INSTALLATION AND OPERATION MANUAL - Garland

INSTALLATION AND
OPERATION MANUAL
SUNFIRE GAS RESTAURANT
RANGE MODELS
SX-6-26A AND SX-6A
FOR YOUR SAFETY:
DO NOT STORE OR USE GASOLINE
OR OTHER FLAMMABLE VAPORS OR
LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER
APPLIANCE
WARNING:
IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR MAINTENANCE
CAN CAUSE PROPERTY DAMAGE, INJURY,
OR DEATH. READ THE INSTALLATION,
OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY
BEFORE INSTALLING OR
SERVICING THIS EQUIPMENT
PLEASE READ ALL SECTIONS OF THIS MANUAL
AND RETAIN FOR FUTURE REFERENCE .
THIS PRODUCT HAS BEEN CERTIFIED AS
COMMERCIAL COOKING EQUIPMENT AND
MUST BE INSTALLED BY PROFESSIONAL
PERSONNEL AS SPECIFIED .
For Your Safety:
Post in a prominent location, instructions to be
followed in the event the user smells gas . This
information shall be obtained by consulting
your local gas supplier .
Users are cautioned that maintenance and repairs must be performed by a Garland authorized service agent
using genuine Garland replacement parts . Garland will have no obligation with respect to any product that has been
improperly installed, adjusted, operated or not maintained in accordance with national and local codes or installation
instructions provided with the product, or any product that has its serial number defaced, obliterated or removed,
or which has been modified or repaired using unauthorized parts or by unauthorized service agents .
For a list of authorized service agents, please refer to the Garland web site at http://www .garland-group .com .
The information contained herein, (including design and parts specifications), may be superseded and is subject
to change without notice .
GARLAND COMMERCIAL INDUSTRIES
185 East South Street
Freeland, Pennsylvania 18224
Phone: (570) 66-1000
Fax: (570) 66-90
Part##4515558
451558 (02/29/08)
Part
(02/29/08)
GARLAND COMMERCIAL RANGES, LTD .
1177 Kamato Road, Mississauga, Ontario L4W 1X4
CANADA
Phone: 905-624-0260
Fax: 905-624-5669
Enodis UK LTD .
Swallowfield Way, Hayes, Middlesex UB 1DQ ENGLAND
Telephone: 081-561-04
Fax: 081-848-0041
© 2005 Garland Commercial Industries,
Inc .1
Page
Page Part # 4515558 (02/29/08)
TABLE OF CONTENTS
DIMENSIONS AND SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Siting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Appliances Equipped With Casters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Appliances Equipped With Legs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing The Backguard Or Shelf. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Ventilation Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Statutory Regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Gas Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TESTING & ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pilot Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Burner Gas/Air Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Open Top Burners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Standard Ovens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
MAINTENANCE & CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Exterior Finish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Oven Interior (Porcelain Enamel). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Open Top Burners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cast Iron Top Grates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Part # 4515558 (02/29/08)
Page DIMENSIONS AND SPECIFICATIONS
Total
BTU/Hr
Shipping Information
Lbs.
Kg
Cube
Six Open Burners w/26" Oven
162,000
446
202
38.0
Six Open Burners w/open storage
132,000
346
157
38.0
Mode
Number
SX-6-26A
SX-6A
Width
Description
36"
33-1/8"
(914mm) (841mm)
3"
(76mm)
Height
Depth
Oven Interior
Combustible Wall Clearance
w/Legs
w/o Legs
Height
Depth
Width
Sides
Rear
38-1/2"
(978mm)
32-1/2"
(826mm)
13-1/2"
(343mm)
22"
(559mm)
26-1/4"
(667mm)
9"
(229mm)
6"
(152mm)
Burner Ratings (BTU/Hr)
3/4" NPT
REAR GAS
INLET
Open
Oven
22,000
30,000
Entry Clearances
3-7/16"
(87mm)
Crated
Uncrated
46" (1168mm)
34" (864mm)
These appliances are intended for commercial use by
professionally trained personnel.
It is the responsibility of the installer to ensure that installation
complies with national and local codes.
36"
(914mm)
11-1/2"
(292mm)
33-1/8"
(841mm)
17-3/8"
(441mm)
13-13/16"
(351mm)
3/4" NPT
REAR GAS
INLET
53-5/32"
(1350mm)
32-1/2"
(826mm)
6" (152mm)
Page OVEN INTERIOR
HxWxD
13-1/2" x 26-1/4" x 22"
(343mm x 667mm x
559mm)
26"
(660mm)
29"
(737mm)
Part # 4515558 (02/29/08)
DIMENSIONS AND SPECIFICATIONS, Continued
GAS PRESSURES
Minimum Supply Gas Pressure
Operating Pressure
Natural Gas:
1.12 kPa.
Natural Gas:
1.0 kPa.
Propane:
2.75 kPa.
Propane:
2.75 kPa.
NOMINAL GAS CONSUMPTION AND INJECTOR SIZE
Natural Gas
Propane Gas
INJ. DIA.
mm
MJ/H
Gas Pressure (kPa)
INJ. DIA.
mm
MJ/H
Gas Pressure (kPa)
FULL SIZE OVEN
2.5
29.5
1.0
1.55
31.6
2.75
OPEN TOP
2.08
21.4
1.0
1.32
21.4
2.75
INTRODUCTION
1. Check crate for possible damage sustained during transit.
Carefully remove unit from crate and again check for
damage. Any damage to the appliance must be reported
to the carrier immediately.
4. The type of gas and supply pressure that the equipment
was set-up for at the factory is noted on the data plate
and on the packaging. This type of gas supply must be
used.
2. The wires for retaining the burners and other packing
material must be removed from units. Any protective
material covering stainless steel parts must also be
removed.
5. Do not remove permanently affixed labels, warnings or
data plates from the appliance, for this may invalidate the
manufacturer’s warranty.
3. All equipment is shipped from the factory with legs
fitted, unless otherwise specified. Where the range is to
be mounted on a dais or cove base, it is shipped without
legs. Legs must be fitted to the oven when it is installed
on a combustible floor.
Part # 4515558 (02/29/08)
Page INSTALLATION
Clearances
Construction
Sides
Rear
Combustible
9” (230 mm)
6” (152 mm)
Non-combustible
0 mm
0 mm
3. Securely fasten the support brackets to the burner box
sides with (4) #14 x 5/8 Hex washer head, type B tapping
screws. (Hardware package is supplied).
Upright
Siting
The floor on which the appliance is to be sited must be
capable of adequately supporting the weight of the
appliance and any ancillary equipment.
Burner Box
Side
Units with ovens must be fitted with legs if installed on a
combustible floor.
#14 x 5/8"
Type "B"
Hex Head
Tapping Screw
4 Req'd
Appliances Equipped With Casters
1. The front casters on the appliance are equipped with
brakes to limit the movement of the appliance without
placing any strain on the connector or quick-disconnect
device or its associated piping.
2. Please be aware; required restraint is attached to a
bracket (which is located on the rear caster closest to the
gas connection), and if disconnection of the restraint
is necessary; be sure to reconnect the device after the
appliance has been returned to its original position.
NOTE: The installation shall be made with a connector that
complies with the current applicable A.G.A Standards.
Appliances Equipped With Legs
1. Raise the front of the appliance and block. Do not lay the
appliance on its back.
2. Position leg insert in leg retainer opening and tap upward
until the insert seats at the collar flange.
3. Repeat leg insert installation for the other legs and adjust
all four legs to the same height.
Ventilation Air
The following notes are intended to give general guidance.
For detailed recommendations, refer to the applicable
code(s) in the country of destination.
Proper ventilation is highly essential for optimum
performance. The ideal method of ventilating open-top
equipment is the use of a properly designed canopy that
should extend 152mm, beyond all sides of the appliance(s)
and 1981mm above the floor.
A strong exhaust will create a vacuum in the room. For an
exhaust vent to work properly, replacement air must enter
the room. The amount of air that enters must be equal to the
amount exhausted.
4. Legs can be further adjusted to level the appliance and to
compensate for uneven flooring.
All gas burners and pilots need sufficient air to operate. Large
objects should not be placed in front of the appliance(s) that
would obstruct the flow of air into the front.
Installing The Backguard Or Shelf
Statutory Regulations
1. Rear of range must be easily accessible.
The installation of this appliance must be carried out by
a competent person and in accordance with the relevant
regulations, codes of practice and the related publications of
the country and destination.
2. Place the backguard, high shelf, salamander, or
cheesemelter on the rear of the range, slipping the
support brackets into the openings in the burner box
sides.
Page Part # 4515558 (02/29/08)
INSTALLATION Continued
This appliance must be installed in accordance with the
manufacturer’s instructions, local gas fitting regulations and
requirements of the A.G.A. 601 Installation Code. All burner
adjustments and settings should be made by a qualified gas
technician.
Gas Connection
The local gas authority should be consulted at the
installation planning stage in order to establish the
availability of an adequate supply of gas and to ensure
that the meter is adequate for the required flow rate. The
pipe work from the meter to the appliances must be of an
appropriate size.
All fixed (non-mobile) appliances MUST be fitted with a
manual gas-cock upstream of the appliance to provide a
means of isolation for servicing or cleaning purposes. A
union or similar means of disconnection must be provided
between the gas-cock and the appliance.
A manually operable valve must be fitted to the gas supply
to the kitchen to enable it to be isolated in an emergency.
Wherever practical, this shall be located either outside the
kitchen or near to an exit in a readily accessible position.
Where it is not practical to do this, an automatic isolation
valve system shall be fitted which can be operated from a
readily accessible position near to the exit.
At locations where the manual isolation valve is fitted or
the automatic system can be reset a notice MUST be fitted
stating:
“ALL DOWNSTREAM BURNER AND PILOT VALVES MUST
BE TURNED OFF PRIOR TO ATTEMPTING TO RESTORE THE
SUPPLY. AFTER EXTENDED SHUT OFF, PURGE BEFORE
RESTORING GAS.”
Before assembly and connection check gas supply.
A. The type of gas for which the unit is equipped is stamped
on the data plate located behind the lower front panel.
Connect a unit stamped “NAT” only to natural gas;
connect one stamped “PRO” only to propane gas.
B. If it is a new installation have the gas authorities check
meter size and piping to assure that the unit is supplied
with necessary amount of gas pressure required to
operate the unit.
C. If it is additional or replacement equipment have the gas
authorities check pressure to make certain that existing
meter and piping will supply fuel to the unit with no
more than 0.15 kPa pressure drop.
NOTE: When checking gas pressure, be sure that all other
equipment on the same gas line is on.
The appliance and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of that system pressures in excess of
3.45kPa.
Adequate clearance must be provided for servicing and
proper operation.
THIS APPLIANCE IS NOT RECOMMENDED FOR RESIDENTIAL
INSTALLATION.
TESTING & ADJUSTMENT
Testing
All fittings and pipe connections must be tested for
leaks. Use approved gas leak detectors, soap solution or
equivalent, checking over and around all the fittings and
pipe connections. DO NOT USE A FLAME! Accessibility to
all gas lines and fittings require that valve panel(s), lower
front panel(s), and/or oven rack(s) be removed. All parts
removed, (including fasteners), should be stored safely for
re-installation.
Part # 4515558 (02/29/08)
1 Be sure that all valves and thermostats are in the “OFF”
position.
2. Turn on the main gas supply valve. Light all top section
pilots.
3. Leak test all valves and fittings as described at the
beginning of this section. Correct any leaks as required
and recheck.
Page TESTING & ADJUSTMENT Continued
4. Check pilot flame on installation. If pilot adjustment is
required at any time, please ensure the pilot adjustment
screw is sealed and there are no leaks.
5. Light the oven pilot.
1. Check operation and adjust as below to provide a sharp
blue flame at full rate.
2. On the burner (open top and oven burners) locate the air
shutter.
6. Set the thermostat to 260°C. Leak test all valves and
fittings as described at the beginning of this section.
Correct any leaks as required and recheck.
3. Loosen the lock-nut so that the air shutter turns freely.
7. Shut off all valves and set thermostat dials to “OFF” or
lowest position.
5. Rotate the air shutter to obtain stable, sharp inner blue
cones. (Slight yellow tips on oven).
All units are tested and adjusted at the factory, however,
burners and pilots should be checked upon installation and
adjusted if necessary.
If the burner flames are sharp but lift of the burner ports,
reduce the amount of primary air by closing the air shutter. If
the burner flames are lazy and yellow in appearance, increase
the primary air by opening shutter. If poor performance
persists check for proper gas pressure.
CAUTION: Gas will flow to the top section burners even if
top section pilots are not lit. Gas will not be interrupted. It
is the responsibility of the operator to confirm the proper
ignition of each burner as it is turned on. Should ignition
fail to occur 5 seconds after turning a burner on, turn the
burner off, wait 5 minutes, and try again.
Adjustments
The top and oven orifices are fixed and cannot be adjusted.
Proper rate is attained if the gas supply pressure is adequate.
Pressure may be checked by 1/8” N.P.T. manifold pressure tap.
A properly adjusted air shutter will provide for a distinct blue
flame over the entire port area of the burners when at full
rate.
4. Reinstall burner. Turn on gas and ignite burner.
Injector Location
Fixing Screw
Required Length
of Opening
Aeration
Shutter
OVEN BURNER SHUTTER
INJECTOR
LOCATION
Pilot Adjustment
All pilot adjustment valves are mounted on the range to
manifold. When properly adjusted it should neither lift of the
burner nor should it show a yellow tip.
OPENING
Burner Gas/Air Adjustments
Variations in field conditions or rough handling of the
equipment in transit may indicate the need for adjustment of
primary air to the burners.
Page SKSHUT
Part # 4515558 (02/29/08)
OPERATION
Open Top Burners
Standard Ovens
Lighting:
Lighting:
1. Open 1/4 turn pilot isolation valves.
1. Remove oven bottom(s).
2. Light pilots.
2. Depress and hold the red reset button, located on the
safety valve behind the kick panel below the oven door,
while lighting the oven pilot. Continue to hold the reset
button for at least 60 seconds after the pilot is lit. Release
the button. If the pilot does not stay lit, wait five minutes,
then repeat the procedure.
3. Turn valve completely on. Burner flame should be 1/2
inch (13mm), stable blue flame, and should impinge on
the bottom of a pot placed on the ring grate.
Shut-Down:
1. Turn all valves to the “OFF” position.
2. If the unit is to be shut down for an extended period of
time, close the pilot isolation valves.
CAUTION: Should burner ignition fail within 5 seconds,
turn the burner valve off and repeat steps 1 through 5. If
ignition continues to fail, consult your factory authorized
service agency.
Shut-Down:
1. Turn all valves and thermostats to the “OFF” position, or
lowest setting.
2. If the range is to be shut down for an extended period of
time, close the in-line gas valve.
Re-lighting:
1. Turn all gas valves off.
2. Wait five minutes.
3. Follow procedure under “Lighting” at left.
Part # 4515558 (02/29/08)
Page MAINTENANCE & CLEANING
Exterior Finish
Oven Interior (Porcelain Enamel)
Establish a regular cleaning schedule. Any spills should be
wiped off immediately.
NOTE: Disconnect line cord (if applicable) from power
supply before cleaning or servicing.
The oven should be permitted to cool down before cleaning
exterior surfaces.
1. Before cleaning oven interior, remove all oven racks and
guides. Oven racks and guides can be cleaned with a mild
soap and warm water or run through a dishwasher.
1. Wipe exposed cleanable surface when cool with a mild
detergent and hot water. Stubborn residue spots may be
removed with a lightweight non-metallic scouring pad.
Dry thoroughly with a clean cloth.
2. The porcelain interior can be cleaned with oven cleaners
such as “Easy-Off” or “Dow Oven Cleaner”. Follow product
manufacturer’s instructions for proper use.
2. Stainless steel should be cleaned using a mild detergent,
a soft cloth and hot water. If necessary to use a nonmetallic scouring pad, always rub in the direction of the
grain in the metal to prevent scratching. Use a water
based stainless cleaner if you want a high shine.
Open Top Burners
Stainless Steel
1. The most common problem with open burner range is
spillage. Once the burner ports are partially plugged with
food, the air-to-gas mixture is disturbed and results in an
inefficient burner.
For routine cleaning just wash with hot water and detergent
solution. Wash just a small area at a time or the water will
evaporate leaving the chemicals behind causing streaking.
Rinse the washed area with a clean sponge dipped in a
sanitizing solution and wipe dry with soft clean cloth before
it can dry.
Use a paste (of water and a mild scouring powder) if you
have to, but never rub against the grain. All stainless steel has
been polished in one direction. Rub with the polish lines to
preserve the original finish. Then thoroughly rinse as before.
To prevent fingerprints there are several stainless steel
polishes on the market the leave and oily waxy film. Do not
use on surfaces that will be in contact with food.
Stainless steel may discolor if overheated. These stains can
usually be removed by vigorous rubbing with a scouring
powder paste.
Use only stainless steel, wood or plastic tools if necessary
to scrape off heavy deposits of grease and oil. Do not use
ordinary steel scrapers or knives, as particles of the iron may
become imbedded and rust. STEEL WOOL SHOULD NEVER BE
USED.
Cleaning of the range top burner is a simple procedure, if
done at regular intervals will prolong the life of the range
and ensure good flame characteristics.
2. Wipe any spills as they occur.
3. Grids and trays should be removed daily, washed, rinsed
and dried thoroughly.
4. Use a wire brush to clean the ports of the burners. Ignite
and check for clogged holes.
5. If any clogged holes are apparent, the burner should be
lifted out and brushed inside and out with a small Venturi
brush. Each port on the burner itself should be cleaned
with a properly sized wire or thumb drill. Wash with soap
and hot water if grease is observed on the burners. Dry
thoroughly.
6. Reinstall and check the flame pattern. Readjust the air
shutter if necessary.
7. If a yellow flame appears around the edges instead of
being uniformly blue, it is usually a sign of grease and dirt
in the throat of the burner. Remove and clean the burner
and readjust the air shutter.
Cast Iron Top Grates
Cast iron top grate(s) can be cleaned with mild soap and
warm water. For baked on material, a wire brush can be used.
Dry thoroughly and lightly coat with vegetable oil to help
prevent rust from forming.
Page 10
Part # 4515558 (02/29/08)
Part # 4515558 (02/29/08)
Page 11