Samsung SVMi-8 Answering Machine Owner's Manual

»
CD-DJ1
PORTABLE DJ CD/MP3 PLAYER
OWNER'S MANUAL
D00890300A
IMPORTANT SAFETY PRECAUTIONS
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
This appliance has a serial number located on the rear panel.
Please record the model number
and se rial numbe r a nd retain
them for your records.
Model number
Serial number
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
For U.S.A.
TO THE USER
CAUTION
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
h a r m f u l i n t e r f e re n c e i n a re s i d e n t i a l
installation. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instruction manual,
may cause harmful interference to radio
communications.
Changes or modifications to this equipment
not expressly approved by TEAC
CORPORATION for compliance could
void the user's authority to operate this
equipment.
H o w e v e r, t h e re i s n o g u a r a n t e e t h a t
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the following
measures.
a) Reorient or relocate the receiving
antenna.
b) Increase the separation between the
equipment and receiver.
c) Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
d) Consult the dealer or an experienced
radio/TV technician for help.
TASCAM CD-DJ1
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
6 Clean only with dry cloth.
14 Refer all ser vicing to qualified ser vice
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been
dropped.
7 Do not block any ventilation openings.
Install in accordance with the manufacturer's instructions.
• Do not expose this apparatus to drips or
splashes.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
8 Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has
two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an
electrician for replacement of the obsolete
outlet.
10 Protect the power cord from being walked
on or pinched particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
• Do not place any objects filled with liquids,
such as vases, on the apparatus.
• Do not install this apparatus in a confined
space such as a bookcase or similar unit.
• The apparatus draws nominal non-operating power from the AC outlet with its
POWER switch in the off position.
• The apparatus should be located close
enough to the AC outlet so that you can
easily grasp the power cord plug at any
time.
• An apparatus with Class I construction
shall be connected to an AC outlet with a
protective grounding connection.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is
used, use caution when moving the cart/
apparatus combination to avoid injury from
tip-over.
13 Unplug this apparatus during lightning
storms or when unused for long periods of
time.
TASCAM CD-DJ1
IMPORTANT SAFETY INSTRUCTIONS
This product has been designed and manufactured according to FDA regulations "title 21,
CFR, chapter 1, subchapter J, based on the
Radiation Control for Health and Safety Act of
1968", and is classified as a class 1 laser product. There is no hazardous invisible laser radiation during operation because invisible laser
radiation emitted inside of this product is completely confined in the protective housings.
CAUTION
The label required in this regulation is shown at
1.
• IF THIS PRODUCT DEVELOPS TROUBLE,
C O N TACT YO U R N E A R EST Q UA L I FI ED
SERVICE PERSONNEL, AND DO NOT USE
THE PRODUCT IN ITS DAMAGED STATE.
DTA
Optical pickup:
Type:
KSM-900AAA
Manufacturer: SONY Corporation
Laser output:
Less than 1 mW play on
the objective lens
Wavelength:
775 to 816 nm
TASCAM CD-DJ1
• D O N O T R E M O V E T H E P R O T E C T I V E
HOUSING USING A SCREWDRIVER.
• USE OF CONTROLS OR ADJUSTMENTS
O R PE R FO R M A N C E O F PR O C E D U R ES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
Contents
1- Introduction............................. 6
Supplied accessories....................... 6
Precautions and notes for
placement and use....................... 7
Beware of condensation....................7
Power supply......................................7
Sleep function.....................................7
Handling of compact discs.................8
About this manual.......................... 8
Setting the IN point.........................17
Setting the OUT point......................17
Canceling loop playback..................17
Re-loop playback.......................... 18
Canceling loop points......................18
Changing the OUT point..................18
HALF..................................................... 18
SET........................................................ 18
Adjusting the OUT point..................18
Restoring the OUT point..................18
2- Features of the CD-DJ1............ 9
Tempo control............................... 18
Top panel........................................ 9
Front panel.....................................11
Rear panel......................................11
Display............................................11
Key Original function................... 19
Pitch bend function...................... 19
The “home” screen...........................11
Setup screen.....................................12
3- Setup menu............................ 13
Setup menu operation..................13
Menu configuration......................13
4- Playback operations.............. 14
Discs for playback......................... 14
Playback modes............................ 14
Basic operation............................. 14
Track selection.............................. 14
Track search...................................15
Auto Cue........................................15
Auto Ready....................................15
CD text data display......................15
Setting the tempo range.................18
When set to SRCH................................ 19
When set to BEND............................... 19
6- MP3 playback......................... 20
Playback range selection.............. 20
Folder selection................................... 20
Display indication......................... 20
Functions disabled during MP3
playback...................................... 20
MP3 file folders and tracks.......... 21
7- Other features........................ 22
TT-M1 use...................................... 22
Turning the TT-M1 on and off........ 22
TT-M1 Calibration............................ 22
Setting the cue point.......................16
Functions disabled during TT-M1
use............................................... 22
Resetting the unit......................... 22
Setting output volume................. 23
Auto Play....................................... 23
Adjusting the backlight................ 23
Adjusting the contrast................. 23
Play mode............................................. 16
Cue mode............................................. 16
8- Specifications......................... 24
5- DJ functions............................ 16
Cue................................................. 16
Using and confirming the cue
point................................................16
Hot Cue......................................... 16
Setting Hot Cue points....................16
Canceling Hot Cue points................17
Using and confirming Hot Cue
points..............................................17
Flash Start.........................................17
Specifications................................ 24
Audio performance...................... 24
Backup memory............................ 25
Setup menu settings (all except for the
system reset parameter).................. 25
Other settings...................................... 25
Dimensional drawing................... 25
Loop playback................................17
TASCAM CD-DJ1
1- Introduction
Thank you for purchasing the TASCAM CD-DJ1. This
DJ-use CD player is portable, compact and user-friendly.
Please study this manual thoroughly before using
the player to ensure that you understand how to use
it properly. We hope that with this knowledge you
will enjoy using the CD-DJ1 and all of its features for
many years. After you have finished reading this manual, please keep it in a safe place for future reference.
• The Key Original function makes it possible to
maintain the same pitch while changing the playback
tempo.
• CD playback can be controlled with an analog
turntable by attaching a TASCAM TT-M1 (sold
separately) to the CD-DJ1.
• The 4 playback modes include all tracks, singletrack, all track repeat and single-track repeat.
• Seamless loop playback between any two points is
Main Features of the CD-DJ1
• The CD-DJ1 is compact, lightweight and highly
portable, making it easy to set up in DJ booths and
other tight spaces.
• The CD-DJ1 can play audio CD-Rs and CD-RWs
as well as commercially available audio CDs. In
addition, the CD-DJ1 can play MP3 files.
• Anti-shock memory that is effective for at least 7
seconds allows the CD-DJ1 to output sound continuously even in clubs and other environments
with heavy vibrations.
• The CD-DJ1 has a large easy-to-push PLAY/
PAUSE key as well as separate SEARCH and
SKIP keys.
• The CD-DJ1 has multiple cueing functions,
including 2 HOT CUE keys and a regular CUE
key.
possible.
• For MP3 files, either all tracks in a single folder or
all tracks in all folders can be selected for play.
• The CD-DJ1 has Auto Cue and Auto Ready functions.
• The Auto Play function allows automatic playback
after the power is turned on.
• The display not only shows the status of the
CD-DJ1 and the loaded disc, but can also show
CD text data and MP3 file titles.
• The backlight brightness and display contrast can
be adjusted.
• The Setup menu allows a variety of functions to
be customized.
• The Sleep function automatically stops the CD
mechanism and turns off the backlight if the unit
is unused for 30 minutes.
• Instant play capability allows immediate playback
start from a paused state.
• The CD-DJ1 has the 60-mm tempo slider with
adjustable tempo range.
• The JOG dial can be used for pitch bend, frame
search, and menu operation.
Supplied accessories
In addition to this manual, this product includes the
following items:
•CD-DJ1 unit.......................................................... 1
•AC adapter (PS-PS5)............................................ 1
Please use caution when removing the main unit
from the package to avoid damage or injury. Please
keep the box and packaging materials for future
transportation.
TASCAM CD-DJ1
If any of the accessory items are missing, please contact your TASCAM supplier.
1- Introduction
Precautions and notes for placement and use
Please use the CD-DJ1 only within its operating temperature range of 5°C to 35°C (41°F to 95°F). Please
avoid use or storage in dusty or humid environments
because these conditions can cause malfunction.
To maintain top performance, and prolong operating
life, observe the following notes, precautions and
environmental conditions:
• Avoid exposing it to extremes of temperature and
humidity and avoid mechanical shocks.
• Keep the unit away from strong magnetic fields
(TV sets, computer monitors, large electric
motors, etc.).
• Avoid placing this unit on top of any heat-generating electrical device such as a power amplifier.
• Always use the supplied AC adapter (PS-PS5)
with the standard home electrical power outlet. Use of other AC adapters may damage the
CD-DJ1.
• Use the unit on a table or rack that is level and
sturdy.
• Wipe dirt from the unit with a dry cloth. Never
use thinner, benzene or other solvents because
they may cause acrylic parts and coated surfaces
to dissolve, labels to be eroded or other damage.
• Relative humidity should be 30 to 90 percent.
• As the unit may become hot during operation,
always leave sufficient space above the unit for
ventilation. Do not operate this unit in a confined
space such as a bookcase, and do not put anything
on top of the unit.
Beware of condensation
If the unit (or a compact disc) is moved from a cold
to a warm place, or used after a sudden temperature
change, there is a danger of condensation; vapor in
the air could condense on the internal mechanism,
making correct operation impossible.
Power supply
Attach the DC plug of the supplied AC adapter to the
DC IN jack on the rear panel and connect the power
plug to a standard electrical power outlet.
Pressing the POWER switch on the rear panel lights
up the display. After a brief start-up screen, the home
screen will appear.
Sleep function
If playback is paused and the unit has not been used
for 30 minutes, the unit will automatically go to
sleep, stopping the CD mechanism and turning off
the backlight.
TASCAM CD-DJ1
1- Introduction
Handling of compact discs
The CD-DJ1 has been designed for the playback of
CD-DA (standard audio) format discs and MP3 files
recorded on the discs using the ISO9660 format: In
addition to ordinary 12cm (5-inch) and 8cm (3-inch)
CDs, it can also play properly recorded CD-Rs and
CD-RWs.
• Keep discs away from direct sunlight, and places
• Always place the compact discs in the trays with
• Do not insert discs that have adhesive remaining
their label facing upward.
• To remove a disc from its case, press down on the
center of the disc holder, then lift the disc out,
holding it carefully by the edges.
of high heat and humidity. If left in such places,
warping could result.
• Do not affix any labels or stickers to the label side
of the disc. Do not write on the disc with a ballpoint pen.
from tape or stickers that have been removed. If
they are inserted into the player, they could stick
to the internal mechanism, requiring removal by a
technician.
• Do not use cracked discs.
• Only use circular compact discs. Avoid using noncircular promotional, etc. discs.
• Avoid getting fingerprints on the signal side (the
non- label side). Grime and dust may cause skipping, so keep discs clean and store them in their
cases when not being played. To clean the signal
side of a disc, wipe gently with a soft dry cloth
from the center towards the outside edge.
• Do not use any record spray, anti-static solutions,
benzene, paint thinner or other chemical agents to
clean CDs as they could damage the delicate playing
surface. It may cause CDs to become unplayable.
• The CD-DJ1 cannot play unfinalized CD-R/RWs.
• The unit may not be able to play some CD-Rs and
CD-RWs due to disc quality or recording conditions.
• Music discs with copy control, a copy-protection
system, have been released form several record
companies in an attempt to protect the copyright.
Since some of these discs do not comply with the
CD specifications, they may not be playable on
the CD-DJ1.
• Discs should be returned to their cases after use to
avoid serious scratches that could cause the laser
pickup to “skip.”
About this manual
In this manual, we use the following conventions:
• The names of keys and controls are given in the
following typeface: TEMPO.
• When the alphanumeric portion of the display
shows a message, this is shown in the following
typeface:
.
TASCAM CD-DJ1
• If a preset indicator in the display (i.e. one which
cannot change, but is either on or off) is shown,
this is shown as follows: REMAIN.
IMPORTANT
2- Features
SAFETY INSTRUCTIONS
of the CD-DJ1
Top panel
1
2
3
4
5
6
7
8
9
0
q
w
e
r
1
CD cover To open the CD cover, lift the cover
from the indentations on the sides of the unit.
When a disc is loaded and the CD cover is closed,
the CD-DJ1 will read the disc information (TOC).
After reading is complete, the unit will pause.
When using the Setup menu, this key becomes the
ENTER key.
2Lock lever When the CD cover is closed, pulling
this lever down shows the LOCK label, indicating
that the CD cover cannot be opened.
4
PLAY MODE and SHIFT key Pressing this key
cycles through the playback modes in the following order: Continuous playback of all tracks
(default setting) œ Single-track playback œ
Repeat playback (all tracks) œ Single-track repeat
playback.
Pushing the lever up shows the UNLOCK label,
indicating that the CD cover can be opened.
CAUTION
Please set the lever to LOCK when moving the
unit to prevent the disc from falling out.
3TIME/ENTER and TITLE key When the home
screen is displayed, pressing this key cycles
through the playback time display modes in the
following order: ELAPSED (track time elapsed) œ
REMAIN (track time remaining) œ TOTAL REMAIN
(disc time remaining).
NOTE
ELAPSED (track time elapsed) is the only
usable time display mode for MP3 playback.
REMAIN and TOTAL REMAIN modes cannot be
used.
Pressing this key while holding down the SHIFT
key will cycle through CD text data or MP3 file
title information.
This key acts as the SHIFT key when held down
with other keys. When used this way, the playback
mode will not be changed.
5SKIP (µ/≤) keys These allow track selection
both during playback and while the CD is paused.
For more information, please see “Track selection” on page 14.
During MP3 file playback, pressing this key while
holding down the SHIFT key will select folders
(see “Folder selection” on page 20).
6SEARCH (∆/˚) keys Search tracks, or pitch
bend a track when set to BEND using SRCH KEY
setting in the Setup menu (see “Setup menu” on
page 13).
TASCAM CD-DJ1
IMPORTANT
2Features of
SAFETY
the CD-DJ1
PRECAUTIONS
When set to SRCH, pressing these keys searches
through the tracks backward and forward in both
playback and pause mode (see “Track search” on
page 15).
When set to BEND, these keys cause pith bend.
During playback, holding down a SEARCH key
changes the tempo. When the keys are released,
the tempo will return to its original state (see
“Pitch bend function” on page 19).
By holding down the SHIFT key, pitch bend will
occur regardless of the SRCH KEY setting.
7 CUE key When a cue point is set, pressing this
key pauses the CD playback at the cue point (Cue
Pause). During cue pause, holding down the CUE
key for temporary playback. When the key is
released, the CD will pause again at the cue point
(Cue Pause).
If the PLAY/PAUSE key is pressed while the CUE
key is pressed, normal playback mode will resume
(see “Cue” on page 16).
The CUE key is also used to save cue points.
If the CUE key is pressed while the SHIFT key is
held down, the CUE mode will be changed (see
“Cue” on page 16).
8 ¥/π (PLAY/PAUSE) key When the unit is
paused, pressing this key starts playback. If
pressed during playback, the unit will pause.
This key lights during playback, and blinks while
paused.
If this key is pressed while the SHIFT key is held
down, TT-M1 calibration will start (see “TT-M1
Calibration” on page 22).
9 HOT CUE (1, 2) / CLEAR keys If a Hot Cue point
has not been set for a HOT CUE key, pressing this
key sets its Hot Cue point at the current playback
position (see “Setting Hot Cue points” on page 16).
If a Hot Cue point has been set and the Flash Start
is on, pressing the associated HOT CUE key will
restart playback from that point. When the Flash
Start is off, the unit pauses at the Hot Cue point
(see “Hot Cue” on page 16).
NOTE
Pressing the HOT CUE key while holding down the
SHIFT key will clear the Hot Cue point currently set.
10 TASCAM CD-DJ1
0 JOG dial When SRCH is selected using the
SRCHKEY setting in the Setup menu (see “Setup
menu” on page 13), turning this dial causes pith
bend that temporarily changes the playback
tempo. Playback will return to the original tempo
when the JOG dial is no longer turned (see “Pitch
bend function” on page 19).
When BEND is selected using SRCHKEY setting
in the Setup menu (see “Setup menu” on page 13),
turning this dial searches the tracks during playback.
When playback is paused, use this dial for scrub
playback.
Use this dial to select menu items and values in
the Setup menu.
q
RE-LOOP/EXIT key This key turns loop playback
on and off (see “Loop playback” on page 17).
If the RE-LOOP/EXIT key is pressed while the
SHIFT key is held down, any set loop playback
starting (IN) and stopping (OUT) points will be
cleared.
w
IN and OUT keys These keys are used to set the
loop playback starting (IN) point and stopping
(OUT) point. Pressing the OUT key during loop
playback changes the OUT point. In addition, during loop playback, pressing the OUT key while
holding down the SHIFT key allows the JOG dial
to be used to change the OUT point (see “Loop
playback” on page 17 and “Re-loop playback” on
page 18).
e
Tempo slider The slider adjusts playback tempo.
Pushing it in the “–” direction slows the tempo
while pulling it in the “+” direction accelerates it.
The amount of adjustment possible depends on the
Tempo Range setting.
NOTE
During TT-M1 use, the tempo slider cannot be
used.
r
TEMPO/KEY ORIG key This key sets the tempo
range. Pressing this key will cycle through the following tempo ranges: ±8% (default setting) œ
±16% œ ±32% œ ±100%.
The value flashes for a few seconds, and it will
light up when entered.
Pressing this key while the SHIFT key is held
down switches the Key Original on or off.
NOTE
During the TT-M1 use, this key cannot be used.
IMPORTANT
2- Features
SAFETY INSTRUCTIONS
of the CD-DJ1
Front panel
1 PHONES volume dial This dial adjusts the head-
phone output volume.
2 PHONES OUT jack This is a 1/4” (6.3 mm) stereo
headphone jack.
3 SETUP key Enter Setup menu mode by pressing
this key (see “Setup menu” on page 13).
1 2 3
Rear panel
1 Power switch This turns the CD-DJ1 power on
and off.
2 DC IN 9V jack Connect the supplied AC adapter
here.
3 TT-M1 jack Connects a separately sold TASCAM
TT-M1 scratch controller (see “TT-M1 use” on
page 22).
4 OUTPUT L/R jack (RCA pin jacks) These jacks
1 2
3
output the playback sound, and have a nominal
output level of –10 dBV.
4
Display features
The display shows the status of the CD-DJ1 and
information about the loaded disc. Normally, the
display shows the current settings and conditions, but
when the SETUP key is pressed, the Setup menu is
shown.
The backlight brightness and display contrast can be
adjusted using the Setup menu (see “Adjusting the
backlight” and “Adjusting the contrast” on page 23).
The “home” screen
5
1 23 4
6
1 Track number This shows the number of the cur-
rently selected track.
2 Total number of tracks During audio CD play-
back, the total number of tracks on the disc will
be shown.
During MP3 playback, depending on the Setup
menu FOLDER setting, the number of tracks in
the current folder or the total number of tracks on
the disc will be shown.
78 9
0
q
w
TASCAM CD-DJ1
11
IMPORTANT
2Features of
SAFETY
the CD-DJ1
PRECAUTIONS
3 Playback time The time value shown depends
on the currently selected playback time display
mode.
will be displayed when there is
no disc in the unit.
4 Playback time display mode The selected play-
back time display mode (ELAPSED, REMAIN, or TOTAL
REMAIN) is shown.
When the playback time display mode is set to
ELAPSED, the position indicator fills up from the
left.
When the playback time display mode is set to
REMAIN or TOTAL REMAIN, the position indicator
becomes shorter, with the segments disappearing
from the left.
When the Key Original function is on, K.ORIG
appears in place of the TEMPO indicator.
When the remaining playback time for the current
track is less than 30 seconds, the position indicator will flash slowly. When the remaining playback time is less than 10 seconds, the indicator
will flash rapidly.
When the TT-M1 switch is turned on, the TT-M
indicator is shown instead of the tempo value.
The position indicator is not be shown during
MP3 playback or when no disc is loaded.
6 MP3
9 Auto Cue A.CUE indicator appears when the Auto
5 Tempo display The TEMPO indicator and the cur-
rent tempo value are displayed.
will be displayed during MP3 play-
back.
Cue function is on.
7 Playback/repeat mode Displays the current
playback and repeat mode.
Auto Ready function is on.
• Continuous playback of all tracks: (no indication)
• Single-track playback: SINGLE
• All track repeat playback: ALL REPEAT
• Single-track repeat playback: SGL.REPEAT
8 Track title or playback position Displays CD
text data, MP3 file titles and other information
about the currently playing track. Nothing will be
displayed for audio CDs without text data.
Playback position During audio CD playback,
the current track playback position will be shown
with a 24-segment position indicator.
Playback position
Setup screen
The setup screen is shown on the display during
Setup menu mode. For further details, please see
“Setup menu” on page 13.
12 TASCAM CD-DJ1
0 Auto Ready A.RDY indicator appears when the
q Flash Start FLS indicator appears when the Flash
Start function is on.
w Current track length The length of the currently
playing track is displayed as
(minutes
and seconds) during audio CD playback.
IMPORTANT SAFETY 3INSTRUCTIONS
Setup menu
Setup menu operation
Various settings can be made using the CD-DJ1
Setup menu. These settings remain even when the
power is turned off.
1. Push the SETUP key on the front panel. The
Setup menu screen appears. The cursor points
to the currently selected menu item.
Cursor
Current
value
Menu item
3. Change the value using the JOG dial.
4. Press the ENTER key to set the value. The
highlighting will disappear, and other items
in the Setup menu can be selected with the
JOG dial.
5. Repeat steps 2 through 4 to set other menu
items.
6. When setting menu items is complete, press
the SETUP key to exit the Setup menu.
2. Select a menu item using the JOG dial and
push the ENTER key. The current value will
be highlighted in reverse contrast.
Menu configuration
The Setup menu allows adjustment of the following parameters.
Menu item
Displayed
Key Original
KEY ORIG
Turns Key Original function on and off Key Original function (page 19)
Digital Attenuation D. ATT
Sets output volume
Setting output volume (page 23)
TT-M1 Calibration
TTM CAL
Calibrates TT-M1
TT-M1 Calibration (page 22)
Auto Cue
AUTO CUE
Turns Auto Cue on and off
Auto Cue (page 15)
Auto Ready
AUTO RDY
Turns Auto Ready on and off
Auto Ready (page 15)
CD-ROM Folder play FOLDER
Selects disc playback range Playback range selection (page 20)
Flash Start
FLASH
Turns Flash Start on and off
Flash Start (page 17)
Auto Play AUTOPLAY
Turns automatic playback at startup
on and off
Auto Play (page 23)
CUE Key mode
CUE KEY
Selects CUE key operation mode Cue (page 16)
Loop OUT Key mode
OUT KEY
Selects OUT key operation mode Loop playback (page 17)
SEARCH Key function
SRCH KEY
Selects SEARCH key function
Track search (page 15)
LCD Contrast
LCD CONT
Adjusts LCD contrast
Adjusting the contrast (page 23)
Backlight Dimmer
DIMMER
Adjusts display backlight brightness Adjusting the backlight (page 23)
Resets CD-DJ1 settings and data
to original factory values
Resetting the unit (page 22)
System Reset RESET
FunctionManual section
TASCAM CD-DJ1
13
4- Playback operations
This chapter explains basic CD player functions.
Unless specifically noted, these instructions are for
using audio CDs.
For playback of CDs with MP3 files, see “MP3 playback” on page 20.
Discs for playback
The CD-DJ1 can play these types of discs.
• Commercial audio CDs and CD-DA format
CD-Rs and CD-RWs.
• CD-Rs and CD-RWs discs with MP3 files record-
However, the CD-DJ1 may not be able to play some
CD-Rs and CD-RWs due to disc quality or recording conditions. If the
error message
appears, remove and clean or replace the loaded disc.
ed in CD-ROM format (see “MP3 playback” on
page 20).
Playback modes
• Single-track playback: SINGLE
• All track repeat playback: ALL REPEAT
• Single-track repeat playback: SGL.REPEAT
This unit has four playback modes. The display
shows the currently selected mode. Press the PLAY
MODE key to change the playback mode.
• Continuous playback of all tracks: (no indication)
Basic operation
The following procedures explain use with the factory settings (playback mode is set to continuous
playback of all tracks and Auto Cue is on).
WARNING
When using headphones, be careful not to turn up
the volume too much. Listening at a high volume
over a long time can damage hearing.
1. Turn the power on by pushing the power
switch.
appears on the display.
2. Open the CD cover and place a disc label-side up.
3. Close the CD cover. The total number of
tracks and the total playback time appears on
the display.
5. Press the PLAY/PAUSE key. Playback begins
from track 1.
To Pause playback, press the PLAY/PAUSE
key. Press the PLAY/PAUSE key again to restart playback.
Use the SKIP keys to select specific tracks for
playback.
To monitor the sound with headphones, plug
the headphone cord into the PHONES OUT
jack and adjust the level with the PHONES
volume dial.
NOTE
The CD-DJ1 does not have a STOP key.
4. To prevent accidental CD cover opening, pull
down the lock lever until the word LOCK appears.
Track selection
Use the SKIP (µ/≤) keys to select tracks.
Press the µ SKIP key once when the CD is playing
or paused to jump to the start of the currently selected track. Press the µ SKIP key again to jump to the
start of the previous track.
14 TASCAM CD-DJ1
Pressing a SKIP key during playback starts playing
the newly selected track immediately.
Pressing a SKIP key when the CD is paused sets the
pause position to the start of the selected track (if
Auto Cue is on, the pause position is set to the first
moment of sound on the selected track).
4- Playback operations
When used with MP3 file discs, depending on the
Setup menu FOLDER setting, the SKIP keys cycle
through either all the tracks on the disc or only the
tracks in the currently selected folder. Regardless of
the FOLDER setting, however, pressing a SKIP (µ/
≤) key while holding down the SHIFT key skips
between folders.
Track search
Depending on the Setup menu SRCH KEY setting,
use either the JOG dial or the SEARCH (∆/˚)
keys to search tracks.
When the SRCH KEY setting is SRCH, hold down a
SEARCH (∆ or ˚) key while the CD is playing
or paused to search through the track. The ˚key
searches forward and the ∆ key searches backward.
When the SRCH KEY setting is BEND, turn the JOG
dial during playback to search the track. Turn clockwise to search forward and counterclockwise to
search backward.
Turning the JOG dial while the CD is paused allows
scrub playback.
Auto Cue
If the Auto Cue function is on when a track is selected, the pause position will be set at the first moment
of sound rather than the start of the track. This
allows the music on the selected track to be heard
immediately when the PLAY/PAUSE key is pressed if
there is silence at the start of the track.
Turn this function on and off using the Setup menu
AUTO CUE item.
The A.CUE indicator appears on the display when the
Auto Cue function is on.
Auto Ready
When the Auto Ready function is on, after a track
finishes playing, playback will pause at the start of
the next track.
NOTE
If the Auto Cue function is also on, playback will
pause at the first moment of sound rather than
the start of the next track.
Turn this function on and off using the Setup menu
AUTO RDY item.
The A.RDY indicator appears on the display when the
Auto Ready function is on.
CD text data display
Press the TIME/ENTER/TITLE key while holding
down the SHIFT key to change the information displayed when using discs with CD text data.
Track title (TITLE)
Artist name (NAME)
CD text data will automatically disappear from the
display after about twenty seconds.
TASCAM CD-DJ1
15
5- DJ functions
The unit's DJ functions include Cue, Hot Cue (Flash Start), Loop playback, Tempo control, and Pitch bend.
Cue
A cue point can be set that allows you to pause playback and jump to that point by pressing the CUE key.
Setting the cue point
The two modes for setting cue point are as follows.
ª
Play mode (default setting):
The cue point is automatically set as the last playback
start point.
ª
Cue mode:
The cue point is set as the point where the unlit CUE
key is pressed when the CD is paused or during scrub
playback.
The setting can also be changed by selecting PLAY or
CUE in the Setup menu CUE KEY item.
NOTE
The CUE key lights when a cue point is set. When
the mode setting is CUE, the key will flash during
pause or scrub playback.
The cue point is canceled when the CD cover is
opened.
Press the CUE key while holding down the SHIFT
key to display the current mode (PLAY or CUE) briefly.
Change the mode by pressing the CUE key again
while the mode is displayed.
Using and confirming the cue point
By pressing the CUE key once, you can pause playback and jump to the cue point. If you press and hold
down the CUE key again, playback continues from
the cue point until you release the key.
The cue point can be confirmed using this function.
To resume normal playback, press the PLAY/PAUSE
key during playback while holding down the CUE
key.
When you release the CUE key, playback pauses and
the playback position resets to the same cue point.
Hot Cue
The CD-DJ1 has two HOT CUE keys (1 and 2) that
allow you to set independent Hot Cue points. After
a Hot Cue point has been set, pressing its HOT CUE
key either starts or pauses playback at that point.
Setting Hot Cue points
Press an unlit HOT CUE key during playback, pause,
or scrub playback. The Hot Cue point for that key
will be set and the key will light up.
16 TASCAM CD-DJ1
Use the Setup menu FLASH Start item to set whether
HOT CUE keys start or pause playback (see “Flash
Start” on page 17).
5- DJ functions
Canceling Hot Cue points
Cancel a Hot Cue point by pressing its HOT CUE/
CLEAR key while holding down the SHIFT key.
Opening the CD cover also cancels the Hot Cue
points.
Using and confirming Hot Cue points
When Flash Start is off, you can jump to a Hot Cue
point and pause playback by pressing a HOT CUE
key. If you press and hold down that HOT CUE key
again, playback continues from that HOT Cue point
until you release the key.
When you release the HOT CUE key, playback paus-
es and the playback position is reset at the Hot Cue
point. Hot Cue points can be confirmed using this
function.
To resume normal playback, press the PLAY/PAUSE
key during playback while holding down a HOT CUE
key.
Flash Start
Use the HOT CUE keys for instant playback from
their cue points when the Flash Start function is on.
Turn the Flash Start function on and off with the
Setup menu FLASH item (the default setting is on).
When Flash Start is on, the FLS indicator appears on
the display.
Loop playback
Use this function to loop playback of any section of
an audio CD between set IN and OUT points.
The following procedure explains how to set and play
a loop section with starting (IN) and ending (OUT)
points.
Setting the IN point
Press the IN key while the CD is playing or paused.
The IN key will light up and the OUT key will flash.
Setting the OUT point
Press the OUT key while the CD is playing or
paused. The IN, OUT and RE-LOOP/EXIT keys will
all light up.
Loop playback will start immediately if the OUT
point is set while the CD is playing.
Setting the OUT point while the CD is paused moves
the pause position to the IN point. Push the PLAY/
PAUSE key to begin loop playback.
During loop playback, as soon as the OUT point
is reached, playback restarts instantly from the IN
point.
NOTE
The OUT point can only be set at a time following
the IN point.
The OUT point can be set to create a loop that
spans more than one track.
Canceling loop playback
Press the RE-LOOP/EXIT key during loop playback
to exit the loop mode and resume normal playback.
The key's light will turn off, but the loop IN and
OUT points will not be cancelled.
Using a SKIP, CUE or HOT CUE key to set the current location outside the looped section will also exit
loop playback mode. The RE-LOOP/EXIT key light
will turn off, but the loop points will not be canceled.
TASCAM CD-DJ1
17
5- DJ functions
Re-loop playback
Press the RE-LOOP/EXIT key to restart loop playback immediately when it is off but the IN and OUT
points are still set.
Press the IN key for immediate playback from the IN
point when it is set (like a HOT CUE key).
Canceling loop points
Cancel the loop (IN and OUT) points with either of
the following actions.
The IN and OUT key lights will turn off when the
loop points are canceled.
Press the RE-LOOP/EXIT key while holding down
the SHIFT key. Alternatively, open the CD cover.
Changing the OUT point
Press the OUT key during loop playback to change
the OUT point and restart loop playback from the IN
point. The new OUT point is determined according
to the Setup menu OUT KEY setting.
ª
HALF
The new OUT point is set to a point halfway between
the IN point and the OUT point.
ª
SET
The OUT point is set at the location where the OUT
key is pressed during playback.
Adjusting the OUT point
Press the OUT key while holding down the SHIFT
key to enable use of the JOG dial for editing the OUT
point during loop playback. Turn the dial clockwise
to lengthen the loop (or counterclockwise to shorten
it) during playback until the desired OUT point is
reached. Press the OUT key at the desired moment
to set the new OUT point and exit OUT point adjustment mode.
The adjustment will affect the loop playback in real
time.
Restoring the OUT point
Press the IN key while holding down the SHIFT
key during or after adjustment of the OUT point to
restore the OUT point to its pre-adjustment position
(the display shows OUT RET).
Tempo control
Use the tempo slider to control playback speed. The
display shows the current tempo adjustment.
Push the slider in the “–” direction to slow the tempo,
and pull it in the “+” direction to speed it up.
Setting the tempo range
Use the TEMPO key to change the tempo slider
range. Press the TEMPO key to cycle through the following tempo ranges.
±8% (default setting), ±16%, ±32%, ±100%
The new range setting becomes effective after it
flashes on the display for a few seconds.
18 TASCAM CD-DJ1
NOTE
When an attached TT-M1 is turned on, the tempo
slider and TEMPO key do not function. Playback
tempo value is set by the TT-M1 (see "TT-M1 use"
on page 22).
5- DJ functions
Key Original function
The Key Original function allows you to change the
tempo without changing the pitch (key).
The Key Original function can also be turned on and
off in the Setup menu under the KEY ORIG item.
NOTE
The Key Original function cannot be used when
the tempo range is set to ±100%. Setting the
tempo range to ±100% automatically turns off the
Key Original function.
The Key Original function cannot be used when the
TT-M1 is on. Turning on the TT-M1 automatically
turns off the Key Original function.
The K.ORIG indicator appears on the display when the
Key Original function is on.
Turn the Key Original function on and off by pressing the TEMPO/KEY ORIG key while holding down
the SHIFT key.
Pitch bend function
Pitch bend temporarily speeds up or slows down the
playback speed and changes the playback pitch (if
the Key Original function is turned off).
Use the Setup menu SRCH KEY item to set whether
the pair of SEARCH keys or the JOG dial controls
pitch bend.
The Maximum pitch bend is ±16%.
ª
ª
When set to BEND:
Use the SEARCH keys for pitch bend and the JOG
dial for searching. Press and hold either key during
playback to change the tempo. Release the key to
restore the original playback tempo.
NOTE
When the Key Original function is on, bending the
pitch will change the tempo, but not the pitch.
When set to SRCH:
The SEARCH keys are used for searching. Use the
JOG dial for pitch bend. Turn it clockwise to speed
up and counterclockwise to slow down playback.
Stop turning to return to the original speed (as
adjusted by the tempo slider).
NOTE
When set to SRCH, the SEARCH keys function as
normal search keys (see "Track search" on page
15). However, pressing a SEARCH key while holding down the SHIFT key will cause pitch bend.
TASCAM CD-DJ1
19
6- MP3 playback
This unit can play back MP3 file discs that meet the
following requirements.
• Disc: CD-ROM MODE 1 (Multi-session discs are
unsupported, but playback of the files in the first
recorded session is possible.)
•
•
•
•
Bit rate: 32 to 192 kbps (VBR is not supported)
Sampling frequency: 44.1k Hz, mono or stereo
File extensions: mp3, Mp3, mP3, MP3
ID3 tags are supported.
• File format: MPEG 1 Audio Layer 3
Playback range selection
MP3 file playback can be set to either play all tracks
in the currently selected folder or all tracks on the
disc (in all folders). Use the Setup menu FOLDER
item to choose this option.
ª
Folder selection
Press a SKIP key while holding down the SHIFT key
to select folders.
Set the FOLDER menu item to OFF (default setting)
to select complete disc playback. Set it to ON to play
only the tracks in the selected folder.
Display indication
• MP3 appears on the display during MP3 playback.
• The time display mode is always ELAPSED (track
time elapsed). REMAIN and TOTAL REMAIN are not
used with MP3 files.
• Press the TIME/ENTER/TITLE key while holding
the SHIFT key to change the MP3 information
display.
Track titles (TITLE)
File names (FILE)
Functions disabled during MP3 playback
The following functions cannot be used during MP3
playback.
•
•
•
•
•
Track search
JOG dial operation (scrub playback)
Cue
Hot Cue
Loop playback
20 TASCAM CD-DJ1
• The total track number displayed depends on the
Setup menu FOLDER setting. The number shown
is either the total number of MP3 files in the current folder or the total number on the disc.
6- MP3 playback
MP3 file folders and tracks
MP3 files recorded onto a CD are handled the same
way as files are handled in an ordinary PC, with
some MP3 files held within a folder. In addition,
several folders can be combined into one folder. This
results in multiple layers of folders and files.
NOTE
Each MP3 file is handled as a track.
MP3 files are played in the following order.
Disc
Folder A
Folder B
Folders that do not contain MP3 files directly
under them cannot be selected for playback. For
example, in the diagram here, under folder A are
folder B and folder C. If there are MP3 files in both
folders B and C, folder A cannot be selected for
playback, but folder B and C can be selected for
playback.
1
2
3
4
5
Folder C
The CD-DJ1 can play back MP3 files recorded in
formats that conform to ISO9660 level 1, level 2, and
the Joliet extensions.
CDs containing MP3s to be played by the CD-DJ1
have their contents must be within the following
maximum limits:
MP3 files
6
7
Folder D
8
9
Number of folders: 255
Number of hierarchical structures: 8
Number of MP3 files: 999
Title length of MP3 files and folders: 255
In this manner, playback proceeds from the top level
folders.
TASCAM CD-DJ1
21
7- Other features
TT-M1 use
The CD-DJ1 has a TT-M1 jack for connecting a
TASCAM TT-M1 (sold separately). An analog turntable with an attached TT-M1 connected to the unit
by this jack can be used to control CD playback
speed and direction.
Turning the TT-M1 on and off
Use the switch on the TT-M1 to turn it on and off.
When the TT-M1 switch is turned on, the TT-M1
controls CD playback speed and direction. The LED
on the TT-M1 lights when it is on.
When the TT-M1 switch is off, the TT-M1 does not
function and its LED is not lit.
TT-M1 Calibration
Calibration is necessary before using the TT-M1.
1. Press the TT-M1 power switch.
2. Run the analog turntable at regular speed (33
rpm at 0% tempo adjustment).
3. Push the PLAY/PAUSE key while holding
down the SHIFT key on the CD-DJ1. Alternatively, select the Setup menu TTM CAL item
and press the ENTER key.
4. Calibration starts.
display during calibration.
appears on the
NOTE
Calibration measures the TT-M1 sensing conditions (signal pulse rate and wow amount) during
analog turntable playback at 33 rpm to optimize
the CD-DJ1 for accurate playback control by the
TT-M1.
If the analog turntable rotation is unstable or extremely fast or slow, calibration will not complete
correctly and the measurements will be ignored.
will appear on the display.
5. If calibration completes correctly,
appears on the display.
Functions disabled during TT-M1 use
The following functions and operations are disabled
during TT-M1 use.
• Tempo adjustment using the tempo slider
• Tempo range change
• Pitch bend using the JOG dial or track SEARCH
keys
• Key Original function (automatically turned off)
Resetting the unit
Use the Setup menu RESET item to restore all the
settings and information to the factory-set defaults.
When the menu cursor is aligned with the RESET
item, press the ENTER key.
will appear on
the display. Press the ENTER key again to reset the
unit. Press any other key to cancel.
22 TASCAM CD-DJ1
The TT-M1 is disabled when the CD-DJ1 search
functions are used.
7- Other features
Setting output volume
Use the Setup menu D.ATT item to adjust the output
volume from the CD-DJ1 LINE OUT and PHONES
OUT jacks.
Adjustment can be made between 0 dB and –20 dB
in 1 dB steps. The default value is 0 dB.
Auto Play
Use the Setup menu AUTOPLAY item to turn Auto
Play on and off. With this function on, playback will
begin as soon as the CD-DJ1 power is turned on. The
default setting is off.
Adjusting the backlight
Set display backlight brightness in the Setup menu.
Use the DIMMER item to adjust the brightness
between levels 1 and 5.
When the unit enters sleep mode, the backlight turns
off.
Adjusting the contrast
Use the Setup menu LCD CONT item to adjust the
display contrast value between 1 and 10.
TASCAM CD-DJ1
23
8- Specifications
Specifications
Playable disc size
8 cm (3-inch), 12 cm (5-inch)
Types
CD, CD-R, CD-RW
Formats
Audio (CD-DA),
Data CDs in IS09600 Level 1 and 2, Joliet format, containing MP3 files
Number of channels
2
Sampling bit rate
16 bits
Sampling frequency
44.1 kHz
Line Out
RCA pin jack x 2
Output impedance 600 Ø or less
Maximum output level +6 dBV
Phones Out
1/4” (6.3 mm) stereo phone jack
Maximum output 20 mW + 20 mW (into 32 Ø)
TT-M1 input jack 6-pin mini-DIN
Power
U.S.A./Canada
U.K./Europe
Australia
120 V AC. 60 Hz
230 V AC. 50 Hz
240 V AC. 50 Hz
Power consumption
U.S.A./Canada
U.K./Europe/Australia
6W
6W
Dimensions (W x D x H)
155 x 275 x 60 (mm) / 6.10 x 10.83 x 2.36 (in)
Weight
1000 g / 35 oz
Audio performance
Frequency response
20 Hz ~ 20 kHz, +/-0.5 dB
Dynamic range
> 96 dB
Signal-to-noise ratio
> 100 dB (with A-FILTER)
Total harmonic distortion
< 0.005%
Channel separation
> 98 dB (at 1 kHz, with A-FILTER)
Note: All measurements are made with tempo change at 0%.
24 TASCAM CD-DJ1
8- Specifications
Backup memory
This unit maintains the following settings even when
the power is turned off.
Setup menu settings (all except for the
system reset parameter)
ª
Other settings
Tempo control settings
Playback and repeat mode
Playback time display mode
Key Original
Digital Attenuation
TT-M1 Calibration
Auto Cue
Auto Ready
CD-ROM Folder play
Flash Start
Auto Play
CUE Key mode
Loop OUT Key mode
SEARCH Key functions
LCD Contrast
Backlight Dimmer
Dimensional drawing
275 mm
10.83"
ª
155 mm
6.10"
60 mm
2.36"
TASCAM CD-DJ1
25
Notes
26 TASCAM CD-DJ1
Notes
TASCAM CD-DJ1
27
»
CD-DJ1
TEAC CORPORATION
Phone: +81-422-52-5082
3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550 Japan
www.tascam.com
TEAC AMERICA, INC.
Phone: +1-323-726-0303
7733 Telegraph Road, Montebello, California 90640 U.S.A.
www.tascam.com
TEAC CANADA LTD.
Phone: +1905-890-8008 Facsimile: +1905-890-9888
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8 Canada
www.tascam.com
TEAC MEXICO, S.A. De C.V
Phone: +52-555-581-5500
www.tascam.com
Campesinos No. 184, Colonia Granjes Esmeralda, Delegacion Iztapalapa CP 09810 Mexico DF
TEAC UK LIMITED
Phone: +44-8451-302511
Unit 19 & 20, The Courtyards Hatters Lane, Watford, Hertfordshire. WD18 8TE U.K.
www.tascam.co.uk
TEAC EUROPE GmbH
Phone: +49-611-71580
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany
www.tascam.de
Printed in China