SB700 INDOOR CYCLE OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW Indoor cycle
TABLE OF CONTENTS
Product Registration
1
Important Safety Instructions
2
Important Operation Instructions
3
SB700 Assembly Instructions
5
Operation of Your New Indoor Cycle
10
Manufacturer’s Limited Warranty
18
ATTENTION
THIS INDOOR CYCLE IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED FOR
THE APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY.
CONGRATULATIONS ON YOUR NEW INDOOR CYCLE AND WELCOME TO THE SOLE FAMILY!
Thank you for your purchase of this quality indoor cycle. Your new indoor cycle has been
manufactured by one of the leading fitness manufacturers in the world and is backed by one of the
most comprehensive warranties available. SOLE will do all we can to make your ownership
experience as pleasant as possible for many years to come.
If you have any questions about your new product or questions about the warranty contact SOLE
Fitness at 1-866-780-SOLE (7653). If you have a technical problem with your new indoor cycle
contact SOLE technical service at 866-MYSOLE1 (697-6531).
Please take a moment at this time to record below the name of the dealer, their telephone number,
and the date of purchase for easy contact in the future. We appreciate your confidence in SOLE and
we will always remember that you are the reason that we are in business. Please complete and mail
your registration card today and enjoy your new indoor cycle.
Yours in Health,
SOLE Fitness
Name of Dealer
Telephone Number of Dealer
Purchase Date
PRODUCT REGISTRATION
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this fitness product
in the space provided below.
Serial Number
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to SOLE.
You can also go to www.soletreadmills.com under the support tab to register online.
SB700_20110106
1
SB700 INDOOR CYCLE
IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this appliance.
1. Use this equipment only for its intended use as described in this manual. Do not attempt
to ride this bike at high pedal speeds until you have ridden the bike for some time and are
comfortable riding at slower pedal speeds.
2. The bike is NOT equipped with a freewheel system which means that when the flywheel is
in motion, the pedals will be in motion. Do not attempt to stop the unit by applying backward pressure to pedals while they are turning as knee injury may occur. Do not attempt to
remove your feet from pedals while they are moving.
3. Wait for flywheel to coast to a stop before dismounting the bike. If you want to stop the
flywheel, push down on the brake knob.
4. Serious injury or death may occur from over-training. Consult a medical doctor or qualified
fitness instructor to determine an exercise program appropriate for your level of fitness.
5. Do not attempt to turn the pedal cranks by hand. Do not touch any driving mechanism
while it is in motion as possible injury could occur.
6. In a home setting, keep children away from the bike when it is not in use. Keep children and
pets away from the unit while it is in use.
7. Do not attempt to perform dip movements on handlebars.
8. Never drop or insert any object into any opening of the bike.
9. Only use the bike on a stable, level floor.
10.Follow instructions for safe use of the equipment including proper seat position, handlebar
position, and use of foot positioning system of pedals. Do not attempt to pull up handlebar
post and seat post over the ‘MAX.’ graduation.
11.For safe operation, allow for at least 1foot (30cm) of free space to either side of the unit and
2 feet (60cm) of free space to the rear of the unit.
Regularly examine the bike for damage and wear. Inoperable components should be replaced
immediately or the equipment should not be used until it is repaired.
Failure to follow all guidelines may compromise the effectiveness of the exercise experience,
expose yourself (and possibly others) to injury, and reduce the longevity of the equipment.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
SB700 INDOOR CYCLE
2
IMPORTANT OPERATION INSTRUCTIONS
WARNING - AS THE OWNER OF THIS EXERCISE EQUIPMENT, YOU SHOULD INSIST THAT ALL
USERS FOLLOW THE SAME GUIDELINES: YOU SHOULD MAKE THIS MANUAL AVAILABLE
TO ALL USERS.
1. Obtain a complete physical examination from your medical doctor and enlist a health/
fitness professional’s aid in developing an exercise program suitable for your current health
status.
2. When working out for the first time, start out slowly for a minimum of five minutes. After
your muscles are warmed up, gradually increase the pedaling speed and/or resistance.
3. The speed and duration of your exercise program should always be subject to how you feel.
Never permit peer pressure to exceed your personal judgment while exercising.
4. Overweight or severely de-conditioned individuals should be particularly cautious when
using the equipment for the first time. Even though such individuals may not have histories
of serious physical problems, they may perceive the exercise to be far less intense than it
really is, resulting in the possibility of overexertion or injury.
5. Proper installation and regular maintenance are required to ensure user’s safety.
Maintenance is the sole responsibility of the owner.
3
SB700 INDOOR CYCLE
1
SB700 ASSEMBLY PACK CHECKLIST
HARDWARE STEP 1
#82. 3/8”
Nut (4 pcs)
2
#81. 3/8” x 3-1/2”
Button Head Socket Bolt (4 pcs)
#83. 3/8” x 23mm
Flat Washer (4 pcs)
HARDWARE STEP 2
#91. M5 x 10mm
Screw (2 pcs)
4
HARDWARE STEP 4
#49. 5/16”
Split Washer (4 pcs)
#48. 5/16” x 16mm
Flat Washer (4 pcs)
#88. 5/16” x 15mm
Screw (4 pcs)
ASSEMBLY TOOLS
#85. Wrench
SB700 INDOOR CYCLE
#92. Combination M5 Allen Wrench &
Phillips Head Screw Driver
4
SB700 ASSEMBLY INSTRUCTIONS
PRE-ASSEMBLY
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along
the dotted Line. Lift Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or missing
parts. If damaged parts are found, or parts are missing, contact your dealer
immediately.
3. Locate the hardware package. Remove the tools first. Remove the hardware
for each step as needed to avoid confusion. The numbers in the instructions
that are in parenthesis (#) are the item number from the assembly drawing
for reference.
1
STABILIZER TUBES
HARDWARE STEP 1
#82. 3/8” Nut (4 pcs)
#81. 3/8” x 3-1/2”
Button Head Socket
Bolt (4 pcs)
#83. 3/8” x 23mm
Flat Washer (4 pcs)
82
83
81
82
83
81
1. Attach the Front ( the one with the wheels mounted in the bottom of the
tube) & Rear floor stabilizer tubes by inserting two Button Head Socket Bolts
(81) through each tube. Fasten two Curved Washers (83) and two Nuts (82)
on each tube using the wrench (85) provided.
5
SB700 INDOOR CYCLE
2
REAR STABILIZER COVER
HARDWARE STEP 2
#91. M5 x 10mm
Screw (2 pcs)
91
1. Attach the Rear Stabilizer cover with two Screws (91). Tighten using the
Combination M5 Allen Wrench & Phillips Head Screw Driver (86).
3
CONSOLE
1
2
3
4
1 – Console
2 – Mounting Clamp
3 – Clamp mounting screw
4 – Clamping thumb screw
5 – Velcro
6 – Speed transmitter
6
SB700 INDOOR CYCLE
6
5
Sole Indoor Cycling Console Battery Installation:
1. Remove the battery cover from the back of the computer.
2. Insert 2 AAA batteries into the battery compartment and reinstall the battery cover.
3. When Battery working voltage is too low, The “Low battery” indicator will show up on the
console display indicating it is time to change the batteries.
Speed Sensor Transmitter Battery Installation
1. Remove the battery cover from the transmitter.
2. Install 2 AAA batteries in the battery compartment and reinstall the battery cover.
3. When new batteries are installed in the transmitter or console you must perform the
synchronizing procedure below for the console to work properly
Synchronizing the transmitter to the console:
After installing the batteries, and before attaching the console and transmitter to the bike, you
must synchronize the two so they can ‘talk’ to each other.
1. Press and hold the two keys on the front of the console for about 3 seconds until the
display shows ID - 2. Now press and hold the blue button on the transmitter for 3 seconds and release. The
console display should show ID 0. NOTE: You must press the blue button within 10 seconds
after the console is showing ID - - otherwise the console will show: ID ER. If the console
shows this error then restart the procedure again.
3. It may be necessary to remove and re-install the batteries in both the
console and transmitter if you continue to receive an error.
Console Installation:
1. Install the mounting clamp (2) to the back of the console (1) with the clamp mounting
screw (3).
2. Install and slightly tighten the thumb screw (4) then adjust the console angle for optimal
visibility. Once the console is adjusted, continue to tighten the screw until it is securely
attached to the handle bar.
Transmitter Installation:
• Make sure to route the speed sensor wire behind the frame member. Plug the sensor wire
into the transmitter as shown below
• Install the transmitter, at the angle shown below, onto the pre-installed Velcro strip located
on the back of the chain cover. Make sure the sensor wire connection is at the top left
when mounting the transmitter.
• Make sure the sensor wire is routed away from the spinning flywheel
7
SB700 INDOOR CYCLE
4
HANDLEBAR
HARDWARE STEP 4
#49. 5/16” Split
Washer (4 pcs)
#48. 5/16” x 16mm
Flat Washer (4 pcs)
#88. 5/16” x 15mm
Screw (4 pcs)
1. Attach the handlebars (make sure they are oriented as in the illustration) with
four Screws (88), four Split Washers (49), and four Flat Washers (48). Tighten
firmly using the Combination M5 Allen Wrench & Phillips Head Screw Driver
(86).
SB700 INDOOR CYCLE
8
5
LEFT/RIGHT PEDALS
25(R)
25(L)
1. Attach the Right and Left pedals to the appropriate crank. The pedals have an
“R” and an “L” stamped on the end of the threaded area to distinguish them.
Check the illustrations to make sure you are attaching each to the correct
side. Note: the left side has left hand threads; therefore you will screw it on
in a counterclockwise direction. Tighten each pedal as firmly as possible
with the Wrench (85) provided. If you here a thumping sound when you are
pedaling, this usually means one or both pedals are loose. You may need to
retighten them after use.
9
SB700 INDOOR CYCLE
OPERATION OF YOUR INDOOR CYCLE
GETTING FAMILIAR WITH THE CONTROL PANEL
SB700 CONSOLE
PLEASE NOTE:
1. The Sole Indoor Cycling Console system is designed as a sealed unit and not meant to be opened other than
for the sole purpose of installing batteries. Any opened units will void the warranty.
2. To clean the Sole Indoor Cycling Console use a clean damp cloth. Use of any caustic cleaning solutions will void
the warranty.
3. The Sole Indoor Cycling Console system is NOT waterproof, only water resistant. Any excessive exposure to
water will void the warranty.
The Sole Indoor Cycling Console carton consists of a computer console and a speed sensor transmitter.
The transmitter counts the number of times the magnet, which is mounted on the crank assembly, passes the
sensor. The speed sensor transmitter will then send a coded signal to the console which contains the measured
value (Speed and Cadence ).
SB700 INDOOR CYCLE
10
CONSOLE OPERATION
TIME
Time is measured in min:sec. There is a time of day clock and a workout timer clock. The workout
time will count up or count down during pedaling. If pedaling stops, the time will stop counting
after 3sec.
RPM/CADENCE
Cadence is the measurement of how fast the cranks are rotating in RPM. The approximate speed
of the bike can also be displayed in MPH or KPH. In addition to MPH/KPH, the RPM section of the
display also has a bar graph that allows the rider to visually keep track of the approximate RPM.
DISTANCE
Distance is the measurement of the virtual distance traveled on the bike. This distance is based
on the user riding a bike with tires that are the same size as the Xterra group bike’s flywheel.
KCAL
Kcal is the approximation of calories burned during your work out. The calories are an estimate
only.
HEART RATE
This the approximation of heart rate detected from the chest strap (sold separately) during your
work out.
QUICK START
When the console is in Power Saving Mode, hold down any key to wake up the console and go
to the start-up screen, also called “QUICK Start” active state.
POWER SAVING MODE
QUICK START MODE
11
SB700 INDOOR CYCLE
MODE SELECT
Press the left hand key to select the SPEED, DIST, TIME or CLOCK at the bottom of the display.
RESET/HEART RATE ALARM SELECT
1. Press the right hand key to activate the heart rate (this will only
register if you are wearing the chest strap which is sold separately).
If the alarm is on, the alarm icon will flash and a beep will sound to
indicate that your heart rate is either above or below the selected
target zone.
2. To clear the exercise Time, press the left hand key until the time is
displayed, then hold the right hand key for three seconds.
HEART RATE TARGET ZONES
1. Press the left hand key until ‘SPEED’ is
displayed, then hold the right hand key for
3 seconds. The TIME will be flashing; press
the left hand key to select the heart rate
target zone settings.
2. Press the right hand key to increase maximum heart rate limit. After setting the maximum heart rate, press the left hand key to
adjust the minimum heart rate limit.
SB700 INDOOR CYCLE
12
HEART RATE TARGET ZONES
1. GENDER: Press the left hand key until SPEED is displayed, then press the right hand key for 3
seconds. The TIME will be flashing, press the left hand key until the gender icon is blinking.
Press the right hand key to select gender.
2. Press the left hand key to set the measuring value for weight (Lb or Kg); press the right hand
key to select.
3. BODYWEIGHT: Press the left hand key to set the bodyweight. Press the right hand key to
increase the weight. Press and hold the right hand key for rapid advance.
13
SB700 INDOOR CYCLE
FIRST TIME USER INSTRUCTIONS
ADJUSTING THE BIKE FOR A PROPER FIT
Take some time to learn how to properly adjust the bike to your body; it will make your
workouts more pleasant and a safer experience too. Riding the bike when it is incorrectly
adjusted can result in discomfort and increase your risk of injury.
ADJUSTMENT OF SEAT POSITION
Seat Height Adjustment
1. Standing next to the bike, adjust the seat until it is about hip height.
2. Rotate the crank arms until the pedals are in the vertical position: 12 and 6 o’clock.
3. Place your foot in the toe cage of the pedal closest to the floor and mount the bike.
Ensure that the ball of your foot is over the center of the pedal. Your leg should be
slightly bent at the knee, about 5 degrees.
4. If your leg is too straight or your foot cannot touch the pedal you will need to lower
the seat height. If your leg is bent too much, you will need to raise the seat height.
5. Dismount the bike. Then loosen the quick release lever on the seat post and adjust
up or down as necessary.
6. When the seat is in the desired position, tighten the quick release to secure the seat
post.
7. Note the final position mark on the seat post for future reference.
Seat Forward/Aft Adjustment
8. Sit on the bike with the crank arms in the 3 and 9 o’clock positions. A proper
forward/aft position (for road bike training) of the seat is achieved when the small
bump at the top of your shin is above the pedal axle.
9. Dismount the bike. Loosen the quick release under the seat and slide the seat
forward or backward as desired; tighten the quick release lever.
HANDLE BAR ADJUSTMENT
Handlebar Height Adjustment
1. The handlebar height is a matter of preference. Start with a handlebar height that
is the same as the seat’s height. Adjusting the handlebar higher will give the rider a
more upright position; lower will result in a more crouched position.
2. Raise or lower the handlebar by loosening the quick release on the handlebar post
and adjust by sliding the handlebar mount up or down as desired. Then tighten
the quick release to secure the handlebar post. Note the final position mark on the
handlebar post for future reference.
Adjustment of Handlebar’s Forward/Aft Position
3. Loosen the quick release under the handlebar and slide the handlebar forward or
backward as desired. A suitable forward/aft position should allow the rider to
comfortably grasp the handlebar with a slight bend at the elbow.
4. Tighten the quick release to secure the handlebar assembly.
SB700 INDOOR CYCLE
14
DUAL FUNCTION PEDAL
ATTACHING CLEATS TO YOUR SHOES
If you have questions, it is recommended that you consult a bicycle dealer for assistance and
also refer to your shoe manufacturer’s instructions. When fixing the cleat, the lateral center line
should be under the center of the ball of the foot. Adjust forward and backward via the slots in
the shoe sole. Adjust laterally via play between cleat washer and cleat. Tighten cleats very firmly.
Cleat position can be fine-tuned according to personal preference, after trial use. It may take
time to find your optimum cleat set-up.
TOE CLIPS
All standard toe clips can be attached to the pedals. Use fixing hardware and installation
instructions supplied with toe clips and ensure the attachment screws are firmly tightened
before use.
TO USE PEDALS
Engage cleated shoes in pedals by placing cleat between bindings while pushing down.
Disengage by twisting heel outwards away from exercise bike. Binding tension is adjustable and
should be set so that the cleat and shoe do not disengage when pedaling. Use an Allen wrench
to turn tension adjusting screws, clockwise to increase binding tension, counterclockwise to
decrease binding tension.
Use the opposite side of the pedal from the clip-in side when wearing regular sports training
shoes. The regular side can be used with or without toe clips.
15
SB700 INDOOR CYCLE
BASIC OPERATION
Now that you have established a proper riding position, take a few minutes to ride the bike and
determine that your position is comfortable. Start pedaling at a slow pace with your toes and
knees pointed directly forward. Hold the handlebar lightly and in a position that allows your
shoulders and upper body to relax. Pedal easily, at a low resistance until you feel confident that
you could ride in that position for the duration of your workout.
WARNING!
IF AT ANY TIME DURING YOUR WORKOUT, YOU FEEL CHEST PAIN, EXPERIENCE SEVERE
MUSCULAR DISCOMFORT, FEEL FAINT, OR ARE SHORT OF BREATH, STOP EXERCISING AT ONCE.
IF THE CONDITION PERSISTS, YOU SHOULD CONSULT YOUR MEDICAL DOCTOR IMMEDIATELY.
1. Pedaling resistance is controlled by the tension knob. Resistance can be changed at any time
by turning tension knob: clock-wise for more resistance; counterclockwise for less resistance.
2. To apply the brake, press down on the tension knob.
3. Before dismounting, apply the brake to stop flywheel, or increase resistance and let flywheel
come to a stop.
SB700 INDOOR CYCLE
16
TROUBLESHOOTING
No Display on Console
1. Hold down any key to bring the console to “Quick Start” mode.
2. Ensure that the batteries are installed properly in the console and transmitter. If they are,
install fresh batteries.
No Heart Rate signal displayed (chest strap transmitter sold separately)
1. Ensure that your chest strap is worn correctly and that there is moisture under the electrodes.
2. Relocate the bike away from any equipment that could potentially interrupt the radio frequency signal, such as a DVD player or television, etc.
Cadence number jumps high or low
1. Separate bikes that may be set to the same console code and are cross-talking, or re-synchronize the transmitter and console (see page 7).
2. Relocate the bike to a different part of the room, away from any RF interference areas.
Heart Rate signal gets interrupted or drops out (chest strap transmitter sold separately)
1. Ensure that there is a minimum distance of 36 inches between bikes.
2. Verify that your chest strap is secure and that the electrodes are making contact with your
chest at all times.
CAUTION!!
EXTERNAL INTERFERENCE MAY BE CAUSED BY OTHER ELECTRONIC DEVICES, SUCH AS: NEARBY
TELEVISIONS, STEREO EQUIPMENT, SPEAKERS, ELECTRICAL WIRE CABLING, ETC. IF YOU
EXPERIENCE DISTURBANCES IN THE CONSOLE DISPLAY TRY MOVING YOUR BIKE(S) AWAY
FROM POTENTIAL RF INTERFERENCE AREAS.
MAINTENANCE GUIDELINES
MAINTENANCE SCHEDULE
PART
Pedals
RECOMMENDED ACTION
FREQUENCY
Ensure that pedals are tight in Before each
crank arms; that all screws on
use
pedals are tight; and that the
pedal straps are not frayed
Frame
Wipe down by using a soft
Daily
damp clean cloth
Flywheel Wipe down by spraying on a
Weekly
rag and applying a light coat
to sides of the flywheel
Brake
Inspect for excessive wear or
Weekly
Pad
a dry leather brake pad
CLEANER
N/A
LUBRICANT
N/A
Water
N/A
WD-40
spray.
N/A
N/A
3-IN-ONE Oil or 10W
oil. Do not use
silicone-based
lubricants
1. Do not service internal parts of pedals. If they are found to be worn internally, we
recommend replacing the pedal.
2. Use of lubricants or cleaning solutions other than those so specified will result in
diminished performance and a shorter life span for that part.
17
SB700 INDOOR CYCLE
MANUFACTURER’S LIMITED WARRANTY
INDOOR CYCLE WARRANTY
Effective January 1, 2011
SOLE warrants all its indoor cycles’ parts for a period of time listed below from the date of retail sale, as determined by sale receipt, or in the absence
of a sales receipt eighteen (18) months from the original factory shipping date. SOLE’s responsibilities include providing new or remanufactured parts,
at SOLE’s option, and technical support to our independent dealers and servicing organizations. In the absence of a dealer or service organization,
these warranties will be administered by SOLE directly to a consumer. The warranty period applies to the following components:
HOME USE LIMITED WARRANTY
Frame
Parts
Lifetime
1 Years
NORMAL RESPONSIBILITIES OF THE CONSUMER
This warranty applies only to products in ordinary household use, and the consumer is responsible for the items listed below:
1. The warranty registration card must be completed and returned to the address listed on the card within 10 days of the original purchase to
validate the manufacturer’s limited warranty.
2. Proper use of the indoor cycle in accordance with the instructions provided in this manual
3. Proper installation in accordance with instructions provided with the indoor cycle
4. Expenses for making the indoor cycle accessible for servicing, including any item that was not part of the indoor cycle at the time it was shipped
from the factory.
5. Damages to the indoor cycle finish during shipping, installation or following installation.
6. Routine maintenance of this unit as specified in this manual.
EXCLUSIONS
This warranty does not cover the following:
1. CONSEQUENTIAL, COLLATERAL, OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.
2. Service call reimbursement to the consumer. Service call reimbursement to the dealer that does not involve malfunction or defects in
workmanship or material, for units that are beyond the warranty period, for units that are beyond the service call reimbursement period, for
indoor cycle not requiring component replacement, or indoor cycle not in ordinary household use.
3. Damages caused by services performed by persons other than authorized SOLE service companies; use of parts other than original SOLE parts;
or external causes such as corrosion, discoloration of paint or plastic, alterations, modifications, abuse, misuse, accident, improper maintenance,
inadequate power supply, or acts of God.
4. Products with original serial numbers that have been removed or altered.
5. Products that have been: sold, transferred, bartered, or given to a third party.
6. Products that do not have a warranty registration card on file at SOLE. SOLE reserves the right to request proof of purchase if no warranty record
exists for the product.
7. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY
AND/OR FITNESS FOR A PARTICULAR PURPOSE.
8. Product use in any environment other than a residential setting.
9. Warranties outside of North America may vary. Please contact your local dealer for details.
SERVICE
Keep your bill of sale. Twelve (12) months from the date on the bill of sale or eighteen (18) months from the date of factory shipping as determined
by the serial number establishes the labor warranty period should service be required. If service is performed, it is in your best interest to obtain and
keep all receipts. This written warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service under this
warranty must be obtained by following these steps, in order:
1. Contact your selling authorized SOLE dealer. OR
2. Submit all service requests including serial number, contact information and a brief description of the problem online at www.soletreadmills.
com/technical.php?p=service.
3. If you have any questions about your new product or questions about the warranty contact SOLE Fitness at 1-866-780-SOLE (7653). If you have a
technical problem with your new indoor cycle contact SOLE technical service at 866-MYSOLE1 (697-6531).
4. If no local service is available, SOLE will repair or replace the parts, at SOLE’s option, within the warranty period at no charge for parts. All
transportation costs, both to our factory and upon return to the owner, are the responsibility of the owner. The owner is responsible for
adequate packaging upon return to SOLE. SOLE is not responsible for damages that occur during shipping. Make all freight damage claims with
the appropriate freight carrier. DO NOT SHIP ANY UNIT TO OUR FACTORY WITHOUT A RETURN AUTHORIZATION NUMBER. All units arriving without a return authorization number will be refused.
5. For any further information, or to contact our service department by mail, send your correspondence to:
SOLE Fitness
P.O. Box 2037
Jonesboro, AR 72402-2037
Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by SOLE.
SB700 INDOOR CYCLE
18
Open as PDF
Similar pages