superserver 1026t-urf superserver 1026t-uf

SUPER
®
SUPERSERVER 1026T-URF
SUPERSERVER 1026T-UF
USER’S MANUAL
1.0b
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other reproductive harm.
Manual Revision 1.0b
Release Date: December 18, 2012
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2012 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer 1026TURF/1026T-UF. Installation and maintenance should be performed by experienced
technicians only.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the
server system and describes the main features of the X8DTU-F serverboard and
the SC113TQ-R650UB/SC113TQ-560UB chassis, which comprise the SuperServer
1026T-URF/1026T-UF.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer into a rack and
check out the server configuration prior to powering up the system. If your server
was ordered without processor and memory components, this chapter will refer you
to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 1026T-URF/1026T-UF.
iii
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X8DTU-F serverboard, including the
locations and functions of connections, headers and jumpers. Refer to this chapter
when adding or removing processors or main memory and when reconfiguring the
serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC113TQ-R650UB/SC113TQ560UB server chassis. You should follow the procedures given in this chapter when
installing, removing or reconfiguring SATA or peripheral drives and when replacing
system power supply modules and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed information on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: Installing Windows
Appendix C: System Specifications
iv
Preface
Notes
v
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Table of Contents
Chapter 1 Introduction
1-1
Overview ......................................................................................................... 1-1
1-2
Serverboard Features ..................................................................................... 1-2
Processors ...................................................................................................... 1-2
Memory ........................................................................................................... 1-2
UIO .................................................................................................................. 1-2
Serial ATA ....................................................................................................... 1-2
Onboard Controllers/Ports .............................................................................. 1-2
Graphics Controller ......................................................................................... 1-3
Other Features ................................................................................................ 1-3
1-3
Server Chassis Features ................................................................................ 1-3
System Power ................................................................................................. 1-3
PCI Expansion Slots ....................................................................................... 1-3
Control Panel .................................................................................................. 1-3
I/O Backplane.................................................................................................. 1-4
Cooling System ............................................................................................... 1-4
1-4
Contacting Supermicro .................................................................................... 1-6
Chapter 2 Server Installation
2-1
Overview ......................................................................................................... 2-1
2-2
Unpacking the System .................................................................................... 2-1
2-3
Preparing for Setup ......................................................................................... 2-1
Choosing a Setup Location ............................................................................. 2-1
2-4
Warnings and Precautions .............................................................................. 2-2
Rack Precautions ............................................................................................ 2-2
Server Precautions.......................................................................................... 2-2
Rack Mounting Considerations ....................................................................... 2-3
Ambient Operating Temperature ................................................................ 2-3
Reduced Airflow ......................................................................................... 2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading ..................................................................................... 2-3
Reliable Ground ......................................................................................... 2-3
2-5
Installing the System into a Rack ................................................................... 2-4
Identifying the Sections of the Rack Rails ...................................................... 2-4
Inner Rails ....................................................................................................... 2-5
Outer Rails ...................................................................................................... 2-6
Installing the Server into a Telco Rack ........................................................... 2-9
vi
Table of Contents
2-6
Checking the Serverboard Setup ...................................................................2-11
2-7
Checking the Drive Bay Setup ...................................................................... 2-12
Chapter 3 System Interface
3-1
Overview ......................................................................................................... 3-1
3-2
Control Panel Buttons ..................................................................................... 3-1
Reset ............................................................................................................... 3-1
Power .............................................................................................................. 3-1
UID .................................................................................................................. 3-1
3-3
Control Panel LEDs ........................................................................................ 3-2
Universal Information LED .............................................................................. 3-2
NIC2 ................................................................................................................ 3-3
NIC1 ................................................................................................................ 3-3
HDD................................................................................................................. 3-3
Power .............................................................................................................. 3-3
3-4
Hard Drive Carrier LEDs ................................................................................. 3-4
Chapter 4 Standardized Warning Statements for AC Systems
4-1
About Standardized Warning Statements ....................................................... 4-1
Warning Definition ........................................................................................... 4-1
Installation Instructions.................................................................................... 4-4
Circuit Breaker ................................................................................................ 4-5
Power Disconnection Warning ........................................................................ 4-6
Equipment Installation ..................................................................................... 4-8
Restricted Area................................................................................................ 4-9
Battery Handling............................................................................................ 4-10
Redundant Power Supplies .......................................................................... 4-12
Backplane Voltage ........................................................................................ 4-13
Comply with Local and National Electrical Codes ........................................ 4-14
Product Disposal ........................................................................................... 4-15
Hot Swap Fan Warning ................................................................................. 4-16
Power Cable and AC Adapter ...................................................................... 4-18
Chapter 5 Advanced Serverboard Setup
5-1
Handling the Serverboard ............................................................................... 5-1
Precautions ..................................................................................................... 5-1
Unpacking ....................................................................................................... 5-1
5-2
Processor and Heatsink Installation................................................................ 5-2
Installing LGA1366 Processors ....................................................................... 5-2
Installing the Heatsink ..................................................................................... 5-4
Removing the Heatsink ................................................................................... 5-5
vii
SUPERSERVER 1026T-URF/1026T-UF User's Manual
5-3
Connecting Cables .......................................................................................... 5-6
Connecting Data Cables ................................................................................. 5-6
Connecting Power Cables .............................................................................. 5-6
Connecting the Control Panel ......................................................................... 5-6
5-4
I/O Ports .......................................................................................................... 5-7
5-5
Installing Memory ............................................................................................ 5-8
5-6
Adding PCI Cards ......................................................................................... 5-10
5-7
Serverboard Details .......................................................................................5-11
X8DTU-F Quick Reference ........................................................................... 5-12
5-8
Connector Definitions .................................................................................... 5-13
5-9
Jumper Settings ............................................................................................ 5-19
5-10
Onboard Indicators........................................................................................ 5-22
5-11
SATA Port Connections ................................................................................. 5-23
5-12
Installing Software ......................................................................................... 5-24
Supero Doctor III ........................................................................................... 5-25
Chapter 6 Advanced Chassis Setup
6-1
Static-Sensitive Devices .................................................................................. 6-1
Precautions ..................................................................................................... 6-1
6-2
Control Panel .................................................................................................. 6-2
6-3
System Cooling ............................................................................................... 6-2
System Fan Failure ......................................................................................... 6-3
6-4
Drive Bay Installation/Removal ....................................................................... 6-4
Accessing the Drive Bays ............................................................................... 6-4
Hard Drive Installation..................................................................................... 6-4
DVD Drive Installation ..................................................................................... 6-6
6-5
Power Supply .................................................................................................. 6-8
1026T-URF ...................................................................................................... 6-8
1026T-UF ........................................................................................................ 6-9
Chapter 7 BIOS
7-1
Introduction...................................................................................................... 7-1
7-2
Main Setup ...................................................................................................... 7-2
7-3
Advanced Setup Configurations...................................................................... 7-4
7-4
Security Settings ........................................................................................... 7-21
7-5
Boot Configuration ........................................................................................ 7-23
7-6
Exit Options ................................................................................................... 7-24
Appendix A BIOS Error Beep Codes
Appendix B Installing Windows
Appendix C System Specifications
viii
Chapter 1: Introduction
Chapter 1
Introduction
1-1
Overview
The SuperServer 1026T-URF/1026T-UF is a high-end server comprised of two
main subsystems: the SC113TQ-R650UB//SC113TQ-560UB 1U chassis and the
X8DTU-F serverboard. Please refer to our web site for information on operating
systems that have been certified for use with the system (www.supermicro.com).
Note: a complete list of safety warnings is provided on the Supermicro web site at
http://www.supermicro.com/about/policies/safety_information.cfm
In addition to the serverboard and chassis, various hardware components have
been included with the 1026T-URF/1026T-UF, as listed below:
•
One slim DVD-ROM drive (DVM-TEAC-DVD-SBT)
•
One mini USB to SATA adapter (CDM-USATA-G)
•
Four sets of 4-cm counter-rotating fans (FAN-0086L4)
•
One air shroud (MCP-310-19002-0N)
•
One DVD-ROM drive cable (CBL-0061)
•
One internal USB cable for DVD drive (CBL-0341L)
•
Two passive CPU heatsinks (SNK-P0037P)
•
•
Riser Cards: (see Section 5-6 for details)
One RSC-R1UU-UE16 for PCI-E card
Hard Drive Accessories
One SAS/SATA backplane (BPN-SAS-113TQ)
Two SAS/SATA iPASS cables (CBL-0287L, CBL-0288L)
Eight SAS/SATA drive carriers (MCP-220-00047-B)
•
One rackmount kit (MCP-290-00043-0V)
•
One CD containing drivers and utilities
•
SuperServer 1026T-URF/1026T-UF User's Manual
1-1
SUPERSERVER 1026T-URF/1026T-UF User's Manual
1-2
Serverboard Features
At the heart of the SuperServer 1026T-URF/1026T-UF lies the X8DTU-F, a dual
processor serverboard based on the Intel® IOH-36D + ICH10R chipset. Below
are the main features of the X8DTU-F. (See Figure 1-1 for a block diagram of the
chipset).
Processors
The X8DTU-F supports single or dual two Intel® 5500 Series processors in
LGA1366 sockets. Please refer to our web site for a complete listing of supported
processors (www.supermicro.com).
Memory
The X8DTU-F has 240-pin DIMM sockets that can support up to 96 GB of registered ECC DDR3-1333/1066/800 SDRAM. Please refer to Chapter 5 for installing
memory.
UIO
The X8DTU-F is a specially-designed serverboard that features Supermicro's UIO
(Universal I/O) technology. UIO serverboards have a PCI Express x8 slot that can
support any one of several types of UIO card types to add SAS ports, additional
LAN ports, etc. to the serverboard. This allows the user to tailor the serverboard
to their own needs.
Note: the server does not come with a UIO card installed.
Serial ATA
An on-chip (ICH10R) SATA controller is integrated into the X8DTU-F to provide a
six-port, 3 Gb/sec SATA subsystem, which is RAID 0, 1, 5 and 10 supported. The
SATA drives are hot-swappable units.
Note: You must have RAID set up to enable the hot-swap capability of the SATA
drives. Documentation on RAID setup guidelines can be found on our web site.
Onboard Controllers/Ports
The color-coded I/O ports include one COM port, a VGA (monitor) port, two USB
2.0 ports, PS/2 mouse and keyboard ports, one IPMI dedicated LAN port and two
gigabit Ethernet ports.
1-2
Chapter 1: Introduction
Graphics Controller
The X8DTU-F features an integrated Matrox G200eW graphics chip, which includes
8 MB of DDR2 memory.
Other Features
Other onboard features that promote system health include onboard voltage monitors, auto-switching voltage regulators, chassis and CPU overheat sensors, virus
protection and BIOS rescue.
1-3
Server Chassis Features
The SC113 features eight 2.5" hard drive bays and high-efficiency power supplies.
The 1026T-URF is built upon the SC113TQ-R650UB chassis while the 1026T-UF
is built upon the SC113TQ-560UB chassis. Details on the chassis and on servicing
procedures can be found in Chapter 6.The following is a general outline of the main
features of both chassis.
System Power
The SC113TQ-R650UB features a redundant 650W power supply consisting of
two power modules. The system does not need to be shut down when replacing or
removing a single power supply module.
The SC113TQ-560UB features a single 560W power supply module. The system
must be shut down when replacing or removing this power supply module.
PCI Expansion Slots
A riser card (RSC-R1UU-E8PR, optional) on the right side of the chassis can support AOC-PG-i2+ add-on card to provide two Gb LAN ports. The left side supports
a UIO card and one PCI-E x16 card. These two systems can support four SAS/
SATA drives with an optional UIO SAS card. See our web site for details (http://
www.supermicro.com/products/nfo/UIO.cfm).
See page 5-10 for details. (Right and left refer to the side when viewed from the
front of the system.
Control Panel
The SC113 control panel provides important system monitoring and control information. LEDs indicate power on, network activity, hard disk drive activity and a UID
(Universal Information) LED. Also present are a main power button, a system reset
button and a UID button.
1-3
SUPERSERVER 1026T-URF/1026T-UF User's Manual
I/O Backplane
The SC113 is a 1U rackmount chassis. Its I/O backplane provides three standard
size PCI slots, one COM port, one VGA port, two USB ports, PS/2 mouse and
keyboard ports, two Ethernet (LAN) ports, one dedicated IPMI LAN port and a
UID LED.
Cooling System
The SC113 chassis' revolutionary cooling design has been optimized to provide
sufficient cooling for dual CPU configurations. The chassis includes an air shroud
and four 4-cm counter-rotating fans located in the middle of the chassis. There is a
"Fan Speed Control Mode" in BIOS that allows chassis fan speed to be determined
by system temperature.
1-4
Chapter 1: Introduction
Figure 1-1. Intel IOH-36D/ICH10R Chipset:
System Block Diagram
F
C
PCI-E x16
QPI
Gen2 x16
E
QPI
Port 1
Port 0
Gen2 x4 Intel 82576
Ports 7,8,9,10 Ports 1,2
(Lane Reversal)
Intel 5520
Gen2 x8
RJ45RJ45
Ports 5,6
Ports 3,4 ESI CLINK
SST
25VF016
Gen2 x8
SPI
(Lane Reversal)
ESI CLINK
PCI- E Ports 1-6
Ports
Intel ICH10R
8,10
PCI
COMA
COMB
USB
SATA
LPC
USB
SATA 0
USB 0/1
SIO
BMC
USB 2/3
SATA 1
W83527HG
SATA 2
USB 4/5
SATA 3
USB 6/7
SATA 4
SATA 5
RJ45
VGA
PS2 KB/MS
1-5
F
DDR3 DIMM
E
CPU 2
CPU 1
DDR3 DIMM
D
DDR3 DIMM
DDR3 DIMM
B
PCI-E x8
B
QPI
A
PCI-E x8
in x4 Slot
C
DDR3 DIMM
DDR3 DIMM
Note: This is a general block diagram. Please see Chapter 5 for details.
SUPERSERVER 1026T-URF/1026T-UF User's Manual
1-4
Contacting Supermicro
Headquarters
Address:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel:
+1 (408) 503-8000
Fax:
+1 (408) 503-8008
Email:
marketing@supermicro.com (General Information)
support@supermicro.com (Technical Support)
Web Site:
www.supermicro.com
Europe
Address:
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel:
+31 (0) 73-6400390
Fax:
+31 (0) 73-6416525
Email:
sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
Asia-Pacific
Address:
Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd
Chung-Ho Dist., New Taipei City 235
Taiwan
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3991
Web Site:
www.supermicro.com.tw
Technical Support:
Email:
support@supermicro.com.tw
Tel:
+886-(2)-8226-3990
1-6
Chapter 2: Server Installation
Chapter 2
Server Installation
2-1
Overview
This chapter provides a quick setup checklist to get your SuperServer 1026TURF/1026T-UF up and running. Following these steps in the order given should
enable you to have the system operational within a minimum amount of time.
This quick setup assumes that server system has come to you with the processors and memory preinstalled. If your system is not already fully integrated with a
serverboard, processors, system memory etc., please turn to the chapter or section
noted in each step for details on installing specific components.
2-2
Unpacking the System
You should inspect the box the SuperServer 1026T-URF/1026T-UF was shipped
in and note if it was damaged in any way. If the server itself shows damage you
should file a damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the server. It should
be situated in a clean, dust-free area that is well ventilated. Avoid areas where
heat, electrical noise and electromagnetic fields are generated. You will also need
it placed near a grounded power outlet. Read the Rack and Server Precautions in
the next section.
2-3
Preparing for Setup
The box the SuperServer 1026T-URF/1026T-UF was shipped in should include two
sets of rail assemblies, two rail mounting brackets and the mounting screws you
will need to install the system into the rack. Follow the steps in the order given to
complete the installation process in a minimum amount of time. Please read this
section in its entirety before you begin the installation procedure outlined in the
sections that follow.
Choosing a Setup Location
•
Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufficient airflow and ease in servicing.This product is for
2-1
SUPERSERVER 1026T-URF/1026T-UF User's Manual
installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).
•
This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display Units.
2-4
Warnings and Precautions
Rack Precautions
•
•
•
•
Ensure that the leveling jacks on the bottom of the rack are fully extended to
the floor with the full weight of the rack resting on them.
In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
Always make sure the rack is stable before extending a component from the
rack.
You should extend only one component at a time - extending two or more simultaneously may cause the rack to become unstable.
Server Precautions
•
•
•
•
•
•
Review the electrical and general safety precautions in Chapter 4.
Determine the placement of each component in the rack before you install the
rails.
Install the heaviest server components on the bottom of the rack first, and then
work up.
Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
Allow the hot plug drives and power supply modules to cool before touching
them.
Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.
2-2
Chapter 2: Server Installation
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient temperature (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connections other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).
2-3
SUPERSERVER 1026T-URF/1026T-UF User's Manual
2-5
Installing the System into a Rack
This section provides information on installing the SuperServer 1026T-URF/1026TUF into a rack. If the system has already been mounted into a rack, you can skip
ahead to Sections 2-5 and 2-6. Note: This rail will fit a rack between 26" and 33.5"
deep.
There are a variety of rack units on the market, which may mean the assembly
procedure will differ slightly. The following is a guideline for installing the 1026TURF/1026T-UF into a rack with the rack rails provided. You should also refer to the
installation instructions that came with the rack unit you are using.
Identifying the Sections of the Rack Rails
Each assembly consists of two sections: an inner fixed chassis rail that secures
directly to the server chassis and an outer fixed rack rail that secures directly to
the rack itself.
Figure 2-1. Identifying the Sections of the Rack Rails
Outer Rails
Rail Extension
(Inner rail is pre-installed)
2-4
Chapter 2: Server Installation
Inner Rails
The SC113 chassis includes a set of inner rails in two sections: inner rails and inner
rail extensions. The inner rails are pre-attached and do not interfere with normal use
of the chassis if you decide not to use a server rack. Attach the inner rail extension
to stabilize the chassis within the rack.
Installing the Inner Rails (Figure 2-2)
1. Place the inner rack extensions on the side of the chassis aligning the hooks
of the chassis with the rail extension holes. Make sure the extension faces
"outward" just like the pre-attached inner rail.
2. Slide the extension toward the front of the chassis.
3. Secure the chassis with two screws as illustrated.
4. Repeat steps 1-3 for the other inner rail extension.
Figure 2-2. Installing Chassis Rails
1
2
3
2-5
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Outer Rails
Installing the Outer Rails to the Rack (Figures 2-3 and 2-4)
1. Attach the short bracket to the outside of the long bracket. You must align the
pins with the slides. Also, both bracket ends must face the same direction.
2. Adjust both the short and long brackets to the proper distance so that the rail
fits snugly into the rack.
3. Secure the long bracket to the front side of the outer rail with two M5 screws
and the short bracket to the rear side of the outer rail with three M5 screws.
4. Repeat steps 1-4 for the left outer rail.
Figure 2-3. Assembling the Outer Rails
Secure to the
Front of the Rack
Attach Outer Racks
Together
Secure to the
Rear of the Rack
Warning: do not pick up the server with the front handles. They are designed to pull the system from a rack only.
Warning! Stability hazard. The rack stabilizing mechanism must be in
place, or the rack must be bolted to the floor before you slide the unit out
for servicing. Failure to stabilize the rack can cause the rack to tip over.
2-6
Chapter 2: Server Installation
3
3
2
SCALE 0.380
Figure 2-4. Installing the Outer Rails to the Rack
2-7
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Installing the Server into a Rack (Figure 2-5)
1. Confirm that chassis includes the inner rails and rail extensions . Also, confirm
that the outer rails are installed on the rack.
2. Line chassis rails with the front of the rack rails.
3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click".
4. (Optional) Insert and tightening the thumbscrews that hold the front of the
server to the rack.
Figure 2-5. Installing the Server into a Rack
2-8
Chapter 2: Server Installation
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:
•
This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
•
When mounting this unit in a partially filled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
•
If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
Installing the Server into a Telco Rack
To install the SuperServer 1026T-URF/1026T-UF into a Telco type rack, use two
L-shaped brackets on either side of the chassis (four total). First, determine how
far follow the server will extend out the front of the rack. Larger chassis should be
positioned to balance the weight between front and back. If a bezel is included on
your server, remove it. Then attach the two front brackets to each side of the chassis, then the two rear brackets positioned with just enough space to accommodate
the width of the telco rack. Finish by sliding the chassis into the rack and tightening
the brackets to the rack.
2-9
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Figure 2-6. Installing the Server into a Telco Rack
2-10
Chapter 2: Server Installation
2-6
Checking the Serverboard Setup
After you install the 1026T-URF/1026T-UF in the rack, you will need to open the
unit to make sure the serverboard is properly installed and all the connections
have been made.
Removing the Chassis Cover (Figure 2-5)
1. Grasp the two handles on either side and pull the unit straight out until it
locks (you will hear a "click").
2. Remove the screws securing the top cover to the chssis.
3. Slide the cover toward the rear of the chassis.
4. Lift the cover off the chassis.
Checking the Components
1. You should have one or two processors already installed into the serverboard.
Each processor needs its own heatsink. See Chapter 5 for instructions on
processor and heatsink installation.
Figure 2-5: Removing the Chassis Cover
3
2
2-11
SUPERSERVER 1026T-URF/1026T-UF User's Manual
2. Your server system may have come with system memory already installed.
Make sure all DIMMs are fully seated in their slots. For details on adding
system memory, refer to Chapter 5.
3. If desired, you can install add-on cards to the system. See Chapter 5 for
details on installing PCI add-on cards.
4. Make sure all power and data cables are properly connected and not blocking the chassis airflow. See Chapter 5 for details on cable connections. Also,
check the air seals for damage. The air seals are located under the blower
fan and beneath the frame cross section that separates the drive bay area
from the serverboard area of the chassis.
2-7
Checking the Drive Bay Setup
Next, you should check to make sure the hard drives have been properly installed
and all connections have been made.
Checking the Drives
1. For servicing the hard drives, you will need to remove the top chassis cover.
2. If you need to remove or install hard drives, please refer to Chapter 6.
Checking the Airflow
1. Airflow is provided by four counter-rotating fans. The system component
layout was carefully designed to direct sufficient cooling airflow to the components that generate the most heat.
2. Note that all power and data cables have been routed in such a way that they
do not block the airflow generated by the fans.
Providing Power
1. The last thing you must do is to provide input power to the system. Plug the
power cord from the power supply unit into a high-quality power strip that offers protection from electrical noise and power surges. It is recommended that
you use an uninterruptible power supply (UPS).
2. Turn on the power switch on the back of the power supply, then depress the
power button on the front chassis control panel.
2-12
Chapter 3: System Interface
Chapter 3
System Interface
3-1
Overview
There are several LEDs on the control panel to keep you constantly informed of the
overall status of the system as well as the three buttons described below.
3-2
Control Panel Buttons
There are three buttons located on the front of the chassis: a reset button, a power
on/off button and a UID button.
Reset
Use the reset button to reboot the system.
Power
This is the main power button, which is used to apply or turn off the main system
power. Turning off system power with this button removes the main power but keeps
standby power supplied to the system.
UID
Depressing the UID (unit identifier) button illuminates an LED on both the front
and rear of the chassis for easy system location in large stack configurations. The
LED will remain on until the button is pushed a second time. Another UID button
on the rear of the chassis serves the same function. See the table in Figure 3-1 for
descriptions of UID LED states.
3-1
SUPERSERVER 1026T-URF/1026T-UF User's Manual
3-3
Control Panel LEDs
The control panel located on the front of the SC113T chassis has five LEDs. These
LEDs provide you with critical information related to different parts of the system.
This section explains what each LED indicates when illuminated and any corrective
action you may need to take.
Universal Information LED
When this LED blinks red quickly, it indicates a fan failure and when blinking red
slowly a power failure. This LED will be blue when used for UID (Unit Identifier).
When on continuously it indicates an overheat condition, which may be caused by
cables obstructing the airflow in the system or the ambient room temperature being
too warm. Check the routing of the cables and make sure all fans are present and
operating normally. You should also check to make sure that the chassis covers
are installed. Finally, verify that the heatsinks are installed properly (see Chapter
5). This LED will remain flashing or on as long as the indicated condition exists.
See the table below for descriptions of the LED states.
Figure 3-1. Universal Information LED States
Universal Information LED States
State
Indication
Fast Blinking Red (1x/sec)
Fan Fail
Solid Red
CPU Overheat
Slow Blinking Red (1x/4 sec)
Power Fail
Solid Blue
Local UID Button Depressed
Blinking Blue
IPMI-Activated UID
Note: deactivating the UID LED must be performed in the same way it was activated.
(If the UID LED was activated via IPMI, you can only turn the LED off via IPMI and
not with the UID button.)
3-2
Chapter 3: System Interface
NIC2
Indicates network activity on LAN2 when flashing.
NIC1
Indicates network activity on LAN1 when flashing.
HDD
Indicates DVD-ROM/hard drive activity when flashing.
Power
Indicates power is being supplied to the system's power supply units. This LED
should normally be illuminated when the system is operating.
3-3
SUPERSERVER 1026T-URF/1026T-UF User's Manual
3-4
Hard Drive Carrier LEDs
Each hard drive carrier has two LEDs.
•
Green: When illuminated, the green LED on the front of the drive carrier indicates drive activity. A connection to the SATA backplane enables this LED to
blink on and off when that particular drive is being accessed.
•
Red: The red LED indicates two states. When blinking, it indicates the drive
is rebuilding. When solid, it indicates a drive failure. If a drive fails, you should
be notified by your system management software. Please refer to Chapter 6 for
instructions on replacing failed drives.
3-4
Chapter 4: Warning Statements for AC Systems
Chapter 4
Standardized Warning Statements for AC Systems
4-1
About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certified technicians should attempt to install or configure
components.
Read this appendix in its entirety before installing or configuring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.
Warning Definition
Warning!
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
警告の定義
この警告サインは危険を意味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、
電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前,必须充分
意识到触电的危险,并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。
此警告符號代表危險。
您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前,請注意觸
電的危險,並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。
4-1
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu
Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes
de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
final de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES.
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS.
‫תקנון הצהרות אזהרה‬
‫ על מנת להזהיר את המשתמש מפני חבלה‬,‫הצהרות הבאות הן אזהרות על פי תקני התעשייה‬
‫ יש ליצור קשר עם מחלקת תמיכה‬,‫ במידה ויש שאלות או היתקלות בבעיה כלשהי‬.‫פיזית אפשרית‬
.‫ טכנאים מוסמכים בלבד רשאים להתקין או להגדיר את הרכיבים‬.‫טכנית של סופרמיקרו‬
.‫יש לקרוא את הנספח במלואו לפני התקנת או הגדרת הרכיבים במארזי סופרמיקרו‬
4-2
Warning Statements for AC Systems
. ‫ﺗﺤﺬﻳﺮ!ﻫﺬﺍ ﺍﻟﺮﻣﺰ ﻳﻌﻨﻲ ﺧﻄﺮ ﺍﻧﻚ ﻓﻲ ﺣﺎﻟﺔ ﻳﻤﻜﻦ ﺃﻥ ﺗﺘﺴﺒﺐ ﻓﻲ ﺍﺻﺎﺑﺔ ﺟﺴﺪﻳﺔ‬
‫ﻛﻦ ﻋﻠﻰ ﻋﻠﻢ ﺑﺎﻟﻤﺨﺎﻁﺮ ﺍﻟﻨﺎﺟﻤﺔ ﻋﻦ ﺍﻟﺪﻭﺍﺋﺮ‬،‫ﻗﺒﻞ ﺃﻥ ﺗﻌﻤﻞ ﻋﻠﻰ ﺃﻱ ﻣﻌﺪﺍﺕ‬
‫ﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ‬
‫ﻭﻛﻦ ﻋﻠﻰ ﺩﺭﺍﻳﺔ ﺑﺎﻟﻤﻤﺎﺭﺳﺎﺕ ﺍﻟﻮﻗﺎﺋﻴﺔ ﻟﻤﻨﻊ ﻭﻗﻮﻉ ﺃﻱ ﺣﻮﺍﺩﺙ‬
‫ﺍﺳﺘﺨﺪﻡ ﺭﻗﻢ ﺍﻟﺒﻴﺎﻥ ﺍﻟﻤﻨﺼﻮﺹ ﻓﻲ ﻧﻬﺎﻳﺔ ﻛﻞ ﺗﺤﺬﻳﺮ ﻟﻠﻌﺜﻮﺭ ﺗﺮﺟﻤﺘﻬﺎ‬
안전을 위한 주의사항
경고!
이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준
작업절차를 준수해 주시기 바랍니다.
해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.
BEWAAR DEZE INSTRUCTIES
4-3
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Installation Instructions
Warning!
Read the installation instructions before connecting the system to the power source.
設置手順書
システムを電源に接続する前に、設置手順書をお読み下さい。
警告
将此系统连接电源前,请先阅读安装说明。
警告
將系統與電源連接前,請先閱讀安裝說明。
Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen
lesen.
¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.
Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives
d'installation.
.‫יש לקרוא את הוראות התקנה לפני חיבור המערכת למקור מתח‬
‫ﺍﻗﺮ ﺇﺭﺷﺎﺩﺍﺕ ﺍﻟﺘﺮﻛﻴﺐ ﻗﺒﻞ ﺗﻮﺻﻴﻞ ﺍﻟﻨﻈﺎﻡ ﺇﻟﻰ ﻣﺼﺪﺭ ﻟﻠﻄﺎﻗﺔ‬
시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.
Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron
aansluit.
4-4
Chapter 4: Warning Statements for AC Systems
Circuit Breaker
Warning!
This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.
サーキット・ブレーカー
この製品は、短絡(過電流)保護装置がある建物での設置を前提としています。
保護装置の定格が250 V、20 Aを超えないことを確認下さい。
警告
此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电
流不大于250V,20A。
警告
此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電
流不大於250V,20A。
Warnung
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschlussbzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.
¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)
del edificio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.
Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit
dépend de l'installation électrique du local. Vérifiez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A.
‫ יש לוודא כי‬.‫מוצר זה מסתמך על הגנה המותקנת במבנים למניעת קצר חשמלי‬
250 V, 20 A-‫המכשיר המגן מפני הקצר החשמלי הוא לא יותר מ‬
‫ﻫﺬﺍ ﺍﻟﻤﻨﺘﺞ ﻳﻌﺘﻤﺪ ﻋﻠﻰ ﻣﻌﺪﺍﺕ ﺍﻟﺤﻤﺎﻳﺔ ﻣﻦ ﺍﻟﺪﻭﺍﺋﺮﺍﻟﻘﺼﻴﺮﺓ ﺍﻟﺘﻲ ﺗﻢ ﺗﺜﺒﻴﺘﻬﺎ ﻓﻲ‬
‫ﺍﻟﻤﺒﻨﻰ‬
20A, 250V :‫ﺗﺄﻛﺪ ﻣﻦ ﺃﻥ ﺗﻘﻴﻴﻢ ﺍﻟﺠﻬﺎﺯ ﺍﻟﻮﻗﺎﺋﻲ ﻟﻴﺲ ﺃﻛﺜﺮ ﻣﻦ‬
4-5
SUPERSERVER 1026T-URF/1026T-UF User's Manual
경고!
이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에
의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지
않도록 해야 합니다.
Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van
uw electrische installatie. Controleer of het beveiligde aparaat niet groter
gedimensioneerd is dan 220V, 20A.
Power Disconnection Warning
Warning!
The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.
電源切断の警告
システムコンポーネントの取り付けまたは取り外しのために、
シャーシー内部にアクセス
するには、
システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り
外す必要があります。
警告
在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。
警告
在您打開機殼安裝或移除內部元件前,必須將系統完全斷電,並移除電源線。
Warnung
Das System muss von allen Quellen der Energie und vom Netzanschlusskabel
getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es
auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder
zu entfernen.
4-6
Chapter 4: Warning Statements for AC Systems
¡Advertencia!
El sistema debe ser disconnected de todas las fuentes de energía y del cable
eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso
el interior del chasis para instalar o para quitar componentes de sistema.
Attention
Le système doit être débranché de toutes les sources de puissance ainsi que de
son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour
installer ou enlever des composants de systéme.
‫אזהרה מפני ניתוק חשמלי‬
!‫אזהרה‬
‫יש לנתק את המערכת מכל מקורות החשמל ויש להסיר את כבל החשמלי מהספק‬
.‫לפני גישה לחלק הפנימי של המארז לצורך התקנת או הסרת רכיבים‬
‫ﻳﺠﺐ ﻓﺼﻞ ﺍﻟﻨﻈﺎﻡ ﻣﻦ ﺟﻤﻴﻊ ﻣﺼﺎﺩﺭ ﺍﻟﻄﺎﻗﺔ ﻭﺇﺯﺍﻟﺔ ﺳﻠﻚ ﺍﻟﻜﻬﺮﺑﺎء ﻣﻦ ﻭﺣﺪﺓ ﺍﻣﺪﺍﺩ‬
‫ﺍﻟﻄﺎﻗﺔ ﻗﺒﻞ‬
‫ﺍﻟﻮﺻﻮﻝ ﺇﻟﻰ ﺍﻟﻤﻨﺎﻁﻖ ﺍﻟﺪﺍﺧﻠﻴﺔ ﻟﻠﻬﻴﻜﻞ ﻟﺘﺜﺒﻴﺖ ﺃﻭ ﺇﺯﺍﻟﺔ ﻣﻜﻮﻧﺎﺕ ﺍﻟﺠﻬﺎﺯ‬
경고!
시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에
반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야
합니다.
Waarschuwing
Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren
of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle
stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen
4-7
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Equipment Installation
Warning!
Only trained and qualified personnel should be allowed to install, replace, or service
this equipment.
機器の設置
トレーニングを受け認定された人だけがこの装置の設置、交換、
またはサービスを許可
されています。
警告
只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。
警告
只有經過受訓且具資格人員才可安裝、更換與維修此設備。
Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,
qualifiziertem Personal gestattet werden.
¡Advertencia!
Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
Attention
Il est vivement recommandé de confier l'installation, le remplacement et la
maintenance de ces équipements à des personnels qualifiés et expérimentés.
!‫אזהרה‬
.‫ להחליף את הציוד או לתת שירות עבור הציוד‬,‫צוות מוסמך בלבד רשאי להתקין‬
‫ﻳﺠﺐ ﺃﻥ ﻳﺴﻤﺢ ﻓﻘﻂ ﻟﻠﻤﻮﻅﻔﻴﻦ ﺍﻟﻤﺆﻫﻠﻴﻦ ﻭﺍﻟﻤﺪﺭﺑﻴﻦ ﻟﺘﺮﻛﻴﺐ ﻭﺍﺳﺘﺒﺪﺍﻝ ﺃﻭ ﺧﺪﻣﺔ ﻫﺬﺍ ﺍﻟﺠﻬﺎﺯ‬
경고!
훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수
있습니다.
4-8
Chapter 4: Warning Statements for AC Systems
Waarschuwing
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door
geschoold en gekwalificeerd personeel.
Restricted Area
Warning!
This unit is intended for installation in restricted access areas. A restricted access
area can be accessed only through the use of a special tool, lock and key, or other
means of security. (This warning does not apply to workstations).
アクセス制限区域
このユニットは、
アクセス制限区域に設置されることを想定しています。
アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いての
み出入りが可能です。
警告
此部件应安装在限制进出的场所,限制进出的场所指只能通过使用特殊工具、锁和
钥匙或其它安全手段进出的场所。
警告
此裝置僅限安裝於進出管制區域,進出管制區域係指僅能以特殊工具、鎖頭及鑰匙
或其他安全方式才能進入的區域。
Warnung
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.
Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.
¡Advertencia!
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.
Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.
Attention
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une
zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme
de verrouillage et une clé, ou tout autre moyen de sécurité.
4-9
SUPERSERVER 1026T-URF/1026T-UF User's Manual
‫אזור עם גישה מוגבלת‬
!‫אזהרה‬
‫ הגישה ניתנת בעזרת‬.‫יש להתקין את היחידה באזורים שיש בהם הגבלת גישה‬
.('‫ מנעול וכד‬,‫כלי אבטחה בלבד )מפתח‬
. ‫ﺗﻢ ﺗﺨﺼﻴﺺ ﻫﺬﻩ ﺍﻟﻮﺣﺪﺓ ﻟﺘﺮﻛﻴﺒﻬﺎ ﻓﻲ ﻣﻨﺎﻁﻖ ﻣﺤﻈﻮﺭﺓ‬
،‫ﻳﻤﻜﻦ ﺍﻟﻮﺻﻮﻝ ﺇﻟﻰ ﻣﻨﻄﻘﺔ ﻣﺤﻈﻮﺭﺓ ﻓﻘﻂ ﻣﻦ ﺧﻼﻝ ﺍﺳﺘﺨﺪﺍﻡ ﺃﺩﺍﺓ ﺧﺎﺻﺔ‬
‫ﻗﻔﻞ ﻭﻣﻔﺘﺎﺡ ﺃﻭ ﺃﻱ ﻭﺳﻴﻠﺔ ﺃﺧﺮﻯ ﻟﻼﻷﻣﺎﻥ‬
경고!
이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및
키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.
Waarschuwing
Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.
Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te
maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.
Battery Handling
Warning!
There is the danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、
または同等のものを使用下さい。使用済電池は製造元の指示に従
って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。
4-10
Chapter 4: Warning Statements for AC Systems
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer
que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.
¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.
!‫אזהרה‬
‫ יש להחליף‬.‫קיימת סכנת פיצוץ של הסוללה במידה והוחלפה בדרך לא תקינה‬
.‫את הסוללה בסוג התואם מחברת יצרן מומלצת‬
.‫סילוק הסוללות המשומשות יש לבצע לפי הוראות היצרן‬
‫ﻫﻨﺎﻙ ﺧﻄﺮ ﻣﻦ ﺍﻧﻔﺠﺎﺭ ﻓﻲ ﺣﺎﻟﺔ ﺍﺳﺘﺒﺪﺍﻝ ﺍﻟﺒﻄﺎﺭﻳﺔ ﺑﻄﺮﻳﻘﺔ ﻏﻴﺮ ﺻﺤﻴﺤﺔ ﻓﻌﻠﻴﻚ‬
‫ﺍﺳﺘﺒﺪﺍﻝ ﺍﻟﺒﻄﺎﺭﻳﺔ‬
‫ﻓﻘﻂ ﺑﻨﻔﺲ ﺍﻟﻨﻮﻉ ﺃﻭ ﻣﺎ ﻳﻌﺎﺩﻟﻬﺎ ﻛﻤﺎ ﺃﻭﺻﺖ ﺑﻪ ﺍﻟﺸﺮﻛﺔ ﺍﻟﻤﺼﻨﻌﺔ‬
‫ﺗﺨﻠﺺ ﻣﻦ ﺍﻟﺒﻄﺎﺭﻳﺎﺕ ﺍﻟﻤﺴﺘﻌﻤﻠﺔ ﻭﻓﻘﺎ ﻟﺘﻌﻠﻴﻤﺎﺕ ﺍﻟﺸﺮﻛﺔ ﺍﻟﺼﺎﻧﻌﺔ‬
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Waarschuwing
Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.
4-11
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Redundant Power Supplies
Warning!
This unit might have more than one power supply connection. All connections must
be removed to de-energize the unit.
冗長電源装置
このユニットは複数の電源装置が接続されている場合があります。
ユニットの電源を切るためには、すべての接続を取り外さなければなりません。
警告
此部件连接的电源可能不止一个,必须将所有电源断开才能停止给该部件供电。
警告
此裝置連接的電源可能不只一個,必須切斷所有電源才能停止對該裝置的供電。
Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass
der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.
¡Advertencia!
Puede que esta unidad tenga más de una conexión para fuentes de alimentación.
Para cortar por completo el suministro de energía, deben desconectarse todas las
conexiones.
Attention
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute
tension et tout courant électrique de l'unité, toutes les connexions d'alimentation
doivent être débranchées.
‫אם קיים יותר מספק אחד‬
!‫אזהרה‬
‫ יש להסיר את כל החיבורים על מנת לרוקן‬.‫ליחדה יש יותר מחיבור אחד של ספק‬
.‫את היחידה‬
4-12
Chapter 4: Warning Statements for AC Systems
.‫ﻗﺪ ﻳﻜﻮﻥ ﻟﻬﺬﺍ ﺍﻟﺠﻬﺎﺯ ﻋﺪﺓ ﺍﺗﺼﺎﻻﺕ ﺑﻮﺣﺪﺍﺕ ﺍﻣﺪﺍﺩ ﺍﻟﻄﺎﻗﺔ‬
‫ﻳﺠﺐ ﺇﺯﺍﻟﺔ ﻛﺎﻓﺔ ﺍﻻﺗﺼﺎﻻﺕ ﻟﻌﺰﻝ ﺍﻟﻮﺣﺪﺓ ﻋﻦ ﺍﻟﻜﻬﺮﺑﺎء‬
경고!
이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에
전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.
Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle
aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.
Backplane Voltage
Warning!
Hazardous voltage or energy is present on the backplane when the system is
operating. Use caution when servicing.
バックプレーンの電圧
システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。
修理する際には注意ください。
警告
当系统正在进行时,背板上有很危险的电压或能量,进行维修时务必小心。
警告
當系統正在進行時,背板上有危險的電壓或能量,進行維修時務必小心。
Warnung
Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche
Spannungen oder Energien auf. Vorsicht bei der Wartung.
¡Advertencia!
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.
Tenga cuidado cuando lo revise.
Attention
Lorsque le système est en fonctionnement, des tensions électriques circulent sur
le fond de panier. Prendre des précautions lors de la maintenance.
4-13
SUPERSERVER 1026T-URF/1026T-UF User's Manual
‫מתח בפנל האחורי‬
!‫אזהרה‬
‫ יש להיזהר במהלך‬.‫קיימת סכנת מתח בפנל האחורי בזמן תפעול המערכת‬
.‫העבודה‬
‫ﻫﻨﺎﻙ ﺧﻄﺮ ﻣﻦ ﺍﻟﺘﻴﺎﺭ ﺍﻟﻜﻬﺮﺑﺎﺋﻲ ﺃﻭﺍﻟﻄﺎﻗﺔ ﺍﻟﻤﻮﺟﻮﺩﺓ ﻋﻠﻰ ﺍﻟﻠﻮﺣﺔ‬
‫ﻋﻨﺪﻣﺎ ﻳﻜﻮﻥ ﺍﻟﻨﻈﺎﻡ ﻳﻌﻤﻞ ﻛﻦ ﺣﺬﺭﺍ ﻋﻨﺪ ﺧﺪﻣﺔ ﻫﺬﺍ ﺍﻟﺠﻬﺎﺯ‬
경고!
시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생
합니다. 서비스 작업 시 주의하십시오.
Waarschuwing
Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het
systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.
Comply with Local and National Electrical Codes
Warning!
Installation of the equipment must comply with local and national electrical codes.
地方および国の電気規格に準拠
機器の取り付けはその地方および国の電気規格に準拠する必要があります。
警告
设备安装必须符合本地与本国电气法规。
警告
設備安裝必須符合本地與本國電氣法規。
Warnung
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.
¡Advertencia!
La instalacion del equipo debe cumplir con las normas de electricidad locales y
nacionales.
4-14
Chapter 4: Warning Statements for AC Systems
Attention
L'équipement doit être installé conformément aux normes électriques nationales
et locales.
‫תיאום חוקי החשמל הארצי‬
!‫אזהרה‬
.‫התקנת הציוד חייבת להיות תואמת לחוקי החשמל המקומיים והארציים‬
‫ﺗﺮﻛﻴﺐ ﺍﻟﻤﻌﺪﺍﺕ ﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﻳﺠﺐ ﺃﻥ ﻳﻤﺘﺜﻞ ﻟﻠﻘﻮﺍﻧﻴﻦ ﺍﻟﻤﺤﻠﻴﺔ ﻭﺍﻟﻮﻁﻨﻴﺔ ﺍﻟﻤﺘﻌﻠﻘﺔ‬
‫ﺑﺎﻟﻜﻬﺮﺑﺎء‬
경고!
현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.
Waarschuwing
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale
elektriciteitsvoorschriften.
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
製品の廃棄
この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen
des Landes erfolgen.
4-15
SUPERSERVER 1026T-URF/1026T-UF User's Manual
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y
reglamentos nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.
‫סילוק המוצר‬
!‫אזהרה‬
.‫סילוק סופי של מוצר זה חייב להיות בהתאם להנחיות וחוקי המדינה‬
‫ﻋﻨﺪ ﺍﻟﺘﺨﻠﺺ ﺍﻟﻨﻬﺎﺋﻲ ﻣﻦ ﻫﺬﺍ ﺍﻟﻤﻨﺘﺞ ﻳﻨﺒﻐﻲ ﺍﻟﺘﻌﺎﻣﻞ ﻣﻌﻪ ﻭﻓﻘﺎ ﻟﺠﻤﻴﻊ ﺍﻟﻘﻮﺍﻧﻴﻦ ﻭﺍﻟﻠﻮﺍﺋﺢ ﺍﻟﻮﻁﻨﻴﺔ‬
경고!
이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.
Hot Swap Fan Warning
Warning!
The fans might still be turning when you remove the fan assembly from the chassis.
Keep fingers, screwdrivers, and other objects away from the openings in the fan
assembly's housing.
ファン・ホットスワップの警告
シャーシから冷却ファン装置を取り外した際、
ファンがまだ回転している可能性がありま
す。ファンの開口部に、指、
ドライバー、およびその他のものを近づけないで下さい。
警告
当您从机架移除风扇装置,风扇可能仍在转动。小心不要将手指、螺丝起子和其他
物品太靠近风扇
4-16
Chapter 4: Warning Statements for AC Systems
警告
當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他
物品太靠近風扇。
Warnung
Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis
genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände
von den Öffnungen des Lüftergehäuses entfernt.
¡Advertencia!
Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador
del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de
las aberturas del ventilador
Attention
Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez
le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres
objets soient éloignés du logement du bloc ventilateur.
!‫אזהרה‬
‫ יש‬.‫ יתכן והמאווררים עדיין עובדים‬,‫כאשר מסירים את חלקי המאוורר מהמארז‬
‫להרחיק למרחק בטוח את האצבעות וכלי עבודה שונים מהפתחים בתוך המאוורר‬
‫ﻣﻦ ﺍﻟﻤﻤﻜﻦ ﺃﻥ ﺍﻟﻤﺮﺍﻭﺡ ﻻ ﺗﺰﺍﻝ ﺗﺪﻭﺭﻋﻨﺪ ﺇﺯﺍﻟﺔ ﻛﺘﻠﺔ ﺍﻟﻤﺮﻭﺣﺔ ﻣﻦ ﺍﻟﻬﻴﻜﻞ ﻳﺠﺐ ﺇﺑﻘﺎء‬
‫ﺍﻷﺻﺎﺑﻊ ﻭﻣﻔﻜﺎﺕ ﺍﻟﺒﺮﺍﻏﻲ‬
.‫ﻭﻏﻴﺮﻫﺎ ﻣﻦ ﺍﻷﺷﻴﺎء ﺑﻌﻴﺪﺍ ﻋﻦ ﺍﻟﻔﺘﺤﺎﺕ ﻓﻲ ﻛﺘﻠﺔ ﺍﻟﻤﺮﻭﺣﺔ‬
경고!
섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬
조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이
가까이 하지 않도록 배치해 주십시오.
Waarschuwing
Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het
ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers
en eventuele andere voorwerpen uit de buurt van de openingen in de
ventilatorbehuizing.
4-17
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Power Cable and AC Adapter
Warning!
When installing the product, use the provided or designated connection cables,
power cables and AC adaptors. Using any other cables and adaptors could cause
a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the
use of UL or CSA -certified cables (that have UL/CSA shown on the code) for any
other electrical devices than products designated by Supermicro only.
電源コードとACアダプター
製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター
を使用下さい。他のケーブルやアダプタを使用すると故障や火災の原因になることがあ
ります。電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表
記)を Supermicroが指定する製品以外に使用することを禁止しています。
警告
安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线
材或适配器可能会引起故障或火灾。除了Supermicro所指定的产品,电气用品和材
料安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。
警告
安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線
材或適配器可能會引起故障或火災。除了Supermicro所指定的產品,電氣用品和材
料安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。
Warnung
Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt
Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter
kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und
Material Safety Law verbietet die Verwendung von UL-oder CSA-zertifizierte Kabel,
UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von
Supermicro nur bezeichnet gezeigt haben.
¡Advertencia!
Al instalar el producto, utilice los cables de conexión previstos o designados, los
cables y adaptadores de CA. La utilización de otros cables y adaptadores podría
ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de
Seguridad del Material prohíbe el uso de UL o CSA cables certificados que tienen
UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos
designados por Supermicro solamente.
4-18
Chapter 4: Warning Statements for AC Systems
Attention
Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.
L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement
ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit
l'utilisation de UL ou CSA câbles certifiés qui ont UL ou CSA indiqué sur le code
pour tous les autres appareils électriques que les produits désignés par Supermicro
seulement.
AC
‫חשמליים ומתאמי‬
!‫אזהרה‬
‫ אשר‬AC ‫ ספקים ומתאמים‬,‫ יש להשתמש בכבלים‬,‫כאשר מתקינים את המוצר‬
‫ שימוש בכל כבל או מתאם אחר יכול לגרום לתקלה או‬.‫נועדו וסופקו לשם כך‬
‫ קיים איסור‬,‫ על פי חוקי שימוש במכשירי חשמל וחוקי בטיחות‬.‫קצר חשמלי‬
‫ )כשאר מופיע עליהם קוד של‬CSA -‫ או ב‬UL -‫להשתמש בכבלים המוסמכים ב‬
.‫( עבור כל מוצר חשמלי אחר שלא צוין על ידי סופרקמיקרו בלבד‬UL/CSA
‫ﻭﺍﻟﻜﺎﺑﻼﺕ ﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ‬،‫ﻋﻨﺪ ﺗﺮﻛﻴﺐ ﺍﻟﺠﻬﺎﺯ ﻳﺠﺐ ﺍﺳﺘﺨﺪﺍﻡ ﻛﺎﺑﻼﺕ ﺍﻟﺘﻮﺻﻴﻞ‬
‫ﻭﻣﺤﻮﻻﺕ ﺍﻟﺘﻴﺎﺭ ﺍﻟﻤﺘﺮﺩﺩ‬
.‫ ﺃﻥ ﺍﺳﺘﺨﺪﺍﻡ ﺃﻱ ﻛﺎﺑﻼﺕ ﻭﻣﺤﻮﻻﺕ ﺃﺧﺮﻯ ﻳﺘﺴﺒﺐ ﻓﻲ ﺣﺪﻭﺙ ﻋﻄﻞ ﺃﻭ ﺣﺮﻳﻖ‬. ‫ﺍﻟﺘﻲ‬
‫ﺗﻢ ﺗﻮﻓﻴﺮﻫﺎ ﻟﻚ ﻣﻊ ﺍﻟﻤﻨﺘﺞ‬
UL ‫ ﺃﻭ‬CSA ‫ﺍﻷﺟﻬﺰﺓ ﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ ﻭﻣﻮﺍﺩ ﻗﺎﻧﻮﻥ ﺍﻟﺴﻼﻣﺔ ﻳﺤﻈﺮ ﺍﺳﺘﺨﺪﺍﻡ ﺍﻟﻜﺎﺑﻼﺕ‬
‫ﻣﻌﺘﻤﺪﺓ ﻣﻦ ﻗﺒﻞ‬
Supermicro ‫ﻷﻱ ﺃﺟﻬﺰﺓ ﻛﻬﺮﺑﺎﺋﻴﺔ ﺃﺧﺮﻯ ﻏﻴﺮ ﺍﻟﻤﻨﺘﺠﺎﺕ ﺍﻟﻤﻌﻴﻨﺔ ﻣﻦ ﻗﺒﻞ‬
(UL/CSA ‫)ﺍﻟﺘﻲ ﺗﺤﻤﻞ ﻋﻼﻣﺔ‬
경고!
제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를
사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이
될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety
Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을
위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을
금지합니다.
Waarschuwing
Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,
stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden
tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet
verbiedt het gebruik van UL of CSA gecertificeerde kabels die UL of CSA die op
de code voor andere elektrische apparaten dan de producten die door Supermicro
alleen.
4-19
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Notes
4-20
Chapter 5: Advanced Serverboard Setup
Chapter 5
Advanced Serverboard Setup
This chapter covers the steps required to install processors and heatsinks to the
X8DTU-F serverboard, connect the data and power cables and install add-on
cards. All serverboard jumpers and connections are described and a layout and
quick reference chart are included in this chapter. Remember to close the chassis completely when you have finished working on the serverboard to protect and
cool the system sufficiently.
5-1
Handling the Serverboard
Static electrical discharge can damage electronic components. To prevent damage
to printed circuit boards, it is important to handle them very carefully (see Chapter 4).
Also note that the size and weight of the serverboard can cause it to bend if handled
improperly, which may result in damage. To prevent the serverboard from bending,
keep one hand under the center of the board to support it when handling.
The following measures are generally sufficient to protect your equipment from
static discharge.
Precautions
•
•
•
•
•
Use a grounded wrist strap designed to prevent static discharge.
Touch a grounded metal object before removing any board from its antistatic
bag.
Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or gold contacts.
When handling chips or modules, avoid touching their pins.
Put the serverboard, add-on cards and peripherals back into their antistatic
bags when not in use.
Unpacking
The serverboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.
5-1
SUPERSERVER 1026T-URF/1026T-UF User's Manual
5-2
Processor and Heatsink Installation
Warning! When handling the processor, avoid placing direct pressure on the label
area of the fan. Also, do not place the serverboard on a conductive surface, which can
damage the BIOS battery and prevent the system from booting up.
•
Always connect the power cord last and always remove it before adding, removing or changing any hardware components. Make sure that you install the
processor into the CPU socket before you install the CPU heatsink.
•
If you buy a CPU separately, make sure that you use an Intel-certified multidirectional heatsink only.
•
•
•
Make sure to install the serverboard into the chassis before you install the CPU
heatsinks.
When receiving a serverboard without a processor pre-installed, make sure that
the plastic CPU socket cap is in place and none of the socket pins are bent;
otherwise, contact your retailer immediately.
Refer to the Supermicro web site for updates on CPU support.
Installing LGA1366 Processors
1. Starting with CPU1, press the
socket clip to release the load
plate, which covers the CPU
socket, from its locked position.
2. Gently lift the socket clip to open
the load plate.
Socket Clip
Load Plate
3. Hold the plastic cap at its north
and south center edges to remove
it from the CPU socket.
Plastic Cap
Note: The photos on this page and
succeeding pages are for illustration
purposes only. They do not necessarily
reflect the exact product(s) described
in this manual.
Holding the north & south edges
5-2
Chapter 5: Advanced Serverboard Setup
CPU
1. After removing the plastic cap, use
your thumb and the index finger
to hold the CPU at the north and
south center edges.
2. Align the CPU key (the semi-circle
cutout) with the socket key (the
notch below the gold color dot on
the side of the socket).
CPU Socket
3. Once the CPU and the socket are
aligned, carefully lower the CPU
straight down into the socket.
Do not rub the CPU against the
surface of the socket or its pins to
avoid damaging the CPU or the
socket.
CPU
Align CPU keys with socket keys.
4. With the CPU in the socket, inspect the four corners of the CPU
to make sure that it sits level and
is properly installed.
5. Once the CPU is securely seated
in the socket, lower the CPU load
plate to the socket.
6. Use your thumb to gently push the
socket clip down to the clip lock.
7. Repeat for the CPU2 socket for a
dual-processor configuration.
Important! Please save the plastic
cap. The serverboard must be shipped
with the plastic cap properly installed to
protect the CPU socket pins. Shipment
without the plastic cap properly installed
may cause damage to the socket pins.
5-3
Load Plate
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Installing the Heatsink
1. Place the heatsink on top of the
CPU so that the four mounting
holes are aligned with those on the
retention mechanism.
2. Remove the thin layer of protective
film from the copper core of the
heatsink.
Warning: The CPU may overheat if the
protective film is not removed from the
heatsink.
3. Apply the proper amount of thermal grease on the CPU. If your
heatsink came with a thermal pad,
please ignore this step.
Screw #1
Screw #3
Screw #4
Screw #2
4. Screw in two diagonal screws (i.e.
the #1 and the #2 screws) until
just snug (do not over-tighten the
screws, which may damage the
CPU.)
5. Finish the installation by fully tightening all four screws.
5-4
Chapter 5: Advanced Serverboard Setup
Removing the Heatsink
Warning: We do not recommend removing the CPU or the heatsink. If you do need
to remove the heatsink, please follow the instructions below to prevent damage to the
CPU or other components.
1. Unplug the power cord from the power supply.
1. Unscrew and remove the heatsink screws in the
sequence shown in the picture below.
2. Hold the heatsink and gently wiggle it to loosen it
from the CPU. (Do not use excessive force when
doing this!)
3. Once the heatsink is loosened, remove it from
the CPU.
4. Clean the surface of the CPU and the heatsink
to get rid of the old thermal grease. Reapply the
proper amount of thermal grease before you reinstall the heatsink.
Screw #1
Screw #3
Screw #4
Screw #2
5-5
SUPERSERVER 1026T-URF/1026T-UF User's Manual
5-3
Connecting Cables
Now that the processors are installed, the next step is to connect the cables to the
serverboard. These include the data (ribbon) cables for the peripherals and control
panel and the power cables.
Connecting Data Cables
The cables used to transfer data from the peripheral devices have been carefully
routed in preconfigured systems to prevent them from blocking the flow of cooling
air that moves through the system from front to back. If you need to disconnect any
of these cables, you should take care to reroute them as they were originally after
reconnecting them (make sure the red wires connect to the pin 1 locations). If you
are configuring the system, keep the airflow in mind when routing the cables.
The following data cables (with their serverboard connector locations noted) should
be connected. See the serverboard layout diagram in this chapter for connector
locations.
•
DVD-ROM drive cable (SATA4)
•
SATA cables (SATA0 ~ SATA3)
•
Control Panel cable (JF1, see next page)
Connecting Power Cables
The X8DTU-F has a 20-pin primary power supply connector designated "JPW1"
for connection to the ATX power supply. Connect the appropriate connector from
the power supply to JPW1 to supply power to the serverboard. See the Connector
Definitions section in this chapter for power connector pin definitions.
In addition, your power supply must be connected to the 8-pin Processor Power
connectors at JPW2 and JPW3.
Connecting the Control Panel
JF1 contains header pins for various front control panel connectors. See Figure
5-1 for the pin locations of the various front control panel buttons and LED indicators. Please note that even and odd numbered pins are on opposite sides of each
header.
All JF1 wires have been bundled into single keyed ribbon cable to simplify their
connection. The red wire in the ribbon cable plugs into pin 1 of JF1. Connect the
other end of the cable to the Control Panel printed circuit board, located just behind
the system status LEDs in the chassis.
5-6
Chapter 5: Advanced Serverboard Setup
See the Connector Definitions section in this chapter for details and pin descriptions of JF1.
Figure 5-1. Front Control Panel Header Pins (JF1)
20
19
Ground
NMI
x (key)
x (key)
Power LED
Vcc
HDD LED
UID Switch/Vcc
NIC1
Vcc
NIC2
Vcc
OH/Fan Fail/UID LED
Vcc
Power Fail LED
Vcc
Ground
Reset
Ground
Power
2
5-4
1
I/O Ports
The I/O ports are color coded in conformance with the PC 99 specification. See
Figure 5-2 below for the colors and locations of the various I/O ports.
Figure 5-2. Rear Panel I/O Ports
2
1
5
4
6
7
3
Rear I/O Ports
1. Keyboard
6. COM1
2. PS/2 Mouse
7. VGA Port
3. USB0
8. LAN1
4. USB1
9. LAN2
5. IPMI LAN
10. UID Button
5-7
8
9
10
SUPERSERVER 1026T-URF/1026T-UF User's Manual
5-5
Installing Memory
Note: Check the Supermicro web site for recommended memory modules.
CAUTION
Exercise extreme care when installing or removing DIMM modules
to prevent any possible damage.
Installing DIMMs
1. Insert the desired number of DIMMs into the memory slots, starting with slot
P1-DIMM1A. For best performance, install memory modules of the same type
and same speed in the slots as indicated in the tables below.
2. Insert each DIMM vertically into its slot. Pay attention to the notch along the
bottom of the module to prevent inserting the DIMM module incorrectly (see
Figure 5-5).
3. Gently press down on the DIMM module until it snaps into place in the slot.
Repeat for all modules
Memory Support
The X8DTU-F supports up to 96 GB of registered ECC DDR3-1333/1066/800
SDRAM in 12 slots. (RDIMM modules are supported.)
Notes: Memory speed support depends on the type of CPU used. Due to OS limitations, some operating systems may not show more than 4 GB of memory. Due to
Memory Population for Optimal Performance With One CPU (CPU1) Installed
Branch 0
3 DIMMs
P1 DIMM1A
6 DIMMs
P1 DIMM1A
Branch 1
Branch 2
P1 DIMM2A
P1 DIMM1B
P1 DIMM2A
P1 DIMM3A
P1 DIMM2B
P1 DIMM3A
P1 DIMM3B
Memory Population for Optimal Performance With One CPU (CPU2) Installed
Branch 0
3 DIMMs
P2 DIMM1A
6 DIMMs
P2 DIMM1A
Branch 1
Branch 2
P2 DIMM2A
P2 DIMM1B
P2 DIMM2A
P2 DIMM3A
P2 DIMM2B
P2 DIMM3A
P2 DIMM3B
Memory Population for Optimal Performance With Two CPUs Installed
CPU1
Branch 0
6 DIMMs
1A
12
DIMMs
1A
Branch 1
2A
1B
2A
CPU2
Branch 3
3A
2B
3A
Branch 0
1A
3B
5-8
1A
Branch 1
2A
1B
2A
Branch 3
3A
2B
3A
3B
Chapter 5: Advanced Serverboard Setup
memory allocation to system devices, memory remaining available for operational
use will be reduced when 4 GB of RAM is used. The reduction in memory availability
is disproportional. (Refer to the Memory Availability Table below for details.)
Possible System Memory Allocation & Availability
System Device
Size
Physical Memory Remaining
(4 GB Total System
Memory)
Firmware Hub flash memory (System BIOS)
1 MB
3.99
Local APIC
4 KB
3.99
Area Reserved for the chipset
2 MB
3.99
I/O APIC (4 Kbytes)
4 KB
3.99
PCI Enumeration Area 1
256 MB
3.76
PCI Express (256 MB)
256 MB
3.51
PCI Enumeration Area 2 (if needed) -Aligned on 256-MB boundary-
512 MB
3.01
VGA Memory
16 MB
2.85
TSEG
1 MB
2.84
Memory available to System BIOS & OS applications
2.84
DIMM Population Table
DIMM
Slots per
Channel
DIMMs
Populated
per Channel
DIMM Type (Reg.=
Registered)
Speeds (in MHz)
Ranks per DIMM
(any combination;
SR=Single Rank,
DR=Dual Rank,
QR=Quad Rank)
2
1
Reg. DDR3 ECC
800,1066,1333
SR or DR
2
1
Reg. DDR3 ECC
800,1066
QR
2
2
Reg. DDR3 ECC
800,1066
Mixing SR, DR
2
2
Reg. DDR3 ECC
800
Mixing SR, DR,QR
Figure 5-3. Installing DIMM into Slot
Notch
Notch
To Install: Insert module
vertically and press
down until it snaps into
place. Pay attention to
the alignment notch at
the bottom.
To Remove:
Use your thumbs to
gently push the release
tabs near both ends of
the module. This should
release it from the slot.
Front View
Note: Notch should align
with the receptive key
point on the slot.
Release Tab
Top View of DDR3 Slot
5-9
Release Tab
SUPERSERVER 1026T-URF/1026T-UF User's Manual
5-6
Adding PCI Cards
PCI Expansion Slots
Riser cards are used to support add-on cards to the system. See the tables below
for the expansion cards that may be used in the SC113TQ-R650U/SC113TQ-560U
chassis.
PCI Card Installation
Before installing a PCI add-on card, make sure you install it into the correct riser
card. Begin by releasing the locking tab that corresponds to the slot you wish to
populate. Insert the expansion card into the correct riser card, pushing down with
your thumbs evenly on both sides of the card.
PCI Slot/Card Configurations
Left Side Riser Card
Expansion Card Supported
RSC-R1UU-UE16 (pre-installed)
1x UIO card and 1x PCI-E x16 card
RSC-R1UU-E8PR (optional)
AOC-PG-i2+ for 2x LAN ports
5-10
Chapter 5: Advanced Serverboard Setup
5-7
Serverboard Details
Figure 5-4. SUPER X8DTU-F Layout
(not drawn to scale)
Fan8
(CPU2)
P2-DIMM3A
JPW2
JPW3
P2-DIMM3B
KB /MS
JPW1
USB 0/1
IPMI LAN
P2-DIMM2A
P2-DIMM2B
JPI2C
P2-DIMM1A
CPU1
COM1
P2-DIMM1B
Fan1
VGA
Fan2
Battery
X8DTU-F
CPU2
Fan7
(CPU1)
Speaker
Fan3
LAN1
P1-DIMM1B
P1-DIMM1A
LAN2
P1-DIMM2B
P1-DIMM2A
LAN CTRL
JD1
UID
Button
P1-DIMM3B
LE2
P1-DIMM3A
JPL1
I-SATA4
Fan4
I-SATA5
I-SATA2
SXB3: PCI Express 2.0 x8 (x4 slot)
I-SATA3
SXB1: PCI Express 2.0 x16
I-SATA0
UIOP
I-SATA1
SXB2: PCI-E 2.0 x 8
JF1
LE1
Intel
I5520
JP3 JOH1
(North Bridge)
T-SGPIO2
CPLD
JPB
T-SGPIO1
J17
JPRST1
JWD
Intel
JPG1
ICH10R
(South Bridge)
BMC CTRL
BIOS
USB2/3
JLPC1
JBT1
JP5
COM2
Fan6
IPMB JI2C1
USB4/5
USB6
USB7
Fan5
JL1
JI2C2
Notes:
Jumpers not indicated are for test purposes only.
When LE1 LED is on, the onboard power connection is on. Make sure to unplug
the power cables before removing or installing components.
IPMI (Intelligent Platform Management Interface) 2.0 is supported by the X8DTU-F.
For more information on IPMI configuration, refer to the Embedded BMC IPMI User
Guide @http://www.supermicro.com/support/manuals/.
Warning
To provide adequate power to the add-on cards installed on the serverboard,
please connect the UIOP PWR connector to the power supply for these cards to
work properly.
5-11
SUPERSERVER 1026T-URF/1026T-UF User's Manual
X8DTU-F Quick Reference
Jumper
Description
Default Setting
JBT1
CMOS Clear
(See Section 5-9)
JI2C1/JI2C2
SMB to PCI-Exp. Slots
Open (Disabled)
JP3
ME Mode Select
Open (Normal)
JP5
ME Recovery
Open (Normal)
JPG1
VGA Enable/Disable
Pins 1-2 (Enabled)
JPL1
LAN1/2 Enable/Disable
Pins 1-2 (Enabled)
JPRST1
BMC/PHY Reset Enable/Disable
Open (Normal)
JWD1
Watch Dog
Pins 1-2 (Reset)
Connector
Description
COM1/COM2
Serial Port/Header
FAN 1-8
Chassis/CPU Fan Headers
Floppy
Floppy Disk Drive Connector
IPMB
IPMB I2C Header (for an IPMI Card)
I-SATA0 ~ I-SATA5
SATA Ports
JD1
Onboard Speaker/Power LED
JF1
Control Panel Connector
JL1
Chassis Intrusion Header
JOH1
Overheat Warning Header
2
JPI C
Power Supply SMBus I2C Header
JPW1
20-Pin ATX Power Connector
JPW2/JPW3
8-pin Processor Power Connectors
LAN1/2
Gigabit Ethernet (RJ45) Ports
IPMI_LAN
IPMI 2.0 Dedicated LAN
T-SGPIO-1/T-SGPIO-2
Serial General Purpose Input/Output Headers
UIOP
UIO Card Power Supply Header
USB0/1, USB6, USB7
Universal Serial Bus (USB) Ports
USB2/3, USB4/5
Universal Serial Bus (USB) Headers
LED
Description
LE1
Onboard Standby PWR warning LED Indicator
LE2
Unit Identification (UID) LED
5-12
Chapter 5: Advanced Serverboard Setup
5-8
Connector Definitions
ATX Power 20-pin Connector
Pin Definitions (JPW1)
Pin# Definition Pin #
Definition
11
PS On
1
Ground
12
5VSB
2
Ground
fication. Make sure that the orientation
of the connector is correct. See the
13
Ground
3
Ground
14
Ground
4
Ground
table on the right for pin definitions.
15
Ground
5
Ground
16
NC2
6
NC1
17
12V
7
12V
18
12V
8
12V
19
12V
9
12V
20
12V
10
12V
ATX Power Connector
The primary ATX power supply connector meets the SSI EPS 12V speci-
Processor Power Connectors
JPW2 and JPW3 must also be connected to the power supply to provide
power for the processor(s). See the
table on the right for pin definitions.
Processor Power
Pin Definitions (JPW2/JPW3)
Pins
Definition
1 through 4
Ground
5 through 8
+12V
Warning: To prevent damage to your power supply or serverboard, please use a power
supply that contains a 20-pin and two 8-pin power connectors. Be sure to connect
these power connectors to the 20-pin and the two 8-pin power connectors on your
serverboard for adequate power supply to your system. Failure to do so will void the
manufacturer warranty on your power supply and serverboard.
NMI Button
The non-maskable interrupt button
header is located on pins 19 and 20
of JF1. Refer to the table on the right
for pin definitions.
NMI Button
Pin Definitions (JF1)
Pin#
Definition
19
Control
20
Ground
Power LED
Pin Definitions (JF1)
Power LED
The Power LED connection is located
on pins 15 and 16 of JF1. Refer to the
table on the right for pin definitions.
5-13
Pin#
Definition
15
Vcc
16
Control
SUPERSERVER 1026T-URF/1026T-UF User's Manual
HDD LED
The HDD (IDE Hard Disk Drive) LED
connection is located on pins 13 and
HDD LED
Pin Definitions (JF1)
Pin#
Definition
LED cable to display disk activity.
13
Vcc
Refer to the table on the right for pin
definitions.
14
HD Active
14 of JF1. Attach the IDE hard drive
NIC1 LED
The NIC1 (Network Interface Controller) LED connection is located on pins
11 and 12 of JF1. Attach the NIC1
LED cable to display network activity.
Refer to the table on the right for pin
definitions.
NIC1 LED
Pin Definitions (JF1)
Pin#
Definition
11
Vcc
12
Ground
NIC2 LED
The NIC2 (Network Interface Controller) LED connection is located on
pins 9 and 10 of JF1. Attach the NIC2
LED cable to display network activity.
Refer to the table on the right for pin
definitions.
NIC2 LED
Pin Definitions (JF1)
Pin#
Definition
9
Vcc
10
Ground
Universal Info. LED
Pin Definitions (JF1)
Overheat (OH)/Fan Fail/PWR Fail/
UID LED
Connect an LED to pins 7 and 8 of
JF1 to provide advanced warning of
chassis overheating or fan failure.
These pins also work with the front
UID indicator, which will activate as
either a solid or flashing blue LED
depending on whether the LED was
activated via IPMI or the UID button.
Refer to the tables on the right for pin
definitions and status indicators.
5-14
Pin#
Definition
7
Vcc
8
Control
Red LED Indications
State
Indication
Solid
Overheat
Blinking (fast)
Fan Fail
Blinking (slow)
Power Fail
Blue LED Indications
State
Indication
Solid
UID (via Button)
Blinking
UID (via IPMI)
Chapter 5: Advanced Serverboard Setup
Power Fail LED
Power Fail LED
Pin Definitions (JF1)
The Power Fail LED connection is
located on pins 5 and 6 of JF1. Refer
Pin#
Definition
to the table on the right for pin defini-
5
Vcc
tions.
6
Ground
Reset Button
Reset Button
Pin Definitions (JF1)
The Reset Button connection is located on pins 3 and 4 of JF1. Attach
it to the hardware reset switch on the
computer case. Refer to the table on
the right for pin definitions.
Pin#
Definition
3
Reset
4
Ground
Power Button
The Power Button connection is
located on pins 1 and 2 of JF1. Momentarily contacting both pins will
power on/off the system. This button
can also be configured to function
as a suspend button (see the Power
Button Mode setting in BIOS). To turn
off the power when set to suspend
mode, depress the button for at least
4 seconds. Refer to the table on the
right for pin definitions.
Power Button
Pin Definitions (JF1)
Pin#
Definition
1
PW_ON
2
Ground
Universal Serial Bus Ports
Pin Definitions (USB0/1, USB6/7)
Universal Serial Bus Ports
Two Universal Serial Bus ports are
located on the I/O backplane. USB0
is the bottom connector and USB1 is
the top connector. Two Type A ports
(USB6 and USB7) are also included
on the serverboard (see board layout
for locations) See the table on the right
for pin definitions.
5-15
Pin #
Definition
1
+5V
2
PO-
3
PO+
4
Ground
5
N/A
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Universal Serial Bus Headers
Universal Serial Bus Headers
Pin Definitions (USB2/3, USB4/5)
Four additional USB headers (USB2/3
and USB4/5) are included on the
USB2, USB4
Pin # Definition
serverboard. These may be used for
1
+5V
1
+5V
front side access. A USB cable (not
2
PO-
2
PO-
3
PO+
3
PO+
4
Ground
4
Ground
5
Key
5
NC
included) is needed for the connection. See the table on the right for pin
definitions.
USB3, USB5
Pin # Definition
Serial Port Pin Definitions
(COM1, COM2)
Serial Ports
Pin #
The COM1 serial port is located on
the IO backplane. COM2 is a header
on the serverboard (see serverboard
layout for location). See the table on
the right for pin definitions.
Definition
Pin #
Definition
1
DCD
6
DSR
2
RXD
7
RTS
3
TXD
8
CTS
4
DTR
9
RI
5
Ground
10
NC
Note: Pin 10 is included on the header but not on
the port. NC indicates no connection.
Fan Headers
The X8DTU-F has eight headers,
designated Fan1 through Fan8. FAN1
through FAN6 are for chassis/system
fans while FAN7 and FAN8 are used
to CPU heatsink fans. Their speed is
controlled via Thermal Management
with a BIOS setting. See the table on
the right for pin definitions.
Chassis Intrusion
A Chassis Intrusion header is located
at JL1. Attach the appropriate cable to
inform you of a chassis intrusion.
5-16
Fan Header
Pin Definitions
(FAN1-8)
Pin#
Definition
1
Ground (Black)
2
+12V (Red)
3
Tachometer
4
PWM Control
Chassis Intrusion
Pin Definitions (JL1)
Pin#
Definition
1
Intrusion Input
2
Ground
Chapter 5: Advanced Serverboard Setup
Power LED/Speaker
Speaker Connector
Pin Definitions (JD1)
On the JD1 header, pins 1-3 are for
Pin # Function
Definition
external speaker. See the table on the
4
+
Speaker data (red wire)
right for speaker pin definitions.
5
Key
No connection
a power LED and pins 4-7 are for an
Note: The speaker connector pins are
for use with an external speaker. If you
6
Key
7
Speaker data
wish to use the onboard speaker, you
should close pins 6-7 with a jumper.
PS/2 Keyboard and
Mouse Ports
Pin Definitions
ATX PS/2 Keyboard and PS/2
Mouse Ports
The ATX PS/2 keyboard and the PS/2
mouse ports are located beside the
USB ports. See the table on the right
for pin definitions.
Pin#
Definition
1
Data
2
NC
3
Ground
4
VCC
5
Clock
6
NC
Overheat LED
Overheat LED
Pin Definitions
(JOH1)
Connect an LED to the JOH1 header to
provide warning of a chassis overheating condition. See the table on the right
for pin definitions.
Pin#
Definition
1
+5V
2
OH Active
SGPIO
The two headers labeled T-SGPIO-1
and T-SGPIO-2 are for SGPIO (Serial General Purpose Input/Output).
SGPIO supports serial link interfaces
for onboard SATA and SAS ports. Connect the appropriate cables from the
backplane to the SGPIO1 and SGPIO2
headers to utilize SATA/SAS management functions on your system.
5-17
SGPIO Headers
Pin Definitions (T-SGPIO-1, T-SGPIO-2)
Pin#
Definition
Pin #
Definition
1
NC
2
NC
3
Ground
4
Data
5
Load
6
Ground
7
NC
8
NC
Note: NC indicates no connection.
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Power SMB (I2C) Connector
PWR SMB
Pin Definitions (JPI2C)
The Power System Management Bus
(I2C) header (JPI2C) is used to monitor the power supply, fan and system
temperatures. See the table on the
right for pin definitions.
Pin#
Definition
1
Clock
2
Data
3
PWR Fail
4
Ground
5
+3.3V
IPMB I2C
Pin Definitions (IPMB)
IPMB I2C
A System Management Bus header
for the IPMI slot is located at IPMB.
Connect the appropriate cable here
to use the IPMB I2C connection on
Pin#
Definition
1
Data
2
Ground
3
Clock
your system.
4
No Connection
UID Buttons
There are two Unit Identification (UID)
buttons on the serverboard. The Front
Panel UID Switch connects to pin 13
of JF1. The Rear UID Switch (SW1) is
located next to LAN2. Pushing the UID
switch on the Front Control Panel will
illuminate both the Rear UID and the
Control Panel UID indicators. Push the
either switch again to turn off both indicators. These UID indicators provide
easy identification of a system that may
be in need of service.
LAN1/2 (Ethernet Ports)
Two Ethernet ports (designated LAN1
and LAN2) are located beside the VGA
port on the I/O backplane. These ports
accept RJ45 type cables.
5-18
Chapter 5: Advanced Serverboard Setup
5-9
Jumper Settings
Explanation of Jumpers
To modify the operation of the
serverboard, jumpers can be used
to choose between optional settings.
3
2
1
3
2
1
Connector
Pins
Jumpers create shorts between two
pins to change the function of the
connector. Pin 1 is identified with a
Jumper
square solder pad on the printed circuit board. See the diagram at right for
Setting
an example of jumping pins 1 and 2.
Refer to the serverboard layout page
for jumper locations.
Note: On two-pin jumpers, "Closed"
means the jumper is on and "Open"
means the jumper is off the pins.
CMOS Clear
JBT1 is used to clear CMOS and will also clear any passwords. Instead of pins,
this jumper consists of contact pads to prevent accidentally clearing the contents
of CMOS.
To clear CMOS
1. First power down the system and unplug the power cord(s).
2. With the power disconnected, short the CMOS pads with a metal object such
as a small screwdriver.
3. Remove the screwdriver (or shorting device).
4. Reconnect the power cord(s) and power on the system.
Note: Do not use the PW_ON connector to clear CMOS.
VGA Enable/Disable
JPG1 allows you to enable or disable
the VGA port. The default position
is on pins 1 and 2 to enable VGA.
See the table on the right for jumper
settings.
5-19
VGA Enable/Disable
Jumper Settings (JPG1)
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
SUPERSERVER 1026T-URF/1026T-UF User's Manual
LAN Enable/Disable
LAN Enable/Disable
Jumper Settings (JPL1)
Change the setting of jumper JPL1 to
enable or disable the onboard Ethernet (RJ45) ports LAN1 and LAN2. See
the table on the right for jumper settings. The default setting is enabled.
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
Watch Dog Enable/Disable
JWD1 controls the Watch Dog function.
Watch Dog is a system monitor that
can reboot the system when a software
application “hangs”. Pins 1-2 will cause
WD to reset the system if an application hangs. Pins 2-3 will generate a
non-maskable interrupt signal for the
application that has hung. See the table
on the right for jumper settings. Watch
Dog must also be enabled in BIOS.
Watch Dog
Jumper Settings (JWD1)
Jumper Setting
Definition
Pins 1-2
Reset
Pins 2-3
NMI
Open
Disabled
Note: When enabled, the user needs to
write their own application software to
disable the Watch Dog Timer.
VGA Enable/Disable
JPG1 allows you to enable or disable
the VGA port. The default position is on
pins 1 and 2 to enable VGA. See the
table on the right for jumper settings.
SMB to PCI Express Slots
Jumpers JI2C1 and JI2C2 allow you to
connect the System Management Bus
(I2C) to the PCI Express slots. The
default setting is Open to disable the
connection. See the table on the right
for jumper settings.
5-20
VGA Enable/Disable
Jumper Settings (JPG1)
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
I2C to PCI-Exp
Jumper Settings (JI2C1/2)
Jumper Setting
Definition
Closed
Enabled
Open
Disabled
Chapter 5: Advanced Serverboard Setup
BMC/PHY Reset
Jumper JPRST1 allow the user to reset
the Winbond WPCM450 BMC (Base-
BMC/PHY
Jumper Settings (JPRST1)
board Management Controller) chip
Jumper Setting
Definition
and the PHY chip. The default is set
Closed
Reset BMC & PHY
to Open for normal operation. See the
table on the right for jumper settings.
Open
Normall
Note: For more information on IPMI configuration instructions, please refer to the
Embedded Winbond BMC IPMI user guide posted on our website:
http://www.supermicro.com/support/manuals/.
ME Mode Select
Closing jumper JP3 allows the user to
bypass the SPI flash security and allow
the manufacturer to flash the BIOS on
the production line. See the table on
the right for jumper settings.
ME Mode Select
Jumper Settings (JP3)
Jumper Setting
Definition
Open
Normal
Closed
Manufacture Mode
ME Recovery
Jumper JP5 allows the user to select
the ME Firmware Recovery Mode for
BIOS or firmware recovery. When in
this mode, only essential system functions will be supported. This mode cannot be used for online BIOS upgrades.
See the table on the right for jumper
settings.
5-21
ME Recovery Select
Jumper Settings (JP5)
Jumper Setting
Definition
Open
Normal
Closed
ME Recovery
SUPERSERVER 1026T-URF/1026T-UF User's Manual
5-10 Onboard Indicators
LAN1/LAN2 LEDs
The Ethernet ports (located beside the
VGA port) have two LEDs. On each
LAN LED
Connection Speed Indicator
Gigabit LAN port, one LED indicates
LED Color
Definition
activity when blinking while the other
Off
No connection or 10 Mb/s
LED may be green, amber or off to
indicate the speed of the connection.
Green
100 Mb/s
Amber
1 Gb/s
See the table on the right for the functions associated with the connection
speed LED.
IPMI_Dedicated LAN LEDs
In addition to LAN1 and LAN2, the
X8DTU-F has an IPMI_Dedicated
LAN located on the IO backpanel. The
amber LED indicates activity, while the
Link LED may be green, amber or off
to indicate the speed of the connection. See the tables at right for more
information.
Link
Activity
LED
LED
IPMI LAN Activity Indicator
LED Settings
Color
Status
Definition
Amber
Flashing
Active
IPMI LAN Indicator
LED Settings
LED Color
Definition
Off
No Connection or 10 Mb/s
Green
100 Mb/s
Amber
1 Gb/s
Onboard PWR LED Indicator (LE1)
LED Settings
LE1
An Onboard Power LED is located at
LE1 on the serverboard. When this
LED is on, the system is on. Be sure
to turn off the system and unplug the
power cord before removing or installing components. See the tables at right
for more information.
5-22
LED Color
Definition
Off
System Off/Power cable
not connected
Green
System On
Green:
Flashing
Quickly
ACPI S1 State
Green:
Flashing
Slowly
ACPI S3 State
Chapter 5: Advanced Serverboard Setup
LE2
The LE2 LED (located under SW1) is
the UID indicator LED. LE2 illuminates
when UID is initiated either by the UID
button or via IPMI. If initiated a second
time, LE2 will turn off.
When the LED blinks blue it means the
signal was initiated via IPMI. If blue
continuously it means the UID button
initiated it.
5-11 SATA Port Connections
SATA Ports
SATA Port Pin Definitions
(I-SATA0 ~ I-SATA5)
See the table on the right for
pin definitions for the onboard
SATA ports.
5-23
Pin #
Definition
1
Ground
2
TXP
3
TXN
4
Ground
5
RXN
6
RXP
7
Ground
SUPERSERVER 1026T-URF/1026T-UF User's Manual
5-12 Installing Software
After the hardware has been installed, you should first install the operating system
and then the drivers. The necessary drivers are all included on the Supermicro CDs
that came packaged with your serverboard.
Figure 5-5. Driver/Tool Installation Display Screen
Note: Click the icons showing a hand writing on paper to view the readme files
for each item. Click the computer icons to the right of these items to install each
item (from top to the bottom) one at a time. After installing each item, you must
re-boot the system before moving on to the next item on the list. The bottom
icon with a CD on it allows you to view the entire contents of the CD.
5-24
Chapter 5: Advanced Serverboard Setup
Supero Doctor III
The Supero Doctor III program is a Web base management tool that supports remote
management capability. It includes Remote and Local Management tools. The local
management is called SD III Client. The Supero Doctor III program included on the
CDROM that came with your serverboard allows you to monitor the environment
and operations of your system. Supero Doctor III displays crucial system information
such as CPU temperature, system voltages and fan status. See the Figure below
for a display of the Supero Doctor III interface.
Note: The default User Name and Password for SuperDoctor III is ADMIN / ADMIN.
Note: When SuperDoctor III is first installed, it adopts the temperature threshold
settings that have been set in BIOS. Any subsequent changes to these thresholds
must be made within Super Doctor, as the Super Doctor settings override the BIOS
settings. To set the BIOS temperature threshold settings again, you would first need
to uninstall SuperDoctor III.
Figure 5-6. Super Doctor III Interface Display Screen-I (Health Information)
5-25
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Figure 5-7. Super Doctor III Remote Control Screen
Note: SD III Software Revision 1.0 can be downloaded from our Web Site at: ftp://
ftp.supermicro.com/utility/Supero_Doctor_III/. You can also download SDIII User's
Guide at: http://www.supermicro.com/PRODUCT/Manuals/SDIII/UserGuide.pdf. For
Linux, we will still recommend Supero Doctor II.
5-26
Chapter 6: Advanced Chassis Setup
Chapter 6
Advanced Chassis Setup
This chapter covers the steps required to install components and perform maintenance on the SC113 chassis. For component installation, follow the steps in the
order given to eliminate the most common problems encountered. If some steps
are unnecessary, skip ahead to the next step.
Tools Required: The only tool you will need to install components and perform
maintenance is a Philips screwdriver.
6-1
Static-Sensitive Devices
Electrostatic discharge (ESD) can damage electronic components. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully.
The following measures are generally sufficient to protect your equipment from
ESD damage.
Precautions
•
•
•
•
•
•
Use a grounded wrist strap designed to prevent static discharge.
Touch a grounded metal object before removing any board from its antistatic
bag.
Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or gold contacts.
When handling chips or modules, avoid touching their pins.
Put the serverboard, add-on cards and peripherals back into their antistatic
bags when not in use.
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.
6-1
SUPERSERVER 1026T-URF/1026T-UF Manual
Figure 6-1. Chassis: Front and Rear Views
DVD-ROM Drive
Control Panel
Hot-Swap Drive Bays (8)
Power Supplies
Mouse/Kybrd Dedicated IPMI LAN VGA Port
USB Ports
COM Port
LAN Ports
PCI Slots
UID Button
Note: the 1026T-UF features a single power supply only.
6-2
Control Panel
The control panel (located on the front of the chassis) must be connected to the
JF1 connector on the serverboard to provide you with system status indications. A
ribbon cable has bundled these wires together to simplify the connection. Connect
the cable from JF1 on the serverboard to the appropriate header on the Control
Panel PCB (printed circuit board). Make sure the red wire plugs into pin 1 on both
connectors. Pull all excess cabling out of the airflow path.
The control panel LEDs inform you of system status. See "Chapter 3: System Interface" for details on the LEDs and the control panel buttons. Details on JF1 can
be found in "Chapter 5: Advanced Serverboard Installation."
6-3
System Cooling
Four 4-cm heavy-duty counter-rotating fans provide the cooling for the system.
Each fan unit is actually made up of two fans joined back-to-back, which rotate in
opposite directions. This counter-rotating action generates exceptional airflow and
works to dampen vibration levels. The SC113 chassis provides two additional open
fan housings, where an additional system fan may be added for optimal cooling.
It is very important that the chassis top cover is properly installed and making a
good seal in order for the cooling air to circulate properly through the chassis and
cool the components. See Figure 6-2.
6-2
Chapter 6: Advanced Chassis Setup
Adding a System Fan
1. Turn off the power to the system and unplug the power cord.
2. Remove the chassis cover then remove the dummy fan from the fan tray.
3. Place the new fan into the vacant space in the housing while making sure the
arrows on the top of the fan (indicating air direction) point in the same direction as the arrows on the other fans.
4. Connect the fan wires to the fan header on the serverboard.
5. Power up the system and check that the fan is working properly before replacing the chassis cover.
System Fan Failure
Fan speed is controlled by system temperature via a BIOS setting. If a fan fails,
the remaining fans will ramp up to full speed. Replace any failed fan at your earliest convenience with the same type and model (the system can continue to run
with a failed fan).
The SC113 chassis includes four pre-installed fans. Two additional open slots are
available so that up to two more fans may be added.
Replacing a System Fan (Figure 6-2)
1. Open the chassis while the system is running to determine which fan has
failed. Never run the server for an extended period of time with the chassis
open.
2. Turn off the power to the system and unplug the power cord.
3. Remove the failed fan's wiring from the fan header on the serverboard.
4. Lift the failed fan from the chassis and pull it completely out.
5. Place the new fan into the vacant space in the housing while making sure the
arrows on the top of the fan (indicating air direction) point in the same direction as the arrows on the other fans.
6. Reconnect the fan wires to the same chassis fan header as the previous fan.
7. Power up the system and check that the fan is working properly before replacing the chassis cover.
6-3
SUPERSERVER 1026T-URF/1026T-UF Manual
Figure 6-2: Replacing a System Fan
(shown with optional fan installed)
6-4
Drive Bay Installation/Removal
Accessing the Drive Bays
Hard Drives: Because of their hotswap capability, you do not need to access the
inside of the chassis or power down the system to install or replace hard drives.
Proceed to the next section for instructions.
DVD-ROM Drive: For installing/removing a DVD-ROM drive, you will need to gain
access to the inside of the system by removing the top cover of the chassis. Proceed
to the "DVD-ROM Drive Installation" section later in this chapter for instructions.
Note: Only a "slim" DVD-ROM drive will fit into the 1026T-URF/1026T-UF.
Hard Drive Installation
The hard drives are mounted in drive carriers to simplify their installation and
removal from the chassis. These carriers also help promote proper airflow for
the drive bays. For this reason, even empty carriers without drives installed must
remain in the chassis.
Installing a Hard Drive into a Drive Carrier (Figure 6-3)
1. Insert a drive into the carrier with the PCB side facing down and the connector end toward the rear of the carrier.
6-4
Chapter 6: Advanced Chassis Setup
2. Align the drive in the carrier so that the screw holes of both line up. Note that
there are holes in the carrier marked “SATA” to aid in correct installation.
3. Secure the drive to the carrier with four screws as illustrated below.
4. Insert the drive carrier into its bay, keeping the carrier oriented so that the
hard drive is on the top of the carrier and the release button is on the right
side. When the carrier reaches the rear of the bay, the release handle will
retract.
5. Push the handle in until it clicks into its locked position
Figure 6-3: Installing a Hard Drive into a Carrier
Removing a Hard Drive (Figure 6-4)
1. To remove a carrier, push the release button located beside the drive LEDs.
2. Swing the handle fully out and use it to pull the unit straight out (see Figure
6-4).
Note: Your operating system must have RAID support to enable the hot-plug capability of the hard drives.
Warning! Except for short periods of time (such as for swapping hard drives), do not
operate the server with the hard drive carriers empty.
6-5
SUPERSERVER 1026T-URF/1026T-UF Manual
Figure 6-4. Removing a Hard Drive
2
1
DVD Drive Installation
The SC113 chassis includes a pre-installed DVD-ROM.
Installing or Replacing a DVD-ROM Drive (Figure 6-5)
1. Power down the system and if necessary, remove the server from the rack
and the front bezel from the chassis.
2. Remove the chassis cover.
3. Unplug the drives power and data cables from the serverboard and/or backplane.
4. If you are adding a new drive: Remove the mini-bezel (grate) from the drive
bay The bezel can be removed by pulling out the hard drive beneath the
DVD-ROM, then pulling the mini-bezel forward.
If you are replacing a drive: Locate the locking tab at the rear (left hand side
when viewed from the front) of the DVD-ROM drive. Push the tab toward the
drive and push the drive unit out the front of the chassis.
6-6
Chapter 6: Advanced Chassis Setup
5. Insert the new drive unit in the slot until the tab locks in place.
6. Reconnect the data and power cables.
7. Replace the chassis cover (replace the server in the rack, if necessary) and
power up the system.
Figure 6-5. Installing the DVD-ROM Drive
Drive Screw
Mini Bezel Lock Screw
Drive Screws
6-7
SUPERSERVER 1026T-URF/1026T-UF Manual
6-5
Power Supply
1026T-URF
The SuperServer 1026T-URF has a 650 watt redundant power supply, which is
auto-switching capable. This enables it to automatically sense and operate with a
100V to 240V input voltage. A power on/off switch is included on the back of the
unit. This switch should be turned to the off position before removing the power
cord when replacing the unit.
If either of the two power supply modules fail, the other module will take the full
load and allow the system to continue operation without interruption. The Universal
Information LED on the control panel will blink slowly and remain so until the failed
module has been replaced. Replacement modules can be ordered directly from
Supermicro (see contact information in the Preface). The power supply modules
have a hot-swap capability, meaning you can replace the failed module without
powering down the system.
Replacing the Power Supply (Figure 6-6)
1. Check the LEDs on the power supplies to determine which module has failed.
2. Unplug the power cord from the failed module.
3. Push the release tab (on the back of the power supply) as illustrated.
4. Pull the power supply out using the handle provided.
5. Replace the failed power module with the same model.
6. Push the new power supply module into the power bay until you hear a click.
7. Reconnect the power cord to the new module.
6-8
Chapter 6: Advanced Chassis Setup
1026T-UF
The SuperServer 1026T-UF has a single 560 watt power supply, which is autoswitching capable. This enables it to automatically sense and operate with a 100v
- 240v input voltage.
If the power supply module fails, the system will shut down and you will need to
replace the module. Replacements can be ordered directly from Supermicro (see
contact information in the Preface). As there is only one power supply module in
the 1026T-UF, power must be completely removed from the server before removing
and replacing the power supply for whatever reason. Replacement modules can be
ordered directly from Supermicro (see contact information in the Preface).
Replacing the Power Supply (Figure 6-6)
1. First turn the power switch on the control panel off, then unplug the power
cord from the system.
2. Push the release tab (on the back of the power supply) as illustrated.
3. Pull the power supply out using the handle provided.
4. Replace the failed power module with the same model.
5. Push the new power supply module into the power bay until you hear a click.
6. Reconnect the AC power cord and depress the power button on the control
panel to restart the system.
Figure 6-6. Removing/Replacing the Power Supply
2
Note: 1026T-URF shown - the 1026T-UF has a single (non-hot swappable) power
supply module.
6-9
SUPERSERVER 1026T-URF/1026T-UF Manual
Notes
6-10
Chapter 7: BIOS
Chapter 7
BIOS
7-1
Introduction
This chapter describes the AMI BIOS Setup Utility for the X8DTU-F. The AMI ROM
BIOS is stored in a Flash EEPROM and can be easily updated. This chapter describes the basic navigation of the AMI BIOS Setup Utility setup screens.
Starting BIOS Setup Utility
To enter the AMI BIOS Setup Utility screens, press the <Delete> key while the
system is booting up.
Note: In most cases, the <Delete> key is used to invoke the AMI BIOS setup screen.
There are a few cases when other keys are used, such as <F1>, <F2>, etc.
Each main BIOS menu option is described in this manual. The Main BIOS setup
menu screen has two main frames. The left frame displays all the options that can
be configured. Grayed-out options cannot be configured. Options in blue can be
configured by the user. The right frame displays the key legend. Above the key
legend is an area reserved for a text message. When an option is selected in the
left frame, it is highlighted in white. Often a text message will accompany it. (Note:
the AMI BIOS has default text messages built in. Supermicro retains the option to
include, omit, or change any of these text messages.)
The AMI BIOS Setup Utility uses a key-based navigation system called "hot keys".
Most of the AMI BIOS setup utility "hot keys" can be used at any time during the
setup navigation process. These keys include <F1>, <F10>, <Enter>, <ESC>, arrow keys, etc.
Note: Options printed in Bold are default settings.
How To Change the Configuration Data
The configuration data that determines the system parameters may be changed by
entering the AMI BIOS Setup utility. This Setup utility can be accessed by pressing
<Del> at the appropriate time during system boot.
7-1
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Starting the Setup Utility
Normally, the only visible Power-On Self-Test (POST) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu of
the AMI BIOS Setup Utility. From the main menu, you can access the other setup
screens. An AMI BIOS identification string is displayed at the left bottom corner of
the screen below the copyright message.
Warning! Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event
shall Supermicro be liable for direct, indirect, special, incidental, or consequential damages arising from a BIOS update. If you have to update the BIOS, do not shut down
or reset the system while the BIOS is updating. This is to avoid possible boot failure.
7-2
Main Setup
When you first enter the AMI BIOS Setup Utility, you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on the
top of the screen. The Main BIOS Setup screen is shown below.
System Overview: The following BIOS information will be displayed:
System Time/System Date
Use this option to change the system time and date. Highlight System Time or System Date using the arrow keys. Key in new values through the keyboard and press
<Enter>. Press the <Tab> key to move between fields. The date must be entered in
Day MM/DD/YY format. The time is entered in HH:MM:SS format. (Note: The time
is in the 24-hour format. For example, 5:30 P.M. appears as 17:30:00.)
7-2
Chapter 7: BIOS
AMI BIOS
•
Version: This item displays the BIOS revision used in your system.
•
Build Date: This item displays the date when this BIOS was complete.
Processor
The AMI BIOS will automatically display the status of the processor used in your
system:
•
CPU Type: This item displays the type of CPU used in the serverboard.
•
Speed: This item displays the speed of the CPU detected by the BIOS.
•
•
Physical Count: This item displays the number of processors installed in your
system as detected by the BIOS.
Logical Count: This item displays the number of CPU Cores installed in your
system as detected by the BIOS.
System Memory
This displays the size of memory available in the system:
•
•
Populated Size: This item displays the populated memory size detected by
the BIOS.
Available Size: This item displays the memory size that is available for use.
7-3
SUPERSERVER 1026T-URF/1026T-UF User's Manual
7-3
Advanced Setup Configurations
Use the arrow keys to select Boot Setup and hit <Enter> to access the submenu
items:
BOOT Features
Quick Boot
If Enabled, this option will skip certain tests during POST to reduce the time needed
for system boot. The options are Enabled and Disabled.
Quiet Boot
This option allows the bootup screen options to be modified between POST messages or the OEM logo. Select Disabled to display the POST messages. Select
Enabled to display the OEM logo instead of the normal POST messages. The options are Enabled and Disabled.
AddOn ROM Display Mode
This sets the display mode for Option ROM. The options are Force BIOS and
Keep Current.
Bootup Num-Lock
This feature selects the Power-on state for Numlock key. The options are Off
and On.
PS/2 Mouse Support
Select Enabled to enable PS/2 Mouse support. Select Auto to enable the onboard
PS/2 mouse when a PS/2 mouse is detected. The options are Enable, Disabled,
and Auto.
7-4
Chapter 7: BIOS
Wait For 'F1' If Error
This forces the system to wait until the 'F1' key is pressed if an error occurs. The
options are Disabled and Enabled.
Hit 'Del' Message Display
This feature displays "Press DEL to run Setup" during POST. The options are
Enabled and Disabled.
Watch Dog Function
If enabled, the Watch Dog Timer will allow the system to reboot when it is inactive
for more than 5 minutes. The options are Enabled and Disabled.
Restore on AC Power Loss
Use this feature to set the power state after a power outage. Select Power-Off for
the system power to remain off after a power loss. Select Power-On for the system
power to be turned on after a power loss. Select Last State to allow the system to
resume its last state before a power loss. The options are Power-On, Power-Off
and Last State.
Interrupt 19 Capture
Interrupt 19 is the software interrupt that handles the boot disk function. When this
item is set to Enabled, the ROM BIOS of the host adaptors will "capture" Interrupt
19 at boot and allow the drives that are attached to these host adaptors to function
as bootable disks. If this item is set to Disabled, the ROM BIOS of the host adaptors will not capture Interrupt 19, and the drives attached to these adaptors will not
function as bootable devices. The options are Enabled and Disabled.
Processor and Clock Options
This submenu allows the user to configure the Processor and Clock settings.
CPU Ratio
Select Manual to manually configure the CPU Ratio. Select Auto to allow the BIOS
to automatically configure the CPU Ratio. The options are Auto and Manual.
Clock Spread Spectrum
Select Enable to use the feature of Clock Spectrum, which will allow the BIOS to
monitor and attempt to reduce the level of Electromagnetic Interference caused by
the components whenever needed. The options are Disabled and Enabled.
7-5
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Hardware Prefetcher (Available when supported by the CPU)
If set to Enabled, the hardware pre fetcher will pre fetch streams of data and instructions from the main memory to the L2 cache in the forward or backward manner to
improve CPU performance. The options are Disabled and Enabled.
Adjacent Cache Line Prefetch (Available when supported by the CPU)
The CPU fetches the cache line for 64 bytes if this option is set to Disabled. The
CPU fetches both cache lines for 128 bytes as comprised if Enabled.
Intel® Virtualization Technology (Available when supported by the CPU)
Select Enabled to use the feature of Virtualization Technology to allow one platform
to run multiple operating systems and applications in independent partitions, creating multiple "virtual" systems in one physical computer. The options are Enabled
and Disabled. Note: If there is any change to this setting, you will need to power
off and restart the system for the change to take effect. Please refer to Intel’s web
site for detailed information.
Execute-Disable Bit Capability (Available when supported by the OS and
the CPU)
Set to Enabled to enable the Execute Disable Bit which will allow the processor
to designate areas in the system memory where an application code can execute
and where it cannot, thus preventing a worm or a virus from flooding illegal codes
to overwhelm the processor or damage the system during an attack. The default is
Enabled. (Refer to Intel and Microsoft Web Sites for more information.)
Simultaneous Multi-Threading (Available when supported by the CPU)
Set to Enabled to use the Simultaneous Multi-Threading Technology, which will
result in increased CPU performance. The options are Disabled and Enabled.
Active Processor Cores
Set to Enabled to use a processor's Second Core and beyond. (Please refer to
Intel's web site for more information.) The options are All, 1 and 2.
Intel® EIST Technology
EIST (Enhanced Intel SpeedStep Technology) allows the system to automatically
adjust processor voltage and core frequency in an effort to reduce power consumption and heat dissipation. Please refer to Intel’s web site for detailed information.
The options are Disable (Disable GV3) and Enable (Enable GV3).
Intel® TurboMode Technology
Select Enabled to use the Turbo Mode to boost system performance. The options
are Enabled and Disabled.
7-6
Chapter 7: BIOS
C1E Support
Select Enabled to use the feature of Enhanced Halt State. C1E significantly reduces
the CPU's power consumption by reducing the CPU's clock cycle and voltage during
a "Halt State." The options are Disabled and Enabled.
Intel® C-STATE Tech
If enabled, C-State is set by the system automatically to either C2, C3 or C4 state.
The options are Disabled and Enabled.
C-State package limit setting
If set to Auto, the AMI BIOS will automatically set the limit on the C-State package
register. The options are Auto, C1, C3, C6 and C7.
C1 Auto Demotion
When enabled, the CPU will conditionally demote C3, C6 or C7 requests to C1 based
on un-core auto-demote information. The options are Disabled and Enabled.
C3 Auto Demotion
When enabled, the CPU will conditionally demote C6 or C7 requests to C3 based
on un-core auto-demote information. The options are Disabled and Enabled.
DCA Technology
Select Enabled to use Intel's DCA (Direct Cache Access) Technology to enhance
data transfer efficiency. The options are Enabled and Disabled.
DCA Prefetch Delay
A DCA Prefetch is used with TOE components to prefetch data in order to shorten
execution cycles and maximize data processing efficiency. Prefetching too frequently can saturate the cache directory and delay necessary cache accesses. This
feature reduces or increases the frequency the system prefetches data. The options
are [8], [16], [32], [40], [48], [56], [64], [72], [80], [88], [96], [104], [112], [120]
Advanced Chipset Control
The items included in the Advanced Settings submenu are listed below:
QPI & IMC Configuration
QuickPath Interconnect (QPI) is the connection between the CPU and the
serverboard's I/O hub. Use this feature to modify speed and power management settings.
7-7
SUPERSERVER 1026T-URF/1026T-UF User's Manual
QPI Links Speed
This feature selects QPI's data transfer speed. The options are Slow-mode, and
Full Speed.
QPI Frequency
This selects the desired QPI frequency. The options are Auto, 4.800 GT,
5.866GT, 6.400 GT.
QPI L0s and L1
This enables the QPI power state to low power. L0s and L1 are automatically
selected by the serverboard. The options are Disabled and Enabled.
Memory Frequency
This feature forces a DDR3 frequency slower than what the system has detected.
The available options are Auto, Force DDR-800, Force DDR-1066, and Force
DDR-1333.
Memory Mode
The options are Independent, Channel Mirror, Lockstep and Sparing.
Independent - All DIMMs are available to the operating system.
Channel Mirror - The serverboard maintains two identical copies of all data in
memory for redundancy.
Lockstep - The serverboard uses two areas of memory to run the same set of
operations in parallel.
Sparing - A preset threshold of correctable errors is used to trigger fail-over.
The spare memory is put online and used as active memory in place of the
failed memory.
Demand Scrubbing
A memory error-correction scheme where the Processor writes corrected data
back into the memory block from where it was read by the Processor. The options are Enabled and Disabled.
Patrol Scrubbing
A memory error-correction scheme that works in the background looking for and
correcting resident errors. The options are Enabled and Disabled.
Throttling - Closed Loop/Throttling - Open Loop
Throttling improves reliability and reduces power in the processor by automatic
voltage control during processor idle states. Available options are Disabled and
Enabled. If Enabled, the following items will appear:
7-8
Chapter 7: BIOS
Hysteresis Temperature (This feature is available when Closed Loop
is enabled.)
Temperature Hysteresis is the temperature lag (in degrees Celsius) after the
set DIMM temperature threshold is reached before Closed Loop Throttling
begins. The options are Disabled, 1.5oC, 3.0oC, and 6.0oC.
Guardband Temperature (This feature is available when Closed Loop
is enabled.)
This is the temperature which applies to the DIMM temperature threshold.
Each step is in 0.5oC increment. The default is [006]. Press "+" or "-" on
your keyboard to change this value.
Inlet Temperature
This is the temperature detected at the chassis inlet. Each step is in 0.5oC
increment. The default is [070]. Press "+" or "-" on your keyboard to change
this value.
Temperature Rise
This is the temperature rise to the DIMM thermal zone. Each step is in
0.5oC increment. The default is [020]. Press "+" or "-" on your keyboard to
change this value.
Air Flow
This is the air flow speed to the DIMM modules. Each step is one mm/
sec. The default is [1500]. Press "+" or "-" on your keyboard to change
this value.
Altitude
This feature defines how many meters above or below sea level the system
is located. The options are Sea Level or Below, 1~300, 301~600, 601~900,
901~1200, 1201~1500, 1501~1800, 1801~2100, 2101~2400, 2401~2700,
2701~3000.
DIMM Pitch
This is the physical space between each DIMM module. Each step is in
1/1000 of an inch. The default is [400]. Press "+" or "-" on your keyboard
to change this value.
Intel VT-d
Select Enabled to enable Intel's Virtualization Technology support for Direct I/O VT-d
by reporting the I/O device assignments to VMM through the DMAR ACPI Tables.
This feature offers fully-protected I/O resource-sharing across the Intel platforms,
7-9
SUPERSERVER 1026T-URF/1026T-UF User's Manual
providing the user with greater reliability, security and availability in networking and
data-sharing. The options are Enabled and Disabled.
SR-IOV Supported
Select Enabled to enable Single Root I/O Virtualization (SR-IOV) support which
works in conjunction with the Intel Virtualization Technology and allow multiple operating systems running simultaneously within a single computer via natively share
PCI-Express devices in order to enhance network connectivity and performance.
The options are Enabled and Disabled.
NUMA Support
Select Enabled to use the feature of Non-Uniform Memory Access to improve CPU
performance. The options are Enabled and Disabled.
Intel I/OAT
The Intel I/OAT (I/O Acceleration Technology) significantly reduces CPU overhead
by leveraging CPU architectural improvements, freeing resources for more other
tasks. The options are Disabled and Enabled.
Slot SXB2/SXB3 Width
This feature allows the user to change the link width of a PCI slot as specified in
order to support a riser or add-on card installed in the slot. The options are x4x4x4x4,
x4x4x8, x8x4x4, x8x8, and x16 as shown in the table below.
Options:
SXB2/
SXB3
x4x4x4x4:
x4x4/
x4x4
x4x4x8:
x4x4/
x8
x8x4x4:
x8/
x4x4
x8x8:
x8/
x8
x16:
x16
Slot SXB1 Width
This feature allows the user to change the link width of a PCI slot as specified in
order to support a riser or add-on card installed in the slot. The options are x4x4x4x4,
x4x4x8, x8x4x4, x8x8, and x16.
Active State Power Management
Select Enabled to use the power management for signal transactions between the
PCI Express L0 and L1 Links. Select Enabled to configure PCI-Exp. L0 and L1 Link
power states. The options are Disabled and Enabled.
7-10
Chapter 7: BIOS
USB Functions
This feature allows the user to decide the number of onboard USB ports to be enabled. The Options are: Disabled, 2 USB ports, 4 USB ports, 6 USB ports, 8 Ports,
10 Ports and 12 USB ports.
USB 2.0 Controller
This item indicates if the onboard USB 2.0 controller is activated. The default setting is Enabled.
Legacy USB Support
Select Enabled to use Legacy USB devices. If this item is set to Auto, Legacy USB
support will be automatically enabled if a legacy USB device is installed on the
serverboard, and vise versa. The settings are Disabled, Enabled and Auto.
BIOS EHCI Hand-Off
Select Enabled to enable BIOS Enhanced Host Controller Interface support to
provide a workaround solution for an operating system that does not have EHCI
Hand-Off support. When enabled, the EHCI Interface will be changed from the BIOScontrolled to the OS-controlled. The options are Disabled and Enabled.
IDE/Floppy Configuration
When this submenu is selected, the AMI BIOS automatically detects the presence
of the IDE or Floppy devices and displays the following items:
SATA#1 Configuration
If Compatible is selected, it sets SATA#1 to legacy compatibility mode, while selecting Enhanced sets SATA#1 to native SATA mode. The options are Disabled,
Compatible and Enhanced.
Configure SATA#1 as
This feature allows the user to select the drive type for SATA#1. The options are
IDE, RAID and AHCI. (When the option-RAID is selected, the item-ICH RAID
Code Base will appear. When the option-AHCI is selected, the item-SATA AHCI
will be available.)
SATA#2 Configuration (Available when the option-IDE is selected.)
Selecting Enhanced will set SATA#2 to native SATA mode. The options are
Disabled, and Enhanced.
ICH RAID Code Base (Available when the option-RAID is selected.)
Select Intel to enable Intel's SATA RAID firmware to configure Intel's SATA RAID
settings. Select Adaptec to enable Adaptec's SATA RAID firmware to configure
Adaptec's SATA RAID settings. The options are Intel and Adaptec.
7-11
SUPERSERVER 1026T-URF/1026T-UF User's Manual
SATA AHCI (Available when the option-AHCI is selected.)
Select Enable to enable the function of Serial ATA Advanced Host Interface.
(Take caution when using this function. This feature is for advanced programmers only.)
IDE Detect Timeout (sec)
Use this feature to set the time-out value for the BIOS to detect the ATA, ATAPI
devices installed in the system. The options are 0 (sec), 5, 10, 15, 20, 25, 30, and
35.
PCI/PnP Configuration
Clear NVRAM
This feature clears the NVRAM during system boot. The options are No and Yes.
Plug & Play OS
Selecting Yes allows the OS to configure Plug & Play devices. (This is not required
for system boot if your system has an OS that supports Plug & Play.) Select No to
allow the AMI BIOS to configure all devices in the system.
PCI Latency Timer
This feature sets the latency Timer of each PCI device installed on a PCI bus. Select
64 to set the PCI latency to 64 PCI clock cycles. The options are 32, 64, 96, 128,
160, 192, 224 and 248.
PCI IDE BusMaster
When enabled, the BIOS uses PCI bus mastering for reading/writing to IDE drives.
The options are Disabled and Enabled.
PCIe IO Performance
This feature allows the user to configure PCI-E slot settings to enhance performance. The default setting is 128MB.
PCI SERR Function
PCI SERR (System Error) is for reporting address parity errors, or any other fatal
system errors. It is shared among all PCI devices. The options are Disabled and
Enabled.
PCI SERR Signal Type (Available when PCI SERR Function is enabled.)
System Monitoring Interface (SMI) and Non-Maskable Interrupt (NMI) are
different signal interfaces in the serverboard that handles system errors. The
options are [NMI], and [SMI].
7-12
Chapter 7: BIOS
PCI-E Slot from SXB1/PCI-E Slot from SXB2/PCI-E Slot from SXB3
Select Enabled to enable PCI-E SXB1 slot, PCI-E SXB2 slot or PCI-E SXB3 slot.
It can also enable Option ROMs to boot computer using a network interface from
these slots. (SXB1, a x16 slot, can be configured into two x8 slots. SXB2, a x8 slot,
can be configured into two x4 slots.) The options are Enabled and Disabled.
Onboard LAN Option ROM Select
Select iSCSI to use iSCSI Option ROMs to boot the computing using a network
device. Select iSCSI to use PXE Option ROMs to boot the computing using a
network device. The options are iSCSI and PXE.
Load Onboard LAN1 Option ROM/Load Onboard LAN2 Option ROM
Select Enabled to enable the onboard LAN1 or LAN2 Option ROM. This is to boot
the computer using a network interface. The options are Enabled and Disabled.
Super IO Device Configuration
Uart 2 of Hermon as (Available on X8DTU-F Only)
Select COM to configure the onboard COM 2 port as a normal serial port. Select
SOL to configure the onboard COM 2 port as a virtual COM port for SOL use.
The options are SOL and COM.
Serial Port1 Address/ Serial Port2 Address
This option specifies the base I/O port address and the Interrupt Request address
of Serial Port 1 and Serial Port 2. Select Disabled to prevent the serial port from
accessing any system resources. When this option is set to Disabled, the serial port
physically becomes unavailable. Select 3F8/IRQ4 to allow the serial port to use 3F8
as its I/O port address and IRQ 4 for the interrupt address. The options for Serial
Port1 are Disabled, 3F8/IRQ4, 3E8/IRQ4, 2E8/IRQ3. The options for Serial Port2
are Disabled, 2F8/IRQ3, 3E8/IRQ4, and 2E8/IRQ3.
Remote Access Configuration
Remote Access
This allows the user to enable the Remote Access feature. The options are Disabled and Enabled.
If Remote Access is set to Enabled, the following items will display:
Serial Port Number
This feature allows the user decide which serial port to be used for Console Redirection. The options are COM 1 and COM 2.
7-13
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Serial Port Mode
This feature allows the user to set the serial port mode for Console Redirection.
The options are 115200 8, n 1; 57600 8, n, 1; 38400 8, n, 1; 19200 8, n, 1; and
9600 8, n, 1.
Flow Control
This feature allows the user to set the flow control for Console Redirection. The
options are None, Hardware, and Software.
Redirection After BIOS POST
Select Disabled to turn off Console Redirection after Power-On Self-Test (POST).
Select Always to keep Console Redirection active all the time after POST. (Note:
This setting may not be supported by some operating systems.) Select Boot Loader
to keep Console Redirection active during POST and Boot Loader. The options
are Disabled, Boot Loader, and Always.
Terminal Type
This feature allows the user to select the target terminal type for Console Redirection. The options are ANSI, VT100, and VT-UTF8.
VT-UTF8 Combo Key Support
A terminal keyboard definition that provides a way to send commands from a remote
console. Available options are Enabled and Disabled.
Sredir Memory Display Delay
This feature defines the length of time in seconds to display memory information.
The options are No Delay, Delay 1 Sec, Delay 2 Sec, and Delay 4 Sec.
Hardware Health Monitor
This feature allows the user to monitor system health and review the status of each
item as displayed.
CPU Overheat Alarm
This option allows the user to select the CPU Overheat Alarm setting which determines when the CPU OH alarm will be activated to provide warning of possible
CPU overheat.
Warning! 1.Any temperature that exceeds the CPU threshold temperature predefined
by the CPU manufacturer may result in CPU overheat or system instability. When the
CPU temperature reaches this predefined threshold, the CPU and system cooling
fans will run at full speed. 2. To avoid possible system overheating, please be sure to
provide adequate airflow to your system.
7-14
Chapter 7: BIOS
The options are:
•
The Early Alarm: Select this setting if you want the CPU overheat alarm (including the LED and the buzzer) to be triggered as soon as the CPU temperature
reaches the CPU overheat threshold as predefined by the CPU manufacturer.
•
The Default Alarm: Select this setting if you want the CPU overheat alarm
(including the LED and the buzzer) to be triggered when the CPU temperature
reaches about 5oC above the threshold temperature as predefined by the CPU
manufacturer to give the CPU and system fans additional time needed for CPU
and system cooling. In both the alarms above, please take immediate action
as shown below.
CPU 1 Temperature/CPU 2 Temperature/System Temperature
This feature displays current temperature readings for the CPU and the System.
The following items will be displayed for your reference only:
CPU1 Temperature/CPU2 Temperature
The CPU thermal technology that reports absolute temperatures (Celsius/Fahrenheit) has been upgraded to a more advanced feature by Intel in its newer processors.
The basic concept is each CPU is embedded by unique temperature information that
the serverboard can read. This ‘Temperature Threshold’ or ‘Temperature Tolerance’
has been assigned at the factory and is the baseline on which the serverboard takes
action during different CPU temperature conditions (i.e., by increasing CPU Fan
speed, triggering the Overheat Alarm, etc). Since CPUs can have different ‘Temperature Tolerances’, the installed CPU can now send information to the serverboard
what its ‘Temperature Tolerance’ is, and not the other way around. This results in
better CPU thermal management.
Supermicro has leveraged this feature by assigning a temperature status to certain
thermal conditions in the processor (Low, Medium and High). This makes it easier
for the user to understand the CPU’s temperature status, rather than by just simply
seeing a temperature reading (i.e., 25oC). The CPU Temperature feature will display
the CPU temperature status as detected by the BIOS:
Low – This level is considered as the ‘normal’ operating state. The CPU temperature
is well below the CPU ‘Temperature Tolerance’. The serverboard fans and CPU will
run normally as configured in the BIOS (Fan Speed Control).
User intervention: No action required.
Medium – The processor is running warmer. This is a ‘precautionary’ level and
generally means that there may be factors contributing to this condition, but the CPU
is still within its normal operating state and below the CPU ‘Temperature Tolerance’.
The serverboard fans and CPU will run normally as configured in the BIOS. The fans
may adjust to a faster speed depending on the Fan Speed Control settings.
7-15
SUPERSERVER 1026T-URF/1026T-UF User's Manual
User intervention: No action is required. However, consider checking the CPU fans
and the chassis ventilation for blockage.
High – The processor is running hot. This is a ‘caution’ level since the CPU’s ‘Temperature Tolerance’ has been reached (or has been exceeded) and may activate
an overheat alarm.
User intervention: If the system buzzer and Overheat LED has activated, take action
immediately by checking the system fans, chassis ventilation and room temperature
to correct any problems.
Notes: 1. The system may shut down if it continues for a long period to
prevent damage to the CPU.
2. The information provided above is for your reference only. For more
information on thermal management, please refer to Intel’s Web site at
www.Intel.com.
System Temperature: The system temperature will be displayed (in degrees in
Celsius and Fahrenheit) as it is detected by the BIOS.
Fan 1 ~ Fan 8 Reading
This feature displays the fan speed readings from fan interfaces Fan 1 through
Fan 8.
Fan Speed Control Modes
This feature allows the user to decide how the system controls the speeds of the
onboard fans. The CPU temperature and the fan speed are correlative. When the
CPU on-die temperature increases, the fan speed will also increase, and vice versa.
Select Workstation if your system is used as a Workstation. Select Server if your
system is used as a Server. Select “Disabled, (Full Speed @12V)” to disable the fan
speed control function and allow the onboard fans to constantly run at the full speed
(12V). The Options are: Disabled (Full Speed), 4-pin (Server), 4-pin (Workstation),
4-pin (Quiet) and 4-pin (Super Quiet).
Voltage Monitoring
CPU1 Vcore, CPU2 Vcore, 1.5V, 5V, 5VSB, 12V, -12V, 3.3Vcc, 3.3VSB, VBAT
and Vtt.
ACPI Configuration
Use this feature to configure Advanced Configuration and Power Interface (ACPI)
power management settings for your system.
7-16
Chapter 7: BIOS
High Performance Event Timer
Select Enabled to activate the High Performance Event Timer (HPET) that produces
periodic interrupts at a much higher frequency than a Real-time Clock (RTC) does in
synchronizing multimedia streams, providing smooth playback and reducing the dependency on other timestamp calculation devices, such as an x86 RDTSC Instruction embedded in the CPU. The High Performance Event Timer is used to replace
the 8254 Programmable Interval Timer. The options are Enabled and Disabled.
PS2 KB/MS Wakeup
Select Enabled to "wakeup" the system when you press the PS2 Keyboard or
Mouse. The options are Enabled and Disabled.
ACPI Aware O/S
Select Yes to enable ACPI support for an operating system that supports ACPI.
Select No to disable ACPI support for an OS that does not support ACPI. The options are Yes and No.
ACPI APIC Support
Select Enabled to include the ACPI APIC Table Pointer in the RSDT (Root System
Description Table) pointer list.The options are Enabled and Disabled.
APIC ACPI SCI IRQ
When this item is set to Enabled, APIC ACPI SCI IRQ is supported by the system.
The options are Enabled and Disabled.
Headless Mode
This feature is used to enable system to function without a keyboard, monitor or
mouse attached The options are Enabled and Disabled.
ACPI Version Features
The options are ACPI v1.0, ACPI v2.0 and ACPI v3.0. Please refer to ACPI's website
for further explanation: http://www.acpi.info/.
IPMI Configuration (X8DTU-F Only)
Intelligent Platform Management Interface (IPMI) is a set of common interfaces that
IT administrators can use to monitor system health and to manage the system as a
whole. For more information on the IPMI specifications, please visit Intel's website
at www.intel.com.
IPMI Firmware Version
This item displays the current IPMI Firmware Version.
7-17
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Status of BMC Working
The Baseboard Management Controller (BMC) manages the interface between
system management software and platform hardware. This item displays the status
of the current BMC controller.
View BMC System Event Log
This feature displays the BMC System Event Log (SEL). It shows the total number
of entries of BMC System Events. To view an event, select an Entry Number and
pressing <Enter> to display the information as shown in the screen.
•
Total Number of Entries
•
SEL Entry Number
•
SEL Record ID
•
SEL Record Type
•
Event Timestamp
•
Generator ID
•
Event Message Format User
•
Event Sensor Type
•
Event Sensor Number,
•
Event Dir Type
•
Event Data.
Clear BMC System Event Log
Clear BMC System Log
Select OK and press the <Enter> key to clear the BMC system log. Select Cancel
to keep the BMC System log. The options are OK and Cancel.
Caution: Any cleared information is unrecoverable. Make absolutely sure that you no
longer need any data stored in the log before clearing the BMC Event Log.
7-18
Chapter 7: BIOS
Set LAN Configuration
Set this feature to configure the IPMI LAN adapter with a network address as shown
in the following graphics.
Channel Number - Enter the channel number for the SET LAN Config command. This is initially set to [1]. Press "+" or "-" on your keyboard to change the
Channel Number.
Channel Number Status - This feature returns the channel status for the
Channel Number selected above: "Channel Number is OK" or "Wrong Channel
Number".
IP Address Source
This features allows the user to select how an IP address is assigned to a client computer or network device. Select DHCP (Dynamic Host Configuration
Protocol) to allow a client (computer or device) obtains an IP address from a
DHCP server that manages a pool of IP addresses and network information on
a "request and grant" basis. Upon time-out (or lease expiration), the IP address
assigned to the client can be reassigned to a new client. Select Static (Static
Allocation) to allow the host server to allocate an IP address based on a table
containing MAC Address/IP Address pairs that are manually entered (probably
by a network administrator). Only clients with a MAC address listed in the MAC/
IP Address Table will be assigned an IP address. The IP Address allocated to
the client is on a longer term basis than that assigned by the DHCP mentioned
in the other option. The options are DHCP and Static.
IP Address
The BIOS will automatically enter the IP address of this machine; however it may
be over-ridden. IP addresses are 6 two-digit hexadecimal numbers (Base 16, 0
~ 9, A, B, C, D, E, F) separated by dots. (i.e., 00.30.48.D0.D4.60).
Subnet Mask
This item displays the current subnet mask setting for your IPMI connection. The
value of each three-digit number separated by dots should not exceed 255.
Gateway Address
The BIOS will automatically enter the Gateway address of this machine; however
it may be over-ridden. IP addresses are 6 two-digit hexadecimal numbers (Base
16, 0 ~ 9, A, B, C, D, E, F) separated by dots. (i.e., 00.30.48.D0.D4.60).
Mac Address
The BIOS will automatically enter the Mac address of this machine; however it
may be over-ridden. Mac addresses are 6 two-digit hexadecimal numbers (Base
16, 0 ~ 9, A, B, C, D, E, F) separated by dots. (i.e., 00.30.48.D0.D4.60).
7-19
SUPERSERVER 1026T-URF/1026T-UF User's Manual
SET PEF Configuration
PEF Support
Select Enabled to enable the function of Platform Event Filter (PEF) which will
interpret BMC events and perform actions based on pre-determined settings or
'traps' under IPMI 1.5 specifications. Powering the system down or sending an
alert when a triggering event is detected. The default is Disabled.
The following will appear if PEF Support is set to Enabled.
PEF Action Global Control (Available if the item-PEF Support is enabled)
These are the different actions based on BMC events. The options are Alert,
Power Down, Reset System, Power Cycle, OEM Action, Diagnostic Interface.
Alert Startup Delay (Available if the item-PEF Support is enabled)
This feature inserts a delay during startup for PEF alerts. The options are Enabled and Disabled.
PEF Alert Startup Delay (Available if Alert Startup Delay is enabled)
This sets the pre-determined time to delay PEF alerts after system power-ups
and resets. Refer to Table 24.6 of the IPMI 1.5 Specification for more information
at www.intel.com. The options are No Delay, 30 sec, 60 sec, 1.5 min, 2.0 min.
Startup Delay (Available if the item-PEF Support is enabled)
This feature enables or disables startup delay. The options are Enabled and
Disabled.
PEF Startup Delay (Available if the item-Startup Delay is enabled)
This sets the pre-determined time to delay PEF after system power-ups and
resets. Refer to Table 24.6 of the IPMI 1.5 Specification for more information at
www.intel.com. The options are No Delay, 30 sec, 60 sec, 1.5 min, 2.0 min.
Event Message for PEF Action (Available if the item-PEF Support is
enabled)
This enables of disables Event Messages for PEF action. Refer to Table 24.6 of
the IPMI 1.5 Specification for more information at www.intel.com. The options
are Disabled and Enabled.
BMC Watch Dog Timer Action
Allows the BMC to reset or power down the system if the operating system hangs
or crashes. The options are Disabled, Reset System, Power Down, Power Cycle.
7-20
Chapter 7: BIOS
BMC Watch Dog TimeOut [Min:Sec]
This option appears if BMC Watch Dog Timer Action (above) is enabled. This
is a timed delay in minutes or seconds, before a system power down or reset
after an operating system failure is detected. The options are [5 Min], [1 Min],
[30 Sec], and [10 Sec].
DMI Event Log Configuration
View Event Log
Use this option to view the System Event Log.
Mark All Events as Read
This option marks all events as read. The options are OK and Cancel.
Clear Event Log
This option clears the Event Log memory of all messages. The options are OK
and Cancel.
PCIE Event Log
Select Yes to activate and display the PCI-Express slot event log. The options are
Yes and No.
7-4
Security Settings
The AMI BIOS provides a Supervisor and a User password. If you use both passwords, the Supervisor password must be set first.
7-21
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Supervisor Password
This item indicates if a Supervisor password has been entered for the system. "Not
Installed" means a Supervisor password has not been used.
User Password
This item indicates if a user password has been entered for the system. "Not Installed" means that a user password has not been used.
Change Supervisor Password
Select this feature and press <Enter> to access the submenu, and then type in a
new Supervisor Password.
User Access Level (Available when Supervisor Password is set as above)
Available options are Full Access: grants full User read and write access to the
Setup Utility, View Only: allows access to the Setup Utility but the fields cannot be
changed, Limited: allows only limited fields to be changed such as Date and Time,
No Access: prevents User access to the Setup Utility.
Change User Password
Select this feature and press <Enter> to access the submenu , and then type in a
new User Password.
Clear User Password (Available only when User Password has been set)
This item allows you to clear a user password after it has been entered.
Password Check
This item allows you to check a password after it has been entered. The options
are Setup and Always.
Boot Sector Virus Protection
When Enabled, the AMI BIOS displays a warning when any program (or virus) issues a Disk Format command or attempts to write to the boot sector of the hard
disk drive. The options are Enabled and Disabled.
7-22
Chapter 7: BIOS
7-5
Boot Configuration
Use this feature to configure boot settings.
Boot Device Priority
This feature allows the user to specify the sequence of priority for the Boot Device.
The settings are 1st boot device, 2nd boot device, 3rd boot device, 4th boot device,
5th boot device and Disabled.
•
1st Boot Device - [USB: XXXXXXXXX]
•
2nd Boot Device - [CD/DVD: XXXXXXXXX]
Hard Disk Drives
This feature allows the user to specify the boot sequence from all available hard
disk drives. The settings are Disabled and a list of all hard disk drives that have
been detected (i.e., 1st Drive, 2nd Drive, 3rd Drive, etc).
•
1st Drive - [SATA: XXXXXXXXX]
Removable Drives
This feature allows the user to specify the boot sequence from available Removable
Drives. The settings are 1st boot device, 2nd boot device, and Disabled.
•
1st Drive - [USB: XXXXXXXXX]/2nd Drive
CD/DVD Drives
This feature allows the user to specify the boot sequence from available CD/DVD
Drives (i.e., 1st Drive, 2nd Drive, etc).
7-23
SUPERSERVER 1026T-URF/1026T-UF User's Manual
7-6
Exit Options
Select the Exit tab from the Setup Utility screen to enter the Exit screen.
Save Changes and Exit
When you have completed the system configuration changes, select this option
to leave the BIOS Setup Utility and reboot the computer, so the new system configuration parameters can take effect. Select Save Changes and Exit from the Exit
menu and press <Enter>.
Discard Changes and Exit
Select this option to quit the BIOS Setup without making any permanent changes
to the system configuration, and reboot the computer. Select Discard Changes and
Exit from the Exit menu and press <Enter>.
Discard Changes
Select this option and press <Enter> to discard all the changes and return to the
AMI BIOS Utility Program.
Load Optimal Defaults
To set this feature, select Load Optimal Defaults from the Exit menu and press
<Enter>. Then, select OK to allow the AMI BIOS to automatically load Optimal Defaults to the BIOS Settings. The Optimal settings are designed for maximum system
performance, but may not work best for all computer applications.
Load Fail-Safe Defaults
To set this feature, select Load Fail-Safe Defaults from the Exit menu and press
<Enter>. The Fail-Safe settings are designed for maximum system stability, but not
for maximum performance.
7-24
Appendix A: BIOS Error Beep Codes
Appendix A
BIOS Error Beep Codes
During the POST (Power-On Self-Test) routines, which are performed each time
the system is powered on, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to continue the
boot-up process. The error messages normally appear on the screen.
Fatal errors are those which will not allow the system to continue the boot-up
procedure. If a fatal error occurs, you should consult with your system manufacturer for possible repairs.
BIOS Error Beep Codes
Beep Code
Error Message
Description
1 beep
Refresh
Circuits have been reset.
(Ready to power up)
5 short beeps, 1 long
beep
Memory error
No memory detected in the
system
8 beeps
Display memory
read/write error
Video adapter missing or with
faulty memory
1 continuous beep
(with the front panel
OH LED on)
System Overheat
1 continuous beep with the
front panel OH LED on
A-1
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Notes
A-2
Appendix B: Installing Windows
Appendix B
Installing Windows
After all hardware components have been installed, you must first configure Intel
South Bridge RAID Settings before you install the Windows OS and other software
drivers. To configure RAID settings, please refer to RAID Configuration User Guides
posted on our web site at www.supermicro.com/support/manuals.
B-1 Installing the Windows OS for a RAID System
1. Insert Microsoft's Windows 7/XP/2003/2008/Vista Setup CD in the CD drive,
and the system will start booting up from CD.
2. Press the <F6> key when the message "Press F6 if you need to install a third
party SCSI or RAID driver" displays.
3. When the Windows OS Setup screen appears, press "S" to specify additional
device(s).
4. Insert the driver diskette "Intel AA RAID Windows XP/2003/2008/Vista Driver
for ICH10R" into the floppy drive and press the <Enter> key.
5. Choose the Intel(R) ICH10R SATA RAID Controller from the list indicated in
the Windows OS Setup Screen, and press the <Enter> key.
6. Press the <Enter> key to continue the installation process. (If you need to
specify any additional devices to be installed, do so at this time.) Once all
devices are specified, press the <Enter> key to continue with the installation.
7. From the Windows OS Setup screen, press the <Enter> key. The Windows
OS Setup will automatically load all device files and then, continue the Windows OS installation.
8. After the Windows OS Installation is complete, the system will automatically
reboot.
B-1
SUPERSERVER 1026T-URF/1026T-UF User's Manual
B-2 Installing the Windows OS for a Non-RAID System
1. Insert Microsoft's Windows 7/XP/Windows 2003/Windows 2008/Windows Vista
Setup CD in the CD drive, and the system will start booting up from CD.
2. Continue with the OS installation. The Windows OS Setup screen will display.
3. From the Windows OS Setup screen, press the <Enter> key. The Windows
OS Setup will automatically load all device files and then continue with the
OS installation.
4. After the Windows OS Installation is complete, the system will automatically
reboot.
5. Insert the Supermicro Setup CD that came with your serverboard into the CD
drive during system boot, and the main screen will display.
B-2
Appendix C: System Specifications
Appendix C
System Specifications
Processors
Single or dual Intel® 5500 Series processors in LGA1366 sockets
Note: Please refer to our web site for a complete listing of supported processors.
Chipset
Intel IOH-36D/ICH10R chipset
BIOS
32 Mb AMI® SPI Flash ROM
Memory Capacity
Twelve DIMM sockets supporting up to 96 GB of registered ECC DDR31333/1066/800 SDRAM
See the memory section in Chapter 5 for details.
SATA Controller
Intel ICH10R on-chip controller for six-port Serial ATA (RAID 0, 1 5 and 10
supported)
Drive Bays
Eight SATA drive bays
One slim DVD-ROM drive
Expansion Slots
Right side: (optional) 2x Gb LAN ports w/ RSC-R1UU-E8PR riser card and
AOC-PG-i2+ add-on card
Left side: one UIO card and one PCI Express x16 slot
Serverboard
X8DTU-F (Proprietary form factor)
Dimensions: 12 x 13.05 in (305 x 331 mm)
C-1
SUPERSERVER 1026T-URF/1026T-UF User's Manual
Chassis
1026T-URF: SC113TQ-R650 (1U rackmount form factor)
1026T-UF: SC113TQ-560 (1U rackmount form factor)
Dimensions (both): (WxHxD) 17.2 x 1.7 x 23.5 in. (437 x 43 x 597 mm)
Weight
Gross (Bare Bone): 33 lbs. (15 kg.)
System Cooling
Four 4-cm counter-rotating fans
System Input Requirements
AC Input Voltage: 100-240 VAC
Rated Input Current: 8A (115V) to 4A (230V)
Rated Input Frequency: 50-60 Hz
Power Supply
1026T-URF
Rated Output Power: 650W (Model# PWS-651-1R)
Rated Output Voltages: +5V (25A), +3.3V (12A), +12V (54A), +5Vsb (3A)
1026T-UF
Rated Output Power: 560W (Model# PWS-562-1H20)
Rated Output Voltages: +5V (20A), +3.3V (20A), +12V (46.5A), -12V (0.5A),
+5Vsb (4A)
Operating Environment
Operating Temperature: 10º to 35º C (50º to 95º F)
Non-operating Temperature: -40º to 70º C (-40º to 158º F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)
Regulatory Compliance
Electromagnetic Emissions: FCC Class A, EN 55022 Class A, EN 61000-3-2/3-3, CISPR 22 Class A
Electromagnetic Immunity: EN 55024/CISPR 24, (EN 61000-4-2, EN 610004-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 610004-11)
Safety: CSA/EN/IEC/UL 60950-1 Compliant, UL or CSA Listed (USA and
Canada), CE Marking (Europe)
C-2
Appendix C: System Specifications
California Best Management Practices Regulations for Perchlorate Materials:
This Perchlorate warning applies only to products containing CR (Manganese
Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate”
C-3
SUPERSERVER 1026T-URF/1026T-UF User's Manual
(continued from front)
The products sold by Supermicro are not intended for and will not be used in life support systems,
medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to
result in significant injury or loss of life or catastrophic property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous
applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend
and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
C-4