advertisement
Product Registration
HAAN
®
Corporation
1828 William Penn Way
Lancaster, PA 17601
Place
Stamp
Here
Instruction Manual
name:
Multiforce Plus™
model number:
SS-23
“First of its kind steam cleaner with high velocity
CR-motion
™
technology.”
NORMAL TURBO
STEAM
HAAN
®
Corporation
1828 William Penn Way
Lancaster, PA 17601
phone:
877-422-6347
www.HAANusa.com
SS23_IS0021
Copyright ©2012 HAAN
®
Corporation
Notice
The information contained in this document is subject to change without notice.
HAAN
®
Corporation assumes no responsibility for any errors that may appear in this document nor does it make expressed or implied warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
HAAN
®
Corporation shall not be liable for incidental or consequential damages in connection with or arising out of the furnishing, performance, or use of this document and the program materials which it describes.
All rights reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent of HAAN
®
Corporation.
HAAN
®
is a registered trademark of the HAAN
®
Corporation.
HAAN
®
Experience Steam. Discover Clean.
™ is a trademark of the HAAN
®
Corporation.
(Fold here and tape closed before mailing)
Product Specifications: Model SS-23
Color
Size
Weight
Voltage/Hz
Wattage
Cord Length
Tank Capacity
Heat-up Time
Operating Time
grey and Red
10.27” W x 9.8” D x 47.24” H
6.94 lb
AC 120V, 60Hz
1200 watts
18 feet
11.83 fl. oz.
40-45 sec.
20 min. (High Setting) 29 min. (gentle Setting)
*Dimensions approximated. Dimensions include base and measured without hose, or attachments.
One-Year Limited Warranty
Your HAAN® Steamer is warranted to be free from defects in material and workmanship for a period of one (1) year from the date of purchase when utilized for normal household use by the original purchaser only. The included Warranty Registration
Card should be filled out and returned within thirty (30) days of purchase. This will register your product.
Should any defect covered by the terms of the limited warranty be discovered within one year, HAAN® Corporation will repair or replace the defective part. To process a warranty claim, contact customer care at 1-877-422-6347 for further assistance and instructions. A customer care agent will conduct trouble shooting in an attempt to fix any minor problems. Should trouble shooting not provide any result, a return authorization will be issued. Proof of purchase is required and should accompany the return.
Freight costs must be prepaid by the purchaser.
The liability under this warranty is limited solely to the cost of the replacement parts or the complete unit at our option. Labor charges are not included.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of HAAN® Corporation, if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is HAAN® Corporation liable for incidental or consequential damages of any nature whatsoever. Some states/provinces do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you. This warranty gives you specific legal rights which vary from state to state or province to province.
Warranty Notice: failure to complete and return the product registration card will not diminish your warranty rights.
Introduction
Congratulations on purchasing a nate, linoleum and vinyl floors.
HAAN
®
product. Now you have an easy way to clean your tile, hardwood, lami-
The multiforce Plus™ uses steam to remove tough grease, dirt and grime. Steam is nature’s purest and most powerful cleaner for all hard surfaces in your home.
The multiforce Plus™ also uses CR-motion
™
technology.
This technology uses the power of reciprocating motion to further enhance the cleaning power of steam.
HAAN
®
products are so easy to assemble, you can put them to use right away – anywhere you want to clean and sanitize – from your kitchen and living room to your bathroom floors and outdoor surfaces.
Backed with a one-year limited warranty, your quality
HAAN
®
product is sure to give you years of dependability. And our Customer Care representatives are available to answer any of your questions about your new floor sanitizer.
Thousands of
HAAN
®
customers have already fallen in love with will, too.
HAAN
®
floor Sanitizers. We’re confident you
Thank you again for purchasing a
HAAN
®
.
The
HAAN
®
Team
1
IMPOrTANT SAFeTY INSTruCTIONS
WArNiNg
When using the Multiforce Plus™ basic safety precautions should always be observed, including the following:
reAD ALL INSTruCTIONS BeFOre uSING
(THIS APPLIANCe)
CAUTiON
The Multiforce Plus™ emits steam at 212˚F to sanitize the area of use. This means that the steam head, ultra-Microfiber Pads,
Scrub Brushes and
Carpet Glide get very hot during use. Care should be taken when using this appliance.
DO NOT touch them during use except in the approved manner as outlined in this manual.
SAVE THESE
INSTRUCTIONS: for household use only.
Any other use of this appliance will void the manufacturer’s warranty.
2
WArNiNg risk of electrical shock: Be sure to read and follow all instructions and warnings.
WArNiNg
To reduce the risk of fire, electric shock, or injury:
9.
10.
7.
8.
11.
12.
13.
6.
4.
5.
1.
2.
3. use the system only for its intended use.
Do not leave the multiforce Plus™ unattended when plugged in. Turn it off and unplug the electrical cord from the outlet when not in use.
Do not allow to be used as a toy. Pay close attention when used near children, pets or plants. Do not leave the multiforce Plus™ unattended while plugged in.
use only as described in this manual.
use only manufacturer’s recommended accessories.
Do not operate the multiforce Plus™ with a damaged plug or cord. Do not use it if the multiforce Plus™ has been dropped or damaged.
To avoid the risk of electric shock do not disassemble or attempt to repair it on your own. incorrect re-assembly or repair can cause a risk of electric shock or injury to persons when the multiforce Plus™ is used.
To protect against a risk of electric shock, do not immerse the multiforce Plus™ into water or any other liquid.
Do not pull or carry by power cord, use cord as handle, close a door on cord, or pull cord around sharp edges or corners. Keep cord away from heated surfaces.
Do not unplug by pulling on power cord. To unplug, grasp the plug not the cord. Do not use extension cords or outlets with inadequate current capacity.
Turn the unit off before unplugging from electrical outlet.
Do not handle plug or the multiforce Plus™ with wet hands or operate it without shoes.
Do not put foreign objects into openings. Do not use with any opening blocked.
Do not put hands or feet under the multiforce Plus™. It gets very hot.
19
Notes
18
Important Safety Instructions
25.
26.
27.
20.
21.
22.
23.
24.
17.
18.
19.
14.
15.
16.
32.
33.
34.
28.
29.
30.
31. use
ONLY
on flat, horizontal surfaces. Do not use on walls, counters or windows.
Do not add cleaning solutions, scented perfumes, oils or any other chemicals to the water used in the multiforce Plus™ as this may damage it or make it unsafe for use. use regular tap water or distilled purified water if the tap water in your area is very hard.
When in use, never turn the multiforce Plus™ over or on its side.
Never direct steam towards people, animals or plants.
Do not handle the ultra-microfiber pads immediately after turning the multiforce Plus™ off. Place the multiforce Plus™ on the floor protector pad to cool down before removing.
Never leave the Multiforce Plus™ steaming in one spot on any surface for any period of time. Always place on the floor protector pad and make sure that the Multiforce Plus™ is turned off.
When cleaning the multiforce Plus™, turn if off and clean with a dry or damp cloth. Do not pour water or use alcohol, benzene or turpentine on the unit.
Extreme caution should be exercised when using the multiforce Plus™ to clean stairs.
Never use the multiforce Plus™ without the ultra-microfiber cleaning pads, polish pads, scrub brushes or carpet glide attached.
Keep your work area well lit.
Store the multiforce Plus™ in doors in a cool, dry place.
Do not open the water tank cap to refill or empty the water tank when power is turned on.
Do not bend the power cord excessively or place heavy objects on the power cord.
if the power cord has become knotted and or worn contact the service center for replacement power cord.
Do not operate the multiforce Plus™ if the power indicator lamp flickers. Contact the Customer Care at 877-422-6347.
Always properly insert the power cord in to the cord hanger when in use.
To protect the power cord, coil the power cord over two cord racks (upper and lower) loosely for storage when not in use.
Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
Connect to a properly grounded outlet only. See grounding instructions.
Do not use CR-motion™ with Carpet glide.
WARNiNg - To reduce the risk of fire, use only commercially available floor cleaners and waxes intended for machine application.
Connect to a properly grounded outlet only.
See grounding instructions.
WArNiNg
DO NOT use Crmotion™ when Carpet
Glide is attached to product. Doing so could result in product malfunction or product failure.
WArNiNg
Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where combustible liquids may be present.
3
IMPOrTANTeS MeSureS De SéCurITe
L’utilisation d’un appareil électrique demande certaines précautions, dont les suivantes:
LIre TOuTeS LeS INSTruCTIONS AVANT
D’uTILISer (CeT APPAreIL)
AVErTiSSEMENT: pour réduire le risque d’incendie, de choc électrique ou de blessure:
1. Ne pas laisser l’apparecil sans surveillance lorsqu’il est branché. Le débrancher lorsqu’il n’est pas utilisé et avant le dépannage.
2. Ne pas laisser les enfants jouer avec l’appareil ou s’en servir sans surveillance. Redoubler d’attention s’il y a des enfants á proximite lorsqu’on utilise l’appareil.
3. utiliser l’appareil en respectant les consignes de celte notice d’emploi et n’utiliser que les accessoires recommandés par le fabricant.
4. Ne pas utiliser l’appareil si le cordon ou la fiche est endommagé. Retoumer l’appareil á un atelier de réparation s’il ne fonctionne pas normalement, s’il a été
échappé, s’il est endommagé, s’il a été oublié á l’extérieur ou immergé.
5. Le cordon ne doit pas étre utilisé comme une poignée ou pour tirer, trainer ou soulever l’appareil. Ne pas faire passer l’appareil sur le cordon ; ne pas coincer le cordon dans l’embrasure en refermant les portes ni tierer dessus á l’angle d’un mur ou d’une autre aréte vive et le tenir á distance des surfaces chaudes.
6. Ne pas tirer sur le cordon pour débrancher l’appareil; tirer plutót sur la fiche.
7. Ne pas toucher la fiche du cordon ou l’appareil avec les mains humides.
8. Ne pas insérer d’objet dans une ouverture quelconque de l’appareil. Ne pas utiliser l’appareil lorsqu’une ouverture est blogquée et enlever la poussiére. la peluche, les cheveux, etc., qui peuvent gener le débit d’air.
9. Veiller á bien se garder - doigts, cheveux, vétements amples - á distance des ouvertures des pieces mobiles.
10. mettre toutes les commandes en position d’arrét avant de débrancher l’appareil.
11. Redoubler d’attention en nettoyant les escaliers.
12. Ne pas se servir de l’appareil pour aspirer des laquides combustibles ou inflammables comme de l’essence ou dans un endroit oú il peut y avoir de tels liquides.
13. Doit être branché sur une prise de courant avec mise à la terre. Voir les instructions de mise à la terre.
4
14. Pour réduire le risque du feu, employez seulement les décapants disponibles dans le commerce et les cires de plancher destinés pour l’application de machine.
CONSerVer CeS INSTruCTIONS
Commonly Asked Questions
Q: Can the Multiforce Plus™ be used on laminate flooring?
A: yes. The multiforce Plus™ was designed to be gentle on delicate flooring, yet powerful enough to penetrate stains and kill harmful germs and bacteria.
it is recommended that the flooring manufacturer be contacted to see if it is oK to clean the floor with steam. Leaving the steam mop sitting in one spot while steaming could result in discoloration of flooring.
Q: How long can an Ultra-microfiber Pad be used until it needs to be changed?
A: The pad should be changed every 10 minutes, or when it becomes saturated with water. The unit will become harder to push with a overly wet pad.
Q: How long does a tank of water last?
A: A full tank will last approximately 20 minutes.
Q: Sometimes my floor sanitizer becomes hard to push - why?
A: if the unit is hard to push its likely because the ultra-microfiber Pad is too wet or the angle at which you are using the machine is too high.
Q: How do you use the Carpet Glide for my carpet?
A: The carpet glide is to be used without the ultra-microfiber Pads or Scrub Brushes and can be attached directly to the unit. Do NoT use CR-motion
™
when the Carpet glide is attached.
Q: Does the HAAN work on pet stains?
A: yes, the HAAN is able to spot clean fresh pet stains by loosening and lifting the stain.
Q: How can I prolong the life of my HAAN?
A: To maintain the life of your unit, we recommend using the fresh Rinse once a month.
Q: Will the HAAN Floor Sanitizer clean grout?
A: yes, but it needs a little help. if you glide your HAAN over the problem areas and then scrub with your ultra-microfiber Pad, it should effectively clean your grout.
Couldn’t find the Answer to your Question?
Call Customer Care at 877-HAAN DIreCT / 877-422-6347
17
16
To order additional pads, accessories or replacement parts call customer care at:
877-HAAN DIRECT / 877-422-6347
Or visit:
www.HAANusa.com
Operating Instructions iMPOrTANT
Care & Maintenance
Always ensure that the
Multiforce Plus™ is UN-
PLUGGED from the wall receptacle prior to cleaning or emptying the water
tank.
CAUTiON
Do not immerse the
Multiforce Plus™ in water or any other liquid.
CAUTiON
Always operate the
Multiforce Plus™ by gripping the handle.
Do not grip by the pole.
SAVe THeSe
INSTruCTIONS | FOr
HOuSeHOLD uSe
Commercial use of this unit voids the manufacturer’s warranty.
6.
7.
5.
4.
1.
2.
3.
Turn the multiforce Plus™ off and unplug from the electrical outlet.
Wrap power cord around cord hangers.
Let the multiforce Plus™ cool for five (5) minutes before removing the ultra-microfiber pads and before emptying the water tank.
Always empty the water tank when you have finished using the multiforce Plus™.
Never leave ultra-microfiber pads on the multiforce Plus™ when you have finished using it. Always remove the ultra-microfiber pads and wash in warm water with a mild detergent.
Never use bleach or fabric softener when cleaning the ultra-microfiber pads.
The ultra-microfiber pads can be washed in a washing machine and dried in a clothes dryer but on low heat.
To decrease pad wear, we recommend the pads be hung to dry for 24 hours.
Wipe the multiforce Plus™ with a damp cloth to clean. Never immerse the multiforce Plus™ in water or any other liquid.
in order to keep the multiforce Plus™ in good condition, we recommend that you clean the water tank once a month to eliminate calcium deposits. Add eight ounces (8 oz) of water to the water tank and insert 1 packet of fresh
Rinse™ Lime and Scale Remover. Shake to loosen any deposits. Place unit on resting mat without pads, turn unit on and allow water to steam until water in tank is depleted. Do
not use vinegar or other decalcifying substances in the floor sanitizer water tank.
Helpful Hints
3.
4.
1.
2.
5.
The easiest way to use the machine is to tilt the handle to a 45º angle and clean slowly 2-3 yards at a time.
Hand wash or machine wash the ultra-microfiber pads in the delicate cycle with a mild detergent.
We recommend air drying the ultra-microfiber pads for 24 hours, but they could be dried in a dryer on a low heat setting.
A good amount of steam passes through the ultra-microfiber pads. We recommend that the ultra-microfiber pads be changed when it becomes oversaturated.
To remove stubborn stains from vinyl or linoleum floors, pre-treat with a mild detergent and some water before using the floor sanitizer.
IMPOrTANT: Never leave the Multiforce Plus™ steaming in one spot on any surface for any period of time.Always place on the floor protector pad and make sure that the floor sanitizer is turned off.
5
ADDITIONAL IMPOrTANT SAFeGuArDS
1.
2.
3.
To avoid circuit overload, do not operate another appliance on the same electrical outlet (circuit).
if an extension cord is absolutely necessary, a 15 amp 16 gauge cord should be used. Cords rated for less average may overheat. Care should be taken to arrange cord so that it cannot be pulled or tripped over.
Do not leave unattended when the system is connected to a power supply electrical outlet.
A) For all grounded, cord-connected appliances: grOUNdiNg iNSTrUCTiONS:
This appliance must be grounded. if it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNiNg - improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
1) This appliance is for use on a nominal 120-V circuit, and has a grounded plug that looks like the plug illustrated in sketch “A”. A temporary adaptor should be used only until a properly grounded outlet (sketch “A”) can be installed by a qualified electrician. The green colored rigid ear, lug, or the like extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by a metal screw.
2) This appliance is for use on a nominal 120-V circuit and has a grounding attachment plug that looks like the plug illustrated in sketch “A”. make sure that the appliance is connected to an outlet having the same configuration as the plug. No adaptor should be used with this appliance.
Troubleshooting
Problem
unit not operating.
unit does not emit steam.
Water left on floor.
White spot left on floor.
Solution
• Ensure plug is set firmly in outlet.
• Replace fuse or reset breaker.
• Ensure water tank is filled with water.
• Change the Ultra-microfiber pad.
• Ensure unit is always level and parallel to the floor.
• When cleaning do not leave unit in one spot for too long.
• Use protector pad / floor mat when unit is ON and stationary.
• Use distilled water instead of hard tap water.
NOTe: To remove spot, use a damp cloth with a few drops of white vinegar to rub and remove stain.
6 15
using the Carpet Glide
NOTE:
The Carpet glide is used WiTHouT the Pads or Scrub Brushes.
What is the Carpet glide?
The carpet glide enables the multiforce Plus™ to freshen, deodorize and sanitize carpeting, rugs, upholstery, pet cushions and more. used with the multiforce Plus™ it kills dust mites and other allergens on a variety of surfaces.
WArNiNg
DO NOT use Cr-motion™ when Carpet Glide is attached to unit. Doing so could result in product malfunction or product failure.
1 2
3
To Remove
Carpet Glide
TAB
TAB
“Hands Free”
Removal Tab
Attach carpet glide by placing unit under “tabs” and gently pushing down into place.
With carpet glide attached, place on Floor Protector / Resting Mat.
Turn Steam oN and follow operating instructions to clean.
Turn unit off, let cool. use foot on “Hands free” tab to remove Tray from steam head.
using the Carpet Glide - FOr FreSH STAINS
1 2 3
“Hands Free”
Removal Tab
A) Tous les appareils mis á la terre et munis d’u cordon: iNSTrUCTiONS dE MiSE A LA TErrE
Cet appareil doit étre mis à la terre. En cas de défaillance ou de panne, le circuit de mise à la terre offre au courant un chemin de moindre résistance qui réduit le risque de choc électrique.
L’appareil est pourvu d’un cordon muni d’un conducteur qui en assure la mise à la terre et d’une fiche avec broche de terre. Cette fiche doit étre branchée sur une prise convenable, correctement installée et reliée à la terre conformément aux codes et aux réglements du lieu.
AVERTiSSEmENT - un conducteur de terre mal raccordé présente des risques de choc électrique. Consulter un électrician ou un technicien d’entretien compétent en cas de doute à propos de la mise à la terre d’une prise quelconque. Ne pas modifier la fiche vendue avec l’appareil; si ele ne s’insére pas daris la prise, faire installer une nouvelle prise par un électricien compétent.
1) Cet appareil destiné à un circuit nominal de 120 V est muni d’une fiche de terre semblable à celle illustrée dans le croquis A. un adaptateur temporaire ne devrait étre utilisé qu’en attendant l’installation, par un électricien compétent, d’une prise correctement mise à la terre (croquis A).
L’oreillette rigide, le crochet ou autre dispositil de couleur verte intégré à l’adaptateur doit étre connecté à un element correctement relié à la terre, par exemple le couvercle d’une bolte de sortie mise à la terre, et il doit étre fixé à la prise au moyen d’une vis métallique.
2) Cet appareil destiné à un circuit nominal de 120 V est muni d’une fiche de terre semblabie à ceile illustrée dans le croquis A. L’appareil doit étre branché sur une prise ayant la méme confguration que la fiche. Aucun adaptateur ne davrait étre utilisé avec cet appareil.
Place unit on stain. Let stand for a few seconds. Allow steam to saturate stain.
4
Slowly move unit back and forth over stain.
5
Remove carpet glide from unit with hands free tab.
6
gently place unit on ultra-microfiber cleaning pads.
14
use the pad to rub the area
“blotting” out the stain.
Turn unit off. When cooled, remove ultra-microfiber pads.
7
ultra-Microfiber Pads for HAAN
®
Multiforce Plus™
What is an ultra-microfiber?
An ultra-microfiber is a textile fiber that is thinner and more absorbent than a microfiber (1.0dtex) pad typically used with steam mops. Specifically, to be defined as an ultra-microfiber, it should be less than 0.2dtex. The ultra-microfiber pad by HAAN
®
Corporation is made of .17dtex ultra-microfibers.
How to Use Ultra-Microfiber Pads
3.
4.
1.
2.
Please make sure that a completely dry pad is used.
As high temperature steam passes through a pad to contact the floor to kill germs, molds, mites and to provide a certain amount of water necessary for cleaning, it is natural that the pad gradually absorbs moisture. After a certain length of time, the pad repels water and becomes damp.
To keep the floor clean and dry, replace the pad when it is dirty.
only remove pad from unit when not in use and steam is not being emitted.
How to Clean and Store
1.
2.
3.
Hand wash or machine wash the ultra-microfiber pad in cold water on the delicate cycle with a mild detergent. (Do not use a fabric softener) using a washing machine may shorten the lifespan of the pads.
We recommend air drying the ultra-microfiber pad for 24 hours, but they could be dried in a dryer on a low heat setting.
Chlorate bleach
Hanger Lightly
About HAAN’s Cr-motion
™
Technology
Steam, Scrub, Buff and Polish - All in One Machine.
The multiforce Plus™’s ability to clean so effectively lies in the design of its steam distribution system, CR-motion™. Two reciprocating pads moving in opposite directions of one another provides a back-and-fourth motion that utilizes the power of steam to clean. Each pad has 10 steam jets that provide a continuous flow of 212º steam. The steam jets are strategically positioned on the pads to produce a consistent flow of high temperature steam from one end of the pad to the other. The multiforce Plus™’s
CR-motion™ technology enhances the natural pull-and-push motion of standard steam mops and takes steam cleaning to a whole new level.
To Steam, or Not to Steam - it’s your choice.
The multiforce Plus™ offers a number of cleaning options:
1.
2.
3.
Steam can be used without CR-motion
CR-motion
™
™
can be used without steam.
.
Steam and CR-motion™ can be used simultaneously.
8
10 11
iMPOrTANT:
Vibration Sound
During use it’s normal to hear a “clicking” sound coming from the unit. This sound is produced by the water being pumped through the unit.
Place unit with pads/scrub brushes attached onto floor
Protector / Resting Mat. Allow to cool down for five (5) min.
When unit has cooled, remove pads or scrub brushes. Store unit upright in a dry area.
iMPOrTANT
Always empty the water tank once you have finished using the multiforce Plus™.
iMPOrTANT
When removing the pads or scrub brushes from the unit Do
NoT turn unit upright or on its side. ALWAyS lift unit uP off the pads or scrub brushes.
Floor Setting Button
use this button to switch between two steam levels, normal & turbo. Each caters to specific floor types.
Floor Setting indicator Light
red
Light
=
High steam emission ideal for ceramic, stone, tile and other durable floors.
This light indicates which steam floor setting level is selected.
Green
Light
=
gentle steam emission perfect for sealed hardwood, laminate, bamboo and other delicate floors.
floor Setting
Control
NORMAL TURBO floor Setting indicator Light
STEAM
Cleaning Pads and Scrub Brush Attachments
Buffing Pads
ideal when using CR-motion
™
without steam. Can be used with a floor agent to polish and shine. See page 8 for care instructions.
NOTe: it may be helpful to apply the floor agent with the ultra-microfiber Cleaning Pads and finish with the Buffing Pads
Do not use on unsealed wood or unglazed ceramic floors. on surfaces that have been treated with wax or some no-wax floors, the sheen may be removed by heat and steam. it is always recommended to test an isolated area of the surface to be cleaned before proceeding. We also recommend that you check the use and care instructions from the floor manufacturer.
Ultra-Microfiber Cleaning Pads
ideal when using the steam function by itself or with CRmotion™ activated. great for cleaning laminate, hardwood, tile and vinyl surfaces. Can also be used to “blot” fresh stains on carpet. See page 8 for care instructions.
Scrub Brush Attachments
ideal when using CR-motion™ with or without steam. great for outdoor use on decks, patios and walkways. Best when used with a cleaning agent. To clean Scrub Brush
Attachments rinse with water.
13
using the Multiforce Plus™ - Operating Instructions
The multiforce Plus™ offers a number of cleaning options:
1.
2.
3.
Steam can be used without CR-motion
CR-motion
™
™
can be used without steam.
.
Steam and CR-motion™ can be used simultaneously.
1 2 3
Assemble unit and place on
Floor Protector / Resting Mat.
4
Press Water Tank Release button and remove water tank.
5
Turn Cap counterclockwise to remove. fill tank with water.
6
Product Assembly & Parts
A
1
2
CLiCK!
B
Handle Assembly
CLiCK!
Pole Assembly
Tighten cap. insert tank (cap down) until it “clicks”.
7
NORMAL URBO
STEAM
TO STeAM: Press ON/OFF button. Wait 40-45 seconds for unit to heat up. unit may vibrate while heating.
8
Line up pads or scrub brushes. gently place unit on pads or scrub brushes. you are now ready to steam, buff or scrub.
9
17
3
4 STEAM
10
11
12
13
14
PUSH
15
5
6
7
8
9
16
O
F
PA
D OF
F
PA
D
STEAM
TO ACTIVATe Cr-motion:
Using foot press ON/OFF button.
Tilt handle at a 45º angle.
Push and pull slowly across the floor to clean thoroughly.
When done, push CR-motion
ON/OFF Button and Steam
ON/OFF Button.
Operating Instructions Continued on Next Page
12
1. Handle • 2. Pole • 3. Floor Setting Indicator Light • 4. Steam Power Switch
5. Storage Hook (rotates 360º) • 6. Power Cord Organizer (bottom)
7. Power Cord • 8. Water Tank release Button • 9. Detachable Water Tank
10. Floor Protector / resting Mat • 11. Carpet Glide • 12. Buffing Pads (1 set)
13. Ultra-Microfiber Cleaning Pads (4 sets) • 14. Scrub Brush Attachment (1 set)
15. Fresh rinse Lime & Scale remover (x12)
16. CR-motion™ On/Off Button • 17. Floor Setting Control
9
Before using the Multiforce Plus™
Be sure to read ALL instructions and warnings before using the Multiforce Plus™.
WArNiNg
The Multiforce Plus™ is designed to clean hard floor surfaces that will withstand high heat. Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax or some no-wax floors, the sheen may be removed by the heat and steam. It is always recommended to test an isolated area of the surface to be cleaned before proceeding. We also recommend that you check the use and care instructions from the floor manufacturer.
CAUTiON
use only a heavy duty extension cord rated for 15 amps minimum – DO NOT use an ordinary extension cord.
iMPOrTANT
This product is NOT for space heating purposes.
CAUTiON
HAAN
®
floor care products emit steam at 212º to sanitize the area of use. This means that the steam head, ultra-microfiber pads, scrubbing brushes and carpet glide get very hot during use. Care should be taken when using this appliance and
DO NOT touch components of this machine during use except in the approved manner as outlined in this manual.
Helpful Hint:
When heated, never leave the appliance in one spot on any surface for any period of time. Always place the multiforce Plus™ on the Floor Protector/Resting Mat when stationary.
Helpful Hint:
To extend the life of your ultra-microfiber
Pads, always place your unit on the floor protector/resting mat while the unit heats up. Attach the ultra-microfiber pads when the unit is ready to use.
Helpful Hint:
Always empty water from water tank after use. To ensure optimum product function use fresh Rinse
™
once a month.
Helpful Hint:
When using the multiforce Plus™ with the Carpet glide it will not lift all set-in stains from your carpet. our patented ultra-microfiber pads may be used to act as a “blotter” for removing most fresh, wet spills and stains.
Before using the Multiforce Plus™ (continued)
COrrECT PAd PLACEMENT
10
11
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement