M O Model 4200 Owner`s Guide

SVMASTER - - http://www.msvmaster.lv



For a period of one calendar year from the date of purchase of this auto-security device, Directed Electronics, Inc. promises to the ORIGINAL PURCHASER to repair or replace (with a comparable reconditioned model), free of cost, any electronic control module which proves to be defective in workmanship or material under normal use,

SO LONG AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A PROFESSIONAL

AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY

INSTALLED. If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the following page.

After the first calendar year, from the date of purchase of this auto-security device,

Directed Electronics, Inc., promises to the ORIGINAL PURCHASER to repair or replace

(with a comparable reconditioned model) any electronic control module which proves to be defective in workmanship or material under normal use FFO R A AR

$ 45 0,, SO LONG AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A PRO-

FESSIONAL AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS

ORIGINALLY INSTALLED. If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the following page.

This warranty contains the entire agreement relating to warranty and supersedes all previous and contemporaneous representations or understandings, whether written or oral. IN ANY EVENT, DIRECTED ELECTRONICS, INC. IS NOT LIABLE FOR THE THEFT OF

THE VEHICLE AND/OR ITS CONTENTS.

This warranty is void if the product has been damaged by accident, unreasonable use, neglect, improper service or other causes not arising out of defects in materials or construction. This warranty is nontransferable and does not apply to any unit that has been modified or used in a manner contrary to its intended purpose and does not cover batteries. The unit in question must be returned to the manufacturer, postage prepaid. This warranty does not cover labor costs for the removal, diagnosis, troubleshooting or reinstallation of the unit. For service on an out-of-warranty product a flat rate fee by model is charged. Contact your authorized dealer to obtain the service charge for your unit.

These systems are a deterrent against possible theft. Directed Electronics, Inc. is not offering a guarantee or insuring against the theft of the automobile or its contents and disclaims any liability for the theft of the vehicle and/or its contents. Directed

Electronics does not authorize any person to create for it any other obligation or liability in connection with this security system.

©

2005 Directed Electronics—all rights reserved

SVMASTER - ii

- http://www.msvmaster.lv


TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUD-

ED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COM-

MERCE THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLU-

SION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WAR-

RANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL WARRANTY OF

NON-INFRINGEMENT OF PATENTS, IN THE UNITED STATES OF AMERICA AND/OR

ABROAD. NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED THEREWITH

SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT

NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, TOWING,

REPAIR, REPLACEMENT, DAMAGES FOR LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL

LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE

ABOVE, MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR

THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

IIM PO RTTA NTT N

This product warranty is automatically void if its date code or serial number is defaced, missing, or altered. This warranty will not be valid unless you have completed the warranty card and mailed it to Directed Electronics, Inc. within 10 days after purchase to the address listed on the warranty registration card.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

■ Date of purchase

■ Your full name and address

■ Authorized dealer's company name and address

■ Type of system installed

■ Year, make, model and color of the automobile

■ Automobile license number

■ Vehicle identification number

■ All security options installed on automobile

■ Installation receipts

SVMASTER - iiii


©



mee CCo nssu

SSttaan daarrd nffiig urraattiio 2

W haatt iiss IIn deed

IIm po maattiio 3

System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Your Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

FCC/ID Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 nccttiio 5

Standard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 g Y ou

Warning! Safety First. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Disabling the Starter Kill Without a Transmitter . . . . . . . . . . . . . . . . . . . . . . . 10

Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Remote Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Rear Defogger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Valet Take-Over . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Short-Run/Turbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Timer Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Starter Anti-Grind Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Disabling the Remote Start System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Reessu mee LLo giicc.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1 8 grraam miin g O pttiio nss.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1 8

CCo nvveen mss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2 0 nssiio nss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2

N otteess .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2

Q uiicckk R nccee G uiid 5


SVMASTER -

©



ntt M od ™and an A uxxiilliiaarryy O uttp utt.

2

SVMASTER -

+ controls TTiim meerr mode.

+ controls TTu urrb o//SSh orrtt R n.

+ controls CCh haan 4 output.

+ + controls R

©




■ The control module

■ An HX receiver/antenna

■ Two four-button transmitters

■ The red status LED indicator light

■ A push-button Valet button

■ Your warranty registration

■ A shut-down toggle switch

Congratulations on the purchase of your remote start keyless entry system. Due to the complexity of this system, it must be installed by an authorized dealer only. Installation of this product by anyone other than an authorized dealer voids the warranty. All dealers are provided with a preprinted dealer certificate to verify that they are authorized.

By carefully reading this Owner's Guide prior to using your system, you will maximize the use of this system and its features.

You can print additional or replacement copies of this manual by accessing the Directed Electronics internet website at

www.directed.com

.

©




The system requires no specific maintenance. Your remote is powered by a small, lightweight 3-volt lithium battery that will last approximately one year under normal use. When the battery begins to weaken, operating range will be reduced and the LED on the remote will dim.

Y ou

Your warranty registration must be completely filled out and returned within 10 days of purchase. Your product warranty will not be validated if your warranty registration is not returned.

Make sure you receive the warranty registration from your dealer.

It is also necessary to keep your proof of purchase, which reflects that the product was installed by an authorized dealer.

This device complies with Part 15 of FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device.

uttiio n

This product is designed for fuel injected, automatic transmission vehicles only. Use of this product in a standard transmission vehicle is dangerous and contrary to the product's intended use.

SVMASTER -

©




The receiver uses a computer-based learn routine to learn the transmitter buttons. This makes it possible to assign any specific transmitter button, or combination of buttons, to any receiver function. The transmitter initially comes programmed with the

Standard Configuration, but may also be customized by an authorized dealer. The transmitter buttons indicated in all of the instructions in this manual correspond to a Standard Configuration transmitter.

urraattiio n

B utttto

The arming and panic functions are controlled by pressing on the transmitter for one second.

B utttto

The disarm function is controlled by pressing mitter for one second.

on the trans-

B utttto

Silent Mode ™ and an optional auxiliary function are controlled by pressing . Silent Mode works by pressing for less than one second. An optional auxiliary function, such as trunk release, is controlled by pressing and holding

1.5 seconds.

for

©



SVMASTER -

B utttto

The remote start function of your system is controlled by pressing this button twice within 3 seconds.

and Buttons


An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously.

The auxiliary output controls __________________________.

B on

+ +

When simultaneously pressed these buttons control the rear window defogger during remote starting.

The following safety warnings must be observed at all times:

■ Due to the complexity of this system, installation of this product must only be performed by an authorized Directed

Electronics dealer.

■ When properly installed, this system can start the vehicle via a command signal from the remote control transmitter.

Therefore, never operate the system in an enclosed area or

SVMASTER -

©




partially enclosed area without ventilation (such as a garage).

When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user's sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle.

O R A OU

R M USSTT IIN

VIIN G A

A CCA

A A

RB

DJJA

MO NO DEETTEECCTTO N

D OO RSS LLEEA DIIN G FFR OM

D O R P RTTIIA

VIIN G A

OR AG A

M USSTT A the sole responsibility of the user.

■ Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user must also have the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed

Electronics dealer in accordance with the Safety Check outlined in the product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the authorized Directed Electronics dealer to fix the problem.

©




■ After the remote start module has been installed, contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the product installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or the installer must properly reinstall the remote start system so that the vehicle does not start in gear. All installations must be performed by an authorized Directed

Electronics dealer. O PEER ATTIIO

HIICCLLEE SSTTA RTTSS IIN

N O

GEEA R IISS CCO

REEM OTTEE SSTTA RTT M OD

NTTR AR NTTEEN D--

D M OD

M U ND

OFF O PEER ATTIIO N.. O PEER ATTIIN

HEESSEE CCO ND NSS M AY

D AM GEE O

REEM OTTEE SSTTA

N P

ON ALL IIN RY OU USSTT IIM

RO

A UTTH RIIZZEED

ON NEECCTT TTH

NIITT A ND

RO NIICCSS D

D EELLEECCTTR ON

ATTIIO N O

WIILLLL N OTT B REESSP ON

ATTIIO OSSTTSS..

ASSSSIISSTTA NCCEE O

REEP AIIR R

REEM OTTEE SSTTA RTT M OD

BLLEE O R P Y FFO miin g

Pressing for one second arms the system by activating the starter kill and locking the doors (if the door locks are connected).

The horn will honk (if connected) and the parking lights will flash once to confirm arming of the system. While the system is armed, the status LED will flash once per second. The Failsafe ® Starter Kill

(if installed) will also prevent the vehicle’s starter from cranking.

SVMASTER -

©




The system can also be programmed to arm the optional Failsafe ®

Starter Kill automatically (called Passive Mode). If the system has been programmed for Passive Mode, the Failsafe ® Starter Kill will automatically activate 30 seconds after the ignition has been turned off. After the ignition has been turned off, the status LED will flash rapidly to indicate that the system is in Passive Mode.

If Passive Mode has been programmed on, then it is also possible to program the system for Passive Locking. With Passive Locking, the vehicle doors lock automatically at the same time that the Failsafe

®

Starter Kill is activated. If Passive Locking is programmed on, care must be taken to prevent the keys from being locked in the vehicle.

N OTTEE:: For Passive Mode to be effective, the Failsafe

® must be installed.

Starter Kill relay

Pressing for one second disarms the system and unlocks the doors (if connected). The horn will honk twice (if connected) and the parking lights will flash twice to confirm disarming of the system. The optional Failsafe ® Starter Kill will be deactivated. The status LED will turn off, unless the system is programmed for Passive

Mode. In Passive Mode, the status LED will flash rapidly when the system is disarmed. This indicates that the system will re-engage the starter kill and re-lock the doors (if Passive Locking has been programmed) in 30 seconds unless the ignition is turned on.

©



SVMASTER -

Wiitth ou


If your remote transmitter is lost or damaged, you can manually override the starter kill. To do this, you must have the vehicle's ignition key and know where the Valet button is located. Be sure to check with the installer for the location of the Valet button.

To override the starter kill, turn the ignition on and press the

Valet button within 10 seconds.

The status LED will stop flashing

DRW-35 and the vehicle should start. If it does not start, you may have waited too long; turn the ignition off and repeat the process.

ATTIIO N O ALLEETT B UTTTTO N_____________________________

You can prevent your system from automatically activating the

Failsafe ® Starter Kill and locking the doors by using Valet Mode.

This is very useful when washing the vehicle or having it serviced.

In Valet Mode, the starter kill cannot be activated, even with the transmitter, but all convenience functions (door locks, remote start, etc.) will continue to work normally.

SVMASTER -

©


SVMASTER -

Mo dee::

1. Turn the ignition on.

2. Turn the ignition off.

3. Press and release the Valet button within 10 seconds.


DRW-35

The status LED will light steadily if you are entering Valet Mode and will turn off if you are exiting Valet Mode.

niicc M dee

If you are threatened in or near your vehicle, you can attract attention by triggering the system with your transmitter. Just press for 1.5 seconds to enter Panic Mode. In Panic Mode, the horn will honk and the parking lights will flash for 30 seconds. To stop Panic Mode at any time, press transmitter.

, or on the

N OTTEE:: In order for Panic Mode to be effective, the vehicle’s horn (or optional siren) as well as the vehicle's parking lights must be connected.

SVMASTER -

©



1 1


Reem ottee SSttaarrtt

This feature allows you to remotely start and run your vehicle for a programmable period of time. This makes it possible to warm up the engine, as well as adjust the interior temperature of the vehicle with the climate control system. If interior heating or cooling is desired, the climate controls must be preset, and the fan blower must be set to the desired level prior to remote starting the vehicle.

IIM PO RTTA NTT!! (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the key in the ignition. o rreem hee vveeh

1.

Press the button twice within 3 seconds on the transmitter.

2.

The parking lights will flash to confirm that the vehicle will attempt to start.

3.

Release the button as soon as the parking lights flash.

(In gasoline vehicles, the engine will start 4 seconds after the parking lights flash. In diesel vehicles, the engine will start when the WAIT-TO-START indicator on the vehicle's dash goes out or the timer has expired.)

4.

Once the vehicle has started, it will run for the pre-programmed period of time (12, 24, or 60 minutes) or until a shutdown input is triggered.


©


SVMASTER -

W heen dyy tto

1. Insert the ignition key and turn it to the ON (not the

START) position.

2. Press the brake pedal.


N OTTEE:: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.

While the vehicle is running during remote start operation, the system will monitor the vehicle and will automatically shut down the engine if the system receives any of the following shut-down inputs:

■ The brake pedal is pressed.

■ The hood is opened.

■ The shutdown toggle switch is put into the OFF position.

■ The pre-programmed run time (12, 24, or 60 minutes) has elapsed.

■ Transmitter button is pressed twice in 3 seconds to start the vehicle.

Deeffo geerr

To turn the rear defogger output OFF:

1.

Simultaneously press & release the on the remote control.

+ + buttons

2.

The lights will flash 2 times.

3.

The rear defogger output will no longer activate when the vehicle is remote started.

SVMASTER -

N OTTEE:: If the remote start is on the parking lights will turn off then flash

2-times before returning to their normal output and the defogger output, if active, will cease.

©



1 3

SVMASTER -

To turn the rear defogger output ON:


1.

Simultaneously press & release the on the remote control.

+ + buttons

2.

The lights will flash 3 times.

3.

The rear defogger output will once again activate when the vehicle is remote started.

N OTTEE:: If the remote start is on the lights will turn off then flash 3-times before returning to their normal output and the defogger output will activate as programmed.

The Valet Take-Over feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate controls on.

1. Before turning off the engine, press and release on the transmitter twice in 3 seconds (or press and release the optional momentary switch).

2. Turn the ignition key to the OFF position. (The engine will stay running.)

3. Once the vehicle has started, it will run for the pre-programmed period of time (12, 24, or 60 minutes) or until a shutdown input is triggered.


©


SVMASTER -

SSh orrtt--R urrb o


Short-run turbo mode keeps the engine running after arriving at you destination for a programmable period of 1, 3 ,5 or 10 minutes. This allows the system’s timer to conveniently cool down the turbo after you have left the vehicle.

To activate:

1.

Park the vehicle and set parking brake.

2.

Remove your foot from the brake pedal and leave the engine running.

3.

Press and release the and buttons at the same time.

4.

The lights will flash to indicate the remote start has entered short run turbo mode.

5.

Turn off the key, the engine will keep running.

6.

Exit and secure the vehicle.

7.

The engine will turn off after the programmed run time.

By pressing the remote and buttons the parking lights will flash 4 times and then start the vehicle and run for the set duration. The remote start can be shut off by the transmitter by pressing the remote start button and remain in timer mode, but if any other shut down zones or the ignition becomes active the timer mode will cancel.

SVMASTER -

©



1 5

SVMASTER -

1.

Press Timer mode buttons.


2.

The vehicle will confirm with 4 parking light flashes.

3.

A 1-second delay will start.

4.

The system will start the car and will run for the specified duration, unless shut down by the remote start button

. If shut down with the remote start button will remain in timer mode.

the system

5.

The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires.

important!!

Timer Mode should be used only in open areas. Never start and run the vehicle in an enclosed space such as a garage or carport.

To exit timer mode, turn the ignition switch on any time the engine is running. The parking lights will flash 4 times, indicating timer mode has been exited.

5.

The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires.

IIM PO RTTA NTT!! Timer Mode should be used only in open areas. Never start and run the vehicle in an enclosed space such as a garage or carport.


©


SVMASTER -

SSttaarrtteerr A nttii--G


Whenever the vehicle is remote started, advanced anti-grind circuitry prevents the starter from engaging, even if the key is turned to the start position. This prevents damage to the starter motor if the key is turned to the start position during remote start operation.

N OTTEE:: Anti-grind circuitry only works when the remote start system is operating the motor and the Failsafe ® Starter Kill relay is installed.

blliin g tth Reem m

This feature allows your system's remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the shutdown toggle switch to the OFF position. The switch can be installed in a location of your choice. Check with your installer for recommended locations.

ATTIIO N O DO WN

SVMASTER -

©



1 7


This Directed Electronics system will store its current state to nonvolatile memory. If power is lost and then reconnected the system will recall the stored state from memory. This means if the unit is in Valet Mode and the battery is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet Mode. This applies to all states of the system including arm, disarm, and Valet Mode.

Programming options control your system's normal, operational set-up. Most options do not require additional parts, but some may require additional installation labor. This system's programming options are listed below, with the factory default settings in b d:

■ 1122,, 24, or 60 minute run time. your system can be programmed to allow the vehicle to run for 12, 24, or 60 minutes when remote started.

■ 3, 6, 9, or 1122 minute timer mode run time. Your system can be programmed to allow the vehicle to run for 3, 6, 9, or 12 minutes when remote started in timer mode. Can be set up to

16 minutes by your installer.


©



■ Comfort closure is a programming option which closes the vehicle’s windows after remote locking.

■ Parking lights ffllaasshhiinngg or constant. Your system can be programmed to either flash or to turn on the parking lights constantly during the entire remote start operation.

■ Passive Mode or AAccttiivvee M dee. In Passive Mode the Failsafe

®

Starter Kill will automatically activate 30 seconds after the ignition has been turned off.

■ Ignition switch-controlled door-locking oonn or off. With this feature on, the doors will lock 3 seconds after the ignition key is turned on, and unlock when the ignition key is turned off.

■ Passive Locking or AAccttiivvee LLoocckkiinngg (doors lock only with the transmitter). With Passive Locking, the vehicle doors lock automatically 30 seconds after the ignition has been turned off. Passive Locking can only be selected when the system has been programmed for Passive Mode.

■ The horn honk confirmations for locking and unlocking can be programmed o n or off. In order for this feature to be programmed on, the horn must be connected to the system.

SVMASTER -

©



1 9


CCo nttrro niitt: The “brain” of your system. Usually hidden underneath the dash area of the vehicle. It houses the microprocessor which monitors your vehicle and controls all system functions.

FFaaiillssaaffee tem which prevents the vehicle’s starter from cranking whenever the system is armed. The vehicle is never prevented from cranking when the system is disarmed, in Valet Mode, or if the starter kill switch itself fails. Your system has feature-ready circuitry for the starter kill, however installation may require additional labor. vehicle. It is used to indicate the status of your system.

ous functions of your system.

Vaalleett B utttto location inside the vehicle. It is used to override the Failsafe ®

Starter Kill when a transmitter is lost or damaged, or to enter or exit Valet Mode.


©



Listed below are some of the many expansion options available for use with your system. Some options may require additional parts and/or labor. Please consult with your dealer for a complete list of options available for use with this system.

D om onds each time the system is disarmed using the transmitter. This is useful for seeing inside the vehicle at night prior to entering it. htt SSu peerrvviissiio

Po weerr D orr LLo oll:: Your system is capable of controlling many types of power door lock systems; however, some door lock systems may require extra parts. Consult with your dealer to determine which type of locks your vehicle uses. If power locks are connected, the system can be programmed to lock the doors automatically 30 seconds after the ignition has been turned off. The system can also be programmed to lock the doors when the ignition is turned on and to unlock them when the ignition is turned off.

Po weerr TTrru grammed to operate a factory power release for the vehicle's trunk or hatch. If the factory release is not power-activated, Directed

Electronics 522T trunk-release solenoid can often be added.

SVMASTER -

©



2 1


Po weerr W nd ow oll:: Power window control is provided with

Directed Electronics 529T or 530T systems. The 529T system will roll up two windows automatically when the system is armed, or roll two windows down by using the transmitter. The 530T will roll two windows both up and down. The 530T also provides one touch switch operation.

Prro grreessssiivvee D orr U nllo g:: For added security, your system can be configured to unlock the driver’s door only, leaving the passenger doors locked. Pressing the unlock button an additional time will unlock the passenger doors. This option requires additional parts and labor.

A uxxiilliiaarryy O uttp uttss LLiin Reem ottee SSttaarrtt:: For added convenience the auxiliary outputs can be used to position the driver’s seat to a preset position on an Arm, Disarm, or Remote Start command from the remote.


©


SVMASTER -

✂


g yyo urr rreem

■ To arm the system press for one second. The doors will lock (if connected). The LED will begin to flash. The vehicle’s horn (if connected) will honk and the parking lights will flash once to confirm arming.

g yyo urr rreem

■ To disarm the system press for one second. The doors will unlock (if connected). The vehicle’s horn (if connected) will honk twice and the parking lights will flash twice.

hee FFaaiillssaaffee

® wiitth ou

■ Turn on the ignition. Press and release the Valet button within 10 seconds. The LED will stop flashing and the vehicle should start.

o rreem ottee ssttaarrtt tth

■ Press twice within 3 seconds. The parking lights will turn on (if connected) and the vehicle will start and run for the programmed duration.

Vaalleett M dee

■ Turn the ignition to the "ON" position. Turn the ignition back off. Press and release the Valet button within 10 seconds. The status LED will light steadily if you have entered Valet Mode. To exit Valet Mode, repeat the steps above. The LED will turn off when exiting Valet Mode.

niicc M dee

■ Press and hold for 1.5 seconds.

meerr M dee

■ Press and to start the vehicle, and run it for the set duration. urrb o M dee

■ Park the vehicle and set parking brake. Remove your foot from the brake pedal and leave the engine running. Press and release the and buttons.

hee rreem m

■ To disable the remote start, move the shutdown toggle switch to the OFF position. occaattiio n o do wn wiittcch __ __ __ __ __ __ __ __ __ __ _

✂

©


SVMASTER -

2 5



✂

■ Press and release on the transmitter twice in 3 seconds. Turn the ignition key to the OFF position. Once the vehicle has started, it will run for the pre-programmed period of time (12, 24, or 60 minutes).

Wiin do

■ Press the

Deeffo geerr

, and buttons simultaneously to turn the defogger on or off when remote starting. When a remote start is initiated, the parking lights will flash 2-times if the defogger is set to off, and will flash 3-times if the defogger is set to on.

SVMASTER -

✂


M O Model 4200 Owner`s Guide

www.directed.com

To activate:

IIM PO RTTA NTT!! Timer Mode should be used only in open areas. Never start and run the vehicle in an enclosed space such as a garage or carport.

Related manuals

Viper

120HV

Autopage

C3-RS-730 LCD

Autopage

C3-RS-1000 OLED

Autopage

C3-RS-915 LCD

Autopage

Car-Pro CPX-3600

Baretta Security Systems

Advantage