Speco Technologies VL7038IRVF Camcorder Instruction manual
Add to my manuals
33 Pages
Speco Technologies VL7039IRVF is a day/night weatherproof bullet camera that offers high-quality surveillance capabilities for both indoor and outdoor applications. With its 1/3” Sony Super HAD ll CCD image sensor and DC auto iris varifocal lens (6mm-50mm), this camera delivers sharp and detailed images with a resolution of 600TV lines.
The VL7039IRVF features true day/night capability, allowing it to automatically switch between color and black-and-white modes depending on the lighting conditions. It also incorporates an ICR (infrared cut filter) that can be manually removed to enhance night vision. Additionally, the camera is equipped with 63pcs 850nm IR LEDs, providing up to 131ft of night vision range.
advertisement
INSTRUCTION
MANUAL
DNR Bullet Day/Night
Weather-proof Camera
VL7038IRVF
VL7039IRVF
Speco Technologies is constantly developing product improvements.
We reserve the right to modify product design and specifications without notice and without incurring any obligation.
Rev. 6/20/2012
Contents
◑ Contents ...................................................... 1
◑ Precautions ................................................. 2, 3
◑ Safety Instructions ...................................... 4
◑ Package Contents ....................................... 5
◑ Camera Installation ..................................... 6-8
◑ Specifications .............................................. 9, 10
◑ Camera Dimension ..................................... 11
◑ Features ...................................................... 12
◑ OSD Menu Details ...................................... 13-26
◑ Trouble Shooting ......................................... 27
1
Do not install the camera in extreme temperature conditions.
Precautions
Do not install the camera under unstable lighting conditions.
Do not touch the front lens of the camera.
Only use the camera under conditions where temperatures are between
-10°C and +50°C. Be especially careful to provide ventilation when operating under high temperatures.
Severe lighting change or flicker can cause the camera to work improperly.
Never keep the camera pointed directly at strong light.
Do not drop the camera or subject it to physical shocks.
This is one of the most important parts of the camera. Be careful not to leave fingerprints on the lens cover.
Do not expose the camera to radioactivity.
It can cause malfunctions to occur.
Housing damage can compromise wheatherproof ratings.
If exposed to radioactivity the CCD will fail.
NOTE
* If the camera is exposed to spotlight or object reflecting strong light, smear or blooming may occur.
* please check that the power satisfies the normal specification before connecting the camera.
2
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
ISO14001
The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
☞
Do NOT use power sources other than those specified.
This installation should be made by a qualified service person and should conform to all local codes.
3
Safety Instructions
Precautions for use
◑ This camera should be installed by qualified personnel only
◑ There are no user serviceable parts inside
◑ Do not disassemble this camera other than to make initial adjustments
◑ Use a UL approved regulated 24 volt AC or 12 volt DC power supply
◑ Use appropriate low voltage power cable to prevent fire or electrical shock
◑ Please insure that your installation area can support the weight of the camera
Please handle this camera carefully :
◑ Do not use a strong or abrasive detergent when cleaning the camera
◑ Do not install near cooling or heating device
4
Package Contents
Please make sure that the following items are included in the Package:
1) VL7038IRVF, VL7039IRVF
• 1 Video Test Connector, Power Jack
• 1 3Axis Bracket Round Base Adaptor
• 2 Wrenches
• Set Screw
- 4 Tapping Screws 4x25
- 4 Hexagon Socket Screws M5x15
5
CAMERA INSTALLATION jvuulj{Gwv~lyGjhislG
XUG~oluG|zpunGXYG}vs{zGkjGOGG\WWGhPG wGpGaylk jGaGORP kjGXY}GwGz
YUG~oluG|zpunGY[G}vs{zGhjGO[WG}GhP ylkORP ishjraOTP hjGY[} wGz
ZUGjvuulj{G}pklvGjhislG
T jvuulj{GiujGjhislG{vG{olGiujGqhjrUG
6
CAMERA INSTALLATION
Compatibility
1) VL7038IRVF, VL7039IRVF
INTJBS INTCM
7
CAMERA INSTALLATION
1. VL7038IRVF, VL7039IRVF
CAMERA ASSEMBLY
WALL
3AXIS BRACKER ROUND BASE ADAPTOR
TAPPING SCREW 4X25, 4EA
HEXAGON SOCKET SCREW M5X15, 4EA
8
Day/Night Weather-proof Bullet Camera
DC Auto Iris Varifocal Lens(2.8mm-12mm) / IR LED Built-in 63pcs
■
VL7038IRVF
600TV Lines
DC Auto Iris Varifocal
Lens(2.8mm-12mm)
True Day/Night Capability
ICR-IR Cut Filter Removable
850nm IR LEDs * 63pcs
SPECIFICATIONS
MODEL
Image Pick-Up Device
TV System
Total Pixels
Effective Pixels
Scanning Frequency
Scanning System
Synchronization
Resolution
Minimum Illumination
S/N Ratio
Video Output
Electronic Shutter Speed
OSD
SSDR
BLC
Day & Night
Gain Control
White Balance
SENS-UP
Motion Detection
Privacy Masking
SSNR III (Digital Noise Reduction)
Digital Zoom
DIS (Digital Image Stabilizadion)
Sharpness
Filp / Mirror
Power Supply
Power Consumption
Lens
IR Distance
Operational Temp.
Storage Temp.
Dimension
Weight
VL7038IRVF
1/3” Sony Super HAD ll CCD
NTSC, PAL
NTSC=811(H) * 508(V) / PAL=795(H) * 596(V)
NTSC=768(H) * 494(V) / PAL=752(H) * 582(V)
NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V)
2:1 Interlace
Internal
600TV Lines
CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux
More than 52dB
CVBS: 1.0Vp-p / 75Ω
NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec)
Available
On / Off (Level adjustable)
BLC / HLC / OFF
Color / BW / AUTO / EXT
Low / High / Off
ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)
Auto / Off (Selectable x2 ~ x512)
On / Off (8 Programmable Zones)
On / Off (12 Programmable Zones)
On / Off (Level adjustable)
On / Off (x1 ~ x16)
On / Off
On / Off (Level adjustable)
On / Off
DC 12V / AC24V(Dual Voltage)
DC 12V 220mA(CDS OFF) / 700mA(CDS ON)
Heater ON Adj:220~700mA
AC 24V 150mA(CDS OFF),450mA(CDSON)
Heater ON Adj:170~450mA
DC Auto Iris Varifocal Lens(2.8mm-12mm)
131 ft
-4˚F ~ +140˚F RH 95% Max.
-4˚F ~ +140˚F RH 95% Max.
5.31"(W) * 3.74"(H) * 11.57"(D)
3.96 lbs
9
Day/Night Weather-proof Bullet Camera
DC Auto Iris Varifocal Lens(6mm-50mm) / IR LED Built-in 63pcs
■
VL7039IRVF
600TV Lines
DC Auto Iris Varifocal
Lens(6mm-50mm)
True Day/Night Capability
ICR-IR Cut Filter Removable
850nm IR LEDs * 63pcs
SPECIFICATIONS
MODEL
Image Pick-Up Device
TV System
Total Pixels
Effective Pixels
Scanning Frequency
Scanning System
Synchronization
Resolution
Minimum Illumination
S/N Ratio
Video Output
Electronic Shutter Speed
OSD
SSDR
BLC
Day & Night
Gain Control
White Balance
SENS-UP
Motion Detection
Privacy Masking
SSNR III (Digital Noise Reduction)
Digital Zoom
DIS (Digital Image Stabilizadion)
Sharpness
Filp / Mirror
Power Supply
Power Consumption
Lens
IR Distance
Operational Temp.
Storage Temp.
Dimension
Weight
VL7039IRVF
1/3” Sony Super HAD ll CCD
NTSC, PAL
NTSC=811(H) * 508(V) / PAL=795(H) * 596(V)
NTSC=768(H) * 494(V) / PAL=752(H) * 582(V)
NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V)
2:1 Interlace
Internal
600TV Lines
CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux
More than 52dB
CVBS: 1.0Vp-p / 75Ω
NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec)
Available
On / Off (Level adjustable)
BLC / HLC / OFF
Color / BW / AUTO / EXT
Low / High / Off
ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)
Auto / Off (Selectable x2 ~ x512)
On / Off (8 Programmable Zones)
On / Off (12 Programmable Zones)
On / Off (Level adjustable)
On / Off (x1 ~ x16)
On / Off
On / Off (Level adjustable)
On / Off
DC 12V / AC24V(Dual Voltage)
DC 12V 220mA(CDS OFF) / 700mA(CDS ON)
Heater ON Adj:220~700mA
AC 24V 150mA(CDS OFF),450mA(CDS ON)
Heater ON Adj:170~450mA
DC Auto Iris Varifocal Lens(6mm-50mm)
131 ft
-4˚F ~ +140˚F RH 95% Max.
-4˚F ~ +140˚F RH 95% Max.
5.31"(W) * 3.74"(H) * 11.57"(D)
3.96 lbs
10
CAMERA DIMENSION
1) VL7038IRVF / VL7039IRVF
5.31”
5.98”
11.57”
4.76” 11.22”
11
General Features
◑ Ultra High Sensitivity
- The built-in high sensitivity COLOR CCD produces a clear image even in 0Lux(B/W, IR-LED ON)or lower illumination.
◑ 600TV Lines
- By adopting a diagonal 6mm(1/3") 410,000 (NTSC) pixel, 470,000(PAL) pixel SONY CCD, the camera produces clear picture quality with a horizontal resolution of 600 TV lines for color and a horizontal resolution of 700TV lines for BW mode.
◑ DNR3
- The high-performance W-V DSP chip effectively removes low-light gain noise and ghosting to provide clear images even in dark environments.
◑ Day & Night
- This camera has a function that automatically selects the mode that is appropriate for daytime or night-time conditions.
The COLOR mode operates in daytime conditions to provide optimum colors, and BW mode operates in night-time conditions to enhance the definition of the image.
◑ SSNR
- For images with high contrast between bright and dark Areas from difficult lighting conditions such as backlighting, this camera selectively illuminates darker Areas while retaining the same light level for brighter Areas to even out the overall brightness.
◑ Miscellaneous Functions
- HLC(High Light Compensation), SENS-UP, FLIP(H/V-REV), D-ZOOM, SHARPNESS, MOTION DETECTION and PRIVACY functions are provided.
◑ Disk Saving Effects
- Up-most and advanced DNR technology camera picture quality has a disk saving effects due to Image sizes are smaller than standard CCTV camera image.
◑ Controlled by OSD Menu
- The camera can be controlled by selecting the menu text displayed on the monitor screen.
12
OSD Control Button
1. Type A, Type B, Type C of OSD button could be used when it needs to
OSD control.
2. Type D is extra Option (wired Remote controller)
▲ Up button: Moves the cursor upwards. Use this button to select an item
or adjust the parameters.
▼ Down button: Moves the cursor downwards. Use this button to select an
item or adjust the parameters.
◀ Left button: Moves the cursor to the left. Use this button to select or
adjust the parameters of the selected item. The parameter changes
each time this button is pressed.
▶ Right button: Moves the cursor to the right. Use this button to select or
adjust the parameters of the selected item. The parameter changes each
time this button is pressed.
◎ Set button: Executes selections and displays a submenu for an item with
the mark.
13
●
Menu Setup
1. Press the Function Setup switch.
- Main setup menu is displayed on the monitor screen.
1.LENS
MAIN SETUP
DC
2.EXPOSURE
3.WHITE BAL
4.SSNR
5.BACKLIGHT
6.DNR3
7.DAY/NIGHT
8.SPECIAL
9.EXIT
ATW
OFF
OFF
ON
AUTO
SAVE
2. Select a desired function using the Function Setup switch.
- Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4. To finish the setting, select 'EXIT' and press the Function Setup switch.
☞ NOTE
■ An item with the ◀ icon also has sub menus. To select a sub menu, select an item with the icon and press the Function Setup switch.
■ An item with the - - - icon is unavailable due to function settings.
●
Lens Setting
Using this function, you can control the screen brightness.
1. When the SETUP menu screen is displayed, select 'LENS' by using
the Function Setup switch so that the arrow indicates 'LENS'.
2. DC : You can adjust the minimum shutter and maximum value of ESC
shutter mode.
MAIN SETUP
1.LENS
2.EXPOSURE
3.WHITE BAL
DC
ATW
3. THE Lens mode has sub menu items as listed below.
- BRIGHTNESS : Adjusts the video brightness.
14
- FOCUS ADJ : To adjust the DC lens focus correctly, you must activate the
Focus Settings mode under each lens menu. Activate the Focus Settings mode, adjust the lens focus, and then deactivate the settings mode.
☞ NOTE
■ If color rolling occurs when using a DC lens, set Shutter to Fixed (---).
●
Exposure Setting
1.LENS
MAIN SETUP
DC
2.EXPOSURE
3.WHITE BAL ATW
1. When the SETUP menu screen is displayed, select 'EXPOSURE' by using the Function Setup Switch.
2. Select a desired mode using the Function Setup switch.
EXPOSURE SETUP
1.BRIGHTNESS
2.SHUTTER
3.AGC
4.SENS-UP
5.RETURN
25
- - -
HIGH
OFF
◆ SHUTTER : You can select either auto or manual shutter.
* --- : Shutter speed is fixed at 1/60sec(1/50sec)
* ESC : Select this to control the shutter speed automatically. If ESC is
selected, the shutter speed is automatically controlled depending
on the ambient illumination of the subject.
* MANUAL : You can control shutter speed manually.
(NTSC MODEL : 1/60~1/120,000, PAL MODEL : 1/50~1/120,000)
* A.FLK : Select this when you see picture flicker, this can happen when the
frequency of the local lighting clashes with the camera.
☞ NOTE
■ When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
15
◆ AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen
- but the higher the noise.
* OFF : Deactivates the AGC function.
* LOW : Allows automatic gain control from 5.3dB to 32dB.
* HIGH : Allows automatic gain control from 5.3dB to 37dB.
◆ SENS-UP : When it is night or dark, the camera automatically detects the light
level and maintains a clear picture if this mode is activated.
* OFF : Deactivates the SENS-UP function.
* AUTO : Activates the SENS-UP function.
◆ RETURN : Select this to save the changes in the EXPOSURE menu and return
to the SETUP menu.
☞ NOTE
■ If you press the Function Setup switch to ‘AUTO’ mode, you can adjust brightness by increasing or decreasing the shutter speed. (x2 ~ x512)
■ Note that the higher the zoom level, the brighter the screen, but the more likely there will be a ghosting effect.
■ It is normal for Noise, Spots and Whitish symptoms to appear in SENS-UP mode when the D-ZOOM level is increased.
●
White Balance (White Bal) Setting
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select 'White Bal' by using the
Function Setup switch so that the arrow indicates 'White Bal'.
2. Select a desired mode using the Function Setup switch.
1.LENS
MAIN SETUP
DC
2.EXPOSURE
3.WHITE BAL ATW
16
※ Select one of the following 5 modes, as appropriate for your purpose.
◆ ATW : Select this when the color temperature is between 1,700˚K and 11,000˚K.
◆ OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K.
(sodium light inclusion)
◆ INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K.
◆ MANUAL : Select this to fine-tune White Balance manually. Set White Balance first
by using the ATW or AWC mode. After that switch to MANUAL mode,
fine-tune the White Balance and then press the Function Setup switch.
◆ AWC→SET : To find the optimal luminance level for the current environment, point
the camera towards a sheet of white paper and press the Function
Setup switch. If the environment changes, readjust it.
☞ NOTE
■ White Balance may not work properly under the following conditions. In this case select the AWC mode.
① When the color temperature of the environment surrounding the subject is out of the control range (e.g. clear sky or sunset).
② When the ambient illumination of the subject is dim.
③ If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, the White Balance operation may become unstable.
●
SSNR Setting
SSNR illuminates darker spots of an image while retaining the same light level for brighter spots to even out the overall brightness of images with high contrast between bright and dark spots.
1.LENS
MAIN SETUP
DC
2.EXPOSURE
3.WHITE BAL
4.SSNR
ATW
OFF
1. When the SETUP menu screen is displayed, select 'SSNR' by using the switch so that the arrow indicates 'SSNR'.
2. Use the switch to change the SSNR level according to the contrast between bright and dark areas.
17
●
Backlight Setting
Unlike conventional cameras, the SIR-4160 is designed to deliver a distinctive subject and background at the same time, even when the subject is backlight, by using the features of the proprietary W-V DSP chip.
1. When the SETUP menu screen is displayed, select 'BACKLIGHT' by using the Function Setup switch so that the arrow indicates 'BACKLIGHT'.
1.LENS
MAIN SETUP
DC
2.EXPOSURE
3.WHITE BAL
4.SSNR
5.BACKLIGHT
6.DNR3
7.DAY/NIGHT
8.SPECIAL
9.EXIT
ATW
OFF
OFF
ON
AUTO
SAVE
2. Select a desired mode using the Function Setup switch.
◆ BLC : Enables a user to directly select a desired area from a picture, and to view
the area more clearly.
◆ HLC (High Light Compensation) : If the scene contains extremely bright light areas
such as; from car headlights, the light can mask out much of the on-screen detail
- LEVEL : Adjust level of the HLC function.
- LIMIT : Enable to change the operating condition.
- MASK COLOR/TONE : Change the color / transparency of the masking area.
(Black, Red, Blue, Cyan, Magenta)
- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced
◆ OFF : Not being used
2. Select a desired mode using the Function Setup switch and press the Function Setup switch.
◆ Select 'BLC' to adjust the area to be enhanced then adjust the level.
◆ Select 'BLC' to adjust the area to be enhanced then adjust the level.
18
BLC SETUP
LEVEL
TOP
BOTTOM
LEFT
RIGHT
Press Set to Return
LOW
38
109
54
121
HLC SETUP
LEVEL
LIMITS
MASK COLOR
MASK TONE
TOP
BOTTOM
LEFT
RIGHT
Press Set to Return
MIDDLE
NIGHT ONLY
BLACK
120
5
1
5
172
☞ NOTE
■ Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance.
■ When dark, the HLC is only activated when a bright light exceeding a specific size in
NIGHT ONLY mode.
■ The HLC is not activated in day light or when bright light is not present at night in NIGHT
ONLY mode.
■ BLC Function doesn't work in the B/W mode of the DAY/NIGHT menu.
●
DNR3 Setting
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select 'DNR3' by using the
Function Setup switch so that the arrow indicates 'DNR3'.
1.LENS
MAIN SETUP
DC
2.EXPOSURE
3.WHITE BAL
4.SSNR
5.BACKLIGHT
6.DNR3
7.DAY/NIGHT
8.SPECIAL
9.EXIT
ATW
OFF
OFF
ON
AUTO
SAVE
2. Select a desired mode using the Function Setup switch.
◆ OFF : Deactivates DNR3. Noise is not reduced.
◆ ON : Activates DNR3 so that noise is reduced.
19
3. Set the DNR3 mode to 'ON' and press the Function Setup switch. Then you can adjust the noise reduction level.
☞ NOTE
■ You cannot set the DNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’.
■ When adjusting the noise reduction level in the DNR3 mode, remember that the higher the level set, the more the noise level will be reduced, as will the brightness of the image.
●
Day/Night Setting
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select 'DAY/NIGHT'by using the
Function Setup switch so that the arrow indicates 'DAY/NIGHT'.
1.LENS
MAIN SETUP
DC
2.EXPOSURE
3.WHITE BAL
4.SSNR
5.BACKLIGHT
6.DNR3
7.DAY/NIGHT
8.SPECIAL
9.EXIT
ATW
OFF
OFF
ON
AUTO
SAVE
2. Select a desired mode using the Function Setup Switch according to the picture display you want.
◆ COLOR : The picture is always displayed in color.
◆ B/W : The picture is always displayed in black and white.
- BURST MODE : You can turn on or off the burst
signal on B/W mode.
- IR MODE : When IR LED is turned on in B/W, the
objects can be clearly identified due to
the function that decreases screen saturation
of objects within a short distance.
- TOP/BOTTOM/LEFT/RIGHT : Adjust the range according to
the location of objects.
- IR LEVEL : Select LOW when objects appears within a
short distance or select HIGH when objects
appear within a long distance on the screen.
B/W MODE SETUP
1.BURST MODE
2.IR MODE
3.IR LEVEL
4.RETURN
ON
ON
HIGH
20
◆ AUTO : The mode is switched to 'Color' in a normal environment, but switches to
'B/W' mode when ambient illumination is low. To set up the switching time for AUTO mode, press the Function Setup switch. You can turn on or off the burst signal on B/W mode.
AUTO SETUP
- BURST MODE : You can turn on or off the burst signal
ON
on B/W mode.
- DURATION : You can select brightness of illumination
about changing the day/night mode.
- DWELLTIME : You can select the duration time about
changing the day/night mode.
→3s, 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s
1.BURST MODE
2.COLOR→B/W
DURATION
DWELL TIME
3.B/W→COLOR
DURATION
DWELL TIME
4.RETURN
FAST
3SEC
FAST
10SEC
FAST
SLOW
COLOR→B/W
2.5 lux
1 lux
B/W→COLOR
5 lux
10 lux
* The day/night switching point of the
camera can be adjusted.
☞ NOTE
■ When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR' mode and 'AUTO' mode can not be selected.
●
Special Setting
1. When the SETUP menu screen is displayed, select 'SPECIAL' by using the
Function Setup switch so that the arrow indicates 'SPECIAL'.
1.LENS
MAIN SETUP
DC
2.EXPOSURE
3.WHITE BAL
4.SSNR
5.BACKLIGHT
6.DNR3
7.DAY/NIGHT
8.SPECIAL
9.EXIT
ATW
OFF
OFF
ON
AUTO
SAVE
21
2. Select a desired mode using the Function Setup switch.
SPECIAL
1.IMAGE ADJ
2.CAM TITLE
3.SYNC
4.MOTION DET
5.PRIVACY
6.DIS
7.COMM ADJ
8.LANGUAGE
9.RETRUN
OFF
INT
OFF
OFF
OFF
ENGLISH
◆ IMAGE ADJ. :
1) When the SETUP menu screen is displayed, select 'IMAGE ADJ' by using the Function Setup switch so that the arrow indicates 'IMAGE ADJ'.
2) Select a desired mode using the Function Setup switch.
IMAGE SETUP
1.V-REV
2.H-REV
3.D-ZOOM
4.FONT COLOR
5.SHARPNESS
6.MONITOR
7.RETURN
OFF
OFF
WHITE
ON
LCD
* V-REV : You can flip the picture vertically on the screen.
* H-REV : You can flip the picture horizontally on the screen.
* D-ZOOM : You can use a digital zoom of x1 ~ x16.
* FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue)
* SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer.
Adjust this value appropriately depending on the sharpness of the picture.
* MONITOR : Please change the settings value of video appropriate to your monitor.
- LCD : Please select this menu item when using a LCD monitor.
- CRT : Please select this menu item when using a CRT monitor.
- USER : Please use this menu item when using a monitor other than standard ones. You can
change the gamma, PED level, and color gain in the sub menus.
* RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to the SETUP menu.
22
☞ NOTE
■ When the V-REV or H-REV mode is enabled, the text on the screen does not flip.
■ If you increase the SHARPNESS level too high, the picture may become distorted or noise may appear.
◆ CAM TITLE : If you enter a title, the title will appear on the monitor.
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates 'CAM TITLE'.
CAMERA TITLE SETUP
2) Set it to 'ON' by using the Function Setup switch.
3) Press the Function Setup switch.
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
4) Use the Function Setup switch to move to a desired letter and select the letter by pressing a b c d e f g h i j k l m n o p q r s t u v w x y z the Function Setup switch. Repeat this to enter multiple letters. You can enter up to 15 letters.
- . 0 1 2 3 4 5 6 7 8 9
←→CLR POS END
5) Enter a title, move the cursor to 'POS' and press the Function Setup switch. The entered title appears on the screen. Select the position to display the title on the screen by using the
Function Setup switch and press the Function
Setup switch. When the position is determined, select 'END' and press the Function Setup switch to return to the SPECIAL menu.
SHOP
☞ NOTE
■ When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you enter one.
■ Only English is available in this mode.
■ If you move the cursor to CLR and press the Function Setup switch, all the letters are deleted. To edit a letter, change the cursor to the bottom left arrow and press the Function
Setup switch. Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the Function Setup switch.
◆ SYNC : In areas where the supply is at 60Hz(NTSC), 50Hz(PAL), you can synchronize
the output phase of multiple cameras using the power synchronization function
(Line-Lock) without using a synchronization signal generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
* Press the Function Setup switch.
* You can select a desired phase from 0 to 359 when select 'phase'.
23
☞ NOTE
■ When using AC power at 60Hz(NTSC), 50Hz(PAL), frequency, you can use the L/L type synchronization.
■ When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.
◆ MOTION DET :This product has a feature that allows you to observe movement of objects in 8 different areas on the screen, and the words 'MOTION DETECTED' appear on the screen when movement is detected.
Activity can be monitor more efficiently.
1) When the SPECIAL menu screen is displayed,
MOTION DET
1.SENSITIVITY
2.AREA MODE
3.SEL POS
4.XPOS
5.YPOS
6.FILL → SET
7.RETRUN
AREA1
ON
L-TOP
3
5 press the Function Setup switch so that the arrow indicates‘MOTION DET’.
2) Set up the mode using the Function Setup switch.
- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high, motion
detection sensitivity is increased to recognize even small movement.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- FILL→SET : Fills in a selected MD area. The color of the area can be selected from brown,
orange, blue, cyan, green, yellow, magenta and red.
- RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu.
◆ PRIVACY : Mask an area you want to hide on the screen.
PRIVACY AREA SETUP
1.AREA
2.MODE
3.MASK COLOR
4.MASK TONE
5.TOP
6.BOTTOM
7.LEFT
8.RIGHT
9.RETURN
AREA1
OFF
GREEN
1
39
79
13
52
24
1) When the SPECIAL menu screen is displayed, press the Function
Setup switch so that the arrow indicates 'PRIVACY'.
2) Set up the mode using the Function Setup switch.
- AREA : You can select up to 12 PRIVACY areas.
- MODE : Determines whether to use the area selected in the AREA.
- MASK COLOR : Determine area color. You can select Green, Red, Blue, Black, White, Gray.
- MASK TONE : Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT :Adjust the size and position of the selected area.
- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.
◆ DIS (Digital Image Stabilizer) :
This function mitigates any picture movement due to external factors such as wind.
☞ NOTE
■ As the DIS function uses the digital zoom the camera's resolution will decrease.
■ DIS doesn’t operate when background illumination is too low.
■ DIS doesn’t operate when object pattern is monotonic as like sky or white wall.
◆ COMM ADJ (Communication Adjustment) :
This function sets up the camera communication status when controlling the camera through an external control device.
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates 'COMM ADJ'.
2) Set up the mode using the Function Setup witch.
- CAM ID : Determines the camera's identification number (between 0 and 255).
- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600 bps.
- UART MODE : You can select NONE, EVEN or ODD for the parity bits.
- RET PKT : Determines whether to send a command back to the controller device when a
communication control command is sent to the camera.
- DISP ID : Display camera title on top left corner of the screen.
- PROTOCOL : You can select one of various protocols. STW(SPD), PELCO-P, PELCO-D,
VICON, PANASONIC, BOSCH, HONEYWELL, SEC.
* Initial value of communication adjustment
Item
Initial value
Camera ID
1
BAUD RATE
9600
UART MODE
8-NONE-1
PET PKT
ENABLE
25
◆ LANGUAGE : You can select the menu language according to your requirements.
◆ RETURN : Select this to save the SPECIAL menu settings and return to the MAIN
SETUP menu.
●
Exit Setting
Select a desired EXIT mode using the Function Setup Switch.
- SAVE : Save the current settings and exit the MAIN SETUP menu.
- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.
- RESET : Resets the camera settings to the factory defaults. Language,
Communication and Monitor Settings are not initialized.
26
●
Trouble Shooting
PROBLEM
Northing appears on the screen.
The image on the screen is dim.
The image on the screen is dark.
POSSIBLE CAUSE
☞ Check the power cable, power supply output and video connection between the camera and monitor.
☞ Are the camera lens or the lens glass dirty?
Clean the lens / glass with a soft clean cloth.
☞ Adjust the monitor controls, as required.
☞ If the camera is facing a very strong light, change
the camera position.
☞ Adjust the lens focus.
☞ Adjust the contrast control of the monitor.
☞ If there is an intermediate device, correctly set the 75Ω/Hi-z.
☞ Check the camera is correctly connected to an appropriate
regulated power source.
☞ Has MOTION DET been set to ON in the menu?
☞ Has MD AREA been properly defined?
Motion Detection is not activated.
The color of the picture is not correct.
The image on the screen flickers.
The SENS-UP does not work.
☞ Check the settings in WHITE BALANCE menu.
☞ Make sure that the camera isn’t facing direct sunlight or
fluorescent lighting. If necessary,change the camera position.
☞ Check that the AGC setting in the EXPOSURE menu is’t set to OFF.
☞ Check the EXPOSURE menu and make sure SHUTTER is set to------.
27
28
▶ MEMO
29
▶ MEMO
30
▶ MEMO
31
200 New Highway
Amityville, NY 11701
631-957-8700
1 800 645 5516 www.specotech.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement