RUGGEDCOM RSG2300

Add to my manuals
46 Pages

advertisement

RUGGEDCOM RSG2300 | Manualzz

RUGGEDCOM RSG2300

Installation Guide

Preface

Introduction

Installing Device

Communication Ports

Technical Specifications

Dimension Drawings

Certification

1

2

3

4

5

6

3/2015

RC1046-EN-05

RUGGEDCOM RSG2300

Installation Guide ii

Copyright © 2015 Siemens Canada Ltd.

All rights reserved. Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or trademark registration.

This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of Siemens Canada Ltd..

Disclaimer Of Liability

Siemens has verified the contents of this manual against the hardware and/or software described. However, deviations between the product and the documentation may exist.

Siemens shall not be liable for any errors or omissions contained herein or for consequential damages in connection with the furnishing, performance, or use of this material.

The information given in this document is reviewed regularly and any necessary corrections will be included in subsequent editions. We appreciate any suggested improvements. We reserve the right to make technical improvements without notice.

Registered Trademarks

ROX™, Rugged Operating System On Linux™, CrossBow™ and ELAN™ are trademarks of Siemens Canada Ltd. ROS® is a registered trademark of Siemens Canada Ltd.

Other designations in this manual might be trademarks whose use by third parties for their own purposes would infringe the rights of the owner.

Third Party Copyrights

Siemens recognizes the following third party copyrights:

• Copyright © 2004 GoAhead Software, Inc. All Rights Reserved.

Security Information

Siemens provides products and solutions with industrial security functions that support the secure operation of plants, machines, equipment and/or networks. They are important components in a holistic industrial security concept. With this in mind, Siemens ' products and solutions undergo continuous development. Siemens recommends strongly that you regularly check for product updates.

For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept) and integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also be considered. For more information about industrial security, visit http://www.siemens.com/industrialsecurity .

To stay informed about product updates as they occur, sign up for a product-specific newsletter. For more information, visit http:// support.automation.siemens.com

.

Warranty

Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. The warranties set forth in this article are exclusive and are in lieu of all other warranties, performance guarantees and conditions whether written or oral, statutory, express or implied (including all warranties and conditions of merchantability and fitness for a particular purpose, and all warranties and conditions arising from course of dealing or usage or trade). Correction of nonconformities in the manner and for the period of time provided above shall constitute the Seller’s sole liability and the Customer’s exclusive remedy for defective or nonconforming goods or services whether claims of the Customer are based in contract (including fundamental breach), in tort (including negligence and strict liability) or otherwise.

For warranty details, visit www.siemens.com/ruggedcom or contact a Siemens customer service representative.

Contacting Siemens

Address

Siemens Canada Ltd.

Industry Sector

300 Applewood Crescent

Concord, Ontario

Canada, L4K 5C7

Telephone

Toll-free: 1 888 264 0006

Tel: +1 905 856 5288

Fax: +1 905 856 1995

E-mail

[email protected]

Web

www.siemens.com/ruggedcom

RUGGEDCOM RSG2300

Installation Guide Table of Contents

Table of Contents

Preface ................................................................................................................

v

Alerts .................................................................................................................................................. v

Related Documents ............................................................................................................................. v

Accessing Documentation .................................................................................................................... v

Training .............................................................................................................................................. vi

Customer Support .............................................................................................................................. vi

Chapter 1

Introduction ..........................................................................................................

1

1.1 Feature Highlights ........................................................................................................................ 1

1.2 Ports, Controls and Indicator LEDs ............................................................................................... 2

Chapter 2

Installing Device ..................................................................................................

5

2.1 Mounting the Device .................................................................................................................... 5

2.1.1 Mounting the Device to a Rack .......................................................................................... 6

2.1.2 Mounting the Device on a DIN Rail .................................................................................... 7

2.1.3 Mounting the Device to a Panel ......................................................................................... 7

2.2 Connecting Power ........................................................................................................................ 8

2.2.1 Connecting AC Power ....................................................................................................... 9

2.2.2 Connecting DC Power ..................................................................................................... 10

2.2.3 Wiring Examples ............................................................................................................. 12

2.3 Connecting the Failsafe Alarm Relay ........................................................................................... 14

2.4 Grounding the Device ................................................................................................................. 15

2.5 Connecting to the Device ........................................................................................................... 15

2.6 Cabling Recommendations ......................................................................................................... 16

2.6.1 Protection On Twisted-Pair Data Ports .............................................................................. 17

2.6.2 Gigabit Ethernet 1000Base-TX Cabling Recommendations ................................................. 17

Chapter 3

Communication Ports .........................................................................................

19

3.1 Copper Ethernet Ports ................................................................................................................ 20

3.2 Fiber Optic Ethernet Ports .......................................................................................................... 21

3.3 SFP Optic Ethernet Ports ........................................................................................................... 21

3.3.1 Installing an SFP Optical Port .......................................................................................... 22

iii

Table of Contents

RUGGEDCOM RSG2300

Installation Guide

3.3.2 Removing an SFP Optical Port ......................................................................................... 23

3.4 GBIC Optic Ethernet Ports .......................................................................................................... 24

3.4.1 Installing a GBIC Optical Port ........................................................................................... 24

3.4.2 Removing a GBIC Optical Port ......................................................................................... 25

Chapter 4

Technical Specifications .....................................................................................

27

4.1 Power Supply Specifications ....................................................................................................... 27

4.2 Failsafe Relay Specifications ...................................................................................................... 27

4.3 Supported Networking Standards ................................................................................................ 28

4.4 Copper Ethernet Port Specifications ............................................................................................ 28

4.4.1 Copper Fast (10/100 Mbps) Ethernet Port Specifications .................................................... 28

4.4.2 Copper Gigabit Ethernet (1 Gbps) Port Specifications ........................................................ 29

4.5 Fiber Optic Ethernet Port Specifications ....................................................................................... 29

4.5.1 10FL Ethernet Optical Specifications ................................................................................ 30

4.5.2 Fast Ethernet (10/100 Mbps) Optical Specifications ........................................................... 30

4.5.3 Gigabit Ethernet (1 Gbps) Optical Specifications ................................................................ 31

4.6 Operating Environment ............................................................................................................... 32

4.7 Mechanical Specifications ........................................................................................................... 32

Chapter 5

Dimension Drawings ..........................................................................................

33

Chapter 6

Certification ........................................................................................................

37

6.1 Agency Approvals ...................................................................................................................... 37

6.2 FCC Compliance ........................................................................................................................ 37

6.3 Industry Canada Compliance ...................................................................................................... 37

6.4 EMI and Environmental Type Tests ............................................................................................. 38

iv

RUGGEDCOM RSG2300

Installation Guide

Preface

Preface

This guide describes the RUGGEDCOM RSG2300. It describes the major features of the device, installation, commissioning and important technical specifications.

It is intended for use by network technical support personnel who are responsible for the installation, commissioning and maintenance of the device. It is also recommended for use by network and system planners, system programmers, and line technicians.

Alerts

The following types of alerts are used when necessary to highlight important information.

DANGER!

DANGER alerts describe imminently hazardous situations that, if not avoided, will result in death or serious injury.

WARNING!

WARNING alerts describe hazardous situations that, if not avoided, may result in serious injury and/or equipment damage.

CAUTION!

CAUTION alerts describe hazardous situations that, if not avoided, may result in equipment damage.

IMPORTANT!

IMPORTANT alerts provide important information that should be known before performing a procedure or step, or using a feature.

NOTE

NOTE alerts provide additional information, such as facts, tips and details.

Related Documents

Other documents that may be of interest include:

• ROS User Guide for the RSG2300

Accessing Documentation

The latest Hardware Installation Guides and Software User Guides for most RUGGEDCOM products are available online at www.siemens.com/ruggedcom .

Alerts v

vi

Preface

RUGGEDCOM RSG2300

Installation Guide

For any questions about the documentation or for assistance finding a specific document, contact a Siemens sales representative.

Training

Siemens offers a wide range of educational services ranging from in-house training of standard courses on networking, Ethernet switches and routers, to on-site customized courses tailored to the customer's needs, experience and application.

Siemens' Educational Services team thrives on providing our customers with the essential practical skills to make sure users have the right knowledge and expertise to understand the various technologies associated with critical communications network infrastructure technologies.

Siemens' unique mix of IT/Telecommunications expertise combined with domain knowledge in the utility, transportation and industrial markets, allows Siemens to provide training specific to the customer's application.

For more information about training services and course availability, visit www.siemens.com/ruggedcom or contact a Siemens sales representative.

Customer Support

Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or general information, contact Siemens Customer Support through any of the following methods:

Online

Visit http://www.siemens.com/automation/support-request to submit a Support Request (SR) or check on the status of an existing SR.

Telephone

Call a local hotline center to submit a Support Request (SR). To locate a local hotline center, visit http:// www.automation.siemens.com/mcms/aspa-db/en/automation-technology/Pages/default.aspx

.

Mobile App

Install the Industry Online Support app by Siemens AG on any Android, Apple iOS or Windows mobile device and be able to:

▪ Access Siemens' extensive library of support documentation, including FAQs, manuals, and much more

▪ Submit SRs or check on the status of an existing SR

▪ Find and contact a local contact person

▪ Ask questions or share knowledge with fellow Siemens customers and the support community

▪ And much more...

Training

RUGGEDCOM RSG2300

Installation Guide

Chapter 1

Introduction

Introduction

The RUGGEDCOM RSG2300 is a rugged, fully managed, modular Ethernet switch specifically designed to operate reliably in electrically harsh and climatically demanding utility substation, railway and industrial environments. The RSG2300’s superior rugged hardware design coupled with the embedded Rugged Operating

System (ROS) provides improved system reliability and advanced cyber security and networking features, making it ideally suited for creating Ethernet networks for mission-critical, real-time, control applications.

The RSG2300 ’s modular flexibility offers 1000BaseX fiber and 10/100/1000BaseTX copper port combinations.

Optional front or rear mount connectors make the RSG2300 highly versatile for any application and can support multiple fiber connectors (SFP, GBIC, LC, SC) without loss of port density. The RSG2300 is packaged in a rugged galvanized steel enclosure with industrial grade DIN, panel, or 48 cm (19 in) rack-mount mounting options.

The RSG2300 P additionally offers 802.3af standard Power over Ethernet (PoE) on up to 4 10/100BaseTx ports.

The RSG2300P is an ideal solution to power and connect several Ethernet devices (such as IP phones, video cameras, and wireless access points) where AC power is not available or cost-prohibitive to provide locally.

The following sections provide more information about the RSG2300:

Section 1.1, “Feature Highlights”

Section 1.2, “Ports, Controls and Indicator LEDs”

Section 1.1

Feature Highlights

Ethernet Ports

• 24 10/100TX copper ports

• Optional: up to 4 1000LX Gigabit Ethernet ports (copper and/or fiber) and up to 8 100FX Fiber Fast Ethernet ports

• Non-blocking, store and forward switching

• 2 port modules for tremendous flexibility

• Fiber types supported include multimode, singlemode, and bidirectional single strand

• Full compliance with IEEE: 802.3, 802.3u & 802.3z

• Full duplex operation and flow control (IEEE 802.3x)

• Fiber optic connectors supported: ST, MTRJ, LC, SC

• Pluggable Optic module support: SFP, GBIC

• Long haul optics allow Gigabit distances up to 90 km

Cyber Security Features

• Multi-level user passwords

• SSH/SSL encryption

• MAC-based port security

• Selective port enable/disable

Feature Highlights 1

2

Chapter 1

Introduction

• Port-based network access control using IEEE 802.1x

• VLAN support (IEEE 802.1Q) to segregate and secure network traffic

• RADIUS centralized access management

• SNMPv3 featuring encrypted authentication and session

Rated for Reliability in Harsh Environments

• Immunity to EMI and heavy electrical transients:

▪ Zero-Packet-Loss™ Technology

▪ Meets IEEE 1613 (electric utility substations)

▪ Exceeds IEC 61850-3 (electric utility substations)

▪ Exceeds IEC 61800-3 (variable speed drive systems)

▪ Exceeds NEMA TS-2 (traffic control equipment)

▪ Exceeds IEC 61000-6-2 (generic industrial environment)

• -40 to 85 °C (-40 to 185 °F) operating temperature (no fans)

• Conformal coated printed circuit boards (optional)

• 18 AWG galvanized steel enclosure

• Hazardous Location Certification: Class 1 Division 2

Universal Power Supply Options

• Fully integrated, dual-redundant (optional) power supplies

• Universal high-voltage range: 88-300 VDC or 85-264 VAC

• Popular low voltage ranges: 24 VDC (12-36 VDC), 48 VDC (36-59 VDC)

• Screw or pluggable terminal blocks for reliable, maintenance-free connections

• CSA/UL 60950-1 safety approved to 85 °C (185 °F)

RUGGEDCOM RSG2300

Installation Guide

Section 1.2

Ports, Controls and Indicator LEDs

The RSG2300 features various ports, controls and indicator LEDs on the front panel for configuring and troubleshooting the device.

Ports, Controls and Indicator LEDs

RUGGEDCOM RSG2300

Installation Guide

Chapter 1

Introduction

4

5

1

2 3 6

Figure 1: Front Panel

1. Port Status Indicator LEDs 2. Display Mode Indicator LEDs 3. Mode Button 4. Alarm Indicator LED 5. Power Module Indicator

LEDs 6. RS232 Serial Console Port (RJ45)

Port Status Indicator LEDs

Display Mode Indicator LEDs

Mode button

Alarm Indicator LED

Power Module Indicator LEDs

RS232 Serial Console Port

These LEDs indicate the state of each port.

When Status mode is selected, these LEDs indicate when ports are active.

• Green (Solid) = Link detected

• Green (Blinking) = Link activity

• Off = No link detected

When Duplex mode is selected, these LEDs indicate when ports are operating in full or half duplex mode.

• Green (Solid) = Full duplex mode

• Orange (Solid) = Half duplex mode

• Off = No link detected

When Speed mode is selected, these LEDs indicate the port speed.

• Green (Solid) = 1000 Mb/s

• Green (Blinking) = 100 Mb/s

• Orange (Solid) = 10 Mb/s

• Off = No link detected

These LEDs indicate the current display mode for the port status indicator LEDs (i.e. Status,

Duplex or Speed).

The Mode button sets the display mode for the port status indicator LEDs (i.e. Status,

Duplex or Speed). It can also be used to reset the device if held for 5 seconds.

The alarm indicator LED illuminates when an alarm condition exists.

These LEDs indicate the status of the power modules.

• Green = The power supply is supplying power

• Red = Power supply failure

• Off = No power supply is installed

This port is for interfacing directly with the device and accessing initial management functions.

Ports, Controls and Indicator LEDs 3

RUGGEDCOM RSG2300

Installation Guide

Chapter 1

Introduction

Ports, Controls and Indicator LEDs 4

RUGGEDCOM RSG2300

Installation Guide

Chapter 2

Installing Device

Installing Device

The following sections describe how to install the device, including mounting the device, installing/removing modules, connecting power, and connecting the device to the network.

DANGER!

Electrocution hazard – risk of serious personal injury and/or damage to equipment. Before performing any maintenance tasks, make sure all power to the device has been disconnected and wait approximately two minutes for any remaining energy to dissipate.

WARNING!

Radiation hazard – risk of serious personal injury. This product contains a laser system and is classified as a CLASS 1 LASER PRODUCT. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

IMPORTANT!

This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void.

Changes or modifications not expressly approved by Siemens Canada Ltd. could invalidate specifications, test results, and agency approvals, and void the user's authority to operate the equipment.

IMPORTANT!

This product should be installed in a restricted access location where access can only be gained by authorized personnel who have been informed of the restrictions and any precautions that must be taken. Access must only be possible through the use of a tool, lock and key, or other means of security, and controlled by the authority responsible for the location.

Section 2.1, “Mounting the Device”

Section 2.2, “Connecting Power”

Section 2.3, “Connecting the Failsafe Alarm Relay”

Section 2.4, “Grounding the Device”

Section 2.5, “Connecting to the Device”

Section 2.6, “Cabling Recommendations”

Section 2.1

Mounting the Device

The RSG2300 is designed for maximum mounting and display flexibility. It can be equipped with connectors that allow it to be installed in a 48 cm (19 in) rack, 35 mm (1.4 in) DIN rail, or directly on a panel.

Mounting the Device 5

Chapter 2

Installing Device

RUGGEDCOM RSG2300

Installation Guide

NOTE

For detailed dimensions of the device with either rack, DIN rail or panel hardware installed, refer to

Chapter 5, Dimension Drawings .

The following sections describe the various methods of mounting the device:

Section 2.1.1, “Mounting the Device to a Rack”

Section 2.1.2, “Mounting the Device on a DIN Rail”

Section 2.1.3, “Mounting the Device to a Panel”

Section 2.1.1

Mounting the Device to a Rack

For rack mount installations, the RSG2300 can be equipped with rack mount adapters pre-installed at the front or rear of the chassis. Additional adapters are provided to further secure the device in high-vibration or seismically active locations.

To secure the device to a standard 48 cm (19 in) rack, do the following:

NOTE

The device can be ordered with the communication ports located at the front or rear of the device.

Placing the ports at the rear allows all data and power cabling to be installed and connected at the rear of the rack.

1. Make sure the rack mount adapters are installed on the correct side of the chassis.

NOTE

The chassis features multiple mounting holes, allowing the rack mount adapters to be installed up to 25 mm (1 in) from the face of the device.

6

1 2

3 3

Figure 2: Rack Mount Adaptors

1. Rear 2. Front 3. Rack Mount Adaptor

2. If required, install adapters on the opposite side of the device to protect from vibrations.

3. Insert the device into the rack.

NOTE

Since heat within the device is channelled to the enclosure, it is recommended that 1 rack-unit of space, or 44 mm (1.75 in), be kept empty above the device. This allows a small amount of convectional airflow.

Forced airflow is not required. However, any increase in airflow will result in a reduction of ambient temperature and improve the long-term reliability of all equipment mounted in the rack space.

Mounting the Device to a Rack

RUGGEDCOM RSG2300

Installation Guide

4. Secure the adapters to the rack using the supplied hardware.

Chapter 2

Installing Device

Section 2.1.2

Mounting the Device on a DIN Rail

For DIN rail installations, the RSG2300 can be equipped with panel/DIN rail adapters pre-installed on each side of the chassis. The adapters allow the device to be slid onto a standard 35 mm (1.4 in) DIN rail.

To mount the device to a DIN rail, do the following:

1. Align the adapters with the DIN rails and slide the device into place.

1

3

2

2

3

Figure 3: DIN Rail Mounting

1. Panel/DIN Rail Adaptor 2. DIN Rail 3. Screw

2. Install one of the supplied screws on either side of the device to secure the adapters to the DIN rails.

Section 2.1.3

Mounting the Device to a Panel

For panel installations, the RSG2300 can be equipped with panel/DIN rail adapters pre-installed on each side of the chassis. The adapters allow the device to be attached to a panel using screws.

To mount the device to a panel, do the following:

1. Place the device against the panel and align the adapters with the mounting holes.

Mounting the Device on a DIN Rail 7

Chapter 2

Installing Device

1

RUGGEDCOM RSG2300

Installation Guide

1 2

8

Figure 4: Panel Mounting

1. Screw 2. Panel/DIN Rail Adaptor

2. Install the supplied screws to secure the adapters to the panel.

Section 2.2

Connecting Power

The RSG2300 supports single or dual redundant AC and/or DC power supplies. The use of two power modules is recommended to provide redundancy and load balancing.

The RSG2300 can be equipped with either a screw-type or pluggable terminal block, which provides power to both power supplies. The screw-type terminal block is installed using Phillips screws and compression plates, allowing either bare wire connections or crimped terminal lugs. Use #6 size ring lugs for secure, reliable connections under severe shock or vibration.

NOTE

• For maximum redundancy in a dual power supply configuration, use two independent power sources.

• Use only #16 gage copper wiring when connecting terminal blocks.

• For 110/230 VAC rated equipment, an appropriately rated AC circuit breaker must be installed.

• For 125/250 VDC rated equipment, an appropriately rated DC circuit breaker must be installed.

• A circuit breaker is not required for 12, 24 or 48 VDC rated power supplies.

Connecting Power

RUGGEDCOM RSG2300

Installation Guide

• It is recommended to provide a separate circuit breaker for each power supply module.

• Equipment must be installed according to applicable local wiring codes and standards.

The following sections describe how to connect power to the device:

Section 2.2.1, “Connecting AC Power”

Section 2.2.2, “Connecting DC Power”

Section 2.2.3, “Wiring Examples”

Chapter 2

Installing Device

Section 2.2.1

Connecting AC Power

To connect a high AC power supply to the device, do the following:

CAUTION!

Electrical hazard – risk of damage to equipment. Do not connect AC power cables to terminals for DC power. Damage to the power supply may occur.

CAUTION!

Electrical hazard – risk of damage to equipment. Before testing the dielectric strength (HIPOT) in the field, remove the metal jumper. This metal jumper connects transient suppression circuitry to chassis ground and must be removed in order to avoid damage to transient suppression circuitry during testing.

NOTE

The terminal block is divided into separate terminals for each internal power supply. Make sure to connect the external power supply to the appropriate terminals.

1. Remove the terminal block cover.

2. If a screw-type terminal block is installed, remove the screws from the appropriate terminals. Use these screws along with #6 ring lugs to secure the wires to the terminal block.

3. Connect the positive wire from the power source to the positive/live (+/L) terminal on the terminal block. For

more information, refer to Section 2.2.3, “Wiring Examples” .

Connecting AC Power 9

Chapter 2

Installing Device

RUGGEDCOM RSG2300

Installation Guide

4

6

5

7

4

6

5

1

3

2

4

6

5

7

4

6

5 3

Figure 5: Terminal Block Wiring

1. Screw-Type Terminal Block 2. Pluggable Terminal Block 3. Jumper 4. Positive/Live (+/L) Terminal 5. Negative/Neutral (-/N)

Terminal (-/N) 6. Surge Ground Terminal 7. Chassis Ground Terminal

4. Connect the negative wire from the power source to the negative/neutral (-/N) terminal on the terminal block.

For more information, refer to Section 2.2.3, “Wiring Examples”

.

5. Install the supplied metal jumper between terminals 2, 4 and 6 to connect the surge ground terminals to the chassis ground terminal. The surge ground terminals are used as the ground conductor for all surge and transient suppression circuitry internal to the unit.

6. Connect the ground terminal on the power source to the chassis ground terminal on the device. For more

information, refer to Section 2.4, “Grounding the Device”

DANGER!

Electrocution hazard – risk of death, serious personal injury and/or damage to the device. Make sure the supplied terminal block cover is always installed before the device is powered.

7. Install the terminal block cover.

Section 2.2.2

Connecting DC Power

To connect a high or low DC power supply to the device, do the following:

CAUTION!

Electrical hazard – risk of damage to equipment. Before testing the dielectric strength (HIPOT) in the field, remove the metal jumper. This metal jumper connects transient suppression circuitry to chassis ground and must be removed in order to avoid damage to transient suppression circuitry during testing.

NOTE

The terminal block is divided into separate terminals for each internal power supply. Make sure to connect the external power supply to the appropriate terminals.

10 Connecting DC Power

RUGGEDCOM RSG2300

Installation Guide

Chapter 2

Installing Device

NOTE

The screw-type terminal block is installed using Philips screws and compression plates, allowing either bare wire connections or crimped terminal lugs. Use #6 size ring lugs for secure, reliable screws, which must be removed to make connections.

1. Remove the terminal block cover.

2. If a screw-type terminal block is installed, remove the screws from the appropriate terminals. Use these screws along with #6 ring lugs to secure the wires to the terminal block.

3. Connect the positive wire from the power source to the positive/live (+/L) terminal on the terminal block. For

more information, refer to Section 2.2.3, “Wiring Examples” .

4

6

5

7

4

6

5

1

3

2

4

6

5

7

4

6

5 3

Figure 6: Terminal Block Wiring

1. Screw-Type Terminal Block 2. Pluggable Terminal Block 3. Jumper 4. Positive/Live (+/L) Terminal 5. Negative/Neutral (-/N)

Terminal (-/N) 6. Surge Ground Terminal 7. Chassis Ground Terminal

4. Connect the negative wire from the power source to the negative/neutral (-/N) terminal on the terminal block.

For more information, refer to Section 2.2.3, “Wiring Examples”

.

5. Install the supplied metal jumper between terminals 2, 4 and 6 to connect the surge ground terminals to the chassis ground terminal. The surge ground terminals are used as the ground conductor for all surge and transient suppression circuitry internal to the unit.

6. Connect the ground terminal on the power source to the chassis ground terminal on the device. For more

information, refer to Section 2.4, “Grounding the Device”

DANGER!

Electrocution hazard – risk of death, serious personal injury and/or damage to the device. Make sure the supplied terminal block cover is always installed before the device is powered.

7. Install the terminal block cover.

Connecting DC Power 11

Chapter 2

Installing Device

Section 2.2.3

Wiring Examples

The following illustrate how to connect power to single and dual power supplies.

RUGGEDCOM RSG2300

Installation Guide

Figure 7: Single AC Power Supply

12

Figure 8: Single DC Power Supply

Wiring Examples

RUGGEDCOM RSG2300

Installation Guide

Figure 9: Dual AC Power Supply

Figure 10: Dual DC Power Supply

Wiring Examples

Chapter 2

Installing Device

13

Chapter 2

Installing Device

RUGGEDCOM RSG2300

Installation Guide

Figure 11: Dual AC/DC Power Supply

Section 2.3

Connecting the Failsafe Alarm Relay

The failsafe relay can be configured to latch based on alarm conditions. The NO (Normally Open) contact is closed when the unit is powered and there are no active alarms. If the device is not powered or if an active alarm is configured, the relay opens the NO contact and closes the NC (Normally Closed) contact.

NOTE

Control of the failsafe relay output is configurable through ROS . One common application for this relay is to signal an alarm if a power failure occurs. For more information, refer to the ROS User Guide for the RSG2300.

The following shows the proper relay connections.

14 Connecting the Failsafe Alarm Relay

RUGGEDCOM RSG2300

Installation Guide

Chapter 2

Installing Device

1 3

2

Figure 12: Failsafe Alarm Relay Wiring

1. Normally Open 2. Common 3. Normally Closed

Section 2.4

Grounding the Device

The RSG2300 chassis ground terminal uses a #6-32 screw. It is recommended to terminate the ground connection with a #6 ring lug and torque it to 1.7 N·m (15 lbf·in).

2

3

1

Figure 13: Chassis Ground Connection

1. Stainless Steel Stud 2. #6-32 Screw 3. #6 Ring Lug

Section 2.5

Connecting to the Device

The following describes the various methods for accessing the ROS console and Web interfaces on the device.

For more detailed instructions, refer to the ROS User Guide for the RSG2300.

Grounding the Device 15

Chapter 2

Installing Device

RUGGEDCOM RSG2300

Installation Guide

RS232 Console Port

Connect a PC or terminal directly to the RS232 console port to access the boot-time control and ROS interfaces.

The console port provides access to ROS's console and Web interfaces.

IMPORTANT!

The console port is intended to be used only as a temporary connection during initial configuration or troubleshooting.

Connection to the console port is made using an RJ45-to-DB9 console cable. The following is the pin-out for the console port:

8 1

Figure 14: RJ45 Console Port Pin Configuration

RJ45

Male

1

2

Pin

DB9

Female

6

1

Name

DSR

DCD a a

Description

Data Set Ready

Carrier Detect

Comment

Reserved (Do

Not Connect)

3

4

5

6

7

8

1

4

5

2

3

8

7

9

DTR a

GND

RxD

TxD

CTS b

RTS b

RI c

Data Terminal

Ready

Signal Ground

Receive Data

(to DTE)

Transmit Data

(from DTE)

Clear to Send

Read to Send

Ring Indicator a

The DSR, DCD and DTR pins are connected together internally.

b

The CTS and RTS pins are connected together internally.

c

RI is not connected.

Communication Ports

Connect any of the available Ethernet ports on the device to a management switch and access the ROS console and Web interfaces via the device's IP address. For more information about available ports, refer to

Chapter 3,

Communication Ports

.

Section 2.6

Cabling Recommendations

Before connecting the device, be aware of the recommendations and considerations outlined in the following sections:

Section 2.6.1, “Protection On Twisted-Pair Data Ports”

Section 2.6.2, “Gigabit Ethernet 1000Base-TX Cabling Recommendations”

16 Cabling Recommendations

RUGGEDCOM RSG2300

Installation Guide

Chapter 2

Installing Device

Section 2.6.1

Protection On Twisted-Pair Data Ports

Siemens does not recommend the use of copper cabling of any length for critical, real-time substation automation applications. All copper Ethernet ports on RUGGEDCOM products include transient suppression circuitry to protect against damage from electrical transients and conform with IEC 61850-3 and IEEE 1613 Class 1 standards. This means that during a transient electrical event, communications errors or interruptions may occur, but recovery is automatic.

Siemens also does not recommend using copper Ethernet ports to interface with devices in the field across distances that could produce high levels of ground potential rise (i.e. greater than 2500 V), during line-to-ground fault conditions.

Section 2.6.2

Gigabit Ethernet 1000Base-TX Cabling Recommendations

The IEEE 802.3ab Gigabit Ethernet standard defines 1000 Mbit/s Ethernet communications over distances of up to 100 m (328 ft) using all 4 pairs in category 5 (or higher) balanced, unshielded twisted-pair cabling. For wiring guidelines, system designers and integrators should refer to the Telecommunications Industry Association (TIA)

TIA/EIA-568-A wiring standard that characterizes minimum cabling performance specifications required for proper

Gigabit Ethernet operation. For reliable, error-free data communication, new and pre-existing communication paths should be verified for TIA/EIA-568-A compliance.

The following table summarizes the relevant cabling standards:

Cabling Category

< 5

5

5e

6

> 6

1000Base-

TX Compliant

No

Yes

Yes

Yes

Yes

Required Action

New wiring infrastructure required.

Verify TIA/EIA-568-A compliance.

No action required. New installations should be designed with Category 5e or higher.

No action required.

Connector and wiring standards to be determined.

Follow these recommendations for copper data cabling in high electrical noise environments:

• Data cable lengths should be as short as possible, preferably 3 m (10 ft) in length. Copper data cables should not be used for inter-building communications.

• Power and data cables should not be run in parallel for long distances, and should be installed in separate conduits. Power and data cables should intersect at 90° angles when necessary to reduce inductive coupling.

• Shielded/screened cabling can be used when required. Care should be taken to avoid the creation of ground loops with shielded cabling.

Protection On Twisted-Pair Data Ports 17

RUGGEDCOM RSG2300

Installation Guide

Chapter 2

Installing Device

Gigabit Ethernet 1000Base-TX Cabling

Recommendations 18

RUGGEDCOM RSG2300

Installation Guide

Communication Ports

The RSG2300 can be equipped with various types of communication ports to enhance its abilities and performance.

1 3 5 6 7

Chapter 3

Communication Ports

2

Figure 15: Port Assignment

4

Each type of module has a specific location in the RSG2300 chassis:

• Slots 1 and 2 support any combination of two-port fiber or copper Ethernet modules up to 100 Mbps

• Slots 3 and 4 support any combination of fixed two-port 1 Gbps ports

• Slots 5, 6 and 7 house any combination of 8-port 10/100TX copper modules, up to a maximum of 24 ports

The exact configuration of the device can be determined by reading the factory data file through the ROS user interface. For more information about how to read the factory data file, refer to the ROS User Guide for the

RSG2300.

Each communication port is equipped with an LED that indicates the link/activity state of the port.

LED State

Green (Solid)

Green (Blinking)

Off

Description

Link established

Link activity

No link detected

1

Figure 16: Port LEDs

1. Port LED

The following sections describe the available communication ports:

Section 3.1, “Copper Ethernet Ports”

Section 3.2, “Fiber Optic Ethernet Ports”

Section 3.3, “SFP Optic Ethernet Ports”

Section 3.4, “GBIC Optic Ethernet Ports”

19

Chapter 3

Communication Ports

RUGGEDCOM RSG2300

Installation Guide

Section 3.1

Copper Ethernet Ports

The RSG2300 supports several 10/100/1000Base-TX Ethernet ports that allow connection to standard Category

5 (CAT-5) unshielded twisted-pair (UTP) cables with either RJ45 male connectors. The RJ45 connectors are directly connected to the chassis ground on the device and can accept CAT-5 shielded twisted-pair (STP) cables.

WARNING!

Electric shock hazard – risk of serious personal injury and/or equipment interference. If shielded cables are used, make sure the shielded cables do not form a ground loop via the shield wire and the

RJ45 receptacles at either end. Ground loops can cause excessive noise and interference, but more importantly, create a potential shock hazard that can result in serious injury.

Figure 17: 1 x 10/100/1000Tx with RJ45 Ports (1CG01)

Figure 18: 2 x 10/100/1000Tx with RJ45 Ports (CG01)

20

Figure 19: 2 x 10/100Tx with RJ45 Ports (TX01)

Figure 20: 2x 1000Tx SFP with RJ45 Ports (CG55)

Each port features an LED that indicates the state of the port.

State

Yellow (Solid)

Yellow (Blinking)

Off

Description

Link established

Link activity

No link detected

The following are the pin-out descriptions for the RJ45 connectors:

8 1

Figure 21: RJ45 Ethernet Port Pin Configuration

Pin

1

2

3

4

5

Name

10/100Base-TX 1000Base-TX

RX+ BI_DB+

RX-

TX+

Description

BI_DB-

Receive Data+ or Bi-Directional

Receive Dataor Bi-Directional

BI_DA+ Transmit Data+ or Bi-Directional

Reserved (Do Not Connect)

Reserved (Do Not Connect)

Copper Ethernet Ports

RUGGEDCOM RSG2300

Installation Guide

Chapter 3

Communication Ports

Pin

6

7

8

Name

1000Base-TX

BI_DA-

Description

10/100Base-TX

TXTransmit Dataor Bi-Directional

Reserved (Do Not Connect)

Reserved (Do Not Connect)

For specifications on the available copper Ethernet ports, refer to Section 4.4, “Copper Ethernet Port

Specifications”

.

Section 3.2

Fiber Optic Ethernet Ports

Fiber optic Ethernet ports are available with either MTRJ (Mechanical Transfer Registered Jack), LC (Lucent

Connector), SC (Standard or Subscriber Connector) or ST (Straight Tip) connectors. Make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly connected and matched to establish a proper link.

1

Figure 22: MTRJ Port

1. Tx Connector 2. Rx Connector

2

1

Figure 23: LC Port

1. Tx Connector 2. Rx Connector

2

1 2

1 2

Figure 24: SC Port

1. Tx Connector 2. Rx Connector

Figure 25: ST Port

1. Tx Connector 2. Rx Connector

For specifications on the available fiber optic Ethernet ports, refer to Section 4.5, “Fiber Optic Ethernet Port

Specifications”

.

Section 3.3

SFP Optic Ethernet Ports

SFP (Small Form-Factor Pluggable) optic Ethernet ports are available with LC (Lucent Connector) connectors.

Make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly connected and matched to establish a proper link.

Fiber Optic Ethernet Ports 21

Chapter 3

Communication Ports

RUGGEDCOM RSG2300

Installation Guide

1 2

Figure 26: LC Port

1. Tx Connector 2. Rx Connector

NOTE

SFP modules, as well as their optical ports, can be safely inserted and removed while the chassis is powered and operating.

The following sections describe how to install and remove SFP optical ports:

Section 3.3.1, “Installing an SFP Optical Port”

Section 3.3.2, “Removing an SFP Optical Port”

Section 3.3.1

Installing an SFP Optical Port

To install an SFP optical port, do the following:

CAUTION!

Electrical hazard – risk of damage to equipment. Use only components certified by Siemens with

RUGGEDCOM products. Damage to the module and device may occur if compatibility and reliability have not been properly assessed.

CAUTION!

Electrical hazard – risk of damage to equipment. Make sure all electrostatic energy is dissipated before installing or removing components from the device. An electrostatic discharge (ESD) can cause serious damage to the component once it is outside the chassis.

1. Make sure all potential electrostatic build-up has been properly discharged to prevent electrostatic discharges (ESD). This can be accomplished by wearing an ESD wrist strap or by touching Earth or the chassis ground.

2. Remove the dust cover from the port opening in the module.

CAUTION!

Mechanical hazard – risk of component damage. SFP optical ports are designed to insert in only one orientation. Do not force the port into the module.

3. Remove the port from its packaging.

4. Insert the port into the module and swing the bail-latch up to lock it in place.

22 Installing an SFP Optical Port

RUGGEDCOM RSG2300

Installation Guide

Chapter 3

Communication Ports

1

2

Figure 27: Installing an SFP Optical Port (Typical)

1. SFP Optical Port 2. Metal Bail-Latch

5. Remove the dust cover from the port.

6. Connect a cable to the port and test the connection.

Section 3.3.2

Removing an SFP Optical Port

To remove an SFP optical port, do the following:

CAUTION!

Electrical hazard – risk of damage to equipment. Make sure all electrostatic energy is dissipated before performing installing or removing components from the device. An electrostatic discharge (ESD) can cause serious damage to the component once it is outside the chassis.

1. Make sure all potential electrostatic build-up has been properly discharged to prevent electrostatic discharges (ESD). This can be accomplished by wearing an ESD wrist strap or by touching Earth or the chassis ground.

2. Disconnect the cable from the port.

3. Swing the metal bail-latch down and pull the port from the module.

1

2

Figure 28: Removing an SFP Optical Port (Typical)

1. SFP Optical Port 2. Metal Bail-Latch

4. Store the port in an ESD-safe bag or other suitable ESD-safe environment, free from moisture and stored at the proper temperature (-40 to 85 °C or -40 to 185 °F).

5. Insert a plug in the empty port opening to prevent the ingress of dust and dirt.

Removing an SFP Optical Port 23

Chapter 3

Communication Ports

RUGGEDCOM RSG2300

Installation Guide

Section 3.4

GBIC Optic Ethernet Ports

GBIC (Gigabit Interface Converter) optic Ethernet ports are available with SC (Standard or Subscriber Connector) connectors.

1 2

Figure 29: SC Port

1. Tx Connector 2. Rx Connector

The following sections describe how to install and remove GBIC optical ports:

Section 3.4.1, “Installing a GBIC Optical Port”

Section 3.4.2, “Removing a GBIC Optical Port”

Section 3.4.1

Installing a GBIC Optical Port

To install a GBIC optical port, do the following:

CAUTION!

Electrical hazard – risk of damage to equipment. Use only components certified by Siemens with

RUGGEDCOM products. Damage to the module and device may occur if compatibility and reliability have not been properly assessed.

CAUTION!

Electrical hazard – risk of damage to equipment. Make sure all electrostatic energy is dissipated before installing or removing components from the device. An electrostatic discharge (ESD) can cause serious damage to the component once it is outside the chassis.

1. Make sure all potential electrostatic build-up has been properly discharged to prevent electrostatic discharges (ESD). This can be accomplished by wearing an ESD wrist strap or by touching Earth or the chassis ground.

2. Remove the dust cover from the port opening in the module.

CAUTION!

Mechanical hazard – risk of component damage. GBIC optical ports are designed to insert in only one orientation. Do not force the port into the module.

3. Remove the port from its packaging.

4. Squeeze the latches on either side of the port and insert the port into the module.

24 GBIC Optic Ethernet Ports

RUGGEDCOM RSG2300

Installation Guide

Chapter 3

Communication Ports

1

2

3

Figure 30: Installing a GBIC Optical Port

1. GBIC Optical Port Module 2. GBIC Optical Port 3. Locking Latch

5. Release the latches and make sure the module is locked in place.

6. Remove the dust cover from the port.

7. Connect a cable to the port and test the connection.

Section 3.4.2

Removing a GBIC Optical Port

To remove an GBIC optical port, do the following:

CAUTION!

Electrical hazard – risk of damage to equipment. Make sure all electrostatic energy is dissipated before performing installing or removing components from the device. An electrostatic discharge (ESD) can cause serious damage to the component once it is outside the chassis.

1. Make sure all potential electrostatic build-up has been properly discharged to prevent electrostatic discharges (ESD). This can be accomplished by wearing an ESD wrist strap or by touching Earth or the chassis ground.

2. Disconnect the cable from the port.

3. Squeeze the latches on either side of the port and pull it from the module.

Removing a GBIC Optical Port 25

Chapter 3

Communication Ports

RUGGEDCOM RSG2300

Installation Guide

1

2

3

Figure 31: Removing a GBIC Optical Port

1. GBIC Optical Port Module 2. GBIC Optical Port 3. Locking Latch

4. Store the port in an ESD-safe bag or other suitable ESD-safe environment, free from moisture and stored at the proper temperature (-40 to 85 °C or -40 to 185 °F).

5. Insert a plug in the empty port opening to prevent the ingress of dust and dirt.

26 Removing a GBIC Optical Port

RUGGEDCOM RSG2300

Installation Guide

Chapter 4

Technical Specifications

Technical Specifications

The following sections provide important technical specifications related to the device and available modules:

Section 4.1, “Power Supply Specifications”

Section 4.2, “Failsafe Relay Specifications”

Section 4.3, “Supported Networking Standards”

Section 4.4, “Copper Ethernet Port Specifications”

Section 4.5, “Fiber Optic Ethernet Port Specifications”

Section 4.6, “Operating Environment”

Section 4.7, “Mechanical Specifications”

Section 4.1

Power Supply Specifications

Power Supply Type

Input Range

Maximum

36 VDC

Internal Fuse Rating

ab

24 VDC

Minimum

10 VDC 6.3 A(F)

48 VDC

HI (125/250 VDC) d

36 VDC

88 VDC

59 VDC

300 VDC

3.15 A(T)

2 A(T)

HI (110/230 VAC) d

85 VAC 264 VAC 2 A(T) a

(F) denotes fast-acting fuse

b

(T) denotes time-delay fuse.

c

Power consumption varies based on configuration. 10/100Base-TX ports consume roughly 1 W less than fiber optic ports.

d

The HI power supply is the same power supply for both AC and DC.

Maximum Power

Consumption

c

25 W

Section 4.2

Failsafe Relay Specifications

Parameter

Max Switching Voltage

Rated Switching Current

Maximum Switching Capacity

Value (Resistive Load)

240 VAC, 125 VDC

2 A @ 240 VAC, 0.15 A @ 125 VDC, 2 A @ 30 VDC

150 W, 500 VA

Power Supply Specifications 27

Chapter 4

Technical Specifications

RUGGEDCOM RSG2300

Installation Guide

Section 4.3

Supported Networking Standards

10 Mbps Ports 100 Mbps Ports

1000 Mbps

Ports

Standard

IEEE 802.3

IEEE 802.3u

IEEE 802.3x

IEEE 802.3z

IEEE 802.3ab

IEEE 802.3ad

IEEE 802.1D

IEEE 802.1D

IEEE 802.1p

IEEE 802.1Q

IEEE 802.1w

IEEE 802.1x

IEEE

802.1Q-2005

(formerly 802.1s)

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

ü

Notes

10BaseT/10BaseFL

100BaseTX/100BaseFX

Flow Control

1000BaseLX

1000BaseTx

Link Aggregation

MAC Bridges

Spanning Tree Protocol (STP)

Class of Service (CoS)

VLAN (Virtual LAN) Tagging

Rapid Spanning Tree Protocol (RSTP)

Port-Based Network Access Control

Multiple Spanning Tree Protocol (MSTP)

Section 4.4

Copper Ethernet Port Specifications

The following details the specifications for copper Ethernet ports that can be ordered with the RSG2300.

Section 4.4.1

Copper Fast (10/100 Mbps) Ethernet Port Specifications

Connector Duplex

e

Cable Type

f

RJ45 FDX/HDX > CAT-5 e

Auto-Negotiating

f

Shielded or unshielded.

g

Auto-crossover and auto-polarity.

h

Typical distance. Dependent on the number of connectors and splices.

i

RMS 1 minute.

Wiring Standard

g

TIA/EIA T568A/B

Maximum

Distance

h

100 m (328 ft)

Isolation

i

1.5 kV

28 Supported Networking Standards

RUGGEDCOM RSG2300

Installation Guide

Chapter 4

Technical Specifications

Section 4.4.2

Copper Gigabit Ethernet (1 Gbps) Port Specifications

NOTE

• Maximum segment length is greatly dependent on factors such as fiber quality, and the number of patches and splices. Consult a Siemens sales associate when determining maximum segment distances.

• All optical power numbers are listed as dBm averages.

• F51 transceivers are rated for -40 to 85 °C (-40 to 185 °F).

Fixed Gigabit Transceivers

Connector Duplex

j

Cable Type

k

RJ45 FDX/HDX > CAT-5 j

Auto-Negotiating

k

Shielded or unshielded.

l

Auto-crossover and auto-polarity.

m

Typical distance. Dependent on the number of connectors and splices.

n

RMS 1 minute.

SFP Gigabit Transceivers

Connector Duplex

o

RJ45 o

Auto-Negotiating

p

Shielded or unshielded.

q

Auto-crossover and auto-polarity.

r

RMS 1 minute.

FDX/HDX

Cable Type

p

> CAT-5

Wiring Standard

l

TIA/EIA T568A/B

Maximum

Distance

m

100 m (328 ft)

Wiring Standard

q

TIA/EIA T568A/B

Maximum Distance

100 m (328 ft)

Isolation

n

1.5 kV

Isolation

r

1.5 kV

Section 4.5

Fiber Optic Ethernet Port Specifications

The following sections list specifications of the optical transceivers used in the dual-port modules available for the

RSG2300:

Section 4.5.1, “10FL Ethernet Optical Specifications”

Section 4.5.2, “Fast Ethernet (10/100 Mbps) Optical Specifications”

Section 4.5.3, “Gigabit Ethernet (1 Gbps) Optical Specifications”

Copper Gigabit Ethernet (1 Gbps) Port Specifications 29

Chapter 4

Technical Specifications

RUGGEDCOM RSG2300

Installation Guide

Section 4.5.1

10FL Ethernet Optical Specifications

Mode

MM s

Typical.

Connector

Type

Cable

Type (µm)

ST

62.5/125

50/125

Tx λ (nm)

s

850

Tx min

(dBm)

-16

-19.8

Tx max

(dBm)

-9

-12.8

Rx

Sensitivity

(dBm)

Rx

Saturation

(dBm)

Distance

(typ.) (km)

-34 -11.2

2

Power

Budget

(dB)

18

14.2

Section 4.5.2

Fast Ethernet (10/100 Mbps) Optical Specifications

Mode

Connector

Type

Cable

Type (µm)

Tx λ (nm)

t

Tx min.

(dBm)

Tx max.

(dBm)

MM

MM

MM

ST

SC

MTRJ

62.5/125

50/125

62.5/125

50/125

62.5/125

50/125

1300

1300

1300

-19

-22.5

-19

-22.5

-19

-22.5

-14

-14

-14

SM

SM

SM

SM

SM

SM

SM

ST

SC

LC

SC

LC

SC

LC

9/125

9/125

9/125

9/125

9/125

9/125

9/125

1310

1310

1310

1310

1310

1310

1310

-15

-15

-15

-5

-5

0

0

MM LC 62.5/125 1300 -19 -14 t

Typical.

u

Typical distance. Dependent on the cable type, number of connectors and number of splices.

0

5

5

-8

0

-8

-8

Rx

Sensitivity

(dBm)

Rx

Saturation

(dBm)

Maximum

Distance

(km)

u

-31

-31

-31

-35

-37

-37

-32

-31

-34

-34

-32

-14

-14

-14

3

0

0

-7

-3

-3

-7

-14

2

2

2

50

90

90

20

20

20

50

2

30

37

37

17

16

19

29

12

8.5

12

8.5

Power

Budget

(dB)

12

8.5

13

30 10FL Ethernet Optical Specifications

RUGGEDCOM RSG2300

Installation Guide

Chapter 4

Technical Specifications

Section 4.5.3

Gigabit Ethernet (1 Gbps) Optical Specifications

Fixed Gigabit Transceivers

NOTE

These transceivers utilize a distributed feedback (DFB) type laser and are rated for -20 to 85 °C (-4 to

185 °F) operation only.

Mode

Connector

Type

Cable

Type (µm)

v

Tx λ (nm)

w

Tx

Minimum

(dBm)

x

Tx

Maximum

(dBm)

x

Rx

Sensitivity

(dBm)

x

Rx

Saturation

(dBm)

x

Maximum

Distance

(km)

y

Power

Budget

(dB)

MM

SM

SM

LC

SC

LC

50/125

62.5/125

9/125

9/125

850

1310

1310

-9

-10

-9.5

-2.5

-3

-3

-20

-20

-21

0

-3

-3

0.5

10

10

11

10

11.5

SM SC 9/125 1310 -5 0 -20 -3 25 15

SM LC 9/125 1310 -7 -3 -24 -3 25 17 v

All cabling is duplex type unless specified otherwise.

w

Typical.

x

All optical power numbers are listed as dBm averages.

y

Typical distance. The maximum segment length is greatly dependent on factors such as fiber quality, and the number of patches and splices. Consult a Siemens sales associates when determining maximum segment distances.

SFP Gigabit Transceivers

NOTE

SFP transceivers have a temperature range of -40 to 85 °C (-40 to 185 °F), unless specified otherwise.

Mode

Connector

Type

Cable

Type (µm)

Tx λ (nm)

z

Tx

Minimum

(dBm)

Tx

Maximum

(dBm)

Rx

Sensitivity

(dBm)

Rx

Saturation

(dBm)

Maximum

Distance

(km)

ab

0.5

Power

Budget

(dB)

MM ac

LC

50/125

850 -9 -2.5

-20 0

0.3

10

11

SM LC

62.5/125

9/125 1310 -9.5

-3 -19 -3 9.5

SM

SM ad

LC

LC

9/125

9/125

1310

1550

-7

0

-3

5

-23

-23

-3

-3

25

70

16

23 z

Typical.

aa

All optical power numbers are listed as dBm averages.

ab

Typical distance. The maximum segment length is greatly dependent on factors such as fiber quality, and the number of patches and splices. Consult a Siemens sales associates when determining maximum segment distances.

ac

Operating temperature range of -10 to 85 °C (14 to 185 °F).

ad

Operating temperature range of 0 to 70 °C (32 to 185 °F).

Gigabit Ethernet (1 Gbps) Optical Specifications 31

Chapter 4

Technical Specifications

RUGGEDCOM RSG2300

Installation Guide

GBIC Gigabit Transceivers

NOTE

GBIC transceivers have a temperature range of -40 to 85 °C (-40 to 185 °F), unless specified otherwise.

Mode

Connector

Type

Cable

Type (µm)

Tx λ

(nm)

ae

Tx

Minimum

(dBm)

af

-9.5

Tx

Maximum

(dBm)

af

-3

Rx

Sensitivity

(dBm)

af

-21

Rx

Saturation

(dBm)

af

-3

Maximum

Distance

(km)

ag

10

Power

Budget

(dB)

11.5

SM SC 9/125 1310

SM

SM ah

SC

SC

9/125

9/125

1310

1550

-7

0

-3

5

-24

-23

-3

-3

25

70

17

23 ae

Typical.

af

All optical power numbers are listed as dBm averages.

ag

Typical distance. The maximum segment length is greatly dependent on factors such as fiber quality, and the number of patches and splices. Consult a Siemens sales associates when determining maximum segment distances.

ah

Operating temperature range of -25 to 85 °C (-13 to 185 °F).

Section 4.6

Operating Environment

Parameter

Ambient Operating Temperature

Range

-40 to 85 °C (-40 to 185 °F)

Ambient Relative Humidity

Ambient Storage Temperature

5% to 95%

-40 to 85 °C (-40 to 185 °F)

Comments

Ambient Temperature as measured from a 30 cm radius surrounding the center of the enclosure.

Non-condensing

Section 4.7

Mechanical Specifications

Parameter

Dimensions

Weight

Ingress Protection

Enclosure

Value

Refer to Chapter 5, Dimension Drawings

5.2 kg (11.5 lbs)

IP40 (1 mm or 0.04 in objects)

18 AWG Galvanized Steel

32 Operating Environment

RUGGEDCOM RSG2300

Installation Guide

Dimension Drawings

NOTE

All dimensions are in millimeters, unless otherwise stated.

NOTE

Dimensional tolerances are in accordance with ISO 2768-mK, unless otherwise stated.

Chapter 5

Dimension Drawings

438.15

Figure 32: Overall Dimensions

33

Chapter 5

Dimension Drawings

32.64

21.08

11.68

479.29

RUGGEDCOM RSG2300

Installation Guide

Figure 33: Rack Mount Dimensions

4.57

461.01

34

RUGGEDCOM RSG2300

Installation Guide

10.4

7.4

1

2

E

N-8

R M

WER

WER

S OL

0 0-

P O

ALA

P O

C ON

5 76

D E MO

X P LE

T US

E D

D U

S TA

S PE

2 4

2 0

1 6

1 2

3 2

2 8

8

4

2 3

1 9

1 5

1 1

3 1

2 7

7

3

2 2

1 8

1 4

1 0

3 0

2 6

6

2

2 9

2 5

2 1

1 7

1 3

9

5

1

486.4

476.3

P 32

P 31

P 30

P 29

P 28

P 27

P 26

P 25

P 24

P 23

P 22

P 21

P 20

P 19

P 18

P 17

P 16

P 15

P 14

P 13

P 12

P 11

P 10

P 9

P 8 P 7 P 6 P 5 P 4 P 3 P 2 P 1

Chapter 5

Dimension Drawings

11.7

Figure 34: Panel and DIN Rail Mount Dimensions

35

RUGGEDCOM RSG2300

Installation Guide

Chapter 5

Dimension Drawings

36

RUGGEDCOM RSG2300

Installation Guide

Chapter 6

Certification

Certification

The RSG2300 device has been thoroughly tested to guarantee its conformance with recognized standards and has received approval from recognized regulatory agencies.

Section 6.1, “Agency Approvals”

Section 6.2, “FCC Compliance”

Section 6.3, “Industry Canada Compliance”

Section 6.4, “EMI and Environmental Type Tests”

Section 6.1

Agency Approvals

Agency

CSA

CE

FCC

FDA/CDRH

ISO

Standards

CSA C22.2 No. 60950-1, UL 60950-1

EN 60950-1, EN 61000-6-2, EN

60825-1, EN 55022 Class A, EN 50581

FCC Part 15, Class A

21 CFR Chapter I, Sub-chapter J

ISO9001:2008

Comments

Approved

CE Compliance is claimed via

Declaration of Self Conformity Route

Approved

Approved

Designed and manufactured using an

ISO9001:2008 certified quality program

Section 6.2

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference on his own expense.

Section 6.3

Industry Canada Compliance

CAN ICES-3 (A) / NMB-3 (A)

Agency Approvals 37

Chapter 6

Certification

Section 6.4

EMI and Environmental Type Tests

The RSG2300 has passed the following EMI and environmental tests.

IEC 61850-3 EMI Type Tests

Test

IEC 61000-4-2

IEC 61000-4-3

ESD

Radiated RFI

Description

Enclosure Contact

Enclosure Air

Enclosure Ports

IEC 61000-4-4 Burst (Fast Transient)

IEC 61000-4-5 Surge

Signal Ports

DC Power Ports

AC Power Ports

Earth Ground Ports a

Signal Ports

IEC 61000-4-6 Induced (Conducted) RFI

DC Power Ports

AC Power Ports

Test Levels

+/- 8 kV

+/- 15 kV

20 V/m

+/- 4 kV @ 2.5 kHz

+/- 4 kV

+/- 4 kV Line-to-Earth,

+/- 2 kV Line-to-Line

+/- 2 kV Line-to-Earth,

+/- 1 kV Line-to-Line

+/- 4 kV Line-to-Earth,

+/- 2 kV Line-to-Line

10 V

IEC 61000-4-8 Magnetic Field

Signal Ports

DC Power Ports

AC Power Ports

Earth Ground Ports a

Enclosure Ports

IEC 61000-4-29

IEC 61000-4-11

IEC 61000-4-12

Voltage Dips and

Interrupts (DC

Power Ports)

Voltage Dips and

Interrupts (A. C.

Power Ports)

Damped Oscillatory

DC Power Ports

AC Power Ports

AC Power Ports

40 A/m, Continuous,

1000 A/m for 1 s

30% for 0.1 s

60% for 0.1 s

100% for 0.05 s

30% for 1 period

60% for 50 periods

100% for 5 periods

100% for 50 periods

2.5 kV Common,

1 kV Differential

Mode @1 MHz

IEC 61000-4-16

IEC 61000-4-17

Mains Frequency Voltage

Ripple on DC

Power Supply

Signal Ports

DC Power Ports

AC Power Ports

Signal Ports

DC Power Ports

DC Power Ports

30 V Continuous,

300 V for 1s

10%

38

RUGGEDCOM RSG2300

Installation Guide

Severity Levels

4

4

4

3

4

3

4

3

3

EMI and Environmental Type Tests

RUGGEDCOM RSG2300

Installation Guide

Chapter 6

Certification

Test

IEC 60255-5

Description

Dialiectric Strength Signal Ports

H.V. Impulse

DC Power Ports

AC Power Ports

Signal Ports

Test Levels

2 kVAC (Fail-

Safe Relay Output)

1.5 kVDC

2 kVAC

5 kV (Fail-Safe

Relay Output)

5 kV

Severity Levels

IEC 1613/C37.90

IEC 1613/C37.90.1

Dialiectric Strength

H.V. Impulse

Oscillatory

DC Power Ports

AC Power Ports

Signal Ports

DC Power Ports

AC Power Ports

Signal Ports

DC Power Ports

AC Power Ports

Signal Ports

DC Power Ports

AC Power Ports

Fast Transient Signal Ports

DC Power Ports

IEEE C37.90.2

IEC 1613/C37.90.3

Radiated RFI

ESD

AC Power Ports

Earth Ground Ports a

Enclosure Ports

Enclosure Contact

Enclosure Air a

Only applicable to functional earth connections separated from the safety earth connection.

5 kV (Fail-Safe

Relay Output)

5 kV

5 kV

2 kVAC

1.5 kVDC

2 kVAC

2.5 kV Common

Mode @1 MHz

2.5 kV Common,

1 kV Differential

Mode @1 MHz

+/- 4 kV @ 2.5 kHz

+/- 4 kV

35 V/m

+/- 8 kV

+/- 15 kV

IEEE 1613 (C37.90.x) EMI Immunity Type Tests

NOTE

The RSG2300 meets Class 2 requirements for an all-fiber configuration and Class 1 requirements for copper ports.

Test

IEEE C37.90.3

IEEE C37.90.2

IEEE C37.90.1

ESD

Radiated RFI

Fast Transient

Description

Enclosure Contact

Enclosure Air

Enclosure Ports

Signal Ports

Test Levels

+/-8 kV

+/-15 kV

35 V/m

+/- 4 kV @ 2.5 kHz

EMI and Environmental Type Tests 39

Chapter 6

Certification

Test

Oscillatory

Description

DC Power Ports

AC Power Ports

Earth Ground Ports

Signal Ports

DC Power Ports

IEEE C37.90

IEEE C37.90

H.V. Impulse

Dielectric Strength

Environmental Type Tests

Test

IEC 60068-2-1

Description

Cold Temperature

IEC 60068-2-2

IEC 60068-2-30

Dry Heat

Humidity (Damp Heat, Cyclic)

AC Power Ports

Signal Ports

DC Power Ports

AC Power Ports

Signal Ports

DC Power Ports

AC Power Ports

Test Ad

Test Bd

Test Db

IEC 60068-21-1

IEC 60068-21-2

Vibration

Shock

RUGGEDCOM RSG2300

Installation Guide

Test Levels

+/- 4 kV

+/- 4 kV

+/- 4 kV

2.5 kV Common Mode @1MHz

2.5 kV common, 1 kV differential mode @ 1 MHz

2.5 kV common, 1 kV differential mode @ 1 MHz

5 kV (Fail-Safe Relay Output)

5 kV

5 kV

2 kVAC

1.5 kVDC

2 kVAC

Test Levels

-40 °C (-40 °F), 16 Hours

85 °C (185 °F), 16 Hours

95% (non-condensing),

55 °C (131 °F), 6 cycles

2g @ 10-50 Hz

30 g @ 11 ms

40 EMI and Environmental Type Tests

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents