- Computers & electronics
- Computer components
- System components
- Server/workstation motherboards
- Supero
- H8DCT-HIBQF
- User manual
advertisement
S
UPER
®
H8DCT-HLN4F
H8DCT-HIBQF
USER’S MANUAL
Revision 1.1a
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com
.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license.
IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE
OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC. SHALL
NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.
FCC Statement: Refer to Supermicro's web site for FCC Compliance Information.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate ”.
WARNING: Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm.
Manual Revision 1.1a
Release Date: March 06, 2014
Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this document.
Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.
Copyright © 2014 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
Preface
Preface
About This Manual
This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the H8DCT-HLN4F/HIBQF serverboard.
The H8DCT-HLN4F/HIBQF serverboard is based on the AMD® SR5670 or SR5690 and SP5100 chipset and supports two AMD Socket C32 type processors with up to 192 GB of ECC RDIMM.
The differences between the features of the H8DCT-HLN4F and H8DCT-HIBQF serverboards are shown in the table below.
Features
SR5690SP5100 Chipset
SR5670/SP5100 Chipset
Infi niBand® Controller
2x 1Gb Ethernet LAN
4x 1Gb Ethernet LAN
H8DCT-HLN4F
Yes
H8DCT-HIBQF
Yes
Yes
Yes
Yes
Please refer to the motherboard specifi cations pages on our web site for updates on supported processors ( http://www.supermicro.com/aplus/ ). This product is intended to be professionally installed.
Manual Organization
Chapter 1 includes a checklist of what should be included in your motherboard
box, describes the features, specifi cations and performance of the motherboard and provides detailed information about the chipset.
Chapter 2 begins with instructions on handling static-sensitive devices. Read this
chapter when installing the processor(s) and memory modules and when installing the motherboard in a chassis. Also refer to this chapter to connect the hard disk drives, the various ports, and the power and reset buttons and the system LEDs.
If you encounter any problems, see Chapter 3, which describes troubleshooting procedures for the video, the memory and the setup confi guration stored in CMOS.
For quick reference, a general FAQ (Frequently Asked Questions) section is provided. Instructions are also included for contacting technical support. In addition, you can visit our web site for more detailed information.
Chapter 4 includes an introduction to BIOS and provides detailed information on
running the CMOS Setup utility.
iii
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Appendix A provides BIOS Error Beep Code Messages.
Appendix B lists BIOS POST Checkpoint Codes.
iv
Table of Contents
Table of Contents
Chapter 1 Introduction
Checklist .......................................................................................................... 1-1
AMD AMD SR5670 or SR5690 and SP5100 Chipset .................................. 1-10
HyperTransport Technology .......................................................................... 1-10
1-5 PC Health Monitoring .................................................................................... 1-10
Chapter 2 Installation
2-1 Standardized Warning Statements ................................................................. 2-1
About Standardized Warning Statements ....................................................... 2-1
Precautions ..................................................................................................... 2-4
Unpacking ....................................................................................................... 2-4
2-3 Processor and Heatsink Installation................................................................ 2-5
2-4 Mounting the Serverboard into a Chassis ...................................................... 2-7
Memory Support .............................................................................................. 2-8
Maximum Memory ........................................................................................... 2-8
DIMM Module Population Confi guration .................................................... 2-9
2-6 PCI Expansion Cards .................................................................................... 2-10
2-7 I/O Port and Control Panel Connections .......................................................2-11
Fan Header .............................................................................................. 2-12
LAN1/2/3/4 (Ethernet Ports) ..................................................................... 2-12
Unit Identifi er Button ................................................................................. 2-12
IPMB ......................................................................................................... 2-13
Overheat LED ........................................................................................... 2-13
USB Headers ........................................................................................... 2-13
JP1 Adapter Card Connector ................................................................... 2-13
Trusted Platform Module Header ............................................................. 2-14 v
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
SXB1 Adapter Card Slot/Connector ......................................................... 2-14
Explanation of Jumpers ................................................................................ 2-15
CMOS Clear ............................................................................................. 2-15
I2C to PCI-Express Slots ......................................................................... 2-16
BMC Jumper ............................................................................................ 2-16
VGA Enable/Disable ................................................................................. 2-16
LAN Enable/Disable ................................................................................ 2-16
Infi niBand Port Enable/Disable ............................................................... 2-16
Watch Dog Enable/Disable ...................................................................... 2-17
LAN1/LAN2/LAN3/LAN4 LEDs ................................................................. 2-17
Power LED ............................................................................................... 2-17
Dedicated IPMI LAN LEDs ..................................................................... 2-18
Infi niBand LED Indicators ......................................................................... 2-18
IPMI LED .................................................................................................. 2-18
UID LED (LE1) ........................................................................................ 2-19
2-11 Enabling SATA RAID ..................................................................................... 2-20
Serial ATA (SATA).......................................................................................... 2-20
Installing the OS/SATA Driver ....................................................................... 2-20
Building a Driver Diskette ......................................................................... 2-20
Enabling SATA RAID in the BIOS ................................................................. 2-21
Using the DotHill and Adaptec RAID Utility .................................................. 2-23
Installing the RAID Driver During OS Installation ......................................... 2-23
Supero Doctor III ........................................................................................... 2-25
Chapter 3 Troubleshooting
Before Power On ............................................................................................ 3-1
No Power ........................................................................................................ 3-1
No Video ......................................................................................................... 3-2
Memory Errors ............................................................................................... 3-2
Losing the System’s Setup Confi guration ....................................................... 3-2
3-2 Technical Support Procedures ........................................................................ 3-2 vi
Table of Contents
3-4 Returning Merchandise for Service................................................................. 3-4
Chapter 4 BIOS
4-3 Advanced Settings Menu ................................................................................ 4-2
Appendix A BIOS Error Beep Codes
Appendix B BIOS POST Checkpoint Codes
B-1 Uncompressed Initialization Codes ................................................................. B-1
B-2 Bootblock Recovery Codes ............................................................................. B-2
B-3 Uncompressed Initialization Codes ................................................................. B-3 vii
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Notes
viii
Chapter 1: Introduction
Chapter 1
Introduction
1-1 Overview
Checklist
Congratulations on purchasing your computer motherboard from an acknowledged leader in the industry. Supermicro boards are designed with the utmost attention to detail to provide you with the highest standards in quality and performance.
Please check that the following items have all been included with your motherboard.
If anything listed here is damaged or missing, contact your retailer.
•
One (1) H8DCT-HLN4F/HIBQF serverboard
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your motherboard.
•
Supermicro product manuals: http://www.supermicro.com/support/manuals/
•
Product drivers and utilities: ftp://ftp.supermicro.com
•
Product safety information: http://super-dev/about/policies/safety_information.cfm
•
If you have any questions, please contact our support team at:
[email protected]
1-1
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Headquarters
Address:
Tel:
Fax:
Email:
Web Site:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
+1 (408) 503-8000
+1 (408) 503-8008 [email protected] (General Information) [email protected] (Technical Support) www.supermicro.com
Europe
Address:
Tel:
Fax:
Email:
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
+31 (0) 73-6400390
+31 (0) 73-6416525 [email protected] (General Information) [email protected] (Technical Support) [email protected] (Customer Support) www.supermicro.com
Web Site:
Asia-Pacifi c
Address:
Tel:
Fax:
Email:
Tel:
Web Site:
Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
+886-(2) 8226-3990
+886-(2) 8226-3992 [email protected]
+886-(2)-8226-3990 www.supermicro.com.tw
1-2
Figure 1-1. H8DCT-HLN4F Image
Chapter 1: Introduction
1-3
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Figure 1-1. H8DCT-HIBQF Image
1-4
Chapter 1: Introduction
Figure 1-2. H8DCT-HLN4F/HIBQF Serverboard Layout
(not drawn to scale)
LE1
UID
JIB1
JI2C1 JPB1
LE2
LE3
KVM
DP1
BMC
InfiniBand
NIC
SPEAKER
DP2
AMD
SP5100
AMD
SR5670 or
SR5690
CPU1
CPU2
Notes:
Jumpers not indicated are for test purposes only.
Not all ports, jumpers or LED Indicators are available on all serverboards.
1-5
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Connector
GPU FAN 1
JIPMB1
IPMI LAN
JB1
JOH1
JTPM1
JP1
KVM
LAN1/2/3/4
UID
USB2/3
Jumper
JBT1
JIB1
JI2C1/JI2C2
JPB1
JPG1
JPL1
JWD1
LED
LAN Ports
Dedicated IPMI LAN
LE1
LE2
LE3
DP1
DP2
H8DCT-HLN4F/HIBQF Quick Reference
Description Default Setting
CMOS Clear (See Section 2-8)
Infi niBand Enable/Disable Pins 1-2 (Enabled)
I2C to PCI-E Slot Enable/Disable
BMC Enable/Disable
VGA Enable/Disable
LAN 1/2 Enable/Disable (LAN 1/2/3/4 for
H8DCT-HLN4F)
Watch Dog Enable/Disable
Open (Disabled)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Reset)
Description
LEDs for the LAN Ethernet ports
LEDs for the dedicated IPMI LAN Ethernet port
LED for UID Button
Infi niBand Physical Link LED (Green) (H8DCT-HIBQF only)
Infi niBand Logical Link LED (Yellow) (H8DCT-HIBQF only)
LED for IPMI activity
LED for Serverboard Power-On
Description
GPU Fan Header
System Management Bus Header (SMBus)
Dedicated IPMI LAN Port
Infi niBand Connector
Overheat Warning Header
Trusted Platform Module Header
SMC Proprietary Slot for Power, FP Control & SATA connectors
Keyboard/Video/Mouse Port
Gigabit Ethernet (RJ45) Ports
Unit Identifi er Button
Universal Serial Bus (USB) Ports, Headers
1-6
Chapter 1: Introduction
CPU
•
Dual AMD Opteron 4000 series (AMD Socket C32 type) processors
Note: Refer to our web site for details on supported processors.
Memory
•
Up to twelve (12) slots of single/dual-channel DIMMs supporting up to 192 GB of ECC RDIMM DDR3-1600/1333/1066 MHz speed SDRAM memory in
1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB size memory modules of 1.5V or
1.35V voltages.
Note: Refer to Section 2-5 before installing memory and our web site for recommended DIMMs.
Chipset
•
AMD SR5670 (H8DCT-HLN4F) or SR5690 (H8DCT-HIBQF) chipset and one
SP5100 Southbridge chipset
Expansion Slots
•
One (1) PCI-Express x16 Gen. 2
•
One (1) PCI-Express x8 Gen. 2 (in x4 slot; for adapter card)
BIOS
•
16 Mb AMIBIOS ® SPI Flash ROM
•
DMI 2.3, PCI 2.2, ACPI 1.0 (ACPI 2.0 is BIOS supported), SMBIOS 2.3, Real
Time Clock Wakeup, Plug and Play (PnP), BIOS resume hot keys, Hardware
BIOS Virus Protection
PC Health Monitoring
•
Onboard voltage monitors
•
Fan status monitor with fi rmware/software on/off and speed control
•
Watch Dog
•
Environmental temperature monitoring via BIOS
•
Power-up mode control for recovery from AC power loss
•
System resource alert (via included utility program)
•
Auto-switching voltage regulator for the CPU core
•
CPU thermal trip support
•
I
2
C temperature sensing logic
•
Chipkill Support
1-7
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
ACPI Features
•
Microsoft OnNow
•
Slow blinking LED for suspend state indicator
•
BIOS support for USB keyboard
Onboard I/O
•
Four (4) USB (Universal Serial Bus 2.0) ports (two via headers, two via KVM ports)
•
Up to four (4) LAN ports supported by one onboard Intel® i350 Ethernet controller for 10/100/1000Base-T (Four for the H8DCT-HLN4F or two for the H8DCT-HIBQF)
•
One (1) dedicated IPMI LAN port
•
One (1) KVM (VGA+COM+2*USB) port
•
One Mellanox Connect-X2 Infi niBand port supporting a single QSFP connector
(only for H8DCT-HIBQF)
Other
•
Onboard power LED
Utilities
•
BIOS fl ash upgrade utility
•
Super Doctor III
•
IPMI 1.5 / 2.0
Dimensions
•
Proprietary format: (LxW) 6.8" x 16.64" (173 x 423 mm)
1-8
Chapter 1: Introduction
Figure 1-3. AMD SR5670 or SR5690 and SP5100 Chipset:
System Block Diagram
Note: This is a general block diagram and may not exactly represent
the features on your serverboard. See the previous pages for the actual specifi cations of your serverboard.
RJ45
RJ45
RJ45
RJ45
CH 2
CH 1
DDR3
1600/1333/1066 MT/s
AMD
Socket C32
CPU2
HT3 Link
16 x16 bits 6.4GT/s
HT3 Link
16 x16 bits 6.4GT/s
CH 2
AMD
Socket C32
CPU1
CH 1
DDR3
1600/1333/1066 MT/s
HT3 Link
16x16 bits 5.2GT/s
INTEL
I350
PCI-E GEN2 X4
NCSI
A-Link
PCI-E GEN2 X16
PCI-E Slot1
SR5690 or
SR5670
PCI-E GEN2 X8
PCI-E Slot2
PCI-E GEN2 X8
Mellanox
Connect-X2
DDR2 SDRAM
64Mb X16bit
PSU I2C
IPMB
BMC
VGA
WPCM450-R
FE PHY
RTL8201N
HWM
W83795G
RJ45
PCI
SMBus
LPC
SIO
W83527
JKVM
VGA
COM
USB
SP5100
USB
Header
SPI Flash
SATA x6
Hot Plug
CONN
1-9
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
T h e H 8 D C T- H L N 4 F / H I B Q F s e r v e r b o a r d i s b a s e d o n t h e A M D
AMD SR5670 or SR5690 and SP5100 chipset. This chipset functions as a Media and Communications Processor (MCP). Controllers for the system memory are integrated directly into AMD Opteron processors.
AMD AMD SR5670 or SR5690 and SP5100 Chipset
The AMD AMD SR5670 or SR5690 and SP5100 chispsets are each a single-chip, high-performance HyperTransport peripheral controller. They include a 30 or 42lane PCI Express interface, an AMD Opteron 16-bit Hyper Transport interface link, a six-port Serial ATA interface and a four-port USB 2.0 interface. This hub connects directly to the CPU.
HyperTransport Technology
HyperTransport technology is a high-speed, low latency point to point link that was designed to increase the communication speed by a factor of up to 48x between integrated circuits. This is done partly by reducing the number of buses in the chipset to reduce bottlenecks and by enabling a more effi cient use of memory in multi-processor systems. The end result is a signifi cant increase in bandwidth within the chipset.
1-5 PC Health Monitoring
This section describes the PC health monitoring features of the H8DCT-HLN4F/HIBQF serverboard. The serverboard has an onboard System Hardware Monitor chip that supports PC health monitoring.
Onboard Voltage Monitors
The onboard voltage monitor will continuously scan crucial voltage levels. Once a voltage becomes unstable, it will give a warning or send an error message to the screen. Users can adjust the voltage thresholds to defi ne the sensitivity of the voltage monitor. Real time readings of these voltage levels are all displayed in BIOS.
Fan Status Monitor with Firmware/Software Speed Control
The PC health monitor can check the RPM status of the cooling fans. The onboard fans are controlled by thermal management via BIOS.
1-10
Chapter 1: Introduction
CPU Overheat/Fan Fail LED and Control
This feature is available when the user enables the CPU overheat/Fan Fail warning function in the BIOS. This allows the user to defi ne an overheat temperature. When this temperature is exceeded or when a fan failure occurs, the Overheat/Fan Fail warning LED is triggered.
Auto-Switching Voltage Regulator for the CPU Core
The 5-phase-switching voltage regulator for the CPU core can support up to
AMD Opteron 4000 series processors and auto-sense voltage IDs ranging from 0.8
V to 1.55V. This will allow the regulator to run cooler and thus make the system more stable.
This section describes the features of your motherboard that deal with power and power settings.
Microsoft OnNow
The OnNow design initiative is a comprehensive, system-wide approach to system and device power control. OnNow is a term for a PC that is always on but appears to be off and responds immediately to user or other requests.
Slow Blinking LED for Suspend-State Indicator
When the CPU goes into a suspend state, the chassis power LED will start blinking to indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will wake-up and the LED will automatically stop blinking and remain on.
BIOS Support for USB Keyboard
If a USB keyboard is the only keyboard in the system, it will function like a normal keyboard during system boot-up.
Note: To wake up the system from an S4 state by the USB keyboard/mouse, please
connect the keyboard/mouse to USB port 0/1 at the rear I/O side.
1-11
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Main Switch Override Mechanism
The power button can function as a system suspend button. When the user depresses the power button, the system will enter a SoftOff state. The monitor will be suspended and the hard drive will spin down. Depressing the power button again will cause the whole system to wake-up. During the SoftOff state, the power supply provides power to keep the required circuitry in the system alive. In case the system malfunctions and you want to turn off the power, just depress and hold the power button for 4 seconds. The power will turn off and no power will be provided to the motherboard.
As with all computer products, a stable power source is necessary for proper and reliable operation. It is even more important for processors that have high CPU clock rates.
The H8DCT-HLN4F/HIBQF serverboard requires the use of proprietary power supplies. Please refer to the pinout information for the power connectors in Section
7 of Chapter 2 for detailed information on power requirements.
In areas where noisy power transmission is present, you may choose to install a line fi lter to shield the computer from noise. It is recommended that you also install a power surge protector to help avoid problems caused by power surges.
Warning: To prevent the possibility of explosion, do not use the wrong type of
onboard CMOS battery or install it upside down.
The disk drive adapter functions of the Super I/O Winbond® BMC chip includes a data separator, write pre-compensation circuitry, decode logic, data rate selection, a clock generator, drive interface control logic and interrupt and DMA logic. The wide range of functions integrated onto the Super I/O greatly reduces the number of components required for interfacing with fl oppy disk drives.
The Super I/O provides two high-speed, 16550 compatible serial communication ports (UARTs), one of which supports serial infrared communication. Each UART includes a 16-byte send/receive FIFO, a programmable baud rate generator, complete modem control capability and a processor interrupt system. Both UARTs provide legacy speed with baud rate of up to 115.2 Kbps as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which support higher speed modems.
1-12
Chapter 1: Introduction
The Super I/O provides functions that comply with ACPI (Advanced Confi guration and Power Interface), which includes support of legacy and ACPI power management through a SMI or SCI function pin. It also features auto power management to reduce power consumption.
The IRQs, DMAs and I/O space resources of the Super I/O can be fl exibly adjusted to meet ISA PnP requirements, which support ACPI and APM (Advanced Power
Management).
1-13
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Notes
1-14
Chapter 2: Installation
Chapter 2
Installation
2-1 Standardized Warning Statements
About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury. Should you have questions or experience difficulty, contact Supermicro's Technical Support department for assistance. Only certifi ed technicians should attempt to install or confi gure components.
Read this section in its entirety before installing or confi guring components in the
Supermicro chassis.
These warnings may also be found on our web site at
http://www.supermicro.
com/about/policies/safety_information.cfm
.
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメー
って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。
2-1
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.
¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
Reemplazar la batería exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las baterías gastadas según las instrucciones del fabricante.
ףילחהל שי .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש
.
תצ למומ ןרצי תרבח
ץוציפ
!הרהזא
תנכס תמייק
מ םאותה גוסב הללוסה תא
.ןרציה תוארוה יפל עצבל שי תושמושמה תוללוסה קוליס
ﻚﻴﻠﻌﻓ ﺔﺤﻴﺤﺻ ﺮﻴﻏ ﺔﻘﻳﺮﻄﺑ ﺔﻳﺭﺎﻄﺒﻟﺍ ﻝﺍﺪﺒﺘﺳﺍ ﺔﻟﺎﺣ ﻲﻓ ﺭﺎﺠﻔﻧﺍ ﻦﻣ ﺮﻄﺧ ﻙﺎﻨﻫ
ﺔﻌﻨﺼﻤﻟﺍ ﺔﻛﺮﺸﻟﺍ ﻪﺑ ﺖﺻﻭﺃ ﺎﻤﻛ ﺎﻬﻟﺩﺎﻌﻳ ﺎﻣ ﻭﺃ
ﺔﻳﺭﺎﻄﺒﻟﺍ ﻝﺍﺪﺒﺘﺳﺍ
ﻉﻮﻨﻟﺍ ﺲﻔﻨﺑ ﻂﻘﻓ
ﺔﻌﻧﺎﺼﻟﺍ ﺔﻛﺮﺸﻟﺍ ﺕﺎﻤﻴﻠﻌﺘ ﻟ ﺎﻘﻓﻭ ﺔﻠﻤﻌﺘﺴﻤﻟﺍ ﺕﺎﻳﺭﺎﻄﺒﻟﺍ ﻦﻣ ﺺﻠﺨﺗ
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Waarschuwing
Er is ontploffi ngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd te worden.
2-2
Chapter 2: Installation
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws and regulations.
製品の廃棄
この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes erfolgen.
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
רצומה קוליס
.הנידמה יקוח
!הרהזא
ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס
ﺔﻴﻨﻁﻮﻟﺍ ﺢﺋﺍﻮﻠﻟﺍﻭ ﻦﻴﻧﺍﻮﻘﻟﺍ ﻊﻴﻤﺠ ﻟ ﺎﻘﻓﻭ ﻪﻌﻣ ﻞﻣﺎﻌﺘﻟﺍ ﻲﻐﺒﻨﻳ ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻦﻣ ﻲﺋﺎﻬﻨﻟﺍ ﺺﻠﺨﺘﻟﺍ
ﺪﻨﻋ
경고!
이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen.
2-3
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL damage to your system board, it is important to handle it very carefully. The following measures are generally suffi cient to protect your equipment from ESD.
Precautions
•
Use a grounded wrist strap designed to prevent static discharge.
•
Touch a grounded metal object before removing the board from the antistatic bag.
•
Handle the board by its edges only; do not touch its components, peripheral chips, memory modules or gold contacts.
•
When handling chips or modules, avoid touching their pins.
•
Put the motherboard and peripherals back into their antistatic bags when not in use.
•
For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the motherboard.
•
Use only the correct type of CMOS onboard battery as specifi ed by the manufacturer. Do not install the CMOS onboard battery upside down, which may result in a possible explosion.
Unpacking
The motherboard is shipped in antistatic packaging to avoid static damage. When unpacking the board, make sure the person handling it is static protected.
2-4
Chapter 2: Installation
2-3 Processor and Heatsink Installation
Caution: Exercise extreme caution when handling and installing the processor. Always
connect the power cord last and always remove it before adding, removing or changing any hardware components.
Installation Procedure
Follow the procedures as listed below to install the motherboard into a chassis.
1. Install the processor(s) and the heatsink(s).
2. Install the motherboard in the chassis.
3. Install the memory and add-on cards.
4. Finally, connect the cables and install the drivers.
Installing the Processors
1. Begin by removing the cover plate that protects the CPU. Lift the lever on the CPU socket until it points straight up. With the lever raised, lift open the silver CPU retention plate.
2. Use your thumb and your index fi nger to hold the CPU. Locate and align pin 1 of the CPU socket with pin 1 of the CPU. Both are marked with a triangle.
Triangles
2-5
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
3. Align pin 1 of the CPU with pin
1 of the socket. Once aligned, carefully place the CPU into the socket. Do not drop the CPU
on the socket, move the CPU horizontally or vertically or rub the
CPU against the socket or against any pins of the socket, which may damage the CPU and/or the
socket.
4. With the CPU inserted into the socket, inspect the four corners of the CPU to make sure that it is properly installed and fl ush with the socket. Then, gently lower the silver CPU retention plate into place.
Installing the Heatsinks
We recommend the use of active type heatsinks (except for 1U systems). Use any onboard fan header for the CPU's heatsink fan. To install the heatsink, please follow the installation instructions that are included with your heatsink package.
Note: Make sure the heatsink is placed so that the fi ns of the heatsink are in the
direction of the airfl ow in your system.
2-6
Chapter 2: Installation
2-4 Mounting the Serverboard into a Chassis
All motherboards have standard mounting holes to fi t different types of chassis.
Make sure that the locations of all the mounting holes for both the motherboard and the chassis match. Although a chassis may have both plastic and metal mounting fasteners, metal ones are highly recommended because they ground the motherboard to the chassis. Make sure that the metal standoffs click in or are screwed in tightly.
Check the Compatibility of the Serverboard Ports and the I/O Shield
1. The H8DCT-HLN4F/HIBQF serverboard requires a chassis that can support a board of (LxW) 6.8" x 16.64" (173 x 423 mm) in size.
2. Make sure that the I/O ports on the motherboard align with their respective holes in the I/O shield at the rear of the chassis.
Mounting the Serverboard onto the Tray in the Chassis
1. Carefully mount the motherboard onto the motherboard tray by aligning the motherboard mounting holes with the raised metal standoffs in the tray.
2. Insert screws into all the mounting holes in the motherboard that line up with the standoffs.
3. Then use a screwdriver to secure the motherboard to the mainboard tray - tighten until just snug (if too tight you might strip the threads). Metal screws provide an electrical contact to the motherboard ground to provide a continuous ground for the system.
Caution: Exercise extreme caution when installing or removing memory modules to
prevent any possible damage.
Installing Memory
1. Insert each memory module vertically into its slot, paying attention to the notch along the bottom of the module to prevent inserting the module incorrectly (see Figure 2-1).
2. Install to slots CPU1/DIMM1A, CPU1/DIMM2A, etc. Always install in groups of two and in the numerical order of the DIMM slots. See support information below.
3. Gently press down on the memory module until it snaps into place.
4. With two DIMMs installed, repeat step 2 to populate the CPU2 DIMM slots. Always install two DIMMs to both CPU DIMM slots for more effi cient operation.
2-7
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Note: 1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB size memory modules are
supported. It is highly recommended that you remove the power cord from the system before installing or changing memory modules. Please refer to our web site for memory that has been tested on the H8DCT-HLN4F/HIBQF serverboard.
Figure 2-1. Installing DIMM into Slot
To I n s t a l l : I n s e r t
module vertically and press down until it s n a p s i n t o p l a c e .
Pay attention to the alignment notch at the bottom.
Notch
To R e m o v e : U s e
your thumbs to gently
Release Tab
push the release tabs near both ends of the module. This should release it from the slot.
Front View
Notch
Note: Notch should align with the receptive key point on the slot.
Release Tab
Top View of DDR3 Slot
Memory Support
The H8DCT-HLN4F/HIBQF serverboard supports single/dual-channel,
DDR3-1600/1333/1066 MHz registered ECC/Unbuffered ECC/non-ECC SDRAM memory modules.
Populating two adjacent slots at a time with memory modules of the same size and type will result in interleaved (128-bit) memory, which is faster than non-interleaved
(64-bit) memory.
Maximum Memory
The H8DCT-HLN4F/HIBQF serverboard supports a maximum of up to 192 GB of
ECC RDIMM SDRAM memory in twelve (12) DIMM slots.
2-8
Chapter 2: Installation
# DIMMS
2 DIMMs
4 DIMMs
6 DIMMs
Memory Population for Optimal Performance
-For a Serverboard with One CPU (CPU1) Installed
CPU Channel 1 Channel 2
CPU1 P1-1A P1-2A
CPU1
CPU1
P1-1A
P1-1A P1-1B
P1-1C
P1-1C
P1-2A
P1-2A P1-2B
P1-2C
P1-2C
Memory Population for Optimal Performance
-For a Serverboard with Two CPUs (CPU1 & CPU2) Installed
# DIMMS CPU
CPU1 P1-1A
Channel 1
P1-2A
Channel 2
4 DIMMs
CPU2 P2-1A P2-2A
8 DIMMs
12 DIMMs
CPU1
CPU2
CPU1
CPU2
P1-1A
P2-1A
P1-1A
P2-1A
P1-1B
P2-1B
P1-1C
P2-1C
P1-1C
P2-1C
P1-2A
P2-2A
P1-2A
P2-2A
P1-2B
P2-2B
P1-2C
P2-2C
P1-2C
P2-2C
DIMM Module Population Confi guration
For memory to work properly, follow the tables below for memory installation:
DIMM Type
Unbuffered
DIMM
Registered
DIMM
Per Channel DIMM Populations Options
DIMM A DIMM B DIMM C
Max.
MHz, 1.5V
DIMMs
Max. MHz,
1.35V DIMMs
SR or DR Empty Empty 1600 MHz 1333 MHz
SR
DR
Empty
Empty
SR
DR
1333 MHz
1066 MHz
1333 MHz
1066 MHz
SR or DR
SR
SR
DR
Empty
DR
Empty
Empty
SR
Empty
QR
DR
Empty
SR
SR
DR
Empty
DR
1600 MHz
1333 MHz
1066 MHz
1066 MHz
1066 MHz
800 MHz
1333 MHz
1333 MHz
800 MHz
1066 MHz
800 MHz
800 MHz
Max. GB/
Channel
8 GB
8 GB
16 GB
16 GB
8 GB
12 GB
32 GB
32 GB
48 GB
Note 1: Due to OS limitations, some operating systems may not show more than
4 GB of memory.
Note 2: Due to memory allocation to system devices, the amount of memory that
remains available for operational use will be reduced when 4 GB of RAM is used.
The reduction in memory availability is disproportional.
2-9
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
2-6 PCI Expansion Cards
A riser card is used to support one standard size (full height full length) PCI expansion card.
Installing a PCI Expansion Card
1. Confi rm that you have the correct riser card for your chassis model and the add-on card includes a standard bracket.
2. Remove the chassis cover.
3. Install the riser card by sliding card into the appropriate slot in the serverboard.
4. Choose the PCI slot shield in which to place the add-on card.
5. In that slot, open the PCI slot shield lever and slide the shield sideways.
6. From inside the chassis, remove the PCI slot shield.
7. Slide the add-on card into the riser card and attach the add-on card bracket in place of the PCI slot shield.
8. Secure the add-on card by closing the PCI slot shield lever.
9. Connect cables to the add-on card as necessary.
2-10
Chapter 2: Installation
2-7 I/O Port and Control Panel Connections
The I/O ports are color coded to make setting up your system easier. See Figure
2-2 below for the colors and locations of the various I/O ports.
Figure 2-2. I/O Port Locations and Defi nitions
1 3
2 4
1. LAN3
(H8DCT-HLN4F Only)
2. LAN1
5 6
Rear I/O Ports
5. IPMI LAN 3. LAN4
(H8DCT-HLN4F Only)
4. LAN2 6. KVM
(VGA+COM+2*USB)
7
7. Infi niBand Port
(H8DCT-HIBQF Only)
8. UID
2-11
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Fan Header
This motherboard has one GPU fan header (GPU_Fan1). This 4-pin fans header is backward compatible with
3-pin fans. However, fan speed control is available for 4-pin fans only. The fan speeds are controlled by fi rmware thermal management via IPMI 2.0..
See the table on the right for pin defi nitions
3
4
1
2
Fan Header
Pin Defi nitions
Pin# Defi nition
Ground
+12V
Tachometer
PWR Modulation
LAN1/2/3/4 (Ethernet Ports)
Up to four Gigabit Ethernet ports
(designated LAN1, LAN2, LAN3 and
LAN4) are located on the rear of the serverboard. The H8DCT-HIBQF has two ports whereas the H8DCT-HLN4F has four. Additionally, there is a dedicated LAN for IPMI next to the four rear LAN ports. These Ethernet ports accept RJ45 type cables.
8
9
6
7
3
4
1
2
LAN Ports (LAN1/2/3/4)
Pin Defi nition
Pin# Defi nition Pin# Defi nition
P2V5SB
TD0+
10
11
SGND
Act LED
5
TD0-
TD1+
12
13
P3V3SB
TD114
Link 100 LED
(Yellow, +3V3SB)
Link 1000 LED
(Yellow, +3V3SB)
Ground TD2+
TD2-
15
16 Ground
Ground TD3+
TD3-
17
18 Ground
NC indicates no connection.
Unit Identifi er Button
In addition to the UID (Unit Identifi er) button on the rear I/O panel, there is another UID button located on the control panel. When you push either
UID button, both Rear UID and Front
Panel UID Indicators will illuminate.
Push either button again to turn off both indicators. These UID indicators provide easy identifi cation of a system unit that may be in need of service.
2
3
4
UID Button
Pin Defi nitions
Pin# Defi nition
1 Ground
Ground
Button In
Ground
2-12
Chapter 2: Installation
IPMB
A System Management Bus header for the IPMI slot is located at JIPMB1.
Connect the appropriate cable here to use the IPMB I2C connection on your system.
1
2
3
JIPMB1
Pin Defi nitions
Pin# Defi nition
Data
Ground
Clock
4 No Connection
Overheat LED
C o n n e c t a n L E D t o t h e J O H 1 header to provide warning of chassis overheating. See the table on the right for pin defi nitions.
1
2
Overheat LED
Pin Defi nitions
(JOH1)
Pin# Defi nition
3.3V
OH Active
USB Headers
Two USB 2.0 headers (USB2/3) are also included on the motherboard.
These may be connected to provide front side access. A USB cable (not included) is needed for the connection.
See the table on the right for pin defi nitions.
Universal Serial Bus Headers
Pin Defi nitions
(USB2/3)
JUSB1
Pin# Defi nition
1 +5V
3 PO-
Pin# Defi nition
2 +5V
4 PO-
5
7
PO+
Ground
6
8
PO+
Ground
9 Key 10 NC
Note: NC indicates no connection.
JP1 Adapter Card Connector
JP1 Adapter card connector slot provides front access to the power supply, serial ATA and Front Panel
Control connections for the H8DCT series motherboards. Plug an Adapter card into this connector to use the functions indicated above. This connector is designed specifi cally for a Supermicro-proprietary adapter card.
2-13
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Trusted Platform Module Header
The JTPM1 header is used to connect a Trusted Platform Module (TPM), available separately from a third-party vendor. A TPM is a security device that allows encryption and authentication of hard drives, disallowing access if the
TPM associated with it is not installed in the system. See the table on the right for pin defi nitions.
15
17
19
7
9
11
13
1
3
5
Trusted Platform Module
Header Pin Defi nitions (JTPM1)
Pin# Defi nition Pin# Defi nition
LCLK
LFRAME
LRESET
2
4
6
GND
No Pin
VCC5
LAD3
VCC3
LAD0
RSV0
SB3V
GND
LPCPD
8 LAD2
10 LAD1
12 GND
14 RSV1
16 SERIRQ
18 CLKRUN
20 RSV2
SXB1 Adapter Card Slot/Connector
A PCI-Express 2.0 x8 (in x4) slot
(SXB1) is located at JPCIE2 on the motherboard. This slot is used for an
SMC proprietary SAS adapter card.
2-14
Chapter 2: Installation
3 2 1
Connector
Pins
Explanation of Jumpers
To modify the operation of the motherboard, jumpers can be used to choose between optional settings.
Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identifi ed with a square solder pad on the printed circuit board. See the diagram at right for an example of jumping pins 1 and 2.
Refer to the motherboard layout page for jumper locations.
Note: On two-pin jumpers, "Closed"
means the jumper is on and "Open" means the jumper is off the pins.
Jumper
Setting
3 2 1
JBT1 contact pads
CMOS Clear
JBT1 is used to clear CMOS, which will also clear any passwords. Instead of pins, this jumper consists of contact pads to prevent accidentally clearing the contents of CMOS.
To Clear CMOS
1. First power down the system and unplug the power cord(s). It is also recommended that you remove the onboard battery from the serverboard.
2. With the power disconnected, short the CMOS pads with a metal object such as a small screwdriver.
3. Remove the screwdriver (or shorting device).
4. Reconnect the power cord(s) and power on the system.
Note 1. For an ATX power supply, you must completely shut down the system,
remove the AC power cord, and then short JBT1 to clear CMOS.
Note 2. Be sure to remove the onboard CMOS Battery before you short JBT1 to
clear CMOS.
Note 3. Clearing CMOS will also clear all passwords.
Note 4: Do not use the PW_ON connector to clear CMOS.
2-15
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
I2C to PCI-Express Slots
JI
2
C1/JI
2
C2 slots allows you to enable the I
2
C bus to communicate with a
PCI-Express slot. For the jumpers to work properly, please set both jumpers to the same setting. If enabled, both jumpers must be enabled. If disabled, both jumpers must be disabled. See the table on the right for jumper settings.
BMC Jumper
JPB1 is used to enable or disable theBMC (Baseboard Management
Control) Chip and the onboard IPMI connection.This jumper is used together with the IPMI settings in the
BIOS. The default position is on pins
1 and 2 to Enable BMC. See the table on the right for jumper settings.
VGA Enable/Disable
JPG1 allows you to enable or disable the VGA port. The default position is on pins 1 and 2 to enable VGA. See the table on the right for jumper settings.
I 2 C to PCI-Express Slot
Jumper Settings
(JI 2 C1/JI 2 C2)
Jumper Setting Defi nition
Closed Enabled
Open Disabled
BMC Jumper Enable (JPB1)
Jumper Settings
Jumper Setting Defi nition
Pins 1-2 Enabled (default)
Pins 2-3 Disabled
VGA Enable/Disable
Jumper Settings (JPG1)
Jumper Setting Defi nition
Pins 1-2
Pins 2-3
Enabled
Disabled
LAN Enable/Disable
Change the setting of jumper JPL1 to enable or disable the LAN1/2/3/4
Ethernet ports. See the table on the right for jumper settings. The default setting is enabled.
LAN Jumper Settings
(JPL1)
Jumper Setting Defi nition
Pins 1-2 Enabled
Pins 2-3 Disabled
Infi niBand Port Enable/Disable
JIB1 enables or disables the Infi niBand port on H8DCT-HIBQF serverboard.
The default position is on pins 1 and 2 to enable the port. See the table below for jumper settings.
2-16
Infi niBand Port
Jumper Enable (JIB1)
Jumper Settings
Jumper Setting Defi nition
Pins 1-2
Pins 2-3
Enabled
Disabled
Chapter 2: Installation
Watch Dog Enable/Disable
Watch Dog
Jumper Settings (JWD1)
JWD1 enables the Watch Dog function, a system monitor that takes action when a software application freezes the system. Jumping pins 1-2 will have
Jumper Setting Defi nition
Pins 1-2
Pins 2-3
Reset
NMI
WD reboot the system if a program
Open Disabled freezes. Jumping pins 2-3 will generate a non-maskable interrupt for the
Note: When Watch Dog is enabled, the user must write their own application software to disable the Watch Dog
Timer.
program that has frozen. See the table on the right for jumper settings. Watch
Dog must also be enabled in BIOS.
2-10 Onboard Indicators
LAN1/LAN2/LAN3/LAN4 LEDs
The Ethernet ports (located beside the
KVM port) have two LEDs. On each Gb
LAN port, one LED blinks to indicate activity while the other may be green, amber or off to indicate the speed of the connection. See the table on the right for the functions associated with the connection speed LED.
Link Speed
LED
GLAN LED
Activity
LED
GLAN Activity Indicator
(Right) LED Settings
Color Status Defi nition
Off
Yellow
No Connections
Flashing Active
LAN Connection Speed
Indicator (Left) LED Settings
LED Color Defi nition
Off
Green
Amber
10 MHz
100 MHz
1 GHz
Power LED
DP2 is an Onboard Power LED.
When this LED is lit, it means power is present on the serverboard. Be sure to turn off the system and unplug the power cord(s) before removing or installing components.
Power LED
(DP2)
State System Status
On
Off
Standby power present on motherboard
No power connected
2-17
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Dedicated IPMI LAN LEDs
A dedicated IPMI LAN is also included on the IPMI LAN port mounted on the serverboard. The amber LED on the right indicates activity, while the green
LED on the left indicates the speed of the connection. See the table at right for more information.
Link LED
IPMI LAN
Activity LED
IPMI LAN
Link/Speed LED (Left)
& Activity LED (Right)
Color Status Defi nition
Off Off No Connection
Green:
Solid
Amber
Blinking
Link/
Speed
(Left)
Activity
(Right)
100 Mb/s
Active
Infi niBand LED Indicators
Tw o I n f i n i B a n d L E D i n d i c a t o r s
(LE 2 / LE3) are loc ated near the
Infi niBand port of the H8DCT-HIBQF serverboard. The green LED (LE2) is the Infi niBand link LED while the yellow LED (LE3) indicates activity.
Refer to the tables at the right for details.
Infi niBand LED (LE2)
Activity LED
Color Status Defi nition
Green Solid Infi niBand Connected
Off Off No Connection
Infi niBand LED (LE3)
Activity LED
Color Status Defi nition
Yellow Solid
Yellow Dim
Off Off
Infi niBand Active
Infi niBand Connected,
Activity Idle
No Connection
IPMI LED
The serverboard contains an IPMI LED
(DP1) located near the corner above the PCI-E slots. When this LED is lit, it means a connection is active for the built-in IPMI on the serverboard.
Note: This LED is not installed on non-
IPMI boards.
IPMI LED (DP1)
State System Status
On Active connection
Off No connection
2-18
UID LED (LE1)
A rear UID LED Indicator, located at LE1, works in conjunction with the rear UID switch to provide easy identifi cation for a unit that might be in need of service. Refer to Page 2-12 for further UID details.
Chapter 2: Installation
2-19
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
2-11 Enabling SATA RAID
Now that the hardware is set up, you must install the operating system and the
SATA RAID drivers, if you wish to use RAID with your SATA drives. The installation procedure differs depending on whether you wish to have the operating system installed on a RAID array or on a separate non-RAID drive. See the instructions below for details.
Serial ATA (SATA)
Serial ATA (SATA) is a physical storage interface that employs a single cable with a minimum of four wires to create a point-to-point connection between devices. This connection is a serial link that supports a SATA transfer rate from 150 MBps. The serial cables used in SATA are thinner than the traditional cables used in Parallel
ATA (PATA) and can extend up to one meter in length, compared to only 40 cm for
PATA cables. Overall, SATA provides better functionality than PATA.
Installing the OS/SATA Driver
Before installing the OS (operating system) and SATA RAID driver, you must decide if you wish to have the operating system installed as part of a bootable RAID array or installed to a separate non-RAID hard drive. If on a separate drive, you may install the driver either during or after the OS installation. If you wish to have the
OS on a SATA RAID array, you must follow the procedure below and install the driver during the OS installation.
Building a Driver Diskette
You must fi rst build a driver diskette from Supermicro drivers for your system.
Drivers can be found at ftp://ftp.supermicro.com
. (You will have to create this disk on a computer that is already running and with the OS installed.)
Building a Driver Diskette
1. Install your system drives from the FTP website. A display as shown in Figure
2-7 will appear.
2. Click on the icon labeled “Build Driver Diskettes and Manuals” and follow the instructions to create a fl oppy disk with the drivers on it.
3. Once it’s been created, remove the fl oppy and insert the installation CD for the Windows Operating System you wish to install into the CD-ROM drive of the new system you are about to confi gure.
Note: You need to have an external USB fl oppy when building the driver diskette.
Window’s Vista, Windows 2008 or later Windows OS systems can use a USB stick instead of a fl oppy.
2-20
Chapter 2: Installation
Enabling SATA RAID in the BIOS
Before installing the Windows operating system, you must change some settings in the BIOS. Boot up the system and hit the <Delete> key to enter the BIOS Setup
Utlility. After the setup utility loads,
1. Use the arrow keys to move to the "Exit" menu. Scroll down using the arrow keys to "Load Optimal Defaults" and press <Enter>. Select "OK" to confi rm, then <Enter> to load the default settings.
2. Use the arrow keys to move to the "Advanced" menu, then scroll down to
"IDE confi guration". On this submenu, scroll down to "OnChip SATA Type" and choose the "RAID" option (Figure 2-4). “RAID Codebase” submenu appears. This setting allows you to select the codebase for your RAID setup.
Options are either Adaptec or DotHill.
Figure 2-4. BIOS Setup Screen
3. Press the <Esc> key twice and scroll to the "Exit" menu. Select "Save
Changes and Exit" and press <Enter>, then press <Enter> again to verify.
4. After exiting the BIOS Setup Utility, the system reboots. When prompted during the startup, to use the DotHilll RAID Utility program press the
<CTRL+R> key (Figure 2-5), or to use the Adaptec RAID Utility program press the <CTRL+A> key (Figure 2-6).
2-21
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Figure 2-5. DotHill RAID Utility Program Screen
Figure 2-6.Adaptec RAID Utility Program Screen
2-22
Chapter 2: Installation
Using the DotHill and Adaptec RAID Utility
The RAID Utility program allows you to defi ne the drives you want to include in the
RAID array and the mode and type of RAID.
Installing the RAID Driver During OS Installation
You may also use the procedure below to install the RAID driver during the Windows
OS installation:
1. With the Windows OS installation CD-ROM in the CD drive, restart the system.
2. Press <Enter> again to continue with the Windows setup.
3. When you see the prompt, hit the <F6> key to enter Windows setup.
4. Eventually a blue screen will appear with a message that begins “Windows could not determine the type of one or more storage devices . . .” When you see the screen, hit the <S> key to “Specify Additional Device”, then insert the driver diskette you just created into the fl oppy drive.
5. Highlight “Manufuacturer Supplied Hardware Support Disk” and hit the
<Enter> key.
6. Highlight the fi rst “Adaptec RAID” driver shown and press the <Enter> key to install it.
2-23
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
2-12 Installing Drivers
The Supermicro Website contains drivers and utilities for your system at ftp://ftp.
supermicro.com
, some of which must be installed, such as the chipset driver. After downloading and installing the drivers and utilities, the display shown in Figure 2-7 should appear.
Click the icons showing a hand writing on paper to view the readme fi les for each item. Click the computer icons to the right of these items to install each item (from top to the bottom) one at a time. After installing each item, you should reboot the system before moving on to the next item on the list. The bottom icon with a CD on it allows you to view the entire contents of the utilities.
Figure 2-7. Driver/Tool Installation Display Screen
2-24
Chapter 2: Installation
Supero Doctor III
The SuperDoctor® III program is a Web base management tool that supports remote management capability. It includes Remote and Local Management tools. The local management is called SD III Client. The SuperDoctor III program included on the
CD-ROM that came with your motherboard allows you to monitor the environment and operations of your system. SuperDoctor III displays crucial system information such as CPU temperature, system voltages and fan status. See the Figure below for a display of the SuperDoctor III interface.
Note: The default User Name and Password for SuperDoctor III is ADMIN / ADMIN.
Note: When SuperDoctor is fi rst installed, it adopts the temperature threshold settings that have been set in BIOS. Any subsequent changes to these thresholds must be made within SuperDoctor, as the SuperDoctor settings override the BIOS settings. To set the BIOS temperature threshold settings again, you would fi rst need to uninstall SuperDoctor.
Figure 2-8. Supero Doctor III Interface Display Screen (Health Information)
2-25
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Figure 2-9. Supero Doctor III Interface Display Screen (Remote Control)
Note: The SuperDoctor III program and User’s Manual can be downloaded from the
Supermicro web site at http://www.supermicro.com/products/accessories/software/
SuperDoctorIII.cfm
.For Linux, we recommend that you use the SuperoDoctor II application instead.
2-26
Chapter 2: Installation
2-13 Serverboard Battery
Caution: There is a danger of explosion if the onboard battery is installed upside
down, which will reverse its polarites (see Figure 2-10). This battery must be replaced only with the same or an equivalent type recommended by the manufacturer
(CR2032). Dispose of used batteries according to the manufacturer's instructions.
Figure 2-10. Installing the Onboard Battery
OR
Please handle used batteries carefully. Do not damage the battery in any way; a damaged battery may release hazardous materials into the environment. Do not discard a used battery in the garbage or a public landfi ll. Please comply with the regulations set up by your local hazardous waste management agency to dispose of your used battery properly.
2-27
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Notes
2-28
Chapter 3
Troubleshooting
Chapter 3: Troubleshooting
Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘Technical Support
Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter.
Always disconnect the AC power cord before adding, changing or installing any hardware components.
Before Power On
1. Check that the onboard power LED is lit (DP2 on the motherboard).
2. Make sure that the power connector is connected to your power supply.
3. Make sure that no short circuits exist between the motherboard and chassis.
4. Disconnect all cables from the motherboard, including those for the keyboard and mouse.
5. Remove all add-on cards.
6. Install a CPU and heatsink (making sure it is fully seated) and connect the internal (chassis) speaker and the power LED to the motherboard. Check all jumper settings as well.
7. Use the correct type of onboard CMOS battery (CR2032) as recommended by the manufacturer. To avoid possible explosion, do not install the CMOS battery upside down.
No Power
1. Make sure that no short circuits exist between the motherboard and the chassis.
2. Verify that all jumpers are set to their default positions.
3. Check that the 115V/230V switch on the power supply is properly set.
4. Turn the power switch on and off to test the system.
5. The battery on your motherboard may be old. Check to verify that it still supplies ~3VDC. If it does not, replace it with a new one.
3-1
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
No Video
1. If the power is on but you have no video, remove all the add-on cards and cables.
2. Use the speaker to determine if any beep codes exist. Refer to Appendix A for details on beep codes.
Note: If you are a system integrator, VAR or OEM, a POST diagnostics card is
recommended. For I/O port 80h codes, refer to App. B.
Memory Errors
1. Make sure that the DIMM modules are properly and fully installed.
2. You should be using proper ECC DDR-3 memory (see next page). Also, it is recommended that you use the same memory type and speed for all DIMMs in the system. See Section 2-5 for memory details.
3. Check for bad DIMM modules or slots by swapping modules between slots and noting the results.
4. Check the power supply voltage 115V/230V switch.
Losing the System’s Setup Confi guration
1. Make sure that you are using a high quality power supply. A poor quality power supply may cause the system to lose the CMOS setup information.
Refer to Section 1-6 for details on recommended power supplies.
2. The battery on your motherboard may be old. Check to verify that it still supplies ~3VDC. If it does not, replace it with a new one.
3. If the above steps do not fi x the setup confi guration problem, contact your vendor for repairs.
3-2 Technical Support Procedures
Before contacting Technical Support, please take the following steps. Also, note that as a motherboard manufacturer, we do not sell directly to end-users, so it is best to fi rst check with your distributor or reseller for troubleshooting services. They should know of any possible problem(s) with the specifi c system confi guration that was sold to you.
1. Please review the ‘Troubleshooting Procedures’ and 'Frequently Asked
Questions' (FAQs) sections in this chapter or see the FAQs on our web site before contacting Technical Support.
3-2
Chapter 3: Troubleshooting
2. BIOS upgrades can be downloaded from our web site.
Note: Not all BIOS can be fl ashed depending on the modifi cations to the boot
block code.
3. If you still cannot resolve the problem, include the following information when contacting us for technical support:
•
Serverboard model and PCB revision number
•
BIOS release date/version (this can be seen on the initial display when your system fi rst boots up)
•
System confi guration
An example of a Technical Support form is posted on our web site.
Distributors: For immediate assistance, please have your account number ready when contacting our technical support department by e-mail.
Question: What type of memory does my motherboard support?
Answer: The H8DCT-HLN4F/HIBQF serverboard supports up to a maximum
of up to 192 GB of ECC RDIMM, DDR3-1600/1333/1066 MHz speed,
1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB size SDRAM memory in twelve (12) slots. See Section 2-4 for details on installing memory.
Question: How do I update my BIOS?
Answer: It is recommended that you not upgrade your BIOS if you are not
experiencing problems with your system. Updated BIOS fi les are located on our web site. Please check our BIOS warning message and the information on how to update your BIOS on our web site. Also, check the current BIOS revision and make sure it is newer than your current BIOS before downloading.
Select your motherboard model on the web page and download the corresponding
BIOS fi le to your computer. Unzip the BIOS update fi le, in which you will fi nd the readme.txt (fl ash instructions), the afudos.exe (BIOS fl ash utility) and the BIOS image (xxx.rom) fi les. Copy these fi les to a bootable fl oppy disk, insert the disk into drive A and reboot the system. At the DOS prompt after rebooting, enter the command "fl ash" (without quotation marks) then type in the BIOS fi le that you want to update with (xxxx.rom).
Question: What's on the CD that came with my motherboard?
Answer: The supplied compact disc has quite a few drivers and programs that will
greatly enhance your system. We recommend that you review the CD and install the applications you need. Applications on the CD include chipset drivers for Windows and security and audio drivers.
3-3
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Question: Why can't I turn off the power using the momentary power on/off switch?
Answer: The instant power off function is controlled in BIOS by the Power Button
Mode setting. When the On/Off feature is enabled, the motherboard will have instant off capabilities as long as the BIOS has control of the system. When the Standby or Suspend feature is enabled or when the BIOS is not in control such as during memory count (the fi rst screen that appears when the system is turned on), the momentary on/off switch must be held for more than four seconds to shut down the system. This feature is required to implement the ACPI features on the motherboard.
3-4 Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required before any warranty service will be rendered. You can obtain service by calling your vendor for a Returned Merchandise Authorization (RMA) number. When returning to the manufacturer, the RMA number should be prominently displayed on the outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and handling charges will be applied for all orders that must be mailed when service is complete.
For faster service, RMA authorizations may be requested online ( http://www.supermicro.com/support/rma/ ).
This warranty only covers normal consumer use and does not cover damages incurred in shipping or from failure due to the alteration, misuse, abuse or improper maintenance of products.
During the warranty period, contact your distributor fi rst for any product problems.
3-4
Chapter 4: BIOS
Chapter 4
BIOS
4-1 Introduction
This chapter describes the AMIBIOS™ Setup utility for the H8DCT-HLN4F/HIBQF serverboard. The 16 Mb AMI BIOS® is stored in a fl ash chip and can be easily upgraded using a fl oppy disk-based program.
Note: Due to periodic changes to the BIOS, some settings may have been added
or deleted and might not yet be recorded in this manual. Please refer to the Manual
Download area of our web site for any changes to BIOS that may not be refl ected in this manual.
Starting the Setup Utility
To enter the BIOS Setup Utility, hit the <Delete> key while the system is booting-up.
(In most cases, the <Delete> key is used to invoke the BIOS setup screen. There are a few cases when other keys are used, such as <F1>, <F2>, etc.) Each main
BIOS menu option is described in this manual.
The Main BIOS screen has two main frames. The left frame displays all the options that can be confi gured. “Grayed-out” options cannot be confi gured. The right frame displays the key legend. Above the key legend is an area reserved for a text message. When an option is selected in the left frame, it is highlighted in white. Often a text message will accompany it. (Note that BIOS has default text messages built in. We retain the option to include, omit, or change any of these text messages.)
Settings printed in Bold are the default values.
A "
" indicates a submenu. Highlighting such an item and pressing the <Enter> key will open the list of settings within that submenu.
The BIOS setup utility uses a key-based navigation system called hot keys. Most of these hot keys (<F1>, <F10>, <Enter>, <ESC>, <Arrow> keys, etc.) can be used at any time during the setup navigation process.
4-1
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
When you fi rst enter AMI BIOS Setup Utility, you will see the Main Menu screen.
You can always return to the Main Menu by selecting the Main tab on the top of the screen with the arrow keys.
The Main Menu screen provides you with a system overview, which includes the version, built date and ID of the AMIBIOS, the type, speed and number of the processors in the system and the amount of memory installed in the system.
System Time/System Date
You can edit this fi eld to change the system time and date. Highlight System Time or System Date using the <Arrow> keys. Enter new values through the keyboard.
Press the <Tab> key or the <Arrow> keys to move between fi elds. The date must be entered in DAY/MM/DD/YYYY format. The time is entered in HH:MM:SS format.
Please note that time is in a 24-hour format. For example, 5:30 A.M. appears as
05:30:00 and 5:30 P.M. as 17:30:00.
4-3 Advanced Settings Menu
Boot Feature
Quick Boot
If Enabled, this option will skip certain tests during POST to reduce the time needed for the system to boot up. The options are Enabled and Disabled.
Quiet Boot
If Disabled, normal POST messages will be displayed on boot-up. If Enabled, this display the OEM logo instead of POST messages.
Add On ROM Display Mode
This option sets the display mode for Option ROM. The options are Force BIOS or Keep Current.
Bootup Num Lock
This option selects the power-on state for the NUM lock to either On or Off.
4-2
Chapter 4: BIOS
Wait for F1 if Error
This setting controls the system response when an error is detected during the boot sequence. When enabled, BIOS will stop the boot sequence when an error is detected, at which point you will need to press the F1 button to re-enter the
BIOS setup menu. The options are Enabled and Disabled.
Hit 'DEL' Message Display
Use this option to Enable or Disable the "Press DEL to run setup" message in
POST.
Interrupt 19 Capture
Select Enabled to allow ROMs to trap Interrupt 19. The options are Enabled and Disabled.
Watch Dog Function
Allows system to restart when system is inactive more than 5-minutes. The options are Enabled and Disabled.
Power Button Function
This sets the function of the power button when you turn off the system. Options include 4-second Overide and Instant Off.
Restore on AC Power Loss
This sets the action that occurs when an AC power loss occurs. Options include
Power Off, Power On and Last State.
Resume on RTC Alarm
This setting allows you to enable or disable RTC to generate a wake event for
S4/S5 or Legacy Soft Off. Options are Enabled and Disabled.
Processor and Clock Options
CPU Confi guration
This displays static information on the Module Version, Physical Count and
Logical Count for the system's processor(s) and clock.
CPU Information
The information for the installed processor includes Revision, Cache L1/L2/L3,
Speed, NB CLK, Able to Change Frequency and uCode Patch Level.
4-3
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
GART Error Reporting
This option should remain disabled for normal operation. The driver developer may enable this option for testing purposes. Options are Enabled or Disabled.
Microcode Update
This setting Enables or Disables microcode updating.
Secure Virtual Machine Mode
This setting is used to Enable or Disable SVM.
Power Now
This setting is used to Enable or Disable the AMD Power Now feature.
Power Cap
This option can decide the highest P-state in the OS. Options include P-state
0 through P-state 4.
CPU Down Core Mode
This option sets down core support for the CPU. Options include Disabled, 1
Core through n Cores in odd numbered increments. The value n is depend on the core per CPU node.
Advanced Chipset Control
NorthBridge Confi guration
Memory Confi guration
Bank Interleaving
Select Auto to automatically enable a bank-interleaving memory scheme when this function is supported by the processor. The options are Auto and Disabled.
Node Interleaving
This option enables node memory interleaving. Options include Auto or
Disabled.
4-4
Chapter 4: BIOS
Channel Interleaving
This option enables channel memory interleaving. Options include Auto or Disabled.
CS Sparing
This setting will reserve a spare memory rank in each node when enabled.
Options are Enabled and Disabled.
Bank Swizzle Mode
This setting Enables or Disables the bank swizzle mode.
ECC Confi guration
ECC Mode
This submenu affects the DRAM scrub rate based on its setting. Options include Disabled, Basic, Good, Super, Max and User. Selecting User activates the other options for user setting.
DRAM ECC Enable
This setting allows hardware to report and correct memory errors automatically, maintaining system integrity. Options are Enabled or
Disabled. This is option is only active if ECC Mode above is set to User.
DRAM Timing Confi guration
DRAM Timing Confi g
This option allows you to set the DRAM timing confi guration for the system.
Options include Auto or Manual.
Memory Clock Speed
This options sets the memory clock speed. Options include 200 Mhz,
266 Mhz, 333 Mhz, 400 Mhz, 533 Mhz, 667 Mhz, 800 Mhz and 933 Mhz.
HT Speed Support
Use this option to select the HT Link Frequency. Options include HT1 or
Auto. Note that a Cold Reset is needed after changing this option's setting.
IOMMU
This setting is used to enable or disable or set the GART size in systems without AGP. Options include Enabled and Disabled.
4-5
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
SouthBridge Confi guration
OHCI/EHCI HC Device Functions
These settings allow you to either Enable or Disable functions for OHCI or EHCI bus devices.
USB 2.0 Controller Mode
Use this setting to confi gure the USB 2.0 Controller in either Hi-Speed (480
Mps) or Full Speed (12 Mps) mode. Options include Enabled (Hi-Speed Mode) or Disabled (Full Speed Mode).
Legacy USB Support
Select "Enabled" to enable the support for USB Legacy. Disable Legacy support if there are no USB devices installed in the system. "Auto" disabled Legacy support if no USB devices are connected. The options are Disabled, Enabled and Auto.
IDE Confi guration
OnChip SATA Channel
This setting allows you to Enable or Disable the OnChip SATA channel.
OnChip SATA Type
U s e t hi s se tti n g to s et t he On Chi p S ATA typ e. Opt i ons i nc l ud e
Native IDE, RAID, AMD_AHCI and Legacy IDE.
RAID Codebase
This submenu appears when you choose "RAID" from the "OnChip SATA
Type" setting above. This setting allows you to select the codebase for using your RAID setup. Options are either Adaptec or DotHill.
SATA IDE Combined Mode
This setting allows you to Enable or Disable the SATA IDE combined mode.
PATA Channel Confi guration
This allows you to set PATA channel confi guration. Options include SATA as
Primary or SATA as secondary.
4-6
Chapter 4: BIOS
Primary/Secondary/Third/Fourth IDE Master/Slave
LBA/Large Mode
LBA (Logical Block Addressing) is a method of addressing data on a disk drive. The options are Disabled and Auto.
Block (Multi-Sector Transfer)
Block mode boosts IDE drive performance by increasing the amount of data transferred. Only 512 bytes of data can be transferred per interrupt if block mode is not used. Block mode allows transfers of up to 64 KB per interrupt.
Select "Disabled" to allow the data to be transferred from and to the device one sector at a time. Select "Auto" to allows the data transfer from and to the device occur multiple sectors at a time if the device supports it. The options are Auto and Disabled.
PIO Mode
PIO (Programmable I/O) mode programs timing cycles between the IDE drive and the programmable IDE controller. As the PIO mode increases, the cycle time decreases.
The options are Auto, 0, 1, 2, 3, and 4. Select Auto to allow BIOS to auto detect the PIO mode. Use this value if the IDE disk drive support cannot be determined. Select 0 to allow BIOS to use PIO mode 0, which has a data transfer rate of 3.3 MBs. Select 1 to allow BIOS to use PIO mode 1, which has a data transfer rate of 5.2 MBs. Select 2 to allow BIOS to use PIO mode 2, which has a data transfer rate of 8.3 MBs. Select 3 to allow BIOS to use PIO mode 3, which has a data transfer rate of 11.1 MBs. Select 4 to allow BIOS to use PIO mode 4, which has a data transfer rate of 16.6 MBs. This setting generally works with all hard disk drives manufactured after 1999. For other disk drives, such as IDE CD-ROM drives, check the specifi cations of the drive.
DMA Mode
Selects the DMA Mode. Options are Auto, SWDMA0, SWDMA1, SWDMA2,
MWDMA0. MDWDMA1, MWDMA2, UDMA0. UDMA1, UDMA2, UDMA3,
UDMA4 and UDMA5. (SWDMA=Single Word DMA, MWDMA=Multi Word
DMA, UDMA=UltraDMA.)
4-7
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
S.M.A.R.T.
Self-Monitoring Analysis and Reporting Technology (SMART) can help predict impending drive failures. Select "Auto" to allow BIOS to auto detect hard disk drive support. Select "Disabled" to prevent AMI BIOS from using the S.M.A.R.T. Select "Enabled" to allow AMI BIOS to use the S.M.A.R.T. to support hard drive disk. The options are Disabled, Enabled, and Auto.
32-Bit Data Transfer
Select "Enabled" to activate the function of 32-Bit data transfer. Select
"Disabled" to deactivate the function. The options are Enabled and Disabled.
IDE Detect Timeout (Sec)
Use the +/- keys to adjust and select the time out for detecting ATA/ATAPI devices. The default value is 35.
PCI/PnP Confi guration
Clear NVRAM
Select Yes to clear NVRAM during boot-up. The options are Yes and No.
Plug & Play O/S
Select Yes to allow the OS to confi gure Plug & Play devices. (This is not required for system boot if your system has an OS that supports Plug & Play.) Select No to allow AMIBIOS to confi gure all devices in the system.
PCI Latency Timer
This option sets the latency of all PCI devices on the PCI bus. Select a value to set the PCI latency in PCI clock cycles. Options are 32, 64, 96, 128, 160,
192, 224 and 248.
PCI IDE Busmaster
Use this setting to Enable or Disable BIOS enabled uses of PCI Busmastering for reading or writing to IDE drives.
ROM Scan Ordering
This setting determines which kind of option ROM activates prior to another.
Options include Onboard First and Addon First.
PCIe Slot 1 Riser
This setting allows you to optimize your PCIe Slot 1 riser to either 1x16, 2x8 or Auto.
4-8
Chapter 4: BIOS
PCIe x16 Slot 1
These settings Enable or Disable the specifi ed PCIe slot in your system.
PCIe x8 Slot 2
These settings Enable or Disable the specifi ed PCIe slot in your system.
Onboard LAN Option ROM Select
This setting allows you to select the onboard LAN option ROM for iSCSI or PXE.
Note: You must enable ONLY LAN1 when the iSCSI support option is specifi ed.
Load Onboard LAN 1 Option ROM
This option allows you to enable or disable the onboard LAN 1 option ROM.
Load Onboard LAN 2 Option ROM
This option allows you to enable or disable the onboard LAN 2 option ROM.
Boots Graphic Adapter Priority
This option specifi es the priority for booting the graphic adapter for Onboard
VGA or Offboard VGA.
SuperIO Device Confi guration
Serial 1 Address
This option specifi es the base I/O port address and Interrupt Request address of serial port 1. Select "Disabled" to prevent the serial port from accessing any system resources. When this option is set to Disabled, the serial port physically becomes unavailable. Select "3F8/IRQ4" to allow the serial port to use 3F8 as its
I/O port address and IRQ 4 for the interrupt address. Options include Disabled,
3F8/IRQ4, 3E8/IRQ4 and 2E8/IRQ3
Serial 2 Address
This option specifi es the base I/O port address and Interrupt Request address of serial port 2. Select "Disabled" to prevent the serial port from accessing any system resources. When this option is set to "Disabled", the serial port physically becomes unavailable. Select "2F8/IRQ3" to allow the serial port to use 2F8 as its
I/O port address and IRQ 3 for the interrupt address. Options include Disabled,
2F8/IRQ3, 3E8/IRQ4 and 2F8/IRQ3.
Serial Port 2 Attribute
This option allows you to set COM2 as a normal serial port or as virtual COM for SOL. Options are SOL or COM.
4-9
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Remote Access Confi guration
Remote Access
Use this option to Enable or Disable Remote Access in your system. If enabled, the settings below will appear.
Serial Port Number
Use this setting to select the serial port for console redirection. Options include
COM1, COM2*. The displayed base address and IRQ for the serial port changes to refl ect the selection you make.
Note: Make sure the selected port is enabled.
Serial Port Mode
Selects the serial port settings to use. Options are (115200 8, n, 1), (57600 8, n, 1), (38400 8, n, 1), (19200 8, n, 1) and (09600 8, n, 1).
Flow Control
Selects the fl ow control to be used for console redirection. Options are None,
Hardware and Software.
Redirection After BIOS POST
Options are Disable (no redirection after BIOS POST), Boot Loader (redirection during POST and during boot loader) and Always (redirection always active).
Note that some OS's may not work with this set to Always.
Terminal Type
Selects the type of the target terminal. Options are ANSI, VT100 and VT-UTF8.
VT-UTF8 Combo Key Support
Allows you to Enable or Disable VT-UTF8 combination key support for ANSI/
VT100 terminals.
Sredir Memory Display Delay
Use this setting to set the delay in seconds to display memory information.
Options are No Delay, 1 sec, 2 secs and 4 secs.
4-10
Chapter 4: BIOS
Hardware Health Confi guration
CPU Overheat Alarm
This setting allows you to specify the type of alarm for CPU overheating. Options include The Early Alarm and The Default Alarm.
Fan Speed Control Modes
This feature allows the user to determine how the system will control the speed of the onboard fans. The options are Full Speed/FS (Max Cooling), Performance/
PF (Better Cooling), Balanced/BL (Balance between performance and energy saving), Energy Saving/ES (Lower Power and Noise).
Other items in the submenu are systems monitor displays for the following information:
CPU 1 Temperature, CPU 2 Temperature, System Temperature, Fan 1-2
Reading, CPU 1 VCore, CPU 2 VCore, CPU 1 Mem VTT, CPU 2 Mem VTT,
CPU 1 Mem, CPU 2 Mem, 1.1V, 1.8V, 5V, +12V, 3.3 Vcc, 3.3 VSB, VBAT and HT Voltage.
CPU Temperature Display (CTD)
CPU Temperature descriptions are defi ned as:
Low
[Tctl Value = Lowest Value, Tctl Value = -45]
Medium
[Tctl Value = -46, Tctl Value = 60]
High
[Tctl Value = -61 and Above]
Note: Only CPU temperature (Low, Medium, High) and system temperature (RT1) are required to be displayed in BIOS and in-system monitoring software. Other
Serverboard components such as memory, chipset, SAS and 10Gb controllers, and others are not requried to display temperatures. For debugging and testing purposes, BIOS and system monitoring software can show motherboard components’ temperatures (such as memory, chipset, SAS and 10Gb controllers).
However for SMCI standard release version BIOS and system monitoring software, motherboard components’ temperatures are NOT required to be displayed.
CPU Overheating Alarm (COA)
CPU Overheating Alarm (COA) has “ Early Alarm ” and “ Default Alarm ” (default) options in the BIOS, and is required to be implemented in all fan speed control modes.
The Early Alarm is enabled when the Tctl value = 65, and is disabled when the Tctl value drops from 65 to 62.
4-11
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
The Default Alarm (default setting) is enabled when the Tctl value = 70, and is disabled when the Tctl value drops from 70 to 67.
When COA (either Early or Default Alarm) is enabled, the following actions are required to be executed:
•
System overheating LED is required to be ON and to solid red.
•
Onboard buzzer or speaker is required to be ON and to be a continuous sound.
•
All system fans are required to be operated at full speed.
•
System monitoring software (such as Super Doctor and IPMI if available) is required to report and record CPU overheating events in the event logs.
When COA (either Early or Default Alarm) is disabled, the following actions are required to be executed:
•
System overheating LED is required to be OFF.
•
Onboard buzzer or speaker is required to be OFF.
•
All system fans are required to be returned to a normal, non-CPU-overheating
LFSC condition.
Condition
Front Panel Overheating LED
Onboard Buzzer or Speaker
System Fan Speed Controls
BMC
BMC Event Log
Super Doctor
Super Doctor Event Log
When a CPU is overheating
On and Solid Red
On and Continuous Sound
Full Speed
Report PROCHOT
Record PROCHOT
Report PROCHOT
Record PROCHOT
ACPI Confi guration
ACPI Aware O/S
This setting Enables or Disables ACPI support for the system's operating system.
Options include Yes (enabled) or No (disabled).
ACPI APIC Support
Determines whether to include the ACPI APIC table pointer in the RSDT pointer list. The available options are Enabled and Disabled.
Headless Mode
Use this setting to Enable or Disable headless operation mode through ACPI.
4-12
Chapter 4: BIOS
ACPI Version Features
Use this setting the determine which ACPI version to use. Options are ACPI v1.0, ACPI v2.0 and ACPI v3.0.
NUMA Support
This setting allows you to enable or disable the building of an ACPI SRAT table.
WHEA Support
This setting allows you to enable or disable Windows Hardware Error Architecture.
IPMI Confi guration
This menu shows static information about the IPMI fi rmware revision and status of the BMC, as well as options for IPMI confi guration.
View BMC System Event Log
Pressing the Enter key will open the following settings. Use the "+" and "-" keys to navigate through the system event log.
Clear BMC System Event Log
Selecting this and pressing the Enter key will clear the BMC system event log.
Set LAN Confi guration
Use the "+" and "-" keys to choose the desired channel number. This displays
Channel Number and Channel Number Status information.
This menu contains options for inputing settings for the SET LAN Confi guration
Command. See IPMI 1.5 Specifi cation, table 11.1 for details. Use the "+" and
"-" keys to choose the desired channel number.
Note: Each question in this group may take a considerable amount of time.
IP Address Source
Select the source of this machine's IP address. If Static is selected, you will need to know and enter manually the IP address of this machine below.
If DHCP is selected, the BIOS will search for a DHCP (Dynamic Host
Confi guration Protocol) server in the network it is attached to, and request the next available IP address. The options are DHCP and Static.
The following items are assigned IP addresses automatically if DHCP is selected under IP Address Source above:
4-13
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
IP Address
This submenu sets the IP address source as either Static or DHCP. Selecting
Static allows you to manually set the IP Address, Subnet Mask and Gateway
Address.
In the fi eld provided here enter the IP address in the decimal form of xxx.xxx.
xxx.xxx with xxx having a value of less than 256 and in decimal form only The
IP address and current IP address in the BMC are shown.
Subnet Mask
In the fi eld provided here enter the Subnet address in the decimal form of xxx.xxx.xxx.xxx with xxx having a value of less than 256 and in decimal form only. The current subnet address in the BMC is shown.
Gateway Address
In the fi eld provided here enter the Gateway address in the decimal form of xxx.xxx.xxx.xxx with xxx having a value of less than 256 and in decimal form only. The current Gateway address in the BMC is shown.
MAC Address
In the fi eld provided here enter the MAC address in the hex form of xx.xx.xx.xx.
xx.xx with xx in hex form only. The current MAC address in the BMC is shown.
Event Log Confi guration
View Event Log
Pressing the Enter key will open the event log. Use the "
" and "" keys to navigate through the system event log.
Mark All Events as Read
Selecting this and pressing the Enter key marks all events as read in the event log.
Clear Event Log
Selecting this and pressing the Enter key clears the system event log.
SR56x0 (RD890S) PCIE Error Log
This setting allows you set an error log ofr PCIE errors. Options include Yes or No.
4-14
Chapter 4: BIOS
AMI BIOS provides a Supervisor and a User password. If you use both passwords, the Supervisor password must be set fi rst.
Change Supervisor Password
Select this option and press <Enter> to access the sub menu, and then type in the password.
Change User Password
Select this option and press <Enter> to access the sub menu, and then type in the password.
Boot Sector Virus Protection
This option is near the bottom of the Security Setup screen. Select "Disabled" to deactivate the Boot Sector Virus Protection. Select "Enabled" to enable boot sector protection. When "Enabled", AMI BIOS displays a warning when any program (or virus) issues a Disk Format command or attempts to write to the boot sector of the hard disk drive. The options are Enabled and Disabled.
4-15
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
The Boot Menu is accessible only when the "Load Onboard LAN Option ROM" setting (in the PCI/PnP Confi guration menu) is enabled.
Boot Device Priority
This feature allows you to prioritize the boot sequence from the list of available devices. A device that is in parenthesis has been disabled in the corresponding type menu.
Removable Drives
This feature allows you to specify the boot sequence from the list of available CD/
DVD drives. A device that is in parenthesis has been disabled in the corresponding type menu.
Hard Disk Drives
This feature allows you to specify the boot sequence from the list of available hard disk drives. A device that is in parenthesis has been disabled in the corresponding type menu.
CD/DVD Drives
This feature allows you to specify the boot sequence from the list of available CD/
DVD drives. A device that is in parenthesis has been disabled in the corresponding type menu.
USB Drives
This feature allows you to specify the boot sequence from the list of available USB drives. A device that is in parenthesis has been disabled in the corresponding type menu.
Network Drives
This feature allows you to specify the boot sequence from the list of available
Network drives. A device that is in parenthesis has been disabled in the corresponding type menu.
4-16
Chapter 4: BIOS
Retry Boot Devices
This option allows you to retry boot devices. Options include Enabled and Disabled.
Select the Exit tab from AMI BIOS Setup Utility screen to enter the Exit BIOS Setup screen.
Save Changes and Exit
When you have completed the system confi guration changes, select this option to leave BIOS Setup and reboot the computer, so the new system confi guration parameters can take effect. Select Save Changes and Exit from the Exit menu and press <Enter>.
Discard Changes and Exit
Select this option to quit BIOS Setup without making any permanent changes to the system confi guration and reboot the computer. Select Discard Changes and Exit from the Exit menu and press <Enter>.
Discard Changes
Select this option and press <Enter> to discard all the changes and return to AMI
BIOS Utility Program.
Load Optimal Defaults
To set this feature, select Load Optimal Defaults from the Exit menu and press
<Enter>. Then Select "OK" to allow BIOS to automatically load the Optimal Defaults as the BIOS Settings. The Optimal settings are designed for maximum system performance, but may not work best for all computer applications.
Load Fail-Safe Defaults
To set this feature, select Load Fail-Safe Defaults from the Exit menu and press
<Enter>. The Fail-Safe settings are designed for maximum system stability, but not maximum performance.
4-17
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Notes
4-18
Appendix A: BIOS Error Beep Codes
Appendix A
BIOS Error Beep Codes
During the POST (Power-On Self-Test) routines, which are performed each time the system is powered on, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to continue the
boot-up process. The error messages normally appear on the screen.
Fatal errors are those which will not allow the system to continue the boot-up
procedure. If a fatal error occurs, you should consult with your system manufacturer for possible repairs.
These fatal errors are usually communicated through a series of audible beeps. The numbers on the fatal error list (on the following page) correspond to the number of beeps for the corresponding error. All errors listed, with the exception of Beep
Code 8, are fatal errors.
A-1 AMIBIOS Error Beep Codes
Beep Code
1 beep
5 shorts, 1 long beep
1 long, 8 short
Error Message
Refresh
Memory error
Video error
Description
Circuits have been reset (Ready to power up)
No memory detected in system
Video adapter disabled or missing
A-1
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Notes
A-2
Appendix B: BIOS POST Checkpoint Codes
Appendix B
BIOS POST Checkpoint Codes
When AMIBIOS performs the Power On Self Test, it writes checkpoint codes to I/O port 0080h. If the computer cannot complete the boot process, diagnostic equipment can be attached to the computer to read I/O port 0080h.
B-1 Uncompressed Initialization Codes
The uncompressed initialization checkpoint codes are listed in order of execution:
Checkpoint Code Description
D0h The NMI is disabled. Power on delay is starting. Next, the initialization code checksum will be verifi ed.
D1h
D3h
Initializing the DMA controller, performing the keyboard controller BAT test, starting memory refresh and entering 4 GB fl at mode next.
Starting memory sizing next.
D4h
D5h
D6h
Returning to real mode. Executing any OEM patches and setting the Stack next.
Passing control to the uncompressed code in shadow RAM at E000:0000h. The initialization code is copied to segment 0 and control will be transferred to segment 0.
Control is in segment 0. Next, checking if <Ctrl> <Home> was pressed and verifying the system
BIOS checksum. If either <Ctrl> <Home> was pressed or the system BIOS checksum is bad, next will go to checkpoint code E0h. Otherwise, going to checkpoint code D7h.
B-1
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
B-2 Bootblock Recovery Codes
The bootblock recovery checkpoint codes are listed in order of execution:
F3h
F4h
F5h
FBh
FCh
FDh
FFh
Edh
Eeh
Efh
F0h
F1h
F2h
Checkpoint Code Description
E0h The onboard fl oppy controller if available is initialized. Next, beginning the base 512 KB memory test.
E1h Initializing the interrupt vector table next.
E2h
E6h
Initializing the DMA and Interrupt controllers next.
Enabling the fl oppy drive controller and Timer IRQs. Enabling internal cache memory.
Initializing the fl oppy drive.
Looking for a fl oppy diskette in drive A:. Reading the fi rst sector of the diskette.
A read error occurred while reading the fl oppy drive in drive A:.
Next, searching for the AMIBOOT.ROM fi le in the root directory.
The AMIBOOT.ROM fi le is not in the root directory.
Next, reading and analyzing the fl oppy diskette FAT to fi nd the clusters occupied by the
AMIBOOT.ROM fi le.
Next, reading the AMIBOOT.ROM fi le, cluster by cluster.
The AMIBOOT.ROM fi le is not the correct size.
Next, disabling internal cache memory.
Next, detecting the type of fl ash ROM.
Next, erasing the fl ash ROM.
Next, programming the fl ash ROM.
Flash ROM programming was successful. Next, restarting the system BIOS.
B-2
Appendix B: BIOS POST Checkpoint Codes
B-3 Uncompressed Initialization Codes
The following runtime checkpoint codes are listed in order of execution.
These codes are uncompressed in F0000h shadow RAM.
12h
13h
14h
19h
1Ah
2Bh
Checkpoint Code Description
03h The NMI is disabled. Next, checking for a soft reset or a power on condition.
05h
06h
The BIOS stack has been built. Next, disabling cache memory.
Uncompressing the POST code next.
07h
08h
0Ah
0Bh
0Ch
0Eh
0Fh
10h
11h
2Ch
2Dh
23h
24h
25h
27h
28h
Next, initializing the CPU and the CPU data area.
The CMOS checksum calculation is done next.
The CMOS checksum calculation is done. Initializing the CMOS status register for date and time next.
The CMOS status register is initialized. Next, performing any required initialization before the keyboard BAT command is issued.
The keyboard controller input buffer is free. Next, issuing the BAT command to the keyboard controller.
The keyboard controller BAT command result has been verifi ed. Next, performing any necessary initialization after the keyboard controller BAT command test.
The initialization after the keyboard controller BAT command test is done. The keyboard command byte is written next.
The keyboard controller command byte is written. Next, issuing the Pin 23 and 24 blocking and unblocking command.
Next, checking if <End or <Ins> keys were pressed during power on. Initializing CMOS RAM if the Initialize CMOS RAM in every boot AMIBIOS POST option was set in AMIBCP or the
<End> key was pressed.
Next, disabling DMA controllers 1 and 2 and interrupt controllers 1 and 2.
The video display has been disabled. Port B has been initialized. Next, initializing the chipset.
The 8254 timer test will begin next.
Next, programming the fl ash ROM.
The memory refresh line is toggling. Checking the 15 second on/off time next.
Passing control to the video ROM to perform any required confi guration before the video ROM test.
All necessary processing before passing control to the video ROM is done. Looking for the video ROM next and passing control to it.
The video ROM has returned control to BIOS POST. Performing any required processing after the video ROM had control
Reading the 8042 input port and disabling the MEGAKEY Green PC feature next. Making the
BIOS code segment writable and performing any necessary confi guration before initializing the interrupt vectors.
The confi guration required before interrupt vector initialization has completed. Interrupt vector initialization is about to begin.
Interrupt vector initialization is done. Clearing the password if the POST DIAG switch is on.
Any initialization before setting video mode will be done next.
Initialization before setting the video mode is complete. Confi guring the monochrome mode and color mode settings next.
B-3
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
3Ah
3Bh
40h
42h
43h
44h
Checkpoint Code Description
2Ah
2Eh
2Fh
Bus initialization system, static, output devices will be done next, if present. See the last page for additional information.
Completed post-video ROM test processing. If the EGA/VGA controller is not found, performing the display memory read/write test next.
The EGA/VGA controller was not found. The display memory read/write test is about to begin.
30h The display memory read/write test passed. Look for retrace checking next.
31h
32h
34h
37h
38h
39h
45h
46h
47h
48h
49h
4Bh
4Ch
4Dh
4Eh
4Fh
50h
51h
The display memory read/write test or retrace checking failed. Performing the alternate display memory read/write test next.
The alternate display memory read/write test passed. Looking for alternate display retrace checking next.
Video display checking is over. Setting the display mode next.
The display mode is set. Displaying the power on message next.
Initializing the bus input, IPL, general devices next, if present. See the last page of this chapter for additional information.
Displaying bus initialization error messages. See the last page of this chapter for additional information.
The new cursor position has been read and saved. Displaying the Hit <DEL> message next.
The Hit <DEL> message is displayed. The protected mode memory test is about to start.
Preparing the descriptor tables next.
The descriptor tables are prepared. Entering protected mode for the memory test next.
Entered protected mode. Enabling interrupts for diagnostics mode next.
Interrupts enabled if the diagnostics switch is on. Initializing data to check memory wraparound at 0:0 next.
Data initialized. Checking for memory wraparound at 0:0 and fi nding the total system memory size next.
The memory wraparound test is done. Memory size calculation has been done. Writing patterns to test memory next.
The memory pattern has been written to extended memory. Writing patterns to the base 640
KB memory next.
Patterns written in base memory. Determining the amount of memory below 1 MB next.
The amount of memory below 1 MB has been found and verifi ed.
The amount of memory above 1 MB has been found and verifi ed. Checking for a soft reset and clearing the memory below 1 MB for the soft reset next. If this is a power on situation, going to checkpoint 4Eh next.
The memory below 1 MB has been cleared via a soft reset. Clearing the memory above 1 MB next.
The memory above 1 MB has been cleared via a soft reset. Saving the memory size next.
Going to checkpoint 52h next.
The memory test started, but not as the result of a soft reset. Displaying the fi rst 64 KB memory size next.
The memory size display has started. The display is updated during the memory test.
Performing the sequential and random memory test next.
The memory below 1 MB has been tested and initialized. Adjusting the displayed memory size for relocation and shadowing next.
The memory size display was adjusted for relocation and shadowing.
B-4
Appendix B: BIOS POST Checkpoint Codes
8Ch
8Dh
8Fh
91h
95h
Checkpoint Code Description
52h
53h
The memory above 1 MB has been tested and initialized. Saving the memory size information next.
The memory size information and the CPU registers are saved. Entering real mode next.
54h
57h
58h
59h
60h
62h
65h
66h
Shutdown was successful. The CPU is in real mode. Disabling the Gate A20 line, parity, and the NMI next.
The A20 address line, parity, and the NMI are disabled. Adjusting the memory size depending on relocation and shadowing next.
The memory size was adjusted for relocation and shadowing. Clearing the Hit <DEL> message next.
The Hit <DEL> message is cleared. The <WAIT...> message is displayed. Starting the DMA and interrupt controller test next.
The DMA page register test passed. Performing the DMA Controller 1 base register test next.
The DMA controller 1 base register test passed. Performing the DMA controller 2 base register test next.
The DMA controller 2 base register test passed. Programming DMA controllers 1 and 2 next.
Completed programming DMA controllers 1 and 2. Initializing the 8259 interrupt controller next.
67h
7Fh
80h
81h
82h
83h
84h
85h
86h
87h
88h
89h
96h
Completed 8259 interrupt controller initialization.
Extended NMI source enabling is in progress.
The keyboard test has started. Clearing the output buffer and checking for stuck keys. Issuing the keyboard reset command next.
A keyboard reset error or stuck key was found. Issuing the keyboard controller interface test command next.
The keyboard controller interface test completed. Writing the command byte and initializing the circular buffer next.
The command byte was written and global data initialization has completed. Checking for a locked key next.
Locked key checking is over. Checking for a memory size mismatch with CMOS RAM data next.
The memory size check is done. Displaying a soft error and checking for a password or bypassing WINBIOS Setup next.
The password was checked. Performing any required programming before WINBIOS Setup next.
The programming before WINBIOS Setup has completed. Uncompressing the WINBIOS Setup code and executing the AMIBIOS Setup or WINBIOS Setup utility next.
Returned from WINBIOS Setup and cleared the screen. Performing any necessary programming after WINBIOS Setup next.
The programming after WINBIOS Setup has completed. Displaying the power on screen message next.
Programming the WINBIOS Setup options next.
The WINBIOS Setup options are programmed. Resetting the hard disk controller next.
The hard disk controller has been reset. Confi guring the fl oppy drive controller next.
The fl oppy drive controller has been confi gured. Confi guring the hard disk drive controller next.
Initializing the bus option ROMs from C800 next. See the last page of this chapter for additional information.
Initializing before passing control to the adaptor ROM at C800.
B-5
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Abh
B0h
B1h
00h
A2h
A3h
A4h
A5h
Checkpoint Code Description
97h
98h
99h
9Ah
Initialization before the C800 adaptor ROM gains control has completed. The adaptor ROM check is next.
The adaptor ROM had control and has now returned control to BIOS POST. Performing any required processing after the option ROM returned control.
Any initialization required after the option ROM test has completed. Confi guring the timer data area and printer base address next.
Set the timer and printer base addresses. Setting the RS-232 base address next.
9Bh
9Ch
9Dh
Returned after setting the RS-232 base address. Performing any required initialization before the Coprocessor test next.
Required initialization before the Coprocessor test is over. Initializing the Coprocessor next.
Coprocessor initialized. Performing any required initialization after the Coprocessor test next.
9Eh
A7h
A8h
A9h
Aah
Initialization after the Coprocessor test is complete. Checking the extended keyboard, keyboard
ID, and Num Lock key next. Issuing the keyboard ID command next.
Displaying any soft errors next.
The soft error display has completed. Setting the keyboard typematic rate next.
The keyboard typematic rate is set. Programming the memory wait states next.
Memory wait state programming is over. Clearing the screen and enabling parity and the NMI next.
NMI and parity enabled. Performing any initialization required before passing control to the adaptor ROM at E000 next.
Initialization before passing control to the adaptor ROM at E000h completed. Passing control to the adaptor ROM at E000h next.
Returned from adaptor ROM at E000h control. Performing any initialization required after the
E000 option ROM had control next.
Initialization after E000 option ROM control has completed. Displaying the system confi guration next.
Uncompressing the DMI data and executing DMI POST initialization next.
The system confi guration is displayed.
Copying any code to specifi c areas.
Code copying to specifi c areas is done. Passing control to INT 19h boot loader next.
B-6
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 34 Checklist
- 34 AMD AMD SR5670 or SR5690 and SP5100 Chipset
- 34 HyperTransport Technology
- 34 PC Health Monitoring
- 35 Standardized Warning Statements
- 35 About Standardized Warning Statements
- 35 Precautions
- 35 Unpacking
- 35 Processor and Heatsink Installation
- 35 Mounting the Serverboard into a Chassis
- 35 Memory Support
- 35 Maximum Memory
- 35 DIMM Module Population Confi guration
- 35 PCI Expansion Cards
- 35 I/O Port and Control Panel Connections
- 35 Fan Header
- 35 LAN1/2/3/4 (Ethernet Ports)
- 35 Unit Identifi er Button
- 35 Overheat LED
- 35 USB Headers
- 35 JP1 Adapter Card Connector
- 35 Trusted Platform Module Header
- 38 SXB1 Adapter Card Slot/Connector
- 38 Explanation of Jumpers
- 38 CMOS Clear
- 38 I2C to PCI-Express Slots
- 38 BMC Jumper
- 38 VGA Enable/Disable
- 38 LAN Enable/Disable
- 38 Infi niBand Port Enable/Disable
- 38 Watch Dog Enable/Disable
- 38 LAN1/LAN2/LAN3/LAN4 LEDs
- 38 Power LED
- 38 Dedicated IPMI LAN LEDs
- 38 Infi niBand LED Indicators
- 38 IPMI LED
- 38 UID LED (LE1)
- 38 2-11 Enabling SATA RAID
- 38 Serial ATA (SATA)
- 38 Installing the OS/SATA Driver
- 38 Building a Driver Diskette
- 38 Enabling SATA RAID in the BIOS
- 38 Using the DotHill and Adaptec RAID Utility
- 38 Installing the RAID Driver During OS Installation
- 38 Supero Doctor III
- 39 Before Power On
- 39 No Power
- 39 No Video
- 39 Memory Errors
- 39 Losing the System’s Setup Confi guration
- 39 Technical Support Procedures