Sit & Play

Stand & Cruise

1

www.fisher-price.com

Assembled Parts

CAUTION

This product contains small parts in its unassembled state.

Adult assembly is required.

Monkey

Center Arch

Mirror

Ball

Arch End

Tube – 2 Halves

Arch End

Large Ramp

Small Ramp

Elephant

Hippo

Leg

Base

#6 x ¾” Screw – 16

2

Leg

Battery Replacement

1.5V x 3

“AA" (LR6)

For best performance, we recommend replacing the batteries that came with this toy with three, new alkaline “AA” (LR6) batteries.

• Locate the battery compartment on the bottom of the arch.

• Loosen the screws in the battery compartment door with a Phillips screwdriver. Remove the battery compartment door. Remove the exhausted batteries and throw them away.

• Insert three, new “AA” (LR6) alkaline batteries.

Hint: We recommend using alkaline batteries for longer battery life.

• Replace the battery compartment door and tighten the screws with a Phillips screwdriver.

• If this toy begins to operate erratically you may need to reset the electronics. Slide the power/ volume switch off and then back on.

• When sounds or lights from this toy become faint or stop, it’s time for an adult to change the batteries.

• Protect the environment by not disposing of this product with household waste

(2002/96/EC). Check your local authority for recycling advice and facilities (Europe only).

3

Battery Safety Information

In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:

• Do not mix old and new batteries or batteries of different types: alkaline, standard (carbonzinc) or rechargeable (nickel-cadmium).

• Insert batteries as indicated inside the battery compartment.

• Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of product in a fire. The batteries inside may explode or leak.

• Never short-circuit the battery terminals.

• Use only batteries of the same or equivalent type, as recommended.

• Do not charge non-rechargeable batteries.

• Remove rechargeable batteries from the product before charging.

• If removable, rechargeable batteries are used, they are only to be charged under adult supervision.

FCC Statement

United States Only

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.

Note: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

ICES-003

• This Class B digital apparatus complies with Canadian ICES-003.

• Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

4

A Jungle of Fun!

Power/Volume Switch

Balls go in elephant's ears and roll out the trunk

Monkey balances the balls, then sends them down the ramp for music and lights!

Bat the ball for music and lights

Swing the gator for music and lights

Spin the hippo for peek-a-boo fun

• Slide the power/volume switch under the arch to on with low volume , on with high volume or, when finished playing, slide the switch off .

5

Consumer Information

• Please keep this instruction sheet for future reference, as it contains important information.

• Adult assembly is required.

• Requires three “AA” batteries for operation (included).

• Tool required for assembly: Phillips screwdriver (not included).

• Wipe this toy with a clean cloth dampened with a mild soap and water solution.

• Do not immerse this toy.

• This toy has no consumer serviceable parts. Do not take the toy apart.

Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A.

©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.

N1415pr-0920

PRINTED IN MEXICO

Assembly

Base

Legs

1

• Fit each leg onto the base.

Note: Each leg only fits one way to the base.

If it does not seem to fit, try the other side of the base.

• Insert four screws into the holes in the base and tighten.

• Turn the base upright.

2

• Fit the tube halves together. Push to “snap” them in place.

Arch Ends

Elephant Hippo

9

• “Snap” the elephant and hippo into the base assembly, as shown.

Center Arch

10

• Note: We recommend replacing the batteries in the arch before assembling it to the base. Refer to the Battery

Replacement section on this sheet.

• Fit each arch end onto the center piece.

• Insert two screws on each end.

Tighten the screws.

7

Assembly

Tube

Small

Ramp

Tube

Base

3

• Insert and “snap” the tube into the base.

Note: The tube only fits into the base one way. If it does not seem to fit, turn it around and try again.

4

• Slide the small ramp onto the tube.

• Turn the small ramp until it reaches the base.

Screws

Arch Assembly

Screws

11

• Turn the arch assembly upright.

• Fit the center of the arch assembly onto the tube. Push to “snap” in place.

• Fit the ends of the arch assembly onto the elephant and hippo. Push to "snap" in place.

Note: The arch assembly only fits one way.

If it does not seem to fit, turn it around and try again.

8

12

• Insert three screws into the holes on top of the elephant and the hippo. Tighten the screws.

Assembly

Small

Ramp

Large

Ramp

Tube

Small

Ramp

Slot

5

• Insert the tab on the end of the small ramp into the slot in the base. Push to “snap” in place.

6

• Slide the large ramp onto the tube.

• Turn the large ramp until it reaches the top of the small ramp.

Mirror Toy

13

• Insert a screw up through the hole in the large ramp and into the arch assembly.

Tighten the screw.

14

• Remove the film from the mirror toy.

• Insert and “snap” the mirror toy into the hole in the arch above the elephant.

9

Assembly

Large

Ramp

Small

Ramp

Screw

7

• Insert the tab on the end of the large ramp into the slot in the small ramp. Press the ends to “snap” them together.

8

• Insert a screw into the hole under the large ramp and tighten.

Monkey

15

• Insert and “snap” the monkey into the center of the arch assembly.

T-Loop

Ball

16

• Locate the strap on the arch assembly.

• Insert the T-loop end of the strap into the slot in the ball.

• Pull on the strap to make sure the ball is secure.

10