advertisement
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 1
OWNER’S
MANUAL
COLOR TV/DVD/VCR TRIPLE COMBO
6720FDD
(20 inch)
POWER VOLUME SKIP PLAY SKIP
SEARCH
STOP OPEN/CLOSE
DVD
SELECT
TV/VCR
CHANNEL REC/OTR REW PLAY F.FWD
STOP
EJECT
HEADPHONE VIDEO L AUDIO R
This Owner’s Manual is made of recycled paper.
SUPPLIED ACCESSORIES
ACCESSORIES
Remote Control Unit
Batteries
Owner’s Manual
PART NO.
NE209UD
2 AA Batteries
0EMN02252
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
As an E
NERGY
S
TAR
Partner, our company has determined that this product meets the E
NERGY
S
TAR
guidelines for energy efficiency. E
NERGY
S
TAR
is a U.S. registered mark.
If you need additional operating assistance after reading this owner’s manual or to order replacement accessories, please call
TOLL FREE : 1-800-968-3429.
Or visit our WEB SITE at
http://www.funai-corp.com
Please read before using this equipment
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 2
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSON-
NEL.
The caution marking is located on the rear of the cabinet.
THIS SYMBOL INDICATES THAT DAN-
GEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE
APPLIANCE.
IMPORTANT SAFEGUARDS
1.Read instructions-All the safety and operating instructions should be read before the appliance is operated.
2.Retain Instructions-The safety and operating instructions should be retained for future reference.
3.Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to.
4.Follow Instructions-All operating and use instructions should be followed.
5.Cleaning-Unplug TV/DVD/VCR from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.
6.Attachments-Do not use attachments not recommended by the TV/DVD/VCR manufacturer as they may cause hazards.
7.Water and Moisture-Do not use this TV/DVD/VCR near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8.Accessories-Do not place this TV/DVD/VCR on an unstable cart, stand, tripod, bracket, or table. The TV/DVD/VCR may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the
TV/DVD/VCR. Any mounting of
PORTABLE CART WARNING the appliance should follow the manufacturer’s instructions and should use a mounting accessory recommended by the manufacturer.
An appliance and cart combination should be moved with care.Quick
stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
S3126A
- 2 -
AMEUBLES- Cet appareil ne doit
être placé que sur un meuble (avec ou sans roulettes) recommandé par le fabricant. Si vous l’installez sur un meuble à roulettes, déplacez les deux ensembles avec précaution.
Un arrêt brusque, l’utilisation d’une force excessive et des surfaces irrégulières risquent de déstabiliser l’ensemble et de le renverser.
SYMBOLE D'AVERTISSEMENT POUR
LES COMPOSANTES
APPAREIL ET MEUBLE A ROULETTES
S3126A
9. Ventilation-Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV/DVD/VCR and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the
TV/DVD/VCR on a bed, sofa, rug, or other similar surface.
This TV/DVD/VCR should never be placed near or over a radiator or heat register. This TV/DVD/VCR should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
10.Power Sources-This TV/DVD/VCR should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TV/DVD/VCRs intended to operate from battery power, or other sources, refer to the operating instructions.
11.Grounding or Polarization-This TV/DVD/VCR is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12.Power-Cord Protection-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
EN
1B15
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 3
F IGUR E A
EXAMPLE OF ANTENNA GROUNDING AS PER
NA TIONA L ELECT RIC AL CODE
AN TE NN A
L E A D I N
W I R E
GROUN D
C L A M P
A NTEN NA
DI S CHA RG E UN I T
(NEC SE CTI ON 8 10 -2 0)
E L E CT RI C
S E RV I CE
E Q U I P M E N T
S 2 8 9 8 A
NE C - NA TI O NAL EL E CTRI CAL CO DE
G RO UNDI NG CO NDUCT ORS
(NEC SE CTI ON 8 10 -2 1)
G RO UND CL AM PS
P OWE R S E RVI C E G RO UNDI NG
E L E C TR O DE S Y S T E M
(NEC A RT 2 50 , P ART H)
13.Outdoor Antenna grounding-If an outside antenna or cable system is connected to the TV/DVD/VCR, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)
14.Lightning-For added protection for this TV/DVD/VCR receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the TV/DVD/VCR due to lightning and power-line surges.
15.Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
16.Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind into this TV/DVD/VCR through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV/DVD/VCR.
18.Servicing-Do not attempt to service this TV/DVD/VCR yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19.Damage Requiring Service-Unplug this TV/DVD/VCR from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/DVD/VCR.
c. If the TV/DVD/VCR has been exposed to rain or water.
d. If the TV/DVD/VCR does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV/DVD/VCR to its normal operation.
e. If the TV/DVD/VCR has been dropped or damaged in any way.
f. When the TV/DVD/VCR exhibits a distinct change in performance-this indicates a need for service.
20.Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.
21.Safety Check-Upon completion of any service or repairs to this TV/DVD/VCR, ask the service technician to perform routine safety checks to determine that the TV/DVD/VCR is in proper operating condition.
22.Heat-This TV/DVD/VCR product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
- 3 EN
1B15
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 4
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly is prohibited.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
PRECAUTIONS
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUST-
MENTS OR PERFORMANCE OF PROCE-
DURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC
ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU’AU FOND.
- 4 EN
1B15
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 5
LOCATION
For safe operation and satisfactory performance of your TV/DVD/VCR, keep the following in mind when selecting a place for its installation:
•
Shield it from direct sunlight and keep it away from sources of intense heat.
•
Avoid dusty or humid places.
•
Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.
•
Install unit in a horizontal position.
•
Avoid locations subject to strong vibration.
•
Do not place the TV/DVD/VCR near strong magnetic fields.
•
Avoid moving TV/DVD/VCR to locations where temperature differences are extreme.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
•
Do not handle the power cord with wet hands.
•
Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.
•
If, by accident, water is spilled on your unit, unplug the power cord immediately and take the unit to our
Authorized Service Center for servicing.
•
Do not put your fingers or objects into the
TV/DVD/VCR disc loading tray.
•
Do not place anything directly on top of the unit.
WARNING
Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. If a DVD is played in a TV/DVD/
VCR which has moisture, it may damage the DVD and TV/DVD/VCR. Therefore when the condensation occurs inside the unit, turn the POWER on and allow at least 2 hours for the unit to dry out.
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some headings and notes in this manual, with the following meanings
TV/VCR
: Description refers to TV/VCR operation (in the
TV/VCR mode).
DVD-V
: Description refers to playback of DVD video discs
(in the DVD mode).
CD
: Description refers to playback of audio CDs
(in the DVD mode).
MP3
: Description refers to playback of MP3 discs
(in the DVD mode).
QUICK
: Description refers to the items to be set by the
QUICK mode (in the DVD mode).
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
The serial number of this product may be found on the back of the unit. No other TV/DVD/VCR has the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
- 5 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 6
C
IMPORTANT SAFEGUARDS . . .2, 3
C
PRECAUTIONS . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . .5
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE .5
WARNING . . . . . . . . . . . . . . . . . . . .5
SYMBOLS USED IN THIS
MANUAL . . . . . . . . . . . . . . . . . . . . .5
C
TABLE OF CONTENTS . . . . . . . . . .6
C
FEATURES . . . . . . . . . . . . . . . . . .7, 8
C
OPERATING CONTROLS AND
FUNCTIONS . . . . . . . . . . . . . . . .9, 10
C
PREPARATION FOR USE . . . . . . .11
ANTENNA/CABLE
CONNECTION . . . . . . . . . . . . . . . .11
CONNECTING TO EXTERNAL
INPUT JACKS . . . . . . . . . . . . . . . .12
INSTALLING THE BATTERIES . .12
EXTERNAL INPUT MODE . . . . . .12
CONNECTING TO A STEREO
SYSTEM . . . . . . . . . . . . . . . . . . . .13
CONNECTING TO A STEREO
AMPLIFIER EQUIPPED WITH DIGI-
TAL INPUT JACKS SUCH AS MD
DECK OR DAT DECK (for DVD) .13
CONNECTING TO A DOLBY
DIGITAL DECODER (for DVD) . .14
TV/VCR SECTION
C
SET UP FOR USE . . . . . . . . . . . . .15
CHANNEL SET UP
FOR THE FIRST TIME . . . . . . . . .15
DELETING (OR ADDING)
CHANNEL . . . . . . . . . . . . . . . . . . .15
CHANNEL SET UP AGAIN . . . . . .16
SELECTING THE LANGUAGE . .16
DAYLIGHT-SAVING TIME . . . . . .16
CLOCK SET UP
(AUTO / MANUAL) . . . . . . . . .17, 18
C
TV OPERATION . . . . . . . . . . . . . . .19
WATCHING A TV PROGRAM . . .19
DEGAUSSING . . . . . . . . . . . . . . . .19
PICTURE CONTROL . . . . . . . . . . .19
CLOSED CAPTION SYSTEM . . . .20
V-CHIP SET UP . . . . . . . . . . . .21, 22
C
MTS(Multi-Channel Television sound)SYSTEM . . . . . . . . . . . . . . . .23
CHECKING THE SELECTED
MTS MODE . . . . . . . . . . . . . . . . . .23
MTS RECORDING/MONITOR
MODE . . . . . . . . . . . . . . . . . . . . . .23
SELECTING THE MTS SYSTEM .24
C
VIDEO CASSETTE . . . . . . . . . . . . .25
TABLE OF CONTENTS
C
PLAYBACK . . . . . . . . . . . . . . . . . . .26
NORMAL PLAYBACK . . . . . . . . .26
TRACKING ADJUSTMENT . . . . .26
SLOW MOTION . . . . . . . . . . . . . .26
PICTURE SEARCH . . . . . . . . . . . .26
STILL PICTURE . . . . . . . . . . . . . .26
VERTICAL HOLD CONTROL . . .26
C
SPECIAL PLAYBACK . . . . . . . . . .27
RENTAL PLAYBACK . . . . . . . . . .27
AUTO REPEAT PLAYBACK . . . . .27
C
SEARCH . . . . . . . . . . . . . . . . . . . . .28
ZERO RETURN . . . . . . . . . . . . . . .28
TIME SEARCH . . . . . . . . . . . . . . .28
INDEX SEARCH . . . . . . . . . . . . . .29
C
SPECIAL FEATURES . . . . . . . . . .29
REAL TIME TAPE COUNTER . . .29
AUTO REWIND-EJECT . . . . . . . .29
C
RECORDING . . . . . . . . . . . . . . . . .30
NORMAL RECORDING . . . . . . . .30
SKIPPING UNWANTED SCENES
DURING
RECORDING . . . . . . . . . . . . . . . . .30
OTR (One Touch Recording) . . . . . .31
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder) . . .31
C
TIMER . . . . . . . . . . . . . . . . . . . . . .32
AUTOMATIC
TIMER RECORDING . . . . . . . . . .32
TIMER PROGRAM EXTENSION .33
HINTS FOR AUTOMATIC TIMER
RECORDING . . . . . . . . . . . . . . . . .34
AUTO RETURN . . . . . . . . . . . . . . .34
SLEEP TIMER . . . . . . . . . . . . . . . .34
C
ON SCREEN DISPLAY . . . . . . . . .35
C
CABLE CHANNEL
DESIGNATIONS . . . . . . . . . . . . . .35
DVD SECTION
SLOW FORWARD / SLOW
REVERSE . . . . . . . . . . . . . . . . . . . .38
ZOOM . . . . . . . . . . . . . . . . . . . . . .38
C
SEARCH FUNCTION . . . . . . . . . . .39
TRACK SEARCH . . . . . . . . . . . . .39
TITLE / CHAPTER SEARCH . . . .39
TIME SEARCH . . . . . . . . . . . . . . .39
MARKER SETUP SCREEN . . . . . .39
C
SPECIAL PLAYBACK FUNCTION . . .40
REPEAT . . . . . . . . . . . . . . . . . . . . .40
PROGRAM . . . . . . . . . . . . . . . . . . .40
RANDOM PLAYBACK . . . . . . . . .40
C
PLAYING A MP3 DISC . . . . . . . . . .41
MP3 PLAYBACK . . . . . . . . . . . . . .41
TRACK SELECTION . . . . . . . . . . .41
PROGRAM . . . . . . . . . . . . . . . . . . .41
RANDOM PLAYBACK . . . . . . . . .41
C
CHANGING THE SETTINGS . . . .42
SUBTITLE LANGUAGE . . . . . . . .42
AUDIO LANGUAGE . . . . . . . . . . .42
STEREO SOUND MODE . . . . . . . .42
CAMERA ANGLE . . . . . . . . . . . . .42
BLACK LEVEL SETTING . . . . . . .42
VIRTUAL SURROUND . . . . . . . . .42
C
THE ON-SCREEN INFORMATION . . .43
C
CHANGING THE DVD SETUP
ITEMS . . . . . . . . . . . . . . . . . . . . . . .44
LANGUAGE SETTING . . . . . . . . .44
DISPLAY SETTING . . . . . . . . . . . .45
AUDIO SETTINGS . . . . . . . . . . . .45
PARENTAL CONTROL . . . . . . . . .46
C
TROUBLESHOOTING GUIDE 47, 48, 49
C
MAINTENANCE . . . . . . . . . . . . . . .50
DISC HANDLING . . . . . . . . . . . . .50
C
SPECIFICATIONS . . . . . . . . . . . . .51
C
WARRANTY . . . . . . . . . . .Back Cover
C
ABOUT THE DISCS . . . . . . . . . . . .36
PLAYABLE DISCS . . . . . . . . . . . .36
DISC TYPES . . . . . . . . . . . . . . . . .36
C
PLAYING A DISC . . . . . . . . . . . . . .37
BASIC PLAYBACK . . . . . . . . . . . .37
GENERAL FEATURES . . . . . . . . .37
DISC MENU . . . . . . . . . . . . . . . . .37
TITLE MENU . . . . . . . . . . . . . . . . .37
RESUME . . . . . . . . . . . . . . . . . . . .38
PAUSE . . . . . . . . . . . . . . . . . . . . . .38
STEP BY STEP PLAYBACK . . . . .38
FAST FORWARD/REVERSE
SEARCH . . . . . . . . . . . . . . . . . . . .38
- 6 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 7
FEATURES
TV/VCR Mode
•
Hi-Fi system–
The Hi-Fi stereo recording system offers you excellent sound quality with a dynamic range of 80dB, frequency response from 20Hz to
20kHz, and 0.005% wow and flutter.
•
Rotary 4-head Record/Playback System–
Four heads ensure excellent picture quality and special effects playback.
•
Index Search–
Fast-forwards to start of next recording.
•
Slow Motion–
View recorded program at slower than normal speed.
•
Infrared remote control
•
Trilingual on screen tv/vcr setup display selectable in English or Spanish or French
•
Real time counter–
This shows the elapsed recording or playback time in hours, minutes, and seconds. The
“–” indication will appear when the tape is rewound further than the tape counter position “0:00:00”.
•
181 channel capability PLL frequency synthesizer tuner with direct station call–
(A converter may be necessary to view scrambled cable channels.)
•
Auto Clock Setting–
Allows you to set the clock function from a PBS broadcast station.
•
Closed caption system–
You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or text display added to the program.
•
Auto power on and off system–
Automatically turns on the TV/DVD/VCR when you insert the cassette, turns off after auto-rewind, and ejects when the beginning of the tape is reached.
•
Auto rewind when the end of a tape is reached–
This function doesn’t occur when using timer recording.
•
Smooth mode change–
TV/VCR mode, DVD mode automatically changes without control.
•
2 Step picture search operation–
You can view a video program at a high speed or super high speed in either a forward or reverse direction in LP and
SLP mode. For SP mode only high speed.
•
Three different playback tape speeds : SP/LP/SLP
•
Two different recording tape speeds : SP/SLP
•
Auto Head Cleaner–
Automatically cleans video heads as you insert or remove a cassette.
•
Zero Return–
The tape returns to counter of
0:00:00 by rewinding or fast forwarding.
•
Still–
“Freeze” the picture at any time, for close viewing of a particular scene.
•
Digital Auto Tracking (DTR)–
Automatically adjusts the tracking for each tape you play.
•
Rental play mode–
Improves playback picture quality from worn tapes, such as rental tapes.
•
Auto repeat–
Allows you to repeat the playing of a tape indefinitely without pressing the PLAY button.
•
Time search–
Let you set the TV/DVD/VCR to advance the tape by entering the desired playback time you want to skip.
•
OTR (One Touch Recording)–
Instant timed recording from 30 to 480 minutes is possible at the push of the REC/OTR button.
•
1 Year, 8 events (including Daily and Weekly
Timer Recording)–
The built-in timer allows you to record up to 8 programs at different times on different channels up to 1 year in advance. The Daily timer allows recordings to be made of daily broadcasts, and the Weekly timer allows recording to be made once a week up to the end of the tape.
•
Auto return–
After timer recording is finished, the
TV/DVD/VCR can return to the beginning of the recording.
•
Sleep timer–
Allows you to have the TV/DVD/VCR automatically turn on or off at a desired time.
Timer Program Extension–
Allow you to shift the time schedule for automatic timer recording.
•
V-CHIP–
Enables parents to prevent their children from watching inappropriate material on TV.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
- 7 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 8
DVD Mode
¡
Dolby Digital sound
This player can handle Dolby Digital surround sound having 5.1 channels when connected to a
Dolby Digital decoder
.
¡
Still/fast/slow/step playback
Various playback modes are available including still pictures, fast forward/reverse, slow motion and step frames.
¡
Random playback for audio CD and MP3
This player can shuffle the order of tracks to play them in random order.
¡
Program playback for audio CD and MP3
You can program the order of tracks to play them in any desired order.
¡
DVD menus in a desired language
You can display DVD menus in a desired language, if available on a DVD.
¡
Screen saver/Auto power-off functions
The screen saver program starts when there is no input from the player for five minutes in the stop mode. When the screen saver program is activated for 15 minutes, the power automatically turns off.
¡
Subtitles in a desired language
You can select a desired language for the display subtitles, if that language is available on a disc.
¡
Selecting a camera angle
You can select the desired camera angle, if a disc contains sequences recorded from different angles.
¡
Choices for audio language and sound mode
You can select the desired audio language and sound mode, if different languages and modes are available on a disc.
¡
Parental lock
You can set the control level to limit playback of discs which may not be suitable for children.
¡
Automatic detection of discs
This player automatically detects if the loaded disc is
DVD, audio CD or MP3 on disc.
¡
Playback MP3 disc
¡
On-screen display
Information about the current operation can be displayed on a TV screen, allowing you to confirm the currently active functions (such as program playback), on the TV screen using the remote control.
¡
Search
Chapter search / Title search / Track search / Time search
¡
Repeat
Chapter / Title / Track / Group / All / A-B
¡
Zoom
Magnified screen can be displayed.
¡
Marker
The part designated by user can be called back.
¡
Resume Play
User can resume to playback from the part at which the play was stopped.
¡
Virtual Surround
¡
Bit rate indication
¡
DRC (Dynamic range control)
You can control the range of sound volume.
NOTE:
•
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with a universal remote control.
If you decide to use a universal remote control with this TV/VCR/DVD, please be aware that the code number given may not operate this TV/VCR/DVD. In this case, please call the manufacturer of the universal remote control.
- 8 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 9
OPERATING CONTROLS AND FUNCTIONS
- TV/DVD/VCR FRONT PANEL - [Fig.1]
POWER VOLUME
DVD buttons
SKIP PLAY SKIP STOP OPEN/CLOSE
SEARCH
DVD
SELECT
TV/VCR
TV/VCR buttons
CHANNEL REC/OTR REW PLAY F.FWD
STOP
EJECT
HEADPHONE VIDEO L AUDIO R
1 2 3 4 3 5 6 7 8 9 10 11 12 13 14 4 15 16 17 18 19 20 21
- REMOTE CONTROL -
[Fig. 2]
1
22
23
24
25
26
(DVD)
3
(TV/VCR)
14
4
13
27
28
29
30
45
44
11
2
43
42
3
(DVD)
15
(TV/VCR)
5 (TV/VCR
41
40
39
38
/DVD/CD)
37
5.
STOP Button
Front panel
[P.37]
Press to stop the disc motion.
Remote Control
●
DVD mode
[P.37]
Press to stop the disc motion.
●
TV/VCR mode
[P.26]
Press to stop the tape motion.
6.
OPEN/CLOSE Button
[DVD P.37]
Press to insert discs into or remove them from the tray.
7.
Disc loading tray
8.
DVD Indicator
Lights on during DVD mode.
9.
SELECT Button
Press to change to TV/VCR mode, external input mode or DVD mode.
10.
TV/VCR Indicator
Lights on during TV/VCR mode.
11.
CHANNEL
K
/
L
Buttons
Press to select memorized channel.
12.
Recording Indicator
Flashes during recording. Lights up in the Standby mode for Timer Recording.
31
32
33
36
35
34
1.
POWER Button
[TV/VCR P.15 / DVD P.37]
Press to turn the power on and off.
2.
VOLUME
X
/
Y
Buttons
Press to control the volume level for the DVD and
TV.
3.
SKIP Buttons (for DVD)
[P.38]
Press once to skip chapters or tracks to a desired point.
Press and hold to change forward or reverse playback speed.
4.
PLAY Button
[TV/VCR P.26 / DVD P.37]
Starts playback of the disc or tape contents.
- 9 -
13.
REC/OTR (RECORD)Button
[TV/VCR P.30, 31]
Press for manual recording. Activates One Touch
Recording. (OTR is only during TV/VCR mode.)
14.
REW Button (for TV/VCR)
[TV/VCR P.26]
Press to rewind the tape, or to view the picture rapidly in reverse during playback mode. (Rewind
Search)
15.
FWD Button (for TV/VCR)
[TV/VCR P.26]
Press to rapidly advance the tape, or to view the picture rapidly in forward during playback mode.
(Forward Search)
16.
STOP/EJECT Button
[TV/VCR P.28]
Press to stop the tape motion. Press in the Stop mode to remove tape from the TV/VCR/DVD.
17.
Remote sensor window
EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 10
- TV/DVD/VCR REAR PANEL - [Fig.3]
46
18.
HEADPHONE Jack
To connect headphone (not supplied) for personal listening.
19.
VIDEO input Jack
Connect to the video output jack of a video camera or VCR.
20.
AUDIO L/R input Jacks
Connect to the audio output jacks of a video camera or VCR.
21.
Cassette compartment
22.
PICTURE Button
Press to adjust the picture.
23.
Number Buttons
TV Mode:
[P.15]
Press two digits to directly access the desired channel.
Remember to press a "0" before a single digit channel.
+100 Button–
Press to select cable channels which are equal or greater than number 100.
DVD Mode:
Press to enter the desired number.
+10 Button–
Press to enter the desired numbers which are equal or greater than number 10.
24.
PAUSE Button
[TV/VCR P.26 / DVD P.38]
Pauses the current disc or tape operation.
25.
SPEED Button
[TV/VCR P.30]
Press to choose the desired recording speed:
SP/SLP.
26.
C.RESET Button
[TV/VCR P.28]
Press to reset counter to 0:00:00.
Press to cancel a setting of timer program. (See page 33.)
27.
DISPLAY Button
TV/VCR Mode:
Display the counter or the current channel number and current time on the TV screen.
DVD Mode:
[P.43]
Displays the current status on the TV screen for checking purposes.
47 48 49
28.
SETUP Button
[TV/VCR P.15] [DVD P.44-46]
Press to enter or exit the TV menu or DVD setup mode.
29.
TITLE Button
[DVD P.37]
Displays the title menu.
30.
CLEAR Button
Resets a setting.
31.
MODE Button
[DVD P.41]
Activates program playback or random playback mode.
32.
SEARCH MODE Button
[DVD P.39]
Press to locate a desired point.
33.
AUDIO Button
[DVD P.42]
Press to select a desired audio language or sound mode.
34.
SUBTITLE Button
[DVD P.42]
Press to select a desired subtitle language.
35.
REPEAT Button
[DVD P.40]
Repeats playback of the current disc, title, chapter or track.
36.
ANGLE Button (DVD mode)
[DVD P.42]
Press to change the camera angle to see the sequence being played back from a different angle.
37.
A-B REPEAT Button
[DVD P.40]
Repeats playback of a selected section.
38.
RETURN Button
Returns to the previous operation in the DVD setup mode.
39.
ENTER Button
Press to accept a setting.
40.
Arrow Buttons
TV/VCR Mode:
Press to select a setting mode from the menu on the TV screen.
Press to select or adjust from a particular menu.
DVD Mode:
Use when making settings while watching the display on a TV screen.
41.
DISC MENU Button
[DVD P.37]
Displays the menus in the DVD.
42.
ZOOM Button
[DVD P.38]
Enlarges part of a DVD-reproduced image.
- 10 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 11
43.
MUTE Button
Mutes the sound. Press it again to resume sound.
44.
SLEEP Button
[TV/VCR P.34]
Sets the Sleep Timer.
45.
SELECT Button
Press to switch TV/VCR and DVD mode. You can see the mode (TV/VCR or DVD) on the front panel indicator.
46.
ANT. in Jack
Connect to an antenna, cable system, or satellite system.
47.
Power cord
Connect to a standard AC outlet (120V/60Hz).
NOTE:
Remove the power cord from the hook to avoid breaking a wire before you connect to a standard AC outlet.
48.
COAXIAL digital audio out Jack
Connect to the digital input of an external amplifier or decoder for DVD audio only.
49.
AUDIO L/R output Jack
Connect to the analog audio input of an external amplifier or decoder.
PREPARATION FOR USE
Satellite Box or
Cable Box (Not supplied)
OUT
IN
ANTENNA/CABLE CONNECTION
From Cable System or
Satellite Dish
VHF/UHF Antenna
(Not supplied)
VHF Antenna (Not supplied)
From Cable
System
75-ohm
Coaxial
Cable
(Not supplied)
UHF Antenna
(Not supplied) or
VHF/UHF
Combiner
(Not supplied)
ANT.
75-ohm Coaxial
Cable (Not supplied) or or
Flat twin-lead cable
[Fig. 4]
VHF/UHF SEPARATE ANTENNAS
In some areas it will be necessary to use an outdoor antenna.
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
Use this connection if your cable system connects directly to your TV/DVD/VCR without a converter box.
By using this connection you can:
1) Use the TV/DVD/VCR remote to select channels.
2) Program one or more unscrambled channels for
Automatic Timer Recording.
NOTE: This TV/VCR/DVD will ONLY record and view the same channel.
- 11 -
CABLE WITH CONVERTER/
DESCRAMBLER BOX OR SATELLITE
BOX
If your cable service supplies you with a converter box or if you use a satellite system, you can use the basic connection shown in the illustration.
By using this connection you can also record scrambled channels. However, channel selection must be made with the converter box or satellite box. This means that channels cannot be changed using the
TV/DVD/VCR Remote Control. Unattended timer recording is limited to one channel at a time.
Antenna/Cable Connections
Continued on the Next Page.
EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 12
TO RECORD A SCRAMBLED/UNSCRAM-
BLED CHANNEL
1. Set the TV/DVD/VCR channel selector to the output channel of the Cable Converter Box or Satellite
Box. (Ex. CH3)
2.Select the channel to record from your Cable
Converter Box or Satellite Box.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the
NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow.
2)Insert 2 “AA” penlight batteries into the battery compartment in the direction indicated by the polarity (+/-) markings.
3)Replace the cover.
CONNECTING TO EXTERNAL
INPUT JACKS
When you watch a program recorded on an another source (VCR or video camera), use the audio/video input jacks on the front of the TV/DVD/VCR.
Connect the audio/video output jacks of another source to the AUDIO L/R and VIDEO jacks of this
TV/DVD/VCR.
Then press the CHANNEL buttons K/L until "AUX" appears on the screen.
NOTE:
•
When you connect a monaural VCR (another source) to this TV/DVD/VCR, connect the Audio output jack of the monaural VCR (another source) to the AUDIO L jack of this TV/DVD/VCR. The audio will output in both L and R channel equally.
To the audio output jacks
[Another source]
EXTERNAL INPUT MODE
When using an external input signal (another VCR or video camera), connect the player’s audio/video output cables to the AUDIO L/R IN/
VIDEO IN jacks of your
AUX
TV/DVD/VCR. Then press the
CHANNEL button K or L until
“AUX” appears on the screen.
etc.
To the video output jack
Audio/Video coaxial cable
(not supplied)
HEADPHONE VIDEO L AUDIO R
[Front of the
TV/DVD/VCR]
[Fig. 5]
- 12 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 13
CONNECTING TO A STEREO SYSTEM
Stereo system
To ANALOG AUDIO INPUT jacks
To Right (red) and Left (white)
AUDIO OUT jacks
[Fig. 6]
NOTES:
•
Be sure to turn off the power to all components in the system before connecting another component.
•
Refer to the Owner's Manuals for your stereo system and any other components to be connected to the
TV/DVD/VCR.
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH DIGI-
TAL INPUT JACKS SUCH AS MD DECK OR DAT DECK (for DVD)
Use an audio coaxial digital cable available at retail for the audio connections.
Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
Amplifier equipped with digital input jacks, MD deck,
DAT deck, etc.
To COAXIAL DIGITAL
AUDIO INPUT jack
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
(only DVD AUDIO OUT)
[Fig. 7]
NOTES:
•
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital sound by an MD or DAT deck.
•
Be sure to turn off the power to all components in the system before connecting another component.
•
Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VCR.
•
Set Dolby Digital to OFF for audio output in the setup mode. Playing a TV/DVD/VCR using incorrect settings may generate noise distortion, and may also damage the speakers.
- 13 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 14
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)
If using this TV/DVD/VCR to play a DVD disc in a 5.1 channel Dolby Digital surround format, the
TV/DVD/VCR outputs a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the player up to a Dolby Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound as enjoyed in movie theaters.
Use audio coaxial digital cables available at retail for the audio connections.
Front speaker
(left)
Center speaker
Front speaker
(right)
Surround speaker
(left)
Dolby Digital decoder
Surround speaker
(right)
To COAXIAL DIGITAL
AUDIO INPUT jack
Subwoofer
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
[Fig. 8]
NOTES:
•
Be sure to turn off the power to all components in the system before connecting another component.
•
Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VCR.
•
If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.
(See page 45 to set DOLBY DIGITAL to ON.)
•
Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a TV/DVD/VCR using incorrect settings may generate noise distortion, and may also damage the speakers.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
- 14 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 15
TV/VCR SECTION
SET UP FOR USE
You can program the tuner to scan all the channels you receive in your area.
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the TV/DVD/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3).
Then select the channel to be viewed on the Cable Box or Satellite Box.
CHANNEL SET UP FOR THE
FIRST TIME
DELETING (OR ADDING)
CHANNEL
TV/VCR
TV/VCR
1
Plug in the TV/DVD/VCR power cord
The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.)
Plug the TV/DVD/VCR power cord into a standard AC outlet.
NOTE:
•
If some digits appear in the corner of the screen, press the POWER button without unplugging the power cord.
1
Select “CHANNEL SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “CHANNEL SET UP”.
Then, press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
B
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Turn on the TV/DVD/VCR
Press the POWER button to turn on the TV/DVD/VCR.
3
Select “ENGLISH” or “ESPAÑOL” or
2
Select “ADD/DELETE CH”
Press the Arrow button K or L to point to “ADD/DELETE CH”.
– CHANNEL SET UP –
B ADD / DELETE CH (TV)
AUTO PRESET
“FRANÇAIS”
Select “ENGLISH” or
“ESPAÑOL”=Spanish or
“FRANÇAIS” =French using the
ENTER button. “[ ]” indicate the selected language.
– SET UP –
B LANGUAGE
[ENGLISH] ESP
AUTO PRESET
FRA
Press the ENTER button.
3
Enter the desired channel number
4
Begin auto preset
Press the Arrow button K or L to point to “AUTO PRESET”.
– SET UP –
LANGUAGE
[ENGLISH] ESP FRA
Press the Arrow button K or L until your desired channel number appears.
(You can also use the number buttons or the CHANNEL buttons K/L to enter it) (Example: CH8)
ADD / DELETE
08
B
AUTO PRESET
Then press the ENTER button.
The tuner scans and memorizes all active channels in your area.
NOTES:
•
The TV/DVD/VCR distinguishes between standard
TV channels and cable channels.
•
If you want to play or record a video tape
BEFORE presetting the tuner, you must press the
SETUP button on the remote control. To preset the tuner again, see “CHANNEL SET UP AGAIN” on page 16.
•
The TV/DVD/VCR may memorize TV channels as
CATV channels if reception conditions is poor. If this happens, try AUTO MEMO action again when reception conditions are better.
4
Delete (or add) it from (into) memory
Press the ENTER button. The channel number changes to light red. The channel is deleted from memory.
Added channel: Light blue.
Deleted channel: Light red.
•
To delete another channel, repeat steps [3] and [4].
•
If you press the ENTER button again, the channel is memorized again.
•
Press the RETURN button to return to TV/VCR
SETUP MENU.
5
Exit the channel setup mode
5
After scanning
Press the SETUP button on the remote control to
The tuner stops on the lowest memorized channel.
If you want to recall the selected channels, you can select the desired channel directly with the remote control number buttons or the CHANNEL button K or L.
- 15 returns to TV mode.
NOTE: To confirm that channel(s) has been deleted or added, press the CHANNEL button K or L.
EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 16
CHANNEL SET UP AGAIN
Make sure ...
•
Press the POWER button to turn on the
TV/DVD/VCR.
TV/VCR
1
Select “CHANNEL SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “CHANNEL SET UP”.
Then, press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
B
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Begin auto preset
Press the Arrow button K or L to point to “AUTO PRESET”.
Then, press the ENTER button.
The tuner scans and memorizes all the active channels in your area.
– CHANNEL SET UP –
ADD / DELETE CH (TV)
B
AUTO PRESET
3
After scanning
The tuner stops on the lowest memorized channel.
SELECTING THE LANGUAGE
TV/VCR
Make sure ...
•
Press the POWER button to turn on the
TV/DVD/VCR.
NOTE: This function effects only the language on the screen menu and not the audio source.
1
Select “LANGUAGE”
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “LANGUAGE”.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select “ENGLISH” or “ESPAÑOL” or
“FRANÇAIS”
Select “ENGLISH” or “ESPAÑOL”= Spanish or
“FRANÇAIS”= French using the ENTER button.
3
Exit the Language mode
Press the SETUP button on the remote control to return to TV mode.
NOTE: If Spanish or French is selected accidentally,
1) Press the SETUP button on the remote control.
2) Press the Arrow button K or L to point to “IDIOMA
[ESPAÑOL]” or “LANGAGE” [FRANÇAIS].
3) Press the ENTER button to select your desired language.
4) Press the SETUP button to exit.
DAYLIGHT-SAVING TIME
TV/VCR
Select this feature and the TV/DVD/VCR’s clock automatically will advance one hour in April, then reverse one hour in October.
When Daylight-Saving Time is ON, the clock will change automatically as follows:
•
First Sunday of April :
At 2 AM the clock immediately changes to 3 AM. Any timer programming you have set to occur between 2 AM and 3 AM will not record.
•
Last Sunday of October :
At 2 AM the clock immediately changes to 1 AM.
Make sure ...
•
Press the POWER button to turn on the
TV/DVD/VCR.
1
Select “SETTING CLOCK”
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “SETTING CLOCK.”
Then, press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
B
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Set “D.S.T.” (Daylight-Saving
– SETTING CLOCK –
Time) to [ON]
Press the Arrow button K or L to point to “D.S.T.”
Then, press the ENTER button until
[ON] appears.
AUTO CLOCK [ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
[02]
B
D.S.T.
[ON]
3
Exit the Daylight-Saving Time mode
Press the SETUP button on the remote control to return to TV mode.
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps [1] to [2], select [OFF] using the
ENTER button.
- 16 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 17
CLOCK SET UP
(AUTO / MANUAL)
TV/VCR
The TV/DVD/VCR clock must be set correctly before
VCR timer recording is possible. It is suggested that the clock be set manually when first setting up the
TV/DVD/VCR. Then, setup auto clock correction which will periodically correct the setting if necessary.
NOTE: If you cannot receive a station with time signals, auto clock setting cannot be performed. Use manual setting only.
MANUAL CLOCK SETTING
Make sure ...
•
TV/DVD/VCR power is turned on.
In the example below, the clock is to be set to:
DATE May 6th, 2003
SETTING TIME 5:40PM
1
Select “SETTING CLOCK”
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “SETTING CLOCK”.
Then, press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
B
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select “MANUAL CLOCK
– SETTING CLOCK –
SET”
Press the Arrow button K or L to point to “MANUAL CLOCK SET”.
Then, press the ENTER button.
AUTO CLOCK [ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH [02]
B
MANUAL CLOCK SET
D.S.T.
[OFF]
6
Select the hour
Press the Arrow button K or L until your desired hour appears.
(Example: 5, PM)
Then, press the Arrow button B.
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 6 TUE 2 0 0 3
HOUR MINUTE
0 5 : – – PM
7
Select the minute
Press the Arrow button K or L until the desired minute appears.
(Example: 40)
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 6 TUE 2 0 0 3
HOUR MINUTE
0 5 : 4 0 PM
8
Start the clock
5:40 PM
Press the SETUP button on the remote control.
Although seconds are not displayed, they begin counting from 00 when you press the SETUP button on the remote control. Use this feature to synchronize the clock with the correct time.
NOTE:
When unplugging the AC cord or if there is a power failure for more than 3 seconds, you may have to reset the clock.
TO CHANGE CLOCK SETTING
If you want to change the clock,
1)Follow steps [1] and [2].
2)Select where you want to change using the Arrow button B or s.
3)Enter correct numbers using the Arrow button K or
L
.
4)Press the SETUP button on the remote control to start the clock.
3
Select the month
Press the Arrow button K or L until your desired month appears.
(Example: May → 05)
Then, press the Arrow button B.
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / – – – – – – – – –
HOUR MINUTE
– – : – – – –
PLEASE NOTE:
If there is no local PBS station in your area or on your cable system, select “AUTO CLOCK” and press the ENTER button to turn [OFF] this function.
Then you can manually adjust the clock.
4
Select the day
Press the Arrow button K or L until your desired day appears.
(Example: 6th → 06)
Then, press the Arrow button B.
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 6 – – – – – – –
HOUR MINUTE
– – : – – – –
5
Select the year
Press the Arrow button K or L until your desired year appears.
(Example: 2003)
Then, press the Arrow button B.
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 6 TUE 2 0 0 3
HOUR MINUTE
– – : – – – –
- 17 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 18
AUTOMATIC CLOCK SETTING
Make sure ...
•
The TV/DVD/VCR is turned on.
•
Confirm the TV/DVD/VCR is receiving a RF
(Radio Frequency) signal from either an antenna or cable system connection using the ANT IN jack on the rear of the TV/DVD/VCR.
NOTE:
•
If a cable converter box is being used, make sure it is powered on.
•
You must use the TV/DVD/VCR remote control to perform the clock setting procedure.
Press the Arrow button K or L to select “SETTING CLOCK”.
Press the ENTER button to enter
“SETTING CLOCK” menu.
Press the Arrow button L to select
“AUTO CLOCK CH”.
Press the ENTER button, then press the Arrow button B or s until you locate Auto Clock Set station number. See item 3 above.
Press the SETUP button to exit the screen.
- TV/VCR SETUP -
TIMER PROGRAMMING
B
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– SETTING CLOCK –
AUTO CLOCK [ON]
AUTO CLOCK CH SEARCH
B
AUTO CLOCK CH [ 45]
MANUAL CLOCK SET
D.S.T.
[OFF]
1
Select “SETTING CLOCK”
Press the SETUP button on the remote control.
Press the Arrow button K or L to select “SETTING CLOCK”.
Press the ENTER button to enter
“SETTING CLOCK” menu.
B
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
5
Turn off the TV/DVD/VCR
Once the TV/DVD/VCR is turned off , it will periodically check and set the correct date and time.
2
Set “AUTO CLOCK” to [ON]
Press the ENTER button until
AUTO CLOCK [ON] appears.
– SETTING CLOCK –
B
AUTO CLOCK [ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[02]
[OFF]
3
Begin “AUTO CLOCK CH SEARCH”
Press the Arrow button L to select “AUTO CLOCK
CH SEARCH”.
Press the ENTER button.
•
The TV/DVD/VCR is now searching for the station which contain the auto clock set signal.
The search for a signal may take up to 20 seconds per channel.
•
“_ _” appears at the lower left of the screen when the search has ended.
•
Auto Clock station- write down the number(s) that appear on the
– SETTING CLOCK –
AUTO CLOCK [ON]
B
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
[02]
D.S.T.
[OFF]
– AUTO CLOCK CH SEARCH –
08 10 13 screen. These are the auto clock station(s) in your area. See item
_ _
4 below.
•
If no number(s) appear on the TV screen, there are no stations in your area which contain the Auto
Clock signal. Auto Clock Setting is not possible.
Please use Manual Clock Setting on page 17.
Press the SETUP button to exit the screen.
NOTE: During Auto Clock CH Search, the picture may be distorted. This is normal.
4
Enter the channel number that contains the
Automatic Clock Setting Signal
Press the SETUP button on the remote control.
- 18 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 19
TV OPERATION
WATCHING A TV PROGRAM
1
Turn on the TV/DVD/VCR
Press the POWER button to turn on the
TV/DVD/VCR.
TV/VCR
PICTURE CONTROL
The TV/DVD/VCR’s picture controls – BRIGHT,
CONTRAST, COLOR, TINT and SHARPNESS – are preset to factory specifications. Although they are usually the best, you may need to make some further adjustments for a natural looking image.
NOTES:
•
Procedures must be followed within 5 seconds or the Picture Control mode will be cancelled.
•
When setting the Picture Control, the Game mode will be cancelled.
Make sure ...
•
TV/DVD/VCR power must be turned on.
TV/VCR
2
Select the channel number
Press the CHANNEL button K or L to select your desired channel number or press the number on the remote control.
Note for using the Number button on the remote control:
¡ When selecting cable channels which are higher than 99, press +100 first, then, press the last two digits. (Example: to select channel 125, first press
“+100” then press “2” and “5”).
¡ You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).
Remember: If the TV/DVD/VCR is connected to a cable box or satellite box, the TV/DVD/VCR must be on CH3 or CH4, then the channel to be viewed must be selected on the cable box or satellite box.
3
Adjust sound
Press the VOLUME button X
Y to adjust the volume.
VOLUME 20
C C C C C
C C C C C C C
1
Select “PICTURE CONTROL”
Press the PICTURE button on the remote control.
2
Select item you want to adjust
Press the Arrow button K or L until desired control is displayed.
BRIGHT
CONTRAST
COLOR
TINT
SHARPNESS
BRIGHT
+
NOTES:
•
If you press the CHANNEL button o or p in the
DVD mode, you can change the TV channels.
Even if you turn off the TV/DVD/VCR in the
DVD mode, when you turn it on again, it will go into the TV/VCR mode.
3
Adjust the picture control
Press the Arrow button B or s to adjust to your desired level.
DEGAUSSING
TV/VCR
Magnetism from nearby appliances and speakers might affect the color of the TV picture.
If this happens, move this TV/VCR/DVD away from the appliance. If the color is still not correct, turn off using the POWER button, then turn it on again 30 minutes or so later (27” model), or unplug the power cord, then plug it in again 30 minutes or so later (19” model).
BRIGHT
Arrow button s Arrow button B to decrease brightness
CONTRAST
to decrease contrast to increase brightness to increase contrast
COLOR
to pale to brilliant
TINT
to purple
SHARPNESS
to soft to green to clear
•
If there is a power failure of any kind, the
TV/VCR/DVD will retain its memory for this feature.
- 19 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 20
CLOSED CAPTION SYSTEM
TV/VCR
You can view specially labeled (cc) TV programs, movies, news, pre-recorded tapes with either a dialogue caption or text display.
CAPTION mode:
By choosing the caption mode, you can watch dramas, movies and news while captioning the dialogues and the contents of news.
TEXT mode:
By choosing the text mode, you can watch half screen text information if you want.
1-2:
You may get these captions or text information by selecting either “1” or “2”. Caption “2” is used, usually for a second language if available.
1
Select “CAPTION”
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “CAPTION”.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select your desired caption menu
Press the ENTER button until your desired caption menu appears.
([CAPTION1], [CAPTION2],
[TEXT1] or [TEXT2])
B
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [CAPTION1]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
NOTE:
Not all programs are broadcast with closed captions.
Your television is designed to provide error free closed captions from high quality antenna, cable and
VCR signals. Conversely, poor quality signals are likely to result in caption errors or no captions at all.
Common signal conditions which may cause captions errors are listed below:
•
Automobile ignition noise
•
Electric motor brush noise
•
Weak snowy reception on TV screen
•
Multiplex signal reception displaying picture ghosts or airplane flutter.
•
Playback of poorly recorded or worn VCR tapes.
NOTE:
If the TV/DVD/VCR displays a black box on the TV screen, this means that the TV/DVD/VCR is set to the TEXT mode. To clear screen, select [CAPTION1], [CAP-
TION2] or [OFF].
Make sure ...
•
TV/DVD/VCR power must be turned on.
3
Exit the caption setting mode
Press the SETUP button on the remote control to return to TV mode.
TO CANCEL THE CLOSED CAPTION
SYSTEM
Repeat steps [1] and [2], select [OFF] using the
ENTER button. Press the SETUP button on the remote control to return to TV mode.
WHEN THE CLOSED CAPTION MODE
IS ON
The On-Screen Display will disappear after 5 seconds.
•
It will also disappear when the MUTE button is pressed, and when the PAUSE button is pressed while recording.
•
If there is a power failure of any kind, the
TV/DVD/VCR will retain its memory for this feature.
- 20 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 21
V-CHIP SET UP
V-CHIP SET UP
Make sure ...
•
TV/DVD/VCR is turned on.
TV/VCR
1
Select “V-CHIP SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to select “V-CHIP SET UP”.
Then, press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Enter Access code
ACCESS CODE
Use the number buttons on the remote
_ _ _ _ control to enter the access code.
•
For the first time set-up or in the event the TV/DVD/VCR has lost power, enter the default code of the numbers:
0000.
3
Select “TV RATING”
Press the Arrow button K or L to select “TV RATING”.
Then, press the ENTER button.
– V-CHIP SET UP –
B
TV RATING
MPAA RATING
CHANGE CODE
V-CHIP SET UP SUB RATINGS
When you select the ratings of TV-Y7,TV-PG,TV-14 or TV-MA you will have the option of selecting sub rating categories.
1
Select “V-CHIP SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to select “V-CHIP SET UP”. Then, press the ENTER button.
B
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Enter Access code
Use the number buttons on the remote control to enter the access code. (Default code is 0000.)
ACCESS CODE
_ _ _ _
3
Select “TV RATING”
Press the Arrow button K or L to select “TV RATING”.
Then, press the ENTER button.
– V-CHIP SET UP –
B
TV RATING
MPAA RATING
CHANGE CODE
4
Blocking TV programs
Press the Arrow button K or L to select “TV rating” that you wish to block.
B
TV–Y
TV–Y7 (
TV–G
TV–PG (
TV–14 (
TV–MA (
)
)
)
)
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
Press the ENTER button to turn it
[BLOCK].
•
When you select the rating category and turn it
[BLOCK], the higher rating will turn [BLOCK] automatically. Also, the lower rating will turn
[VIEW] automatically.
•
When you turn “TV-Y” to [VIEW], then all ratings will turn to [VIEW] automatically.
Selection
TV-Y
Rating Category Explanations
Appropriate for all children
TV-Y7 Appropriate for children seven and older
TV-G General Audience
TV-PG Parental Guidance suggested.
TV-14 Unsuitable for children under 14
TV-MA Mature audience only
4
Selecting Sub-Ratings”
Press the Arrow button L to select the sub-rating you wish to block. Then, press the ENTER button twice.
•
When you select [TV-Y7]:
Press the Arrow button L or K to select “FV” (Fantasy Violence).
TV–Y7 [BLOCK]
Then, press the ENTER button to select [BLOCK] or [VIEW].
•
When you select [TV-PG], [TV-
14] or [TV-MA]:
B
FV [BLOCK]
Press the Arrow button L or K to select “D”(Suggestive Dialog),
“L”(Coarse Language),
“S”(Sexual Situation), or
TV–PG
B
D
L
S
V
“V”(Violence). Then, press the
ENTER button to select [BLOCK] or [VIEW].
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
Note: When you select [TV-MA], “D” does not appear on the TV screen.
•
The sub-ratings which set to
[BLOCK] appears next to the rating category in the TV rating menu.
B TV–Y
TV–Y7 (
TV–G
)
TV–PG (DLSV )
TV–14 (DLSV )
TV–MA ( LSV )
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
5
Exit the V-Chip setting mode
Press the SETUP button on the remote control to enter the setting and exit the screen.
5
Exit the V-Chip setting mode
Press the SETUP button on the remote control to exit the screen.
- 21 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 22
CHANGING V-CHIP BLOCKED PRO-
GRAMMING
Note: To change the rating, the TV must be turned to a station that is not protected. If the (PROTECTED) appears on the screen, please change the channel to a station that is not protected.
1)Follow steps [1] and [2].
2)Press the Arrow button K or L to select "TV RAT-
ING". Then, press the ENTER button. Select a TV rating to be unblocked by pressing the Arrow button K or L.
Then press the ENTER button to unblock the rating.
3)Press the SETUP button on the remote control to exit the screen.
5
Exit the V-Chip setting mode
Press the SETUP button on the remote control to exit the screen.
CHANGE ACCESS CODE
To change access code, follow the steps.
1
Select “V-CHIP SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to select “V-CHIP
SET UP”.
Then, press the ENTER button.
MPAA RATING SET UP
1
Select “V-CHIP SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to select “V-CHIP SET UP”. Then, press the ENTER button.
2
Enter Access code
Use the number buttons on the remote control to enter the access code.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
ACCESS CODE
_ _ _ _
2
Enter Access code
Use the number buttons on the remote control to enter the access code.
The default code is 0000.
ACCESS CODE
_ _ _ _
3
Select “CHANGE CODE”
Press the Arrow button K or L to select "CHANGE CODE". Then, press the ENTER button.
– V-CHIP SET UP –
TV RATING
MPAA RATING
B
CHANGE CODE
3
Select “MPAA RATING”
Press the Arrow button K or L to point to “MPAA RATING”.
Then, press the ENTER button.
– V-CHIP SET UP –
TV RATING
B
MPAA RATING
CHANGE CODE
4
Select your desired item
Press the Arrow button K or L to point to your desired item.
Then, press the ENTER button to select [BLOCK] or [VIEW].
G
PG
PG–13
B
R
NC–17
X
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
Selection
G
PG
Rating Category Explanations
General Audience
Parental Guidance suggested.
PG-13 Unsuitable for children under 13
R Restricted; under 17 requires accompanying parent or adult guardian
NC-17 No one under 17 admitted
X Mature audience only
•
When you select the rating category and turn it
[BLOCK], the higher rating will turn [BLOCK] automatically. Also, the lower rating will turn
[VIEW] automatically.
•
When you turn “G” to [VIEW], then all ratings will turn to [VIEW] automatically.
- 22 -
4
Enter New code
Use the number buttons to enter your desired access code in the
NEW CODE space. Then enter the same code in the CONFIRM
CODE space. V-CHIP SET UP
NEW CODE
X X X X
CONFIRM CODE
_ _ _ _ screen appear on the screen.
•
If you enter wrong code, repeat step 4, making sure you enter the same new code exactly in the confirm code space.
5
Exit the V-Chip setting mode
Press the SETUP button on the remote control to exit the screen.
Note: If you unplug the power code or power failure occurs, the changed access code will be lost and will return to default (0000). Change your access code again as necessary.
EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 23
MTS(Multi-Channel Television sound)SYSTEM
You can record or listen to a program in MTS stereo.
When you play a VHS tape, or receive a broadcast on the
TV/DVD/VCR tuner channel you are watching, the status shown below will appear when you press the DISPLAY button on the remote control.
4]
CHECKING THE SELECTED MTS MODE
PLAY B
HIFI
12:00AM
CH 123
STEREO/SAP
SP COUNT 0:00:00
3]
2]
1]
SAP
Second Audio Program, which means your program, can also be received in a second language or sometimes a radio station.
HIFI
High Fidelity which produces better sound than standard stereo TV/DVD/VCRs.
TV/VCR
1] When a program is broadcast in stereo, STEREO appears on the TV screen.
2] When a program is broadcast in second audio,
SAP appears on the TV screen.
3] When a program broadcast both in stereo and second audio, STEREO and SAP appear on the TV screen.
NOTE: Although a program may be broadcast in both stereo and second audio, you cannot record in both stereo and second audio at the same time.
4] While the TV/DVD/VCR is set in HIFI stereo mode and playback mode. HIFI appears on the
TV screen. While the TV/DVD/VCR is set in monaural(MONO) mode, HIFI disappears from the TV screen.
NOTE: If you play non-HIFI tapes while the
TV/DVD/VCR is set in HIFI, HIFI will disappear from the TV screen and the
TV/DVD/VCR will play automatically in monaural.
MTS RECORDING/MONITOR MODE
Type of broadcast Display on STEREO/SAP
Regular
the TV screen SELECTION
-None-Invalid-
(monaural audio)
Stereo broadcast
Bilingual broadcast
STEREO
SAP
-Invalid-
STEREO*
TV/VCR
Hi-Fi audio track(2-channel) Normal audio
L-channel
Mono
R-channel
Mono
track
Mono
Stereo & Bilingual STEREO broadcast SAP
SAP*
STEREO*
SAP*
L
Main audio program
Sub audio program
L sub audio program
R
Main audio program
Sub audio program
R sub audio program
L+R
Main audio program
Sub audio program
L+R sub audio program
*
You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.
- 23 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 24
Make sure ...
SELECTING THE MTS SYSTEM
•
TV/DVD/VCR power must be turned on.
TO SELECT HIFI MODE
1
Select “USER’S SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “USER’S SET UP”. Then, press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select“VCR AUDIO”
Press the Arrow button K or L to point to“VCR AUDIO”.
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
B
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
TV/VCR
TO SELECT MONO MODE
You can change the selection to “MONO” if you want to listen to HIFI tapes in normal audio playback.
1) Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “USER’S
SET UP”.Then, press the ENTER button.
2) Press the Arrow button K or L to point to
“VCR AUDIO”.
3) Press the ENTER button until [MONO] appears.
4) Press the SETUP button on the remote control to return to TV mode.
3
Select [HIFI]
Press the ENTER button until
[HIFI] appears.
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
B
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
TO SELECT STEREO, SAP, OR MONO
1
Select “USER’S SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “USER’S SET UP”.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
4
To return to TV mode
Press the SETUP button on the remote control to return to TV mode.
2
Select “TV AUDIO”
Press the Arrow button K or L to point to“TV AUDIO”.
– USER’S SET UP –
B
RENTAL
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
NOTES:
•
Normally, “HIFI” should be selected for playback with HIFI sound.
•
When you play non-HIFI tapes, the TV/DVD/VCR will play automatically in the monaural mode.
•
The TV/DVD/VCR records automatically MTS broadcasts in HIFI stereo sound unless you select
SAP mode recording before you begin recording.
3
Select [STEREO], [SAP], or [MONO]
Press the ENTER button until [STEREO], [SAP], or
[MONO] appears.
- 24 -
4
To return to TV mode
Press the SETUP button on the remote control to return to TV mode.
NOTES:
•
You must select the recording mode,either TV
AUDIO [STEREO] or [SAP] when you record a broadcast.
Refer to “MTS RECORDING/MONITOR
MODE”.
•
If you select second audio when second audio is not available, the TV/DVD/VCR will record normal audio.
•
The TV/DVD/VCR records automatically MTS broadcasts in HIFI stereo sound unless you select
SAP mode recording before you begin recording.
EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 25
VIDEO CASSETTE
This TV/DVD/VCR will operate with any cassette that has the mark. For best results, we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.
PRECAUTIONS
•
Avoid moisture. Moisture condensation may occur on the tape if it is moved from a cold place to a warm place or visa versa. Before using a tape with these conditions, to avoid damage of the tape and your TV/DVD/VCR, wait until the tape has warmed to room temperature and the moisture has evaporated.
•
Avoid extreme heat, high humidity and magnetic fields.
•
Do not tamper with the cassette mechanism.
•
Do not touch the tape with your fingers.
TWO DIFFERENT TAPE SPEEDS
Before recording, select the tape speed from : SP
mode (Standard Play) or SLP mode (Super Long
Play).
The table below shows the maximum recording/playback time using T60, T120 or T160 tapes in each mode.
Tape Speed Recording/Playback Time
Type of tape
T60 T120 T160
SP mode
SLP mode
1 hour
3 hours
2 hours
6 hours
2-2/3 hours
8 hours
Note: You can play back a tape recorded in LP mode
(Long Play).
INSERTING A CASSETTE
Insert the cassette in the direction as shown. Push in gently, but continuously, on the center-back of the cassette until it is drawn into the TV/DVD/VCR. The
TV/DVD/VCR will automatically turn on.
Window
CORRECT WRONG
REMOVING A CASSETTE
1)In the Stop mode, press the EJECT button on the remote control or press the STOP/EJECT button on the TV/DVD/VCR. The cassette will eject.
2)Pull the cassette out of the cassette compartment.
3)Store the cassette in its case as shown.
ERASE PREVENTION
You can prevent accidental erasing of recording by breaking off the tab on the back edge of the cassette.
Tab
If you decide to record on the tape again, cover the hole with plastic tape.
- 25 -
Transparent Tape
NOTE:
• In DVD mode, Whether the cassette is with tab or without tab you insert, it doesn’t start playing until you press the PLAY button.
In TV/VCR mode, if th cassette without tab is inserted, playback will automatically start.
EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 26
PLAYBACK
NORMAL PLAYBACK SLOW MOTION
Make sure ...
•
TV/DVD/VCR power must be turned on.
TV/VCR
1
Insert a prerecorded tape
If the erase-protection tab has been removed, the
TV/DVD/VCR will start playback automatically.
TV/VCR
During pause, press the FWD button to reduce the playback speed. The TV/DVD/VCR mutes the sound during slow motion. Press the PLAY button to return to normal playback.
NOTE: If it is left in the Slow mode for more than five minutes, the TV/DVD/VCR will automatically go into the Stop mode.
2
To begin playback
Press the PLAY button.
3
To stop playback
Press the STOP button when playback is completed.
PLAY B
STOP
PICTURE SEARCH
TV/VCR
This feature is very useful in finding or skipping over a particular scene on a tape. In this mode, the sound will be muted.
1)You may view a video tape at a high speed in either a forward or reverse direction by pressing the F.FWD or REW button during playback. (in the
SP / LP / SLP modes)
NOTES:
•
If you press the PLAY button (of the TV/VCR side) in the DVD mode, you can start the VCR playback.
•
If you press the SELECT button in the VCR playback, it will stop and the mode will change to the
DVD mode. In addition, the same function operates with the DVD side PLAY button or the
OPEN/CLOSE button.
NOTE:
•
If you press the F.FWD or REW button on the front panel in the DVD mode, the VCR forward or reverse will start. Please press the STOP /
EJECT button once to stop it, twice to eject it.
2)Press it again and the TV/DVD/VCR will now search in super high speed. (in the LP / SLP modes only)
NOTE:
•
Tapes recorded in the SP or LP mode will display a noise bar on the TV screen and the picture may revert to Black and White. This is normal.
3)Press the PLAY button to return to normal speed.
TRACKING ADJUSTMENT
STILL PICTURE
TV/VCR
•
Tracking adjustment will be set automatically
(Digital Tracking function) when you start playback.
•
However when playing pre-recorded tapes or tapes recorded on units other than your own, noise lines
(black and white streaks) may appear on the playback picture. If this occurs, you can adjust the tracking control manually by pressing the CHAN-
NEL button K or L until the streaks disappear. To return to the DTR function, stop the tape once and
TV/VCR
You can view a still picture on the TV screen during playback
(the Still mode). Press the PAUSE button during playback.
Only tapes recorded in the SLP mode will show the least amount of lines.Press the PLAY button to return to playback.
NOTES:
•
You can advance the picture one frame at a time by pressing the PAUSE button during the Still mode.
•
If it is left in the Pause mode for more than five minutes, the TV/DVD/VCR will automatically switch to the Stop mode.
start playback again.
•
You can reduce the noise lines by pressing the
CHANNEL button K or L in slow mode, too.
VERTICAL HOLD CONTROL
Tracking adjustment in Slow mode will not be set automatically.
TV/VCR
In the Pause/Still mode only, when the picture begins to vibrate vertically, stabilize the picture by pressing the CHANNEL button K or L.
NOTE:
If there are video noise lines on the screen, see Tracking
- 26 -
Adjustment section.
EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 27
Make sure ...
•
TV/DVD/VCR power must be turned on.
•
Insert a prerecorded tape.
RENTAL PLAYBACK
TV/VCR
This function enables you to improve the picture quality when playing back worn cassettes such as rented tapes.
1
Select “USER’S SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “USER’S SET UP”.
Then, press the ENTER button.
SPECIAL PLAYBACK
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
AUTO REPEAT PLAYBACK
TV/VCR
The TV/DVD/VCR has the auto repeat function that allows you to repeat a tape indefinitely without touching the PLAY button.
ALL REPEAT:
Repeat playback from the beginning to the end of the tape.
BLANK REPEAT
: Repeat playback from the beginning to a blank part, which is blank for more than
10 seconds.
1
Select “USER’S SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “USER’S SET UP”.
Then, press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Set “RENTAL” to [ON]
Press the Arrow button K or L to point to “RENTAL”.
Press the ENTER button until [ON] appears.
– USER’S SET UP –
B
RENTAL
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[ON]
[OFF]
[OFF]
[HIFI]
[STEREO]
3
Exit the Rental setting
Press the SETUP button on the remote control to return to the TV mode.
2
Select “ALL” or “BLANK”
Press the Arrow button K or L to point to “REPEAT PLAY”.
Press the ENTER button repeatedly until your desired selection [ALL] or [BLANK] appears.
– USER’S SET UP –
RENTAL
B
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[ALL]
[OFF]
[HIFI]
[STEREO]
3
Exit the Repeat Play setting
Press the SETUP button on the remote control to return to the TV mode.
4
Start playback
Press the PLAY button to start playback. “RENTAL
PLAY B” appears.
•
Once you select the Rental mode, it stays in effect even after you turn off the TV/DVD/VCR.
TO CANCEL THE RENTAL MODE
Repeat steps [1] and [2], select [OFF] using the
ENTER button on the remote control. Press the
SETUP button on the remote control to return to TV mode.
If there is a power failure of any kind, the tv/vcr/dvd will retain its memory for this feature.
4
Start playback
Press the PLAY button to start the Repeat Play.
“REPEAT PLAY B” appears.
•
Once you select the Repeat Play mode, it stays in effect even after you turn off the TV/DVD/VCR.
•
If the Rental mode is set [ON], the “RENTAL
PLAY B” display has priority.
TO CANCEL THE REPEAT PLAY MODE
Repeat steps [1] and [2], select [OFF] using the
ENTER button on the remote control. Press the
SETUP button on the remote control to return to TV mode.
If there is a power failure of any kind, the
TV/DVD/VCR will retain its memory for this feature.
- 27 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 28
SEARCH
Make sure ...
•
TV/DVD/VCR power must be turned on.
•
Insert a tape.
ZERO RETURN
TV/VCR
This function allows you to search easily a beginning point that you want to review by rewinding or fast forwarding.
NOTE:
Zero Return WILL NOT work on a blank tape or a blank portion of a tape.
TIME SEARCH
TV/VCR
The Time Search function makes it possible to quickly advance the tape to your desired position simply by entering the exact amount of playback time you want to skip.
NOTES:
•
Time Search can be set up to a maximum of 9 hours 50 minutes (9:50) by 10 minutes at a time.
•
This function will not operate in recording mode.
•
This function is not operative when a cassette tape is not inserted in the TV/DVD/VCR.
In the example below: To watch a program after 2 hour 50 minutes from the present position, in either direction.
1
Stop a tape at your desired point
Rewind or fast forward the tape to the beginning point at which you want to review.
2
Reset the counter to 0:00:00
Press the C.RESET button repeatedly.
1
Insert a tape.
3
Begin recording or playback
Press the RECORD or PLAY button.
Press the STOP button when recording or playback is completed.
2
Select “TIME SEARCH” mode
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “TIME SEARCH”.
Then, press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
B
TIME SEARCH
INDEX SEARCH
4
To activate “ZERO RETURN” mode
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “ZERO RETURN”.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
B
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Then, press the ENTER button.
The counter will appear on the TV screen.
The tape will automatically stop when the counter returns to 0:00:00.
3
Enter your desired time
Press the Arrow button K or L until your desired time appears.
(Example: “2:50” stands for 2 hours
50 minutes)
TIME SEARCH
2 : 50
If you wish to cancel the Time
Search at this point, press the SETUP button on the remote control.
4
Begin Time Search
By pressing the Arrow button s or B, the
TV/DVD/VCR will rewind or fast forward to the specified point.
The time counts down as the searching progresses.
When 0:00 is reached, the tape will start playback automatically.
- 28 -
TO CANCEL THE TIME SEARCH at this point
Press the STOP/EJECT button on the TV/DVD/VCR or the STOP button on the remote control. This will delete the selected time.
EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 29
INDEX SEARCH
TV/VCR
This feature provides a method of indexing the starting point so that it can be easily returned to in either fast forward or rewind mode.
•
The index mark will be made automatically when the REC button is pressed. It will also be marked at the starting point of Timer recording and OTR.
•
The index mark will not be recorded if the PAUSE button is pressed and released during recording.
•
The time gap between making the index marks on the tape should be greater than 1 minute for SP recording, 2 minutes for LP recording and 3 minutes for SLP recording.
•
In some cases, the index mark at the beginning of video tape cannot be detected.
Example: You are watching program number 4 and want to fast forward to program number 7. You must skip three programs.
1
Select “INDEX SEARCH”
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “INDEX SEARCH”. Then, press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
B
INDEX SEARCH
2
Enter your desired number
Press the Arrow button K or L until the number of programs that you want to skip appears.
(Example: “03” for 3 programs)
INDEX SEARCH
0 3
•
The Index Search mode will be canceled if the procedures are not activated in 30 seconds.
3
Begin Index Search
Press the Arrow button s or B. The TV/DVD/VCR begins rewinding or fast forwarding to the beginning of desired program.
NOTE: Every time an index signal is skipped, the number in the program indicator decreases by one.
CURRENT PLAYBACK PROGRAM
Beginning of tape End of tape
4
Pro.1
Pro.2
Pro.3
Pro.4
Pro.5
Pro.6
Pro.7
3 2 1 1 2 3
INDEX MARK
4
After Index Search
When the preset program is reached, the
TV/DVD/VCR will start playback automatically.
•
A video cassette must be inserted in the
TV/DVD/VCR for this function to work.
•
The number of Index Searches can be set up to 20.
•
This function will not operate in the recording mode.
•
When you want to cancel the Index Search while in progress, press the STOP button.
SPECIAL FEATURES
REAL TIME TAPE COUNTER
TV/VCR
This shows the elapsed recording or playback time in hours, minutes, and seconds. (The displayed time will not change on a blank tape or blank portions on the tape.)The “–” indication will appear when the tape has rewound further than “0:00:00” on the tape counter.
AUTO REWIND-EJECT
TV/VCR
•
When the end of a tape is reached during recording, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding finishes, the TV/DVD/VCR will eject the tape and turn itself to off.
•
This function is operative when Repeat Play is set to the [OFF] position.
•
The tape will not auto-rewind during timer recording or One Touch Recording.
- 29 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 30
RECORDING
Make sure ...
•
TV/DVD/VCR power must be turned on.
•
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)
NOTES:
•
This TV/VCR/DVD will ONLY record and view the same channel.
•
This TV/VCR/DVD cannot record the contents from the built-in DVD.
NORMAL RECORDING
TV/VCR
You can ONLY watch the same TV program that is being recorded.
1
Select the channel to be
CH 10
recorded
Press the number buttons on the remote control or the CHANNEL button K or L.
Remember: If the TV/DVD/VCR is connected to a cable box or satellite box, the TV/DVD/VCR must be on CH3 or CH4, then the channel to be recorded must be selected on the cable box or satellite box.
SKIPPING UNWANTED
SCENES DURING RECORDING
TV/VCR
Press the PAUSE button to temporarily stop recording.
Press the PAUSE or RECORD button to resume recording.
PAUSE
NOTES:
SP
•
After five minutes, the TV/DVD/VCR will automatically switch to the Recording mode to prevent tape damage.
•
If “CLOSED CAPTION (ON)” is selected, the On-
Screen Display will appear for 5 seconds, then disappear.
2
Select the tape speed
Press the SPEED button to select the desired tape speed (SP/ SLP).
SP
3
Begin recording
Press the RECORD button.
REC
SP
4
Stop recording
Press the STOP button when recording is completed.
- 30 EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 31
OTR (One Touch Recording)
TV/VCR
This function enables you to set a recording length simply by pressing the REC/OTR button on the
TV/DVD/VCR.
Make sure ...
•
TV/DVD/VCR power must be turned on.
•
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)
NOTES:
•
This function CANNOT be done from the remote control.
•
Recording starts immediately when the REC/OTR button is pressed.
•
When the REC/OTR button is pressed 18 times, the
TV/DVD/VCR returns to the Normal Recording mode.
•
To stop the OTR operation, press the STOP button on the TV/DVD/VCR or on the remote control.
•
To show the remaining time, press the DISPLAY button on the remote control so that “OTR” appears on the TV screen. (It will show up momentarily then disappear.)
•
Recording stops when 0:00 is reached.
•
Please note that in the SLP mode maximum recording time, assuming the tape is started at the beginning, is 8 hours using T-160 (or 6 hours using T-120).
•
If the tape runs out before the end time, the
TV/DVD/VCR will switch to the Stop mode immediately, ejects the tape and turns itself off.
•
If you press the POWER button during OTR, the
TV/DVD/VCR continues recording until the selected length is reached.
Push(es) Display
1 push
2 pushes
3 pushes
0:30
1:00
Recording length
(normal recording)
30 minutes
60 minutes
17 pushes 8:00
REC/OTR REW PLAY F.FWD
STOP
EJECT
HEADPHONE VIDEO L AUDIO R
480 minutes
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
TV/VCR
You can make copies of video tapes made by friends or relatives for your enjoyment.
You can not copy a DVD to a videotape.
WARNING: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.
Connect your TV/DVD/VCR and a Source (Playing)
VCR using the following diagram.
[The TV/DVD/VCR]
[Fig.8]
[Ex: Source (playing)
VCR or camcorder]
1
Select the channel to be recorded
Press the number buttons on the remote control or the CHANNEL button K or L.
Remember: If the TV/DVD/VCR is connected to a cable box or satellite box, the TV/DVD/VCR must be on CH3 or CH4, then the channel to be recorded is selected on the cable box or satellite box.
2
3
Select the tape speed
Press the SPEED button to select the desired tape speed (SP/ SLP).
Begin OTR
OTR(2 : 30)
Press the REC/OTR button on the
TV/DVD/VCR as many times as needed. The recording length will be determined by the number of times you press the REC/OTR button. Each
SP additional push will increase the recording time by 30 minutes. It is set up to 8 hours.
Audio/Video adapter cable
(not supplied)
AUDIO
L
OUT IN
R
VIDEO
OUT IN
- 31 -
1)Insert a pre-recorded video cassette into the Source
(Playing) VCR or camcorder.
2)Insert a blank video cassette, or one you want to record over, into the TV/DVD/VCR’s cassette compartment.
3)Press the SPEED button on remote control for the
TV/DVD/VCR to select the desired recording speed (SP/SLP).
4)Press the CHANNEL button K or L on the
TV/DVD/VCR until “AUX” appears on the screen.
5)Press the RECORD button on the TV/DVD/VCR.
6)Begin playback of the tape in the source (Playing)
VCR or camcorder.
NOTE: For best results during copying, use the
TV/DVD/VCR’s front panel controls whenever possible. The remote control might affect the source
(Playing) VCR’s playback operation.
EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 32
TIMER
AUTOMATIC TIMER
RECORDING
TV/VCR
You may set the TV/DVD/VCR to start and end a recording while you are away. You can set 8 programs to record on specific days, daily or weekly within a 1 year period.
In the example below, the timer is being set to record:
DATE: July 4th, 2003
SETTING TIME: from 7:30PM to 8:50PM
CHANNEL: CH61
TAPE SPEED: SP
Make sure ...
•
If a cable box or satellite box is connected with the
TV/DVD/VCR you will be limited to record only one channel. And the channel selector on the
TV/DVD/VCR must be selected to the output channel of the boxes CH 3 or CH 4 and then the actual channel to be recorded must be selected on the boxes.
•
Clock must be set to the correct time and date before setting the timer.
•
TV/DVD/VCR power must be turn on to program it.
•
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)
•
The channel you want to record is properly set in advance. (See page 16.)
Avoid over lap of programs ...
There is a chance that a program will not be recorded. when programs overlap;
•
The program with an earlier start has priority.
•
Once the earliest program finishes, the overlapping programs will begin recording in sequence.
•
The illustration below demonstrates the sequence of recordings.
Program 1
Program 2
Program 3
10:00AM - 11:00AM
9:00AM - 10:00AM
9:30AM - 12:00PM
Recording Sequence
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
9:30AM-12:00PM
9:00AM 10:00AM 11:00AM
*Recording period is SHADED
12:00PM
1
Select “TIMER PROGRAMMING”
Press the SETUP button on the remote control.
Confirm “TIMER PROGRAM-
MING” is pointed by pressing the
Arrow button K. And press the
ENTER button.
- TV/VCR SETUP -
B
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
•
If you have not yet set the clock, “MANUAL
CLOCK SET” appears. If so, follow stops [3] to
[8] on page 17. Then set the timer recording.
2
Select your desired program position (1~8)
Press the Arrow button K or L to select the desired program position.
Then, press the Arrow button B.
– TIMER PROGRAMMING –
CH DATE BEGIN END
B
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
3
Set the channel number
Press the Arrow button K or L until the desired channel number
– TIMER PROGRAMMING –
CH DATE BEGIN END appears. (Example: CH61)
Then, press the Arrow button B.
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
B
61 -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
Remember: If the TV/DVD/VCR is connected to a cable box or satellite box, the
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
TV/DVD/VCR must be on CH3 or CH4, then the channel to be recorded is selected on the cable box or satellite box.
4
Select once, every day or weekly recording
For once recording :
– TIMER PROGRAMMING –
Press the Arrow button K (up) until the desired date appears.
(Example: “7/04” for July 4th).
Then, press the Arrow button B.
CH DATE
B
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
61 7/04 FRI -:- -
- -/- - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
BEGIN END
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
For every day recording : To record a TV program at the same time on the same channel every day.
(Example: Monday through Sunday)
– TIMER PROGRAMMING –
Press the Arrow button L (down) until “EVRY DAY” appears.
Then, press the Arrow button B.
CH DATE BEGIN END
B
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
61 EVRY DAY -:- -
- - -/- - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
- 32 -
For weekly recording : To record a TV program at the same time on the same channel every week.
(Example: every Monday)
– TIMER PROGRAMMING –
Press the Arrow button L (down) until “EVRY” and your desired day of the week appear together.
Then, press the Arrow button B.
CH DATE BEGIN END
B
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
61 EVRY MON -:- -
- - -/- - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 33
5
Set beginning hour
– TIMER PROGRAMMING –
Press the Arrow button K or L until the desired hour appears.
(Example: “ 7, PM” for 7:30PM)
Then, press the Arrow button B.
CH DATE BEGIN END
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
P
M B
61 7/04 FRI 7:12
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
6
Set beginning minute
– TIMER PROGRAMMING –
Press the Arrow button K or L until the desired minute appears.
(Example: “30” for 7:30PM)
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
P
M B
61 7/04 FRI 7:30
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
Then, press the Arrow button B.
CH DATE BEGIN END
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
7
Set end hour
– TIMER PROGRAMMING –
CH DATE BEGIN END
Press the Arrow button K or L until the desired hour appears.
(Example: “8, PM” for 8:50PM)
Then, press the Arrow button B.
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
B
61 7/04 FRI 7:30
P
M
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:30
M
- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
TIMER PROGRAM EXTENSION
TV/VCR
To shift the time schedule of an automatic timer recording.
1)Press the POWER button.
2)Repeat step [1] on page 32.
3)Press the RECORD button and select the desired program using the Arrow button K or L.
4)Press the RECORD button again.
Each additional push will shift forward the begin/end time for recording by 10 minutes. When the recording is already in progress, each additional push will shift forward the end time only. If you want to cancel while setting, press the PAUSE button on the remote control. The recording time returns to the original time.
NOTE: When you shift forward the time schedule during recording, the recording speed will automatically be set to the SLP mode.
5)Press the ENTER or RETURN button to exit the setting menu. Then press the SETUP button on the remote control to return to original mode.
8
Set end minute
Press the Arrow button K or L until the desired minute appears.
(Example: “50” for 8:50PM)
Then, press the Arrow button B.
– TIMER PROGRAMMING –
CH DATE BEGIN END
B
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
61 7/04 FRI 7:30
P
M
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:50
P
M
- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
9
Set the tape speed
Press the Arrow button K or L until the desired tape speed appears. (Example: SP)
– TIMER PROGRAMMING –
CH DATE BEGIN END
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
P
M B
61 7/04 FRI 7:30
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
P
M
8:50 SP
-:- - - -
-:- - - -
-:- - - -
-:- - - -
10
Finish setting the program
Press the ENTER or RETURN button. The program is now completed.
•
To set another program, repeat steps [2] to [10].
•
Press the SETUP button on the remote control to return to original mode.
TO CORRECT A PROGRAM
•
While setting a program; press the Arrow button s to go back one step and enter the correct numbers using the Arrow button K or L.
•
After setting a program;
1)Press the POWER button.
2)Repeat steps [1] - [2] on page 32.
3)Press the Arrow button B (or press the Arrow button s to go back one step) until the part you want to correct begins flashing, then make the changes pressing the Arrow button K or L.
4)Press the POWER button to set automatic timer recording.
11
Set the timer
Press the POWER button to set automatic timer recording. The RECORDING indicator lights up.
•
You must turn off the TV/DVD/VCR to activate automatic timer recording.
If power is not turned off and you continue watching TV, “TIMER REC STANDBY” starts flashing on the TV screen 2 minutes before the programmed start time.
TO CANCEL AN AUTOMATIC TIMER
RECORDING
•
After setting a program;
1)Press the POWER button.
2)Repeat steps [1] ~ [2] on page 32 and select a program you want to cancel.
3)Press the C.RESET button.
4)Press the SETUP button on the remote control to return to TV mode.
•
While recording is in progress;
1)Press the POWER button.
2)Press the STOP/EJECT button on the
TV/DVD/VCR.
- 33 EN
1C29
TD900UA(P01-35).QX33 03.9.1 11:36 AM Page 34
TO CHECK THE BEGIN/END TIME
1)Press the POWER button so that the RECORDING indicator goes off.
2)Press the SETUP button on the remote control.
3)Confirm “TIMER PROGRAMMING” is pointed.
4)Press the ENTER button. The details of programs appear on the TV screen.
5)Press the SETUP button on the remote control to return to TV mode.
HINTS FOR AUTOMATIC
TIMER RECORDING
TV/VCR
•
Make sure the channel you want to record is properly set in advance.
•
It is not necessary to press the RECORD button for timer recording.
•
Recording begins automatically at the Start time.
•
The display will not be turned on when the programmed recording begins. To watch the currently recorded TV program or to play a DVD disc, press the POWER button to turn on the display and use the SELECT button to choose the TV/VCR mode or the DVD mode.
•
The erase-prevention tab on the cassette must be in place (or you must put tape over the hole).
•
If the erase-prevention tab is removed, the cassette will be ejected when the POWER button is pressed to off.
•
If the tape runs out before the end time, the
TV/DVD/VCR will switch to the Stop mode immediately, and the tape will be ejected.
3
Auto Return will begin
When all the timer recordings are completed, the
TV/DVD/VCR will rewind to the beginning of the recorded program(s).
NOTE:
•
If you press the POWER button while tape is rewinding, the Auto Return will stop.
4
Watch the recorded program
Press the PLAY button.
TO CANCEL THE AUTO RETURN
MODE
Repeat steps [1] and [2], select [OFF] using the
ENTER button.
If there is a power failure of any kind, the
TV/VCR/DVD will retain its memory for this feature.
SLEEP TIMER
TV/VCR
The Sleep Timer function turns off the
TV/DVD/VCR without using the POWER button after a desired period of time.
NOTE:
•
This function does not operate during Recording mode.
1
Select “SLEEP TIMER”
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears.
AUTO RETURN
TV/VCR
With this feature, after timer recording is finished, the beginning of the recorded program(s) can be searched for automatically.
2
Set sleep time
Press the SLEEP button until your desired sleep time appears.
Each additional push will increase the time by 30 minutes up to 120 minutes.
SLEEP 120 MINUTES
After 5 seconds, exit the Sleep Timer setting.
1
Select “USER’S SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “USER’S SET UP”.
Then, press the ENTER button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Set “AUTO RETURN” to [ON]
Press the Arrow button K or L to point to “AUTO RETURN”.
Press the ENTER button until [ON] appears.
– USER’S SET UP –
B
RENTAL
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[ON]
[HIFI]
[STEREO]
- 34 -
TO CANCEL THE SLEEP TIMER
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears. Press the SLEEP button until “SLEEP 0 MINUTES” appears.
EN
1C29
TD900UA(P01-35).QX33 03.8.29 4:50 PM Page 35
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:
When the Closed Caption mode is OFF:
•
Counter mode: After 5 seconds, only the counter remains. To clear it, press the DISPLAY button.
•
Clock mode: After 5 seconds, only the clock and the channel number remain. To clear them, press the DISPLAY button.
When the Closed Caption mode is ON:
•
The On Screen Display disappear after 5 seconds.
•
This is true even if the MUTE button is pressed, or the PAUSE button is pressed while recording.
OFF mode Counter mode
STOP
Clock mode
STOP 5:40PM
CH2
OFF mode Clock/Counter mode
STOP 5:40 PM
CH2
SP COUNT 0:12:34
After 5 seconds
SP
After 5 seconds
5:40PM
CH2
SP COUNT 0:12:34
COUNT 0:12:34
Counter remains
Clock & Channel remains
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels with letters or letter-number combinations. Please check with your local cable company. The following is a chart of common cable channel designations.
CATV channel
TV Display
5A
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
A
14
B
15
CATV channel
TV Display
C
16
D
17
E
18
F
19
G
20
H
21
I
22
J
23
K
24
L
25
M
26
N
27
O
28
P
29
Q
30
CATV channel
R S T U V W W+1 W+2 W+3 W+4 W+5 W+6 W+7 W+8 W+9
TV Display
CATV channel
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
TV Display
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
CATV channel
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
TV Display
CATV channel
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
TV Display 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90
CATV channel
TV Display
W+55 W+56 W+57 W+58
91 92 93 94
A-5
95
A-4 A-3 A-2 A-1 W+59 W+60 W+61 W+62 W+63 W+64
96 97 98 99 100 101 102 103 104 105
CATV channel W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
TV Display
CATV channel
TV Display
106 107 108 109 110
W+80 W+81 W+82 W+83 W+84
121 122 123 124 125
111 112 113 114 115 116 117 118 119 120
- 35 EN
1C29
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 36
DVD SECTION
ABOUT THE DISCS
PLAYABLE DISCS DISC TYPES
The following discs can be played back on this
TV/DVD/VCR.
¡
DVD video
¡
DVD-R/RW*
¡
DVD+R/RW*
¡
Audio CD
¡
CD-R/RW*
¡
MP3*
* Depending on the types or the writing method of the medium some discs can not be played.
• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs made on personal computers, or on DVD recorders may not be played back properly due to the factors such as scratches, dirt or special properties of the disc.
• Discs made on personal computers may not be played back properly due to the different environment or the settings of the application you use. We recommend always to use the standardized, rightly formatted discs.
(Please contact the sales agency for more detail).
[DVD]
Data on a DVD is divided into sections called "titles", and then into subsections called "chapters", each of which is given a title or chapter number. Playback conditions are preset on some DVD video discs, and these playback conditions take priority over user operations on this player. If a function you selected does not run as desired, refer to the manual accompanying the disc.
Example
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
This player conforms to the NTSC color system. You cannot play discs recorded in other color systems such as
PAL or SECAM.
¡ Some discs include region codes as shown below.
[AUDIO CD]
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
Example
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6
¡ The number inside the symbol refers to a region of the world, and a disc encoded in a specific region format can only be played back on TV/DVD/VCR with the same region code.
The following discs cannot be played back on this
TV/DVD/VCR.
¡
DVD with region codes other than 1 or ALL.
¡
DVD-ROM
¡
DVD-RAM (Never play back, otherwise malfunction may result.)
¡
CD-ROM
¡
VSD
¡
CDV (Only plays back the audio part.)
¡
CD-G (Only plays back the sound.)
¡
CD-I (Never play back, otherwise malfunction may result.)
¡
SACD
¡
Photo CD (Never play back, otherwise malfunction may result.)
¡
Video CD (Never play back, otherwise malfunction may result.)
Any other discs without compatibility indications.
[MP3]
Data on an MP3 is divided into sections called "groups", and then into subsections called "tracks", each of which is given a group or track number.
Example
Group 1
Track 1 Track 2 Track 3 Track 4
Group 2
Track 1 Track 2
– 36 –
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 37
PLAYING A DISC
BASIC PLAYBACK
DVD-V CD
Getting started
¡ Turn on the power of amplifier and any other components, if necessary.
1
Press the POWER button.
¡ The power will turn on.
2
Press the OPEN/CLOSE button to open disc loading tray.
3
Place the chosen disc in the tray, with the label facing up.
GENERAL FEATURES
DVD may contain menus to navigate the disc and access special features. Press the appropriate number buttons or use the Arrow buttons (L/K/s/B) to highlight your selection in the DVD main menu and press the ENTER button to confirm.
NOTES
¡
Select DVD mode by pressing the SELECT button on the remote control. Then, operate the DVD functions.
¡ Unless stated, all operations described are based on remote control use. Some operations can be carried out using the menu bar on the TV screen.
DISC MENU
DVD-V
1
Press the DISC MENU button.
¡
The DVD main menu will appear.
4
Press the PLAY button.
¡ The tray will close automatically, and playback will then start from the first chapter or track of the disc.
If the playback does not start automatically, press the PLAY button.
¡ When you playback the DVD which a title menu is recorded, it may appear on the screen. In this case, refer to “TITLE MENU”.
2
If the feature is not available, may appear on the TV screen.
symbol
3
If disc menu is available on the disc, audio language, subtitle options, chapters for the title and other options will appear for selection.
4
Press the Arrow buttons (L/K/s/B) to
select an item, and the ENTER button to confirm selection.
5
Press the STOP button to stop playback.
TITLE MENU
NOTES
¡ When the DVD mode has been switched to the
TV/VCR mode, the DVD mode shuts down first and then TV picture and sound appears in about 4 seconds.
Similarly, when the POWER button is pressed to turn off in the DVD mode, this mode shuts down first and then the TV/DVD/VCR’s power is turned off.
¡
A “prohibited icon” may appear at the top-right on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD or the disc.
¡
With DVDs that use titles for playback program signals, playback may start from the second title, or it may skip these titles.
¡
During the playback of a two layered disc, pictures may stop for a moment. This happens when the 1st layer switches to the 2nd layer. This is not a malfunction.
1
Press the TITLE button.
¡ The title menu will appear.
2
If the feature is not available, may appear on the TV screen.
DVD-V symbol
3
Press the Arrow buttons (L/K/s/B) to
select an item, and the ENTER button to confirm selection.
CALLING UP A MENU SCREEN
DURING PLAYBACK
For DVD-Vs
¡
Press the DISC MENU button to call up the DVD menu.
¡ Press the TITLE button to call up the title menu.
NOTE
¡ Contents of menus and corresponding menu operations may vary between discs. Refer to the manual accompanying the disc for details.
– 37 –
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 38
RESUME
SLOW FORWARD /
SLOW REVERSE
DVD-V CD
DVD-V
1
During playback, press the STOP button.
¡
Resume message will appear on the TV screen.
2
Press the PLAY button, playback will resume from the point at which playback was stopped.
¡ To cancel resume, press the STOP button twice.
¡ If turn off the TV/DVD/VCR, resume function will be cancelled.
PAUSE
1
During playback, press the PAUSE button.
2
Press and hold down the FWD
g
or REV
h
button for a few seconds.
3
Each press and hold down the FWD
g
or
REV
h
button repeatedly to select the required speed: 1/16, 1/8, 1/2 of the normal playback.
4
To return to normal playback, press the
PLAY button.
DVD-V CD
1
During playback, press the PAUSE button.
¡ Playback will pause and sound will be muted.
2
To continue playback, press the PLAY button.
Note for using buttons on the main unit:
Press the PAUSE button, then, press and hold down the
SKIP G / SEARCHg buttons or the SKIPH
/SEARCHh buttons on the TV/DVD/VCR for a few seconds to begin Search in 1/16 speed of the normal playback. Press and hold down again to change speed to 1/8. Repeat this procedure to change to 1/2.
STEP BY STEP PLAYBACK
DVD-V
ZOOM
1
During playback, press the PAUSE button.
¡
Playback will pause and sound will be muted.
DVD-V
2
The disc goes forward by one frame each time the PAUSE button is pressed.
3
To exit step by step playback, press the
PLAY button.
The Zoom function allows you to enlarge the video image and to pan through the enlarged image.
1
Press the ZOOM button during playback.
¡
Playback will continue.
FAST FORWARD/REVERSE
SEARCH
DVD-V CD MP3
2
Press the ZOOM button repeatedly to select the required zoom factor: ZOOM1, ZOOM2,
ZOOM3, or OFF.
1
During playback, press and hold down the FWD
g
or REV
h
button for a few seconds.
2
Each press and hold down the FWD
g
or
REV
h
button repeatedly to select the
¡
required speed: x2, x8, x50, x100.
For audio CDs, the speed is fixed at
×16.
¡ For MP3, the speed is fixed at
×8.
3
To return to normal playback, press the
PLAY button.
Note for using buttons on the main unit:
During playback, press and hold down the SKIP G /
SEARCHg buttons or the SKIPH /SEARCHh buttons on the TV/DVD/VCR for a few seconds to begin
Search in x2 speed. Press and hold down again to change speed to x8. Repeat this procedure to change to x50 and x100.
– 38 –
3
Use the Arrow buttons (
K / L / s / B
) to move the zoomed picture across the screen.
4
To exit zoom mode, press the ZOOM button to OFF.
NOTES
¡ Zooming function does not work while disc menu is shown.
¡ Zooming function is not available on some discs.
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 39
SEARCH FUNCTION
TRACK SEARCH
CD
TIME SEARCH
DVD-V CD
There are three ways to begin playback on an Audio
CD at a specific Track.
Using the Number buttons on the remote control
1
Press the Number buttons to enter the desired Track number.
¡ Playback will start at the selected track.
¡ For single digit tracks (1-9), press a single number
(eg. track 3, press 3).
¡ To play track 26, press +10, 2, 6.
1
During playback, press the SEARCH MODE button three times (CD: twice) to display the
Time Search on the TV screen.
2
Within 30 seconds, enter a desired disc time using the Number buttons on the remote control.
¡ Playback will start at the specified time.
¡ Press the CLEAR button to erase the incorrect input.
MARKER SETUP SCREEN
DVD-V CD
Using the SEARCH MODE button
1
Press the SEARCH MODE button.
¡ The track search display appears.
2
Within 30 seconds, select a desired track number using the Number buttons on the remote control.
¡ For single digits press 0 first.
¡ Playback will start at the selected track.
Use markers to memorise your favorite places on a disc.
1
Press the SEARCH MODE button four times
(CD: three times) during playback.
¡
The display screen and Markers will appear on the
TV screen.
Using the SKIP H G buttons
During playback, press the SKIP G button to move the next track. Press it repeatedly to skip subsequent tracks. Press the SKIP H button to go back to beginning of the current track. Press it repeatedly to go to the previous tracks.
¡ If the SKIP button is pressed while the playback is paused, the playback will be paused again after skipping to the next track.
NOTE
¡ The SKIP H G buttons are not available when playback is stopped.
TITLE / CHAPTER SEARCH
DVD-V
1
Press the SEARCH MODE button once for the Chapter search, twice for the Title search during playback.
/2
2
Press the Arrow buttons (s/ B) to select 1,
2, 3, 4, 5, 6, 7, 8, 9, or 10 and ensure that “- :
- - : - -” appears in the display.
3
When reaches the desired point, press the
ENTER button.
¡
The Title or Track and elapsed playing time will appear in the TV screen.
4
To return to the Marker later, press the
SEARCH MODE button four times (CD: three times) during playback and the Arrow but-
tons (s/ B) to choose the desired marker,
then press the ENTER button.
NOTES
¡
Opening the disc tray or turning off the power or select AC at step 2 and press the ENTER button will erase all Markers.
¡ To clear a marker, using the Arrow buttons (s/ B), position the cursor on to the marker number to be cleared and press the CLEAR button.
¡
You can mark up to 10 points.
2
Enter the desired chapter/title number using the Number buttons on the remote control.
¡ Playback will start at the selected Chapter or Track.
¡
Press the CLEAR button to erase the incorrect input.
¡ For single digits press 0 first.
5
Press the SEARCH MODE or RETURN button to exit.
– 39 –
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 40
SPECIAL PLAYBACK FUNCTION
REPEAT
REPEAT is available only during playback.
REPEAT TITLE / CHAPTER
DVD-V
PROGRAM
CD
You may determine the order in which tracks will play.
To activate the repeat function, press the
REPEAT button during playback.
¡
The repeat mode changes as described below every time you press the button.
CHAPTER TITLE
(current chapter repeat) (current title repeat)
TRACK
(current track repeat)
ALL
(entire disc repeat)
OFF
(repeat off)
NOTES
¡
Repeat Title/Chapter is not available with some scenes.
¡
The REPEAT setting will be cleared when moving to other title or chapter.
REPEAT TRACK
CD
To activate the repeat function, press the
REPEAT button during playback.
¡ The repeat mode changes as described below every time you press the button.
OFF
(repeat off)
NOTES
¡
Repeat setting will be cleared when moving to other track.
¡
Repeat playback does not function during repeat A-B playback.
REPEAT A-B
DVD-V CD
1
3
In stop mode, press the MODE button.
¡
The PROGRAM screen will appear.
2
Press the Arrow button
▲ or ▼ to select a
track, then press the
ENTER button.
¡ Press the CLEAR button to erase the most recently entered program.
TOTAL
Repeat step 2 until you have selected all the tracks you want to play in the program.
4
Press the PLAY button to play the programmed tracks.
NOTES
¡ While the program is being played back, the STOP works as follows.
¡ Press the STOP button once and then the PLAY button again, playback will restart from the point where the STOP button was pressed. (Program continued)
¡ Press the STOP button twice and then the PLAY button again, playback will restart from the track in the usual way. (Program cleared)
¡ Up to 99 programs can be entered.
¡ If you like to repeat the current track in the program, press the REPEAT button repeatedly until
TRACK appears during playback. If you like to repeat the entire program press the REPEAT button repeatedly until ALL appears during playback.
RANDOM PLAYBACK
¡
1
Press the REPEAT A-B button at your chosen starting point.
A- appears briefly on the TV screen.
CD
This shuffles the playing order of tracks instead of playback in the sequence.
2
Press the REPEAT A-B button again at your chosen end point.
¡
A-B appears briefly on the TV screen, and the repeat sequence begins.
1
In stop mode, press the MODE button twice.
¡ RANDOM screen appears.
RANDOM
CD [AUDIO] TOTAL 0:45:55
RANDOM PROGRAM
- - no indication - -
PLAY
3
To exit the sequence, press the REPEAT A-
B button.
NOTES
¡
¡
¡
The repeat A-B section can only be set within the current title (for DVDs), or current track (for audio CDs).
Repeat A-B is not available with some scenes in DVD.
To cancel the A point which was set, press the
CLEAR button.
¡ Repeat A-B playback does not function during title, chapter, track or all repeat playback.
– 40 –
2
Press the PLAY button to start random playback.
NOTE
¡
If you like to repeat the current track in the random selection, press the REPEAT button repeatedly until
TRACK appears during playback. If you like to repeat the entire random selection press the
REPEAT button repeatedly until ALL appears during playback.
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 41
PLAYING A MP3 DISC
MP3 PLAYBACK TRACK SELECTION
MP3 MP3
When a CD with MP3 files is in the TV/DVD/VCR, the MP3 menu will appear on the TV screen in stop mode.
1
Press the SEARCH MODE button during playback.
¡ The FILE LIST will appear.
1
In stop mode, press the Arrow buttons
(
K
/
L
) to select the desired group track.
¡ If a group is selected, press the Arrow
B or ENTER button to go on to the track selection screen. Press the Arrow buttons (
K
/
L
) to choose a track, then press the ENTER button.
¡ If a track is selected, press the ENTER button to start playing tracks. Starting from the one you’ve just chosen the subsequent tracks will be played.
¡ Choose FIRST PLAY to start playback from the beginning of the listed tracks.
¡ Press the TITLE button to return to the first item.
2
Select a desired track using the Arrow buttons (
K / L /s/B
).
¡ Press the Arrow button
B when you want to go to the next hierarchy.
¡ Press the Arrow button s when you want to go back to the previous hierarchy.
3
Press the PLAY button to start playback.
NOTES
¡ Press the SEARCH MODE button to exit.
¡ Some selections may take a while to be recognized.
PROGRAM
MP3
2
Press the STOP button to stop playback.
NOTES
¡ Folders are known as Groups; files are known as
Tracks.
¡ MP3 files are accompanied by
3 icon.
¡ Maximum of 255 folders can be recognized.
¡ Maximum of 256 files can be recognized.
¡ Up to 8 hierarchies can be created.
This player recommends the use of files recorded at the below specifications:
¡ Sampling frequency: 44.1kHz or 48kHz
¡ Constant bit rate: 112kbps ~ 320kbps.
This feature allows you to program an MP3 disc to play in a desired sequence.
1
In stop mode, press the MODE button.
¡
The PROGRAM screen will appear.
2
Select a desired track using the Arrow buttons (
K
/
L
/s/B
). Then, press the ENTER button.
¡ Press the Arrow button
B when you want to go to the next hierarchy.
¡ Press the Arrow button s when you want to go back to the previous hierarchy.
¡ Press the CLEAR button to erase the most recently entered program.
3
Repeat step 2 until you have selected all the
Tracks you want to play in the program.
4
Press the PLAY button to start programmed playback.
RANDOM PLAYBACK
MP3
1
In stop mode, press the MODE button twice.
¡
RANDOM screen appears.
– 41 –
2
Press the PLAY button to start random playback.
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 42
CHANGING THE SETTINGS
SUBTITLE LANGUAGE CAMERA ANGLE
DVD-V
The DVD allows you to select a language for subtitles during DVD disc (if available) playback.
DVD-V
Some DVD discs contain scenes which have been shot simultaneously from various angles. You can change the camera angle when the ( ) icon appears on the screen.
1
Press the SUBTITLE button during playback.
2
Press the SUBTITLE button repeatedly to select your desired subtitle language.
¡
The subtitle language will be displayed on the display bar at the top of the screen.
1
Press the ANGLE button during playback.
¡ The selected angle will be displayed on the display bar at the top of the screen.
3
To turn off subtitles, press the SUBTITLE button repeatedly until OFF appears.
NOTES
¡
Some discs allow audio language setting/subtitle language setting on the disc menu. (Operation varies between discs,
¡ so refer to the manual accompanying the disc.)
If the desired language is not shown after pressing the SUBTITLE button several times, the disc does
¡ not have subtitles in that language.
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Subtitle language setting. If you choose any other languages, ‘---’ will be displayed instead.
(Refer to page 44.)
2
Press the ANGLE button repeatedly to select your desired angle.
BLACK LEVEL SETTING
DVD-V
Adjust the Black Level Settings to make the black parts of the picture brighter.
1
Press the MODE button during playback.
ON
AUDIO LANGUAGE
DVD-V
2
Press the ENTER button to switch OFF.
ON: Makes the dark parts brighter.
OFF: Shows the original picture as recorded.
The TV/DVD/VCR allows you to select a language during DVD disc (if multi language available) playback.
3
Press the MODE button twice or the
RETURN button to exit.
1
Press the AUDIO button during playback.
2
Press the AUDIO button repeatedly to select your desired language.
NOTE
¡ Pressing the AUDIO button may not work on some
DVDs with multiple audio languages (e.g. DVDs which allow audio language setting on the disc menu).
VIRTUAL SURROUND
DVD-V CD MP3
You can enjoy stereophonic visual space on your existing stereo system.
STEREO SOUND MODE
1
Press the MODE button twice (CD/MP3: once) during playback.
OFF
CD
1
Press the AUDIO button repeatedly during playback to select between STEREO, L-CH or R-CH.
¡
STEREO - both right and left channels are active (stereo)
L-CH - only left channel is active
R-CH - only right channel is active
NOTE
¡
If the Virtual Surround setting is ON, the sound mode will be fixed to STEREO, and can not be changed.
– 42 –
2
Press the ENTER button to set it 1 (Natural effect) or 2 (Emphasized effect) or OFF.
3
Press the MODE or RETURN button to exit.
NOTE (for CD play only)
¡ Virtual Surround will not be effective if the sound mode is set to something other than STEREO.
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 43
THE ON-SCREEN INFORMATION
DVD-V CD MP3
You can check the information about the current disc by pressing the DISPLAY button on the remote control.
For DVD-Vs
1
Press the DISPLAY button during playback to show current Chapter.
¡ The elapsed and remaining playing time of the current chapter will be displayed.
9/49 0:00:00 -0:00:00
For audio CDs
1
Press the DISPLAY button during playback to show the current Track.
¡ The elapsed and remaining playing time of the current track will be displayed.
2
Press the DISPLAY button again to show current Title.
¡
The elapsed and remaining playing time of the current title will be displayed.
2
Press the DISPLAY button again to show current Total Track.
¡ The elapsed and remaining playing time of the current total track will be displayed.
3
Press the DISPLAY button again to exit the display.
3
Press the DISPLAY button again.
¡
The BIT RATE and the current repeat setting will be displayed.
¡
If you are playing a dual layered disc, the layer number will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
For MP3
1
Press the DISPLAY button during playback.
¡
The name of the file currently in play will be displayed.
4
Press the DISPLAY button again to exit the display.
2
Press the DISPLAY button repeatedly to show the track number, the repeat status, and the playback status at the top of the screen.
¡ will be displayed when repeat play has been selected.
T - indicates Track repeat
G - indicates Group (folder) repeat
A - indicates Disc repeat
3
Press the DISPLAY button again to exit the display.
– 43 –
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 44
CHANGING THE DVD SETUP ITEMS
LANGUAGE SETTING
1
Press the SETUP button twice in STOP appears.
¡ If the menu does not appear, press the PLAY button, the STOP button, then the SETUP button twice.
2
4
Press the Arrow buttons ( next items, then press the ENTER button.
AUDIO:
¡
Sets the audio language.
SUBTITLE:
¡
Sets the subtitle language.
DISC MENU:
¡
Sets the language for DVD menu.
5
Press the Arrow buttons (
K / L
) to select the
K / L
) to select a setting, then press the ENTER button.
¡ If OTHER is selected on the AUDIO, SUBTITLE or
DISC MENU screen, press four-digit number to enter the code for the desired language. (Refer to the language code list below.)
¡ Only the languages supported by the disc can be selected.
6
mode so that the DVD SETUP menu
QUICK SETUP
TV MODE
DOLBY DIGITAL
Press the Arrow button B to select CUS-
TOM, then press the ENTER button.
¡ CUSTOM mode will appear.
3
Press the Arrow buttons (s/ B) to select
LANGUAGE, then press the ENTER button to confirm.
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
4:3 LETTER BOX
ON
ORIGINAL
OFF
ENGLISH
Press the SETUP button to exit.
DVD-V
Language options are not available with some discs.
NOTE
¡ Language Setting for Audio and Subtitle is not available with some discs. Then use the AUDIO and the
SUBTITLE buttons. Details are on page 42.
Language
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C-E
Cambodian
Catalan
Chinese [CHI]
Corsican
Croatian
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
F-H
Faroese
Fiji
Finnish [FIN]
French [FRE]
Frisian
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
Code
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
5261
5256
5255
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
Language
L-N
Laothian
Latin
Latvian;Lettish
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
T
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish [TUR]
Turkmen
Twi
U-Z
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian [NOR]
O-R
Occitan
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Scots Gaelic
Code
TO CHANGE THE ON-SCREEN MENUS
You can access the TV/VCR SETUP menu by pressing the SETUP button from the DVD mode. Refer to
“Selecting the Language” on page 16 to changing the on-screen menus.
¡ In case of selecting from the DVD mode, you cannot select “CHANNEL SET UP”, “V-CHIP SET UP”,
“CAPTION”, “TIME SEARCH”, or “INDEX
SEARCH” menus.
– 44 –
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language setting on page 42. If you choose any other languages, ‘---’ will be displayed instead. (3 letter language code is written in bracket.)
EN
01A11
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 45
DISPLAY SETTING
DVD-V
AUDIO SETTINGS
Choose the appropriate Audio settings for your equipment as it only affect during the playback of DVD discs.
You can change certain aspects of the DVD display screens and on-screen messages on the TV screen.
1
Press the SETUP button twice in STOP mode so that the DVD SETUP menu appears.
¡ If the menu does not appear, press the PLAY button, the STOP button, then the SETUP button twice.
1
Press the SETUP button twice in STOP mode so that the DVD SETUP menu appears.
¡ If the menu does not appear, press the PLAY button, the STOP button, then the SETUP button twice.
QUICK SETUP
TV MODE
DOLBY DIGITAL
4:3 LETTER BOX
ON
QUICK SETUP
TV MODE
DOLBY DIGITAL
4:3 LETTER BOX
ON
2
Press the Arrow button B to select CUS-
TOM, then press the ENTER button.
¡ CUSTOM mode will appear.
2
Press the Arrow button B to select CUS-
TOM, then press the ENTER button.
¡
CUSTOM mode will appear.
3
Press the Arrow button (s/ B) to select DIS-
PLAY, then press the ENTER button to confirm.
3
Press the Arrow buttons (s/ B) to select
AUDIO, then press the ENTER button to confirm.
AUDIO
DRC
DOLBY DIGITAL
OFF
ON
DOWN SAMPLING ON
DISPLAY
TV MODE 4:3 LETTER BOX
ANGLE ICON ON
AUTO POWER OFF ON
4
Press the Arrow buttons (
K / L
) to select the below items, then press the ENTER button.
TV MODE:
QUICK
¡ Press the Arrow buttons (K/L) for an item selection, then press the ENTER button.
¡ Select 4:3 LETTER BOX for a black bars appears on top and bottom of the screen.
¡ Select 4:3 PAN & SCAN for a full height picture with both sides trimmed.
¡ The default setting is 4:3 LETTER BOX.
4
Press the Arrow buttons (
K / L
) to select the below items, then press the ENTER buttons.
DRC (Dynamic Range Control):
¡
To compress the range of soft to loud sound.
¡ The default setting is OFF.
DOLBY DIGITAL:
QUICK
Set to On when the unit is connected to a Dolby Digital
Decoder.
(ON: Output a Dolby Digital signal)
(OFF: Convert the Dolby Digital to PCM (2 channel stereo))
¡ The default setting is ON.
ANGLE ICON:
¡ Press the ENTER button repeatedly to turn Angle icon ON or OFF.
¡ The default setting is ON.
AUTO POWER OFF:
¡ Press the ENTER button repeatedly to turn Auto
Power off ON or OFF.
¡ The default setting is ON and it will turn the
TV/DVD/VCR to off automatically after 15 minutes of no use.
DOWN SAMPLING:
¡
Set to ON when outputting in 48 kHz.
¡ The default setting is ON.
When playing disc with copyright Protection
¡ If you select OFF, copyright protection will be activated and sound will be down sampled at 48kHz.
5
Press the SETUP button to exit.
5
Press the SETUP button to exit.
– 45 –
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 46
PARENTAL CONTROL
DVD-V
Parental Control limits the disc viewing that exceed your settings. (with a password or playback will stop.)
This feature allows you to prevent discs with alternative scenes from being played by your children.
PARENTAL LEVEL
Parental Level allows you to set the rating level of your DVD discs. Playback will stop if the disc’s ratings exceed the level you set.
1
Press the SETUP button twice in STOP mode so that the QUICK SETUP menu appears.
¡ If the menu does not appear, press the PLAY button, the STOP button, then the SETUP button twice.
CONTROL LEVELS
¡ALL
All parental lock is cancelled.
¡Level 8
DVD software of any grade (adult/general/children) can be played back.
¡Levels 7 to 2
Only DVD software intended for general use and children can be played back.
¡Level 1
Only DVD software intended for children can be played back, with those intended for adult and general use prohibited.
IF YOU FORGET THE PASSWORD
QUICK SETUP
TV MODE
DOLBY DIGITAL
4:3 LETTER BOX
ON
1
Press the number buttons 4, 7, 3, 7 at step 4.
Then enter your new password.
¡
Password will be cleared and parental level will be set to ALL.
2
Press the Arrow button
B
to select CUS-
TOM, then press the ENTER button.
3
Press the Arrow buttons (
s
/B
) to select
PARENTAL, then press the ENTER button.
2
Proceed the above Steps 5-7 again.
PARENTAL
PARENTAL LEVEL ALL
4
Enter your four-digit password then press the ENTER button.
5
Press the Arrow buttons (
K / L
) to select
PARENTAL LEVEL, then press the ENTER button.
6
Press the Arrow buttons (
K / L
) to select the desired level.
7
Press the SETUP button to exit
NOTES
¡ When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the password.(in the event you forget the password, see below)
¡ To change the password, press the Arrow buttons
(K/L) to select CHANGE at step 5, then press the
ENTER button. Enter the four-digit pass-word, then press the ENTER button.
¡ With some DVDs, it may be difficult to find if they are compatible with parental lock. Be sure to check if the parental lock function operates in the way that you have set.
¡ Record the password in case you forget it.
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 47
TROUBLESHOOTING GUIDE
If the TV/DVD/VCR does not perform properly when operated as instructed in this Owner’s Manual, check the player, consulting the following checklist.
No power.
PROBLEM
The TV/DVD/VCR does not respond to the remote control.
CORRECTIVE ACTION
•
Make sure the power plug is connected to an AC outlet.
•
Make sure the power is turned on.
•
Check if the power plug is connected to an AC outlet.
•
Check the batteries in the remote control.
•
Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles between the sensor and the remote.
•
You have to be within 23 feet of the TV/DVD/VCR.
•
Check if the correct mode is selected. If not switch the mode by pressing the SELECT button on the remote control,whichever you need.
TV/VCR Mode
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked possibilities. Before arranging for service, check these items. It could save your time and money.
PROBLEM
No picture and sound.
No picture or poor picture on
TV/DVD/VCR.
No sound or poor sound.
Bars On Screen
Picture Distorted or Blurred
Picture Rolls Vertically
Lines or Streaks in Picture
No Color
Poor Reception on Some Channels
Ghosts in Picture
Weak Picture
Sound OK, Picture Poor
CORRECTIVE ACTION
•
Make sure the AC cord is connected to an AC outlet.
•
Check antenna connection.
•
Press the SELECT button on the remote control to select TV mode.
Then try other TV feature.
•
Let the TV/DVD/VCR program its tuner memory.
•
Adjust direction or replace antenna.
•
Adjust picture controls.
•
Adjust volume control on remote control or main unit.
•
Press the MUTE button to restore sound.
•
If outside antenna is being used, check for broken wire.
•
Check for local interference.
•
Try a new channel, if OK, then possible station trouble.
•
If outside antenna is being used, check for broken wire.
•
Try a new channel, if OK, then possible station trouble.
•
If outside antenna is being used, check for broken wire.
•
Check for local interference.
•
Try a new channel, if OK, then possible station trouble.
•
Is antenna connected to terminal on the back of the set?
•
If outside antenna is being used, check for broken wire.
•
Adjust COLOR control.
•
Try a new channel, if OK, then possible station trouble.
•
Is antenna connected to terminal on the back of the set?
•
If outside antenna is being used, check for broken wire.
•
Check for local interference.
•
Try a new channel, if OK, then possible station trouble.
•
Is antenna connected to terminal on the back of the set?
•
If outside antenna is being used, check for broken wire.
•
Adjust CONTRAST & BRIGHT control.
•
Try a new channel, if OK, then possible station trouble.
•
Is antenna connected to terminal on the back of the set?
•
If outside antenna is being used, check for broken wire.
•
Check for local interference.
•
Adjust CONTRAST & BRIGHT control.
– 47 –
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 48
PROBLEM
Picture OK, Sound Poor
Timer recording is not possible.
Cannot go into Record mode.
Playback picture is partially noisy.
No picture but the audio is OK in playback.
No operation by infrared Remote
Control.
Video or color fades in and out when making a copy of a video tape.
Different color marks on screen.
CORRECTIVE ACTION
•
Try a new channel, if OK, then possible station trouble.
•
Check for local interference.
•
Make sure the timer recording is set correctly.
•
Make sure the power is off.
•
Make sure the TV/DVD/VCR clock is set correctly.
•
Make sure the tape has an erase-prevention tab. If need, cover the
• hole with plastic tape.
•
Adjust tracking control for a better picture using the CHANNEL
• button
K or L on the TV/DVD/VCR.
•
Head cleaning may be necessary. Refer to “AUTO HEAD
•
CLEANING” on page 50.
•
Make sure the AC cord is connected to an AC outlet.
•
Check batteries in remote control.
•
You can not copy a copyrighted video tape. You are experiencing
• copy guard protection.
•
Magnetism from nearby appliances and geomagnetism might affect the color of the TV picture. Move the TV/DVD/VCR away from the appliances, the TV/DVD/VCR can repair itself automatically. If you want to repair immediately, turn off using the POWER button, then turn it on again 30 minutes or so later (27” model), or unplug the power cord, then plug it in again 30 minutes or so later (19” model).
CLOSED CAPTION PROBLEM
My TV/DVD/VCR is showing captions that are misspelled.
POSSIBLE REMEDY
• You are watching a live broadcast and spelling errors made by the
• closed captioning production company may pass through uncorrected.
• A prerecorded program will not show any misspelled words because
• of the normal time available for editing the captions.
My TV/DVD/VCR will not show • Captions that are delayed a few seconds behind the actual the text dialogue are common for live broadcast. Most captioning production in its entirety or there is a delay of • companies can display a dialogue to a maximum of 220 words what is being said.
• per minute. If a dialogue exceeds that rate, selective editing is used
• to insure that the captions remain up-to-date with the current
• TV screen dialogue.
My captions are scrambled with white boxes on the TV screen.
• Interference caused by building, power lines, thunderstorms, etc.
• may cause scrambled or incomplete captions to appear.
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed as being closed captioned but none • up the actual program so that additional advertising time can be of the captions were displayed.
• given. Since the decoder cannot read the compressed information,
• captions will be lost.
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating show any captions. The tape box • company accidentally left out the captioning signals during the mentions it being closed captioned.
• copying process.
My TV screen shows a black box • You are in the TEXT mode. Select CAPTION mode to CAPTION on certain channels.
• [OFF].
– 48 –
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 49
DVD Mode
No picture.
PROBLEM
Disc cannot be played.
CORRECTIVE ACTION
• Connect the video cables firmly.
• Insert a correct video disc that plays on this TV/DVD/VCR.
• Press the SELECT button on the remote control to select DVD mode.
Then, try other DVD feature.
• Insert the disc.
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
No sound.
No DTS audio is output.
Distorted picture.
• Connect the audio cables firmly.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• This TV/DVD/VCR does not support DTS audio. This is not a malfunction.
• There are some cases where pictures may be slightly distorted, which are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
• The selected language is not available for audio or subtitles on the DVD.
Audio or subtitle language does not match the set up This is not a malfunction
The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera angles. This is not a malfunction
Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected changed language. This is not a malfunction.
“Prohibited icon” appears on the screen, prohibiting an operation
• That operation is prohibited by the player or the disc.
This is not a malfunction.
CD sound dropout
No CD reproduction
• Scratched disc. Replace the disc with unscratched one.
DVD picture dropout
DVD picture freeze
DVD picture in mosaic
No DVD reproduction
NOTES:
•
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s Manual for details on correct operations.
•
Playback from a desired track and random playback are not available during program playback.
– 49 –
EN
01A11
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 50
MAINTENANCE
CABINET CLEANING
•
Wipe the front panel and other exterior surfaces of the TV/DVD/VCR with a soft cloth immersed in lukewarm water and wrung dry.
•
Never use a solvent or alcohol. Do not spray insecticide liquid near the TV/DVD/VCR. Such chemicals may cause damage and discoloration to the exposed surfaces.
1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please call our help line at 1-800-968-3429, to locate an Authorized Service Center.
NOTES:
•
Remember to read the instructions included with the video head cleaner before use.
•
Clean video heads only when problems occur.
AUTO HEAD CLEANING
•
Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.
•
Playback picture may become blurred of interrupted while the TV program reception is clear. Dirt accumulated on the video heads after long periods of use, or the usage of rental or worn tapes can cause this problem.
If a streaky or snowy picture appears during playback, the video heads in your TV/DVD/VCR may need to be cleaned.
SERVICING
•
Should your TV/DVD/VCR become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power cord, and please call our help line at 1-800-968-3429, to locate an Authorized
Service Center.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
•
If the player still does not perform properly when it is operated while referring to the relevant sections and to
"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
•
Use discs which have the following logos on them.
(Optical audio digital discs.)
•
•
To clean-off, use a soft cloth.
Do not use a hard cloth since this will mar the disc.
•
Wipe the disc in a straight line from center to edge.
•
Never wipe with a circular motion.
•
Do not use detergent or abrasive cleaning agents.
•
Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.
•
Always store the disc in its protective case when it is not used.
– 50 –
TD900UA(P36-52).QX33 03.7.31 1:22 PM Page 51
SPECIFICATIONS
GENERAL SPECIFICATIONS
TV/VCR
CRT
[20 inch model]: 20 inch in-line gun, 90˚ deflection tube
Television system : NTSC-M
Closed caption system :§15.119/FCC
Video Heads :
Tape width :
Tape speed
SP :
Rotary four-head
1/2 inch
LP :
SLP :
Tuner channel
TV VHF Low :
33.40mm/sec.
16.67mm/sec.
11.12mm/sec.
#2~#6
TV VHF High : #7~#13
TV UHF : #14~#69
CATV
VHF :
MID band :
SUPER band :
HYPER band :
5A
A5~A1, A~I
J~W
W+1~W+84
ELECTRICAL SPECIFICATIONS
Sound output: 2 speakers, 1W, 8 ohm
OTHER SPECIFICATIONS
Terminals
Antenna input:
Headphone:
Coaxial digital
VHF/UHF/CATV
75 ohm unbalanced (F-type)
Video input: RCA connector
[
1
Audio L/R input: RCA connector
[
2
1/8” stereo (3.5 mm) audio output: One pin jack,
500m Vpp (75 ohm)
Analog audio L/R output :
Remote control:
RCA connector
[
2
Digital encoded infrared light system
Operating temperature: 5ºC to 40ºC
(41ºF~104ºF)
Power requirements: AC 120V, 60Hz
Power consumption
(Maximum):
Picture tube:
Dimensions:
Weight:
100W
20"
H :20-3/16” (512.5mm)
W:22-1/8” (562mm)
D :20-3/16” (513mm)
59.5 lbs (27kg)
DVD
Product type: DVD Player
Discs: DVD video, Audio CD
Output signal format: NTSC color
Frequency response
(out put jack)
DVD (linear sound): 20 Hz to 22 kHz
(sample rate: 48 kHz)
20 Hz to 44 kHz
(sample rate: 96 kHz)
20 Hz to 20 kHz CD:
Signal-to-noise ratio
(S/N ratio)(out put jack)
CD: 80 dB (EIAJ)
Dynamic range
(out put jack)
DVD (linear sound): 85 dB
CD: 84 dB (EIAJ)
Total distortion factor
CD:
Wow and flutter:
0.07% (EIAJ)
Below the measurement limitation (+/-0.001%
W PEAK) (EIAJ)
•
Designs and specifications are subject to change without notice.
•
If there is a discrepancy between languages, the default language will be English.
– 51 –
EN
01A11
TD900UA-ES.QX33 03.7.31 1:21 PM Page 52
INDICE
■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 52
PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 52
MANDO A DISTANCIA . . . . . . . . . . . . . . . . . . . . . . . . . 52
VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 53
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 53
CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 53
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 54
MODO DE ENTRADA EXTERNA . . . . . . . . . . . . . . . . 54
CONEXIÓN A UN SISTEMA ESTÉREO . . . . . . . . . . . . 54
CONEXIÓN A UN AMPLIFICADOR ESTÉREO
EQUIPADO CON TOMAS DE ENTRADA DIGITAL,
PLATINA MD O PLATINA DAT (Para DVD). . . . . . . . . 54
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SECCIÓN DE TV/VCR
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 54
PREAJUSTE DE CANALES. . . . . . . . . . . . . . . . . . . . . . 55
CÓMO BORRAR (AGREGAR) CANALES . . . . . . . . . . 55
SECCIÓN DE DVD
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55
CONTROLES DE
OPERACIÓN Y FUNCIONES
PANEL FRONTAL DEL
TELEVISOR/DVD
Consulte la figura 1 de la página 9
MANDO A DISTANCIA
Consulte la figura 2 de la página 9
VISTA POSTERIOR
Consulte la figura 3 de la página 10
1.
Botón POWER
Presione este botón para conectar y desconectar la alimentación.
2.
Botones VOLUME X/Y
Presione estos botones para controlar el nivel de volumen del DVD y el televisor.
3.
Botones SKIP (para DVD)
Presione el botón correspondiente una vez para omitir capítulos o pistas y desplazarse a un punto específico.
Mantenga el botón presionado para cambiar la velocidad de reproducción en avance o retroceso.
4.
Botón PLAY
Inicia la reproducción del contenido del disco o cinta.
5.
Botón de parada STOP
Panel frontal:
Presione para detener el movimiento del disco.
Mando a distancia:
●
Modo DVD
Presione para detener el movimiento del disco.
●
Modo TV/VCR
Presione para detener el movimiento de la cinta.
6.
Botón OPEN/CLOSE
Presione este botón para insertar discos en la bandeja o retirarlos de ella.
7.
Bandeja de carga del disco
8.
Indicador DVD
Se ilumina durante el modo DVD.
9.
Botón SELECT
Presione este botón para cambiar al modo TV/VCR, modo de entrada externa o modo de DVD.
– 52 –
10.
Indicador TV/VCR
Se ilumina durante el modo TV/VCR.
11.
Botones CHANNEL K/L
Utilice estos botones para seleccionar canales memorizados.
12.
Indicador de grabación
Parpadea durante la grabación. Se ilumina durante el modo de espera de grabación controlada por temporizador.
13.
Botón REC/OTR (RECORD)
Presione este botón para grabar manualmente. Este botón también activa la función de grabación instantánea (OTR). (La función OTR sólo está disponible durante el modo TV/VCR.)
14.
Botón REW (para TV/VCR)
Presione este botón para rebobinar la cinta o para ver la imagen rápidamente en dirección de retroceso durante el modo de reproducción. (Búsqueda en dirección de retroceso)
15.
Botón FWD (para TV/VCR)
Presione este botón para adelantar rápidamente la cinta o para ver la imagen rápidamente en dirección de avance durante el modo de reproducción. (Búsqueda en dirección de avance)
16.
Botón STOP/EJECT
Presione este botón para detener la cinta. Presiónelo en el modo de parada para retirar la cinta del televisor/DVD/videograbadora.
17.
Ventanilla del sensor de mando a distancia
18.
Toma HEADPHONE
Para conectar auriculares (no suministrados) y escuchar en privado.
19.
Toma de entrada VIDEO
Conecte aquí la toma de salida de vídeo de una videocámara o de una videograbadora.
20.
Tomas de entrada AUDIO L/R
Conecte aquí las tomas de salida de audio de una videocámara o de una videograbadora.
21.
Compartimiento del cassette
22.
Botón PICTURE
Presione este botón para ajustar la imagen.
23.
Botones numéricos
Modo TV:
Presione dos botones para acceder directamente al canal deseado.
No olvide presionar “0” antes de elegir un canal de un solo dígito.
Botón +100
Presione este botón para seleccionar canales de televisión por cable cuyo número sea igual o superior a 100.
Modo DVD:
Presione este botón para introducir el número deseado.
Botón +10
Presione este botón para introducir números iguales o mayores que 10.
24.
Botón PAUSE
Hace una pausa en la reproducción del disco o cinta.
25.
Botón SPEED
Presione este botón para seleccionar la velocidad de grabación deseada: SP/SLP.
26.
Botón C.RESET
Presione este botón para poner el contador en 0:00:00.
Presiónelo también para cancelar un ajuste de programa de temporizador.
27.
Botón DISPLAY
Modo TV/VCR:
Para visualizar el contador o el número del canal y la fecha actual en la pantalla del televisor.
Modo DVD:
Indica el estado actual en la pantalla del televisor para fines de comprobación.
ES
0C28
TD900UA-ES.QX33 03.7.31 1:21 PM Page 53
28.
Botón SETUP
Presione este botón para activar o salir del modo de menús de televisor o configuración de DVD.
29.
Botón TITLE
Para visualizar el menú de títulos.
30.
Botón CLEAR
Para cancelar ajustes.
31.
Botón MODE
Activa el modo de reproducción programada o el modo de reproducción aleatoria.
32.
Botón SEARCH MODE
Presione este botón para localizar un punto deseado.
33.
Botón AUDIO
Presione este botón para seleccionar un idioma de audio o el modo de sonido deseado.
34.
Botón SUBTITLE
Presione este botón para seleccionar el idioma de subtítulos deseado.
35.
Botón REPEAT
Repite la reproducción del disco, título, capítulo o pista actual.
36.
Botón ANGLE (modo DVD)
Presione este botón para cambiar el ángulo de la cámara y ver la secuencia que se está reproduciendo desde un
ángulo diferente.
37.
Botón A-B REPEAT
Repite la reproducción de una sección seleccionada.
38.
Botón RETURN
Permite volver a la operación anterior en el modo de configuración de DVD.
39.
Botón ENTER
Presione este botón para establecer un ajuste.
40.
Botones de flechas
Modo TV/VCR:
Presione estos botones para seleccionar un modo de ajuste en el menú que aparece en la pantalla del televisor.
Presiónelos también para seleccionar opciones o establecer ajustes en un menú en particular.
Modo DVD:
Use estos botones para hacer ajustes mientras observa la imagen en la pantalla del televisor.
41.
Botón DISC MENU
Muestra los menús contenidos en el DVD.
42.
Botón ZOOM
Amplía parte de la imagen reproducida de un DVD.
43.
Botón MUTE
Suprime la salida de sonido. Presiónelo de nuevo para restablecer el sonido.
44.
Botón SLEEP
Utilice este botón para ajustar el temporizador de dormir.
45.
Botón SELECT
Presione este botón para cambiar entre los modos
TV/VCR y DVD. El modo seleccionado (TV/VCR o
DVD) se visualiza en el indicador del panel delantero.
46.
Toma de entrada ANT.
Conéctela a una antena, sistema de televisión por cable o sistema de satélite.
47.
Cable de alimentación
Conéctelo a una toma de CA estándar (120 V, /60 Hz).
NOTA: Antes de conectar el cable de alimentación a una toma de CA estándar, retírelo del gancho para evitar dañarlo.
48.
Toma de salida de audio digital COAXIAL
Conéctela solamente a la entrada digital de un amplificador externo o decodificador de audio de DVD.
49.
Toma de salida AUDIO L/R
Conéctela a la entrada de audio analógico de un amplificador o decodificador externo.
PREPARACIÓN PARA LA
UTILIZACIÓN
CONEXIONES DE ANTENA/CABLE
Consulte la figura 4 de la página 11
ANTENAS SEPARADAS DE VHF/UHF
En algunas zonas será necesario utilizar una antena exterior.
TELEVISIÓN POR CABLE SIN CAJA DE
CONVERTIDOR/DECODIFICADOR
Utilice esta conexión si su sistema de televisión por cable se conecta directamente a su televisor/DVD/ videograbadora, sin una caja de convertidor.
Con esta conexión podrá:
1) Utilizar el mando a distancia del televisor/DVD/ videograbadora para seleccionar canales.
2) Programar uno o más canales decodificados para grabación automática controlada por temporizador.
NOTA: Este televisor/DVD/videograbadora SÓLO puede grabar el canal que se está viendo.
TELEVISIÓN POR CABLE CON CAJA
DE CONVERTIDOR/DECODIFICADOR
O CAJA DE SATÉLITE
Si su compañía de televisión por cable le suministra una caja de convertidor o si utiliza un sistema de satélite, podrá utilizar la conexión básica que se muestra en la ilustración.
Al utilizar esta conexión, también podrá grabar canales codificados. Sin embargo, la selección de los canales deberá hacerse con la caja de convertidor o con la caja de satélite. Esto significa que no es posible cambiar de canal utilizando el mando a distancia del televisor/DVD/ videograbadora. La grabación en ausencia (controlada por temporizador) está limitada a un canal a la vez.
PARA GRABAR UN CANAL
CODIFICADO/DECODIFICADO
1. Ajuste el selector de canales del televisor/DVD/videograbadora al canal de salida de la caja de convertidor de televisión por cable o caja de satélite. (Ej., CH3)
2. Seleccione el canal que desea grabar en la caja de convertidor de televisión por cable o caja de satélite.
Nota para el instalador de sistemas CATV
Esta nota tiene la finalidad de llamar la atención del instalador de sistemas CATV para que tenga en cuenta el Artículo 820-40 de la NEC, que proporciona recomendaciones para hacer una conexión a tierra apropiada y, en particular, especifica que la tierra del cable debe conectarse al sistema de puesta a tierra del edificio, tan cerca del punto de entrada del cable como sea posible.
CONEXIÓN A TOMAS DE
ENTRADA EXTERNA
Cuando vea un programa grabado en otra fuente (videograbadora o videocámara), utilice las tomas de entrada de audio/vídeo de la parte delantera del televisor/DVD/videograbadora.
Conecte las tomas de salida de audio/vídeo de otra fuente a las tomas AUDIO L/R y VIDEO de este televisor/DVD/videograbadora. Luego, presione los botones
CHANNEL K/L hasta que aparezca "AUX" en la pantalla.
– 53 –
ES
0C28
TD900UA-ES.QX33 03.7.31 1:21 PM Page 54
NOTA:
• Cuando conecte una videograbadora monofónica (otra fuente) a este televisor/DVD/videograbadora, conecte la toma de salida de audio de la videograbadora monofónica
(otra fuente) a la toma AUDIO L de este televisor/DVD/videograbadora. El audio saldrá igualmente por los canales izquierdo y derecho.
Consulte la figura 5 de la página 12
•
Consulte los manuales de instrucciones de los componentes que va a conectar al televisor/DVD/videograbadora.
•
Ajuste la función Dolby Digital a OFF para salida de audio en el modo de configuración. La reproducción en un televisor/DVD/videograbadora utilizando ajustes incorrectos puede generar ruido y distorsión, y también puede causar daños a los altavoces.
PARA INSERTAR LAS PILAS
1) Abra la cubierta del compartimiento de las pilas empujando la cubierta del mando a distancia en el sentido de la flecha.
2) Inserte 2 pilas "AA" en el compartimiento de las pilas, en el sentido indicado por las marcas de polaridad (+/-).
3) Vuelva a poner la cubierta.
MODO DE ENTRADA EXTERNA
CONEXIÓN A UN DECODIFICADOR
DOLBY DIGITAL (para DVD)
Si utiliza este televisor/DVD/videograbadora para reproducir un disco DVD grabado en formato de sonido envolvente Dolby Digital de 5,1 canales, el televisor/DVD/videograbadora emitirá un flujo de datos
DOLBY DIGITAL desde su toma de salida de audio digital COAXIAL. Si conecta el reproductor a un decodificador Dolby Digital, podrá disfrutar de una tonalidad más convincente y real, con un sonido envolvente potente y de alta calidad similar al de los cines.
Utilice cables digitales coaxiales de audio disponibles en el comercio especializado para hacer las conexiones de audio.
Al usar una señal de entrada externa (otra videograbadora o una videocámara), conecte los cables de salida de audio/vídeo del equipo externo a las tomas AUDIO L/R
IN/ VIDEO IN de su televisor/DVD/videograbadora.
Luego, presione los botones CHANNEL K/L hasta que aparezca "AUX" en la pantalla.
CONEXIÓN A UN SISTEMA
ESTÉREO
NOTAS:
•
Asegúrese de desconectar la alimentación de todos los componentes del sistema antes de conectar otro componente.
•
Consulte el manual de instrucciones de su sistema estéreo y de cualquier otro componente que vaya a conectar al televisor/DVD/videograbadora.
Consulte la figura 6 de la página 13
Consulte la figura 8 de la página 14
NOTAS:
•
Asegúrese de desconectar la alimentación de todos los componentes del sistema antes de conectar otro componente.
•
Consulte los manuales de instrucciones de los componentes que va a conectar al televisor/DVD/videograbadora.
•
Si conecta un decodificador Dolby Digital, ajuste la función DOLBY DIGITAL a ON para salida de audio en el modo de configuración.
•
A menos que se haga la conexión a un decodificador Dolby Digital, ajuste la función Dolby
Digital a OFF para salida de audio en el modo de configuración. La reproducción en un televisor/DVD/videograbadora utilizando ajustes incorrectos puede generar ruido y distorsión, y también puede causar daños a los altavoces.
CONEXIÓN A UN AMPLIFICADOR
ESTÉREO EQUIPADO CON TOMAS
DE ENTRADA DIGITAL, PLATINA
MD O PLATINA DAT (Para DVD)
Fabricado bajo licencia de Dolby
Laboratories. “Dolby” y el símbolo de la D doble son marcas de fábrica de Dolby
Laboratories.
Utilice un cable digital coaxial de audio de venta en el comercio especializado para hacer las conexiones de audio.
Conexión a un amplificador equipado con tomas de entrada digital, platina MD o platina DAT.
SECCIÓN DE TV/VCR
PREPARACIÓN PARA LA
UTILIZACIÓN
Consulte la figura 7 de la página 13
NOTAS:
•
La fuente de audio de un disco grabado en formato de sonido envolvente Dolby Digital de 5,1 canales no se puede grabar como sonido digital mediante una platina MD o DAT.
•
Asegúrese de desconectar la alimentación de todos los componentes del sistema antes de conectar otro componente.
Puede programar el sintonizador para explorar todos los canales que pueda recibir en su zona.
NOTA: La programación de la memoria de canales
NO es necesaria cuando se hace la conexión a una caja de televisión por cable o a una caja de satélite.
Simplemente ajuste el selector de canales del televisor/DVD/videograbadora a la posición correspondiente al canal de salida de la caja de televisión por cable o caja de satélite (ej., CH3). Luego, seleccione el canal que desea ver en la caja de televisión por cable o en la caja de satélite.
– 54 –
ES
0C28
TD900UA-ES.QX33 03.7.31 1:21 PM Page 55
PREAJUSTE DE CANALES
TV/VCR
1
Conecte el cable de alimentación del televisor/DVD/videograbadora
Conecte el cable de alimentación del televisor/DVD/videograbadora
NOTA:
•
Si aparecen algunos dígitos en la esquina de la pantalla, presione el botón POWER sin desconectar el cable de alimentación.
2
Encienda el televisor/DVD/videograbadora
Presione el botón POWER para encender el televisor/DVD/videograbadora.
3
Seleccione “ENGLISH”, “ESPAÑOL” o
“FRANÇAIS”
Presione el botón ENTER para seleccionar "ENG-
LISH" = inglés, "ESPAÑOL" o "FRANÇAIS" = francés. "[ ]" indica el idioma seleccionado.
4
Inicie el preajuste automático
Presione el botón de flecha K o L para señalar
"AUTOPRESELECCION".
Luego, presione el botón ENTER.
El sintonizador explora y memoriza todos los canales activos de su zona.
NOTAS:
•
El televisor/DVD/videograbadora distingue entre los canales de TV estándar y los canales de televisión por cable.
•
Si desea reproducir o grabar una cinta de vídeo
ANTES de preajustar el sintonizador, deberá presionar el botón SETUP del mando a distancia.
•
El televisor/DVD/videograbadora puede memorizar canales de TV como canales de CATV si las condiciones de recepción no son buenas. Si esto sucede, vuelva a intentar la acción AUTO MEMO cuando las condiciones de recepción mejoren.
5
Una vez finalizada la exploración
El sintonizador se detiene en el canal memorizado más bajo. Si desea recuperar los canales seleccionados, podrá seleccionar los canales directamente con los botones numéricos o los botones CHANNEL K o
L del mando a distancia.
CÓMO BORRAR (AGREGAR)
CANALES
TV/VCR
Puede borrar de la memoria los canales que ya no recibe o que ve muy raramente. (Por supuesto, puede volver a agregar a la memoria los canales que haya borrado de la misma.)
1
Seleccione “AJUSTE DE CANAL”
Presione el botón SETUP del mando a distancia.
Presione el botón de flecha K o L para señalar
“AJUSTE DE CANAL”.
Luego, presione el botón ENTER.
2
Seleccione “AGREGAR/BORRAR”
Presione el botón de flecha K o L para señalar
“AGREGAR/BORRAR”.
Presione el botón ENTER.
3
Introduzca el número del canal deseado
Presione el botón de flecha K o L hasta que aparezca el número del canal deseado. (También puede utilizar también los botones numéricos o los botones
CHANNEL K/L para introducirlo.) (Ejemplo: CH8)
4
Borre el canal de la memoria o agréguelo a ella
Presione el botón ENTER. El número del canal seleccionado se ilumina de color rojo. El canal de borra de la memoria.
Canal agregado: Se enciende en azul.
Canal borrado: Se enciende en rojo.
•
Para borrar otro canal, repita los pasos [3] y [4].
•
Si vuelve a presionar el botón ENTER, el canal se memorizará de nuevo.
•
Presione el botón RETURN para hacer que el televisor/videograbadora vuelva al menú SETUP.
5
Salga del modo de preajuste de canales
Presione el botón SETUP del mando a distancia para volver al modo de televisor.
NOTA: Para confirmar que los canales han sido borrados o agregados, presione el botón CHANNEL K o
L
.
SECCIÓN DE DVD
REPRODUCCIÓN BÁSICA
DVD-V CD
Para empezar
¡
Conecte la alimentación del amplificador y otros componentes, si es necesario.
1
Presione el botón POWER.
¡
La alimentación se conectará.
2
Presione el botón OPEN/CLOSE para abrir la bandeja de carga del disco.
3
Ponga el disco deseado en la bandeja, con la etiqueta hacia arriba.
4
Presione el botón PLAY.
¡ La bandeja se cerrará automáticamente y la reproducción comenzará desde el primer capítulo o pista del disco. Si la reproducción no comienza automáticamente, presione el botón PLAY.
¡ Cuando reproduzca un DVD que tenga grabado un menú de títulos, el menú podrá aparecer en la pantalla.
5
Presione el botón STOP para detener la reproducción.
– 55 –
ES
0C28
TD900UA(P36-52).QX33 03.9.1 11:08 AM Page 52
LIMITED WARRANTY
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE
PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE
UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure, please call 1-800-968-3429 or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-968-3429 http://www.funai-corp.com
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in Malaysia 0EMN02252
TD900UA ★★★★
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 52 PANEL FRONTAL DEL TELEVISOR/DVD
- 52 MANDO A DISTANCIA
- 52 VISTA POSTERIOR
- 53 CONEXIONES DE ANTENA/CABLE
- 53 CONEXIÓN A TOMAS DE ENTRADA EXTERNA
- 54 PARA INSERTAR LAS PILAS
- 54 MODO DE ENTRADA EXTERNA
- 54 CONEXIÓN A UN SISTEMA ESTÉREO
- 54 PLATINA MD O PLATINA DAT (Para DVD)
- 54 (para DVD)
- 54 ■ PREPARACIÓN PARA LA UTILIZACIÓN
- 55 PREAJUSTE DE CANALES
- 55 CÓMO BORRAR (AGREGAR) CANALES
- 55 REPRODUCCIÓN BÁSICA