advertisement
Owner's Manual
®
4.0 HORSEPOWER
20" SIDE DISCHARGE
ROTARY LAWN MOWER
Model No.
917.387023
Safety e Assembly
• Operation o
Maintenance
o Espa5ol
Repair Parts
CAUTION'.
Read and follow all
Safety Rules and Instructions before operating this equipment
Sears, Roebuck and Co,, Hoffman Estates, IL 60179
Warranty
Safety Rules
Assembly
Operation
Maintenance Schedule
Maintenance
2 Product Specifications
2 Service and Adjustments
4 Storage
6 Troubleshooting
10 Repair Parts
10 Parts Ordering
11 t3
14
15
32
Back Cover
LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER
For two years from date of purchase, when this Craftsman Lawn Mower is maintained, lubricated, and tuned up according to the operating and maintenance instructions in the owner's manual, Sears will repair free of charge any defect in material or workmanship.
if this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.
This Warranty does not cover:
• Expendable items which become worn during normal use, such as rotary mower blades, blade adapters, belts, air cleaners and spark plug.
o Repairs necessary because of operator abuse or negligence, including bent crank, shafts and the failure to maintain the equipment according to the instructions contained in the owner's manual.
Warranty service is available by returning the craftsman power mower to the nearest sears service center/department in the united states.
This warranty applies only while this product is in use in the united states.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state,
SEARS, ROEBUCKAND CO,, D/817 WA, HOFFMAN ESTATES, ILLINOIS 60179
TRAINING:
o Read this operator's manual carefully,.
Become familiar with the controls and know how to operate your mower properly.
Learn how to quickly stop mower.
,, Do not allow children to use your mower.
Never aIlow adults to use mower without proper instructions, o Keep the area of operation clear of all persons, especially small children and pets, o Use mower only as the manufacturer intended and as described in this manual.
o Do not operate mower if it _has been dropped or damaged in any manner..
Always have damage repaired before using your mower,
° Do not use accessory attachments that are not recommended by the manufac-
turer. Use of such attachments may be hazardous.
o The blade turns when the engine is running.
PREPARATION: o Always thoroughJy check the area to be mowed and clear it of a]! stones, sticks, wires, bones, and other foreign objects.
These objects wilt be thrown by the blade and can cause severe injury.
• Always wear safety glasses or eye shields when starting and while using your mower.
• Dress properly.
Do not operate mower when barefoot or wearing open sandals,
Wear only solid shoes with good traction when mowing.
, Check fuel tank before starting engine..
Do not fil! gas tank indoors, when the engine is running or when tile engine is
hot..Allowthe enginetocootfor several minutesbeforefillingthe gastank. Clean off anyspilledgasolinebeforestartingthe engine..
Alwaysmakewheelheightadjustments beforestartingyourmower.Never
attemptto do this whilethe engineis running.
Mow onlyin daylightor goodartificial light.
OPERATION:
o Keep your eyes and mind on your mower and the area being cut. Do not let other interests distract you° o Do not mow wet or slippery grass.
Never run while operating your mower.
A!ways
be sure of your footing -keep a firm hold on the handles and walk.
o Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times, o Always stop the engine whenever you leave or are not using your mower, or before crossing driveways, walk,s, roads, and anjj gravel--covered areas.
Never direct discharge of material toward bystanders nor allow anyone near the mower while you are operating it.
o Before cleaning, inspecting, or repairing your mower, stop the engine and make abso!utely
Sure the blade and all moving parts have stopped.
Then disconnect the spark plug wire and keep it away fromthe spark plug to prevent accidental starting.
o Do not cOntinue to run your mower if you hit a foreign object, Follow the procedure outlined above, then repair any damage before restart!ng
and operating you mower°
o Do not change the governor settings or overspeed the engine.
Engine damage or personal injury may result.
o Do not operate your mower if it vibrates abnormally.
Excessive vibration is an indication of damage; step the engine, safely check for the cause of vibration and repair as required° o Do not run the engine indoors.
Exhaust fumes are dangerous.
.
Never cut grass by pulling ttte mower towards you. Mow across the face of slopes, never up and down or you might lose your footing.
Do not mow excessively steep slopes.. Use caution when operating the mower on uneven terrain or when changing directions -- maintain good footing,.
o Never operate your mower without proper guards, plates, grass catcher or other safety devices in place,
MAINTENANCE AND STORAGE: o Check the blade and the engine mounting bolts omen to be sure they are tightened properlyr o Check all bolts, nuts and screws at frequent intervals for proper tightness to be sure mower is in safe working condition.
o Keep all safety devices in place and wo,rking, o To reduce fire hazard, Reep the engine free of grass, leaves or excessive grease and oil,
° Check grass catcher often for deterioration and. wear and replace worn bags.
Use only replacement bags that are recommended by and comply with specifications of the manufacturer of your mower.
• Always keep a sharp blade on your mower.
,, Allow engine to cool before storing in any enclosure.
o Never store mower with fuel tn the tank inside a building where fumes may reach an open flame or an ignition source such as a hot water heater, space heater, clothes dryer, etc
CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs.
WARNING: The engine exhaust from this product contains chemicals known to the
State of California to cause cancer, birth defects, or other reproductive harm.
3
wereavailablewhenthis lawn mowerwas produced. They are als0 availableat mostSears retailoutlets_nd servicecenters. MostSearsstorescan also
order repair parts for you, when you provide the model number of your lawn mower.
Some of these accessories,may not apply to your lawn mower,
FOR REAR D1SOHARGE LAWN MOWERS
GRASS CATCHERS
FOR
REAR DISCHARGE
'[.AWNMOWERS
LAWN
MOWER MAINTENANCE
,, MULCHER KITS,
.
; "_GRASS CATCII'I_RS
FOR
' SIDE DISCHARGE
:I_AWN MQWE'RS
STABIL[ZP-R
GAS .CANS
SPARK PLUGS
BLADE AZ}A'PTERS
._HEELS
E_GIt_E0_. I
Read these instructions and this manual in its entirety before you attempt to. assemble or operate your new lawn mower.
Yo[_r new lawn mower' has been assembled at the factory with the e×ception of those parts, left unassembled for shipping purposes.
All parts such as nuts, washers, bolts, etc,, necessary to complete the assembly have been placed in the parts bag, To ensure sefe and proper operation of your lawn mower, al! parts and hardware you assemble must be tightened securely.
Use the correct tools as necessary to ensure proper tightness.
TO REMOVE
CARTON
LAWN MOWER FROM o Remove loose parts included with mower.
o Cut down two end corners
of
carton and lay end panel down flat.
o Remove all packing materials except padding between upper and .lower handle and padding holding operator presence control bar to upper handle.
= Rot! lawn mower out of carton and check carton thoroughly for additional loose parts.
HOW
TO
SET UP YOUR LAWN
MOWER
TO UNFOLD HANDLE
B_PORTANT: Unfold handle carefully so as not to pinch or damage control cables.
Operator presence control bar "'-..
, Lift up _'./_._____ _r up/_'A_ r/
Lower h
4
,, Raisehandlesuntillower handlesection locksinto placein mowingposition.
,, Removeprotectivepadding,raiseupper handlesectioninto place on lower handleandtightenboth handleknobs,
• Removehandlepaddingholding operatorpresencecontrolbar to upper handle.
Yourlawn mowerhandlecan be adjustedfo[.yobrmowingcomfort.
Refer'to "Adjust Handle"in the Service andAdjustmentssectionof this _anuaL
KNOW
YOUR
LAWN
MOWER
READ THIS OWNER'S MANUALAND SAFETY RULES BEFORE OPERATING Y_UB LAWN
MOWER.
Compare lhe illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments.
Save this manual for future reference.
These symbols may appear on your lawn mower or in literature supplied with the product Learn and understand their meaning.
CAt_IT_ON
OR WARNING
ENG_N_
Ofl
_NGINE
OFF
Engine zone control cable
FA_T
SLOW CHOK_
FUEl, OiL
DANOFR.
K_EP HANDS
AN[} FEE]"
AWAY
_erator presence control bar
- Upstop brackel
Starter handle
Handle knob
Cable clip
Engine oil cap with dipstick
Gasoline fill cap
Primer
Discharge guard
Housir_g
Mutcher plate
Wheel adjuster
(on each whee!)
MEETS CPSC SAFETY REQUIREMENTS
Sears rotary walk-behind power lawn mowers conform to the safety standards of lhe American
National Standards Institute and the U.S. Consumer Product Safety Commission The blade turns when the engine is running.
Operator presence control bar- must be held down to the handle to start the engine.
Release to stop the engine
Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine,
Starter handle - used for starting ttle engine.
Mulcher plate - Located at the discharge opening must be removed bagging or discharging when converting operation., to
Theoperationof anylawnmowercan resultin foreignobjectsthrownintothe eyes,whichcan resultinsevereeyedamage.Alwayswear
safetyglassesor eyeshieldswhileoperating
Your lawn mower has been shipped ready for mulching operation, To convert to discharging or bagging operation:
TO CONVERT TO DISCHARGING MOWER
Your mower is shipped ready to be used as a mutcher.. To convertto bagging or discharging:
,, Lift discharge guard and remove mulcher
standardsafetyglasses
ENGINESPEED
plate.
o Mower can now be used for side discharg-
Theenginespeedwas setatthefactoryfor optimumperformanceSpeedis notadjustable.
ing or optional grass catcher can be attached
• To return to mulching operation, simply reinstall mulcher plate as shown.
ENGINEZONE CONTROL
CAUTION: Do not run your lawn mower without discharge guard, approved grass
enginecontroltobe installedonthisfawn mowerin orderto minimizetheriskofblade contactinjuryDonotunderanycircumstances attempttodefeatthe functionoftheoperator
catcher or mulcher plate in place.
Discharge guard
Mulcher
Piate
running.
o Yourlawnmoweris equippedwithan operatorpresencecontrolbarwhich requirestheoperatortobepositioned behindthefawnmowerhandletostartand operatethelawnmower.
Lower Wheels lor
High Cut
Plate Tab
(
Tab
BEFORE STARTING ENGINE
OIL
Raise Wheels for
Low Cut
TO ADJUST CUTTING HEIGHT
,, Raise wheels for low cut and lower wheels for high cut
,, Adjust cutting height to suit your requiremerits Medium position is best for most lawns.
", To change cutting height, squeeze adjuster lever toward wheel, Move wheel up or down to suit your requirements.
Be sure all wheels are in the same setting_
NOTE: Adjuster is properly positioned when plate tab inserts into hole in lever, Also, gposition adjusters (if so equipped) allow lever to be positioned between the plate tabs,
Your lawn mower is shipped without oil in the engine.
,, Be sure mower is level and area around oil fill is clean..
, Remove engine oil cap w/dipstick and fill to the full tine on the dipstick, o Use 20 ozs. of oil.. For type and grade of oil to use, see "ENGINE" in Customer
Responsibilities section of this manual.
• Pour oi! slowly.
Do not over fill.
• Check oil level before each use, Add oil if neede& Fill to full line on dipstick.
o To read proper level, tighten engine oil cap each time.
o Reinstall engine oil cap and tighten.
,, Change the oil after every 25 hours of operation or each season, You may need to change the oil more often under dusty, dirty conditions.
GAS
° Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane.
Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.
blendedfuels(calledgasoholor usingethanol or methanol)canattractmoisturewhichleads storage,Acidicgascandamagethefuel systemofanenginewhileinstorage_Toavoid
.
Pores in cloth grass catchers can become filled with dirt and dust with use and catchers will collect less grass,. To prevent
[his, regularly hose catcher off with water and let dry before using_ o Keep top of engine around starter clear and clean of grass clippings and chaff. This will help engine air flow and extend engine life.
MULCHING MOWING TIPS
emptiedbeforestorageof30 daysorlonger.
Drainthe fueltank,startthe engineandlet it rununtilfuellinesandcarburetorareempty..
Usefreshfuelnextseason_SeeStorage foradditional use
engine or carburetor cleaner products in fuel tank or permanent damage may occur.
....I-_--------_
Engine oil ....q__\-\ capwidipstiok ",._._--
TO START ENGINE
_.;_
Gasoline filler cap o To start a cold engine, push primer five
(5) times before trying to start.
Use a firm push° This step is not usually necessary when starting an engine which has already run for a few minutes.
° Hold operator presence control bar down to the handle and pull starter handle quickly.
Do not allow starter rope to snap back..
,, "To stop engine, release operator presence control bar.
NOTE: In cooler weather it may be necessary to repeat priming step& In warmer weather over priming may cause flooding and engine will not start.
If you do flood engine, wait a few minutes before attempting to start and do not repeat priming steps.
MOWING TIPS
, Under certain conditions, such as very tall grass, it may be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of grass clippings.
• For extremely heavy cutting, reduce the width of cut by overlapping previously cut path and mow slowly..
o For side discharge lawn mowers, cutting in a counf6r-cloc#¢ise direction, starting at the outside of the area to be cut, spreads grass clippings more even!y and puts less load on the engine.
fo keep clippings off of walt{ways, flower beds, etc., make the first cuts in a clocl_ise direction.
IMPORTANT: For best performance, keep mower housing free of buibup grass and trash. Clean underside of mower housing after each use. See "CLEANING" in CUSTOMER
RESPONSIBILITIES section of this manual,
° The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed.
Also, the mulched grass will biodegrade quickly to provide nutnents for the lawn.. AfwaYs mulch with your_highest engine (blade) speed as this will provide the best recutting action of the blades,.
o Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action The best time to mow your lawn is the early aftemoon,.
At this time the grass has dried and the newly cut area will not be exposed to the direct sun,
For best results, adjust the lawn mower cutting height so that the lawn mower cuts off only the top one4hird of the grass blades, if the lawn is overgrown it wil! be necessary to raise the height Of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your Width of cut, mow slowly and raise the rear of the lawn mower one wheel adjuster setting higher than the front o Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings.
When doing a second cut, mow across or perpendicular to the first cut path.
,, Change your cutting pattern from week to week_ Mow north to south one week then change to east to west the next week.
This will help prevent matting and graining of the lawn.
Max 1/3
7
MAINTENANCESCHEDULE
SERVICE
DATES
GENERAL RECOMMENDATIONS
T-he warranty
on this
lawn mower does not cover items that have been subjected to operator abuse or ,negligence, To receive full value from :thewarranty, _operator must maintain mower
as ,instructed
in this manual.
Some adjustments will-need to be made periodically to properly maintain your unit.
All adjustments in the Service and
Adjustments section of this manual -should be checked at least once .each season_ o Once a year, replace the spark plug, clean or replace air filter element and check blade for wear.
A new spark plug and clean!new
air filter element assures proper aiP(uei mixture and helps your
engine
run better and last longer.
o Follow the maintenance schedule in this manual.
BEFORE
EACH USE
,, Check engine oil level.
- Check for loose fasteners
LUBRICATION
Keep Unit well lubricated (See "LUBRICA-
TION CHART")
\
LUBRIICATION
(_ -Wheel adjuster mounting pin
/
(_) Handle bracket
_
CHART
Engine oil
Brake spring bracket
(1__DlschaFge guard hinge pin
(_ Sray lubricant
(_) Refer to CUSTOMER RESPONSIBILITIES
':ENGINE" section_
IMPORTANT: Do not oil or grease plastic wheel bearings.
Viscous lubricants will attract dust and dirt that will shorten the life of the self lubricating bearings.
If you feel they must be lubricated, use only a d_, powdered graphite type lubricant sparingly_
8
PRODUCT SPECnFICATIONS
MODEL NUMBER
SERIAL NUMBER
DATE OF PURCHASE
HORSEPOWER:
DISPLACEMENT:
GASOLINE CAPACITY/TYPE:
917.387023
&0
11o5 CUd IN.
1.5 QUARTS
UNLEADED REGULAR
OIL TYPE (API-SF/SG/SH):
OIL CAPACITY:
SAE 30 (ABOVE 32°F)
SAE 5W.30
(BELOW 32°F)
20 OZS.
SPARK PLUG(GAP:
VALVECLEARANCE:
.030") CHAMPION RJIgL
INTAKE: .004 - _008
EXHAUST _.
:004..
,008
SOLID STATE IGNITION
AIR GAP: ,0125 IN.
BLADE BOLT TORQUE: 35-40 FT. LBS,
" The model and serial numbers will be found on a decal attached to the rear of the lawn mower housing,Record provided above both serial number and date of purchase in space
LAWN MOWER
Always observe safety rules when performing any maintenance.
TIRES
• Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.
o Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage
BLADE CARE
For best results, mower blade must be kept sharp. Replace bent qr damaged blades.
TO REMOVE BLADE o Disconnect spa_rk plug wire from spark plug and place wire where it cannot come in contact with spark plug.
o Turn lawn mower on its side. Make sure air filter and carburetor are up.
,, Use a wood block between blade and mower housing to prevent blade from turning when removing blade bolt,
,, Protect your hands with gloves and/or wrap blade with heavy cloth.
Remove blade bolt by turning counterclockwise. Use a 9/I 6" box or open-end wrench.
° Remove blade and attaching hardware
(bolt, lock washer and hardened washer).
NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly.
Replace adapter if damaged.
TO REPLACE BLADE o Position the blade adapter on the engine crankshaft.
Be sure key in adapter and crankshaft keyway are aligned,
,, Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter.
,, Be sure the trailing edge of blade (opposite sharp edge) is up toward the engine, o install the blade bolt with the rock washer and hardened washer into blade adapter and crankshaft.
° Use block of wood between blade and lawn mower housing and tighten the blade bolt, turning clockwise,
• The recommended tightening torque is 35-
40 f1,,Ibs.
IMPORTANT: Blade bolt is grade 8 heat treated_
sharpening blade- butifyoudo,besurethebladeis balanced.
Crankshaft
I SAE V_E_OD_rTY GRADES ]
Blade ..
_ keyway adapter"_..z/_ ---m--.
bolt _
\
Hardened washer
Lock washer
V'S <
Trailing "Blade edge adapter
TO SHARPEN BLADE
Care should be taken to keep the blade balanced, An unbalanced blade will cause eventual damage to lawn mower or engine.
.
The blade can be sharpened with a file or on a grinding wheel.
Do not attempt to sharpen while on the mower,
.
To check blade balance, drive a nail into a beam or wall.
Leave about one inch of
the straight nail exposed.
Place center hole of blade over the head of the nail.
If Made is balanced, it should remain in a horizontal position, If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.
GRASS CATCHER
(If purchased as an accessory) o The grass catcher may be hosed with water, but must be dry when used.
o Check your grass catcher often for damage or deterioration.
Through normal use it will wear.
If catcher needs replacing, replace only with a manufacturer approved replacement catcher.
Give the lawn mower model number when ordering.
ENGINE
LUBRICATION
Use only high quality detergent oil rated with API service classification SF, SG or
SH Select the oil's SAE viscosity grade according to your expected operating temperature.
NOTE: Although multi-viscosity oils
(5W30, 10W30 etc.) improve starting in cold weather, these multiwiscosity oils will result in increased oil consumption when
4t'_
Check your' engine oil level more frequently to avoid possible
engine
damage from running low on oil.
Change the oil after every 25 hours of operation or at least once a year if the lawn mower is not used for 25 hours in one year_
Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oi! plug securely each time you check the oil level,
TO CHANGE ENGINE OIL.
NOTE: Befo[e tipping lawn mower to drain oil, drain fuel tank by running engine until fuel tank is empty.
.
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact w]th spark plug.
o Remove engine oil cap; lay aside on a clean surface.
o Tip lawn mower on its side as shown and drain oil into a suitable container.
Container
Rock lawn mower back and forth to remove any oil trapped inside of engine, o Wipe off any spilled oil on lawn mower and on side of engine,
.
Fill engine with oil.
Fill only to the "FULL" line on the dipstick.
DO NOT OVER FILL o Replace engine oil cap,
• Reconnect spark plug wire to spark plug.
AIR FILTER
Your engine will not run properly and may be damaged by using a dirty air filter.
Replace the a!r filter every year, more often if you mow in very dust/, dirty conditions.
Do not wash air filter.
TO CHANGE AIR FILTER
, Remove the air filter by turning countercloclewise to the stop and pull away from collar.
o Remove filter from inside of cover.
° Clean the inside of the cover and the collar to remove any dirt accumulation.
Insert new filter into cover.
Put air filler cover and filter into collar aligning the tab with the slot..
Push in on cover and turn clockwise to tighten.
Clip
"rum counterto remove
Air filter
Tab 'Turn clockwise to tighten
Air filter cover
MUFFLER
Inspect and replace corroded muffler as it could create a fire hazard and!or damage.
SPARK PLUG
Change your spark plug each year to make your engine start easier and n._nbetter. Set spark plug gap at ,030 inch.
CLEANING
IMPORTAN'f_ For best performance, keep mower housing free of built-up grass and trash. Clean the underside of your mower after each use.
CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with the spark plug
• Clean the underside of your fawn mower by scraping to remove build-up of grass and trash..
° Clean engine often to keep trash from accumulating A clogged engine runs holier and shodens engine life.
o Keep finished surfaces and wheels free of all gasoline, oil,etc.
o We do not recommend using a garden hose to clean lawn mower unless the electrical system, muffler, air filter and carburetor are covered to keep water out.
Water in engine can result in shortened engine life.
CAUTION: Before performing any setvice or adjustments:
° Release control bar.
,'
°
Make sure the blade parts have completely
Disconnect piug and place where in contact spark with plug, and all moving stopped..
plug wire from spark it cannot come
TO ADJUST HANDLE
Your lawn mower handle can be raised or lowered for your mowing comfort Four
(4) positions are available: high, medium high, medium low arid low.
Handles are shipped mounted in the medium low position.
o To change from medium low to medium high position, the upper and lower handle sections will have to be turned over_
LAWN
MOWER
TO ADJUST CUTTING HEIGHT
See "TO ADJUST CUrTING HEIGHT" in the
Operation
REAR section of this manual.
DEFLECTOR
The rear deflector, attached between the rear wheels of your mower, is provided to minimize the possibility that objects will be thrown out of the rear of the mower into the operator mowing position.
If the deflector becomes damaged, it should be replaced.
DISCHARGE GUARD
The discharge guard attached to the discharge opening of your lawn mower, is provided to prevent the possibility of injury' resulting from objects being thrown out of the discharge opening into the operator mowing position, if-the discharge guard becomes damaged, it should be replaced° o Remove the cable clips.
o Remove the controls and operator presence handle.
,, Remove lower o Remove
• Disconnect handle brackets_ o Turn the handle the hairpin removed..
control the starter handle° hairpin cotters bar from the upper
rope guide from the cotters,.
the lower handle from the over and reassemble that have been
, Reassemble the starter rope guide.
,, Reassemble the controls and the operator presence control bar to the upper handle.
CAUTION: The operator presence control bar must pivot freely to permit blade/brake engagement when control bar is released,
1I
Do not overtlghten the fasteners holding the controts to the upper' handle.
<....
Shipping position
Lower handle
_,__i Medium
Squeez e remove
\
High
LOW
..,a
\\
" To change from medium low to high position only the upper handle section will have to be turned over.
o To change from medium low to tow position, only the lower handle section wil! have to be turned over.
Hairpin clip Mounting bracket
ENGINE
,CARBURETOR
.YourcaiStiretor
has, a non-adjustable fixed main_t for mixture c,ontroL Ii your engine does not operate properly due to suspected carburetor problems; take your lawn mower to an au[hofized service center for repair and adjustment.
ENGINE S_EED
The engine speed has been facto,_ set, Do not attempt to increase engine speed as it may result in personal injury. If you believe the engine is runfling too .fast or too slow_ take your lawn recover to an authorized service center for repair and adjustment.
immediately prepare your lawn mower for storage at the end of the season or if the unit will not be used for 30 days or more.
LAWN MOWER
When lawn mower is to be stored for a period of time, clean it thoroughly, remove a}t di& grease, leaves, etc. Store in a dean, dry area.
o Clean entire lawn mower (See "CLEANING" in the Customer Responsibilities section of
this manual).
o Lubricate as shown in the Customer
Responsib_ities section ofthis manual.
.
Be sure that all nuts, bolts, screws, and pins aresecuretyiastened..Inspect
moving paris for damage; breakage and wear.
Replace if necessary.
o Touch up alt rusted or chipped'paint surfaces; sand lightly before painting.
HANDLE
,you can fold your lawn mower handle for storage.
Squeeze the bottom ends oflhe lower handle toward each oU_er until the lower handle clears the handle bracket, then move handle forward_
° .Loosen upper handle mounting bolts enough to allow upper handle to be folded back
12
IMPORTANT; When folding the handle for storage or transportation, be sure to fold the handie as shown or you amy damage the control cables.
.
When setting up your handle from the storage position, the lower handle Will automatically
X x
N
Squeeze to remove
Hairpin clip
Operator presence control bar
Upper handle ._.....
Lift up
Lower handle lock into the mowing position.
Lower handle up
Mounting bracket
t
Mowing posflJor
ENGINE
FUELSYSTEM depositsfromforminginessentialfuelsystem or tankduringstorage.Also,experience indicatesthatalcoholblendedfuels(called gasoholorusingethanolor methanol)can attractmoisturewhichleadstoseparationand candamagethefuelsystemof anengine whileinstorage_ o Drainthefueltank.
o Startthe engineandletit rununtilthefuel o Neveruseengineorcarburetorcleaner productsinthefueltankor permanent damagemayoccur.
* Usefreshfuelnextseason.
NOTE: Fuelstabilizeris anacceptable the formationoffuel gumdepositsduringstorage.Addstabilizerto
gasolineinfuel
tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor, Do not drain the gas
tank and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine oil. (See "ENGINE" in the
Customer Responsibilities section of this manual).
CYLINDER
,, Remove spark plug.
• Pour one ounce (29 ml) of oil through spark plug hole into cylinder.
o Pull starter handle slowly a few times to distribute oi!.
o Replace with new spark plug.
OTHER
° Do not store gasoline from one season to another_ o Replace your gasoline can if your can starts to rusL Rust and!or dirt in your gasoline will cause problems.
o if possible, store your unit indoors and cover it to give protection from dust and dirt
° Cover your unit with a suitable protective cover that does not retain moisture, Do not use plaslic.
Plastic cannot breathe which allows condensation to form and will cause your unit to rusL
IMPORTANT: Never cover mower while engine and exhaust areas are still warm.
CAUTION: Never store the lawn mower with gasoline in the tank inside a building where fumes may reach an open flame or spark.
Allow the engine to coot before storing in any enclosure.
TROUBLESHOOTING
PROBLEM
Does not start
CHART
CAUSE
* Dirty air filter° o Out of fuel..
o Stale fuelo
Water in fuel.
o Spark plug wire is disconnected,
,, Bad spark plug.
o Loose blade or broken blade adapter.
o Control bar in released position, o Control bar defective_
CORRECTION o Clean/replace air filter
• Fill fuel tank°
. Drain tank and refill with fresh clean fuel, o Dlain fueltank and carburetor and refill tank with _resh gasoline.
,, Connect wire to plug.
o Replace spark plug.
. Tighten blade bolt or replace blade adapter, o Depress control bar to handle.
Replace control bar°
13
TROUBLESHOOTING
PROBLEM
[.o--_ of power
_oor cut _ uneven
Excessive vibration
•3tarter rope hard
:o pu!!
Grass catcher not filling (if so
...quipped)
Hard to push
CHART
CAUSE o Rear of lawn mower housing or cutting blade dragging in heavy grass.
o Cutting too much grass.
o Dirty air filter.
,, Buildup of grass, leaves, and trash under mower.
o Too much oii in engine,
,, Walking speed too fast.
o Worn, bent or loose blade,
,, Wheel heights uneven o Low engine speed o Buildup of grass, heaves and trash under mower.
o Worn, bent or loose blade,
,, Bent engine crankshaft.
o Engine flywheel brake is on when control bar is released.
° Bent engine crankshaft.
,, Blade adapter broken.
o Blade dragging in grass.
o Cutting height too low.
o Lift on blade worn off.
,, Catcher not venting air,,
,, Low engine speed.
,, Grass is too high or wheel height is too low.
o Rear of lawn mower housing or blade dragging in grass.
o Grass catcher too full.
,, Handle height position not right for you.
4 ,4
CORRECTION
-_ Setto "Higher Cut" position,
• Setto "Higher Cur' po.citiono
o Clean/replace air fitte[: o Clean underside of mower housing.
Check oil level
,_ Cut at slower walking spee&
• Replace blade. _ghten blade boll
,
o Set all wheels at same height o Set engine speed con{rol in fast position.
o Clean undelside of mower housing.
o Replace blade. "tighten blade bolt.
o Contact an authorized service center.
. Depress control bar to upper handle before pulling starter rope.
,, Contact an authorized set€ice center.
,, Replace blade adapter'.
o Move lawn mowerto cut grass or to hard surface to stalt engine.
, Raise cutting height,, o Replace blade° o Clean grass catcher, o Set engine speed control in fast position.
o Raise cutting height°
• Raise rear of lawn mower housing one (I) setting higher.
° Empty grass catcher.
,, Adjust handle height to suit.
CRAFTS AN
Garant[a
Reglas de Seguridad
Montaje
Operaci6n
Mantenimiento
Programa de Mantenimiento
Model No. 917.387023
I7 Especificaciones del Producto
I7 Servicio y Adjustes
19 Aimacenamiento
20 fdenttflcaci6n de problemas
24 Partes de repuesto
24
Orden de Partes
25
27
28
30
Vea el manual ingl6s del dueSo
Contratapa
GARANT[A LIMITADA DE DOS AltOS PARA LA SEGADORA A MOTOR CRAFTSMAN
Por dos (2) a5os, a partir de la fecha de compra, cuando esta Segadora Craftsman se mantenga, lubrlque y afine seg,Jnlos instrucciones para ]a operaci6n y el mantenimiento en el manual def due£to, Seats reparar#, gratis todo defectO en el material y fa mano de obra
Sila Segadora Craftsman se usa pare fines comerciales o de arrfendo, esta garantfa s61ose aplica por noventa (90) dias a partir de ta fecha de compra.
Esta Garantia no cubre:
,, Artfcutos que se desgastan durante el uso normal tales corno }as cuchitlas segadoras rotatorias, los adaptadores de la cuchilta, las correas, los filtros de atre y los bujt'as.
, Reparaciones necesarias debido af abuso o ala negligencia dot operadar, induy_ndose a los clgOe_ales dobladosy a ]a falta de mantenimiento def equipo segL2ntas instrucciones que se incluyen en el manual del due_o.
EL SERVICIO DE GARANT{A ES'TADISPONIBLE al devofver la segadpra a motor Craftsman al centro/ departmento de servicio Sears mas cercano en los estados unidos Esta gara.ntfase aptica solamente mientras el producto este en uso en los estados unidos..
Esta Garant[a le otorga derechos legates especfficos, y puede que tambi_n tonga otros derechos que var[an de estado a estado.
Sears, Roebuck and Co., D/817WA, Hoffman Estates, IL 60179 USA
Los estandrares de seguridad exigen la presencia del operator en los controles para reducir a un mlnlmo el rlesgo de lesionarse. Su unldad viene equipada con dichos contToles.Por ningun molJvo irate del eliminar la fi.Jnci6nde los controles que
exigen la presencia del operador.
ENTRF_.NAMIENTO: o Lea este manu_-idel operador cuidadosamente. Famitiaficese con los controles y aprenda a operar su segadora en forma adecuada. Aprenda a parer su segadora r_pidamente
,, No permita que los niiios usen su segadora,
Nunca pe[mita que los adut_os operen ta segadora sin contar con fas instrucctones adecuadas.
o Mantenga el ,_reade operaci6n despejada de genre, especialmente de niSos pequeSos y de animales dom6sticos.
o Use la segadora solamente para los fines propuestos por el fabricante y segen los e×plicaciones descritas en este manual
, No opere la segadora st se ha cai'doo daSado en cualqulera form& Stempre repare los da_os antes de usada,
No use accesor_os que no hayan sido recomendados por el fabdcante, El uso de dichos accesorios puede ser peligroso, o La cucIliIla gira cuando el motor est_ funcionando
PREPARAClON:
° Siempre revise cuidadosarnente el area que se va a segar y desp6jeIa de todas los piedras, palos, aJambres, huesos y otros objetos extra_os. Estos objetos ser_,n lanzados con la cuchilla y pueden producir lesiones graves,
SIempre use anteoJos de seguridad o protectores de ojos cuando arranque y durante ef Uempo que use la segadora.
I5
o Vfstase an forma adecuada; No o#ere la segadora sin zapatos o con sandalias mientras que e! motor estA fbncionando_
o Siegue siempre durante el dfa o con buena luz artificial
OPERACl6N:
• Mantenga sos ,o!os y su monte e.nla segadora y oR,el Area qua se estb. cortando,
.Nc_permita qu e o tros intereses to distratgan.
o No code c_sped r_ojado 6 resbaloso. Nunca corra mtentras estr_ oparando su segadora.
Siempre asegurese de mantener el equilibrio
,- man_nga f_lmango agarrado tirmarnente y camine.
.
No ponga tas manos o los pies cerca odebajo de los partes rotatoriaso Mantengase alejado de ]a abertura de descarga en todo momento, o Stempie pare el motor cuando se vaya ocuando no est, usando su segadora, o antes de atravesar las en|radas pare autos,
: los senderos, caminos y &teas cubierlas de
ri#b,
o Nuoca dirtja ta descarga dot mateflal hacia los espectadores ni permlta a nadie cerca de la segadora mientras la est6 operando.
.
Antes de limpfar, inspecciona: o de reparar [ a segadoi'a, pare ,el motor y est§ " ' completamente seguro de que la cuchilla y que todas los partes que se mue-ven se hayan detenido, Luego, desconecle el alambre de la bujfa y mantengato alejado de
{_sla para evitar el arranque por accidente,
.
No centtnOe haciendo funcionar su segado_a si le pega a un Objeto extrafio Siga el procedimiento descrito anteriormente, luego repare cualquier dafio antes de vo]ver a arrancar y de operar su segadora,
•
No cambie los ajustes del regulador o hagaque el motor ande a una velocidad excesiva. Se pueden productr dafios en e{ motor y I esiones personales,
, No opera su segadora si vibra fuera de ]o norma!. La vibraeiSn exoesiva es una fndicact6n de daho; p_,re el motor, revise en forrna segura la causa de la vibracir_n y haga las reparaciones segun sea necesario o No haga funcfonar el motor en rectntoscerrados Los gases de escape son peftgrosos.
.
Nunca corte el c6sped tirando la segadora hacla tJsted. Siegue a trav6s de la care de los pendfentes, nunca hacia arriba o hacia abajo pues puede perder el equilibrio. No siegue pendientes demasfado empinadas
Tenoa cuidado cuando ope_'e la segadora en terren0.disparejo
o cuando cambie de direccidh - mantenga Un b_en equitibri0.
' o Nunca opera la segadora sin las prolecciones .adecuadasl los planchas, el recogedor de c_sped y otros dispositivos de seguridad en su tugar, iViANTENIMIENTO Y ALMACENA_IEN-
TO:
._ Revise la cuchilla y los pemos de montaje daf motor a menudo, para asegurarse qua est_n apietados en la forma adecuad&
Revise todos los pemos, tuercas y torni/Ios a intervaJos frecuentes, pare veriflcar si esl&n apretados en forma adecuada, y asegurarseque la segadora se encuentra en condiciones de funcionarniento seguro.
• Mantenga todos los dispositivos de seguridad ea su lugar y Ifstos pare funcionar,
° Pate reductr el peligro de incendio, mantenga el motor sin cesped, hojas y grasa o aceite en exceso
Revise el recogedor de c#,sped a menudo pare vedficar si hay detetioro y desgasie y cambie las bolsas desgastadas Use solamente los IJolsas de repuesto recomendadas por e! fabficante de su segadora o qua cdmplen con los
especificaciones de _ste
o Siempre mantenga una cuchilla afilada en su segadora o Siempre permita qua el motor se enfrfe antes de guardafla en cuatquier recinto cerrado,
° Nonce guarde la segadora con combustible en el estanque dentro de un edificio endende los gases pueden alcanzar una llama expuesta o una fuente de tgnici6n, tal como el calentador de agua, la estufa de calefacci6n, ta secadora de rope, etc.
PRECAUC|ON: Siempre desconecte el atambre ,de la bujla y pbngato donde no pueda entrar en contacto con [a bujfa, pare eviler el arranque por accidente, durante la preparaci6n, el tr'ansporte, el ajuste o cuando se hacen reparaci_nes
PRECAUCI6N; Es conocido por el Estado de
California qua los gases de escape del motor de este productor contienen qufmicos los cuales a ciertos niveles, pueden ocasionar, cancer, defectos de nactmlento, y otros da[_os al sistema rep_oductlvo.
16
Estos accesorios estaban dispontbles cuando se produjo la segadora, Tambien estAn disponibles en la mayorfa de fas tiendas de Sears yen los centros de servicio. La mayorfa de las lendas
Sears tambi_n pueden ordenar partes de repuesto para usted, si [es proporciona et numero del
RENDaMtENTO
ORA
__.
DESV]ADOR
PARA SEGADORAS
DE. RECOITIS
CON DESCARGA TRASERA
\
SEGADORAS
= oo=E°o=pA=A
"fRASERA
MANTENIMIENTO DE LA SEGADORA
JUEGOS PARA LA AGOLCHADQRA
RECOREDOR
PARA
SEGADORAS
CON OESCARGA
LATERAL
ESTABILIZADORES
9S ij
ENVASES
DE GASOLINA
W
8UJiAS
SILENC|AOORES
CORREAS i
CUCHtLLAS
ADAP
TADORES
DE CUCHtLLA
........
ACEITE
DEL MOTOR
.:=:::.,
Lea estas instrucciot_es y este manual comptetamente antes de tratar de montar u operar su segadora nueva, Su seg+adora nueva ha sido montada en la fAbrica con la excepci6n de aquellas partes que se dejaron sin montar pot razones de envfo,, Todas ins partes como Ins tuercas, Ins arandelas, los pernos, etc, que son necesarias para compietar el montaje ban sido colocadas en la bolsa de partes. Para asegurarse que su segadora functone en forma segura y adecuada, todas las partes y los arlcuios de ferreterfa que se monten tienen que ser apretados seguramente, Use ins
13erramientas correctas, como sea necesario, para asegurar que se aprieten adecuadamente,
PARA REMOVER LA SEGADORA DE LA
CAJA DE CART(SN
.
Remueva las partes sueltas que se inctuyen con ta segadora.
= Corte Ins dos esquinas de los extremos de la caja de cartSn y tienda et panel del extremo piano,
Remueva todo e[ material de empaque, excepto 1_ cuSa entre el mango superior y _]
inferior, y fa cuSa que sujeta la barra de los control que exige fa presencia de1 operador
junto con el mango superior.
17
Haga rodar la segadora hacia afuera de la cain de cartSn y rev[sela cuidadosamente para verlicat si todav[a quedan partes sueltas adicionales
COMO PREPARAR SU SEGADORA
PARA DESDOBLAR EL MANGO
IMPORTANTE; Despliegue el mango con mucho cuidado para no pellzcar o daSar los cables de control
.
Levante los mangos hasta que la secciSn del mango Inferior se asegure en su lugar, en la posiciSn para segar.
.
Levante fa secciSn def mango superior has_a su lugar en et mango inferior, remueva ta cuRa protectora y apriete ambas mantfas del mango o Remueva ta cuSa de] mango que sujeta ia barra det control que exige la presencla det operador junto con el mango superior,,
° El mango de la segadora puede ajustarse seg[]n _e acomode para segar Ref{erase a
"AJUSTE DEL MANGO" en la Secci(_n de
Servicio y Ajustes de este manual
Barradecontrolqueexige{a deioperador"---.
Mangosuperior
Levantar segar
Mangoinferior/
FAMILIARICESE CON SU SEGADORA
LEA ESTE MANUAL DEL DUEllO Y LAS REGLAS DE SEGURIDAD ANTES DE oPARAR Su
SEGADORA Compare las ilusLracionescon su segadora para familiadzarse con la ubicaci6n de los diversos controfes y ajustes. Guarde este manual para referencia en el futuro.
Estos simbolos pueden apareser sobre su segadora o en la literatura proporcionada con el productoo Aprenda y comprenda sus significados.
ATTENGt_N O
• ADV'ERTENCtA
MOTOR
ENCENDJDO
MOTOR
APAGADO
RAPIDD
CordSn arrancador
LENTO ESTR.t-_IGU
LAC_H
COM.
8USTIgLF-.
ACEITE PELIGRO r-4tUARDE LAS
MANO._
Y LgS PI¢_S LEJO5
Barra de control que exige ta presencia del operador
Manitla det mango
Abrazadera de] cable
Tapa del deposito de acelte del motor con varilla indicadora de nivel
Puntaf de tope
Cable de control de fa velocidad dei motor
Tapa del deposito gasotlna
Cebador
Proteccf6n contra la descarga
Caja
Ajustador de ia rueda
(En cada rueda)
P}ace de la acolchadora
CUMPLE CON t.OS REQUISITOS DE SEGURIDAD DE [A CPSC
Las segadoras a motor; que se conducen desde ]a parte de atr#,s, rotatorias, Sears, cumplen con los est_ndares de seguddad det American Na{ional Standards insf_tutey de la U.S. Consumer Product Safety
Comm!_tono La cuchfl_ag!ra cuando el motor estA funcionando.
Bara de ocntrol que exige ta presencia del
operador - tiene que sujetarse abajo, Junto con e! mango, para hacer arrancar el motor.
Su_ltela para parar el motor.
Cebador - bombea combustible adicional desde el carburador at cillndro para uso cuando se necesita hacer arrancar un motor frio,
18
Oord6n arrancador - se usa para hacer arrancar el motor.
Ptaca de la acolchadorasituada en la abedura de la descarga y debe ser quitada cuando se convlerte la operaccton de ensadcado a descarg&
La operact6n de cualquier segadora puede hacer qua salten objetos e_raSos dentro de sus ojos, Io qua puede producir dares graves en 6stos.
Sfempre use anteojos de seguridad o protecci6n para los ojos mientras opera su segadora o cuando haga ajustes o reparaciones Recomendamos una mascara de seguridad de visi6n amplia, pare use espeJueloso anteojos de seguridad estandarle
COMO LtSAR SU SEGADORA
VELOCtDAD DEL MOTOR
La velocidad del motor se estableci6 en la f;_.qbdca
pare un rendimiento 6primo. La velocidad no se puede ajustar.
CONTROL DE ZONA DEL I'_OTOR
PRIECAUCION: [..as regulaciones federales exigen qua se instale un control par a e! motor en esta segadora para reducir a un mfnimo el riesgo de lesionarse debido al tentacle con ia cuchi{t& Per ningL)n motive trate de eliminar ta funci6n del control del operadoro La cuchilla gira cuando el motor est6 funcionando.
o Su segadora viene equipada con una barra de contrc4clue exige la presencia del operador, Io que requiere que el operador est6 detr&s de_ mango de la segadora pare haceda arrancar y operada..
PARD, AJUSTAR LA AL'TURA DE CORTE
,, Levante las medas para el corte bajo y baje las ruedas para el corte alto o Ajuste la attura de corte pare qua se acomode a sus requisites La posici6n de! medio es la major pare la mayor[a de los cespedes..
o Pare cambiar la aJturade core, empuje fa palanca del ajuslador hacia In nJeda Mueva ta r,Jedahacia arriba o hacia abajo de mode que
se acomode a sus requisites Asegurese qua todas las ruedas queden igualmente ajustadas.
ATENCI6N: El ajustador esta correctamente colocado cuando los orejas de laplaca estb.n
insertadas en el agujero del mango. Tambi6n, !os
ajustes de 9 posiciones (st equipado} pemqiten qua el mango pueda set movido entre fas orejas de la place.
PARA CONVERTtR A SEGADOFtA
DESCARGABLE
Su segadora es enviada pare usarse come acolchadora Para convertifla a una operaci6n de
Orejas de fa
Pare un corte alto, baje los ruedas p}aca 2_ i;';);, (I-'_; Mango
Para un torte bajo, levante las ruedas ensacado o de descarga:
Levante la protecd6n centre ia descarga y remueva la plancha acolchadora o Ahora la segadora se puede USErcon descnrga lateral o sete puede adjuntar el recogedor de cesped opclonal,
• Pare votver ata operaci6n de acolchamiento, simplemenle vuelva a instalar la plancha acolchadora seg0n se muestra.
PRECAUCI6N: No haga functonar la segadora sin la protecci6n centre ta descarga, et race-.
gedor de c,6soed o la plancha acotchadora, aprobados, en su tugar.
__',v _, .
Protecci6n
'.\
,;
_/
".._._L-,_" a_olchadora.
{ i'%'y
ANTES DE HACER ARRANCAR _.L
MOTOR
ACEffE
Su segadora rue enviada sin aceile en el motor.
* AsegOrese que la segadora est6 nivelada y qua el 6rea aJ_'ededordel dep6sito de aceite est_ limpia..
o Remueva la tapa del dep6sito de aceite dot motor' con la varilla indicadora de nivet y rellene haste In linea de ileno en _sta
- Use 20 ozode acei[e.. Pare el ripe y la calidad yea
"MOTOR" en la secci6n de los
"Responsabif{dades del Cliental' en este manual,.
, Vacie el aceite lentamente. No Io Ilene demaslado.
- Revise el nive] del aceite antes de coda use.
Ag_gue aceite si es necesario, Uene haste la tinea de tleno en la varilta indicadora de nivef.
,, Pare leer el nivef adecuado, apriete la tapa del dep6sito de acette del motor coda vez..
o Vuelva a instalar la tapa del dep6sito del aceite y apri6tela.
,
Camble el aceite despu6s de 25 heros de operaci6n o ur'a vez per temporada Puede necisitar cambiar el aceite m&s a menudo
cua_do los condiciones son poRerosas o sucias..
GASOUNA
°
Ltene el estanque de combustible, Use gasotina regular, sin pfomo, nueva y limpia con el mi'nimo de 87 octanes, No mezcle e!
aceite con fa gasoline..
Para asegura_ que la gasoline uttlizada sea "tresca compre estanques los cuales puedan ser utilizados durante los primeros 30 dias_
ADVERTENOIA: La e×perlencla ha Indtcado que los combustibles mezc/ados con alcohol
(conocidos come gasohot, o el use de etanol o metanol) pueden atraer ta humedad, la que conduce ata separaci6n y formaci6n de &cldos durante el almacenamlento,
La gasolina acldica puede daiiar el sistema det combustible de un motor duranle el almacenamiento, Pare evitnr
conelmotor,sedeberacierel sistemadelcombustible unperfodode30dfaso mb, defcombustiNe, s Vacleelestanque hagaarrancar
hAgalo funcionar hasta que las !fneas del combustible y el carburador queden vacfos, La pr6xima temporada use combustible nuevo,
Vea tas lnstruccfones Para El Almacenamiento
Pare evitar 6sto, rocfe el recogedor con la mangue_ade ague, regularmente, y d6jelo secarse antes de usar!o
° Mantenga la parte superior del motor, atrededor del arrancador; despejada y sin recedes de c6sped y paja. Esto ayudar_ el flujo del aire del motor y extender#, la duraci6n 6ste,
CONSEJOS PARA SEGAR Y ACOLCHAR pare mb,s informaci6n, Nunca use productos de timpieza pare et motor opara el carburador an el estanque de] combustible pues se pueden producir dai'ios permanentes
,f-r_tpa del
..J---"_z-_.
....
rellenador de
IMPORIAN1-E: Para obtener el meier rendimiento mantenga ta caja de la segadora sin acumulaci6n de cesped y basua,.Vea "LIMPIEZA" en ta seccDn
"RESPONSABILIDADES DEL CLIENTE" de este manua!.,
• La cuchifla acolchadora especial vaa vofver a
Tapa de, ..-_ t-_'t g asotina acoitecon cedar los recortes de c_sped touches veces, y los reduce en tamaSo, de mode quesi se caen en el c_sped se van a dispeser entre 6ste y no se van a notar,.Tambi_.n, el c_sped acolchado se va a deshacer r@tdamenle entregando substancias nutdtivas para el c_sped Siempre acolche con la velocidad del motor (cuchilia) m_s ella, pues as[ se obtendr,_ la meier acci6n de recorte de las cuchillas
" Pare hacer arrancar un motor fifo, empuje et cebador cinco (5) veces antes de tratarto_
Empuje f]rmemente, Este paso normalmente no es necesario cuando se hace arrancar un motor que ya ha estado tuncionando per unos cuantos minute&
• Suje|e la barra de controles que exigen la presencia del operador abajo an el mango y tire el mango del arrancador r#.pidamenle_No
permita que el cord6n arrancador se devuelva abruptamente
•Para parar et motor, suelte la barra de controles qua exigen fa presencia del operadoro
AVlSO: En dimas m&s fries puede que sea necesario repegr los pasos del cebado..En climas m#,scaturosos el cebar demasiado puede producir el ahogo y el motor no va a arrancar. Si se ahoga el motor espere unos cuantos minutes antes de tratar de hacello a[rancar y no repita los pasos det cebado,
CONSEJOS PARA SEGAR
,, Evite cedar et cc-sped cuando est_ mojado El c_sped mojado iiende a fon'nar montones e interfiere con la acciSn de acolchado, La major hera pare sega_ el cesped es temprano en fa tarde. A esa hera _ste se ha secado y el area reci_n coflada no quedar,_expuesta al sol directo.
o Pare obtener los mejores resultados, ajuste la altura del code de la segadora de mode que ¢sta corte solamente el terciosuperior de las hojas de c_sped. En el case de que el c_sped haya crecido demasiado, puede ser necesario et elevar la altura del code para [educir el esfuerzo necesado para empujar la segadora y pare evilar sobrecargar el motor, deiando montones de recedes de c_specl Para un acolchamiento muy pesado, reduzca el ancho del co_te pasando per enclma del tugar anteriorrnente cortado y siegue lentamente
•
Bajo clertas condiciones, tal come c&sped muy alto, puede ser necesado el elevar la attura del torte para reducir el esfuerzo necesario pare empujar la segadore y para evitar sobrecargar el motor, dejando montones de recortes de c_sped.
,, Para un c_)demuy pesado, reduzca el ancho del corte pasando parclalrnente per encima del lugar anteriormente cortado y siegue lehiamente.
• Sitas segadoras de descarga laterancorten en una direcci6n contraria a las man!lies del reloj, si se em-pieza en ta parle de afuera del Area que se va a cortar, se repaitir&n los recortes del c#sped en forma m&s pareja y el motor se cargar,_menos. Para evttar que los recortes caigan en los senderos, en las flores, etc., haga los primeros cortes en la direcci6n de tas manillas del reloj
o Los pores en los !ecogedores de c6sped de tela pueden llenarse con mugre y polvo con el use y los recogedores recaudar,Cnmenos c#sped, o Ciedos ttpos de cesped y sus condiciones pueden exfgir que un .4tea tenga que ser acoichade per segunda vez para esconder compielamente los recortes Cu&qdo se haga el segundo code, siegue atravesado o en brma perpendicular a la pasada del pdrner code..
- Cambie su patr6n de corte de semana a semana Siegue de norte a sur una semana y luego cambie de este a oeste ]a pr(*_xima semana. Esto evitara,que et c6sped se enrede y cambie de direccbno
Max 1/3
2O
PROGRAIVIA DE I'4ANTENIM]ENTO
£LENE LAS FECHAS A MEOIDA
QUE COMPLETE SU. SERVICIO REGULAR
Reviser si hay sujeladores sueltos
SI
El
Liraplarfinspecclonar el tecogedof de cesped (si viene equipado)
Limpiar la segaciora
GI
AI
Umplar debajo de la cuDietta de la lrans: m|si6n (segadoras con poder propulsor)
Di
O1
Reviser tas coffees y las sadas (segadoras con
Revis,_r. o/alttar!cambiar
la cuchilla
RI
AI
Table de lubricaci6n
)i_r la ba_eda/recatga_ ado[as con atra#qoe el_cltico)
Reviser et niveI del aceile
Cambiat, el aceite deI meier
Llmpiar et filtro de aife lnspeccionaf el silenctadot
RI
Limpiar o.tcambiar
fa bujit_
Cambiar el ¢ar_ucho de paget del lil#o de ai[e
I - Cambt_r m&._ a men#do cuande se oiPer_ balr_ eat! ;a pesada o en ambienfos con allas lempereluras,
2 - Oa_rservido ra4_,Ja menuU# c#ando se o_,ef8 er_cendl¢fene_ 5uciBs o polvotosas
3 - C_mbie {as _cl_iltas m&s a menudo cuando siegue en le_-Tenoafer_ose.
4 - Ca_,ga_per 48 l_orasal ttn de fa tempe_'aata
TABLA DE LUBRICAClON
RECOMENDAClONES GENERALES
La garantia de es{.asegadora no cubre los artfculos que ban estado sujetos al abuse o a la negligencia del operador: Para recibir rode el valor de la garantfa, et operador tiene que mantener la segadora segQn las instrucciones descritas en este manual
Hay algunos ajustes que se tienen que hacer en forma peri6dica para poder mantener su unidad adecuadamente.
Todos los ajustes en fa secci6n de Servicio y
Ajustes de este matiuaf tienen que ser revisados per Io menos un vez per cada temporada.
o Una vez al aSo, cambie la bujia, timpie o eatable et elemento deI fi]tro de aire y revise si la cuchilla estA desgastada Una bujfa nueva y un elemento del fiftro de aire limpto/ nuevo aseguran la mezcla de aire_combustible adecuada y ayudan a que su motor funcione meier y que dure rnas o Siga el programa de mantenimiento en este manual
ANTES DE CADA use
, Revise el ntvel del aceite del motor
• Revise si hay sujetadores sueltos..
LUBRICACION
Mantenga, fa unidad bien tubricada (vea la
"TABLA DE LUBRICACION"),
(_ Ajustador de la rueda
\
(_ Aceite del motor
(_) Puntal de resorte del freno
21
(_ Clavija de
®
®
(_ Ciavija de la montaje del
punlal de mango articulaei6n de fa protecci6n de descarge
ROCIE EL.LUBRICANTE
REFIERASE A LA SECClON DE
RESPONSABILIDADES
DEL CLIENTE EN "MOTOR"
IMPORTANTE: No aceite o engrase los redamlentos de ta rueda de plaslico, Los tubricantes viscosos atraeran polve y mugre, Io que acerlara ta duraciSn de los rodamlentos autolubricantes, Si cree que _ienenque lubdcarse,
_se sotamente un lubricante ripe grafito, polve seco, In forma moderada.
ESPECUFRCACHONES DEL
PRODUCTO
917,38 7023
D!MOD LO
UMERO DE SERIE-
r_F_CHA D
E
COMP--R-A
CABALLOS DE FUERZA:
:)ESPLAZAMIENTO:
4.0
9.05 CU. IN.
CAPACIDAD Y TIPO
DE GASOLINA:
1.5 Cuartos
REGULAR SIN PLOMO
TIPO DE ACEITE:
(AP1-SFiSGiSH)
CAPACIDAD DE ACEITE:
BUJiA (ABERTURA:
TOLERANCtA
,030")
DE VALVULA:
SAE 30 (sobre 32°F)
SAE 5W-30 (debajo 32°F)
20 oz. de capacidad
CHAMPION RJ 19L
ADMISION: ,004 -
.008
DESCARGA: .004 - .008
SENCENDIDQ DE ESTADO
SOLIDQ ABERTURA DE AIRE:
,0125
IN,
TORSION DEL PERNO
DE LA CUCHILLA: 35-40 FT, LBS,
El num_ro del nodelo y el de serie se encuentran en la calcomania adjunta ata parte trasera de la caja de fa segadora.
Debe registrar tanto el num6ro de serie come la iecha de compra y mantengalos en un ]ugar seguro para refencia en el futuro.
_EGADORA
Siempre observe ias reglas de seguridad cuando haga el manlentmiento_
LLANTAS
° Mantenga las !lantas sin gasoline, aceite o substancias quimicas para control de insectos que pueden darer la goma o Evlte los tocones, las piedras, las grietas profundas, los objetos afilados y otros peligros que pueden d&fiar a las flantas,
OUIDADO DE LA CUCHILLA sentido contrarlo en que gtran las manittas del reloj, o Remueva la cuchitta y los art[culos de ferreteria adjuntadores (el pemo, la arandela de seguridad y la arandela endurecida),
AVlSO: Remueva el adaptador de la cuchilta y revise el cubo interior de la ranura del adaptador de la cuchilla, La ranura tiene que estar en buenas condiciones para qua funcione en forma adecuada,
Cambie et adaptador si est_ dafiado,
PAPA CAMBIAR LA CUCHILLA
Para obtener los mejores resultados, la cuchitla de la segadora flene que mantenerse afilada. Cambfe
Ia cuchilla dobladao da_ada_
PARA REMOVER LA CUCHILLA o Desconecte el alambre de ta buj[a y p6ngab en donde no pueda entrar en contacto con 6sta_ o Haga descansar la segadora en su lado.
Asegt]rese que el filtro de aire y que el carburador queden mirando hacia arriba,
• Use un bloque de madere entre la cuchifla y ta caja de ta segadora pare evitar que la cuchflla gire cuando se le quite el pemo..
Proteja.sus manos con guantes y/o envuelva ta cuchtlla con una iela gruesa.
.
Remueva el pemo de la cuchilla glr&ndolo en el
Ponga el adaptador de la cuchilla en el ctgue_a!
del motor, Asegerese que la ranura del adaptador y que el chavetero del ciguefial est_n alineados.
•
Ponga la cuchilla en el adaptador de _sta , alineando !os dos (2) agujeros en ia cuchilla con tas satientes'elevadas en el adaptador_
• AsegOrese de que et borde de salida de la cuchilla (opueslo al boide afilado) est_ hacia ardba hacia el motor.
•
lnstale et pemo de la cuchiila con la arandeta de seguridad y la arandeta endurecida en el adaptador de la cuchilla y el dgueSal,
• Use up,bloque de madera entre la cuchiila y la caja de la segadora y apriete el pemo de la cuchilla glrAndolo en e! sentido en que giran las menillas del reloj.
22
° La torsi6n pare aprelar recomendada es de 35 -
40 pies libra3°
IMPORTANTE; EI perno de la cuchitla es clase
8 tratado a cator.
AVISO: No recomendamos el afilar la cuchiiiapero si 1ohace, asegQrese de que quede balanceada
PARAAFILAR LA CUCHtLLA
Se tiene que toner cuidado de manteneda batanceada. Una cuchilta que no esL4balanceada va a producir eventualmente daflo en la segad0ra o en el motor..
La cuchilla puede afllarse con una lima o en una rueda recfificadora. No trate de afilafla mientras se encuentra en ia segadora.
Para revlsar etbalance de la cuclqilla, clav,3[.in
davo en una riga o en ta pared.. Deje atrededor de una puigada de un clavo recto expuesto.
Ponga et aguiero centraJde la cuchiUasobre la cabeza def ctavo. Si ]a cuchiita estb,balanceada debe pen'nanecer en la posicbn horizontal. Si cualquiera de los ex_remos de ta cuchitla se mueve hacia abajo, afife el extremo pesado haste que 6sta quede baJanceada.
Adaptador de la cuchilla
Ranura.___%
Perno Cuchilla _4-_---:i_ / l _"'" .... '_,
Arandefa de seguridad
Chavetero del ciguefiat
I ! .._XL __Ll_
._C_guenal
_)) Adaptador
\ _ "'%_." --<_:
"x
",
Arandela
_-de
Borde de la cuchitla salida endurecida
CALIE)ADE$
OE VI._GOSIDi_D
DE SAE -_---I
l_l_,'a ¢._B_o D__c_tE I
AVtSO: A pesar de que los aceites de multlvtscosidad (5W30, 10W30, etc.) mejoran et arranque en clima frio; estos aceites de multMscosidad van ha aumentar el consumo de aceite cuando se usan en ternperaturas sobre
32 ° F. Revise et nlvel del aceite del motor m6,s a menudo, pare evitar un posible daSo en el motor, debido a qua no tiene suficiente aceite.
Cambia al aceite despu6s de 25.bores de operaci6n o por 1omenos una vez al afio si la segadora se utilize menos 25 bores et aho,
Revise el nive/dal aceite def c6rte_ antes de arrancar el motor y de_pu_s de cada cinco (5) horas de uso continuado. Apriete el tap6n del aceite en forma segura cada vez que revise el ntvel del acette.
PARA CAMBIAR EL ACEITE DEL MOTOR
AVISO: Antes de inclinar la segadora pare drenar el aceite, (:irenee! tar_quede combuslJbie haciendo cotter el motor has_ que el tanque est6 vacio.
, Desconecte et alambre de ta buila y p6ngalo de modo que no pueda entrar an contacto con 6sta.
• Remueva ta _apadel rJep6sitode1aceite; d6jela a un lado en una superficie limpia..
o Incline la segadora y hAga]a descansar en su fado y drone el aceite en un envase adecuado..
Mueva ta segadora de a_-_s pare adelante pare remover todo el aceite que se haya quedado a_apado dent_odot motor..
o Limpie todo el aceile derrarnado en la segadora y en e! lado det motor.
, Uene e!motor con aceite. Ll6nelo solamente hasta la linea de !leno (FULL) en la varilta indlcadora de nlvel. NO LO LLENE
DEMASIADO.
- Vuelva a poner la tapa en el dep6sito del aceite.
.
Vuelva a conectar el atambre de la buj[a a 6sta.
RECOGEDOR DE CI_SPED
(St comprado como un accesorto) o Ei recogedor de c6sped puede ser rocfado con el agua de la manguera pero ttene que ester seco cuando se vaya a usar_
, Revise su recogedor de c6sped a menudo para verit]ear si est& de, ado o deteriorado_ Se va a desgastar con el uso normal Si se necesita cambiar el recogedor, c&mbielo solamente pot uno que sea aprobado pot el fabficante D6 et n_mero del modefo de la segadora cuando to ordene.
FtLTRO DE AIREE
_OTOR
LUBRlCACiON
Use sotamente aceite de detergente de alta calidad cfasificado con la elastficaci6n SF, SG o
SH de servicto APL Selecoione Ia calidad de viscosidad SAE segQn su temperature de operacl6n esperada.
23
Su motor no tuncionar& en forma adecuada y puede sufrir dafios st se usa un filtro de aire sucio.
Cambie el filtro de aJrecada afio, y m_,sa menudo si siega en condioiones muy polvorosas o suctas
No lave et _iJtrode aire.
PARACAMBIARELFILTRODEAIRE o Remueva
filtrode sire gir&ndolo en el sentido cont[ario en que giran las maniltas det re]oj, hasta el tope, y retfrelo del collar_.
', Remueva et filtro de la parle interior de ta cubierta,
• Limpie la parte interior de la cubierta y el collar para remover toda acumulaci6n de mugre
• lnserte el filtronuevo en la cublerta.
• Ponga la cubierta del filtro de aire dentro det collar alineando la oreja con la ranur& o Empuje la cubierta hacia adentro y gireta en el sentido de las las manillas del reloj para apretarla
Collar Abrazadera
Ranur_
Gire en et sentido contrario I las maniflas del reloj para remover
Fittro de aire
Cubierta del filtro de sire
Gire en el sentido de las maniltas del reloj pars apretar
SILENCiADOR inspeccione y cambie el silenciador siestA corroido pues producir un peligro de incendio y/o dafio.
BUJIA
Cambie su bujfa cads aSo para hacer que su motor arranque mAs fb,cilmente y funcione mejor: Ajuste ta abertu[a de la bujfa en 0,030 putgada
LIMPIEZA
IMPORTANTE; P.araobtener el mejor rendimiento, mantenga la caja de la segadora sin acumutaci6n de cesped y basura Limpie la parte de abajo de su segadora despues de cads uso,
PRECAUCION: Desconecte el alambre de la bujfa y pSngalo en donde no pueda entrar en contacto con _sta..
• Limpie la parte inferior de su segadora rasp#,ndola pars remover la acumulaci6n de c#sped y basura, o Limpie el motor a menudo pars evitar que se acumute ta basut"a_Un motor tapado funciona m#_scaliente y se acorta su duraci6n.
, Mantenga tas superficies pulidas y las ruedas sin gasolina, aceite, etc.
o No recomendamos el uso de una manguera de jardfn pars limpiar la segadora a menos que el sistema ef_ctrico, el sitenciador, el filtro de aire y el carburador est_n tapados pars evitar que les entre el agua El agua en el motor puede acorlar fa duraci6n de _ste,,
SEGADORA o Remueva las abrazaderas del cable,.
PARA AJUSTAR LA ALTURA DE: CORTE
Vea "PARAAJUSTAR LAALTURA DE CORTE" en
• Remueva los controJes y la barra de contro]es que exigen la presencia del operador de! mango superior,.
ta secci6n de OperaciSn de este manual,
DESVlADOR TRASERO
.
o Remueva las clavljas de horquilfa.
Desconecte el mango inferior de los puntales
Se proporciona un desviador trasero, adjunto entre las ruedas traseras de su segadora, pars reducir a del rnango_
De vuetta el mango y vue]va a montar las ctavijas de horqui!la que se hab[an removido.
un m[nimo ]a posibitidad que objetos sean lanzados hacla afuera de la parte trasera de la segadora, en la posici6n en donde se encuentra el operador, Si se da_a el desviador debe cambiarse..
.
Dirija el(los) cabte(s) por debajo de la varilla transversal de ta palanca inferior y vuelva a montar los controles y ]a barra de controles que exigen la presencia del operador en el
PROTECCION CONTRA LA DESOARGA
Se proporciona una protecciSn contra fa descarga, adjunta a la abertura de descarga de su segadora, pars evitar la posibitidad que objetos sean Ianzados hacia afuera de la abertura de descarga, en ta posid6n en donde se encuentra el operador, Si se mango superior.
PRECAUCION; La barfs de controles que exigen la presencia del operador tlene que pivotear libremente pars permitir et enganche de la cuchil]aJfreno cuando se suelta la barra de dafia la protecci6n contra fa descarga debe cambiarse control.. No apriete demasiado los sujetadores que sujetan a los controles al mango superior.
PARA AJUSTAR EL MANGO
Se puede ievantar o bajar el mango de su segadora segun le quede c6modo. Hay cuatro
(4) posiciones disponibles: sits, mediana alta, mediana baja, baJa. Los mangos se envlan montados en la posict6n mediana baja.
,, Para camblar de la poslciSn medtana baiaa medians alta, la secciSn superior y la inferior del mango tendr&n que darse vue[tao
24
.
P'ara cambiar de la posici6n de medtana baja a alta solamente se tendrA que dar vuelta la secci6n del mango superior.
.Para
cambiar de la poslcl6n medians baJa a baja, solamente se tendr& que dar vuelta la secci6n del mango inferior.
Poslci6n de env{o
Mediana baja
Alta
Meniana alia
"X
.1
Mango inferior
Apdete para remover
Puntai de!
mango
Abrazadera de horqui[a
MOTOR
:CARBURADOR
Su aarburaddrtierte un chorro principal fijq no
.ajustable p_irac_ntro]ar l& mezcla, si su mdtor no est& fl.Jncioriandoen fOrm_ adecuada debido a problemas que se sospecha, vlenen del carburador,
.. ]levesu segadora a un centroldeparlamento de sewicio autor",zadopara repamfla y/o ajustarla.
VELOCIDAD DEL MOTOR
La velocldad del motor ha sido ajustada en la f&brica, No trate de aumentar la velocidad del motor pues se pueden producir lesiones personales, Si ' cree que el motor est_ funcionando demastado r,_pidoo demasiado lento, Ileve su segadora a un centro/departamento de servicio autorizado para
repararlao ajustafla, tn_ediatamente prepare su segadora para el almacenamiento al final de cada temporada o si la unidad no se va a usar por 30 d[as o re&s.
SEGADORA
Cuando se va a guardar la segadora pot cierto per[odo de tiempo, lfmpiela culdadosamente, remueva toda la mugre, ta grasa, tas hojas, etc.
Gu&rdela en un Area {impia y seca.
Limpie toda la segadora (Vea "L1MPIEZA" en la seccl6n de Responsabilidades det Cliente de este manual).
Lubrfqueta seg6r} se muestra en la seccl6n de Responsabilidades deI Cliente de este manual.
.
.
AsegQrese de que todas las tuercas y clavijas y todos los pemos y tornillos est_n apretados
en foma seguTa, lnspecclone las partes que se mueven para verificar si estf_n daSadas,
, quebradas o.desgastadas.
CAmbtelas si es necesario.
.
Retoque todas las superficies que est6n oxtdadas o con la pintura picada; use una lija antes de pintar_
MANGO
;; Sue[te los pernos de monta]e det mango superior Io suficiente como para pe[mitir que e! mango superior se pueda dobiar hacia atr_,s.
I!VIPORTANTE- Cuando doble el mango para el almacenamiento o el transoprte, asegurese que io doble segun se muesba o puede dafiar los cables de control o Cuando prepare sus mangos a pattir de la posici6n de almacenamiento, el mango inferior autom_Licamente se asegurar_, en la posici6n para segar.
\
Apriete para remover
Mango inferior
Abrazadera horquila de
/
Puntal del
/
mango
Puede dobiar el mango de su segadora para almacenafla..
o Apdete los extremos infedores del mango inferior entre sf hasta que el mango inferior quede separado del pun_al del mango, luego mu_va]o hacta adetante.
25
Barra de control que exlge la presenc/a det operador
Mango superior
Levantar
Posici6n para segar i 2
Mango inferior
f JIOTOR
SISTEMA DE COMBUSTIBLE
IMPORTANTE: Es importante evitar que se formen deposilos de goma en partes fundamen!_ales del sistema de combustible tales como is carburador, el filtro dot combustible, la manguera del combustible oen el setanque durante el almacenamlento.
La experiencta tambien Indica que los combustibles mezclados con alcohol (conocido como gasohol o que tienen ethanol o metanol) pueden atraer humedad, Io que conduce ala separacl6n y ala formaci6n de acidos durante el almacenamiento La gasoline _cidica puede da_iar el sistema de conbustibte de un motor durante el periodo de almacenamiento..
o Drene el estanque de combustible.
• Haga arrancar el motor y dejelo funcionar haste que las l[neas de1 combustible y et carbu_ador est6n vacfos,,
o Nunca uselos productos para limpieza del carburador odei motor en el estanque de combustible pues se pueden produclr daRos permanentes.
Use combustible nuevo la pr6xfma temporada.
AVISO; E! estabilizador de combustible es una alternattva aceptable pare reducir a un mfnlmo ta formaci6n de dep6sltos de goma en et combustible durante e! perlodo de almacenamiento.
Agregue estabtllzador a la gasotina an et estanque de combustible o en el envase pare el almacenamiento.
Siempre siga
la proporci6n de mezcfa que se encuentra en el envase def estabilizador Haga funcionar e! motor por lo menos 10 minutos despu_s de agregar el estabilizador, pare permltir que este llegue al carburador, No drone la gaso]ina del estanque de gasoline y el carburador si se est& usando estabifizador de combustible,
ACEITE DEL MOTOR
Drone el aceite (con el motor caliente) y c&mbiefo con aceite de motor limplo.. (Yea
"MOTOR" en fa seccidn de Responsabilidades del Otiente de este manual.)
CILtNDRO
Remueva ta bu}[a, o Vacfe una onza (29 ml) de acelte a tray,s dot agujero de ta bujfa en el cilindro.
Tire la manilfa de arranque lentamente unas cuantas veces pare distribuir e! aceite
.
Vuelva a montar la nueva bujia
OTROS
o No guarde la gasotlna de una temporada ala otra_
.
Camb/e el envase de la gasofina si se empieza a oxidar. La oxidaci6n y/o la mugre en su gasolina producir&n problemas..
° Si es posible, guarde su unidad en un recinto cerrado y cubrala pare protegerla contra el potvo y la mugre.
° Cubra su unidad con un forro protector
adecuado que no r_tenga la humedad. No use pt_stico. El p!&stico no puede respirar, 1o que permite ta formaci6n de condensact6n, to que producir& la oxidact6n de su untdad.
IMPORTANTE: Nunca cubra la segadora mientras il motor y las areas de escape todavia estan calientes,
PRECAUCION: Nunca atmacene la segadora con gasolina en el estanque dentro de un edificio en donde los gases pueden alcanzar una llama expuesta ouna chispa, Perm[ta que se enfrie el motor antes de almacenarla en alg0n recinto cerrado, i 26
IDENTIFICAClONbE PROBLF-.i_ilAS
_ROBLEMA
NOarranca
Falta de fuerza
CAUSA
• Filtro de aire sucio,
Sin combustible..
o Combustible rancio
• Agua en el combusttble_ oAlambre de la bujfa desconectado,
, Bujfa real&
• Cuchilta suelta o adaptador de la cuchilta quebradoo o Barra de control en _a posici6n suelta
• Barra de control defectuos&
• Parte trasera de la cajacuchilla de la segadora arrastr&ndose en el o_sped pesado.
° Est& cortando mucho c_spe&
° Filtro de aire sucio.
° Acumulaci6n de cesped, hojas y basura debajo de ta sagadora.
° Demasiado aceite en el motor.
CORREOCiON
- Limpie/cambie el fittro de atre.
,, Uene et estanque de combustible.
,, Drene el estanque y vuelva a
Ilenar_o con combustible ]impio y nuevo o Drene ei estanque de combustible y
el carburador y vuetva a lianas"et estanque con gasollna nueva.
Conecte ei alambre a la bujta.
o Cambie la bujfa.
° Apriete el pemo de la cuchtlla o cambie el adaptador de la cuchilla.
° Presione la ba[ra de control hacta el mango.
o Cambte la barra de control.
AjusLe a la posici6n de "Corte m_.s
alto,"
Ajuste a la posici6n de "Code mAs altO." o Limpiefcambie la segadora,
• Corte a una velocidad de recorrido m#,s tenta, el fiitro de aire.,
° Limple la parte inledor de la caja de
• Revise el nivel del aceite.
27
PROBLEMA
Vlafcode+_Jisparejo
Vibraci6n excesiva
Cord6n arrancador dificil de tirar
.
CAUSA o
Cuchllta desgastada, doblada o suefta,
Altura de las ruedas dispareja+
Q
Velocidad de! motor lenta.
o Acumulaci6n de c#sped, hojas o basura debajo de la segador a_ o Cuchilla desgastada, dobtada o suelta,
.
Cigue5al dot motordoblado+
El freno del volante del motor est& aplicado cuando se suefta ta barra de control.
+ CigueSat del motor dobtado,
° Adaptador de ta cuchilla quebrado
.
La cuchitla se arrastra en el c_sped,
Recogedor de c6sped no se tlena (st viene equipado)
• Attura de corte demasiado baia.
.
Levantamiento de la cuchi!la
desgastado+
° Recogedor sin venttlacl6n de aire.
+ Velocidad del motor lenta.
Diffctt de empujar o
El c6sped est& demasiado alto o la altura de la rueda demasiado baja+
Parte trasera de la caja/cuchilta de la segadora arrastrAndose en el c_sped+
Recogedor de c@sped dema+ siado llano+
Posici6n de la aftura del mango no adecuada para usted
Cambie la cuchilla+ Apriete el perno de la cuchilta,
Ajuste todas las ruedas a la misma altura,
P6ngase en contacto con su centro de servicio autorizado m_.s cercano.,
Limpie la parte inferior de ]a caja de la segadora
Cambie la cucllilla. Apriete el perno de la cuchilla
P6ngase en contacto con su centro de servicio autorizado m_is cercano,
Presione la barra de control hacia el mango superior antes de tirar el cotd6n arrancador.
P6ngase en contacto con su centro de servicio autorizado m#,s cercano,
Cambie el adaplador de ta cuchilla.
Mueva la segadora a un lugar en donde el c_sped ha sido cortado o a una superficie firme para hacer arrancar el motor.
Eleve la aftura de corte
Cambie la cuchillas+
Limpie et recogedor de c6sped.
Ajuste el control de la velocidad del motor a la poslci6n r&pida
Eleve la attura de corte.
Eleve la parte trasera de la caja de la segadora (I) un lugar rn@salto,
Vade el recogedor de c_.sped.
Ajuste fa altura del mango de modo qua le acomode.
28
29
o
25
52
ROTARY LAWN MOWER--MODEL NO.917.387023
14
28
38
17
23
24
\
25
31
23
4O
ROTARY LAWN MOWER-
-MODEL
NO. 917.387023
KEY
NO,
PART
NO.
DESCRIPTION
26
27
28
29
30
31
32
35
8
9
10 t 1
12
13 t4
15
3
4
5
6 t
2
86902
145646X479
850733X004
750097
STD541425
156577
151517
63601
136376 t 4Q543
701313
87584X004
15t665X479
151667X479
17
!8
20
2!
750085X007
146630
87877
700331X004
22
23
145935X004
62335
24 o 142748
25 146248
83923
53998
77400
850999
48403
701706X479
751592
851084
Control Bar
Upper Handle
Up-Slop Bracket
Hex Wsh.
}-lead Screw #10-24 x t12
Locknut 114-20
Engine Zone Control Cabie
Cal31e Clip
Nylon Locknut
Handle Knob
Rear Skirt
Engine Spacer
Skirt Bracket
Handle Bracket Assembly (Right)
Handle Bracket Assembly (Left)
Wheei Adiusting Bracket
Spacer
Selector Knob
Selector Spring
Axle Arm Assembly
Belleville Washer
Shoulder Bolt
Wheel and Tire AssembIy
Hex Flange Locknut 3/8-16
Fiat Washer
Hubcap
Hex Head Se]f4applng Screw 3/8-16 × 1-1/8
Lawn Mower Housing Kit (Incl.
Rel, #31, 43'}
Front Baffle
Locknut 318-16
Hex Head Machine Screw
3/8-24
x t-3/8
(Gr. 8}
KEY
NO.
PART
NO.
DESCRIPTION
42
43
44
46
47
48
49
50
51
52
56
36
37
38
39
40
4t
57
- -
- -
- -
- -
850263
851074
145108
850977
150078
88272X479
88271 X479
85463
51793
147286
87589
87593
750149
157081X479
131959
103672X
......
751772X479
87576X479
152095
161303
128415
Hellcat Lockwasher 3/8
Hardened Washer
20" Mulching 8tade
Blade Adapter
Self Tapping Screw 5/t6-t8 x 3/4
Handle Support Bracket (Right)
Handle Support 8rackel (Left]
Danger Decal
Hairpin Cotter
Hinge Roa
Torsion Spnng
Housing Bracket Assembly
Discharge Guard
Lower Handle
Handle Bott
Rope Guide
Engine - (See Breakdown) Craftsman
Model I43.974036
Muicher Plate
Rear Baffle (Not Shown)
Dec:a(-EZ.
Owner's Manuai (EnglishtSpantsh)
Pop Rivet .I56 x .415 (Not shoran}
Available accessor{es not included with lawn mower:
71 33072 Grass Catcher
7__33823
ZJ..33500
"/'1.._.33300
Z.I_I33723
7.1 33316
Gas Can (2.5 gal.}
Fuel Stabilizer
SAE 30W
High Wheel
Mower
Oil (20 oz.)
Cover
Kit
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143,9/'4036
26t
4OO
195
32
CRAFTSMAN4-CYCLE
ENGINE • MODEL NUMBER 143,974036
REF
NO.
PART
NOo DESCRIPTION
REF PART
NO.
NO.
DESCRIPTION
36470A
2 26727
6 337,34
7 36557 t 2A 36558 t2B 34695
'-
14 28277
15 30589
16 32651
17 31335
I8 . 651018 ....
19 36281
20 32600
30 34460A
40 34514
40 34515 -
40 34516
41 ; . 325388.
.41
3254-88.,.
•
'¢i."
41 32549B
52
69
70
72
42 28986
42 28987
42 28988
43 20381,
45"
309638:
46
48
50
32610A
27241
36726
299t4
35261 "
3565IE
36083
75; 262q8
80 30574A
8I
-30590A
82 30591
83 305QSA
86 650488
69 611004
9Q 611112
92 650815
93 650816 t00 34443A
101 610118
103 651007
110 34961
1!9
t20
36437
36474
"
I25
125
36471
36472
Cylihder .....
(Incl.. 2,7.20, I25.169';172_ 174}
Dowel Pin
Breather Element
Breather &ss'yi(tnct. 5 & t2A).
Breather Cover & Tube (lncl. t28)
Breather Tube Elbow
Washer
Goveroor R0d:(Incl t4)
Governor Lever
Gqvem0r Lever Clamp.
Screwr Tot× :Tq 5, 8:32- x I9t64.!'
Extension Spring
Oil. Seal
Crankshaft
Piston, Pin & Ring set (Std.)
Piston, Pin & Ring Se_ (010" OSi
Piston, Pin & Ring Set {.020" OS)
Piston & Pin Ass[y (Std) (Ih.el,.43)
Piston & Pin Ass'y.
.(.010" OS) (lncL 43}
Piston & Pin Ass'y,
..........
(.020" OS) (lncL 43). :
#itng Set (Std,) ..
Ring Set (010""0S)
Ring Set (.020" OS)
_'
: '"
Piston Pin Retaining Ring
ConnecllngRod Ass'y (IncL 46)
Connecling Rod Bolt
Valve Lifter
Camshalt (RCR)
Oil Pump. Ass'y
Mounling Flange Gasket
Mounting F,ange {lnc172 lhru 83)
Oi1Drain Ptug
:Oil Seal :',..
" Governor Sha[_ " "
Washer -: . ""
Governor Gear Ass'y (fncL81)
Governor Spool
Screw, 1t4-20 x 1-114"
Flywheel Key
E ywlleel
Belteville Washe_;
Flywheel Nut
Solid State Ignition
Sparrk Plug Cover
Screw, Torx T..15, 10-24 x 15,ti6"
Ground Wire
Cylinde# Head Gaskel
Cylinder' Head
Exhaust Valve (Std_) ({ncl. 151)
Exhaust Valve
.:_
:,.,'
'
169 27234A _
172 32755
174 30200
I78 29752 valve Cover Gasket
Valve Cover
Screw, t0-24 x 9/16"
Nut & Lock Washer, t/4-28
!82
184
I85
620I,
26756
36544
"
Screw, t/4-28 x 7/81'
Carburetor To Intake Pipe Gasket
_ntake Pipe
Governor Link
,186
,189
_,191
32653
650839
36559 -_
195 610973
.207-
34336
Screw, 1/4:20 x 3/8"
SE, Brake Bracket (Incl. 195)
Terminal
Throttle Link
2t6 33086 R P.M. Adjusting Lever
223 650451.
224 34690A _'
. Screw;, 114:20 x t"
Intake Pipe Gasket
238 650932
239 34338 "
24I 35797
Screw, 10-32 X 49164"
Air. C_eaner Gasket
Atr Cleaner CoIlar
AIrCleaner Filter
. 245 ,, 35066
250 35065
260
261
36915
30200
Air Cleaner Cover
Blower Housing
Screw, 10-24.x 9/I6"
Screw, 1f4-20 x _1f2" 262
275
277
650831
36473
650988
Muffler (incl, 277)
Screw, 1-/4-20× 2-5/i6"
Starter Cup 285 35000A
287 650926
290 30705
Screw, 8-32 x 21/64"
- Fuel Une '
292 26460
298 28763
Fuel Line Clamp
Sdrew, 10-32 X 35164"
Fuel Tank gncL 292 & 301) 300 36916
301 36246
305 35647
Fuel Cap
Oil Fill Tube
3436 36£96 *
307 35499
3Q9
.650562
"3t0 35648 _
313.
370A
34080
36261
370C 36861
370K 36695
380' 632744
390 590694
400 36475
"O"-Ring
"O"-Rtng
' Screw, 10.32 x !/2 _
Dipstick
Spacer .. •
Lubrication Decal
Primer Decal
Starter Deca_
Carburetor (tnol, 184)
Rewind Starter ..
Gasket Set (include items marked
4t6 36085
,)
Spark Arrestor Kit
.(incl..417)(Optional)
417
900
650760
900 _
Screw, 8-32 x 3/8" {Optional)
Replacement Engine NONE
Replacement S/B 750674A, order from 71-999
RPM High 2900 to 3200
126 29314B t26 29315C
130 6021A
135 25395
150 35991 t51 31673
(1t32',O8) (IncL.151)
.
Intake Valve (Std.) (lncL I5:f)
Intake Valve (1/32" OS) (fnCt I5t)
Screw; 5116-18 x I-t/2"
•Resistor Spark Plug (RJ t 9LM)
Valve Spdng
Valve Spring Cap
(NOTE: This engine could have been built with
590737 stader Refer to the design of lhe rope pulley strength ribs lot part identification, individual starter parts dO not interchange)
NOTE: All component dimensions given in U.S,. inches
1 inch = 25.4 mm
33
CRAFTSMAN 4-CYCLE ENGINE
6¸
ILii
t
MODEL NUMBER143,974036
REF
NO,
PART
NO.
26
29
30
31
35
36
6
I6
7
25
27
4
5
1
2
37
4O
44
48
631615
631767
631184
631183
632504
650506
631776
631867
631024
32019
631028
631021
631022
36045
632745
632547
632746
27110
631027
632744
DESCRIPTION
Throttle Shaft & Levar Assembly
Throttle Return Spring
Dust Seal Washer
Dust Seal (Throttle)
Throffle Shutter
Shutter Screw
Fuel Fitting
Float Bowl
Float Shaft
Float
Float Bowl "O" Ring
Inter Needle, Seat, &CItp (IncL 3!)
Spring Cllp
Primer Butb/Retainer Ring
Main Nozzle Tube
"O" Ring, Main Nozzle Tube
High Speed
Bo_
Nut
Bowl Nut Washer
Welch Plug, Atmospheric Vent
Carburetor
(tncL 184 of Engine Parts List)
34
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER143,974036
="1 !
REF PART
NO, NO, DESCRIPTION
5 590697
6 590698
1!
7 590699
8 590700
590695
I2
I3
1 590599A Spring Pin (Inct 4)
2 590600 Washer
3 590696 Retainer
4 590601 Washer
590535
590701
590694
Brake Spdng
Starter Dog
Dog Spring
Pulley & Rewind Spring Ass'y.
Starter Housing Ass'y.
(40 degree grommet)
Starter Rope ( 98" X 9/64" dia )
Starter Handle
Recoil Starter
.q.£
REF
NOt2 t3
14
PART
NO,, DESCRIPTION
690740
5906 t 6
Retainer
Starter Dog
590617 Dog Spring
5906t8A Pulley & Rewind Spring Ass'y
590687A Starter Housing Ass'y
590535
(40 degree g_ommet)
Starter Rope
590701
(Leng_,h98" x 9/64" dta,)
Starter Handte
590741
590737
Locking Tab
Rewind Starter
For 1he iepair or replacement parts you need deliverg,d directly to your home
Call 7 am - 7 pro, 7 days a week
1-800:..366-PART
(1-800-366-7278)
Para ordenar piezas con entrega a domicili0 .- 1-800-659-7084 i
For" in-h.0,use major brand repair service
Call 24 hours a day, 7 days a week
l o80 ;4..REPAIR
(I-800-4_3:7274)
Para pedi_- servicio de reparacidn a domicilio - 1-800-676-5811 f
For the focation of a Sears Parts and
Repair Center in your area
Call 24 hours a day, 7 days a week
1-800-488..1222
For' inf6r:niation on purchasing a Sears
Maintenance Agreement or to inquire about an existing Agreement
Call 9 am - 5 pro, Monday-Saturday
1-.800 .827°6655
When requesting service or ordering parts, airways provide the following informat!£_
• Product T.£pe o Part Number
° Model N'ember ° Part Description
161303 07.,15o97 REV,1 VB
Amertcas
Repacr .,.qpeclailsts
Printed in U,S,A.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project