Huskystar E10 Owner Manual

USER’S GUIDE
E10
Always unplug before relamping. Replace bulb with same type rated
10W (110V-120V), 15W (220-240V).
•
Do not allow to be used as a toy. Close attention is necessary when
this sewing machine is used by or near children and in¿rm persons.
Use this sewing machine only for its intended use as described in this
manual. Use only attachments recommended by the manufacturer as
contained in this manual.
Never operate this sewing machine if it has a damaged cord or
plug, if it is not working properly, if it has been dropped or damaged,
or dropped into water. Return the sewing machine to the nearest
authorized dealer or service center for examination, repair, electrical or
mechanical adjustment.
•
•
•
electric shock, or injury to persons:
WARNING - To reduce the risk of burns, ¿re,
A sewing machine should never be left unattended when plugged in.
Always unplug this sewing machine from the electric outlet immediately
after using and before cleaning.
•
shock:
DANGER - To reduce the risk of electric
When using an electrical appliance, basic safety precautions should always
be followed, including the following:
Read all instructions before using this household sewing machine.
IMPORTANT SAFETY
INSTRUCTIONS
This houshold sewing machine is designed to comply with IEC/EN 60335-2-28 and
UL1594
Keep ¿ngers away from all moving parts. Special care is required
around the sewing machine needle.
Always use the proper needle plate. The wrong plate can cause the
needle to break.
Do not use bent needles.
Do not pull or push fabric while stitching. It may deÀect the needle
causing it to break.
Switch the sewing machine off (“0”) when making any adjustment in
the needle area, such as threading needle, changing needle, threading
bobbin, or changing presser foot, etc.
Always unplug sewing machine from the electrical outlet when
removing covers, lubricating, or when making any other user servicing
adjustments mentioned in the instruction manual.
Never drop or insert any object into any opening.
Do not use outdoors.
Do not operate where aerosol (spray) products are being used or
where oxygen is being administrated.
To disconnect, turn all controls to the off (“0”) position, then remove
plug from outlet.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the
cord.
•
•
•
•
SAVE THESE INSTRUCTIONS
•
•
•
•
•
•
•
Never operate the sewing machine with any air openings blocked.
Keep ventilation openings of the sewing machine and foot controller
free from the accumulation of lint, dust, and loose cloth.
•
To ensure that you are always provided with the most modern sewing capabilities, the manufacturer reserves the
right to change appearance, design or accessories of this sewing machine when considered necessary.
May we suggest that before you start to use your sewing machine, you discover the many features and
advantages by going through this instruction book, step by step, while seated at your sewing machine.
Your sewing machine offers the ultimate in simplicity and ease of operation. For your safety and to fully enjoy the
many advantages and ease of operation of your sewing machine, we recommend that you read all the important
safeguards and use and care instructions in this instruction book.
As the owner of a new sewing machine, you will enjoy precision quality stitching on all types of fabrics, from
multiple layers of denim to delicate silks.
Congratulations!
TROUBLE SHOOTING GUIDE ...............................................................................30
MAINTENANCE ......................................................................................................29
STITCH SELECTION ..............................................................................................28
3-STEP ZIG-ZAG ....................................................................................................27
ZIPPERS AND PIPING............................................................................................26
BLIND HEM .............................................................................................................25
HOW TO SEW BUTTONHOLES .............................................................................23
ZIGZAG STITCHING ...............................................................................................22
STRAIGHT STITCHING ..........................................................................................21
MATCHING NEEDLE / FABRIC / THREAD ............................................................20
REVERSE SEWING/REMOVING THE FABRIC/CUTTING THE THREAD ............19
BRINGING UP THE BOBBIN THREAD ..................................................................18
THREAD TENSION .................................................................................................17
THREADING THE UPPER THREAD ......................................................................16
INSERTING THE NEEDLE .....................................................................................15
INSERTING THE BOBBIN ......................................................................................14
WINDING THE BOBBIN ..........................................................................................13
ATTACHING THE PRESSER FOOT SHANK/ANKLE .............................................12
TWO-STEP PRESSER FOOT LEVER/ADJUST PRESSER FOOT PRESSURE ... 11
CHANGING THE BULB...........................................................................................10
Sewing light ...............................................................................................................9
Foot control................................................................................................................9
CONNECTING THE MACHINE TO POWER SOURCE ............................................9
FITTING THE SNAP-IN ACCESSORY BOX .............................................................8
ACCESSORIES.........................................................................................................7
PRINCIPAL PARTS OF THE MACHINE....................................................................5
LIST OF CONTENTS
4
1. Thread tension dial
2. Presser foot pressure
3. Thread take-up lever
4. Thread cutting
5. Presser foot
6. Needle plate
7. Accessories box
8. Bobbin stop
9. Stitch length dial
10. Stitch display
11. Reverse sewing lever
PRINCIPAL PARTS OF THE MACHINE
5
12. Spool pin
13. Bobbin winder
14. Hole for second spool pin
15. Hand wheel
16. Stitch selector dial
17. Power switch
18. Main plug socket
19. Bobbin thread guide
20. Upper thread guide
21. Handle
22. Presser foot lever
6
1. All purpose foot
2. Zipper foot
3. Satin stitch foot
4. Blind hem foot
5 Buttonhole foot
6. L-screwdriver
7. Seam ripper/ brush
8. Oil bottle
9. Second spool pin
10. Spool holders (2x)
11. Pack of needles
12. Seam guide
13. Bobbins (3x)
14. Darning plate
15. Felt pad
ACCESSORIES
7
9
13
12
2
8
5
1
6
10
14
3
7
15
11
4
To open, lift up at the point of the arrow. (2)
Keep the snap-in accessory box horizontal, and push it in the
direction of the arrow. (1)
FITTING THE SNAP-IN ACCESSORY BOX
8
For USA and Canada
For appliance with a polarized plug (one blade is wider than the
other).
To reduce the risk of electric shock, this plug is intended to ¿t in
a polarized outlet only one way. If it does not ¿t fully in the outlet,
reverse the plug. If it still does not ¿t, contact a quali¿ed electrician
to install the proper outlet. Do not modify the plug in any way.
Sewing light
Press main switch (A) for power and light on. (“ l “)
For Australia and Europe, 220-240V: KD-2902
For USA and Canada, 110-120V: KD-1902
Attention:
Consult a quali¿ed electrician if in doubt as to how to connect machine to
power source.
Unplug power cord when machine is not in use.
The appliance must be used with the foot controller:
Foot control
Foot control regulates the sewing speed. (3)
Attention:
Unplug power cord when machine is not in use.
Connect the machine to a power source as illustrated. (1)
A polarized plug must be used with the appropriate polarized outlet.
(2)
CONNECTING THE MACHINE TO POWER SOURCE
9
1
3
Remove the cover (B).
Unscrew the bulb and ¿t new one (C). (2)
Replace the cover and tighten screw.
-
-
-
Should there be any problem, ask your local dealer for advice.
Loosen screw (A) as illustrated. (1)
-
Replace bulb with same type rated 10 watts (110-120V) or 15 watts
(220-240V).
Attention:
Disconnect the machine from the power supply by removing the plug from
the main socket!
CHANGING THE BULB
10
For sewing very thin fabric, loosen the pressure by turning the screw
counter clockwise for less pressure on the fabric, and for heavy
fabric, tighten by turning it clockwise for more pressure on the fabric.
However, if you need to adjust the presser foot pressure, turn the
presser adjusting screw with a coin.
The presser foot pressure of the machine has been pre-set and
usually requires no readjustment for most fabrics (light-or-heavy
weight).
ADJUST PRESSER FOOT PRESSURE
When sewing several layers or thick fabrics, the presser foot can be
raised to extra high for easy positioning of the work. (A)
TWO-STEP PRESSER FOOT LEVER
11
-
Loosen
+
Tighten presser
adjusting screw
Attention:
Turn power switch to off (“O”) when carrying out any of the above
operations!
Attaching the seam guide
Attach the seam guide (g) in the slot on the shank/ankle as
illustrated.
Adjust according to need for hems, pleats, quilting, etc. (4)
Removing the presser foot
Raise the presser foot. (3)
Raise the lever (e) and the foot disengages.
Attaching the presser foot
Lower the presser foot shank/ankle (b) until the cut-out (c) is directly
above the pin on the foot (d). (2)
Raise the lever (e).
Lower the presser foot shank/ankle (b) and the presser foot (f) will
engage automatically.
Attaching the presser foot holder
Raise the presser foot bar (a). (1)
Attach the presser foot shank/ankle (b) as illustrated.
ATTACHING THE PRESSER FOOT SHANK/ ANKLE
12
Wind thread clockwise around bobbin winder tension discs (3).
Thread bobbin as illustrated and place on spindle (4).
Push bobbin to right (5).
Hold thread end (6).
Step on foot control pedal (7) to wind the bobbin.
Cut thread (8).
Press bobbin to left (9) and remove.
-
-
-
-
-
-
-
Please Note:
When the bobbin winder spindle is in “bobbin winding” position, the
machine will not sew and the hand wheel will not turn.
To start sewing, push the bobbin winder spindle to the left (sewing
position).
For smaller spools of thread place spool holder with small side
next to spool (2).
-
Place thread and spool holder onto spool pin (1).
WINDING THE BOBBIN
13
Attention:
Turn power switch to off (“O”).
5. Insert it into the shuttle.
4. Hold the bobbin case by the hinged latch.
3. Put the thread under the tension spring.
2. Hold the bobbin case with one hand. Insert the bobbin so that
the thread runs in a clockwise direction (arrow).
1. Open the hinged cover.
When inserting or removing the bobbin, the foot and needle must be
fully raised.
INSERTING THE BOBBIN
14
Problems can occur with:
A. Bent needles
B. Damaged points
C. Blunt needles
Needles must be in perfect condition. (2)
Attention:
Turn power switch to off (“O”).
Insert the needle following the illustrated instructions.
A. Loosen the needle clamp screw and tighten again after inserting
the new needle. (1)
B. The Àat side of the needle shaft should be towards the back.
C/D.Insert the needle as far up as it will go.
Change the needle regularly, especially if it is showing signs of wear
and causing problems.
INSERTING THE NEEDLE
15
Start by raising the needle to its highest point (1), and also raise
the presser foot to release the tension discs. (2)
-
-
-
-
-
-
Lift up the spool pin. Place the spool of thread on the holder
with the thread coming off the spool as shown. For small thread
spools, place small side of spool holder next to spool. (3)
Draw thread from spool through the upper thread guide. (4)
Guide thread around thread guide (5) pulling thread through pretension spring as illustrated.
Thread tension disks by leading thread down in right channel
and up in left channel (6). During this process it is helpful to hold
the thread between the spool and thread guide (4).
At the top pull thread from right to left through the slotted eye of
the take-up lever and then down again. (7)
Place thread behind the thin wire needle clamp guide (8) and
then down to the needle eye and thread from front to back.
Pull about 6-8 inches of thread under the presser foot to the
back. Trim thread to length with built in thread cutter. (9)
Attention:
For safety, it is strongly suggested you turn off the power before threading.
-
Threading is simple but it is important to thread correctly to prevent
sewing problems could result.
THREADING THE UPPER THREAD
16
Note:
The bobbin thread tension does not normally have to be adjusted.
A. Normal thread tension - upper and bobbin thread join in fabric
B. Upper thread tension too loose - upper thread “loops” on the
underside of fabric
C. Upper thread tension too tight - bobbin thread “loops”on the top
side of the fabric
Basic thread tension setting: “4”
To increase the tension, turn the dial to the next number up.
To reduce the tension, turn the dial to the next number down.
THREAD TENSION
17
Place both threads to the back under the presser foot. (2)
Pull on the upper thread to bring the bobbin thread up through the
stitch plate hole.
Hold the upper thread with the left hand. Turn the handwheel
towards you until the needle is raised. (1)
BRINGING UP THE BOBBIN THREAD
18
Hold the threads behind the presser foot with both hands, pull them
into the thread cutter (B) and down (3) to cut.
CUTTING THE THREAD
Turn the handwheel toward you to bring the thread take up lever to
its highest position, raise the presser foot and remove fabric to the
back. (2)
REMOVING THE FABRIC
At the end of a seam, press down the reverse sewing lever. Sew a
few reverse stitches to “the tie off” the thread ends.
Release the lever and the machine will sew forwards again. (1/A)
REVERSE SEWING
19
EXPLANATION
Standard sharp needles.
Sizes range thin to large. 9 (65) to 18(110)
Semi-ball point needle, scarfed. 9(65) to 18(110)
Full ball point needle 9(65) to 18(110)
Leather needles. 12(80) to 18(110)
NEEDLES
HA×1
15×1
15×1/705H(SIN)
15×1/705H (SUK)
130 PCL
NEEDLE, FABRIC SELECTION
20
Heavy duty thread, carpet thread.
(Increase presser foot pressure and top tension.)
Most threads sold are medium size and suitable for these fabrics and
needle sizes.
Use polyester threads on synthetic materials and cotton on natural
woven fabrics for best results.
Always use the same thread on top and bottom.
Light-duty thread in cotton, nylon or polyester.
THREAD
Leather, vinyl, upholstery.
(Leaves smaller hole than standard large needle.)
Sweater knits, Lycra, swimsuit fabric, elastic.
Natural and synthetic woven fabrics, polyester blends.Knits-polyesters,
interlocks, tricot, single and double knits.
Can be used instead of 15×1 for sewing all fabrics.
Natural woven fabrics-wool, cotton, silk, etc.
Qiana. Not recommended for double knits.
TYPE OF FABRIC
Heavy wool, overcoat fabrics, upholstery fabrics, some leathers and vinyls.
18(110)
IMPORTANT: Match needle size to thread size and weight of fabric
Medium weight fabrics-cotton duck, wool, heavier knits, terrycloth, denims.
Heavyweight fabrics-canvas, wool, outdoor tent and quilted fabrics,
denims, upholstery material (light to medium).
Medium weight fabrics-cotton, satin, kettlecloth, sailcloth, double knits,
lightweight wool.
12(80)
16(100)
Lightweight fabrics-thin cottons, voile, silk , muslin, interlocks, cotton knits,
tricots, jerseys, crepes, woven polyester, shirt & blouse fabrics.
9-11(65-75)
14(90)
FABRICS
NEEDLE SIZE
NEEDLE, FABRIC, THREAD SELECTION GUIDE
MATCHING NEEDLE / FABRIC / THREAD
S1 for stretch fabrics
Suggested stitch lengths:
2.0 for lightweight fabrics
2.5 for medium weight fabrics
3.0 for heavy weight fabrics
4.0-5.0 for basting
To get the reinforced triple straight stitch, turn the stitch length dial to
position “S1”.
Adjust the stitch length by turning the stitch length dial to the desired
stitch length.
Straight stitching right needle position
Turn the stitch selector dial so that the “B” appears in the stitch
display window.
To get the reinforced triple straight stitch, turn the stitch length dial to
position “S1”.
Straight stitching center needle position
Turn the stitch selector dial so that the “A” appears in the stitch
display window.
Snap on the standard presser foot.
Adjust the stitch length by turning the stitch length dial to the desired
stitch length. 2.5 is standard stitch length.
STRAIGHT STITCHING
21
Straight stitch
Reverse sewing lever
Stitch selection dial
Stitch display
Stitch length dial
Function of stitch length dial while zigzaging
The density of zigzag stitches increase as the setting of stitch length
dial approaches “0”.
Zigzag stitches are usually sewn at “2.5” or less.
Dense zigzag stitches (close together) are referred to as a satin
stitch.
Turn the stitch selector dial so that the stitch display shows “C”-zigzag. Turning the stitch selector dial will increase or decrease the zig
zag width.
Snap on the standard foot.
ZIGZAG STITCHING
22
Stitch length dial
“ and sew 5-6 bartack
“ and sew bar tack
Remove the fabric from under the foot. Pull the upper thread to the
wrong side of the fabric and knot upper and lower threads. Cut the
center of the buttonhole with the seam ripper, being careful not to
cut the stitches on either side.
4. Turn the stitch selection dial to (2, 4) “
stitches.
3. Turn the stitch selection dial to (3) “ “ and sew the left side of
the buttonhole to the mark at the end which is further from you.
2. Turn the stitch selection dial to (2, 4)“
stitches.
To prepare the fabric
Measure the diameter of the button and add 0.3 cm (1/8”) for the
bartacks. If you have a very thick button, add more to the diameter
measurement. Mark the position and length of the buttonhole on the
fabric. Position the fabric so that the needle is on the mark that is
furthest from you. Pull the buttonhole foot towards you as far as it
will go.
Lower the foot.
1. Select buttonhole with the stitch selection dial. Turn the stitch
selection dial to (1) “ “. Sew at moderate speed until you reach
the end mark.
Note: Always test sew a buttonhole.
Preparation
Select buttonhole with the stitch Selection dial.
Snap on The buttonhole foot.
Adjust the stitch length dial between “0.5” - “1”.
The density of the stitch depends on thickness of the fabric.
HOW TO SEW BUTTONHOLES
23
Stitch length dial
Tips
- Slightly reduce upper thread tension to produce a satin stitch on
top.
- Place stabilizer underneath for ¿ne and stretchy fabrics.
- It is best to sew a cord for a buttonhole on a stretch or knit
fabrics. The buttonhole colomns should sew over the cord. (5)
24
Fold the fabric as illustrated with the wrong side up. (2)
Place the fabric under the foot. Turn the handwheel forwards by
hand until the needle swings fully to the left. It should just pierce the
fold of the fabric. (3)
Adjust the guide on the foot (4) by turning the knob (5) so that the
guide just rests against the fold.
Sew slowly, by pressing the foot control lightly guiding the fabric
along the edge of the guide.
Note:
It takes practice to sew blind hems.
Always make a sewing test ¿rst.
For hems, curtains, trousers, skirts, etc.
Select
Blind hem for stretch fabrics.
Select
Blind hem for woven fabrics.
Snap on Blind hem foot. (1)
Stitch length 1.5-2.5
BLIND HEM
25
Wrong side
Stitch length dial
Right side
Set stitch length control between “1” - “4” (according to thickness of
fabric).
The zipper foot is also used to sew cord into a bias strip to form a
piping and to sew the piping into a seam. (3)
To sew past the zipper pull, lower the needle into the fabric, raise
the presser foot and push the zipper pull behind the presser foot.
Lower the foot and continue to sew.
The zipper foot can be snapped onto the right or left, depending on
which side of the foot you are going to place against the zipper or
piping. (2)
Set the machine as illustrated. (1)
ZIPPERS AND PIPING
26
Stitch length dial
When mending tears, it is advisable to use a piece of backing fabric
to reinforce. The stitch density can be varied by adjusting the stitch
length. Begin by sewing over the center and then overlap on both
sides. Depending on the type of fabric and damage, sew between 3
and 5 rows. (B)
To ¿nish edges, stitch along the edge of the fabric.
Set the machine as illustrated. (1)
Patching:
Place the patch in position and stitch around edges.
The stitch length can be shortened to produce very close stitches.
(A)
Sewing on lace and elastic, darning, mending, ¿nishing edges.
3-STEP ZIG-ZAG
27
Stitch length dial
Triple zig-zag: (2)
For hardwearing seams, hems and decorative seams.
Turn the stitch length dial to “S1”.
Triple zig-zag is suitable for ¿rm fabrics like denim, corduroy, etc.
Triple straight stitch: (1)
For reinforced seams.
Turn the stitch length dial to “S1”.
The machine sews two stitches forwards and one stitch backwards.
This gives triple reinforcement.
STITCH SELECTION
28
Stitch length dial
Stitch length dial
Important:
Fabric lint and threads must be removed regularly.
Your machine should be serviced at regular intervals at your local dealer.
Cleaning and lubricating the hook (3)
Remove the bobbin case. Snap the two hook retaining arms (a)
outwards. Remove the hook race cover (b) and the hook (c) and
clean with a soft cloth. Lubricate at the points (d) (1-2 drops) with
sewing machine oil. Turn the handwheel until the hook race (e) is in
the left position. Replace the hook (c). Replace the hook race cover
and snap back the two hook retaining arms. Insert he bobbin case
and bobbin and replace the stitch plate.
Cleaning the feed dog
Remove the bobbin case and use the brush supplied to clean the
whole area.(2)
Remove the stitch plate
Turn the handwheel until the needle is fully raised. Open the hinged
front cover and unscrew the needle plate screw withe the screw
driver.(1)
Attention:
Disconnect the machine from the electricity supply by removing the plug
from the main socket. When cleaning the machine, it must always be
disconnected from the electricity supply.
MAINTENANCE
29
Cause
1. The machine is not threaded correctly.
2. The thread tension is too tight.
3. The thread is too thick for the needle.
4. The needle is not inserted correctly.
5. The thread is wound around the spool holder pin.
6. The needle is damaged.
1. The bobbin case is not inserted correctly.
2. The bobbin case is threaded wrong.
3. The lower thread tension is too tight.
1. The needle is not inserted correctly.
2. The needle is damaged.
3. The wrong size or type of needle has been used.
4. The foot is not attached correctly.
1. The needle is damaged.
2. The needle is not correctly inserted.
3. Wrong needle size for the fabric.
4. The wrong foot is attached.
1. The machine is not correctly threaded.
2. The bobbin case is not correctly threaded.
3. Needle/ fabric/ thread combination is wrong.
4. Thread tension wrong.
1. The needle is too thick for the fabric.
2. The stitch length is incorrectly adjusted.
3. The thread tension is too tight.
1. Poor quality thread.
2. The bobbin case is incorrectly threaded.
3. Fabric has been pulled.
1. The machine must be lubricated.
2. Lint or oil have collected on the hook or needle bar.
3. Poor quality oil has been used.
4. The needle is damaged.
Thread is caught in the hook.
Problem
Upper thread
breaks
Lower thread
breaks
Skipped stitches
Needle breaks
Loose stitches
Seams gather
or pucker
Uneven stitches,
uneven feed
The machine
is noisy
The machine
jams
TROUBLE SHOOTING GUIDE
30
Remove the upper thread and bobbin case, turn the handwheel backwards and forwards by
hand and remove the thread. Lubricate as described.
1. Lubricate as described.
2. Clean the hook and feed dog as described.
3. Only use good quality sewing machine oil.
4. Replace the needle.
1. Select a better quality thread.
2. Remove bobbin case, thread and insert correctly.
3. Do not pull on the fabric while sewing, let it be moved up by the feed dogs.
1. Select a ¿ner needle.
2. Shorten the stitch length.
3. Loosen the thread tension.
1. Check the threading.
2. Thread the bobbin case as illustrated.
3. The needle size must suit the fabric and thread.
4. Correct the thread tension.
1. Insert a new needle
2. Insert the needle correctly. (Àat side towards the back)
3. Choose a needle to suit the thread and fabric.
4. Select the correct foot.
1. Remove and reinsert needle. (Àat side towards the back)
2. Insert a new needle.
3. Choose a needle to suit the thread and fabric.
4. Check and attach correctly.
1. Remove and reinsert the bobbin case and pull on the thread. The thread should pull easily.
2. Check both bobbin and bobbin case.
3. Loosen lower thread tension as described.
1. Rethread the machine.
2. Reduce the thread tension. (lower number)
3. Select a larger needle.
4. Remove and reinsert the needle. (Àat side towards the back)
5. Remove the spool and wind thread onto spool.
6. Replace the needle.
Correction
Please note that on disposal, this product must be
safely recycled in accordance with relevant National
legislation relating to electrical/electronic products.
If in doubt please contact your retailer for guidance
www.husqvarnaviking.com
VSM Group AB • SE-561 84 Huskvarna • SWEDEN
412 97 80 - 26C • English • Inhouse production • © 2005 VSM Group AB • All statements valid at time of printing • Printed in Sweden on environmental-friendly paper •