Peugeot 04

Add to my manuals
344 Pages

advertisement

Peugeot 04 | Manualzz
HANDBOOK
On-line handbook
You can find your handbook on the PEUGEOT website, under
"Personal space".
Referring to the handbook on-line also gives you access to the
latest information available, easily identified by the bookmark,
associated with this symbol:
Please note the following point:
The fitting of electrical equipment or accessories which are
not recommended by PEUGEOT may result in a failure of your
vehicle's electronic system. Please note this specific warning.
It is advisable to contact a PEUGEOT dealer to be shown the
recommended equipment and accessories.
If the "Personal space" function is not available on the PEUGEOT
public website for your country, you can find your handbook at the
following address:
http://public.servicebox.peugeot.com
Select:
The Vehicle documentation link in the home page (no registration is
needed),
the language,
the vehicle, its body style,
the print edition of your handbook appropriate for the date of registration
of your vehicle.
You have access to your handbook on line, together with the latest
information, identified by the symbol:
WELCOME
Thank you for choosing an RCZ, a symbol of confidence, passion and
inspiration.
This handbook has been designed to enable you to make the most of
your vehicle in all situations.
Therefore, on the first few pages, you will find a list of contents followed
by a quick reference guide intended to make it easier for you to become
familiar with your vehicle.
All of the details specific to your vehicle, comfort, safety, driving, are
then presented in this handbook, to increase your appreciation of the
vehicle and to help you make the most of it.
Your vehicle is fitted with only some of the equipment described in this
document, depending on its trim level, version and the specification for
the country in which it was sold.
KEY
WARNING:
this symbol marks warnings which it is essential to observe for
your own safety, for the safety of others or to avoid any risk of
damaging your vehicle.
INFORMATION:
this symbol draws your attention to additional information for
better use of your vehicle.
PROTECTION OF THE ENVIRONMENT:
this symbol accompanies advice relating to protection of the
environment.
PAGE REFERENCE:
this symbol invites you to refer to the pages which provide details
of the function.
CONTENTS
FAMILIARISATION
4-19
ECO-DRIVING
20-21
1/MONITORING
22-50
Instrument panels
Warning and indicator lamps
Indicators
2/ACCESS
2
3/EASE OF USE and COMFORT
4/VISIBILITY
Lighting controls
LED lamps
Automatic illumination of headlamps
5/SAFETY
Direction indicators
Hazard warning lamps
Emergency or assistance call
Horn
Instrument panel buttons
Clock
Trip computer
37
38
39
Monochrome screen C (PEUGEOT
PEUGEOT Connect Sound (RD5))
Retractable colour screen (PEUGEOT Connect Navigation (RT6))
Retractable colour screen (PEUGEOT Connect Media Navigation (NG4 3D))
51
55
Electric windows
Doors
58
60
Boot
64
68
69
72
73
Dual-zone digital air conditioning
Rear screen demist - defrost
Courtesy lamp
Interior mood lighting
75
77
78
79
Interior fittings
Front armrest
Boot fittings
89
92
93
Headlamp adjustment
Directional lighting
Wiper controls
95
96
97
Automatic rain sensitive wipers
42
46
48
51-63
Remote control key
Alarm
Front seats
Steering wheel adjustment
Mirrors
Rear seats
Ventilation
22
26
33
63
64-88
81
84
87
89-100
99
101-128
101
101
102
102
Braking assistance systems
Trajectory control systems
Active bonnet
Active spoiler
103
104
106
107
Front seat belts
Airbags
Child seats
Deactivating the passenger's front airbag
110
113
118
120
CONTENTS
6/DRIVING
Steering lock - Starting
Parking brake
Hill start assist
Manual gearbox
7/CHECKS
Fuel tank
Bonnet
Petrol engines
8/PRACTICAL INFORMATION
Temporary puncture repair kit
Changing a wheel
Snow chains
Changing a wiper blade
9/TECHNICAL DATA
Petrol engines
Weights (petrol)
129-148
129
130
131
132
Automatic gearbox
Gear shift indicator
Tyre under-inflation detection
Speed limiter
133
137
138
140
Cruise control
Parking sensors
150
152
153
Diesel engine
Running out of fuel (Diesel)
Checking levels
154
155
156
Checks
149-160
159
161-200
161
168
173
174
Energy economy mode
Battery
Changing a bulb
Changing a fuse
175
176
178
186
Towing a vehicle
Towing a trailer
Cleaning and maintenance
Accessories
201
202
Diesel engine
Weights (Diesel)
203
204
Dimensions
Identification markings
193
195
197
199
201-206
10/ AUDIO EQUIPMENT and TELEMATICS
Emergency or assistance
PEUGEOT Connect Media Navigation (NG4 3D)
143
146
207
211
PEUGEOT Connect Navigation (RT6)
PEUGEOT Connect Sound (RD5)
205
206
207-328
255
309
ALPHABETICAL INDEX
329-333
VISUAL SEARCH
334-340
EXTERIOR
1. Welcome lighting
This additional exterior and
interior lighting, controlled
remotely, makes your approach to
the vehicle easier when the light
is poor.
79
4
2. Directional lighting
This lighting automatically
provides additional visibility when
cornering.
96
Aluminium arches
For maintenance of these
arches, do not use a dry
cloth with an abrasive
product. Use a sponge and
soapy water.
3. Spoiler
This system improves the
aerodynamics of the vehicle.
107
4. Front and rear parking
sensors
This system warns you of any
obstacles detected in front of or
behind the vehicle when parking.
146
5. Temporary tyre repair kit
This kit is a complete system,
consisting of a compressor
and a sealant cartridge, for the
temporary repair of a tyre.
161
ACCESS
Normal locking
(press once; fixed lighting of the
direction indicators).
or
Deadlocking the vehicle
(press twice in succession; fixed
lighting of the direction indicators).
Unlocking and partial opening of
the boot lid
(press for more than two seconds).
Unfolding / Folding the key
(press first before unfolding or folding the key).
Complete or selective unlocking of
the vehicle
(rapid flashing of the direction
indicators).
51
WELCOME LIGHTING
When poor light is detected by a sensor,
the remote switching on of the dipped beam
headlamps and sidelamps makes your
approach to the vehicle easier.
80
In the same way, the passenger compartment
lighting, such as the courtesy lamps, the door
sill lamps and the footwell lamps, comes on.
79
FAMILIARISATION
REMOTE CONTROL KEY
BOOT
FUEL TANK
Vehicle locked
1.
2.
Unlocking and partial opening of the boot lid.
Open the boot lid.
6
Vehicle unlocked
For access to the fuel filler cap, the vehicle must be unlocked.
1. Open the fuel filler flap by pressing at its rear edge.
2. Remove the fuel filler cap by unscrewing it and hook it on to the
back of the filler flap.
Capacity of the tank: approximately 55 litres.
150
1.
2.
Partial opening of the boot lid.
Open the boot lid.
63
INTERIOR
1. Interior mood lighting
This dimmed lighting of the passenger
compartment facilitates visibility inside the
vehicle when the light is poor.
79
2. Audio and telematic systems
This equipment benefits from the latest technology:
MP3 compatible PEUGEOT Connect Sound (RD5),
PEUGEOT Connect Navigation (RT6) or PEUGEOT
Connect Media Navigation (NG4 3D) with 16/9 retractable
colour screen, JBL audio system, auxiliary sockets.
PEUGEOT Connect Media Navigation (NG4 3D)
PEUGEOT Connect Navigation (RT6)
255
PEUGEOT Connect Sound (RD5)
309
PEUGEOT Techno PVC
For maintenance of this trim, do not use
solvent or detergent with a dry cloth.
Remove dust first, then use a soft cloth
and soapy water. Dry using another soft
cloth.
3. Dual-zone digital air conditioning
This systems allows different levels of comfort
to be set for the driver and front passenger.
It then controls these levels automatically
according to the ambient conditions.
75
4. Active spoiler control
(except 1.6 litre THP 270 hp version)
This automatic system can be controlled
manually by means of this control on the
centre console.
107
FAMILIARISATION
211
INSTRUMENTS AND CONTROLS
8
1.
2.
3.
Cruise control / speed limiter switches.
Steering wheel adjustment control.
Lighting and direction indicator control
stalk.
4. Instrument panel.
5. Driver's airbag.
Horn.
6. Gear lever.
7. Parking brake.
8. Bonnet release.
9. Fusebox.
10. Manual headlamp height adjustment.
11. Side adjustable air vent.
12. Speaker (tweeter).
INSTRUMENTS AND CONTROLS
1.
FAMILIARISATION
Wipers / screenwash / trip computer
control stalk.
2. Steering lock and ignition.
3. Audio and telematics system steering
wheel control stalk.
4. Door mirror controls.
Electric window controls.
5. Central adjustable air vents.
6. Windscreen demisting vent.
7. Sunshine sensor.
8. Front side window demisting vent.
9. Passenger's airbag deactivation switch.
10. Glove box / Audio/video sockets.
11. Passenger's airbag.
CENTRE CONSOLES
1.
2.
3.
10
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Audio and telematic system microphone.
Courtesy lamp / Map reading lamps /
Interior mood lighting.
Seat belt and front passenger's airbag
warning lamps display.
Interior volumetric sensors (alarm).
Multifunction screen.
Clock.
Emergency call button.
Alarm button.
Central locking button.
Hazard warning lamps button.
Dynamic stability control (ESC/ASR/EBA)
button.
Parking sensors button.
PEUGEOT services button.
PEUGEOT Connect Sound (RD5)
and storage compartment, PEUGEOT
Connect Navigation (RT6) or PEUGEOT
Connect Media Navigation (NG4 3D).
Heating / air conditioning controls.
Front ashtray.
12 V accessories socket.
Active spoiler control.
Storage compartment or instrument panel
navigator associated with the PEUGEOT
Connect Media Navigation (NG4 3D).
Cup holder.
Front armrest / USB / auxiliary socket.
SITTING COMFORTABLY
Forwards-backwards
Height
Seat back angle
MANUAL ADJUSTMENTS
64
ELECTRIC ADJUSTMENTS
65
FAMILIARISATION
FRONT SEATS
12
SITTING COMFORTABLY
FRONT SEATS
STEERING WHEEL ADJUSTMENT
Other functions available...
1.
2.
3.
Lumbar adjustment.
FRONT ARMREST
Release the adjustment mechanism.
Adjust for height and reach.
Lock the adjustment mechanism.
66
Heated seats.
66
Storing of driving positions (driver's electric
seat).
67
As a safety precaution, these
operations must only be carried out
when stationary.
68
For your comfort, the height and the
longitudinal position of the front armrest can
be adjusted.
It also offers a storage compartment.
84
SITTING COMFORTABLY
DOOR MIRRORS
REAR VIEW MIRROR
FRONT SEAT BELTS
Automatic day/night model
A. Selection of the mirror to be adjusted.
B. Adjustment of the position of the mirror in
the four directions.
C. De-selection of the mirror.
71
1.
2.
3.
69
Other functions available...
Folding / Unfolding.
Automatic tilting of the mirror in reverse
gear for parking.
70
Fitting the belt.
Fastening the buckle.
Checking the fastening by pulling the
strap.
110
FAMILIARISATION
Adjustment
A. Automatic "day/night" mode light detector.
B. Adjustment of the mirror.
SEEING CLEARLY
LIGHTING
DIRECTION INDICATORS
WINDSCREEN WIPERS
2.
Fast wipe.
1.
Normal wipe.
I.
Intermittent wipe.
0.
Park.
AUTO  Automatic wipe or single wipe.
Wash-wipe: pull the stalk towards you.
14
97
Ring A
Lighting off.
Automatic illumination of headlamps.
Sidelamps.
Dipped / main beam headlamps.
Ring B
Rear foglamp.
90, 91
Raise or lower the lighting stalk passing
the point of resistance; the corresponding
direction indicators will flash until the stalk is
moved from this position.
101
Three flashes
Press the lighting stalk up or down once,
without passing the point of resistance; the
corresponding direction indicators will flash
three times.
The use of this function is available regardless
of the speed, but you will find it particularly
useful when changing lane on fast roads.
Switching on "AUTO"
 Press the stalk down and release it.
Switching off "AUTO"
 Push the stalk up and return it to
position "0".
99
MONITORING
INSTRUMENT PANEL
WARNING LAMPS
SWITCH PANEL
Illumination of the indicator lamp indicates the
status of the corresponding function.
A. Emergency call.
22
-
With the ignition on, the orange and red
warning lamps come on.
With the engine running, these warning
lamps should go off.
If warning lamps remain on, refer to the page
concerned.
26
208, 209
B. Deactivation of the interior volumetric and
anti-tilt sensors (alarm).
56
C. Central locking.
61
D. Deactivation of the DSC/ASR system.
105
E. Deactivation of the front and rear parking
sensors.
147
F.
Access to PEUGEOT services.
208, 209
FAMILIARISATION
The instrument panel has permanent backlighting for improved visibility in all situations,
both day and night.
With the ignition on, the fuel gauge needle
should indicate the level of fuel remaining.
With the engine running, its associated
low level warning lamp should go off.
With the ignition on, the oil level indicator
should display "OK" or "correct",
depending on version, for a few seconds.
If the levels are not correct, top up the levels
which are low.
STARTING
16
PASSENGER SAFETY
PASSENGER'S FRONT AIRBAG
SEAT BELTS AND
PASSENGER'S FRONT AIRBAG
IGNITION SWITCH
 Selection of the position:
"OFF" (deactivated), with "rearward
facing" child seat,
"ON" (activated), with front passenger or
"forward facing" child seat.
A. Front and/or rear seat belts not fastened /
unfastened warning lamp.
B. Front left seat belt warning lamp.
C. Front right seat belt warning lamp.
D. Rear right seat belt warning lamp.
E. Rear left seat belt warning lamp.
F. Passenger's front airbag deactivated
warning lamp.
G. Passenger's front airbag activated
warning lamp.
1.
2.
3.
114, 119
110, 114, 119
Stop position.
Running position.
Starting position.
Avoid attaching any heavy objects to the
key which would weigh down on its shaft
in the ignition switch; this could cause a
malfunction.
129
AT THE REAR
1.
2.
REAR SEAT BELTS
FOLDING DOWN THE REAR
BACKREST
1.
Release the backrest by pulling the
handle from the boot.
2.
Fold the backrest onto the seat cushion
from the passenger compartment.
Releasing the backrest.
Tilting the backrest.
The control giving access to the rear
seats does not release the seat.
72
-
Insert the tongue A in the buckle A in the
middle of the rear seat.
Insert the tongue B in the outer buckle B.
Press the red button B then the black button A
to remove the seat belt.
111
72
FAMILIARISATION
ACCESS TO THE REAR SEATS
18
DRIVING SAFELY
SPEED LIMITER "LIMIT"
CRUISE CONTROL "CRUISE"
1. Limiter mode Selection / Off.
2. Decrease the programmed value.
3. Increase the programmed value.
4. Speed limiter On / Off.
The values must be set with the engine running.
1.
2.
140
3.
4.
Cruise control mode Selection / Off.
Programme a speed / Decrease the
programmed value.
Programme a speed / Increase the
programmed value.
Cruise control Off / Resume.
In order to be programmed or activated, the
vehicle speed must be higher than 25 mph
(40 km/h), with at least fourth gear engaged
on the manual gearbox (second gear for the
automatic gearbox).
143
DISPLAY IN THE INSTRUMENT
PANEL
The cruise control or speed limiter mode
appears in the instrument panel when it is
selected.
Cruise control
Speed limiter
FAMILIARISATION
ECO-DRIVING
Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO2 emissions.
OPTIMISE THE USE OF YOUR GEARBOX
CONTROL THE USE OF YOUR ELECTRICAL
EQUIPMENT
With a manual gearbox, move off gently and change up without
waiting. During acceleration change up early.
Before moving off, if the passenger compartment is too warm, ventilate it
by opening the windows and air vents before using the air conditioning.
Above 30 mph (50 km/h), close the windows and leave the air vents
open.
Remember to make use of equipment that can help keep the temperature
in the passenger compartment down (sunroof and window blinds...).
Switch off the air conditioning, unless it has automatic regulation, as soon
as the desired temperature is attained.
Switch off the demisting and defrosting controls, if not automatic.
Switch off the heated seat as soon as possible.
20
With an automatic or electronic gearbox, give preference to automatic
mode and avoid pressing the accelerator pedal heavily or suddenly.
The gear shift indicator invites you engage the most suitable gear: as
soon as the indication is displayed in the instrument panel, follow it
straight away.
For vehicles fitted with an electronic or automatic gearbox, this
indicator appears only in manual mode.
DRIVE SMOOTHLY
Maintain a safe distance between vehicles, use engine braking rather
than the brake pedal, and press the accelerator progressively. These
practices contribute towards a reduction in fuel consumption and CO2
emissions and also helps reduce the background traffic noise.
If your vehicle has cruise control, make use of the system at speeds
above 25 mph (40 km/h) when the traffic is flowing well.
Switch off the headlamps and front foglamps when the level of light
does not require their use.
Avoid running the engine before moving off, particularly in winter; your
vehicle will warm up much faster while driving.
As a passenger, if you avoid connecting your multimedia devices
(film, music, video game...), you will contribute towards limiting the
consumption of electrical energy, and so of fuel.
Disconnect your portable devices before leaving the vehicle.
LIMIT THE CAUSES OF EXCESS
CONSUMPTION
OBSERVE THE RECOMMENDATIONS ON
MAINTENANCE
Spread loads throughout the vehicle; place the heaviest items in the
bottom of the boot, as close as possible to the rear seats.
Limit the loads carried in the vehicle and reduce wind resistance (roof
bars, roof rack, bicycle carrier, trailer...). Use a roof box in preference.
Remove roof bars and roof racks after use.
Check the tyre pressures regularly, when cold, referring to the label in
the door aperture, driver's side.
Carry out this check in particular:
before a long journey,
at each change of season,
after a long period out of use.
Don't forget the spare wheel and the tyres on any trailer or caravan.
At the end of winter, remove snow tyres and refit your summer tyres.
Have your vehicle serviced regularly (engine oil, oil filter, air filter,
passenger compartment filter...) and observe the schedule of
operations recommended in the warranty and maintenance record.
When refuelling, do not continue after the third cut-off of the nozzle to
avoid any overflow.
At the wheel of your new vehicle, it is only after the first 1 800 miles
(3 000 kilometres) that you will see the fuel consumption settle down
to a consistent average.
PETROL - DIESEL MANUAL
OR AUTOMATIC GEARBOX
INSTRUMENT PANELS
With small central display screen
Panel grouping together the vehicle operation indication dials and
warning lamps, with permanent back-lighting.
DIALS
1.
2.
3.
4.
22
5.
6.
7.
With large central display screen
8.
Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).
Coolant temperature.
Indicates the temperature of the engine coolant (°Celsius).
Fuel level.
Indicates the quantity of fuel remaining in the tank.
Vehicle speed.
Indicates the current speed of the moving vehicle (mph or km/h).
Small display screen.
Central display screen.
Display management button.
Starts a manual CHECK.
Recalls the service information.
Resets the selected function to zero (trip distance recorder or
service indicator).
Lighting dimmer button.
Adjusts the brightness of the lighting of the instruments and
controls.
For more information, refer to the paragraph relating to the button
or function and its associated display.
DISPLAYS
Small display screen
A. Trip distance recorder.
(miles or km)
B. Distance recorder.
(miles or km)
C. Service spanner, if a service is due shortly or is overdue.
D. Speed limiter
(mph or km/h) or
Cruise control.
E. Indication of:
- a gear change*,
or
- the programme or gear (automatic gearbox).
F. Engine oil level indicator,
service indicator.
(miles or km)
These two functions are displayed when the ignition is switched on,
then disappear after a few seconds.
Warning and status indicator lamps / CHECK.
Trip computer.
Vehicle speed repeat**.
Alert messages***.
Vehicle parameters***.
Navigation - Guidance***.
These functions are displayed according to the selection.
* According to engine.
** Only on the large central display screen.
*** Only on the large central display screen with PEUGEOT Connect Media (NG4 3D).
1/ MONITORING
Central display screen
24
INSTRUMENT PANEL NAVIGATOR WITH THE LARGE CENTRAL DISPLAY
SCREEN AND PEUGEOT CONNECT MEDIA NAVIGATION (NG4 3D)
This group of buttons permits:
when stationary, configuration of the vehicle's equipment and of
the parameters of the central display (languages, units...),
while driving, scrolling of the active functions (trip computer,
navigation...).
The main menu and its associated functions can only be
accessed when stationary, via buttons 1 to 4.
A message appears on the central screen, above a certain speed
threshold, indicating that the main menu cannot be displayed.
The trip computer displays can only be accessed while driving, via
buttons 2 and 3 (refer to the "Trip computer" section).
Controls
There are four buttons to control the instrument panel large central
display screen:
1. access the main menu, confirm the selection,
2. move up through the menu,
3. move down through the menu,
4. return to the previous screen, exit from the menu.
Main menu
 Press button 1 for access to the main menu and select one of the
following functions:
- "Vehicle parameters",
- "Choice of language",
- "Choice of units".
 Press button 2 or 3 to move on the screen.
 Press button 1 again to confirm the selection.
This menu allows you to activate or deactivate certain driving and
comfort equipment:
vehicle speed repeat,
selective unlocking (refer to the "Access" section),
guide-me-home lighting (refer to the "Visibility" section),
interior mood lighting (refer to the "Ease of use and comfort"
section),
daytime running lamps** (refer to the "Visibility" section),
directional headlamps (refer to the "Visibility" section),
rear parking sensors (refer to the "Driving" section).
Choice of language
This menu allows you to select the language used by the display:
Deutsch, English, Espanol, Français, Italiano, Nederlands, Portugues,
Pусский, Portugues-Brasil, Türkçe**.
Choice of units
This menu allows you to select the units: temperature (°Celsius or
°Fahrenheit) and fuel consumption (l/100 km, mpg or km/l).
* Depending on version.
** Depending on country of sale.
1/ MONITORING
Vehicle parameters*
WARNING AND INDICATOR LAMPS
Visual indicators which inform the driver of the occurrence of a
fault (warning lamp) or of the operation of a system (operation or
deactivation indicator lamp).
When the ignition is switched on
Warning lamps
Certain warning lamps come on for a few seconds when the ignition is
switched on.
When the engine is started, these warning lamps should go off.
If they remain on, before moving off, refer to the information for the
warning lamp concerned.
When the engine is running or the vehicle is being driven, the
illumination of one of the following warning lamps indicates a fault which
requires action on the part of the driver.
26
Associated warnings
The illumination, fixed or flashing, of certain warning lamps may be
accompanied by an audible signal and a message in the screen.
Depending on your version of instrument panel, illumination of the
warning lamp is also accompanied by:
a symbol in the central instrument panel screen and a message in
the multi-function screen,
or
a symbol and a message in the central instrument panel screen.
The illumination of a warning lamp is always accompanied by the
display of an additional message, to assist you in identifying the
fault.
If you encounter any problems, contact a PEUGEOT dealer or a
qualified workshop.
is on
Cause
STOP
fixed, alone
or associated
with another
warning lamp,
accompanied by
an audible signal
and a message
in the screen.
Illumination of this warning lamp
is associated with a serious fault
with the braking system, power
steering, engine lubrication
system or cooling system.
Stop as soon as it is safe to do so as there is a risk that the
engine will cut out while driving.
Park, switch off the ignition and contact a PEUGEOT
dealer or a qualified workshop.
fixed, associated
with the STOP
warning lamp.
The braking system fluid level is
too low.
You must stop as soon as it is safe to do so.
Top up with brake fluid recommended by PEUGEOT.
If the problem persists, have the system checked by a
PEUGEOT dealer or a qualified workshop.
fixed, associated
with the STOP
and ABS warning
lamp.
The electronic brake force
distribution (EBFD) system has
a fault.
You must stop as soon as it is safe to do so.
Have it checked by a PEUGEOT dealer or a qualified
workshop.
The temperature of the cooling
system is too high.
Stop as soon as it is safe to do so.
Wait until the engine has cooled down before topping up
the level, if necessary.
If the problem persists, contact a PEUGEOT dealer or a
qualified workshop.
Braking
+
Maximum
coolant
temperature
fixed with the
needle in the red
zone.
Action / Observations
1/ MONITORING
Warning lamp
Warning lamp
is on
Cause
Action / Observations
on temporarily.
A minor fault has occurred for
which there is no specific warning
lamp.
Identify the fault by reading the message shown in the
screen, such as, for example:
opening of the doors, boot or bonnet,
low engine oil level,
low screenwash level,
flat remote control battery,
saturation of the particle emission filter (Diesel)
As soon as traffic conditions permit, regenerate the
filter by driving at a speed of at least 36 mph (60 km/h)
until the service warning lamp goes off.
a fault with the tyre under-inflation detection system,
...
For any other faults, contact a PEUGEOT dealer or a
qualified workshop.
fixed.
A major fault has occurred for
which there is no specific warning
lamp.
Identify the fault by reading the message shown on the
screen and contact a PEUGEOT dealer or a qualified
workshop.
flashing.
The engine management system
has a fault.
Risk of destruction of the catalytic converter.
Have it checked by a PEUGEOT dealer or a qualified
workshop.
fixed.
The emission control system has
a fault.
The warning lamp should go off when the engine is started.
If it does not go off, contact a PEUGEOT dealer or qualified
workshop without delay.
When it first comes on there
remains approximately 5 litres of
fuel in the tank.
At this point, you begin to use the
fuel reserve.
Refuel as soon as possible to avoid running out of fuel.
Until sufficient fuel has been added, this warning lamp
will come on every time the ignition is switched on,
accompanied by an audible signal and a message.
The audible signal and message are repeated with
increasing frequency as the fuel level drops towards "0".
Fuel tank capacity: approximately 55 litres.
Never continue to drive until you run out of fuel, as this
could damage the emission control and injection systems.
28
Service
Engine
autodiagnosis
system
Low fuel level
fixed with the
needle in the
red zone,
accompanied by
an audible signal
and a message.
Cause
Action / Observations
fixed.
The anti-lock braking system has
a fault.
The vehicle retains conventional braking.
Drive carefully at reduced speed and contact a PEUGEOT
dealer or a qualified workshop without delay.
flashing.
The DSC/ASR regulation is
operating.
The system optimises traction and improves the directional
stability of the vehicle in the event of loss of grip or
trajectory.
fixed.
The DSC/ASR system has a
fault.
Have it checked by a PEUGEOT or a qualified workshop.
Directional
headlamps
flashing.
The directional headlamps
system has a fault.
Have it checked by a PEUGEOT dealer or a qualified
workshop.
Seat belt not
fastened /
unfastened
fixed, then
flashing in the
passenger's seat
belt and front
airbag warning
lamp display.
Anti-lock
Braking
System (ABS)
Dynamic
stability control
(DSC/ASR)
+
Under-inflation
is on
The driver or front passenger has
not buckled or has unbuckled
their seat belt.
At least one rear passenger has
unbuckled their seat belt.
Pull on the belt in question and insert the tongue in the
buckle.
fixed.
The pressure in one or more
wheels is too low.
Check the pressure of the tyres as soon as possible.
This check should preferably be carried out when the tyres
are cold.
flashing then fixed,
accompanied
by the Service
warning lamp.
The tyre pressure monitoring
system has a fault or no sensor is
detected on one of the wheels.
Under-inflation detection is not assured.
Have the system checked by a PEUGEOT dealer or a
qualified workshop.
1/ MONITORING
Warning lamp
Operation indicator lamps
If one of the following indicator lamps comes on, this confirms that the
corresponding system has come into operation.
It may be accompanied by an audible signal.
Depending on your version of instrument panel, illumination of the
indicator lamp may also be accompanied by:
a symbol in the central instrument panel screen and a message in
the multifunction screen,
or
a symbol and a message in the central instrument panel screen.
30
Warning lamp
is on
Cause
Left-hand
direction
indicator
flashing with
buzzer.
The lighting stalk is pushed
down.
Right-hand direction
indicator
flashing with
buzzer.
The lighting stalk is pushed up.
Hazard warning
lamps
flashing with
audible signal.
The hazard warning lamps
switch, located on the dashboard,
has been operated.
Sidelamps
fixed.
The lighting stalk is in the
"Sidelamps" position or the
"AUTO" position with low light.
Dipped beam
headlamps
fixed.
The lighting stalk is in the
"Dipped beam headlamps"
position or in the "AUTO" position
in conditions of low light.
Main beam
headlamps
fixed.
The lighting stalk is pulled
towards you.
Action / Observations
The left-hand and right-hand direction indicators and their
associated indicator lamps flash simultaneously.
Pull the stalk again to return to dipped beam
headlamps.
is on
Cause
Action / Observations
Rear foglamp
fixed.
The rear foglamp is switched on.
Turn the ring on the stalk rearwards to switch off the rear
foglamp.
Diesel engine
pre-heating
fixed.
The ignition switch is at the
2nd position (ignition on).
Wait until the warning lamp has switched off before starting.
The duration for which the warning lamp is on is
determined by the climatic conditions.
fixed.
The parking brake is applied or
not properly released.
Release the parking brake to switch off the warning lamp,
keeping your foot on the brake pedal.
Observe the safety recommendations.
For further information on the parking brake, refer to the
"Parking brake" section.
fixed on the
seat belt and
passenger's front
airbag warning
lamps display.
The control switch, located on
the passenger's side of the
dashboard, has been placed in
the "ON" position.
The passenger's front airbag is
activated.
In this case, do not install a
"rearward facing" child seat.
While you do not have a rearward facing child seat fitted
to the front passenger seat, it is recommended that the
passenger's front airbag be activated.
On the other hand, before fitting a rearward facing child
seat, you must turn the control switch to the "OFF"
position.
Parking
brake
Passenger's
front airbag
1/ MONITORING
Warning lamp
Deactivation warning lamps
If one of the following warning lamps comes on, this confirms that the
corresponding system has been switched off intentionally.
It is accompanied by an audible signal and a message on the screen.
Depending on your version of instrument panel, illumination of the
deactivation lamp is also accompanied by:
a symbol in the central instrument panel screen and a message in
the multifunction screen,
or
a symbol and a message in the central instrument panel screen.
32
Warning lamp
Passenger's
front airbag
is on
fixed, in the seat
belt and front
passenger's
airbag warning
lamps display.
Cause
The control switch, located
on the passenger's end of
the dashboard, is set to the
OFF position.
The passenger's front airbag is
deactivated.
You can install a "rearward
facing" child seat on the front
seat.
Action / Observations
Before installing a "rearward facing" child seat on the front
seat, it is essential to deactivate the passenger's front
airbag.
On the other hand, where no "rearward facing" child seat is
present, it is recommended that the airbag be reactivated:
set the control to the ON position.
COOLANT TEMPERATURE INDICATOR
After driving for a few minutes, the temperature and pressure in the
cooling system increase.
To top up the level:
 wait for the engine to cool,
 unscrew the cap by two turns to allow the pressure to drop,
 when the pressure has dropped, remove the cap,
 top up the level to the "MAX" mark.
With the engine running, when the needle is:
in zone A, the temperature is correct,
in zone B, the temperature is too high; the maximum temperature
warning lamp and the central STOP warning lamp come on,
accompanied by an audible signal and an alert message in the
screen.
You MUST stop as soon as it is safe to do so.
Wait a few minutes before switching off the engine.
Contact a PEUGEOT dealer or a qualified workshop.
This information is displayed for a few seconds when the ignition is
switched on, at the same time as the service information.
The check of this level is only valid if the vehicle is on a level
surface, with the engine having been off for more than 30 minutes.
1/ MONITORING
ENGINE OIL LEVEL INDICATOR
Oil level correct
34
Lack of oil
This is indicated by the flashing of "OIL" or an alert message in the
instrument panel, accompanied by illumination of the service warning
lamp and an audible signal.
If the lack of oil is confirmed by a check using the dipstick, it is essential
that the level is topped up to prevent damage to the engine.
Refer to the "Checking levels" section.
Indicator fault
This is indicated by the flashing of "OIL--" or the appearance of an alert
message in the instrument panel.
Contact a PEUGEOT dealer or a qualified workshop.
In the event of a fault with the electric gauge, the oil level is no longer
monitored.
If the system is faulty, you should check the engine oil level using the
dipstick under the bonnet.
Refer to the "Checking levels" section.
SERVICE INDICATOR
Less than 600 miles (1 000 km) remain before the next service is due
This information is displayed for a few seconds when the ignition is
switched on. It informs the driver when the next service is due, in
accordance with the manufacturer's servicing schedule.
The point at which the service is due is calculated from the last indicator
zero reset. It is determined by two parameters:
the distance travelled,
the time elapsed since the last service.
Example: 500 miles remain before the next service is due.
For 7 seconds after the ignition is switched on, the central screen
indicates:
More than 1 800 miles (3 000 km) remain before the next service is due
When the ignition is switched on, no service information appears on the
instrument panel central screen.
The spanner remains on in the small screen
to indicate that a service must be carried out
soon.
For 7 seconds after the ignition is switched on, the spanner symbolising
the service operations comes on. The instrument panel central screen
indicates the distance remaining before the next service is due.
Example: 1 700 miles remain before the next service is due.
For 7 seconds after the ignition is switched on, the central screen
indicates:
1/ MONITORING
Between 600 miles (1 000 km) and 1 800 miles (3 000 km)
remain before the next service is due
Service indicator zero reset
Service overdue
For 7 seconds after the ignition is switched on, the spanner flashes to
indicate that the service must be carried out as soon as possible.
Example: the service is overdue by 300 miles.
For 7 seconds after the ignition is switched on, the central screen
indicates:
36
The spanner remains on in the small screen
to indicate that a service should have been
carried out.
The distance remaining may be weighted by the time factor,
depending on the type of motoring the vehicle is used for.
Therefore, the spanner may also come on if you have exceeded
the period since the last service specified in the warranty and
maintenance record.
After each service, the service indicator must be reset to zero.
The procedure for resetting to zero is as follows:
 switch off the ignition,
 press and hold the "CHECK/000" button,
 switch on the ignition; the distance recorder display begins a
countdown,
 when the instrument panel central screen indicates "=0", release
the button; the spanner disappears from the small screen.
Following this operation, if you wish to disconnect the battery, lock
the vehicle and wait at least five minutes for the zero reset to be
registered.
Retrieving the service information
You can access the service information at any time.
This information appears when running through the manual check
procedure.
 Briefly press the "CHECK/000" button.
The service information is displayed for a few seconds on the
instrument panel central screen, then disappears.
MANUAL CHECK
DISTANCE RECORDERS
This function allows you to check the status of the vehicle (reminder of
the active alert warnings) and the service information.
The total and trip distances are displayed for thirty seconds when the
ignition is switched off, when the driver's door is opened and when the
vehicle is locked or unlocked.
Total distance recorder
 With the engine running, to start a manual check, briefly press the
"CHECK/000" button on the instrument panel.
If no faults have been detected, "CHECK OK" appears in the
instrument panel central screen.
If a "minor" fault has been detected, the warning lamp concerned then
"CHECK OK" appear in the instrument panel central screen. Contact a
PEUGEOT or a qualified workshop.
If a "major" fault has been detected, only the warning lamps concerned
appear in the instrument panel central screen. Have it checked by a
PEUGEOT dealer or a qualified workshop.
Trip distance recorder
Measures the distance travelled since it was last reset to zero by the
driver.
 With the ignition on, press and hold this button until zeros appear.
1/ MONITORING
Measures the total distance travelled by the vehicle since its first
registration.
LIGHTING DIMMER
CLOCK
38
Permits manual adjustment of the brightness of the instruments and
controls to suit the ambient light level. Only operates when the vehicle
lighting is on, with the exception of the daytime running lamps.
Activation
 Press the button to change the brightness of the instruments and
controls.
 When the lighting reaches the minimum setting, release the button,
then press again to increase it.
or
 When the lighting reaches the maximum setting, release the button,
then press again to reduce it.
 When the lighting reaches the level of brightness required, release
the button.
Deactivation
When the vehicle lighting is off, or in day mode on vehicles fitted with
daytime running lamps, pressing the button does not have any effect.
The analogue clock, located between the central vents of the
dashboard, does not have an adjustment button.
To set the time, refer to the section relating to your multifunction
screen's configuration menu.
The clock is synchronised with the multifunction screen time; once the
the setting has been confirmed on the multifunction screen, the hands
will turn to synchronise with the screen, and each time the ignition is
switched on.
TRIP COMPUTER
System that gives you information on the journey in progress (range,
fuel consumption…).
DATA DISPLAYS
With the small central screen
Instrument panel with small central screen
 Press the button, located at the end of the wiper stalk, to display
the various trip computer tabs in succession.
Instrument panel with large central screen
 Press the up and down arrows on the navigator for the instrument
panel with large central screen to display the various trip computer
tabs in succession.
1/ MONITORING
With the large central screen
-
40
1
2
-
-
The current information tab with:
● the range,
● the current fuel consumption.
The trip "1" tab with:
● the distance travelled,
● the average fuel consumption,
● the average speed,
for the first trip.
The trip "2" tab with:
● the distance travelled,
● the average fuel consumption,
● the average speed,
for the second trip.
TRIP ZERO RESET
With the small central screen
 When the trip required is displayed, press the button at the end of
the wiper stalk for more than two seconds.
With the large central screen
 Pressing the button again takes you to a black screen.
A further press returns you to the normal display.
With the large screen, the trip computer also includes a tab for the
current speed and a tab to repeat the navigation instructions.
 When the required trip is displayed, press the "OK" button on the
navigator for the instrument panel with large central screen.
Trips "1" and "2" are independent but their use is identical.
For example, trip "1" can be used for daily figures, and trip "2" for
monthly figures.
Range
(miles or km)
The distance which can still be travelled with the fuel
remaining in the tank (related to the average fuel consumption over the
last few miles (kilometres) travelled).
This value may vary following a change in the style of driving
or the relief, resulting in a significant change in the current fuel
consumption.
When the range falls below 20 miles (30 km), dashes are displayed.
After filling with at least 5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (100 km).
If dashes are displayed continuously while driving in place of the
digits, contact a PEUGEOT dealer or a qualified workshop.
Current fuel consumption
(mpg or l/100 km or km/l)
Calculated over the last few seconds.
This function is only displayed from 20 mph (30 km/h).
Average fuel consumption
(mpg or l/100 km or km/l)
Calculated since the last trip computer reset.
Average speed
(mph or km/h)
Calculated since the last trip computer reset.
Distance travelled
(miles or km)
Calculated since the last trip computer reset.
1/ MONITORING
TRIP COMPUTER, A FEW DEFINITIONS
MONOCHROME SCREEN C (WITH
PEUGEOT CONNECT SOUND (RD5))
42
DISPLAYS IN THE SCREEN
Displays according to context:
time,
date,
ambient temperature with air conditioning (the value displayed
flashes if there is a risk of ice),
visual parking assistance,
audio functions,
alert messages,
the display and vehicle equipment settings menus.
CONTROLS
From the control panel of your PEUGEOT Connect Sound (RD5), you
can:
 press the "MENU" button for access to the main menu,
 press the "" or "" buttons to scroll through the items on the
screen,
 press the "MODE" button to change the permanent application
(audio source, telephone...),
 press the "" or "" buttons to change a setting value,
 press the "OK" button to confirm,
or
 press the "Back" button to abandon the operation in progress.
MAIN MENU
"DIAGNOSIS VEHICLE" MENU
Once this menu has been selected, you can consult information
concerning the status of the vehicle.
 Press the "MENU" button to gain access to the main menu:
- audio functions,
- vehicle diagnostics,
- personalisation-configuration,
- telephone (Bluetooth system).
 Press the "" or "" buttons to select the menu required, then
confirm by pressing the "OK" button.
Alert log
This summarises the active warning messages, displaying them in
succession on the multifunction screen.
 Press the "MENU" button to gain access to the main menu.
 Press the arrows, then the "OK" button to select the "Diagnosis
vehicle" menu.
With the PEUGEOT Connect Sound (RD5) switched on, once this menu
has been selected you can activate or deactivate the functions linked
with use of the radio (RDS, REG, RadioText) or the CD (introscan,
shuffle, CD repeat).
For more information on the "Audio functions" application, refer to the
PEUGEOT Connect Sound (RD5) section.
 On the "Diagnosis vehicle" menu, select the following application:
1/ MONITORING
"AUDIO FUNCTIONS" MENU
Example: setting of the duration of the guide-me-home lighting
 Press the "" or "" buttons, then the "OK" button to select the
menu required.
 Press the "" or "" buttons, then the "OK" button to select the
"Guide-me-home headlamps" line.
44
"PERSONALISATION-CONFIGURATION"
MENU
Once this menu has been selected, you can gain access to the
following functions:
define the vehicle parameters,
display configuration,
choice of language.
 Press the "" or "" buttons to set the value required (15, 30 or
60 seconds), then press the "OK" button to confirm.
Define the vehicle parameters*
Once this menu has been selected, you can activate or deactivate the
following equipment:
selective unlocking (refer to the "Access" section),
guide-me-home lighting (refer to the "Visibility" section),
interior mood lighting (refer to the "Ease of use and comfort" section),
daytime running lamps** (refer to the "Visibility" section),
rear parking sensors (refer to the "Driving" section).
 Press the "" or "" buttons, then the "OK" button to select the
"OK" box and confirm or press the "Back" button to cancel.
* Depending on version.
** Depending on country of sale.
Once this menu has been selected, you have access to the following
settings:
brightness-video setting,
date and time setting,
choice of units.
Setting the date and time
 Press the "" or "" button to display the "Display configuration"
menu, then the "OK" button.
 Press the "" or "" button to select the "Adjust date and time"
line, then the "OK" button.
 Press the "" or "" button to select the setting to modify. Confirm
by pressing the "OK" button then modify the setting and confirm
again to save the modification.
 Adjust the settings one by one, confirming with the "OK" button.
 Press the "" or "" button, then the "OK" button to select the
"OK" box and confirm, or the "Back" button to cancel.
"TELEPHONE" MENU
With the PEUGEOT Connect Sound (RD5) switched on, once this menu
has been selected you can configure your Bluetooth hands-free system
(pairing), consult the various telephone directories (calls log, services...)
and manage your communications (pick up, hang up, call waiting,
secret mode...).
For more information on the "Telephone" application, refer to the
PEUGEOT Connect Sound (RD5) section.
For safety reasons, configuration of the multifunction screen by
the driver must only be done when stationary.
Choice of language
Once this menu has been selected, you can change the language
used by the display (Deutsch, English, Espanol, Français, Italiano,
Nederlands, Portugues, Portugues-Brasil, Türkçe*).
* According to country of sale.
1/ MONITORING
Display configuration
RETRACTABLE COLOUR SCREEN (WITH
PEUGEOT CONNECT NAVIGATION (RT6))
46
DISPLAYS IN THE SCREEN
Displays according to context:
time,
date,
altitude,
ambient temperature (the value displayed flashes if there is a risk of
ice),
parking sensor information,
audio functions,
telephone and contacts information,
satellite navigation system information,
alert messages,
menus for settings of the screen, navigation system and vehicle
equipment.
CONTROLS
From the navigation system control panel, to select one of the
applications:
 press the dedicated "RADIO", "MUSIC", "NAV", "TRAFFIC",
"PHONE" or "SETUP" button for access to the corresponding
menu,
 turn dial A to select a function, an item in a list,
 press button B to confirm the selection,
or
 press the "Back" button to abandon the current operation and
return to the previous display.
For more information on these applications, refer to the "Audio
equipment and telematics" section.
For operation of the retractable screen (opening, closing,
adjustment of the position, etc.), refer to the "Access to the
retractable screen" section.
"SETUP" MENU
 Select the setting to modify. Conform by pressing "OK", then adjust
the setting and modify again.
 Adjust the settings one by one.
 Select "OK" in the screen then confirm to save the setting.
Voice synthesis
This men allows you to adjust the volume for navigation instructions and
to choose the type of voice (male or female).
Choice of language
For safety reasons, configuration of the multifunction screen by
the driver must only be done when stationary.
Display configuration
This menu allows you to choose a colour scheme for the screen, to
adjust the brightness, set the date and time and choose the units for
distance (km or miles), fuel consumption (l/100 km, mpg or km/l) and
temperature (°Centigrade or °Fahrenheit).
Setting the date and time
 Press "SETUP".
 Select "Display configuration" and confirm.
 Select "Set date and time" and confirm.
You can select "Synchronise the minutes with GPS", so that the
minutes are adjusted automatically by satellite reception.
This menu allows you to choose the language used by the screen
(French, English, Italian, Portuguese, Spanish, German, Dutch, Turkish,
Polish, Russian).
Vehicle parameters*
This menu allows you to activate or deactivate certain driving and
comfort equipment, arranged by category:
Access to the vehicle
● Selective unlocking of the driver's door; refer to "Access"),
Parking sensors
Operation of wipers
● Rear wiper linked to reverse (rear wiper operates in reverse gear;
refer to "Visibility"),
Lighting configuration (see "Visibility"):
● Duration of the guide-me-home lighting,
● Directional headlamps (main/additional directional lighting),
● Mood lighting (Interior mood lighting),
● Daytime running lamps function**.
Alert log
It lists the active alerts by displaying their associated messages in turn.
* Depending on version.
** According to country of sale.
1/ MONITORING
 Press the "SETUP" button to gain access to the configuration
menu:
- "Display configuration",
- "Voice synthesis",
- "Choice of language",
- "Vehicle parameters",
- "Alert log".
RETRACTABLE COLOUR SCREEN (WITH PEUGEOT
CONNECT MEDIA NAVIGATION (NG4 3D))
CONTROLS
48
DISPLAYS IN THE SCREEN
Displays according to context:
time,
date,
altitude,
ambient temperature (the value displayed flashes if there is a risk of
ice),
parking sensor information,
audio functions,
telephone and address book information,
satellite navigation system information.
display screen or navigation system parameter settings menus.
From the PEUGEOT Connect Media Navigation (NG4 3D) control
panel, to select one of the applications:
 press the dedicated "RADIO", "MEDIA", "NAV", "TRAFFIC",
"ADDR BOOK" or "SETUP" button for access to the
corresponding menu,
 turn dial A to select a function, an item in a list,
 press button B to confirm the selection,
or
 press the "Back" button to abandon the current operation and
return to the previous display.
For more information on these applications, refer to the PEUGEOT
Connect Media Navigation (NG4 3D) section.
Date and time
This menu allows you to set the date and time, the format of the date
and the format of the time.
"SETUP" MENU
Principle of GPS (GMT) synchronisation:
1. Confirm the selection "Synchronise with GPS", the time is then
aligned with GMT universal time, the date is updated as well.
2. Using the 4-direction navigator, move the cursor onto the hours field
and press on OK.
3. Using the rotating ring, you can then adjust the time to the time
zone of your choice.
Note that in the case of a summer/winter time change, the time
zone must be set again manually.
 Press the "SETUP" button to gain access to the "SETUP" menu.
This allows you to select from the following functions:
- "Language and speech",
- "Date and time",
- "Display",
- "Units",
- "System".
Display
Language and speech
This menu allows you to:
select the language used by the display (Deutsch, English,
Espanol, Français, Italiano, Nederlands, Polski, Portugues,
Portugues-Brasil, Türkçe*),
select the voice recognition parameters (activation/deactivation,
advice on use, personal voice programming, etc.),
set the volume of the voice synthesiser.
This menu allows you to set the brightness of the screen, the screen
colour scheme and the colour of the map (day/night or auto mode).
Units
This menu allows you to select the units: temperature (°C or °F) and
distance (miles or km).
System
This menu allows you to restore the factory configuration, display the
software version and activate scrolling text.
For safety reasons, configuration of the multifunction screen by
the driver must only be done when stationary.
* Depending on country of sale.
1/ MONITORING
For operation of the retractable screen (opening, closing,
adjustment of the position, etc.), refer to the "Access to the
retractable screen" section.
ACCESS TO THE RETRACTABLE SCREEN
50
The screen opens automatically when the ignition is switched on. It
closes automatically three seconds after switching off the ignition if the
audio and telematics system is switched off.
You can open or close the screen at any time, with the ignition on, using
control A.
Press button A: the screen folds.
Press button A again: the screen opens again.
If you have closed the screen, it will open again automatically:
on switching on the audio and navigation system (unless it
had been closed manually while the system was in operation),
when an outgoing telephone call is made,
when a voice command is given,
when a warning message linked with the STOP warning lamp
is displayed (PEUGEOT Connect Navigation (RT6)).
Adjusting the angle of the screen
You can adjust the angle of the screen to one of four defined positions,
by repeated presses on the front or back of the control B. The position
of the screen is memorised on closing.
REMOTE CONTROL KEY
System which permits central unlocking or locking of the vehicle using
the lock or from a distance. It is also used to locate and start the
vehicle, as well as providing protection against theft.
Selective unlocking using the remote control
 Press the open padlock once to unlock the driver's door
and the fuel filler flap only.
 Press the open padlock again to unlock the passenger's door and
the boot.
Selective unlocking using the key
 Turn the key forwards in the driver's door lock once to unlock the
driver's door and the fuel filler flap only.
 Turn the key forwards in the driver's door lock again to unlock the
passenger's door and the boot.
UNLOCKING THE VEHICLE
Unfolding the key
The direction indicators flash for a few seconds.
Depending on version, the door mirrors unfold, the alarm is deactivated.
 First press this button to unfold the key.
 Press the open padlock to unlock the vehicle.
Complete unlocking using the key
 Turn the key forwards in the driver's door lock to unlock the vehicle.
The complete or selective unlocking parameter is set via
the vehicle configuration menu.
Complete unlocking is activated by default.
Unlocking and partial opening of the boot
 Press this button for more than two seconds to unlock
the boot. The boot opens slightly.
This action also unlocks the doors and the fuel filler flap.
2/ ACCESS
Complete unlocking using the remote control
LOCKING THE VEHICLE
Normal locking using the remote control
 Press the closed padlock to lock the vehicle completely.
Deadlocking using the remote control
 Press the closed padlock to lock the vehicle completely.
 Press the closed padlock again within five seconds to
deadlock the vehicle.
Normal locking using the key
Deadlocking using the key
 Turn the key rearwards in the driver's door lock to lock the vehicle
completely.
 Turn the key rearwards in the driver's door lock to lock the vehicle
completely.
 Turn the key rearwards again within five seconds to deadlock the
vehicle.
52
The direction indicators come on for a few seconds.
Depending on version, the door mirrors fold, the alarm is activated.
If one of the doors or the boot is still open, the central locking does
not take place; the vehicle lock and then immediately unlocks,
witnessed by the sound of the locks rebounding. However,
the alarm (if fitted) will be completely activated after about
45 seconds.
When the vehicle is locked, if it is unlocked inadvertently, it will
lock itself again automatically after thirty seconds unless a door is
opened.
If the alarm had been activated previously, it will not be reactivated
automatically.
The folding and unfolding of the door mirrors using the remote
control can be deactivated by a PEUGEOT dealer or a qualified
workshop.
The direction indicators come on for a few seconds.
Depending on version, the door mirrors fold, the alarm is
activated.
Deadlocking renders the exterior and interior door controls
inoperative.
It also deactivates the manual central control button.
Therefore, never leave anyone inside the vehicle when it is
deadlocked.
Reinitialisation
 Switch off the ignition.
 Turn the key to position 2 (Ignition on).
 Press the closed padlock immediately for a few seconds.
 Switch off the ignition and remove the key from the ignition switch.
The remote control is fully operational again.
Folding the key
 First press this button to fold the key.
LOCATING YOUR VEHICLE
This function allows you to identify your vehicle from a
distance, particularly in poor light. Your vehicle must be
locked.
REMOTE CONTROL PROBLEM
Following disconnection of the vehicle battery, replacement of the
remote control battery or in the event of a remote control malfunction,
you can no longer unlock, lock or locate your vehicle.
 First of all, use the key in the lock to unlock or lock your vehicle.
 Then, reinitialise the remote control.
If the problem persists, contact a PEUGEOT dealer as soon as
possible.
Changing the battery
Battery ref.: CR1620 / 3 volts.
If the battery is flat, you are informed by illumination of this
warning lamp, accompanied by an audible signal and an alert
message in the screen.
 Unclip the casing using a coin at the notch.
 Slide the flat battery out of its location.
 Slide the new battery into its location observing the original
direction.
 Clip the casing.
 Reinitialise the remote control.
2/ ACCESS
 Press the closed padlock on the remote control.
This will switch on the courtesy lamps and the direction indicators will
flash for around ten seconds.
LOST KEYS
Go to a PEUGEOT dealer with the vehicle's registration document, your personal identification documents and if possible the key code label.
The PEUGEOT dealer will be able to look up the key code and the transponder code required to order a new key.
REMOTE CONTROL
The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a possibility that it may unlock
the vehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and out of sight of your vehicle. You run the risk of stopping it from
working and the remote control would have to be reinitialised.
No remote control can operate when the key is in the ignition switch, even when the ignition is switched off, except for reinitialisation.
54
LOCKING THE VEHICLE
Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult in an emergency.
As a safety precaution, never leave children alone in the vehicle, except for a very short period.
In all cases, it is essential to remove the key from the ignition switch when leaving the vehicle.
ANTI-THEFT PROTECTION
Do not make any modifications to the electronic engine immobiliser system; this could cause malfunctions.
WHEN PURCHASING A SECOND-HAND VEHICLE
Have the pairing of all of the keys in your possession checked by a PEUGEOT dealer, to ensure that only your keys can be used to open and
start the vehicle.
Do not throw the remote control batteries away, they contain metals which are harmful to the environment.
Take them to an approved collection point.
ALARM*
System which protects and provides a deterrent against theft and
break-ins. It provides the following types of monitoring.
-
LOCKING THE VEHICLE WITH FULL ALARM
SYSTEM
exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a door, the boot, the
bonnet...
interior volumetric
The system checks for any variation in the volume in the passenger compartment.
The alarm is triggered if anyone breaks a window, enters the passenger
compartment or moves inside the vehicle.
-
tilt
The system checks for any change in the attitude of the vehicle.
The alarm is triggered if the vehicle is lifted, moved or knocked.
Self-protection function
The system checks for the putting out of service of its
components.
The alarm is triggered if the battery, the central control or the siren
wiring are put out of service or damaged.
For all work on the alarm system, contact a PEUGEOT dealer or a
qualified workshop.
* According to country.
Activation
 Switch off the ignition and get out of the vehicle.
 Press the locking button on the remote control.
The monitoring system is active: the indicator lamp in the button flashes
once per second.
After the locking button on the remote control is pressed, the exterior
perimeter monitoring is activated after a delay of 5 seconds and the
interior volumetric and anti-tilt monitoring after a delay of 45 seconds.
If an opening (door, boot...) is not closed fully, the vehicle is not
locked but the exterior perimeter monitoring will be activated after
a delay of 45 seconds at the same time as the interior volumetric
and anti-tilt monitoring.
Deactivation
 Press the unlocking button on the remote control.
The alarm system is deactivated: the indicator lamp in the button goes off.
2/ ACCESS
-
56
LOCKING THE VEHICLE WITH EXTERIOR
PERIMETER MONITORING ONLY
Deactivate the interior volumetric and anti-tilt monitoring to avoid
unwanted triggering of the alarm in certain cases such as:
leaving a pet in the vehicle,
leaving a window partially open,
washing your vehicle,
changing a wheel,
having your vehicle towed,
transport by sea.
Deactivation of the interior volumetric and anti-tilt monitoring
 Switch off the ignition.
 Within ten seconds, press the button until the indicator lamp is on
continuously.
 Get out of the vehicle.
 Press the locking button on the remote control immediately.
The exterior perimeter monitoring alone is activated: the indicator lamp
in the button flashes once per second.
To be effective, this deactivation must be carried out each time the
ignition is switched off.
Reactivation of the interior volumetric and anti-tilt monitoring
 Press the unlocking button on the remote control to deactivate the
exterior perimeter monitoring.
 Press the locking button on the remote control to activate all the
monitoring functions.
The indicator lamp in the button again flashes once per second.
This is indicated by sounding of the siren and flashing of the direction
indicators for thirty seconds.
The monitoring functions remain active until the alarm has been
triggered eleven times in succession.
When the vehicle is unlocked using the remote control, rapid
flashing of the indicator lamp in the button informs you that the
alarm was triggered during your absence. When the ignition is
switched on, this flashing stops immediately.
LOCKING THE VEHICLE WITHOUT ACTIVATING
THE ALARM
 Lock or deadlock the vehicle using the key in the driver's door lock.
OPERATING FAULT
When the ignition is switched on, fixed illumination of the indicator lamp
in the button indicates a fault with the system.
Have it checked by a PEUGEOT dealer or a qualified workshop.
FAILURE OF THE REMOTE CONTROL
AUTOMATIC ACTIVATION*
To deactivate the monitoring functions:
2 minutes after closing the last door or the boot, the system is activated
automatically.
 To avoid triggering the alarm when entering the vehicle, first press
the remote control unlocking button.
 unlock the vehicle using the key in the driver's door lock,
 open the door; the alarm is triggered,
 switch on the ignition; the alarm stops; the indicator lamp in the
button goes off.
* Depending on country of sale.
2/ ACCESS
TRIGGERING OF THE ALARM
ELECTRIC WINDOWS
Fitted with a safety anti-pinch system.
The electric window switches remain operational for approximately
45 seconds after the ignition is switched off or until the vehicle is
locked after a door is opened.
If the passenger's window cannot be operated from the driver's
door control panel, carry out the operation from the control panel
of the passenger door.
58
After approximately ten consecutive complete opening/closing
movements of the window, a protection function is activated which
only authorises closing of the windows, so as to prevent damage
to the electric window motor.
Once the window is closed, the switches will become operational
again after approximately 40 minutes.
A. Left-hand electric window.
B. Right-hand electric window.
ONE-TOUCH ELECTRIC WINDOWS
There are two options:
manual mode
 Press or pull the switch gently. The window stops when the
switch is released.
automatic mode
 Press or pull the switch firmly. The window opens or closes fully
when the switch is released.
 Pressing the switch again stops the movement of the window.
Safety anti-pinch
When the window rises and meets an obstacle, it stops and partially
lowers again.
If the window cannot be closed (for example, in the presence of
ice), immediately after the movement is reversed:
 press and hold the switch until the window opens fully,
 then pull the switch immediately and hold it until the window
closes,
 continue to hold the switch for approximately one second after
the window has closed.
The safety anti-pinch function is not operational during these
operations.
If a window does not rise automatically, after reconnecting the battery
for example, its operation must be reinitialised:
 pull the switch until the window stops,
 release the switch and pull it again until the window closes fully,
 continue to hold the switch for approximately one second after the
window has closed,
 press the switch to lower the window automatically to the low
position,
 when the window has reached the low position, press the switch
again for approximately one second.
The safety anti-pinch function is not operational during these
operations.
Always remove the key from the ignition when leaving the vehicle,
even for a short time.
If an obstacle is encountered during operation of the electric
windows, you must reverse the movement of the window. To do
this, press the switch concerned.
When the driver operates the switch for the passenger's electric
window, they must ensure that no one is preventing correct
closing of the windows.
The driver must ensure that the passengers use the electric
windows correctly.
Be aware of children when operating the windows.
2/ ACCESS
Reinitialisation
DOORS
From inside
OPENING
60
From outside
 After unlocking the vehicle completely using the remote control or
the key, take hold of the door handle then pull it.
The window lowers automatically by a few millimetres to permit
opening of the door.
 Pull the door control to open the door; this unlocks this vehicle
completely.
The window lowers automatically by a few millimetres to permit
opening of the door.
If you leave the door open for more than one minute, the window
rises again.
Pull the handle again to reactivate the system.
With the selective unlocking activated:
the driver's door control unlocks the driver's door and the fuel
filler flap only.
the passenger's door control unlocks the passenger's door
and the boot.
In freezing conditions, the presence of ice may hinder the automatic
partial opening of the window; remove the ice which may have
formed along the lower seal, located at the base of the window.
The interior door controls do not operate when the vehicle is
deadlocked.
When the selective unlocking is activated, the first press of the
remote control unlocking button permits unlocking of the driver's
door only.
CLOSING
CENTRAL LOCKING CONTROL
The window rises automatically after a few seconds and adjusts to
provide perfect sealing when closed.
This control permits simultaneous locking or unlocking of the doors,
boot lid and fuel filler flap from inside the vehicle.
Be aware of the risk of pinching when the window rises
automatically on closing the door.
When a door is not closed correctly:
-
when the engine is running, this warning lamp comes on,
accompanied by a message in the screen for a few seconds,
when the vehicle is moving (speed higher than 6 mph (10 km/h)),
this warning lamp comes on, accompanied by an audible signal and
a message in the screen for a few seconds.
When washing your vehicle:
first lock the vehicle using the remote control or the key,
avoid spraying the upper part of the windows,
keep the end of the high pressure nozzle at least 1 metre from
the windows and door seals.
Locking
 Press this button to lock the vehicle.
The red indicator lamp on the button comes on.
If one of the doors or the boot lid is open, the central locking from
the inside does not take place.
Unlocking
 Press this button again to unlock the vehicle.
The red indicator lamp on the button goes off.
Locking / deadlocking from the outside
When the vehicle is locked or deadlocked from the outside, the
red indicator lamp flashes and the button is inactive.
 With normal locking, pull on the interior door control lever to
unlock the vehicle.
 With deadlocking, you have to use the remote control or the
key to unlock the vehicle.
2/ ACCESS
-
ANTI-INTRUSION SECURITY
EMERGENCY LOCKING
This function permits automatic and simultaneous locking of the doors,
boot lid and fuel filler flap as soon as the vehicle speed exceeds 6 mph
(10 km/h).
To lock or unlock the doors mechanically in the event of a central
locking system failure or flat battery.
Operation
Locking the driver's door
If one of the doors is open, the automatic central locking does not take
place.
If the boot lid is open, the automatic central locking of the doors is
active.
 Insert the key in the lock, then turn it to the right.
62
Pressing the central locking control unlocks the vehicle.
Opening a door from the inside, when stationary, also unlocks the
vehicle, but the vehicle will be locked again when the speed exceeds
6 mph (10 km/h).
Unlocking the driver's door
 Insert the key in the lock, then turn it to the left.
Locking the passenger door
Activation / Deactivation
You can activate or deactivate this function.
 With the ignition on, press the button for more than two seconds.
A confirmation message appears in the screen.
 Using the key, remove the black cap on the edge of the door.
 Insert the key in the cavity without forcing, then without turning it,
move the the latch sideways towards the interior of the door.
 Remove the key and refit the cap.
Unlocking the passenger door
 Pull the interior door opening control.
BOOT
OPENING
CLOSING
 Lower the boot lid using one of the interior grab handles.
 If necessary, press the top of the boot lid to close it fully.
Using the remote control
 Press this button for more than two seconds to unlock
the boot lid. The boot lid opens slightly.
 Lift the boot lid.
Never grasp the boot lid by the active spoiler.
This action also unlocks the doors and the fuel filler flap.
Using the manual control; vehicle unlocked
 Press the opening control above the number plate.
 Lift the boot lid.
-
-
When selective unlocking is activated, the boot can also be
opened by a second press on the open padlock on the remote
control.
when the engine is running, this warning lamp comes on,
accompanied by a message in the screen for a few seconds,
when the vehicle is moving (speed above 6 mph (10 km/h)), this
warning lamp comes on, accompanied by an audible signal and a
message in the screen for a few seconds.
Emergency locking
If the central locking system fails (flat battery), you are advised to
disconnect the battery.
2/ ACCESS
If the boot lid is not closed correctly:
FRONT SEATS
Driver's or passenger's seat height adjustment
Seat with integral head restraint, consisting of a seat cushion and a seat
back which can be adjusted to adapt your position for ease of driving
and comfort.
MANUAL ADJUSTMENTS
Forwards-backwards adjustment
64
 Pull the control lever upwards to raise or push it downwards to
lower, as many times as necessary, to obtain the position required.
Seat back angle adjustment
 Raise the control bar and slide the seat forwards or backwards.
Before moving the seat backwards, ensure that there is nothing
that might prevent the full travel of the seat, so as to avoid the risk
of of jamming the seat caused by the presence of objects on the
floor behind the seat or rear passengers. If the seat jams, stop the
movement immediately.
 Turn the knob to set the angle required.
FRONT SEATS
Seat cushion height adjustment
The electrical functions of the seat are deactivated approximately
one minute after the ignition is switched off.
To reactivate them, switch on the ignition.
Carry out these adjustments with the engine running to avoid
discharging the battery.
ELECTRIC ADJUSTMENTS
Forwards-backwards adjustment
 Tilt the rear part of the control upwards or downwards to obtain the
required height.
Seat back angle adjustment
 Push the control forwards or rearwards to slide the seat.
Before moving the seat backwards, ensure that there is nothing
that might prevent the full travel of the seat, so as to avoid the risk
of of jamming the seat caused by the presence of objects on the
floor behind the seat or rear passengers. If the seat jams, stop the
movement immediately.
 Tilt the control forwards or rearwards to adjust the angle of the seat
back.
3/ EASE OF USE and COMFORT
Seat with integral head restraint,consisting of a seat cushion and a seat
back which can be adjusted to adapt your position for ease of driving
and comfort.
66
MANUAL LUMBAR ADJUSTMENT
Heated seats control
 Turn the knob manually to obtain the desired level of lumbar
support.
With the engine running, the front seats can be heated separately.
 Use the adjustment dial, placed on the side of each front seat, to
switch on and select the level of heating required:
0: Off.
1: Low.
2: Medium.
3: High.
STORING DRIVING POSITIONS
RECALLING A STORED POSITION
System which takes into account the electrical settings of the driver's
seat and the door mirrors. It enables you to store two positions using
the buttons on the side of the driver's seat.
Using button 1 or 2
Using buttons M / 1 / 2
 Switch on the ignition.
 Adjust your seat and your door mirrors.
 Press button M, then press button 1 or 2 within four seconds.
An audible signal is heard indicating that the settings have
been stored.
Storing a new position cancels the previous position.
When the ignition is off, after a few consecutive position recalls,
the function will be deactivated until the engine is started, to
prevent discharging of the battery.
3/ EASE OF USE and COMFORT
STORING A POSITION
 Press and hold button 1 or 2 until the audible signal is heard
indicating the end of the adjustment.
68
STEERING WHEEL ADJUSTMENT
 When stationary, pull the control lever to release the adjustment
mechanism.
 Adjust the height and reach to suit your driving position.
 Push the control lever to lock the adjustment mechanism.
As a safety precaution, these operations should only be carried
out with the vehicle stationary.
Adjustment
DOOR MIRRORS
 Move control A to the right or to the left to select the corresponding
mirror.
 Move control B in all four directions to adjust.
 Return control A to the central position.
Each fitted with an adjustable mirror glass permitting the lateral
rearward vision necessary for overtaking or parking. They can be
folded electrically.
Demisting - defrosting
The demisting-defrosting of the door mirrors is effected with
the engine running, by switching on the heated rear screen
(refer to the "Demisting-defrosting the rear screen" section).
The objects observed are, in reality, closer than they appear.
Take this into account in order to correctly judge the distance of
vehicles approaching from behind.
3/ EASE OF USE and COMFORT
MIRRORS
Folding
Programming
 From outside: lock the vehicle using the remote control or the key.
 From inside: with the ignition on, pull the control A in the central
position rearwards.
 With the engine running, engage reverse gear.
 Select and adjust the left-hand and right-hand mirrors in
succession.
The adjustment is stored immediately.
If the mirrors are folded using control A, they will not unfold when
the vehicle is unlocked. Pull again on control A.
Unfolding
70
 From outside: unlock the vehicle using the remote control or the
key.
 From inside: with the ignition on, pull the control A in the central
position rearwards.
The folding and unfolding of the door mirrors using the remote
control can be deactivated by a PEUGEOT dealer or a qualified
workshop.
If necessary the mirrors can be folded manually.
Automatic tilting in reverse gear
System which provides a view of the ground during parking
manoeuvres in reverse gear.
Switching on
 With the engine running, engage reverse gear.
 Move control A to the right or to the left to select the corresponding
mirror.
The glass of the mirror selected tilts downwards, in accordance with its
programming.
Switching off
 Exit reverse gear and wait ten seconds.
or
 Return control A to the central position.
The mirror glass returns to its initial position.
The mirror glass also returns to its initial position:
if the speed exceeds 6 mph (10 km/h),
if the engine is switched off.
Adjustable mirror providing a central rearward view.
Equipped with an anti-dazzle system, which darkens the mirror glass
and reduces the nuisance to the driver caused by the sun, headlamps
from other vehicles...
As a safety measure, the mirrors should be adjusted to reduce
the "blind spot".
Automatic day/night model
By means of a sensor, which measures the light from the rear of the
vehicle, this system automatically and progressively changes between
the day and night uses.
In order to ensure optimum visibility during your manoeuvres, the
mirror lightens automatically when reverse gear is engaged.
Due to the curve of the rear screen, the image in the rear view
mirror may be slightly distorted; take this into account when
manoeuvring the vehicle.
3/ EASE OF USE and COMFORT
REAR VIEW MIRROR
REAR SEATS
Two-seat bench with one-piece fixed seat cushion and one-piece folding
backrest.
The rear headrests are fixed.
ACCESS TO THE REAR SEATS
72
 Open the boot.
 Pull the backrest release handle, located under the shelf.
 Check that the front seat has been moved forward sufficiently.
 Pull the control upwards to tilt the backrest.
When the seat is put back in place, the backrest returns to its initial position.
FOLDING DOWN THE REAR BACKREST
The backrest can be folded down to increase the boot storage space.
The backrest release control is located in the boot.
 Check that the front seats have been moved forward sufficiently.
 Check that nothing has been left on the rear seats.
 Store the seat belt buckles on their respective securing points
located between the headrests.
 Fold the backrest down onto the seat cushion.
When transporting long objects, do not place a load of more
than 30 kg on the rear of the backrest.
Do not place rough objects on the rear of the backrest which
could damage it.
RETURNING THE REAR BACKREST TO THE UPRIGHT POSITION
When returning the backrest to the upright position, ensure that it is
locked securely to assure your safety.
VENTILATION
AIR INTAKE
AIR FLOW PATHS
The incoming air follows various routes depending on the controls
selected by the driver:
direct arrival in the passenger compartment (air intake),
passage through a heating circuit (heating),
passage through a cooling circuit (air conditioning).
The temperature control enables you to obtain the level of comfort
required by mixing the air of the various circuits.
The air distribution control enables you to diffuse the air in the
passenger compartment combining several air vents.
The air flow control enables you to increase or reduce the speed of the
ventilation blower.
CONTROL PANEL
AIR DIFFUSION
The controls of this system are grouped together on control panel A
on the centre console. The functions offered are:
the level of comfort required,
air flow,
air distribution,
demisting/defrosting,
manual or digital air conditioning controls.
1.
2.
3.
4.
5.
Windscreen demisting/defrosting vents.
Front side window demisting/defrosting vents.
Side adjustable air vents.
Central adjustable air vents.
Air outlets to the front footwells.
3/ EASE OF USE and COMFORT
The air circulating in the passenger compartment is filtered and
originates either from the outside via the grille located at the base of
the windscreen or from the inside in air recirculation mode.
74
RECOMMENDATIONS FOR VENTILATION AND AIR CONDITIONING
In order for these systems to be fully effective, follow the operation
and maintenance guidelines below:
 To obtain an even air distribution, take care not to obstruct
the exterior air intake grilles located at the base of the
windscreen, the nozzles, the vents and the air outlets, as well
as the air extractor located in the boot.
 Do not cover the sunshine sensor, located on the dashboard;
this is used for regulation of the air conditioning system.
 Operate the air conditioning system for at least 5 to 10 minutes,
once or twice a month to keep it in good working order.
 Ensure that the passenger compartment filter is in good
condition and have the filter elements replaced regularly (refer
to the "Checks" section).
We recommend the use of a combined passenger
compartment filter. Thanks to its special active additive,
it contributes to the purification of the air breathed by the
occupants and the cleanliness of the passenger compartment
(reduction of allergic symptoms, bad odours and greasy
deposits).
 To ensure correct operation of the air conditioning system,
you are also advised to refer to the warranty and maintenance
record for information on when it should be checked.
 If the system does not produce cold air, switch it off and
contact a PEUGEOT dealer or a qualified workshop.
When towing the maximum load on a steep gradient in high
temperatures, switching off the air conditioning increases the
available engine power and so improves towing performance.
If after an extended stop in sunshine, the interior temperature is
very high, first ventilate the cabin for a few moments.
Put the air flow control at a setting high enough to quickly change
the air in the cabin.
The air conditioning system does not contain chlorine and does
not present any danger to the ozone layer.
The condensation created by the air conditioning results in a
discharge of water under the vehicle which is perfectly normal.
The air conditioning only operates when the engine is running.
When the engine is cold, to prevent too great a distribution of cold
air, the air flow will reach its optimum level gradually.
In cold weather, it favours the distribution of warm air to the
windscreen, side windows and footwells only.
2. Driver's side adjustment
3. Passenger's side adjustment
The driver and front passenger can each adjust the
temperature to their requirements.
The value indicated on the display corresponds to a level
of comfort and not to a temperature in degrees Celsius or
Fahrenheit.
 Turn control 2 or 3 to the left or to the right respectively to decrease
or increase this value.
A setting around the value 21 provides optimum comfort. However,
depending on your requirements, a setting between 18 and 24 is
normal.
You are advised to avoid a left / right setting difference of more than 3.
AUTO
AUTOMATIC OPERATION
1. Automatic comfort programme
 Press the "AUTO" button. The indicator lamp in the
button comes on.
We recommend the use of this mode: it permits automatic and
optimised adjustment of all of the functions, passenger compartment
temperature, air flow, air distribution and air recirculation, in accordance
with the comfort value that you have chosen.
This system is designed to operate effectively in all seasons, with the
windows closed.
On entering the vehicle, if the interior temperature is much colder
or warmer than the comfort value, there is no need to change
the value displayed in order to obtain the comfort required. The
system corrects the difference in temperature automatically and
as quickly as possible.
3/ EASE OF USE and COMFORT
DUAL-ZONE DIGITAL
AIR CONDITIONING
4. Automatic visibility programme
5. Air conditioning On / Off
The automatic comfort programme may not be sufficient to
quickly demist or defrost the windscreen and side windows
(humidity, several passengers, ice, etc.).
 Press this button to activate the automatic visibility programme.
The indicator lamp in the button comes on.
The system automatically controls the air conditioning, the air flow and
the air intake and provides optimum distribution of the ventilation to the
windscreen and side windows.
 To switch the system off, press this button again or on "AUTO".
The indicator lamp in the button goes off and the indicator lamp in
the "AUTO" button comes on.
 Press this button to switch off the air conditioning.
Switching the system off could result in discomfort (humidity,
condensation).
 Press this button again to return to automatic operation of the air
conditioning. The indicator lamp in the "A/C" button comes on.
6. Air distribution adjustment
 Press one or more buttons to direct the air flow towards:
76
MANUAL OPERATION
If you wish, you can make a different choice from that offered by the
system by changing a setting. The other functions will still be controlled
automatically.
 Pressing the "AUTO" button returns the system to completely
automatic operation.
For maximum cooling or heating of the passenger compartment,
it is possible to exceed the minimum value 14 or the maximum
value 28.
 Turn control 2 or 3 to the left until "LO" is displayed or to the
right until "HI" is displayed.
-
the windscreen and side windows (demisting or defrosting),
the windscreen, the side windows and the vents,
the windscreen, the side windows, the vents and the footwells,
the vents and the footwells,
the vents,
the footwells,
the windscreen, the side windows and the footwells.
7. Air flow adjustment
 Turn this control to the left to decrease the air flow or to
the right to increase the air flow.
The air flow indicator lamps, between the two fans, come on
progressively in relation to the value requested.
 Press this button for recirculation of the interior air. The
indicator lamp in the button comes on.
Air recirculation enables the passenger compartment to be isolated
from exterior odours and smoke.
 As soon as possible, press this button again to permit the intake
of outside air and prevent the formation of condensation. The
indicator lamp on the button switches off.
9. Mono-zone / Dual-zone
 Press this button to equalise the comfort value on the
passenger's side with that on the driver's side (mono
zone). The indicator lamp in the button comes on.
SWITCHING THE SYSTEM OFF
 Turn the air flow control to the left until all of the indicator lamps
go off.
This action switches off the air conditioning and the ventilation.
Temperature related comfort is no longer guaranteed but a slight flow
of air, due to the movement of the vehicle, can still be felt.
 Turn the air flow dial to the right or press the "AUTO" button
to reactivate the system with the values set before it was
switched off.
Avoid prolonged operation in interior air recirculation mode or
driving for long periods with the system off (risk of condensation
and deterioration of the air quality).
REAR SCREEN DEMIST DEFROST
The control button is located on the heating or air conditioning
system control panel.
SWITCHING ON
The rear screen demisting/defrosting can only operate when the engine
is running.
 Press this button to demist/defrost the rear screen and (depending
on version) the door mirrors. The indicator lamp associated with
the button comes on.
SWITCHING OFF
The demisting/defrosting switches off automatically to prevent an
excessive consumption of current.
 It is possible to stop the demisting/defrosting operation before it
is switched off automatically by pressing the button again. The
indicator lamp associated with the button switches off.
If the engine is switched off before the demisting/defrosting is
switched off automatically, demisting/defrosting will resume next
time the engine is switched on.
 Switch off the demisting/defrosting of the rear screen and door
mirrors as soon as appropriate as lower current consumption
results in reduced fuel consumption.
3/ EASE OF USE and COMFORT
8. Air intake / Air recirculation
COURTESY LAMP
It switches off gradually:
when the vehicle is locked,
when the ignition is switched on,
30 seconds after the last door is closed.
Permanently off.
78
Permanent lighting.
A. Courtesy lamp
B. Map reading lamps
COURTESY LAMP
In this position, the courtesy lamp comes on gradually:
-
when the vehicle is unlocked,
when the key is removed from the ignition,
when a door is opened,
when the remote control locking button is activated, in order to
locate your vehicle.
With the "permanent lighting" mode, the duration of lighting varies,
depending on the circumstances:
with the ignition off, approximately ten minutes,
in energy economy mode, approximately thirty seconds,
with the engine running, unlimited.
MAP READING LAMPS
 With the ignition on, press the corresponding switch.
INTERIOR WELCOME LIGHTING
The dimmed passenger compartment lighting improves visibility in
the vehicle when the light is poor.
The remote switching on of the passenger compartment lighting
makes your entry into the vehicle easier in poor light. It is activated in
accordance with the light intensity detected by the brightness sensor.
SWITCHING ON
SWITCHING ON
At night, the footwell lighting and the front courtesy mood lamp come
on automatically when the sidelamps are switched on.
 Press the open padlock on the remote control.
The front door sill lighting, the footwell lighting and the courtesy lamps
come on; your vehicle is also unlocked.
SWITCHING OFF
SWITCHING OFF
The interior mood lighting switches off automatically when the
sidelamps are switched off.
The interior welcome lighting switches off automatically after a certain
time, when one of the doors is opened or the ignition is switched on.
PROGRAMMING
The function is activated or deactivated via the vehicle
configuration menu.
This function is activated by default.
3/ EASE OF USE and COMFORT
INTERIOR MOOD LIGHTING
EXTERIOR WELCOME LIGHTING
The remote switching on of the lighting makes your approach to the
vehicle easier in poor light. It is activated according to the level of light
detected by the sunshine sensor.
SWITCHING ON
 Press the open padlock on the remote control.
The dipped beam headlamps and the sidelamps come on; your
vehicle is also unlocked.
80
SWITCHING OFF
The exterior welcome lighting switches off automatically after a set time,
when the ignition is switched on or on locking the vehicle.
The duration of the welcome lighting is associated with and
identical to that of the automatic guide-me-home lighting.
INTERIOR FITTINGS
Sun visor
(see details on following page)
2. Central storage compartment (with
PEUGEOT Connect Sound (RD5))
3. Storage compartment
4. Illuminated and coolable glove box
(see details on following page)
5. Door pockets
6. Illuminated ashtray
(see details on following page)
7. Storage compartment with
non-slip mat
8. 12 V accessory socket
(see details on following page)
9. Cup holder
10. Adjustable front armrest
(see details on following page)
11. Open storage tray
3/ EASE OF USE and COMFORT
1.
SUN VISOR
82
Component which protects against sunlight from the front or the side,
also equipped with an illuminated courtesy mirror.
 With the ignition on, raise the concealing flap; the mirror is lit
automatically.
This sun visor is also equipped with a ticket holder.
ILLUMINATED AND COOLABLE
GLOBE BOX
This has areas for storing a bottle of water, the vehicle's handbook
pack...
Its lid has areas for storing a pen, a pair of spectacles, tokens, cards,
a can...
 To open the glove box, raise the handle.
The lamp comes on when the lid is opened.
The glove box is equipped with an air vent, which can be opened or
closed. This distributes the same conditioned air as the vents in the
passenger compartment.
ILLUMINATED ASHTRAY
 To connect a 12 V accessory (max power: 120 W), lift the cover
and connect a suitable adaptor.
 Pull the drawer for access to the ashtray.
 To empty the ashtray, after opening, press the tab and remove
the ashtray.
3/ EASE OF USE and COMFORT
12 V ACCESSORY SOCKET
FRONT ARMREST
LONGITUDINAL ADJUSTMENT
Comfort and storage device for the driver and front passenger.
The height and length of the armrest cover can be adjusted.
HEIGHT ADJUSTMENT
 Slide the cover fully forwards or rearwards.
84
STORAGE
 Raise the cover to the required position (low, intermediate or high).
 If you raise the cover slightly beyond the high position, guide it
when lowering it to the low position.
 Raise the lever.
 Raise the cover fully.
USB PLAYER
This connection box, consisting of a USB port, is located in the front
armrest.
It permits the connection of portable equipment, such as an iPod®
digital audio player of generation 5 or later or a USB memory stick.
It reads the audio file formats (mp3, ogg, wma, wav...) which are
transmitted to your audio equipment and played via the vehicle's
speakers.
You can manage these files using the steering mounted controls or the
audio equipment control panel and display them in the multifunction
screen.
This connection box, consisting of a JACK socket and a USB port,
is located in the front armrest.
With the USB port, it permits the connection of portable equipment,
such as a digital audio player of the iPod® or USB memory stick type.
With the JACK socket, it permits the connection of any type of portable
player.
It reads the audio file formats (mp3, ogg, wma, wav...) which are
transmitted to your audio equipment and played via the vehicle's
speakers.
If the equipment is connected to the USB port, you can manage these
files using the steering mounted controls or the audio equipment control
panel and display them in the multifunction screen.
If the equipment is connected to the USB port, when it is in use,
the portable equipment charges automatically.
For more information on the use of this equipment, refer to
the PEUGEOT Connect Sound (RD5) or PEUGEOT Connect
Navigation (RT6) section.
When it is in use, the portable equipment charges automatically.
For more information on the use of this equipment, refer to the
corresponding audio section.
3/ EASE OF USE and COMFORT
PEUGEOT CONNECT USB
MATS
Removable carpet protection.
REFITTING
To refit the mat on the driver's side:
 position the mat correctly,
 refit the fixings by pressing,
 check that the mat is secured correctly.
86
To avoid any risk of jamming of the pedals:
only use mats which are suited to the fixings already present
in the vehicle; these fixings must be used,
never fit one mat on top of another.
The use of mats not approved by PEUGEOT may interfere
with access to the pedals and hinder the operation of the cruise
control / speed limiter.
FITTING
When fitting the mat for the first time, on the driver's side use only the
fixings provided in the wallet attached.
The other mats are simply placed on the carpet.
REMOVAL
To remove the mat on the driver's side:
 move the seat as far back as possible,
 unclip the fixings,
 remove the mat.
BOOT FITTINGS
Stowing rings
Storage net
Storage box
(see details on following page)
3/ EASE OF USE and COMFORT
1.
2.
3.
BOOT LAMPS
This has areas for storing a box of spare bulbs, a first aid kit, the
temporary puncture repair kit, a warning triangle, the removable ball
of the towbar system...
Your vehicle is fitted with two boot lamps; one in the right-hand boot
side trim and a second in the centre under the rear shelf.
They come on automatically when the boot is opened and switch off
automatically when the boot is closed.
They cannot be deactivated manually.
88
STORAGE BOX
The duration of lighting varies, depending on the context:
when the ignition is off, approximately ten minutes,
in energy economy mode, approximately thirty seconds,
when the engine is running, no limit.
For access to it:
 raise the floor using the strap,
 secure it in the vertical position behind the stops, located on
the sides of the boot.
A second warning triangle can be stored in the boot lid trim.
EXTERIOR LIGHTING CONTROLS
Control stalk for the selection and control of the various front and rear
lamps providing the vehicle's lighting.
MAIN LIGHTING
SETTINGS
The various front and rear lamps of the vehicle are designed to adapt
the driver's visibility progressively in relation to the climatic conditions:
sidelamps, to be seen,
dipped beam headlamps to see without dazzling other drivers,
main beam headlamps to see clearly when the road is clear.
Various automatic lighting control modes are also available depending
on options:
daytime running lamps,
automatic illumination of headlamps,
directional lighting,
guide-me-home lighting.
Other lamps are fitted to fulfil the requirements of particular driving
conditions:
a rear foglamp to be seen from a distance,
directional headlamps for improved visibility when cornering,
daytime running lamps to be seen during the day.
In some weather conditions (e.g. low temperature or humidity),
the presence of misting on the internal surface of the glass of the
headlamps and rear lamps is normal; it disappears after the lamps
have been on for a few minutes.
4/ VISIBILITY
ADDITIONAL LIGHTING
MANUAL CONTROLS
Model without AUTO lighting
The lighting is controlled directly by the driver by means of the ring A
and the stalk B.
A. Main lighting mode selection ring: turn it to position the symbol
required facing the mark.
Lighting off / daytime running lamps.
Automatic illumination of headlamps.
90
Sidelamps only.
Model with AUTO lighting
Dipped or main beam headlamps.
B. Stalk for switching headlamps: pull it to switch between dipped
headlamps / main beam headlamps.
In the lamps off and sidelamps modes, the driver can switch on the
main beam headlamps temporarily ("headlamp flash") by maintaining a
pull on the stalk.
DISPLAYS
Lighting of the corresponding indicator lamp on the instrument panel
confirms the switching on of the lighting selected.
The instrument panel has permanent back-lighting, both day and night.
In this case, illumination of the instrument panel is not linked to the
exterior lighting.
Rear foglamp.
 Turn the ring C forwards and release to switch on the rear foglamp.
When the lighting is switched off automatically (with AUTO model)
or when the dipped beam headlamps are switched off manually, the
foglamp and the sidelamps will remain on.
 Turn the ring C rearwards and release to switch off all the lamps.
In good or rainy weather, both day and night, use of the rear
foglamp is prohibited. In these situations, the power of its beam
may dazzle other drivers. It should only be used in fog or snow.
In these weather conditions, it is your responsibility to switch
on the foglamp and dipped beam headlamps manually as the
sunshine sensor may detect sufficient light.
Do not forget to switch off the rear foglamp when it is no longer
needed.
Switching off the lamps when the ignition is switched off
On switching off the ignition, all of the lamps turn off immediately,
except for dipped beam if guide-me-home lighting is activated.
Switching on the lamps after the ignition is switched off
To reactivate the lighting control, rotate ring A to the "0" position lamps off, then to the desired position.
On opening the driver's door a temporary audible signal warns the
driver that the lighting is on.
The lamps, with the exception of the sidelamps, switch off
automatically after a maximum duration of thirty minutes to
prevent discharging of the battery.
4/ VISIBILITY
C. Foglamp selection ring.
The foglamp operates with the dipped and main beam headlamps.
LED LAMPS
DAYTIME RUNNING LAMPS
Daytime lighting, compulsory in certain countries, which comes on
automatically when the engine is started providing better visibility of the
vehicle by other road users.
92
In countries in which it is imposed by regulations:
by default, this function is activated and cannot be deactivated,
the dipped beam headlamps come on, associated with the
sidelamps and the number plate lamps.
They come on when the engine is started.
Depending on the destination country, they are used for:
daytime running lamps* in day mode and sidelamps in night mode
(they are brighter when daytime running lamps),
or
sidelamps in day and night mode.
Where LED lamps are fitted, the filament bulbs for the daytime running
lamps / sidelamps in the front lamp units are not used.
* function that can be set in the vehicle configuration menu.
For other countries where the vehicle is sold, this function is assured
by specific lamps. The lighting control stalk should be in position "0"
or "AUTO".
This function can be activated or deactivated via the vehicle
configuration menu.
Deactivation of the daytime running lamps is effective after
operation of the lighting control stalk or after the next engine
start; activation is immediate.
MANUAL GUIDE-ME-HOME LIGHTING
AUTOMATIC ILLUMINATION OF HEADLAMPS
The temporary illumination of the dipped beam headlamps after the
vehicle's ignition has been switched off makes the driver's exit easier
when the light is poor.
When a low level of ambient light is detected by a sunshine sensor, the
number plate lamps, sidelamps and dipped beam headlamps are switched
on automatically, without any action on the part of the driver. They can also
come on if rain is detected, at the same time as automatic operation of the
windscreen wipers.
As soon as the brightness returns to a sufficient level or after the windscreen
wipers are switched off, the lamps are switched off automatically.
Switching on
Switching off
The manual guide-me-home lighting switches off automatically after a
set time.
Activation
 Turn the ring to the "AUTO" position. The activation of the function
is accompanied by the display of a message in the screen.
Deactivation
 Turn the ring to another position. Deactivation of the function is
accompanied by the display of a message in the screen.
4/ VISIBILITY
 With the ignition off, "flash" the headlamps using the lighting stalk.
 A further "headlamp flash" switches the function off.
Operating fault
AUTOMATIC "GUIDE-ME-HOME" LIGHTING
In the event of a malfunction of the sunshine sensor, the
lighting comes on, this warning lamp is displayed in the
instrument panel and/or a message appears in the screen,
accompanied by an audible signal.
Contact a PEUGEOT dealer or a qualified workshop.
When the automatic illumination of headlamps function is activated
(lighting control stalk in the "AUTO" position), under low ambient light
the dipped beams headlamps come on automatically when the ignition
is switched off.
94
In fog or snow, the sunshine sensor may detect sufficient light. In
this case, the lighting will not come on automatically.
Do not cover the sunshine sensor, coupled with the rain sensor
and located in the centre of the windscreen behind the rear view
mirror; the associated functions would no longer be controlled.
Programming
Activation or deactivation, as well as the duration of the guide-me-home
lighting, is set in the vehicle configuration menu.
MANUAL ADJUSTMENT OF
HALOGEN HEADLAMPS
AUTOMATIC ADJUSTMENT OF
XENON HEADLAMPS
In order to avoid causing a nuisance to other road users, this system
corrects the height of the xenon headlamp beams automatically and
when stationary, in relation to the load in the vehicle.
If a malfunction occurs, this warning lamp is displayed on the
instrument panel, accompanied by an audible signal and a
message in the screen.
The system then places your headlamps in the lowest position.
Initial setting is position "0".
Do not touch the xenon headlamp bulbs.
Contact a PEUGEOT dealer or a qualified workshop.
Travelling abroad
If using your vehicle in a country that drives on the other side of
the road, the headlamps must be adjusted to avoid dazzling oncoming drivers.
Contact a PEUGEOT dealer or a qualified workshop.
4/ VISIBILITY
To avoid dazzling other road users, the height of the halogen bulb
headlamps must be adjusted according to the load in the vehicle.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 4 people.
-. Intermediate setting.
2. 4 people + maximum authorised loads.
-. Intermediate setting.
3. Driver + maximum authorised loads.
DIRECTIONAL LIGHTING
When the dipped or main beam headlamps are on, this function enables
the light beams to provide improved lighting of the side of the road when
cornering.
The use of this function, from approximately 12 mph (20 km/h) and
associated with the xenon headlamps only, considerably improves the
quality of your lighting when cornering.
with directional lighting
PROGRAMMING
The function is activated or deactivated via the vehicle
configuration menu.
OPERATING FAULT
96
If a fault occurs, this warning lamp flashes in the instrument
panel, accompanied by a message in the screen.
Contact a PEUGEOT dealer or a qualified workshop.
When stationary or moving at very low speed or when reverse
gear is engaged, the function is inactive.
The status of the function remains in the memory when the
ignition is switched off.
without directional lighting
WIPER CONTROLS
Control stalk for the various windscreen wiping modes for clearing rain
and cleaning the windscreen.
Model with AUTO wiping
PROGRAMMING
An automatic mode is also available, providing automatic rain sensitive
windscreen wipers.
MANUAL OPERATION OF THE WINDSCREEN
WIPERS
This control stalk allows selection of the most suitable wiping speed
according to the weather conditions.
Fast (heavy rain).
Intermittent (proportional to the speed of the vehicle).
Park.
automatic, then single wipe (see the corresponding
section).
4/ VISIBILITY
Normal (moderate rain).
WINDSCREEN AND HEADLAMP WASH
Screenwash/headlamp wash low
98
In the case of vehicles fitted with headlamp washers, when
the minimum level of the reservoir is reached, this warning
lamp and/or the service warning lamp is displayed in the
instrument panel, accompanied by an audible signal and a
message in the screen.
Next time you stop, fill the screenwash / headlamp wash fluid reservoir.
The warning lamp is displayed when the ignition is switched on, or
every time the stalk is operated, until the reservoir is filled.
 Pull the windscreen wiper stalk towards you. The windscreen wash
then the windscreen wipers operate for a fixed period.
The headlamp washers only operate when the dipped or main beam
headlamps are on, with the vehicle moving.
To reduce the consumption of the fluid by the headlamp washers,
they operate only with every seventh use of the screenwash or
every 25 miles (40 km) during a given journey.
AUTOMATIC RAIN SENSITIVE WINDSCREEN
WIPERS
The windscreen wipers operate automatically, without any action on the
part of the driver, if rain is detected (sensor behind the rear view mirror),
adapting their speed to the intensity of the rainfall.
The automatic rain sensitive wipers must be reactivated if the
ignition has been off for more than one minute, by pushing the
stalk downwards.
Operating fault
If an automatic wiping malfunction occurs, the wipers will operate in
intermittent mode.
Have it checked by a PEUGEOT dealer or a qualified workshop.
This is controlled manually by the driver by pushing the stalk
downwards to the "AUTO" position.
It is accompanied by a message in the screen.
Switching off
This is controlled manually by the driver by moving the stalk upwards
then returning it to position "0".
It is accompanied by a message in the screen.
Do not cover the rain sensor, linked with the sunshine sensor
and located in the centre of the windscreen behind the rear view
mirror.
Switch off the automatic rain sensitive wipers when using an
automatic car wash.
In winter, to avoid damaging the wiper blades, it is advisable
to wait until the windscreen is completely clear of ice before
activating the automatic rain sensitive wipers.
4/ VISIBILITY
Activation
100
SPECIAL POSITION OF THE WINDSCREEN
WIPERS
This position permits release of the windscreen wiper blades.
It is used for cleaning or replacement of the blades. It can also be
useful, in winter, to detach the blades from the windscreen.
 Any action on the wiper stalk in the minute after switching off the
ignition places the blades vertically on the screen.
 To park the blades again, switch on the ignition and operate the
wiper stalk.
To maintain the effectiveness of the "flat-blade" type of wiper
blades, it is advisable to:
handle them with care,
clean them regularly using soapy water,
avoid using them to retain cardboard on the windscreen,
replace them at the first signs of wear.
DIRECTION INDICATORS
HAZARD WARNING LAMPS
A visual warning by means of the direction indicators to alert other road
users to a vehicle breakdown, towing or accident.
If you forget to cancel the direction indicators for more than
twenty seconds, the volume of the audible signal will increase if
the speed is above 40 mph (60 km/h).
 Press this button, the direction indicators flash.
They can operate with the ignition off.
AUTOMATIC OPERATION OF HAZARD
WARNING LAMPS*
When braking in an emergency, depending on the deceleration, the
hazard warning lamps come on automatically.
They switch off automatically the first time you accelerate.
 You can also switch them off by pressing the button.
Deactivating the DSC/ASR systems also deactivates the automatic
operation of the hazard warning lamps; refer to the "Trajectory control
systems - Deactivation" section.
* Except for the 1.6 litre THP 270 hp version.
5/ SAFETY
 Left: lower the lighting stalk passing the point of resistance.
 Right: raise the lighting stalk passing the point of resistance.
EMERGENCY OR ASSISTANCE
CALL
HORN
Audible warning to alert other road users to an imminent danger.
102
This system allows you to make an emergency or assistance call to the
emergency services or to the dedicated PEUGEOT service.
For more information on the use of this function, refer to the "Audio
equipment and telematics" section.
 Press one of the spokes of the steering wheel.
Use the horn with moderation, observing the driving regulations of the
country you are driving in.
BRAKING ASSISTANCE SYSTEMS
Group of supplementary systems which help you to obtain optimum
braking in complete safety in emergency situations:
anti-lock braking system (ABS),
electronic brake force distribution (EBFD),
emergency braking assistance (EBA).
ANTI-LOCK BRAKING SYSTEM AND
ELECTRONIC BRAKE FORCE DISTRIBUTION
If this warning lamp comes on, together with the STOP and
ABS warning lamps, accompanied by an audible signal and
a message in the screen, it indicates a malfunction of the
electronic brake force distribution which could result in loss of control of
the vehicle when braking.
You must stop as soon as it is safe to do so.
In either case, contact a PEUGEOT dealer or a qualified workshop.
When replacing wheels (tyres and rims), ensure that they conform
to the manufacturer's recommendations.
Linked systems which improve the stability and manoeuvrability of your
vehicle when braking, in particular on poor or slippery surfaces.
Activation
EMERGENCY BRAKING ASSISTANCE
The anti-lock braking system comes into operation automatically when
there is a risk of wheel lock.
Normal operation of the ABS may make itself felt by slight vibration of
the brake pedal.
System which, in an emergency, enables you to obtain the optimum
braking pressure more quickly, thus reducing the stopping distance.
It is triggered by the speed at which the brake pedal is pressed.
The effect of this is a reduction in the resistance of the pedal and an
increase in braking efficiency.
Operating fault
If this warning lamp comes on, accompanied by an audible
signal and a message in the screen, it indicates a malfunction
of the anti-lock braking system which could result in loss of
control of the vehicle when braking.
When braking in an emergency, press firmly without releasing the
pressure.
5/ SAFETY
When braking in an emergency, press very firmly without releasing
the pressure.
Activation
TRAJECTORY CONTROL SYSTEMS
DYNAMIC STABILITY CONTROL (DSC) AND
ANTI-SLIP REGULATION (ASR)
104
The anti-slip regulation (also known as traction control) optimises
traction to prevent skidding of the wheels, by acting on the brakes of the
driving wheels and on the engine.
The electronic stability control acts on the brake of one or more wheels
and on the engine to keep the vehicle on the trajectory required by the
driver, within the limits of the laws of physics.
SNOW DRIVING ASSISTANCE
(INTELLIGENT TRACTION CONTROL)
Your vehicle has a system to help driving on snow: Intelligent Traction
Control.
This automatic system continuously checks for situations of difficult
surface adhesion that could make it difficult to move off or make
progress on deep fresh snow or compacted snow.
In these situations, Intelligent Traction Control limits the amount of
wheel slip to provide the best traction and trajectory control.
In extremely severe conditions (deep snow, mud…), it can be useful to
temporarily deactivate the dynamic stability control and wheel antislip systems to allow a degree of wheel spin and so recover grip.
It is recommended that the system be reactivated as soon as possible.
Snow tyres are strongly recommended on surfaces offering low levels
of adhesion.
Activation
These systems are activated automatically each time the vehicle is
started.
These systems act on the operation of the engine and brakes as soon
as they detect a problem of grip or trajectory.
This is indicated by flashing of this warning lamp in the
instrument panel.
Deactivation
In exceptional conditions (starting a vehicle which is bogged down,
stuck in snow, on soft ground...), it may be advisable to deactivate the
DSC and ASR, so that the wheels can turn freely and regain grip.
Reactivate the systems as soon as the level of grip permits.
Operating fault
Illumination of this warning lamp and the lamp in the
deactivation button, accompanied by an audible signal and a
message, indicate a fault with the system.
Contact a PEUGEOT dealer or a qualified workshop to have the system
checked.
DSC/ASR
The indicator lamp in the button comes on.
The DSC and ASR systems no longer act on the operation of the engine
and on the brakes in the event of a involuntary change of trajectory.
This action also deactivates the automatic operation of hazard warning
lamps (except for the 1.6 litre THP 270 hp version).
Reactivation
The systems are reactivated automatically each time the ignition is
switched back on.
You can also reactivate them manually:
 Press this button again.
This action also reactivates the automatic operation of hazard warning
lamps (except for the 1.6 litre THP 270 hp version).
After an impact, have these systems checked by a PEUGEOT
dealer or a qualified workshop.
5/ SAFETY
 Press this button.
The DSC and ASR systems offer increased safety in normal
driving, but they should not encourage the driver to take extra
risks or drive at high speed.
It is in difficult driving conditions (rain, snow, ice) that the risk of
loss of grip increases. It is therefore important for your safety to
keep the DSC and ASR systems activated in all conditions, and
particularly in difficult conditions.
The correct operation of these systems depends on observation
of the manufacturer's recommendations regarding as much the
wheels (tyres and rims), braking and electronic components as the
assembly and repair procedures used by PEUGEOT dealers.
To benefit in full from the effectiveness of the DSC and ASR
systems in wintry conditions, the vehicle must be fitted with four
snow tyres, allowing the the vehicle to retain neutral behaviour on
the road.
ACTIVE BONNET
The active bonnet has been designed to maximise the safety of
pedestrians in the event of an impact with the front of the vehicle.
This equipment can only operate once. If a second impact occurs
(during the same or a subsequent accident), the active bonnet will
not operate.
After an accident or theft of the vehicle, have the system checked.
Do not handle the pyrotechnic systems, located under the bonnet
near the struts: risk of explosion.
All work on this system is strictly prohibited unless carried out by
skilled personnel of a PEUGEOT dealer or a qualified workshop.
106
Operating fault
If this warning lamp comes on on the instrument panel,
accompanied by an audible signal and a message in the
screen, contact a PEUGEOT dealer or a qualified workshop to
have the system checked. The active bonnet may no longer
be deployed in the event of an impact.
The deployment of the active bonnet is accompanied by a slight
emission of harmless smoke and a noise, due to the activation
of the pyrotechnic cartridge integrated in the system. The airbag
warning lamp comes on.
After deployment, close the bonnet by pressing on the hinges.
Go to the nearest PEUGEOT dealer or a qualified workshop at a
maximum speed of 20 mph (30 km/h).
System which improves the aerodynamics and stability of the vehicle
when driving. It can be controlled automatically or manually.
Except 1.6 litre THP 270 hp version.
OPERATION
The use of the vehicle must comply with the legislation in force
in your country. This system can be used to its full potential on a
closed circuit.
Automatic mode
The spoiler rises automatically according to the speed and has two
positions.
When the speed of the vehicle is higher than 50 mph (85 km/h),
the spoiler rises automatically to the intermediate position A.
It remains in this position for as long as the speed remains above
35 mph (55 km/h).
If the speed of the vehicle falls below 35 mph (55 km/h), the spoiler
retracts automatically.
When the speed of the vehicle is higher than 95 mph (155 km/h),
the spoiler rises automatically to the maximum position B. It remains
in this position for as long as the speed remains above 90 mph
(142 km/h).
If the speed of the vehicle falls below 90 mph (142 km/h),
the spoiler retracts automatically to the intermediate position.
In this mode, the indicator lamp in the control button is off.
Manual mode
To control the operation of the spoiler manually, with the ignition on:
 press the control button briefly, the spoiler rises to the maximum
position B.
In this mode, the indicator lamp on the control button is on.
When stationary or moving at less than 6 mph (10 km/h), press and
hold the button until the indicator lamp goes off, the spoiler then retracts
completely.
5/ SAFETY
ACTIVE SPOILER
Before operating the spoiler, ensure that no one is in the proximity
of the moving parts to avoid any risk of injury.
Nevertheless, in the event of pinching, you must reverse the
movement of the spoiler. To do this, release the control button
then press it again to raise the spoiler.
To exit from manual mode:
 press the button briefly: the indicator lamp on the button goes off
(return to automatic mode).
108
At speeds below 6 mph (10 km/h), the spoiler stays in the open
position. It retracts automatically as soon as the vehicle exceeds
this speed threshold.
MAINTENANCE
To maintain the spoiler, with the vehicle stationary, ignition on:
 raise the spoiler to the maximum position B by pressing the
button briefly,
 once the cleaning is complete, retract the spoiler: press and hold
the button until the end of the manoeuvre.
The keep this system in good working order, check the spoiler and its
housing periodically preventing the unwanted accumulation of leaves,
ice or snow.
Before washing the vehicle, always retract the spoiler into its
housing.
Keep the end of the high-pressure nozzle at least 1 metre from the
spoiler housing.
OPERATING FAULT
If the control system fails, the indicator lamp in the control button
flashes, accompanied by an audible signal and a message in the
screen. As a safety precaution, the spoiler rises to the maximum
position, regardless of the speed of the vehicle.
If the problem persists and you wish to retract the spoiler:
 stop where it is safe to do so,
 switch off the ignition,
 switch the ignition on again.
If the indicator lamp no longer flashes, the failure was temporary, the
system has resumed normal operation. To retract the spoiler, refer to
the paragraph "To exit from manual mode".
If the indicator lamp flashes again and the spoiler is still raised, the
system is still faulty.
Have it checked by a PEUGEOT dealer or a qualified workshop.
In the event of a system operating fault (e.g. jamming of the spoiler), the
indicator lamp in the control button flashes, accompanied by an audible
signal and a message in the screen. For safety reasons, do not exceed
a speed of 85 mph (140 km/h).
Have it checked by a PEUGEOT dealer or a qualified workshop.
Never press on the spoiler to close the boot or push the vehicle as
this may damage it.
The installation of load-carrying accessories on the vehicle limits
the effectiveness of the spoiler.
Do not install load carrying accessories which are not
recommended by PEUGEOT.
FIXED SPOILER
1.6 litre THP 270 hp version only.
When pushing the vehicle, do not press on the spoiler as there is
a risk of damaging it.
The installation of carrying accessories on the vehicles reduces
the effectiveness of the spoiler.
Only install carrying accessories that are recommended by
PEUGEOT.
5/ SAFETY
When washing your vehicle with a high pressure jet-wash, keep
the end of the lance at least 1 metre away from the spoiler.
SEAT BELTS
Seat belt not fastened / unfastened warning lamps display
FRONT SEAT BELTS
The front seat belts are fitted with a pretensioning and force limiting
system.
This system improves safety in the front seats in the event of a front or
side impact. Depending on the severity of the impact, the pretensioning
system instantly tightens the seat belts against the body of the
occupants.
The pretensioning seat belts are active when the ignition is on.
The force limiter reduces the pressure of the seat belt on the chest of
the occupant, so improving their protection.
110
Fastening
 Pull the strap, then insert the tongue in the buckle.
 Check that the seat belt is fastened correctly by pulling the strap.
Unfastening
 Press the red button on the buckle.
 Guide the seat belt as it reels in.
A. Front seat belts not fastened / unfastened warning lamp.
B. Front left seat belt warning lamp.
C. Front right seat belt warning lamp.
When the ignition is switched on, the warning lamp A comes on in the
seat belt and passenger's front airbag warning lamp display, if the driver
and/or the front passenger has not fastened their seat belt.
From approximately 12 mph (20 km/h) this warning lamp flashes for
two minutes accompanied by an audible signal of increasing volume.
Once these two minutes have elapsed, this warning lamp remains on
until the driver and/or the front passenger fastens their seat belt.
The warning lamp B or C for the corresponding seat comes on in red if
the seat belt is not fastened or is unfastened.
REAR SEAT BELTS
Seat belt unfastened warning lamps display
The rear seats are each fitted with a three-point inertia reel seat belt
with force limiter.
1.
2.
3.
Pull the strap and insert the tongue F in the black buckle F, in the
centre of the bench seat.
Insert the tongue G in the outer red buckle G.
Check that each buckle is fastened correctly by pulling the strap.
A. Rear seat belts unfastened warning lamp.
D. Rear right seat belt warning lamp.
E. Rear left seat belt warning lamp.
The warning lamp A comes on, either on in the seat belt and
passenger's front airbag warning lamps display, when one or more rear
passengers unfasten their seat belt.
From approximately 12 mph (20 km/h), this warning lamp flashes for
two minutes accompanied by an audible signal of increasing volume.
Once these two minutes have elapsed, this warning lamp remains on
until the one or more rear passengers fasten their seat belt.
When the ignition is switched on, with the engine running or the vehicle
moving at a speed below approximately 12 mph (20 km/h),
the corresponding warning lamps D and E come on in red for
approximately 30 seconds, if the seat belt is not fastened.
When the vehicle is moving at a speed of more than approximately
12 mph (20 km/h), the corresponding warning lamp D or E comes on in
red, accompanied by an audible signal and a message in the screen,
if a rear passenger has unfastened their seat belt.
Unfastening
1.
2.
Press the red button on the buckle G, then the black button on the
buckle F.
Guide the strap as it reels in and bring the tongue G, then the
tongue F to the corresponding securing point on the backrest.
Unfastening is detected on both buckles of the seat belt. The
corresponding warning lamp comes on when at least one of the
two buckles is unfastened.
5/ SAFETY
Fastening
112
The driver must ensure that passengers use the seat belts
correctly and that they are all restrained securely before
setting off.
Wherever you are seated in the vehicle, always fasten your seat
belt, even for short journeys.
Do not interchange the seat belt buckles as they will not fulfil their
role fully.
The seat belts are fitted with an inertia reel permitting automatic
adjustment of the length of the strap to your size. The seat belt is
stowed automatically when not in use.
Before and after use, ensure that the seat belt is reeled in
correctly.
The lower part of the strap must be positioned as low as possible
on the pelvis.
The upper part must be positioned in the hollow of the shoulder.
The inertia reels are fitted with an automatic locking device which
comes into operation in the event of a collision, emergency
braking or if the vehicle rolls over. You can release the device by
pulling firmly on the strap and releasing it so that it reels in slightly.
In order to be effective, a seat belt must:
be tightened as close to the body as possible,
be pulled in front of you with a smooth movement, checking
that it does not twist,
be used to restrain only one person,
not bear any trace of cuts or fraying,
not be converted or modified to avoid affecting its
performance.
In accordance with current safety regulations, for all repairs on your
vehicle, go to a qualified workshop with the skills and equipment
needed, which a PEUGEOT dealer is able to provide.
Have your seat belts checked regularly by a PEUGEOT dealer or a
qualified workshop, particularly if the straps show signs of damage.
Clean the seat belt straps with soapy water or a textile cleaning
product, sold by PEUGEOT dealers.
After folding or moving a seat or rear bench seat, ensure that the
seat belt is positioned and reeled in correctly.
Recommendations for children
Use a suitable child seat if the passenger is less than 12 years old or
shorter than one and a half metres.
Never use the same seat belt to secure more than one person.
Never allow a child to travel on your lap.
In the event of an impact
Depending on the nature and seriousness of the impact, the
pretensioning device may be deployed before and independently
of the airbags. Deployment of the pretensioners is accompanied
by a slight discharge of harmless smoke and a noise, due to the
activation of the pyrotechnic cartridge incorporated in the system.
In all cases, the airbag warning lamp comes on.
Following an impact, have the seat belts system checked, and if
necessary replaced, by a PEUGEOT dealer or a qualified workshop.
The airbags have been designed to maximise the safety of the
occupants in the event of violent collisions. They supplement the action
of the force-limiting seat belts.
In this case, the electronic detectors record and analyse the front and
side impacts suffered in the impact detection zones:
in the event of a serious impact, the airbags are deployed
instantaneously and contribute towards protecting the occupants of
the vehicle; immediately after the impact, the airbags deflate rapidly
so that they do not hinder the visibility of the occupants or their
possible exit from the vehicle,
in the event of a minor impact or rear impact and in certain roll-over
conditions, the airbags will not be deployed; the seat belt alone
contributes towards providing your protection in these situations.
The airbags do not operate when the ignition is off.
This equipment only operates once. If a second impact occurs
(during the same or a subsequent accident), the airbag will not
operate.
Impact detection zones
A. Front impact zone.
B. Side impact zone.
The deployment of one or more airbags is accompanied by a
slight discharge of smoke and a noise, due to the activation of the
pyrotechnic cartridge incorporated in the system.
This smoke is not harmful, but sensitive individuals may
experience some irritation.
The noise of the detonation may result in a slight loss of hearing
for a short time.
5/ SAFETY
AIRBAGS
Deactivation
System which protects the driver and front passenger in the event of
a serious front impact in order to limit the risk of injury to the head and
chest.
The driver's airbag is fitted in the centre of the steering wheel; the front
passenger's airbag is fitted in the dashboard above the glove box.
Only the passenger's front airbag can be deactivated:
 with the ignition off, insert the key in the passenger airbag
deactivation switch,
 turn it to the "OFF" position,
 then, remove the key keeping the switch in the new position.
114
FRONT AIRBAGS
Deployment
The airbags are deployed, except the passenger's front airbag if it is
deactivated, in the event of a serious front impact to all or part of the
front impact zone A, in the longitudinal centreline of the vehicle on a
horizontal plane and directed from the front to the rear of the vehicle.
The front airbag inflates between the chest and head of the front
occupant of the vehicle and the steering wheel, driver's side, and the
dashboard, passenger's side to cushion their forward movement.
This warning lamp comes on in the passenger's front airbag
warning lamps display when the ignition is on and until the
airbag is reactivated.
To assure the safety of your child, the passenger's front airbag
must be deactivated when you install a "rearward facing" child
seat on the front passenger seat.
Otherwise, the child would risk being seriously injured or killed if
the airbag were deployed.
Reactivation
LATERAL AIRBAGS
When you remove the child seat, turn the switch to the "ON" position to
reactivate the airbag and so assure the safety of your front passenger in
the event of an impact.
System which protects the driver and front passenger in the event of a
violent side impact in order to limit the risks of injury to the pelvis, chest
and head*.
The lateral airbags are installed on the outer side of the seat:
one part in the front seat frame (chest-pelvis airbag),
one part in the front head restraint* (head airbag).
With the ignition on, this warning lamp comes on in the seat
belt and passenger's front airbag warning lamps display for
approximately one minute, if the passenger's front airbag is
activated.
Operating fault
If this warning lamp comes on in the instrument panel,
accompanied by an audible warning and a message in the
screen, contact a PEUGEOT dealer or a qualified workshop
to have the system checked. The airbags may no longer be
deployed in the event of a serious impact.
It is deployed unilaterally in the event of a violent impact applied to
all or part of the side impact zone B, operating at right angles to the
longitudinal axis of the vehicle in a horizontal plane and from the
exterior of the vehicle towards the interior.
The lateral airbag comes between the front occupant of the vehicle and
the corresponding door trim panel.
* Except for the 1.6 litre THP 270 hp version.
5/ SAFETY
Deployment
The airbag may not be deployed in an impact or minor accident on
the side of the vehicle.
The airbag is not deployed in a front or rear impact.
Operating fault
116
Impact detection zones
A. Front impact zone.
B. Side impact zone.
If this warning lamp comes on on the instrument panel,
accompanied by an audible signal and a message in the
screen, contact a PEUGEOT dealer or a qualified workshop
to have the system checked. The airbags may no longer be
deployed in the event of a violent impact.
Sit in a normal upright position.
Wear a correctly adjusted seat belt.
Do not leave anything between the occupants and the airbags
(a child, pet, object...). This could hamper the operation of the
airbags or injure the occupants.
After an accident or if the vehicle has been stolen or broken into,
have the airbag systems checked.
All work on the airbag system must be carried out by a PEUGEOT
dealer or a qualified workshop.
Even if all of the precautions mentioned are observed, a risk of
injury or of minor burns to the head, chest or arms when an airbag
is deployed cannot be ruled out. The bag inflates almost instantly
(within a few milliseconds) then deflates within the same time
discharging the hot gas via openings provided for this purpose.
Front airbags
Do not drive holding the steering wheel by its spokes or resting your
hands on the centre part of the wheel.
Passengers must not place their feet on the dashboard.
If possible, do not smoke as deployment of the airbags can cause
burns or the risk of injury from a cigarette or pipe.
Never remove or pierce the steering wheel or hit it violently.
Lateral airbags
Do not fix or attach anything to the seat backs. This could cause
injury to the chest or arms if the lateral airbag is triggered.
Do not sit with the upper part of the body any nearer to the door than
necessary.
5/ SAFETY
For the airbags to be fully effective, observe the following
safety rules:
GENERAL POINTS RELATING TO
CHILD SEATS
Although one of PEUGEOT main criteria when designing your vehicle,
the safety of your children also depends on you.
Only children between 9 and 18 kg can be carried on the rear
seats in a forward facing universal ISOFIX child seat.
118
For maximum safety, please observe the following recommendations:
in accordance with European regulations, all children under the
age of 12 or less than one and a half metres tall must travel in
approved child seats suited to their weight, on seats fitted with a
seat belt or ISOFIX mountings*,
statistically, the safest seats in your vehicle for carrying
children are the rear seats,
a child weighing less than 9 kg must travel in the "rearward
facing" position both in the front and in the rear.
CHILD SEAT AT THE REAR
PEUGEOT recommends that children should travel in the outer
rear seats of your vehicle:
"rearward facing" up to the age of 3,
"forward facing" over the age of 3.
* The rules for carrying children are specific to each country. Refer to
the legislation in force in your country.
"REARWARD-FACING"
When a "rearward-facing" child seat is installed on the front passenger
seat, adjust the seat to the intermediate longitudinal and highest
position, with the backrest straightened.
The passenger airbag must be deactivated. Otherwise, the child would
risk being seriously injured or killed if the airbag were to inflate.
Ensure that the seat belt is correctly tensioned.
For child seats with a support leg, ensure that the support leg is
in stable contact with the floor. If necessary, adjust the passenger
seat.
* Refer to the current legislation in your country before installing a child
seat on this seat.
"FORWARD-FACING"
When a "forward-facing" child seat is installed on the front passenger
seat, adjust the vehicle's seat to the intermediate longitudinal and
highest position with seat backrest straightened and leave the
passenger's airbag activated.
Passenger seat adjusted to the intermediate longitudinal position.
5/ SAFETY
CHILD SEAT IN THE FRONT*
DEACTIVATING THE PASSENGER'S
FRONT AIRBAG
Never install a rearward facing child restraint system on a seat
protected by an active front airbag. This could cause the death of
the child or serious injury.
Passenger airbag OFF
120
The warning label present on both sides of the passenger's
sun visor repeats this advice. In line with current legislation,
the following tables contain this warning in all of the languages
required.
For information on deactivating the passenger's front airbag, refer
to the "Airbags" section.
НИКОГА НЕ инсталирайте детско столче на седалка с АКТИВИРАНА предна ВЪЗДУШНА ВЪЗГЛАВНИЦА. Това можеда причини СМЪРТ
или СЕРИОЗНО НАРАНЯВАНЕ на детето.
CS
NIKDY neumisťujte dětské zádržné zařízení orientované směrem dozadu na sedadlo chráněné AKTIVOVANÝM čelním AIRBAGEM. Hrozí
nebezpečí SMRTI DÍTĚTE nebo VÁŽNÉHO ZRANĚNÍ.
DA
Brug aldrig en bagudvendt barnestol på et sæde der er beskyttet af en aktiv airbag. Død eller alvorlig skade på barnet kan forekomme.
DE
Verwenden Sie NIEMALS einen Kindersitz oder Babyschale gegen die Fahrtrichtung bei AKTIVIERTEM Airbag, TOD oder ERNSTHAFTE
VERLETZUNGEN können die Folge sein.
EL
Μη χρησιμοποιείτε ΠΟΤΕ παιδικό κάθισμα με την πλάτη του προς το εμπρός μέρος του αυτοκινήτου, σε μια θέση που προστατεύεται από
ΜΕΤΩΠΙΚΟ αερόσακο που είναι ΕΝΕΡΓΟΣ. Αυτό μπορεί να έχει σαν συνέπεια το ΘΑΝΑΤΟ ή το ΣΟΒΑΡΟ ΤΡΑΥΜΑΤΙΣΜΟ του ΠΑΙΔΙΟΥ
EN
NEVER use a rearward facing child restraint on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the CHILD
can occur
ES
NO INSTALAR NUNCA EL SISTEMA DE RETENCIÓN PARA NIÑOS DE ESPALDAS AL SENTIDO DE LA CIRCULACIÓN SOBRE UN
ASIENTO PROTEGIDO CON UN COJÍN INFLABLE FRONTAL ( AIRBAG ) ACTIVADO. ESTO PUEDE CAUSAR LA MUERTE DEL BEBE O
HERIRLO GRAVEMENTE.
ET
Ärge kasutage kunagi lapse turvatooli seljaga sõidusuunas sõiduki istmel mis on kaitstud AKTIVEERITUD TURVAPADJAGA. See võib
põhjustada lapsele RASKEID VIGASTUSI või SURMA.
FI
ÄLÄ KOSKAAN aseta lapsen turvaistuinta selkä ajosuuntaan istuimelle, jonka edessä suojana on käyttöön aktivoitu TURVATYYNY. Sen
laukeaminen voi aiheuttaa LAPSEN KUOLEMAN tai VAKAVAN LOUKKAANTUMISEN.
FR
NE JAMAIS installer de système de retenue pour enfants faisant face vers l’arrière sur un siège protégé par un COUSSIN GONFLABLE frontal
ACTIVÉ.
Cela peut provoquer la MORT de l’ENFANT ou le BLESSER GRAVEMENT
HR
NIKADA ne postavljati dječju sjedalicu leđima u smjeru vožnje na sjedalo zaštićeno UKLJUČENIM prednjim ZRAČNIM JASTUKOM. To bi moglo
uzrokovati SMRT ili TEŠKU OZLJEDU djeteta.
HU
SOHA ne használjon menetiránynak háttal beszerelt gyermekülést olyan ülésen, amely AKTIVÁLT ÁLLAPOTÚ (BEKAPCSOLT)
FRONTLÉGZSÁKKAL van védve. Ez a gyermek halálát vagy súlyos sérülését okozhatja.
IT
NON installare MAI seggiolini per bambini posizionati in senso contrario a quello di marcia su un sedile protetto da un AIRBAG frontale
ATTIVATO. Ciò potrebbe provocare la MORTE o FERITE GRAVI al bambino.
LT
NIEKADA neįrenkite vaiko prilaikymo priemonės su atgal atgręžtu vaiku ant sėdynės, kuri saugoma VEIKIANČIOS priekinės ORO PAGALVĖS.
Išsiskleidus oro pagalvei vaikas gali būti MIRTINAI arba SUNKIAI TRAUMUOTAS.
LV
NAV PIEĻAUJAMS uzstādīt uz aizmuguri vērstu bērnu sēdeklīti priekšējā pasažiera vietā, kurā ir AKTIVIZĒTS priekšējais DROŠĪBAS GAISA
SPILVENS.
Tas var izraisīt BĒRNA NĀVI vai radīt NOPIETNUS IEVAINOJUMUS.
5/ SAFETY
AR
BG
122
MT
Qatt m’ghandek thalli tifel/tifla marbut f’siggu dahru lejn l-Airbag attiva, ghaliex tista’ tikkawza korriment serju jew anke mewt lit-tifel/tifla
NL
Plaats NOOIT een kinderzitje met de rug in de rijrichting op een zitplaats waarvan de AIRBAG is INGESCHAKELD. Bij het afgaan van de airbag
kan het KIND ERNSTIG OF DODELIJK GEWOND raken.
NO
Installer ALDRI et barnesete med ryggen mot kjøreretningen i et sete som er beskyttet med en frontal AKTIVERT KOLLISJONSPUTE, BARNET
risikerer å bli DREPT eller HARDT SKADET.
PL
NIGDY nie instalować fotelika dziecięcego w pozycji «tyłem do kierunku jazdy»na siedzeniu wyposażonym w CZOŁOWĄ PODUSZKĘ
POWIETRZNĄ w stanie AKTYWNYM.W przeciwnym razie dziecko narażone będzie na ŚMIERĆ lub BARDZO POWAŻNE OBRAŻENIA CIAŁA
w momenicie wyzwolenia poduszki powietrznej
PT
NUNCA instale um sistema de retenção para crianças de costas para a estrada, num banco protegido por um AIRBAG frontal ACTIVADO. Esta
instalação poderá provocar FERIMENTOS GRAVES ou a MORTE da CRIANÇA.
RO
Nu instalati NICIODATA un sistem de retinere pentru copii, dispus cu spatele in directia de mers, pe un loc din vehicul protejat cu AIRBAG frontal
ACTIVAT. Aceasta ar putea provoca MOARTEA COPILULUI sau RANIREA lui GRAVA.
RU
ВО ВСЕХ СЛУЧАЯХ ЗАПРЕЩАЕТСЯ использовать обращенное назад детское удерживающее устройство на сиденье, защищенном
ФУНКЦИОНИРУЮЩЕЙ ПОДУШКОЙ БЕЗОПАСНОСТИ, установленной перед этим сиденьем.
Это может привести к ГИБЕЛИ РЕБЕНКА или НАНЕСЕНИЮ ЕМУ СЕРЬЕЗНЫХ ТЕЛЕСНЫХ ПОВРЕЖДЕНИЙ
SK
NIKDY nepoužívajte na prednom sedadle chránenom AKTÍVNYM AIRBAGOM detské zadržiavacie zariadenie umiestnené v proti smere jazdy.
Môže to spôsobiť SMRŤ, alebo VÁŽNE ZRANENIE DIEŤAŤA.
SL
NIKOLI ne nameščajte otroškega sedeža s hrbtom v smeri vožnje, če je VARNOSTNA BLAZINA pred sprednjim sopotnikovim sedežem
AKTIVIRANA. Takšna namestitev lahko povzroči SMRT OTROKA ali HUDE POŠKODBE.
SR
NIKADA ne koristite dečje sedište koje se okreće unazad na sedištu zaštićenim AKTIVNIM VAZDUŠNIM JASTUKOM ispred njega, jer mogu
nastupiti SMRT ili OZBILJNA POVREDA DETETA.
SV
Använd ALDRIG en bakåtvänd barnstol i ett säte skyddat av en AKTIV AIRBAG framför det. Det kan orsaka ALLVARLIGA eller DÖDLIGA skador
på barnet.
TR
KESİNLKLE HAVA YASTIĞI AKTİF olan ön koltuğa yüzü arkaya dönük bir çocuk koltuğu yerleştirmeyiniz. Bu ÇOCUĞUN ÖLMESİNE veya ÇOK
AĞIR YARALANMASINA sebep olabilir.
CHILD SEATS RECOMMENDED BY PEUGEOT
PEUGEOT offers a complete range of recommended child seats which are secured using a three point seat belt:
Group 0+: from birth to 13 kg
L1
"RÖMER Baby-Safe Plus"
Installed in the rearward facing position.
L4
"KLIPPAN Optima"
From about 6 years (from 22 kg),
the booster is used on its own.
L5
"RÖMER KIDFIX"
Can be fixed to the vehicle's
ISOFIX mouintings
The child is held by the seat belt.
5/ SAFETY
Groups 2 and 3: from 15 to 36 kg
LOCATIONS FOR CHILD SEATS SECURED USING THE SEAT BELT
In accordance with European regulations, this table indicates the options for the installation of child seats secured using the seat belt and universally
approved (a) in relation to the weight of the child and the seat in the vehicle.
Weight of the child /indicative age
124
Seat
Front passenger seat (c)
Outer rear seats
Less than 13 kg
(groups 0 (b) and 0+)
Up to 1 year approx
From 9 to 18 kg
(group 1)
From 1 to 3 years
approx
From 15 to 25 kg
(group 2)
From 3 to 6 years
approx
From 22 to 36 kg
(group 3)
From 6 to 10 years approx
U(R)
U(R)
U(R)
U(R)
X
X
X
X
(a) Universal child seat: child seat which can be installed in all vehicles using the seat belt.
(b) Group 0: from birth to 10 kg. Infant car seats and "car" cots cannot be installed on the front passenger seat.
(c) Consult the legislation in force in your country before installing your child on this seat.
U(R): seat suitable for the installation of a child seat secured using the seat belt and universally approved "rearward facing" and/or "forward facing",
with the seat adjusted to its highest position.
X: seat not suited to the installation of a child seat for the weight group indicated.
"ISOFIX" MOUNTINGS
Your vehicle has been approved to the latest ISOFIX regulations.
The seats represented below are fitted with regulation ISOFIX
mountings:
The incorrect installation of a child seat in a vehicle compromises
the child's protection in the event of an accident.
Observe strictly the fitting instructions in the installation guide
provided with the child seat.
For information regarding the possibilities for installing ISOFIX
child seats in your vehicle, refer to the table.
5/ SAFETY
These are three rings for each seat:
two rings A, located between the vehicle seat back and cushion,
indicated by a label,
a ring B referred to as the TOP TETHER, located under a cover
behind the top of the backrest for fixing the upper strap.
This ISOFIX mounting system provides fast, reliable and safe fitting of
the child seat in your vehicle.
The ISOFIX child seats are fitted with two locks which are secured
easily on the two rings A.
Some also have an upper strap which is attached to ring B.
To secure the child seat to the TOP TETHER:
open the cover at the top of the backrest,
fix the hook on the upper strap to the ring B,
tighten the upper strap.
ISOFIX CHILD SEAT
RECOMMENDED BY PEUGEOT AND APPROVED FOR YOUR VEHICLE
ISOFIX child seat with TOP TETHER
RÖMER Duo Plus ISOFIX
(size category B1)
126
Group 1: from 9 to 18 kg
Installed only in the "forward facing" position.
Is attached to the rings A, as well as the ring B, referred to as the TOP TETHER, using an
upper strap.
Three seat body angles: sitting, reclining, lying.
This child seat can also be used on seats which are not fitted with ISOFIX mountings.
In this case, it must be attached to the vehicle seat using the three point seat belt.
Adjust the front seat of the vehicle so that the child's feet do not touch the backrest.
Follow the instructions for fitting the child seat given in the seat manufacturer's installation guide.
LOCATIONS FOR FITTING ISOFIX CHILD SEATS
In accordance with European Regulations, this table indicates the options for installing ISOFIX child seats on seats in the vehicle fitted with ISOFIX
mountings.
In the case of universal and semi-universal ISOFIX child seats, the ISOFIX size category, determined by a letter from A to G, is indicated on the
child seat next to the ISOFIX logo.
Weight of the child / indicative age
ISOFIX size category
ISOFIX universal and semiuniversal child seats which can be
installed on the outer rear seats
Less than 10 kg
(group 0)
Less than 13 kg
(group 0+)
Up to approx. 1 year
Infant car seat*
"rear facing"
F
G
C
X
D
X
From 9 to 18 kg
(group 1)
From approx. 1 to 3 years
"rear facing"
E
C
D
X
IUF: seat suitable for the installation of an Isofix Universal "Forwards-facing" child seat with a top tether.
It may be necessary to move the front seat forwards to facilitate the installation of a child seat on a rear seat.
X: seat which is not suitable for the installation of an ISOFIX seat of the size category indicated.
* Infant car seats and "car" cots cannot be installed on the front passenger seat.
"forward facing"
A
B
B1
IUF
5/ SAFETY
Type of ISOFIX child seat
Less than 10 kg
(group 0)
Up to approx. 6 months
ADVICE ON CHILD SEATS
128
The incorrect installation of a child seat in a vehicle compromises
the child's protection in the event of an accident.
When installing a child seat using the seat belt, ensure that the
seat belt is tightened correctly on the child seat and that it secures
the child seat firmly on the vehicle's seat.
Remember to fasten the seat belts or the child seat harnesses
keeping the slack in relation to the child's body to a minimum,
even for short journeys.
For optimum installation of the "forward facing" child seat, ensure
that the back of the child seat is as close as possible to the
backrest of the vehicle's seat, even in contact if possible.
Children at the front
The legislation on carrying children on a front passenger seat is
specific to each country. Refer to the legislation in force in your
country.
Deactivate the passenger airbag when a "rearward facing" child seat
is installed on the front seat. Otherwise, the child would risk being
seriously injured or killed if the airbag were to inflate.
Installation of a booster seat
The chest part of the seat belt must be positioned on the child's
shoulder without touching the neck.
Ensure that the lap part of the seat belt passes correctly over the
child's thighs.
PEUGEOT recommends the use of a booster seat which has a back,
fitted with a seat belt guide at shoulder level.
As a safety precaution, do not leave:
one or more children alone and unsupervised in a vehicle,
a child or an animal in a vehicle which is exposed to the sun,
with the windows closed,
the keys within reach of children inside the vehicle.
IGNITION SWITCH
ELECTRONIC ENGINE IMMOBILISER
The key contains an electronic chip which has a special code. When
the ignition is switched on, this code must be recognised in order for
starting to be possible.
A few minutes after the ignition is switched off, this electronic engine
immobiliser locks the engine management system and prevents starting
of the engine by anyone who does not have the key.
STARTING THE VEHICLE
 Insert the key in the ignition switch.
The system recognises the starting code.
 Turn the key fully towards the dashboard to position 3 (Starting).
 When the engine starts, release the key.
SWITCHING THE VEHICLE OFF
 Immobilise the vehicle.
 Turn the key fully towards you to position 1 (Stop).
 Remove the key from the ignition switch.
Key left in the "Ignition on" position
On opening the driver's door, an alert message is displayed,
accompanied by an audible signal, to remind you that the key is
still in the ignition switch at position 1 (Stop).
If the key has been left in the ignition switch at position 2 (Ignition
on), the ignition will be switched off automatically after one hour.
To switch the ignition back on, turn the key to position 1 (Stop),
then back to position 2 (Ignition on).
Switching off the engine leads to a loss of braking assistance.
6/ DRIVING
In the event of a malfunction, you are informed by lighting of this
warning lamp, an audible signal and a message on the screen.
In this case, your vehicle does not start; contact a PEUGEOT
dealer as soon as possible.
PARKING BRAKE
Releasing
 Pull the parking brake lever gently, press the release button then
lower the lever fully.
When the vehicle is being driven, if this warning lamp and the
STOP warning lamp come on, accompanied by an audible
signal and a message in the screen, this indicates that the
parking brake is still on or has not been properly released.
130
Applying
 Pull the parking brake lever fully up to immobilise your vehicle.
When parking on a slope, direct your wheels against the
pavement, apply the parking brake and engage a gear.
HILL START ASSIST
System which keeps your vehicle immobilised temporarily
(approximately 2 seconds) when starting on a gradient, the time it takes
to move your foot from the brake pedal to the accelerator pedal.
This function is only active when:
the vehicle is completely stationary, with your foot on the brake
pedal,
certain conditions of slope are met,
with the driver’s door closed.
The hill start assist system cannot be deactivated.
OPERATION
On a descending slope, with the vehicle stationary and reverse
gear engaged, the vehicle is held for a brief moment when you
release the brake pedal.
Do not exit the vehicle while it is being held in the hill start assist
phase.
OPERATING FAULT
On an ascending slope, with the vehicle stationary, the vehicle is
held for a brief moment when you release the brake pedal:
provided you are in first gear or neutral on a manual gearbox,
provided you are in position D or M on an automatic gearbox.
If a malfunction of the system occurs, these warning lamps come on.
Have it checked by a PEUGEOT dealer or a qualified workshop.
6/ DRIVING
If you need to exit the vehicle with the engine running,
apply the parking brake and then check that the
corresponding warning lamp in the instrument panel is on.
6-SPEED MANUAL GEARBOX
ENGAGING 5TH OR 6TH GEAR
132
 Move the lever fully to the right to engage 5th or 6th gear.
ENGAGING REVERSE GEAR
 Raise the ring under the knob and move the gear lever to the left
then forwards.
Only engage reverse gear when the vehicle is stationary with the engine
at idle.
As a safety precaution and to facilitate starting of the engine:
always select neutral,
press the clutch pedal.
"PORSCHE TIPTRONIC SYSTEM"
AUTOMATIC GEARBOX
GEAR LEVER POSITIONS
GEAR SELECTION GATE
1.
2.
3.
Gear lever.
Button "S" (sport).
Button "" (snow).
P. Park.
Immobilisation of the vehicle, parking brake on or off.
Starting the engine.
R. Reverse.
Reversing manoeuvres, vehicle stationary, engine at idle.
N. Neutral.
Immobilisation of the vehicle, parking brake on.
Starting the engine.
D. Automatic operation.
M. + / - Manual operation with sequential changing of the six gears.
 Press forwards to change up through the gears.
or
 Press rearwards to change down through the gears.
6/ DRIVING
Six speed automatic gearbox which offers a choice between the comfort
of fully automatic operation, enhanced by sport and snow programmes,
or manual gear changing.
There are two driving modes:
automatic operation for electronic management of the gears by
the gearbox, with the sport programme for a more dynamic driving
style or the snow programme to facilitate driving when grip is poor.
manual operation for sequential changing of the gears by the
driver.
DISPLAYS IN THE INSTRUMENT PANEL
3
134
3
When you move the lever in the gate to select a position, the
corresponding symbol is displayed in the instrument panel.
P. Park
R. Reverse
N. Neutral
D1... D6. Drive (Automatic driving)
S. Sport programme
. Snow programme
M1... M6. Manual (Sequential driving)
-. Invalid value during manual operation
MOVING OFF
 Apply the parking brake.
 Select position P or N.
 Start the engine.
If this procedure is not followed, there is an audible signal, accompanied
by a message in the screen.
 With the engine running, press the brake pedal.
 Release the parking brake.
 Select position R, D or M,
 Gradually release the brake pedal.
The vehicle then moves off.
A message is displayed if you try to move the gear lever from
position P without pressing the brake pedal.
If position N is engaged inadvertently while driving, allow the
engine to return to idle then engage position D to accelerate.
When the engine is running at idle, with the brakes released, if
position R, D or M is selected, the vehicle moves even without the
accelerator being pressed.
When the engine is running, never leave children in the vehicle
without supervision.
When carrying out maintenance with the engine running, apply the
parking brake and select position P.
AUTOMATIC OPERATION
Sport programme "S"
 Select position D for automatic changing of the six gears.
 Press button "S", after starting the engine.
The gearbox automatically favours a dynamic style of driving.
The gearbox then operates in auto-adaptive mode, without any
intervention on the part of the driver. It continuously selects the most
suitable gear according to the style of driving, the profile of the road and
the load in the vehicle.
D and the gears selected automatically appear in succession in the
instrument panel.
For maximum acceleration without touching the lever, press the
accelerator pedal down fully (kick down). The gearbox changes down
automatically or maintains the gear selected until the maximum engine
speed is reached.
On braking, the gearbox changes down automatically to provide
efficient engine braking.
If you release the accelerator sharply, the gearbox will not change to a
higher gear for safety reasons.
3
S appears in the instrument panel.
Snow programme ""
 Press button "", after starting the engine.
The gearbox adapts to driving on slippery roads.
This programme improves starting and drive when traction is poor.
3
 appears in the instrument panel.
RETURN TO AUTOMATIC OPERATION
 At any time, press the button selected again to quit the programme
engaged and return to auto-adaptive mode.
MANUAL OPERATION
SPORT AND SNOW PROGRAMMES
These two special programmes supplement the automatic operation in
very specific conditions of use.
 Select position M for sequential changing of the six gears.
 Push the lever towards the + sign to change up a gear.
 Pull the lever towards the - sign to change down a gear.
6/ DRIVING
Never select position N while the vehicle is moving.
Never select positions P or R unless the vehicle is completely
stationary.
It is only possible to change from one gear to another if the vehicle
speed and engine speed permit; otherwise, the gearbox will operate
temporarily in automatic mode.
136
M and the gears engaged manually appear in succession in
the instrument panel.
If the engine speed is too low or too high, the gear selected
flashes for a few seconds, then the actual gear engaged is
displayed.
It is possible to change from position D (automatic) to position M
(manual) at any time.
When the vehicle is stationary or moving very slowly, the gearbox
selects gear M1 automatically.
The sport and snow programmes do not operate in manual mode.
Invalid value during manual operation
This symbol is displayed if a gear is not engaged correctly
(selector between two positions).
STOPPING THE VEHICLE
Before switching off the engine, you can engage position P or N to
place the gearbox in neutral.
In both cases, apply the parking brake to immobilise the vehicle.
If the lever is not in position P, when the driver's door is opened or
approximately 45 seconds after the ignition is switched off, there is
an audible signal is heard accompanied by a message.
 Return the lever to position P; the audible signal stops and the
message disappears.
OPERATING FAULT
When the ignition is on, the illumination of this warning lamp,
accompanied by an audible signal and a message in the
screen, indicates a gearbox malfunction.
In this case, the gearbox switches to emergency mode and is locked in
3rd gear. You may feel a substantial knock when changing from P to R
and from N to R. This will not cause any damage to the gearbox.
Do not exceed a speed of 60 mph (100 km/h), local speed restrictions
permitting.
Have it checked by a PEUGEOT dealer or a qualified workshop.
This warning lamp may also come on if a door is opened.
There is a risk of damage to the gearbox:
if you press the accelerator and brake pedals at the same
time,
if you force the lever from position P to another position when
the battery is flat.
To reduce fuel consumption during a long period stationary with
the engine running (traffic jam, etc.), place the gear lever in
position N and apply the parking brake.
GEAR EFFICIENCY INDICATOR
System which reduces fuel consumption by recommending the most
appropriate gear.
With an automatic gearbox, the system is only active in manual mode.
Example:
You are in third gear.
You press the accelerator pedal.
The system may suggest that you engage a higher gear.
OPERATION
The information appears in the instrument panel in the form of an arrow.
On vehicle fitted with a manual gearbox, the arrow may be
accompanied by the gear recommended.
The system adapts its gear change recommendation according
to the driving conditions (slope, load, ...) and the demands of the
driver (power, acceleration, braking, ...).
The system never suggests:
engaging first gear,
engaging reverse gear,
6/ DRIVING
Depending on the driving situation and your vehicle's equipment, the
system may advise you to skip one (or more) gear(s). You can follow
this instruction without engaging the intermediate gears.
The gear engagement recommendations must not be considered
compulsory. In fact, the configuration of the road, the amount of traffic
and safety remain determining factors when choosing the best gear.
Therefore, the driver remains responsible for deciding whether or not
to follow the advice given by the system.
This function cannot be deactivated.
TYRE UNDER-INFLATION DETECTION
System which automatically checks the pressures of the tyres while
driving.
The system continuously monitors the pressures of the four tyres, as
soon as the vehicle is moving.
This system does not avoid the need to check the tyre pressures
regularly (including the spare wheel) and before a long journey.
Driving with under-inflated tyres adversely affects road holding,
extends braking distances and causes premature tyre wear,
particularly under arduous conditions (vehicle loaded, high speed,
long journey).
138
Driving with under-inflated tyres increases fuel consumption.
A pressure sensor is located in the valve of a each tyres (except the
spare wheel).
The system triggers an alert if a drop in pressure is detected in
one or more tyres.
The tyre under-inflation detection system is an aid to driving which
does not replace the need for the driver to be vigilant or to drive
responsibly.
The tyre pressures for your vehicle can be found on the tyre
pressure label (see the "Identification markings" section).
The tyre pressures must be checked when the tyres cold (vehicle
stopped for 1 hour or after driving for less then 6 miles (10 km) at
moderate speed). Otherwise, add 0.3 bar to the values indicated
on the label.
UNDER-INFLATION ALERT
OPERATING FAULT
The alert is given by the fixed illumination of this warning
lamp, accompanied by an audible signal, and depending on
equipment, the display of a message.
In the event of a problem on one of the tyres, the symbol or the
message appears, according to equipment, to identify it.
 Reduce speed, avoid sudden steering movements or harsh brake
applications.
 Stop as soon as it is safe to do so.
 In the event of a puncture, use the temporary puncture repair kit
or the spare wheel (according to equipment),
or
 if you have a compressor, the one in the temporary puncture repair
kit for example, check the four tyre pressures when cold,
or
 if it is not possible to check the tyre pressures at the time, drive
carefully at reduced speed.
The flashing and then fixed illumination of the
under-inflation warning lamp accompanied by the
illumination of the "service" warning lamp indicates a
fault with the system.
In this case, monitoring of the tyre pressures is not assured.
The alert is maintained until the tyre or tyres concerned is reinflated,
repaired or replaced.
The spare wheel (space-saver type or a steel rim) does not have a
sensor.
Go to a PEUGEOT dealer or a qualified workshop to have the system
checked or, following the repair of a puncture, to have the original
wheel, equipped with a sensor, refitted.
6/ DRIVING
The loss of pressure detected does not always lead to visible
deformation of the tyre. Do not rely on just a visual check.
This alert is also displayed when one or more wheels is not fitted
with a sensor (for example, a space-saver or steel spare wheel).
SPEED LIMITER
STEERING MOUNTED CONTROL
System which prevents the vehicle from exceeding the speed
programmed by the driver.
When the programmed speed limit is reached, pressing the accelerator
pedal no longer has any effect.
The speed limiter is switched on manually: it requires a programmed
speed of at least 20 mph (30 km/h).
140
The speed limiter is switched off by manual operation of the control.
The programmed speed can be exceeded temporarily by pressing the
accelerator firmly.
To return to the programmed speed, simply slow down to a speed below
the programmed speed.
The programmed speed remains in the memory when the ignition is
switched off.
The speed limiter cannot, in any circumstances, replace the need
to respect speed limits, nor can it replace the need for vigilance
and responsibility on the part of the driver.
The functions of this system are grouped together on steering mounted
control.
1. Speed limiter mode selection dial.
2. Value decrease button.
3. Value increase button.
4. Speed limiter on / off button.
The programmed information is grouped together in the instrument
panel screen.
5. Speed limiter on / off indication.
6. Speed limiter mode selection indication.
7. Programmed speed value.
PROGRAMMING
 Turn dial 1 to the "LIMIT" position: the speed
limiter mode is selected but is not switched on
(OFF / Pause).
You do not have to switch the speed limiter on in order
to set the speed.
 Set the speed value by pressing button 2 or 3
(e.g.: 55 mph (90 km/h)).
You can then change the programmed speed using
buttons 2 and 3:
by + or - 1 mph (km/h) = short press,
by + or - 5 mph (km/h) = long press,
in steps of + or - 5 mph (km/h) = maintained press.
 Switch the speed limiter on by pressing button 4.
 Switch the speed limiter off by pressing button 4: the display
confirms that it has been switched off (OFF / Pause).
 Switch the speed limiter back on by pressing
button 4 again.
6/ DRIVING
DISPLAYS IN THE INSTRUMENT PANEL
EXCEEDING THE PROGRAMMED SPEED
Pressing the accelerator pedal to exceed the
programmed speed will not have any effect unless
you press the pedal firmly past the point of
resistance.
The speed limiter is deactivated temporarily and the programmed
speed, which is still displayed, flashes.
Returning to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically cancels the
flashing of the programmed speed.
142
EXITING THE SPEED LIMITER MODE
 Turn dial 1 to the "0" position: the speed limiter mode is deselected.
It disappears from the display.
OPERATING FAULT
In the event of a speed limiter malfunction, the speed is cleared
resulting in flashing of the dashes.
Have it checked by a PEUGEOT dealer or a qualified workshop.
On a steep descent or in the event of sharp acceleration,
the speed limiter will not be able to prevent the vehicle from
exceeding the programmed speed.
To avoid any risk of jamming of the pedals:
ensure that the mat is positioned correctly,
do not fit one mat on top of another.
CRUISE CONTROL
STEERING MOUNTED CONTROL
System which automatically maintains the speed of the vehicle at the
value programmed by the driver, without any action on the accelerator
pedal.
The cruise control is switched on manually: it requires a minimum
vehicle speed of 25 mph (40 km/h) and the engaging:
of fourth gear on the manual gearbox,
of second gear on the automatic gearbox, in sequential driving
mode,
of position D on the automatic gearbox.
The cruise control is switched off manually or by pressing the brake or
clutch pedal or on triggering of the trajectory control system for safety
reasons.
It is possible to exceed the programmed speed temporarily by pressing
the accelerator pedal.
To return to the programmed speed, simply release the accelerator
pedal.
The functions of this system are grouped together on the steering
mounted control.
1. Cruise control mode selection dial.
2. Speed programming / value decrease button.
3. Speed programming / value increase button.
4. Cruise control off / resume button.
The cruise control cannot, in any circumstances, replace the need
to respect speed limits, nor can it replace the need for vigilance
and responsibility on the part of the driver.
You are advised to keep your feet near the pedals at all times.
6/ DRIVING
Switching off the ignition cancels any programmed speed value.
144
DISPLAYS IN THE INSTRUMENT PANEL
The programmed information is grouped together in the instrument
panel screen.
5. Cruise control off / resume indication.
6. Cruise control mode selection indication.
7. Programmed speed value.
PROGRAMMING
 Turn dial 1 to the "CRUISE" position: the cruise
control mode is selected but is not switched on
(OFF / Pause).
 Set the programmed speed by accelerating to
the required speed, then press button 2 or 3
(e.g.: 70 mph (110 km/h)).
You can then change the programmed speed using
buttons 2 and 3:
by + or - 1 mph (km/h) = short press,
by + or - 5 mph (km/h) = long press,
in steps of + or - 5 mph (km/h) = maintained press.
 Switch off the cruise control by pressing
button 4: the display confirms that it has been
switched off (OFF / Pause).
 Switch the cruise control back on by pressing
button 4 again.
EXCEEDING THE PROGRAMMED SPEED
Intentional or unintentional exceeding of the
programmed speed results in flashing of this speed in
the screen.
Return to the programmed speed, by means of
intentional or unintentional deceleration of the vehicle, automatically
cancels the flashing of the speed.
OPERATING FAULT
In the event of a cruise control malfunction, the speed is cleared
resulting in flashing of the dashes.
Have it checked by a PEUGEOT dealer or a qualified workshop.
EXITING CRUISE CONTROL MODE
When the cruise control is switched on, be careful if you maintain
the pressure on one of the programmed speed changing buttons:
this may result in a very rapid change in the speed of your vehicle.
Do not use the cruise control on slippery roads or in heavy traffic.
On a steep descent, the cruise control will not be able to prevent
the vehicle from exceeding the programmed speed.
To avoid any risk of jamming of the pedals:
ensure that the mat is positioned correctly,
never fit one mat on top of another.
6/ DRIVING
 Turn dial 1 to the "0" position: the cruise control mode is
deselected. It disappears from the display.
PARKING SENSORS
This system indicates the proximity of an obstacle (person, vehicle, tree,
gate, etc.) which comes within the field of detection of sensors located
in the bumper.
REAR PARKING SENSORS
The system is switched on by engaging reverse gear. This is
accompanied by an audible signal.
The system is switched off when you come out of reverse gear.
This function cannot, in any circumstances, take the place of the
vigilance and responsibility of the driver.
146
Audible assistance
The proximity information is given by an intermittent audible signal, the
frequency of which increases as the vehicle approaches the obstacle.
The sound emitted by the speaker (right or left) indicates the side on
which the obstacle is located.
When the distance between the vehicle and the obstacle becomes
less than approximately thirty centimetres, the audible signal becomes
continuous.
Certain types of obstacle (stake, roadworks cone, etc.) detected
initially will no longer be detected at the end of the manoeuvre due
to the presence of blind spots.
Visual assistance
FRONT PARKING SENSORS
In addition to the rear parking sensors, the front parking sensors are
triggered when an obstacle is detected in front and the speed of the
vehicle is still below 6 mph (10 km/h).
The front parking sensors are interrupted if the vehicle stops for more
than three seconds in forward gear, if no further obstacles are detected
or when the speed of the vehicle exceeds 6 mph (10 km/h).
The sound emitted by the speaker (front or rear) indicates whether the
obstacle is in front or behind.
Deactivation / Activation of the front and rear parking sensors
The function is deactivated by pressing this button. The indicator lamp
in the button comes on.
Pressing this button again reactivates the function. The indicator lamp in
the button goes off.
6/ DRIVING
This supplements the audible signal by displaying bars in the
multifunction screen which move progressively nearer to the vehicle.
When the obstacle is near, the "Danger" symbol is displayed in the
screen.
Deactivation / Activation of the rear parking sensors
The function is deactivated or activated via the vehicle configuration
menu.
The status of the function is stored when the ignition is switched off.
148
The function will be deactivated automatically if a trailer is being
towed or a bicycle carrier is fitted (vehicle fitted with a towbar or
bicycle carrier recommended by PEUGEOT).
OPERATING FAULT
In the event of a malfunction of the system, when reverse gear
is engaged this warning lamp is displayed in the instrument
panel and/or a message appears in the screen, accompanied
by an audible signal (short beep).
Contact a PEUGEOT dealer or a qualified workshop.
In bad weather or in winter, ensure that the sensors are not
covered with mud, ice or snow. When reverse gear is engaged, an
audible signal (long beep) indicates that the sensors may be dirty.
Certain sound sources (motorcycle, lorry, pneumatic drill, etc.)
may trigger the audible signals of the parking sensor system.
PEUGEOT & TOTAL
PARTNERS IN PERFORMANCE
AND PROTECTION OF
THE ENVIRONMENT
Innovation at the service of performance
The TOTAL Research and Development teams
develop lubricants for PEUGEOT which satisfy the
requirements of the latest technical innovations
incorporated in PEUGEOT vehicles.
This ensures that you obtain the best performance
and the maximum engine life.
Reduced exhaust emissions
RECOMMENDS
7/ CHECKS
TOTAL lubricants are formulated to optimise the
efficiency of engines and the protection of the
emissions post-treatment systems. It is crucial to
observe the servicing recommendations made by
PEUGEOT to ensure correct operation.
FUEL TANK
Fuel tank capacity: approximately 55 litres.
150
LOW FUEL LEVEL
When the fuel tank minimum level is reached this warning
lamp comes on on the instrument panel, accompanied by an
audible signal and an alert message. When it first comes on
there remains approximately 5 litres of fuel in the tank.
Until sufficient fuel is added, this warning lamp appears every time
the ignition is switched on, accompanied by an audible signal and a
message. When driving, this audible signal and display of the alert
message are repeated with increasing frequency as the fuel level drops
towards "0".
Refuel as soon as possible to avoid running out of fuel.
If you run out of fuel (Diesel), refer also to the "Running out of fuel
(Diesel)" section.
FILLING
A label affixed to the inside of the flap reminds you of the type of fuel to
be used depending on your engine.
Additions of fuel must be of at least 5 litres, in order to be registered by
the fuel gauge.
Opening the filler cap may create a noise a caused by an inrush
of air. This vacuum is entirely normal, resulting from the sealing of
the fuel system.
To fill the tank in complete safety:
 the engine must be switched off,
 press the rear part of the flap, then raise it to open it,
 turn the cap to the left,
 remove the cap and hook it onto the clip located on the inside of
the flap,
 fill the tank, but do not continue after the 3rd cut-off of the
pump; this could cause malfunctions.
When you have filled the tank:
 put the cap back in place,
 turn it to the right,
 close the flap.
Freezing conditions
In these conditions, the filler flap may be jammed.
Opening the boot gives access to the flap, allowing it to be
released by hand.
QUALITY OF THE FUEL USED FOR DIESEL
ENGINES
The Diesel engines are perfectly compatible with biofuels which
conform to current and future European standards (Diesel fuel which
complies with standard EN 590 mixed with a biofuel which complies
with standard EN 14214) available at the pumps (containing up to
7 % Fatty Acid Methyl Ester).
The B30 biofuel can be used in certain Diesel engines; however, this
use is subject to strict application of the special servicing conditions.
Contact a PEUGEOT dealer or a qualified workshop.
The use of any other type of (bio)fuel (vegetable or animal oils, pure
or diluted, domestic fuel...) is strictly prohibited (risk of damage to the
engine and fuel system).
The petrol engines are perfectly compatible with E10 or E24 type petrol
biofuels (containing 10 % or 24 % ethanol), conforming to European
standards EN 228 and EN 15376.
E85 type fuels (containing up to 85 % ethanol) are reserved exclusively
for vehicles marketed for the use of this type of fuel (BioFlex vehicles).
The quality of the ethanol must comply with European standard
EN 15293.
For Brazil only, special vehicles are marketed to run on fuels containing
up to 100 % ethanol (E100 type).
7/ CHECKS
QUALITY OF THE FUEL USED FOR PETROL
ENGINES
BONNET
OPENING
152
 Open the front left door.
 Pull the interior release lever A, located at the bottom of the door
aperture.
 Push the exterior safety catch B to the left and raise the bonnet.
The bonnet is held open by the two side struts.
The location of the interior release lever prevents opening of the
bonnet while the front left door is closed.
When the engine is hot, handle the safety catch with care (risk of
burns).
CLOSING
 Lower the bonnet and release it at the end of its travel.
 Pull on the bonnet to check that it is fully latched.
Because of the presence of electrical equipment under the bonnet,
it is recommended that exposure to water (rain, washing, ...) be
limited.
PETROL ENGINES
1.
2.
3.
4.
5.
Power steering reservoir.
Screenwash and headlamp wash reservoir.
Coolant reservoir.
Brake fluid reservoir.
Battery / Fuses.
6.
7.
8.
9.
Fusebox.
Air filter.
Engine oil dipstick.
Engine oil filler cap.
7/ CHECKS
The various caps and covers allow access for checking the levels of the various fluids and for replacing certain components.
154
DIESEL ENGINE
The various caps and covers allow access for checking the levels of the various fluids, for replacing certain components and for priming the fuel system.
1.
2.
3.
4.
5.
6.
Power steering reservoir.
Screenwash and headlamp wash reservoir.
Coolant reservoir.
Brake fluid reservoir.
Battery / Fuses.
Fusebox.
7.
8.
9.
10.
11.
Air filter.
Engine oil dipstick.
Engine oil filler cap.
Priming pump.
Bleed screw.
RUNNING OUT OF FUEL (DIESEL)
2 LITRE HDI ENGINE








If the engine does not start first time, don't keep trying.
Operate the priming pump again, then the starter motor.


Fill the fuel tank with at least five litres of Diesel.
Open the bonnet.
If necessary, unclip the style cover for access to the priming pump.
Slacken the bleed screw.
Squeeze and release the priming pump repeatedly until fuel
appears in the transparent pipe.
Tighten the bleed screw.
Operate the starter until the engine starts (if the engine fails to start
at the first attempt, wait around 15 seconds before trying again).
If the engine fails to start after a few attempts, operate the priming
pump again, then the starter.
Put the style cover back in position and clip it in place, ensuring that
it has clipped correctly.
Close the bonnet.
7/ CHECKS
On vehicle fitted with HDi engines, the fuel system must be primed
if you run out of fuel; refer to the engine compartment view on the
"Diesel engine" page.
CHECKING LEVELS
Check all of these levels regularly, in line with the warranty and maintenance record. Top them up if necessary, unless otherwise indicated.
If a level drops significantly, have the corresponding system checked by a PEUGEOT dealer or a qualified workshop.
Take care when working under the bonnet, as certain areas of the engine may be extremely hot (risk of burns) and the cooling fan could start
at any time (even with the ignition off).
ENGINE OIL LEVEL
156
The check is carried out either when the ignition is switched
on using the oil level indicator in the instrument panel, or using
the dipstick.
To ensure that the reading is correct, your vehicle must be on
level ground and the engine must have been off for more than
30 minutes.
It is normal to top up the oil level between two services (or oil changes).
PEUGEOT recommends that you check the level, and top up if
necessary, every 3 000 miles (5 000 kms).
A = MAX
B = MIN
Checking using the dipstick
Refer to the "Petrol engine" or "Diesel engine" section for the location of
the dipstick in the engine compartment of your vehicle.
Take the dipstick by its coloured grip and remove it completely.
Wipe the end of the dipstick using a clean non-fluffy cloth.
Refit the dipstick and push fully down, then pull it out again to make
the visual check: the correct level is between the marks A and B.
If you find that the level is above the A mark or below the B mark, do
not start the engine.
If the level is above the MAX mark (risk of damage to the engine),
contact a PEUGEOT dealer or a qualified workshop.
If the level is below the MIN mark, you must top up the engine oil.
Oil grade
The oil must be the correct grade for your engine and conform to the
manufacturer's recommendations.
Refer to the "Petrol engine" or "Diesel engine" section to identify the
location of the oil filler cap in the engine compartment of your vehicle.
Unscrew the oil filler cap to reveal the filler aperture.
Add oil in small quantities, avoiding any spills on engine
components (risk of fire).
Wait a few minutes before checking the level again using the
dipstick.
Add more oil if necessary.
After checking the level, carefully refit the oil filler cap and the
dipstick in its tube.
After topping up the oil, the check when switching on the ignition with
the oil level indicator in the instrument panel is not valid during the
30 minutes after topping up.
Engine oil change
Refer to the warranty and maintenance record for details of the interval
for this operation.
In order to maintain the reliability of the engine and emission control
system, the use of additives in the engine oil is prohibited.
BRAKE FLUID LEVEL
The brake fluid level should be close to the "MAX" mark. If it is
not, check the brake pad wear.
Changing the fluid
Refer to the warranty and maintenance record for details of the interval
for this operation.
Fluid specification
The brake fluid must conform to the manufacturer's recommendations.
POWER STEERING FLUID LEVEL
The power steering fluid level should be close to the "MAX"
mark. With the engine cold, unscrew the cap to check the level.
7/ CHECKS
Topping up the engine oil level
COOLANT LEVEL
F
0
The coolant level should be close to the "MAX" mark but
should never exceed it.
When the engine is warm, the temperature of the coolant is regulated
by the fan.
The cooling fan may start after switching off the engine: take
care with articles and clothing that might become caught by the
fan blades.
158
In addition, as the cooling system is pressurised, wait at least one hour
after switching off the engine before carrying out any work.
To avoid any risk of scalding, unscrew the cap by two turns to allow the
pressure to drop. When the pressure has dropped, remove the cap and
top up the level.
Fluid specification
DIESEL FUEL ADDITIVE LEVEL (DIESEL WITH
PARTICLE EMISSIONS FILTER)
The additive reservoir low level is indicated by fixed illumination
of this warning lamp, accompanied by an audible signal and
a message that the particle emissions filter additive level is
too low.
Topping up
The reservoir must be topped up without delay by a PEUGEOT dealer
or a qualified workshop.
USED PRODUCTS
Avoid prolonged contact of used oil or fluids with the skin.
Most of these fluids are harmful to health or indeed very corrosive.
The coolant must conform to the manufacturer's recommendations.
SCREENWASH AND HEADLAMP WASH FLUID
In the case of vehicles fitted with headlamp washers, the low
fluid level is indicated by an audible signal and a message in
the instrument panel screen.
Top up the reservoir when you next stop the vehicle.
Fluid specification
For optimum cleaning and to avoid freezing, this fluid must not be
topped up with or replaced with plain water.
In wintry conditions, the use of an ethyl alcohol or methanol base fluid is
recommended.
Do not discard used oil or fluids into sewers or onto the ground.
Take used oil to a PEUGEOT dealer or a qualified workshop
(France) or to an authorised waste disposal site.
CHECKS
Unless otherwise indicated, check these components in accordance with
the warranty and maintenance record and according to your engine.
Otherwise, have them checked by a PEUGEOT dealer or a qualified
workshop.
The battery does not require any maintenance.
However, check that the terminals are clean and correctly
tightened, particularly in summer and winter.
When carrying out work on the battery, refer to the "Battery"
section for details of the precautions to be taken before disconnecting
the battery and following its reconnection.
AIR FILTER AND PASSENGER COMPARTMENT FILTER
Refer to the warranty and maintenance record for details of
the replacement intervals for these components.
Depending on the environment (e.g. dusty atmosphere) and
the use of the vehicle (e.g. city driving), replace them twice
as often if necessary.
A clogged passenger compartment filter may have an adverse effect
on the performance of the air conditioning system and generate
undesirable odours.
OIL FILTER
Replace the oil filter each time the engine oil is changed.
Refer to the warranty and maintenance record for details of
the replacement interval for this component.
PARTICLE EMISSION FILTER (DIESEL)
The start of saturation of the particle emissions filter is
indicated by the temporary illumination of this warning lamp,
accompanied by an audible signal and a message on the risk
of blockage of the particle emissions filter.
As soon as the traffic conditions permit, regenerate the filter by driving
at a speed of at least 40 mph (60 km/h) until the warning lamp goes off.
If the warning lamp stays on, refer to the "Additive level" section.
On a new vehicle, the first particle filter regeneration operations
may be accompanied by a "burning" smell, which is perfectly
normal.
Following prolonged operation of the vehicle at very low speed or
at idle, you may, in exceptional circumstances, notice the emission
of water vapour at the exhaust on acceleration. This does not
affect the behaviour of the vehicle or the environment.
7/ CHECKS
BATTERY
MANUAL GEARBOX
The gearbox does not require any maintenance (no oil
change).
Refer to the warranty and maintenance record for the details
of the level checking interval for this component.
AUTOMATIC GEARBOX
160
The gearbox does not require any maintenance (no oil
change).
Refer to the warranty and maintenance record for details of
the level checking interval for this component.
BRAKE DISC WEAR
For information on checking brake disc wear, contact a
PEUGEOT dealer or a qualified workshop.
PARKING BRAKE
If excessive travel or a loss of effectiveness of this system
is noticed, the parking brake must be checked, even
between two services.
Checking this system must be done by a PEUGEOT dealer
or a qualified workshop.
BRAKE PADS
Brake wear depends on the style of driving, particularly in
the case of vehicles used in town, over short distances.
It may be necessary to have the condition of the brakes
checked, even between vehicle services.
Unless there is a leak in the circuit, a drop in the brake fluid level
indicates that the brake pads are worn.
Only use products recommended by PEUGEOT or products of
equivalent quality and specification.
In order to optimise the operation of units as important as those
in the braking system, PEUGEOT selects and offers very specific
products.
After washing the vehicle, dampness, or in wintry conditions, ice
can form on the brake discs and pads: braking efficiency may
be reduced. Make light brake applications to dry and defrost the
brakes.
TEMPORARY PUNCTURE REPAIR
KIT
ACCESS TO THE KIT
This kit is installed in the storage box, under the boot floor.
8/ PRACTICAL INFORMATION
Complete system consisting of a compressor and a sealant cartridge
which permits temporary repair of a tyre so that you can drive to the
nearest garage.
It is designed to repair most punctures which could affect the tyre,
located on the tyre tread or shoulder.
162
DESCRIPTION OF THE KIT
A.
B.
C.
D.
E.
"Sealant" or "Air" position selector.
On "I" / off "O" switch.
Deflation button.
Pressure gauge (in bar and p.s.i.).
Compartment housing:
- a cable with adaptor for 12 V socket,
- various inflation adaptors for accessories, such as balls, bicycle
tyres...
F.
G.
H.
I.
Sealant cartridge.
White pipe with cap for repair.
Black pipe for inflation.
Speed limit sticker.
The speed limit sticker I must be affixed to the vehicle's steering
wheel to remind you that a wheel is in temporary use.
Do not exceed a speed of 50 mph (80 km/h) when driving with a
tyre repaired using this type of kit.
The vehicle's electric system allows the connection of a
compressor for long enough to inflate a tyre after a puncture repair
or for inflating a small inflatable accessory.
REPAIR PROCEDURE
 Switch off the ignition.
 Turn the selector A to the "sealant" position.
 Check that the switch B is in position "O".
 Uncoil the white pipe G fully.
 Unscrew the cap from the white pipe.
 Connect the white pipe to the valve of the tyre to be repaired.
Avoid removing any foreign bodies which have penetrated into
the tyre.
Take care, this product is harmful (e.g. ethylene-glycol,
colophony...) if swallowed and causes irritation to the eyes.
Keep this product out of the reach of children.
 Connect the compressor's electric plug to the vehicle's 12 V socket.
 Start the vehicle and leave the engine running.
8/ PRACTICAL INFORMATION
1. Sealing
164
 Switch on the compressor by moving the switch B to position "I"
until the tyre pressure reaches 2.0 bars.
The sealant is injected into the tyre under pressure; do not
disconnect the pipe from the valve during this operation (risk of
splashing).
Do not start the compressor before connecting the white pipe
to the tyre valve: the sealant product would be expelled through
the pipe.
If after around 5 to 7 minutes the pressure is not attained, this
indicates that the tyre is not repairable; contact a PEUGEOT
dealer or a qualified workshop for assistance.
 Remove the kit and screw the cap back on the white pipe.
Take care to avoid staining your vehicle with traces of fluid. Keep
the kit to hand.
 Drive immediately for approximately three miles (five kilometres),
at reduced speed (between 15 and 35 mph (20 and 60 km/h)), to
plug the puncture.
 Stop to check the repair and the tyre pressure using the kit.
Tyre under-inflation detection
If the vehicle is fitted with tyre under-inflation detection,
the under-inflation warning lamp will remain on after the wheel
has been repaired until the system is reinitialised by a PEUGEOT
dealer or a qualified workshop.
 Turn the selector A to the "air" position.
 Uncoil the black pipe H fully.
 Connect the black pipe to the valve of the wheel.
 Connect the compressor's electric plug to the vehicle's 12 V socket.
 Start the vehicle again and leave the engine running.
 Adjust the pressure using the compressor (to inflate: switch B
in position "I"; to deflate: switch B in position "O" and press
button C), in accordance with the vehicle's tyre pressure label
(located on the left hand door aperture).
A loss of pressure indicates that the puncture has not been fully
plugged; contact a PEUGEOT dealer or qualified workshop for
assistance.
 Remove and stow the kit.
 Drive at reduced speed (50 mph [80 km/h] max) limiting the
distance travelled to approximately 120 miles (200 km).
As soon as possible, go to a PEUGEOT dealer or a qualified
workshop.
You must inform the technician that you have used this kit. After
inspection, the technician will advise you on whether the tyre can
be repaired or if it must be replaced.
8/ PRACTICAL INFORMATION
2. Inflation
REMOVING THE CARTRIDGE
166
Beware of discharges of fluid.
The expiry date of the fluid is indicated on the cartridge.
The sealant cartridge is designed for single use; even if only partly
used, it must be replaced.
After use, do not discard the cartridge into the environment, take it
to an authorised waste disposal site or a PEUGEOT dealer.
Do not forget to obtain a new sealant cartridge, available from
PEUGEOT dealers or from a qualified workshop.




Stow the black pipe.
Detach the angled base from the white pipe.
Support the compressor vertically.
Unscrew the cartridge from the bottom.
CHECKING TYRE PRESSURES /
INFLATING ACCESSORIES
 Turn the selector A to the "Air" position.
 Uncoil the black pipe H fully.
 Connect the black pipe to the valve of the wheel or
accessory.
If necessary, fit one of the adaptors supplied with the kit first.
 Connect the compressor's electrical connector to the vehicle's 12 V
socket.
 Start the vehicle and let the engine run.
 Adjust the pressure using the compressor (to inflate: switch B
in position "I"; to deflate: switch B in position "O" and press
button C), according to the vehicle's tyre pressure label or the
accessory's pressure label.
 Remove the kit then stow it.
8/ PRACTICAL INFORMATION
You can also use the compressor, without injecting any product, to:
check or adjust the pressure of your tyres,
inflate other accessories (balls, bicycle tyres...).
CHANGING A WHEEL
TOOLS REQUIRED*
Security socket: for adaptation of the
wheelbrace to the special "security" bolts.
Specific to your vehicle, it is stored in the
glove box.
168
Wheelbrace: for removal of the wheel fixing
bolts.
Jack with integrated handle: for lifting the
vehicle.
Bolt cover removal tool: for removal of the
bolt finishers (covers) on alloy wheels.
* Depending on the country of sale, the vehicle may be equipped with
the tools needed to change a wheel and a spare wheel (see following
pages).
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground
must be level, stable and non-slippery ground.
Apply the parking brake, switch off the ignition and engage first
gear (position P for the automatic gearbox) to lock the wheels.
It is imperative that you ensure that the occupants get out of the
vehicle and wait where they are safe.
If necessary, place a chock under the wheel diagonally opposite
the wheel to be changed.
Never go underneath a vehicle raised using a jack; use an axle
stand.
 Remove the cover on each of the bolts using the bolt cover removal
tool.
 Fit the security socket on the wheelbrace to slacken the security
bolt.
 Slacken the other bolts using the wheelbrace only.
 Place the jack in contact with one of the two front A or rear B
locations provided on the underbody, whichever is closest to the
wheel to be changed.
 Extend the jack until its base plate is in contact with the ground.
Ensure that the centreline of the jack base plate is directly below
the location A or B used.
 Raise the vehicle until there is sufficient space between the wheel
and the ground to admit the spare (not punctured) wheel easily.
 Remove the bolts and store them in a clean place.
 Remove the wheel.
8/ PRACTICAL INFORMATION
REMOVING THE WHEEL
170
FITTING THE WHEEL
 Put the wheel in place on the hub.
 Screw in the bolts by hand.
 Pre-tighten the security bolt using the wheelbrace fitted with the
security socket.
 Pre-tighten the other bolts using the wheelbrace only.
 Tighten the security bolt using the wheelbrace fitted with the
security socket.
 Tighten the other bolts using the wheelbrace only.
 Refit the covers on each of the bolts.
 Store the tools in the storage box.
After changing a wheel
Have the tightening of the bolts and the pressure of the new wheel
checked by a PEUGEOT dealer or a qualified workshop without
delay.
 Lower the vehicle fully.
 Fold the jack and detach it.
TOOLS AND SPARE WHEEL*
Access to the spare wheel*
Never drive with the rear seat folded when the
spare wheel - or a punctured wheel - is present
in the boot.
Warning marking
"Do not release the backrest of the rear seats!"
* According to country.
 Open the boot lid.
 Remove the spare wheel by grasping the grip of its protective
cover.
 Position the wheel vertically so as to read the warning markings.
 Remove the Velcro® located on the tyre tread.
 Detach the straps, located on each sidewall, then slacken them.
 Remove the wheel from its protective cover.
When refitting the wheel into its cover, place it so that the valve is
opposite the strap fixings.
8/ PRACTICAL INFORMATION
Depending on the country of sale, the vehicle is equipped with the tools
needed to change a wheel and may also be equipped with a spare
wheel.
The spare wheel is stowed in a protective cover, secured to the boot
floor with Velcro®.
The tools are held in a storage box under the boot floor.
172
Access to tools*
 Open the boot lid.
 Lift the boot floor using its strap.
 Fix it in the vertical position beyond the stops located on the boot
sides.
 Remove the temporary puncture repair kit for access to the jack.
All of these tools are specific to your vehicle. Do not use them for
other purposes.
* According to country.
SNOW CHAINS
In wintry conditions, snow chains improve traction as well as the
behaviour of the vehicle when braking.
Use only the chains designed to be fitted to the type of wheel fitted to
your vehicle:
Original tyre size
235/45 R18
235/40 R19
225/45 R18
Maximum link size.
cannot be fitted with chains
9 mm
For more information on snow chains, contact a PEUGEOT dealer or a
qualified workshop.
Take account of the legislation in force in your country on the use
of snow chains and the maximum running speed authorised.
Advice on installation
 If you have to fit the chains during a journey, stop the vehicle on a
flat surface on the side of the road.
 Apply the parking brake and position any wheel chocks to prevent
movement of your vehicle.
 Fit the chains following the instructions provided by the
manufacturer.
 Move off gently and drive for a few moments, without exceeding
30 mph (50 km/h).
 Stop your vehicle and check that the snow chains are correctly
tightened.
Avoid driving on roads that have been cleared of snow, to
avoid damaging your vehicle's tyres and the road surface. It is
recommended that before you leave, you practise fitting the snow
chains on a level and dry surface. If your vehicle is fitted with alloy
wheels, check that no part of the chain or its fixings is in contact
with the wheel rim.
8/ PRACTICAL INFORMATION
The snow chains must be fitted only to the front wheels. They
must never be fitted to "space-saver" type spare wheels.
CHANGING A WIPER BLADE
BEFORE REMOVING A WIPER BLADE
 Within one minute after switching off the ignition, operate the wiper
stalk to position the wiper blades in the centre of the windscreen.
REMOVING
174
 Raise the corresponding wiper arm.
 Unclip the wiper blade and remove it.
FITTING
 Put the corresponding new wiper blade in place and clip it.
 Fold down the wiper arm carefully.
AFTER FITTING A WIPER BLADE
 Switch on the ignition.
 Operate the wiper stalk again to park the wiper blades.
System which manages the duration of use of certain functions to
conserve a sufficient level of charge in the battery.
After the engine has stopped, you can still use functions such as
the audio and telematic system, windscreen wipers, dipped beam
headlamps, courtesy lamp, etc. for a maximum combined duration of
thirty minutes.
This period may be greatly reduced if the battery is not fully charged.
SWITCHING TO ECONOMY MODE
Once this time has elapsed, a message appears in the screen indicating
that the vehicle has switched to economy mode and the active functions
are put on standby.
If the telephone is being used at this time:
it will be maintained for 5 minutes with the Bluetooth system
of your PEUGEOT Connect Sound (RD5),
it will still be possible to finish the call with the PEUGEOT
Connect Navigation (RT6) or PEUGEOT Connect Media
(NG4 3D).
EXITING ECONOMY MODE
These functions are reactivated automatically next time the vehicle is
driven.
To restore operation of these functions immediately, start the engine
and let it run for at least 5 minutes.
Let the engine run for the period specified to ensure that the battery
charge is sufficient.
Do not repeatedly and continuously restart the engine in order to charge
the battery.
A flat battery prevents the engine from starting (refer to the
"Battery" section).
LOAD REDUCTION MODE
System which manages the use of certain functions according to the
level of charge remaining in the battery.
When the vehicle is being driven, the load reduction function temporarily
deactivates certain functions, such as the air conditioning, the heated
rear screen...
The deactivated functions are reactivated automatically as soon as
conditions permit.
8/ PRACTICAL INFORMATION
ENERGY ECONOMY MODE
BATTERY
STARTING USING ANOTHER BATTERY
ACCESS TO THE BATTERY
176
 Connect the red cable to the positive terminal (+) of the flat
battery A, then to the positive terminal (+) of the slave battery B.
The battery is located under the bonnet.
For access to it:
 open the bonnet using the interior release lever, then the exterior
safety catch,
 remove the plastic cover for access to the two terminals,
 wait 2 minutes after switching off the ignition before disconnecting
the battery,
 unclip the fusebox to remove the battery, if necessary.
The batteries contain harmful substances such as sulphuric
acid and lead. They must be disposed of in accordance with
regulations and must not, in any circumstances, be discarded with
household waste.
Take used remote control batteries and vehicle batteries to a
special collection point.
 Connect one end of the green or black cable to the negative
terminal (-) of the slave battery B.
 Connect the other end of the green or black cable to the earth
point C on the broken down vehicle.
 Operate the starter, let the engine run.
 Wait until the engine returns to idle and disconnect the cables.




Disconnect the battery from the vehicle.
Follow the instructions for use provided by the manufacturer of the charger.
Reconnect starting with the negative terminal (-).
Check that the terminals and connectors are clean. If they are
covered with sulphate (whitish or greenish deposit), remove them
and clean them.
DISCONNECTING / RECONNECTING THE
CABLES
To avoid discharging the battery, do not leave the vehicle lighting
on repeatedly with the ignition off (refer to the "Energy economy
mode" paragraph).
It is advisable to disconnect the battery if the vehicle is to be left
unused for more than one month.
Do not disconnect the terminals while the engine is running.
Do not charge the batteries without disconnecting the terminals first.
Before disconnecting the battery
Wait 2 minutes after switching off the ignition before disconnecting
the battery.
Retract the active spoiler then close the windows and the doors
before disconnecting the battery.
Following reconnection of the battery
 Raise the locking tab D fully.
 Position the open clip E of the cable on the positive terminal (+)
of the battery.
 Press vertically on the clip E to position it correctly against the
battery.
 Lock the clip by lowering the tab D.
Do not force the tab as locking will not be possible if the clip is not
positioned correctly.
Start the procedure again.
Following reconnection of the battery, switch on the ignition
and wait 1 minute before starting to permit initialisation of the
electronic systems. However, if slight problems remain following
this operation, contact a PEUGEOT dealer or a qualified
workshop.
Referring to the corresponding section, you must yourself
reinitialise:
the remote control key,
the electric windows and the automatic partial opening of the
door windows,
the GPS satellite navigation system.
Some functions are not available if the battery is not sufficiently
charged.
8/ PRACTICAL INFORMATION
CHARGING THE BATTERY USING A BATTERY
CHARGER
CHANGING A BULB
FRONT LAMPS
Model with halogen headlamps
The headlamps are fitted with polycarbonate glass with a
protective coating:
 do not clean them using a dry or abrasive cloth, nor with
a detergent or solvent product,
 use a sponge and soapy water or a pH neutral product,
 when using a high pressure washer on persistent marks, do
not keep the lance directed towards the lamps or their edges
for too long, so as not to damage their protective coating and
seals.
178
1.
2.
3.
4.
Changing a bulb should only be done after the headlamp has been
switched off for a few minutes (risk of serious burns).
 Do not touch the bulb directly with your fingers, use a lint-free
cloth.
It is imperative to use only anti-ultraviolet (UV) type bulbs to avoid
damaging the headlamp.
Always replace a failed bulb with a new bulb with the same type
and specification.
Direction indicators (PY21W amber).
Dipped beam headlamps (H7).
Main beam headlamps (H1).
Daytime running lamps / sidelamps (P21/5W)
or
Daytime running lamps / sidelamps (LEDs).
Changing direction indicator bulbs
1.
2.
3.
4.
 Turn the bulb holder a quarter of a turn and extract it.
 Pull the bulb out and change it.
To refit, carry out these operations in reverse order.
Direction indicators (PY21W SV silver).
Directional dipped / main beam headlamps (D1S).
Additional main beam headlamps (H1).
Daytime running lamps / sidelamps (P21/5W)
or
Daytime running lamps / sidelamps (LEDs).
Amber or silver coloured bulbs, such as the direction indicators,
must be replaced with bulbs of identical specifications and colour.
Risk of electrocution
Xenon bulbs (D1S) must be replaced by a PEUGEOT dealer or a
qualified workshop.
When refitting, close the protective cover carefully to assure the
sealing of the headlamp.
8/ PRACTICAL INFORMATION
Model with xenon and directional headlamps
Changing dipped beam headlamp bulbs
 Remove the protective cover by pulling the tab.
 Disconnect the bulb connector.
 Spread the springs to release the bulb.
 Pull the bulb out and change it.
To refit, carry out these operations in reverse order.
180
Changing main beam headlamp bulbs
 Remove the protective cover by pulling on the tab.
 Disconnect the bulb connector.
 Compress the springs to release the bulb.
 Remove the bulb and change it.
To refit, carry out these operations in reverse order.
Changing daytime running lamp / sidelamp bulbs
 Remove the protective cover by pulling on the tab.
 Disconnect the bulb connector.
 Turn the bulb holder a quarter of a turn and extract it.
 Pull the bulb and change it.
To refit, carry out these operations in reverse order.
REAR LAMPS
For the replacement of these bulbs, contact a PEUGEOT dealer or a
qualified workshop.
Changing the daytime running lamps / sidelamps
For the replacement of this type of LED lamp, contact a PEUGEOT
dealer or a qualified workshop.
1.
2.
3.
4.
5.
Sidelamps (LEDs).
Direction indicators (LEDs).
Brake lamps / sidelamps (P21/5W).
Reversing lamps (P21W).
Foglamp (P21W).
8/ PRACTICAL INFORMATION
Changing integrated direction indicator side repeaters
Changing brake lamps / sidelamps
This bulb is changed from outside the boot, having first removed the
rear lamp:
 open the boot lid,
 unclip the access flap of the corresponding side trim, then remove it,
182
 disconnect the lamp connector,
 remove the two lamp fixing bolts,
 unclip the lamp taking hold of it at the base, then tilt it,
 turn the bulb holder one quarter of a turn and remove it,
 turn the bulb one quarter of a turn and change it.
To refit, carry out these operations in reverse order.
Changing reversing lamps and foglamps
 turn these two bolts one quarter of a turn and remove them,
 push the lamp towards the inside to unclip it, then tilt it,
 pull the lamp towards the outside for access to the various
bulb-holders.
- For the reversing lamps: pull the corresponding bulb holder,
- turn the bulb one quarter of a turn and change it.
- For the foglamp: turn the bulb holder one quarter of a turn and
remove it,
- turn the bulb one quarter of a turn and change it.
To refit, carry out these operations in reverse order.
On the left-hand side, take care not to touch the silencer; risk
of burns, if you change the bulb immediately after switching
off the ignition.
8/ PRACTICAL INFORMATION
These two bulbs are changed from outside the rear bumper:
 unclip the protective cover from the rear, then tilt it,
 remove it completely to gain access to the two lamp fixing bolts,
Changing reversing lamp and foglamp bulbs
(1.6 litre THP 270 hp version)
184
The bulbs on these two types of lamp are changed by partly removing
the lamp unit A in the rear bumper:
 using a screwdriver, remove the 3 fixing screws B located under the
vehicle,
 without forcing, lower the rear part of the lamp unit for access to the
bulb holders C,
 turn the corresponding bulb holder a quarter of a turn then remove
it towards the front of the vehicle,
 turn the bulb one quarter of a turn and change it.
To refit, carry out these operations in reverse order.
Take care not to touch the silencer; risk of burns, if you
change the bulb immediately after switching off the ignition.
Changing sidelamps and direction indicators
For the replacement of this type of LED lamp, contact a PEUGEOT
dealer or a qualified workshop.
Changing the third brake lamp (LEDs)
Changing number plate lamps (W5W)
 Insert the end of the vehicle's key in the hole in the transparent
cover.
 Push towards the outside to unclip it.
 Remove the transparent cover.
 Pull the bulb out and change it.
High pressure washing
When using this type of washing on stubborn dirt, do not persist
on the headlamps, the lamps and their surrounds to avoid
damaging their protective coating and seals.
8/ PRACTICAL INFORMATION
For the replacement of this type of LED lamp, contact a PEUGEOT
dealer or a qualified workshop.
CHANGING A FUSE
186
ACCESS TO THE TOOLS
The extraction tweezer is fitted to the back of the dashboard fusebox
cover.
To gain access to them:
 turn the screw a quarter of a turn to the left,
 unclip the cover by pulling at the top right,
 remove the cover completely and turn it over,
 remove the carrier on which is fitted the tweezer.
CHANGING A FUSE
Before changing a fuse, tit is necessary to:
 identify the cause and correct it,
 switch off all electrical consumers,
 immobilise the vehicle and switch off the ignition,
 identify the failed fuse using the allocation tables and drawings
presented on the following pages.
To replace a fuse, you must:
use the special tweezer to extract the fuse from its housing and
check the condition of its filament,
always replace a failed fuse with a fuse of the same rating (same
colour); a different rating fuse may cause malfunctions (risk of fire).
If the fault recurs soon after changing a fuse, have the electrical
system of your vehicle checked by a PEUGEOT dealer or a
qualified workshop.
Good
Failed
Tweezer
Installing electrical accessories
PEUGEOT will not accept responsibility for the cost incurred in
repairing your vehicle or for rectifying malfunctions resulting from
the installation of accessories not supplied and not recommended
by PEUGEOT and not installed in accordance with its instructions,
in particular when the combined consumption of all of the
additional equipment connected exceeds 10 milliamperes.
8/ PRACTICAL INFORMATION
Your vehicle's electrical system is designed to operate with
standard or optional equipment.
Before installing other electrical equipment or accessories on your
vehicle, contact a PEUGEOT dealer or a qualified workshop.
DASHBOARD FUSES
Fuse tables
188
The fusebox is placed in the lower section of the dashboard (left-hand
side). It consists of two boxes.
Access to the fuses
Fuse N°
Rating
F2
30 A
Locking and deadlocking earth.
F3
5A
Airbags, active bonnet and pretensioners
control unit.
F4
10 A
Clutch pedal switch, electrochromatic
rear view mirror, automatic gearbox,
switching and protection unit.
F5
30 A
One-touch electric windows, folding door
mirrors supply.
F7
5A
Front and rear courtesy lamps, map
reading lamps, sun visor lighting, glove
box lighting.
F8
20 A
Audio equipment, audio/telephone,
multifunction screen, tyre under-inflation
detection, clock.
F9
30 A
12 V socket.
F10
15 A
Steering mounted controls.
F11
15 A
Low current ignition switch.
F12
15 A
Instrument panel, air conditioning,
driver's seat memory unit, rain /
sunshine sensor, airbags.
 Refer to the paragraph "Access to the tools".
Box 1
Functions
Rating
Functions
F13
5A
Engine fusebox, active bonnet.
F14
15 A
Multifunction screen, seat belt and
passenger's front airbag warning lamps
display, instrument panel screen,
amplifier, Bluetooth system, parking
sensors control unit, USB Box.
F15
30 A
Locking and deadlocking.
F17
40 A
Rear screen and door mirrors demist/
defrost.
Fuse N°
Rating
G36
30 A
Hi-Fi amplifier.
G37
30 A
Passenger's seat memory unit.
G38
30 A
Driver's seat memory unit.
G39
5A
Lighting memory unit.
G40
30 A
Driver and passenger heated seats.
Functions
8/ PRACTICAL INFORMATION
Box 2
Fuse N°
ENGINE COMPARTMENT FUSES
190
The fusebox is placed in the engine compartment near the battery
(left-hand side).
Access to the fuses
 Unclip the cover.
 Change the fuse (see corresponding paragraph).
 When you have finished, close the cover carefully to assure the
sealing of the fusebox.
Fuse table
Fuse N°
Rating
Functions
F2
15 A
Horn.
F3
10 A
Front wash-wipe.
F4
20 A
Daytime running lamps.
F5
15 A
Air flow sensor, coolant pump, oil pump,
thermostat, blow-by heater (petrol),
by-pass and EGR electrovalves (Diesel),
diesel heater (Diesel).
F6
10 A
Steering wheel angle sensor, ABS/DSC
control unit, DSC sensor.
F7
10 A
Power steering control unit, automatic
gearbox, dual function brake switch.
F8
25 A
Starter motor control.
F9
10 A
Diagnostic socket, directional
headlamps, particle emission filter pump
(Diesel).
F11
40 A
Air conditioning blower.
Rating
Functions
F12
40 A
Windscreen wipers slow / fast speed.
F15
10 A
Right-hand main beam headlamp.
F16
10 A
Left-hand main beam headlamp.
F17
15 A
Left-hand dipped headlamp.
F18
15 A
Right-hand dipped headlamp.
8/ PRACTICAL INFORMATION
Fuse N°
192
Table of fuses over the battery
Fuse N°
Rating
Functions
F2
5A
Dual function brake switch.
F3
5A
Battery charge unit.
F4
25 A
ABS/ESC electrovalves.
F6
15 A
Automatic gearbox.
All work on the other types of fuses (midi-fuses and maxi-fuses)
must be carried out only by a PEUGEOT dealer or a qualified
workshop.
TOWING A VEHICLE
This is stored in the boot under the floor.
For access to it:
 open the boot,
 raise the floor using the strap,
 secure it in the vertical position beyond the stops, located on the
sides of the boot,
 remove the towing eye from the storage box.
GENERAL RECOMMENDATIONS
Observe the legislation in force in your country.
Ensure that the weight of the towing vehicle is higher than that of
the towed vehicle.
The driver must remain at the wheel of the towed vehicle and
must have a valid driving licence.
When towing a vehicle with all four wheels on the ground, always
use an approved towing bar; rope and straps are prohibited.
The towing vehicle must move off gently.
When towing a vehicle with the engine off, there is no longer any
power assistance for braking or steering.
In the following cases, you must always call on a professional
recovery service:
vehicle broken down on a motorway or fast road,
four-wheel drive vehicle,
when it is not possible to put the gearbox into neutral, unlock
the steering, or release the parking brake,
towing with only two wheels on the ground,
where there is no approved towing bar available...
8/ PRACTICAL INFORMATION
TOWING EYE
194
TOWING YOUR VEHICLE
Towing from the rear
Towing from the front
It is also possible to pull your vehicle from the rear, but only in
exceptional circumstances (vehicle in a parking space, off the road...).
 On the rear bumper, unclip the cover by pressing on the left.
 Screw the towing eye in fully.
 Install the towing bar.
 Place the gear lever in neutral (position N for an automatic
gearbox).
 Switch on the hazard warning lamps on both vehicles.
 Move off very gently to pull the vehicle out.
 On the front bumper, unclip the cover by pressing on the left.
 Screw the towing eye in fully.
 Install the towing bar.
 Place the gear lever in neutral (position N for an automatic
gearbox).
Failure to observe this instruction could result in damage
to certain components (braking, transmission...) and the
absence of braking assistance the next time the engine is
started.
 Unlock the steering by turning the ignition key one notch and
release the parking brake.
 Switch on the hazard warning lamps on both vehicles.
 Move off gently and drive slowly and for a short distance only.
TOWING ANOTHER VEHICLE*





On the rear bumper, unclip the cover by pressing on the left.
Screw the towing eye in fully.
Install the towing bar.
Switch on the hazard warning lamps on both vehicles.
Move off gently and drive slowly and for a short distance only.
* Except 1.6 litre THP 270 hp version.
TOWING A TRAILER
Towbar suitable for the attachment of a trailer with additional lighting
and signalling.
DRIVING ADVICE
Driving with a trailer subjects the towing vehicle to more significant
stress and its driver must be particularly careful.
 Distribute the load in the trailer so that the heaviest items are as
close as possible to the axle and the nose weight approaches the
maximum permitted without exceeding it.
Air density decreases with altitude, thus reducing engine performance.
Above 1 000 metres, the maximum towing load must be reduced by
10 % and so on for every 1 000 metres of altitude.
Refer to the "Technical data" section for details of the weights and
towing loads which apply to your vehicle version.
Your vehicle is primarily designed for transporting people and luggage,
but it may also be used for towing a trailer.
We recommend use of the PEUGEOT genuine towbar with ball
which can be removed without tools and its harness that have
been tested and approved from the design stage of your vehicle,
and that the fitting of the towbar is entrusted to a PEUGEOT
dealer or a qualified workshop.
If the trailer is fitted outside the PEUGEOT dealer network, it must
be fitted in accordance with the manufacturer's instructions.
Side wind
 Take into account the increased sensitivity to side wind.
8/ PRACTICAL INFORMATION
Distribution of loads
Cooling
Towing a trailer on a slope increases the temperature of the coolant.
As the fan is electrically controlled, its cooling capacity is not dependent
on the engine speed.
 To lower the engine speed, reduce your speed.
The maximum towing load on a long slope depends on the gradient and
the ambient temperature.
In all cases, pay attention to the coolant temperature.
196
 If the warning lamp and the STOP warning lamp come
on, stop the vehicle and switch off the engine as soon as
possible.
Braking
Towing a trailer increases the braking distance.
Tyres
 Check the tyre pressures of the towing vehicle and of the trailer,
observing the recommended pressures.
Lighting
 Check the electrical signalling on the trailer.
The rear parking sensors will be deactivated automatically if a
genuine PEUGEOT towbar is used.
When not towing a trailer, remove the quickly-detachable tow ball
before driving, so as to avoid masking the central rear lamp.
The general recommendations on cleaning and maintaining your vehicle
are given in the servicing and warranty booklet.
PEUGEOT TECHNO TEP
To clean this trim, do not use solvents or detergents with a dry cloth.
First remove dust, then use a soft cloth and soapy water. Dry with
another soft cloth.
HEADLAMPS AND LAMPS
The headlamps have polycarbonate lenses, finished with a protective
lacquer.
Do not clean them with a dry or abrasive cloth, nor with detergent or
solvent products.
Use a sponge and soapy water.
The use of a high pressure jet wash for cleaning the headlamps,
lamps and their surrounds may damage the lacquer and seals.
Observe the recommendations on pressure and distance for jet
washing.
First clean persistent stains with a sponge and warm soapy water.
ALUMINIUM ARCHES
To clean these arches, do not use a dry cloth with an abrasive product.
Use a sponge and soapy water.
CUSTOMISING STICKERS
These customising parts are self-adhesive stickers, treated to give good
resistance to ageing and tearing.
They are intended for customising the body.
Available also as accessories, we recommend that you have them fitted
by a PEUGEOT dealer or a qualified workshop.
When washing your vehicle, keep the end of a high-pressure
lance at least 30 centimetres from the stickers.
8/ PRACTICAL INFORMATION
CLEANING AND MAINTENANCE
MATT PAINT
198
If you vehicle is finished with a clear matt lacquer, please observe the
following recommendations to avoid damaging the paintwork by the use
of an inappropriate cleaning procedures.
These recommendations are also valid for alloy road wheels finished
with clear matt lacquer.
Never clean the vehicle without water.
Never wash your vehicle in an automatic roller brush car wash.
Never polish the vehicle body, nor the alloy wheels. Doing this will
make the paintwork shiny.
Do not use paint cleaners, abrasive products or paint polishing or
preserving products (such as wax, for example) on the paintwork.
These products are only suitable for bright finishes. Application of
these products on vehicles with a matt finish will seriously damage
the paint surface of the vehicle, giving rise to irreversible shiny or
stained areas.
Never use a high pressure jet wash with a lance fitted with a
brush, this may scratch the paintwork.
Never select a wash programme that finishes with a hot wax
cycle.
We recommend the use of a high pressure jet wash, or at least a
water hose with a high output.
We recommend that the vehicle be rinsed using de-ionised water.
Use only a microfibre cloth to dry the vehicle. It must be clean and
used without heavy pressure.
Lightly wipe off any fuel stains present on the bodywork using a
soft cloth, then leave to dry.
From the range of cleaning and maintenance products in the
"TECHNATURE" range recommended and approved by PEUGEOT,
use only the insect remover and car shampoo, which are the only
products to be used on the bodywork.
The insect remover can also be used to remove minor marks
(for example: finger marks...).
Always have paint repairs done by a PEUGEOT dealer or a qualified
workshop.
ACCESSORIES
A wide range of accessories and genuine parts is available from the
PEUGEOT dealer network.
These accessories and parts have been tested and approved for
reliability and safety.
They are all adapted to your vehicle and benefit from PEUGEOT's
recommendation and warranty.
"Style":
"Comfort":
"Safety and security":
front parking sensors, cool box...
anti-theft alarm, window etching, wheel security bolts, breathalyser, first
aid kit, fire extinguisher, warning triangle, high visibility jacket, booster
cushions and child seats, stolen vehicle tracking system, snow chains,
anti-skid tyre covers...
"Transport solutions":
"Protection":
boot tray, boot spacers, towbar bicycle carrier, towbar with quickly
detachable ball, towbar harnesses...
boot liner, mats*, bumper protective strips, vehicle protective cover...
*
To avoid any risk of jamming of the pedals:
- ensure that the mat is positioned and secured correctly,
- never fit one mat on top of another.
8/ PRACTICAL INFORMATION
When fitting a trailer towbar and its harness outside the
PEUGEOT dealer network, this must be done following the
manufacturer's recommendations.
leather and alcantara sport steering wheel, alcantara gear lever gaiter,
alloy wheels, door mirror shells in carbon fibre...
"Multimedia":
portable navigation systems, Wi-Fi on Board...
By going to a PEUGEOT dealer you can also obtain products for
cleaning and maintenance (exterior and interior) - including ecological
products from the "TECHNATURE" range, topping up products
(screenwash, ...), touch-up pens and aerosols for the exact colour of
your vehicle, refills (cartridge for temporary tyre repair kit...), ...
Installation of radio communication transmitters
Depending on the legislation in force in the country, certain
safety equipment may be compulsory: high visibility safety vests,
warning triangles, breathalyzers, spare bulbs, spare fuses, a fire
extinguisher, a first aid kit, mud flaps at the rear of the vehicle.
200
Before installing any after-market radio communication transmitter,
you can contact a PEUGEOT dealer for the specification of
transmitters which can be fitted (frequency, maximum power,
aerial position, specific installation requirements), in line with the
Vehicle Electromagnetic Compatibility Directive (2004/104/EC).
The fitting of electrical equipment or accessories which are not
recommended by PEUGEOT may result in a failure of your
vehicle's electronic system and excessive electrical consumption.
Please note this precaution. You are advised to contact a
PEUGEOT representative to be shown the range of recommended
equipment and accessories.
Engines
1.6 litre THP
150 hp
1.6 litre THP 156 hp
1.6 litre THP
163 hp
1.6 litre THP
200 hp
1.6 litre THP
270 hp
Automatic
(6-speed)
Manual
(6-speed)
Automatic
(6-speed)
Automatic
(6-speed)
Manual
(6-speed)
Manual
(6-speed)
Model codes:
4J...
5FE-J
5FV-8
5FV-A
5FM-J
5FU-8
5FGM
Cubic capacity (cc)
1 598
1 598
1 598
1 598
1 598
Bore x stroke (mm)
77 x 85.8
77 x 85.8
77 x 85.8
77 x 85.8
77 x 85.8
Max power: EU standard (kW)*
110
115
120
147
199
Max power engine speed (rpm)
6 050
6 000
6 000
5 500
6 000
Max torque: EU standard (Nm)
240
240
240
275
330
Max torque engine speed (rpm)
1 400
1 400
1 400
1 700
1 900
Unleaded
Unleaded
Unleaded
Unleaded
Unleaded
Catalytic converter
Yes
Yes
Yes
Yes
Yes
Engine oil capacity (in litres)
(with filter replacement)
4.25
4.25
4.25
4.25
-
Gearboxes
Fuel
* The maximum power quoted is the type approved value obtained on a test bed, under the conditions defined in European legislation
(directive 1999/99/CE).
9/ TECHNICAL DATA
PETROL ENGINES AND GEARBOXES
PETROL WEIGHTS AND TOWED LOADS (IN KG)
Engines
Gearboxes
1.6 litre THP
150 hp
1.6 litre THP 156 hp
1.6 litre THP
163 hp
1.6 litre THP
200 hp
1.6 litre THP
270 hp
Automatic
Manual
Auto.
Automatic
Manual
Manual
Model codes: 4J...
5FE-J
5FV-8
5FV-A
5FM-J
5FU-8
5FGM
- Unladen weight
1 297
1 275
1 297
1 297
1 297
1 280
- Kerb weight
1 372
1 350
1 372
1 372
1 372
1 355
463
465
463
463
483
425
1 760
1 740
1 760
1 760
1 780
1 780
2 260
2 240
2 260
2 260
2 280
1 780
500
500
500
500
500
0
- Braked trailer* (with load transfer within
GTW limit)
650
650
650
650
650
0
- Unbraked trailer
500
500
500
500
500
0
- Recommended nose weight
65
65
65
65
65
0
- Payload
- Gross vehicle weight (GVW)
202
- Gross train weight (GVW)
on a 12% gradient
- Braked trailer (within GTW limit)
on a 10% or 12% gradient
* The weight of the braked trailer can be increased, within the GTW limit, on condition that the GVW of the towing vehicle is reduced by the same
amount; warning: towing with a lightly loaded towing vehicle may have an adverse effect on its road holding.
The GTW and towed load values indicated apply up to a maximum altitude of 1000 metres; the towed load mentioned must be reduced by 10 % for
every additional 1000 metres.
The speed of a towing vehicle must not exceed 60 mph (100 km/h) (comply with the legislation in force in your country).
High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; when the ambient temperature is
higher than 37 °C, limit the towed weight.
DIESEL ENGINE AND GEARBOX
Gearbox
2.0 litre HDi 163 hp
Manual
(6-speed)
Model codes:
4J...
RHH-8
Cubic capacity (cc)
1 997
Bore x stroke (mm)
85 x 88
Max power: EU standard (kW)*
120
Max power engine speed (rpm)
3 750
Max torque: EU standard (Nm)
340
Max torque engine speed (rpm)
2 000
Fuel
Diesel
Catalytic converter
Yes
Particle emission filter
Yes
Engine oil capacity (in litres)
(with filter replacement)
-
* The maximum power quoted is the type approved value obtained on a test bed, under the conditions defined in European legislation
(directive 1999/99/CE).
9/ TECHNICAL DATA
Engine
DIESEL WEIGHTS AND TOWED LOADS (IN KG)
Diesel engine
Gearbox
Manual
Model codes: 4J...
RHH-8
- Unladen weight
1 370
- Kerb weight
1 445
- Payload
- Gross vehicle weight (GVW)
204
2.0 litre HDi 163 hp
455
1 825
- Gross train weight (GTW)
on a 12% gradient
2 325
- Braked trailer (within GTW limit)
on a 10% or 12% gradient
500
- Braked trailer* (with load transfer within GTW limit)
650
- Unbraked trailer
500
- Recommended nose weight
65
* The weight of the braked trailer can be increased, within the GTW limit, on condition that the GVW of the towing vehicle is reduced by the same
amount; warning: towing with a lightly loaded towing vehicle may have an adverse effect on its road holding.
The GTW and towed load values indicated apply up to a maximum altitude of 1000 metres; the towed load mentioned must be reduced by 10 % for
every additional 1000 metres.
The speed of a towing vehicle must not exceed 60 mph (100 km/h) (comply with the legislation in force in your country).
High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; when the ambient temperature is
higher than 37 °C, limit the towed weight.
* 1.6 litre THP 270 hp version
9/ TECHNICAL DATA
DIMENSIONS (IN MM)
IDENTIFICATION MARKINGS
Various visible markings for the identification of your vehicle.
A. Vehicle identification number (VIN) under the bonnet.
This number is engraved on the bodywork near the damper
support.
For access to it, raise the plastic cover.
D. Tyre/paint label.
This label is affixed to the door aperture, on the driver's side.
It bears the following information:
the tyre inflation pressures, laden and unladen,
the tyre sizes,
the inflation pressure of the spare wheel,
the paint colour code.
206
B. VIN on the windscreen lower cross member.
This number is indicated on a self-adhesive label which is visible
through the windscreen.
C. Manufacturer's label.
The number is indicated on a self-destroying label affixed to the
door aperture, below the door striker, on the right-hand side.
This label also indicates the unladen weight, the gross vehicle
weight (GVW) and the gross train weight (GVW).
The tyre pressures must be checked when the tyres are cold, at
least once a month.
If the tyre pressures are too low, this increases fuel consumption.
EMERGENCY OR ASSISTANCE CALL
207
EMERGENCY OR ASSISTANCE CALL
PEUGEOT Connect SOS
In an emergency, press this button for more than
2 seconds. Flashing of the green LED and a voice
message confirm that the call has been made to the
"PEUGEOT Connect SOS" centre*.
The green LED remains on (without flashing) when communication is
established. It goes off at the end of communication.
Pressing this button again immediately cancels the request. The green
LED goes off. Cancellation is confirmed by a voice message.
To cancel a call, tell the "PEUGEOT Connect SOS" call centre that the call
was a mistake.
"PEUGEOT Connect SOS" immediately locates your vehicle, starts
communication with you in your language**, and where necessary sends
the appropriate public emergency services**. In countries where the
service is not available, or when the locating service has been expressly
declined, the call sent directly to the emergency services (112) without the
vehicle location.
If an impact is detected by the airbag control unit, and
independently of the deployment of any airbags, an emergency call
is made automatically.
* Subject to the general conditions for the service available from dealers
and to technological and technical limitations.
** Depending on the geographical cover of "PEUGEOT Connect SOS",
"PEUGEOT Connect Assistance" and the official national language
selected by the owner of the vehicle.
The list of countries covered and PEUGEOT CONNECT services
services is available from dealers or at www.peugeot.co.uk.
208
PEUGEOT Connect Assistance
Press this button for more than 2 seconds to request
assistance if the vehicle breaks down.
A voice message confirms that the call has been made**.
Pressing this button again immediately cancels the request.
The cancellation is confirmed by a voice message.
Operation of the system
When the ignition is switched on, the green
LED comes on for 3 seconds indicating that
the system is operating correctly.
If the orange LED flashes: there is a system
fault.
If the orange LED is on continuously: the
backup battery must be replaced.
In either case, contact a PEUGEOT dealer.
If you purchased your vehicle outside the PEUGEOT dealer network,
we invite you to have a dealer check the configuration of these services
and, if desired, modified to suit your wishes. In a multi-lingual country,
configuration is possible in the official national language of your choice.
For technical reasons and in particular to improve the quality of
"PEUGEOT CONNECT services" services to customers, the manufacturer
reserves the right to carry out updates to the vehicle's on-board telematic
system.
EMERGENCY OR ASSISTANCE CALL USING
PEUGEOT Connect Media Navigation (NG4 3D)
PEUGEOT Connect SOS
Warning - the emergency call and the services are only active
if the internal telephone is used with a valid SIM card. With a
Bluetooth telephone and without a SIM card, these services are not
operational.
In an emergency, press the SOS button until an audible
signal is heard and a "Confirmation / Cancellation"
screen is displayed (if valid SIM card inserted).
A call is made to the PEUGEOT Emergency team
which receives locating information from the vehicle
and can send a detailed alert to the relevant emergency
services.
In countries in which the team is not operational, or
when the locating service has been expressly declined,
the call is sent to the emergency services (112).
PEUGEOT Connect Assistance
Press this button for access to PEUGEOT services.
Select "Customer call" to request
any information about the PEUGEOT
marque.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Customer call
Select "PEUGEOT Assistance"
to make a roadside assistance call.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
PEUGEOT Assistance
If an impact is detected by the airbag control unit, and independently
of the deployment of any airbags, an emergency call is made
automatically.
The message "Deteriorated emergency call" associated with
flashing of the orange indicator lamp indicates a malfunction.
Contact a PEUGEOT dealer.
This service is subject to conditions and availability. Consult a
PEUGEOT dealer. If you have purchased your vehicle outside the
PEUGEOT dealer network, we invite you to have a dealer check
the configuration of these services and, if desired, modified to suit
your wishes.
209
210
PEUGEOT Connect Media Navigation
(NG4 3D)
MULTIMEDIA AUDIO SYSTEM / BLUETOOTH TELEPHONE
GPS EUROPE
CONTENTS
The system is protected in such a way that it will only
operate in your vehicle.
For safety reasons, the driver must only carry out
operations which require prolonged attention while the
vehicle is stationary.
When the engine is switched off and to prevent
discharging of the battery, the system switches off
following the activation of the energy economy mode.
01 First steps
02 Voice commands and
steering mounted controls
03 General operation
04 Navigation - Guidance
05 Traffic information
06 Radio
07 Music media players
08 Using the telephone
09 Screen menu map
Frequently asked questions
p.
p.
212
214
p.
p.
p.
p.
p.
p.
p.
p.
217
222
231
233
234
239
244
249
211
STEPS
01 FIRST
PEUGEOT Connect Media Navigation (NG4 3D) control panel
Access to the Media Menu
(audio CD, Jukebox,
Auxiliary input).
Display the list of tracks.
Change the audio source.
Access to the Navigation
Menu and display recent
destinations.
Abandon the current
operation.
Long press: return to main
display.
Access to the Traffic Menu.
Access to the Radio Menu
Display the list of stations in
alphabetical order (FM band) or
frequency order (AM band).
Access to the "SETUP" menu
(configuration).
Long press: GPS coverage.
Audio settings (Balance /
Fader, Bass / Treble, Musical
ambience...).
Enter the numbers or letters
using the alpha-numeric keypad.
Presetting 10 radio frequencies.
Adjust volume (each source
is independent, including
navigation messages and alerts).
Long press: reinitialise the
system.
Short press: mute.
Automatic search down/up for
radio frequencies.
Select previous/next CD or MP3
track.
212
Access to the Address book
Menu.
SD card reader.
Short press: clears the last
character.
STEPS
01 FIRST
PEUGEOT Connect Media Navigation (NG4 3D) navigator
Press to left / right:
With display of the "RADIO" screen:
select the previous / next frequency.
With display of the "MEDIA" screen:
select the previous / next track.
With display of the "MAP" or "NAV":
horizontal movement on the map.
Select successive display in the
screen of "MAP" / "NAV"
(if navigation in progress) /
"TEL" (if a call is in progress) /
"RADIO" or "MEDIA" being played.
CALL: access to the Phone
menu.
Bluetooth connection, accept
an incoming call.
Rotate the dial:
With display of the "RADIO" screen:
select the previous / next radio station
in the list.
With display of the "MEDIA" screen:
select the previous / next CD or MP3
track.
With display of the "MAP" or "NAV":
zoom the map in/out.
Movement of the menu selection
cursor.
Press up / down:
With display of the "RADIO" screen:
select the previous / next radio station
in the list.
With display of the "MEDIA" screen:
select the MP3 folder.
With display of the "MAP" or "NAV":
vertical movement on the map.
Go the the next or previous page in a
menu.
Movement on the virtual keypad
displayed.
OK: confirm the highlighted item.
Normal display or black screen.
END CALL: access to the
Phone menu.
End a call in progress or reject
an incoming call, Bluetooth
connection.
213
02 VOICE COMMANDS AND STEERING MOUNTED CONTROLS
CONTEXT
Initiation of voice commands
Voice recognition
Press the SETUP button and select
the "Language & Speech" function.
Turn the ring and select "Voice control".
Activate voice recognition.
Select "Tutorial".
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
Help address book
Help voice control
Help media
Help navigation
Help telephone
Help radio
Cancel
Correction
Access to the address book help
Access to the voice recognition help
Access to the media management help
Access to the guidance, navigation help
Access to the telephone help
Access to the radio help
To cancel a voice command which is in
progress
Request to correct the last voice recognition
carried out
Clear
RADIO
Select station
Station <tts:stationName>
Read out station list
Enter frequency
Select wave band
AM
FM
TA on
TA off
Select a radio station
Select a radio station using its RDS
description <tts:station Name> from the
RADIO list
Listen to the list of stations available
Listen to the frequency of the current radio
station
Choose the frequency waveband (AM or FM)
Change the frequency waveband to AM
Change the frequency waveband to FM
Activate Traffic Info (TA)
Deactivate Traffic Info
NAVIGATION
Destination input
Voice advice off
Voice advice on
Save address
Start guidance
Abort guidance
Navigate entry
POI Search
Command to enter a new destination
address
Deactivate the spoken guidance instructions
Activate the spoken guidance instructions
Save an address in the address book
Start guidance (once the address has been
entered)
Stop the guidance
Start guidance to an entry in the address
book
Start guidance to a point of interest
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
The phrases to be spoken according to the context are indicated in
the tables below.
Speak and PEUGEOT Connect Media Navigation (NG4 3D) acts.
Pressing the end of the lighting
control stalk activates voice
recognition.
214
ACTION
GENERAL
Before using the system for the first time, you are advised to listen
to, say and practice the tutorial.
SETUP
SAY
02 VOICE COMMANDS AND STEERING MOUNTED CONTROLS
Initiation of voice commands
Voice recognition
CONTEXT
MEDIA
TELEPHONE
ADDRESS
BOOK
SAY
ACTION
Media
Select the MEDIA source
Select media
Choose a source
Single slot
Select the CD player source
Jukebox
Select the Jukebox source
USB
Select the USB player source
External device
Select the audio AUX input source
SD-Card
Select the SD card source
Track <1 - 1000>
Folder <1 - 1000>
Select a specific track (number between 1
and 1 000) on the active MEDIUM
Phone menu
Open the Telephone Menu
Enter number
Enter a telephone number to be called
Phone book
Open the phone book
Dial
Make a call
Save number
Save a number in the phone book
Accept
Accept an incoming call
Reject
Reject an incoming call
Address book menu
Open the address book
Call <entry>
Call file using its <file> description as
described in the address book
Navigate <entry>
Select a Folder (number between 1 and
1 000) on the active MEDIUM
Start guidance to an address in the address
book using its <file> description
215
02 VOICE COMMANDS AND STEERING MOUNTED CONTROLS
Steering mounted controls
Wiper stalk: display "RADIO" and "MEDIA".
Lighting stalk: activate voice commands with a short press; indication of the
current navigation instruction with a long press.
Radio: automatic search for a higher frequency.
Radio: select the previous/next pre-set
CD / SD CARD / JUKEBOX: select the next track.
station.
CD / SD CARD / JUKEBOX: continuous press: fast
CD audio: select the previous/next track
forwards.
If "MEDIA" is displayed in the screen:
MP3 CD / SD CARD / JUKEBOX: select the
previous/next folder.
Select the previous/next item in the contacts list.
Volume increase.
Change audio source.
Start a call from the contacts list.
Call/hang up the telephone.
Confirm a selection.
Press for more than 2 seconds:
telephone menu.
Volume decrease.
Radio: automatic search for a lower frequency.
CD / SD CARD / JUKEBOX: select the previous track.
CD / SD CARD / JUKEBOX: continuous press: fast
backwards.
216
Mute: press the volume
increase and decrease
buttons simultaneously.
The sound is restored
by pressing one of the
two volume buttons.
03 GENERAL OPERATION
Contextual display
Press the MODE button several times in succession to gain access to the following displays:
RADIO / MUSIC MEDIA / VIDEO
FULL SCREEN MAP
TELEPHONE
(If a conversation is in progress)
NAVIGATION (If guidance is in
progress)
TRAFFIC
SETUP
SETUP:
access to the "SETUP" Menu: system language*
and voice functions*, voice initialisation (section 09),
date and time*, display, unit and system parameters.
* Available according to model.
Long press: access to the GPS coverage and to the demonstration
mode.
For maintenance of the screen, the use of a soft, non-abrasive cloth
(spectacles cloth) is recommended, without any additional product.
MEDIA
TRAFFIC:
access to the Traffic Menu: display of the current
traffic alerts.
MEDIA:
"DVD-audio" menu
"DVD-Video" menu
For a detailed global view of the menus available, refer to the
"Screen menu map" section of this handbook.
217
03 GENERAL OPERATION
Contextual display
Pressing OK gives access to short-cut
menus according to the display on the
screen.
3
NAVIGATION (IF GUIDANCE IS IN PROGRESS):
1
1
1
2
2
2
2
2
2
1
2
218
Trip info
2
3
Abort guidance
3
Repeat advice
3
Block road
2
Unblock
2
More
1
Less
1
2
Zoom/Scroll
2
Browse route
2
Route info
2
Show destination
Route type
1
Avoid
1
Satellites
1
Stopovers
1
End call
Hold call
Dial
DTMF-Tones
Private mode
Browse route
1
Zoom/Scroll
1
Voice advice
MUSIC MEDIA PLAYERS:
Route options
Calculate
TELEPHONE:
Route type
Micro off
TA
1
Play options
1
Route dynamics
2
Avoidance criteria
2
Recalculate
2
1
Normal order
Random track
Scan
Select media
03 GENERAL OPERATION
Contextual display
RADIO:
In FM mode
1
2
2
2
2
2
TA
RDS
Radiotext
FULL SCREEN MAP:
Abort guidance / Resume guidance
1
Set destination / Add stopover
1
2
2
2
Options
2
AM
3
3
TA
3
Refresh AM list
FM
Heading Up
Zoom/Scroll
1
Position info
1
In AM mode
1
2
North Up
POIs nearby
1
Regional prog.
2
3
Navigate to
AUDIO DVD (LONG PRESS):
Stop
1
Dial
Save position
3
Zoom/Scroll
2
2
2
2D Map
2.5D Map
Group 1 .2/n
Play options
2
Map Settings
1
Group
2
3
Normal order / Random track / Scan
TA
1
2
Select media
3D Map
219
03 GENERAL OPERATION
Contextual display
VIDEO DVD (LONG PRESS):
Play
1
Stop
2
DVD menus
2
3
3
3
3
DVD top menu
List of titles
List of chapters
DVD Options
2
3
3
3
220
DVD menu
Audio
Subtitles
Angle
Examples:
PEUGEOT Connect Media IS:
-
the map setting which allows the map to be displayed flat, in perspective or in 3D.
Flat map
Map in perspective
Map in 3D
-
configuration of the system by means of voice commands.
221
04 NAVIGATION - GUIDANCE
The "NAVIGATION" voice commands are listed in section 02.
During guidance, a long press on the end of the lighting stalk repeats the
last guidance instruction.
Selecting a destination
RADIO
NAV
MEDIA
NAV
TRAFFIC
Press the NAV button.
ADDR
BOOK
1
4
SETUP
2
ABC
5
3
DEF
6
GHI
JKL
MNO
7
8
9
PQRS
TUV
WXYZ
*
0
#
Select the "Address input" function
and press OK to confirm.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Address input
Once the country has been selected,
turn the ring and select the town
function. Press OK to confirm.
The list of the last 20 destinations appears under the Navigation
Menu function.
Press the NAV button again or select
the Navigation Menu function and
press OK to confirm.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Select the letters of the town one
by one confirming each time by
pressing OK.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
RADIO
MEDIA
NAV
TRAFFIC
SETUP
2
ABC
5
JKL
8
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
Destination input
222
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
6
MNO
9
TUV
WXYZ
*
0
#
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Navigation Menu
Select the "Destination input"
function and press OK to confirm.
3
DEF
PQRS
A pre-set list (by entering the first few letters) of the towns in the
country selected can be accessed via the LIST button on the virtual
keypad.
04 NAVIGATION - GUIDANCE
It is possible to scroll the map using the 4-direction navigator. It is possible
to select its orientation via the short-cut menu of the "Full screen map".
Press OK then select "Map Settings" and confirm.
RADIO
Turn the ring and select OK.
Press OK to confirm.
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
6
9
TUV
WXYZ
*
0
#
To delete a destination; from steps 1 to 3, select "Choose from last
destinations".
A long press on one of the destinations displays a list of actions
from which you can select:
Select the route type:
"Fast route", "Short route", or
"Optimized route" and press OK to
confirm.
MNO
PQRS
Select the "Save to address book" function to record the address
entered in a directory file. Press OK to confirm the selection.
The PEUGEOT Connect Media allows more than 4 000 contact
records to be saved.
Delete list
MEDIA
Start route guidance
Repeat steps 5 to 7 for the "Street"
and "House number" functions.
Delete entry
RADIO
7
To speed up the process, the post code can be entered directly
after selecting the "Postal code" function.
Use the virtual keypad to enter the letters and digits.
RADIO
Then select "Start route guidance"
and the press OK to confirm.
Select the road with the colour
corresponding to the route chosen
and press OK to confirm and start
guidance.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
It is also possible to select a destination via "Choose from address
book" or "Choose from last destinations", by selecting a junction, a
town centre, geographic coordinates, or directly on the "Map".
Choose from address book
Choose from last destinations
223
04 NAVIGATION - GUIDANCE
Setting and navigating to my "Home
address"
Select your home address and confirm.
Then select "Edit entry" and confirm.
To be set as the "Home address", an address must first be
entered in the address book, for example from "Destination
input" / "Address input" then "Save to address book".
NAV
Press the NAV button twice to display
the Navigation Menu.
RADIO
MEDIA
NAV
TRAFFIC
Navigation Menu
ADDR
BOOK
TRAFFIC
2
5
JKL
8
3
DEF
6
Select "Set as Home address" and
confirm to save.
RADIO
MEDIA
NAV
TRAFFIC
2
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
ADDR
BOOK
1
4
MNO
GHI
9
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
TUV
WXYZ
PQRS
TUV
WXYZ
*
0
#
*
0
#
ADDR
BOOK
1
4
7
224
SETUP
ABC
SETUP
ABC
PQRS
GHI
Destination input
ADDR
BOOK
1
Edit entry
7
NAV
TRAFFIC
4
4
MEDIA
NAV
7
1
RADIO
MEDIA
GHI
GHI
Select "Destination input" and confirm.
Then select "Choose from address
book" and confirm.
RADIO
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Set as home address
To start navigation towards "Home", press NAV twice to display the
Navigation Menu, select "Destination input" and confirm.
Then select "Navigate HOME" and confirm to start guidance.
04 NAVIGATION - GUIDANCE
When the map is displayed on the screen, you can select "Map Settings"
then "2D Map / 2.5D Map / 3D Map / North Up / Heading Up". The display
of buildings in 3D mode depends on the progress in town mapping.
Route options
RADIO
NAV
MEDIA
NAV
TRAFFIC
1
Press the NAV button.
Press the NAV button again or select
the Navigation Menu function and
press OK to confirm.
ADDR
BOOK
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Route dynamics
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Navigation Menu
Select the "Route options" function
and press OK to confirm.
Select the "Route dynamics"
function.
This function provides access to
the "Traffic independent", "Semidynamic" and "Dynamic" options.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
Select the "Avoidance criteria"
function. This function provides
access to the "Avoid" options
(motorways, toll roads, ferries,
tunnels).
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Avoidance criteria
Route options
Select the "Route type" function and
press OK to confirm. This function
allows you to change the route type.
Route type
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
SETUP
2
ABC
5
3
DEF
Turn the ring and select the
"Recalculate" function to take into
account the route options selected.
Press OK to confirm.
6
GHI
JKL
MNO
7
8
9
PQRS
TUV
WXYZ
*
0
#
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Recalculate
225
04 NAVIGATION - GUIDANCE
Stopovers can be added to or deleted from the route once the destination
has been selected.
Adding a stopover
RADIO
NAV
MEDIA
NAV
TRAFFIC
1
Press the NAV button.
Press the NAV button again or select
the "Navigation" Menu function and
press OK to confirm.
ADDR
BOOK
4
RADIO
MEDIA
NAV
TRAFFIC
Enter a new address, for example.
SETUP
2
ABC
5
WXYZ
*
0
#
7
8
2
5
JKL
8
3
DEF
6
MNO
9
Address input
Once the new address has
been entered, select "Start route
guidance" and press OK to confirm.
SETUP
5
SETUP
ABC
#
TUV
JKL
4
7
WXYZ
PQRS
4
1
GHI
0
9
GHI
ADDR
BOOK
*
MNO
8
2
TRAFFIC
TUV
JKL
ABC
NAV
PQRS
7
1
MEDIA
6
GHI
ADDR
BOOK
RADIO
3
DEF
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
3
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Start route guidance
"Navigation" Menu
Select the "Stopovers" function and
press OK to confirm.
Position the stopover on the list and
press OK to confirm.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
Add stopover
226
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
2
ABC
5
JKL
8
Repeat operations 1 to 7 as many times as necessary then select
"Recalculate" and press OK to confirm.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
6
MNO
9
#
9
#
3
DEF
WXYZ
6
WXYZ
0
8
0
MNO
TUV
5
TUV
3
*
2
JKL
*
DEF
PQRS
SETUP
ABC
PQRS
SETUP
Stopovers
Select the "Add stopover" function
(5 stopovers maximum) and press
OK to confirm.
RADIO
To change the stopovers, repeat operations 1 to 3 and select
"Rearrange route" (select a stopover, delete it or move it on the
list using the ring to change the order, confirm its new position and
finish with "Recalculate").
04 NAVIGATION - GUIDANCE
The points of interest (POIs) indicate all of the service locations in the
vicinity (hotels, various businesses, airports...).
Searching for points of interest (POI)
RADIO
NAV
MEDIA
NAV
TRAFFIC
Press the NAV button.
Press the NAV button again or select
the Navigation Menu function and
press OK to confirm.
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
MEDIA
NAV
TRAFFIC
ADDR
BOOK
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
A list of cities present in the country selected can be accessed via
the LIST button on the virtual keypad.
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
POI search
Select the "POI nearby" function to
search for POIs around the vehicle.
RADIO
POI in city
RADIO
Navigation Menu
Select the "POI search" function and
press OK to confirm.
Select the "POI in city" function to
search for POIs in the city required.
Select the country then enter the
name of the city using the virtual
keypad.
Select the "POI in country" function
to search for POIs in the country
required.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
RADIO
MEDIA
NAV
TRAFFIC
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
ADDR
BOOK
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
POI in country
POI nearby
Select the "POI near destination"
function to search for POIs near the
point of arrival of the route.
POI near destination
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
Select the "POI near route" function
to search for POIs near the route.
SETUP
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
1
4
GHI
7
2
ABC
5
JKL
8
3
7
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
POI near route
227
04 NAVIGATION - GUIDANCE
This icon appears when several POIs are grouped
together in the same area. Zooming in on this icon
shows details of the POIs.
List of principal points of interest (POI)
228
Service station
Airport
Cinema
LPG station
Railway station
Theme parks
Garage
Bus station
Hospital
PEUGEOT
Port
Pharmacy
Motor racing circuit
Industrial estate
Police station
Covered car park
Supermarket
School
Car park
Bank
Post office
Rest area
Vending machine
Museum
Hotel
Tennis court
Tourist information
Restaurant
Swimming pool
Risk area*
Refreshment area
Golf course
Picnic area
Winter sports resort
Cafeteria
Theatre
* According to availability in the country.
04 NAVIGATION - GUIDANCE
Updating POIs
Press NAV, select Navigation Menu,
then "Settings", then "Update personal
POI".
Download the "POIs" update file onto
an SD card or USB memory stick from
the Internet. This service is available at
http://peugeot.navigation.com.
RADIO
NAV
MEDIA
NAV
TRAFFIC
Navigation Menu
ADDR
BOOK
1
4
GHI
7
Settings
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Update personal POI
The files must be copied to the root on the chosen medium.
Insert the medium (SD card or USB memory
stick) containing the POI database into the
system's SD card reader or USB port.
Select the medium ("USB" or "SD-Card")
used and press OK.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Successful downloading is confirmed by a message.
The system restarts.
The POIs version can be found in the SETUP \ System menu.
229
04 NAVIGATION - GUIDANCE
Spoken instruction settings
When the navigation is displayed in
the screen, press OK then select or
deselect "Voice advice" to activate
or deactivate the spoken guidance
instructions.
Use the volume button to adjust the
volume.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
SETUP
1
2
ABC
4
GHI
7
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Select the "Settings" function and
press OK to confirm.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Settings
The volume of the Risk Areas POIs alert can only be adjusted
during this type of alert.
Select the "POI categories on Map"
function to select the POIs to be
displayed on the map by default.
Point of interest and risk area settings
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
POI categories on Map
NAV
Press the NAV button.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
Press the NAV button again or select
the Navigation Menu function and
press OK to confirm.
Navigation Menu
230
RADIO
MEDIA
NAV
TRAFFIC
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
ADDR
BOOK
1
4
GHI
7
Select "Set parameters for risk areas"
to gain access to the "Display on
map", "Visual alert" and "Sound alert"
functions.
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Set parameters for risk areas
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
05 TRAFFIC INFORMATION
The TMC (Traffic Message Channel) messages provide information
relating to traffic and weather conditions, received in real time and
transmitted to the driver audibly and visually on the navigation map.
The guidance system can then suggest an alternative route.
Configure the filtering and display
of TMC messages
Select the filter of your choice:
RADIO
TRAFFIC
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
Press the TRAFFIC button.
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Messages on route
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
All warning messages
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Only warnings on route
All messages
The list of TMC messages appears under the Traffic Menu sorted
in order of proximity.
Select "Geo. Filter".
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Geo. Filter
Press the TRAFFIC button again or
select the Traffic Menu function and
press OK to confirm.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Traffic Menu
Select "Select preferred list" and
press OK to confirm.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
When all of the messages on the route are selected, the addition
of a geographic filter is recommended (within a radius of 3 miles
(5 km) for example) to reduce the number of messages displayed
on the map. The geographic filter follows the movement of the
vehicle.
The filters are independent and their results are concealed.
We recommend:
a filter over 6 miles (10 km) around the vehicle in heavy traffic,
a filter over 30 miles (50 km) around the vehicle or a filter on
the route on motorway journeys.
231
05 TRAFFIC INFORMATION
Principal TMC symbols
Black and blue triangle: general information, for example:
Weather reports
Traffic reports
Wind
Fog
Parking
Snow / ice
Receiving TA messages
-
the station transmits TA messages.
-
the station does not transmit TA messages.
-
TA messages are not activated.
The TA (Traffic Announcement) function gives priority to TA alert
messages. To operate, this function needs good reception of a radio
station transmitting this type of message. When a traffic report is
transmitted, the current audio source (Radio, CD, ...) is interrupted
automatically to play the TA message. Normal playback of the audio
source resumes at the end of the transmission of the message.
Red and yellow triangle: traffic information, for example:
RADIO
Modified signage
Narrow carriageway
Slippery surface
Accident
Delay
Roadworks
Risk of explosion
Road closed
Demonstration
Danger
No entry
232
Traffic jam
MEDIA
NAV
TRAFFIC
With the current audio source displayed
on the screen, press the dial.
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
The shortcut menu for the source appears and gives access to:
TA
Select Traffic Announcements (TA)
and press the dial to confirm and go
to the associated settings.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
The external environment (hill, building, tunnel, underground car park...)
may interfere with the reception, including in RDS station tracking mode.
This phenomenon is a normal result of the way in which radio waves are
transmitted and does not in any way indicate a failure of the audio equipment.
06 RADIO
Selecting a station
RADIO
RDS - Regional mode
Press the RADIO button to display the
list of stations received locally sorted
in alphabetical order.
Select the station required by turning
the ring and press to confirm.
RADIO
MEDIA
NAV
TRAFFIC
When the current radio station is
displayed on the screen, press OK.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
The radio source short-cuts menu appears and provides access to
the following short-cuts:
TA
RDS
While listening to the radio, press buttons 
and  for the automatic search for a lower or
higher frequency.
When the "RADIO" screen is displayed, turn the
ring or use the 4-direction navigator to select the
previous or next station on the list.
RADIO
MEDIA
NAV
Radiotext
TRAFFIC
Regional prog.
AM
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
Press one of the buttons on the numeric keypad for more than
2 seconds to store the current station. A bleep confirms that it has
been stored.
Press the button on the numeric keypad to recall the stored radio
station.
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Select the function required and
press OK to confirm to gain access
to the corresponding settings.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
RDS, if displayed, allows you to continue listening to the same station
by automatic retuning to alternative frequencies. However, in certain
conditions, coverage of an RDS station may not be assured throughout
the country as radio stations do not cover 100 % of the territory. This
explains the loss of reception of the station during a journey.
233
07 MUSIC MEDIA PLAYERS
CD, MP3 / WMA CD, MP3 / WMA SD card /
USB player
Information and advice
The MP3 format, an abbreviation of MPEG 1, 2 & 2.5 Audio Layer 3
and the WMA format, an abbreviation of Windows Media Audio and
the property of Microsoft, are audio compression standards which
permit the recording of several tens of music files on a single disc.
Connecting an iPod:
To play MP3 type files, connect the iPod using the USB port (limited
functions).
To play ITunes files, connect the iPod using the auxiliary socket (AUX).
In order to be able to play a recorded CDR or CDRW, when
recording it is preferable to select the ISO 9660 level 1, 2 or Joliet
standard.
If the disc is recorded in another format it may not be played
correctly.
It is recommended that the same recording standard is always
used for an individual disc, with as low a speed as possible
(4x maximum) for optimum sound quality.
In the particular case of a multi-session CD, the Joliet standard is
recommended.
In order to be read, a USB memory stick must be formatted to FAT 32.
234
The audio equipment will only play audio files with the extension
".mp3" with a speed of between 8 Kbps and 320 Kbps and the
extension ".wma" with a speed of between 5 Kbps and 384 Kbps.
It also supports the VBR (Variable Bit Rate) mode.
No other type of file (.mp4, .m3u...) can be played.
It is advisable to restrict file names to 20 characters, without using
of special characters (e.g.: " " ? ; ù) to avoid any playing and
displaying problems.
During play, exit the "SD-Card" or "USB" source before removing
the SD card or the USB memory stick from its port.
To avoid any risk of theft, remove the SD card or the USB memory
stick when you leave your vehicle with the roof open.
07 MUSIC MEDIA PLAYERS
Selecting / Playing
CD, MP3 / WMA CD, MP3 / WMA SD card /
USB player
Insert the audio or MP3 CD in the
player, the SD card in the card
reader or the USB peripheral
in the USB port. Play begins
automatically.
RADIO
NAV
MEDIA
ESC
ADDR
BOOK
TRAFFIC
1
4
GHI
7
MP3 CDs, SD cards or USB peripherals are the compatible sources.
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Press the MEDIA button again or
select the "Media" Menu function and
press OK to confirm.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
"Media" Menu
The list of tracks or MP3/WMA files appears under "Media" Menu.
Select the "Select media" function
and press OK to confirm.
RADIO
MEDIA
NAV
TRAFFIC
Press this button.
When the "MEDIA" screen is
displayed, turn the ring up or down to
select the previous or next compatible
source.
1
4
GHI
7
RADIO
MEDIA
Press the MEDIA button.
NAV
TRAFFIC
5
JKL
8
3
DEF
6
MNO
WXYZ
0
#
ADDR
BOOK
7
SETUP
2
ABC
5
JKL
8
3
DEF
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Select media
Select the music source required.
Press OK to confirm. Play begins.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
TRAFFIC
MEDIA
9
TUV
4
NAV
2
ABC
*
GHI
MEDIA
SETUP
PQRS
1
RADIO
MEDIA
ADDR
BOOK
RADIO
The playing and displaying of an MP3/WMA compilation may
depend on the recording programme and/or the parameters used.
We recommend the ISO 9660 recording standard.
235
07 MUSIC MEDIA PLAYERS
Jukebox
When copying is in progress, switching off the ignition will interrupt the
process but it will resume directly when the ignition is switched on again.
Copying a CD, a USB memory stick or an SD card
to the hard disk
Insert an audio / MP3 CD, a USB
memory stick or an SD card.
RADIO
NAV
MEDIA
ESC
TRAFFIC
ADDR
BOOK
Select the tracks required then "Rip
selection" or select all of the tracks using
"Rip all".
SETUP
1
2
3
ABC
4
GHI
7
DEF
5
6
JKL
MNO
8
9
PQRS
TUV
WXYZ
*
0
#
Select "[New folder]" to create a new
folder or select an existing folder
(created previously).
Check that the active MEDIA source is that of the medium used
(CD, USB or SD card).
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
RADIO
MEDIA
NAV
TRAFFIC
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
[New folder]
MEDIA
Press the MEDIA button. Press the
MEDIA button again or select Media
Menu and press OK to confirm.
Select "Jukebox management" then
"Add files" and press OK at each step
to confirm.
RADIO
MEDIA
NAV
"Do you want to change the names of
the tracks that will be ripped?": select
"Yes" to change them or "No".
TRAFFIC
Yes
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Add files
Select "Add files from MP3-Disc" for
example and press OK to validate.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
Add files from MP3-Disc
236
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
No
To copy an MP3 CD, then select "Real
time ripping", "Fast ripping" / "High
quality (192 kbit/sec)" or "Standard
quality (128 kbit/sec)" then select "Start
ripping".
Confirm the warning message by
pressing "OK" to start the copy.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
RADIO
MEDIA
NAV
TRAFFIC
2
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
ADDR
BOOK
1
4
GHI
7
OK
SETUP
ABC
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
07 MUSIC MEDIA PLAYERS
Jukebox
Renaming or deleting an album
Playing the jukebox
Check that the active source is not the Jukebox in order to be able
to rename or delete a track / folder.
MEDIA
Activate the playing of a source other than the Jukebox (CD, radio,
etc...).
RADIO
MEDIA
MEDIA
NAV
Press the MEDIA button.
Press the MEDIA button again or
select Media Menu and press OK to
confirm.
RADIO
MEDIA
NAV
TRAFFIC
TRAFFIC
Press the MEDIA button.
Select "Jukebox management" and
press OK to confirm.
Press the MEDIA button again or
select Media Menu and press OK to
confirm.
Select "Jukebox management" and
press OK to confirm.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
RADIO
MEDIA
NAV
TRAFFIC
Modify content
MEDIA
NAV
TRAFFIC
SETUP
2
ABC
5
JKL
8
3
DEF
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
TUV
WXYZ
*
0
#
SETUP
2
5
8
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
9
#
JKL
RADIO
6
WXYZ
ABC
Select "Play options" and press OK to
confirm.
Select "Folders & Files" or "Playlists"
then press OK to confirm.
MNO
0
4
4
7
9
TUV
1
1
GHI
PQRS
6
*
7
ADDR
BOOK
3
PQRS
GHI
TRAFFIC
MNO
#
ADDR
BOOK
NAV
DEF
WXYZ
4
RADIO
8
0
7
Select "Modify content" and press
OK confirm.
5
*
GHI
Jukebox management
2
JKL
TUV
1
MEDIA
SETUP
ABC
PQRS
ADDR
BOOK
RADIO
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Press the ESC button to return to the first file level.
Playlists can be created in the Jukebox.
Media Menu> Jukebox management> Create new playlist. Add the
tracks required one by one then save the change. The "Playlists"
play mode must then be selected.
237
07 MUSIC MEDIA PLAYERS
Using an external device (AUX)
Viewing a video DVD
Audio / Video / RCA cable not supplied
RADIO
NAV
MEDIA
ESC
TRAFFIC
Insert the DVD in the player. Play begins
automatically.
If the DVD does not appear on the
screen, press the MODE button to
gain access to the "MEDIA" screen
which displays the DVD screen.
ADDR
BOOK
Connect the portable device (MP3 player, camcorder, camera…) to
the RCA sockets (white and red for audio; yellow for video) in the
glove box using a JACK/RCA audio cable.
SETUP
1
2
3
ABC
4
DEF
5
GHI
6
JKL
7
MNO
8
9
PQRS
TUV
WXYZ
*
0
#
MEDIA
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Press the MEDIA button then press
it again or select the Media Menu
function and press OK to confirm.
RADIO
MEDIA
NAV
TRAFFIC
If the external input is not activated, select "Ext. Device (Aux)
management" to activate it.
MEDIA
Press the MEDIA button to gain
access to the DVD menu at any time,
or to the functions of the Media Menu
which adjust the video (brightness/
contrast, image format...).
RADIO
MEDIA
NAV
TRAFFIC
The 4-direction navigator and the chromed ring allow you to move
the DVD selection cursor. Change chapter by pressing the  or
 button.
Select the video source required ("DVD-Video", "External
device (AV)"). Press OK to confirm. Play begins.
238
Select "Select media" then "External
device (AV)" and press OK to
activate it.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
External device
Select the AUX music source and
press OK to confirm. Play begins
automatically.
RADIO
MEDIA
NAV
TRAFFIC
The display and management of the controls is via the portable
device.
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
08 USING THE TELEPHONE
Choosing between the Bluetooth
telephone / internal telephone
RADIO
MEDIA
NAV
TRAFFIC
To activate the Bluetooth telephone or
the internal telephone, press PICK UP.
Select Phone menu, then "Select
phone" then choose between
"Telephone off", "Use Bluetooth
phone" or "Use internal phone". Press
OK at each step to confirm.
ADDR
BOOK
1
4
GHI
7
RADIO
MEDIA
NAV
TRAFFIC
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
The system can only be connected to one Bluetooth telephone and
one SIM card (Internal telephone) at the same time.
In this case, the phone book is synchronised with the Bluetooth
telephone.
239
08 USING THE TELEPHONE
* The services available via the telephone depend on the network, the SIM
card and the compatibility of the Bluetooth device used. Refer to your
telephone's manual and your operator to check which services you have
access to.
Pairing a Bluetooth telephone /
First connection
For safety reasons and because they require prolonged attention on the part
of the driver, the operations for pairing the Bluetooth mobile telephone to the
hands-free system of the PEUGEOT Connect Media Navigation (NG4 3D)
must be carried out with the vehicle stationary and the ignition on.
Visit www.peugeot.co.uk for more information (compatibility, more help, ...).
Enter the authentication code on the
telephone. The code to be entered
is displayed on the screen of the
system.
RADIO
MEDIA
NAV
TRAFFIC
Press the CALL button.
Search phone
240
TRAFFIC
ADDR
BOOK
1
4
GHI
7
RADIO
RADIO
Select "Search phone" and press OK
to confirm. Then select the name of
the telephone.
NAV
SETUP
2
ABC
3
DEF
5
6
JKL
8
MNO
9
PQRS
TUV
WXYZ
*
0
#
Once the telephone has been connected, the PEUGEOT Connect
Media Navigation (NG4 3D) can synchronise the address book and
the call list. This synchronisation may take a few minutes*.
Activate the telephone's Bluetooth function and
ensure that it is "visible to all" (refer to the telephone
instructions).
If no telephone has been paired, the
system prompts you to "Connect
phone". Select "Yes" and press OK to
confirm.
MEDIA
ADDR
BOOK
1
4
GHI
7
RADIO
MEDIA
NAV
TRAFFIC
2
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
ADDR
BOOK
1
4
GHI
7
MEDIA
NAV
TRAFFIC
SETUP
2
ABC
5
JKL
8
To pair another telephone, press the
TEL button, then select Phone menu,
then "Select phone" then "Connect
Bluetooth phone" then select the
telephone required.
Press OK at each step to confirm.
1
4
GHI
7
RADIO
MEDIA
NAV
TRAFFIC
MEDIA
NAV
TRAFFIC
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
ADDR
BOOK
1
4
GHI
7
SETUP
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
To delete a pairing, press TEL, select "Connect phone" then
"Delete pairing".
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
ADDR
BOOK
1
4
GHI
7
3
DEF
Pairing can be started from the telephone (refer to the telephone
instructions).
RADIO
ADDR
BOOK
SETUP
ABC
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
08 USING THE TELEPHONE
* The services available via the telephone depend on the network, the
SIM card and the compatibility of the Bluetooth device used. Refer to
your telephone's manual and your operator to check which services you
have access to. A list of mobile telephones which offer the best range of
services is available from dealers.
Connecting a Bluetooth telephone
For safety reasons and because they require prolonged attention
on the part of the driver, the operations for pairing the Bluetooth
mobile telephone to the hands-free system of the PEUGEOT
Connect Media Navigation (NG4 3D) must be carried out with the
vehicle stationary and the ignition on.
Once the telephone has been connected, the PEUGEOT Connect
Media Navigation (NG4 3D) can synchronise the address book and
the call list. This synchronisation may take a few minutes*.
Activate the telephone's Bluetooth function and
ensure that it is visible to all.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
Press the PICK UP button.
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
The list of telephones connected previously (maximum of 4)
appears in the multifunction screen. Select the telephone required
then select "Connect phone" for a new connection. Select "Delete
pairing" to cancel the connection to the telephone.
241
08 USING THE TELEPHONE
Using the internal telephone with
a SIM card
If you have declined to use the internal telephone for personal calls, you
can still connect a Bluetooth telephone to receive your calls on the vehicle's
audio system.
1
4
Extract the holder by pressing the eject button.
GHI
7
PQRS
*
2
ABC
5
JKL
8
TUV
0
3
DEF
6
MNO
9
WXYZ
Enter the PIN code on the keypad
then select OK and confirm.
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
GHI
7
#
SETUP
2
ABC
ABC
5
JKL
JKL
8
3
DEF
DEF
6
MNO
MNO
9
PQRS
PQRS
TUV
TUV
WXYZ
WXYZ
*
0
##
Remember PIN
Install the SIM card in the holder
and then insert it in the slot.
To remove the SIM card, repeat step 1.
For safety reasons and because they require prolonged attention
on the part of the driver, the SIM card installation operations must
be carried out when stationary.
242
When entering your PIN code, tick the "Remember PIN" tab to
allow use of the telephone without having to enter this code when
it is used subsequently.
The system asks "Do you want
to switch to the internal phone?",
select "Yes" if you wish to use your
SIM card for your personal calls.
Otherwise, only the emergency call
and the services will use the SIM
card.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Once the SIM card has been installed, the system can synchronise
the address book and the call list.
This synchronisation may take a few minutes.
08 USING THE TELEPHONE
Operating the telephone while driving is prohibited. It is recommended
that you park safely or use in preference the steering mounted controls.
Making a call
Receiving a call
RADIO
An incoming call is announced by a ring and a superimposed
display in the screen.
Select the "Yes" tab to accept or "No"
to refuse and confirm by pressing OK.
RADIO
MEDIA
NAV
TRAFFIC
ADDR
BOOK
1
4
GHI
7
Yes
MEDIA
NAV
TRAFFIC
Press the PICK UP button.
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
ADDR
BOOK
1
4
GHI
7
TUV
WXYZ
*
0
#
The PICK UP button accepts, the HANG UP button rejects the
incoming call.
RADIO
MEDIA
NAV
TRAFFIC
End call
Press the end of the steering mounted control to
accept the call or end the call in progress.
TRAFFIC
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
WXYZ
0
#
ADDR
BOOK
1
4
GHI
Phone menu
Select "Dial number", then dial the
telephone number using the virtual
keypad.
NAV
8
TUV
*
7
MEDIA
5
PQRS
The list of the last 20 calls made and received in the vehicle
appears under Phone menu. You can select a number and press
OK to make the call.
Select the Phone menu function and
press OK to confirm.
RADIO
2
JKL
9
PQRS
No
To hang up, press the HANG UP
button or press OK and select "End
call" then confirm by pressing OK.
SETUP
ABC
3
DEF
6
MNO
RADIO
MEDIA
NAV
TRAFFIC
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
ADDR
BOOK
1
4
GHI
7
SETUP
2
ABC
5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Dial number
9
PQRS
TUV
WXYZ
*
0
#
It is also possible to select a number from the address book. You
can select "Dial from address book". The PEUGEOT Connect
Media can record up to 4 096 entries.
It is always possible to start a call directly from the
telephone; park the vehicle as a safety measure.
Press the end of the steering mounted control for more than
two seconds to open the address book.
243
09 SCREEN MENU MAP(S)
1
2
3
3
2
MAIN FUNCTION
4
OPTION A
4
option A1
3
OPTION B…
Within 30 miles (50 km)
Read out settings
2
option A2
Within 6 miles (10 km)
3
On confirmation
Modify content
3
Edit playlist
3
Play options
3
Incoming messages
4
TMC station information
2
Create folder
3
4
1
Select preferred list
2
3
3
3
3
3
3
4
4
4
244
Messages on route
MEDIA
"Media" Menu
1
Select media
2
Only warnings on route
3
All warning messages
3
All messages
3
Geo. Filter
Deactivate PIN
Within 2 miles (3 km)
Within 3 miles (5 km)
3
3
2
3
Audio CD / MP3-Disc / DVD-Audio / DVD-Video
Jukebox (Folders & Files)
SD-Card
USB
External device (audio/AV)
Jukebox management
Add files
Playlists
Memory capacity
TRAFFIC
"Traffic" Menu
Folders & Files
Sound settings
2
Refer to the "Sound settings" menu details of
which are shown on the next page.
3
Video settings
2
3
3
3
4
4
4
Aspect ratio
Menu language
Display
Brightness
Contrast
Colour
3
3
2
3
AUX standard
Reset video settings
Ext. Device (Aux) management
3
3
2
2
3
AM
2
Refer to the "Sound settings"
menu below.
"Sound settings" Menu
1
2
2
2
3
Balance / Fader
Bass / Treble
Equalizer
Linear
4
Speed dependent volume
1
3
4
Destination input
2
3
4
4
4
4
Address input
Country
City
Street
House number
Intersection
City district
Geo position
Map
Stopovers
2
Abort guidance / Resume guidance
2
Save to address book
Choose from address book
3
"Navigation" Menu
Postal code
Choose from last destinations
3
NAV
Start route guidance
Navigate HOME
3
Reset sound settings
Manual tune
Sound settings
4
Loudness
2
2
4
Mute rear speakers
2
FM
4
Vocal
3
Waveband
2
4
Techno
3
"Radio" Menu
4
Rock/Pop
3
Off / Audio / Audio and Video (AV)
4
Jazz
3
RADIO
1
Classic
3
4
4
4
3
3
3
Add stopover
Address input
Navigate HOME
Choose from address book
Choose from last destinations
Rearrange route
Replace stopover
Delete stopover
245
Recalculate
3
4
4
4
4
Fast route
4
Short route
4
POI search
2
4
POI in city
3
3
"Phone" menu
1
Dial number
Avoid motorways
2
Avoid toll roads
2
Avoid tunnels
Avoid ferries
Recalculate
Dial from address book
Call lists
2
Messages
2
Select phone
2
POI in country
3
3
POI near route
3
Route options
2
Route type
3
4
4
4
4
"Address book" Menu
1
2
2
Short route
Optimized route
Subscr. service
Route dynamics
4
ADDR
BOOK
POI near destination
Settings
3
246
4
POI near destination
3
2
4
POI nearby
3
Dynamic
Avoidance criteria
3
Optimized route
Semi-dynamic
Traffic independent
2
2
2
2
Create new entry
Show memory status
Export address book
Delete all voice entries
Delete all entries
Delete folder "My Addresses"
3
3
3
Telephone off
Use Bluetooth phone
Use internal phone
Connect Bluetooth phone
Search phone
4
5
5
5
5
5
Disconnect phone
Rename phone
Delete pairing
Delete all pairings
Show details
Settings
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
Search for networks
3
Automatic answering system
PIN settings
3
Select ring tone
Change PIN
3
Phone / Ring tone volume
4
Enter mailbox number
4
Internal phone settings
Automatically accept call
Voice control
3
Activate PIN
Deactivate PIN
5
5
5
Show status
Deactivate waiting call
Call forward (?)
Show status
2
Menu language
3
4
Deactivate call forward
Set network automatically
Set network manually
5
Language & Speech
4
Select network
4
"SETUP" Menu
1
4
4
4
4
Deutsch
5
3
2
English
3
Español
3
Français
3
Basics
Examples
Tips
Speaker adaptation
SETUP
Activate call forward
Suppress own number
Tutorial
4
Signal waiting call (?)
Activate waiting call
Voice control active
4
SIM-card memory status
3
Portuguese
4
Remember PIN
3
Polski
4
New speaker adaptation
Delete speaker adaptation
Voice output volume
Date & Time
Set date & time
Date format
Time format
Italiano
Nederlands
247
2
Display
Brightness
3
4
4
4
4
4
4
4
248
4
4
Blue Flame
Day mode for map
Night mode for map
Auto. Day/Night for map
Celsius
Fahrenheit
Metric / Imperial
3
Orange Ray
Map colour
3
4
Steel
blue light (only in day mode)
Temperature
3
Colour
3
Units
2
4
2
3
3
3
km
Miles
System
Factory reset
Software version
Automatic scrolling
FREQUENTLY ASKED QUESTIONS
The table below groups together the answers to the most frequently asked questions concerning the PEUGEOT Connect Media Navigation (NG4 3D).
QUESTION
ANSWER
SOLUTION
There is a difference in
sound quality between
the different audio
sources (radio, CD…).
For optimum sound quality, the audio settings (Volume, Bass, Treble,
Ambience, Loudness) can be adapted to the different sound sources,
which may result in audible differences when changing source
(radio, CD…).
Check that the audio settings (Volume, Bass,
Treble, Ambience, Loudness) are adapted to
the sources listened to. It is advisable to set
the AUDIO functions (Bass, Treble, Front-Rear
Balance, Left-Right Balance) to the middle
position, select the musical ambience "Linear" and
set the loudness correction to the "Active" position
in CD mode or to the "Inactive" position in radio
mode.
The CD is ejected
automatically or is not
played by the player.
The CD is inserted upside down, is unplayable, does not contain any
audio data or contains an audio format which the player cannot play.
The CD is protected by an anti-pirating protection system which is not
recognised by the audio equipment.
-
The CD player sound is
poor.
Check that the CD is inserted in the player the
right way up.
Check the condition of the CD: the CD cannot
be played if it is too damaged.
Check the content in the case of a recorded
CD: consult the advice in the "Audio" section.
The audio equipment's CD player does not
play DVDs.
Due to inadequate quality, certain recorded
CDs will not be played by the audio system.
The CD used is scratched or of poor quality.
Insert good quality CDs and store them in suitable
conditions.
The audio equipment settings (bass, treble, ambiences) are unsuitable.
Set the treble or bass level to 0, without selecting
an ambience.
249
QUESTION
ANSWER
SOLUTION
The stored stations do
not function (no sound,
87.5 Mhz is displayed…).
An incorrect waveband is selected.
Press RADIO, select Radio Menu then
"Waveband" to return to the waveband on which
the stations are stored.
The quality of reception
of the radio station
listened to gradually
deteriorates or the stored
stations do not function
(no sound, 87.5 Mhz is
displayed…).
The vehicle is too far from the transmitter used by the station listened
to or there is no transmitter in the geographical area through which the
vehicle is travelling.
Activate the "RDS" function by means of the
short-cut menu to enable the system to check
whether there is a more powerful transmitter in the
geographical area.
The environment (hills, buildings, tunnels, basement car parks…) block
reception, including in RDS mode.
This phenomenon is normal and does not indicate
a failure of the audio equipment.
The aerial is absent or has been damaged (for example when going
through a car wash or into an underground car park).
Have the aerial checked by a PEUGEOT dealer.
Sound cut-outs of 1 to
2 seconds in radio mode.
During this brief sound cut-out, the RDS searches for any frequency
permitting better reception of the station.
Deactivate the "RDS" function by means of the
short-cut menu if the phenomenon is too frequent
and always on the same route.
With the engine off, the
system switches off after
a few minutes of use.
When the engine is switched off, the system's operating time depends on
the battery charge.
The switch-off is normal: the system switches to economy mode and
switches off to prevent discharging of the vehicle's battery.
Start the vehicle's engine to increase the battery
charge.
250
QUESTION
"TA" is selected.
However, certain traffic
jams along the route are
not indicated in real time.
ANSWER
SOLUTION
On starting, it is several minutes before the system begins to receive the
traffic information.
Wait until the traffic information is being received
correctly (displaying of the traffic information
symbols on the map).
In certain countries, only major routes (motorways…) are listed for the
traffic information.
This phenomenon is normal. The system is
dependent on the traffic information available.
The time taken to
calculate a route
sometimes seems longer
than usual.
The performance of the system may slow down temporarily if a CD/DVD
is being copied onto the Jukebox at the same time as a route is being
calculated.
Wait until the CD/DVD has been copied or stop
the copying before starting the guidance function.
The "Risk areas" audible
warning does not work.
The audible warning is not active.
Activate the audible warning on Navigation Menu,
Settings, Set parameters for risk areas.
The alert volume is set to minimum.
Increase the volume of the alert when passing a
"Risk area".
Does the emergency call
function work without a
SIM card?
No, as certain national regulations impose the presence of a SIM card in
order to make an emergency call.
Insert a valid SIM card in the slot.
The altitude is not
displayed.
On starting, the initialisation of the GPS may take up to 3 minutes to
receive more than 4 satellites correctly.
Wait until the system has started up completely.
Check that there is a GPS coverage of at least
4 satellites (long press on the SETUP button, then
select "GPS coverage").
Depending on the geographical environment (tunnel…) or the weather,
the conditions of reception of the GPS signal may vary.
This phenomenon is normal. The system is
dependent on the conditions of reception of the
GPS signal.
251
QUESTION
ANSWER
SOLUTION
The route calculation is
not successful.
The exclusion criteria may conflict with the current location (exclusion of
toll roads on a toll motorway).
Check the exclusion criteria on the Navigation
Menu ("Route options" - "Avoidance criteria").
There is a long waiting
period following the
insertion of a CD.
When a new medium is inserted, the system reads a certain amount of
data (directory, title, artist, etc.). This may take a few seconds.
This phenomenon is normal.
I cannot connect my
Bluetooth telephone.
The telephone's Bluetooth function may be switched off or the equipment
may not be visible.
-
The Bluetooth telephone is not compatible with the system.
A list of compatible Bluetooth mobile telephones is
available from the dealer network.
The volume of the
telephone connected
in Bluetooth mode is
inaudible.
The volume depends both on the system and on the telephone.
Increase the volume of the PEUGEOT Connect
Media Navigation (NG4 3D), to maximum
if required, and increase the volume of the
telephone if necessary.
The system does not play
the DVD.
The region protection may not be compatible.
Insert DVDs which have compatible region
protection.
I cannot copy the CD to
the Jukebox.
The wrong source is selected.
Change the active source to CD.
The CD is copy-protected.
It is normal that a protected CD cannot be copied.
252
-
Check that your telephone's Bluetooth
function is switched on.
Check that your telephone is visible.
QUESTION
The system does not
receive SMS.
I cannot update the risk
area POIs.
ANSWER
SOLUTION
The Bluetooth mode does not permit sending of the SMS to the system.
Use your SIM card and the internal telephone.
The SIM card used is a twin card.
Use the original SIM card to receive the SMS.
The Navigation Menu - "Update personal POI" is not displayed.
Check that the medium used for the update (SD
card or USB memory stick) is inserted correctly.
An error message is displayed at the end of the procedure.
-
Start the procedure again in full.
Consult a PEUGEOT dealer if the problem
persists.
Check that the data on the MEDIUM is
supplied by an official partner of PEUGEOT.
The voice frequencies
(DTMF) are not active
when I am communicating
and I press numbers on
the keypad.
The numeric buttons on the keypad are only active for calls if the display
is in telephone mode.
To activate them, press the MODE button until the
telephone is displayed on the screen.
An risk area which
does not concern me is
displayed on the screen.
The risk areas are displayed near a point defined on the map and in
relation to a direction of travel.
The alert may be triggered when travelling under a
road or near a road which is a Risk area.
253
254
PEUGEOT Connect
onnect Navigation (RT6)
SATELLITE NAVIGATION SYSTEM
MULTIMEDIA BLUETOOTH
TELEPHONE AUDIO SYSTEM
CONTENTS
The system is protected in such a way that it will only
operate in your vehicle.
For safety reasons, the driver must only carry out
operations which require prolonged attention while the
vehicle is stationary.
When the engine is switched off and to prevent
discharging of the battery, the system switches off
following the activation of the energy economy mode.
01
02
03
04
05
06
07
08
09
10
11
First steps - Control panel
Steering mounted controls
General operation
Navigation - Guidance
Traffic information
Using the telephone
Radio
Music media players
Audio settings
Configuration
Screen menu map
Frequently asked questions
p.
p.
p.
p.
p.
p.
p.
p.
p.
p.
p.
256
p.
303
258
259
261
274
277
287
291
297
298
299
255
01 FIRST STEPS
Selection and confirmation OK dial:
Selection of an item on the screen or in a list or a menu,
then confirmation with a short press.
Other than for menus and lists, a short press displays a
contextual menu depending on the current screen.
Rotation with map displayed: zoom the map scale in
and out.
Open the
"Configuration" menu.
Long press: access
to the GPS coverage
and the navigation
demonstration mode.
Select:
the previous/next line in a list or menu.
the previous / next media folder.
step by step selection of the previous/
next radio frequency.
the previous / next MP3 folder.
Move up/down, in "Move the map" mode.
Short press without the
engine running: on / off.
Short press with the engine
running: audio source off /
restore.
Volume adjustment (each
source is independent,
including TA messages and
navigation instructions).
MODE button: Selection
of the type of permanent
display.
Long press: black
screen (DARK).
256
Access to the
"Navigation - guidance"
menu and display the
recent destinations.
Open the "Traffic
information" menu
and display the current
traffic alerts.
Abandon the current
operation, up one level
in the menu.
Long press: return to
the permanent display.
Select:
the next lower / higher radio
frequency automatically.
the previous / next CD track, MP3
track or media.
the left / right of the screen when a
menu is displayed.
Move left / right in "Move the map" mode.
01 FIRST STEPS
Access to the "RADIO" menu and
display the list of stations received.
Long press: display the audio settings
screen for the radio tuner source.
Access to the "MUSIC" menu, and display of the CD/MP3/
Apple® tracks and folders.
Long press: display the audio settings screen for the
"MEDIA (CD/USB/iPod/Streaming/AUX)" sources.
Open the "Telephone" menu
and display the list of recent
calls or accept an incoming call.
Continuous press:
reinitialisation of the system.
Short press: select pre-set radio station.
Long press: pre-set the current station.
257
02 STEERING MOUNTED CONTROLS
RADIO: change to the next radio station in the list.
Long press: automatic search for a higher frequency.
CD: select the next track.
CD: continuous press: fast forward play.
RADIO: select the previous/next preset
station.
Select the next entry in the address book.
RADIO: change to the previous radio
station in the list.
Long press: automatic search for a
lower frequency.
CD: select the previous track.
CD: continuous press: fast reverse.
Volume increase.
Volume decrease.
258
SRC/TEL button:
change the audio source,
start a call from the address book,
call/end call on the telephone,
press for more than 2 seconds: access
to the address book.
Mute: press the volume
increase and decrease
buttons simultaneously.
Restore the sound by
pressing one of the
two volume buttons.
03 GENERAL OPERATION
Press the MODE button several times in succession for access to the following displays:
"RADIO"
"MAP IN WINDOW"
(If navigation guidance in
progress)
"TELEPHONE"
(If conversation in progress)
"FULL SCREEN MAP"
SETUP: PARAMETERS
date and time, display configuration, sound, vehicle
settings.
For cleaning the screen, the use of a soft, non-abrasive cloth
(spectacles cloth) is recommended, with no additional product.
Changing the audio source:
RADIO: RADIO broadcasts.
MUSIC: playing MUSIC.
For the details of the menus, refer to the "Screen menu map"
section.
259
03 GENERAL OPERATION
Display according to context
A press on the knob gives access
to short-cut menus according to the
display in the screen.
RADIO:
1
Activate / Deactivate TA
1
Activate / Deactivate RDS
1
Change waveband
2
2
1
FM
AM
TA
1
1
1
Private mode
1
Put call on hold
260
Hang up
MUSIC MEDIA
PLAYERS, CD or USB
(according to media):
Select destination
1
2
2
2
1
Normal
1
Random
1
Random on all media
Repetition
1
Stop / Restore guidance
Directory
GPS coordinates
Divert route
1
Move the map
2
2
2
2
FULL SCREEN MAP OR
IN A NEW WINDOW:
Enter an address
1
Play modes:
1
TELEPHONE
(call in progress):
DTMF ring tones
2
1
Info. on location
Select as destination
Select as stage
Save this place (contacts)
Quit map mode
Guidance criteria
04 NAVIGATION - GUIDANCE
Access to the "Navigation" menu
To make full use of all of the
functions of your navigation
system, update the mapping
regularly. Contact a
PEUGEOT dealer or order
your mapping update at
http://peugeot.navigation.com
"Navigation - guidance"
Press NAV.
List of recent destinations.
A short press on the end of the
lighting control stalk repeats
the last navigation message.
To delete the list of recent destinations, select "Guidance
options" in the navigation menu then select "Delete last
destinations" and confirm. Select "Yes" then confirm.
Deleting just one destination is not possible.
"Select destination"
"Journey leg and route"
"Guidance options"
"Map management"
"Stop / Restore guidance"
Go from the list to the menu (left/right).
or
261
04 NAVIGATION - GUIDANCE
Selecting a destination
Towards a new destination
Press NAV to display the
"Navigation - guidance" menu.
Select "Select destination" and
confirm, then select "Enter an address"
and confirm.
Select the "Country" function then
confirm.
Select the "Town" or "Post code"
function then confirm.
Select the letters in the name of the
town or the characters in a post code
one at a time, confirming each one with
the knob.
262
Selection the town from the list offered,
then confirm.
A pre-set list (by entering the first few
letters) of the towns in the country
selected can be accessed directly by
selecting and confirming "List" in the
screen.
If possible, enter the "Road" and "N°/X"
information in the same way.
Select "Archive" to save the address entered in a contact file.
The system allows up to 400 contact files to be recorded.
Confirm "OK" to start guidance.
Select the guidance criteria: "Fastest
route", "Shortest route" or optimised
"Distance/Time", then select the
desired restriction criteria: "With tolls",
"With Ferry", or "Traffic info" then
confirm "OK".
04 NAVIGATION - GUIDANCE
Towards a recent destination
Press NAV to display the
"Navigation - guidance" menu.
Select the desired destination and
confirm to start guidance.
Towards a contact in the contacts directory
Navigation towards a contact is only possible if it has an address
entered in the audio navigation system.
Press NAV to display the
"Navigation - guidance" menu.
Delete recent destinations
Press NAV to display the
"Navigation - guidance" menu.
Select "Options" and confirm and then
"Delete recent destinations" and
confirm.
Select "Select destination" and
confirm, then select "Directory" and
confirm.
Selection the desired destination from
your contacts and confirm "OK" to start
the guidance.
263
04 NAVIGATION - GUIDANCE
Towards GPS coordinates
Press NAV to display the
"Navigation - guidance" menu.
Towards a point on the map
With the map displayed, press OK to
display the contextual menu. Select
"Move the map" and confirm.
Select "Select destination" and
confirm, then select "GPS coordinates"
and confirm.
Move the cursor using the control to
identify the desired destination.
Enter the GPS coordinates and
confirm "OK" to start the guidance.
Press OK to display the contextual
menu for "Move the map" mode.
Select "Select as destination" or
"Select as stage" and confirm.
264
04 NAVIGATION - GUIDANCE
Towards points of interest (POI)
Press NAV to display the
"Navigation - guidance" menu.
Select the "Enter an address" function
and confirm, then select Select
destination and confirm.
To select a POI close to your current
location, select "POI" and confirm, then
select "Around the current place" and
confirm.
To select a POI as a stage on the route,
select "POI" and confirm, then select "On
the route" and confirm.
To select a POI as a destination, first
enter the country and town (see "Towards
a new destination"), select "POI" and
confirm, finally select "Near" and confirm.
The points of interest (POI) indicate all of the service locations in the vicinity
(hotels, various businesses, airports...).
Select "Search by Name" to search for POIs by name and not by
proximity.
Search for POIs in the categories
suggested in the following pages.
Select the POI and confirm "OK" to start
the guidance.
265
04 NAVIGATION - GUIDANCE
This icon appears when several POIs are grouped
together in the same area. Zooming in on this icon
shows details of the POIs.
List of principal points of interest (POI)
Service station
Airport
Cinema
Garage
Railway station
Theme parks
PEUGEOT
Bus station
Hospital, Chemist,
Vet
Covered car park
Port
Police station
Car park
Industrial estate
School
Rest area
Supermarket
Town hall
Hotel
Vending machine
Post office
Restaurant
Sports complex, sports centre,
sports ground
Museum, Culture, Theatre,
Historic monument
Cafeteria
Swimming pool
Tourist information, Tourist
attraction
Bed and breakfast
Winter sports resort
Risk areas / Danger
areas*
An annual mapping update allows new points of interest to be presented to you.
You can also update the Risk areas / Danger areas every month.
The detailed procedure is available on:
http://peugeot.navigation.com.
266
* According to availability in the country.
04 NAVIGATION - GUIDANCE
Settings for risk area / danger area alerts
Press NAV to display the "Navigation guidance" menu.
These functions are only available if risk areas have been
downloaded and installed on the system.
The detailed procedure for updating risk area POIs can be found at
http://peugeot.navigation.com.
Select "Guidance options" and confirm,
then select "Set parameters for risk
areas" and confirm.
Select:
"Visual alert"
"Audible alert"
"Alert only in guidance"
"Overspeed alarm only".
The choice of time of notification defines
how long in advance that Risk area
warnings are given.
Select "OK" to confirm the screen.
267
04 NAVIGATION - GUIDANCE
Adding a stage
Press NAV to display the
"Navigation - guidance" menu.
Organising stages
To organise stages, carry out
operations 1 to 2 again, then select
"Order/delete journey legs" and
confirm.
Select "Journey leg and route" then
confirm.
Select the stage that you want to move
in the order.
Select "Add a stage" then confirm.
The address of the stage is entered as
a destination, by "Enter an address",
a contact in "Directory", or "Previous
destinations".
Select and confirm to save the
modifications.
Select "Delete" to delete the stage.
Select "Close to" a route passing
close to the stage or "Strict" for a route
passing through the stage.
Confirm "OK" to start the guidance, and
give a general indication of the guidance
route.
268
04 NAVIGATION - GUIDANCE
Route options
Calculation criteria
Press NAV to display the
"Navigation - guidance" menu.
Select "Define calculation criteria" and
confirm.
This function allows modification of:
the guidance criteria: ("Fastest
route", "Shortest route",
"Distance/Time"),
the exclusion criteria: ("With tolls"
or "With Ferry"),
traffic avoidance: ("Traffic info").
If traffic avoidance (Traffic info) is selected, the system suggests
an alternative route if there is a delay on the guidance route.
Select "Guidance options" and confirm.
Select "OK" and confirm to save the
modifications.
269
04 NAVIGATION - GUIDANCE
Map management
Selecting the points of interest displayed on the map
Press NAV to display the
"Navigation - guidance" menu.
Select "Map management" and confirm.
Select "Map details" and confirm.
270
Select from the various categories the
ones that you want to display on the
screen.
Select "Default" to have only "Filling stations, garages"
and "Risk areas" appear on the map (if installed in the system).
Select "OK" then confirm and
select "OK" again then confirm to save
the modifications.
04 NAVIGATION - GUIDANCE
Map orientation
Press NAV to display the
"Navigation - guidance" menu.
Select:
"Vehicle direction" to have the map
follow the direction of travel,
"North direction" to keep the map
always North up,
"Perspective view" to display a
perspective view.
Select "Map management" and confirm.
The colour of the map, different from the day and night mode, is
configured in the "SETUP" menu.
Select "Map orientation" and confirm.
Street names are visible on the map from the 100 m scale.
271
04 NAVIGATION - GUIDANCE
Navigation voice synthesis
Adjusting the volume / Deactivation
The volume of messages can be adjusted during the transmission
of the message using the volume adjustment control.
Select the volume graph and confirm.
The volume setting of guidance messages is also accessible via
the "SETUP" / "Voice synthesis" menu.
Press NAV to display the
"Navigation - guidance" menu.
Select "Guidance options" and confirm.
Select "Set speech synthesis" and
confirm.
272
Adjust the volume to the desired level
and confirm.
Select "Deactivate" to deactivate voice messages.
Select "OK" and press the dial to
confirm.
04 NAVIGATION - GUIDANCE
Male voice / Female voice
Press SETUP to display the
configuration menu.
Select "Voice synthesis" and confirm.
Select "Select male voice" or "Select
female voice" then confirm "Yes" to
activate a male or female voice. The
system restarts.
273
05 TRAFFIC INFORMATION
Access to the "Traffic information" menu
"Traffic information"
Press "TRAFFIC".
List of TMC messages in order
of distance from the vehicle.
"Geographic filter"
"Select TMC station"
(automatic, manual)
"Display/Do not display
messages"
Go from the list to the menu (left/right).
or
274
05 TRAFFIC INFORMATION
Configure the filtering and display of TMC messages
TMC (Traffic Message Channel) messages contain information on traffic and weather conditions, received in real time and transmitted to the
driver in the form of audible announcements and symbols on the navigation map.
The navigation system can then suggest an alternative route to avoid a traffic problem.
Press the TRAFFIC button to display
the "Traffic information" menu.
The system offers a choice of:
"Retain all the messages",
or
"Retain the messages"
- "Around the vehicle", (confirm
the mileage to modify and select
the distance),
- "On the route".
Select the "Geographic filter" function
and confirm.
Confirm "OK" to save the modifications.
We recommend:
a filter on the route and
a filter around the vehicle of:
- 12 miles (20 km) in urban areas,
- 30 miles (50 km) on motorways.
275
05 TRAFFIC INFORMATION
Principal TMC symbols
Receiving TA messages
Black and blue triangle: general information, for example:
The TA (Traffic Announcement) function gives priority to TA alert
messages. To operate, this function needs good reception of a
radio station transmitting this type of message. When a traffic report
is transmitted, the current audio source (Radio, CD, USB, ...) is
interrupted automatically to play the TA message. Normal playback
of the audio source resumes at the end of the transmission of the
message.
Weather reports
Traffic reports
Wind
Fog
Parking
Snow / ice
Press RADIO to display the "FM / AM
band" menu.
Red and yellow triangle: traffic information, for example:
276
Modified signage
Narrow carriageway
Slippery surface
Accident
Delay
Roadworks
Risk of explosion
Road closed
Demonstration
Danger
No entry
Traffic jam
Select "Guidance options" then
confirm.
Activate or deactivate "TA" then confirm.
The volume setting for TA messages can be adjusted only during the
transmission of this type of alert.
Activate or deactivate the function at any time by pressing
the button.
During a message, press the button to interrupt it.
06 USING THE TELEPHONE
Access to the "Telephone" menu
In the top bar of the permanent
display
"Telephone"
No telephone connected.
Press this button.
List of recent calls sent and
received with the telephone
connected to the system.
"Dial"
"Directory of contacts"
"Contacts management"
"Phone functions"
"Bluetooth functions"
"Hang up"
Telephone connected.
Incoming call.
Outgoing call.
Synchronisation of
contacts in progress.
Telephone call in
progress.
To make a call, select a number in the list and confirm "OK"
to start the call.
Connecting a different telephone deletes the list of
recent calls.
Go from the list to the menu (left/right).
or
277
06 USING THE TELEPHONE
Pairing a Bluetooth telephone
First connection
You can check the compatibility of your telephone
at www.peugeot.co.uk (services).
Quick procedure from the telephone
For reasons of safety and because they require prolonged attention
on the part of the driver, the operations for pairing the Bluetooth
mobile telephone to the hands-free system of the audio unit must be
carried out with the vehicle stationary.
Procedure from the system
Activate the telephone's Bluetooth function
and ensure that it is "visible to all" (telephone
configuration).
In the Bluetooth menu of your telephone, select
the name of the system from the list of devices
detected.
Press this button.
Enter a minimum 4 figure code in the telephone and
confirm.
Enter the same code in the system,
select "OK" and confirm.
278
Select "Bluetooth functions" and
confirm.
Select "Peripherals search" and
confirm.
The list of peripheral devices detected
is displayed. Wait until the "Connect"
button is available.
06 USING THE TELEPHONE
The services available depend on the network, the SIM card and the compatibility of the Bluetooth telephone used. Check the telephone
manual and with your network provider for details of the services available to you.
Select the name of the desired
peripheral from the list of devices
detected then confirm
Select "Connect" and confirm.
The system offers to connect the
telephone:
in "Hands-free mode" (telephone
only),
in "Audio" mode (streaming: playing
music files on the telephone),
or "All" (for selection of both
modes).
Select "OK" and confirm.
The "Hands-free mode" should be used in preference if
"Streaming" is not desired.
The ability of the system to connect in only one mode depends on
the telephone. The two modes may both connect by default.
Enter a minimum 4 figure code in the telephone
and confirm.
Enter the same code in the system,
select "OK" and confirm.
Then accept automatic connection on the telephone to allow the
telephone to reconnect automatically every time the vehicle is
started.
Depending on the type of telephone, the system will ask you to
accept or not the transfer of your contacts.
On return to the vehicle,the last telephone connected
automatically reconnects, within around 30 seconds after
switching on the ignition (Bluetooth activated and visible).
To modify the automatic connection mode, remove the pairing
and pair the telephone again with the desired mode.
279
06 USING THE TELEPHONE
Directory configuration / Synchronisation with the telephone
Press PHONE then select "Contacts
management" and confirm.
Select "New contact" to enter a new
contact.
Select "Sort by Name/First name" to
choose the order in which they appear.
Select "Delete all contacts" to delete
the contacts saved in the system.
280
Select "Import all the entries" to import
all the contacts in the telephone and
save them in the system.
Once imported, a contact remains visible
whatever telephone is connected.
Select "Synchronization options":
No synchronization: only the
contacts saved in the system
(always present).
Display telephone contacts: only the
contacts saved in the telephone.
Display SIM card contacts: only the
contacts saved on the SIM card.
Display all phone contacts:
contacts on the SIM card and in the
telephone.
Select "Contact mem. status" to see the
number of contacts saved in the system
or imported, and the free memory.
06 USING THE TELEPHONE
Editing, importing or deleting a contact
Press PHONE then select "Directory of
contacts" and confirm.
It is not possible to modify or delete contacts in the telephone or the
SIM card via the Bluetooth connection.
Select the desired contact and confirm.
Once the contact has been imported, the Bluetooth symbol
disappears, replaced by the telephone symbol which shows that the
contact has been saved in the system.
Select "Open" to view a contact on the
telephone or modify a contact saved in
the system.
In the "Directory of contacts" menu, the import and deletion of
contacts is done one by one.
Select "Import" to copy a contact from
the telephone to the system.
Select OK or press the back button to exit
this menu.
Select "Delete" to delete a contact
recorded in the system.
281
06 USING THE TELEPHONE
Making a call
Use of the telephone is not recommended while driving. We recommended
that you park safely or make use of the steering mounted controls.
Calling a new number
Calling a contact
Press PHONE twice.
Press TEL or twice on PHONE.
Select "Directory of contacts" then
confirm.
Select "Dial" then confirm.
Select the desired contact and confirm.
If access was via the PHONE button,
select "Call" and confirm.
Dial the telephone number using the
virtual keypad selecting each number
in turn.
Confirm "OK" to make the call.
282
Select the number and confirm to start
the call.
06 USING THE TELEPHONE
Ending a call
Calling a recently entered number
Press TEL, select "Call list" and
confirm,
Press PHONE then select "OK" to end
the call.
or
press PHONE to display the calls log.
Or make a long press on TEL at the
steering mounted controls.
Or make two short presses on TEL at
the steering mounted controls.
Select the desired number and confirm.
To erase the calls log, press PHONE twice, select "Phone
functions" and confirm then select "Delete calls log" and confirm.
It is always possible to start a call directly from the telephone; park
the vehicle as a safety measure.
Or press the MODE button, as many
times as necessary, until the telephone
screen is displayed.
Press "OK" to display the contextual
menu then select "Hang up" and confirm.
283
06 USING THE TELEPHONE
Receiving a call
An incoming call is announced by a ring and a superimposed display
on the screen.
"Yes" to accept the call is selected by
default.
Press "OK" to accept the call.
Select "No" and confirm to reject the
call.
A short press on TEL accepts an
incoming call.
A long press on TEL rejects an incoming
call.
284
06 USING THE TELEPHONE
Options during a call*
During a call, press the MODE button
several times to select display of the
telephone screen, then press "OK" to
open the contextual menu.
Or make a short press on this button.
Select "Private mode" and confirm to
take the call on the handset.
Or select "Hands-free mode" and
confirm to take the call via the vehicle's
speakers.
Select "DTMF ring tones" to use the
numerical keypad, so as to navigate
through the menu of an interactive vocal
server.
Select "Hang up" to end the call.
It is possible to hold a 3-way conference
call by making 2 calls in succession*.
Select "Conference mode call" in the
contextual menu accessible using this
button.
Select "Put call on hold" and confirm to
put the current call on hold.
Or select "Resume the call" and
confirm to resume the call on hold.
* Depending on the compatibility of the phone and your service plan.
285
06 USING THE TELEPHONE
Managing paired telephones
Press PHONE twice.
Changing the ringtone
Press PHONE twice.
Select "Phone functions" and confirm.
Select "Bluetooth functions".
Select "Ring options" and confirm.
Select "List of the paired peripherals"
and confirm.
It is possible to:
"Connect" or "Disconnect" the
selected telephone,
delete the pairing of the selected
telephone.
It is also possible to select all pairings.
286
You can adjust the volume and the type
of ringtone.
Select "OK" and confirm to save the
changes.
07 RADIO
Access to the "Radio" menu
"FM / AM band / DAB"
Press RADIO.
Alphabetical list of stations
received.
"Change waveband" ("AM / FM / DAB")
"Guidance options" ("TA, RDS, FM
alternative frequencies / DAB")
"Audio settings" (see this section)
"Update radio list"
Go from the list to the menu (left/right).
Press  or  or use the rotary control to select the
previous or next station in the list.
or
287
07 RADIO
Changing waveband
Selecting a station
The external environment (hill, building, tunnel, underground car park...) may interfere with the reception, including in RDS station tracking mode. This
phenomenon is a normal result of the way in which radio waves are transmitted and does not in any way indicate a fault with the audio system.
The quality of reception is represented by the number of
active waves in this symbol.
Press RADIO or OK to display the
contextual menu.
Select "Change waveband".
Select "AM / FM" and confirm.
288
By alphabetical list
Press RADIO, select the station of your
choice and confirm.
By automatic frequency search
Press  or  for the automatic search
for a lower or higher radio frequency.
Or turn the thumb wheel at the steering
mounted controls.
By manual frequency search
Press  or  to adjust the radio
frequency step by step.
07 RADIO
Presetting a station
Activate / Deactivate RDS
RDS, if activated, allows you to continue listening to the same
station by automatic retuning to alternative frequencies. However,
in certain conditions, coverage of an RDS station may not be
assured throughout the entire country as radio stations do not
cover 100 % of the territory. This explains the loss of reception of
the station during a journey.
Press RADIO.
After selecting a station, press one of the buttons on the
numerical keypad for 2 seconds to preset the current
station.
An audible signal confirms that the station has been preset.
Select "Guidance options" then
confirm.
Press the button on the numerical keypad to recall a
preset station.
Or press then turn the thumb wheel at the steering
mounted controls.
Activate or deactivate "RDS" then
confirm.
289
07 RADIO
DAB (Digital
(Digital Audio Broadcasting)
Digital radio
Digital radio - DAB/FM auto tracking
Digital radio provides a higher quality reception and also the
graphical display of information for the radio station, by selecting
"Video mode" in "Radio favourites" (Options).
The different radio multiplex services offer a choice of stations
displayed in alphabetical order.
"DAB" does not have 100% coverage of the country.
When the digital signal is weak, "DAB / FM auto tracking" allows you
to continue listening to the same station, by automatically switching
to the corresponding analogue "FM" station (if one exists).
Press "RADIO".
Select "Change band" and confirm.
Press "RADIO".
Select "Options" and confirm.
Select "FM/DAB" and confirm.
Selection "DAB" and confirm.
Change of station in the same "multiplex".
Manual search for a "multiplex".
290
If "DAB / FM auto tracking" is on, there will be a difference of a few
seconds in the programme when the system changes to analogue
"FM" radio with sometimes a variation in volume.
Display of the "DAB" band then becomes "DAB (FM)".
When the strength of the digital signal is good again, the system
automatically switches back to "DAB".
If the "DAB" station you are listening to is not available on "FM"
("DAB/FM" option greyed out), or if "DAB / FM auto tracking" is not
on, the sound will be cut when the digital signal is too weak.
08 MUSIC MEDIA PLAYERS
Access to the "Music media player" menu
"MEDIA"
Press MUSIC.
List of the current media
tracks.
"Change media"
"Eject USB device" (if USB
connected)
"Play mode" ("Normal",
"Random", "Random on all
media", "Repetition")
"Audio settings" (see this section)
"Activate / Deactivate AUX input"
Go from the list to the menu (left/right).
or
291
08 MUSIC MEDIA PLAYERS
CD, MP3 CD / USB player
Information and advice
The audio equipment will only play audio files with ".wma, .aac, .flac,
.ogg and .mp3" file extensions and with a bit rate of between 32 Kbps
and 320 Kbps.
It also supports VBR (Variable Bit Rate) mode.
No other type of file (.mp4, .m3u...) can be played.
WMA files must be of the standard wma 9 type.
The sampling rates supported are greater than 32 KHz.
It is advisable to restrict file names to 20 characters, without using of
special characters (e.g.: " " ? ; ù) to avoid any playing and displaying
problems.
In order to be able to play a recorded CDR or CDRW, when recording
it is preferable to select the ISO 9660 level 1, 2 or Joliet standard.
If the disc is recorded in another format (udf, ...), it may not be played
correctly.
It is recommended that the same recording standard is always used
for an individual disc, with as low a speed as possible (4x maximum)
for optimum sound quality.
In the particular case of a multi-session CD, the Joliet standard is
recommended.
292
The system supports USB mass storage or iPod
devices via the USB port (suitable cable not supplied).
If a partitioned USB memory key is connected to the
system, only the first partition is recognised.
Control of the peripheral device is with the audio
system controls.
The number of tracks is limited to 2000 maximum,
999 tracks per folder.
If the current consumption at the USB port exceeds
500 mA, the system goes into protection mode and
deactivates the port.
Other peripherals, not recognised on connection, must
be connected to the auxiliary socket using a Jack cable
(not supplied).
In order to be read, a USB memory stick must be formatted FAT 16
or 32.
The system does not support the operation of an Apple® player and a
USB memory stick connected at the same time.
It is recommended that official Apple® USB cables are used to ensure
correct operation.
08 MUSIC MEDIA PLAYERS
Sources
Insert the CD in the player, insert the USB
memory stick in the USB player or connect the
USB peripheral to the USB port using a suitable
cable (not supplied)
The system builds playlists (in temporary
memory), an operation which can take from
a few seconds to several minutes at the first
connection.
Reduce the number of non-music files and the
number of folders to reduce the waiting time.
The playlists are updated every time the ignition
is switched off or connection of a USB memory
stick. However, the system memorises these
lists and if they are not modified, the loading
time will be shorter.
Play starts automatically after a period which
depends on the capacity of the USB memory
stick.
Selection of source
The SOURCE button on the steering mounted controls allows a
direct change to the next media source.
"CD / CD MP3"
"RADIO"
"STREAMING"
"USB, iPod"
"AUX"
Press MUSIC to display the "MEDIA"
menu.
Select "Following media source" and
confirm.
Repeat the operation as many times as necessary to obtain the
desired media source (except for radio which is accessible either
with SOURCE or RADIO).
293
08 MUSIC MEDIA PLAYERS
Selecting a track
Previous track.
/
Next track.
/
MUSIC: List of USB or CD tracks or
folders
Up or down in the list.
/
Confirm, next menu level.
/
/
Previous folder.
Next folder.
Fast forward.
Long press
/
/
+
Fast backward.
Pause: long press on SRC.
294
Long press
/
/
Up one menu level.
/
08 MUSIC MEDIA PLAYERS
Connecting APPLE® players
Connect the Apple® player to the USB port using a suitable cable
(not supplied).
Play starts automatically.
Audio streaming
Streaming allows audio files on your telephone to be played via the
vehicle's speakers.
Control is via the audio system.
The classifications available are those of the portable device
connected (artists / albums / genres / playlists / audiobooks /
podcasts).
The default classification used is by artist. To modify the classification
used, return to the first level of the menu then select the desired
classification (playlists for example) and confirm to go down through
the menu to the desired track.
The "Shuffle tracks" mode on an iPod® corresponds to the "Random"
mode on the audio system.
The "Shuffle albums" mode on an iPod® corresponds to the "Random
all" on the audio system.
"Shuffle tracks" is restored by default on each connection.
The version of software in the audio system may not be compatible
with the generation of your Apple® player.
Connect the telephone: see "USING THE TELEPHONE".
Select "Audio" or "All" profile.
If play does not start automatically, it may be necessary to start the
audio playback from the telephone.
Control is from the peripheral device or by using the audio system
buttons.
Once connected in streaming mode, the telephone is considered to be
a media source.
It is recommended that you activate "Repeat" on the Bluetooth
peripheral.
295
08 MUSIC MEDIA PLAYERS
Using the auxiliary input (AUX)
JACK/USB audio cable not supplied
Connect the portable device (MP3, WMA
player…) to the JACK auxiliary audio socket
or USB port using a suitable cable.
Press MUSIC to display the "MUSIC"
menu.
296
Select "Activate / Deactivate AUX
input" and confirm.
First adjust the volume of your portable
device (to a high level). Then adjust the
volume of your audio system.
Display and management of the controls are via the portable device.
09 AUDIO SETTINGS
They are accessible by the MUSIC
button in the control panel or by a long
press on RADIO according to the source
in use.
-
"Equalizer" (choice of 6 musical ambiences)
"Bass"
"Treble"
"Loudness" (Activate/Deactivate)
"Distribution" ("Driver", "All passengers")
"Le-Ri balance" (Left/Right)
"Fr-Re balance" (Front/Rear)
"Auto. Volume" depending on road speed (Activate/Deactivate)
The distribution (or spatialisation using the Arkamys© system) of sound
is an audio process that allows the audio quality to be adapted to the
number of listeners in the vehicle.
The audio settings (Equalizer, Bass, Treble and Loudness) are
different and independent for each sound source.
The settings for distribution and balance are common to all sources.
On-board audio: Arkamys© Sound Staging.
With Sound Staging, the driver and passengers are immersed in an
"audio scene" recreating the natural atmosphere of an auditorium:
truly a part of the scene and its surroundings.
This new sensation is made possible by software in the audio system
which processes the digital signals from the media players (radio,
CD, MP3…) without changing the audio settings. This processing
takes account of the characteristics of the passenger compartment to
produce optimum results.
The Arkamys© software installed in your audio system processes
the digital signal from the media players (radio, CD, MP3, ...) and
recreates a natural musical scene, with harmonious placement of
instruments and voices in the space in front of passengers, level with
the windscreen.
297
10 CONFIGURATION
Display configuration
298
Press SETUP to display the
"Configuration" menu.
Select "Choose colour" and confirm to
select the screen colour harmony and
the map presentation mode:
day mode,
night mode,
automatic day/night mode,
according to whether the
headlamps are on.
Select "Display configuration" and
confirm.
Select "Adjust luminosity" and confirm
to adjust the screen brightness.
Press "OK" to save the changes.
The settings for day and night are
independent.
11 SCREEN MENU MAP(S)
MAIN FUNCTION
1
2
3
1
3
Option A
2
Option A1
2
Option A11
2
Option B...
"Navigation - guidance"
MENU
2
2
Chosen destination
2
3
3
3
3
3
Directory
3
GPS coordinates
Add a stage
Enter an address
Directory
3
3
2
2
2
3
Define calculation criteria
2
Enter an address
Journey leg and route
1
3
Guidance options
Select destination
2
2
Divert route
1
2
Fastest route
2
Shortest route
2
Distance/Time
With tolls
With Ferry
Traffic info
Set speech synthesis
Delete last destinations
Set parameters for risk areas
Map management
1
Order/delete journey legs
3
1
Previous destinations
2
Map orientation
Vehicle direction
North direction
Perspective view
Map details
Move the map
Mapping and updating
Description of risk areas database
Stop / Restore guidance
1
2
2
2
2
2
2
Fastest route
Shortest route
Distance/Time
With tolls
With Ferry
Traffic info
299
11 SCREEN MENU MAP(S)
"TRAFFIC INFORMATION"
MENU
2
Retain the messages:
2
3
3
2
2
2
1
On the route
Manual TMC
List of TMC stations
1
Directory of contacts
3
3
300
3
2
3
3
Synchronization options
2
3
Dial
3
Import all the entries
2
1
3
Delete all contacts
2
"TELEPHONE" MENU
3
Sort by First name/Name
2
2
No synchronization
Display telephone contacts
Display SIM card contacts
Display all phone contacts
Contact mem. status
List of the paired peripherals
2
New contact
2
Automatic TMC
Display / Do not display
messages
Bluetooth functions
1
Contacts management
1
Delete calls log
2
Cancel
2
Around the vehicle
Select TMC station
1
Delete
2
Ring options
2
Import
2
Retain all the messages:
Phone functions
1
Open
2
Geographic filter
1
Call
2
2
1
Connect
Disconnect
Delete
Delete all
Cancel
Peripherals search
Rename radiotelephone
Hang up
11 SCREEN MENU MAP(S)
"RADIO" MENU
1
2
Change Waveband
2
AM / FM
2
Guidance options
1
2
2
1
2
Bass
2
Treble
Loudness
3
RDS options
3
Audio settings
3
2
Equalizer
3
3
3
3
3
3
None
2
Classical
2
3
Jazz
Rock
Techno
Vocal
1
Change Media
1
2
Activated / Deactivated
2
Distribution
2
TA
"MUSIC" MENU
Driver
2
All passengers
2
Le-Ri balance
Fr-Re balance
2
Auto. Volume
2
2
Update radio list
2
1
1
Bluetooth streaming
USB/iPod
AUX
Read mode
1
Activated / Deactivated
CD
Normal
Random
Random on all media
Repetition
Audio settings
Activate / Deactivate AUX
input
301
11 SCREEN MENU MAP(S)
"SETUP" MENU
1
2
Display configuration
2
Choose colour
2
3
3
4
4
4
2
2
2
Harmony:
2
Cartography:
2
Day mode
Night mode
Auto Day/Night
Adjust luminosity
Set date and time
Select units
Speech synthesis setting
1
2
2
Select language
1
2
2
2
2
2
2
Define vehicle parameters*
1
Français
Parking assistance
2
English
Wiper operation
2
Italiano
3
Portuguese
Lighting configuration
2
Español
3
Deutsch
3
Nederlands
3
Turkish
3
Polski
Rear wiper in reverse
Guide-me-home lighting time
Directional headlamps
Mood lighting
Daytime running lamps
Trip computer
1
Русский
2
2
Alert log
Status of functions
Guidance instructions volume
Select male voice/Select female voice
* The settings vary according to the vehicle.
302
FREQUENTLY ASKED QUESTIONS
The following table groups together the answers to the most frequently asked questions concerning your audio system.
QUESTION
ANSWER
SOLUTION
The route calculation is
not successful.
The guidance criteria may conflict with the current location (exclusion of
toll roads on a toll motorway).
Check the guidance criteria on the Navigation
Menu, "Guidance options"\ "Define calculation
criteria".
I am unable to enter my
post code.
The system only accepts post codes of up to 5 characters.
The POIs do not appear.
The POIs have not been selected.
Select the POIs in the list of POIs.
The risk areas audible
warning does not work.
The audible warning is not active.
Activate audible warnings in the Guidance options
menu, "Navigation - guidance", "Set parameters
for risk areas".
The system does not
suggest a detour around
an incident on the route.
The guidance criteria do not take account of TMC messages.
Select the "Traffic info" function in the list of
guidance criteria.
I receive a Risk area alert
which is not on my route.
Other than guidance, the system announces all Risk areas positioned in a
cone located in front of the vehicle. It may provide an alert for a Risk area
located on nearby or parallel roads.
Zoom in on the map to view the exact position of
the Risk area. Select "On the route" to no longer
receive alerts other than guidance or to reduce the
time for the announcement.
303
FREQUENTLY ASKED QUESTIONS
QUESTION
Certain traffic jams
along the route are not
indicated in real time.
The altitude is not
displayed.
I am unable to connect
my Bluetooth telephone.
The volume of the
telephone connected
in Bluetooth mode is
inaudible.
304
ANSWER
SOLUTION
On starting, it is several minutes before the system begins to receive the
traffic information.
Wait until the traffic information is being received
correctly (display of the traffic information icons on
the map).
The filters are too restrictive.
Modify the "Geographic filter" settings.
In certain countries, only major routes (motorways...) are listed for the
traffic information.
This phenomenon is normal. The system is
dependent on the traffic information available.
On starting, the initialisation of the GPS may take up to 3 minutes to
receive more than 4 satellites correctly.
Wait until the system has started up completely.
Check that there is a GPS coverage of at least
4 satellites (long press on the SETUP button, then
select "GPS coverage").
Depending on the geographical environment (tunnel...) or the weather,
the conditions of reception of the GPS signal may vary.
This phenomenon is normal. The system
is dependent on the GPS signal reception
conditions.
The telephone's Bluetooth function may be switched off or the telephone
may not be visible.
-
The Bluetooth telephone is not compatible with the system.
You can check the compatibility of your telephone
on www.peugeot.co.uk (services)
The volume depends both on the system and on the telephone.
Increase the volume of the audio system, to
maximum if required, and increase the volume of
the telephone if necessary.
The ambient noise level has an influence on the quality of telephone
communication.
Reduce the ambient noise level (close the windows,
reduce the booster fan speed, slow down, ...).
-
Check that your telephone's Bluetooth
function is switched on.
Check in the telephone settings that it is
"visible to all".
FREQUENTLY ASKED QUESTIONS
QUESTION
ANSWER
SOLUTION
Some contacts are
duplicated in the list.
The options for synchronizing contacts are synchronizing the contacts
on the SIM card, the contacts on the telephone, or both. When both
synchronizations are selected, some contacts may be duplicated.
Select "Display SIM card contacts" or "Display
telephone contacts".
Contacts are not shown
in alphabetical order.
Some telephones offer display options. Depending on the settings
chosen, contacts can be transferred in a specific order.
Modify the display setting in the telephone
directory.
The system does not receive
SMS text messages.
The Bluetooth mode does not permit sending SMS text messages to the
system.
The CD is ejected
automatically or is not
played by the player.
The CD is inserted upside down, is unplayable, does not contain any
audio data or contains an audio format which the player cannot play.
The CD has been recorded in a format that is not compatible with the
player (udf, ...).
The CD is protected by an anti-pirating protection system which is not
recognised by the audio system.
-
Check that the CD is inserted in the player the right
way up.
Check the condition of the CD: the CD cannot be
played if it is too damaged.
Check the content in the case of a recorded CD:
refer to the information and advice in the "MUSIC
MEDIA PLAYERS" section.
The audio system's CD player does not play DVDs.
Some recorded CDs will not be played by the audio
system because they are not of the correct quality.
There is a long waiting
period following the insertion
of a CD or connection of a
USB memory stick.
When a new medium is inserted, the system reads a certain amount of
data (directory, title, artist, etc.). This may take from a few seconds to a
few minutes.
This phenomenon is normal.
The CD player sound is
poor.
The CD used is scratched or of poor quality.
Insert good quality CDs and store them in suitable
conditions.
The audio equipment settings (bass, treble, ambiences) are unsuitable.
Set the treble or bass level to 0, without selecting
an ambience.
305
FREQUENTLY ASKED QUESTIONS
QUESTION
ANSWER
SOLUTION
Some characters in the
media information are not
displayed correctly while
playing.
The audio system does not display some types of characters.
Use standard characters to name tracks and
folders.
Playing of streaming files
does not start.
The peripheral device connected does not support automatic play.
Start the playback from the device.
The names of tracks and
the track length are not
displayed on the screen
when streaming audio.
The Bluetooth profile does not allow the transfer of this information.
The quality of reception
of the radio station
listened to gradually
deteriorates or the stored
stations do not function
(no sound, 87.5 Mhz is
displayed...).
The vehicle is too far from the transmitter used by the station listened
to or there is no transmitter in the geographical area through which the
vehicle is travelling.
Activate the "RDS" function by means of the
short-cut menu to enable the system to check
whether there is a more powerful transmitter in the
geographical area.
The environment (hills, buildings, tunnels, basement car parks...) block
reception, including in RDS mode.
This phenomenon is normal and does not indicate
a fault with the audio system.
The aerial is absent or has been damaged (for example when going
through a car wash or into an underground car park).
Have the aerial checked by a PEUGEOT dealer.
I cannot find some radio
stations in the list of
stations received.
The name of the radio
station changes.
306
The station is not received or its name has changed in the list.
Some radio stations send other information in place of their name (the
title of the song for example).
The system interprets this information as the name of the station.
FREQUENTLY ASKED QUESTIONS
QUESTION
In changing the setting
of treble and bass the
equalizer setting is
deselected.
ANSWER
SOLUTION
The selection of an equalizer setting imposes the balance settings.
Modifying one without the other is not possible.
Modify the balance or equalizer settings to obtain
the desired musical ambience.
The selection of a distribution setting imposes the balance settings.
Modifying one without the other is not possible.
Modify the balance or distribution settings to
obtain the desired musical ambience.
For optimum sound quality, the audio settings for Volume, Bass, Treble,
Equalizer and Loudness can be adapted to the different sound sources,
which may result in audible differences when changing source (radio,
CD...).
Check that the audio settings for (Volume, Bass,
Treble, Equalizer, Loudness) are adapted to
the sources listened to. It is advisable to set the
AUDIO functions (Bass, Treble, Fr-Re balance,
Le-Ri balance) to the middle position, select the
"None", musical ambience and set the loudness
correction to the "Active" position in CD mode or
to the "Inactive" position in radio mode.
In changing the equalizer
setting, treble and bass
return to zero.
When changing the
balance settings, the
distribution setting is
deselected.
When changing an
distribution setting,
the balance setting is
deselected.
There is a difference in
sound quality between
the different audio
sources (radio, CD...).
307
FREQUENTLY ASKED QUESTIONS
QUESTION
ANSWER
With the engine off, the
system switches off after
a few minutes of use.
When the engine is switched off, the system's operating time depends on
the battery charge.
The switch-off is normal: the system switches to economy mode and
switches off to prevent discharging of the vehicle's battery.
Start the vehicle's engine to increase the battery
charge.
Playback of my USB
memory stick starts only
after a very long wait
(around 2 to 3 minutes).
Some files supplied with the memory stick may greatly slow down access
to reading the memory stick (multiplication by 10 of the catalogue time).
Delete the files supplied with the memory stick
and limit the number of sub-folders in the file
structure on the memory stick.
When I connect my
iPhone as telephone and
to the USB port at the
same time, I am unable
to play the music files.
When the iPhone connects automatically as a telephone, it forces the
streaming function. The streaming function takes the place of the USB
function which is then not useable, there is a period without sound of the
track being played with Apple® players.
Disconnect and reconnect to the USB port (the
USB function takes priority over streaming).
When I connect my
Apple® player or my
BlackBerry® to the
USB port, I have alert
messages on the current
consumption by the USB
port.
When charging, the current consumption of these smartphones is greater
than the rating of the USB port, which is 500mA.
308
SOLUTION
PEUGEOT Connect Sound (RD5)
AUDIO SYSTEM / BLUETOOTH®
CONTENTS
Your PEUGEOT Connect Sound (RD5) is coded in such
a way that it will only operate in your vehicle.
For safety reasons, the driver must only carry out
operations which require prolonged attention while the
vehicle is stationary.
When the engine is switched off and to prevent
discharging of the battery, the audio equipment may
switch off after a few minutes.
01 First steps
02 Steering mounted controls
03 Main menu
04 Audio
05 PEUGEOT Connect USB
06 Bluetooth
07 Screen menu map(s)
Frequently asked questions
p.
p.
p.
p.
p.
p.
p.
p.
310
311
312
313
317
320
323
326
309
01 FIRST STEPS
Select source:
radio, audio CD / MP3 CD, USB,
Jack connection, Streaming,
AUX.
Selection of AM / FM / DAB*
wavebands.
* Depending on model.
Audio settings: front/
rear fader, left/right
balance, bass/treble,
loudness, audio
ambiences.
Display the list of
local stations.
Long press: CD
tracks or MP3
folders (CD / USB).
Abandon the current
operation.
TA (Traffic Announcements)
on/off.
Long press: PTY* (radio
Programme TYpe) mode.
Eject CD.
* Available according to version.
Select the screen display
mode:
Date, audio functions, trip
computer, telephone.
Automatic frequency search
down/up.
Select previous/next CD, MP3
or USB track.
On/off, volume setting.
Confirm.
The DARK button changes the screen display
for improved driving comfort at night.
1st press: upper bar only illuminated.
2nd press: black screen.
3rd press: return to standard display.
310
Buttons 1 to 6:
Select a pre-set radio station.
Long press: pre-set a station.
Display main menu.
Select next frequency down/up.
Select previous/next MP3 folder.
Select previous/next folder / genre /
artist / playlist (USB).
02 STEERING MOUNTED CONTROLS
Radio: automatic search for a higher frequency.
CD / MP3 / USB: selection of the next track.
CD / USB: continuous press: fast forwards play.
Move in the list.
Radio: select the previous/next pre-set
station.
USB: select genre / artist / folder from the
classification list.
Select the previous/next item in a menu.
Change audio source.
Confirm a selection.
Call/end call on the telephone.
Press for more than 2 seconds:
telephone main menu.
Radio: automatic search for a lower
frequency.
CD / MP3 / USB: selection of the
previous track.
CD / USB: continuous press: fast
reverse.
Move in the list.
Volume increase.
Volume decrease.
Mute: press the volume
increase and decrease
buttons simultaneously.
The sound is restored
by pressing one of the
two volume buttons.
311
03 MAIN MENU
Screen C
AUDIO FUNCTIONS:
radio, CD, USB, options.
VEHICLE DIAGNOSTICS:
alert log.
TELEPHONE:
hands-free kit, pairing,
management of a call.
PERSONALISATIONCONFIGURATION:
vehicle parameters,
display, languages.
For a detailed global view of the
menus available, refer to "Screen
menu map" in this section.
312
04 AUDIO
Radio
Selecting a station
Press the SOURCE button several
times in succession and select the
radio.
Press the BAND AST button to select
a waveband: FM1, FM2, FMast, AM.
Briefly press one of the buttons to
carry out an automatic search of the
radio stations.
Press one of the buttons to carry out
a manual search up / down for radio
frequencies.
Press the LIST REFRESH button to
display the list of stations received
locally (30 stations maximum).
To update this list, press for more
than two seconds.
The external environment (hills, buildings, tunnels, basement car parks, ...) may
block reception, including in RDS mode. This is a normal effect of the way in which
radio waves are transmitted and does not indicate any failure of the audio system.
RDS
Press the MENU button.
Select AUDIO FUNCTIONS then
press OK.
Select the FM WAVEBAND
PREFERENCES function then
press OK.
Select ACTIVATE RDS then press
OK. RDS appears on the screen.
In radio mode, press OK directly to activate / deactivate RDS
mode.
The RDS, if displayed, enables you to continue listening to the same
station by automatic retuning to alternative frequencies. However, in certain
conditions, coverage of an RDS station may not be assured throughout the
country as radio stations do not cover 100 % of the territory. Under conditions
of very weak reception, the system may change to a regional station.
313
04 AUDIO
Receiving TA messages
The TA (Traffic Announcement) function gives priority to TA alert
messages. To operate, this function needs good reception of a
radio station transmitting this type of message. When a traffic
report is transmitted, the current audio source (Radio, CD, ...) is
interrupted automatically to play the TA message. Normal playback
of the audio source resumes at the end of the transmission of the
message.
DAB (Digital Audio Broadcasting)
Digital radio
Digital radio provides a superior audio quality and also additional
categories of traffic announcements (TA INFO).
The different "multiplex services" offer a choice of radio stations in
alphabetical order.
Change band (FM1, FM2, DAB, ...)
Press the TA button to activate or
deactivate traffic messages.
Change of station within the same "multiplex service".
Start a search for the next "multiplex service".
Long press: select the desired categories of
announcements from Transport, News, Entertainment
and Flash special (availability according to the station).
When the radio station is displayed in the screen, press on "OK" to
display the contextual menu.
(Frequency hopping (RDS), DAB / FM auto tracking, RadioText
(TXT) display, Information on the station, ...)
314
04 AUDIO
Digital radio - DAB / FM tracking
"DAB" does not have 100% coverage of the country.
When the digital signal is weak, "DAB / FM auto tracking" allows you
to continue listening to the same station, by automatically switching
to the corresponding analogue "FM" station (if it exists).
CD
Playing a CD
Insert circular compact discs only.
Some anti-pirating systems, on original discs or CDs copied using a
personal recorder, may cause faults which are no reflection on the
quality of the vehicle's player.
Without pressing the EJECT button, insert a CD in the player, play
begins automatically.
Press the "Menu" button.
Select "Multimedia" and confirm.
To play a disc which has already been
inserted, press the SOURCE button
several times in succession and
select CD.
Select "DAB / FM auto tracking" and confirm
Press one of the buttons to select a
track on the CD.
If "DAB / FM auto tracking" is on, there will be a difference of a few
seconds in the programme when the system changes to analogue
"FM" radio, with sometimes a variation in volume.
When the strength of the digital signal is good again, the system
automatically switches back to "DAB"
If the "DAB" station you are listening to is not available on "FM"
("DAB/FM" option barred), or if "DAB / FM auto tracking" is not on,
the sound will be cut when the digital signal is too weak.
Press the LIST REFRESH button to display the list of tracks
on the CD.
Press and hold one of the buttons for
fast forwards or fast backwards.
315
04 AUDIO
MP3 CD
Playing an MP3 compilation
MP3 CD
Information and advice
Insert an MP3 compilation in the player.
The audio equipment searches for all of the music tracks, which
may take anything between a few seconds and several tens of
seconds, before play begins.
The MP3 format, an abbreviation of MPEG 1.2 & 2.5 Audio Layer 3,
is an audio compression standard which permits the recording of
several tens of music files on a single disc.
On a single disc, the CD player can read up to 255 MP3 files
spread over 8 folder levels. However, it is advisable to keep to
a limit of two levels to reduce the access time before the CD is
played.
While the CD is being played, the folder structure is not followed.
All of the files are displayed on a single level.
To play a disc which has already
been inserted, press the SOURCE
button several times in succession
and select CD.
Press one of the buttons to select a
folder on the CD.
Press one of the buttons to select a
track on the CD.
Press the LIST REFRESH button to display the list of directories of
the MP3 compilation.
Press and hold one of the buttons for
fast forward or backward play.
316
In order to be able to play a recorded CDR or CDRW, when
recording, the ISO 9660 level 1.2 or Joliet file format is
recommended.
If the disc is recorded in another format, it may not be played
correctly.
It is recommended that the same recording format is always used
for an individual disc, with as low a speed as possible
(4x maximum) for optimum sound quality.
In the particular case of a multi-session CD, the Joliet format is
recommended.
The audio system will only play files with the extension ".mp3" with
a sampling rate of 22.05 KHz or 44.1 KHz. No other type of file
(.wma, .mp4, .m3u...) can be played.
It is advisable to restrict file names to 20 characters without using
special characters (e.g. " ? ; ù) to avoid any playing or displaying
problems.
Empty CDs are not recognised and may damage the system.
05 PEUGEOT CONNECT USB
Using the PEUGEOT CONNECT USB
Connecting a USB memory stick
This unit consists of a USB port and an auxiliary
Jack socket*. The audio files are transmitted
from a portable device - digital player or a USB
memory stick - to your PEUGEOT Connect
Sound (RD5) and heard via the vehicle's
speakers.
USB memory stick (1.1, 1.2 and 2.0) or Apple®
player of generation 5 or later:
USB memory sticks should be formatted
FAT or FAT 32 (NTFS not supported),
the Apple® player lead is essential,
navigation through the file database is also
possible by means of the steering mounted
controls.
Other Apple® players of earlier generations and
players using the MTP protocol*:
play via Jack-Jack lead only (not supplied),
navigation through the file database is from
the portable device.
Connect the memory stick to the port, directly or
using a lead. If the audio equipment is switched
on, the USB source is detected as soon as it
is connected. Play begins automatically after a
delay which depends on the capacity of the
USB memory stick.
The file formats supported are .mp3 (mpeg1
layer 3 only) and .wma (standard 9 only,
128 kbits/sec compression).
Certain playlist formats are supported (.m3u, ...)
On reconnection of the previous memory stick
used, play is resumed automatically with the last
track played.
The system puts together playlists (temporary memory) created
over a period which depends on the capacity of the USB device.
The other sources are available during this time.
The playlists are updated each time the ignition is switched off or
each time a USB memory stick is connected.
When connecting for the first time, the classification suggested
is by folder. When you reconnect, the classification selected
previously is retained.
* According to vehicle.
317
05 PEUGEOT CONNECT USB
Using the PEUGEOT CONNECT USB
Press and hold LIST to display the
different classifications.
Select by Folder / Artist / Genre / Playlist,
press OK to select the classification
required, then press OK again to confirm.
-
by Folder: all folders containing audio
files recognised on the peripheral
device.
by Artist: all of the artist names
defined in the ID3 Tags, classified in
alphabetical order.
by Genre: all of the genres defined in
the ID3 Tags.
by Playlist: in accordance with the
playlists recorded on the USB device.
Press one of these buttons to gain
access to the previous / next track on
the classification list currently being
played.
Press and hold one of the buttons for
fast forward or backward play.
Press one of these buttons to
gain access to the previous / next
Genre, Folder, Artist or Playlist on
the classification list currently being
played.
Connecting an Apple® player via the USB port
The lists available are Artist, Genre and Playlist (as defined in
the Apple® player).
Selection and Navigation are described in steps 1 to 4 above.
Press LIST briefly to display the
previously selected classification.
Navigate through the list using the left/
right and up/down buttons.
Confirm the selection by pressing OK.
318
Do not connect a hard disk or USB connection device other
than audio equipment to the USB port. This could damage your
installation.
05 PEUGEOT CONNECT USB
Using the auxiliary input (AUX)
JACK socket or USB port (according to vehicle)
Adjusting the volume of the auxiliary source
The auxiliary input, JACK or USB, allows the connection of a
portable device (MP3 player...).
First adjust the volume of your portable device.
Do not connect a device to both the JACK socket and the USB
port at the same time.
Connect the portable device (MP3 player…)
to the JACK socket or to the USB port,
using a suitable cable (not supplied).
Press the SOURCE button several
times in succession and select AUX.
Then adjust the volume of your audio
system.
The display and control is via the portable device.
319
06 BLUETOOTH
Bluetooth telephone
Screen C
(Available according to model and version)
Pairing a telephone / First connection
The first 4 telephones recognised are displayed in this window.
For safety reasons and because they require prolonged attention
on the part of the driver, the operations for pairing of the Bluetooth
mobile telephone with the Bluetooth hands-free system of your
audio equipment must be carried out with the vehicle stationary
and the ignition on.
The TELEPHONE menu permits access to the following functions
in particular: Directory*, Call list, Pairing management.
Go to www.peugeot.co.uk for more information (compatibility,
more help, ...).
Select the telephone to be connected from the list. Only one
telephone can be connected at a time.
Activate the telephone's Bluetooth function
and ensure that it is "visible to all" (telephone
configuration.
A virtual keypad is displayed in the
screen: enter a code with at least 4 digits.
Confirm by pressing OK.
Press the MENU button.
In the menu, select:
Bluetooth telephone function Audio
Bluetooth configuration
Perform a Bluetooth search
A window is displayed with a message that a search is in progress.
320
The services offered depend on the network, the SIM card and the
compatibility of the Bluetooth equipment used.
Consult your telephone's manual and your operator to find out which
services are available to you.
* If your telephone is fully compatible.
A message is displayed in the screen of the
telephone chosen. To accept the pairing, enter the
same code on the telephone, then confirm with OK.
If pairing fails, the number of attempts is not limited.
A message that the pairing has been successful appears in the
screen.
The automatic connection authorised is only active after the
telephone has been configured.
The directory and the call list can be accessed after the
synchronisation period.
06 BLUETOOTH
Receiving a call
An incoming call is announced by a ring and a superimposed
display in the vehicle's screen.
Select the YES tab on the display
using the buttons and confirm by
pressing OK.
Press this button to accept the call.
Making a call
From the Bluetooth telephone function Audio menu, select Manage
the telephone call then Call, Call list or Directory.
Press this button for more than two seconds for
access to your directory, then navigate with the
thumb wheel.
Or
To dial a number, use your telephone's keypad,
with the vehicle stationary.
The system accesses the telephone's contacts directory, depending
on compatibility, and while the Bluetooth connection with it is
maintained.
With certain telephones connected by Bluetooth you can send a
contact to the directory of the audio system.
Contacts imported in this way are saved in a permanent directory
visible to all, whatever the telephone connected.
The menu for the directory is not accessible if it is empty.
321
06 BLUETOOTH
Bluetooth audio streaming*
Ending a call
During a call, press this button for more than
2 seconds.
Confirm with OK to end the call.
Wireless transmission of music files on the telephone, played via
the audio equipment. The telephone must be able to manage the
appropriate Bluetooth profiles (Profiles A2DP / AVRCP).
Initiate the pairing between the telephone and
the vehicle. This pairing can be initiated from
the vehicle's telephone function menu or via the
telephone's keypad. Refer to the steps in "Pairing
a telephone" on the previous pages. During the
pairing phase, the vehicle must be stationary with
the key in the ignition.
Select the telephone to be connected from the telephone function
menu.
The audio system connects to a newly paired telephone automatically.
Activate the streaming source by
pressing the SOURCE button**.
The tracks to be played can be
controlled as usual via the buttons on
the audio system control panel and
the steering mounted controls***.
The contextual information can be
displayed on the screen.
* Depending on the compatibility of the telephone.
** In certain cases, playing of the Audio files must be initiated from the
keypad.
*** If the telephone supports the function.
322
07 SCREEN MENU MAP(S)
Screen C
Press the OK dial for access to short-cut menus according
to the display in the screen:
RADIO
1
1
1
activate / deactivate RDS
1
activate / deactivate REG mode
activate / deactivate radiotext
1
1
CD / MP3 CD
USB
activate / deactivate Intro
activate / deactivate track repeat (of the
current folder / artist / genre / playlist)
activate / deactivate track repeat (the
entire current CD for CD, the entire
current folder for MP3 CD)
activate / deactivate random play (the
entire current CD for CD, the entire
current folder for MP3 CD)
1
activate / deactivate random play (of the
current folder / artist / genre / playlist)
1
323
07 SCREEN MENU MAP(S)
Screen C
Audio functions
1
FM waveband settings
2
Alternative frequencies (RDS)
3
4
Regional mode (REG)
3
4
activate / deactivate
Radio-text information (RDTXT)
3
4
activate / deactivate
Play modes
2
3
4
3
4
324
activate / deactivate
Album repeat (RPT)
activate / deactivate
Track random play (RDM)
activate / deactivate
Pressing the MENU button displays:
1
2
Vehicle diagnostics
Alert log
07 SCREEN MENU MAP(S)
Personalisation-Configuration
1
Define the vehicle settings*
2
Display configuration
2
Video brightness adjustment
3
4
4
4
Bluetooth configuration
2
Connect/Disconnect an equipment
3
Telephone function
3
normal video
Audio Streaming function
3
inverse video
4
brightness (- +) adjustment
4
Date and time adjustment
3
4
4
4
4
day/month/year adjustment
hour/minute adjustment
choice of 12 h / 24 h mode
4
4
l/100 km - mpg - km/l
°Celsius / °Fahrenheit
Choice of language
Consult the paired equipment
Delete a paired equipment
Perform a Bluetooth search
Call
2
Calls list
3
4
Choice of units
3
2
Bluetooth telephone
1
2
3
3
Directory
Manage the telephone call
Terminate the current call
Activate secret mode
* The parameters vary according to vehicle.
325
FREQUENTLY ASKED QUESTIONS
QUESTION
ANSWER
SOLUTION
There is a difference in
sound quality between
the different audio
sources (radio, CD...).
For optimum sound quality, the audio settings (Volume, Bass, Treble,
Ambience, Loudness) can be adapted to the different sound sources,
which may result in audible differences when changing source (radio,
CD...).
Check that the audio settings (Volume, Bass,
Treble, Ambience, Loudness) are adapted to
the sources listened to. It is advisable to set
the AUDIO functions (Bass, Treble, Front-Rear
Balance, Left-Right Balance) to the middle
position, select the musical ambience "None" and
set the loudness correction to the "Active" position
in CD mode or to the "Inactive" position in radio
mode.
The CD is ejected
automatically or is not
played by the player.
The CD is inserted upside down, is unplayable, does not contain any
audio data or contains an audio format which the player cannot play.
The CD is protected by an anti-pirating protection system which is not
recognised by the audio equipment.
-
The message "USB
peripheral error" is
displayed on the screen.
The Bluetooth connection
is cut.
326
Check that the CD is inserted in the player the
right way up.
Check the condition of the CD: the CD cannot
be played if it is too damaged.
Check the content in the case of a recorded
CD: consult the advice in the "Audio" section.
The audio equipment's CD player does not
play DVDs.
Due to their quality level, certain writeable
CDs will not be played by the audio system.
The battery of the peripheral may not be sufficiently charged.
Recharge the battery of the peripheral device.
The USB memory stick is not recognised.
The memory stick may be corrupt.
Reformat the memory stick.
FREQUENTLY ASKED QUESTIONS
QUESTION
ANSWER
SOLUTION
I am unable to access my
voicemail.
Few telephones or service providers allow the use of this function.
The CD player sound is
poor.
The CD used is scratched or of poor quality.
Insert good quality CDs and store them in suitable
conditions.
The audio equipment settings (bass, treble, ambiences) are unsuitable.
Set the treble or bass level to 0, without selecting
an ambience.
The stored stations do
not function (no sound,
87.5 Mhz is displayed...).
An incorrect waveband is selected.
Press the BAND AST button to return to the
waveband (AM, FM1, FM2, FMAST) on which the
stations are stored.
The traffic announcement
(TA) is displayed. I do
not receive any traffic
information.
The radio station is not part of the regional traffic information network.
Tune to a radio station which broadcasts traffic
information.
The quality of reception
of the radio station
listened to gradually
deteriorates or the stored
stations do not function
(no sound, 87.5 Mhz is
displayed...).
The vehicle is too far from the transmitter used by the station listened
to or there is no transmitter in the geographical area through which the
vehicle is travelling.
Activate the RDS function to enable the system
to check whether there is a more powerful
transmitter in the geographical area.
The environment (hills, buildings, tunnels, basement car parks...) block
reception, including in RDS mode.
This phenomenon is normal and does not indicate
a failure of the audio equipment.
The aerial is absent or has been damaged (for example when going
through a car wash or into an underground car park).
Have the aerial checked by a PEUGEOT dealer.
327
FREQUENTLY ASKED QUESTIONS
QUESTION
ANSWER
SOLUTION
Sound cut-outs of 1 to
2 seconds in radio mode.
During this brief sound cut-out, the RDS searches for any frequency
permitting better reception of the station.
Deactivate the RDS function if the phenomenon is
too frequent and always on the same route.
With the engine off,
the audio equipment
switches off after a few
minutes of use.
When the engine is switched off, the audio equipment operating time
depends on the battery charge.
The switch-off is normal: the audio equipment switches to economy mode
and switches off to prevent discharging of the vehicle's battery.
Start the vehicle's engine to increase the battery
charge.
The message "the audio
system is overheated"
appears on the display.
In order to protect the installation if the surrounding temperature is too
high, the audio equipment switches to an automatic thermal protection
mode leading to a reduction of the volume or stopping of the playing of
the CD.
Switch the audio system off for a few minutes to
allow the system to cool.
328
ALPHABETICAL INDEX
Accessories ..................................... 199
Accessory socket, 12V ...................... 83
Access to rear seats .......................... 72
Active bonnet ................................... 106
Adjusting headlamps ......................... 95
Adjusting the steering wheel.............. 68
Airbags .............................................113
Airbags, front ............................ 114, 117
Airbags, lateral.......................... 115, 117
Air conditioning .................................. 20
Air conditioning, automatic .......... 74, 75
Air filter ............................................ 159
Air flow ............................................... 20
Air vents............................................. 73
Alarm ................................................. 55
Alert / warning log .............................. 46
Alloy wheels..................................... 198
Anti-lock braking system (ABS) ....... 103
Anti-pinch........................................... 58
Anti-theft .......................................... 129
Arches, aluminium ........................... 197
Armrest, front ..................................... 84
Ashtray .............................................. 83
Assistance call ................. 102, 207, 208
Audible warning ............................... 102
Audio streaming (Bluetooth) .... 295, 322
Audio systems ..................................211
Audio/video sockets......................... 238
Automatic illumination
of headlamps ............................ 90, 93
Automatic operation of hazard
warning lamps............................... 101
A/ Automatic rain sensitive windscreen
wipers ....................................... 97, 99
Auxiliary
sockets............ 85, 238, 286, 317, 319
B/ Battery ..................................... 159, 176
Battery, charging.............................. 177
Battery, remote control ................ 53, 54
Bluetooth
(hands-free) .................. 239, 277, 320
Bluetooth (telephone) ...... 239, 277, 320
Bodywork ......................................... 197
Bonnet ............................................. 152
Boot ................................................... 63
Boot lamp .......................................... 88
Boot (opening) ................................... 51
Brake discs ...................................... 160
Brake lamps............................. 181, 184
Brake pads ...................................... 160
Braking assistance system .............. 103
C/ Capacity, fuel tank ........................... 150
CD MP3 ........................... 234, 292, 316
Central locking ............................. 52, 61
Changing a bulb ....................... 178-185
C/ Changing a fuse ....................... 186-192
Changing a wheel ..................... 168-172
Changing a wiper blade ........... 100, 174
Changing the remote control battery.... 53
Changing the time ........... 38, 45, 47, 49
CHECK .............................................. 37
Checking levels ........................ 156-158
Checking the engine oil level ..... 33, 156
Checking tyre pressures
(using the kit) ................................ 167
Checks...................................... 153-160
Children .....................112, 118, 124-128
Child seats ............................... 118-128
Cleaning (advice)............................. 197
Clock.................................................. 38
Closing the boot........................... 52, 63
Closing the doors......................... 52, 60
Colour screen, retractable ..... 46, 48, 50
Connectors,
audio ............... 85, 238, 286, 317, 319
Coolant level .............................. 33, 158
Coolant temperature indicator ........... 33
Courtesy mirror .................................. 82
Cruise control .................................. 143
Cup holder ......................................... 81
Customising stickers........................ 197
D/ DAB (Digital Audio
Broadcasting)................ 290, 314, 315
Date (setting) ......................... 45, 47, 49
ALPHABETICAL INDEX
A/ ABS and EBFD systems.................. 103
ALPHABETICAL INDEX
330
D/ Daytime running lamps...... 92, 179, 180
Deactivating ESP............................. 105
Deactivating the passenger airbag ...114
Deadlocking ....................................... 52
Defrosting .......................................... 77
Dials and gauges ............................... 22
Diesel additive level ......................... 158
Dimensions ...................................... 205
Dipped beam ..................... 89, 179, 180
Dipstick ...................................... 33, 156
Directional lighting ..................... 96, 197
Direction indicators ... 101, 179, 181, 184
Doors ................................................. 60
Doors emergency control .................. 62
Door trays .......................................... 81
Driving economically ......................... 20
Driving positions (memorising) .......... 67
Dynamic stability control (DSC) ......... 29
E/ EBA
(Emergency braking assistance).... 103
Eco-driving ........................................ 20
Economy mode................................ 175
Electric window controls .................... 58
Electronic brake force distribution
(EBFD) .......................................... 103
Electronic engine immobiliser .... 54, 129
Electronic gearbox system ................ 20
Electronic stability control (ESC) ..... 104
E/ Emergency braking system ............. 103
Emergency call ................. 102, 207-209
Emergency warning lamps .............. 101
Energy economy mode.................... 175
Engine compartment ............... 153, 154
Engine compartment fusebox .......... 190
Engine,
Diesel .................... 151, 154, 155, 203
Engine oil level indicator ............ 33, 156
Engine, petrol .................. 151, 153, 201
Engines.................................... 201, 203
Environment .......... 20, 54, 74, 158, 166
Equipment settings .......... 24, 42, 46, 48
ESC/ASR ......................................... 104
F/ Filling with fuel ......................... 150, 151
Fitting a wheel ................................. 170
Fittings, boot ...................................... 87
Flashing indicators........................... 101
Front seats................................... 64, 65
Fuel............................................ 20, 151
Fuel consumption .............................. 20
Fuel filler flap ................................... 150
Fuel gauge......................................... 22
Fuel tank .......................................... 150
Fusebox, dashboard ........................ 188
Fuses ............................................... 186
G/ Gearbox, automatic ........... 20, 133, 160
Gearbox, manual ............... 20, 132, 160
Gear lever, automatic gearbox ........ 133
Gear lever, manual gearbox ............ 132
Gear shift indicator .......................... 137
Glove box .......................................... 82
G.P.S. ...................................... 222, 261
Guidance ................................. 222, 261
Guide-me-home........................... 93, 94
H/ Halogen headlamps......................... 178
Hands-free kit .................. 240, 278, 320
Hazard warning lamps ..................... 101
Headlamp adjustment........................ 95
Headlamps, directional .............. 96, 179
Headlamp wash ................................. 98
Headlamp wash reservoir ................ 158
Head restraints, rear .......................... 72
Heated seats ..................................... 66
Heating .............................................. 75
Height and reach adjustment,
steering wheel................................. 68
Hill start assist ................................. 131
Horn ................................................. 102
ALPHABETICAL INDEX
Ignition ............................................. 129
Indicators, direction ......................... 101
Inflating accessories
(using the kit) ................................ 167
Inflating tyres ............................. 20, 206
Inputs for audio system .... 85, 238, 296,
317, 319
Instrument panel lighting ................... 38
Instrument panels .................. 22, 24, 37
Instrument panel screen .................... 22
Intelligent Traction Control ............... 104
Interior finish .................................... 197
Interior fittings .................................... 81
Interior lamp....................................... 78
Interior mood lighting ......................... 79
ISOFIX ............................................. 125
ISOFIX child seats .................... 126-127
ISOFIX mountings ........................... 125
J/ JACK socket .............. 85, 296, 317, 319
Jukebox (copy) ................................ 236
Jukebox (playing) ............................ 237
K/ Keeping children
safe ......................... 112, 114, 118-128
Key in ignition warning..................... 129
Key with remote
control ................................ 51-54, 129
L/ Labels, identification ........................ 206
Lamps, front............................. 178, 197
Lamps, rear ..................... 181, 184, 197
Lamps,
warning and indicator................. 26-32
LED daytime running lamps .............. 92
Level, brake fluid ............................. 157
Level, headlamp wash ............... 98, 158
Level, power steering fluid ............... 157
Levels and checks .................... 153-160
Lighting bulbs
(replacement)................................ 178
Lighting control stalk .......................... 89
Lighting dimmer ................................. 38
Lighting, guide-me home ................... 93
Lighting, interior ........................... 78, 79
Lighting on reminder .......................... 91
Loading .............................................. 20
Load reduction mode ....................... 175
Locating your vehicle ......................... 53
Locking from the inside...................... 61
Locking the boot ................................ 63
Low fuel level ............................. 28, 150
M/ Main beam......................... 89, 179, 180
Maintenance ...................................... 20
Maintenance (advice) ...................... 197
Map reading lamps ............................ 78
Markings, identification .................... 206
Mat..................................................... 86
Menu, main ...................................... 312
Mirror, rear view ................................. 71
Mirrors, door ................................ 69, 70
Mountings for ISOFIX seats ............ 125
MP3 CD ........................... 234, 292, 316
Music media players ........ 234, 291, 315
N/ Navigation................................ 222, 261
Number plate lamps ........................ 185
O/ Oil filter ............................................ 159
Oil level ...................................... 33, 156
Opening the bonnet ......................... 152
Opening the boot ......................... 51, 63
Opening the doors ................. 51, 60, 62
Opening the fuel filler flap ................ 150
Opening the retractable
screen ............................................. 50
Operation indicator lamps............. 26-32
ALPHABETICAL INDEX
I/ Identification plates.......................... 206
ALPHABETICAL INDEX
332
P/ Paint colour code............................. 206
Paintwork, matt ................................ 198
Parking brake .......................... 130, 160
Parking sensors, front...................... 147
Parking sensors, rear ...................... 146
Particle emission filter.............. 158, 159
Passenger compartment filter.......... 159
PEUGEOT call button...................... 209
PEUGEOT Connect
Assistance ............................ 208, 209
PEUGEOT Connect Media
Navigation (NG4 3D) ...24, 39, 48, 211
PEUGEOT Connect Navigation
(RT6) ....................................... 46, 255
PEUGEOT Connect SOS ........ 208, 209
PEUGEOT Connect Sound
(RD5) ...................................... 42, 309
PEUGEOT Connect USB .................. 85
PEUGEOT services ......................... 209
PIN code .......................................... 242
Player, CD MP3 ............... 234, 292, 316
POIs (updating) ............................... 229
Port, USB........... 85, 236, 296, 317, 319
Priming the fuel system ................... 155
Protecting children ..... 112, 114, 118-128
Puncture .......................................... 161
R/ Radio ............................... 233, 287, 313
RCA sockets .................... 238, 296, 319
Rear foglamp ..................... 91, 181, 184
Rear screen (demisting) .................... 77
Recharging the battery .................... 177
Reduction of electrical load ............. 175
Regeneration of the particle
emissions filter .............................. 159
Reinitialising the electric windows ..... 59
Reinitialising the remote control ........ 53
Remote control ............................. 51-54
Removing a wheel ........................... 169
Removing the mat ............................. 86
Repair kit, puncture ......................... 161
Replacing bulbs ............................... 178
Replacing fuses ............................... 186
Replacing the air filter ...................... 159
Replacing the oil filter ...................... 159
Replacing the passenger
compartment filter ......................... 159
Replacing wiper blades ........... 100, 174
Resetting the service indicator .......... 36
Resetting the trip recorder ................. 37
Rev counter ....................................... 22
Reversing lamps ...................... 181, 184
Risk areas (update) ................. 229, 267
Routine checks ........................ 159, 160
Running out of fuel (Diesel) ............. 155
S/ Screen, colour ......................... 217, 244
Screen, colour and mapping.... 259, 299
Screen menu map ........... 244, 299, 323
Screen, monochrome .............. 312, 323
Screen, multifunction (with audio
equipment) .................... 42, 46, 48, 50
Screenwash fluid level ............... 98, 158
Screenwash, front.............................. 98
Screen-wash reservoir..................... 158
Seat adjustment........................... 64, 65
Seat belts............................ 29, 110, 112
Seats, electric .............................. 65, 67
Seats, rear ......................................... 72
Serial number, vehicle ..................... 206
Service indicator ................................ 35
Service warning light ......................... 28
Servicing ............................................ 20
Setting the clock .............. 38, 45, 47, 49
Short-cut menus ...................... 218, 260
Sidelamps ............. 89, 92, 179-181, 184
Side repeater ................................... 180
SIM card .......................................... 242
Snow chains .................................... 173
Spare wheel..................................... 171
Speed limiter.................................... 140
Speedometer ..................................... 22
Spoiler, active .................................. 107
Starting the vehicle .................. 129, 133
Steering mounted controls,
audio ..............................216, 258, 311
Stickers, customising ....................... 197
Stopping the vehicle ................ 129, 133
Storage .................................. 81, 84, 87
ALPHABETICAL INDEX
Stowing rings ..................................... 87
Sun visor............................................ 82
Synchronising the remote control ...... 53
Synthesiser, voice............................ 272
System, navigation .................. 222, 261
T/ Traffic information
(TMC) ............................ 231, 275, 276
Trajectory control systems ............... 104
Trip computer .............................. 39, 41
Trip distance recorder ........................ 37
Tyre pressures ................................. 206
Tyres .................................................. 20
Tyre under-inflation detection .......... 138
T/ Table of weights....................... 202, 204
Tables of engines..................... 201, 203
Tables of fuses................................. 186
Tank, fuel ......................................... 150
Technical data........................... 201-206
Telephone ................ 209, 239, 277, 320
Telephone,
hands-free..................... 239, 277, 320
Temperature control
for heated seats .............................. 66
Temperature, coolant ......................... 33
Temporary tyre repair kit .................. 161
Third brake lamp...................... 181, 184
TMC (Traffic info) ..................... 231, 275
Tools ........................................ 168, 171
Total distance recorder ...................... 37
Towbar ............................................. 195
Towed loads............................. 202, 204
Towing another vehicle .................... 193
Traction control (ASR) ............... 29, 104
Traffic information
(TA) ............................... 232, 276, 314
U/ Under floor storage............................ 88
Under-inflation (detection) ............... 138
Unlocking ........................................... 51
Unlocking from the inside .................. 61
Unlocking the boot ....................... 51, 63
Update risk areas .................... 229, 267
Updating POIs ......................... 229, 266
Updating the time ............ 38, 45, 47, 49
USB (PEUGEOT Connect) ........ 85, 317
V/ Vehicle configuration ....... 24, 42, 46, 48
Vehicle diagnosis ............................... 42
Vehicle identification ........................ 206
Ventilation .................................... 73, 74
Voice commands ............................. 214
W/ Warning lamps.............................. 26-32
Washing (advice) ............................. 197
Weights.................................... 202, 204
Welcome lighting ......................... 79, 80
Window controls ................................ 58
Wiper control stalk ....................... 97, 99
Wipers ......................................... 97, 99
X/ Xenon headlamps............................ 179
ALPHABETICAL INDEX
S/ Storing driving positions .................... 67
EXTERIOR
334
Remote control key
51-54
- opening / closing
- unlocking / partial opening of the boot
- anti-theft protection
- battery
Alarm
55-57
Boot
Temporary puncture
repair kit
Changing a wheel
Active spoiler
Accessories
199-200
Active bonnet
Lighting controls
Directional lighting
Headlamp height adjustment
Changing bulbs
- front lamps
- direction indicator repeaters
63
161-167
168-172
107-108
Parking sensors
Towbar
Towing
146-148
195-196
193-194
Changing bulbs
- rear lamps
- 3rd stop lamp
- number plate lamps
181-185
Wipers
Changing a wiper blade
Door mirrors
Doors
- opening / closing
- central locking
- anti-attack security
- emergency locking
Cleaning, maintenance
Alarm
Electric windows
Fuel tank
150-151
Braking assistance
Trajectory control
Tyre under-inflation detection
Tyre pressures
Snow chains
97-100
174
69-70
106
89-94
96
95
178-181
60-62
197-198
55-57
58-59
103
104-105
138-139
138, 167, 206
173
INTERIOR
Front seats
Rear seats
Child seats
ISOFIX child seats
Airbags
113-117
Steering lock / Starting / Ignition switch
129
87-88
118-124, 128
125-127, 128
Seat belts
110-112
Deactivating the passenger's
front airbag
Interior fittings
- sun visor
- glove box
- 12 V accessory socket
- ashtray
- front armrest
- PEUGEOT Connect USB
- mat
114-115
81-86
VISUAL SEARCH
Boot fittings
- stowing rings
- storage net
- storage box
- lighting
64-67
72
336
INSTRUMENTS AND CONTROLS
Instrument panels
Warning lamps
Indicators
Buttons
- Check / service indicator /
trip distance recorder
- lighting dimmer
22-25
26-32
33-36
37-38
Lighting controls
Headlamp height adjustment
89-94
95
Steering wheel adjustment
Horn
Door mirrors
Electric windows
Dashboard fuses
Opening the bonnet
Speed limiter
Cruise control
Courtesy lamps
Seat belt / passenger's front airbag
warning lamps display
Rear view mirror
Sun visor
78
110-111
71
82
Wiper controls
Trip computer
Multifunction screens
Clock
Hazard warning lamps
Switch panel
42-50
38
101
15
PEUGEOT Connect Media Navigation (NG4 3D) 211-254
PEUGEOT Connect Navigation (RT6) 255-308
PEUGEOT Connect Sound (RD5)
309-328
Emergency or assistance call
102, 207
68
102
69-70
58-59
Ventilation
Dual zone digital air conditioning
186-189
152
140-142
143-145
97-100
39-41
Parking brake
Active spoiler control
130
107-108
Automatic gearbox
Manual gearbox
Gear shift indicator
Hill start assist
73-74
75-77
133-136
132
137
131
TECHNICAL DATA - MAINTENANCE
155
201
202
203
204
205
206
Energy economy mode
Battery
Checking levels
156-158
- oil
- brake fluid
- power steering fluid
- coolant
- screenwash/headlamp wash fluid
- additive (Diesel with particle emissions filter)
- used products
Changing bulbs
- front
- rear
178-185
Cleaning and maintenance
- interior
- exterior
197-198
Engine compartment
fuses
Opening the bonnet
Under the bonnet, petrol
Under the bonnet, Diesel
152
153
154
175
176-177
186-187, 190-192
Checking components
159-160
- battery
- air filter and passenger compartment filter
- oil filter
- particle emission filter (Diesel)
- gearboxes
- brake pads / discs
VISUAL SEARCH
Running out of fuel, Diesel
Petrol engines
Petrol weights
Diesel engine
Diesel weights
Dimensions
Identification markings
This guide presents all of the equipment
available.
Your vehicle will be fitted with some of the
equipment described in this document
depending on the version and the specific
requirements for the country in which it is
sold.
The descriptions and illustrations are
given without any obligation. Automobiles
PEUGEOT reserves the right to modify the
technical specifications, equipment and
accessories without having to update the
current guide.
This document is an integral part of your
vehicle. It should be passed on to the new
user in the event of sale or transfer.
Automobiles PEUGEOT declares, by
application of the provisions of the
European regulation (Directive 2000/53)
relating to End of Life Vehicles, that
it achieves the objectives set by this
regulation and that recycled materials are
used in the manufacture of the products
that it sells.
For any work on your vehicle, use a
qualified workshop that has the technical
information, competence and equipment
required, which a PEUGEOT dealer is able
to provide.
Reproduction or translation of all or part of
this handbook is prohibited without written
authorisation from Automobiles PEUGEOT.
Printed in the EU
Anglais
Design by
09-13
Anglais
www.peugeot.com
AN. 14RCZ.0040

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement