advertisement
▼
Scroll to page 2
of 16
INSTALLATION GUIDE 2500 2500M Advanced Remote Vehicle Starter & Alarm WWW.ULTRASTARTERS.COM TECH SUPPORT Western Canada 1 800 279-0636 United States: 1 866 698-5872 Eastern Canada. Bilingual Support: 1 800 268-0683 E-Mail Tech Support: [email protected] Check Our Web Site: www.ultrastarters.com Installation Guide TABLE OF CONTENTS 2500 Wiring Diagram Pre-Installation Components Recommended Pre-Installation Procedures Recommended Install procedures Wire Connectors 6 Pin Connector 14 Pin Connector 3 Pin Red Connector 4 Pin Blue Connector Jumper Selections Installation Basic Installation - Quick start Plugging In The Module Auto Tach Learn Shock Sensor Programming Programming Program Overview & System Reset Program Menu 1 (User Settings) Program Menu 2 (Alarm Settings) Program Menu 3 (Starter Settings) Program Menu 4 (Tach Settings) Other Features And Operations Reservation Mode Transmitter Programming Battery Replacement Service mode Remote Service Mode Warranty System Operation Relay Diagrams Page 3 Page 4 Page 5 Page 6-7 Page 7-11 Page 12 Page 14-15 Page 16 DIAGNOSTICS PARK LIGHTS STATUS LED DIAGNOSTIC CODE 3 Flashes Series of 3 Flashes Door Opened “M” Models 4 Slow Flashes Series of 4 Flashes Not in Reservation Mode “M” units 5 Flashes Series of 5 Flashes Hood Pin Grounded (Open) 6 Flashes Series of 6 Flashes Brake Pedal Shutdown 7 Flashes Series of 7 Flashes Tach Lock-Out 8 Flashes Series of 8 Flashes 3 Start Attempts with no start If the remote starter has a failed start attempt or if a safety input is activated the Diagnostic Memory will store up to four shutdowns in memory. This information can then be accessed to determine the source of the shutdown. To Enter Diagnostic Mode: Step 1 - Turn the ignition on wait two seconds then turn off. Press the Program Button and release. Step 2 - The system will respond with three park light flashes and the siren will chirp the same number of times as the events in memory. ( Maximum four events, four chirps) NOTE: If the siren does not chirp, there are no events in memory. Step 3 - Press the Program Button once to view the last shut down code. The siren will chirp once to confirm code one. (If the siren does not chirp, there are no codes in memory). Step 4 - The LED’s on the antenna will flash a code corresponding to a shut down trigger. Press the Program Button again to check the second code. The siren will chirp twice to confirm code two. Step 5 - To Clear Diagnostic Memory. While in Diagnostic Mode press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp once. 2 NOTE: Once diagnostic memory has 4 improper shutdown events in memory, the system will not record any further shutdown events until the system memory has been cleared. Installation Guide WIRING DIAGRAM Starter Yellow (+) 30amp Output Heater Green (+) 30amp Input Main Power Red (+) 30amp Input Main Power Red (+) 30amp Output Selectable P.5 White (+) 30amp Output Ignition 1 Blue (-)500ma Output RE-ARM YELLOW (-)500ma Output STARTER DISABLE ORANGE (-)500ma Output FACTORY DISARM BROWN (-)500ma Output TRUNK RELEASE RED/WHITE (-)500ma Output THIRD IGNITION (-) WHITE / VIOLET (-) DOOR TRIGGER GREEN HOOD PIN GREEN/WHITE Negative Input Negative Input INPUT 2 4 Positive Input (+) DOOR TRIGGER PURPLE Positive Input BRAKE PEDAL PINK GROUND BLACK TACH INPUT BLUE/WHT Negative Input (A/C) Input (-) Input Positive 15amp Negative Input 3 5 1 2 3 4 5 6 7 8 9 GLOW PLUG BLUE PARK LIGHTS WHITE PARK BRAKE 6 1 Jumper Access (+) 30amp Output BLACK/WHITE (-)500ma Output 4th Ch. Programmable White / Green (-)500ma Output Dome Light Supervision Black BLK/WHT Positive 3 amp Siren Output White / Blue Negative Input Trunk Pin Switch Input Red BLK/WHT 10 11 12 13 14 10 11 12 13 STARTER DISABLE. SEE PAGE. 7 TEMPERATURE SENSOR INPUT (OPTIONAL) RF ANTENNA WITH DUAL LED’s & BUILT-IN VALET SWITCH 4 PIN BLUE *Must be connected to operate the system SIDE VIEW (-)500ma Output Door Lock Green (-)500ma Output 12V+ for Relays Red (-)500ma Output Door Unlock Blue (-)500ma Output Passenger Door Unlock Pink (-)Input Sensor Full-Warn Blue (-) Input Sensor Pre-Warn Green (-)500ma Output Sensor Ground Black (+)500ma Output Sensor 12V+ Power Red SATELLITE LINK PLUG (-)500ma Output Negative When Disarmed Green (-)500ma Output Horn Honk/ 5th Channel Pink (+) Input (+)Disconnect / Start trigger Blue 4 PIN RED 4 PIN WHITE 4 PIN WHITE ***500ma outputs are low current and are designed to activate relays 4 PIN WHITE 3 Installation Guide INSTALLATION TIPS Components - Control module - Remote transmitter(s) - Antenna with built in Program Button and LED’s - 6 pin main harness with dual 30amp power inputs - 14 pin harness - 4 pin square harness. - 4 pin keyless entry harness - 4 pin Aux. sensor harness - Multi-tone Siren - Hood pin safety switch - Installation guide - Owners manual Recommended Pre-Installation Procedures BEFORE STARTING INSTALLATION: - Discuss the optional features with the customer. - Take a few minutes to review the installation and owners manuals. - Check if the vehicle has a factory security or anti-thieft system. *If equipped, inform the customer of addition parts and labour. - Do a walk around the vehicle and check for any damage. - If installing a LED discuss the placement with customer before installing. Note: This remote starter is designed for fuel injected and diesel engines. Recommended Installation Procedures Proper Connections - Remote Starters can handle loads of up to 30 amps for extended periods of time. It is CRITICAL to insure that ALL high current connections are properly soldered and insulated with quality electrical tape. Failing to insure proper connections will result in warranty being VOID and can result in a FIRE. The manufacturer is not responsible for any such damages. It only takes a few more minutes to do the job RIGHT. Under Hood Connections - Route the hood pin and tach wires through the firewall into the engine compartment. Always try to pull the wires through a factory rubber grommet. If drilling through the firewall, BE CAREFUL. Check for obstructions on both sides of the firewall. After drilling use a snap in grommet to protect the wires from sharp edges. Installing the External Long Range Antenna - To insure the best possible reception, place the antenna in the center of the windshield, behind the rear view mirror. Before attaching to the glass ensure that the surface is clean and dry. For best results with range, place the antenna below the tint screen. Run the cable under the head liner and behind the A-pillar panel. Be careful not to pinch the antenna cable. Plug the antenna into the BLUE connector on the Control Module. NOTE: This step is not used on Alarm Only Units with no External Antenna. Mounting The Control Module - Never mount the module in the engine compartment. Select a location under the dash to install the main module. Be certain that the module is securely attached and does not obstruct any serviceable areas. Do not force or jam the module into tight places instead of mounting. The module must be free from all moving parts such as brake, clutch and gas pedal linkages. Do not place the module directly in front of a heater vent. Testing The System - When the installation is complete, it will be necessary to test that the system is working correctly. The system’s default programming will work on the majority of vehicles, but might need to be adjusted for some applications. If the installation requires special timing or additional features, proceed to Program Mode. ATTENTION: Hood Pin MUST always be connected!! 4 NOTE: Always inform user to place system in Service Mode before any service work is performed on the vehicle. Installation Guide WIRING CONNECTORS 6 Pin Power Connector Yellow Green Red Red Blue White Starter Heater 12 power 12 power Ignition 1 Selectable 30amp output 30amp output 30amp input 30amp input 30amp output 30amp output 12volts during crank only. 12volts in accessory. Off during start. Constant 12volt power at ignition harness. Constant 12volt power at ignition harness. 12volts in ignition and start positions. Jumper Selectable. See Page 5. 14 Pin Connector Yellow Orange Brown Red/White White/Violet Green Purple Green/White Pink Black Blue/White Blue White Black/White Re-Arm (-) Output Disarm 3rd CH (-)Running (-) Door (+) Door Hood Pin Brake Ground Tach Glow Plug Park Lights Park Brake 0.75sec Pulse With Lock And On Shutdown. Negative While Locked - **Starter Program Mode. 0.75sec Pulse With Unlock And Before Start. Trunk Release - Active When The Unlock Button Is Held For 3seconds. Negative Output While Running. Negative Door Trigger Input - Manual Trans And Alarm Units Only. Positive Door Trigger Input - Manual Trans And Alarm Units Only. Negative Hood Pin Input - MUST BE CONNECTED!! Positive Brake Input - MUST BE CONNECTED!! System Ground Input - MUST BE CONNECTED!! Tach Signal Input - MUST BE CONNECTED!! Negative Glow Plug Input - DIESEL ENGINE ONLY. **Starter Program Mode. Positive Park light Output - 10 Amp Max. Negative Park Brake Input - Manual Transmission Models Only. 4 Pin Connector Square White/Green Black White/Blue Red Channel 4 Dome Light Siren Trunk Pin Programmable- See Alarm Settings. Menu 2. Negative Output For Dome Light Supervision. Positive Output For Siren. Negative Input for Trunk Pin. 4 Pin Connector Red Green Red Blue Pink Door Lock 12 Volts Door Unlock 2nd Unlock Door Lock Output - Programmable - Menu 1 Setting 3. Low Current Output. Use With Voltage Inverter Door Unlock Output - Programmable - Menu 1 Setting 3. Door Unlock Output - Programmable - Menu 1 Setting 3. 3 Pin Connector White Green Pink Blue (-) Disarmed Horn/5th Channel (+) Disconnect Negative Output When The System Is Disarmed. Programmable Output. (+) Disconnect Or Instant Start Trigger. Jumper Selections The jumpers control the output on the white wire from the six pin harness. Place the jumpers in the above order to change the output. Note: The default setting is second ignition. Output on White wire Jumper position Second Starter Position 1 Second Accessory Position 2 Second Ignition Position 3 Back View Of Module Jumpers 321 5 Installation Guide QUICK START INSTALL Step 1 - Connect All Of the Following Wires 6 Pin Power Connector Yellow Green Red Red Blue White Starter Output Heater Output 12 power Input 12 power Input Ignition 1 Output Selectable Output Connect To The Vehicles Starter Wire. Connect To The Vehicles Accessory Wire. Connect to Constant 12 Volt Power Source- High Current. Connect to Constant 12 Volt Power Source- High Current. Connect To the Vehicles Primary Ignition. Select Jumper Position (If Necessary). See Page 5. 14 Pin Power Connector Black Pink White Green/White Blue/White White/Blue Green or Purple System Ground Brake Switch Park Lights Hood Pin Tach Siren / Horn (-) Door Input (+) Door Input Connect To Chassis Ground. Connect To (+) When Brake is Applied. Connect To (+) Park Light System. Connect To Hood Pin Switch. Connect To Tach Source. Connect To (+) Siren or Horn. Connect the Green wire to a (-) door pin system. Connect the Purple wire to a (+) door pin system. Manual Transmissions Only Black/White Park Brake Connect (-) Parking Brake Manual transmission vehicles must have a “M” Series Remote Starter Installed. Manual Transmission Units Must Be Placed Into Reservation Mode To Operate. See Page 10. Step 2- Plug-In The Module When all the connections are done, the control module can be plugged in. Before connecting the control module, make sure the ignition is in the OFF position. Plug in the 6 pin harness then the 14 pin followed by any other connectors that were used. Step 3- Auto Tach Learn 1) Make all the required wire connections and plug-in the Unit. **The park lights should flash twice upon power up. 2) Turn the Ignition Key ON. (Park Lights will turn on). 3) Start the vehicle, LED’s on the antenna will come on to confirm tach signal is detected**, then after two to ten seconds the park lights will turn off then flash twice to confirm tach learning. * The system will flash the park lights seven times if not tach learned and the start button is pressed. The system must be tach learned before remote starting. ** If the LED’s do not come on during tach learn, a proper tach signal was not detected. Note: If the park lights do not flash in auto tach learn mode it may be necessary to connect to a different tach source. For best results connect the tach wire to the coil pack or to a fuel injector wire. If necessary See Page 11. for Tach Adjustment. Activate Self Learning Impact Sensor 1) Press the LOCK button on the remote 5 times in a row. The siren should chirp 3 times and the park lights should come and stay ON. 2) While the park lights are on, strike the vehicle at the desired level to trigger the alarm. 3) The siren will respond with one chirp to confirm that the Shock Sensor is programmed. 4) Press the lock or unlock button to exit Shock Sensor learning. Your Basic Install Is Complete! 6 NOTES: 1) If the unit does not start, check the starter is not in Tach Lock Out or in Program Mode. 2) If the vehicle still does not start, check all connections and check for factory security. Your Basic Installation is Now Complete!! Installation Guide PROGRAMMING Programming Overview Program mode allows you to adjust the settings and options of your system. Your system has been intelligently designed by installers with years of experience. The system’s default settings do not require any program changes in most cases. However, this system does incorporate a highly advanced programming system that includes 4 menus with numerous options and settings that can be easily adjusted for custom installations and applications. Menu 1 - User Settings - Page 8 This program menu contains settings that adjust the way the system operates for the user. Menu 2 - Alarm Settings - Page 9 This program menu contains settings that adjust the way the system operates for the user. Menu 3 - Starter Settings - Page 10 This menu controls features and settings associated with remote car starter applications. Menu 4 - Tach Settings - Page 11 This menu allows the programming of the tach signal and the manual adjustment of that setting. Entering Program Mode To Enter Program Mode 1) Make sure ignition is in the off position. 2) Within three seconds turn the key ON - OFF - ON - OFF - ON. Leave in the “ON” position. 3) Press and release the Program Button on the antenna one time. 4) The park lights will come on and the siren will chirp to confirm entering Program Mode. 5) Select the Desired Program Menu: Press Button #1 Lock User Options Page 8 Press Button #2 Unlock Alarm Option Page 9 Press Button #3 Start Remote Start Options Page 10 Press Button #4 Aux Tach Adjustment Menu Page 11 6) The selected mode will be confirmed by a siren chirp and one park light flash. 7) The Program Menu may be changed at any time by pressing the transmitter buttons as above, this allows the installer to change a setting from one menu, then quickly jump to another menu and change another setting without re-entering the Program Mode. 8) To exit Program Mode, Turn the ignition key “OFF” or wait 30 second and the system will exit automatically. This will be confirmed by one long siren chirp and park light flash. Note: If unit does not enter Program Mode, turn the ignition off for five seconds and repeat steps 1-4. ** The first ignition(Blue wire) MUST be connected to the vehicle’s first ignition wire. If it is not connected it will not be possible to enter the Program Modes. Changing the Programmable Settings To Select and Change A Program Setting: 1) Enter Program Mode. 2) Select the desired Program Menu. (See pages 8 - 11) 3) Press & release the Program Button the correct number of times to select the desired Program Setting(as listed on pages 8 - 11). The park lights will flash and the siren will chirp to indicate the current setting that is selected. 4) Press and hold the Program Button until the parking lights / siren confirm the selected setting. The park lights will flash and the siren will chirp to indicate the option selected within the setting. 5) Turn the ignition key “Off” to exit Program Mode. NOTE: This procedure is listed in detail below each program setting on pages 8 - 11 of this manual. SYSTEM RESET STEP 1 - Within three seconds turn the key ON-OFF-ON-OFF-ON (Leaving Key ON). STEP 2 - Press and release the Program Button. STEP 3 -The park Lights will turn ON. STEP 4 - Press the Program Button a second time and hold for 8 seconds until the park lights flash and the siren will chirps three times. The system is now re-set to factory defaults. NOTE: Reset to defaults does not delete the transmitters from memory. 7 Installation Guide PROGRAMMING PROGRAM MODE - USER SETTINGS Enter User Program Mode - See Page 7 for details on entering program mode Setting 1- Ignition Auto Lock 1 Ignition Lock & Unlock Enabled 2 Ignition Lock Only *3 Ignition Auto Lock Disabled 1 Light Flash 2 Light Flashes 3 Light Flashes Doors Lock / Unlock when the key is turned On/ Off Doors Lock when ignition key is turned ON only Doors do not Lock or Unlock with Ignition key Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flash) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. Setting 2- Horn Honk Settings 1 Lock & Unlock chirps Disabled 2 Lock & Unlock chirps Enabled *3 All chirps enabled 1 Flash 2 Flashes 3 Flashes Honks for Panic and Car Finder Mode only. Honks for Lock, Unlock, Panic and Car Finder Mode Only. Honks for Lock, Unlock, Start, Panic and Car Finder Mode. Press the Program Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. Setting 3- Door Lock Options 1 Double Pulse Unlock 2 3 Second Lock & Unlock *3 0.75 Second Pulses 1 Flash 2 Flashes 3 Flashes Single .75sec.Lock pulse and double Unlock Pulse 3 second pulses for Lock & Unlock 0.75 second pulses for Lock and Unlock Press the Program Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. Setting 4 -Sensor - Enable / Disable 1 Sensors Disabled * 2 Sensors Enabled 1 Flash 2 Flashes Impact Sensors Disabled Impact Sensors Enabled - Normal Operation Press the Program Switch 4 times to select setting 3 (This will be confirmed by 4 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change Setting 5 - Passive / Active Arming 1 Passive Arming 1 Flash System Auto Arms 30 seconds after last door is closed 2 Active Arming With Rearm 2 Flashes System Auto-Arms if unlock is pressed and no door is opened within 30sec * 3 Active Arming 3 Flashes Alarm Arms Only with Transmitter Press the Program Switch 5 times to select setting 1 (This will be confirmed by 5 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. Setting 6 - Active / Passive Locks 1 No Auto-Lock with Passive Arm *2 Doors Auto-Lock with Passive 1 Flash 2 Flashes Doors do not auto-lock with passive arming DOORS LOCK WHEN PASSIVE ARMING Press the Program Switch 6 times to select setting 1 (This will be confirmed by 6 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. 8 Installation Guide PROGRAMMING PROGRAM MODE - ALARM SETTINGS Enter Alarm Program Mode - See Page 7 for details on entering program mode Setting 1 - Car Finder / 5th Channel 1 Car Finder OFF 1 Light Flash Car Finder Mode Disabled *2 Car Finder ON 2 Light Flashes Car Finder Mode Enabled Note: To operate the 5th channel on button #4, setting 7 must be programmed for 5th channel output. Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flash) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. Setting 2 - Secure Valet Mode 1 Secure Valet Active 2* Normal Valet Active 1 Flash 2 Flashes Valet only if ignition “ON” and valet switch held for 15 seconds Valet if ignition “ON” and valet switch held for 5 seconds Press the Program Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes) Press and hold the Proram Switch until you receive the appropriate # of park light flashes and/or horn honks Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. Setting 3 - Parking Light Output 1 30 Second Parking Lights on Disarm 2 Negative Park Light 3* Normal Parking Lights 1 Flash 2 Flashes 3 Flashes Park Lights on for 30 seconds on disarm Switches the Park Light and the Trunk Release (3rd Channel) Outputs 2 Park Light Flashes on disarm Press the Program Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. Setting 4 - Horn Honk Timing - Pink wire on 3-pin white 1 5ms 1 Flash Short (Quiet) Pulses 2 20ms 2 Flashes Long (Loud) Pulses *3 10ms 3 Flashes Normal (Medium) Pulses Press the Program Switch 4 times to select setting 3 (This will be confirmed by 4 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. Setting 5 - 4th Channel Settings- White/Green on 4-pin square 1 Pulsed 2 Latched *3 Active 1 Flash 2 Flashes 3 Flashes Pulsed for 0.75 seconds upon 4th Channel Activation Latched until repeated or ignition “ON” Active for as long a button is held on Transmitter as long as held Press the Lock and Start buttons together to activate the 4th Channel Output. Press the Program Switch 5 times to select setting 1 (This will be confirmed by 5 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. Setting 6 -Car Jack Mode 1 Door & Button 1 Flash Car Jack is activated upon Button 4 or Door open while Ignition is “ON” 2 Door, Button 4 2 Flashes Car Jack is upon Button 4 or Door open or ignition “ON” and Ignition *3 Car Jack OFF 3 Flashes No Car Jack Functions Press the Program Switch 6 times to select setting 1 (This will be confirmed by 6 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. Setting 7 - Horn / 5th Channel 1 5th Channel 1 Flash Pulsed output when activated by button #4 2 Horn Honk 2 2 Flashes Horn Honk Output - Full Alarm ONLY *3 Horn Honk 1 3 Flashes Horn Honk with Arm & Disarm Chirps Press the Program Switch 7 times to select setting 7 (This will be confirmed by 7 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. 9 Installation Guide PROGRAM MODE - STARTER SETTINGS Enter Starter Program Mode - See Page 7 for details on entering program mode Setting 1- Special Door Lock/ Unlock Operations 1 Chrysler / VW Re-Arm 1 Flash Unlock pulse before start and a lock pulse after start 2 GM Auto Re-Lock 2 Flashes Lock pulse after remote starter shuts off 3* Normal Operation 3 Flashes No additional re-lock pulses Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash) Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps. Release the Program Button. Press momentarily to move to next program step or repeat to change selection. Setting 2- Gas/ Diesel Mode- Blue Wire on 14-Pin 1 Diesel Glow Plug 1 Flash Waits a Maximum of 3:20 second before starting. 2 Timed Delay 2 Flashes Ignition ON for 10 seconds before engaging remote starter 3* Gas Mode operation 3 Flashes Waits 2 seconds before engaging starter output Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes) Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps. Release the Program Button. Press momentarily to move to next program step or repeat to change selection. Setting 3- Rearm Output- Yellow Wire on 14-Pin 1 2 3* Type 1 Type 2 Factory Re-arm 1 Flash 2 Flashes 3 Flashes Pulse after start and with lock Pulse after start only 0.75 second pulse with lock and after shutdown Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes) Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps. Release the Program Button. Press momentarily to move to next program step or repeat to change selection. Setting 4- Run Time 1 30 Min Run Time 1 Flash Remote Starter runs for 30min when activated 2 45 Min Run Time 2 Flashes Remote Starter runs for 45min when activated 3* 15 Min Run Time 3 Flashes Remote Starter runs for 15 min when activated Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes) Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps. Release the Program Button. Press momentarily to move to next program step or repeat to change selection. Setting 5-Maximum Crank Time 1 10 Seconds 1 Flash 10 sec Max time that starter will stay engaged 2 3 Seconds 2 Flashes 3 sec Max time that starter will stay engaged 3* 5 seconds 3 Flashes 5 sec Max time that starter will stay engaged Press the Program Button 5 times to select setting 5 (This will be confirmed by 5 LED flashes) Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps. Release the Program Button. Press momentarily to move to next program step or repeat to change selection. Setting 6- Sensor Disconnect 1 Positive Input To Start 1 Flash Positive pulse will activate remote starter. 2 Positive Disconnect 2 Flashes Alarm will trigger if disconnected from 12 volts.(Same as below) 3* Positive Disconnect 3 Flashes Alarm will trigger if disconnected from 12 volts. Press the Program Button 6 times to select setting 6 (This will be confirmed by 6 LED flashes) Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps. Release the Program Button. Press momentarily to move to next program step or repeat to change selection. Setting 7- Sensor Disconnect 10 1 Positive Input To Start 1 Flash Positive pulse will activate remote starter. 2 Positive Disconnect 2 Flashes Alarm will trigger if disconnected from 12 volts.(Same as below) 3* Positive Disconnect 3 Flashes Alarm will trigger if disconnected from 12 volts. Press the Program Switch 7 times to select setting 7 (This will be confirmed by 7 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and siren chirps.. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. Continued on next page... Installation Guide Setting 8- Safety Start Mode 1 2* Safety ON Safety OFF 1 Flash 2 Flashes Must press the start button twice to remote start vehicle Press the start button once to remote start vehicle. Press the Program Switch 8 times to select setting 8 (This will be confirmed by 8 LED flashes) Press and hold the Program Switch until you receive the appropriate # of park light flashes and siren chirps. Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection. PROGRAM MODE - TACH SETTINGS See page 6 for Auto Tach Learning Setting 1- Method 2- Low Idle Tach Learning This option is used for vehicles that maintain a high or erratic idle after starting and need more that 10 seconds to establish a stable idle. Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time. Step 2 - Enter Program Mode 4 - Press the # button on the remote.(Button #4). Step 3 - Start Vehicle - Using the ignition key, make sure not to turn the key off at any time or your will exit programming. Step 4 - Press the Button - One time (Led will start flashing in single cycles) then press and hold Program (5sec). Step 5 - Release Program - Led should come on steady to indicate correct tach signal the park light will flash to confirm. Setting 2- Adjust For Over-Crank Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time. Step 2 - Enter Program Mode 4 - Press the # button on the remote.(Button #4). Step 3 - Press the Program Button - 2 times (Led will start flashing 2 times). Step 4 - Press and Hold Program - For 5 seconds until parking lights flash (each time lights flash tach is reduced 5%). Step 5 - Release Program - Exit Program Mode and remote start to test. Setting 3- Adjust For Under-Crank Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time. Step 2 - Enter Program Mode 4 - Press the # on the remote.(Button #4). Step 3 - Press the Program Button - 3 times (Led will start flashing 3 times). Step 4 - Press and Hold Program - For 5 seconds until parking lights flash (each time lights flash tach is increased 5%). Step 5 - Release Program - Exit Program Mode then remote start to test. Anti Car Jacking Mode ENSURE THAT USER IS FULLY TRAINED ON THIS FEATURE! ONLY USE THIS FEATURE WHEN SPECIFICALLY REQUESTED. ENSURE THAT USER IS TRAINED ON THE OPERATION OF THIS FEATURE IF NOT, UNWANTED RESULTS MAY ARISE. When activated, the system waits 30 seconds then flashes LED rapidly for 30 seconds, then chirps siren as a warning for 10 seconds then goes into full alarm . ACTIVATING CAR JACK MODE- Programmable - Menu 1, Setting 5. Activates upon any of the following steps: - Mode 1 & 2 While ignition is “on” press & release # button. - Mode 1 & 2 Open door while ignition is “on”. - Mode 2 only Each time ignition is turned “on” DEACTIVATING CAR JACK MODE 1. During countdown period - Turn the ignition “On” then press and release the antenna button. 2. After the alarm has activated - Turn the ignition “Off then On” then press and hold the antenna button for 8 seconds . 11 Installation Guide OPERATIONS Reservation Mode - Manual Trans. Manual Transmission Remote Starters must have both the door trigger and park brake wires connected. Most installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during the activation of the remote starter. Never disconnect or alter the switch to be always bypassed. Always use a “M” Series Remote Starter on a manual transmission vehicle. Never install a automatic Remote Starter model into a manual transmission vehicle. It is not recommended to install a remote starter on a convertible type vehicle. If doing so It is highly recommended that a radar sensor is installed to cover the proximity of the gear shift lever. If the radar sensor is tripped the remote starter will exit Reservation Mode. To enter Reservation Mode, the following steps must be followed. Step 1 - While the vehicle is running, place the transmission in neutral and apply the parking brake. Step 2 - Press and release the brake pedal. The park lights will activate. Step 3 - Turn the ignition key off and the vehicle will stay running. Step 4 - Exit the vehicle and close the door. The vehicle will then shut off. Step 5 - The vehicle can now be safely remote started. NOTE: If the vehicle has a dome light delay, the vehicle may stay running until the dome light turns off. This is normally no longer than 30 seconds. Reservation Mode will automatically be exited if the doors of the vehicle are opened. The set-up mode will then have to be repeated . Reservation Mode Must be set-up each time the vehicle is parked. Note: If the vehicle is not in Reservation Mode and the Start button is pressed, the system will flash the park lights four times slowly. Transmitter Programming Step 1 - Within three seconds turn the ignition Key ON-OFF-ON-OFF-ON - Leaving Key ON Step 2 - Press and hold the Program Switch - Parking Lights will come ON **if park-lights do not come on at this point, turn key off for 5 seconds, the repeat step 1. Step 3 - Continue to hold the Program Switch until park lights go out. Step 4 - Press the LOCK button on each of 1st car remotes and press the # button on each of the 2nd car remotes of the transmitters to be programmed. The park lights will flash once and the horn will honk once each time a new code is learned. Note: Transmitter programming must done quickly. Do not pause more than one second between each transmitter. All the transmitters to be used must be programmed at the same time. All transmitters not programmed at this time will be erased from memory for security. The system holds a maximum of 3 transmitter codes including 2nd car remote codes. You can program the same remote as a 1st car remote in one vehicle and as a 2nd car remote in a second vehicle. Battery Replacement The transmitter battery should be changed at least once every year to maintain proper operating range. Replace with quality23A 12volt Alkaline battery. Step #1 Step #2 12 Carefully remove the screw from back of the remote. Step #4 + - Step #3 Remove top case then replace the battery. Replace top case. Re-install screw. Test remote for proper operation. Installation Guide OTHER FEATURES System Service Mode ACTIVATING SERVICE MODE 1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp five times to confirm that the system is in Service Mode. 2. While in Service Mode the remote start functions will be disabled and LED’s will be “ON” steady. Door locks and trunk release are still operational. DEACTIVATING SERVICE MODE 1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp two times to confirm that the system has exited Service Mode. 2. Remote start functions will return to normal operation. Service Mode- By Remote SERVICE MODE ACTIVATED 1 - Press & Release button 4 2 - Press & Hold Button 4 for 6 seconds until Status LED comes on Steady NOTE: The siren will chirp 5 times as confirmation. SERVICE MODE DEACTIVATED 1 - Press & Release button 4 2 - Press & Hold Button 4 for 6 seconds until Status LED turns off. NOTE: The siren will chirp 2 times as confirmation. WARRANTY- Optional Three year & lifetime warranty available. See Dealer For Details. The manufacturer warrants to the original purchaser of their remote starters and alarms, that the product shall be free from defects in material and workmanship. However, should this product be proven to be defective, within a two year period from the original date of purchase, the manufacturer will, without charge to the purchaser (excluding any charges incurred to have the product delivered to the manufacturer) , repair or replace any part of the remote starter and/or alarm which the manufacturer agrees to be defective. All warranties apply on to the original purchaser and the vehicle in which it is originally installed. Repairs or replacement of defective modules shall remain at the discretion of the manufacturer. All other parts, components, accessories and/or optional equipment pertaining to the remote starter and alarm are not included in the manufacturer’s warranty. This warranty is non-transferable. Request for warranty service from any Factory Authorized Dealer must be accompanied with the original purchase receipt or have product registered by authorized dealer on manufacturer’s website. Failure to comply with any of these conditions may result in warranty being voided. This warranty does not cover the following: removal and reinstall labour charges, shipping charges, abuse, misuse, or accidental damages to the remote starter and alarm, automobile, and/or parts there of. This warranty is void upon modification, repairs, or alterations of any part of the System. The manufacturer does not guarantee or insure against theft of the vehicle or its contents. Alarm models are designed only to act as a deterrent against possible theft. This alarm may qualify for auto insurance discounts, contact your Insurance Agent for further information . The manufacturer shall not be held liable for any consequential damages due to breach of this or any other warranty, expressed, or implied. This warranty gives you specific legal rights. Your specific legal rights may vary for each region. CERTAIN DAMAGES EXCLUDED - The manufacturer expressly disclaims any liability or responsibility for incidental damages caused by the product, including economic loss, loss of use of the product, car rentals, or any other costs relating to the care and custody of the product. The manufacturer disclaims liability or responsibility for any consequential damages caused by the product or resulting from its use, including the cost of repairing or replacing other property damaged by the product or caused by its use, whether or not the product is working properly. The product is intended to deter unauthorized use of the vehicles in which it is installed. The manufacturer does not warrant that the product is fool-safe against theft and/or vandalism and/or human error or misuse. The manufacturer accepts no liability or responsibility for any damage of any kind whatsoever caused to any vehicle in which the product is installed or any resulting damage from its use. The manufacturer accepts no responsibility or liability for any damage resulting to or theft of the vehicle or its contents, caused or alleged to be caused, directly or indirectly, by failure of the product. 13 Installation Guide OPERATIONS Lock Doors & Arm The Alar m 1. 2. 3. 4. Press & release the LOCK button on the remote transmitter. The park lights will flash and the siren will chirp once. The doors will lock. The LED will start flashing within five seconds. Unlock Doors & Disarm The Alar m 1. 2. 3. 4. Press & release the UNLOCK button on the remote transmitter. The park lights will flash and the siren will chirp twice. The doors will unlock. The LED will stop flashing. Silent Arm And Disarm Together 1. Press & release the LOCK & UNLOCK buttons at the same time. 2. If the doors are locked this will unlock the doors without siren chirps, the park lights will flash two times to confirm the doors have unlocked. 3. If the doors are unlocked this will lock the doors without siren chirps, the park lights will flash one time to confirm they have locked. Trunk Release 3 sec. 1. Press and hold the UNLOCK button for three seconds. 2. The doors will unlock, continue holding the unlock button for three more seconds, the trunk release will then activate. The trunk release will be confirmed by one park light flash. 3. For safety reasons, the trunk release output will not activate when ignition key is in the “On” position. Car Finder Mode 1. Press and hold the # button for two seconds. 2. The system will flash the park lights and chirp the siren five times. 2 sec. **This feature can help find your vehicle in a crowded parking lot. Panic Mode 3 sec. 1. Press & hold the LOCK button for three seconds. 2. The park lights will flash and the siren will activate. PANIC MODE DISABLE 1. Press LOCK button to disable the panic mode and to lock the doors. 2. Press UNLOCK button to disable the panic mode and unlock the doors. 3. Panic Mode will stay activated until disabled by the remote transmitter. 2nd Car Operation 14 2nd Car Then & & & & = Press Once to Lock Doors. Continue to hold for Panic Mode. Press 2nd Time & Hold for Constant Lock Output = Press Once for Unlock Doors and Disarm the Alarm. Press & Hold for Trunk / Aux Output = Press Once for Start - (2 Times if programmed for safety start) Press & Hold for 3 seconds while running to turn off = Press & Release then press START and hold for Timer Mode Installation Guide OPERATIONS Remote Start 1. Press & release the button. 2. The Park lights will flash and the siren will chirp once. 3. When the vehicle has started, the system will flash the park lights four times and then remain “On” while the vehicle is running. 4. The vehicle will continue to run for the programmed runtime. (normally 15 minutes). EXTEND RUNTIME 1. Press & release the button while the vehicle is running. 2. The system will respond with one park light flash and one siren chirp to confirm Extended Runtime. The system will reset the run time, (normally 15 minutes). Remote Stop 1. Press and hold the button for three seconds. The remote starter will shut down. 2. The park lights will flash two times and the siren will chirp two times. 3 sec. Note: Pressing the brake pedal or opening hood will also stop the vehicle. Idle Mode While running 1. 2. 3. 4. While the vehicle is running with key, press the button. The park lights will turn on and the siren will chirp once. Turn the ignition key “off” and the vehicle will continue to run. Exit the vehicle and leave it running safely without the keys in the ignition. Lock the door while the vehicle is left running. Timer / Optional Temp Start 1.Press & release the # button, then press and hold the button for six seconds, until the parking lights turn “on”. 2. While the parking lights are “on” the start cycle can be selected. 1st 1 hour cycle or 0C Press LOCK button 1 flash 2nd-6 sec 2 hour cycle or -5C Press UNLOCK button 2 flashes 3 hour cycle or -15c Press button 3 flashes # 4 hour cycle or -25c Press button 4 flashes 3. System will start vehicle at selected cycle for up to 24 hours. 4. The temp start must have the temp sensor installed and will only trigger 1 time each 2 hours if the sensor is not installed the unit will activate the timer mode. TO CANCEL COLD START MODE 1. Press & release the # button, then press and hold the button for four seconds. 2. The park lights will flash and the siren will chirp twice. Delay Dome Light - Auto Detection If the vehicle is equipped with a factory delay dome light, the system will detect this when arming and chirp the siren 4 times 15-30 seconds after arming. This conformation will also be activated if the system is armed with the door open. Ignition Auto Locks Ignition On/Off This safety feature will lock the vehicles doors two seconds after the Ignition is turned to the on position. When the ignition key is turned to the off position the doors will unlock. Note: The system can be programmed for Ignition Lock only. In this setting the door’s will lock when the key is turned “On” and stay locked when the key is turned “Off”. 15 Installation Guide RELAY DIAGRAMS Negative Door Locks Vehicle Lock/Unlock Switch Lock To Control Relay or Actuators Un lock Green Blue Positive Type Door Locks Vehicle Lock/Unlock Switch Un Lock lock Fused +12V 87 Green 87 87a 86 Blue 87a 86 85 30 85 30 To Control Relay or Actuator 5 Wire / Reverse Polarity Type Door Locks Fused +12V 87 Green 87 87a 86 Blue Vehicle Lock/Unlock Switch 87a 86 85 85 30 Lock 30 x Cut Un lock To Actuator Cut x Vacuum Type Door Locks DIAGNOSTICS Fused +12V 87 Green 87 87a 86 Blue 87a 85 86 30 85 30 Ground Lock x Un lock Cut To Vacuum Pump Built-in Starter Disable IG2 ACC Off 16 IG1 Start Starter Disable Harness Brown wire with spade connectors. Cut x To Starter Motor or Relay Note: Connect the Starter Wire (Yellow) to the starter motor side of the starter disable.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project