Pioneer HTZ-55DV System - H:\Documents\49503HTZ55DVOperatingInstructions

Add to my manuals
68 Pages

advertisement

Pioneer HTZ-55DV System - H:\Documents\49503HTZ55DVOperatingInstructions | Manualzz

DVD SURROUND SYSTEM

HTZ-55DV

Operating Instructions

2

En

IMPORTANT

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

These labels can be found on the unit’s bottom panel.

CAUTION

Ces étiquettes se trouvent sur le fond de l’appareil.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION

DANGER D'ELECTROCUTION

NE PAS OUVRIR

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

CAUTION

This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.

CAUTION

• Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

• The use of optical instruments with this product will increase eye hazard.

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

This product contains a laser diode of higher class than 1. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product.

Refer all servicing to qualified personnel.

The following caution appears on your unit.

Location: bottom of the unit

THE STANDBY/ON BUTTON IS SECONDARY CONNECTED AND

THEREFORE DOES NOT SEPARATE THE UNIT FROM MAINS POWER

IN STANDBY POSITION.

CLASS 1

LASER PRODUCT

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while.

When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

CAUTION :

VORSICHT :

ADVARSEL :

VARNING :

VARO! :

LASER RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM.

LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET

NICHT DEM STRAHL AUSSETZEN!

LASERSTRÅLING VED ÅBNING UNDGÅ

UDSÆTTELSE FOR STRÅLING.

LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD BETRAKTA EJ STRÅLEN.

AVATTAESSA ALTISTUT LASERSÄTEIL YLLE.

ÄLÄ KATSO SÄTEESEN.

VRW1697

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However, the method of connecting and operating the unit is the same.

Installation Precautions

• Install components so that there are no obstructions above or either side of them, or by ventilation holes. Also install

10cm away from the wall as shown in the figures.

Components feature ventilation holes on the bottom so do not install on thick pile carpets or other surfaces that may block them.

• Use a vacuum cleaner periodically to clean the port of the subwoofer to keep it free of dust.

Line Voltage Selector Switch

Only multi-voltage models are provided with this switch.

There is a Voltage Selector. Australian model is not provided with this switch. Be sure this is set correctly.

Mains voltages in Saudi Arabia are 127 V and 220 V only.

Always check that this selector is set properly before plugging the power cord into the wall outlet.

1. Disconnect the power cord.

2. Use a small-sized screwdriver (flat blade).

3. Insert the screwdriver into the groove on the voltage selector, and adjust the voltage selector.

110V

-127V

220V

-230V

240V

CAUTION

DISCONNECT POWER

SUPPLY CORD,

BEFORE CHANGING

THE VOLTAGE

VOLTAGE SELECTOR

CAUTION 240V

Power source voltage is factory adjusted

240 volts. If your area is different, change voltage selector setting.

Powered subwoofer unit (S-DV55SW)

25 cm (10 in.) or more

DVD Tuner system (XV-DV55)

10 cm (4 in.) or more

10 cm (4 in.) or more

25 cm (10 in.) or more

10 cm

(4 in.) or more

Rear: 10 cm (4 in.) or more

Rear: 10 cm (4 in.) or more

3

En

4

En

Contents

1 Before You Start

Features ................................................................................ 5

Using this manual ................................................................ 5

Hints on installation ............................................................ 6

Avoiding problems with condensation ............................... 6

Moving the system ............................................................... 6

Discs compatible with this system ...................................... 6

DVD Video regions .............................................................. 6

2 Controls and Displays

Front panel .......................................................................... 7

Display ................................................................................. 7

Remote control .................................................................... 8

3 Getting Started

Introduction ........................................................................ 10

Switching on and setting the clock .................................... 10

Switching the time format ................................................ 10

Setting up for surround sound .......................................... 11

Setting the speaker distances ............................................ 11

Balancing the surround sound ........................................... 12

Using the setup navigator .................................................. 13

Playing DVD Video discs ..................................................... 14

Playing CDs ......................................................................... 16

Playing Video CDs .............................................................. 17

Listening to the radio ......................................................... 18

Improving FM stereo sound ............................................... 18

Listening to other components ......................................... 19

Switching between digital and analog sources ................. 19

4 Shaping the Sound

Adjusting the bass and treble ........................................... 20

Using P.Bass ....................................................................... 20

Using sound modes ........................................................... 21

Listening to surround-sound sources with room effects .............................................................. 21

Listening to other sources with room effects .................. 22

Listening at low volume ..................................................... 22

Adjusting channel volume levels ....................................... 22

5 Using the DVD Player

Introduction ....................................................................... 23

Finding what you want on a disc ....................................... 23

Switching camera angles (DVD only) ............................... 24

Switching subtitles (DVD only) ......................................... 24

Switching audio language (DVD only) ............................. 24

Programming playlists ....................................................... 24

Programming a DVD playlist ............................................. 25

Programming a CD/Video CD playlist .............................. 26

More programming options .............................................. 26

Using repeat play .............................................................. 27

Using random play ............................................................ 27

DVD .................................................................................... 27

CD/Video CD .................................................................... 27

Bookmarking a place in a disc (DVD/Video CD) ............. 28

Memorizing disc settings (DVD only) ............................... 28

Displaying disc information .............................................. 29

7 Using the Timer

Using the wake up timer ................................................... 31

Activating/deactivating the wake up timer ...................... 31

Checking the timer settings .............................................. 32

Using the sleep timer ........................................................ 32

8 Making a Recording

Making an audio or a video recording ............................. 33

Making a digital recording ................................................ 33

9 DVD Settings

Using the Setup menu ....................................................... 34

OSD settings ...................................................................... 34

Setup Menu Mode ............................................................. 34

OSD language .................................................................... 34

On Screen Display (Expert) .............................................. 34

Video settings .................................................................... 35

TV Screen Size ................................................................... 35

Adjusting the video quality ............................................... 35

Still Picture (Expert) ......................................................... 35

Angle Indicator (Expert) ................................................... 35

Audio settings .................................................................... 36

Dolby Digital Out .............................................................. 36

Linear PCM Out ................................................................. 36

Language settings .............................................................. 36

Audio Language ................................................................. 36

Subtitle Language .............................................................. 37

Auto Language ................................................................... 37

DVD Language (Expert) .................................................... 38

Subtitle Off (Expert) ......................................................... 38

Subtitle Display (Expert) .................................................. 38

Miscellaneous settings ...................................................... 39

Parental Lock ..................................................................... 39

Changing the parental lock level ...................................... 39

Changing your password ................................................... 40

Background Color (Expert) .............................................. 40

10 Advanced Sound Settings

Advanced sound settings .................................................. 41

LFE attenuator ................................................................... 41

Dynamic Range Control .................................................... 41

Dual-mono setting ............................................................. 42

11 Controlling Other Equipment

Setting up the remote control .......................................... 43

Setting up using component presets ................................ 43

Reassigning a MULTI CONTROL button ........................... 44

Learning directly from other remote controls ................. 45

Deleting a single command ............................................... 46

Deleting all commands for a component ......................... 46

Controlling a component while playing another ............. 46

Clearing all remote control settings ................................. 47

Checking preset codes ...................................................... 47

CD/MD/CD-R/VCR/LD player controls .......................... 48

Cassette deck controls ...................................................... 49

DVD/DVR player controls ................................................. 50

DTV controls ...................................................................... 51

Cable TV/satellite TV/TV controls ................................... 52

6 Using the Tuner

Saving station presets ....................................................... 30

Listening to station presets .............................................. 30

12 Connecting Up

Connecting to a TV with the supplied video cord ........... 53

Connecting to a TV with an S-Video cord ........................ 53

Playing your TV through this system ................................ 53

Watching TV ...................................................................... 53

Connecting Other Components ....................................... 54

Connecting an audio recorder .......................................... 54

Connecting Outdoor Antennas ........................................ 55

Connecting an Outdoor AM Antenna .............................. 55

Connecting an Outdoor FM Antenna .............................. 55

13 Additional Information

Setting the display brightness .......................................... 56

Switching the TV system output ....................................... 56

Taking care of your system ................................................ 57

Disc lens cleaner ................................................................ 57

Taking care of your discs ................................................... 57

Storing discs ...................................................................... 57

Discs to avoid .................................................................... 57

Glossary ............................................................................. 58

DVD language code list ..................................................... 59

Preset Code List ................................................................ 60

Troubleshooting ................................................................ 64

Resetting the player .......................................................... 66

Screen sizes and disc formats ........................................... 66

Component features & functions ..................................... 67

DVD tuner system .............................................................. 67

Powered subwoofer unit .................................................... 67

Display unit ........................................................................ 67

Specifications .................................................................... 68

1 Before You Start

Features

÷ Superlative audio performance with Dolby

Digital* and DTS** software

The HTZ–55DV delivers breathtaking sound quality with

Dolby Digital and DTS discs, and is also compatible with

96kHz/24-bit PCM sources.

÷ New graphical Setup Navigator

Setting up your home theater is easy using the graphical

Setup Navigator. Answer the questions that appear on-screen and the Setup Navigator makes the necessary audio, video and language settings for you.

• This product incorporates copyright protection technology that is protected by method claims of certain

U. S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is prohibited.

* Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. © 1992-1997 Dolby Laboratories.

All rights reserved.

** “DTS” and “DTS Digital Surround” are trademarks of

Digital Theater Systems, Inc. Manufactured under license from Digital Theater Systems, Inc.

Using this manual

This manual is for the HTZ–55DV DVD Surround System. It is divided into several sections: information for before you start using the system (chapters 1–2); getting started using the system (chapters 3–4); more advanced features (chapters 5–

8); system settings and preferences (chapters 9–10); using this remote control with other components (chapter 11); connecting up the system and using this system with external components (chapter 12). Chapter 13 provides additional information, including a glossary of terms used in this manual, and a troubleshooting section.

5

En

1 Before You Start

Hints on installation

We want you to enjoy using this unit for years to come, so please bear in mind the following points when choosing a suitable location for it:

Do...

✓ Use in a well-ventilated room.

✓ Place on a solid, flat, level surface, such as a table, shelf or stereo rack.

Don’t...

✗ Use in a place exposed to high temperatures or humidity, including near radiators and other heat-generating appliances.

✗ Place on a window sill or other place where the system will be exposed to direct sunlight.

✗ Use in an excessively dusty or damp environment.

✗ Place directly on top of an amplifier, or other component in your stereo system that becomes hot in use.

✗ Use near a television or monitor as you may experience interference—especially if the television uses an indoor antenna.

✗ Use in a kitchen or other room where the system may be exposed to smoke or steam.

✗ Use on a thick rug or carpet, or cover with cloth—this may prevent proper cooling of the unit.

✗ Place on an unstable surface, or one that is not large enough to support all four of the unit’s feet.

Avoiding problems with condensation

Condensation may form inside the system if it is brought into a warm room from outside, or if the temperature of the room rises quickly. Although the condensation won’t damage the system, it may temporarily impair its performance. For this reason you should leave it to adjust to the warmer temperature for about an hour before switching on and using.

Moving the system

If you need to move the system, first switch it off and unplug from the wall outlet. Never lift or move the unit during playback—discs rotate at a high speed and may be damaged.

Discs compatible with this system

Any disc that displays one of the following logos should play in this system. Other formats, including DVD-RAM, DVD-

ROM, DVD-Audio, CD-ROM, SACD and Photo CD will not play.

Single or double sided / Single or double layer.

Dolby Digital, DTS, MPEG or Linear PCM digital audio.

MPEG-2 digital video.

Discs are generally divided into one or more ‘titles’. Titles are further subdivided into ‘chapters’.

Single sided / Single layer. 12 cm or 8 cm (5" or 3") discs.

Linear PCM digital audio. (Also compatible with finalized CD-

Recordable discs.)

Discs are divided into ‘tracks’.

This system can play CD-R and CD-RW discs recorded with audio. However, depending on the quality of the initial recording, and the condition of the disc, you may find that not all discs will play successfully. (For example, if the disc is scratched or dirty, or if the player’s pickup lens is dirty.) Some

CD-R and CD-RW discs may need to be finalized* before playing successfully.

* Check with the instruction manual of the recording component used to make the CD-R or CD-RW disc for finalization procedures.

Single sided / Single layer. 12 cm or 8 cm (5" or 3") discs.

MPEG-1 digital audio. MPEG-1 digital video. Discs are divided into ‘tracks’.

DVD Video regions

2

ALL

All DVD Video discs carry a region mark on the case somewhere that indicates which region(s) of the world the disc is compatible with. Your DVD system also has a region mark, which you can find on the rear panel. Discs from incompatible regions will not play in this system. Discs marked

ALL

will play in any player.

6

En

Front panel

1 2 3 4

2 Controls and Displays

5

11 10

1

STANDBY / ON – Press to switch the system on or into standby.

2

Standby/timer indicator – Lights red when the system is in standby; lights in green if the timer has been set.

3 Disc tray

4

DVD function indicator – Lights when the system is set to the DVD function.

5

0 OPEN/CLOSE – Press to open or close the disc tray.

6

PHONES – Plug in a pair of headphones for private listening.

Display

1 2 3 4 5 6 7

9 8 7 6

7

3 – Press to start or resume playback.

8

8 – Press to pause a disc that’s playing, or restart a paused disc.

9

7 – Press to stop the disc.

10 VOLUME controls – Use to adjust the overall system volume.

11 FUNCTION – Press to select the input source (DVD, tuner, etc.)

8 9 10 11 12 13

20 19 18 17

1

CONDITION – Indicates playback settings (condition) are memorized.

2

TITLE – Indicates a title playback.

3

TOTAL – Indicates total playback time of disc side currently playing.

4

LAST MEMO – Indicates that the location on a disc where you last stopped watching is memorized.

5

REMAIN – Indicates remaining playback time.

16

6

7

CHP/TRK – Indicates playback of a chapter or track.

ANGLE – Indicates multi-angle playback.

15 14

12 DSP – Lights when a DSP mode or Advanced Theater effect is on.

13 DTS – Indicates DTS playback.

14 Mono – Lights when the mono FM reception mode is selected.

15 Stereo Station Reception – Lights during stereo broadcast station reception.

16 Station Reception – Lights during broadcast station reception.

17 Sleep Timer – Lights when the sleep timer is ON and during sleep timer operation.

8

LFE – Lights if the current Dolby Digital or DTS source has a

Low Frequency Effects (LFE) channel.

9

Channel indicators – Shows which channels are recorded on the disc loaded.

18 Wake-up Timer – Lights when the wake-up timer is ON, and flashes during wake-up timer operation.

19 Timer ON – Lights when the wake-up timer is ON, and flashes during wake-up timer operation.

10 2 DIGITAL – Indicates Dolby Digital playback.

11 2 PRO LOGIC – Indicates Dolby Pro Logic playback.

20 96 kHz – Lights during playback of a source with a sampling frequency of 96kHz.

7

En

2 Controls and Displays

Remote control

Many of the remote control’s buttons have more than one function. To make things easier, the button names are colorcoded:

• Sky blue – DVD and Video CD functions

• Yellow – tuner functions

• Pale purple – TV functions

• Green – sound and other system settings

• Orange – DVD and CD functions (press

SHIFT

first to access)

• Pink – Cable TV functions

To learn how a particular button on the remote works, look up the function name in the alphabetical list below. Buttons labeled only with symbols appear first.

2/DTS – Press to switch the Theater mode when listening to Dolby Digital or DTS DVD discs. For other discs, press to switch on Dolby Pro Logic.

7 – Press to stop a disc playing.

3 – Press to start or restart a disc playing.

8 – Press to pause or restart a disc.

¶ – Press twice within 10 seconds to start recording on a recorder connected to the AUDIO 1 or VIDEO 1 outputs.

4 – Press to skip back tracks/chapters/titles on a disc.

¢ – Press to skip forward tracks/chapters/titles on a disc.

e – Use for slow motion reverse playback and frame reverse with a DVD or Video CD.

E – Use for slow motion forward playback and frame advance with a DVD or Video CD.

1 – Press and hold to reverse scan through a disc.

¡ – Press and hold to forward scan through a disc.

– Press to switch the camera angle during a multi-angle scene on a DVD disc.

0/10 – Use as zero, or 10 when selecting tracks/chapters/ titles from a DVD, Video CD or CD, or radio station presets.

19 (number buttons) – Use to select tracks/chapters/titles from a DVD, Video CD or CD, or radio station presets.

>10 – Use when entering a track/chapter/title or radio station preset number greater than 10. After pressing, input the required number ( >10, 2, 4 for 24, and so on).

A

A-1 – Press to switch to an audio component connected to the AUDIO 1 inputs/outputs.

A-2 – Press to switch to an audio component connected to the AUDIO 2 inputs.

A-B – Use to set the start and end points of a repeating loop.

AUDIO (sky blue) – Press to switch to another audio channel or language on the disc playing.

B

BAND – Press to switch between AM and FM bands when listening to the radio.

C

C – Press to clear settings or entries.

CH+ / CH– – Press to change channels on a satellite tuner, cable box, VCR, etc.

CH SELECT – Press to select the speaker channel when setting up your system for surround sound.

8

En

2 Controls and Displays

CONDITION – Press to save the current settings for the

DVD disc playing. Next time you load the disc, the player will automatically revert to these settings.

D

DISP (orange) – Press to switch the displayed information for the DVD or CD loaded.

DISP (green) – Press to display the time.

DSP – Use to select a DSP room effect mode.

DVD – Press when you want to play a DVD, Video CD or CD.

E

ENTER – Use to confirm menu choices, setups and so on.

ENTER/DISC – Used for controlling external components only. Function varies with the external component.

EXIT – Press to exit the guide feature of cable TV.

F

FL DIMMER – Use to adjust the brightness of the fluorescent display.

FQ+/– – Use to manually tune to radio stations.

FUNCTION – Press to switch the system function (DVD, tuner, Video 1, etc.), without changing the remote control mode.

G

GUIDE – Press to access the guide feature on cable TV.

L

LAST MEMORY – Use to bookmark the current place on a DVD or Video CD disc, and to start playing from a previously bookmarked place on a disc.

M MENU – Press to display a DVD or Video CD disc menu for navigating the contents of a disc.

MIDNIGHT – Press to switch the Midnight listening mode on or off. This mode aids listening at low volume.

MONO – Press to listen to a stereo FM radio broadcast in mono (this can improve the sound quality). Press again to switch back to stereo.

MUTE – Press to mute the speakers. Press again to cancel the mute.

P

P.BASS – Press to switch P.BASS on or off. Switch on for extended bass.

PAGE +/– – Press to display the next/previous page of a cable TV guide.

PGM – Use to program a playlist for a DVD, Video CD or CD.

R

RDM – Use to set the random play mode when playing a

DVD, Video CD or CD.

REMOTE SETUP – Press to put the remote into setup mode. Use to setup the remote to control other components in your system.

REPEAT – Use to set the repeat mode for a DVD, Video CD or CD.

RETURN – Use to return to the previous level of a DVD disc menu, or to display the menu of a Video CD playing in PBC mode.

S

SEARCH MODE – Use to select a search mode (title, chapter, track, time) for a DVD, Video CD or CD.

SETUP – Press to show the on-screen display for making audio, video and other settings for DVD playback.

SHIFT – Press to access the remote functions printed in orange on the remote. After pressing, the shift mode remains in effect for up to 10 seconds.

SLEEP – Use to select a preset time until the system switches into standby.

SOUND CONTROL – Press to adjust the bass or treble.

SOURCE – Press to switch on/off a source component

(tape or MD deck, for example) connected to this system. (You need to set up the remote first for this to work).

ST +/– – Press to switch the station preset when listening to the radio.

STATION MEMORY – Use to save the current frequency as a station preset.

SUBTITLE – Press to switch the subtitle language on a multilingual DVD disc.

SYS – Press to switch the remote from TV control to system control without changing the source function of the system.

SYSTEM – Press to switch the system on or into standby.

SYSTEM VOLUME – Use to adjust the overall system volume.

T

TEST TONE – While setting up the channel levels of the speakers, press to start or stop the test tone.

TIMER/CLOCK ADJ – Use to set the timer or clock.

TOP MENU – Press to display the top level menu of a DVD disc.

TUN – Press to switch to tuner for listening to the radio.

TV – Press to switch the remote from system, DVD, tuner, etc.

control to TV control.

TV – Press to switch your TV on/off. (You need to set up the remote first for this to work).

TV CHANNEL – Use to change the TV channel.

TV INPUT – Press to switch the TV input (from internal tuner, to VCR1, and so on).

TV VOL – Use to adjust the TV volume.

V

V-1 – Press to switch to a video component connected to the

VIDEO 1 inputs/outputs.

V-2 – Press to switch to a video component connected to the

VIDEO 2 inputs.

9

En

3 Getting Started

Introduction

This chapter covers switching on and setting the clock, using the Setup Navigator to set some basic preferences, using all the basic controls for playing discs, and using the tuner.

Switching on and setting the clock

This system has a built in clock, which needs to be set to be able to use the timer features.

1 Press SYSTEM to switch on.

2 Press SYS then TIMER/CLOCK ADJ.

3 Press the

@ or # button until you see CLOCK ADJUST in the

display.

4 Press ENTER.

If you've just connected the power, the display shows 12:00 AM, with the hour blinking.

5 Use the

% and fi buttons to set the hour, then press ENTER.

6 Use the

% and fi buttons to set the minute, then press ENTER.

The display blinks for 2 seconds to indicate that the time has been set.

Tip

Press

SYS

then

DISP

anytime to see the clock when the system is on or in standby.

Switching the time format

You can display the clock in either 12 or 24-hour format.

1 Switch the system into standby.

2 Press SYS then TIMER/CLOCK ADJ.

3 Press the

@ or # button until you see CLOCK 12 HOUR or

CLOCK 24 HOUR in the display.

4 Use the

% and fi buttons to select 12 or 24.

5 Press ENTER.

10

En

3 Getting Started

Setting up for surround sound

You can use this system right out of the box for surround sound with just the default settings.

However, for really great surround sound, we recommend that you spend a few minutes making some settings that match this system to your listening room. These include setting the distances from your listening position to your speakers, and balancing the speaker volumes. Unless you change the layout of your speakers or main listening position, you only need to make these settings once.

Setting the speaker distances

1 Press SYS, then SETUP.

This puts the remote into surround setup mode.

2 Press the

@ or # button until

you see FRONT in the display.

7 Use the

% and fi buttons to set

the distance from your main listening position to the surround speakers.

Ideally, your listening position should be equidistant from the surround speakers.

The default setting is 3m. You can adjust the range from 0.3 m to 9.0m in steps of

0.3m.

3 Use the

% and fi buttons to set

the distance from your main listening position to the front speakers.

Ideally, your listening position should be equidistant from the two front speakers.

The default setting is 3m. You can adjust the range from 0.3 m to 9.0m in steps of

0.3m.

4 Press

# to move on to the

CENTER speaker setting.

8 Press ENTER to make the last setting and exit.

• The setting mode is automatically exited if no operation is performed within 20 seconds.

• There are several other settings that you can make from the System Setup menu to further tailor your surround sound. See chapter 10 for more on this.

• The speaker distance settings have no effect when the Dolby/DTS mode is set to VIRTUAL SURR1 or

VIRTUAL SURR2. See page 21 for more on Dolby/DTS modes.

5 Use the

% and fi buttons to set

the distance from your main listening position to the center speaker.

The default setting is 3m. You can adjust the range from 0.3 m to 9.0m in steps of

0.3m.

6 Press

# to move on to the

SURROUND speakers setting.

11

En

3 Getting Started

Balancing the surround sound

You can further improve surround sound performance by balancing the levels from the subwoofer, center and surround speakers relative to the front left/right speakers. To help you judge the sound level of each speaker a test tone is played through each speaker in turn (make sure that there are no headphones connected). Adjust the levels until they all sound equal.

The levels you set here will apply to all Dolby/DTS modes. However, you can set levels independently for each DSP mode.

Note: it may not be possible to accurately adjust the subwoofer level using this method. You may prefer to leave it on its default setting and adjust it to your liking later when playing surround-sound sources.

1

Press SYS then 2/DTS.

The Dolby/DTS mode can be set to any-thing except

SURROUND OFF

. (No test tone is output if the Dolby/DTS mode is set to

SURROUND OFF

.)

2 Set the volume to a moderate level.

3 Press TEST TONE to start the test tone then adjust the master volume to a suitable level.

The test tone plays through each speaker in turn:

• Front left

• Center

• Front right

• Surround right

• Surround left

• Subwoofer

4 Use the

% and fi buttons to adjust the level of a speaker as the

test tone plays.

For best results, sit in your main listening position when doing this. You can adjust each speaker in the range of +/-10dB.

5 When you're done, press TEST TONE to turn off the test tone.

12

En

3 Getting Started

Using the setup navigator

Before playing any discs, we strongly recommend using the Setup Navigator. This makes all the basic system settings for you.

1 Press SYSTEM to switch on.

Also turn on your TV and make sure that it is set to the correct video input.

• If a disc already loaded starts playing, press

7 to stop it.

2 Press DVD then SETUP.

The Setup Navigator on-screen display (OSD) appears:

5 Select the type of TV you have.

Audio Video Language

Setup Navigator

General

TV Connection

TV Type

Widescreen (16:9)

Standard (4:3)

Audio Video Language

Setup Navigator

General

Setup Navigator Start

Auto Start Off

Move

ENTER

Select

SETUP

Exit

Move

ENTER

Select

SETUP

Exit

• See Aspect ratio in the glossary on page

58 if you’re unsure of the difference between widescreen and standard TVs.

6 Confirm all the settings.

Audio Video Language

Setup Navigator

General

Exit Setup Navigator

Save Changes

Delete Changes

Start Again

Navigate all of the following OSDs using these controls:

%, fi – cursor up/down

ENTER – select the highlighted menu option

@ – go back to the previous question

The control possibilities for the current

OSD are shown at the bottom of each screen.

Move

ENTER

Select

SETUP

Exit

7 Press SETUP to exit.

Congratulations, you’ve set up your system!

If you want to use the Setup Navigator again at any time, it is available from the

General menu. Also, each individual setting can be changed using the appropriate menu option — chapter 9 explains all menu options in detail.

3 Select START.

Remember: Press

ENTER

to select an option.

• If you decide you don’t want to use the

Setup Navigator, select

Auto Start

Off here instead.

4 Choose an OSD menu language.

Audio Video Language

Setup Navigator

General

Language

OSD Language

English français

Español

Move

ENTER

Select

SETUP

Exit

13

En

3 Getting Started

Button

3

8

7

Playing DVD Video discs

Only the basic controls for playback of DVD discs are covered here. Further functions are detailed in the next chapter.

1 Press DVD.

Alternatively, press

FUNCTION

on the front panel to select DVD.

2 Load a DVD disc.

• Press

0

OPEN

/

CLOSE

to eject the disc tray.

• Place a disc in the tray, label side face up, making sure it is seated properly in the disc guide.

• Press

0

OPEN

/

CLOSE

to close the disc tray. Many DVD-Video discs start playing automatically.

3 Basic playback controls*

Button What it does

Numbers

If the disc is stopped, playback starts from the selected title number. If the disc is playing, playback jumps to the start of the selected chapter number.

>10

e

Selects titles/chapters 11 and over.

(For example, for 24, press >10 , 2,

4.)

Press & hold for about 2 seconds to start slow-motion reverse scanning.

Change the speed using the e and

E buttons.

When playing, press once to pause; reverse a single frame with each subsequent press.

E

Press & hold for about 2 seconds to start slow-motion forward scanning.

Change the speed using the e and

E buttons.

When playing, press once to pause; advance a single frame with each subsequent press.

1

¡

4

¢

What it does

Starts/resumes playback

Pauses a disc that’s playing or restarts a paused disc

Stops playback. Display shows

RESUME

(press

3 to start playback again from the last place stopped).

Press & hold for fast reverse scanning. (After 5 seconds, scanning continues even after releasing the button: press

3 to resume normal playback.)

Press & hold for fast forward scanning. (After 5 seconds, scanning continues even after releasing the button: press

3 to resume normal playback.)

Skips to the start of the current chapter, then to previous chapters.

Skips to the next chapter.

* While using the DVD, you may see the

or mark displayed on-screen.

means that the operation is not allowed by the system.

means that the operation is not allowed by the disc.

14

En

4 Basic disc menu controls

Some DVD discs contain menus.

Sometimes these are displayed automatically when you start playback; others only appear when you press

MENU

or

TOP MENU

.

Control What it does

TOP MENU Displays the ‘top menu’ of a DVD disc — this varies with the disc.

MENU

Displays a DVD disc menu — this varies with the disc and may be the same as the ‘top menu’.

RETURN

Returns to the previously displayed menu screen.

On some DVD-Audio discs featuring browsable pictures, press to display the browser screen.

Cursor buttons

Moves the cursor around the screen

ENTER

Selects the current menu option

Numbers

Selects a numbered menu option

(some discs only)

5 Eject and remove the disc before switching off.

3 Getting Started

15

En

3 Getting Started

Playing CDs

Only the basic controls for playback of CDs are covered here. Further functions are detailed in the next chapter.

1 Press DVD.

Alternatively, press

FUNCTION

on the front panel to select DVD.

2 Load a CD.

• Press

0

OPEN

/

CLOSE

to eject the disc tray.

• Place a disc in the tray, label side face up, making sure it is seated properly in the disc guide.

• Press

0

OPEN

/

CLOSE

to close the disc tray.

3 Basic playback controls:

Button

¡

4

¢

3

8

7

1

What it does

Starts/restarts playback

Pauses a disc that’s playing or restarts a paused disc

Stops playback

Press & hold for fast reverse scanning.

Press & hold for fast forward scanning.

Skips to the start of the current track, then to previous tracks.

Skips to the next track.

Numbers

Starts playback from the selected track number.

>10

Selects tracks 11 and over. (For example, to select track 24, press >10, 2, 4.)

4 Eject and remove the disc before switching off.

16

En

3 Getting Started

Playing Video CDs

Only the basic controls for playback of Video CDs are covered here. Further functions are detailed in the next chapter.

Button What it does

1 Press DVD.

Alternatively, press

FUNCTION

on the front panel to select DVD.

Numbers

Starts playback from the selected track number.

2 Load a Video CD.

• Press

0

OPEN

/

CLOSE

to eject the disc tray.

• Place a disc in the tray, label side face up, making sure it is seated properly in the disc guide.

• Press

0

OPEN

/

CLOSE

to close the disc tray.

>10

E

Selects tracks 11 and over. (For example, to select track 24, press

>10, 2, 4.)

Press & hold for about 2 seconds to start slow-motion forward scanning.

Change the speed using the e and

E buttons.

When playing, press once to pause; advance a single frame with each subsequent press.

3 Basic playback controls

Many Video CDs contain menus, from which you control playback. This is called

PlayBack Control, or PBC, and if the disc features it, the PBC menu will be the first thing you see when you start playback (see

Basic PBC menu controls on the right for how to navigate these).

4 Basic PBC menu controls

If the Video CD features PBC menus, navigate them using the following controls. To switch off PBC, press

7 then restart playback using a number button to select a track directly.

Button

3

8

7

1

¡

4

¢

What it does

Starts/resumes playback

Pauses a disc that’s playing or restarts a paused disc

Stops playback. Display shows

RESUME

(press

3 to start playback again from the last place stopped).

Press & hold for fast reverse scanning. (After 5 seconds, scanning continues even after releasing the button: press

3 to resume normal playback.)

Press & hold for fast forward scanning (After 5 seconds, scanning continues even after releasing the button: press

3 to resume normal playback.)

Skips to the start of the current track, then to previous tracks.

Skips to the next track.

Button What it does

RETURN

Displays the PBC menu.

Numbers

Selects a numbered menu option.

4

Displays the previous menu page (if there is one).

¢

Displays the next menu page (if there is one).

3

Press to select an item from a PBC menu.

5 Eject and remove the disc before switching off.

17

En

3 Getting Started

Listening to the radio

The following steps show you how to tune in to FM and AM radio broadcasts using the automatic (search) and manual (step) tuning functions. Once you are tuned to a station you can memorize the frequency for recall later—see Saving station presets on page 30 for more on how to do this.

1 Press TUN.

Alternatively, press

FUNCTION

on the front panel to select Tuner.

2 Press BAND to select the FM or AM band.

Each press switches the band between FM and AM.

3 Tune to a station.

There are three ways to do this:

• Automatic tuning

To search for stations in the currently selected band, press and hold either the

FQ

+ or

FQ

button for about a second. The system will start searching for the next station, stopping when it has found one. Repeat this step to search for other stations.

• Manual tuning

To change the frequency one step at a time, press the

FQ

+ /

FQ

buttons.

• High speed tuning

Press and hold the

FQ

+ or

FQ

button for high speed tuning, releasing the button once you reach the frequency you want.

Improving FM stereo sound

If you’re listening to a stereo FM broadcast, but find that there is a lot of noise because of a weak signal, try switching to mono.

• Press MONO to switch between mono and stereo.

When listening in mono, the indicator lights in the display.

18

En

3 Getting Started

Listening to other components

This system has several audio/video inputs for you to connect other components, such as a VCR, MD deck, and so on. See chapter 12 for more on connecting up other components.

1 Switch to the source you want to watch/listen to.

There are four external inputs you can connect components to. Select them using the multi-control buttons:

V-1 (Video 1)

V-2 (Video 2)

A-1 (Audio 1)

A-2 (Audio 2)

Alternatively, you can use the

FUNCTION

button on the front panel, or press

SYS

then

FUNCTION

on the remote.

2 Start playing the source component.

Switching between digital and analog sources

Both digital and analog inputs are available when Audio 1 or Video 2 is selected as the source. The Input Select setting tells the system which input it should use.

See page 54 for more on connecting other components to this system.

Note: This system can only play Dolby Digital, PCM (32, 44.1, and 48kHz) and DTS digital audio formats. For digital sources using other formats, use analog connections and select

INPUT ANALOG

.

1 Press AUDIO A-1 or VIDEO V-2 (for the input you want to set).

The settings for the Audio 1 and Video 2 inputs are completely independent.

2 Press SYS then SETUP.

3 Press the

@ or # button until you see INPUT in the display.

4 Use the

% and fi buttons to select the input to use.

INPUT OPTICAL

– the optical digital input is used as the source

INPUT COAXIAL

– the coaxial digital input is used as the source (this setting is only available for VIDEO 2)

INPUT ANALOG

– (default setting) the analog inputs are used as the source

5 Press ENTER to make the setting.

19

En

4 Shaping the Sound

Adjusting the bass and treble

The simplest way to shape the sound is by adjusting the amount of bass and treble.

Note: The bass and treble controls have no effect when using the DSP modes, or when the Dolby/DTS mode is set to anything other than

AUTO

,

STANDARD

or

SURROUND

OFF

.

1 Press SYS then SOUND

CONTROL.

2 Use the

@ or # buttons to select BASS or TREBLE.

3 Use the

% and fi buttons to adjust the sound.

You can see the current level in the display.

4 Press ENTER to set the level.

Using P.Bass

In addition to the standard controls for adjusting bass and treble, this system has a

P.Bass feature. Switch this on to further extend the bass.

Note: P.Bass has no effect when listening through headphones.

• Press SYS then P.BASS to switch P.BASS on or off.

20

En

4 Shaping the Sound

Using sound modes

The sound modes allow you to add various room-type sound effects to your DVDs, CDs and other sources. These effects process the sound in various ways to simulate different spaces such as a theater, or concert hall.

For Dolby Surround, Dolby Digital or DTS surround sources, such as DVDs, use the

Advanced Theater effects to add room effects to the sound; for stereo-only sources, such as audio CDs, use the DSP modes. As well as choosing between effects, you can also adjust how strong the effect sounds. Often, a more subtle effect level enhances the sound better than turning it right up. Experiment to see what works best for you.

Listening to surroundsound sources with room effects

Effects modes

Switch on the Dolby/DTS mode when you play a Dolby Surround, Dolby Digital or

DTS encoded source.

Auto – For digital sources, decoding is automatically selected according to the source: Dolby Digital, DTS, Dolby

Pro Logic, 2-channel stereo, etc. No extra effects are added to the source.

Analog sources are played in the same way as the Surround Off setting.

Standard – As Auto, except that 2channel (analog or digital) sources are processed using Dolby Pro Logic for surround-sound effects.

Musical – Concert hall sound.

Drama – Classic, mid-size movie theater sound.

Action – Large, modern movie theater sound.

Virtual Surround 1 – Virtual surround sound from just the main front stereo speakers and a subwoofer.

Use this mode if you can't use the surround speakers.

Virtual Surround 2 – Virtual surround sound if you have connected the surround speakers, but are using them in front of the listening position.

Rear Wide – Widens the rear channel soundstage.

Surround Off – All sources are played through only the front left and right speakers, and the subwoofer. No effects are added.

Note: The Dolby/DTS mode cannnot be used with 96kHz/24-bit sources, or in combination with DSP effects.

1

Press SYS then 2/DTS to

select a sound mode.

Each press changes the mode as follows:

AUTO

STANDARD (surround on, with no

Advanced Theater effect)

MUSICAL

DRAMA

ACTION

VIRTUAL SURR.1

VIRTUAL SURR.2

REAR WIDE

SURROUND OFF (surround off)

To adjust the effect level when using one of the Advanced

Theater effects:

1 Press SYS then SOUND CON-

TROL.

2 Use the

% and fi buttons to

adjust the effect level.

You can adjust the effect level in the range of 10 to 90.

21

En

4 Shaping the Sound

Listening to other sources with room effects

You can add room effects to audio CDs and other stereo sources using the DSP modes.

Different effects work better with different kinds of music, so don’t be afraid to experiment a little.

There are seven DSP effects to choose from:

Hall 1 – Large, wood-paneled concert hall sound.

Hall 2 – Large, stone-walled concert hall sound.

Jazz – Live jazz club sound.

Dance – Nightclub sound.

Theater 1 – Classic, mid-size movie theater sound.

Theater 2 – Large, modern movie theater sound.

Simulated Stereo – Virtual stereo for mono sources.

Notes

• The DSP effects cannnot be used with

96kHz/24-bit sources, or in combination with the Dolby/DTS mode.

• When playing stereo sources with DSP effects switched off, there is no sound from the surround and center speakers.

1 Press SYS then DSP to select a sound mode.

Each press changes the mode as follows:

HALL

1

HALL

2

JAZZ

DANCE

THEATER

1

THEATER

2

SIMULATED STEREO

DSP OFF (no effects added)

To adjust the effect level when using one of the DSP effects:

1 Press SYS then SOUND CON-

TROL.

2 Use the

% and fi buttons to

adjust the effect level.

You can adjust the effect level in the range of 10 to 90.

22

En

Listening at low volume

When the volume is low, surround effects tend to become less than satisfactory. Turn the Midnight listening mode on to enjoy quality surround sound even at low volumes.

• Press SYS then MIDNIGHT to switch Midnight listening mode on/off.

Adjusting channel volume levels

Depending on your room and where you’re sitting, you may want to adjust the relative volumes of one or more speakers for a more balanced sound. You can do this in any mode, including the Dolby Digital/

DTS, DSP, and stereo modes. Settings that you make in any sound mode are completely independent and don’t affect any other mode.

Notes

• Each DSP effect has its own set of channel level settings.

• The channel levels you set for the

Dolby/DTS mode apply to all Advanced

Theater effects.

• The headphone level is not affected by the channel level settings.

1 Press SYS then CH SELECT.

Adjustments to the channel volume levels will affect only the current sound mode.

2 Use the

@ and # buttons to

select a channel to adjust.

The display shows the channel and its current setting.

• Remember that not all channels are available in all sound modes.

3 Use the

% and fi buttons to

adjust the volume of the current channel.

For best results, sit in your main listening position when doing this. You can adjust each speaker in the range of +/-10 dB.

4 When you're done, press

ENTER.

5 Using the DVD Player

Introduction

• Most of the functions covered in this chapter apply to DVD discs, Video CDs and CDs, although the exact operation of some varies slightly with the kind of disc loaded.

• When playing DVD discs, if the or icon appears on-screen when you try and use a particular function, either the player or the disc doesn’t allow the use of that function.

• When playing Video CDs, some of the functions are not available in PBC mode. If you want to use them, stop the disc first and restart by inputting a track number on the remote control.

Finding what you want on a disc

You can directly access any point on a disc using one of the search modes. Use these search modes while a disc is playing, or when it’s stopped — playback immediately starts from the point specified.

1 Press SHIFT, then SEARCH MODE repeadedly to choose between:

Title search (DVD only)

Chapter/Track search

Time search (DVD and Video CD only)

Off

2 Enter the title/chapter/track number or time (minutes & seconds).

For example, for title 4, press 4.

For chapter/track 12, press 1 , 2.

For 45 minutes into the disc, press 4 , 5 , 0 , 0.

3 Press

3 to start/restart playback.

23

En

5 Using the DVD Player

Switching camera angles

(DVD only)

Some DVD discs feature scenes shot from two or more angles—check the box for details: it should be marked with a icon if it contains multi-angle scenes. When these scenes are playing, a camera icon appears on-screen and the

ANGLE

indicator lights in the display.

• To switch the camera angle, press SHIFT then .

• To hide the TV angle indicator, choose Angle Indicator > Off from the Video menu (see page 35).

Switching subtitles

(DVD only)

Many DVD discs have subtitles in one or more languages — the box will usually tell you which subtitle languages are available. You can switch subtitle language anytime during playback.

• To display/switch the subtitle language, press SUBTITLE repeatedly.

• To switch off subtitles, press SUBTITLE then C (Clear).

• To set subtitle preferences, see page 37.

Switching audio language

(DVD only)

When playing a DVD disc recorded with dialog in two or more languages, you can switch audio language anytime during playback.

Note: With some discs, you can select the audio language from the DVD disc menu.

Press menu then follow the on-screen menus to make your selection.

• To display the current audio language, press AUDIO.

• To switch the audio language, press AUDIO repeatedly.

• To set audio language preferences, see page 36.

Programming playlists

Programming a playlist means telling the player which tracks, and in what order, you want played. You can program a sequence of up to 24 tracks, playing tracks more than once if you like.

Input the playlist via an on-screen display, using the cursor buttons and number buttons to navigate the screen and enter title/chapter numbers.

24

En

5 Using the DVD Player

Programming a DVD playlist

1 Press SHIFT then PGM.

2 Use the

@ and # buttons to

select Program Chapter or

Program Title.

If you select Program Chapter, move the cursor down ( fi) to highlight Title, then enter a title number (all the chapters you program will be from this title).

4 If you want to memorize the playlist, move the cursor down to Program Memory and set it to ON.

The player can memorize playlists for up to 24 DVD discs.

Program Chapter Program Title

Current:

Title

09

––

––

07 18 –– –– –– –– ––

–– –– –– –– –– –– ––

–– –– –– –– –– –– ––

Program Memory On

Off

Move

Title

7

Chapter

1 (Chapter 1 ~ 49)

1

PROGRAM

Exit

Program Chapter Program Title

Current: Title

Title

––

7 Chapter 1

1 (Chapter 1~ 18)

–– –– –– –– –– –– ––

––

––

–– –– –– –– –– –– ––

–– –– –– –– –– –– ––

Program Memory – Off

Move

ENTER

Play

PROGRAM

Exit

Program Chapter Program Title

Current: Title

2(/20)

––

––

–– –– ––

–– –– ––

––

––

––

––

––

––

––

––

–– –– –– –– –– –– –– ––

Program Memory – Off

Move

ENTER

Play

PROGRAM

Exit

5 Press ENTER to start playback immediately, or SHIFT then

PGM to exit if you want to start playback later.

3 Move the cursor down to the playlist window and start entering chapter/title numbers.

For titles/chapters 1 to 10, use the corresponding number button. For 11 and over, use the >10 button (>10, 2, 4 for

24, etc.)

Program Chapter Program Title

Current: Title

Title

09

––

7 Chapter 1

1 (Chapter 1~ 18)

07 18 –– –– –– –– ––

–– –– –– –– –– –– ––

–– –– –– –– –– –– –– ––

Program Memory – Off

Move

ENTER

Play

PROGRAM

Exit

Program Chapter Program Title

Current: Title

2(/20)

09

––

07 18 ––

–– –– ––

––

––

––

––

––

––

––

––

–– –– –– –– –– –– –– ––

Program Memory – Off

Move

ENTER

Play

PROGRAM

Exit

25

En

5 Using the DVD Player

Programming a CD/Video CD playlist

1 Press SHIFT then PGM.

Program Track

––

––

––

Current: Track

Total Time

–– –– ––

–– –– ––

––

1(/10)

0.00

––

––

––

––

––

––

––

––

–– –– –– –– –– ––

Move

ENTER

Play

PROGRAM

Exit

2 Start entering track numbers.

For tracks 1 to 10, use the corresponding number button. For 11 and over, use the

>10

button ( >10, 2, 4 for 24, etc.)

3 Press ENTER to start playback immediately, or SHIFT then PGM to exit if you want to start playback later*

* You can’t start program playback later with a PBC Video CD: press

ENTER

to start.

More programming options

There are several other options available when programming/using playlists.

• To view the playlist, press SHIFT then PGM.

• To put a pause in the playlist, press

8 instead of a number.

• You can’t program two pauses in succession, or start/end a playlist with a pause.

• To delete an entry from the playlist, position the cursor on the title/chapter/track number and press C (Clear).

• To insert an entry into the playlist, position the cursor where you want the title/chapter/track to appear, then enter its number.

All the following entries move up one.

• To add an entry to the end of the playlist, press SHIFT then PGM, enter the title/chapter/track number, then press SHIFT and PGM again.

• To add the currently playing title/chapter/track to the playlist, press SHIFT then hold PGM for about 2 seconds.

• If there is no current playlist, a new one is created. (For DVD: if the last playlist programmed was for titles, then a title playlist is created; otherwise a chapter playlist is created.)

• To delete the playlist, press

7 to stop playback, then press C

(Clear).

• To delete a memorized DVD playlist, load the DVD disc, press

SHIFT then PGM, then change the Program Memory option to

Off. Press ENTER to confirm.

26

En

Using repeat play

Use the repeat function to repeat the current track/chapter/title, the whole disc, or loop between two points anywhere on the disc. You can set the repeat mode in normal or program play modes. Set or change the repeat mode while the disc is already playing.

Note: you can’t use repeat and random play at the same time.

• To set or change the repeat mode, press REPEAT.

The repeat mode is shown on-screen. Just stop on the one you want.

• To cancel repeat play, press C

(Clear), or set the repeat mode to OFF.

• To loop a section of a disc, press A–B to mark the start point, then again to mark the end point and start looping.

• To cancel looping, press A–B again.

• To repeat a section of a disc once, press A–B to mark the start point, then press

3 to

mark the end point and loop.

Button What it does

REPEAT

Sets the repeat mode. For DVD the repeat modes are title or chapter; for CDs or Video CDs, track or all tracks.

A–B

C

Sets the start point of a loop to repeat. Press again to mark the end point and start the loop repeating.

• To play the loop just once, mark the end point by pressing

3

Cancels repeat mode (playback continues).

7

Cancels repeat mode (playback stops).

5 Using the DVD Player

Using random play

To play titles/chapters/tracks in a different order each time you play a disc, use the random play mode. Each title/chapter/ track plays just once, but in a random order. Set the random play mode while the disc is playing or stopped.

Note: you can’t use random play together with program or repeat play.

DVD

• To start playing chapters at random, press SHIFT then

RDM, then ENTER.

• To start playing titles at random, press SHIFT, then RDM twice, then ENTER.

CD/Video CD

• To start playing tracks at random, press SHIFT then

RDM.

Button

RDM

ENTER

¢

4

C

7

What it does

CD/Video CD: Starts random playback of tracks.

DVD: Sets random mode (chapter or title). Press ENTER to start.

DVD only: Starts random playback.

Starts a new random title/chapter/ track.

Returns to the start of the current title/chapter/track (you can’t go further back than this).

Cancels random mode (playback continues normally).

Cancels random mode (playback stops).

27

En

5 Using the DVD Player

Bookmarking a place in a disc

(DVD/Video CD)

If you watch only part of a DVD disc with the intention of picking up later where you left off, you can bookmark the place then resume playback at a later date without having to manually search for the right place.

You can use this feature for up to five discs (after that the oldest bookmark is deleted to make space for a new one).

• At the point from which you want to resume playback next time, press LAST MEMORY, then stop the disc (

7).

• To resume playback, load the disc and press LAST MEMORY. (If the disc started auto playback, stop it first.)

• To clear the last memo position of the disc loaded, press LAST

MEMORY then C (Clear) while Last Memory is displayed onscreen.

Note: Bookmarking also works with Video CD, but for one disc only, and you must leave the disc in the system—opening the disc tray erases the memory. Last Memory may not work reliably with some PBC Video CDs.

Memorizing disc settings

(DVD only)

If you have a particular set of preferences for a disc, you can memorize them using the

Condition Memory function. Once memorized, your settings will be recalled automatically whenever you load that disc. The system can store settings for 15 discs; after this, memorizing another replaces the oldest one stored.

The settings memorized are:

• On Screen Display (page 34)

• Subtitle language (page 37)

• Audio language (page 36)

• Video quality (page 35)

• Angle indicator (page 35)

• Parental lock level (page 39)

• To memorize settings for the current disc, press SHIFT then

CONDITION during playback.

• To recall memorized settings, just load the disc.

The display shows

COND

_

MEMORY

and Condition Memory appears on-screen.

• To clear memorized settings, load the disc and press C (Clear) while Condition Memory is displayed on-screen.

28

En

5 Using the DVD Player

Displaying disc information

Various track, chapter and title information, as well as the video transmission rate for

DVD discs, can be displayed on-screen while a disc is playing, or while it’s stopped.

• To show/switch the information displayed, press DVD then DISP.

• When a disc is playing, the informa-tion appears at the top of the screen. Keep pressing

DISP

to change the displayed information.

Play

Tr. Rate :

3

DVD display showing the video transmission rate

9.2

• When a disc is stopped, all title/chapter, or track information for the disc loaded appears on-screen. Press

DISP

again to exit the screen.

Information: DVD

Title

01

02

03

04

05

1/1

DVD-Video

Chapter Title

1~ 30

1~ 21

1~ 46

1~ 12

1~ 8

06

07

08

09

Chapter

1~ 10

1~ 13

1~ 5

1~ 4

DISPLAY

Exit

Information: Compact Disc

Total Time

Track Time

01

02

3.32

2.58

6.30

1/1

CD/Video CD

DISPLAY

Exit

• To display the time remaining on the DVD disc playing, press and hold DISP.

The time remaining is displayed for as long as you hold down the DISP button. Release to revert to the previous display.

29

En

6 Using the Tuner

Saving station presets

If you often listen to a particular radio station, it's convenient to have the receiver store the frequency for easy recall whenever you want to listen to that station. This saves the effort of manually tuning in each time. This system can save up to 30 station presets.

When saving FM frequencies, the receiver also saves the mono setting (see page 18).

1 Tune to a station you want to memorize.

See Listening to the radio on page 18 for more on how to do this.

2 Press STATION MEMORY.

3 Press ST+ or ST– to select a station preset number.

Alternatively, use the number buttons (use the >10 button for numbers over 10).

If you use the number buttons, you can skip step 4.

4 Press STATION MEMORY again to save the station preset.

Repeat these steps to save up to 30 station presets.

Listening to station presets

Having saved up to 30 station presets (see above for how to do this), you can be listening to a station with a couple of button presses.

1 Press TUN to switch to the tuner.

2 Use ST+ or ST– to select the station preset you want to listen to.

Alternatively, use the number buttons (use the >10 button for numbers over 10).

• If the system is left disconnected from the AC power outlet for a lengthy period, the station presets will be lost and will have to be re-programed.

30

En

7 Using the Timer

Using the wake up timer

You can use the timer as an alarm clock to wake up to the sound of a disc loaded or the radio. If you have an external component operated by a separate timer, you can also set the source function to that.

Once the timer is active, it will switch the system on everyday at the set time.

Unlike an ordinary alarm clock, you need to set a system switch off time as well as a switch on time.

1 Select the source that you’d like to wake up to.

For a disc, press

DVD

; for the radio press

TUNER

. For an external component, press the corresponding button.

2 Load a disc or tune to a radio station, then set the volume.

If you selected an external component, make the appropriate timer settings for it.

When setting the volume, remember things sound louder first thing in the morning!

3 Press SYS then TIMER/CLOCK

ADJ.

4 Press the

@ or # button until

you see WAKE-UP SET in the display.

5 Press ENTER.

The display shows a switch on time with the hour blinking.

6 Set the switch on time.

Use

% and fi to set the hour then press

ENTER

. Set the minute in the same way, pressing

ENTER

to finish.

• If you make a mistake, press

TIMER

/

CLOCK ADJ

and start again from step 3.

7 Set the switch off time.

Set in the same way as the switch on time, pressing

ENTER

to finish.

• If you make a mistake, press

TIMER

/

CLOCK ADJ

and start again from step 3.

8 Check the settings you just made.

The display should indicate that you set the wake up timer, then show the on time, the off time, the function (DVD, etc.), and the volume.

• There is no direct way to edit the timer settings. If you see that some timer setting is not what you’d intended, you’ll need to start the process again from the top.

9 Switch the system into standby.

The timer will not work if the system is left on!

The standby light on the front panel lights green to indicate that the timer has been set.

Activating/deactivating the wake up timer

To activate the wake up timer, set the timer to

ON

. To deactivate it, set the timer to

OFF

.

1 Press SYS then TIMER/CLOCK

ADJ.

2 Press the

@ or # button until

you see TIMER ON or TIMER

OFF in the display.

3 Press ENTER.

31

En

7 Using the Timer

Checking the timer settings

If you’ve set the wake-up timer, you can check the settings anytime. Here’s how to do it.

1 Press SYS then TIMER CLOCK/

ADJ.

2 Press the

@ or # button until

you see TIMER CHECK in the display.

3 Press ENTER.

The display shows the timer settings:

On time

Off time

Function (DVD, etc.)

Volume

Using the sleep timer

The sleep timer switches the system into standby after a specified amount of time so that you can fall asleep without worrying about the stereo being left on all night. If you've also set the wake up timer this is important since the wake up timer will only work if the system is in standby.

1 Press SYS.

2 Press SLEEP to set the time until the system goes into standby.

Press repeatedly to switch between:

SLEEP AUTO

– this setting is only available when the system is playing a

CD *

SLEEP

90

(minutes)

SLEEP

60

(minutes)

SLEEP

30

(minutes)

SLEEP OFF

(cancels the sleep timer)

The sleep timer indicator ( ) lights when the sleep timer is active.

* not available when a Video CD is in PBC mode, or if you're playing a CD or Video

CD in repeat mode. If you set a disc playing in repeat mode after setting the sleep timer to

AUTO

, it automatically switches to the 90 minute setting.

• Once the sleep timer is set, you can check the time left by pressing

SLEEP

.

• T

O

cancel the sleep timer, switch the system into standby, or select

SLEEP

OFF

(as described above)

• If you switch to a different source when

SLEEP AUTO

is set, the system will automatically go into standby a minute later.

32

En

8 Making Recordings

Making an audio or a video recording

The following steps show you how to make an audio or a video recording from the built in tuner, DVD, CD or from an audio or video source connected to the system

(CD player, satellite tuner, etc.). Recordings can be made to a recorder connected to the

AUDIO

1

or

VIDEO

1

inputs/outputs.

The system's volume, balance, bass, treble,

Midnight and surround sound settings have no effect on the recording.

Notes

• You can't record a source connected to the digital inputs from the analog outputs.

• You can't record DTS encoded discs from the analog outputs.

1 Select a source to record.

Use the

MULTI CONTROL

buttons on the remote, or the

FUNCTION

button

(remote or front panel) to select the source.

2 Prepare the program source.

Tune to the radio station, load the CD, etc.

For a video recording load the video, etc.

3 Insert a blank tape, MD, etc.

into the recorder connected to either AUDIO 1 or VIDEO 1 and set the recording levels.

Refer to the instructions that came with the recorder if you are unsure how to do this. Most video recorders set the audio recording level automatically — check your video's instruction manual if you are unsure whether yours has manual controls.

4 Start recording, then start playback of the source component.

Making a digital recording

The system has one optical digital audio output (for

AUDIO

1

). If you want to make a digital recording from this system hook up this optical output to the optical input of your digital recorder. The source

(CD, DVD, etc.) must be digital also; this system doesn’t convert analog inputs to digital. If you’re recording from an external digital component, also make sure that you’ve selected the digital input for that component (see page 19).

Note: If you want to record DVD disc, check that the digital output settings correct. See page 36 for detailed instructions.

1 Select DVD or VIDEO V-2 as the digital source to record.

Use the

MULTI CONTROL

buttons on the remote, or the

FUNCTION

button

(remote or front panel) to select the source.

2 Prepare the program source.

Load the CD, MD, etc.

3 Insert a blank MD, CD-R, etc.

into the recorder connected to the optical output of AUDIO 1.

4 Start recording, then start playback of the source component.

See the instructions that came with your recorder for detailed instructions on recording.

33

En

9 DVD Settings

Using the Setup menu

The Setup menu gives you access to all the

DVD system settings. When in DVD mode, press

SETUP

to display/leave the menu and the cursor buttons and

ENTER

to navigate and select options. The controls for each menu are shown at the bottom of the screen.

If an option is greyed out it means that it cannot be changed at the current time.

This is usually because a disc is playing.

Stop the disc, then change the setting.

The current setting for any option is marked with a colored box. The color of the box indicates what kind of disc the setting is applicable to: blue for DVD only; yellow for DVD and Video CD; green for any type of disc.

OSD settings

Setup Menu Mode

• Default setting:

Basic

The Basic setup menu gives you access to the more commonly used settings. It also features an information bar which tells you more about what the currently highlighted option means.

Set to

Expert for access to all settings.

Audio Video Language General

Setup Menu Mode Expert

Setup Navigator

Basic

Parental Lock – Level 8

Change menu mode

Move

SETUP

Exit

OSD language

• Set in Setup Navigator (default:

English)

Choose between OSD menus in the languages offered.

Audio Video Language General

Auto Language – On

Select the On Screen Language

Move

SETUP

Exit

On Screen Display

(Expert)

• Default setting: Position - Normal

When watching DVD discs recorded in 4:3 format (‘regular’ TV size) on a widescreen

TV, it can be difficult to see the operation displays ( Play, Stop, Resume, etc.) at the top of the screen. If you find them hard to read, set the On Screen Display to

Position - Wide.

If you prefer not to have the operation displays (

Play, Stop, Resume, etc.) shown on-screen, change the

On

Screen Display setting to Off.

Audio Video Language General

TV Screen 16:9(Wide)

Picture Quality

Still Picture

On Screen Display

Standard

Field

Position – Wide

Off

Move

Setup

Exit

34

En

Video settings

TV Screen Size

• Set in Setup Navigator (Default: 16:9 (Wide))

If you have a widescreen TV, select the

16:9 (Wide)

setting—widescreen DVD software is then shown using the full screen area. When playing software recorded in conventional (4:3) format, the settings on your TV will determine how the material is presented—see the manual that came with your TV for details on what options are available.

If you have a conventional TV, choose either

4:3 (Letter

Box) or 4:3 (Pan & Scan). In Letter Box mode, widescreen software is shown with black bars at the top and bottom of the screen. Pan & Scan chops the sides off widescreen material to make it fit the 4:3 screen (so even though the picture looks larger on the screen, you’re actually seeing less of the movie). See Aspect ratio in the Glossary on page 58 for more information.

Audio Video Language General

TV Screen 4:3(Letter Box)

Picture Quality –

4:3(Pan&Scan)

16:9(Wide)

Select your display preference

Move

SETUP

Exit

Adjusting the video quality

There are several preset picture quality settings that suit various program types. Alternatively, set up your own and save them for later recall.

Audio Video Language General

TV Screen – 16:9(Wide)

Picture Quality

Cinema

Animation

Standard

Adjust picture quality

Move

SETUP

Exit

9 DVD Settings

Still Picture

(Expert)

• Default setting:

Auto

This system uses one of two processes when displaying a still frame from a DVD disc. The default Auto setting lets the system decide which to use.

Field – produces a stable, generally shake-free image.

Frame – produces a sharper image, but more prone to shake than field stills.

Audio Video Language General

TV Screen

Picture Quality

Still Picture

On Screen Display

16:9(Wide)

Standard

Field

Frame

Move

Setup

Exit

Angle Indicator

(Expert)

• Default setting:

On

If you prefer not to see the camera icon on-screen during multi-angle scenes on DVD discs, change the

Angle

Indicator setting to Off.

Audio Video Language General

TV Screen

Picture Quality

Still Picture

On Screen Display

Angle Indicator

16:9(Wide)

Standard

Field

Position – Normal

On

Off

Move

Setup

Exit

35

En

9 DVD Settings

Audio settings

Dolby Digital Out

• Set in Setup Navigator (Default: Dolby Digital)

You only need to make this setting if you connected this system to another component (MD recorder, etc.) using one of the digital outs.

When recording a Dolby Digital disc to an MD or CD recorder, set this to

Dolby Digital

3 PCM. When you're done recording, set it back to Dolby Digital for proper playback of Dolby Digital discs.

Audio Video Language General

Dolby Digital Out Dolby Digital

96kHz PCM Out – Dolby Digital

3

PCM

Change Dolby Digital output mode

Move

SETUP

Exit

Linear PCM Out

• Set in Setup Navigator (Default: 96kHz)

You only need to make this setting if you connected this system to another component (MD recorder, etc.) using one of the digital outs.

When recording a 96kHz/24-bit disc to an MD or CD recorder, set this to

96kHz

3 48kHz. When you're done recording, set it back to 96kHz for proper playback of 96kHz/24-bit discs.

Audio

Video

Language General

Dolby Digital Out –

Dolby Digital

96kHz

3

48kHz

96kHz

Chenge 96 kHz output mode

Move

SETUP

Exit

Language settings

Audio Language

• Default Setting:

English

This setting is your preferred audio language for DVD discs. If the language you specify here is recorded on a disc, the system automatically plays the disc in that language (although this depends on the Auto Language setting—see Auto Language on page 37).

Audio

Video

Language General

OSD Language – English

Setup audio language

Other

Move

SETUP

Exit

The DVD format recognizes 136 different languages. Choose

Other if you want to specify a language other than those listed, then follow the on-screen display to select a language.

You may also want to refer to the DVD language code list on page 59.

Audio Video Language

Audio Language

List of Languages

General

Code (0~2) ja: Japanese

1 0 0 1

Setup audio language

Move

+/–

ENTER

Select

RETURN

Return

SETUP

Exit

Remember: You can switch between the languages recorded on a DVD disc any time during playback using the

AUDIO button. (This does not affect this setting.)

36

En

Subtitle Language

• Default Setting:

English

This setting is your preferred subtitle language for DVD discs.

If the language you specify here is recorded on a disc, the system automatically plays the disc with those subtitles

(although this depends on the Auto Language setting—see

Auto Language on the right).

Audio Video Language General

OSD Language – English

Other

Setup disc's subtitle language

Move

SETUP

Exit

The DVD format recognizes 136 different languages. Choose

Other if you want to specify a language other than those listed, then follow the on-screen display to select a language.

You may also want to refer to the DVD language code list on page 59.

Audio Video Language

Subtitle Language

List of Languages

General

Code (0~2) ja: Japanese

1 0 0 1

Setup disc's subtitle language

Move

+/–

ENTER

Select

RETURN

Return

SETUP

Exit

Remember: You can change or switch off the subtitles on a DVD disc any time during playback using the

SUBTITLE

button. (This does not affect this setting.)

9 DVD Settings

Auto Language

• Default Setting:

On

When set to On, the system always selects the default audio language on a DVD disc (French dialog for a French movie, for example), and displays subtitles in your preferred subtitle language only if that is set to something different. In other words, movies in your native language won’t have any subtitles, while foreign language movies will be shown with subtitles.

Set to Off to have the system play discs strictly according to your Audio Language and Subtitle Language settings.

For Auto Language to work, the Audio Language and Subtitle

Language settings must be the same—see pages 36–37.

Audio Video Language General

OSD Language – English

Audio Language – English

Subtitle Language – Spanish

Off

Play dialog, etc. in original language

Subtitles ON with foreign audio

Move

SETUP

Exit

Remember: You can still switch audio and subtitle languages on playback using the

AUDIO

and

SUBTITLE

buttons.

37

En

9 DVD Settings

DVD Language

(Expert)

• Default Setting:

w/Subtitle Language

Some multi-lingual discs have disc menus in several languages. This setting specifies in which language the disc menus should appear. Leave on the default setting for menus to appear in the same langauge as your subtitle preference— see page 37.

Audio Video Language General

OSD Language – English

Audio Language – English

Subtitle Off

(Expert)

• Default Setting:

Selected Subtitle

Some discs display subtitles even if the Subtitle Display setting (below) is set to off. In this case, you can either have the subtitles displayed in the same language as your preferred audio language ( With Audio), or in your preferred subtitle language ( Selected Subtitle). If the Audio Langage and Subtitle Language settings are the same then both of these choices will give the same result.

Audio Video Language General

OSD Language – English

Audio Language – English

Subtitle Language – Spanish

Auto Language – On

DVD Language – English

Move

SETUP

Exit

Move

SETUP

Exit

The DVD format recognizes 136 different languages. Choose

Other if you want to specify a language other than those listed, then follow the on-screen display to select a language.

You may also want to refer to the DVD language code list on page 59.

Audio Video Language

DVD Language

List of Languages

General

Code (0~2) ja: Japanese

1 0 0 1

Move

+/–

ENTER

Select

RETURN

Return

SETUP

Exit

Subtitle Display

(Expert)

• Default Setting:

On

Set to On, the system displays subtitles according to the

Subtitle Language and Auto Language settings above. Set to

Off to switch subtitles off altogether (although see Subtitle

Off above). Set to Assist Subtitle to have the system display the extra assistive subtitles recorded on to some DVD discs.

Audio Video Language General

OSD Language – English

Audio Language – English

Subtitle Language – Spanish

Auto Language – On

Move

SETUP

Exit

38

En

9 DVD Settings

Miscellaneous settings

Parental Lock

• Default level:

8

• Default password:

none

You can restrict access to certain discs using this feature. Once set, you will be asked for a four-digit password when a restricted disc is loaded, giving you a degree of control over what your children watch.

You can set the restriction to one of eight levels. Setting the level at 1 means that any disc that has any level of restriction will need the password in order to watch it, while setting it at level 8 gives unlimited access.

DVD discs are also rated from 1 to 8. Discs rated 1 (or with no rating) generally contain little or no offensive material; discs rated 2, may contain material that some parents may feel is unsuitable for children. Discs rated 8 will almost certainly be unsuitable for children.

Since a disc’s rating is up to the manufacturer, it is not possible to give a definitive guide to each level—check the disc box for parental lock details.

Be careful: not all discs that you may consider inappropriate for your children are rated. Unrated discs will always play without requiring the password first.

Changing the parental lock level

1 Select Level Change.

Audio Video Language General

Parental Lock: Register Code Number

Enter 4–Digit Code

Move

RETURN

Return

SETUP

Exit

2 Use the number buttons to register a new password or confirm your existing password, then press ENTER.

The first time you set the parental lock level, you have to register a password. Anything you input becomes your password.

Audio

Video

Language General

Parental Lock: Register Code Number

1 0 1 9

ENTER

Enter 4–Digit Code

Move

+/–

RETURN

Return

SETUP

Exit

Audio Video Language General

Setup Menu Mode – Basic

Setup Navigator

Parental Lock Level Change

Password Change

Setup viewing restrictions

Move

SETUP

Exit

3 Select a new level.

Move leftward to lock more levels (more discs will require the password); rightward to unlock levels. You can’t lock level 1.

Audio Video Language General

Parental Lock: Level Change

Level 1 2 3 4

Set Parental Lock

5 6 7 8

Move

ENTER

Select

RETURN

Return

SETUP

Exit

4 Press ENTER to set the new level.

The screen returns to the General menu display.

39

En

9 DVD Settings

Changing your password

1 Select Password Change.

Audio Video Language General

Parental Lock: Confirm Code Number

Enter 4–Digit Code

Move

RETURN

Return

SETUP

Exit

2 Input your existing password, then press

ENTER.

Audio

Video

Language General

Parental Lock: Confirm Code Number

ENTER

Enter 4–Digit Code

Move

+/–

RETURN

Return

SETUP

Exit

3 Input a new password, then press ENTER.

The new password is set and the screen returns to the General menu display.

Audio

Video

Language General

Parental Lock: Password Change

6 2 7 1

ENTER

Enter 4–Digit Code

Move

+/– RETURN

Return

SETUP

Exit

If you forget your password, resetting the system will clear the password. See page 66 for more on this.

Background Color

(Expert)

• Default setting:

Blue

This specifies the color of the screen when there’s no video.

Audio Video Language General

Setup Menu Mode — Expert

Setup Navigator

Parental Lock — Level 8

Background Color

Black

Blue

Other

Move

SETUP

Exit

40

En

10 Advanced Sound Setup

Advanced sound settings

This chapter covers advanced settings to further optimize the sound of your system.

LFE attenuator

The LFE (low frequency effects) channel carries ultra low bass sound to add weight to effects in Dolby Digital and DTS soundtracks. This channel can overload the sub-woofer resulting in distortion. Use the LFE attenuator setting to reduce the signal fed to the subwoofer.

Note: The LFE attenuator only works with sources that contain an LFE channel. It is not a general level control for the sub-woofer.

1 Press SYS then SETUP.

2 Press the

@ or # button until you see LFE ATT in the display.

3 Use the

% and fi buttons to set the amount of signal reduction.

There are three settings:

ATT 0 – default setting (no signal reduction)

ATT 10 – the LFE channel signal level is reduced to avoid distortion

OFF – the LFE channel is switched off completely. This may be useful late at night, for example.

4 Press ENTER to make the setting.

Dynamic Range Control

The dynamic range of a source is the difference between the quietest and the loudest sounds. The dynamic range of Dolby Digital soundtracks can be very great. This makes them exciting, but it also means that when you turn the volume down you can easily lose quiet dialog. Switch on Dynamic Range Control to even out the soundtrack volume.

1 Press SYS then SETUP.

2 Press the

@ or # button until you see D.R.C. in the display.

3 Use the

% and fi buttons to sselect a dynamic range setting.

D.R.C. OFF – default setting (no change to the dynamics)

D.R.C. LOW – the dynamic range is reduced by a small amount.

D.R.C. MEDIUM – mid setting

D.R.C. HIGH – the dynamic range is reduced by a large amount (good for listening at very low volume).

4 Press ENTER to make the setting.

41

En

10 Advanced Sound Setup

Dual-mono setting

The dual-mono setting applies only to Dolby Digital discs that feature dual-mono material—see the disc box for details.

Dual-mono discs are recorded with two independent channels that may be played together or separately depending on the situation. For example, a guitar tuition disc might have the guitar recorded on one channel and all the other instruments on the other. Use the dual-mono setting to play just the guitar part on its own; just the backing, or everything together (through separate speakers, or mixed).

1 Press SYS then SETUP.

2 Press the

@ or # button until you see STEREO or DUAL MONO

in the display.

3 Use the

% and fi buttons to select a dual-mono setting.

STEREO – default setting (Ch1 is played through the left speaker; Ch2 through the right)

DualMono Ch1 – Ch1 is played through the center speaker (or through the left and right speakers if Surround Off is selected); Ch2 is muted.

DualMono Ch2 – Ch2 is played through the center speaker (or through the left and right speakers if Surround Off is selected); Ch1 is muted.

DualMono MIX – Ch1 and Ch2 are mixed together and played through the center speaker (or through both left and right speakers if Surround Off is selected).

4 Press ENTER to make the setting.

42

En

11 Controlling Other Equipment

Setting up the remote control

In addition to controlling this system, you can set up the remote to operate other audio/ visual components, such as your TV, VCR, MD recorder, and so on.

To set up the remote, often all you need to do is to tell it what component(s) you have

(see Setting up using component presets below). If you have a component that the remote doesn’t know how to control already, you can ‘teach’ it using that component’s remote control (see Learning directly from other remote controls on page 45).

Setting up using component presets

This method of setting up the remote requires only that you tell it the manufacturer of each component. You do this by looking up the type of component (TV, MD deck, etc.), and the manufacturer in the Preset code list starting on page 60.

After setting up, see pages 48 – 52 for how to actually control your other components using this remote.

Note: The correct preset code may not cover all the remote control commands for your particular components. Use the learning function to program extra commands

(see Learning directly from other remote controls on page 45).

1 Switch on the component you are setting up this remote for.

After you’ve entered the correct code in the steps below, the remote should switch off the component.

2 Press and hold REMOTE SETUP for three seconds.

The red LED at the top of the remote blinks twice.

• To cancel, press

REMOTE SETUP

again.

3 Press the MULTI CONTROL button for the component you want to control.

For example, if you want to set up the remote to control your TV, press

TV

.

The

MULTI CONTROL

buttons have different types of components assigned to them by default:

V-1 – analog or digital VCR, DVD,

DVD-R, LD, DVD/LD player (default: Pioneer VCR, 0058).

V-2 – Satellite, cable or DTV tuner (default: Pioneer cable TV tuner, 0533).

A-1 and A-2 – CD player, CD-R recorder, tape deck, MD deck (A-1 default:

Pioneer CD-R recorder, 1087. A-2 default: Pioneer CD player, 0032).

TV – television (default: Pioneer TV, 0679).

You can change these assignments if you need to. For example, if you connected an audio component to one of the video inputs/outputs. See page 44 for how to do this.

4 Look up the preset code for your component.

You can find this in Preset code list starting on page 60. First find the type of component (TV, etc.), then find the manufacturer. Next to each manufacturer is one or more 4-digit codes.

• If you can’t find the manufacturer of your component in the code list, press

REMOTE SETUP

to exit, then see Learning directly from other remote controls on page 45 for how to set up the remote using an alternative method.

• If no button is pressed for more than 10 seconds, remote setup is exited.

43

En

11 Controlling Other Equipment

5 Point the remote at the component to control and enter the

4-digit code.

If there’s more than one code, enter the first one.

The LED blinks after each button press, and twice to confirm a valid code has been input. If it doesn’t blink twice, you have entered an invalid code: check the code and input it again.

If all went well, the remote should have just switched off the other component. If it didn’t, and the manufacturer has more than one code in the list, start again from step 1 using another code.

Reassigning a MULTI CONTROL button

You can only assign preset codes for certain kinds of components to each

MULTI

CONTROL

button. However, if necessary, you can reassign a

MULTI CONTROL

button to a different kind of component. You would need to do this if you connected an

MD recorder to the Video 1 inputs/outputs, for example.

1 Press and hold REMOTE SETUP for three seconds.

The LED at the top of the remote will blink twice.

2 Press the MULTI CONTROL button which you want to change.

You can reassign these buttons:

V-1

V-2

A-1

A-2

TV

In the above example, press V-1.

3 Use the number buttons to enter 992.

4 Press the MULTI CONTROL button which you want duplicated.

In the above example, press A-1.

44

En

11 Controlling Other Equipment

Learning directly from other remote controls

If preset codes are not available for your component(s), or the available preset codes do not work, you can use this method to teach the remote each command separately.

You can also use this operation to program additional commands for a component not covered in the preset codes.

1 Press and hold REMOTE SETUP for three seconds.

The LED at the top of the remote blinks twice.

2 Press the MULTI CONTROL button for the component you want to control.

For example, press VIDEO V-1 to program a command from a VCR connected to the

Video 1 inputs/outputs.

3 Using the number buttons, enter 975.

The LED flashes rapidly to indicate that the remote is in Learning Setup mode and ready to learn new commands from another remote.

• The remote will exit Learning Setup after 10 seconds if no commands are entered.

• To cancel Learning Setup here, press

REMOTE SETUP

.

4 Press the MULTI CONTROL button again for the component you want to control.

5 Press the button on this system’s remote that you want to learn a new command.

For example, press

3.

The illustration left shows the buttons that can be used to learn commands.

6 Point the remotes towards each other, about 2-5 cm (1-2 inches) apart.

7 Press the button on the other component’s remote for the command you want to program.

The LED on this system’s remote will go out and then blink twice when the command has been learned.

• If the LED doesn’t start blinking, try varying the distance between the remotes, then press the button again.

• Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.

• If the LED starts to blink slowly, it may mean that no more commands can be learnt.

If it is necessary to learn another command, first delete another learnt command— see the following page.

8 Program additional commands for the same component as required.

Repeat steps 5 through 7.

9 Program commands for other components as required.

Repeat steps 4 through 7.

10 When you’re done, press REMOTE SETUP to exit Learning Setup mode.

45

En

11 Controlling Other Equipment

Deleting a single command

1 Press and hold REMOTE SETUP for three seconds.

2 Press the MULTI CONTROL button related to the command you want to delete.

For example, press

VIDEO V

-

1

if the command you want to delete is one for a VCR connected to the Video 1 inputs.

3 Use the number buttons to enter 976.

4 Press the same MULTI CONTROL button again.

In the above example, press

VIDEO V

-

1

again.

5 Press twice the command button you want to delete.

Deleting all commands for a component

1 Press and hold REMOTE SETUP for three seconds.

2 Press the MULTI CONTROL button related to the commands you want to delete.

For example, press

VIDEO V

-

1

if the commands you want to delete are for a VCR connected to the Video 1 inputs.

3 Use the number buttons to enter 976.

4 Press the same MULTI CONTROL button twice more.

In the above example, press

VIDEO V

-

1

twice.

Controlling a component while playing another

This feature allows you to keep the system in one function (for example, CD) while putting the remote control in a different one (Video 1, for example). This may be useful if you were listening to a CD and wanted to rewind a video tape, for example.

1 Press SHIFT, then press the MULTI CONTROL button for the component you want to control.

The system remains in the same function, but the remote is in a different one.

2 To switch back to the original function, press the MULTI

CONTROL for the current system function.

It’s also possible to set up the remote so that a particular multi control button always

only switches the remote control mode and not the system function.

1 Press and hold REMOTE SETUP for three seconds.

The LED at the top of the remote blinks twice.

2 Press the MULTI CONTROL button you want to set up.

3 Use the number buttons to enter 983.

The LED on the top of the remote blinks twice. Now, when you press that

MULTI

CONTROL

button, only the remote mode changes.

• To change the button back, repeat the above, entering 982 in step 3.

46

En

11 Controlling Other Equipment

Clearing all remote control settings

This clears all presets, all learnt functions and restores the factory presets.

1 Press and hold REMOTE SETUP for three seconds.

The LED at top of the remote blinks twice.

2 Press any MULTI CONTROL button.

3 Use the number buttons to enter 981.

The LED blinks a total of four times to indicate the button has been cleared.

Checking preset codes

To check which preset code is associated with a

MULTI CONTROL

button:

1 Press and hold REMOTE SETUP for three seconds.

The LED at top of the remote will blink twice.

2 Press the MULTI CONTROL button you want to check the preset code for.

3 Use the number buttons to enter 990.

Each preset code consists of four digits, for example 1329. Each digit will be represented by a series of blinks on the remote’s LED—3 blinks to represent the digit “3”, etc.

4 Press 1.

The blinking LED indicates the left-most digit of the preset code (“1” in the example above).

5 Press 2.

The blinking LED indicates the next digit of the preset code (“3” in the example above).

6 Press 3.

The blinking LED indicates the next digit of the preset code (“2” in the example above).

7 Press 4.

The blinking LED indicates the right-most digit of the preset code (“9” in the example above).

47

En

11 Controlling Other Equipment

CD/MD/CD-R/VCR/LD player controls

These controls are available after you set up the remote to control. See Setting up the remote

control on page 43 for how to do this.

1

10

16

12

15

17

14

11

8

9

23

22

19

7

2

20

13

4

18

3

5

6

21

1 SOURCE

Press to switch between standby and on.

2

4

Press to return to the start of the current track. Repeated presses skips to the start of previous tracks.

3

¢

Press to advance to the start of the next track. Repeated presses skips to the start of following tracks.

4

8

Press to pause playback.

5

¡

Hold down for fast playback.

6

1

Hold down for fast reverse playback.

7

3

Press to start playback.

8

7

Press to stop playback.

9

Press twice within 10 seconds to start recording or pause recording.

10

2

Press to rewind or reverse program source.

11

3

Press to fast forward program source.

12

5

Press to pause program source.

13

Press to stop program source.

14 ENTER

to play program source.

15 Number buttons

Used to directly access tracks on a program source.

16 >10

Use to select track numbers over 10.

17 ENTER/DISC, C

Function varies with the component:

CD changer : selects a disc

CD-R, MD, LD : clear function

VCR : enter function

18 DISP

Press to switch the display.

19 PGM

Press to start program play.

20 RDM

Press to start random play.

21 REPEAT

Press to start repeat play.

22 CH –

Press to change the TV channel on the

VCR.

23 CH +

Press to change the TV channel on the

VCR.

48

En

1

12

14

10

8

9

7

2

6

13

11

4

3

5

11 Controlling Other Equipment

Cassette deck controls

These controls are available after you set up the remote to control. See Setting up the remote

control on page 43 for how to do this.

1 SOURCE

Press to switch between standby and on

(not possible on all models).

2

4

Use to play the reverse side of the tape on a reversible deck.

3

¢

Use to play the forward side of the tape on a reversible deck.

4

8

Press to pause playback or recording.

5

¡

Press to fast forward the tape. Pressing during playback starts forward search.

6

1

Press to rewind the tape. Pressing during playback starts reverse search.

7

3

Press to start playback.

8

7

Press to stop playback.

For deck two or any tape deck that can record:

9

Press twice within 10 seconds to start recording or pause recording.

For deck one of a dual tape deck:

10

2

Press to rewind the tape.

11

3

Press to fast forward the tape.

12

5

Press to pause the tape.

13

Press to stop the tape.

14 ENTER

Press to start playback.

49

En

11 Controlling Other Equipment

1

3

5

2

4

22

6

11

13

12

9

7

16 17

18

20 21

8

10

14

15

19

DVD/DVR player controls

These controls are available after you set up the remote to control. See Setting up the remote

control on page 43 for how to do this.

1 SOURCE

Press to switch the DVD or DVR between standby and on.

2 Number buttons

Press to directly access tracks.

3 >10

Use to select track numbers over 10.

4 C

Use to clear function.

5

5//2/3/ENTER

Use to navigate items on the menu screen.

6

7

Press to stop playback or recording.

7

3

Press to start playback.

8

8

Press to pause playback or recording.

9

4

Press to return to the start of the current track. Repeated presses skip to the start of previous tracks.

10

¢

Press to advance to the start of the next track. Repeated presses skip to the start of following tracks.

11 RETURN /

DVD : Use to go back one menu.

DVR : Press twice within 10 seconds to start recording.

12

e/CH–

Press during playback for reverse slow motion. When paused, press to go back frame-by-frame. For DVR, use to change channels.

13

E/CH+

Press during playback for slow motion.

When paused, press to advance frame-byframe. For DVR, use to change channels.

14

1

Press and hold for fast reverse scanning.

15

¡

Press and hold for fast forward scanning.

16 TOP MENU/PGM

Press to display the top menu of a DVD disc. Press with

SHIFT

to program a playlist of tracks.

17 SUBTITLE/RDM

Press to display/switch subtitles. Press with

SHIFT

to start random playback.

18 AUDIO/DISPLAY

Press to select the audio language. Press with

SHIFT

to display/switch disc information.

19 LAST MEMORY/

Press to set a bookmark, or start playback from a bookmarked disc. Press with

SHIFT

to switch camera angles.

20 REPEAT/CONDITION

Press once to repeat playback of the current track, or twice to repeat playback of the current title. Press with

SHIFT

to save the player settings for the currently loaded disc.

21 A-B /SEARCH MODE

Press once to mark the start of a loop; press again to mark the end and start looping.

Press with

SHIFT

to select the disc search mode.

22 SETUP

Press to access the Setup menu.

50

En

3

16

14

1

2

17

15

5

4

6

24

23

22

7

9

18 19 20 21

13

8

10

12

11

11 Controlling Other Equipment

DTV controls

These controls are available after you set up the remote to control. See Setting up the remote

control on page 43 for how to do this.

1 SOURCE

Press to switch the TV on or off.

2 Number buttons

Use to select a specific TV channel.

3 >10 ( • )

Use to add a decimal point when selecting a specific TV channel.

4 ENTER/DISC

Use to enter a channel.

5

5˜∞˜2˜3˜ENTER

Press to select or adjust and navigate items on the menu screen.

ENTER

Use to bring up the DTV menus.

6

7 (CLOSED CAPTION)

Press to display closed captions

7

3 (AUDIO)

Press to select audio channels

8

8 (SCREEN MODE)

Press to select the screen mode.

9

4 (DTV)

Press to switch the DTV on/off

10

¢ (MENU)

Use to display the menu.

11

¡ (GUIDE)

Use as the Guide button for navigation.

12

1 (CLEAR)

Press to clear the DTV menu.

13 MENU

Use to select different menus from the DTV functions.

These four buttons are dedicated TV control buttons.

14 TV

Press to switch the TV between standby and on.

15 TV INPUT

Press to switch the TV input (not possible with some models).

16 TV CHANNEL +/–

Use to select channels.

17 TV VOL +/–

Use to adjust the TV volume.

18 TOP MENU (BLUE)

Use to choose the blue commands on a

DTV menu.

19 SUBTITLE (GREEN)

Use to choose the green commands on a

DTV menu.

20 AUDIO (RED)

Use to choose the red commands on a DTV menu.

21 LAST MEMORY (YELLOW)

Use to choose the yellow commands on a

DTV menu.

22 CH –

Press to change the DTV channel.

23 CH +

Press to change the DTV channel.

24 RETURN /

(Information)

Press to get INFO on the DTV program.

51

En

11 Controlling Other Equipment

Cable TV/satellite TV/TV controls

These controls are available after you set up the remote to control. See Setting up the remote

control on page 43 for how to do this.

9

3

1

12

11

8

4

2

7

5

10

6

13

The first four buttons are dedicated TV control buttons.

1 TV

Press to switch the TV between standby and on.

2 TV INPUT

Press to switch the TV input (not possible with some models).

3 TV CHANNEL +/–

Use to select channels.

4 TV VOL +/–

Use to adjust the TV volume.

5 PAGE –

Press to display the previous menu page on cable TV.

6 PAGE +

Press to display the next menu page on cable TV.

7

5˜∞˜2˜3˜ENTER

Press to select or adjust and navigate items on the menu screen.

8 Number buttons

Use to select a specific TV channel.

9 SOURCE

Press to switch the TV or CATV between standby and on.

10 MENU

Press to display or close the TV or CATV menu.

11 RETURN (INFO)

Press to display information on cable TV.

12 EXIT

Press to exit.

13 GUIDE

Press to switch the program information screen for cable TV on/off.

52

En

Connecting to a TV with the supplied video cord

Important: Before making or changing any rear panel connections, switch off the power and disconnect the power cord from the AC outlet.

You can connect this system to any TV using this output jack with the supplied video cord. However, if your TV has an

S-Video input, we recommend also using that since you should get a better picture.

Refer to the TV’s instruction manual for more detailed connection instructions.

Playing your TV through this system

12 Connecting Up

When watching cable or satellite TV, it’s best to connect the cable/satellite box directly to this system, rather than going via the TV. However, if you’re watching TV via an antenna plugged directly into the back of the TV, then connect your

TV’s audio outputs to the

AUDIO

1

or

AUDIO

2

inputs of this system to play the TV’s audio through the speakers of this system. Use a standard stereo audio cord (not supplied), matching up the colors both ends for best results.

Connect to AUDIO 1 IN or AUDIO 2 IN

TV

Yellow

TV

Yellow

Connecting to a TV with an

S-Video cord

Many TVs also have an S-Video input which you can use to connect to this system using an S-Video cord (not supplied).

Refer to the TV’s instruction manual for more detailed connection instructions.

White Red

White

Red

Watching TV

With the above connections made, your TV becomes another source component for this system.

To play your TV through this system, press the

AUDIO A-1 or A-2 button (depending on which one the TV is connected to).

If the TV is connected to

AUDIO 1

, memorize its remote control codes in the

AUDIO A

1

multi control button. If it is connected to

AUDIO

2

, memorize its remote control codes in the

AUDIO A

2

multi control button. See chapter 11 for more on this.

TV

53

En

12 Connecting Up

Connecting Other

Components

• Connect an audio/visual player or recorder, such as a video recorder or satellite decoder to the

VIDEO

1

inputs/ outputs.

• Connect an audio/visual player, such as a video deck or satellite decoder to the

VIDEO

2

inputs. If the player has a digital audio output, connect to the

VIDEO 2 DIGITAL

IN

or

OPTICAL IN

jacks.

See Switching between digital and analog sources on page 19 for more on this.

• Connect an audio player/recorder, such as an MD deck, to the

AUDIO

1

analog inputs/outputs. If the player/ recorder has optical digital jacks, connect to the

AUDIO

1

OPTICAL IN

to the player/recorder’s optical output, and

AUDIO

1

OPTICAL OUT

to the player/recorder’s optical input.

See Switching between digital and analog sources on page 19 for more on this.

• Connect an audio player to the

AUDIO

2

analog inputs.

Important: if you connect a video component with a standard video cord, your TV must also be connected to this system with a standard video cord.

To the TV’s video input

From an auxiliary component’s video output jacks

To an auxiliary component’s video input jacks

Connecting an audio recorder

Analog inputs are only output from the analog outputs. (You can’t record an analog input via the digital output.) Likewise, you can’t record a digital input via the analog outputs.

LD player, video deck, etc.

(Components with audio/ video capability)

Tape deck, etc.

(Audio only components)

For digital connection

Important: if you connect a video component with an S-

Video cord, your TV must also be connected to this unit with an S-Video cord.

To an auxiliary component’s audio input jacks

No output

From an auxiliary component’s audio output jacks

No output No output

To the TV’s

S-Video input

From an auxiliary component’s S-Video output jacks

To an auxiliary component’s

S-Video input jacks

From an auxiliary component’s audio output jacks

54

En

12 Connecting Up

Connecting outdoor antennas

If reception is poor with the supplied antenna, connect a commercially available outdoor AM and/or FM antenna.

Connecting an outdoor AM Antenna

Connect as shown in the figure below. Do not disconnect the AM loop antenna even if you connect an outdoor AM antenna.

Outdoor AM antenna

Indoor AM antenna

Vinyl insulated wire (5 to 6m)(15–18ft.)

The system’s antenna terminal

AM loop antenna

Connecting an outdoor FM Antenna

Connect as shown in the figure below.

75

coaxial cable (3C-2V)

Unit: mm

FM antenna

Tooled(–)

Insulated(+)

The system’s antenna terminal

Note: The ground mark ( ) on the antenna terminal refers to measures to reduce reception noise when an antenna is connected. It does not refer to a safety ground.

55

En

13 Additional Information

Setting the display brightness

You can adjust the brightness of the display to suit the lighting conditions of the room.

For example, in a brightly lit room you'd probably want the display brighter than in a room with low lighting.

• Press SYS then FL DIMMER.

Press

FL DIMMER

repeatedly to set the display brightness. There are five levels.

Switching the TV system output

DVD and Video CD discs are recorded in either PAL or NTSC format. This setting determines which TV signal format is output to your TV.

1 With the system in standby, press SYS then SETUP.

2 Press the

@ or # button until you see

DVD VIDEO in the display.

3 Use the

% and fi buttons to select a video out setting.

DVD VIDEO AUTO

– default setting (video is output according to the disc loaded:

PAL if it's a PAL disc; NTSC if it's an NTSC disc). If you have a multi-system TV, leave this setting as

AUTO

.

DVD VIDEO PAL

– output is always PAL, even when an NTSC disc is loaded. Use this setting if your TV is PAL-compatible only.

DVD VIDEO NTSC

– PAL Video CDs are output as NTSC; PAL DVD discs cannot be played on this setting. Use this setting if your TV is NTSC-compatible only.

4 Press ENTER to make the setting.

56

En

13 Additional Information

Taking care of your system

To clean this unit, wipe with a soft, dry cloth. For stubborn dirt, wet a soft cloth with a mild detergent solution made by diluting one part detergent to 5 or 6 parts water, wring well, then wipe off the dirt. Use a dry cloth to wipe the surface dry.

Do not use volatile liquids such as benzene and thinner which may damage the surfaces.

• Wipe lightly from the center of the disc using straight strokes.

Disc lens cleaner

The disc pickup lens should not become dirty in normal use, but if for some reason it should malfunction due to dirt or dust, consult your nearest Pioneer authorized service center.

Although lens cleaners for CD players are commercially available, we do not recommend using them since some may damage the lens.

• Don’t wipe the disc surface using circular strokes.

Taking care of your discs

When holding discs, take care not to leave fingerprints, dirt or scratches on the disc surface. Hold the disc by its edge or by the center hole and edge. Damaged or dirty discs can affect playback performance. Take care also not to scratch the label side of the disc. Although not as fragile as the recorded side, scratches can still result in a disc becoming unusable.

Storing discs

Although CDs and DVDs are more durable than vinyl records, you should still take care to handle and store discs correctly.

When you're not using a disc, return it to its case and store upright. Avoid leaving discs in excessively cold, humid, or hot environments (including under direct sunlight).

Don't glue paper or put stickers on discs, or write on them using a pencil, ball-point pen or other sharp-tipped writing instrument.

Should a disc become marked with fingerprints, dust, etc., clean using a soft, dry cloth, wiping the disc lightly from the center to the outside edge as shown on the right. If necessary, use a cloth soaked in alcohol, or a commercially available CD or DVD cleaning kit to clean a disc more thoroughly. Never use benzine, thinner or other cleaning agents, including products designed for cleaning vinyl records.

Discs to avoid

Discs spin at high speed during playback. If you can see that a disc is cracked, chipped, warped, or otherwise damaged, don't risk using it—you could end up damaging the system.

This system is designed for use with conventional, fully circular discs only. Use of shaped discs is not recommended.

Pioneer disclaims all liability arising in connection with the use of shaped CDs and DVDs.

57

En

13 Additional Information

Glossary

Analog audio

An electrical signal that directly represents sound. Compare this to digital audio which can be an electrical signal, but is an indirect representation of sound. See also Digital audio.

Aspect ratio

The width of a TV screen relative to its height. Conventional

TVs are 4:3 (in other words, the screen is almost square); widescreen models are 16:9 (the screen is almost twice as wide as it is high).

Chapter

(DVD only)

Just as a book is split up into several chapters, a title on a DVD disc is usually divided into chapters. See also Title.

Digital audio

An indirect representation of sound by numbers. During recording, the sound is measured at discrete intervals (44,100 times a second for CD audio) by an analog-to-digital converter, generating a stream of numbers. On playback, a digital-to-analog converter generates an analog signal based on these numbers. See also Sampling frequency and Analog

audio.

Dolby Digital

A surround sound system developed by Dolby Laboratories containing up to six channels of digital audio (front left and right, surround left and right, center and low-frequency channels). See also DTS.

DTS

A surround sound system developed by Digital Theater

Systems as an alternative to Dolby Digital. DTS discs contain up to eight channels of digital audio. See also Dolby Digital.

Dynamic range

The difference between the quietest and loudest sounds possible in an audio signal (without distorting or getting lost in noise). Dolby Digital and DTS soundtracks are capable of a very wide dynamic range, delivering dramatic cinema-like effects.

MPEG video

The video format used for Video CDs and DVDs. Video CD uses the older MPEG-1 standard, while DVD uses the newer and much better quality MPEG-2 standard.

Optical digital output

A jack that outputs digital audio in the form of light pulses.

Connect components with optical digital jacks using a special optical cord, available from good audio dealers.

PCM (Pulse Code Modulation)

The most common system of encoding digital audio, found on CDs and DAT. Excellent quality, but requires a lot of data compared to formats such as Dolby Digital and MPEG audio.

For compatibility with digital audio recorders (CD, MD and

DAT) and AV amplifiers with digital inputs, this unit can convert Dolby Digital and MPEG audio to PCM. See also

Digital audio.

PBC (PlayBack Control)

(Video CD only)

A system of navigating a Video CD through on-screen menus recorded onto the disc. Especially good for discs that you would normally not watch from beginning to end all at once—karaoke discs, for example.

Regions

(DVD only)

These associate discs and players with particular areas of the world. This unit will only play discs that have compatible region codes. You can find the region code of your unit by looking on the rear panel. Some discs are compatible with more than one region (or all regions).

Sampling frequency

The rate at which sound is measured to be turned into digital audio data. The higher the rate, the better the sound quality, but the more digital information is generated. Standard CD audio has a sampling frequency of 44.1kHz, which means

44,100 samples (measurements) per second. See also Digital

audio.

Title

(DVD only)

A collection of chapters on a DVD disc. See also Chapter.

58

En

13 Additional Information

Bulgarian ( bg )

Bihari ( bh )

Bislama ( bi )

Bengali ( bn )

Tibetan ( bo )

Breton ( br )

Catalan ( ca )

Corsican ( co )

Czech ( cs )

Welsh ( cy )

Danish ( da )

Bhutani ( dz )

Esperanto ( eo )

Estonian ( et )

Basque ( eu )

Persian ( fa )

Finnish ( fi )

Fiji ( fj )

Faroese ( fo )

Frisian ( fy )

Irish ( ga )

Scots-Gaelic ( gd )

Galician ( gl )

Guarani ( gn )

Gujarati ( gu )

Language

Japanese/japonais ( ja )

English/anglais ( en )

French ( fr)

German ( de )

Italian ( it )

Spanish ( es )

Dutch ( nl )

Russian ( ru )

Chinese ( zh )

Korean ( ko )

Greek ( el )

Afar ( aa )

Abkhazian ( ab )

Afrikaans ( af )

Amharic ( am )

Arabic ( ar )

Assamese ( as )

Aymara ( ay )

Azerbaijani ( az )

Bashkir ( ba )

Byelorussian ( be )

DVD language code list

The table below lists all the languages and codes that are recognized by the DVD standard.

Language

Hausa ( ha )

Hindi ( hi )

Croatian (hr )

Hungarian ( hu )

Armenian ( hy )

Interlingua ( ia )

Interlingue ( ie )

Inupiak ( ik )

Indonesian ( in )

Icelandic ( is )

Hebrew ( iw )

Yiddish ( ji )

Javanese ( jw )

Georgian ( ka )

Kazakh ( kk )

Greenlandic ( kl )

Cambodian ( km )

Kannada ( kn )

Kashmiri ( ks )

Kurdish ( ku )

Kirghiz ( ky )

Latin ( la )

Lingala (ln )

Laothian ( lo )

Lithuanian ( lt )

Latvian ( lv )

Malagasy ( mg )

Maori ( mi )

Macedonian ( mk )

Malayalam ( ml )

Mongolian ( mn )

Moldavian ( mo )

Marathi ( mr )

Malay ( ms )

Maltese ( mt )

Burmese ( my )

Nauru ( na )

Nepali ( ne )

Norwegian ( no )

Occitan ( oc )

Oromo ( om )

Oriya ( or )

Panjabi ( pa )

Polish ( pl )

Pashto, Pushto ( ps )

Portuguese ( pt )

1222

1307

1309

1311

1312

1314

1315

1114

1119

1121

1125

1201

1214

1215

1220

0911

0914

0919

0923

1009

1023

Code

0801

0809

0818

0821

0825

0901

0905

1101

1111

1112

1113

1415

1503

1513

1518

1601

1612

1619

1620

1318

1319

1320

1325

1401

1405

0615

0625

0701

0704

0712

0714

0721

0515

0520

0521

0601

0609

0610

0301

0315

0319

0325

0401

0426

0207

0208

0209

0214

0215

0218

0118

0119

0125

0126

0201

0205

1115

0512

0101

0102

0106

0113

Code

1001

0514

0618

0405

0920

0519

1412

1821

2608

Language

Quechua ( qu )

Rhaeto-Romance ( rm )

Kirundi ( rn )

Romanian ( ro )

Kinyarwanda ( rw )

Sanskrit ( sa )

Sindhi ( sd )

Sangho ( sg )

Serbo-Croatian ( sh )

Singhalese ( si )

Slovak ( sk )

Slovenian ( sl )

Samoan ( sm )

Shona ( sn )

Somali ( so )

Albanian ( sq )

Serbian ( sr )

Siswati ( ss )

Sesotho ( st )

Sundanese ( su )

Swedish ( sv )

Swahili ( sw )

Tamil ( ta )

Telugu ( te )

Tajik ( tg )

Thai ( th )

Tigrinya ( ti )

Turkmen ( tk )

Tagalog ( tl )

Setswana ( tn )

Tonga ( to )

Turkish ( tr )

Tsonga ( ts )

Tatar ( tt )

Twi ( tw )

Ukrainian ( uk )

Urdu ( ur )

Uzbek ( uz )

Vietnamese ( vi )

Volapük ( vo )

Wolof ( wo )

Xhosa ( xh )

Yoruba ( yo )

Zulu ( zu )

1917

1918

1919

1920

1921

1922

1909

1911

1912

1913

1914

1915

Code

1721

1813

1814

1815

1823

1901

1904

1907

1908

2011

2012

2014

2015

2018

2019

2020

1923

2001

2005

2007

2008

2009

2023

2111

2118

2126

2209

2215

2315

2408

2515

2621

59

En

13 Additional Information

Preset Code List

DVD PLAYER/RECORDER

Manufacturer

Denon

GE

Harman/Kardon

JVC

Kenwood

Magnavox

Marantz

Mitsubishi

Onkyo

Optimus

Panasonic

Philips

Pioneer

Proscan

RCA

Samsung

Sharp

Sherwood

Sony

Technics

Theta Digital

Toshiba

Yamaha

Zenith

Code

0490, 0634

0522

0582

0558, 0623

0534

0503

0539

0521

0503, 0627

0571

0490, 0632

0503, 0539

0525, 0571, 0632,

0631(DVD-R)

0522

0522

0573

0630

0633

0533

0490

0571

0503

0490, 0545

0503, 0591

Quasar

Realistic

Rowa

SMC

Sega

Sharp

Shinco

Sony

Super

Technics

Toshiba

LASERDISC PLAYER

Manufacturer

Aiwa

Akai

Denon

Disco Vision

Funai

GoldStar

Hitachi

Hong Deng

Idall

Kebao

Mitsubishi

NAD

Optimus

Panasonic

Pioneer

Code

0203

0598

0059, 0172

0023

0203, 0584

0172

0023

0542

0595

0581

0059

0059

0059

0204, 0496

0023, 0059, 0463,

0572, 0548

0204

0203

0541

0596

0023

0597

0540

0193, 0201, 0583,

0589

0581

0204

0599

TELEVISION (1/4)

Manufacturer

A-Mark

AOC

Admiral

Aiko

Akai

Alaron

Ambassador

America Action

Ampro

Amstrad

Anam

Anam National

Archer

Audiovox

Baysonic

Belcor

Bell & Howell

Bradford

Brockwood

Broksonic

CCE

CXC

Candle

Carnivale

Carver

Celebrity

Cineral

Citizen

Concerto

Contec

Craig

Crosley

Crown

Curtis Mathes

Daewoo

Daytron

Denon

Dumont

Dwin

ECE

Electroband

Emerson

Envision

Etron

Fisher

Fortress

0092, 0451

0030, 0039, 0056,

0060, 0092, 0186,

1063

0056

0180

0161, 0180

0054

0039, 0180, 0418

0016, 0030, 0039,

0047, 0051, 0054,

0056, 0060, 0093,

0145, 0154, 0451,

0466, 1063, 1096,

1147, 1148, 1166,

1347

0019, 0039, 0066,

0092, 0154, 0451

0019

0145, 1148

0017, 0019

0720, 0774

0037

0000, 1003

0019, 0038, 0039,

0154, 0177, 0178,

0179, 0180, 0236,

0282, 0463, 1181

0030

0009, 0646

0154

0093, 1096

Code

0003

0003, 0019, 0030

0093, 0418, 0463,

1096

0092

0030, 0035

0179, 0216

0177

0180

0751

0412

0003, 0004, 0009,

0068, 0161, 0180,

0250, 0425, 1253

0161, 0250, 0425,

0650, 1253

0003

0003, 0092, 0180,

0451

0180

0019

0016, 0154

0180

0019

0003, 0236, 0463

0037

0180

0030, 0056, 0186

0030

0054, 0170

0000, 1003

TELEVISION (2/4)

Manufacturer

Fujitsu

Funai

Futuretech

GE

General

Gibralter

GoldStar

Gradiente

Grundig

Grunpy

Hallmark

Harley Davidson

Harman/Kardon

Harvard

HCM

Hitachi

Infinity

Innova

Inteq

JBL

JCB

JVC

KEC

KTV

Kamp

Kawasho

Kenwood

LG

LXI

Logik

Luxman

MGA

MTC

Magnavox

Majestic

Marantz

Matsushita

Megatron

Memorex

Midland

Minoka

Minutz

1056

0180

0030, 0039, 0180

0216

0216

0019, 0030

0056

0047, 0054, 0154,

0156, 0178, 1159,

1181

0016

0056

0019, 0030, 0150,

0178, 1153, 1181

0019, 0030, 0056,

0060, 0216, 1063

0030, 0036, 0054,

0179, 0186, 1254

0016

0030, 0037, 0054

0250, 0650, 1253

0003, 0145, 0178,

1148, 1181

0016, 0056, 0150,

0154, 0178, 0250,

0463, 1181, 1153,

1253

0017, 0039, 0047,

0051, 0135

0412

0021

Code

0179, 0683

0171, 0179, 0180,

0264, 1174

0180

0021, 0047, 0051,

0093, 0135, 0178,

0282, 0451, 1096,

1147, 1181, 1347

0186

0017, 0019, 0030

0001, 0002, 0019,

0030, 0037, 0039,

0056, 0178, 1181

0053, 0056, 0170,

1056

0037

0179, 0180

0178, 1181

0179

0054

0068, 0180

0412

0016, 0038, 0056,

0145, 0151, 1148

0054

0037

0017

0054

0000, 1003

0036, 0053, 0069,

0094, 0160, 0653,

60

En

TELEVISION (3/4)

Manufacturer

Mitsubishi

Motorola

Multitech

NAD

NEC

NTC

Netsat

Nicamagic

Nikko

Onwa

Optimus

Optonica

Orion

Osaki

Panasonic

Penney

Philco

Philips

Pilot

Pioneer

Portland

Prism

Proscan

Proton

Pulsar

Quasar

RCA

Radio Shack

Realistic

Rhapsody

Royal

Runco

SKY

SSS

Sampo

Samsung

Samsux

Sansei

Sansui

0037, 0054

0019, 0030, 0039

0038, 0172, 1166

0019, 0039, 0092

0051

0047

0003, 0178, 0466,

1181

0017, 0019

0051, 0165, 0250,

0650, 1253

0019, 0038, 0047,

0051, 0090, 0093,

0135, 1047, 1096,

1147, 1247, 1347,

1447

0019, 0030, 0039,

0047, 0056, 0154,

0165, 0178, 0180,

1181

0019, 0030, 0039,

0056, 0154, 0165,

0178, 0180, 1181

0216

0412

0017, 0030

0037

0019, 0180

0030, 0039

0019, 0030, 0037,

0056, 0060, 0090,

0178, 1063, 1181

0039

0451

0463

Code

0019, 0093, 0150,

0178, 1096, 1153,

1181, 0108, 0512

0093, 1096

0180

0156, 0178, 1159,

1166, 1181

0019, 0030, 0036,

0056, 0170

0092

0037

0216

0030, 0092, 0178,

1181

0180

0154, 0250, 0650,

1166, 1253

0093, 0165, 1096

0179, 0236, 0463

0412

0051, 0126, 0161,

0250, 0650, 1253

0002, 0003, 0019,

0021, 0030, 0039,

0047, 0051, 0056,

0060, 0135, 0156,

0178, 1063, 1159,

1181, 1347

0019, 0030, 0054,

0145, 0418, 0463,

1148

TELEVISION (4/4)

Manufacturer

Sanyo

Scimitsu

Scotch

Scott

Sears

Semivox

Semp

Sharp

Shogun

Signature

Simpson

Sky-Worth

Sony

Soundesign

Spectricon

Squareview

Starlite

SuperTech

Supreme

Sylvania

Symphonic

TMK

Tandy

Tatung

Technics

Technol Ace

Techwood

Teknika

Telefunken

Toshiba

Totevision

Vector Research

Victor

0003

0051, 0250, 1253

0179

0003, 0051, 0056

0016, 0019, 0039,

0054, 0056, 0060,

0092, 0150, 0179,

0180, 0186, 1063,

1153

0056

0036, 0060, 0154,

0156, 1063, 1159,

1256, 0035

0039

0030

0036, 0053, 0160,

Vidikron

Vidtech

Wards

0250, 0650, 1056,

1253

0054

0019, 0036, 0178,

1181

0016, 0019, 0021,

0030, 0054, 0056,

0165, 0178, 0179,

1181

White Westinghouse 0463

Yamaha

Zenith

0019, 0030

0016, 0017, 0092,

Zonda

0463

0003

Code

0154, 0208, 0339

0019

0178, 1181

0019, 0178, 0179,

0180, 0236, 1181

0047, 0054, 0056,

0154, 0156, 0171,

0178, 0179, 1159,

1174, 1181

0180

0156, 1159

0039, 0093, 0165,

1096

0019

0016

0186

0037

0000, 0650, 1003,

0010

0178, 0179, 0180,

0186, 1181

0003

0171, 1174

0180

0216

0000, 1003

0030, 0054

0171, 1174

0056, 0177, 0178,

1181

0093, 1096

13 Additional Information

CABLE TV/DTV

Manufacturer

ABC

Code

0003, 0007, 0008,

0011, 0014, 0017

0899 Americast

Bell & Howell

Bell South

Contec

Daehan

Daeryung

Everquest

0014

0899

0019

0778

0008

0015

Gemini 0015

General Instrument 0011, 0276, 0476,

GoldStar

Hamlin

Hitachi

0810

0144, 0838

0020

0011

Hytex

Jasco

Jerrold

LG Alps

Memorex

Now

0007

0015

0003, 0011, 0012,

0014, 0015, 0276,

0476, 0810

0779

0000, 1003

0776

Oak

Pacific

Panasonic

Paragon

Pioneer

0007, 0019

0678

0000, 0107, 1003

0000, 1003

0144, 0260, 0533,

0877, 1010(DTV),

1021

0000 Pulsar

Quasar

Radio Shack

Regal

Rembrandt

Runco

Samsung

0000

0015

0020

0011

0000

0144, 0702

Scientific Atlanta 0008, 0017, 0477,

0877

Seawoo

Sharp

Signal

Signature

Starcom

Stargate

Starquest

Taihan

Tocom

TongKook

Toshiba

Tusa

United Artists

Zenith

0780

0313, 1010(DTV)

0015

0011

0003, 0015

0015

0015

0778

0012

0777, 0840

0000

0015

0007

0000, 0525, 0899

61

En

13 Additional Information

SATELLITE TUNER

Manufacturer

AlphaStar

DX Antenna

Dae Young

Code

0772

0752

0735

Daeryung

Echostar

0396

0396, 0775, 1005

Expressvu 0775

General Instrument 0361, 0627, 0869

HTS

Hitachi

0775

0489, 0819

Hughes Network Systems 0749

Hung Chang 0732

Hyundai

JVC

0758

0492, 0505, 0506,

0775

0361, 0627 Jerrold

JiWon

Kabil

Magnavox

Marantz

Memorex

Mitsubishi

NEC

0364

0737

0722, 0724

0200

0724

0491

0496, 0499, 0507,

0508

Next Level

Now

Panasonic

Pantech

Philips

Pioneer

Primestar

RCA

0869

0757

0340, 0500, 0701,

0739

0747

0200, 0722, 0724

0662

0361, 0627

Radio Shack

Samsung

Sanyo

Sharp

Sony

Star Choice

Tae Kwang

Toshiba

Uniden

VTech

Victor

Zenith

0143, 0392, 0566,

0855

0869

0773

0493

0494,

0275, 0639, 0661

0869

0733

0486, 0790

0722, 0724

0321

0492, 0505, 0506

0856

CD PLAYER (1/2)

Manufacturer

ADC

Adcom

Aiwa

Anam

Audio-Technica

Burmester

Code

0018

0155

0124, 0157

0362

0170

0420

California Audio Labs 0029, 0303

Carver 0157, 0179, 0437

DKK

Denon

0000

0003, 0358, 0873

Dynamic Bass

Emerson

0179

0155, 0164, 0305,

0469

0562, 0563 Eroica

Fantasia

Fisher

GE

Garrard

Genexxa

0525

0174, 0179, 0342

0009

0280, 0393, 0420

0032, 0164, 0305

CD PLAYER (2/2)

Manufacturer

GoldStar

Harman/Kardon

Hitachi

Inkel

JVC

Kenwood

Krell

Kyocera

LXI

Linn

Lotte

Luxman

MCS

MTC

Magnavox

Marantz

Mission

NSM

Nikko

Onkyo

Optimus

Panasonic

Parasound

Philips

Pioneer

Proton

QED

Quasar

RCA

Realistic

Rotel

SAE

STS

Sansui

Sanyo

Scott

Sears

Sharp

Sherwood

Sony

Soundesign

Tandberg

Tascam

Teac

Technics

Toshiba

Victor

Wards

Yamaha

Yorx

0157, 0626

0032, 0244, 0305,

0468, 0551, 1062,

1063, 1087

0157

0157

0029

0009, 0053, 0155,

0179, 0305, 0764

0155, 0164, 0179,

0180, 0420

0157, 0420

0157

0018

0157, 0305

0087, 0179, 0349

0155, 0164, 0305

0305

0037, 0180, 0261,

0861

0065, 0114, 0180,

0426

0000, 0185, 0490,

0604, 0605

0145

0203

0420

0174, 0180, 0393,

0420

0029, 0303

0481

0072

0053, 0157

0036, 0170, 0187,

0261

0461

Code

0383, 0525

0157, 0173, 0426

0032, 0155

0065, 0114, 0180,

0203, 0437

0072

0028, 0037, 0190,

0626, 0681, 0826

0157

0018

0305

0157

0505

0266

0029

0420

0157, 0305

0029, 0157, 0180

0157

0157

0164, 0170, 0174,

0362, 0525

0101, 0381, 0868

0000, 0032, 0037,

0087, 0145, 0179,

0280, 0305, 0342,

0420, 0426, 0437,

0468, 1063

0029, 0303, 0367,

0752

0420

62

En

VCR (1/4)

Manufacturer

Admiral

Adventura

Aiko

Aiwa

Akai

America Action

American High

Anam

Anam National

Asha

Audiovox

Beaumark

Bell & Howell

Broksonic

CCE

Calix

Canon

Capehart

Carver

CASSETTE DECK

Kenwood

Kyocera

Lotte

Luxman

Magnavox

Marantz

Nakamichi

Nikko

Olympus

Onkyo

Optimus

Panasonic

Philips

Pioneer

Manufacture

ADC

Aiwa

Akai

Anam

Carver

Denon

Dual

Dynamic Bass

Eroica

Fisher

Garrard

GoldStar

Harman/Kardon

Inkel

JVC

RCA

Renaissance

Samsung

Sansui

Sanyo

Sherwood

Sonic

Sony

Teac

Technics

Victor

Wards

Yamaha

Code

1171

1029, 1197, 1223

1189

1364

1029, 1261

1076

1383

1261

1418

1261

1375

1375

1029, 1182

1070, 1337

1244, 1273

1070

1171

1339

1266

1029

1029

1218

1364

1266

1135, 1282

1027, 1220, 1337

1229

1029

1027, 1099, 1101,

1220

1261

1413

1391

1029

1261

1337

1375

1170, 1243, 1291

1391

1229

1244, 1273

1027

1094, 1097

Code

0048, 0209

0000

0278

0000, 0037

0041, 0315

0278

0035

0037, 0162, 0240,

0278, 0553, 0579

0162, 1162

0240

0037

0240

0104

0002, 0121, 0184,

0209

0072, 0278

0037

0035

0020

0081

VCR (2/4)

Manufacturer

Cineral

Citizen

Colt

Craig

Curtis Mathes

Code

0278

0037, 0278

0072

0037, 0047, 0072,

0240

0035, 0041, 0060,

0162

Cybernex

Daewoo

Daytron

Denon

Dynatech

Electrohome

Electrophonic

Emerex

Emerson

0240

0020, 0045, 0046,

0278

0020

0042

0000

0037

0037

Fisher

Fuji

Funai

GE

0032

0000, 0002, 0037,

0043, 0121, 0184,

0209, 0278

0047, 0104

0033, 0035

0000

0035, 0048, 0060,

Garrard

General

Go Video

GoldStar

0240

0000

0052

0432

Gradiente

HI-Q

Harley Davidson

Harman/Kardon

Harwood

Headquarter

Hitachi

0037, 0038, 0225,

0480

0000, 0008

0047

0000

0038, 0081

0072

0046

0000, 0041, 0042,

0235

Hughes Network Systems 0042

JVC 0008, 0041, 0067

Jensen

KEC

KLH

Kenwood

Kodak

LG

LXI

Lloyd's

0041

0037, 0278

0072

0038, 0041, 0067

0035, 0037

0480

0037

0000

Logik

MEI

0072

0035

MGA 0043, 0240

MGN Technology 0240

MTC

Magnasonic

Magnavox

0000, 0240

0278

0000, 0035, 0039,

0081, 0149

Magnin

Marantz

Marta

Matsushita

Memorex

0240

0035, 0081

0037

0035, 0162

0000, 0035, 0037,

0039, 0046, 0047,

0048, 0104, 0209,

0240, 1037, 1162,

Minolta

Mitsubishi

Motorola

Multitech

1262

0042

0043, 0048, 0067

0035, 0048

0000, 0072

Orion

Panasonic

ReplayTV

Ricoh

Runco

STS

Samsung

Sanky

Sansui

Sanyo

Scott

Sears

Semp

Sharp

Shintom

Shogun

Singer

Sony

Sylvania

Symphonic

TMK

Tatung

Teac

Technics

Penney

Pentax

Philco

Philips

Pilot

Pioneer

Portland

Profitronic

Proscan

Protec

Pulsar

Quarter

Quartz

Quasar

RCA

Radio Shack

Radix

Randex

Realistic

VCR (3/4)

Manufacturer

NAD

NEC

Nikko

Nikon

Noblex

Olympus

Optimus

0060, 0149, 0240,

0000, 1037

0037

0037

0000, 0035, 0037,

0046, 0047, 0048,

0104

0614, 0616

0034

0039

0042

0045, 0240, 0426,

0432

0039, 0048

0000, 0041, 0067,

0209

0046, 0047, 0104,

0240

0043, 0045, 0121,

0184

0000, 0035, 0037,

0042, 0046, 0047,

0104

0045

0048, 0363

0072

0240

0072

0000, 0032, 0033,

0034, 0035

0000, 0035, 0043,

0081

0000

0240

0041

0000, 0041

0035, 0162

Code

0058

0038, 0040, 0041,

0067, 0104

0037

0034

0240

0035

0037, 0048, 0058,

0104, 0162, 0432,

1048, 1062, 1162,

1262

0002, 0184, 0209

0035, 0162, 0225,

0616, 1062, 1162,

1262

0035, 0037, 0038,

0040, 0042, 0240

0042

0035, 0209

0035, 0081, 0618

0037

0058, 0067, 0168

0020

0240

0060,

0072

0039

0046

0046

0035, 0162, 1162

0035, 0042, 0048,

13 Additional Information

VCR (4/4)

Manufacturer

Teknika

Code

0000, 0035, 0037,

0052

0000 Thomas

Tivo

Toshiba

Totevision

Unitech

0618

0043, 0045

0037, 0240

0240

Vector 0045

Vector Research 0038, 0040

Victor

Video Concepts

Videosonic

Wards

0008, 0041, 0067

0040, 0045

0240

0000, 0035, 0042,

0047, 0048, 0060,

0072, 0081, 0149,

0240

White Westinghouse 0209, 0278

XR-1000

Yamaha

Zenith

0000, 0035, 0072

0038

0000, 0033, 0034,

0039, 0209

MD RECORDER AND CD RECORDER

Manufacturer

Denon

Kenwood

Onkyo

Optimus

Philips

Pioneer

Sharp

Sony

Code

0873

0626, 0681, 0826

0868

1063

0626

1062, 1063,

1087(CD-R)

0861

0490

63

En

13 Additional Information

Troubleshooting

Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified after checking the items below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

The disc is ejected automatically after loading.

• Dirty or damaged disc.

See page 57 for disc care information.

• Disc not seated properly in the disc guide.

Align the disc properly.

• Incompatible region number.

If the region number on a DVD-video disc does not match the number on the DVD tuner, the disc cannot be used (page 6).

• Condensation inside the unit.

Allow time for condensation to evaporate. Avoid using the player near an air-conditioning unit.

New settings made in the Setup screen menus while a disc is playing are ineffective.

• Some settings can be changed while a disc is playing, but are not effective until the disc is stopped then restarted.

This is not a malfunction.

Make the same setting when the disc is stopped.

Press

7, then restart playback (3). Note that making settings in the Setup screen menus may cancel the

RESUME

function.

Settings are canceled.

• When the power is cut due to power failure or by unplugging the power cord, settings will be canceled.

Playback is not possible.

• Disc is loaded upside down.

Reload the disc with the label side face up.

• In the case of CD-R and CD-RW discs, make sure that the recording has been finalized following the procedures in the manual supplied with the recording component.

No picture/No color.

• Incorrect video connections.

Check that connections are correct and that plugs are inserted fully.

• TV/monitor settings are incorrect.

Check the instruction manual of the TV/monitor.

mark appears on screen.

• The operation is prohibited by the system.

mark appears on screen.

• The selected function does not operate for that disc.

Screen is stretched or aspect does not change.

• The TV Screen setting in the Setup menu is incorrect.

Set the TV Screen option to match the TV/monitor you're using (page 35).

When making changes in the Setup OSD menus, is displayed.

• There is a CD or Video CD loaded and the setting that was changed applies only to DVD discs.

The settings will take effect next time a DVD is loaded.

Picture playback stops and the operation buttons cannot be used.

Press

7, then start playback again (3). Switch the power off once, then on again using the front panel

STANDBY

/

ON

switch.

64

En

Picture disturbance during playback or dark.

• This player is compatible with Macro-Vision System copy guard. Some discs include a copy prevention signal, and when this type of disc is played back, stripes etc., may appear on some sections of the picture depending on the

TV.

This is not a malfunction.

• Different discs respond in different ways to some functions.This may result in the screen becoming black for a brief instant or shaking slightly when the function is executed.

These problems are largely due to differences between discs and disc content and are not malfunctions of this system.

When recorded on a VCR or passed through an

AV selector, there is disturbance in the playback picture.

• Due to copy protection, connection of this system through a VCR or an AV selector may prevent recording or cause picture problems.

This is not a malfunction.

The remote control doesn't seem to work.

• The remote control is too far from the system, or the angle with the remote sensor is too wide.

Use the remote within its operating range (See the separate Setting Up guide).

• The batteries are exhausted.

Put in new batteries (See the separate Setting Up guide).

No 96kHz signal from the digital audio output

Linear PCM Out is set to 96kHz

348kHz.

Set to 96kHz.

• As a copy-protection measure, some DVDs do not output

96kHz audio.

In this case, even if 96kHz is selected, the player automatically outputs the audio at 48 kHz. This is not a malfunction.

13 Additional Information

No audio, or audio is distorted.

• Dirt, dust, etc. on the disc.

Clean the disc (page 57).

• Interconnects are not fully inserted into the terminals (or are not connected).

Check that all interconnects are firmly inserted.

• Dirty or oxidized plugs/terminals.

Clean the plugs/terminals.

• Incorrect audio cable connection.

Check the audio connections (See the separate Setting

Up guide).

• The disc is paused.

Press

3 or 8 to exit the pause mode.

• Incorrect settings.

Check that the volume is turned up, that the speakers are on, the input function set correctly, etc.

• Mute is on.

Press mute (remote control only) to switch mute off.

Noticeable difference in DVD and CD volume.

• DVDs and CDs use different recording methods.

This is not a malfunction.

65

En

13 Additional Information

Noisy radio reception

• Antennas are not connected properly.

Check the connections. For FM, make sure that the antenna is fully extended and positioned to give the best reception (See the separate Setting Up guide).

For AM, make sure that the loop antenna is pointing in the best direction (See the separate Setting Up guide).

• The frequency is incorrect.

Check the radio frequency.

• The radio signal is weak.

If the radio signal is weak, an outdoor antenna will usually give better results than the supplied indoor types.

• Other electrical equipment is causing interference.

Other electrical equipment, such as TVs, fluorescent lamps and motors can cause interference. Try switching off or moving the equipment, or moving the antenna(s).

Screen sizes and disc formats

The table below shows the effect of various TV Screen settings on the different kinds of disc available.

When viewing a wide screen TV or monitor

Setting and Appearance Screen format of disc

Widescreen (movies, etc.)

Note that some extra-wide formats

(such as CinemaScope) will appear with black bars at the top and bottom of the screen.

16:9 (Wide)

Standard (TV programs, etc.)

Your TV will determine how the picture is presented—check the manual that came with the TV for details. Typical options are black bars either side, some form of stretched or zoomed presentation.

Auto tuning does not pick up some stations.

• The radio signal is weak.

Auto tuning will only detect radio stations with a good signal. For more sensitive tuning, connect an outdoor antenna.

Note: Static electricity or other external influences may cause malfunctioning of this unit. In this case, unplug the power cord and then plug back in. This will usually reset the unit for proper operation. If this does not correct the problem, please consult your nearest Pioneer service center.

Resetting the system

Resetting the system returns all menu, picture and password settings to their factory defaults.

Switch the system into standby using the front panel

STANDBY

/

ON

switch. Next, hold down the front panel

7 button and switch back on. All settings will have been cleared.

16:9 (Wide)

When viewing a standard size TV or monitor

Setting and Appearance Screen format of disc

Standard (TV programs, etc.)

The program is presented correctly, regardless of the setting.

Any setting

Widescreen (movies, etc.)

The program is shown in widescreen with black bars at the top and bottom of the screen.

4:3 (Letter Box)

Widescreen (movies, etc.)

The sides of the program are cropped so that the picture fills the whole screen.

4:3 (Pan & Scan)

Widescreen (movies, etc.)

The program appears squashed: set to either 4:3 ( Letter Box) or 4:3

( Pan & Scan).

16:9 (Wide)

66

En

13 Additional Information

Component features & functions

DVD Tuner System

STANDBY/ON button

STANDBY indicator

DVD indicator

OPEN/CLOSE button

Disc table

Powered Subwoofer Unit

Power cord connector

FUNCTION button

VOLUME up button

VOLUME down button

Stop button

Pause button

PHONES jack

Play button

Control cable jack (blue) A

FM antenna terminals

Analog jacks for auxiliary components

Control cable

jack (black) B

Control cable jack (blue) A

Speaker terminals

AM antenna terminals

Digital jacks for auxiliary components

Display cable jack

Control cable jack (black) B

Display Unit

Display

Remote control sensor

Display cable jack

67

En

Specifications

Amplifier Section

Continuous power output (RMS)

Front, Center, Rear ........................... 40W, per channel

(1kHz, 10% T.H.D., 8

)

Subwoofer ................... 65W (100Hz 10% T.H.D., 8

)

Speakers Section

Front, Rear, Center speakers

Type Sealed, antimagnetic (EIAJ)*

Speaker .............................. 8.7cm (3-7/16 in.) (cone type)

Nominal impedance ........................................................ 8

Frequency range ...................................... 100 to 20,000 Hz

Max. input ........................................................... 40 W (EIAJ)

Powered subwoofer

Type ................. Bass reflex floor type, antimagnetic (EIAJ)*

Speaker ........................................ 16 cm (6 in.) (cone type)

Nominal impedance ........................................................ 8

Frequency range ........................................ 25 Hz to 300 Hz

Max. input ........................................................... 65 W (EIAJ)

* Antimagnetic design (EIAJ) speaker system conforms to the basic EIAJ standards.

DVD Player (Audio)Section

S/N ratio ........................................................... 115 dB (EIAJ)

Dynamic range ................................................. 100 dB (EIAJ)

Distortion ................................................................. 0.004%

Frequency response

48 kHz sampling .................................. 4 Hz to 22 kHz

96 kHz sampling .................................. 4 Hz to 44 kHz

Wow & flutter ................................. Below measurable levels

(

±

0.001% W.PEAK)

DVD Player (Video) Section

Output level ................................................... 1 Vp-p (75

)

Video Y output level ...................................... 1 Vp-p (75

)

Video C output level ............................... 286 mVp-p (75

)

DVD (Other jacks) Section

Digital optical output (PCM/2/DTS) ... Optical connector

Digital optical input (PCM/2/DTS) ...... Optical connector

Digital coaxial input (PCM/2/DTS) ...... Coaxial connector

Tuner Section

FM tuner

Frequency range .................... 87.5 MHz to 108.0 MHz

Antenna ............................................. 75

unbalanced

AM tuner

Frequency range ....................... 531 kHz to 1,602 kHz

(9 kHz step)

Antenna ................................. loop antenna (supplied)

Power Supply Section

Power requirements

Australian model ......................... AC 240 V, 50/60 Hz

Multi voltage model ....... AC 110-127/220-230/240 V

(Switchable), 50/60 Hz

Power consumption

Australian model ................................................ 160 W

Multi voltage model ............................................. 418 W

Power consumption in standby mode ............................ 1 W

Miscellaneous

DVD tuner system

Dimensions .............. 280 (W) x 240 (D) x 82 (H) mm

(11(W) x 9-7/16 (D) x 3-1/4 (H) in.)

Weight ................................................. 3.1 kg (6.8 lbs)

Powered subwoofer unit

Dimensions ............ 190 (W) x 425 (D) x 430 (H) mm

(7-1/2 (W) x 16-3/4 (D) x 17 (H) in.)

Weight .......................................... 13.8 kg (30.15 lbs)

Front, Rear speakers

Dimensions ................ 110 (W) x 75 (D) x 154 (H) mm

(4-5/16 (W) x 2-15/16 (D) x 6 (H) in.)

Weight ............................................... 0.76 kg (1.7 lbs)

Center speaker

Dimensions ................ 210 (W) x 75 (D) x 110 (H) mm

(8-1/2 (W) x 2-15/16 (D) x 4-5/16 (H) in.)

Weight ............................................... 0.83 kg (1.8 lbs)

Display unit

Dimensions ................. 210 (W) x 62 (D) x 86 (H) mm

(8-1/2 (W) x 2-7/16 (D) x 3-3/8 (H) in.)

Weight ................................................. 0.23 kg (.51 lb)

Operating conditions:

Temperature .............. +5°C to +35°C (+41°F to 95°F)

Humidity ............. 5% to 85% (without condensation)

Supplied Items

Remote control .................................................................... 1

Alkaline Batteries (AA/LR6) ............................................... 2

Display unit .......................................................................... 1

AM loop antenna ................................................................. 1

FM antenna .......................................................................... 1

Video cable .......................................................................... 1

Power cord ........................................................................... 1

Display cable ....................................................................... 1

Control cable A (Blue) ....................................................... 1

Control cable B (Black) ..................................................... 1

Speaker cords (5 m/16 ft. 3 in.) ........................................ 3

Speaker cords (10 m/32 ft. 6 in.) ...................................... 2

Cord labels ........................................................................... 1

Non-skid pads ..................................................................... 1

Operating instructions (Setting up) ................................... 1

Operating instructions (Basic/Detailed) ........................... 1

Warranty .............................................................................. 1

Note: Specifications and design subject to possible modification

without notice, due improvements.

Published by Pioneer Corporation.

Copyright © 2000 Pioneer Corporation.

All rights reserved.

PIONEER CORPORATION

4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS [USA] INC.

P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A.

PIONEER ELECTRONICS OF CANADA, INC.

PIONEER EUROPE NV

300 Allstate Parkway, Markham, Ontario L3R OP2, Canada

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.

178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: [03] 9586-6300

San Lorenzo 1009 3er Piso Desp. 302 Col. Del Valle Mexico D.F. C.P. 03100

TEL: 5-688-52-90

<00F00ZF0H00> Printed in <ARB7228-A>

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals