Siemens Serie IQ Installation manual

IQ-400 - Series Intelligent Access Control Systems
Installation Manual
33-10057-001
REV: A
PCSC
3541 Challenger Street
Torrance, CA 90503
Phone: (310) 638-0400
FAX: (310) 638-6204
www.1pcsc.com
First Edition: February 2004
Information in this manual is subject to change without notice and does not represent a
commitment on the part of PCSC. The software described in this manual is furnished under a
license agreement or nondisclosure agreement. The software may be used or copied only in
accordance with the terms of the agreement. No part of this document may be reproduced or
transmitted in any form or by any means, electronic or mechanical, including photocopying,
recording, or information storage and retrieval systems, for any purpose other than specified in
the agreement, without the express written permission of PCSC.
 2004 PCSC. All Rights Reserved.
Printed in the United States of America.
Published by PCSC
3541 Challenger Street
Torrance, CA 90503
(310) 638-0400
(310) 638-6204
Publication Number: 33-10057-001-A
IQ-400 Installation Manual
Page ii of 100
33-10057-001-A
0.1 Board Diagrams
0.1.1
The IQ-400 Printed Circuit Board Wiring Diagram
IQ-400 Installation Manual
Page iii of 100
33-10057-001-A
0.1.2 Four-Door Expansion Board
IQ-400 Installation Manual
Page iv of 100
33-10057-001-A
0.1.3 Eight-Door Expansion Board
IQ-400 Installation Manual
Page v of 100
33-10057-001-A
0.1.4 OUT Expansion Board
IQ-400 Installation Manual
Page vi of 100
33-10057-001-A
0.1.5 ALM Expansion Board
IQ-400 Installation Manual
Page vii of 100
33-10057-001-A
0.1.6 SAM Board
IQ-400 Installation Manual
Page viii of 100
33-10057-001-A
0.2 Table of Contents
IQ-400 - Series Intelligent Access Control Systems ...................... i
0.1 Board Diagrams.......................................................................................................................iii
0.1.1 The IQ-400 Printed Circuit Board Wiring Diagram.........................................................iii
0.1.2 Four-Door Expansion Board ............................................................................................. iv
0.1.3 Eight-Door Expansion Board ............................................................................................. v
0.1.4 OUT Expansion Board...................................................................................................... vi
0.1.5 ALM Expansion Board ......................................................................................................vii
0.1.6 SAM Board........................................................................................................................vii
0.1.6 SAM Board.......................................................................................................................viii
0.2 Table of Contents ................................................................................................................... ix
1.0 Introduction................................................................................................... 1
2.0 Unpacking the IQ-400 ................................................................................... 2
2.1 Unpacking the IQ-400 ............................................................................................................. 2
2.2 Visual Inspection................................................................................................................... 2
3.0 Installing Power ............................................................................................ 6
3.1 Installing Power ....................................................................................................................... 6
3.1.1 Installing Power- 3.0 Amp.................................................................................................. 6
3.1.2 Installing Power- 6.0 Amp.................................................................................................. 6
3.1.3 Figure - PCSC 3.0 Amp Power Supply.............................................................................. 7
3.1.4 Figure - PCSC 6.0 Amp Power Supply.............................................................................. 8
3.1.5 Resetting the IQ-400 to Default Values ............................................................................. 9
4.0 Wiring Your Readers .................................................................................. 10
4.1 Grounding Your Readers ...................................................................................................... 10
4.2 Properly Routing Your Cables............................................................................................... 10
4.3 Grounding the Power and Data Lines ................................................................................... 11
4.3.1 Procedure ........................................................................................................................ 11
4.4 Grounding the Pin Pad or Reader ......................................................................................... 13
4.4.1 Procedure ........................................................................................................................ 13
4.4.2 Grounding the Reader Mullion Mount.............................................................................. 14
IQ-400 Installation Manual
Page ix of 100
33-10057-001-A
5.0 Reader Connections .................................................................................. 15
5.0.1. Reader Disconnect Resistors ......................................................................................... 15
5.1 Reader Connections: BR-350 Readers: IQ-400 Board ......................................................... 16
5.2 Reader Connections: BR-350 Readers: Expansion Board ................................................... 17
5.3 Reader Connections: BR-370 Readers: IQ-400 Board ......................................................... 18
5.4 Reader Connections: BR-370 Readers: Expansion Board ................................................... 19
5.5 Reader Connections: PR233 MiniProx / PR-733/732: IQ-400 Board - Option 1................... 20
5.6 Reader Connections: PR233 MiniProx / PR-733/732: IQ-400 Board - Option 2................... 21
5.7 Reader Connections: PR-233 Miniprox/ PR733/ 732: Expansion Board – Option 1 ........... 22
5.8 Reader Connections: PR-233 Miniprox / PR733 / 732: Expansion Board – Option 2 ......... 23
5.9 Reader Connections: PR-234 / PRK-234 ProxPro / PR736 / PRK-736: IQ-400 Board ........ 24
5.10 Reader Connections: PR-234 / PRK-234 ProxPro / PR736/ PRK-736: Expansion Board . 25
5.11 Reader Connections: PR-235 MaxiProx / PR-735: IQ-400 Board ...................................... 26
5.12 Reader Connections: PR-235 MaxiProx / PR735: Expansion Board.................................. 27
5.13 Reader Connections: Sensor Wiegand: IQ-400 Board ....................................................... 28
5.14 Reader Connections: Sensor Wiegand: Expansion Board ................................................. 29
5.15 Reader Connections: VeriProx: IQ-400 Board .................................................................... 30
5.16 Reader Connections: VeriProx: Expansion Board .............................................................. 31
6.0 Wiring the Door(s) ...................................................................................... 32
6.1 Panel in a Fail-Safe Environment.......................................................................................... 34
6.2 Panel in a Fail-Secure Environment...................................................................................... 35
6.3 Expansion Board Door Lock/Strike ....................................................................................... 36
6.4 Expansion Board Open Collector .......................................................................................... 37
6.5 Egress Sense for IQ-400 and Expansion Boards ................................................................. 38
6.6 Door Sense for IQ-400 and Expansion Boards..................................................................... 39
6.6.1 Using the Ten Discrete LEDs .......................................................................................... 40
6.6.2 Expansion Board LED Arrays .......................................................................................... 41
6.7 Supervised Sense Inputs for P5 and P19 and Unsupervised Tamper at P8 ........................ 42
6.8 Expansion Board Supervised Door Senses and Supervised Request-to-Exit Sense Inputs 44
6.9 Expansion Board Supervised Door Sense Locations ........................................................... 45
6.10 Installing Noise Suppression Devices ................................................................................. 46
6.10.1 Procedure ...................................................................................................................... 46
7.0 Communicating with the IQ-400................................................................ 47
7.1 Reset the IQ-400 Panel ......................................................................................................... 47
7.2 Calibrating the IQ-400 Panel ................................................................................................. 48
7.3 Addressing Individual IQ-400s through the Dipswitch........................................................... 48
7.3 Addressing Individual IQ-400s through the Dipswitch........................................................... 49
7.3.1 Dipswitching the IQ-400 Address (1-111)........................................................................ 49
7.3.2 Software Addressing the IQ-400 Panel (Panels 112-200) Direct Connect...................... 50
7.4 Setting MODEM or Direct Connect Configurations ............................................................... 51
7.4.1 Ensuring Proper Configuration of the MODEM ............................................................... 52
7.4.2 Establishing a Proper Connection with a MODEM Cable ............................................... 53
7.5 Changing the Baud Rate ....................................................................................................... 54
7.6 Direct Connecting with One IQ-400....................................................................................... 56
7.6.1 Wiring Diagram- IQ-400 to PC, RS-232 w/DB9 Connector ............................................. 58
7.6.2 Wiring Diagram – IQ 400 to PC, RS -232 w/ DB25 Connector ....................................... 58
7.7 RS-232 Cable Connections...................................................................................................59
7.8 Communicating with Multiple IQ-400s (via RS-485) ............................................................. 60
7.8.1 Wiring Diagram of Multiple IQ-400s................................................................................. 60
7.8.2 Wiring Diagram of Multiple IQ-400s and MicroLPMs....................................................... 61
7.9 Real Time Serial Printing with the IQ-400 ............................................................................. 62
IQ-400 Installation Manual
Page x of 100
33-10057-001-A
8.0 Status Lights and Dealing with Communication Errors.......................... 63
8.1 Status Lights.......................................................................................................................... 63
8.2 Communication Errors........................................................................................................... 64
8.2.1 LED Fatal Error Display Codes........................................................................................ 64
8.2.2 Error Codes...................................................................................................................... 65
8.3 Control Counters and Sense Input Numbers for Output Control PCB .................................. 66
8.4 Proper Setting of SAM 1 and SAM 2..................................................................................... 68
8.5 IQ Systems Upgrades and Capacities .................................................................................. 69
8.6 RS-232/485 Terminal Servers............................................................................................... 70
8.7 RS-232-485/422 Converters: Printed Circuit Board Layout .................................................. 71
8.8 User Selectable Options........................................................................................................ 72
8.9 Point Definitions..................................................................................................................... 73
8.9.1 Sense Inputs .................................................................................................................... 73
8.9.2 Outputs ............................................................................................................................ 76
9.0 Appendix A - IQ-400 Specifications .......................................................... 79
9.1 IQ-400 Features .................................................................................................................... 79
9.1.1 System Capacities ........................................................................................................... 79
9.1.2 Spare Parts- IQ-400 PCB ................................................................................................ 79
9.2 IQ 4-Reader Expansion Module (P/N: 03-10102-301E)........................................................ 80
9.2.1 Power Supply................................................................................................................... 80
9.2.2 Door Sense LEDs ............................................................................................................ 80
9.3 IQ-800 Features (IQ-400 plus 4-Reader Expansion Module) ............................................... 81
9.3.1 Two Auxiliary (Powered) Outputs (cc# 89, 90) ................................................................ 81
9.3.2 System Capacities ........................................................................................................... 81
9.3.3 Spare Parts- 4-Reader Expansion Board (P/N: 03-10102-301E).................................... 81
9.4 IQ 8-Reader Expansion Module (P/N: 03-10102-201E)........................................................ 82
9.4.1 Power Supply................................................................................................................... 82
9.4.2 Door Sense LEDs ............................................................................................................ 82
9.5 IQ-1200 Features (IQ-400 plus 8-Reader Expansion Module) ............................................. 83
9.5.1 System Capacities ........................................................................................................... 83
9.5.2 Spare Parts- 8-Reader Expansion Board (P/N: 03-10102-201F).................................... 83
9.6 OUT PCB Features (P/N: 03-10032-201F) ........................................................................... 84
9.6.1 System Capacities ........................................................................................................... 84
9.6.2 Electrical Ratings ............................................................................................................. 84
9.6.3 Spare Parts- OUT PCB.................................................................................................... 84
9.7 ALM PCB Features (P/N:P 03-10032-301) ........................................................................... 85
9.7.1 System Capacities ........................................................................................................... 85
9.7.2 Electrical Ratings ............................................................................................................. 85
9.7.3 Spare Parts- ALM PCB (P/N: 03-10032-301).................................................................. 85
9.8 Cable Requirements and Maximum Lengths ........................................................................ 86
9.8.1 Communication-............................................................................................................... 86
9.8.2 Readers ........................................................................................................................... 86
9.9 Tool Requirements ................................................................................................................ 87
9.10 Controller Specifications...................................................................................................... 87
9.11 Four-Reader Expansion Board- Active LEDs (P/N: 03-10102-301E) ................................. 89
9.11.1 Jumpers ......................................................................................................................... 89
9.11.2 Four-Reader Expansion Board (P/N: 03-10102-301E) - Jumper Selections ................ 90
9.12 Eight-Reader Expansion Board (P/N: 03-10102-201E) - Active LEDs ............................... 91
9.12.1 Jumpers ......................................................................................................................... 91
9.12.2 Eight-Reader Expansion Board (P/N: 03-10102-201E) - Jumper Selections................ 92
IQ-400 Installation Manual
Page xi of 100
33-10057-001-A
10.0 Appendix B – Configuring the IQ LAN for Version 0130 and above .... 93
10.1 Configuring the IQ LAN for Version 0130 and above.......................................................... 93
10.1.1 Required Equipment: .....................................................................................................93
10.1.2 Required Information: .................................................................................................... 93
10.1.3 Required firmware:......................................................................................................... 93
10.2 Configuring your Host Computer......................................................................................... 94
10.3 Configuring IQ LAN VIA the TCP/IP Configurator............................................................... 95
10.3.1 TCP/IP Configuration ..................................................................................................... 96
10.4 Resetting the LAN (External Peripheral or Embedded) Ethernet Module........................... 99
End of Manual ................................................................................................... 100
IQ-400 Installation Manual
Page xii of 100
33-10057-001-A
1.0 Introduction
Welcome to the IQ-400, the newest generation of intelligent access control system from PCSC,
which expands on the existing qualities of the IQ-400 with the expanded ability to make four
reader connections per panel.
This manual explains IQ-400 installation and connection to a personal computer (PC) and an
optional local printer. The IQ-400 Manual is divided up into six steps:
Step 1 - Unpacking the IQ-400
Step 2 - Installing Power
Step 3 - Wiring Your Readers
Step 4 - Reader Connections
Step 5 - Wiring Your Door(s)
Step 6 - Communicating with the IQ-400
Step 7 - Status Lights and Dealing with Communication Errors
Before turning on the IQ-400 or the PC, take a moment to read through this manual. It has been
designed to allow you to move through the installation process. Specifics about the IQ-400 and its
component systems can be found in:
Appendix: A - IQ-400 Specifications
Appendix B - Configuring the IQ-400 LAN for Version 0130 and above
NOTE The IQ-400 system is set up at the factory. Do NOT re-initialize the
system unless other modules have been added.
The LiNC-NET Network Controller communicates on a multi-point RS485 communication cable
(RS-232 and MODEM communication are also available). You must address each IQ-400 with a
unique ID number (1-111) in order to communicate to each IQ-400 panel. Numbering the IQ-400s
should be in ascending order, but it is not required for operation.
NOTE Installation must meet all local, state, and federal regulations and codes
for electrical installation. If these codes conflict with the installation
methods described in this manual, please call your service
representative.
UL LISTINGS
The IQ-400 control unit is UL listed to the standard for Access Control System
Units, UL 294. The following card readers have been found compatible by UL
with the IQ-400: PCSC Models BR-370 and BR-470; HID Models PR-234 and
PRK-234; and AWID PR-732, 733.
IQ-400 Installation Manual
Page 1 of 100
33-10057-001-A
2.0 Unpacking the IQ-400
2.1 Unpacking the IQ-400
As you unpack the IQ-400, inspect it for missing items or damage. Contact the dealer for any
irregularities. Keep ALL packing material for protection in return shipping.
2.2 Visual Inspection
1. Are all of the socketed integrated circuit chips seated in their sockets?
Socket ICs U105 and U108 are located in the center of the board in close vicinity to LEDs
D50 and D49.
2. Are the door relays seated and latched into their sockets?
The Door Relays K1, K2, K3 and K4 are locked at the bottom center of the board.
3. Is the watch battery seated in its socket?
The watch battery is located in socket BT1 located in the lower left side of the board near to
the DB9 Connector P7.
4. Are all of the plug-on connectors affixed to their male header connectors?
Plugs on connectors are located along the left-hand edge of the board at plug P1-P2-P3-P4P5-P6. Plugs on connectors are located along the bottom portion of the board at plug P8-P9P10-P11-P12-13-P14-P15. Plugs on connectors are located along the lower right-hand edge
of the board at plug P16-P17-P18-P19.
5. Is the fuse in place at socket F1 located in the upper left corner of the board?
A 4-Amp fast blow (3AG) fuse is required.
IQ-400 Installation Manual
Page 2 of 100
33-10057-001-A
Are the jumpers in place at W1, W2, W3, W4, and W8?
•
Jumper W8 is located in the LOWER RIGHT side of the board and is set for 12 volt-4wire, 12 volt-5-wire, or 5-volt-5-wire readers.
-
Across Pins #1 and #2 = 5 Volt Card Reader
-
Across Pins #2 and #3 = 12 Volt Card Reader
-
Across Pins #4 and #5, #7 and #8, #10 and #11 =
5-wire Wiegand Data (Data0, Data1) Format
-
Across Pins #5 and #6, #8 and #9, #11 and #12 =
4-wire PCSC Data Format
IQ-400 Installation Manual
Page 3 of 100
33-10057-001-A
•
•
•
Jumper W2 is located in the LOWER RIGHT side of the board, to the left of Plug P16
and is set for 4 or 5 wire readers. (Must be set consistently with Data format set on
W1, W3 and W4).
-
Across Pins #1 and #2 = 5-wire Wiegand Data (Data0, Data1) format
-
Across Pins #2 and #3 = 4-wire PCSC Data format
Jumper W1 is located in the LOWER RIGHT (CENTER) side of the board, to the left
of W2 and is set for 4 or 5 wire readers. (Must be set consistently with Data format set
on W2, W3 and W4).
-
Across Pins #1 and #2 = 5-wire Wiegand Data (Data0, Data1) format
-
Across Pins #2 and #3 = 4-wire PCSC Data format
Jumper W4 is located in the LOWER LEFT (CENTER)side of the board, to the left of
W1 and is set for 4 or 5 wire readers.
NOTE: It must be set consistently with data format set on W1, W2 and W3.
•
-
Across Pins #1 and #2 = 5-wire Wiegand Data (Data0, Data1) format
-
Across Pins #2 and #3 = 4-wire PCSC Data format
Jumper W3 is located in the LOWER LEFT side of the board to the left of W4 and is
set for 4 or 5 wire readers.
NOTE: It must be set consistently with data format set on W1, W2 and W4.
-
Across Pins #1 and #2 = 5-wire Wiegand Data (Data0, Data1) format
-
Across Pins #2 and #3 = 4-wire PCSC Data format
IQ-400 Installation Manual
Page 4 of 100
33-10057-001-A
IQ-400 - Expansion Cable Plug
•
Is the 50-pin Expansion Bus Ribbon Cable connected to the IQ-200 at Plug J1?
The RED stripe on the edge of the ribbon cable should be connected to pin #1
of Plug J1.
•
Is the opposite end of the 50-pin Expansion Buss Ribbon Cable connected to a
Peripheral Expansion Board at Plug P1?
The possible expansion boards are the new 4-door expansion PCB, 8-door PCB,
OUT PCB, ALM PCB, SAM PCBs.
IQ-400 Installation Manual
Page 5 of 100
33-10057-001-A
3.0 Installing Power
3.1 Installing Power
Shown below are the 3.0A and 6.0A PCSC power supplies. Both power supplies are shown in
enclosures connected to an IQ-400 manual in a PCSC small enclosure.
3.1.1 Installing Power- 3.0 Amp
See Figure 1 in Section 3.1.3.
12VDC power is connected to the circuit board at P1 in the upper left corner. Disconnect
power mains from the supply until the wiring is secured.
3.1.2 Installing Power- 6.0 Amp
See Figure 2 in Section 3.1.4.
12VDC power is connected to the circuit board at P1 in the upper left corner. Disconnect
power mains from the supply until the wiring is secured.
NOTE: Power supply cable connections are non power-limited outputs. For more information,
please refer to the power supply installation manual.
IQ-400 Installation Manual
Page 6 of 100
33-10057-001-A
3.1.3 Figure - PCSC 3.0 Amp Power Supply
IQ-400 Installation Manual
Page 7 of 100
33-10057-001-A
3.1.4 Figure - PCSC 6.0 Amp Power Supply
IQ-400 Installation Manual
Page 8 of 100
33-10057-001-A
3.1.5 Resetting the IQ-400 to Default Values
In the event that the 3-volt watch battery is removed or loses its electrical charge, the IQ400 must be reset. Follow the procedures below to restore the controller to the default
values.
1. With power on, move all switches at dipswitch SW1 to the right, OFF (as printed on the circuit
board).
2. Press the Reset button at S1.
3. The 10 LEDs (D39 – D48) will flash in waterfall effect and then stop. The 7-segment LEDs
(D49 and D50) will show 8.8. while the reset process is underway. When the reset process is
complete, all 10 LEDs (D39 – D48) will turn OFF, and the seven segment LEDs will show a
single line segment flashing in a circular pattern clockwise.
4. Refer to Section 7.3 [Addressing Individual IQ-400s through the Dipswitch] and begin
addressing the IQ-400 by DIP switching the panel number (1-111).
5. Set the communication protocol by following the instructions on section 7.4 [Setting MODEM
or Direct Connect Configurations].
6. The system is now set to the default values. Refer to Quick Setup Steps for page references.
IQ-400 Installation Manual
Page 9 of 100
33-10057-001-A
4.0 Wiring Your Readers
4.1 Grounding Your Readers
PCSC has designed its products to withstand most inductive voltage spikes without effect.
However, some noise found in power supplies and door strikes, in addition to static discharge,
may cause the control unit to momentarily shut down, lockup, or in extreme cases, to become
damaged. Unexplained lockups and intermittent system behavior are common symptoms of static
or noise problems. If cycling power will remedy your problem, carefully follow these instructions:
1. Install MOVs (Metal Oxide Varistors, Siemens S10K30 or the equivalent) or reversed biased
diodes (1N4004 - 1N4007) at each Door Strike. When installed, they will suppress most
problem Door Strikes.
2. Readers should be properly earth-grounded for uninterrupted reads. Please be aware that
operation is affected by the amount of static present during certain times of the year.
3. Properly grounding all readers and hardware, in addition to suppressing noise in the
peripheral equipment, should allow for many problem free years of use with PCSC products.
4. In addition, PCSC recommends using a separate filtered, electronically regulated output,
switchable power supply for door strikes.
5. Before installing the reader, please read the following instructions. Damage may occur if this
is disregarded.
6. Installation must meet all local, state, and federal regulations and codes for electrical
installation. If these codes conflict with the installation methods described in this manual,
please call your service representative.
4.2 Properly Routing Your Cables
Do not route data and power cables in the same conduit. Crosstalk and transmission of electrical
noise may result. The IQ-400 PCB’s will become damaged if the power cable grounds to the data
cable.
IQ-400 Installation Manual
Page 10 of 100
33-10057-001-A
4.3 Grounding the Power and Data Lines
Each cable has a set of drain lines that can be attached on the Host or controller end of the cable
to any screws mounted in the optional enclosures. If other non-metallic enclosures are used for
controller housing, ensure that an alternative source for earth grounding is available.
4.3.1 Procedure
1. At the Reader side, it is important to be aware of both the static generated from the user end
as well as electrical grounding from the data and power cabling. If at all possible, the reader
mounting plate should be attached to a grounded junction box or to another source, if the
junction box is non-metallic. This alleviates the possible damage caused by static electricity.
NOTE Leave the drain line taped back and floating at the reader site.
2. If grounding locally is not possible, connect drain wires to provided ESD (Electro Static
Discharge) hardware at the Controller side (enclosure) or to earth grounded conduit. As each
reader port is progressively farther away from the ESD hardware location (left rear side of the
cabinet for IQ-400s), allow for enough drain line to reach the ESD hardware on the controller
end of the cable. Allow enough strain relief to avoid touching other circuitry or creating
excessive tension.
IQ-400 Installation Manual
Page 11 of 100
33-10057-001-A
NOTE: The Small Enclosure that is described with Dimensions of 18”H x 6”D x 11”W has
been previously Evaluated and Listed for use with UL 1076 and UL 294 Systems.
IQ-400 Installation Manual
Page 12 of 100
33-10057-001-A
4.4 Grounding the Pin Pad or Reader
The card-reader is comprised of a housing and a mounting plate. The mounting plate is typically
attached to a single-gang, 2 x 4 inch earth-grounded junction box (preferably metal-type). The
reader may be installed either vertically or horizontally, depending on the installation
requirements.
4.4.1 Procedure
1. Orient the mounting plate so that the protruding ears are on top and facing the back of the
reader or PIN Pad. Attach the mounting plate to the junction box using two #6-32 x 3/8” flat
head screws. The mounting plate should be earth ground either to a ground junction box or
directly to an earth ground source (especially if the junction box is not metal).
2. Connect the cable to the rear of the reader at J1. Secure the shield drain lines to one of the
grounding screws in the IQ-400 enclosure.
3. Place mounting holes on the back of the reader over the latches on the mounting plate, and
then position the unit so that the cover is flush with the mounting plate.
4. Secure the unit to the mounting plate by inserting the special security fastener through the
hole in the bottom of the reader. Tighten it using the security driver.
IQ-400 Installation Manual
Page 13 of 100
33-10057-001-A
4.4.2 Grounding the Reader Mullion Mount
The reader may be attached to a glass or door mullion separator (either vertically or horizontally)
by using the Mullion Bracket Adapter Kits (04-10170-001 for horizontal mounting, or 04-10171001 for vertical mounting).
4.4.2.1 Procedure
1. At the IQ-400 end, secure the drain lines to one of the ESD grounding screws in the IQ-400
box. At the reader end, leave the drain line floating. It is recommended that the mullion
adapter be affixed to an earth grounded or to the incoming conduit.
2. Mount the reader to the J-box or mullion bracket.
Mullion
Mountin
g
Bracket
6-32 x 3/8 Flat
Head Screws,
4 places
Mullion
Bracket
Cover
Bracket should
be earth ground
Reader Mullion Mount Installation and Grounding
IQ-400 Installation Manual
Page 14 of 100
33-10057-001-A
5.0 Reader Connections
5.0.1. Reader Disconnect Resistors
If an external power supply and a reader disconnect feature is required, place a 470 Ohm – 1
Watt resistor (not supplied) at the reader.
Note:
For use in the following diagrams, resistors are shown connected to the boards.
However, for best operation, resistors should be placed at the reader.
IQ-400 Installation Manual
Page 15 of 100
33-10057-001-A
5.1 Reader Connections: BR-350 Readers: IQ-400 Board
IQ-400 Installation Manual
Page 16 of 100
33-10057-001-A
5.2 Reader Connections: BR-350 Readers: Expansion Board
IQ-400 Installation Manual
Page 17 of 100
33-10057-001-A
5.3 Reader Connections: BR-370 Readers: IQ-400 Board
IQ-400 Installation Manual
Page 18 of 100
33-10057-001-A
5.4 Reader Connections: BR-370 Readers: Expansion Board
IQ-400 Installation Manual
Page 19 of 100
33-10057-001-A
5.5 Reader Connections: PR233 MiniProx / PR-733/732: IQ-400 Board Option 1
IQ-400 Installation Manual
Page 20 of 100
33-10057-001-A
5.6 Reader Connections: PR233 MiniProx / PR-733/732: IQ-400 Board Option 2
IQ-400 Installation Manual
Page 21 of 100
33-10057-001-A
5.7 Reader Connections: PR-233 Miniprox/ PR733/ 732: Expansion Board –
Option 1
IQ-400 Installation Manual
Page 22 of 100
33-10057-001-A
5.8 Reader Connections: PR-233 Miniprox / PR733 / 732: Expansion Board
– Option 2
IQ-400 Installation Manual
Page 23 of 100
33-10057-001-A
5.9 Reader Connections: PR-234 / PRK-234 ProxPro / PR736 / PRK-736:
IQ-400 Board
IQ-400 Installation Manual
Page 24 of 100
33-10057-001-A
5.10 Reader Connections: PR-234 / PRK-234 ProxPro / PR736/ PRK-736:
Expansion Board
IQ-400 Installation Manual
Page 25 of 100
33-10057-001-A
5.11 Reader Connections: PR-235 MaxiProx / PR-735: IQ-400 Board
IQ-400 Installation Manual
Page 26 of 100
33-10057-001-A
5.12 Reader Connections: PR-235 MaxiProx / PR735: Expansion Board
IQ-400 Installation Manual
Page 27 of 100
33-10057-001-A
5.13 Reader Connections: Sensor Wiegand: IQ-400 Board
IQ-400 Installation Manual
Page 28 of 100
33-10057-001-A
5.14 Reader Connections: Sensor Wiegand: Expansion Board
IQ-400 Installation Manual
Page 29 of 100
33-10057-001-A
5.15 Reader Connections: VeriProx: IQ-400 Board
IQ-400 Installation Manual
Page 30 of 100
33-10057-001-A
5.16 Reader Connections: VeriProx: Expansion Board
IQ-400 Installation Manual
Page 31 of 100
33-10057-001-A
6.0 Wiring the Door(s)
Step 1.
When power is interrupted from the IQ-400, the door relay de-energizes and continuity
(conduction path) exists between the Common (Com.) and Normally Closed (N.C.)
relay contacts. Should this loss-of-power situation arise, it must be determined whether
the door(s) controlled by the IQ-400 will become unlocked (or a Fail-Safe environment),
or locked (or a Fail-Secure environment).
Step 2.
Refer to the two types of door hardware below and the circuit conditions that coincide
with the state of the locks.
Step 3.
Case A.
Door Strike hardware requires continuity to unlock (for strikes that require
power to lock, follow the outline given for maglocks). This is provided by a
closed circuit condition (Normally Closed [N.C.]).
Case B.
Door Strike hardware does NOT require continuity to lock (for strikes that
require power to lock, follow the outline given for maglocks). This is provided
by an open circuit condition (Normally Open [N.O.]).
Case C.
Magnetic lock hardware requires continuity to lock. This is provided by a
closed circuit condition (Normally Closed [N.C.]).
Case D.
Magnetic lock hardware does NOT require continuity to unlock.
This is provided by an open circuit condition (Normally Open [N.O.]).
For Fail-Safe operation, wire the appropriate door lock hardware to accommodate an
unlocked condition upon interruption of IQ-400 power. This is implemented by:
•
•
For door strikes, wire between the Common and Normally Closed Door Relay
contacts.
For Magnetic Locks, wire between the Common and Normally Open Door Relay
contacts.
For Fail-Secure operation, wire the appropriate door lock hardware to accommodate a
locked condition upon interruption of IQ-400 power. This is implemented by:
•
•
For door strikes, wire between the Common and Normally Open Door Relay
contacts.
For Magnetic Locks, wire between the Common and Normally Closed Door
Relay contacts.
NOTE For both conditions (Fail Safe and Fail Secure) it is presumed that Lock Power is
battery backed.
Step 4. Next page
IQ-400 Installation Manual
Page 32 of 100
33-10057-001-A
Step 4.
Program the quiescent (INACTIVE) state of the door output relay to provide a locked
door state. For Fail-Safe environments, the quiescent state of the door output relay
should be ENERGIZED. For Fail-Secure environments, it should be DE-ENERGIZED.
Consult the LiNC-NET Administrator Manual (P/N: 38-10049-001) Door Overview/Hardware
section for programming information.
Open Collector Output: Open collector outputs are designed to drive an external relay. This
technique can be used to control devices which exceed the relay capacity of those on board the
IQ-400. The open collector outputs are capable of 100 mA current @ 12VDC.
IQ-400 Installation Manual
Page 33 of 100
33-10057-001-A
6.1 Panel in a Fail-Safe Environment
IQ-400 Installation Manual
Page 34 of 100
33-10057-001-A
6.2 Panel in a Fail-Secure Environment
IQ-400 Installation Manual
Page 35 of 100
33-10057-001-A
6.3 Expansion Board Door Lock/Strike
IQ-400 Installation Manual
Page 36 of 100
33-10057-001-A
6.4 Expansion Board Open Collector
IQ-400 Installation Manual
Page 37 of 100
33-10057-001-A
6.5 Egress Sense for IQ-400 and Expansion Boards
IQ-400 Installation Manual
Page 38 of 100
33-10057-001-A
6.6 Door Sense for IQ-400 and Expansion Boards
NOTE
For UL Installations, the maximum number of alarm signals shall not exceed 1000.
IQ-400 Installation Manual
Page 39 of 100
33-10057-001-A
6.6.1 Using the Ten Discrete LEDs
Twenty-two LED’s, located across the lower section of the IQ-400 board, indicate the status of the
supervised door circuits. Also the unsupervised tamper, supervised egress inputs, and
supervised alarm inputs are annunciated in the LED’s as listed below:
IQ-400 Installation Manual
Page 40 of 100
33-10057-001-A
6.6.2 Expansion Board LED Arrays
4-Door Expansion Board (IQ-800)
8-Door Expansion Board (IQ-1200)
NOTE: Numbers in parentheses are the Sense Input Numbers. The “D” Numbers are the
corresponding LED’s assigned to reflect the current status of each individual
Sense Input (IQ-400 Firmware I4+07.010.02 series).
6.6.2.1 Status Chart For All IQ-400 Sense Inputs
OFF
ON
Flashes 2 times per second
Flashes 1 time per second
Flashes every ¼ second
IQ-400 Installation Manual
Circuit is normal/secure
Circuit is in an alarm condition
Fault condition. Open circuit
Fault condition. Short circuit.
Circuit is NOT calibrated and NOT functional.
Page 41 of 100
33-10057-001-A
6.7 Supervised Sense Inputs for P5 and P19 and Unsupervised Tamper at
P8
IQ-400 Installation Manual
Page 42 of 100
33-10057-001-A
IQ-400 Installation Manual
Page 43 of 100
33-10057-001-A
6.8 Expansion Board Supervised Door Senses and Supervised Request-toExit Sense Inputs
Install End-of-Line resistors at door switch/egress device (not at the IQ Panel end of the cable).
When door is closed, continuously exists across the common (COM) and normally closed (N.C.)
door switch contacts.
IQ-400 Installation Manual
Page 44 of 100
33-10057-001-A
6.9 Expansion Board Supervised Door Sense Locations
Install End-of-Line resistors at door switch/egress device (not at the IQ Panel end of
the cable).
When door is closed, continuously exists across the common (COM) and normally
closed (N.C.) door switch contacts.
IQ-400 Installation Manual
Page 45 of 100
33-10057-001-A
6.10 Installing Noise Suppression Devices
To install either an MOV or diode (or both) to suppress noise and avoid problems related to
spikes, follow the instructions below and refer to the diagrams on the following pages.
6.10.1 Procedure
The most effective location for a suppression device is at the source; in this case, at the door
strike.
1. Remove the strike-locking device and find the wire connector that attaches the lock wires to
the lock.
2. Install an MOV (Siemens S10K30 or equivalent) in parallel with the load. The MOV is a nonpolarized device and will work with both AC and DC locks. For further protection on DC units,
a reverse biased diode may be installed (We suggest types 1N4004 to 1N4007 be used) also
in parallel with the load.
NOTE Use an additional MOV if you experience further noise at the strike.
3. Note the wiring set-up of your particular system. Connections can be made either to the
“normally open” (fail secure) contact or to the “normally-closed” (fail-safe) configuration
whereby an isolation relay is used and a diode (or MOV) is added for noise suppression.
IQ-400 Installation Manual
Page 46 of 100
33-10057-001-A
7.0 Communicating with the IQ-400
The IQ-400 can communicate over a dialup MODEM, an RS232 or an RS485 serial direct
connection or LAN. In a multi-drop IQ-400 configuration, the IQ-400 MUST communicate via RS485 protocol.
7.1 Reset the IQ-400 Panel
You may elect to install the supervisory resistors at this time or optionally wait until after on-line
communication has been established to the LiNC-NET Host PC. Set dipswitches 1-8 (located at
SW1) to OFF position as it is etched on the IQ-400 PCB. Hit the reset switch at S1. This will
calibrate and reset data to default, all 14 of the supervised inputs on the IQ-400 PCB and the
supervised Door Senses on the 4/8-Door Cluster PCBs.
IQ-400 Installation Manual
Page 47 of 100
33-10057-001-A
7.2 Calibrating the IQ-400 Panel
Calibration Scan
Please check the LiNC-NET Calibrations Options
page on the LiNC-NET Administrator Manual.
SAM sense inputs are calibrated only by toggling switch #3 of SW-1 on each SAM PCB.
IQ-400 Installation Manual
Page 48 of 100
33-10057-001-A
7.3 Addressing Individual IQ-400s through the Dipswitch
7.3.1 Dipswitching the IQ-400 Address (1-111)
The dipswitch is located at SW1, on the right-side of the board. There are eight switches. For the
binary number one (1), flip the switch to the left. For zero (0), flip the switch to the right.
IQ-400 Installation Manual
Page 49 of 100
33-10057-001-A
7.3.2 Software Addressing the IQ-400 Panel (Panels 112-200) Direct Connect
If a user set up includes more than 111 panels, it is necessary to address the panel through the
LiNC-NET software as opposed to the Dipswitch on the panel itself. Every panel from 112 – 200
is manually set to 112, and then given a software address via LiNC-NET.
1. Set SW1 to address 112 on the IQ-400 panel
and press the S1 button. The Dipswitch setting
is: 5, 6, 7 = ON and 1, 2, 3, 4, 8 =OFF.
2. Open the ConFigUL program and define the
following:
• Connection Type (Direct Connect
or LAN)
• COM port
• Baud rate
3. Select the OPEN port button = Open Port OK
4. Enter Panel #1 into the “current panel
number” field.
5. Select the “Inquire” button = OK
6. Select the “Logon” button = OK
7. Enter the desired panel address from 112 – 200 in “New Panel number” window.
8. Select the “change number” button = OK
9. Select eh “Who’s there” button. The Inquire field will scan for the new panel address.
(Who’s There=200)
10. Select the “Logoff” button = OK then select “Close Port” and exit.
11. Start LiNC-NET and “add” the new panel ID number to your database.
NOTE
Switch #8 is used to determine if the IQ-400 communicates via either direct connect or
dial-up communications. Switch #8 is only used to determine if the connection is
Direct Connect or AutoDial.
The ON/OFF designation is in reference to the labels printed on the IQ-400
PCB. Not the switch itself!
IQ-400 Installation Manual
Page 50 of 100
33-10057-001-A
7.4 Setting MODEM or Direct Connect Configurations
PCSC supports the US Robotics 33.6/56K Sportster model for MODEM communication. It is
recommended that the MODEM be powered up via an U.P.S. (Uninterruptible Power Supply).
To set up the IQ-400 for MODEM communication, configure the Dipswitch settings at SW1, as
follows:
Example: MODEM connection (IQ-400, panel address is #1)
SW1
On 1 Off 0
Set # 1 to ON
(left), 2 through
7 to OFF
(right). Set # 8
to ON (left).
1
2
3
4
5
6
7
8
Set the configuration and press the Reset button at S1. After the
sequence of LEDs displays, set the IQ-400 ID number (see DIP
Switching the IQ-400 Number). On the back of the US Robotics
modem, locate the DIP switch. Set 1, 5 and 6 in the up position
and 2, 3, 4, 7 and 8 in the down position.
NOTE AT SW1, switch #8 must remain in the ON position (left) for MODEM
communication.
To set up the IQ-400 for direct connect communication (default), configure the Dipswitch
settings at SW1, as follows:
Example: Direct connection (IQ-400, Panel address is #1)
SW1
On 1 Off 0
1
2
3
4
5
6
7
8
Set # 1 to
ON (left), 2
through 8
to OFF
(right).
Set the configuration and press the Reset button at S1. After the
reset, set the IQ-400 ID number (see DIP Switching the IQ-400
Number).
NOTE At SW1, switch #8 must remain in the OFF position (right) for Direct
Connect communication.
To communicate from an IQ-400 to the MODEM, two cables must be fabricated: one from the
MODEM to the IQ-400 and another for the PC host to the MODEM. See the diagrams under
Cable Requirements.
NOTE The ON/OFF designation is in reference to the labels printed on the IQ400 PCB. Not the switch itself!
IQ-400 Installation Manual
Page 51 of 100
33-10057-001-A
7.4.1 Ensuring Proper Configuration of the MODEM
To ensure that the MODEM retains the set configuration, the user should utilize HyperTerminal at
the Host PC. The HyperTerminal program will set the configuration in the MODEM for constant
uninterrupted use with the IQ-400. In the following procedure, the Init String will be written into the
NOVRAM and therefore a power loss to the MODEM ONLY will not result in a continuous loop.
•
Set switches 1, 5, 6, and 7 in the U.S Robotics Sportster MODEM (14.4K, 28.8, 33.6, or
56K) to Up. All other switches should be Down.
•
Connect the MODEM to the PC using a standard PC to MODEM cable.
•
From the PC (Win95/98/NT) access HyperTerminal by entering the following commands:
1. Click on Start: Programs: Accessories, and then, HyperTerminal. The
Connection Description dialog box will now appear.
2. Type in a name for the connection (for example: MODEM TEST). Click on a
corresponding icon from the list. Click on the OK button.
3. The Connect To dialog box will now appear. The proper communications port used
to communicate to the external MODEM is now selected within the Connect Using
field (for example: COM2). Click on the OK button.
4. The COM# Properties dialog box will now appear. Select 9600 in the bits per
second field. Select 8 in the Data Bits field, None in the Parity field, 1 in the Stop
Bits field, and Hardware in the Flow control field. Click on the OK button. The
screen will now clear and the cursor will be at the top left corner of the
HyperTerminal window. Type ATV1 E1 and press Enter. The MODEM will
respond with OK.
5. Type ATI3 and press Enter to display the type of MODEM connected, followed by
OK.
6. Type ATI4 and press Enter to display the MODEM’s current settings, followed by
OK.
7. Type ATI5 and press Enter to display the MODEM’s NVRAM settings, including
any stored telephone numbers, followed by OK.
8. Type ATEVQHSØ=1X&DØ and press Enter. The MODEM will respond by
changing the A in the previous String to a Ø (zero).
9. Type AT&WØYØ and press Enter. No visual indication will be displayed as the
MODEM was configured in the previous step to use Numeric Result Codes.
10. Type ATZ and press Enter. As in the previous step, no visual indication will be
displayed.
11. Click on File, then Save, to save the configuration file.
12. Click on File, Exit, then Yes, to disconnect from the MODEM and exit
HyperTerminal.
13. Power down the MODEM and turn switch 1, 5, and 6 up. All others should be
down. Connect the MODEM to the IQ-400. Perform functional testing.
IQ-400 Installation Manual
Page 52 of 100
33-10057-001-A
7.4.2 Establishing a Proper Connection with a MODEM Cable
To communicate from an IQ-400 to a MODEM, two cables must be fabricated: one from the
MODEM to the IQ-400 and another for the PC host to the MODEM. Cabling should be 22 AWG,
9-conductor, UL2576 and up to 6 feet in length.
NOTE: PCSC performs Autodial Testing with US Robotics Sportster (Internal
and External) 33.6 Fax Modems.
See the following diagrams:
IQ-400 Installation Manual
Page 53 of 100
33-10057-001-A
7.5 Changing the Baud Rate
1. Request the IQ-400 off-line in the Define Panel Online Status screen in the LiNC-NET
software.
2. Change the baud rate in the Host Computer Setup menu in the LiNC-NET Software.
3. Log off and back onto the system.
4. Set the switch (SW1) setting for the Baud rate and press the S1 Reset button. (Refer to page
58).
5. Change the SW1 switch setting back to the IQ-400 number.
6. Request the IQ-400 on-line in the Define Micro-LPM status screen in the LiNC-NET software.
NOTE
Presently the IQ-400 only supports communication at 9600 BPS.
IQ-400 Installation Manual
Page 54 of 100
33-10057-001-A
IQ-400 Installation Manual
Page 55 of 100
33-10057-001-A
7.6 Direct Connecting with One IQ-400
The PC Host is connected to the IQ-400 by means of a cable designed for either RS-485 or RS232 communication. The following diagrams illustrate the RS-485 and RS-232 DB9 or DB25
connectors options available.
Wiring Diagram- IQ-400 to PC, RS-485 Connector
w/ DB25 Connector
IQ-400 Installation Manual
w/ DB9 Connector
Page 56 of 100
33-10057-001-A
IQ-400 to PC, RS-485 w/ DB25
Connector, Optically Isolated,
PCSC P/N 04-10322-101
IQ-400 to PC, RS-485 w/ DB9
Connector, Optically Isolated,
PCSC P/N 04-10322-001
PC
IQ-400, P3
1
+485/TX 2
SHD 3
-485/RX 4
Com/GND
Customer-fabricated cable may extend to 4,000ft.
1
7
2
3
4
5
14
16
Shield Gnd
Signal Gnd
TxA
RxA
IQ-400, P3
Com /Gnd
+485/TX
SHD
-485/RX
RTS
PC
TxB
RxB
Page 57 of 100
1
2
3
9
5
Signal Ground
CTS
25-pin female connector, DB-25
IQ-400 Installation Manual
1
2
3
4
RD(A)
TD(B)
TD(A)
RD(B)
Sig Gnd
9-pin female
connector, DB-9
Shield Ground
Connect to PC earth ground
Customer-fabricated cable may extend to 4,000ft.
33-10057-001-A
7.6.1 Wiring Diagram- IQ-400 to PC, RS-232 w/DB9 Connector
PCSC P/N: 04-10318-101
7.6.2 Wiring Diagram – IQ 400 to PC, RS -232 w/ DB25 Connector
PCSC P/N: 04-10318-001
IQ-400 Installation Manual
Page 58 of 100
33-10057-001-A
7.7 RS-232 Cable Connections
IQ-400 to PC, Cable RS-232
w/DB25 Connector
PCSC p/n 04-10318-101
IQ-400 to PC Cable RS-232
w/DB9 Connector
PCSC p/n 04-10318-001
NOTE: For UL 1076 requirements, the RS-232 cable shall not extend beyond 20 ft., and the
cable shall stay within the same room.
IQ-400 Installation Manual
Page 59 of 100
33-10057-001-A
7.8 Communicating with Multiple IQ-400s (via RS-485)
Once the PC host is connected to one IQ-400, the next IQ-400 can be connected by wiring from
P3 from the first IQ-400 to P4 in the next IQ-400. This format can be repeated in up to 16 IQ400s. In addition, any combination of MicroLPMs and IQ-400s can be configured up to the 16
total limit on a single RS485 channel. LiNC-NET supports up to 4 channels (total of 64 IQ400/MicroLPMs). See the next page for the IQ-400 to MicroLPM wiring connection.
7.8.1 Wiring Diagram of Multiple IQ-400s
IQ-400 Installation Manual
Page 60 of 100
33-10057-001-A
7.8.2 Wiring Diagram of Multiple IQ-400s and MicroLPMs
IQ-400 Installation Manual
Page 61 of 100
33-10057-001-A
7.9 Real Time Serial Printing with the IQ-400
To print from an IQ-400, a cable must be fabricated: a 9-pin female connector at the IQ-400-end
to either a 9-pin or 25-pin male connector at the printer end. Cabling should be 22 AWG, 2twisted pair, and up to 6 feet in length. See the following diagrams. The baud rate for the printer is
9600 bits per second at the IQ-400. Connect the IQ-400 end of the cable to P7.
Cable Configuration for Capturing Real Time Transactions to PC in
HyperTerminal
IQ-400 Installation Manual
Page 62 of 100
33-10057-001-A
8.0 Status Lights and Dealing with Communication Errors
8.1 Status Lights
The IQ-400 circuit board has multiple LEDs. The status of the LED defines a certain activity or
phase of IQ-400 functions. Card processing and door sense status is also indicated by the LEDs.
IQ-400 Installation Manual
Page 63 of 100
33-10057-001-A
8.2 Communication Errors
Message at the PC
What to Do
IQ-400 is not responsive
Verify the following:
1. The red DC Power Indicator LED (D2) is ON.
2. Verify that the ID number corresponds to the IQ-400
at the PC. (Check settings of switches at SW1).
3. Check cabling. (RS232/MODEM/RS485/Terminal
Server).
4. Remove the Battery for 5 minutes. Reinsert battery
and restart IQ-400 panel.
8.2.1 LED Fatal Error Display Codes
(Please CALL your PCSC representative.)
E1
E2
E4
E5
E7
ED
EE
EF
ROM error detected- Probable PCB failure.
RAM error detected- Probable PCB failure. Verify that the IC at U108 is seated
properly.
Packet addressing error- IQ-400 failure
Packet queuing error- IQ-400 failure.
Terminal number configuration error- Readdress IQ-400.
Database invalid- RESET and configure IQ-400 address
Stray jump- Probable IQ-400 PCB failure.
Execution of int vector- Probable IQ-400 PCB failure.
IQ-400 Installation Manual
Page 64 of 100
33-10057-001-A
8.2.2 Error Codes
The seven-segment LEDs, D49 and D50, will indicate certain errors that can occur when
processing cards. They also can communicate “fatal” errors that could occur. The following chart
describes different error codes that are displayed by the seven-segment LEDs:
D Warning Error
Display Codes
Possible Problem
What to Do
C0 Card Error:
Parity check fail
Clean reader head and re-try
C1 Card Error:
LRC check failed
C5 Card Error:
data length mismatch
CC Card Error:
data conversion
CE Card Error:
end-code not found
CF Card Error:
facility code
EC Hardware
Configuration error
Bad Card or dirty reader
head
Bad Card or dirty reader
head
Check for correct format
type
Check for correct format
type
Bad card or dirty reader
head
The site code is invalid for
this site
The IQ-400 is not
configured correctly
IQ-400 Installation Manual
Page 65 of 100
Clean reader head and re-try
Verify that the correct reader
technology is specified
Verify that the correct reader
technology is specified
Clean reader head and re-try
Load correct facility code or
check cards
In LiNC-NET for Windows,
select the Panel Setup icon
and the Hardware file-tab to
verify that the extension
adapters are selected for this
IQ-400.
33-10057-001-A
8.3 Control Counters and Sense Input Numbers for Output Control PCB
IQ-400 Installation Manual
Page 66 of 100
33-10057-001-A
IQ-400 Installation Manual
Page 67 of 100
33-10057-001-A
8.4 Proper Setting of SAM 1 and SAM 2
In a system that uses SAM 1 as a stand-alone, the W1 switch must be set to LOW
(Pins 2-3).
In a system that uses both SAM 1 and SAM 2 together, SAM 1 needs to be set to LOW
(Pins 2-3) and SAM 2 needs to be set to HIGH (Pins 1-2).
IQ-400 Installation Manual
Page 68 of 100
33-10057-001-A
8.5 IQ Systems Upgrades and Capacities
Model
Readers
Supervised
Reader
Detect
Door
Relay
Outputs
Auxiliary
Relay
Outputs
External Shunt/Local
Alarm Transistor
Outputs
Auxiliary
Transistor
Outputs
Supervised
Door Sense
Inputs
Supervised
Egress
Sense Inputs
Unsupervised
Egress
Sense Inputs
Supervised
Auxiliary
Sense Inputs
Unsupervised
Tamper
Sense Inputs
Unsupervised
Auxiliary
Sense Inputs
IQ200
IQ200/OUT
IQ200/ALM
IQ200/SAM
IQ200/SAM2
IQ400
IQ400/OUT
IQ400/ALM
IQ400/SAM
IQ400/SAM2
IQ600
IQ600/OUT
IQ600/ALM
IQ600/SAM
IQ600/SAM2
IQ1000
IQ1000/OUT
IQ1000/ALM
IQ1000/SAM
IQ1000/SAM2
IQ1200
IQ800
IQ800/OUT
IQ800/ALM
IQ800/SAM
IQ800/SM2
2
2
2
2
2
4
4
4
4
4
6
6
6
6
6
10
10
10
10
10
12
8
8
8
8
8
2
2
2
2
2
4
4
4
4
4
6
6
6
6
6
10
10
10
10
10
12
8
8
8
8
8
2
2
2
2
2
4
4
4
4
4
6
6
6
6
6
10
10
10
10
10
12
8
8
8
8
8
0
16
0
0
0
0
16
0
0
0
0
16
0
0
0
0
16
0
0
0
0
0
16
0
0
0
2
2
2
2
2
4
4
4
4
4
6
6
6
6
6
10
10
10
10
10
12
8
8
8
8
8
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
4
4
4
4
4
6
6
6
6
6
10
10
10
10
10
12
8
8
8
8
8
2
2
2
2
2
4
4
4
4
4
6
6
6
6
6
10
10
10
10
10
12
8
8
8
8
8
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
5
5
5
5
5
5
5
5
13
21
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
16
16
0
0
0
16
16
0
0
0
16
16
0
0
0
16
16
0
0
0
0
16
16
0
0
*Form C Dry Contact- Relay comprised of normally open (N.O.), normally closed (N.C.) and common (COM) contacts which are available for
connection. Contacts are rated at two amps, 12/24 VDC continuous power.
IQ-400 Installation Manual
Page 69 of 100
33-10057-001-A
8.6 RS-232/485 Terminal Servers
IQ-400 Installation Manual
Page 70 of 100
33-10057-001-A
8.7 RS-232-485/422 Converters: Printed Circuit Board Layout
IQ-400 Installation Manual
Page 71 of 100
33-10057-001-A
8.8 User Selectable Options
Underlined settings are for LiNC-NET User -Selectable Options.
An asterisk (*) designates the factory preset jumper settings.
XWIA
XWIB
W8
W15
W5
W9
W17
W16
S1
S2
S3
DCE*
DTE
A-B
B-C*
A-B
B-C*
A-B
B-C*
4-wire
2-wire
RTS/CD enabled
Data enabled (Maximum speed is 64K)
RTS/CTS* delay (normal)
RTS/CTS/CD delay (CTS inhibited if CD is present when RTS is raised.
RTS/CTS delay (The time before the RS-485 driver is enabled and CTS
is asserted after RTS is asserted. The RS-485 driver is always enabled.)
A
30 msec
B
10 msec
0 msec
C*
D
ON
When W15 is in the B-C (Data Enabled) position, this is the time the RS485 driver remains enabled after a low-to-high transition on the DATA line
to prevent disabling the driver in the middle of a character.
A
70 msec
B
7 msec
C
2 msec
D
0.7 msec
0.15 msec
E*
Turnaround delay (When W8 is in the B-C [2 wire] position, this is the time
after the driver is disabled and before the receiver is enabled.)
A
0 msec
msec
B*
C*
msec
D
5 msec
E
35 msec
NOTE If the converter is configured Data Enabled (W15, position B-C) and 2-wire (W8,
position B-C), then delays from W17 and W16 are cumulative.
OU
Normal
T*
IN
Loopback
OF
RS-485 Receiver Unterminated
F*
ON
RS-485 Terminated
OFF*
Line Bias Off
ON
TB1
Line Bias On (The Carrier Detect light will come on. Default is +5 volts.)
4-wire terminal block
1……….Rx……….B+
2……….Rx……….A3……….Tx……….B+
4……….Tx……….A-
W19
Plug P2, pin 2
Plug P2, pin 4
(Open) - Not jumpered.
IQ-400 Installation Manual
Page 72 of 100
33-10057-001-A
8.9 Point Definitions
8.9.1 Sense Inputs
8.9.1.1 IQ-400 Point Definitions – Sense Inputs
IQ (P/N 03-10111-201)
S1 through S2 are located
on the IQ PCB.
Designation
S1
S2
S3
S4
Location
P8, Reader a
P9, Reader b
P10, Reader c
P11, Reader d
IQ (P/N 03-10111-201)
S13 through S23
are located on
the IQ-400.
Designation
S13
S14
S16
S17
S18
S19
S20
S21
S22
S23
Location
P18, pin 1, 2
P19, pin 1, 2
P12, pin 3, 4
P12, pin 1, 2
P13, pin 3, 4
P13, pin 1, 2
P14, pin 3, 4
P14, pin 1, 2
P15, pin 3, 4
P15, pin 1, 2
IQ/OUT/ALM*
Designation
S56
S57
S58
S59
S60
S61
S62
S63
S64
S65
S66
S67
S68
S69
S70
S71
Location
P1, pin 7, 8
P1, pin 5, 6
P1, pin 3, 4
P1, pin 1, 2
P2, pin 7, 8
P2, pin 5, 6
P2, pin 3, 4
P2, pin 1, 2
P3, pin 7, 8
P3, pin 5, 6
P3, pin 3, 4
P3, pin 1, 2
P4, pin 7, 8
P4, pin 5, 6
P4, pin 3, 4
P4, pin 1, 2
*Sense inputs 56 through 71 are located on the
ALM PCB (P/N 03-10032-301) in an IQ/ALM.
IQ (P/N 03-10111-201)
S120 through
S123 are
located on the
IQ-400
Designation
S120
S121
S122
S123
Location
P5, pin 1, 2
P5, pin 3, 4
P6, pin 1, 2
P6, pin 3, 4
The same sense inputs are also used in the
OUTPUT PCB (P/N 03-10032-201F) in an
IQ/OUT.
st
IQ SAM/1 SAM Board (P/N 03-10056-201)
1st SAM PCB is
used in:
IQ-400/SAM
IQ-400/SAM2
IQ-800/SAM
IQ-400/SAM2
nd
IQ SAM/2
Designation
S40
S41
S42
S43
S44
S45
S46
S47
Location
P2, pin 1, 2,
P2, pin 3, 4
P3, pin 1, 2
P3, pin 3, 4
P4, pin 1, 2
P4, pin 3, 4
P5, pin 1, 2
P5, pin 3, 4
SAM Board (P/N 03-10056-201)
2nd SAM PCB is
used in:
IQ-800/SAM
IQ-800/SAM2
Designation
S48
S49
S50
S51
S52
S53
S54
S55
IQ-400 Installation Manual
Location
P2, pin 1, 2,
P2, pin 3, 4
P3, pin 1, 2
P3, pin 3, 4
P4, pin 1, 2
P4, pin 3, 4
P5, pin 1, 2
P5, pin 3, 4
Page 73 of 100
33-10057-001-A
8.9.1.2 IQ-800 Series Point Definitions – Sense Inputs
4-Reader Cluster Board (P/N 03-10102-301)
S3 through S6 are
located
on the S8 are
S5 through
IQlocated
4 PCB. on the 4-
Reader Expansion
PCB.
Designation
S5
S6
S7
S8
Location
P10, Reader e
P16, Reader f
P12, Reader g
P14, Reader h
IQ/OUT/ALM*
Designation
S56
S57
S58
S59
S60
S61
S62
S63
S64
S65
S66
S67
S68
S69
S70
S71
4-Reader Expansion Board (P/N 03-10102-301)
S24 through S31
are located on the
4-Reader
Expansion PCB.
Designation
S24
S25
S26
S27
S28
S29
S30
S31
Location
P11, pin 3, 4
P11, pin 1, 2
P17, pin 3, 4
P17, pin 1, 2
P13, pin 3, 4
P13, pin 1, 2
P15, pin 3, 4
P15, pin 1, 2
st
IQ SAM/1 SAM Board (P/N 03-10056-201)
1st SAM PCB is
used in:
IQ-400 SAM
IQ-400 SAM2
IQ-800 SAM
IQ-800 SAM2
nd
IQ SAM/2
Designation
S40
S41
S42
S43
S44
S45
S46
S47
Location
P2, pin 1, 2,
P2, pin 3, 4
P3, pin 1, 2
P3, pin 3, 4
P4, pin 1, 2
P4, pin 3, 4
P5, pin 1, 2
P5, pin 3, 4
Location
P1, pin 7, 8
P1, pin 5, 6
P1, pin 3, 4
P1, pin 1, 2
P2, pin 7, 8
P2, pin 5, 6
P2, pin 3, 4
P2, pin 1, 2
P3, pin 7, 8
P3, pin 5, 6
P3, pin 3, 4
P3, pin 1, 2
P4, pin 7, 8
P4, pin 5, 6
P4, pin 3, 4
P4, pin 1, 2
*Sense inputs 56 through 71 are located on the ALM
PCB (P/N 03-10032-301) in an IQ/ALM.
The same sense inputs are also used in the OUTPUT
PCB (P/N 03-10032-201) in an IQ/OUT.
SAM Board (P/N 03-10056-201)
2nd SAM PCB is
used in:
IQ-400 SAM2
IQ-800 SAM2
Designation
S48
S49
S50
S51
S52
S53
S54
S55
IQ-400 Installation Manual
Location
P2, pin 1, 2,
P2, pin 3, 4
P3, pin 1, 2
P3, pin 3, 4
P4, pin 1, 2
P4, pin 3, 4
P5, pin 1, 2
P5, pin 3, 4
Page 74 of 100
33-10057-001-A
8.9.1.3 IQ-1200 Series Point Definitions – Sense Inputs
8-Reader Expansion Board (P/N 03-10102-201E)
S3 through
S10 are
located on
the
IQ 8 PCB.
Designation
S5
S6
S7
S8
S9
S10
S11
S12
Location
P2, Reader e
P8, Reader f
P4, Reader g
P6, Reader h
P10, Reader i
P16, Reader j
P12, Reader k
P14, Reader l
8-Reader Expansion Board (P/N 03-10102-201E
S24 through S39
are located on
the 8-Reader
Expansion
Board.
Designation
S24
S25
S26
S27
S28
S29
S30
S31
S32
S33
S34
S35
S36
S37
S38
S39
IQ-400 Installation Manual
Location
P3, pin 3, 4
P3, pin 1, 2
P9, pin 3, 4
P9, pin 1, 2
P5, pin 3, 4
P5, pin 1, 2
P7, pin 3, 4
P7, pin 1, 2
P11, pin 3, 4
P11, pin 1, 2
P17, pin 3, 4
P17, pin 1, 2
P13, pin 3, 4
P13, pin 1, 2
P15, pin 3, 4
P15, pin 1, 2
Page 75 of 100
33-10057-001-A
8.9.2 Outputs
8.9.2.1 IQ-400 Series Point Definitions – Outputs
IQ-400 (P/N: 03-10111-201
IQ Form C
Relay
01
02
03
04
Connector
Common
Normally
Open
Pin 6
Pin 6
Pin 6
Pin 6
Normally
Closed
Pin 5
Pin 5
Pin 5
Pin 5
P12
P13
P14
P15
Pin 7
Pin 7
Pin 7
Pin 7
IQ Open
Collector
Connector
+12VDC
Output
13
14
15
16
P12
P13
P14
P15
Pin 9
Pin 9
Pin 9
Pin 9
Open
Collector
Output
Pin 8
Pin 8
Pin 8
Pin 8
IQ-400/OUT (P/N: 03-1032-201F)
IQ
OUT/ALM
Form C
Relay
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Common
Normally
Closed
Connector
Common
Normally
Open
Pin 8
Pin 6
Pin 4
Pin 2
Pin 8
Pin 6
Pin 4
Pin 2
Pin 8
Pin 6
Pin 4
Pin 2
Pin 8
Pin 6
Pin 4
Pin 2
Pin 7
Pin 5
Pin 3
Pin 1
Pin 7
Pin 5
Pin 3
Pin 1
Pin 7
Pin 5
Pin 3
Pin 1
Pin 7
Pin 5
Pin 3
Pin 1
P9
P9
P9
P9
P10
P10
P10
P10
P11
P11
P11
P11
P12
P12
P12
P12
Pin 8
Pin 6
Pin 4
Pin 2
Pin 8
Pin 6
Pin 4
Pin 2
Pin 8
Pin 6
Pin 4
Pin 2
Pin 8
Pin 6
Pin 4
Pin 2
Pin 7
Pin 5
Pin 3
Pin 1
Pin 7
Pin 5
Pin 3
Pin 1
Pin 7
Pin 5
Pin 3
Pin 1
Pin 7
Pin 5
Pin 3
Pin 1
Connector
P5
P5
P5
P5
P6
P6
P6
P6
P7
P7
P7
P7
P8
P8
P8
P8
IQ-400 Installation Manual
Page 76 of 100
33-10057-001-A
8.9.2.2 IQ-800 Series Point Definitions – Outputs
4-Reader Expansion PCB (P/N: 03-10102-301E)
IQ Form C
Relay
05
06
07
08
Connector
Common
Normally
Open
Pin 6
Pin 6
Pin 6
Pin 6
Normally
Closed
Pin 5
Pin 5
Pin 5
Pin 5
P11
P17
P13
P15
Pin 7
Pin 7
Pin 7
Pin 7
IQ Open
Collector
Connector
+12VDC
Output
17
18
19
20
P11
P17
P13
P15
Pin 9
Pin 9
Pin 9
Pin 9
Open
Collector
Output
Pin 8
Pin 8
Pin 8
Pin 8
IQ-800/OUT (P/N: 03-10032-201F)
IQ
OUT/ALM
Form C
Relay
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Connector
Common
Normally
Closed
Connector
Common
Normally
Open
P5
P5
P5
P5
P6
P6
P6
P6
P7
P7
P7
P7
P8
P8
P8
P8
Pin 8
Pin 6
Pin 4
Pin 2
Pin 8
Pin 6
Pin 4
Pin 2
Pin 8
Pin 6
Pin 4
Pin 2
Pin 8
Pin 6
Pin 4
Pin 2
Pin 7
Pin 5
Pin 3
Pin 1
Pin 7
Pin 5
Pin 3
Pin 1
Pin 7
Pin 5
Pin 3
Pin 1
Pin 7
Pin 5
Pin 3
Pin 1
P9
P9
P9
P9
P10
P10
P10
P10
P11
P11
P11
P11
P12
P12
P12
P12
Pin 8
Pin 6
Pin 4
Pin 2
Pin 8
Pin 6
Pin 4
Pin 2
Pin 8
Pin 6
Pin 4
Pin 2
Pin 8
Pin 6
Pin 4
Pin 2
Pin 7
Pin 5
Pin 3
Pin 1
Pin 7
Pin 5
Pin 3
Pin 1
Pin 7
Pin 5
Pin 3
Pin 1
Pin 7
Pin 5
Pin 3
Pin 1
IQ-400 Installation Manual
Page 77 of 100
33-10057-001-A
8.9.2.3 IQ-1200 Series Point Definitions – Outputs
8-Reader Expansion PCB (P/N: 03-10102-201E)
IQ Form C
Relay
05
06
07
08
09
10
11
12
Connector
Common
P3
P9
P5
P7
P11
P17
P13
P15
Pin 7
Pin 7
Pin 7
Pin 7
Pin 7
Pin 7
Pin 7
Pin 7
IQ Open
Collector
Connector
+12VDC
Output
17
18
19
20
21
22
23
24
P3
P9
P5
P7
P11
P17
P13
P15
Pin 9
Pin 9
Pin 9
Pin 9
Pin 9
Pin 9
Pin 9
Pin 9
IQ-400 Installation Manual
Normally
Open
Pin 6
Pin 6
Pin 6
Pin 6
Pin 6
Pin 6
Pin 6
Pin 6
Normally
Closed
Pin 5
Pin 5
Pin 5
Pin 5
Pin 5
Pin 5
Pin 5
Pin 5
Page 78 of 100
Open
Collector
Output
Pin 8
Pin 8
Pin 8
Pin 8
Pin 8
Pin 8
Pin 8
Pin 8
33-10057-001-A
9.0 Appendix A - IQ-400 Specifications
9.1 IQ-400 Features
2 Auxiliary Powered Outputs (cc# 89, 90)
1 Unsupervised Tamper Sense Input (S13)
4 Reader Ports:
-5-wire Wiegand interface
-4-wire PCSC Proprietary
4 Form C Door Strike Outputs
(2 Amps @ 24 VDC)
(cc# 1, 2, 3 and 4) 2 Amps continuous power @12/24 VDC
4 Door Left Open Outputs (or 4 External Shunt Options) (cc# 13, 14, 15 and 16)
4 Supervised Door Senses (S17, 19, 21, 23)
5 User Defined Sense Inputs (S14, S120, S121, S122, S123)
4 Request to Exit Inputs (S16, 18, 20, 21)
Battery Backed Clock Calendar
Flash RAM 128K standard (up to 256K)
Battery Backed RAM 256K standard (up to 512K)
LEDs for:
Power, alarm, on-line diagnostics
Reader Data [Error code, door status]
Tamper detect (S13)
Type of Communications:
RS-232 and RS-485
Ethernet/onboard
Autodial MODEM or (optional On-Board Modem)
9.1.1 System Capacities
Cardholder Capacity:
Time Periods:
Holiday Time Periods:
Holiday List:
History Transactions:
8,000 (20,000 w/Memory Expansion)
32
32
366 Days (Leap Year)
4,000 regardless of memory size
9.1.2 Spare Parts- IQ-400 PCB
Part Number
81-09009
78-01001
83-02082
83-02083
83-02084
83-02085
83-02086
79-03022
83-02007
IQ-400 Installation Manual
Description
3V Lithium Battery
4A 250V 1/4 x 1/4, 3AG Fuse
5-pin Plug Connector
2-pin Plug Connector
4-pin Plug Connector
3-pin Plug Connector
9-pin Plug Connector
DPST Relay
Jump Connector
Page 79 of 100
Designation
BT1
F1
P8, P9, P10, P11
P1, P16, P17, P18, P19
P3, P4, P5, P6
P2
P12, P13, P14, P15
K1, K2, K3, K4
For W1 – W9
33-10057-001-A
9.2 IQ 4-Reader Expansion Module (P/N: 03-10102-301E)
The IQ-400 4-reader system can be expanded to an 8-reader system by installing the 4-Reader
Expansion Module. The circuit board (Part # 03-10102-10X) can be mounted below the circuit
board in the larger enclosures available from PCSC. Once mounted, the circuit board is
connected to the IQ-400 by installing a 50-pin ribbon expansion cable from P1 on the 4-reader
module to J1 on the IQ-400.
The 4-Reader Expansion Module allows the user to connect up to 4 additional readers to the IQ400. Each of the reader interfaces support either a PCSC proprietary reader (4-wire interface), or
a Wiegand reader (5-wire interface). The Expansion Module also provides an additional 4
interfaces for each of the readers and the associated doors. These include the following:
•
•
•
•
•
•
Multilevel door sense inputs (Supervised door sense inputs)
Reader Present inputs (Reader connected/disconnected)
Request to Exit inputs (Unsupervised egress inputs)
Relay contacts for door control outputs (Form C dry contacts rated for 2.0 Amps @
12/24VDC continuous power)
Door shunt outputs (Open Collector output rated for +12 VDC @ 100mA)
Door Shunt/Local Alarm
9.2.1 Power Supply
The 4-reader Expansion Module requires +5VDC for all logic. Relays, output drivers, etc. require
a +12VDC supply. The +5VDC and +12VDC is provided to the module via the 50-pin expansion
cable, which connects plug P1 of the 4-door cluster PCB (P/N 03-10102-301E) to plug J1 of the
IQ-400 board, (P/N 03-10111-201).
9.2.2 Door Sense LEDs
4 LEDs located at D17, D18, D19, and D20 indicate the status of the Door circuits. Resistors
must be installed at the door contacts, the switches in place, door closed (normal state), and the
lines calibrated, in order for the supervised inputs to function. See Step 4 for installation and
calibration procedure.
LED Status Chart (for IQ-400 firmware I4+07.010.02 series):
•
•
•
•
Sense Input #25 LED is D17
Sense Input #27 LED is D18
Sense Input #29 LED is D19
Sense Input #31 LED is D20
NOTE LEDs D21-D24 are not used in the IQ-800.
OFF
ON
Blinks once every 2 seconds
Blinks 1 time/second
Blinks 4 times/second
IQ-400 Installation Manual
Circuit is in normal/secure state
Circuit is in an alarm condition state
Fault condition. Open circuit state
Fault condition. Short circuit state
Circuit is NOT calibrated and NOT in a
functional state
Page 80 of 100
33-10057-001-A
9.3 IQ-800 Features (IQ-400 plus 4-Reader Expansion Module)
9.3.1 Two Auxiliary (Powered) Outputs (cc# 89, 90)
8 Reader Ports:
(Wiegand electrical interface for PCSC and OEM card readers) (Readers a-h)
8 Form C Door Strike Outputs (2.0 amps @ 12/24 VDC continuous power)
8 Door Left Open Outputs (or 8 External Shunt Options)
8 Supervised Door Senses (17, 19, 21, 23, 25, 27, 29, 31)
5 Supervised User-Defined (Auxiliary) Sense Inputs (S14, S120, S121, S122, S123)
8 Supervised Request to Exit Inputs (16, 18, 20, 22, 24, 26, 28, 30)
Battery Backed Clock Calendar
Flash RAM 128K standard (up to 256K)
Battery-Backed RAM 256K standard (up to 512K)
LEDs for:
Power, alarm, on-line diagnostics Reader Data [Error code, Door Status]
Unsupervised Tamper detect (S13)
9.3.2 System Capacities
Cardholder Capacity:
Time Periods:
Holiday Time Periods:
Holiday List:
History Transactions:
Enclosure Dimensions:
Weight:
Power:
Draw:
Temperature:
Communications:
8,000 (20,000 w/ Memory Expansion)
32
32
366 Days (Leap Year)
4,000 regardless of memory size
18”H x 11.5”W x 6”D
(45.7cm x 29.2cm x 15.2cm)
38 lbs. (17.3kg)
12VDC
3 amp @ 12VDC
32°F to 115°F (0°C to 46°C)
RS485 standard
RS232 standard
External MODEM or (optional On-Board Modem)
Ethernet optional
9.3.3 Spare Parts- 4-Reader Expansion Board (P/N: 03-10102-301E)
Part Number
Description
Designation
83-02082
83-02086
79-03022
83-2007
5-pin Plug Connector
9-pin Plug Connector
DPST Relay
Jump Connector
P10, P12, P14, P16
P11, P13, P15, P17
K5- K8
W1-W3, W5-W6, W11-W15
IQ-400 Installation Manual
Page 81 of 100
33-10057-001-A
9.4 IQ 8-Reader Expansion Module (P/N: 03-10102-201E)
The IQ-400 4-reader system can be expanded to a 12-reader system by installing the 8-Reader
Expansion Module. The 8-Reader Expansion board can be mounted below the IQ-400 in the
larger enclosures available from PCSC. Once mounted, the 8-Reader Expansion board is
connected to the IQ-400 by installing a 50-pin ribbon expansion cable from P1 on the 8-reader
Expansion board to J1 on the IQ-400.
The 8-Reader expansion board allows the user to connect up to 8 additional readers to the IQ400. Each of the reader interfaces support either a PCSC proprietary reader (4-wire interface), or
a Wiegand reader (5-wire interface). The Expansion board also provides 8 additional interfaces
for each of the readers and the associated doors. These include the following:
•
•
•
•
•
Multilevel Door Sense Inputs (Supervised door sense inputs)
Reader Present inputs (Reader connected/disconnected)
Request to Exit inputs (Supervised Egress Inputs)
Relay contacts for door control outputs (Form C dry contacts rated for 2.0 Amps @
12/24VDC continuous power)
Door shunt/Local Alarm/Outputs (Open Collector output rated for +12 VDC @ 100mA)
9.4.1 Power Supply
The 8-reader Expansion Module requires +5VDC for all logic. Relays, output drivers, etc. require
a +12VDC supply. The +5VDC and +12VDC is provided to the module via the 50-pin expansion
cable, which connects plug P1 of the 8-door cluster PCB (P/N 03-10102-201E) to plug J1 of the
IQ-400 board, (P/N 03-10111-201). The Variable Ambient Test will be for Indoor, 0 to 49 Degrees
C, and 85% Relative Humidity @ 30 Degrees C.
9.4.2 Door Sense LEDs
8 LEDs located at D17, D18, D19, D20, D21, D22, D23, and D24 indicate the status of the Door
circuits. Resistors must be installed at the door contacts, the switches in place, door closed
(normal state), and the lines calibrated, in order for the supervised inputs to function. See Section
2.2.5.1.2 [Proper Point by Point Calibration] of the LiNC-NET Administrator Guide (P/N: 3810055-001) for calibration procedure.
LED Status Chart:
•
•
•
•
•
•
•
•
Sense Input #25 LED is D17
Sense Input #27 LED is D18
Sense Input #29 LED is D19
Sense Input #31 LED is D20
Sense Input #33 LED is D21
Sense Input #35 LED is D22
Sense Input #37 LED is D23
Sense Input #39 LED is D24
OFF
ON
Blinks once every 2 seconds
Blinks 1 time/second
Blinks 4 times/second
IQ-400 Installation Manual
Circuit is in normal/secure state
Circuit is in an alarm condition state
Fault condition. Open circuit state
Fault condition. Short circuit state
Circuit is NOT calibrated and NOT in a
functional state
Page 82 of 100
33-10057-001-A
9.5 IQ-1200 Features (IQ-400 plus 8-Reader Expansion Module)
2 Auxiliary (Powered) Outputs (cc# 89, 90)
12 Reader Ports:
(Wiegand electrical interface for PCSC and OEM card readers) (readers a-l)
12 Form C Door Strike Outputs (2.0 amps @ 12/24 VDC continuous power)
12 Door Left Open Outputs (or 12 External Shunt Options)
12 Supervised Door Senses (17, 19, 21, 23, 25, 27, 29, 31, 33, 35, 37, 39)
5 Supervised User-Defined (Auxiliary) Sense Inputs (S14, S120, S121, S122, S123)
12 Supervised Request to Exit Inputs (16, 18, 20, 22, 24, 26, 28, 30, 32, 34, 36, 38)
Battery Backed Clock Calendar
Flash RAM 128K standard (up to 256K)
Battery-Backed RAM 256K standard (up to 512K)
LEDs for:
Power, alarm, on-line diagnostics Reader Data [Error code, door status]
Unsupervised Tamper detect (S13)
9.5.1 System Capacities
Cardholder Capacity:
Time Periods:
Holiday Time Periods:
Holiday List:
History Transactions:
Enclosure Dimensions:
Weight:
Power:
Draw:
Temperature:
Communications:
8,000 (20,000 w/ Memory Expansion)
32
32
366 Days (Leap Year)
4,000 regardless of memory size
18”H x 11.5”W x 6”D
(45.7cm x 29.2cm x 15.2cm)
38 lbs. (17.3kg)
12VDC
3 amp @ 12VDC
32°F to 115°F (0°C to 46°C)
RS485 standard
RS232 standard
External MODEM or (optional On-Board Modem)
Ethernet optional
9.5.2 Spare Parts- 8-Reader Expansion Board (P/N: 03-10102-201F)
Part Number
Description
Designation
83-02082
83-02086
79-03022
83-2007
5-pin Plug Connector
9-pin Plug Connector
DPST Relay
Jump Connector
P2, P4, P6, P8, P10, P12, P14, P16
P3, P5, P7, P9, P11, P13, P15, P17
K1- K8
W1-W15
IQ-400 Installation Manual
Page 83 of 100
33-10057-001-A
9.6 OUT PCB Features (P/N: 03-10032-201F)
16 Form C Relay Dry Contact Outputs (2.0 amps @ 12/24 VDC continuous power)
16 Unsupervised Sense Inputs (Alarm points 56-71)
LEDs for:
status, +5Vdc, +12VDC, watchdog timer (wdt)
9.6.1 System Capacities
Enclosure Dimensions:
Weight:
Temperature:
Communications:
18”H x 11.5”W x 6”D
(45.7cm x 29.2cm x 15.2cm)
38 lbs. (17.3kg)
32°F to 115°F (0°C to 46°C)
50-pin Ribbon Cable
9.6.2 Electrical Ratings
Draw:
Relay Contacts
500 mA @ 12 VDC
2A @ 24 VDC
9.6.3 Spare Parts- OUT PCB
Part Number
83-02083
83-02084
79-03022
83-2007
Description
2-pin Plug Connector
4-pin Plug Connector
DPST Relay
Jump Connector
IQ-400 Installation Manual
Designation
P13 (Pins 5-6)
P1- P12 (two connectors per plug), P13 (Pins 1-4)
K1- K16
P14
Page 84 of 100
33-10057-001-A
9.7 ALM PCB Features (P/N:P 03-10032-301)
16 Unsupervised Sense Inputs (Alarm points 56-71)
9.7.1 System Capacities
Enclosure Dimensions:
Weight:
Temperature:
Communications:
18”H x 11.5”W x 6”D
(45.7cm x 29.2cm x 15.2cm)
38 lbs. (17.3kg)
32°F to 115°F (0°C to 46°C)
50-pin Ribbon Cable
9.7.2 Electrical Ratings
Draw:
Relay Contacts
100mA @ 12 VDC
2 A @ 24 VDC
9.7.3 Spare Parts- ALM PCB (P/N: 03-10032-301)
Part Number
Description
Designation
83-02083
83-02084
83-2007
2-pin Plug Connector
4-pin Plug Connector
Jump Connector
P13 (Pins 5-6)
P1- P4 (two connectors per plug), P13 (Pins 1-4)
P14
IQ-400 Installation Manual
Page 85 of 100
33-10057-001-A
9.8 Cable Requirements and Maximum Lengths
9.8.1 CommunicationType of
Technology
IQ-400
Type of 22awg
Stranded Wire
2-pair, twisted, w/
overall shield
Maximum Distance
Type of
Technology
Models Type of 22awg
Stranded Wire
Maximum Distance
ProTech
BR-350 2-pair, twisted, w/ 2000 ft.
overall shield
(667 m)
Max. Distance w/PIN Pad
(BP-250)
To the last IQ-400
(4,000 ft (1,219 m)
9.8.2 Readers
4-wire PCSC-
5-wire Wiegand-
Max. Distance w/PIN Pad
(BP-250)
2000 ft.
(667 m)
Type of
Technology
Models
Type of 22awg
Stranded Wire
Maximum Distance
Max. Distance w/PIN Pad
(Bp-270)
ProTech
BR-370
3-pair, twisted, w/
overall shield
500 ft.
(192 m)
500 ft.
(192 m)
Proximity
All models 3-pair, twisted, w/
overall shield
500 ft.
(192 m)
500 ft.
(192 m)
Biometric
All models 3-pair, twisted, w/
overall shield
500 ft.
(192 m)
500 ft
(192 m)
Bar Code
All models 3-pair, twisted, w/
overall shield
500 ft.
(192 m)
500 ft
(192 m)
Vehicle ID
VR-670
500 ft.
(192 m)
500 ft
(192 m)
3-pair, twisted, w/
overall shield
2-pair twisted and shielded cable recommended brands are:
Belden 8728 Olympic 3030 Alpha 2404 or 2212
3-pair twisted and shielded cable recommended brands are:
Belden 8777 Alpha 6010C WPW D431
NOTE All data communications cables must reside in a separate electrical
conduit. Absolutely NO high voltage or AC power cables allowed within
data conduits.
IQ-400 Installation Manual
Page 86 of 100
33-10057-001-A
9.9 Tool Requirements
Cable Connection Tool
Inserting the cable to the AMP connectors from the
PCSC readers must be performed with either an AMP
Insertion Handle (P/N 88-08003) w/ an AMP Head (P/N
88-08005) or an AMP hand tool (P/N 88-08006) for MTA
connectors. Any other tool may cause improper
connection or damage to the system. On the IQ-400
circuit board, a standard screwdriver is required for
securing cabling connections.
Reader Locking Tool
As a security measure, some readers are equipped with
a security bolt. This bolt requires a special driver (P/N
88-08002) to secure each reader and PIN pad.
9.10 Controller Specifications
Microprocessor
The IQ-400 Controller is based on a 80C188EB
microprocessor, operating at 16 MHz. The 80C188EB is
a 16-bit processor (internal operation) with an eight-bit
data bus. A 20-bit address bus provides a 1M Byte
addressing range. Other features include three internal
16-bit timers, interrupt controller (8529 equivalent),
multiple programmable chip select decoders with
programmable wait states, and two serial communication
channels.
LEDs and Dipswitches
30 discrete LEDs are provided which the microprocessor
software can individually control. Eight general-purpose
switches are provided for use by the microprocessor
software, and are utilized for mode control, configuration
setting, ID selection, etc. In addition, a Power ON LED
and four “Reader Active” LEDs are provided.
Two Seven-Segment LED Display
Error codes are displayed in Hexadecimal format. Refer
to the error code section for listing of codes and their
meanings.
Real Time Clock
A real time clock (DS1302) with battery backup is
provided for time of day information.
IQ-400 Installation Manual
Page 87 of 100
33-10057-001-A
Serial Communication
Two serial communication ports are provided by the
IQ-400 controller.
•
RS-485: Four wire (twisted pair) interface which is
optically isolated from the controller.
-Provision for installing a termination resistor is
provided.
•
RS-232: At P7 (RS232 DB9 – Real Time Printer
Port). At P2 (RS232 Direct Connect) – standard
RS232 interface. Jumper W6 adds/removes an
onboard 120Ω End-of-Line Termination Resistor.
Power Supply
The IQ-400 controller requires +5VDC for all logic.
Relays, output drivers, etc. require a +12VDC supply. An
on-board dc-dc converter accepts an external voltage
source of 10-26VDC, and converts this unregulated
source to the required +5VDC. For an input voltage
range of 10-15 volts, the “+12VDC” converts this voltage
source to the required +12VDC. For more information,
please refer to the ESD power supply installation
manual.
Battery Back-up Requirements
A 7 AH battery is recommended as a back-up to the
power supply, because it is the largest battery that will fit
in the enclosure. The battery should be connected to the
power supply charger in accordance with the
manufacturer’s instructions. Refer to ESD SPS-3.6M2E,
or SPS-6.5M4 Power Supply installation instructions for
determining battery backup size.
Factory Settings
At the factory the IQ-400 is set as IQ-400 #1,
communications as direct connect (RS232/RS485) @
9600 baud, with 120 Ohm resistor termination disabled
(W6 jumper set at 1-2).
IQ-400 Installation Manual
Page 88 of 100
33-10057-001-A
9.11 Four-Reader Expansion Board- Active LEDs (P/N: 03-10102-301E)
4 LEDs located at D61, D62, D67, D68 indicate the status of the Reader circuits. When the LED
blinks momentarily after a card swipe, the system is processing the card data. The LED is
normally off.
Reader LED Status:
•
•
•
•
Reader E LED is D61
Reader F LED is D62
Reader G LED is D67
Reader H LED is D68
9.11.1 Jumpers
Reader type is selected by the use of jumpers located in between the reader ports at W5 and
W11-W14. Refer to each diagram of reader-types on Section 5.0 [Reader Connections] for the
proper setting of these jumpers. Four other jumpers, located at W1, W2, W3, W6 and W15,
designate chip selection, and are set at the factory. They should not be changed unless directed
by technical support.
The setting of the four jumpers at W5 (4W or 5W) determines how the jumpers next to each
reader port is set. Also, when using a 5-wire, 12VDC reader, you can control the voltage at PIN 1,
by moving the leftmost jumpers at W5 in conjunction with the reader port jumper setting (see
Section 9.11.2 – next page).
IQ-400 Installation Manual
Page 89 of 100
33-10057-001-A
9.11.2 Four-Reader Expansion Board (P/N: 03-10102-301E) - Jumper Selections
There are five jumper units located on the 4-Reader Expansion PCB circuit board. The settings
are shown below.
•
•
•
•
•
W1 at Pins 2 and 3 = PCB addressed to 30h (LO Address)
W1 at Pins 1 and 2 = PCB addressed to 50h (HI Address – Default Settings)
W2 and W3 at pins 1 and 2 = A/D is max 158 type
W2 and W3 at pins 2 and 3 = A/D is max 7828 type
W4 NOT USED ON 4-READER EXPANSION PCB
•
W5 (for Readers e-h)
•
•
•
At pins 1 and 2, 4 and 5, 7 and 8, 10 and 11= Wiegand 5-Wire 5 volt card
readers
At pins 2 and 3, 4 and 5, 7 and 8, 10 and 11= Wiegand 5-Wire 12 volt card
readers
At pins 2 and 3, 5 and 6, 8 and 9, 11 and 12= PCSC 4-Wire 12 volt card
readers
W6 – Reader T/O
At pins 1 and 2 = 32 ms (PCSC Factory Set. Do not modify)
At pins 2 and 3 = 64 ms
W11-W14 Reader Data Format
At pins 1 and 2 = Wiegand 5-wire (Data 1’s and Data 0’s) format
At pins 2 and 3= PCSC 4-wire (proprietary) format
SW1 Switch Settings (to configure PCB for doors 5-8)
Switches 2 = OFF
Switches 1,3,4,6,7,8 = ON = 4 Reader PCB
Switch 5 = ON to enable Supervision Option of ALL Egress Sense Inputs
(#24, 26, 28, and 30).
Switch 5 = OFF to disable Supervision of ALL Egress Sense Sense Inputs
(#24, 26, 28, and 30).
NOTE
IQ-400 Installation Manual
Supervised Egress Option requires i4+07.010.02 series (or newer) IQ400 firmware.
Page 90 of 100
33-10057-001-A
9.12 Eight-Reader Expansion Board (P/N: 03-10102-201E) - Active LEDs
Eight LEDs located at D49, D50, D55, D56, D61, D62, D67, D68 indicate the status of the Reader
circuits. When the LED blinks momentarily after a card swipe, the system is processing the card
data. The LED is normally off.
Reader LED Status:
•
•
•
•
•
•
•
•
Reader E LED is D49
Reader F LED is D50
Reader G LED is D55
Reader H LED is D56
Reader I LED is D61
Reader J LED is D62
Reader K LED is D67
Reader L LED is D68
9.12.1 Jumpers
Reader type is selected by the use of jumpers located in between the reader ports at W4-W5 and
W7-W14. Refer to each diagram of reader-types in Section 5 [Reader Connections] for the proper
setting of these jumpers. Four other jumpers, located at W1, W2, W3, W6, and W15 designate
chip selection, and are set at the factory. They should not be changed unless directed by
technical support.
The setting of the jumpers at W4 and W5 (4W or 5W) determines how the jumpers next to each
reader port is set. Also, when using a 5-wire, 12VDC reader, you can control the voltage at PIN 1,
by moving the #3 jumpers at W4 and W5 in conjunction with the reader port jumper setting.
IQ-400 Installation Manual
Page 91 of 100
33-10057-001-A
9.12.2 Eight-Reader Expansion Board (P/N: 03-10102-201E) - Jumper Selections
There are five jumper units located on the 8-Reader expansion PCB circuit board. The settings
are shown below.
•
•
•
•
W1 at Pins 2 and 3 = PCB addressed to 30h (LO Address)
W1 at Pins 1 and 2 = PCB addressed to 50h (HI Address = Default Settings)
W2 and W3 at pins 1 and 2 = A/D is max 158 type
W2 and W3 at pins 2 and 3 = A/D is max 7828 type
•
•
•
•
•
•
•
•
•
•
•
W4 (for Readers e-h)
At pins 1 and 2, 4 and 5, 7 and 8, 10 and 11= Wiegand 5-Wire 5 volt card
readers
At pins 2 and 3, 4 and 5, 7 and 8, 10 and 11= Wiegand 5-Wire 12 volt card
readers
At pins 2 and 3, 5 and 6, 8 and 9, 11 and 12= PCSC 4-Wire 12 volt card
readers
W5 (for Readers i-l)
At pins 1 and 2, 4 and 5, 7 and 8, 10 and 11= Wiegand 5-Wire 5 volt card
readers
At pins 2 and 3, 4 and 5, 7 and 8, 11 and 12= Wiegand 5-Wire 12 volt card
readers
At pins 2 and 3, 5 and 6, 8 and 9, 11 and 12= PCSC 4-Wire 12 volt card
readers
W6 – Reader T/O
At pins 1 and 2 = 32 ms (PCSC Factory Set. Do not modify)
At pins 2 and 3 = 64 ms
W7-W14 Reader Data Format
At pins 1 and 2 = Wiegand 5-wire (Data 1’s and Data 0’s) format
At pins 2 and 3= PCSC 4-wire (proprietary) format
SW1 Switch Settings (to configure PCB for doors 5-12)
Switches 1, = OFF
Switches 2,3,4,5,6,7,8 = ON = 8 Reader PCB
Switch 5 = ON to enable Supervision Option of ALL Egress Sense Inputs
(#24, 26, 28, 30, 32, 34, 36 and 38).
Switch 5 = OFF to disable Supervision of ALL Egress Sense Sense Inputs
(#24, 26, 28, 30, 32, 34, 36 and 38).
NOTE
IQ-400 Installation Manual
Supervised Egress Option requires i4+07.010.02 series (or newer) IQ400 firmware.
Page 92 of 100
33-10057-001-A
10.0 Appendix B – Configuring the IQ LAN for Version 0130 and above
10.1 Configuring the IQ LAN for Version 0130 and above
The following Configuration Instructions are for updating the IQ LAN (PCSC Part #: 03-10108xxx) TCP/IP Configuration.
IMPORTANT
If a user is configuring the IQ LAN card for a panel addressed 112-200, the
software addressing of the panel must be configured BEFORE the IQ LAN
configuration. For more information on software addressing, see Section 7.3.2
[Software Addressing the IQ-400 Panel (Panels 112-200) Direct Connect].
10.1.1 Required Equipment:
1. PC or Notebook computer with a NIC
2. Web Browser (IE 5 or greater or Netscape 5 or greater.)
3. Ethernet Cross Over cable (example: Unicom E5DD-C414-WT-10TR) or attached to
a hub
4. IQ-400 – 03-10111-xxx
5. IQ LAN – 03-10108-xxx
10.1.2 Required Information:
1. LiNC-NET Host IP Address
2. IQ LAN IP Address – This is the unique IP Address for each IQ-400.
3. Panel Number – This is the IQ-400 panel number that the IQ LAN will be attached to.
The panel number in the IQ LAN and the IQ-400 PCB must match.
4. Any Gateway information.
10.1.3 Required firmware:
1. IQ-400 panel firmware: i4+07.010.02 or greater
2. IQ LAN version 0130 or greater
IQ-400 Installation Manual
Page 93 of 100
33-10057-001-A
10.2 Configuring your Host Computer
1. Change host IP to be 192.168.168.3 in your computer’s TCP/IP settings - This is the
default Host IP address that the IQ LAN uses for setup:
a. Right mouse click on “My Network Places”
b. Select: Properties
c. Right mouse click on “Local Area Connection”
d. Highlight Internet Protocol [TCP/IP] and Press the Properties button.
e. You will need to verify that you have “Use the following IP address” selected.
See screen below.
f.
g.
h.
i.
Enter 192.168.168.3 for the I.P. address
Enter 255.255.255.0 for the Subnet mask
Press the OK button
Reboot the host computer if necessary. Depending on you system you may
or may not have to do this.
IQ-400 Installation Manual
Page 94 of 100
33-10057-001-A
10.3 Configuring IQ LAN VIA the TCP/IP Configurator
Use a Web Browser to configure and view the IQ LAN Configuration Information (IE 5 or greater,
or Netscape 5 or greater). You will need to know the following information, IQ LAN IP address 192.168.168.32, Logon Name - admin, and Logon Password – PYMTF
The following steps are for connecting and changing the TCP/IP Configuration.
1. Connect your Cross Over cable from your host to the IQ LAN
Note:
Once you have powered up the IQ-400 and have successfully made a
connection to the Host, the IQ LAN R45 connectors Green LED will turn
ON. You will also see the Yellow LED strobe when it is trying to
communicate to the Host.
2. Open your Browser (e.g. Internet Explorer, Netscape, etc.)
3. Request the configuration form by entering the following in the “Address” field of the
Browser. http://192.168.168.32
4. An html form will appear (figure on next page).
IQ-400 Installation Manual
Page 95 of 100
33-10057-001-A
10.3.1 TCP/IP Configuration
5. Change the appropriate values.
a. Panel Number – This must match the IQ-400 panel number.
b. Host IP – This is the LiNC-NET Host IP
c.
Our IP (IQ LAN IP) - This is the IQ LAN address that LiNC-NET will use to
communicate to the IQ-400 panel.
6. Enter the Logon Name – admin
7. Enter Logon Password – PYMTF
8. Click on the Update button. The following screen(s) will appear depending on the
field you have changed.
IQ-400 Installation Manual
Page 96 of 100
33-10057-001-A
192.168.12.105
IQ-400 Installation Manual
Page 97 of 100
33-10057-001-A
9. Close the Browser. You will have to change your Host IP to match the Host IP
address just entered in the TIP/IP Configuration
10. Re-open the Browser. Call out the new IQ LAN address. You should now see all of
the updated information.
Note:
Once you have changed the Host IP in the IQ LAN, the host IP must match. If
they do not then you will not be able to view the TCP/IP configuration
information.
Update IQ panel firmware – Reference IQ-Series Downloader Installation Instructions Technical
Bulletin (P/N: 39-10050-001).
IQ-400 Installation Manual
Page 98 of 100
33-10057-001-A
10.4 Resetting the LAN (External Peripheral or Embedded) Ethernet Module
If the IQ LAN module is accidentally set to an incorrect (and/or unknown) IP address, it is possible
to reset the IQ LAN module to original default IP address.
1. Power off the IQ-400 board.
2. Reset SW1 DIPswitch to (11101110)
3. Power up the board. The IQ-400 board
LED Array will initially show 8.8., then
8.6., then 8.8. once again –board is now
reset. The board reset has created the
following default values:
a. Logon is “admin”
b. Password is “PYMTF”
c.
“Host IP” is reset to ‘0’
d. “Our IP” is reset to 192.168.168.32
4. Using your Internet browser, type in the IP address 192.168.168.32. The IQ LAN
module should be in default mode.
NOTE Your computer’s TCP/IP has to be set to the 192.168.168.xxx for proper
communication to the panel.
5. See page 104, steps 5 through 8, for proper resetting of the TCP/IP configuration for
the board.
NOTE When reset, the LAN module will default to Panel 1 and the default
address.
end/
IQ-400 Installation Manual
Page 99 of 100
33-10057-001-A
End of Manual
PCSC, Inc.
February 2004
IQ-400 Installation Manual
Page 100 of 100
33-10057-001-A