HISTORY INFORMATION FOR THE FOLLOWING MANUAL:
SERVICE MANUAL
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
ORIGINAL MANUAL ISSUE DATE: 2/2012
AZ3WK CHASSIS
Segment: P-2F
Version
1.0
1.1
Date
2/2012
2/2012
Subject
Original manual issue.
Added part number of Insulation sheet G. (P.22)
LCD Digital Color TV
9-888-459-02
SERVICE MANUAL
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
AZ3WK CHASSIS
Segment: P-2F
LCD Digital Color TV
9-888-459-02
MODEL LIST
MODEL
KLV-32BX350
COLOR
Black
COMMANDER
RM-SA022
DEST.
CHINA
KLV-40BX450
Black
RM-SA022
CHINA
KLV-46BX450
Black
RM-SA022
CHINA
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
MODEL
COLOR
COMMANDER
DEST.
3
型号表
型号
颜色
遥控器
地区.
KLV-32BX350
黑色
RM-SA022
中国
KLV-40BX450
黑色
RM-SA022
中国
KLV-46BX450
黑色
RM-SA022
中国
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
型号
颜色
遥控器
地区
3
WARNINGS AND CAUTIONS
- ENGLISH
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
WARNING!!
An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis.
The chassis of this receiver is directly connected to the ac power line.
CARRYING THE TV
Be sure to follow these guidelines to protect your property and avoid causing serious injury.
• Carry the TV with an adequate number of people; larger size TVs require two or more people.
• Correct hand placement while carrying the TV is very important for safety and to avoid damages.
SAFETY-RELATED COMPONENT WARNING!!
Components identified by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony
parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identified in this manual.
Follow these procedures whenever critical components are replaced or improper operation is suspected.
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
4
警告与注意
注意
维修使用说明仅限于有资质的维修人员使用。
为降低触电的风险,请不要进行使用说明书内容以外的检修,除非你可以胜任。
警告!!
检修时请务必使用隔离变压器,以避免因机壳带电引起触电。
接收器机壳直接连接在交流电源线上。
电视机运输
务必遵循这些指导来保护你的财产和避免造成严重伤害。
• 运送电视机需要足够的人手;大尺寸的电视机需要两人或更多的人
•搬运时把手放置在正确的位置对电视机的安全及避免损坏是非常重要的。
相关安全部件警告!!
在示意图, 分解图, 和零件清单上用阴影标识的部件对安全操作很关键. 用本手册或SONY增补手册上出现零件号码的零件来替换这些部件。
无论何时,替换关键部件或出现疑似不正确操作时,都要遵循本流程。
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
4
WARNINGS AND CAUTIONS
USE CAUTION WHEN HANDLING THE LCD PANEL
When repairing the LCD panel, be sure you are grounded by using a wrist band.
When repairing the LCD panel on the wall, the LCD panel must be secured using the 4 mounting holes on the rear cover.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Do not press on the panel or frame edge to avoid the risk of electric shock.
Do not scratch or press on the panel with any sharp objects.
Do not leave the module in high temperatures or in areas of high humidity for an extended period of time.
Do not expose the LCD panel to direct sunlight.
Avoid contact with water. It may cause a short circuit within the module.
Disconnect the AC power when replacing the backlight (CCFL) or inverter circuit. (High voltage occurs at the inverter circuit at 650Vrms.)
Always clean the LCD panel with a soft cloth material.
Use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short.
Protect the panel from ESD to avoid damaging the electronic circuit (C-MOS).
It is recommended not to exceed 1 hour of Power-On nor Burn-in period with LCD panel face down condition, in repair activity.
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
5
警告与注意
搬运液晶显示屏时请务必小心
修理液晶显示屏时,请务必佩戴静电手环。
修理挂壁液晶显示屏时,液晶显示屏必需用后盖上的4个固定孔保护。
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
不要按压到液晶屏或面框边缘以避免电击风险。
不要用任何尖锐物品在液晶屏上刮擦或按压。
不要让组件长期处在高温或高湿度环境中。
不要让LCD液晶屏暴露在直射阳光中。
避免与水接触。它可能引起组件内部短路。
当更换背光灯(冷阴极荧光灯管) 或 逆变器(逆变器的高压输出会有650Vrms。)时,断开交流电源。
要经常清洁液晶屏的话请用软布材料。
当处理逆变器的线路或连接时,要小心。线路的损坏可能引起短路。
用ESD保护液晶屏以免损坏电子电路 (C-MOS)。
在维修期间,LCD 液晶屏面朝下的情况下,建议不要上电超过一小时或老化期间。
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
5
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer.
7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
8. For safety reasons, repairing the Power board and/or Inverter board is prohibited.
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
6
安全检测
故障维修完成后,在交付给用户前必须进行下列检查:
1. 检查所维修位置是否还有为焊接或焊接不良的地方。检查整个面板表面是否存在任何焊渣或焊桥。
2. 检查面板面板内部布线,确保线路未扭绞在一起或者与高瓦特(功率)的电阻接触。
3. 检查是否需要更换所有的控制按钮,屏蔽线,外壳,接地线以及固定部件。务必保障在更换后是绝缘的。
4. 检查需要更换的部件,尤其是在以往维修时安装的电子元件。此时,须向用户说明此情况,并建议更换。
5. 查找虽在运行,但其性能已明显老化迹象的部件。此时,须向用户说明此情况,并建议更换。
6. 检查线路是否有破裂或磨损,如有则建议用户进行更换。
7. 检查天线端子、金属装饰条、镀金属的旋钮、螺丝以及所有外露的金属部件是否漏电。检查步骤参照下面说明进行。
8. 为了安全起见,禁止修复电源板与逆变器中任意一个。
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
6
SAFETY CHECK-OUT
Leakage Test
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed
metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’
instructions to use these instructions.
2. A battery-operated AC milliampmeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The
“limit” indication is 0.75 V, so analog meters must have an accurate low voltage scale.
The Simpson’s 250 and Sanwa SH-63TRD are examples of passive VOMs that are suitable. Nearly all
battery-operated digital multimeters that have a 2 VAC range are suitable (see Figure A).
How to Find a Good Earth Ground
A cold-water pipe is a guaranteed earth ground; the cover-plate retaining screw on most AC outlet boxes is also
at earth ground.
If the retaining screw is to be used as your earth ground, verify that it is at ground by measuring the resistance
between it and a cold-water pipe with an ohmmeter. The reading should be zero ohms.
If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble- light (not a neon lamp) between the hot
side of the receptacle and the retaining screw. Try both slots, if necessary, to locate the hot side on the line; the
lamp should light at normal brilliance if the screw is at ground potential (see Figure B).
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
7
安全检测
漏电检测
从任何外露金属部分到接地,以及从所有外露金属部分到其他外露部分再回到底座之间的漏电电流不得超过
0.5mA。可使用下列三种方法的任意一个去检测漏电:
1. 商用检漏仪,例如 Simpson 229 或 RCA WT540A。按照制造商的指导操作使用。
2. 电池供电的交流毫安计,可使用 Data Precision 245 数字毫安计。
3. 使用VOM(伏特-欧姆计)或电池供电的交流伏特表测量电阻器降压。“限值”为0.75V,因此模拟仪表必需具
有精确的低压刻度。Simpson 250 和 Sanwa SH-63Trd 均为无电源VOM量表,十分适用。几乎所有电池供电的
数字毫安计都具有2V的交流范围,都适用进行测量(如图A所示)。
怎样找到一个好的接地点
冷水管是一种有保证的接地设备; 交流电插座盒盖板的固位螺丝同样是接地的。
如果要把固位螺丝用来接地, 应先用欧姆表测量固位螺丝与冷水管之间的电阻,如果读数为零,证明此固位螺丝
确实是接地的。
如果冷水管不容易接近, 连接60到100瓦的检修灯(不是霓虹灯)在插座的高电位侧与固位螺丝之间。如果有必要
的话,两个插槽都试试,以确定哪边是高电位侧,。如果螺丝在接地电位上,那么在正常的情况下灯是能被点亮的
(如图B所示。
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
7
SELF DIAGNOSIS FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED will automatically begin to flash.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the STANDBY LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these
problems occur.
DIAGNOSTIC TEST INDICATORS
When an error occurs, the STANDBY LED will flash a set number of times to
indicate the possible cause of the problem.
If there is more than one error, the LED will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen.
If the screen displays a “0”, no error has occurred .
STBY LED
Flash time
2
3
DC_ALERT1
AUDIO_PROT
BALANCER_ERR
4
5
DISPLAY OF STANDBY LED FLASH COUNT
0.5
0.5
Service menu Item name
(Screen Display)
MAIN_POWER
Diagnostic Item Description
Main Power Over Voltage Protection
DC_ALERT
Audio Abnorm al Detection
Balancer Error
TCON_ERR
Detect TCON_RDY
PANEL_ID__NVM_ERR
Panel ID NVM Error
6
7
BACKLIGHT_ERR
TEMP_ERR
Back Light Error (Panel Inverter)
Therm al Error
8
-
Not us ed
9
-
Not us ed
10
11
-
Not us ed
Not us ed
12
-
Not us ed
3
SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurrences of failure for
confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
*
Info
Channel 5
Volume
TV POWER
* : Note that this differs from entering the service mode (volume +)
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
8
自诊断功能
在本手册本单元中包含了自我诊断功能。如果出现故障,待机指示灯会自动闪烁。
LED指示灯闪烁次数指示了问题的来源。
LED指示灯闪烁次数所指示的问题见使用说明书使用须知与参考部分。
如果故障状态不能重现,可用遥控器回顾内存里的故障发生资料来查看以往故障及故障频率。
诊断测试指标
当故障出现时,待机LED指示灯将按照一定的次数闪烁来表示可能的故障原因。
待机指示灯闪
如果故障超过一个以上, LED将先识别故障类别。
烁次数
诊断项目的所有结果都会显示在界面上。
2
如果界面显示为“0”的话,则无故障出现。
维修菜单名称
(显示界面)
MAIN_POWER
DC_ALERT1
3
AUDIO_PROT
待机指示灯闪烁计数显示
BALANCER_ERR
4
TCON_ERR
5
0.5
0.5
PANEL_ID__NVM_ERR
自诊断描述
主电源过电压保护
直流电报警
声音异常检测
平衡器故障
检测T-CON就位信号
液晶屏上的非易失性存储器中参数错误
背光灯报错(高压板)
6
BACKLIGHT_ERR
7
TEMP_ERR
8
-
无此项
9
-
无此项
10
-
无此项
11
-
无此项
12
-
无此项
3
温度报错
自诊断界面显示
例如“有时关机”或“屏幕有时不显示”,这些无法确定的故障状态,可医用如下的方法进入自增段的方法来检测判断故障
[跳出测试界面]
在待机的状态下,按照如下的顺序快速连续的按遥控器上的按键:
*
屏显
频道 5
音 量
-
电视电源
* : 请注意这里需要区别于进入维修模式(音量 +)
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
8
SELF DIAGNOSIS FUNCTION
[SELF DIAGNOSTIC SCREEN DISPLAY]
Item name
STBY LED flash time
SELF CHECK
BACK
002 MAIN_POWER
003 DC_ALERT1 003 AUDIO_PROT 004 BALANCER_ERR 005 TCON_ERR 005 PANEL_ID_NVM_ERR 006 BACKLIGHT_ERR 007 TEMP_ERR <<
000
000
000
000
000
000
000
000
Error count
12345‐67891‐23456
[Home] Exit
Panel operation time by hour
Boot count
Total operation time by hour
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen.
After you have completed the repairs, clear the result display to “0”.
Clearing the Self Check Diagnostic List
1. Error history and Error count :
2. Panel operation time :
Press the Channel 8 => Channel 0 .
Press the Channel 7 => Channel 0 .
Exiting the Self-diagnostic screen
To exit the Self Diagnostic screen, turn off the power to the TV by pressing the POWER button on the remote or the POWER button on the TV.
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
9
自诊断功能
[自诊断显示屏显]
项目名称
LED待机指示灯闪烁次数
SELF CHECK
BACK
002 MAIN_POWER
003 DC_ALERT1
003 AUDIO_PROT
004 BALANCER_ERR
005 TCON_ERR
005 PANEL_ID_NVM_ERR
006 BACKLIGHT_ERR
007 TEMP_ERR
<<
000
000
000
000
000
000
000
000
故障次数
12345‐67891‐23456
[Home] Exit
液晶屏运行小时数
启动次数
总运行小时数
因为显示在屏幕上的诊断结果不会自动清除,并始终停留在自我诊断屏幕。
当你完成修理时,把显示结果清零。
清除自我诊断表
1. 故障历史记录和数量:
2. 液晶屏运行时间:
按按键8 => 按键 0 .
按按键7 => 按键 0 .
退出自诊断屏显
退出自诊断屏显,按下遥控器上的POWER键或者是电视机上的POWER开关来关掉电视机。
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
9
SERVICE POSITION
As for this model, the stands are attached the rear cover side.
Therefore assemble the stand assy to the main unit according to the following procedure when performing adjustment and operation check after the part replacement.
<32 inch>
1. Disassemble of the Bottom frame from the Rear cover (One screw)
2. Assemble of the Bottom frame to LCD panel (Three screws)
3. Assemble of the Stand to main unit (Three screws)
1
2
3
Note: Use screws which were fixing the rear cover. (+PSW M4x10)
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
10
SERVICE POSITION
<40 inch>
1. Disassemble of the Bottom frame from the Rear cover (One screw)
2. Assemble of the Bottom frame to LCD panel (Three screws)
3. Assemble of the Stand to main unit (Three screws)
1
2
3
Note: Use screws which were fixing the rear cover. (+PSW M4x10)
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
11
SERVICE POSITION
<46 inch>
1. Disassemble of the Bottom frame from the Rear cover (Two screws)
3. Assemble of the Stand to main unit (Three screws)
2. Assemble of the Bottom frame to LCD panel (Five screws)
Note: Use screws which were fixing the rear cover. (+PSW M4x10)
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
1
2
3
12
SEC 1. DISASSEMBLY AND PARTS LIST
• Items with no part number and no description are not stocked because they are seldom required for roution service.
• The construction parts of an assembled part are indicated with a collation number in the remark colum.
• Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
Note: When removing the rear cover, to prevent damaging the rear cover, please refer to “APPENDIX-1”.
Note: Bezel and LCD panel have points installing with double sided tape.
About the procedure of those disassembly and assembly methods, please refer to “APPENDIX-2”.
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
13
DISASSEMBLY AND PARTS LIST
1-1. KLV-32BX350
1-1-1. BASE STAND
REF. No. PART No.
1
2
3
DESCRIPTION
4-419-586-01
4-400-568-01
1-839-908-11
STAND, BASE(M)
COVER AC (APOW)
POWER SUPPLY CORD
2-580-592-01
SCREW, +PSW M3X8
2-580-608-11
SCREW, +PSW M5X16
MARK
1
1-1-2. AC COVER AND AC CORD
2
3
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
14
DISASSEMBLY AND PARTS LIST
1-1. KLV-32BX350
1-1-3. REAR COVER
REF. No. PART No.
4
4
5
6
7
8
9
DESCRIPTION
MARK
4-419-547-01
1-490-176-21
1-474-381-12
1-895-169-31
4-400-566-01
1-858-770-11
REAR COVER (32APOW)
SWITCH UNIT
G9(CH) STATIC CONVERTER (TV)
MOUNTED PWB A
BRACKET, SIDE (APOW CH)
SPEAKER 4X10
2-580-640-01
SCREW, +BVTP 4X16 TYPE2 IT-3
7-682-948-01
SCREW, +PSW 3X8
7-685-647-79
SCREW +BVTP 3X12 TYPE2 IT-3
4-159-298-01
SCREW, +PSW M4X10
1-1-4. G9 BOARD, A BOARD, SPEAKER AND SWITCH UNIT
6
7
8
5
9
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
15
DISASSEMBLY AND PARTS LIST
1-1. KLV-32BX350
1-1-5. H BOARD
REF. No.
10
11
10
11
12
13
14
15
16
17
18
19
PART No.
DESCRIPTION
1-910-103-77
1-910-103-73
1-895-170-11
1-910-103-75
1-910-103-74
4-417-048-01
4-419-544-01
1-910-103-76
1-811-602-11
1-910-105-27
CONNECTOR ASSY 4P SP
CONNECTOR ASSY 12P IR
MOUNTED PWB H
CONNECTOR ASSY 14P INV
CONNECTOR ASSY 3P MB-KEY
PANEL SUPPORT (E)
BEZEL (32APOW)
CONNECTOR ASSY 16P PS
PANEL, LCD (W32)
CONNECTOR ASSY FFC 32
2-580-640-01
SCREW, +BVTP 4X16 TYPE2 IT-3
MARK
12
1-1-6. PANEL SUPPORT, LCD PANEL AND BEZEL
15
17
13
18
19
14
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
16
16
DISASSEMBLY AND PARTS LIST
1-2. KLV-40BX450
1-2-1. BASE STAND
REF. No. PART No.
1
2
3
DESCRIPTION
4-419-587-01
4-400-568-01
1-839-908-11
STAND, BASE(ML)
COVER AC (APOW)
POWER SUPPLY CORD
2-580-592-01
SCREW, +PSW M3X8
2-580-608-11
SCREW, +PSW M5X16
MARK
1
1-2-2. AC COVER AND AC CORD
2
3
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
17
DISASSEMBLY AND PARTS LIST
1-2. KLV-40BX450
1-2-3. REAR COVER
REF. No. PART No.
4
4
5
6
7
8
9
DESCRIPTION
MARK
4-419-548-01
1-490-176-21
1-895-171-11
1-895-169-21
4-400-566-01
1-858-770-11
REAR COVER (40APOW)
SWITCH UNIT
MOUNTED PWB W40
MOUNTED PWB A
BRACKET, SIDE (APOW CH)
SPEAKER 4X10
2-580-640-01
SCREW, +BVTP 4X16 TYPE2 IT-3
7-682-948-01
SCREW, +PSW 3X8
7-685-647-79
SCREW +BVTP 3X12 TYPE2 IT-3
4-159-298-01
SCREW, +PSW M4X10
1-2-4. W40 BOARD, A BOARD, SPEAKER AND SWITCH UNIT
7
6
8
5
9
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
18
DISASSEMBLY AND PARTS LIST
1-2. KLV-40BX450
1-2-5. H BOARD
REF. No.
10
10
11
12
13
14
15
16
17
18
PART No.
DESCRIPTION
1-910-103-73
1-895-170-11
4-417-086-01
1-910-103-78
1-910-103-80
4-419-545-01
1-811-603-11
1-910-103-79
1-910-105-26
CONNECTOR ASSY 12P IR
MOUNTED PWB H
PANEL SUPPORT (F)
CONNECTOR ASSY 3P MB-KEY
CONNECTOR ASSY 4P SP
BEZEL (40APOW)
PANEL, LCD (W40)
CONNECTOR ASSY 16P PS
CONNECTOR ASSY FFC 40
2-580-640-01
SCREW, +BVTP 4X16 TYPE2 IT-3
MARK
11
1-2-6. PANEL SUPPORT, LCD PANEL AND BEZEL
12
16
17
18
13
14
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
15
19
DISASSEMBLY AND PARTS LIST
1-3. KLV-46BX450
1-3-1. BASE STAND
REF. No. PART No.
1
2
3
4
DESCRIPTION
4-419-588-01
4-400-568-01
1-839-908-11
4-419-549-01
STAND, BASE(L)
COVER AC (APOW)
POWER SUPPLY CORD
REAR COVER (46APOW)
2-580-592-01
SCREW, +PSW M3X8
2-580-608-11
SCREW, +PSW M5X16
2-580-640-01
SCREW, +BVTP 4X16 TYPE2 IT-3
4-159-298-01
SCREW, +PSW M4X10
7-685-647-79
SCREW +BVTP 3X12 TYPE2 IT-3
MARK
1
1-3-2. AC COVER, AC CORD AND REAR COVER
4
2
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
3
20
DISASSEMBLY AND PARTS LIST
1-3. KLV-46BX450
1-3-3. G11 BOARD, A BOARD, SPEAKER AND SWITCH UNIT
REF. No. PART No.
5
6
7
8
9
DESCRIPTION
1-490-176-21
1-474-382-12
1-895-169-11
4-400-566-01
1-858-770-11
SWITCH UNIT
G11 STATIC CONVERTER (TV)
MOUNTED PWB A
BRACKET, SIDE (APOW CH)
SPEAKER 4X10
7-682-948-01
SCREW, +PSW 3X8
7-685-647-79
SCREW +BVTP 3X12 TYPE2 IT-3
MARK
7
6
8
5
9
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
21
DISASSEMBLY AND PARTS LIST
1-3. KLV-46BX450
1-3-4. PANEL SUPPORT AND CONNECTOR ASSY
11
REF. No.
11
14
10
15
PART No.
DESCRIPTION
10
11
12
13
14
15
16
17
18
19
1-910-103-82
4-417-048-01
1-910-103-81
1-910-105-25
1-811-575-11
1-910-103-83
4-419-546-01
1-910-103-84
1-895-170-11
1-910-103-73
CONNECTOR ASSY 14P INV
PANEL SUPPORT (E)
CONNECTOR ASSY 3P MB-KEY
CONNECTOR ASSY FFC 46
LCD PANEL (S46ESPW)
CONNECTOR ASSY 16P PS
BEZEL (46APOW)
CONNECTOR ASSY 4P SP
MOUNTED PWB H
CONNECTOR ASSY 12P IR
MARK
20
4-423-579-01
INSULATION SHEET G
7-682-948-01
SCREW, +PSW 3X8
2-580-640-01
SCREW, +BVTP 4X16 TYPE2 IT-3
20
12
13
1-3-5. MB BRACKET, H BOARD AND BEZEL
MB Bracket L
MB Bracket R
19
16
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
17
18
22
DISASSEMBLY AND PARTS LIST
1-4. OTHER PART
1-4-1. MISCELLANEOUS
PART No.
DESCRIPTION
4-414-471-01
LABEL, REAR TERMINAL
1-489-995-11
REMOTE COMMANDER (RM-SA022)
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
MARK
23
SEC 2. ADJUSTMENT
HOW TO ENTERING SERVICE MODE
1) Turn on the main power switch to place this set in standby mode.
2) Press the buttons on the remote commander as follows, and entering service mode.
Info
Channel 5
Volume
TV POWER
3) Service mode display.
Service Mode
Status Information
Self diagnosis history
Panel Selection NO_SIGNAL_MUTE TUNING SYSTEM
LVDS Spectrum (%o)
Low of HPD
SERIAL NUMBER EDID
MODEL NAME EDID
Load Service Table
<[
<[
<[
<[
<[
<[
>>
>>
10 W_SE32 Off
AUTO
30
5
002EJ0S
KDL‐32BX350
Off
]>
]>
]>
]>
]>
]>
[</>]Set[Home]Exit
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
24
ADJUSTMENT
4) How to use the remote commander.
Function
The flow of control
Service mode on
<Info><5><Vol Up><Power>
Service mode off
<Other> / <Power off + on>
Adjustment Item up / down
/
Data Value up / down
/
5) After entering service mode, then turn off the power switch.
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
25
SEC 3. DIAGRAMS
3-1. BLOCK DIAGRAM
3-1-1. BLOCK
3 kinds of connectors
32” WXGA (LVDS)
40” FHD (Mini LVDS)
46” FHD (LVDS)
MT5306
Tuner
LVDS/miniLVDS/TCON/OD
JPEG/MP2/MP4/
DivX/VC-1
RM/AVS Decoders
EP1
VP6/VP8 Decoders
Component/
Video
NTSC/
PAL/
SECAM
ATD
TV
Decoder
Video
ADC×4
Panel
Deinterlace
PIP
Vplane
scaler
Video
Input
2D
Graphic
OSD Scaler
Audio
DSP
Audio I/F
Audio DAC
Post Processing
HDMI Rx
PC
Audio
Demod
PC/HDMI
Audio
USB
8W
8W
Audio
Input
Audio
DAC
DDR2
DDR3
Controller
ARM11
HDMI
STA381
BWS
SPDIF
In
L2 Cashe
JTAG
IrDA
I2C
USB2.0
PWM
PCR
RTC
Smart Card
UART
SDIO
Watchdog
SerialFlash
ServoADC
T8032
NAND
XTAL
CKGEN
DDR3
1GB
Line out /
Side HP
NAND
512MB
H Board
Tact Key
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
26
DIAGRAMS
3-2. CONNECTOR DIAGRAM
3-2-1. KLV-32BX350
Panel
T-Con Board
CN2001
CN6401
CN6402
CN4903
CN1003
Inverter
G9
Power Board
CN8002
CN1004
Main Board
CN9101
IR Board
Key Pad
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
27
DIAGRAMS
3-2-2. KLV-40BX450
Panel
Control Board
CN2
CN2001
CN4904
CN1003
DPS166DP
LIPS
CN8002
CN1004
Main Board
CN9101
IR Board
Key Pad
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
28
DIAGRAMS
3-2-3. KLV-46BX450
Panel
T-Con Board
CN2001
CN6401
CN6402
CN4902
CN1003
Inverter
APS319
Power Board
CN8002
CN1004
Main Board
CN9101
IR Board
Key Pad
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
29
DIAGRAMS
3-3. CIRCUIT BOARDS LOCATION
KLV-40BX450
KLV-32BX350
W40 Board
G9 Board
A Board
A Board
Switch Unit
Switch Unit
H Board
H Board
KLV-46BX450
G11 Board
A Board
Switch Unit
H Board
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
30
END
9-888-459-02
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
Sony Corporation
Home Entertainment
Business Group
English
2012BL08-Data
Made in Japan
© 2012. 02
31
APPENDIX-1
PROCEDURE TO REMOVAL OF REAR COVER
1. Remove all screws on Rear Cover and AC Cover.
2. Open Rear Cover in order as below.
1
2
32 inch
Disassemble the AC cover
3
Pull the AC cord connector
4
40 inch
46 inch
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
Hold the panel from the hole of the AC cover,
and have the center of the rear cover bottom.
Lift rear cover in the direction of the arrow.
32
附录-1
拆除后盖步骤
1. 关闭电源并拆卸螺丝。
2. 按照如下步骤打开后盖。
2
1
32 寸
拆下电源盖板
40 寸
46 寸
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
3
拔下电源线连接头
4
从电源盖板的孔洞按住液晶屏,
同时抓住后盖底部的中间部位。
朝着箭头的方向抬起后盖.
32
APPENDIX-2
1. PROCEDURE TO REMOVE LCD PANEL FROM BEZEL ASSY
Peel off double sided tapes between bezel assembly and LCD panel when exchanging LCD panel, etc, allow below instruction.
1.Put off “Bracket, Panel”
2.Peel off double sided tape
(1) Disassemble 2 screws
(2) Unplug the IR wire
A
B
Use tool to loosen the hook as “A”, Pull out
the hook as “B”.
(3) Remove the panel from the bezel
Lift the panel up to disassemble the bezel.
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
33
附录-2
1. 从面板移除液晶屏的步骤
当要更换液晶屏时,撕下粘在边框与液晶屏之间的胶带, 等等 ,请遵循如下指导。
1.分离 “支架与液晶屏”
2.剥离两边的胶带
(1) 拆卸2个螺丝
(2) 拔掉红外线接收板的连接线
A
B
使用工具松动锁扣“A”, 并移除“B”。
(3) 面板上移动液晶屏
从边框上拆去液晶屏。
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
33
APPENDIX-2
2. EXCHENGE DOUBLE SIDED TAPES
Because double sided tape’s strength weaken when tapes once peeled off, peel off all tapes from bezel assembly, and stick new ones (P/N: 4-281-014-01).
1.Peel off double sided tapes from Panel.
(Possibly remain on Bezel side)
2.Stick double sided tapes
Peel off separate papers before panel puts on.
32”
1position
230 x 12mm, t=0.4
46”
1position
230 x 12mm, t=0.4
40”
2position
230 x 12mm, t=0.4
1position
230 x 12mm, t=0.4
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
34
附件-2
2. 更换双面胶带
由于,当胶被剥离过一次后双面胶的粘性就会减弱;剥掉面板组件上所有的胶带, 并且附上新的(P/N: 4-281-014-01)。
1. 从面板组件上撕下双面胶带。
(胶带可能还黏在面框边上)
2.液晶屏装上前清理干净双面胶带纸。
32”
位置1
230 x 12mm, t=0.4
46”
位置1
230 x 12mm, t=0.4
40”
位置2
230 x 12mm, t=0.4
位置1
230 x 12mm, t=0.4
KLV-32BX350,40/46BX450(CH)
5BEE7C12F6303DC82CF88F94C89335DE228C2E33B63EF4C97C76C4AE6FD7BFACDFCEC4DBFE63737C
34