Planet Technology ICA-107P Digital Camera User's Manual
Add to my manualsadvertisement
Wired / Wireless / PoE
CMOS IP Camera
ICA-107
ICA-107W
ICA-107P
User’s Manual
Version: 1.00
Copyright © 2007 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, PLANET reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
4. Consult the dealer or an experienced radio technician for help
FCC Caution
To assure continued compliance. (example-use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions: ( 1 ) This device may not cause harmful interference, and ( 2 ) this Device must accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND
THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and
Satellite Earth Station Equipment) As of April 8,2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment .
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
WEEE Regulation
To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
User’s Manual for PLANET Wired / Wireless / PoE CMOS IP Camera
Model: ICA-107 / ICA-107W / ICA-107P
Rev: 1.0 (July. 2007)
Part No. EM-ICA-107_W_P
Contents
Wireless Settings (ICA-107W Only).............................................................18
10. Appendix A Router/Gateway Setup for Internet Viewing ................................... 70
11. Appendix B Viewing via UPnP in Windows XP.................................................. 72
12. Appendix D Configure Windows 2003 Server ................................................... 77
1. Introduction
Searching for a powerful and economical Internet Camera? PLANET is glad to introduce our ICA-107 / ICA-107W / ICA-107P. Those Internet Cameras Integrated a microcomputer and a high quality CMOS digital-Image-Sensor, enabling it to display high quality live streaming video over your LAN and the Internet.
The motion detection of the ICA-107 series can notify users via email or ftp when detecting any movement. With its admin software, no expertise required, your first surveillance network can be easily, efficiently established in few minutes.
ICA-107W support 802.11b/g wireless network, that will save your time and cost for wiring.
And ICA-107P has provided IEEE802.3af standard PoE interface, it helps you to locate the camera to any location that is no power outlet. With the Windows based utility, IP Camera
Viewer, the ICA-107 series could take a snapshot, record and playback the video files. Also with a powerful central manage system – Cam Viewer Lite, it can help you to manage all the
PLANET internet cameras in the same software, not just ICA-107 serial.
In the following section, unless specified, the term “IP Camera” will mean all the cameras above. For Cam Viewer Lite, you may check the manual in Cam Viewer Lite CD disk for the details.
1
Internet
Power
Camera Stand Kit
Category 5 Ethernet Cable
Quick Installation Guide
CD-Rom
External Antenna (ICA-107W only)
If any of the above items are missing, please contact your supplier.
2
Model
Network Environment
Network Access 10/ 100Base-TX Ethernet
Additional Interface - IEEE 802.11b/g IEEE 802.3af PoE
Monitoring System Recommendation
System Hardware • CPU: Pentium 4, 1.6GHz or above
• Memory Size: 256 MB (512 MB Recommended)
• VGA card resolution: 800 x 600 or above
Web Browser • Internet Explorer 6.0 or above
System Requirement for IP Camera Admin & Viewer
Support OS Windows 2000 SP4, Windows XP SP2
System Hardware 1 – 4 cameras surveillance application
• CPU: Pentium 4, 2.0GHz or above
• Memory Size: 256 MB or above.
• VGA card resolution: 1024x768 or above
3
4.1. LED and Focusing
The IP Camera head and its focus ring allow you to modify the aim and focus of the IP
Camera. To adjust the IP Camera’s focus, please rotate the focus ring.
There are LEDs indicating the IP Camera status and networking status. y Power
When the IP Camera is power on, the LED will light on. y WLAN (ICA-107W only)
When the IP Camera is linking with wireless interface, the LED will light on. This LED will flash when video is transmitting or receiving. y LAN
When the IP Camera is linking to wired interface, the LED will light on. This LED will flash when video is transmitting or receiving.
Antenna Connector
(ICA-107W only)
LAN LED: LAN
Activity
Wireless LED :
WLAN Activity
Power LED:
Power On
Focus Ring
Front view of IP Camera
(Example on ICA-107W )
4
y y y y
Power Input
The DC power input connector is located on the IP Camera's bottom panel, and is labeled 12V DC with a single jack socket to supply power to the IP Camera. Power will be generated when the power supply is connected to a wall outlet.
Ethernet Jack
The IP Camera's bottom panel features an RJ-45 connector for connections to
10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling (which should be
Category 5 twisted-pair cable). The port supports “Auto-MDIX” function, allowing the
IP Camera to automatically detect or negotiate the transmission speed of the network.
For ICA-107P, this port is also the PoE interface.
Antenna Connector (ICA-107W only)
ICA-107W provides a standard Reverse SMA connector on its top panel. The external antenna allows you to adjust its position to obtain the maximum signal.
Reset Button
1.
2.
Press the reset button (for less than 2 seconds) and the IP Camera will reboot.
Press the reset button for more than 5 seconds and the IP Camera will reset to the factory default. The factory default settings are listed in the table below.
Power Input Ethernet Jack Reset Button
Bottom View of IP Camera
(Example on ICA-107)
Factory Default Setting
IP Address
Default Account
Default Password
Default Http Port
Default Video Port
192.168.0.20
Admin
Admin
80
4321
5
Installation Procedure
1. Unpack the package and verify that all the items listed in the Chapter 2 are available.
2. Connect the IP Camera to your network with the attached network cable; please connect the IP camera to your network switch or router.
3. Connect the power adapter to IP Camera and plug the power adapter to power outlet. The
IP Camera will be powered on. When the IP Camera is ready, the Power LED will light on.
4. Make sure that you have installed the ActiveX utility.
Note : It is highly recommended to use the power adapter shipped with the IP Camera, do
NOT use any other power adapter from other sources. It may make the IP Camera damage.
6
Follow the steps below to install the utilities. The following installation is implemented in
Windows XP and the installation procedure is similar to Windows 2000.
1. Insert the CD shipped along with the IP Camera into your CD-ROM drive. The installation page should open with your default browser. If not, please double click on the
“default.htm” in the CD.
2. Click on the hyperlink “Install Administrator Utility”.
7
3. After clicking on the “Install Administrator Utility” hyperlink, the browser should prompt to download the installation program. Click on the “Run” button, the installation program should be started.
4. Click “Next” to start the installation.
8
5. Click on the “Change” button to choose the destination you wished to install the utility. If no specific requirement, leave the default setting and click “Next”.
6. Click “Install” to start installing the utility.
9
7. The system will install the program automatically.
8. Click “Finish” to complete the software installation.
10
9. After the installation, IP Camera Admin will launch automatically. It will start to search the
IP Cameras in your intranet and it will list all the available IP Cameras on the camera list.
Choose the one that you would like to configure and click “Setting Wizard” to processed.
Camera list
10. Please enter the default password “Admin” and click “OK” to login to the IP Camera’s setup page.
11
11. To let the IP Camera work, you should configure the IP Camera’s IP address as you want.
The utility will try to find an available IP address and recommend you using that address.
Besides work with the recommended IP, you may input the IP address manually. Please be aware that the IP address of the IP Camera must be in the same IP segment of your .
Click “Finish” to apply the configuration.
12. After press “Finish”, the camera will restart. Please wait for a minute. Then you may refer to next section to start the configure utility and setup your IP camera.
12
6. Using the IP Camera Admin
The IP Camera Admin allows users to search and setup the cameras located within the
Intranet. With the IP Camera Admin, users can view all the information about the selected IP
Camera; furthermore, it provides a setting wizard, which can guide users to add the IP
Camera to the network easily and promptly.
There are two ways to run the IP Camera Admin:
1. Click “Start”, select “Programs”→“IP Camera” →”Admin Utility” to run the utility.
2. Double click the IP Camera Admin icon ( ) on the desktop to run the utility.
Once the utility is started, it will search the available IP Cameras in your intranet. For further configurations, please refer to the following sections.
13
LAN
Auto Discover
Camera List
The IP Camera Admin will search all the available IP Camera within the network when you click on this button.
The name and setting status of the IP Camera will show in this list.
The “ ” icon means the configuration of the IP Camera is in the status of factory default.
The “ ” icon means the IP Camera has been configured before.
The “ ” icon means the camera is unknown.
Internet
Add and Delete Button
Information of Camera
Camera Information
The functions located in this area are reserved for future use.
All information about the selected IP Camera will display here.
The informat ion includes Firmware Version, Network Information,
IP Address, UPnP Setting, DDNS Setting, Resolution and E-mail
14
Camera Setting
Detail Setting
S etting Wizard s etting, etc.
You m ight use this function for further configuring the IP Camera, such as IP address, Resolution, password and firmware upgrad e, etc.
You might use this function to configure the camera name, IP address and the video port of the IP Camera.
15
After clicking on the “Detail Setting”, the IP Camera Admin will ask you to enter the
“Administrator Name” and “Password” for authentication. The default administrator name / password are:
Administrator Name: “Admin”
Password: “Admin”
After entering the password and clicking on the “OK” button, you could start to configure your
IP Camera.
16
Network Setting
DHCP
Camera Name
IP Address
Subnet Mask
Gateway
DNS Server
Video Port
Web Port
Enable or disable the DHCP function here.
It is recommended to name a meaningful name for the camera.
For example, “Living Room”, “Front Door”. That will help you to recognize the IP Camera more easily.
Please assign an available IP address to your IP Camera.
Please input the subnet mask that you want to use here.
Please input the gateway that you want to use here.
Please input the desired DNS server here.
The IP Camera uses the Video Port to transmit or receive the video streaming. The default port is “4321”.
The default port used by the web is 80. You might use a different port for the web of the IP Camera. If you change this to another port number, for example, 8080, then you are required to use this
17
dedicated port to access the web page, for example: http://192.168.0.20:8080.
10F Planet
The IP Camera Admin will find available wireless network automatically. You could also press the “Refresh” button to find the available wireless network manually.
After refresh procedure, there will show the available wireless networks.
18
10F Planet
You might press “Connect” for connecting to the AP directly or “Add to Profile” to configure the security setting of the wireless network.
10F Planet
ICA-107W supports WEP (Open System/Shared Key), WPA-PSK, WPA2-PSK and WPANone.
Please select the responding security setting of the desired wireless network. After set the profile, you might remove the LAN cable, and the IP Camera will connect to the AP automatically. When the connection es tablished, you wi ir light on.
19
LED Status Diagram
Wired Setting Environment Wireless Setting Environment a.) You should configure the wireless settings via the wired connection when you first time to set the ICA-107W to wireless interface. b.) After the configuration is done, you might remove the cable then the wireless connection should start automatically.
20
6.2.3. E-M Setting
E-Mail Setting
Recipient E-Mail Address You can snapshot a picture and send the picture by E-Mail. Enter
SMTP Server
Sender E-Mail Address
Authentication
Username the E-Mail Account for receiving the picture.
Enter the SMTP Server for the E-Mail sending.
Specified the e-mail address of sender.
Enable or Disable the SMTP Authentication function
When E-Mail Authentication is enabled, please input the SMTP
Username here.
Password
Send a Test Email
When E-Mail Authentication is enabled, please input the password here.
Press this button to send a test e-mail to your mailbox. You can use this function to test if your setting is correct.
21
PPPoE Settings
Enable/Disable
Username
Password
MTU
Enable or Disable the PPPoE connection here.
Enter the Username of your PPPoE account.
Enter the Password of your PPPoE account.
Maximum Transmission Unit (MTU) is the largest frame that could be transmitted through the PPPoE connection. The MTU is specified in octets (eight-bit bytes). If there is no other request, please leave it as default value.
22
FTP Settings
FTP Server
FTP Port
User Name
Password
Remote Folder
Passive Mode
The IP Camera could upload picture to the FTP server when you enable the motion detection function. Please enter the IP address of the FTP server that you want to use.
Please enter the FTP port number that your FTP server uses. In most case, the FTP server should use TCP port 21.
Specify the user account of ftp server.
Specify the password of your ftp account.
Specify the folder of the ftp site that you want to store the video.
If your IP Camera is under NAT, you usually need to enable this feature.
23
6.2.6. Date / Time Settings
Date / Time Settings
Set Date/Time manually Set the current Date and Time here.
NTP Server
Time Zone
NTP Server
Enable or Disable the NTP client here.
Select your time zone here.
Specify the IP address of the NTP server.
24
6.2.7. Resolution
Resolution
Resolution You might select the desired video resolution here. Available resolutions are: 176 x 144, 320 x 240, 640 x 480.
25
Advanced Setting
UPnP
Enable/Disable DDNS
Provider
Domain Name
Account
Password
Enable or Disable UPnP here.
Enable or disable DDNS function of the IP Camera.
The IP Camera supports the service from DynDNS, for further information, please refer to: http://www.dyndns.org
The domain name given by DynDNS is
“registername.dyndns.com”. Please enter the domain name that you register for the IP Camera from DynDNS web site.
Enter the login name for the DDNS service.
Enter the password for the DDNS service.
26
6.2.9. Users
Users
Administrator
Current Password
New Password
Setting the password of Administrator account
Enter the current password of the IP Camera.
Enter the new password you want to use for the IP Camera.
Confirm New Password Retype the new password to confirm the setting.
User You might Enable/Disable the user accounts and setting the user name and password here. The IP Camera could support up to 4 user accounts.
27
6.2.10. Tools
Tools
Firmware Version
Firmware Update
Reset to Default
Display current firmware version.
You could upgrade IP Camera’s firmware via this function. Press this button and select the correct firmware to upgrade.
If you want to reset the IP Camera to factory default, you might click on this button. The default settings of the IP Camera are as follows.
Camera Name: “ICA-107(W / P)”
IP Address: “192.168.0.20”
Subnet Mask: 255.255.255.0
Administrator Name: “Admin”
Password: “Admin”
Video Port: “4321”
28
LED Light ON/OFF
6.2.11. About
Web Port: “80”
You might turn all the IP Camera’s LEDs ON/OFF via this button.
It can let the people don’t know this camera is monitoring.
About
Administrator Utility
Version
Display current Administrator Utility Version.
29
When you click the “Setting Wizard”, the IP Camera Admin will ask you to enter the
“Administrator Name” and “Password”. The default value is as follows.
Administrator Name: “Admin”
Password: “Admin＂
If the name and password you entered are correct, you can start to setup the camera.
Network Setting
Camera Name
IP Address
Subnet Mask
It is recommended to name a meaningful name for the camera.
For example, “Living Room”, “Front Door”. That will help you to recognize the IP Camera more easily.
Please assign an available IP address to your IP Camera.
Please input the subnet mask that you want to use here.
30
Gateway
DNS Server
Please input the gateway that you want to use here.
Please input the desired DNS server here.
After you finish the camera setting, the IP Camera Admin will ask if you want to start the IP
Camera Viewer. You could click on “Ok” to run the IP Camera Viewer immediately or click on
“Cancel” to run the IP Camera Viewer later.
31
7. Using the Camera Viewer
The IP Camera Viewer allows users to view video up to four IP Cameras at the same time. It also allows users to manual/schedule recording video and playback the video file. The status of cameras such as frame rate, video received, and etc are also displayed on the screen at the same time.
There are three ways to run the IP Camera Viewer:
1. Click “Start”, select “Programs”→”IP Camera”→”Camera Viewer” to run the utility.
2. Double click on the IP Camera Viewer icon ( ) to run the utility.
3. Click “Setting Wizard” from IP Camera Admin and follow the instructions to launch the IP
Camera Viwer.
32
7.1. Introduction to the Control Panel
When you start the IP Camera Viewer, you would see a Control Panel and the Viewer window.
Control Panel
Viewer Window
33
Camera Buttons
Camera Please click on one of these number buttons for connecting to the selected IP Camera. If you want to remove the camera from the
IP Camera Viewer, please right click on the icon and select
“Reset Camera x”. If you want to modify the channel setting, please right click the icon and select “Configure Camera x”.
34
Above the Number button, there are status bars that will indicate the different status of the IP
Camera. Please refer to the table below to check the status of your IP Camera.
Camera Status
Yellow
Blue
Pink
Red
Control Buttons
Play
Stop
Pause
The channel has not been configured yet.
The IP Camera is connected and playing the live video.
The IP Camera is not connected now.
The IP Camera is recording.
Snapshot Pause
Stop Record Play
End the IP Camera
Viewer
Minimize the Window
Forward
In Display mode, clicking on the “Play” button, the IP Camera
Viewer will connect to the disconnected IP Camera. In Playback mode, clicking on the “Play” can play the video.
In the Display mode, clicking on the “Stop” button, the IP Camera
Viewer will disconnect the IP Camera. In the playback mode, clicking on the “Stop” can stop playing the video.
Clicking on the “Pause” button, the IP Camera Viewer will pause the current video display. You might use the “Play” button to
35
Forward
Snapshot
Record resume the video display.
Clicking on the “Forward” button to forward the speed when you play the recording file.
Clicking on the “Snapshot” button will make the IP Camera
Viewer to take a snapshot of the video and save the picture as a bitmap file in the hard disk. (You will learn how to set the directory for storing these bitmap files at the Section 7.8.4)
By clicking “Record” button you can record video immediately.
(You will learn how to set the directory for storing video files at the section 7.8.4)
36
The IP Camera Viewer allows you to record the video in the “.AVI” files. There are two ways of video recording – Manual Recording and Schedule Recording.
Manual Recording
You can manually record the video stream into an assigned video file.
Click “Record”, then the IP Camera Viewer will start to record the video stream. You can assign the path in the setting dialog.(please see section 7.8.4) Clicking “Stop” will stop recording.
Note: Before manual recording, you have to click the camera button to select the IP Camera that you want to record first and make sure that the IP Camera Viewer is successfully connecting to the IP Camera.
Schedule Recording
You can assign a schedule and let the IP Camera Viewer recording the video stream automatically. Please refer to Section 7.8 to see how to setup schedule for the recording. The file name of the recorded video file is the start time of recording. For example, the file name
“IPCamera_2006-10-8-23-56-40.avi” means it was recorded at 2006/10/8 23:56:40.
37
The IP Camera Viewer supports two resolutions, 640x480 (VGA) and 320x240 (CIF). You can change the resolution of each IP Camera by clicking the resolution button.
Note: Before changing the resolution of the IP Camera, you have to select the IP Camera by clicking the camera button first. If you change the resolution of an IP Camera, other clients who are viewing the same IP Camera will also see the video with the changed resolution.
Resolution
VGA
QVGA
Change the resolution to 640x480 (VGA).
Change the resolution to 320x240 (QVGA).
38
7.7. View Four Cameras Simultaneously
Click the four division button four-division window.
can view the 4 IP Cameras simultaneously in a
39
7.8. Viewer Utility Setting
Click the “Setting” button , the setting window of the IP Camera will pop up.
Note: If you want to change the settings such as IP Address, Video Port, etc. in the “Setting” option, you must disconnect the Internet Camera first. You might disconnect the IP Camera by clicking on the “Stop” button.
40
7.8.1. Setting
Setting
Name
IP Address
Video Port
Model
Username
Password
Discover
It is not required to fill the name of IP Camera for connecting. It is for users to identify the camera.
Enter the IP address of the IP Camera you want to connect here.
Enter the port number of the video streaming used by the IP
Camera here.
Select the Model Name of the IP Camera.
The user name for login into the IP Camera. By default, the user name is “Admin”.
The password for login into the IP Camera. The default value is
“Admin”.
Clicking on the “Discover” button, the IP Camera Admin will pop up. The window will show all the discovered cameras on LAN.
41
7.8.2. Recording
The IP Camera Viewer support schedule recording function. The IP Camera Viewer will record the video stream in the assigned file folder according to the schedule automatically.
The recorded video files are AVI format.
Note:
1. The IP Camera Viewer will only start to record the video stream when it is running and is successfully connecting to the Internet camera in the beginning of the schedule.
2. The schedule setting of one-time or weekly schedule should not overlap, or the recording will fail.
42
One-Time Schedule
Schedule
New
Edit
Delete
Schedule
Cycle Recording
One-Time Schedule
Weekly Schedule
Click “New” to add a new recording schedule.
Select an existing schedule in the schedule list and click “Edit” to edit the schedule.
Select an existing schedule in the schedule list and click “Delete” to delete the schedule.
Check this check box to enable cycle recording. When the Cycle
Recording is checked and the storage usage has already reached the maximum reserved storage space, the IP Camera
Viewer will automatically delete the oldest recorded video file and use the space to store the newly recorded video stream.
You can assign a period of time and the IP Camera Viewer will
43
Weekly Schedule automatically record the video stream only during the period of time. The default time is 2 minutes later from the current time.
You can select the days in a week and set a period of time that you want to record the video stream.
7.8.3. Status
You can see the current status of the connection session between the IP Camera Viewer and the IP Camera.
Status
Connected
Status
Stream Started At
Time Elapsed
“Yes”: When the IP Camera Viewer is connecting to the IP
Camera.
“No”: When the utility is not connecting to the IP Camera.
The starting time of the current connection between the IP
Camera Viewer and the IP Camera.
The elapsed time of the current connection between the IP
44
Video Received
Audio Received
Frame Rate
Data Rate
Number of Frames
Number of Users
Camera Viewer and the IP Camera.
The total size (Unit is KByte) of video stream received from the IP
Camera.
(Reserved for future use.)
The fps (frames per second) of the current video stream.
The data rate (KByte per second) of the current video stream.
The total number of video frames received during the current connection session between the IP Camera Viewer and the IP
Camera.
The total numbers of user that is viewing this camera.
45
7.8.4. General
You can manage storage usage for the IP Camera here.
General
Snap Shot Directory
Record Directory
Free Disk Space
Max Recording Space
Used Disk Space
Max Video File Size
This function lets you assign the directory where snapshot image will be stored. The default folder is where the IP Camera Viewer is installed, for example: “C:\Program Files\Internet Camera”.
This function lets you assign the directory where the recorded video files stored. The default folder is where the IP Camera
Viewer is installed, for example: “C:\Program Files\Internet
Camera”.
The current free disk space of the hard drive that is assigned to save recording files.
You can reserve a disk space to store the recorded video and snapshot files. If the space is run out, a message will pop up to remind you.
The current used disk space for saving the recording file.
This function let you assign a maximum size of each video file.
The max value is 2 GB per file.
46
7.8.5. About
About
Camera Viewer Utility
Version
Display current version of IP Camera Viewer.
47
7.9. Playback
Click the “Open File” and the “Load File” window will be popped up. Select the file that you want to play.
The IP Camera Viewer will start to play the selected video file.
48
Playing Control
Play
Pause
When the video playback is in Stop state, click on the “Play” button and the IP Camera Viewer will play the video file from the beginning point. When the video playback is in Pause state, click on the “Play” button and the IP Camera Viewer will play the video file from the current pause point. When the IP Camera Viewer is playing with fast speed, just click “Play” button to let the IP
Camera Viewer play with the normal speed.
When the recorded video is playing, you can click the “Pause” button to freeze the playback. If you want the IP Camera Viewer
49
Stop
Playing Control
Forward to continue playing from the current pause point, just click “Play”.
When the IP Camera Viewer is playing, you can click “Stop” to stop the playback. If you want the IP Camera Viewer to play again, just click “Play” and the IP Camera Viewer will play the video file from the beginning point.
If you want the IP Camera Viewer to play the video file in a faster speed, just click “Forward” and the IP Camera Viewer will double the playing speed. If you want the IP Camera Viewer play with the normal speed, just click “Play”.
50
Rotate function lets you rotate the video frame 180 of degree each time you click the “Rotate”
. With this function, you can view the live video with normal position or rotate with 180 degree.
51
8. Web Connection and Setup
You can use the Web browser to connect the IP Camera for viewing or setting. Open the web browser and enter the IP address of the IP Camera to establish a connection. The default IP address of the camera is “192.168.0.20”.
When the welcome screen appears, enter the “Administrator Name” and “Password”. The default values are:
Administrator Name: “Admin”
Password: “Admin”
When the IP Camera is connected, the browser will take you to the live video page. If you are viewing the IP Camera at the first time, the following dialog will appear to install the ActiveX plug in. Please check the publisher part; you should accept it, if it is published by PLANET
Technology Corp.
52
After installed the ActiveX plug-in, the video image will be shown up in the web screen directly.
(Example on ICA-107W)
The menu options for the web control screen are as follows.
Camera – View live video and adjust the video format from the menu.
LAN – Configure the LAN port.
WLAN – Configure the WLAN port. (ICA-107W Only)
E-Mail & FTP – Setup the E-Mail client and FTP client.
53
Motion Detection – Configure the Motion Detection here.
System – Configure the system settings here.
Status – Shows the camera information and current status in this page.
Users – The IP Camera support up to 4 user accounts. You can set those accounts here.
54
Camera Setting
Resolution
Image Quality
Max Frame Rate
Frequency
Brightness
Contrast
Saturation
Hue
(Example on ICA-107W)
Select the desired video resolution. Available resolutions are: 640 x 480, 320 x 240, and 176 x 144. The default resolution is CIF.
Adjust the video quality here.
Set the video max frame rate. This camera can support at most
30 frames per second.
Adjust this property to fitting light frequency.
You can adjust the brightness of the video. This value can be from 1 to 100.
You can adjust the contrast by change this value. This value can be from 1 to 100.
You can adjust the saturation by change this value. This value can be from 1 to 100.
You can adjust the hue by change this value. This value can be
55
Whiteness
Enable Auto Exposure
Apply from 1 to 100.
You can adjust the white balance by change this value. This value can be from 10 to 30.
You can enable Auto Exposure by check this box. IF this function is enabled, the Brightness, Contrast, Saturation, Hue and
Whiteness adjustment would not take effect.
When you finish the setting, click this button to validate the setting values.
56
LAN
Network Type
IP Address
Subnet Mask
Gateway
DNS Server
Video Port
(Example on ICA-107W)
The IP Camera can obtain IP via DHCP protocol or specified a static IP Address to it.
Enter an available IP Address within the range in your LAN.
The Subnet Mask field must match the subnet setting on your
LAN. For example: 255.255.255.0.
Please enter the default gateway of your LAN here.
Please enter your prefer DNS server here.
The Video Port is used to transmit or receive the video stream.
The default port setting is “4321”. If you want to view the video from the camera, the port setting should be correct.
57
Web Port
Apply
PPPoE
Enable PPPoE
User Name
Password
MTU
Apply
Dynamic DNS
Enable DDNS
Provider
Domain Name
User Name
Password
Apply
UPnP
Enable UPNP
Apply
The IP Camera support web connection, the default web port is
80. If you change the web port from 80 to other port, such as
8080, you must type http://192.168.0.20:8080 to connect the camera through the web browser.
When you finish the “LAN” configuration, click “Apply” to apply the setting.
Enable or disable PPPoE function of the IP Camera.
Enter the User Name for the PPPoE account.
Enter the Password for the PPPoE account.
Maximum Transmission Unit (MTU) is the largest frame that could be transmitted through the PPPoE connection. The MTU is specified in octets (eight-bit bytes). If there is no other request, please leave it as default value.
When you finish the “PPPoE” configuration, click “Apply” to apply the setting.
Enable or disable DDNS function of the camera.
Several companies provide DDNS service. The IP Camera supports the service from DynDNS company.
The domain name given by DynDNS is
“registername.dyndns.com”. Enter the domain name that you register for the camera from DynDNS web site.
Enter the login name for the DDNS service.
Enter the password for the DDNS service.
When you finish the “Dynamic DNS” configuration, click “Apply” to apply the setting.
Enable or disable UPnP function of the camera.
When you finish the “UPnP” configuration, click “Apply” to apply the setting.
58
8.3. WLAN (ICA-107W Only)
Wireless Setting
Wireless connection
Network Type
Available Networks
(Example on ICA-107W)
Enable or disable the wireless function of the IP Camera. By default, the function is disabled.
Infrastructure – This operation mode requires the presence of a
Wireless LAN Access Point or Router. All communication is done via the Access Point or Router.
Ad-Hoc – Select this mode if you want to connect to another wireless stations in the Wireless LAN network without through an
Access Point or Router.
Select the networks listed below and click apply to connect to the specified network.
59
SSID
Channel
Basic Rate
Authentication and
Encryption Type
WPA Pre-Shared Key
WEP Key Length
WEP Key Format
Default Key
Key1 ~ Key4
Apply
The SSID (up to 32 printable ASCII characters) is the unique name identified in a WLAN. The ID prevents the unintentional merging of two co-located WLANs.
You may specify a SSID for the IP Camera and then only the device with the same SSID can interconnect to the IP Camera.
This setting is only available for Ad Hoc mode. Select the number of the radio channel used for the networking.
The IP Camera will force to the data rate that you selected to transmit data.
Choose the security setting of your wireless network.
The ICA-107W supports: “None”, “Open System”, “Shared Key” and “WPA-PSK”. When you select “WPA-PSK” authentication, you can encryption your wireless with WPA-TKIP or WPA-AES.
The WPA-PSK key can be from 8 to 64 characters and can be letters or numbers. This same key must be used on all of the node in the wireless network.
You may select 64-bit or 128-bit to encrypt transmitted data.
Larger key length will provide higher level of security, but the throughput will be lower.
Hexdecimal – Only “A-F“, “a-f“ and “0-9“ are allowed to be set as
WEP key.
ASCII – Numerical values, characters or signs are allowed to be
WEP key. It is more recognizable for user.
Select one of the keys (1~4) as the encryption key.
Enter the WEP key you want to use here.
When you finish “WLAN” configuration, click this button to apply the setting.
60
8.4. E-Mail and FTP
The “E-Mail & FTP” lets you setup E-Mail client and FTP client that camera can sent image to your e-mail account or FTP server when Motion has been detected.
(Example on ICA-107W)
Email & FTP
Recipient E-Mail Address The IP Camera supports “Motion Detection” function. Enter the
SMTP Server
Sender E-Mail Address
SMTP Authentication
Username
E-Mail Account for receiving the alert mail.
Enter the SMTP Server for sending the E-Mail.
Specified the e-mail address of the e-mail sender.
Enable or Disable the SMTP Authentication function
When Authentication is enabled, please input the SMTP
Username here.
Password
Send a Test Email
When Authentication is enabled, please input the account password here.
Press this button to send a test e-mail. You can use this function
61
FTP Server
FTP Port
User Name
Password
Remote Folder
Password
Passive Mode to test if your setting is correct.
The IP Camera supports “Motion Detection” function. When
Motion Detection event occurred, you can record the pictures to
FTP server. Enter the FTP address for uploading the pictures.
Enter the FTP port that the FTP server uses.
Specify the user account of ftp server.
Specify the password of your ftp account.
Specify the folder of the ftp site that you want to store the image.
When Authentication is enabled, input the account password.
If your IP Camera is behind the NAT, you usually need to enable this feature.
62
The “Motion Detection” allows users to setup the behavior of motion detection feature.
(Example on ICA-107W)
Motion Detection
Motion Detection Enable Enable or Disable the Motion Detection Function.
Next Event Detected
Interval
Setup the interval between two events. For example, if you setup the interval to 5 seconds, the next event will start after this event
Threshold
Send Recording File to
E-Mail finished + 5 seconds.
Setup the sensitivity of motion detection.
Select “Yes” to send the alert email with the recorded image to the e-mail account that you had specified in the “E-Mail & FTP”
E-Mail Subject page.
Specify the subject of motion detection alert e-mail.
Send snapshot file to FTP Select “Yes” to send the recorded video file to your FTP server that you had specified in the “E-Mail & FTP” page.
63
8.6. System
The “System” allows users to setup the IP Camera’s parameters, like camera name, data/time setting. And also provide firmware upgrade and reset tools at this page.
(Example on ICA-107W)
System
Camera Name
Password
The default camera name is “ICA-107(W / P)”. It is recommended to name a meaningful name for the IP Camera.
Enter the password for the default account. The password should be 4 digits.
Confirm Password
Set Date/Time manually and Synchronize to PC time
Enter the password again to confirm the setting.
You can set the IP Camera’s Date/Time manually. Or you can just click on the Synchronize to PC time to let the IP Camera synchronize its time to your PC automatically.
NTP Server (Radio Box) To enable the NTP function.
Time Zone Select the time zone where your camera is located.
NTP Server Specify the IP Address of the NTP Server here.
64
Upgrade Firmware You can upgrade the IP Camera’s firmware via this function.
Press the browse button, find the correct firmware and press upgrade.
Reset to Factory Defaults If you want to reset all the settings to factory default, please use
Reboot Device
LED Setting this function to fulfill your task.
To reboot the IP Camera, click “Reboot”.
If you wan to secure the IP Camera from noticing, you can turn off the LED light by clicking “LED Light OFF”. To turn on the LED light, just click “LED Light ON”.
65
8.7. Status
The “Status” shows the current firmware version, uptime, system time and IP information of this camera.
(Example on ICA-107W)
66
8.8. Users
The “Users” allows you to add four user accounts which are able to view video from the IP
Camera Viewer and Web Management. These users, unlike Administrator, are not allowed to configure the IP Camera.
User 1 / 2 / 3 / 4
User #
Login
Password
Confirm Password
Apply
(Example on ICA-107W)
Enable or Disable the user number #.
Enter the login name of the user account.
Enter up to 4 digits password for the new user account.
Enter the password again to confirm the setting.
Click “Apply” to save the user account setting.
67
8.9. Log
The “Log” allows users to monitor the device event and time. If you have trouble to use this device, the log file will help administrator to know the status of device.
Log
Log screen
Refresh
(Example on ICA-107W)
The screen will show event and event time of device.
You can press “Refresh” button to refresh the log screen.
68
Video specification
Max Resolution: 640 x 480 pixels
Sensor: 300K pixels 1/4" color CMOS sensor
Gain control: Automatic
Exposure: Automatic
White Balance: Automatic
Lens: Manual Focus, F=1.8
Image (Video Setting)
Image compression: MJPEG Image Video
Digital 24-bit Color
Frame rate: Up to 30fps
Video resolution: 176 x 144, 320x240, 640x480
System Hardware
LAN Connector: One RJ-45 port to connect to 10/100Mbps Ethernet
Wireless: IEEE 802.11b/g(ICA-107W Only)
PoE: 802.3af(ICA-107P Only)
LED Indicator: LAN LED, WLAN LED (ICA-107W Only), Power LED
Power Supply: 12V / 1A (ICA-107W)
Power Supply: 12V / 0.4A (ICA-107 / ICA-107P)
EMI & Safety
FCC, CE!
69
10. Appendix A Router/Gateway Setup for Internet
Viewing
To view IP Camera across the Internet, you have to make sure Router/Gateway has configured to pass incoming TCP/UDP connections from remote PC to the IP Camera. The
Router/Gateway should set port forwarding or virtual server for the connections. Please see the illustration as below.
Router/Gateway Port Forwarding/Virtual Server Setup
Name Protocol Port LAN
Setup 1
Setup 2
TCP
TCP
80
4321
192.168.0.20
192.168.0.20
Port Definition
Setup 1
Setup 2
It is the port of Web port. You have to configure the protocol to
“TCP”.
It is the port of Video port. You have to configure the protocol to
“TCP”.
Viewing Internet Camera via Web Browser
Setup 1/Setup 2 If you want to view the video via Web Browser from Internet, you have to ensure the Router/Gateway has configured both setup1 and setup 2. If the web port is not default port “80”, but changed to 8080. The remote user has to enter http://210.66.155.85:8080.
Without Setup 2, you will not see the video streaming in this PC.
Viewing Internet Camera via Camera Viewer Utility
Setup 2 If you want to use IP Camera Viewer Utility to view the camera from Internet, please make sure the Router/Gateway has
70
configured Setup2.
71
11. Appendix B Viewing via UPnP in Windows XP
When the UPnP function is enabled, the camera can be detected by UPnP compliant system such as Windows XP. The camera will be displayed in My Network Place, so you can double click the camera or right click the camera and select “Invoke” to view the video through web browser.
72
Enable UPnP in Windows XP SP2
If you can’t find the IP Camera in the My Network Place or you have seen the following message when you double click the IP Camera. You have to check if UPnP function is blocked by the firewall. Please follow the steps below to enable it.
1. Go to “Start\Settings\Network Connections”.
2.
3.
Right click the “Local Area Connection” and select “Properties”.
In the “Local Area Connection Properties”, select “Advanced” option menu and click
“Settings”.
73
4. The “Windows Firewall” screen will be popped up, select “Exceptions” option menu.
74
5. Enable “UPnP Framework” from the “Programs and Services list” and click “Ok”.
75
76
12. Appendix D Configure Windows 2003 Server
Graphics Hardware Acceleration and DirectX are disabled by default on a Server configuration to ensure maximum stability and uptime. But for any reason you need to enable them to use DirectX enabled applications this section will guide you through on how you can do it.
Enabling Graphics Hardware Acceleration
1. Simply right click anywhere on your desktop and select Properties -> Settings tab ->
Advanced -> and finally, the Troubleshoot tab.
2. Now move the Hardware acceleration slider across to Full
4. You may experience a monitor black out for a few seconds, this is normal.
77
Enabling DirectX
5. Click on Start -> Run -> and type dxdiag followed by enter. You will get a dialog bo x asking if you want to allow d xdiag to access the internet to check for valid WHQL certificates - click on Yes.
6. Let's click on the Display tab, now and AGP Texture Acceleration.
click on all three boxes to enable DirectDraw, Direct3D
78
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project