- Sports & recreation
- Fitness, gymnastics & weight training
- Treadmills
- Land Pride
- ALL SERIES
- Assembly Instructions
Landice 72070 Treadmill Assembly Instructions
Add to My manualsLand Pride Treker is an efficient and versatile piece of equipment designed to enhance your outdoor maintenance tasks. It boasts a cold weather kit that prevents carburetor icing on the Honda engine, making it ideal for operations in colder climates. To ensure optimal performance, the kit should be removed once temperatures consistently rise above 45 degrees Fahrenheit to avoid power loss. Keep in mind that the kit requires a warm-up period of approximately 4-5 minutes before full operation.
advertisement
Engine Cold Weather Kit
Assembly Instructions
Treker 4210/4410ST, 4200/4400ST & 4200/4400NT Manual No. 701-075M
Before You Start
!
When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it!
These optional assembly instructions contain only information required to assemble the Engine Cold
Weather Kit to the Trekers. A detailed Operator’s Manual was supplied with the Treker. Refer to the Operator’s
Manual for additional specific information especially information relating to safety concerns. Also included in the Operator’s Manual is important information on operation, adjustment, troubleshooting, and maintenance for this attachment (some manual sections do not apply to all options).
A separate Parts Manual for replacement parts can be purchased from your dealer or available free of charge at www.landpride.com. Have model and serial numbers handy when placing an order.
Manual Part Numbers:
• Operator’s Manual (All Series). . . . . . . . . .700-108M
• Parts Manual (4200/4400 NT/ST Series). . 700-108P
• Parts Manual (4210/4410 ST Series) . . . . 700-109P
General Information
The Engine Cold Weather Kits listed above are designed to prevent or eliminate effects of carburetor icing on the
20hp Honda engine used on the Land Pride Trekers.
Carburetor icing may occur at temperatures of
45 degrees Fahrenheit and lower. Typical symptoms will be loss of power, hard starting, engine backfiring, plug fouling, gas in the oil or engine stalling. Application of this kit will force warm air directly into the air intake filter reducing or eliminating the icing condition and its related symptoms. Vehicles being started at freezing temperatures should be allowed an engine and oil warmup period of approximately 4-5 minutes prior to full vehicle operation. When outdoor temperatures are consistently above 45 degrees Fahrenheit this kit must be removed or a noticeable power loss will
occur. If plugs have fouled and the dipstick indicates gas in the oil and an oil overfill condition, the oil and filter must be changed. Do not overfill with oil or plug fouling will likely reoccur.
Tools Required (All Trekers)
•
1/2” Open-end or box-end wrench
•
1/2” Socket and driver
•
Straight blade screwdriver
Instructions for Your Vehicle
These assembly instructions apply to the Engine
Cold Weather Kit for the following options listed below:
701-074A
701-074A
701-073A
Treker 4210/4410 ST Series
Treker 4200/4400 ST Series
Treker 4200/4400 NT Series
For assembly instructions for your vehicle, see page 4 for
4200/4400 NT Series Trekers, page 3 for 4200/4200 ST
Trekers and page 2 for 4210/4410 ST Trekers.
For a detailed parts list of each assembly kit, see the bottom of the first page of instructions pertaining to your vehicle. Use the list as a checklist to inventory parts received. Please contact your local Land Pride dealer for any missing hardware.
Further Assistance
Your dealer wants you to be satisfied with your new
Engine Cold Weather Kit. If for any reason you do not understand any part of this manual or are not satisfied with the service received, the following actions are suggested:
1.
Discuss the matter with your dealership service manager making sure he is aware of any problems you may have and that he has had the opportunity to assist you.
2.
If you are still not satisfied, seek out the owner or general manager of the dealership, explain the problem and request assistance.
3.
For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address [email protected]
© Copyright 2005 Printed 11/23/05 ■ Manual No. 701-075M 1
Land Pride
Assembly Instructions for 4210/4410 ST Trekers
Assembly Instructions for
4210/4410 ST Trekers
Engine Cold Weather Kit No. 701-074A
General Information
Be sure to read all instructions and safety precautions on page 1 before installing the Engine Cold Weather Kit.
Installation Instructions
1.
Loosen the two stainless steel hose clamps securing the air intake hose.
2.
Remove air intake hose and save for later reinstallation when warmer weather prevails.
5.
Obtain flexible aluminum tube and, taking care not to deform it, expand the tube to approximately 14”.
Install one end on the canister air intake tube as shown.
6.
Secure in place with the stainless steel hose clamp.
Flexible
Aluminum Tube
SS Hose
Clamp
Air Intake
Hose
SS Hose
Clamp
SS Hose
Clamp
23804
Figure 7
3.
Install heat gathering shield over the engine exhaust manifold at the 90 degree bend as shown.
4.
Secure with muffler clamp, flat bar, and two nuts.
Muffler Clamp
Flat Bar
Air Cleaner
Canister
23806
Figure 9
7.
Install the other end on the heat gathering shield as shown.
8.
Secure in place with the stainless steel hose clamp.
Flexible
Aluminum Tube
SS Hose
Clamp
Heat Gathering Shield
Heat
Gathering
Shield
Engine Exhaust
Manifold
Figure 8
23805
23807
Figure 10
2
1
1
1
1
2
Treker 4210/4410 ST Series Engine Cold Weather Kit Part No. 701-074A
Qty.
Part No.
Part Description
701-075M
700-204H
700-267D
700-272D
800-259C
MANUAL - ENGINE COLD WEATHER KIT
HEAT GATHERING SHIELD
MUFFLER CLAMP FLAT BAR
2" FLEXIBLE ALUMINUM TUBE 18.0" LG
HOSE CLAMP WRM DRV#36SS (1.81-2.75)
Manual No. 701-075M ■ 11/23/05
Land Pride
Assembly Instructions for 4200/4400 ST Trekers
Assembly Instructions for
4200/4400 ST Trekers
Engine Cold Weather Kit No. 701-074A
General Information
Be sure to read all instructions and safety precautions on page 1 before installing the Engine Cold Weather Kit.
Installation Instructions
1.
Release retaining clips two places on bottom of air cleaner canister and remove air cleaner access cover.
NOTE: It is not necessary to disconnect engine snorkel.
5.
Obtain flexible aluminum tube and, taking care not to deform it, expand the tube to approximately 14”.
Install one end on the heat gathering shield and the other end on the canister air intake tube.
6.
Secure in place with the stainless steel hose clamps as illustrated.
7.
Reinstall the lower access cover to the air intake canister.
8.
Tighten driver’s side canister bolt.
Air Intake Tube
Before Rotation
Driver’s Side
Canister Bolt
Engine
Snorkel
214547
Figure 5
Air Cleaner
Canister
Access Cover
Engine
Snorkel Hose
Retaining Clip
21455
Flexible
Aluminum Tube
Figure 4
2.
Loosen driver’s side canister bolt and rotate canister until air intake tube is facing diagonally toward left front corner of the engine.
3.
Install heat gathering shield over the engine exhaust manifold at the 90 degree bend as shown.
4.
Secure with muffler clamp, flat bar, and two nuts.
SS Hose
Clamp
Heat
Gathering
Shield
SS Hose
Clamp
Figure 6
Air Filter
Intake Tube
Rotated
Muffler Clamp
Flat Bar
Engine Exhaust
Manifold
21453
1
1
1
1
2
Treker 4200/4400 ST Series Engine Cold Weather Kit Part No. 701-074A
Qty.
Part No.
Part Description
701-075M
700-204H
700-267D
700-272D
800-259C
MANUAL - ENGINE COLD WEATHER KIT
HEAT GATHERING SHIELD
MUFFLER CLAMP FLAT BAR
2" FLEXIBLE ALUMINUM TUBE 18.0" LG
HOSE CLAMP WRM DRV#36SS (1.81-2.75)
11/23/05 ■ Manual No. 701-075M 3
Land Pride
Assembly Instructions for 4200/4400 NT Trekers
Assembly Instructions for
4200/4400 NT Trekers
Engine Cold Weather Kit No. 701-073A
General Information
Be sure to read all instructions and safety precautions on page 1 before installing the Engine Cold Weather Kit.
Installation Instructions
1.
Loosen the stainless steel Hose Clamps securing the rubber air intake hose.
2.
Remove rubber air intake hose and save for later reinstallation when warmer weather prevails.
!
CAUTION!
Caution: Make sure the flexible aluminum tube does not come into contact with battery terminals. If necessary, secure the aluminum air intake tube safely away from the battery with a plastic tie strap.
3.
Install heat gathering shield over the engine exhaust manifold at the 90 degree bend as shown.
4.
Secure with muffler clamp, flat bar, and two nuts.
5.
Obtain flexible aluminum tube and, taking care not to deform it, expand the tube to approximately 40”.
Install one end on the heat gathering shield and the other end on the canister air intake tube.
6.
Secure in place with the stainless steel hose clamps as illustrated.
Flexible
Aluminum Tube
Engine Exhaust
Manifold
Muffler Clamp
Flat Bar
SS Hose
Clamp
Heat
Gathering
Shield
Figure 2
21457
SS Hose
Clamp
Canister Air
Intake Tube
Flexible
Aluminum Tube
SS Hose
Clamp
Battery
Terminals
Air Cleaner
Canister
Rubber Air
Intake Hose
Air Cleaner
Canister
21127
Figure 1
Figure 3
1
1
1
1
2
Treker 4200/4400 NT Series Engine Cold Weather Kit Part No. 701-073A
Qty.
Part No.
Part Description
701-075M
700-204H
700-267D
700-271D
800-259C
MANUAL - ENGINE COLD WEATHER KIT
HEAT GATHERING SHIELD
MUFFLER CLAMP FLAT BAR
2" FLEXIBLE ALUMINUM TUBE 36.0" LG
HOSE CLAMP WRM DRV#36SS (1.81-2.75)
4
21456
Manual No. 701-075M ■ 11/23/05
advertisement
Related manuals
advertisement