Sun StorEdge™ PCI Single Fibre Channel Network Adapter

Sun StorEdge™
PCI Single Fibre Channel
Network Adapter
Installation Guide
Sun Microsystems, Inc.
901 San Antonio Road
Palo Alto, CA 94303
U.S.A. 650-960-1300
Part No. 806-7532-10
December 2000, Revision A
Send comments about this document to: docfeedback@sun.com
Copyright 2000 Sun Microsystems, Inc., 901 San Antonio Road • Palo Alto, CA 94303-4900 USA. All rights reserved.
This product or document is protected by copyright and distributed under licenses restricting its use, copying, distribution, and decompilation.
No part of this product or document may be reproduced in any form by any means without prior written authorization of Sun and its licensors,
if any. Third-party software, including font technology, is copyrighted and licensed from Sun suppliers.
Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered trademark in
the U.S. and other countries, exclusively licensed through X/Open Company, Ltd. For Netscape Communicator™, the following notice applies:
Copyright 1995 Netscape Communications Corporation. All rights reserved.
Sun, Sun Microsystems, the Sun logo, AnswerBook2, docs.sun.com, Sun Enterprise, SunVTS, StorEdge, and Solaris are trademarks, registered
trademarks, or service marks of Sun Microsystems, Inc. in the U.S. and other countries. All SPARC trademarks are used under license and are
trademarks or registered trademarks of SPARC International, Inc. in the U.S. and other countries. Products bearing SPARC trademarks are
based upon an architecture developed by Sun Microsystems, Inc.
The OPEN LOOK and Sun™ Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun acknowledges
the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry. Sun
holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun’s licensees who implement OPEN
LOOK GUIs and otherwise comply with Sun’s written license agreements.
RESTRICTED RIGHTS: Use, duplication, or disclosure by the U.S. Government is subject to restrictions of FAR 52.227-14(g)(2)(6/87) and
FAR 52.227-19(6/87), or DFAR 252.227-7015(b)(6/95) and DFAR 227.7202-3(a).
DOCUMENTATION IS PROVIDED “AS IS” AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.
Copyright 2000 Sun Microsystems, Inc., 901 San Antonio Road • Palo Alto, CA 94303-4900 Etats-Unis. Tous droits réservés.
Ce produit ou document est protégé par un copyright et distribué avec des licences qui en restreignent l’utilisation, la copie, la distribution, et la
décompilation. Aucune partie de ce produit ou document ne peut être reproduite sous aucune forme, par quelque moyen que ce soit, sans
l’autorisation préalable et écrite de Sun et de ses bailleurs de licence, s’il y en a. Le logiciel détenu par des tiers, et qui comprend la technologie
relative aux polices de caractères, est protégé par un copyright et licencié par des fournisseurs de Sun.
Des parties de ce produit pourront être dérivées des systèmes Berkeley BSD licenciés par l’Université de Californie. UNIX est une marque
déposée aux Etats-Unis et dans d’autres pays et licenciée exclusivement par X/Open Company, Ltd. La notice suivante est applicable à
Netscape Communicator™: Copyright 1995 Netscape Communications Corporation. Tous droits réservés.
Sun, Sun Microsystems, the Sun logo, AnswerBook2, docs.sun.com, Sun Enterprise, SunVTS, StorEdge, et Solaris sont des marques de fabrique
ou des marques déposées, ou marques de service, de Sun Microsystems, Inc. aux Etats-Unis et dans d’autres pays. Toutes les marques SPARC
sont utilisées sous licence et sont des marques de fabrique ou des marques déposées de SPARC International, Inc. aux Etats-Unis et dans
d’autres pays. Les produits portant les marques SPARC sont basés sur une architecture développée par Sun Microsystems, Inc.
L’interface d’utilisation graphique OPEN LOOK et Sun™ a été développée par Sun Microsystems, Inc. pour ses utilisateurs et licenciés. Sun
reconnaît les efforts de pionniers de Xerox pour la recherche et le développement du concept des interfaces d’utilisation visuelle ou graphique
pour l’industrie de l’informatique. Sun détient une licence non exclusive de Xerox sur l’interface d’utilisation graphique Xerox, cette licence
couvrant également les licenciés de Sun qui mettent en place l’interface d’utilisation graphique OPEN LOOK et qui en outre se conforment aux
licences écrites de Sun.
CETTE PUBLICATION EST FOURNIE "EN L’ETAT" ET AUCUNE GARANTIE, EXPRESSE OU IMPLICITE, N’EST ACCORDEE, Y COMPRIS
DES GARANTIES CONCERNANT LA VALEUR MARCHANDE, L’APTITUDE DE LA PUBLICATION A REPONDRE A UNE UTILISATION
PARTICULIERE, OU LE FAIT QU’ELLE NE SOIT PAS CONTREFAISANTE DE PRODUIT DE TIERS. CE DENI DE GARANTIE NE
S’APPLIQUERAIT PAS, DANS LA MESURE OU IL SERAIT TENU JURIDIQUEMENT NUL ET NON AVENU.
Please
Recycle
Regulatory Compliance Statements
Your Sun product is marked to indicate its compliance class:
•
•
•
•
Federal Communications Commission (FCC) — USA
Industry Canada Equipment Standard for Digital Equipment (ICES-003) - Canada
Voluntary Control Council for Interference (VCCI) — Japan
Bureau of Standards Metrology and Inspection (BSMI) — Taiwan
Please read the appropriate section that corresponds to the marking on your Sun product before attempting to install the
product.
FCC Class A Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is
not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required
to correct the interference at his own expense.
Shielded Cables: Connections between the workstation and peripherals must be made using shielded cables to comply with
FCC radio frequency emission limits. Networking connections can be made using unshielded twisted-pair (UTP) cables.
Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the
authority granted to the user by the FCC to operate this equipment.
FCC Class B Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Shielded Cables: Connections between the workstation and peripherals must be made using shielded cables in order to
maintain compliance with FCC radio frequency emission limits. Networking connections can be made using unshielded
twisted pair (UTP) cables.
Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the
authority granted to the user by the FCC to operate this equipment.
iii
ICES-003 Class A Notice - Avis NMB-003, Classe A
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
ICES-003 Class B Notice - Avis NMB-003, Classe B
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
iv
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • Decmber 2000
This page is intentionally left blank.
Regulatory Compliance Statements
v
This page is intentionally left blank.
vi
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • Decmber 2000
Safety Agency Compliance
Statements
Depending on the type of power switch your device has,
one of the following symbols may be used:
Off - Removes AC power from the system.
Read this section before beginning any procedure. The
following text provides safety precautions to follow when
installing a Sun Microsystems product.
Standby – The On/Standby switch is in the
standby position.
Safety Precautions
For your protection, observe the following safety
precautions when setting up your equipment:
■
■
■
Follow all cautions and instructions marked on the
equipment.
Ensure that the voltage and frequency of your power
source match the voltage and frequency inscribed on
the equipment’s electrical rating label.
Never push objects of any kind through openings in
the equipment. Dangerous voltages may be present.
Conductive foreign objects could produce a short
circuit that could cause fire, electric shock, or damage
to your equipment.
Symbols
The following symbols may appear in this book:
Caution – There is risk of personal injury and
equipment damage. Follow the instructions.
Caution – Hot surface. Avoid contact. Surfaces
are hot and may cause personal injury if
touched.
Modifications to Equipment
Do not make mechanical or electrical modifications to the
equipment. Sun Microsystems is not responsible for
regulatory compliance of a modified Sun product.
Placement of a Sun Product
Caution – Do not block or cover the openings
of your Sun product. Never place a Sun
product near a radiator or heat register.
Failure to follow these guidelines can cause
overheating and affect the reliability of your
Sun product.
Caution – The workplace-dependent noise
level defined in DIN 45 635 Part 1000 must be
70Db(A) or less.
SELV Compliance
Safety status of I/O connections comply to SELV
requirements.
Caution – Hazardous voltages are present. To
reduce the risk of electric shock and danger to
personal health, follow the instructions.
On – Applies AC power to the system.
vii
Power Cord Connection
Caution – Sun products are designed to work
with single-phase power systems having a
grounded neutral conductor. To reduce the
risk of electric shock, do not plug Sun
products into any other type of power system.
Contact your facilities manager or a qualified
electrician if you are not sure what type of
power is supplied to your building.
Caution – Not all power cords have the same
current ratings. Household extension cords do
not have overload protection and are not
meant for use with computer systems. Do not
use household extension cords with your Sun
product.
Caution – Your Sun product is shipped with a
grounding type (three-wire) power cord. To
reduce the risk of electric shock, always plug
the cord into a grounded power outlet.
The following caution applies only to devices with a
Standby power switch:
Caution – The power switch of this product
functions as a standby type device only. The
power cord serves as the primary disconnect
device for the system. Be sure to plug the
power cord into a grounded power outlet that
is nearby the system and is readily accessible.
Do not connect the power cord when the
power supply has been removed from the
system chassis.
Lithium Battery
Caution – On Sun CPU boards, there is a
lithium battery molded into the real-time
clock, SGS No. MK48T59Y, MK48TXXB-XX,
MK48T18-XXXPCZ, M48T59W-XXXPCZ, or
MK48T08. Batteries are not customer
replaceable parts. They may explode if
mishandled. Do not dispose of the battery in
fire. Do not disassemble it or attempt to
recharge it.
Battery Pack
Caution – There is a sealed lead acid battery
in Product Name units. Portable Energy
Products No. TLC02V50. There is danger of
explosion if the battery pack is mishandled or
incorrectly replaced. Replace only with the
same type of Sun Microsystems battery pack.
Do not disassemble it or attempt to recharge it
outside the system. Do not dispose of the
battery in fire. Dispose of the battery properly
in accordance with local regulations.
System Unit Cover
You must remove the cover of your Sun computer system
unit to add cards, memory, or internal storage devices. Be
sure to replace the top cover before powering on your
computer system.
Caution – Do not operate Sun products
without the top cover in place. Failure to take
this precaution may result in personal injury
and system damage.
Laser Compliance Notice
Sun products that use laser technology comply with Class 1
laser requirements.
viii
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser KLasse 1
Achtung – Gefahr von Verletzung und
Geräteschaden. Befolgen Sie die
Anweisungen.
Achtung – Hohe Temperatur. Nicht berühren,
da Verletzungsgefahr durch heiße Oberfläche
besteht.
CD-ROM
Caution – Use of controls, adjustments, or the
performance of procedures other than those
specified herein may result in hazardous
radiation exposure.
Achtung – Gefährliche Spannungen.
Anweisungen befolgen, um Stromschläge und
Verletzungen zu vermeiden.
Ein – Setzt das System unter Wechselstrom.
Einhaltung sicherheitsbehördlicher
Vorschriften
Auf dieser Seite werden Sicherheitsrichtlinien beschrieben,
die bei der Installation von Sun-Produkten zu beachten
sind.
Sicherheitsvorkehrungen
Treffen Sie zu Ihrem eigenen Schutz die folgenden
Sicherheitsvorkehrungen, wenn Sie Ihr Gerät installieren:
■
■
■
Beachten Sie alle auf den Geräten angebrachten
Warnhinweise und Anweisungen.
Vergewissern Sie sich, daß Spannung und Frequenz
Ihrer Stromquelle mit der Spannung und Frequenz
übereinstimmen, die auf dem Etikett mit den
elektrischen Nennwerten des Geräts angegeben sind.
Stecken Sie auf keinen Fall irgendwelche Gegenstände
in Öffnungen in den Geräten. Leitfähige Gegenstände
könnten aufgrund der möglicherweise vorliegenden
gefährlichen
Spannungen
einen
Kurzschluß
verursachen, der einen Brand, Stromschlag oder
Geräteschaden herbeiführen kann.
Je nach Netzschaltertyp an Ihrem Gerät kann eines der
folgenden Symbole benutzt werden:
Aus – Unterbricht die Wechselstromzufuhr
zum Gerät.
Wartezustand (Stand-by-Position) - Der Ein-/
Wartezustand-Schalter steht auf
Wartezustand. Änderungen an Sun-Geräten.
Nehmen Sie keine mechanischen oder elektrischen
Änderungen an den Geräten vor. Sun Microsystems,
übernimmt bei einem Sun-Produkt, das geändert wurde,
keine Verantwortung für die Einhaltung behördlicher
Vorschriften
Symbole
Die Symbole in diesem Handbuch haben folgende
Bedeutung:
Safety Agency Compliance Statements
ix
Aufstellung von Sun-Geräten
Achtung – Um den zuverlässigen Betrieb
Ihres Sun-Geräts zu gewährleisten und es vor
Überhitzung zu schützen, dürfen die
Öffnungen im Gerät nicht blockiert oder
verdeckt werden. Sun-Produkte sollten
niemals in der Nähe von Heizkörpern oder
Heizluftklappen aufgestellt werden.
Achtung – Der arbeitsplatzbezogene
Schalldruckpegel nach DIN 45 635 Teil 1000
beträgt 70Db(A) oder weniger.
Die folgende Warnung gilt nur für Geräte mit
Wartezustand-Netzschalter:
Achtung – Der Ein/Aus-Schalter dieses
Geräts schaltet nur auf Wartezustand (StandBy-Modus). Um die Stromzufuhr zum Gerät
vollständig zu unterbrechen, müssen Sie das
Netzkabel von der Steckdose abziehen.
Schließen Sie den Stecker des Netzkabels an
eine in der Nähe befindliche, frei zugängliche,
geerdete Netzsteckdose an. Schließen Sie das
Netzkabel nicht an, wenn das Netzteil aus der
Systemeinheit entfernt wurde.
Lithiumbatterie
Einhaltung der SELV-Richtlinien
Die Sicherung der I/O-Verbindungen entspricht den
Anforderungen der SELV-Spezifikation.
Anschluß des Netzkabels
Achtung – Sun-Produkte sind für den Betrieb
an Einphasen-Stromnetzen mit geerdetem
Nulleiter vorgesehen. Um die
Stromschlaggefahr zu reduzieren, schließen
Sie Sun-Produkte nicht an andere
Stromquellen an. Ihr Betriebsleiter oder ein
qualifizierter Elektriker kann Ihnen die Daten
zur Stromversorgung in Ihrem Gebäude
geben.
Achtung – Nicht alle Netzkabel haben die
gleichen Nennwerte. Herkömmliche, im
Haushalt verwendete Verlängerungskabel
besitzen keinen Überlastungsschutz und sind
daher für Computersysteme nicht geeignet.
Achtung – Ihr Sun-Gerät wird mit einem
dreiadrigen Netzkabel für geerdete
Netzsteckdosen geliefert. Um die Gefahr eines
Stromschlags zu reduzieren, schließen Sie das
Kabel nur an eine fachgerecht verlegte,
geerdete Steckdose an.
x
Achtung – CPU-Karten von Sun verfügen
über eine Echtzeituhr mit integrierter
Lithiumbatterie (Teile-Nr. MK48T59Y,
MK48TXXB-XX, MK48T18-XXXPCZ,
M48T59W-XXXPCZ, oder MK48T08). Diese
Batterie darf nur von einem qualifizierten
Servicetechniker ausgewechselt werden, da sie
bei falscher Handhabung explodieren kann.
Werfen Sie die Batterie nicht ins Feuer.
Versuchen Sie auf keinen Fall, die Batterie
auszubauen oder wiederaufzuladen.
Batterien
Achtung – Die Geräte Product Name
enthalten auslaufsichere Bleiakkumulatoren.
Produkt-Nr. TLC02V50 für portable
Stromversorgung. Werden bei der Behandlung
oder beim Austausch der Batterie Fehler
gemacht, besteht Explosionsgefahr. Batterie
nur gegen Batterien gleichen Typs von Sun
Microsystems austauschen. Nicht demontieren
und nicht versuchen, die Batterie außerhalb
des Geräts zu laden. Batterie nicht ins Feuer
werfen. Ordnungsgemäß entsprechend den
vor Ort geltenden Vorschriften entsorgen.
Gehäuseabdeckung
Sie müssen die obere Abdeckung Ihres Sun-Systems
entfernen, um interne Komponenten wie Karten,
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
Speicherchips oder Massenspeicher hinzuzufügen. Bringen
Sie die obere Gehäuseabdeckung wieder an, bevor Sie Ihr
System einschalten.
Achtung – Bei Betrieb des Systems ohne obere
Abdeckung besteht die Gefahr von
Stromschlag und Systemschäden.
Einhaltung der Richtlinien für Laser
Sun-Produkte, die mit Laser-Technologie arbeiten,
entsprechen den Anforderungen der Laser Klasse 1.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser KLasse 1
CD-ROM
Warnung – Die Verwendung von anderen
Steuerungen und Einstellungen oder die
Durchfhrung von Prozeduren, die von den
hier beschriebenen abweichen, knnen
gefhrliche Strahlungen zur Folge haben.
Conformité aux normes de sécurité
Ce texte traite des mesures de sécurité qu’il convient de
prendre pour l’installation d’un produit Sun Microsystems.
produire un court-circuit qui entraînerait des
flammes, des risques d’électrocution ou des dégâts
matériels.
Symboles
Vous trouverez ci-dessous la signification des différents
symboles utilisés :
Attention: – risques de blessures corporelles
et de dégâts matériels. Veuillez suivre les
instructions.
Attention: – surface à température élevée.
Evitez le contact. La température des surfaces
est élevée et leur contact peut provoquer des
blessures corporelles.
Attention: – présence de tensions
dangereuses. Pour éviter les risques
d’électrocution et de danger pour la santé
physique, veuillez suivre les instructions.
MARCHE – Votre système est sous tension
(courant alternatif).
Un des symboles suivants sera peut-être utilisé en fonction
du type d'interrupteur de votre système:
ARRET - Votre système est hors tension
(courant alternatif).
Mesures de sécurité
Pour votre protection, veuillez prendre les précautions
suivantes pendant l’installation du matériel :
■
■
■
Suivre tous les avertissements et toutes les
instructions inscrites sur le matériel.
Vérifier que la tension et la fréquence de la source
d’alimentation électrique correspondent à la tension et
à la fréquence indiquées sur l’étiquette de
classification de l’appareil.
Ne jamais introduire d’objets quels qu’ils soient dans
une des ouvertures de l’appareil. Vous pourriez vous
trouver en présence de hautes tensions dangereuses.
Tout objet conducteur introduit de la sorte pourrait
VEILLEUSE – L'interrupteur Marche/
Veilleuse est en position « Veilleuse ».
Modification du matériel
Ne pas apporter de modification mécanique ou électrique
au matériel. Sun Microsystems n’est pas responsable de la
conformité réglementaire d’un produit Sun qui a été
modifié.
Safety Agency Compliance Statements
xi
Positionnement d’un produit Sun
Attention: – pour assurer le bon
fonctionnement de votre produit Sun et pour
l’empêcher de surchauffer, il convient de ne
pas obstruer ni recouvrir les ouvertures
prévues dans l’appareil. Un produit Sun ne
doit jamais être placé à proximité d’un
radiateur ou d’une source de chaleur.
Attention: – Le niveau de pression acoustique
au poste de travail s'élève selon la norme DIN
45 635 section 1000, à 70 dB (A) ou moins.
Conformité SELV
Sécurité : les raccordements E/S sont conformes aux
normes SELV.
Connexion du cordon d’alimentation.
Attention: – les produits Sun sont conçus
pour fonctionner avec des alimentations
monophasées munies d’un conducteur neutre
mis à la terre. Pour écarter les risques
d’électrocution, ne pas brancher de produit
Sun dans un autre type d’alimentation secteur.
En cas de doute quant au type d’alimentation
électrique du local, veuillez vous adresser au
directeur de l’exploitation ou à un électricien
qualifié.
Attention: – tous les cordons d’alimentation
n’ont pas forcément la même puissance
nominale en matière de courant. Les rallonges
d’usage domestique n’offrent pas de
protection contre les surcharges et ne sont pas
prévues pour les systèmes d’ordinateurs. Ne
pas utiliser de rallonge d’usage domestique
avec votre produit Sun.
Attention: – votre produit Sun a été livré
équipé d’un cordon d’alimentation à trois fils
(avec prise de terre). Pour écarter tout risque
d’électrocution, branchez toujours ce cordon
dans une prise mise à la terre.
L'avertissement suivant s'applique uniquement aux
systèmes équipés d'un interrupteur VEILLEUSE:
Attention: – le commutateur d’alimentation
de ce produit fonctionne comme un dispositif
de mise en veille uniquement. C’est la prise
d’alimentation qui sert à mettre le produit
hors tension. Veillez donc à installer le produit
à proximité d’une prise murale facilement
accessible. Ne connectez pas la prise
d’alimentation lorsque le châssis du système
n’est plus alimenté.
Batterie au lithium
Attention: – sur les cartes CPU Sun, une
batterie au lithium (référence MK48T59Y,
MK48TXXB-XX, MK48T18-XXXPCZ,
M48T59W-XXXPCZ, ou MK48T08.) a été
moulée dans l’horloge temps réel SGS. Les
batteries ne sont pas des pièces remplaçables
par le client. Elles risquent d’exploser en cas
de mauvais traitement. Ne pas jeter la batterie
au feu. Ne pas la démonter ni tenter de la
recharger.
xii
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
Bloc-batterie
CD-ROM
Attention: – Les unités Product Name
contiennent une batterie étanche au plomb
(produits énergétiques portatifs n˚TLC02V50).
Il existe un risque d’explosion si ce blocbatterie est manipulé de façon erronée ou mal
mis en place. Ne remplacez ce bloc que par un
bloc-batterie Sun Microsystems du même
type. Ne le démontez pas et n’essayez pas de
le recharger hors du système. Ne faites pas
brûler la batterie mais mettez-la au rebut
conformément aux réglementations locales en
vigueur.
Attention: – L’utilisation de contrôles, de
réglages ou de performances de procédures
autre que celle spécifiée dans le présent
document peut provoquer une exposition à
des radiations dangereuses.
Normativas de seguridad
El siguiente texto incluye las medidas de seguridad que se
deben seguir cuando se instale algún producto de Sun
Microsystems.
Precauciones de seguridad
Couvercle
Pour ajouter des cartes, de la mémoire, ou des unités de
stockage internes, vous devrez démonter le couvercle de
l’unité système Sun. Ne pas oublier de remettre ce couvercle
en place avant de mettre le système sous tension.
Attention: – il est dangereux de faire
fonctionner un produit Sun sans le couvercle
en place. Si l’on néglige cette précaution, on
encourt des risques de blessures corporelles et
de dégâts matériels.
Conformité aux certifications Laser
Les produits Sun qui font appel aux technologies lasers sont
conformes aux normes de la classe 1 en la matière.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser KLasse 1
Para su protección observe las siguientes medidas de
seguridad cuando manipule su equipo:
■
■
■
Siga todas los avisos e instrucciones marcados en el
equipo.
Asegúrese de que el voltaje y la frecuencia de la red
eléctrica concuerdan con las descritas en las etiquetas
de especificaciones eléctricas del equipo.
No introduzca nunca objetos de ningún tipo a través
de los orificios del equipo. Pueden haber voltajes
peligrosos. Los objetos extraños conductores de la
electricidad pueden producir cortocircuitos que
provoquen un incendio, descargas eléctricas o daños
en el equipo.
Símbolos
En este libro aparecen los siguientes símbolos:
Precaución – Existe el riesgo de lesiones
personales y daños al equipo. Siga las
instrucciones.
Precaución – Superficie caliente. Evite el
contacto. Las superficies están calientes y
pueden causar daños personales si se tocan.
Safety Agency Compliance Statements
xiii
Precaución – Voltaje peligroso presente. Para
reducir el riesgo de descarga y daños para la
salud siga las instrucciones.
Cumplimiento de la normativa SELV
El estado de la seguridad de las conexiones de entrada/
salida cumple los requisitos de la normativa SELV.
Conexión del cable de alimentación eléctrica
Encendido – Aplica la alimentación de CA al
sistema.
Según el tipo de interruptor de encendido que su equipo
tenga, es posible que se utilice uno de los siguientes
símbolos:
Apagado - Elimina la alimentación de CA del
sistema.
En espera – El interruptor de Encendido/En
espera se ha colocado en la posición de En
espera.
Modificaciones en el equipo
No realice modificaciones de tipo mecánico o eléctrico en el
equipo. Sun Microsystems no se hace responsable del
cumplimiento de las normativas de seguridad en los
equipos Sun modificados.
Ubicación de un producto Sun
Precaución – Los productos Sun están
diseñados para trabajar en una red eléctrica
monofásica con toma de tierra. Para reducir el
riesgo de descarga eléctrica, no conecte los
productos Sun a otro tipo de sistema de
alimentación eléctrica. Póngase en contacto
con el responsable de mantenimiento o con un
electricista cualificado si no está seguro del
sistema de alimentación eléctrica del que se
dispone en su edificio.
Precaución – No todos los cables de
alimentación eléctrica tienen la misma
capacidad. Los cables de tipo doméstico no
están provistos de protecciones contra
sobrecargas y por tanto no son apropiados
para su uso con computadores. No utilice
alargadores de tipo doméstico para conectar
sus productos Sun.
Precaución – Con el producto Sun se
proporciona un cable de alimentación con
toma de tierra. Para reducir el riesgo de
descargas eléctricas conéctelo siempre a un
enchufe con toma de tierra.
Precaución – Para asegurar la fiabilidad de
funcionamiento de su producto Sun y para
protegerlo de sobrecalentamien-tos no deben
obstruirse o taparse las rejillas del equipo. Los
productos Sun nunca deben situarse cerca de
radiadores o de fuentes de calor.
Precaución – De acuerdo con la norma DIN 45
635, Parte 1000, se admite un nivel de presión
acústica para puestos de trabajo máximo de
70Db(A).
xiv
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
La siguiente advertencia se aplica solamente a equipos con
un interruptor de encendido que tenga una posición "En
espera":
Precaución – El interruptor de encendido de
este producto funciona exclusivamente como
un dispositivo de puesta en espera. El enchufe
de la fuente de alimentación está diseñado
para ser el elemento primario de desconexión
del equipo. El equipo debe instalarse cerca del
enchufe de forma que este último pueda ser
fácil y rápidamente accesible. No conecte el
cable de alimentación cuando se ha retirado la
fuente de alimentación del chasis del sistema.
internos. Asegúrese de cerrar la tapa superior antes de
volver a encender el equipo.
Precaución – Es peligroso hacer funcionar los
productos Sun sin la tapa superior colocada.
El hecho de no tener en cuenta esta precaución
puede ocasionar daños personales o
perjudicar el funcionamiento del equipo.
Aviso de cumplimiento con requisitos de láser
Los productos Sun que utilizan la tecnología de láser
cumplen con los requisitos de láser de Clase 1.
Batería de litio
Precaución – En las placas de CPU Sun hay
una batería de litio insertada en el reloj de
tiempo real, tipo SGS Núm. MK48T59Y,
MK48TXXB-XX, MK48T18-XXXPCZ,
M48T59W-XXXPCZ, o MK48T08. Las baterías
no son elementos reemplazables por el propio
cliente. Pueden explotar si se manipulan de
forma errónea. No arroje las baterías al fuego.
No las abra o intente recargarlas.
Paquete de pilas
Precaución – Las unidades Product Name
contienen una pila de plomo sellada,
Productos de energía portátil nº TLC02V50.
Existe riesgo de estallido si el paquete de pilas
se maneja sin cuidado o se sustituye de
manera indebida. Las pilas sólo deben
sustituirse por el mismo tipo de paquete de
pilas de Sun Microsystems. No las desmonte
ni intente recargarlas fuera del sistema. No
arroje las pilas al fuego. Deséchelas siguiendo
el método indicado por las disposiciones
vigentes.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser KLasse 1
CD-ROM
Precaución – El manejo de los controles, los
ajustes o la ejecución de procedimientos
distintos a los aquí especificados pueden
exponer al usuario a radiaciones peligrosas.
GOST-R Certification Mark
Tapa de la unidad del sistema
Debe quitar la tapa del sistema cuando sea necesario añadir
tarjetas, memoria o dispositivos de almacenamiento
Safety Agency Compliance Statements
xv
This page is intentionally left blank.
Norge
ADVARSEL – Litiumbatteri —
Eksplosjonsfare.Ved utskifting benyttes kun
batteri som anbefalt av apparatfabrikanten.
Brukt batteri returneres apparatleverandøren.
Sverige
VARNING – Explosionsfara vid felaktigt
batteribyte. Använd samma batterityp eller
en ekvivalent typ som rekommenderas av
apparattillverkaren. Kassera använt batteri
enligt fabrikantens instruktion.
Danmark
ADVARSEL! – Litiumbatteri —
Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri af samme
fabrikat og type. Levér det brugte batteri
tilbage til leverandøren.
Suomi
VAROITUS – Paristo voi räjähtää, jos se on
virheellisesti asennettu. Vaihda paristo
ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan
ohjeiden mukaisesti.
xvi
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
Declaration of Conformity
Compliance ID: Crystal-PCI
Product Name: Sun StorEdge PCI Dual Fibre Channel Host Adapter
This product has been tested and complies with the following rules and requirements.
EMC
USA—FCC Class B
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
European Union—EC
This equipment complies with the following requirements of the EMC Directive 89/336/EEC:
EN55022/CISPR22 (1985)
EN50082-1
Class B
IEC801-2 (1991)
4 kV (Direct), 8 kV (Air)
IEC801-3 (1984)
3 V/m
IEC801-4 (1988)
1.0 kV Power Lines, 0.5 kV Signal Lines
EN61000-3-2/IEC1000-3-2 (1994)
Pass
Safety
This equipment complies with the following requirements of the Low Voltage Directive 73/23/EEC:
EC Type Examination Certificates:
EN60950/IEC950 (1993)
EN60950 w/Nordic Deviations
Supplementary Information
This product was tested and complies with all the requirements for the CE Mark (when connected to a Sun
workstation or server).
/S/
Dennis P. Symanski
Manager, Product Compliance
/S/
DATE
John Shades
Quality Assurance Manager
Sun Microsystems, Inc.
901 San Antonio Road, M/S UMPK15-102
Palo Alto, CA 94303, USA
Sun Microsystems Scotland, Limited
Springfield, Linlithgow
West Lothian, EH49 7LR
Scotland, United Kingdom
Tel: 650-786-3255
Fax: 650-786-3723
Tel: 0506-670000
Fax: 0506 760011
DATE
xvii
This page is intentionally left blank.
xviii
Sun StorEdge PCI Single Fibre Channel Netwrok Adapter Installation Guide • December 2000
Contents
Preface
1.
xxi
Installation
1.1
1
Software Requirements
1
1.1.1
Device Drivers
1
1.1.2
SunVTS qlctest
2
1.2
Tools and Equipment Needed
1.3
Preparing for Installation
3
3
1.3.1
Sun Enterprise Systems
1.3.2
Preparing for a Sun StorEdge A5x00 Installation
1.4
Installing the Network Adapter
1.5
Testing the Installation
4
7
11
1.5.1
SunVTS
1.5.2
Testing Procedure
A. Specifications
3
11
11
A-1
A.1
PCI Card
A-1
A.2
Fibre Channel Interface Specifications
A.3
Performance Specifications
A.4
Power Requirements
A-3
A.5
Physical Dimensions
A-3
A-1
A-2
Contents
xix
xx
A.6
Regulatory Compliance
A-4
A.7
PCI Edge Connector Pin Definitions: 32-Bit Cards
A-5
A.8
PCI Edge Connector Pin Definitions: 64-Bit Cards
A-7
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
Preface
The Sun StorEdge™ PCI Single Fibre Channel Network Adapter Installation Guide
describes how to install Sun StorEdge™ PCI Single Fibre Channel Network
Adapters. These instructions are designed for an experienced system administrator
or trained service provider.
Using UNIX Commands
This document may not contain information on basic UNIX® commands and
procedures such as shutting down the system, booting the system, and configuring
devices.
See one or more of the following for this information:
■
Solaris Handbook for Sun Peripherals
■
AnswerBook™ online documentation for the Solaris™ software environment
■
Other software documentation that you received with your system
xxi
Typographic Conventions
Typeface
Meaning
Examples
AaBbCc123
The names of commands, files,
and directories; on-screen
computer output
Edit your .login file.
Use ls -a to list all files.
% You have mail.
AaBbCc123
What you type, when
contrasted with on-screen
computer output
% su
Password:
AaBbCc123
Book titles, new words or
terms, words to be emphasized
Read Chapter 6 in the User’s Guide.
These are called class options.
You must be superuser to do this.
Command-line variable;
replace with a real name or
value
To delete a file, type rm filename.
Shell Prompts
xxii
Shell
Prompt
C shell
machine_name%
C shell superuser
machine_name#
Bourne shell and Korn shell
$
Bourne shell and Korn shell superuser
#
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
Related Documentation
Application
Title
Part Number
Diagnostic Testing
SunVTS™ 3.4 User’s Guide
806-2884
SunVTS 3.4 Test Reference
806-2885
SunVTS 4.0 User’s Guide
806-2057
SunVTS 4.0 Test Reference Manual
806-2058
Sun Enterprise™ Systems
PCI I/O Board Installation and Component
Replacement
805-1372
Sun StorEdge Disk Arrays
Sun StorEdge A5000 Hardware
Configuration Guide
805-0264
Accessing Sun Documentation Online
The docs.sun.comsm web site enables you to access Sun technical documentation
on the Web. You can browse the docs.sun.com archive or search for a specific book
title or subject at:
http://docs.sun.com
Ordering Sun Documentation
Fatbrain.com, an Internet professional bookstore, stocks select product
documentation from Sun Microsystems, Inc.
For a list of documents and how to order them, visit the Sun Documentation Center
on Fatbrain.com at:
http://www1.fatbrain.com/documentation/sun
Preface
xxiii
Sun Welcomes Your Comments
Sun is interested in improving its documentation and welcomes your comments and
suggestions. You can email your comments to Sun at:
docfeedback@sun.com
Please include the part number of your document in the subject line of your email.
xxiv
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
CHAPTER
1
Installation
This chapter describes how to install the Sun StorEdge™ PCI Single Fibre Channel
Network Adapter in a system.
1.1
Software Requirements
1.1.1
Device Drivers
The minimum Solaris™ operating environment releases to support the device
drivers for the Sun StorEdge PCI Single Fibre Channel Network Adapter are:
■
■
Solaris 7 11/99
Solaris 8 6/00
TABLE 1-1
Required Packages For Installation
32-bit
64-bit
Description
SUNWfctl or
SUNWfctlx
Fibre Channel transport drivers
SUNWfcp or
SUNWfcpx
FCP (SCSI over Fibre Channel)
SUNWqlc or
SUNWqlcx
Driver for the Sun StorEdge PCI Single
Fibre Channel Network Adapter boards
SUNWcip or
SUNWcipx
IP over Fibre Channel drivers
1-1
All of the above drivers are bundled with Solaris 8. See TABLE 1-2 for driver
availability with Solaris 7.
TABLE 1-2
1.1.2
Package
Solaris 7 Release
Availability
SUNWfctl
Solaris 7 11/99
Bundled
SUNWfcp
Solaris 7 11/99
Bundled
SUNWqlc
Solaris 7
Unbundled
SUNWfcip
Solaris 7
Unbundled
■
Once installed, Sun StorEdge PCI Single Fibre Channel Network Adapter boards
will have device paths similar to
/devices/pci@b,2000/pci@2/SUNW,qlc5.
■
Under these nodes, there will be one instance of the fp driver that has a device
node similar to:
/devices/pci@b,2000/pci@2/SUNW,qlc@5/fp@0,0
■
fp driver also has a devctl node for administrative use with a name similar to
/devices/pci@b,2000/pci@2/SUNW,qlc@5/fp@0,0:devctl
■
For devices found, the nodes are created depending on the WWN of the device.
For a WWN of 2100002037182670, the device path is similar to
/devices/pci@b,2000/pci@2/SUNW,qlc@5/fp@0,0/
ssd@2100003027182670,0:a
■
Go to the http://docs.sun.com Web site, click Storage, and read the Sun
StorEdge PCI Single Fibre Channel Network Adapter Product Notes to obtain software
patch IDs.
■
The Fibre Channel transport device driver patches are at
http://sunsolve.Sun.COM
SunVTS qlctest
■
■
SunVTS must already be installed before you can do a pkgadd of the qlctest.
Release Notes are included in the SUNWvtsqc package.
TABLE 1-3
1-2
Solaris 7 Availability
qlctest Dependencies
SunVTS Release
qlctest Package
3.4
SUNWvtsqc
4.0
SUNWvtsqc
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
1.2
Tools and Equipment Needed
You may need to order fiber optic cables. You can order them in the following
lengths:
■
■
2-meter, part number X973A
15-meter, part number X978A
You will also need:
■
■
■
A No. 2 Phillips screwdriver
An antistatic wrist strap
A padded antistatic mat
1.3
Preparing for Installation
1.3.1
Sun Enterprise Systems
The Sun StorEdge PCI Single Fibre Channel Network Adapter does not support
JTAG. When you install the PCI Network Adapter in a Sun Enterprise™ system, be
sure that the corresponding PCI riser card has the JTAG jumper removed (FIGURE
1-1).
Note – If the JTAG jumper is installed, the PCI I/O board will not be recognized or
initialized during POST (power-on self-test) nor will it subsequently be recognized
by the operating system.
Chapter 1
Installation
1-3
FIGURE 1-1
1.3.2
JTAG Jumper
Preparing for a Sun StorEdge A5x00 Installation
1. Use the array’s front panel module (FPM) to ensure that the firmware level of the
interface boards is at least 1.09.
Firmware revision
must be at
least 1.09
Menu screen
FIGURE 1-2
1-4
Interface board
level 2 screen
Interface board
level 3 screen
Checking the Sun StorEdge A5x00 Array Interface Board Firmware Level
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
If the firmware level is less than 1.09, you must upgrade the firmware using an
S-Bus-based host system before you can connect the array to the Sun StorEdge PCI
Single Fibre Channel Network Adapter. The instructions for obtaining the upgrade
patch are in Step 3.
2. Determine which version of the Solaris™ operating environment you are using.
Look at the /etc/release file and make sure the operating environment installed
is at least Solaris 7. If you do not have an /etc/release file, you probably need to
upgrade you operating environment to at least Solaris 7.
3. Get the required software:
■
■
qlc driver
SunVTS™ qlctest
a. Go to the http://docs.sun.com Web site.
b. Click Storage and read the Sun StorEdge A5000 Installation Supplement and the
Sun StorEdge PCI Single Fibre Channel Network Adapter Product Notes.
The Product Notes will give you the software patch IDs.
c. Download the software patches from:
http://sunsolve.Sun.COM
Contact your support service provider if you cannot access these Web sites.
Note – Be sure to read and follow the directions in the README file for each patch.
4. Log in as root on your system.
5. Verify that the SUNWses, SUNWssad, and SUNWvts packages have been installed
on your system.
Use the /usr/bin/pkginfo command and grep for each of the above patches. For
example:
# /usr/bin/pkginfo | grep SUNWvts
system SUNWvts Online Validation Test Suite
If you are missing any of these patches, you can get them from the Updates for
Solaris Operating Environment.
6. Exit the operating environment.
To inform any mounted users that the system will be going down, use the shutdown
command. Otherwise, use the init 0 command. See the Man Pages for these
commands or the Solaris AnswerBook online documentation.
Chapter 1
Installation
1-5
7. Power off the system.
Refer to the service documentation that came with your system.
Caution – Do not disconnect the power cord at this time. This connection provides
the ground path necessary to remove and install printed circuit boards and
components without damage.
8. Choose a slot into which to install the Network Adapter.
Follow the procedures in the documentation supplied with your system.
For systems that have more than one system board, you must also select and remove
a system board that has an available PCI slot. Refer to your system documentation
for specific instructions.
9. Attach the antistatic wrist strap to your wrist and to a metal component on the
system chassis.
The wrist strap between you and the chassis provides the ground path necessary to
safely remove and install the printed circuit boards and components without
damaging them.
10. For systems with a standby-type power switch, disconnect the power cord.
Standby-type power switches have a
icon.
11. Open the system.
Refer to your system documentation for specific instructions.
Caution – If you need to remove a system board for installation, place the board on
a padded antistatic mat to prevent damage.
1-6
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
1.4
Installing the Network Adapter
1. Pull the dust coverout of the 1x9 optical transceiver (OT) connectors (FIGURE 1-3).
FIGURE 1-3
Sun StorEdge PCI Single Fibre Channel Network Adapter Dust Covers
2. Install the Network Adapter in the PCI slot you have chosen.
Installation details vary for each system. Refer to your system documentation for
specific instructions.
3. Reassemble the system.
Refer to your system documentation for specific instructions.
4. Disconnect the wrist strap.
5. Push the fiber optic cable connector into the OT connector until you hear a click
(FIGURE 1-4).
Caution – Fiber optic cables have keyed connectors; they can only be inserted into
OT connectors as shown in FIGURE 1-4.
Chapter 1
Installation
1-7
FIGURE 1-4
Connecting a Fiber Optic Cable to an OT Connector
6. Connect the other end of the fiber optic cable to a device such as a disk array or
hub.
Refer to the documentation that came with the device for specific instructions.
7. Power on your peripherals and then your system.
Note – If your system starts to reboot, interrupt the reboot process by pressing the
Stop-A keys.
The system should now be at the ok prompt. If a > prompt is showing, type n to
switch to the ok prompt.
8. Make sure that the system recognizes the Network Adapter.
Use either Method A or Method B.
a. For Method A, see FIGURE 1-5 and FIGURE 1-6.
FIGURE 1-6 is a continuation of FIGURE 1-5.
b. For Method B, see FIGURE 1-7.
1-8
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
ok show-devs
/counter-timer@f,1c00
/pci@f,2000
/pci@f,4000
/counter-timer@e,1c00
/fhc@e,f8800000
/pci@e,2000
/pci@e,4000
/counter-timer@b,3c00
/fhc@a,f8800000
/sbus@a,0
/counter-timer@3,3c00
/sbus@3,0
/fhc@2,f8800000
/disk-board@6,0
/SUNW,UltraSPARC-II@5,0
/SUNW,UltraSPARC-ii@4,0
/fhc@4,f8800000
/SUNW,UltraSPARC-II@1,0
/SUNW,UltraSPARC-11@0,0
/fhc@0,f8800000
/central@1f,0
/virtual-memory
/memory@0,0
/aliases
/options
/openprom
/chosen
/packages
/pci@f,4000/SUNW,isptwo@3
/pci@f,4000/SUNW,isptwo@3/st
/pci@f,4000/SUNW,isptwo@3/sd
/fhc@e,f8800000/sbus-speed@0,500000
/fhc@e,f8800000/eeprom@0,300000
/fhc@e,f8800000/flashprom@0,0
/fhc@e,f8800000/environment@0,400000
/fhc@e,f8800000/ac@0,1000000
/pci@e,2000/pci@2
/pci@e,2000/pci@2/SUNW,qlc@5
/pci@e,2000/pci@2/SUNW,qlc@4
/pci@e,2000/pci@2/SUNW,qlc@5/fp@0,0
/pci@e,2000/pci@2/SUNW,qlc@5/fp@0,0/disk
/pci@e,2000/pci@2/SUNW,qlc@4/fp@0,0
/pci@e,2000/pci@2/SUNW,qlc@4/fp@0,0/disk
FIGURE 1-5
System Recognition of the Network Adapter, Method A, Part 1
Chapter 1
Installation
1-9
ok apply show-children /pci@e,2000/pci@2/SUNW,qlc@5
LiD HA --- Port WWN --- ----- ---- Disk description ---_3d 3d 5080020000025a5a SUN ----- SENA ---------- 1.09PZX
_30 30 21000020370e6891 SEAGATE - ST19171FCSUN9.0G177E9823U86993
_33 33 21000020370e964f SEAGATE - ST19171FCSUN9.0G177E9823V06714
_36 36 21000020370e92c9 SEAGATE - ST19171FCSUN9.0G177E9823V11851
_2d 2d 5080020000025a59 SUN ----- SENA ---------- 1.09PZX
_23 23 21000020370e930d SEAGATE - ST19171FCSUN9.0G177E9823V12050
_26 26 21000020370e9b08 SEAGATE - ST19171FCSUN9.0G177E9823V15713
FIGURE 1-6
System Recognition of the Network Adapter, Method A, Part 2
In FIGURE 1-6, /pci@1f,0/pci@1/pc1@1/SUNW,qlc@4 is one port on the Sun
StorEdge PCI Single Fibre Channel Network Adapter and the disks are in a Sun
StorEdge A5000 array (SENA).
ok select /pci@e,2000/pci@2/SUNW,qlc@5
ok show-children
LiD HA --- Port WWN --- ----- ---- Disk description ---_3d 3d 5080020000025a5a SUN ----- SENA ---------- 1.09PZX
_30 30 21000020370e6891 SEAGATE - ST19171FCSUN9.0G177E9823U86993
_33 33 21000020370e964f SEAGATE - ST19171FCSUN9.0G177E9823V06714
_36 36 21000020370e92c9 SEAGATE - ST19171FCSUN9.0G177E9823V11851
_2d 2d 5080020000025a59 SUN ----- SENA ---------- 1.09PZX
_23 23 21000020370e930d SEAGATE - ST19171FCSUN9.0G177E9823V12050
_26 26 21000020370e9b08 SEAGATE - ST19171FCSUN9.0G177E9823V15713
FIGURE 1-7
System Recognition of the Network Adapter, Method B
Note – The probe-scsi-all command does not function identically on all
platforms, and does not in all cases probe for fiber channel devices. The
probe-fcal-all command exists only on Sun Enterprise™ systems.
9. Reboot your system using the boot -r command.
1-10
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
1.5
Testing the Installation
1.5.1
SunVTS
Refer to the SunVTS documents in TABLE 1-4.
TABLE 1-4
Sun VTS Documents
Application
Title
Part Number
Diagnostic Testing
SunVTS 3.4 User’s Guide
806-2884
SunVTS 3.4 Test Reference
806-2885
Sun VTS 4.0 User’s Guide
806-2057
Sun VTS 4.0 Test Reference Manual
806-2058
SunVTS is a diagnostic program that exercises your system to verify the
functionality, reliability, and configuration of your Network Adapter. You will need
to install both the 32- and 64-bit versions of SunVTS. In addition, you will need the
SunVTS qlc test package—SUNWvtsqc—installed.
Once you have the SUNWvtsqc package installed, you may run the qlctest under
SunVTS.
1.5.2
Testing Procedure
1. To invoke SunVTS locally on a system running CDE, type the following as root:
# cd /opt/SUNWvts/bin
# ./sunvts
2. From the SunVTS menus select the following:
a. Select devices None and select intervention.
b. Select mode Functional test.
c. Select Host Adapter qlcx where x is the qlc # of the qlc port you want to run
this test against.
Chapter 1
Installation
1-11
d. If you want to run the external loopback test, place a loopback plug into the qlc
port that you want to test.
If you do not have an external loopback plug, you can make one by taking apart
a fiber cable and plug the same cable into the transmitter and receiver of the qlc
port.
e. Right click on the qlc test and select Test Parameter Options.
f. Enable the External Loopback Test.
Note – If you do not use a loopback plug, you can connect the qlc port to storage
devices. In such a case, you will be testing both the qlc and the entire fiber loop.
g. Select Start to start the test.
Note – If you select only the external loopback test, the different version diagnostic
tests will not be run and the delay time between tests will be set to zero. This is a
good way to test your fiber loop if you leave the qlc port attached to storage devices.
1-12
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
This page is intentionally left blank.
Chapter 1
Installation
1-13
1-14
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
APPENDIX
A
Specifications
A.1
PCI Card
The Sun StorEdge PCI Single Fibre Channel Network Adapter is a Fibre Channel PCI
card with one onboard optical transceiver. This Network Adapter is PCI Version 2.1
compliant.
A.2
Fibre Channel Interface Specifications
TABLE A-1
Fibre Channel Specifications
Specification
Value
ANSI Standards
Fibre Channel FC-PH X3.230-1995
SCSI Fibre Channel Protocol X3.269-1996
Optical transceiver
100 MBytes/sec (1 Gbits/sec) full duplex
Shortwave laser, Module Definition 5
Fiber cable type
50 micrometer multimode
Maximum cable length
500 meters
A-1
A.3
Performance Specifications
The following specifications must be verified.
TABLE A-2
A-2
Performance Specifications
Feature
Specification
PCI clock
66 MHz maximum
PCI data burst transfer rate
528 MBytes/sec burst rate
FC-AL transfer rate payload
100 MBytes/sec
PCI data/address lines
AD63-0
PCI modes
Master/slave
Capacitance per PCI signal line
≤10 pF, except for CLK between 5 to 12 pF and
IDSEL ≤8 pF
FC-AL Interface
1 Gbit optical (1.0625 Gbits/sec)
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
A.4
Power Requirements
TABLE A-3
A.5
Power Requirements
Specification
Rating
Voltage and current
5V 5%,3A
Ripple
100 mV
Physical Dimensions
TABLE A-4
Physical Dimensions
Height
Width
Depth
Weight
15 mm
106.68 mm
174.63 mm
100 g
0.6 in.
4.2 in.
6.875 in.
3.6 oz.
Appendix A
Specifications
A-3
A.6
Regulatory Compliance
TABLE A-5
Requirements Met or Exceeded by the Network Adapter
Category
Rating
Safety
UL 1950
CSA 950
TUV EN 60950
Class 1 laser requirements per CFR 21, Part 1040 and IEC 825
RFI/EMI
FCC Class B
DOC Class B
VCCI Class B
EMC Directive (89/336/EEC), EN55022
Immunity
A-4
EMC Directive (89/336/EEC), EN55082-1
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
A.7
PCI Edge Connector Pin Definitions:
32-Bit Cards
TABLE A-6
PCI Edge Connector Pin Definitions, 32-Bit Cards (Top)
Pin
Description
Pin
Description
Pin
Description
1
-12V
22
GND
43
+3.3V
2
TCK
23
AD27
44
C_BE1
3
GND
24
AD25
45
AD14
4
TDO
25
+3.3V
46
GND
5
+5V
26
C_BE3
47
AD12
6
+5V
27
AD23
48
AD10
7
INTB
28
GND
49
GND
8
INTD
29
AD21
50
KEYWAY
9
GND (PRSNT1)
30
AD19
51
KEYWAY
10
RESERVED
31
+3.3V
52
AD08
11
GND (PRSNT2)
32
AD17
53
AD07
12
KEYWAY
33
C_BE2
54
+3.3V
13
KEYWAY
34
GND
55
AD05
14
RESERVED
35
IRDY
56
AD03
15
GND
36
+3.3V
57
GND
16
CLK
37
DEVSEL
58
AD01
17
GND
38
GND
59
+5V
18
REQ
39
LOCK
60
ACK64
19
+3V/+5V
40
PERR
61
+5V
20
AD31
41
+3.3V
62
+5V
21
AD29
42
SERR
Appendix A
Specifications
A-5
TABLE A-7
A-6
PCI Edge Connector Pin Definitions, 32-Bit Cards(Bottom)
Pin
Description
Pin
Description
Pin
Description
1
TRST
22
AD28
43
PAR
2
+12V
23
AD26
44
AD15
3
TMS
24
GND
45
+3.3V
4
TDI
25
AD24
46
AD13
5
+5V
26
IDSEL
47
AD11
6
INTA
27
+3.3V
48
GND
7
INTC
28
AD22
49
AD09
8
+5V
29
AD20
50
KEYWAY
9
RESERVED
30
GND
51
KEYWAY
10
+5V
31
AD18
52
C_BE0
11
RESERVED
32
AD16
53
+3.3V
12
KEYWAY
33
+3.3V
54
AD06
13
KEYWAY
34
FRAME
55
AD04
14
RESERVED
35
IGND
56
GND
15
RST
36
TRDY
57
GND
16
+5V
37
GND
58
AD02
17
GNt
38
STOP
59
+5V
18
GND
39
+3.3V
60
REQ64
19
RESERVED
40
SDONE
61
+5V
20
AD30
41
SBO
62
+5V
21
+3.3V
42
GND
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000
A.8
PCI Edge Connector Pin Definitions:
64-Bit Cards
TABLE A-8
PCI Expansion Board Pinout—Universal Board
Pin
Side B
Side A
Pin
Side B
Side A
1
-12V
TRST#
26
C/BE[3]#
IDSEL
2
TCK
+12V
27
AD[23]
+3.3V
3
Ground
TMS
28
Ground
AD[22]
4
TDO
TDI
29
AD[21]
AD[20]
5
+5V
+5V
30
AD[19]
Ground
6
+5V
INTA#
31
+3.3V
AD[18}
7
INTB#
INTC#
32
AD[17]
AD[16]
8
INTD#
+5V
33
C/BE[2]#
+3.3V
9
PRSNT1#
Reserved
34
Ground
FRAME#
10
Reserved
+VI/O
35
IRDY#
Ground
11
PRSNT2#
Reserved
36
+3.3V
TRDY#
12
Keyway
Keyway
37
DEVSEL#
Ground
13
Keyway
Keyway
38
Ground
STOP#
14
Reserved
3.3Vaux
39
LOCK#
+3.3V
15
Ground
RST#
40
PERR#
SDONE
16
CLK
+VI/O
41
+3.3V
SBO#
17
Ground
GNT#
42
SERR#
Ground
18
REQ#
Ground
43
+3.3V
PAR
19
+VI/O
PME#
44
C/BE[1]#
AD[15]
20
AD[31]
AD[30]
45
ad[14]
+3.3V
21
AD[29]
+3.3V
46
Ground
AD[13]
22
Ground
AD[28]
47
AD[12]
AD[11]
23
AD[27]
AD[26]
48
AD[10]
Ground
24
AD[25]
Ground
49
M66EN
AD[09]
25
+3.3V
AD[24]
50
Keyway
Keyway
Appendix A
Specifications
A-7
TABLE A-9
A-8
PCI Expansion Board Pinout—Universal Board
Pin
Side B
Side A
Pin
Side B
Side A
51
Keyway
Keyway
76
Ground
AD[52]
52
AD[08]
C/BE[0]#
77
AD[51]
AD[50]
53
AD[07]
+3.3V
78
AD[49]
Ground
54
+3.3V
AD[06]#
79
+VI/O
AD[48]
55
AD[05]
AD[04]#
80
AD[47]
AD[46]
56
AD[03]
Ground
81
AD[45]
Ground
57
Ground
AD[02]
82
Ground
AD[44]
58
AD[01]
AD[00]
83
AD[43]
AD[42]
59
+VI/O
+VI/O
84
AD[41]
+VI/O
60
ACK64#
REQ64#
85
Ground
AD[40]
61
+5V
+5V
86
AD[39]
AD[38]
62
+5V
+5V
87
AD[37]
Ground
Keyway
Keyway
88
+VI/O
AD[36]
Keyway
Keyway
89
AD[35]
AD[34]
63
Reserved
Ground
90
AD[33]
Ground
64
Ground
C/BE[7]#
91
Ground
AD[32]
65
C/BE[6]#
C/BE[5]#
92
Reserved
Reserved
66
C/BE[4]#
+VI/O
93
Reserved
Ground
67
Ground
PAR64
94
Ground
Reserved
68
AD[63]
AD[62]
69
AD[61]
Ground
70
+VI/O
AD[60]
71
AD[59]
AD[58]
72
AD[57]
Ground
73
Ground
AD[56]
74
AD[55]
AD[54]
75
AD[53]
+VI/O
Sun StorEdge PCI Single Fibre Channel Network Adapter Installation Guide • December 2000