advertisement
SyncMaster 205BW
Install drivers Install programs
Notational
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.
Prohibited
Do not disassemble
Do not touch
Important to read and understand at all times
Disconnect the plug from the outlet
Grounding to prevent an electric shock
Power
When not used for an extended period of time, set your computer to DPMS.
If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug. z
This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. z
This may cause an electric shock or fire.
Use only a properly grounded plug and receptacle. z
An improper ground may cause electric shock or equipment damage.
Insert the power plug firmly so that it does not come loose. z
A bad connection may cause fire.
Installation
Do not excessively bend the plug and wire nor place heavy objects upon
them, which could cause damage. z
This may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet. z
This may cause fire.
Do not disconnect the power cord while using the monitor. z
A surge may be caused by the separation and may damage the monitor.
Do not use the power cord when the connector or plug is dusty. z z
If the connector or plug of the power cord is dusty, clean it with a dry cloth.
Using the power cord with a dusty plug or connector may cause an electric shock or fire.
Be sure to contact an authorized Service Center, when installing your monitor in a location with the heavy dust, high or low temperatures, high humidity, chemical substance and where it operates for 24 hours such as the airport, the train station or etc.
Failure to do so may cause a serious damage to your monitor.
Put your monitor in a location with low humidity and a minimum of dust. z
Failure to do so may cause an electric shock or fire inside the monitor.
Do not drop the monitor when moving it. z
This may cause damage to the product or human body.
Install the monitor base in a showcase or shelf so that the end of the
base does not protrude from the showcase or shelf. z
Dropping the product may cause damage to the product or personal injury.
Do not place the product on an unstable or small surface area. z
Place the product on an even, stable surface, as the product may fall and cause harm to someone walking by, specifically children.
Do not place the product on the floor. z
Someone, specifically children could trip over it.
Keep any flammable objects such as candles, insecticides or cigarettes away from the product. z
Otherwise, this may cause a fire.
Keep any heating devices away from the power cable. z A melted coating may lead to electric shock or fire.
Do not install the product in places with poor ventilation, for instance, a
bookshelf, closet, etc. z
Any increase in internal temperature may cause fire.
Set down the monitor carefully. z
The monitor could be damaged or broken.
Do not place the monitor face down. z
The TFT-LCD surface may be damaged.
Installing a wall bracket must be done by a qualified professional. z z
Installation by unqualified personnel may result in injury.
Always use the mounting device specified in the owner's manual.
When installing the product, make sure to keep it away from the wall
(more than 10 cm/4inch ) for ventilation purposes. z
Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.
Keep the plastic packaging (bag) out of children’s reach. z The plastic packaging (bag) may cause suffocation if children play with it.
Clean
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.
Do not spray water or detergent directly on the monitor. z This may cause damage, electric shock or fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. z
A dirty connector may cause an electric shock or fire.
Make sure to unplug the power cord before cleaning the product. z
Otherwise, this may cause electric shock or fire.
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. z Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent.
Contact the Service Center or Customer Center for interior cleaning once a year. z
Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire.
Others
Do not remove cover (or back). z z
This may cause an electric shock or fire.
Refer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service . z
This may cause an electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. z z
This may cause malfunction, an electric shock or fire.
Especially avoid operating the monitor near water or outdoors where it
could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center . z The monitor may malfunction, causing an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. z
Failure to do so may cause an electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable. z
This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable. z
This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not cover the vents on the monitor cabinet. z
Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on the monitor. z z
This may cause malfunction, an electric shock or fire.
If a foreign substance enters the monitor, unplug the power cord and contact the Service Center .
Keep the product away from combustible chemical sprays or inflammable substances. z
This may cause an explosion or fire.
Never insert anything metallic into the monitor openings. z This may cause an electric shock, fire or injury.
Do not insert metal objects such as chopsticks, wire and gimlet or inflammable objects such as paper and match into the vent, headphone port or AV ports. z
It may cause a fire or an electric shock. If an alien substances or water flows into the product, turn the product off, unplug the power connector from the wall outlet and contact Service Center .
If you view a fixed screen for an extended period of time, residual image or blurriness may appear. z Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time.
Adjust the resolution and frequency to the levels appropriate for the model. z Inappropriate resolution may cause undesirable picture quality.
20 inch (51 cm) - 1680 X 1050
Watching the monitor continuously at a too close angle may result in
eyesight damage.
To ease eye strain, take at least a five-minute break after every hour of
using the monitor.
Do not install the product on an unstable, uneven surface or a location
prone to vibrations. z Dropping the product may cause damage to the product or personal injury. Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire.
When moving the monitor, turn off and unplug the power cord.
Make sure that all cables, including the antenna cable and cables connecting to other devices, are disconnected before moving the monitor. z
Failure to disconnect cables may damage it and lead to fire or an electric shock.
Place the product out of children’s reach, as they could damage it by hanging onto it. z A falling product could cause physical damage even death.
When not using the product for an extended time period, keep the product unplugged.
z
Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, leading to electric shock or fire.
Do not place children’s favorite objects (or anything else that may be tempting) on the product. z
Children may try to climb on the product to retrieve an object. The product could fall, causing physical damage or even death.
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer .
Contact a local dealer to buy optional items.
Unpacking
Manual
Monitor & Sliding Stand
Cable
Quick Setup Guide
Warranty Card
(Not available in all locations)
User's Guide,
Monitor Driver,
Natural Color software,
MagicTune™ software
Front
D-sub Cable Power Cord DVI Cable (option)
MENU button [ ]
MagicBright™
[ ]
Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.
MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom,
Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.
1) Custom
Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.
If this is the case, adjust the brightness and contrast by using the OSD menu.
2) Text
For documentations or works involving heavy text.
3) Internet
For working with a mixture of images such as text and graphics.
4) Game
For watching motion pictures such as a game.
5) Sport
For watching motion pictures such as a sport.
6) Movie
For watching motion pictures such as a DVD or Video CD.
>>Click here to see an animation clip
Brightness button When OSD is not on the screen, push the button to adjust
Rear
[ ]
Adjust buttons [ brightness.
] Adjust items in the menu.
Enter button [ ] /
Source button
Activates a highlighted menu item. /
Push the ' ', then selects the video signal while the OSD is off.
(When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.)
Note : If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable.
Use this button for auto adjustment.
AUTO button
Power button [ ]/
Power indicator
Use this button for turn the monitor on and off. /
This light glows blue during normal operation, and blinks blue once as the monitor saves your adjustments.
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
(The configuration at the back of the monitor may vary from product to product.)
POWER IN
DVI IN
RGB IN
Connect the power cord for your monitor to the power port on the back of the monitor.
Connect the DVI Cable to the DVI port on the back of your monitor.
Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
Switch the monitor on and off. ON [ | ] / OFF [O]
Kensington Lock The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately. )
For using a locking device, contact where you purchase it.
See Connecting the Monitor for further information regarding cable connections.
Connecting the Monitor
1.
Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
2-1.
Using the D-sub (Analog) connector on the video card.
Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
[ RGB IN ]
2-2.
Using the DVI (Digital) connector on the video card.
Connect the DVI Cable to the DVI Port on the back of your Monitor.
[ DVI IN ]
2-3.
Connected to a Macintosh.
Connect the monitor to the Macintosh computer using the D-sub connection cable.
2-4.
In the case of an old model Macintosh, you need to connect the monitor using a special Mac adapter (Option).
3.
Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Using the Stand
Sliding Stand
A.Stand Stopper
Attaching a Base
This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.
A. Monitor
B. Mounting interface pad (Sold separately)
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
3. Remove four screws and then remove the stand from the LCD monitor.
4. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
Installing the Monitor Driver (Automatic)
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site shown here. z
Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)
Windows ME
1. Insert CD into the CD-ROM drive.
2. Click "Windows ME Driver".
3. Choose your monitor model in the model list, then click the "OK" button.
4. Click the "Install" button in the "Warning" window.
5. Monitor driver installation is completed.
Windows XP/2000
1. Insert CD into the CD-ROM drive.
2. Click "Windows XP/2000 Driver"
3. Choose your monitor model in the model list, then click the "OK" button.
4. If you can see following message window, then click the "Continue Anyway" button.
Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung
Monitor homepage http://www.samsung.com/ .
5. Monitor driver installation is completed.
Installing the Monitor Driver (Manual)
z
Windows XP | Windows 2000 | Windows Me | Windows NT | Linux
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site shown here.
Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)
Microsoft
®
Windows
®
XP Operating System
1. Insert CD into the CD-ROM driver.
2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.
6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/
9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed.
Microsoft
®
Windows
®
2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "Insert disk" window.
2. Click the "Browse" button on the "File Needed" window.
3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1. Click "Start" , "Setting" , "Control Panel".
2. Double click the "Display" Icon.
3. Choose the "Settings" tab and then click "Advanced..".
4. Choose "Monitor".
Case1: If the "Properties" button is inactive, it means your monitor is properly configured.
Please stop installation
Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually.
5. Click "Driver" and then click on "Update Driver.." then click on the "Next" button.
6. Choose "Display a list of the known drivers for this device so that I can choose a
specific driver" then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver).
8. Click the "Open" button, then click "OK" button.
9. Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes"button.
And click the "Finish" button then the "Close" button.
Microsoft
®
Windows
®
Millennium Operating System
1. Click "Start" , "Setting" , "Control Panel".
2. Double click "Display" icon.
3. Select the "Settings" tab and click "Advanced Properties" button.
4. Select the "Monitor" tab.
5. Click the "Change" button in the "Monitor Type" area.
6. Choose "Specify the location of the driver".
7. Choose "Display a list of all the driver in a specific location.." then click "Next" button.
8. Click the "Have Disk" button
9. Specify A:\(D:\driver) then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
Microsoft
®
Windows
®
NT Operating System
1. Click Start, Settings, Control Panel, and then double-click Display icon.
2. In Display Registration Information window, click Settings Tab and then click All Display
Modes.
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK.
4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency).
If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
1. Press Enter at the first and the second screen after executing the X86Config file.
2. The third screen is for setting your mouse.
3. Set a mouse for your computer.
4. The next screen is for selecting a keyboard.
5. Set a Keyboard for your computer.
6. The next screen is for setting your monitor.
7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)
8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window.
10. You have finished setting up your monitor.
Execute X-Window after setting other requested hardware.
Natural Color
Natural Color
One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics &
Telecommunications Research Institute (ETRI).
This system is available only for Samsung monitors and makes the color of the images on the monitor the same as the printed or scanned images.
For more information, refer to Help (F1) in the software program.
How to install the Natural Color software
Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural Color software.
To install the program manually, insert the CD included with the Samsung monitor into the CD-
ROM Drive, click the [Start] button of Windows and then select [Run...].
Enter D:\color\eng\setup.exe and then press the <Enter> key.
(If the drive where the CD is inserted is not D:\, enter the applicable drive.)
How to delete the Natural Color software program
Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a
program".
Select Natural Color from the list and then click the "Add/Delete" button.
1. [
]Use this button to open the on-screen menu and exit from the menu screen or close screen adjustment menu.
2. [ ]This button allows you to adjust items in the menu.
3. [ ]Press this button to activate a highlighted menu item.
4. [AUTO]Press to self-adjust to the incoming PC signal. The values of fine,coarse and position are adjusted automatically.
AUTO
Menu
AUTO
Locked
Description
When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center.
Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically.
(Available in analog mode only)
To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
- If auto adjustment does not work properly, press AUTO button again to adjust picture with more accuracy.
- If you change resolution in the control panel, auto function will be executed automatically.
Menu
Locked
Description
After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked).
You can adjust only the brightness and contrast of the monitor with the OSD adjustment locking feature.
MagicBright™
Menu Description
MagicBright™
Push the MagicBright button to circle through available preconfigured modes.
- Six different modes (Custom/Text/Internet/Game/Sport/Movie)
Brightness
Menu Description
Brightness
SOURCE
When OSD is not on the screen, push the button to adjust brightness.
Menu
SOURCE
Description
Selects the video signal while the OSD is off.
Picture
Color
Image
OSD
Setup
Information
Brightness
MagicColor
Coarse
Language
Contrast
Color Tone
Fine
H-Position
Color Control Gamma
Sharpness
V-Position
Auto Source Image Reset Color Reset
H-Position V-Position
Transparency Display Time
Picture
Menu
Brightness
Contrast
Color
Description
You can use the on-screen menus to change the brightness according to personal preference.
Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness.
[MENU → → → ,
You can use the on-screen menus to change the contrast according to personal preference.
[MENU → → , → MENU]
Play/Stop
Menu
MagicColor
Color Tone
Color Control
Gamma
Image
Description
MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality.
1) Off - Returns to the original mode.
2) Demo - The screen before applying MagicColor appears on the right and the screen after applying
MagicColor appears on the left.
3) Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
4) Intelligent - Displays vivid natural color with clearness.
[MENU → , → → MENU]
The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and
Custom.
[MENU → , → , → ,
Adjusts individual R,G,B color balance.
[MENU → , → , → , → MENU]
Gamma correction changes the luminance of the colors with intermediate luminance. z z z
Mode 1
Mode 2
Mode 3
[MENU → , → , → ,
Play/Stop
Menu
Coarse
Fine
Sharpness
H-Position
V-Position
OSD
Description
Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu.
(Available in analog mode only)
[MENU → , → → MENU]
Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed).
(Available in analog mode only)
[MENU → , → , → ,
Changes the clearance of image.
[MENU → , → , → ,
Changes the horizontal position of the monitor's entire display.
(Available in analog mode only)
[MENU → , → , → ,
Changes the vertical position of the monitor's entire display.
(Available in analog mode only)
[MENU → , → , → ,
Play/Stop
Menu Description
You can choose one of 9 languages.
Language
H-Position
V-Position
Transparency
Display Time
Setup
Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.
[MENU → , → → MENU]
You can change the horizontal position where the OSD menu appears on your monitor.
[MENU → , → , → ,
You can change the vertical position where the OSD menu appears on your monitor.
[MENU → , → , → ,
Change the transparency of the background of the OSD.
[MENU → , → , → ,
The menu will be automatically turned off if no adjustments are made for a certain time period.
You can set the amount of time the menu will wait before it is turned off.
[MENU → , → , → ,
Play/Stop
Menu
Auto Source
Image Reset
Color Reset
Description
Select Auto Source for the monitor to automatically select the signal source.
[MENU → , → → MENU]
Image parameters are replaced with the factory default values.
[MENU → , → , → ,
Color parameters are replaced with the factory default values.
[MENU → , → , → ,
Information
Play/Stop
Menu
Information
Description
Shows a video source, display mode on the OSD screen.
Overview | Installation | OSD Mode |
Color
Calibration
| Uninstall | Troubleshooting
Overview
What is MagicTune™?
Monitor performance can vary due to the graphics card, host computer lighting conditions and other environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique setting. Unfortunately, the manual controls available to tune the image often prove to be challenging. Proper adjustment (tuning) requires an easy to use program that goes through a step-by-step process to obtain the best overall picture quality.
In most cases even simple adjustments to Brightness, or Contrast require navigation of the multi-level, on-screen display (OSD) menus that are not easy to understand. Furthermore, there is no feedback to assist in correctly setting the controls of the monitor. MagicTune™ is a software utility that guides you through the tuning process with easy to understand instructions and back ground patterns designed for each monitor control. The display settings for each user can be saved, providing an easy way to select display characteristics in a multi-user environme or having a single user have multiple defined presets based on content and ambient lighting.
Basic Functionality
MagicTune™ is a software utility that allows monitor adjustment and color tuning using the Display Data
Channel Command Interface (DDC/CI) protocol. All adjustments to the display are controlled via software to eliminate the need to use the monitor on-screen display (OSD).
MagicTune™ supports Windows™ 98 SE, Me, 2000, XP Home, and XP Professional.
It is recommended using MagicTune™ in Windows™ 2000 or later.
MagicTune™ allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you.
OSD Mode
The OSD mode allows easy adjustment of monitor settings without taking pre-defined steps. You can access the desired menu item to set with ease.
Overview | Installation | OSD Mode |
Color
Calibration
| Uninstall | Troubleshooting
Installation
1. Insert the installation CD into the CD-ROM drive.
2. Click the MagicTune™ installation file.
3. Select installation Language, Click "Next".
4. When the Installation Shield Wizard window appears, click "Next."
5. Select "I accept the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicTune™ program.
7. Click "Install."
8. The "Installation Status" window appears.
9. Click "Finish."
10. When the installation is complete, the MagicTune™ executable icon appears on your desktop.
Double-click the icon to start the program.
MagicTune™ execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key.
Installation Problems
The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network environment.
See "Troubleshooting" if you have trouble during installation.
System Requirements
OS z z z z z
Windows™ 98 SE
Windows™ Me
Windows™ 2000
Windows™ XP Home Edition
Windows™ XP Professional
It is recommended using MagicTune™ in Windows™ 2000 or
later.
Hardware z z
32MB Memory above
25MB Hard disk space above
* For more information, visit the MagicTune™ website .
Overview | Installation | OSD Mode |
Color
Calibration
| Uninstall | Troubleshooting
MagicTune™ allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you. z z z
OSD mode may appear inconsistent with the explanation in guidance book depending on specification of each monitor.
When Rotation is functioning, portion of MagicTune™ program may not operate normally.
AutoRotation : The screens display will automatically rotate when the monitor is rotated. z z z
To execute Auto Rotation, it should be done as below.
Please install both MagicRotation and MagicTune™ 3.6 programs in your computer.
Launch MagicTune™ 3.6
Option → Preference → Click the small box in the enable task
tray menu. z z
MagicTune™ control mode will be different according to monitor models.
The permitted angle of rotation of the monitor is determined by the model of the monitor.
OSD Mode
The OSD mode makes the adjustment of settings on all monitors easy. When selected , each tab on top of the control window displays the general descriptions of the sub-menu items for adjustment.
When selected, each tab displays a list of menus. For quick adjustment of the monitor settings, the OSD mode allows easy and convenient access to all tabs and sub-menu items.
Button Tab Definition
OK
Reset
Cancel
Applies any changes made and exits MagicTune™.
Restores the display settings to the factory settings.
Exits MagicTune™ without applying the changes made. If you have not made any changes in the control window, clicking "Cancel" does not cause any actions.
Picture Tab Definition
Allows the user to adjust the screen settings to the desired values.
Brightness
Makes the entire screen brighter or darker. The detailed data of the images in the dark areas can be lost if the brightness is not adjusted to the proper level. Adjust the brightness for best viewing conditions.
Contrast
Adjusts the difference in brightness between the bright and dark areas on screen. Determines the crispness of the images.
Resolution
Lists all display resolutions supported by the program.
MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Text, Internet,Game, Sport,
Movie and Custom. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright control buttons.
MagicBright™
1. Text: For documentations or works involving heavy text.
2. Internet: For working with a mixture of images such as text and graphics.
3. Game : For watching motion pictures such as a Game.
4. Sport : For watching motion pictures such as a Sport.
5. Movie: For watching motion pictures such as a DVD or Video CD.
6. Custom: Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the
Brightness and Contrast by using the OSD menu.
MagicBright control mode will be different according to monitor models.
Some monitor will only support Four modes(Text, Internet, Entertain, Custom)
Color Tab Definition
Adjusts the "warmth" of the monitor background or image color.
MagicColor and Gamma will be shown only in the monitor that supports these functions.
Color Tone
The tone of the color can be changed. z z
Warm2 - Warm1 - Cool 1 - Cool 2 - Cool 3 - Cool 4 - Cool 5 - Cool 6 - Cool 7
Off
Color Tone mode will be different according to monitor models.
Some monitor will only support Four modes( Warm, Normal, Cool, Custom)
Adjusts of the monitor image color.
You can change the monitor color to your desired color.
Color
Control z
R- G - B
The process through which the colors of your choice are optimized and maintained. You will find
Calibration MagicTune™ extremely useful if you are one of those who wish to view images with their full details accurately reproduced - including web images and ones produced by a digital camera or scanner.
MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality.
1. OFF : Returns to the original mode.
2. DEMO : The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left.
3. Full : Displays not only vivid natural color but also more realistic natural skin color with clearness.
4. Intelligent : Displays vivid natural color with clearness.
5. MagicZone
{
The MagicZone ensures the clear and sharp display of animated multimedia or photo
MagicColor
{
{
{
{ images by enhancing the brightness, sharpness, saturation, Hue of a certain area on the screen. This offers an easy-to-use interface that highlights the video-playing portion of your multimedia program by automatically detecting and highlight the desired area by dragging.
When the mouse cursor is activated( )and it is necessary to de-activate it to use it for other tasks, right click your mouse, or put the activated cursor ( )on the taskbar and click. When de-activated, the icon on the screen changes back to the one shown before activation.
Especially, MagicZone is appropriate to using the moving picture.
Auto Detect : If you run the Movie in some players, MagicZone will automatically get the play screen highlighted (it will be supported in players of Gom, Adrenalin, KCP,
Window Media, and Power DVD etc., )Some other players also can be highlighted but could have some problems.
Tusk menu
HUE Adjust the tint of the color.
Saturation Adjusts the color saturation.
Brightness Adjusts the Brightness.
Sharpness
Adjusts the difference between the lightest and darkest areas of the display.
Zone Off Turn off the zone that you have captured.
Reset Returns to the the default setting that vendor has set. z z z
Depending on the monitor models Color Control, Sharpness, Contrast,
Color Tone, Brightness will not be adjustable in MagicColor mode of Full and Intelligent.
MagicTune™ will be disappear if you excute MagicZone, and closing the
MagicZone after adjusting, will show the MagicTune™ again.
(System Tray is Unhecked)
MagicTune™ will be disappear if you excute MagicZone, and closing the
MagicZone after adjusting. will not show MagicTune™ again.
(System Tray is Checked)
MagicColor mode will be different according to monitor models.
MagicZone mode will show if the monitor supports the function.
Gamma correction changes the luminance of the colors with intermediate luminance.
Gamma
Gamma mode will be different according to monitor models. Some monitor will only support Three modes( Mode1, Mode2, Mode3).
Image Tab Definition
Adjusts the Fine , Coarse and Position values.
Image Setup z z z
Fine : Removes noise such as horizontal stripes.
If the noise persists even after Fine tuning, repeat it after adjusting the frequency
(clock speed).
Coarse : Removes noise such as vertical stripes.
Coarse adjustment may move the screen image area.
You may relocate it to the center using the Horizontal Control menu.
Auto Setup : Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically.
Position Adjusts the screen location horizontally and vertically.
Sharpness Changes the clearance of image.
Option Tab Definition
You can configure MagicTune™ using the following options.
Preferences
Source Select
Loads the Preferences Dialog Box. Preferences in use will have an "V" in the check box. To turn on or off any Preference, position the cursor over the box and click. z z
Enable task tray menu .
- To access the MagicTune™ menus, click the icon on the [task tray menu].
The menus are not displayed if the [Enable System Tray] is deselected in
[Options] ' [Basic Settings].
Select Language - The language chosen affects only the language of the OSD. z z
Analog
Digital
Support Tab Definition
Shows the Asset ID and the version number of the program, and allows you to use the Help feature.
Help
Asset ID
Version
Visit the MagicTune™ website or click to open the Help files (User Manual) if you need any help installing or running MagicTune™. The User Manual opens within a basic browser window. you can use the server to control the Client monitor.
(Server program should be installed to use this program as Client)
User Name
User ID
Server IP
Shows the user name that is registered in PC.
Shows the user ID that is register in PC.
Write down the server IP .
Department Write down the department.
Location Write down the location.
Displays the version of MagicTune™.
Overview | Installation | OSD Mode |
Color
Calibration
| Uninstall | Troubleshooting
Color Calibration
1. Color Calibration
Color Calibration guides you to get optimal color condition for your monitor.
Proceed following 5steps for getting optimal monitor color condition .
1. Control "Brightness control bar" for matching the brightness of control patch and the brightness of background pattern
2. When you detect specific color tone on "Control patch", move the control cursor toward to the direction of the color tone referring to "Color reference Circle".
=> Adjustment is finished properly, you won't detect any color tone on Control patch.
3. When you finish adjustment for step1,Click "Next" button .
4. Repeat 1), 2), 3) procedures for remaining step2 ~ step5.
5. You can easily view the calibration effect through clicking "Preview " button!
How multiple users can use adjusted color values
Definition
When monitor is used by multiple users, color values which are adjusted via Color calibration for each users can be saved and used. Up to 5 users can use the saved color values.
1. How to save adjusted color values:
Press Next to make it change into Apply and then you can save adjusted color values.
As many as 5 values can be saved.
2. How to apply the saved color values:
Press Multi User button on main screen to select and use one of the saved color values.
2. Preview
Press "Preview" button on the Color Calibration.
The above picture will be shown.
1. Press "View Calibrated" button to see the calibration effect which you adjusted.
2. Press "View Uncalibrated" button to see the original image.
Overview | Installation | OSD Mode |
Color
Calibration
| Uninstall | Troubleshooting
Uninstall
The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the
Windows™ Control Panel.
Perform the following steps remove MagicTune™.
1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on
Windows™ XP, go to [Control Panel] in the [Start] menu.
2. Click the "Add or Remove Programs" icon in Control Panel.
3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune™." Click on it to highlight it.
4. Click the "Change/Remove" button to remove the program.
5. Click "Yes" to begin the uninstall process.
6. Wait until the "Uninstall Complete" dialog box appears.
Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers) and software upgrades.
Overview | Installation | OSD Mode |
Color
Calibration
| Uninstall | Troubleshooting
Troubleshooting
The current computing system is not compatible with MagicTune™.
Please press OK and click on the "Shortcut to the MagicTune™ site" to view our home
page for further reference.
An error may occur when your video/graphic card is not in the 'Available' list.
(The latest or oldest video cards may not be compatible.)
Please visit our homepage to see the Troubleshooting section.
An error may occur if the card maker has modified the video card driver or the graphics chip even when the video card is in the list.
Please visit our homepage to see the Troubleshooting section.
Check if your monitor is manufactured by Samsung.
Products from other manufacturers may cause errors.
Only Samsung products are able to support this feature.
An error may occur even when your monitor is manufactured by Samsung but is out of date.
Check if your monitor is able to support MagicTune™.
This feature is only supported by those monitors that are registered on our homepage.
Check for the monitor before purchasing it as out-of-date models are not supported.
An error occurs when no information on EDID (Extended Display Identification
Data) exists for the current monitor.
This happens when from your desktop, Start > Setup > Control Panel > System >
Hardware > Device Manager > Monitor is selected, the current "Plug-and-play monitor" is removed and new hardware is searched for but the system couldn't find any "Plug-and-play monitor".
Please visit our homepage to see the Troubleshooting section.
An error occurs when replacing the monitor with a new one when the system power is off but the system has not been restarted.
Please restart the system each time the monitor is replaced before using
MagicTune™.
An error occurs when the video card driver is not installed properly.
This happens when the current video card list is not displayed normally. You can check this via Start > Setup > System > Hardware > Device Manager > Display
Adapter.
Visit the video card maker's homepage and download and install the latest driver.
For more information about the video card, contact the card manufacturer.
To ensure normal operation, please restart your system.
An error occurs when the system is not restarted after installing MagicTune™.
(This is for Win98SE and WinMe only.)
Restart the system before use.
For the best performance of MagicTune™, adjust to the optimal resolution. Refer to the
User Guide for the optimal resolution.
If you do not adjust to the optimal resolution and perform Color Calibration, the monitor cannot be adjusted to the optimal condition.
Refer to the manual for the optimal resolution.
This video card does not support MagicTune™.
Please install a new video card driver.
An error occurs when the video card driver is not installed properly.
This happens when the current video card list is not displayed normally. You can check this from Start > Setup > System > Hardware > Device Manager > Display
Adapter.
Visit the video card manufacturer's homepage and download and install the latest driver.
For more information about the video card, contact the card manufacturer.
As the Highlight program uses the communication lines,
please exit the Highlight program before you can access MagicTune™.
Some of Samsung CDT monitors support the Highlight feature.
When using both the Highlight feature and MagicTune™ simultaneously, conflicts occur, which cause errors.
Make sure to turn OFF Highlight before using MagicTune™.
Troubleshooting
z
MagicTune™ may not work in case monitor is replaced or driver of graphic card is updated while
MagicTune™ is operating. If so, please restart the system.
Symptom Check List Solutions
Check when
MagicTune™ does not function properly.
MagicTune™ feature is found only on PC (VGA) with Window OS that supports Plug and Play.
* To check whether your PC is available for
MagicTune™ feature, follow the
steps below (When Windows™ is XP);
Control Panel -> Performance and Maintenance
-> System -> Hardware -> Device Manager ->
Monitors -> After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware.
MagicTune™ is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with
MagicTune™ doesn't work properly.
Have you changed your PC or video graphic card?
the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/MagicTune
Download the latest program. The program can be downloaded http://www.samsung.com/monitor/MagicTune .
z z
Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers) and software upgrades.
Visit the MagicTune™ website and download the installation software for MagicTune™ MAC.
Check List
Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the
Information section or contact your dealer .
Symptom Check List Solutions
No images on the screen. I cannot turn on the monitor.
Is the power cord connected properly?
Check the power cord connection and supply.
Can you see "Check Signal
Cable" on the screen?
(Connected using the D-sub cable)
Check the signal cable connection.
(Connected using the DVI cable)
If you still see an (error) message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog.
Press button to have the monitor doublecheck the input signal source.
If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen.
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for
Windows ME/XP/2000) and then change the frequency of the video card.
(Refer to the Preset Timing Modes )
Note: If the initial screen (the login screen) does not appear, contact the Service Center or your dealer .
Can you see "Not Optimum
Mode","Recommended Mode
1680 x 1050 60 Hz" on the screen?
You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly.
Adjust the maximum resolution and frequency that the monitor can handle properly.
If the display exceeds SXGA or 75 Hz, a
"Not Optimum Mode","Recommended
Mode 1680 x 1050 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not
Optimum Mode","Recommended Mode
There is no image on the screen.
Is the power indicator on the monitor blinking at 1 second intervals?
Connected using the DVI cable?
1680 x 1050 60 Hz" message appears for one minute and then disappears.
Please change to the recommended mode during this one-minute period.
(The message is displayed again if the system is rebooted.)
The monitor is in PowerSaver mode. press a key on the keyboard to activate the monitor and restore the image on the screen.
If there is still no image, press the ' ' button.
Then press any key on the keyboard again to activate the monitor and restore the image on the screen.
You may get a blank screen if you boot the system before you connect the DVI cable, or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals.
Connect the DVI cable and then reboot the system.
I cannot see the On
Screen Display.
Have you locked the On Screen
Display (OSD) Menu to prevent changes?
Unlock the OSD by pressing the MENU button for at least 5 seconds.
The screen shows strange colors or just black and white.
Is the screen displaying only one color as if looking at the screen through a cellophane paper?
Check the signal cable connection.Make sure the video card is fully inserted in it's slot.
Have the screen colors become strange after running a program or due to a crash between applications?
Reboot the computer.
Has the video card been set properly?
Set the video card by referring to the video card manual.
The screen suddenly has become unbalanced.
The screen is out of focus or OSD cannot be adjusted.
LED is blinking but no images on the screen.
Have you changed the video card or the driver?
Have you adjusted the resolution or frequency to the monitor?
Adjust screen image position and size using the OSD.
Adjust the resolution and frequency at the video card.
(Refer to the Preset Timing Modes ).
The screen can be unbalanced due to the cycle of the video card signals.
Readjust Position by referring to the OSD.
Have you adjusted the resolution or frequency on the monitor?
Is the frequency properly adjusted when checking the
Display Timing on the menu?
Adjust the resolution and frequency of the video card.
(Refer to the Preset Timing Modes ).
Adjust the frequency properly by referring to the video card manual and the Preset
Timing Modes .
(The maximum frequency per resolution may differ from product to product.)
There are only 16 colors shown on the screen.
The screen colors have changed after changing the video card.
Have the Windows colors been set properly?
Has the video card been set properly?
Windows ME/2000/XP:
Set the colors properly at the Control Panel
→ Display → Settings.
Set the video card by referring to the video card manual.
There is a message that reads
"Unrecognized monitor, Plug &
Play (VESA DDC) monitor found".
Have you installed the monitor driver?
See the video card manual to see if the Plug & Play (VESA
DDC) function can be supported.
Check when
MagicTune™ does not function properly.
MagicTune™ feature is found only on PC (VGA) with Window
OS that supports Plug and
Play.
Install the monitor driver according to the
Driver Installation Instructions .
Install the monitor driver according to the
Driver Installation Instructions .
* To check whether your PC is available for
MagicTune™ feature, follow the
steps below (When Windows is XP);
Control Panel -> Performance and
Maintenance -> System -> Hardware ->
Device Manager -> Monitors -> After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new
Hardware.
MagicTune™ is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune
MagicTune™ doesn't work properly.
Have you changed your PC or video graphic card?
Download the latest program. The program can be downloaded. http://www.samsung.com/monitor/magictune
Visit the MagicTune™ website and download the installation software for MagicTune™
MAC.
Check the following items if there is trouble with the monitor.
1. Check if the power cord and the video cables are properly connected to the computer.
2. Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)
3. If you installed a new video card or if you assembled the PC, check if the installed the adapter
(video) driver and the monitor driver.
4. Check if the scanning ratio of the video screen is set at 56 Hz ~ 75 Hz.
(Do not exceed 60 Hz when using the maximum resolution.)
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel→System→Device Administrator" and then reboot the computer to reinstall the adapter (video) driver.
If problems repeatedly occur, contact an authorized service center .
Q & A
Question
How can I change the frequency?
Answer
Frequency can be changed by reconfiguring the video card.
Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.)
How can I adjust the resolution?
Windows ME/XP/2000 : Set the resolution at the Control Panel →
Display → Settings.
* Contact the video card manufacturer for details.
How can I set the Power Saving function?
Windows ME/XP/2000 : Set the function at BIOS-SETUP of the computer or the screen saver. (Refer to Windows/Computer
Manual).
How can I clean the outer case/LCD Panel?
Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water.
Do not leave any remains of the detergent nor scratch the case.
Do not allow any water to go inside the monitor.
Self-Test Feature Check
Self-Test Feature Check | Warning Messages | Environment | Useful Tips
Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.
Self-Test Feature Check
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
3. Turn on the monitor.
If the monitor is functioning properly, you will see a box in the illustration below.
This box appears during normal operation if the video cable becomes disconnected or damaged.
4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.
Warning Messages
If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable.
Environment
The location and the position of the monitor may influence the quality and other features of the monitor.
1. If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room.
2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor.
Useful Tips z
A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, z noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer.
Judging the monitor's working condition
If there is no image on the screen or a "Not Optimum Mode","Recommended Mode 1680 x
1050 60 Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on.
{
If there is a message coming up on the screen or if the screen goes white, this means the
{ monitor is in working condition.
In this case, check the computer for trouble.
General
General
Model Name
LCD Panel
Size
Display area
Pixel Pitch
Type
Synchronization
Horizontal
Vertical
Display Color
16.7 M Colors (8bit + RGB)
SyncMaster 205BW
20.1 " Diagonal (51 cm)
433.44 mm (H) x 270.9 mm (V)
0.258 mm (H) x 0.258 mm (V) a-si TFT active matrix
30 ~ 81 k Hz
56 ~ 75 Hz
Resolution
Optimum resolution
Maximum resolution
1680 x 1050@60 Hz
1680 x 1050@60 Hz
Input Signal, Terminated
RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB
0.7Vp-p Positive at 75Ω ±10%
Separate H/V sync, Composite sync, SOG, TTL level positive or negative.
Maximum Pixel Clock
156 MHz
Power Supply
AC 100 to 240 Vac(+/- 10%), 60/50Hz ± 3 Hz
Signal Cable
15pin to 15pin D-sub cable, Detachable, 1.8 m
DVI-D to DVI-D connector, Detachable, 2.0 m (option)
Power Consumption
Less than 55 W
Dimensions (WxDxH)/ Weight
471.4 x 200.0 x 351.8 mm / 18.5 x 7.9 x 13.9 inch (with Basic Stand) / 6.8 kg / 15 lbs
471.4 x 69.5 x 307.9 mm / 18.5 x 2.7 x 12.1 inch (without Basic Stand)
VESA Mounting Interface
75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating Temperature: 50 °F ~ 104 °F (10 °C ~ 40 °C)
Humidity: 10% ~ 80%, non-condensing
Storage Temperature: -4 °F ~113 °F (-20 °C ~ 45 °C)
Humidity: 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm
(one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. z
For example, the number of TFT LCD sub pixels that is contained in this product are 5,292,000.
Note: Design and specifications are subject to change without prior notice.
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature.
State
Normal
Operation
Power saving mode
Power off
EPA/ENERGY
2000
(Power button)
Power off
(Power Switch)
Power Indicator Blue Blue, Blinking Black Black
Power
Consumption
Less than 55 W
Less than 2 W
(Off-mode)
Less than 1 W
(120 Vac / 220 Vac)
0 W
This monitor is EPA ENERGY STAR functionality.
®
compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS
As an ENERGY STAR
®
Partner, SAMSUNG has determined that this product meets the ENERGY STAR
®
guidelines for energy efficiency.
IBM, 640 x 350
IBM, 640 x 480
IBM, 720 x 400
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1680 x 1050
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing Modes
Display Mode
Horizontal
Frequency
(kHz)
31.469
31.469
31.469
Vertical
Frequency
(Hz)
70.086
59.940
70.087
Pixel Clock
(MHz)
25.175
25.175
28.322
Sync Polarity
(H/V)
+/-
-/-
-/+
35.000
49.726
66.667
74.551
30.240
57.284
-/-
-/-
68.681 75.062 100.00 -/-
37.500 75.000 31.500 -/-
37.861 72.809 31.500 -/-
35.156 56.250 36.000 -/-
37.879 60.317 40.000 +/+
46.875 75.000 49.500 +/+
48.077 72.188 50.000 +/+
48.363 60.004 65.000 -/-
56.476 70.069 75.000 -/-
60.023 75.029 78.750 +/+
67.500 75.000 108.00 +/+
60.000 60.000 108.00 +/+
79.976 75.025 135.00 +/+
65.290
59.954
Horizontal Frequency
146.25
-/-
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh
Rate. Unit: Hz
Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please
contact the SAMSUNG customer care center.
North America
CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca
MEXICO
U.S.A
01-800-SAMSUNG (7267864)
1-800-SAMSUNG (7267864) http://www.samsung.com/mx http://www.samsung.com
ARGENTINE
BRAZIL
CHILE
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
Latin America
0800-333-3733
0800-124-421
800-726-7864 (SAMSUNG)
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-7267-864
1-800-100-5303 http://www.samsung.com/ar http://www.samsung.com/br http://www.samsung.com/cl http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin
Europe
BELGIUM 02 201 2418 http://www.samsung.com/be
RUSSIA
UKRAINE
AUSTRALIA
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
VIETNAM
SOUTH AFRICA
U.A.E
CZECH REPUBLIC
DENMARK
FINLAND
FRANCE
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
844 000 844
38 322 887
09 693 79 554
08 25 08 65 65 (€ 0,15/min)
01805 - 121213 (€ 0,12/Min)
06 40 985 985
199 153 153
02 261 03 710
0900 20 200 88 (€ 0.10/Min)
231 627 22
0 801 801 881
80 8 200 128
0850 123 989
902 10 11 30
08 585 367 87
0870 242 0303
8-800-200-0400
8-800-502-0000
CIS http://www.samsung.com/cz http://www.samsung.com/dk http://www.samsung.com/fi http://www.samsung.com/fr http://www.samsung.de
http://www.samsung.com/hu http://www.samsung.com/it http://www.samsung.lu
http://www.samsung.com/nl http://www.samsung.com/no http://www.samsung.com/pl http://www.samsung.com/pt http://www.samsung.com/sk http://www.samsung.com/es http://www.samsung.com/se http://www.samsung.com/uk http://www.samsung.ru
http://www.samsung.com/ur
1300 362 603
Asia Pacific
800-810-5858, 010- 6475 1880
2862 6001
3030 8282, 1600 1100 11
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG (7267864)
1800-SAMSUNG (7267864)
1800-29-3232, 02-689-3232
0800-329-999
1 800 588 889 http://www.samsung.com/au http://www.samsung.com.cn
http://www.samsung.com/hk http://www.samsung.com/in http://www.samsung.com/id http://www.samsung.com/jp http://www.samsung.com/my http://www.samsung.com/ph http://www.samsung.com/sg http://www.samsung.com/th http://www.samsung.com/tw http://www.samsung.com/vn
Middle East & Africa
0860 7267864 (SAMSUNG)
800SAMSUNG (7267864) http://www.samsung.com/za http://www.samsung.com/mea
Terms
Dot Pitch
The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot
Pitch'. Unit: mm
Vertical Frequency
The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or
Refresh Rate. Unit: Hz
Example :If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal
Frequency. Unit: kHz
Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the top to the bottom in order is called the
Non-Interlace method while showing odd lines and then even lines in turn is called the
Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose the screen image is called
'resolution'. This number shows the accuracy of the display. High resolution is good for performing multiple tasks as more image information can be shown on the screen.
Example : If the resolution is 1680 x 1050 , this means the screen is composed of 1680 horizontal dots (horizontal resolution) and 1050 vertical lines (vertical resolution).
For Better Display
1. Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD.
{
{
Resolution: 1680 x 1050
Vertical frequency (refresh rate): 60 Hz
2. TFT LCD panel manufactured by using advanced semiconductor technology with precision of
1ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen.
This is not from bad quality and you can use it without uneasiness.
{ For example, the number of TFT LCD sub pixels that is contained in this product are
5,292,000.
3. When you clean the monitor and the panel outside, please apply the recommended small amount of cleaner by using soft and dry cloth and polish it. Let LCD area not to be forced but to be scrubbed out softly.
If excessive force is applied, you can have a stain on it.
4. If you are not satisfied with the quality of picture, you can get better quality of picture by executing "auto adjustment function" in display screen that is appeared as window termination button is pressed.
If there's still noise after automatic adjustment, use FINE/COARSE adjustment function.
5. If you view a fixed screen for an extended period of time, residual image or blurriness may appear.
Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time.
Authority
Information in this document is subject to change without notice.
© 2006 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics
Co., Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and
Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR® name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an
ENERGY STAR® Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.
Class B
This device is a Class B digital apparatus. For Safety and EMC compliance guide, you may refer to
"Regulatory" Guide.
MÉXICO
IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V.
Vía Lopez Portillo No. 6, Col. San Fco. Chilpan
Tultitlán, Estado de México, C.P. 54940
Tel: 01-55-5747-5100 / 01-800-726-7864
EXPORTADO POR: Samsung Electronics CO.,LTD.
416, Mae tan-3dong, Yeongtong - gu,
Suwon City, Gyeonggi-do Korea
PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time.
This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention.
Warranty
Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.
What is Image retention ?
During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including
LCD,are subject to image retention. This is not a product defect.
Please follow the suggestions below to protect your LCD from image retention
Power Off, Screen Saver, or Power Save Mode
Ex) z
Turn the power off when using a stationary pattern.
- Turn the power off for 4 hours after 24 hours in use
- Turn the power off for 2 hours after 12 hours in use z z
Use a Screen saver if possible
- Screen saver in one color or a moving image is recommended.
Set the Monitor to power off with the PC Display Properties Power Scheme.
Suggestions for specific applications
Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems
We recommend that you follow set up of your display system program as below:
Display Information together with Logo or Moving image cycle.
Ex) Cycle : Display Information for 1 hour followed by a
Display Logo or moving image for 1 minute.
Change the Color Information periodically (Use 2 different colors).
Ex) Rotate the Color Information with 2 colors every 30 minutes.
Avoid using a combination of characters and background color with large difference in luminance.
Avoid using Grey colors, which can cause Image retention easily. z
Avoid: Colors with big difference in luminance (Black & White, Grey)
Ex) z
Recommended settings: Bright colors with little difference in luminance
- Change the characters color and background color every 30 minutes
Ex)
- Every 30 minutes, change the characters with movement.
Ex)
The best way to protect your monitor from Image retention is to set your PC or
System to operate a Screen Saver program when you are not using it.
Image retention may not occur when a LCD panel is operated under normal conditions.
Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The voltage difference between electrodes increases with time, forcing the liquid crystal to lean. When this occurs, the previous image may be seen when the pattern is changed.
To prevent this, the accumulated voltage difference must be decreased.
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- 50.8 cm (20")
- 1680 x 1050 pixels
- 6 ms 300 cd/m² 700:1
- 75 W
Related manuals
advertisement
Table of contents
- 1 SyncMaster 205BW
- 2 Safty Instructions
- 2 Notational
- 3 Power
- 4 Installation
- 5 Clean
- 6 Others
- 10 Introduction
- 10 Unpacking
- 11 Front
- 12 Rear
- 13 Setup
- 13 Connecting the Monitor
- 14 Using the Stand
- 15 Installing the Monitor Driver(Automatic)
- 16 Installing the Monitor Dtiver(Manual)
- 20 Natual Color
- 21 Adjusting Your Monitor
- 21 User Control Buttons
- 21 Direct Functions
- 25 OSD Functions
- 31 MagicTune™
- 46 Troubleshooting
- 46 Check List
- 48 Q & A
- 49 Self-Test Feature Check
- 51 Specifications
- 51 General
- 52 PowerSaver
- 53 Preset Timing Modes
- 54 Information
- 54 Contact SAMSUNG WORLD-WIDE
- 56 Terms
- 56 For Better Display
- 57 Authority
- 58 Image Retention Free
- 60 Correct Disposal