIONS
MANUAL DE INSTRUCCIONES
For Customer Use:
Enter below the Serial No. which is located on the rear or bottom of cabinet. Retain this information for future reference.
Model No.
JX-S555
Serial No.
J5500-105A
Safety Information
FCC IMFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION —Changes or modifications not approved by JVC could void user’s authority to operate the equipment.
Contact
Address: JVC AMERICAS CORP.,
1700 VALLEY ROAD, WAYNE, N.J. 07470
Telephone: (973) 315-5000
WARNING: TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION (for CANADA)
This Class B digital apparatus meets all requirements of the Canadian Interference-causing Equipment Regulations.
RENSEIGNEMENT (Pour CANADA)
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matérier brouilleur du
Canada.
Thank you for purchasing this JVC product. Before you begin operating this unit, please read the instructions carefully to be sure you get the best possible performance. If you have any questions, consult your JVC dealer.
CAUTION
To reduce the risk of electrical shocks , fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
* It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.
IMPORTANT
1. Installation
●
Select a place which is level, dry and neither too hot nor too cold (between -5° C and 40° C/23° F and 104° F).
●
●
Keep away from direct sunlight.
Do not put it too close to a heater.
2. Power cord
●
●
●
Do not handle the power cord with wet hands!
Do not bend the power cord sharply.
When unplugging the power cord, do not pull on the cord,
Hold the plug itself and remove it from the AC outlet.
3. Malfunctions, etc.
●
There are no user serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer.
●
●
Do not insert any metallic object.
Do not allow water to get inside.
2
-EN
Contents
INTRODUCTION
BASIC OPERATION
ADVANCED OPERATION
OTHERS
Safety Information ............................................................................................ 2
Check the contents .......................................................................................... 3
Major Features ................................................................................................. 4
System Configuration Example ........................................................................ 5
Connectors, Controls and Indicators ............................................................... 6
Using the Remote Control Unit ........................................................................ 9
Watching Video .............................................................................................. 10
Dubbing (Multi-dubbing) ............................................................................... 12
Watching a Video Program While Recording Another one (Dubbing Lock) .. 14
Enjoy High-Quality Video and Audio from a DVD (Optical connection) ........ 16
Useful Tips ..................................................................................................... 18
S-VIDEO input/output connectors .............................................................. 18
Y/C separator .............................................................................................. 18
Y/C mixer .................................................................................................... 18
LOOP PROTECT function ........................................................................... 19
DUBBING LOCK button ............................................................................. 20
Component terminals ................................................................................. 21
OPTICAL connector .................................................................................... 21
Block Diagram ............................................................................................... 22
Troubleshooting .............................................................................................. 24
Specifications ................................................................................................. 26
Glossary ......................................................................................................... 27
Index .............................................................................................................. 28
Check the contents
Check the contents of the carton your JX-S555 came in. The following items should be found in the carton:
POWER
JX-S55
STAND
BY
R
This unit (JX-S555)
SOURC
E SELE
CT
Remote control unit (RM-AJ555)
POWER
SOURCE SELECT
RE
RM
FO
-A
CO
J55
NT
5
555 L U
NIT
( )
OR
DUBBING
LOCK
Battery (AA) x 2
(for operation testing)
(MONIT G LOC
OR SEL K
ECT) LOO
P PRO
TECT
INPUT 3
• • •
S-VIDE
O
VIDEO
AUDIO
R
Registration card and Safety guide Warranty card Instruction manual (this book)
EN-
3
Major Features
1 Component video terminals and Optical digital audio connectors provided.
2 Two component input, Y/C separation and mixing circuits are built in for the centralized management of the AV components.
3 5 inputs, 2 outputs, 2 monitor outputs and 1 audio-only monitor output, adequate for home theater systems.
4 A dubbing lock function permits the monitoring of a source during the dubbing of another source.
5 Signal transmission with little signal deterioration for high picture quality. (The component circuitry is compatible with 30 MHz.)
Projector
VCR
TV VCR
Camcorder
POWER
JX-S555
AV SEL
ECTOR
STAND
BY
1
2
SOURC
E SELE
CT
3
4
5
(MONIT
ECT) LOO
P PROT
ECT
INPUT 3
• • •
S-VIDE
O
VIDEO
L
AUDIO
R
DVD player
DBS
AV receiver
4
-EN
System Configuration Example
S-VHS VCR VHS VCR DVD player
DIGITAL CS TUNER TU-CSD2
DBS
S-VIDEO VIDEO L AUDIO R
(Analog output)
Camcorder
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
Cr/Pr
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
AV receiver
Projector
S-VHS VCR VHS VCR TV
EN-
5
Connectors, Controls and Indicators
Front Panel
1 2 3
POWER
JX-S555 AV SELECTOR
STANDBY
4 5 6 7
1 2
SOURCE SELECT
3 4 5
DUBBING LOCK
(MONITOR SELECT)
LOOP PROTECT
INPUT 3 • • •
S-VIDEO VIDEO L AUDIO R
9 8
1
POWER button
Press to turn the power ON or OFF.
2
POWER Indicator
The green LED lights when the POWER is set to ON.
3
STANDBY Indicator
The red LED is extinguished when the POWER is ON, but lights when it is OFF to indicate the Standby mode.
MEMO
If the unit power has been switched OFF to the
Standby mode and then ON again, it can be operated using the same settings as when the power was switched OFF.
4 SOURCE SELECT buttons (
☞
p. 11, 13, 15, 17)
Press to select an input component.
5 SOURCE SELECT indicators
(
☞
p. 11, 13, 15, 17)
The indicator of the input component selected by the
SOURCE SELECT button lights in red.
6
DUBBING LOCK button (
☞
p. 14, 20)
(MONITOR SELECT)
Press to disable the POWER and LOOP PROTECT button and fix the circuit output to the output connectors. This button is useful for preventing accidental or erroneous operation during dubbing. It lights in green when it is “ON”.
• When one of the SOURCE SELECT buttons is pressed while DUBBING LOCK is activated, only the VIDEO output from the MONITOR output is switched without changing the video signal being dubbed through the VIDEO output.
7
LOOP PROTECT button (
☞
p. 13, 15, 19)
Press this button when you don’t want the signal selected by the SOURCE SELECT button to be sent to the corresponding output terminal.
• ON: The input (video/audio) signals are not output at the output terminal having the same number as the input terminal.
• OFF: The input (video/audio) signals are output at the output terminal having the same number as the input terminal.
8
Input terminals (INPUT 3)
INPUT 3 : This set of input terminals includes an S-VIDEO input terminal, VIDEO input terminals and AU-
DIO input terminals. It is used for dubbing from a camcorder, etc.
9
Remote sensor
The remote control signals enter the unit by this route.
6
-EN
Rear panel
1 2 3
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
Cr/Pr
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
1
Input terminals (INPUT
1
,
2
,
4
,
5
)
Up to five source components (including one connected to the front panel input terminals) can be connected to the five sets of inputs of the JX-S555.
INPUT 1 , 2 : Each of these includes an S-VIDEO input terminal, VIDEO input terminal and AUDIO input terminals.
Connect to the S-VIDEO or VIDEO output terminal and AUDIO outputs on an AV component such as a VCR.
INPUT 4 , 5 : Each of these includes an S-VIDEO input terminal, component video input terminal and AUDIO input terminals and an OPTI-
CAL (digital) audio input connectors.
The component output on a DVD player or
DSS and optical output can be connected.
MEMO
• Connect to a component having a 3-pin component video output terminals for the
Y/Cb/Cr or Y/Pb/Pr signals.
• The video signal input at the component video input terminal is output only at the component output terminal of the MONI-
TOR OUT 2 .
2
Output terminals (OUTPUT 1 , 2 )
Up to two components can be connected to the outputs of the JX-S555.
OUTPUT 1 , 2 : Each of these includes an S-VIDEO output terminal; VIDEO output terminals and
AUDIO output terminals.
3
MONITOR output terminals
(MONITOR OUT 1 , 2 , AUDIO, OPTICAL (digital))
Connect the monitor output components to these outputs.
• MONITOR 1 : This set of terminals includes an S-VIDEO output terminal, VIDEO output terminal and an AUDIO output terminal.
Connect to the S-VIDEO or VIDEO input terminal and AUDIO input connector on a
TV.
• MONITOR 2 : This set of terminals includes an S-VIDEO output terminal; component video output terminals and AUDIO output terminals.
Connect to a TV equipped with component input terminals.
MEMO
• Even when this output is connected to the component input terminals of a TV, connect the S-VIDEO terminal or VIDEO terminals and AUDIO terminals of the
MONITOR OUT 1 to another input circuit of the TV.
• The S-VIDEO terminals and AUDIO output terminals of the MONITOR OUT 1 and 2 outputs output the same signal.
• The S-VIDEO output of the MONITOR
OUT 2 is convenient for connecting a projector.
• OPTICAL AUDIO output connectors (
☞
p. 16, 21)
Connect to the optical digital audio input connector of an DVD/MD component or AV receiver, etc.
EN-
7
Connectors Controls, and Indicators (Remote Control Unit)
Remote Control Unit
1
POWER
SOURCE SELECT
4
DUBBING
LOCK
LOOP
PROTECT
2
3
REMOTE CONTROL UNIT
FOR JX-S555
RM-AJ555
AV SELECTOR
1
POWER button
Press to turn the power ON or OFF.
2
SOURCE SELECT buttons (
☞
p. 11, 13, 15, 17)
Press to select an input component.
3
LOOP PROTECT button (
☞
p. 13, 15, 19)
Press this button when you don’t want the signal selected by the SOURCE SELECT button to be sent to the corresponding output terminal.
ON: The input (video/audio) signals are not output at an output terminal having the same number as the input terminal.
OFF: The input (video/audio) signals are output at the output terminal having the same number as the input terminal.
4
DUBBING LOCK button (
☞
p. 14, 20)
(MONITOR SELECT)
Press to disable the POWER and LOOP PROTECT button and fix the circuit output to the output terminals. This button is useful for preventing accidental or erroneous operation during dubbing.
• When one of the SOURCE SELECT buttons is pressed while the DUBBING LOCK is activated, only the VIDEO output from the MONITOR output is switched without changing the video signal being dubbed through the
VIDEO output.
8
-EN
Using the Remote Control Unit
Battery Installation
Press the tab to remove the cover of the battery compartment.
Insert two “AA”(R6, UM-3) dry-cell batteries.
Replace the cover.
Notes:
Battery
Precautions
Misuse of batteries could result in leakage. This could cause a fire or explosion.
To prevent this, pay special attention to the following points:
1. Be sure to insert the batteries with correct positive “+” and negative “-” polarities.
2. Do not heat, disassemble or short-circuit batteries and never dispose of batteries by throwing them in a fire.
3. Do not use new and old batteries together.
• Also read the caution displayed on the battery when in use.
*The provided batteries are for checking operation only.
Transmitted beam effective area
Remote sensor
AV selector
JX-S555 AV SELECTOR
POWER
STANDBY
1 2
SOURCE SELECT
3 4 5
DUBBING LOCK
(MONITOR SELECT)
LOOP PROTECT
INPUT 3 • • •
S-VIDEO VIDEO L AUDIO R
Within 8 m
Approx. 60 °
POWER
SOURCE SELECT
DUBBING
LOCK
SELECT
LOOP
PROTECT
REMOTE CONTROL UNIT
FOR JX-S555
RM-AJ555
AV SELECTOR
Remote control unit
Note:
• If the remote controllable distance between the remote and main unit decreases, the batteries are depleted and should be replaced with new ones
("AA"-size (R6/UM-3) batteries.
EN-
9
Watching Video
Connect a VCR to INPUT 1 of the JX-S555 and watch the video played back on the VCR.
• This shows an example of one of several possible connections. Also refer to the instruction books of the other components you are using for operation and connection details.
VCR (Playback deck)
: Signals
To
S-VIDEO
Output
To VIDEO/
AUDIO
Output
To
S-VIDEO
Input
To VIDEO/
AUDIO
Input
1 1 1
(yellow)
(white)
(red)
JX-S555 Rear panel
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT Cr/Pr
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
The video/audio signals selected by the SOURCE
SELECT button can be simultaneously output to the MONITOR OUT 1 and 2 terminals.
To VIDEO/AUDIO Input
(yellow)
(white)
(red)
To S-VIDEO Input
TV
Connection precautions
• Before making any connections, turn off the power to all components.
• The S-VIDEO and VIDEO (yellow) terminals do not need to be connected simultaneously. If your connected VCR or
TV has S-VIDEO input/output terminals, a clearer video can be viewed by connecting it to the S-VIDEO terminal.
• If both the S-VIDEO input terminal and the VIDEO input terminal are connected between the VCR and the JX-S555, the signal from the S-VIDEO input terminal is given priority.
10
-EN
Connection tips
• Connect to the OUTPUT terminals on the JX-S555 so that the VCR can be used as a recording machine.
POWER
1
Turning the power on
SOURCE SELECT
DUBBING
LOCK
2
Selecting a VCR
LOOP
PROTECT
SELECT
1
.
Press POWER to turn on the JX-
S555.
• The POWER indicator lights in green.
POWER
2
.
Press SOURCE SELECT "1" to select VCR1.
• The indicator lights in red.
REMOTE CONTROL UNIT
FOR JX-S555
RM-AJ555
AV SELECTOR
1
POWER
JX-S555 AV SELECTOR
STANDBY
1 2
SOURCE SELECT
3 4 5
DUBBING LOCK
(MONITOR SELECT)
LOOP PROTECT
INPUT 3 • • •
S-VIDEO VIDEO L AUDIO R
2
MEMO
• If the SOURCE SELECT "1" indicator on the JX-S555 is already lit, it is not required to press the SOURCE SELECT "1" button.
3
.
Turn the TV on and select the input.
• Turn the TV on and select the input connected to the MONITOR OUT terminals on the JX-S555.
4
.
Turn on the VCR’s power and start playback.
VCR
PLAY
MEMO
• When you want to watch a video on another VCR, press the
SOURCE SELECT button to select the line number that the
VCR is connected to.
Notes:
• Set the LOOP PROTECT button to ON. (
☞
p. 19)
• You can not operate the POWER and LOOP PROTECT buttons when the DUBBING LOCK button is pressed. (
☞
p. 20)
EN-
11
Dubbing (Multi-dubbing)
You can dub a video program from VCR 1 (INPUT 1 ) to VCR 2 (OUTPUT 2 ) .
This shows an example of one of several possible connections. Also refer to the instruction books of the other components you are using for operation and connection details.
VCR 1 (Playback deck)
: Signals
To VIDEO/
AUDIO
Output
To
S-VIDEO
Output To VIDEO/
AUDIO
Input
To
S-VIDEO
Input
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
Cr/Pr
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
JX-S555 Rear panel
2 2
(yellow)
(white)
(red)
To VIDEO/AUDIO Input
(yellow)
(white)
(red)
To S-VIDEO Input TV
To
S-VIDEO
Output
To VIDEO/
AUDIO
Output To
S-VIDEO
Input
To VIDEO/
AUDIO
Input
VCR 2 (Recording deck)
Connection precautions
• Before making any connections, turn off the power to all components.
• The S-VIDEO and VIDEO (yellow) terminals do not need to be connected simultaneously. If your connected VCR or
TV has S-VIDEO input/output terminals, a clearer video can be viewed by connecting it to the S-VIDEO terminal.
• If both the S-VIDEO input terminal and the VIDEO input terminal are connected between the VCR and the JX-S555, the signal from the S-VIDEO input terminal is given priority.
12
-EN
Connection tips
• Connect to the OUTPUT 1 terminals on the JX-S555 so that VCR 1 can be used as a recording machine.
(Connect the output terminals on VCR 2 to the INPUT
2 terminals on the JX-S555.)
Preparation
• Turn on the power of the JX-S555.
• Turn on the TV and select the input connected to the MONITOR OUT terminals on the JX-S555.
• Turn on the power of VCR to prepare for dubbing.
POWER
SOURCE SELECT
DUBBING
LOCK
1
Selecting VCR 1
LOOP
PROTECT
SELECT
1
.
Press SOURCE SELECT "1" to select
VCR1 as the source component.
• The indicator lights in red.
REMOTE CONTROL UNIT
FOR JX-S555
RM-AJ555
AV SELECTOR
MEMO
• If the SOURCE SELECT "1" indicator on the JX-S555 is already lit, it is not required to press the SOURCE SELECT "1" button.)
2
.
Play back a tape on VCR 1.
VCR 1
PLAY
POWER
JX-S555 AV SELECTOR
STANDBY
1 2
SOURCE SELECT
3 4 5
DUBBING LOCK
(MONITOR SELECT)
LOOP PROTECT
INPUT 3 • • •
S-VIDEO VIDEO L AUDIO R
1
3
.
Start recording on VCR 2.
VCR 2
REC
• Set the input switch on the recording VCR to the external input mode (AUX) when dubbing.
• Set the recording VCR to S-VIDEO input when using an S-VIDEO input terminal for recording.
MEMO
• To watch a video obtained by dubbing, press the SOURCE
SELECT button of the input where the dubbing destination
VCR is connected.
Notes:
• Leave the LOOP PROTECT button ON (
☞
p. 19).
• Some video software may contain signals to prevent it from being copied. If you try to copy such a program, the results will not be viewable.
• Recording of copyrighted material for purposes other than personal use is illegal without permission of the copyright holder.
EN-
13
Watching a Video Program While Recording Another one
(Dubbing Lock)
Connect the VCR 1 for use in watching to INPUT 1, connect the VCR 2 for use in recording to INPUT
2, connect a DBS to the INPUT 5 and watch the DBS video while performing dubbing from the
VCR1 to the VCR 2:
This shows an example of one of several possible connections. Also refer to the instruction books of the other components you are using for operation and connection details.
VCR 1 (Playback deck)
Playback picture
DBS
Program picture
To VIDEO/
AUDIO
Output
To
S-VIDEO
Output
To VIDEO/
AUDIO
Input
To
S-VIDEO
Input
To
AUDIO
Output
To
S-VIDEO
Output
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
Cr/Pr
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
JX-S555
Rear panel
(yellow)
(white)
(red)
2 2
To VIDEO/AUDIO Input
(yellow)
(white)
(red)
To S-VIDEO Input TV
Program picture
To
S-VIDEO
Output
To VIDEO/
AUDIO
Output
To
S-VIDEO
Input
To VIDEO/
AUDIO
Input
: Flow of VCR1 signal
: Flow of DBS signal
Recorded picture
VCR 2 (Recording deck)
Connection precautions
• Before making any connections, turn off the power to all components.
• Although it is not required to connect both the S-VIDEO terminal and VIDEO terminals (yellow), it is recommended to connect the S-VIDEO terminals if your TV and/or VCR have the S-VIDEO inputs/outputs. This will allow you enjoy video with a higher picture quality.
• If both the S-VIDEO input terminal and the VIDEO input terminal are connected between the VCR and the JX-S555, the signal from the S-VIDEO input terminal is given priority.
14
-EN
Connection tips
• Connect to the OUTPUT 1 terminals on the JX-S555 so that VCR 1 can be used as a recording machine.
(Connect the output terminals on VCR 2 to the INPUT
2 terminals on the JX-S555.)
Preparation
• Turn on the power of the JX-S555.
• Turn on the TV and select the input connected to the MONITOR OUT terminals on the JX-S555.
• Turn on the power of the DBS to prepare for recording and playback.
POWER
SOURCE SELECT
1
Selecting VCR 1
DUBBING
LOCK
LOOP
PROTECT
5
Selecting DBS
SELECT 4
Set the dubbing lock mode
REMOTE CONTROL UNIT
FOR JX-S555
RM-AJ555
AV SELECTOR
1
.
Press SOURCE SELECT "1" to select
VCR1 as the source component.
• The indicator lights in red.
MEMO
• If the SOURCE SELECT "1" indicator on the JX-S555 is already lit, it is not required to press the SOURCE SELECT "1" button.
2
.
Start playback of VCR1.
• The VCR1 playback video is displayed on the TV screen.
PLAY
PLAYPlayback video
POWER
JX-S555 AV SELECTOR
STANDBY
1 2
SOURCE SELECT
3 4 5
DUBBING LOCK
(MONITOR SELECT)
LOOP PROTECT
INPUT 3 • • •
S-VIDEO VIDEO L AUDIO R
1 5 4
3
.
Start recording of VCR2.
REC
4
.
Press DUBBING LOCK to set the dubbing lock mode.
• The indicator lights in green.
DUBBING
LOCK
To exit from dubbing lock mode:
• Press DUBBING LOCK again.
MEMO
• When the input source is changed by pressing one of the
SOURCE SELECT buttons in the dubbing lock mode, the video displayed on the TV connected to the MONITOR OUT can be changed without affecting the video being dubbed.
SELECT
5
.
Press SOURCE SELECT "5" to watch the video of the DBS.
• The SOURCE SELECT "5" indicator lights in red.
• The DBS video is displayed on the TV screen.
DBS video
Notes:
• Set the LOOP PROTECT button to ON. (
☞
p. 19)
• You can not operate the POWER and LOOP PROTECT buttons when the DUBBING LOCK button is pressed. (
☞
p. 20)
EN-
15
Enjoy High-quality Video and Audio from a DVD
(Optical connection)
Connect a DVD player to INPUT terminal 4, then connect a TV equipped with a component terminal to the MONITOR OUT 2 and connect an AV receiver equipped with an OPTICAL connector to an
OPTICAL output connector.
This shows merely an example of connection. Also refer to the Instruction books of the other components you are using for their connection and operation procedures.
To Component Output
(green)
To Component Output
(green)
(blue)
DVD Player (Playback deck)
(blue)
: Signals
(red) (red)
To
S-VIDEO
Output
To
AUDIO
Output
To Digital AUDIO Output
(white)
(red)
OPTICAL
4
Cr/Pr
Y
Cb/Pb
JX-S555 Rear panel
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
Cr/Pr
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
To
AUDIO
Input
To
S-VIDEO
Input
To
AUDIO
Input
To
Component
Input
TV
Connection precautions
• Turn off the power to all components before making connections.
• Even when connection using a component video cord output is used, also connect the S-VIDEO and audio cords.
The audio cannot be output unless an audio cord is connected.
TV
(Equipped with component terminals)
AV receiver
• The video signals from the VIDEO component input at IN-
PUT 4 and 5 are output only at the component video output terminals of MONITOR OUT 2 . The video signals are not converted into composite video and S-VIDEO signals.
• The OPTICAL signal from INPUT 4 , 5 can only be output to the AUDIO MONITOR OUT OPTICAL connector. It is not converted to an analog AUDIO signal.
• To watch the video input to INPUT 1 - 3 , also connect a
TV to the MONITOR OUT 1 .
16
-EN
Preparation • Turn ON the JX-S555.
POWER
SOURCE SELECT
DUBBING
LOCK
1
LOOP
Selecting the DVD player
REMOTE CONTROL UNIT
FOR JX-S555
RM-AJ555
AV SELECTOR
POWER
JX-S555 AV SELECTOR
STANDBY
1 2
SOURCE SELECT
3 4 5
DUBBING LOCK
(MONITOR SELECT)
LOOP PROTECT
INPUT 3 • • •
S-VIDEO VIDEO L AUDIO R
1
1
.
Press SOURCE SELECT "4" to select
DVD player as the source component.
• The indicator lights in red.
MEMO
• If the SOURCE SELECT "4" indicator on the JX-S555 is already lit, it is not required to press the SOURCE SELECT "4" button.
2
.
Turn ON the TV and select the component video input.
TV
POWER
TV
INPUT SELECT
3
.
Turn ON the AV receiver and select the OPTICAL input, then set the Digital Surround mode to ON.
DIGITAL
SURROUND POWER SOURCE SELECT
4
.
Play the DVD.
• The DVD player video is displayed on the TV screen.
DVD
PLAY
Notes:
• Some DVD software contains recording of copy inhibit signals. When such software is dubbed between VCRs, the copy guard system functions to make the dubbed results abnormal.
• The copyright laws prohibit the use of materials recorded on videotapes by the user without the permission of the copyright owners unless the user use the tapes for personal use.
EN-
17
Useful Tips
S-VIDEO input/output connectors
• The S-VIDEO input/output connectors are terminals for the
Y/C (luminance/chrominance) separate video signals.
• If these connectors are connected to a VCR equipped with
S-VIDEO connectors, recording and playback of clearer video becomes possible by reducing loss in the video signal.
• A VCR not equipped with S-VIDEO connectors should be connected to the VIDEO terminals, which transmit the signal obtained by synthesizing the Y/C signals (composite signal).
Y/C separator
• The output circuits of the JX-S555 incorporate circuitry for separating the video signals input through the VIDEO terminals (composite signal) into Y/C (luminance/chrominance) signals.
This feature is convenient in dubbing from a VCR without S-
VIDEO connectors to a VCR equipped with them or watching the video from a VCR without S-VIDEO connectors on a
TV equipped with them.
: Signals
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
Cr/Pr
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
The Y/C separator works with composite signal.
Video/Audio cable
S-VIDEO cable
Audio cable
(VCR without an S-VIDEO output) (VCR with an S-VIDEO input)
Example of Y/C Separator
Y/C mixer
• The output circuits of the JX-S555 incorporate circuitry for mixing the video signals input through the S-VIDEO terminals (separate signals) into a composite video signal.
This feature is convenient in dubbing from a VCR equipped with S-VIDEO terminals to a VCR without them.
: Signals
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT Cr/Pr
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
The Y/C mixer works with the S-VIDEO signal.
S-VIDEO cable
Audio cable
Video/Audio cable
(VCR with an S-VIDEO output) (VCR without an S-VIDEO input)
Example of Y/C Mixer
18
-EN
LOOP PROTECT function
The LOOP PROTECT ON/OFF function determines whether the input (video/audio) signal is output to the corresponding output terminal. Normally leave this button ON.
䡵 LOOP PROTECT ON
(Signal cannot be output to itself)
(The LOOP PROTECT indicator is lit)
䡵 LOOP PROTECT OFF
(Signal can be output to itself)
(The LOOP PROTECT indicator is off)
VCR 1
Set the LOOP PROTECT function to ON to prevent output back to VCR 1 and to avoid video deterioration.
(Recording)
(Playback)
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
Cr/Pr
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
VCR 1
(Playback)
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
Cr/Pr
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
(Playback) (Recording)
VCR 2
: Signal flow when
VCR 1 is played
back
VCR 2 (Recording) VCR 3 (Recording)
Connect INPUT/OUTPUT 1 on the JX-S555 to VCR 1 and
INPUT/OUTPUT 2 to VCR 2 to enable both to be used as recording or playback decks in multi-dubbing.
The video/audio signals from VCR1 are output to VCR2 but they are also output to VCR1 (because the OUTPUT 1 of the JX-S555 is connected to the input of VCR1).
In this case, the image from VCR 1 will be degraded, preventing high-quality dubbing. Set the LOOP PROTECT function to ON to prevent signal deterioration and stop output to
OUTPUT 1 .
When dubbing from VCR 1 to 2 different VCRs, one more set of OUTPUT terminals is required when connecting IN-
PUT/OUTPUT 1 on the JX-S555 to the INPUT/OUTPUT on
VCR 1.
When you want to extend a set of the OUTPUT terminals, set the LOOP PROTECT function to OFF, and connect the
OUTPUT 1 terminals on the JX-S555 to the recording VCR.
When the LOOP PROTECT function is set to OFF, the same signal can be output to all the OUTPUT terminals.
EN-
19
Useful Tips (continued)
DUBBING LOCK button
• DUBBING LOCK button
Provides the dubbing lock function for prevention of accidental operational mistakes as well as a monitor select function for watching a video program while recording another.
Dubbing lock function
When the DUBBING LOCK button is pressed while the VCR for recording is in use, the POWER and LOOP PROTECT buttons are disabled.
Also, even when the SOURCE SELECT button is pressed by mistake, the dubbing lock function keeps the signal output from the output terminals so that the recording of the VCR can be continued.
Operation disabled
POWER
JX-S555 AV SELECTOR
STANDBY
Operation available by monitor select function
DUBBING
LOCK ON
Operation disabled
1 2
SOURCE SELECT
3 4 5
DUBBING LOCK
(MONITOR SELECT)
LOOP PROTECT
INPUT 3 • • •
S-VIDEO VIDEO L AUDIO R
Monitor select function
This function is most often used in “watching a video program while recording another one”. Pressing the DUBBING
LOCK button during recording sets the dubbing lock mode, the user can change the video displayed on the TV screen by pressing one of the SOURCE SELECT buttons.
(The SOURCE SELECT “1” and “4” indicators light in red.)
• Flow of monitor select function depending on the DUBBING LOCK button
SOURCE SELECT 1
ON
OUTPUT 1, 2 : VCR1 output
(Source 1)
MONITOR output : VCR1 output
(Source 1)
Player VCR1 Player
Video switched by monitorselect function
VCR2
: Flow of VCR1 signal
: Flow of VCR2 signal
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT Cr/Pr
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
DUBBING LOCK
ON
OUTPUT 1, 2 : VCR1 output
(Source 1)
MONITOR output : VCR1 output
(Source 1)
Recorder VCR3
SOURCE SELECT 4
ON
OUTPUT 1, 2 : VCR1 output
(Source 1)
MONITOR output : VCR2 output
(Source 4)
TV
DUBBING LOCK
OFF
OUTPUT 1, 2 : VCR1 output
(Source 1)
MONITOR output : VCR1 output
(Source 1)
20
-EN
Useful Tips (continued)
Component terminals
•Component connection is recommended when connecting a DVD player or DBS (equipped with component input terminals) to a TV.
Since a DVD disc is encoded with a component video (Y color difference) signal format it can reproduce better quality color than the composite or S-VIDEO signal used in a VCR.
With a component connection, the signal encoded on a DVD disc can be output in its original form to maintain the highest quality picture.
TV
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
Cr/Pr
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
: Signals
DVD Player
OPTICAL connector
•High quality digital audio recording is possible from a DVD player or DBS to an MD recorder using the JX-S555’s OPTI-
CAL connector.
An OPTICAL connector outputs the digital audio from a DVD player or DBS as an optical signal to maintain its purity.
DVD player
DBS
DBS
LEFT
AUDIO
RIGHT
1 2
INPUT
OPTICAL
4
Cr/Pr
OPTICAL
5
Cr/Pr
LEFT
AUDIO
RIGHT
Y Y
VIDEO
VIDEO
VICTOR COMPANY OF JAPAN, LIMITED. MADE IN JAPAN
Cb/Pb Cb/Pb
WARNING : SHOCK HAZARD-DO NOT OPEN
OUTPUT
1 2
MONITOR OUT
1 2
Y
OPTICAL LEFT
Cr/Pr
Cb/Pb
AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RIGHT
AUDIO
: Signals
MD compact system
EN-
21
Block Diagram
AUDIO
INPUT1
VIDEO/
S-VIDEO
AUDIO
INPUT2
VIDEO/
S-VIDEO
AUDIO
INPUT3 (FRONT)
VIDEO/
S-VIDEO
INPUT4
AUDIO
S-VIDEO
INPUT5
AUDIO
S-VIDEO
OPTICAL
INPUT4
AUDIO
COMPONENT
VIDEO
INPUT5
OPTICAL
AUDIO
COMPONENT
VIDEO
AUDIO
S-VIDEO
VIDEO
SOURCE
SELECT
S-VIDEO
(MONITOR)
S/V SELECT
Y/C
SEPARATOR
Y/C MIXER
S/V SELECT
S/V SELECT
VIDEO
(MONITOR)
AUDIO
(MONITOR)
Y/C
SEPARATOR
Y/C MIXER
S/V SELECT
COMPONENT VIDEO
(MONITOR)
SOURCE
SELECT
OPTICAL AUDIO
(MONITOR)
22
-EN
AUDIO
6 dB
S-VIDEO
LOOP
PROTECT
6 dB
VIDEO
6 dB
S-VIDEO
(MONITOR)
6 dB
VIDEO
(MONITOR)
AUDIO
(MONITOR)
6 dB
COMPONENT VIDEO
(MONITOR)
AUDIO
OUTPUT1
VIDEO/
S-VIDEO
AUDIO
OUTPUT2
VIDEO/
S-VIDEO
AUDIO
MONITOR
OUTPUT1
VIDEO/
S-VIDEO
AUDIO
S-VIDEO
MONITOR
OUTPUT2
COMPONENT
VIDEO
AUDIO
OPTICAL
AUDIO
AUDIO
EN-
23
Troubleshooting
• The JX-S555 incorporates a microcomputer, which may malfunction due to external interference or noise. If this trouble cannot be resolved by checking the items in the following table, reset the microcomputer by turning off the JX-S555, unplugging its power cord from the wall outlet, plugging it in again and then checking the operation.
Power
Symptom
No power
Cause
• Is the power cord disconnected from the AC outlet?
Remedy
• Insert the power plug firmly into the AC outlet.
Page
—
Unit cannot be turned
OFF
Playback Required picture won’t appear
• Make sure that the DUBBING LOCK function is set to ON.
• Press the POWER button after setting the DUBBING LOCK function OFF.
• Is the required video component connected to the corresponding INPUT/
OUTPUT terminals correctly?
• Is the monitor TV connected to the
MONITOR OUT terminals correctly?
• Check the connections again and reconnect correctly.
10,14
• Check the connections again and reconnect correctly.
20
10,14
The picture appears distorted during playback
• Is the LOOP PROTECT button pressed
OFF?
• Set the LOOP PROTECT button to ON.
11,19
Recording No picture recorded on the edited tape.
• Are the playback and recording VCRs connected correctly to the INPUT/
OUTPUT terminals? Also, is the correct SOURCE SELECT button selected?
• Is the DUBBING LOCK function set?
• Check the connections again and reconnect correctly before s e l e c t i n g the correct SOURCE SELECT button.
12,13
• Is the input select switch on the recording VCR set to the “AUX” position?
• Is the video input select switch on the recording VCR with S-VIDEO terminals set to the “S-VIDEO IN” position or “VIDEO input” position?
• Press DUBBING LOCK to OFF before pressing a SOURCE SELECT button.
• Set the input select switch on the recording VCR to “AUX”.
• Set the video input switch on the recording VCR to the correct position.
14, 20
13
13
— • Some video software may contain signals to prevent it from being copied. If you try to copy such a program, the results will not be viewable.
16 Dubbing operations are not possible when using equipment connected to the component terminal.
• Conversion is not possible from the component terminal to the S-VIDEO/
VIDEO terminals.
• Use the S-VIDEO terminal or connect a recording VCR to the MONITOR OUT
2 terminal.
No sound recorded on the edited tape
• Are the video components etc. connected to the AUDIO input terminals correctly?
• Check the connections again and reconnect correctly.
12
24
-EN
Symptom
Watching No picture displayed on TV
Cause
•Is the SOURCE SELECT button for the source component selected correctly?
•Is the TV connected properly to the
MONITOR output?
Remedy
•Check the pressed SOURCE SELECT button and press the correct button.
•Check the connection and connect it properly.
•Is the TV's input selector set correctly?
•Check the TV's input selector.
Page
10
10
11
Other
No picture displayed on TV with component input
Remote control not working
• Is a TV with a component input connected and set correctly?
• Check the component input correction by referring to the TV's instruction manual.
• Are the remote control batteries exhausted?
• Are the batteries inserted with correct polarity ( + and – )?
• Replace both batteries with new ones.
• Insert them correctly.
16
9
9
EN-
25
Specifications
Design and specifications subject to change without notice.
Product name
Input/output terminals
Video inputs
Video outputs
(Reference level)
Video crosstalk
Video S/N ratio
Video frequency response
Audio inputs
Audio outputs
Audio crosstalk
Audio S/N ratio
Audio frequency response
Distortion
Digital audio (OPTICAL)
Power requirements
Power consumption
Dimensions
Main body weight
Accessories
AV selector
Inputs:
Outputs:
Monitor outputs:
Audio monitor output:
OPTICAL output:
Reference level
• Composite signal Vp-p = 1.0 V (75 Ω)
• Component signals
Y:
Cb/Pb:
Cr/Pr:
Vp-p = 1.0 V (75 Ω)
Vp-p = 0.7 V (75 Ω)
Vp-p = 0.7 V (75 Ω)
Maximum input
• Composite signal Vp-p = 1.5 V (75 Ω)
• Component signals
Y:
Cb/Pb:
Cr/Pr:
Vp-p = 1.5 V (75 Ω)
Vp-p = 1.0 V (75 Ω)
Vp-p = 1.0 V (75 Ω)
• Composite signal Vp-p = 1.0 V (75 Ω)
• Component signals
Y:
Cb/Pb:
Cr/Pr:
Vp-p = 1.0 V (75 Ω)
Vp-p = 0.7 V (75 Ω)
Vp-p = 0.7 V (75 Ω)
50 dB or more (45 dB or more between Y/C in the same channel)
50 dB or more
5 lines (S-VIDEO, VIDEO, AUDIO L/R) x 3,
(Component, S-VIDEO, AUDIO L/R) x 2
2 lines (S-VIDEO, VIDEO, AUDIO L/R) x 2
2 lines (S-VIDEO, VIDEO, AUDIO L/R) x 1,
(Component, S-VIDEO, AUDIO L/R) x 1
1 line (AUDIO L/R) x 1
1 line (AUDIO)
Composite signal: 12 MHz, Component signals: 30 MHz
Reference level: –10 dBV (47 k Ω)
Maximum level: +6 dBV (1 kHz, 1% distortion)
–10 dBV (with reference input, 1 kHz)
80 dB or more (1 kHz)
80 dB or more
5 Hz to 50 kHz
Less than 0.03% (with reference input, 1 kHz)
Peak emission wavelength : 660 nm ± 30 nm
Peak output power : –15 dBm to –21 dBm
(at the output end of the reference optical fiber cable)
AC 120 V `, 60 Hz
13 W (2.0 W in Standby mode)
(W) 435 mm x (H) 84 mm x (D) 256 mm (including knobs, jacks, and feet)
(17-3/16" x 3-5/16" x 10-1/8")
2.8 k˝ (6.2 lbs)
Remote control unit (RM-AJ555), "AA" (R6/UM-3) battery x 2 (for operation testing)
26
-EN
Glossary
Multi-dubbing
Capability of using more than one VCR for dubbing by selecting any of them as the player and recorder.
S-VIDEO signal
Signal obtained by separating the composite video signal into the luminance and chrominance signals. This makes the video clearer with fewer blurs in the colors.
Composite video signal
Signal composed of the luminance (Y) and chrominance
(C) signals of the S-Video signals.
Component terminals
Means for transmission of high-quality video signals (Y/
Pb/Pr and Y/Cb/Cr) from a DVD player, etc. to a high-performance video monitor without interference between the signal components.
OPTICAL (digital) connector
Means for transmission of high-quality digital audio signal from a digital player component such as a CD player or a
DVD player to a digital recorder component such as an
MD recorder.
EN-
27
Index
Terms
A
AUDIO ........................................................................
7
C
Component terminals .................................
7, 21, 27
Composite video signal ......................................
7, 27
D
DUBBING LOCK ...................................
6, 8, 15, 20
L
LOOP PROTECT ..........................................
6, 8, 19
M
MULTI-DUBBING ....................................................
12
O
OPTICAL CONNECTOR ................................
16, 21
S
STANDBY ..................................................................
6
SOURCE SELECT ..............................................
6, 8
S-VIDEO signal ..................................................
7, 27
Y
Y/C separator ..........................................................
18
Y/C mixer ................................................................
18
28
-EN
VICTOR COMPANY OF JAPAN, LIMITED
䊚
2001 VICTOR COMPANY OF JAPAN, LIMITED
J
V
C
Printed in Japan
advertisement
Related manuals
advertisement
Table of contents
- 1 Cover
- 2 Safety Information
- 3 Contents
- 4 Major Features
- 5 System Configuration Example
- 6 Connectors, Controls and Indicators
- 9 Using the Remote Control Unit
- 10 Watching Video
- 12 Dubbing (Multi-dubbing)
- 14 Watching a Video Program While Recording Another one (Dubbing Lock)
- 16 Enjoy High-quality Video and Audio from a DVD (Optical connection)
- 18 Useful Tips
- 22 Block Diagram
- 24 Troubleshooting
- 26 Specifications
- 27 Glossary
- 28 Index
- 29 Back Cover