DGS-3420 Series Firmware Release Notes

Add to my manuals
8 Pages

advertisement

DGS-3420 Series Firmware Release Notes | Manualzz

DGS-3420 Series Firmware Release Notes

Firmware Version: V1.50.018

Prom Code Version: V1.00.006

Published: 2013/4/10

These release notes include important information about D-Link DGS-3420 series firmware revisions. Please verify that these release notes are correct for your switch:

- If you are installing a new switch, please check the hardware version on the device label; make sure that your switch meets the system requirement of this firmware version. Please

refer to Revision History and System Requirement for detailed firmware and hardware

matrix.

- If the switch is powered on, you can check the hardware version by typing “show switch” command or by checking the device information page on the web graphic user interface.

- If you plan to upgrade to the new firmware release, please refer to the Upgrade Instructions for the correct firmware upgrade procedure.

For more detailed information regarding DGS-3420 series products, please refer to Related

Documentation .

You can also download the switch firmware, D-View modules and technical documentation from http://tsd.dlink.com.tw

.

Content:

Revision History and System Requirement ........................................................................ 2

Upgrade Instructions: .................................................................................................... 2

Upgrade using CLI (serial port) ..................................................................................... 2

Upgrading by using Web-UI.......................................................................................... 3

New Features ................................................................................................................ 4

Changes of MIB & D-View Module .................................................................................... 6

Changes of Command Line Interface ................................................................................ 6

Problem Fixed ............................................................................................................... 7

Known Issues ............................................................................................................... 7

Related Documentation .................................................................................................. 8

1

DGS-3420 Series Firmware Release Notes

Revision History and System Requirement

Firmware Version Date

Runtime: v1.00.023

Prom: v 1.00.006

Runtime: v1.00.024

Prom: v 1.00.006

Runtime: v1.50.017

Prom: v 1.00.006

Runtime: v1.50.018

Prom: v 1.00.006

2011/7/7

2011/10/7(A1)

2011/12/6(A2)

2012/12/12

2013/4/10

Model

DGS-3420-28TC

DGS-3420-28SC

DGS-3420-26SC

DGS-3420-28PC

DGS-3420-52T

DGS-3420-52P

DGS-3420-28TC

DGS-3420-28SC

DGS-3420-26SC

DGS-3420-28PC

DGS-3420-52T

DGS-3420-52P

DGS-3420-28TC

DGS-3420-28SC

DGS-3420-26SC

DGS-3420-28PC

DGS-3420-52T

DGS-3420-52P

DGS-3420-28TC

DGS-3420-28SC

DGS-3420-26SC

DGS-3420-28PC

DGS-3420-52T

DGS-3420-52P

Upgrade Instructions:

A1, A2

A1, A2

A1, A2

A1, A2

A1, A2

A1, A2

A1, A2

A1, A2

A1, A2

A1, A2

A1, A2

A1, A2

A1, A2

Hardware Version

A1

A1

A1

A1

A1

A1

A1, A2

A1, A2

A1, A2

A1, A2

A1, A2

D-Link switches support firmware upgrade via TFTP server. You can download the firmware from

D-Link web site http://tsd.dlink.com.tw

, and copy the downloaded firmware to the TFTP server folder. Please make sure that the TFTP server is accessible from the switch via networks.

Upgrade using CLI (serial port)

Connect a workstation to the switch console port and run any terminal program that can emulate a VT-100 terminal. The switch serial port default settings are as follows:

 Baud rate: 115200

 Data bits: 8

 Parity: None

 Stop bits: 1

The switch will prompt the user to enter his/her username and password. It should be noted that upon the initial connection, there is no username and password by default.

To upgrade the switch firmware, execute the following commands:

Command Function

2

DGS-3420 Series Firmware Release Notes download [firmware_from_TFTP [<ipaddr> | <ipv6addr>] src_file <path_filename 64> {[unit <unit_id> | all]} {dest_file

<pathname 64>}

Download firmware file from the TFTP server to the switch. config firmware image {unit <unit_id>} <path_filename 64> boot_up

Change the boot up image file. show boot_file

Display the information of current boot image and configuration. reboot

Example:

Reboot the switch.

DGS-3420-28TC:15# download firmware_from_TFTP 10.53.13.201 src_file c:\ DGS-3420_Series_FW_1.00.023.had dest_file c:\ DGS-3420_Series_FW_1.00.023.had

Command: download firmware_from_TFTP 10.53.13.201 src_file c:\ DGS-3420_Series_FW_1.00.023.had dest_file c:\ DGS-3420_Series_FW_1.00.023.had

Connecting to server................Done.

Download firmware...................Done. Do not power off!

Upload file to FLASH…………………………..Done.

DGS-3420-28TC:15# config firmware c:\ DGS-3420_Series_FW_1.00.023.had boot_up

Command: config firmware c:\ DGS-3420_Series_FW_1.00.023.had boot_up

Success.

DGS-3420-28TC:15# show boot_file

Command: show boot_file

-----------------------------------------------------

Unit ID : 1

Boot up firmware image : C:\DGS-3420_Series_FW_1.00.023.had

Boot up configuration file: C:\STARTUP.CFG

-----------------------------------------------------

DGS-3420-28TC:15# reboot

Command: reboot

Are you sure you want to proceed with the system reboot? (y|n) y

Please wait, the switch is rebooting...

Upgrading by using Web-UI

1. Connect a workstation installed with java SE runtime environment to any switch port of the device.

2. Open the web browser from the workstation and enter the IP address of the switch. The switch’s default IP address is 10.90.90.90.

3. Enter administrator’s username and password when prompted. It should be noted that the username and password are blank by default.

4. To update switch's firmware or configuration file, select Tools > Download Firmware from the banner.

5. Use the drop-down menu to select a unit for receiving the firmware. Select All for all units.

6. Enter the TFTP Server IP address.

3

DGS-3420 Series Firmware Release Notes

7. Enter the name of the firmware file located on the TFTP server.

8. Enter the destination path and the desired file name.

9. Tick the check box to set it as a boot up file.

10. Click “Download” button.

11. Wait until the “Current Status” displays “Done” and the “Percentage” shows “100%”.

11. To select the boot up image used for next reboot, click Network Application > Flash File

System Settings in the function tree and then click the C: drive name. When you see the files list, click corresponding “Boot Up” button to specify the firmware that will be used for next and subsequent boot up.

12. To reboot the switch, select Tools > Reboot System from the banner.

13. Select “Yes” and click “Reboot” button to reboot the switch.

New Features

Firmware New Features

4

DGS-3420 Series Firmware Release Notes

Version

V1.00.023

V1.00.024

V1.50.017

First release, please refer to datasheet and manual for detail function supported

None

1. Support configurable DHCP server option

2. Policy route support “route_preference [default | pbr]” command

3. Weighted Random Early Detection

4. Bandwidth control minimum granularity down to 8Kbps

5. Support null route redistribute to dynamic routing protocol

6. Storm control support to configure per packet type threshold on same port

7. Support advanced power saving (LED Shut-off/ Port Shut-off/ System

Hibernation)

8. IMPB v3.95

9. Support show DDM TX/RX power

10. Support IPv6 route longer than 64bit prefix

11. Selective Q-in-Q

12. Secure FTP server for IPv4

13. Support unicast NLB

14. DSCP to CoS mapping

15. Support public key for SSH authentication

16. Support to set accounting server IP address

17. Support enable/disable IP directed broadcast

18. Support response of broadcast SNMP Get packet

19. Support DHCPv6 Server Screening

20. Support to select IPIF as the source address for TFTP/Telnet/Tacacs/Radius

21. DHCP relay per port

22. VRRP

23. LBD v4.05

24. IPv6 Route Redistribution for RIPng

25. Support packet counter for stacking port

26. TACACS+ accounting for command logging

28. Support storm control log/trap for drop mode

29. IGMP authentication support “auth_accounting”, “auth only” or “accounting only” states

30. Alarm port output

31. Support DEM-CB700S

32. Support to disable a trunk member port

33. Support SSL intermediate CA certificate

34. ERPS enlarge to 12 rings (instances)

35. Enhance the information of “show ports <portlist> media_type” command

36. DHCP client support option 12

37. SNTPv6

38. DHCPv6 Prefix Delegation

39. DNSv6

40. Support Framed-IP-Address Radius attribute

41. Enlarge PoE maximum power limit to 760W for DGS-3420-28PC

42. Support 802.3az Energy-Efficient Ethernet (Hardware version B1 and later)

None V1.50.018

5

DGS-3420 Series Firmware Release Notes

Changes of MIB & D-View Module

The new features of MIB file are also included in the corresponding D-View module. Please download the D-View module on http://tsd.dlink.com.tw

. For detailed changes of MIB content, please refer to the modification history in each MIB file.

Firmware

Version

V1.00.023

V1.00.024

MIB File New Features

V1.50.017

V1.50.018

First release, please refer to datasheet for detail MIB supported

None

Genmgmt.mib wred.mib

1. Support total number of ARP entries

2. Port utilization by percentage

3. Support to respond a broadcast SNMP GET packet

Weighted Random Early Detection

SFTPServer.mib

Rfc2787.mib

Equipment.mib

QoS.mib ddm.mib

QinQ.mib

Secure FTP server for IPv4

VRRP

1. Support advanced power saving

2. Support 802.3az Energy-Efficient Ethernet (Hardware version B1 and later)

1. Bandwidth control minimum granularity down to 8Kbps

2. DSCP to CoS mapping

Support show DDM TX/RX power

L3mgmt.mib

L2mgmt.mib

Support selective Q-in-Q

1. IPv6 Route Redistribution

2. IP directed broadcast

IGMP authentication support auth & accounting, auth only or accounting only

PktStormCtrl.mib

IPMacBind.mib

Filter.mib

AAC.mib

1. Support configure per packet type threshold on same port

2. Support storm control log/trap for drop mode

IMPB v3.95

DHCPv6 Server Screening

1. Support to set accounting server IP address

2. Support command accounting

LBD v4.05 LBD.mib

SSH.mib

DHCPRelay.mib

DHCPServer.mib

NLB.mib policyRoute.mib

SrcIPIf.mib

None

Support public key for SSH authentication

DHCP relay per port

Support configurable DHCP server option

Support unicast NLB

Policy route support to choose the priority of route table or

PBR

Support to select IPIF as the source address for

TFTP/Telnet/Tacacs/Radius

Changes of Command Line Interface

The section below only shows command line changes that may bring backward compatibility issues with configuration settings for previous version of firmware.

6

DGS-3420 Series Firmware Release Notes

Any new feature commands that do not have backward compatibility issues are not included in the below section.

Firmware

Version

Changes

V1.00.023

V1.00.024

V1.50.017

V1.50.018

First release

None

None

None

Problem Fixed

Firmware

Version

V1.00.023

V1.00.024

V1.50.017

V1.50.018

Problems

First release

1. Modify CPU GPIO pin setting on DGS-3420-28SC/28TC/52T

2. Modify RTC trickle register to reduce charging time

1. When setting "config multicast vlan_filtering_mode", the outputs of “show config effective” and “show config modified“ are incorrect.

(DUSA20120628000003)

2. When using a SSH vulnerability tool (Rubyinstaller), DGS-3420 will be rebooted automatically(

DI20121012000005

)

3. After enabling LACP and traffic segmentation, ARP packets will be forwarded even if the port is not in traffic segmentation forward list (

DRU20121015000004

)

4. When connecting TFTP server from Mgmt interface and normal interface at the same time, download firmware from TFTP will be failed. (

DI20120622000007

)

5.

When typing “

config stp mst_config_id name PGS1 revision_level ”, DGS-3420 will be

rebooted automatically (

DRU20120523000009

)

6. CPU high because of DHCP relay packet was looped on ingress port

(

DEUR20121023000007

)

7. IPTV froze because of some multicast packets are dropped

(

DEUR20121023000007

)

8. DGS-3420 doesn’t insert option 82 in unicast DHCP request

(

DEUR20121023000007

)

9. DGS-3420 doesn’t transmit DHCP release packet when enabling DHCP relay (

DEUR20121023000007

)

10. DGS-3420 will drop double tagged IGMP query packet on untagged port

(

DEUR20121023000007

)

Fix the software bug which will encounter test failure result when processing the test program in production line.

* D-Link tracking number is enclosed in ()

Known Issues

Firmware

Version

V1.00.023

V1.00.024

Issues

None

None

Workaround

7

DGS-3420 Series Firmware Release Notes

V1.50.017

V1.50.018

None

None

Related Documentation

- DGS-3420 Series Web UI Reference Guide Release 1.5

- DGS-3420 Series CLI Reference Guide Release 1.5

- DGS 3420_Series_FW_HW Installation Guide 1.5

8

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement