Sanyo VCC-6975P Digital Camera User Manual
Add to my manualsadvertisement
x32 Electronic sensitivity (minimum illumination of 0.05 Lux)
VCC-6975P
Colour
PAL
Accredited by the RvA
ISO 9001 REGISTERED FIRM
DNA Certification B. V., THE NETHERLANDS
*Specifications subject to change without notice
*Caution: please consult the instruction manual to ensure safe and proper operation of the product.
Horizontal TV Lines
SF-1407MV
1/3" Colour CCD
High-resolution Camera
VCC-6975P
Shown with optional lens
An all-new Intelligent Digital Motion Detector is built-in to detect moving objects in the picture and send an alarm
The intelligent Digital Motion Detector analyzes changes in picture brightness on the screen and uses the direction of motion and size of the object to identify moving objects. The system can be set to produce an external alarm signal and/or switch to a x2 digital zoomin display. Furthermore, the center of the zoom-in picture stays focussed on the moving object.
x2 zoom
CAMERA 1
x2 zoom
CAMERA 1
Display of monitor
Intelligent digital motion detector uses size of object and direction of motion to identify moving objects.
Display of monitor
Detection of a moving object prompts the camera to zoom in on the object (x2), and blinking camera ID is displayed on the monitor. An external alarm signal is also sent.
Display of monitor
During the zoom-in display, the center of the picture travels and stays focussed on the object.
Duration of the zoom-in display is adjustable to
5, 10, 20, 30, and 60 seconds.
Reliable detection of moving objects
The intelligent Digital Motion Detector uses seven factors in analyzing changes in picture brightness to enable reliable motion detection and reduce false alarms.
1 4
Direction
It is possible to narrow the target to objects moving in certain directions only. This feature enables the system to detect people coming into a room while disregarding people going out. It is also possible to detect all moving objects without setting the direction.
5
Magnitude of movement
Set the magnitude of movement to be detected.
DIRECTION CAMERA 1
Brightness
Set the lowest level of brightness to be analyzed. Use this feature to avoid influences of electric noises on the darker area of the screen.
Brightness
Not detection
Noise
Set the direction to “right”
2
3
Size
Freely set the size of target objects.
Masking
Freely establish the area where motion detection is turned off.
An area where motion detection is turned off
6
7
Time
Magnitude of brightness shift
Set the magnitude of changes in brightness. This feature is used to disregard a sudden and huge change in brightness such as one caused by turning on/off the lights.
Duration
Set the time the system should continue monitoring before identifying a moving object. This feature enables the system to neglect high speed objects such as automobiles.
*The intelligent Digital Motion Detector function is not available when the electronic sensitivity is set to ON or when the electronic shutter is set to “long mode”.
10
1
15
5
10
Features
x32 electronic sensitivity
When the illuminance of the monitoring point drops down, electronic sensitivity can be automatically increased to x32
(max.) to brighten up the image. The minimum illuminance on the object is 0.05 Lux (using F1.2 lens) which makes it possible to obtain a clear picture with almost no light at all.
The automatic increase in gain can be set to x2, x4, x8, x16, or x32.
The camera can even cope with a gradual and continuous change in illuminance from day to night and maintains a crisp picture by successive adjustments of the auto iris, auto gain control, and electronic shutter.
When the electronic sensitivity is set to ON
High quality image with DSP
The adoption of a new DSP (Digital Signal Processor) has brought up the quality standard of the monitored image for reliable surveillance.
1) By digitizing the Colour processing, Colour reproduction has been largely enhanced.
2) DSP maintains crisp borders and also restricts smear and smudges of Colour. It further enables a wide choice of settings to control the degree of edge compensation.
On-screen settings
Camera settings can be easily controlled through on-screen menus. A new setting will be reflected on the monitor to make optimum settings easy.
Menu languages built in: English / French / Germany x8 digital zoom with digital pan and tilt
Digital zoom of x2, x4, and x8, or continuous zooming up to x8 is available. The center of zooming can also be moved around in all directions. Zooming can be controlled via SSP or by means of a remote control circuit.
Two types of backlight compensation with fine tuning
1) Multi-spot photometry mode setting
This mode enables the user to specify screen areas, among 32 blocks, in which illuminance measurements will not take place.
The picture display will be kept to optimum brightness according to the illuminance measurements obtained in other areas.
Areas in which illuminance will not be measured
Three types of white-balance adjustment
1) Automatic tracking mode to adjust white-balance as the light
(Colour temperature) at the monitoring point changes.
2) Push-and-lock mode to adjust white-balance when the set button is pushed.
3) Manual white-balance by adjusting R and B volume.
Camera ID display
An 8-character (max.) camera ID can be super-imposed on the monitor. The user can change the display to any position on the screen.
Three types of synchronization
Internal, line lock, or external sync. can be selected. Selection
= between internal and line lock sync. mode is done on-screen. The camera automatically switches to external sync. mode by receiving a VBS. (Line lock sync. mode is available only with 24 V AC power supply.)
Dual power operation
24 V AC or 12 V DC applicable.
13 mode electronic shutter
Short mode: 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, and 1/10000 sec.
Long mode: 2/50, 4/50, 8/50, 16/50, and 32/50 sec.
1/3" CCD image sensor with approx. 470,000 picture elements
480 TV lines of horizontal resolution
Electronic iris (indoor use)
S S P
Security Serial Protocol
SSP (RS-485) compatibility
The whole security system, including the VCC-6975P, may be controlled by a VSP-7000 system controller using a new communication protocol SSP (Security Serial Protocol).
Remote control functionality on VSP-7000 includes all on-screen menu items of the VCC-6975P.
SSP: Bi-directional communications (half duplex)
Maximum cable length for communication up to 1200 m (4000 feet)
VCC-6975P VCC-6975P VCC-6975P VCC-6975P
Command
Alarm
Up to 256 devices
2) 5-section photometry mode setting
The screen will be divided into 5 sections to which the user will assign 15-scale weights.
The brightness of the picture will be kept at optimum by giving priority to the area with the higher weight. (A DC type auto-iris lens is required to enable this mode.)
An example of weight setting:
Top = 1, Bottom = 5, Left = 10,
Right = 10, Center (fixed) = 15.
The size and position of the center area is adjustable.
Multiplexer VCR VSP-7000
System Controller VSP-7000 (sold separately)
VCC-6975P rear panel
Video output terminal
Type of coaxial cable and maximum length
• Cable type RG-59U (3C-2V), 250 m maximum
• Cable type RG-6U (5C-2V), 500 m maximum
• Cable type RG-11U (7C-2V), 600 m maximum
Y/C signal output terminal
Type of coaxial cable and maximum length
• Mini-DIN round type 4-pin, 10 m maximum
SSP terminal
Power supply terminals
24 V AC and 12 V DC dual power capability eliminates limitations on camera location.
Synchronization signal input terminal
Camera Set-up Unit
VAC-60
(sold separately)
Remote set-up makes you feel you have the camera right beside your monitor. Capable of setting up VCC-6975P for all on-screen menu items (intelligent digital motion detector, backlight compensation, white-balance, etc.)
For better picture quality, disconnect this unit after settings are completed.
CURSOR
SET
VCC-6975P
LENS
VCC-6975P 67
1
136
126.5
9.5
VAC-60 rear panel
CURSOR
SET
LENS
ADJ.
LOCK
FLANGE BACK
DIGITAL
COLOR CCD CAMERA
LENS 4-pin
(Unit: mm)
28
15.4
25.2
1/4"–20 UNC threaded hole
(top / bottom selectable)
MODEL VCC-6975P
Scanning system
Image sensor
Picture elements
Horizontal resolution
Minimum illumination
Electronic sensitivity
Video output level
Video S/N ratio
Backlight compensation
Dimensions (approx.)
Weight (approx.)
PAL standard 625 lines, 25 frames/sec.
1/3" (approx. 4.8 mm x 3.6 mm) interline transfer method CCD
Total: 795(H) x 596(V), Effective: 752(H) x 582(V)
480 TV lines
Approx. 0.05 Lux (F1.2, x32 electronic sensitivity)
Approx. 1.4 Lux (F1.2, normal mode)
ON / OFF ––– (on screen)
ON = x2 / x4 / x8 / x16 / x32 ––– (on screen)
1.0 V (p-p) (75 ohms, composite)
More than 48 dB
Multi-zone light measuring system
ON / OFF ––– (on screen)
White balance
Gain control
Gamma
Electronic shutter
Light control
Lens mount
Flange back
Auto iris lens
Auto iris output
Lens iris level
Electronic iris
Electronic iris range
Synchronizing system
V phase adjustment
Motion detector
ON = Multi-spot photometry / 5-section photometry ––– (on screen)
(TTL) ATW / AWC / Manual ––– (on screen)
ON (Automatic) / OFF ––– (on screen)
ON (
γ
= 0.45) / OFF ––– (on screen)
Short mode: 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 sec. ––– (on screen)
Long mode: 2/50, 4/50, 8/50, 16/50, 32/50 sec. ––– (on screen)
Optical auto iris lens / Electronic iris (indoor use)
CS / C mount (C mount: using C-mount adaptor supplied)
12.5 mm
±
0.5 mm adjustment
DC / VIDEO ––– Slide SW (side)
DC: Drive coil (+, -), Brake (Damp) coil (+, -)
VIDEO: +12 V DC (Max. 50 mA), Video output (high-impedance)
LEVEL: L~H ––– (on screen)
ON / OFF ––– (on screen)
1.4 Lux to 70,000 Lux (F1.2), 2.0 Lux to 100,000 Lux (F1.4)
Internal sync. / Line lock ––– (on screen)
External sync.
automatic switching
LINE PHASE ––– (on screen)
ON / OFF ––– (on screen)
Alarm out: RS485 (G, B, A) and ALARM (C, A)
Electronic zoom
Mirror image effect
Camera ID
Sockets
ON / OFF ––– (on screen)
ON = Continuance (up to x8), Fix (x2 / x4 / x8), Pan / tilt operation
H, V, H/V, 3 mode reverse image
ON (up to 8 characters) / OFF ––– (on screen)
Video signal VIDEO OUT ––– BNC (rear)
Y/C signal out mini-DIN 4-pin (rear)
SSP (RS-485) RS485 (G, B, A) ––– Pushbutton terminal x 1 pair (rear)
Alarm signal ALARM (C, A) ––– Pushbutton terminal x 1 pair (rear)
External sync.
Auto iris lens
VBS IN ––– BNC (rear)
LENS ––– 4-pin (side)
Power supply
Environmental conditions
Power requirement
Power consumption (approx.)
Camera mount
24 V AC, GND ––– 3-pin terminal (rear) 12 V DC ––– 2-pin terminal (rear)
Temperature: -10
°
C to 50
°
C [14
°
F to 122
°
F], Humidity: within 90% RH
24 V AC, 50 Hz or 12 V DC
24 V AC: 4.0 W (with auto iris lens), 12 V DC: 4.1 W (with auto iris lens)
1/4"–20 UNC (top / bottom selectable)
67(W) x 54(H) x 126.5(D) mm
[2.64(W) x 2.13(H) x 4.98(D) in.] (w/o camera & lens mounts)
470 g [16.6 oz.] (w/o lens)
VAC-60
MODEL
Video output terminal
Camera input terminal
Environmental conditions
Power requirement
Dimensions
Weight (approx.)
Monitor
VAC-60
BNC x 1
BNC x 1
Temperature: 0
°
C to 40
°
C [32
°
F to 104
°
F], Humidity: 10 to 90%
3 V DC, Alkali type AAA format batteries x 2
90(W) x 135(H) x 36(D) mm [3.54(W) x 5.32(H) x 1.42(D) in.]
230 g [8.1 oz.]
AC adaptor
(for VCC-6975P)
VCA-35E
(sold separately)
MODEL
Power requirement
Power consumption (approx.)
Dimensions (approx.)
Weight (approx.)
VCA-35E
220 ~ 230 V AC, 50 Hz
17 VA max.
68(W) x 62(H) x 100(D) mm [2.68(W) x 2.44(H) x 3.94(D) in.]
680 g [24 oz.]
Lenses for 1/3" CCD camera
Super Wide-angle Lens
Wide-angle Lens
Standard Lens x 6 Manual Zoom Lens
VCL-CS2LYA
VCL-CS4LY
VCL-CS8LY
VA-TS6ZE-LY x 6 Motorized Zoom Lens x 10 Motorized Zoom Lens
Pinhole Lens
Vari-focal Lens
VA-TS6ZME-LY
VA-TS10ZME-LY
VA-TS420PE-LY
VA-TS2VE-LY
SSP corresponding devices
As of March 2000
System Controller
SSP System Controller VSP-7000
Multiplexer
16-channel Duplex Multiplexer (Colour)
16-channel Duplex Multiplexer (B/W)
9-channel Duplex Multiplexer (Colour)
9-channel Simplex Multiplexer (B/W)
MPX-CD162P
MPX-MD162P
MPX-CD92P
MPX-MS92P
Realtime VCR
168-hour Recording + Realtime VCR
40-hour Recording + Realtime VCR
SRT-7168P
SRT-6000P
Time Lapse VCR
960-hour Recording Time Lapse VCR
168-hour Recording Time Lapse VCR
24-hour Recording Time Lapse VCR
TLS-9960P
TLS-9168P
TLS-9024P
*More models will be introduced soon.
Distributed by:
please consult the instruction manual to ensure safe and proper operation of th e product.
SANYO Electric Co., Ltd.
Video Imaging Systems Division
© 2000 SANYO Printed in Japan '00.3. AP
1/3" Colour CCD
High-resolution Camera
Built in DSP (digital signal processing) circuit
Intelligent digital motion detector x32 Electronic sensitivity (minimum illumination of 0.05 Lux) x8 Digital zoom with digital pan and tilt
480 TV lines of horizontal resolution
SSP compatible
Dual power operation, 24 V AC / 12 V DC
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project