advertisement
Quick Setup Guide
Self-Propelled Mower
Models
SPXV2270HW
NSPXV2270HW
Questions?
Do not return to the store. We can help.
Call Customer Service Toll-Free
1-800-317-7833
Or visit our website
www.snapper.com
4
Add oil and fuel
• Move the mower outside to a flat, level surface.
B
1
Unpack the mower
• Cut all four corners of the box from top to bottom.
Starter Rope
Handle
Fuel Fill Cap
Mulching
Cover
Cutting Height
Adjust Lever
(at each wheel)
Overview
Items that you will need
Utility Knife
Unleaded Fuel (minimum 87 octane)
Items Included
FreshStart ® Fuel
Preserver Cartridge
• Remove all packing materials from the mower.
A
• Locate and identify the items included with the mower.
A
Figure 3
B
IMPORTANT Mower is shipped without oil in engine.
Failure to add oil before starting engine will result in
engine damage.
Raise the handle assembly
B
• Remove the fuel fill cap (B). Following the three-step instructions on
the FreshStart ® card, snap the fuel preserver cartridge into the bottom
of the fuel fill cap.
DANGER
Fuel stabilizer is a hazardous chemical.
Oil Fill and
Dipstick
2
• Loosen, but do not remove, the knobs (A, Figure 1)
on both sides of the upper handle.
5
Final preparation
• Move the cutting height adjust levers (A, Figure 4) to the desired
cutting height.
IF SWALLOWED, call a physician immediately.
Fuel stabilizer contains:
2,6-di-tert-butylphenol (128-39-2) and aliphatic petroleum distillate (64742-47-8).
Blade
Control (2)
Drive
Control (2)
• Unfold the upper handle so that it is aligned with the
lower handle, and tighten the upper knobs.
• Remove the handle knobs, washers and carriage bolts
from the lower handle (B).
• Raise the lower handle, aligning it with one of the
three sets of holes in the handle bracket. (Most users
will prefer the middle position). Replace the hardware,
tightening securely.
3
Figure 1
Set Up the starter rope handle
C
Not
• Squeeze the blade control (A, Figure 2) against the
drive control (B). NOTE: The blade control and drive
control can be operated from either side.
D
A
B
for
• Add clean, fresh, UNLEADED fuel with a minimum of 87 octane,
leaving one inch of space from the top of the tank for fuel expansion.
NOTE: Fuel blends containing more than 10% ethanol are not
recommended.
IMPORTANT Fuel tank holds less than 1/2 gallon.
IMPORTANT DO NOT mix oil with fuel.
IMPORTANT DO NOT use E85 fuel.
• Replace the fuel fill cap, and wipe up any spills.
• Set the mower to mulch, bag, or discharge. (See 3-in-1 instructions
below.)
A
Operate this product ONLY outdoors.
Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes or other openings.
DO NOT operate this product inside any building or enclosure, even if windows and doors are open.
A
Running engines give off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monoxide can cause nausea, fainting, or death.
B
Read the manuals
Figure 4
grass bag to the rear of the mower
(Figure 7).
6
A
• Pull the starter rope handle (C) out of the engine to
the rope guide (D). Hook the starter rope into the
rope guide (it might be a tight fit).
3-in-1: Convert from mulching to bagging to side-discharge:
• Carefully read all the manuals supplied with the mower.
They contain important safety, operating, and maintenance
information.
Reproduction
• Holding the rear door open, attach the
1
For mulching:
3
To convert to side discharge:
Failure to read and follow instructions in the operator's manual could result in death and/or bodily injury.
• Leave the mulching cover and the
installed mulching plug in place (Figure 5).
• Make sure the mulching plug is installed
in the rear of the mower, and the grass
bag is removed.
A
A
2
To convert to bagging:
• Lift the rear door and remove the
installed mulching plug (Figure 6).
Figure 5
• Make sure the hooks on both sides of
the bag frame hook onto the rear
door rod (Figure 8).
• Release the rear door (it will rest on top
of the grass bag).
• Remove the oil fill cap (A, Figure 3). Add the entire contents of the
supplied oil container to the engine. Replace the oil fill cap.
Figure 7 • Lift the mulching cover, and install
the side discharge deflector onto the
mower deck (Figure 9).
• Make sure the deck tabs stick up through
the locking slots (Figure 10).
• Release the mulching cover (it will rest
on top of the discharge deflector).
Figure 9
© Briggs & Stratton Corporation
Figure 6 Figure 8
We reserve the right to improve our products and make changes in specifications, designs, and standard equipment without notice and without incurring obligation.
Figure 10 Mulching Plug
(Installed) Grass Bag
Side Discharge
Deflector
SAE30W
Oil
Operator’s
Manual
Form No. 7105027 (Rev. ‘-’)
A
GUÍA DE INSTALACIÓN RÁPIDA
Cortacésped tipo Walk Behind autopropulsado
Modelos
SPXV2270HW
NSPXV2270HW
¿Alguna pregunta?
No vuelva a la tienda. Nosotros podemos ayudarle.
Llame al número gratuito de atención al cliente:
1-800-317-7833
O visite nuestra página Web
www.snapper.com
ADVERTENCIA
EVITE LA MUERTE O LESIONES GRAVES
• Lea el Manual del usuario
• Mantenga los dispositivos de seguridad (protectores,
pantallas, interruptores, etc.) en su lugar y en funcionamiento.
• En las pendientes, utilice el cortacésped a lo ancho, nunca de
arriba a abajo.
• Quite todos los objetos que la cuchilla pueda hacer que
salgan despedidos.
• No corte el césped cuando los niños u otras personas estén
en los alrededores.
• Mire hacia abajo y hacia atrás antes y mientras se desplaza
marcha atrás.
• Espere al menos 2 minutos antes de añadirle carburante.
1
Desembale el cortacésped
• Corte las cuatro esquinas de la caja de arriba a abajo.
• Quite todo el material de embalaje del cortacésped.
• Localice e identifique todos los componentes incluidos con el cortacésped.
A
A
4
Añada aceite y combustible
• Desplace el cortacésped hasta una superficie lisa y nivelada.
• Quite la tapa del depósito del aceite (A, Figura 3). Añada al motor todo el contenido del recipiente de aceite suministrado. Vuelva a poner la tapa del depósito del aceite.
IMPORTANTE El cortacésped se envía sin aceite en el motor. Si no añade aceite antes de arrancar el motor, el motor resultará dañado.
B
Figura 3
Cuchilla
Combustible sin plomo (mínimo de 87 octanos)
• Quite la tapa del depósito de combustible (B). Siguiendo las instrucciones de
Tapa del depósito de combustible
Tapa de la desmenuzadora
PELIGRO
B tres pasos de la tarjeta FreshStart®, encaje el cartucho de mantenimiento del
PELIGRO
Manilla de la cuerda del motor de arranque
Palanca de ajuste de altura de corte
(en cada rueda)
2
Levante el conjunto de la manilla
B combustible en la parte inferior de la tapa del depósito de combustible.
• Añada combustible limpio, en buen estado y SIN PLOMO con un mínimo de
87 octanos, dejando 2,5 cm (una pulgada) de espacio en la parte alta del
RIESGO DE AMPUTACIONES Y DE
LANZAMIENTO DE OBJETOS
• Mantenga las manos y pies alejados de la cubierta.
• No utilice el cortacésped si el conducto de descarga
o todo el recogedor de hierba no están en el lugar
adecuado.
Información general
• Afloje, pero no quite, los nudos (A, Figura 1) de ambos lados petróleo alifático (64742-47-8).
Tapa de depósito de aceite y varilla medidora depósito para la expansión del combustible. NOTA: No se recomienda usar
Control de cuchillas (2)
Control de transmisión (2) de la manilla superior.
• Desenvuelva la manilla superior de manera que quede
3 alineada con la manilla inferior y apriete las perillas superiores.
• Quite la perilla del manilla, las arandelas y los pernos de transporte del manilla inferior (B).
• Levante el manilla inferior, alineándolo con uno de los tres juegos de orificios en la abrazadera. (La mayoría de los usuarios prefieren la posición intermedia). Vuelva a colocar los aditamentos que quitó y aprételos de un modo seguro.
Figura 1
Instalación de la manilla del motor de arranque
Not
• Apriete el control de la cuchilla (A, Figura 2) contra el control
de transmisión (B). NOTA: El control de la cuchilla y el control
C
D
for
B
5 mezclas de combustible que contengan más de un 10% de etanol.
IMPORTANTE El depósito de combustible tiene una capacidad de menos de 1,9 litros (medio galón).
IMPORTANTE NO mezcle aceite con combustible.
IMPORTANTE NO use combustible E85.
• Vuelva a colocar la tapa del depósito de combustible y limpie cualquier mancha.
Preparación final
• Mueva la palanca de ajuste de la altura de corte (A, Figura 4) hasta la altura de corte deseada.
• Fije el cortacésped para triturar, aspirar o descargar. (Consulte las instrucciones 3 en 1 a continuación.)
A
ADVERTENCIA
Los motores cuando funcionan expulsan monóxido de carbono, y un gas venenoso, sin color y sin olor. Respirar monóxido de carbono puede causar náuseas, mareos o incluso la muerte.
Use este producto SÓLO en exteriores.
Evite que el gas expulsado entren en un área sin respiración por ventanas, puertas, tomas de ventilación u otras aperturas.
NO use este producto dentro de ningún edificio o lugar cerrado, incluso si las ventanas y las puertas están abiertas.
A
de transmisión pueden manejarse desde cualquier lado.
A
B
Lea los manuales
Figura 4 6
• Tire de la manilla del motor de arranque (C) hacia fuera del
A la bolsa para hierba a la parte
• Lea detenidamente todos los manuales proporcionados con el cortacésped.
motor hasta la guía para la cuerda (D). Enganche la cuerda
del motor de arranque en la guía para la cuerda (debe
quedar tensa).
3 en 1: Puede pasar del triturado a la aspiración y a la descarga lateral:
1
Para la trituración:
Reproduction
• Manteniendo la puerta trasera abierta, conecte
Contienen información importante sobre su seguridad, utilización y mantenimiento.
3
Para pasar a la descarga lateral:
ADVERTENCIA
No leer ni respetar las instrucciones del manual del usuario puede ocasionar la muerte o lesiones corporales.
A
A
Elementos que necesitará
El estabilizador de combustible es un producto químico peligroso. SI SE INGIERE, llame a un medico inmediatamente.
El estabilizador de combustible contiene:
2.6-di-tert-butilfenol (128-39-2) y destilado de
• Deje la tapa de la trituradora y el tapón de cubrición colocados (Figura 5).
trasera del cortacésped (Figura 7).
• Asegúrese de que el tapón de cubrición esté instalado en la parte posterior del cortacésped y que la bolsa para la hierba esté quitada.
A
Componentes incluidos
FreshStart ® Cartucho del mantenimiento de combustible
2
Para pasar a aspirar:
Figura 5 Figura 7
• Levante la cubierta de la cubridora de suelos e instale el deflector de descarga lateral en la cubierta del cortacésped (Figura 9).
Figura 9
• Levante la puerta trasera y quite el tapón de cubrición instalado (Figura 6).
• Asegúrese de que los ganchos de ambos lados de la estructura de la bolsa se enganchen en la varilla de la puerta trasera (Figura 8).
• Asegúrese de que las fichas de la cubierta se adhieran por las ranuras de bloqueo (Figura 10).
• Libere la puerta trasera (descansará sobre la parte superior de la bolsa para la hierba).
• Libere la tapa de la trituradora (descansará sobre la parte superior del deflector de descarga).
Tapón de cubrición de suelos (instalado)
Bolsa para hierba
Deflector de descarga lateral
Aceite
SAE30W
Manual del usuario
© Briggs & Stratton Corporation
Figura 6 Figura 8
Nos reservamos el derecho de mejorar nuestros productos y realizar cambios en las especificaciones, diseños y equipos estándar sin previo aviso y sin incurrir en obligación.
Figura 10
Nº de formulario 7105027 (Rev. ‘-’)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project