TSHARC “C-Ray” Capacitive Touch Screen Controller Board (RS

M:\03_Products\TSHARC_Boards\TSHARC_C-Ray\C_Ray_3.3A\C-Ray_3.3_UsersManual\08B_TSHARC_C-Ray_Users_Rev3.3x_081121.doc
Setup and User’s Manual
TSHARC “C-Ray” Capacitive
Touch Screen Controller Board
(RS-232 and USB)
Version 3.3x
Document Revision and Copyright
Document Name: 08B_TSHARC_C-Ray_Users_Rev3.3x_081121.doc
Document Date: November 21, 2008
Copyright Hampshire Company, Inc.
1995 – 2008 All rights reserved
Hampshire® TSHARC™ and UniWInDriver™ are the exclusive trademarks of
Hampshire Company, Inc. Elo and 3M (Microtouch) are trade names of Tyco
Electronics and 3M Company respectively. All Rights Reserved.
Contact Information
Hampshire Company, Inc.
st
9055 N. 51 Street, Suite H
Brown Deer, WI 53223
www.hampshirecompany.com
Phone: 414-355-4675
Fax: 414-355-4775
Table of Contents
IMPORTANT DOCUMENT AND USER INFORMATION .............................................................................................. 3 GENERAL INFORMATION ........................................................................................................................................... 3 MAILING ADDRESS: ......................................................................................................................................................... 3 WORLD WIDE WEB: ....................................................................................................................................................... 3 SUPPORT E-MAIL ADDRESS ............................................................................................................................................ 3 COPYRIGHT INFORMATION............................................................................................................................................... 3 EDITION INFORMATION .................................................................................................................................................... 3 PRODUCT DESCRIPTION ............................................................................................................................................ 4 PART NUMBER INFORMATION .......................................................................................................................................... 4 INTEGRATING THE TSHARC CAPACITIVE CONTROLLER ...................................................................................... 4 MOUNTING THE CONTROLLER .......................................................................................................................................... 4 Figure 4.0: Controller Mounting Diagram.................................................................................................................. 4 MOUNTING THE CAPACITIVE TOUCH SCREEN .................................................................................................................... 5 CONNECTING THE TOUCH SCREEN................................................................................................................................... 5 Figure 5.0: Touch Screen Connection Diagram ....................................................................................................... 5 COMMUNICATION JUMPER CONFIGURATIONS ...................................................................................................... 6 Figure 6.0: Jumper Selectable Communications ...................................................................................................... 6 CONNECTING THE C-RAY FOR RS-232 COMMUNICATION ................................................................................................... 6 Figure 6.1: RS-232 Cable Connection Diagram ....................................................................................................... 6 CONNECTING THE C-RAY FOR USB COMMUNICATIONS ...................................................................................................... 7 Figure 7.0: USB Cable Connection Diagram ............................................................................................................ 7 ADDITIONAL CONNECTION INFORMATION .......................................................................................................................... 7 COMMUNICATION PROTOCOL................................................................................................................................... 8 Table 8.0: Hampshire standard USB Protocol .......................................................................................................... 8 Table 8.1: Hampshire standard RS-232 Protocol ..................................................................................................... 8 POWERING YOUR SYSTEM ........................................................................................................................................ 8 STATIC PROTECTION WARNING ....................................................................................................................................... 8 STATUS LED INDICATOR................................................................................................................................................. 8 SOFTWARE DEVICE DRIVERS ................................................................................................................................... 9 SAVING CALIBRATION TO EEPROM ................................................................................................................................ 9 HAMPSHIRE SUPPORT SERVICES ............................................................................................................................ 9 APPENDIX ................................................................................................................................................................... 10 PRODUCT SPECIFICATIONS ........................................................................................................................................... 10 MECHANICAL DIAGRAM ................................................................................................................................................. 10 Figure 10.0: Mechanical Diagram of TSHARC C-Ray Touch Screen Controller Board .......................................... 10 QUICK VIEW SETUP ...................................................................................................................................................... 11 Figure 11.0: Quick View Setup Diagram ................................................................................................................ 11 CABLES AVAILABLE FROM HAMPSHIRE ........................................................................................................................... 12 Table 12.0: Available Communication Cables ........................................................................................................ 12 Table 12.1: Available Power Cables ....................................................................................................................... 12 NOTES ......................................................................................................................................................................... 13 2
IMPORTANT DOCUMENT AND USER INFORMATION
This document is to be used as a guide only. The information contained in this document is subject to change
without notice. This document and all of its contents are protected under US and international copyright law.
Hampshire Company trademarks, patents and copyrights are the exclusive property of Hampshire Company, Inc. and
may not be used without the express written consent of Hampshire Company, Inc.
Due to the vast range of application variables that fall outside of Hampshire’s expertise and control, Hampshire
assumes no responsibility for the usability or the suitability of Hampshire products in customer application(s).
Hampshire assumes those responsible for the application and use of Hampshire Company products and
documentation have taken all necessary steps to insure that the application of Hampshire products meet any and all
safety and performance requirements including any laws, regulations, codes and standards associated with the
application. In no case does Hampshire warrant the usability or suitability of its products in any medical, aviation,
military or other life critical applications. User should contact Hampshire Company before integrating any Hampshire
hardware or software product into these types of applications.
All Hampshire standard software products, including but not limited to device driver software, are provided “as is” and
may be used exclusively with an authentic Hampshire TSHARC touch screen controller. Hampshire does not
warrantee or guarantee the usability of any of its software products.
Hampshire Company warrants to the original purchaser, or a third party who is listed on the Hampshire “Multi Party
Authorization Agreement”, that for the warranty period identified by Hampshire warranty for the specific product that
you have purchased, that the goods will be in conformance with Hampshire specifications. In addition to Hampshire
specifications, the warrantee includes Non-Hampshire specifications agreed-to, in writing, by Hampshire in advance
for the limited purpose between the customer and Hampshire Company. The warrantee also insures that the goods
will be free from defects in design and material for the warrantee period. Hampshire Company, at its option, will
repair or replace the nonconforming or defective goods, issue a credit memorandum, or refund the purchase price, as
its sole obligation: provided that the nonconforming or defective goods are rejected in writing (including a reasonable
failure analysis statement) to Hampshire Company and returned to Hampshire Company within the relevant warranty
period and provided that the nonconformance or defect was not caused by misuse, alteration, accident, or abnormal
conditions of storage, operation or handling, as determined by Hampshire Company.
THIS WARRANTY IS YOUR SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, FURTHER, HAMPSHIRE COMPANY SHALL NOT BE LIABLE FOR ANY DIRECT,
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGE OR LOSSES, INCLUDING LOSS OF
PROFITS, BUSINESS INTERRUPTION, OR OTHER PECUNIARY LOSS, WHETHER ARISING FROM BREACH OF
WARRANTY OR BASED ON CONTRACT, FUNDAMENTAL BREACH OR ANY OTHER THEORY. SINCE SOME
JURISDICTIONS DO NOT ALLOW LIMITATIONS OF THE TERMS OF ANY IMPLIED WARRANTY, OR
EXCLUSION OR LIMITATION OF INCIDENTAL OF CONSEQUENTIAL DAMAGES, THE LIMITATIONS AND
EXCLUSIONS OF THIS WARRANTY MAY NOT APPLY TO YOU.
General Information
Mailing address:
World Wide Web:
Support E-Mail Address
Hampshire Company, Inc.
9055 North 51st Street
Suite H
Brown Deer, WI 53223
Phone: 414-355-4675
Fax: 414-355-4775
www.hampshirecompany,com
support@hampshirecompany.com
Copyright Information
This manual is ©1995-2008 Hampshire Company, Inc. Reproduction of the contents of this copyrighted material in
whole or in part, by any means, mechanically or electronic, for any purpose, without the written permission of
Hampshire Company, Inc. is prohibited.
Hampshire Company, Inc., the Hampshire Logo, Hampshire®, TSHARC™, the TSHARC logo, and UniWinDriver™
are Trademarks of Hampshire Company, Inc. Elo and 3M (Microtouch) are trade names of Tyco Electronics and 3M
Company respectively. All Rights Reserved.
Edition Information
Printed on:
Document Part number:
November 21, 2008
08B_TSHARC_C-Ray_Users_Rev3.3x_081121.doc
3
Product Description
The TSHARC C-Ray Board is a new standard in capacitive touch screen controller technology. It supports serial and
USB communication as well as all manufacturers’ capacitive touch screens regardless of whether or not the screen
includes a back shield.
The C-Ray is a high-performance touch screen controller which, in holding true to Hampshire’s design fundamentals,
utilizes ‘off-the-shelf’ microcontroller technology in conjunction with Hampshire’s proprietary decoding techniques and
device driver software. This virtually eliminates the threat of obsolescence while maintaining the high-performance
and utility standards expected from Hampshire Company.
Hampshire’s own TSHARC device drivers are included with the chip or board solutions. Bill-Of-Materials schematic
drawings and technical support are available for chip applications. Custom and private-labeled hardware and
software products are also available.
Part Number Information
HS12-009C0J-03
The latest firmware revision will be supplied with all TSHARC C-Ray capacitive boards ordered.
Integrating the TSHARC Capacitive Controller
Mounting the Controller
The controller has two .122” diameter (4-40 or 3mm screw) plated mounting holes. Notice the mounting hole closest
to the touch screen connector H4. THIS STATIC GROUND MOUNT MUST TERMINATE TO A STATIC GROUND.
Failure to ground the controller will result in poor performance and may eliminate the effectiveness of the on board
static protection. Please refer to Fig. 4.0 for mounting details. For additional details about controller integration,
please contact Hampshire.
For best performance mount the controller:
1)
In such a way to keep the touch screen tail away from high EMI, RFI and power sources.
2)
“In line” with the touch screen tail limiting the number and severity of any bends or folds in the touch screen
tail.
Contact your touch screen manufacturer to determine any touch screen manufacturer’s mounting
specifications.
3)
In a way to insure that you are using a communication cable with adequate shielding which is located away
from high EMI, RFI radiating system components.
4)
To shield the controller and/or the touch screen from EMI / RFI noise in cases where required. Mounting the
controller into a metal box which is shielded might be necessary.
5)
To insure the back shielded touch screen terminates to pin #3 (center pin) of H4. It is required if a back
shield is available.
6)
Make sure the back shield of the sensor does not come in contact with any grounded part of the system.
IF PIN #3 IS CONNECTED IN ANY WAY TO AN EXTERNAL GROUND, YOU MAY PERMANENTLY
DAMAGE YOUR CONTROLLER BOARD.
7)
Such that the board, the LCD, and the computer system all have the same ground. Failure to have the
same ground throughout the system may result in reduced controller performance.
8)
The static ground mount must be terminated to a static ground before powering on the controller board.
Failure to follow this procedure will bypass the static protection and may damage the controller causing the
board to not function properly.
Figure 4.0: Controller Mounting Diagram
Mounting Holes
2 plcs. .122" dia 4-40 screw (3mm)
H1
HAMPSHIRE
HSC2009SIJ
C2S4B0726
H3
H2-A
+
H1-A
H2
Required STATIC ground mount
.122" Dia. 4-40 (3mm)
4
Mounting the Capacitive Touch Screen
There are a number of methods that may be used to mount your touch screen depending upon your application and
the recommendations of your sensor supplier. In all cases it is important that you do not make any electrical
connections between the touch sensor and the integrated system. Please contact your sensor manufacturer for
specific mounting recommendations.
The sensor tail often experiences more electrical noise than the sensor itself. Special care should be taken when
considering the tail mounting of the sensor. Please contact your sensor manufacturer for specific instructions
regarding the sensor tail.
In all cases, take special care to mount the touch screen in such a manner as to eliminate any screen shift or
movement during operation. The C-Ray controller gathers environmental variables at power-up. Any changes to the
touch screen position during use can negatively influence the performance of the system.
Connecting the Touch Screen
The TSHARC C-Ray, capacitive controller supports back shielded, non-back shielded and shielded tail capacitive
touch screen overlays. Check the touch screen tail and verify the pin-out of the touch screen before you connect the
touch screen to the controller. If the touch screen has a back shield or a shielded tail a connection must be made to
the 3rd pin of header H4. Failure to connect a shielded touch screen or tail will cause the controller to malfunction.
This connection is shown in Fig. 5.0.
Note: Hampshire’s touch screen mapping is consistent with all operating system display mapping specifications. Most operating
systems draw the screen from upper left to lower right. If you are using the controller in a 3M® (Microtouch™ 5 - Byte emulation)
mode, the touch screen connection may not be consistent with this mapping protocol. In some cases, 3M™ maps the screen from
lower left to upper right which is 180 degrees rotated from Microsoft standard. For 5-byte Emulation mode the touch screen
connection will be as follows: UL, UR, Shield, LR, LL. Contact Hampshire for pin-out compatibility solutions.
NOTE: Hampshire does not recommend that you use the controller in a Microtouch™ emulation mode on any forward moving
products. This tool is designed to be used for migrating from Microtouch™ to Hampshire™ standard products.
!! Hampshire device driver software will correct for Microtouch™ touch screen orientation via the TSHARC calibration software.
There is no need to change the Microtouch™ touch screen connections in order to use the Hampshire’s native controller
configuration with a Hampshire driver. If you have developed your own driver or are using raw data from the controller you must
connect the touch screen to the controller as identified below.
Figure 5.0: Touch Screen Connection Diagram
Touch Screen Connection Diagram
H1
HAMPSHIRE
HSC2009SIJ
C2S4B0726
H3
H2-A
+
H1-A
TopRight
TopLeft
Back Shield
LowLeft
LowRight
Capacitive Touch Screen
If no back shield consctruction do not
connect center "back shield" connection.
H2
Required STATIC ground mount
.122" Dia. 4-40 (3mm)
5
Communication Jumper Configurations
The TSHARC Capacitive controller supports RS-232 and USB, HID compliant, low speed, communication. While
these are Hampshire’s standard communication formats, custom communications are available.
Please refer to Fig. 6.0 for the jumper configurations that may be implemented.
Figure 6.0: Jumper Selectable Communications
Mounting Hole, One of Two
.122" dia. 4-40 (3mm)
+
+ Pwr -
H1
POWER
GROUND
HAMPSHIRE
HSC2009SIJ
C2S4B0726
1
H3
H2-A
H1-A
J1
Mounting Hole, One of Two
.122" dia. 4-40 (3mm)
2.185"
H2
Hampshire Standard
HS12-049COJ-03
USB
RS-232
Connecting the C-Ray for RS-232 Communication
Before connecting the RS-232 communication cable, check the jumper setting on the board to insure that it
is set properly for RS-232 communication.
Figure 6.1: RS-232 Cable Connection Diagram
Mounting Holes
2 plcs. .122" dia 4-40 screw (3mm)
Communication
Header
5
1
5 - Gnd
HAMPSHIRE
HSC2009SIJ
C2S4B0726
9
USB
H3
H2-A
3 - Txd
2 - Rxd
6
1
H2
H1
+ Pwr -
Pwr
Gnd
+
+5vDC or 7.5 - 24vDC
H1-A
H2
Txd transmit to board
Rxd transmit from board
Jumper as shown is set
for Hampshire RS-232
Remove for USB operation
Required STATIC ground mount
.122" Dia. 4-40 (3mm)
.
The RS-232 communication cable can be connected to the controller using a variety of cable types. Part number
C72-100S2F-09XDXF cable may be sourced directly from Hampshire Company. This is a standard 6’ long DB-9
female connector terminated to a (housing/contact) 10 position dual row socket via a round shielded cable. This
cable has a ground shield termination wire running the length of the cable which must be terminated to earth ground.
Not terminating the cable shield will have a negative effect on the controller’s performance.
Should a self-built cable be required, a 10-position, dual-row socket contact/housing connector type may be used to
connect the RS-232 communication header. If an IDC connector type is desired, a 14-position socket can be used,
which extends on to the USB pins with only the RS-232 communication connections terminated. A 10-position IDC
socket cannot be used for connecting to the communication header because the width of an IDC socket is too wide to
fit between the USB connection pins and the pins needed for RS-232 communication.
Hampshire also provides the option to use a single row, 2.0 mm, 7-pin connection to the serial communication
connection of the TSHARC-C controller board. This option may be used if it is desired to continue to connect the
TSHARC-C controller to your system which has already been configured for 3M™ Microtouch™ connections. Please
contact Hampshire for ordering instructions regarding this option.
6
Connecting the C-Ray for USB Communications
Take special care when connecting the USB cable. Incorrect pin selection using the USB cable will result in
a failed board when attempting to power the board. Also, be sure the jumpers are configured the way
required for USB performance.
Connect the USB header contacts as shown in Fig. 7.0 for enabling USB communications with the controller board.
The USB contacts are located on the lower side of the communication header. A 6’ long 4-position socket to a Type
“A” USB plug jacketed and shielded USB cable, part number C72-040S1F-04XAXM from Hampshire Company, Inc
can be ordered. This particular cable has a ground shield termination wire running the length of the cable which must
be terminated to earth ground. Not terminating the cable shield will have a negative effect on the controller’s
performance. For information about ordering this cable, please contact Hampshire Company, Inc.
Special Note: If planning to use a USB-hub, then it is critical to use a hub which has externally supplied power. If
multiple devices are attached to the hub, then be sure the hub has sufficient power to power all devices connected.
Failure to follow this recommendation will cause the controller to fail during operation.
Figure 7.0: USB Cable Connection Diagram
USB Communication Header
Ground contacts 2-pls allows for polorization
of 5pos USB connector
PinOut
1 (Gnd)
2 (D+)
3 (D-)
4 (Pwr)
H3
HAMPSHIRE
HSC2009SIJ
C2S4B0726
Pinout
4
3
2
1
H2-A
H1
+
Do not connect power pin on USB if
connecting external power on H2
H1-A
H2
Do not place jumper for USB communication
Required STATIC ground mount
.122" Dia. 4-40 (3mm)
There is an extra ground pin for USB which may be used to connect a five position USB connector. A five pin
connection may be required if polarization of the connector is desired to insure it is terminated correctly.
Additional Connection Information
Communication Connector
UL and part number information can also be found in Fig. 10.0.
Touch Screen: Amp 103635-4
Communication: .100” Sullins: PEC05DBAN & PEC02SBAN
Mounting Hardware
Due to the wide variety of mounting options available for the TSHARC capacitive board, we do not stock mounting
hardware. Please visit the RAF web site to review the available mounting hardware.
http://www.rafhdwe.com/RAF_site/OnlineCatalog/EHCoverFrame.html
TSHARC Controller Chip Solutions
Large volume OEM’s who have in-house electrical and software engineers on staff may purchase a Hampshire “Chip
Only” touch screen controller solution which may be integrated on to their main board. A complete set of technical
documentation is available from Hampshire Company to assist in correctly integrating a chip solution into a product.
Please contact Hampshire Company, Inc. for additional information.
7
Communication Protocol
All Hampshire touch screen controllers communicate with the host computer in a 4-byte communication protocol.
Hampshire’s 4-byte communication protocol produces the industry’s most reliable and accurate data transfer
information without compromising touch speed.
Note: Many Hampshire controllers may be configured to communicate with other industry protocols such as 3M’s 5-Byte or
Elotouch™ 10-byte communication protocol. However, the overall performance of the Hampshire controller will then be limited to
that standard’s level of performance. In no case does Hampshire authorize the use of any driver software, other than Hampshire
device drivers or a Windows HID driver, to enable a Hampshire controller without proper authorization from the software developer
or rightful owner of the software.
For information regarding Hampshire’s 3M or Elo migration hardware or software communication protocol, please contact
Hampshire Company, Inc. Elo and 3M (Microtouch) are trade names of Tyco Electronics and 3M Company respectively. All Rights
Reserved.
Table 8.0: Hampshire standard USB Protocol
Byte
1
2
3
4
5
Bit 7
0
X7
0
Y7
0
Bit 6
0
X6
0
Y6
0
Bit 5
0
X5
0
Y5
0
Bit 4
0
X4
0
Y4
0
Bit 3
0
X3
X11
Y3
Y11
Bit 2
0
X2
X10
Y2
Y10
Bit 1
0
X1
X9
Y1
Y9
Bit 0
P
X0
X8
Y0
Y8
Bit 3
X9
X5
Y5
X1
Bit 2
Y11
X4
Y4
X0
Bit 1
Y10
X3
Y3
Y1
Bit 0
Y9
X2
Y2
Y0
Table 8.1: Hampshire standard RS-232 Protocol
Byte
1
2
3
4
Where:
Bit 7
1
0
0
0
Bit 6
P
X8
Y8
0
P
X11-X0
Y11-Y0
Bit 5
X11
X7
Y7
0
Bit 4
X10
X6
Y6
0
- 0 Pen-Up, 1 Pen-Down
- 12 bit X position data
- 12 bit Y position data
Powering Your System
Before applying power to your system, please check all cables are tightly connected and verify the mounting of the
controller and sensor. If powering the controller using USB, the system power should be brought up at the same
time.
If using an external power supply, please be certain that the monitor is activated before the controller is turned on.
The environmental baseline is taken at power-up, and performance could be affected if the monitor is not present
when the controller is powered on.
Static Protection Warning
The TSHARC C-Ray controller has internal static protection to +/- 30kV for static discharge from the touch screen to
the controller. This static protection is only effective once the board is grounded properly. Adequate static
precautions must be taken when connecting the TSHARC controller to the application. In some applications, it may
be necessary to further protect your controller board from excess transient voltage. If it is believed that the
application will require additional static protection, the appropriate static protection needed to protect the electronics
from transient voltage is up to the customer. Failure to take the necessary precautions may result in damage to
your controller. Hampshire does not warrantee the board for static voltage damage.
For additional information about Hampshire’s ESD testing procedures, please contact Hampshire Company.
Email: support@hampshirecompany.com
Telephone: (414) 355-4675
Status LED Indicator
The TSHARC C-Ray capacitive touch screen controller board is equipped with a status-indicator Light Emitting Diode
(LED). This LED will give you information regarding the functionality of the controller. The LED indication codes are
as follows:
When powered on: The LED with blink once (on then off), collect an environment baseline then
blink once again for 1 second. DO NOT TOUCH THE TOUCH SCREEN DURING THIS
PROCESS.
Every time the touch screen is touched: Once the controller has collected the baseline, the LED
will turn off. It will turn on every time the operator touches the touch screen thereafter.
DO NOT TOUCH THE TOUCH SCREEN IMMEDIATELY AFTER THE CONTROLLER IS POWERED ON. THE
CONTROLLER MUST COMPLETE THE BASELINE PROCESS IN ORDER TO POWER ON CORRECTLY.
8
Software Device Drivers
Hampshire Company has device driver software available for all TSHARC touch screen controller chip and board
solutions. The software drivers may be downloaded at no additional charge at: www.hampshirecompany.com .
Reported Hampshire resolution is dependent upon the hardware A-D converter specification. Hampshire device
driver software is designed to deliver true 10 or 12 bit hardware resolution respective to the touch screen controller
hardware.
The TSHARC device driver software enables you to configure the touch screen operation to meet your needs. The
following is a list of features available with Hampshire’s software:
1)
Touch screen calibration
2)
Touch screen linearization
3)
Touch screen alignment
4)
Multi-monitor calibration and configuration
5)
Adjustable calibration inset
6)
Edge acceleration
7)
Touch modes
a. Normal mouse emulation
b. Touch Up mode
c. Touch Down mode
8)
User adjustable Configurations
a. Hampshire proprietary touch screen friendly timed right click event
b. Touch event area setting
c. Touch sound enable / disable
9)
Other special features also included. Please see the complete driver manuals available at
the www.hampshirecompany.com web site for further details.
Note: TSHARC device drivers vary between operating systems and operating system varieties and versions.
Currently Hampshire supports the following Windows® Operating systems: DOS, Win3.1x, 9x, ME, Xp, XPe, 2k, CE,
CENet, Tablet. TSHARC driver for Linux, and MAC are also included with all TSHARC touch screen controller
products.
Additional utilities may be available for use. Please contact Hampshire Company for additional information.
Saving Calibration to EEPROM
The firmware included on this board is able to store calibration data to the controller’s EEPROM.
Additional utilities are available to utilize this feature. Please contact Hampshire Company for additional information.
Hampshire Support Services
All of Hampshire products are 100% developed and supported in house by Hampshire technical staff. As a result, we
have included a broad range of support documentation on the Hampshire web site www.hampshirecompany.com
including users and setup manuals, device drivers, driver manuals, and other software. In addition, we have an e-mail
based support. Please contact us via e-mail at: support@hampshirecompany.com. Hampshire also understands
that there is often a need for “real time” technical support. Please contact Hampshire via telephone at any point to
discuss issues that you may have regarding our products. Hampshire’s telephone number: 414-355-4675.
In the event that you need to contact us via telephone or our support e-mail, please take a moment to complete our
“On Line” support form which is available on our web site: www.hampshirecompany.com.
Completing this form prior to contacting Hampshire will insure a prompt response from our technical staff. If the online form is not completed, our technical staff will ask you for the following details of the application.
Please take a minute to identify these items prior to contacting Hampshire technical support staff.
1)
Hampshire controller part number
2)
Information about Hampshire reseller if not purchased directly from Hampshire
3)
Hampshire chip revision (located on the top of each micro-controller chip)
4)
Touch Screen type and Manufacturer
5)
Communication type
6)
TSHARC driver and revision
7)
Operating system and service pack releases
8)
A brief summary of the problem experienced.
9
Appendix
Product Specifications
Touch Screen:
Resolution:
Communications:
Com Protocol:
Size:
All Capacitive touch screens with or w/o back shield
12 Bit (4,096 x 4,096)
RS-232 and USB
HID Compliant USB and Hampshire Standard serial
2.43” x 1.30”
Connectors
Touch Screen Side:
Com Side:
Amp 103635-4
.100” Sullins: PEC05DBAN & PEC02SBAN
Sample Rate:
Baud Rate:
Voltage Required:
Environmental:
Static Protection:
PC Board UL File:
Connectors UL File:
Part Number:
Configurable 40 - 100 points/sec. (raw data >240 points/sec.)
9600 baud (others available upon request)
5Vdc– 16Vdc +/- 5% or from USB port
Storage: -65°C – 150°C Operating: -40°C – 70°c
30 KVA
See Fig. 5.0
See Fig. 5.0
HS12-009C0J-03
Mechanical Diagram
Figure 10.0: Mechanical Diagram of TSHARC C-Ray Touch Screen Controller Board
Mount holes 2 places
.122" Dia. 4-40 or 3mm screw.
2.435"
2.010"
Connector
Sullins: PEC02SBAN
UL# E64287
H3
H2-A
.100"
.350"
H1
H1-A
Connector
AMP: 103635-4
UL# E28476
.160"
REQUIRED STATIC ground
mount .122" Dia. 4-40 (3mm)
.125"
H2
.050"
Connector
Sullins: PEC02SBAN
UL# E64287
+
.100"
.450"
1.300"
1.175"
.165"
.165"
.343"
2.310"
.175"
.100"
HAMPSHIRE
HSC2009SIJ
C2S4B0726
Connector
Sullins: PEC05DBAN
UL# E64287
UL# E28476
.125"
NOTE!! The board revision number can be found on a label on the back side of your controller board. The
firmware revision number may be found on a label or a laser mark located on the TSHARC microcontroller chip.
10
R
1
5
5 - Gnd
3 - TX
2 - Rxd
Gnd
D+
D+5vDC
H a m p s h i r e C o m p a n y, I n c .
9055 N 51st Street Suite: H
Brown Deer, WI 53223 USA
Step 5
Connect Power
Power
Ground
TX
Rxd
Gnd
USB
STEP 3
Connect Touch
Screen
Step 1
Set Communication
Type
H3
H3
H2
H1
Step 2
Mount Controller
H1-A
RS-232
Use a jacketed - shielded
touch screen cable for
best performance
Required STATIC ground mount
.122" Dia. 4-40 (3mm)
Top right
Top Left
Back Shield
Bottom Left
Bottom Right
Follow these steps:
1) Set Communication type
2) Mount Controller
3) Connect Touch Screen
4) Connect Communication Cable
5) Connect Power
6) Turn on Computer
7) Install TSHARC drivers
USB
Hampshire Standard
HS12-009COJ-03
H2-A
C-Ray Quick View Kit Assembly Diagram
Gnd
Gnd
D+
D+5vDC
RS-232
Phone: 414-355-4675
Fax: 414-355-4775
w w w.h a m p s h i r e c o m p a n y.c o m
Hampshire Communication Cable
RS-232 Cable: C72-100S2F-09XDXF
USB Cable: C72-040S1F-04XAXM
6
9
Gnd 4
D+ 3
2
D+5vDC1
Step 4
Connect Communication Cable.
If using external power at positions H2 for USB,
DO NOT CONNECT the USB power pin #8 (+5vDC)
COMPANY
TM
Hampshire TSHARC
HAMPSHIRE
HSC2009SIJ
C2S4B0726
HAMPSHIRE
Quick View Setup
Figure 11.0: Quick View Setup Diagram
+
11
Cables Available from Hampshire
Table 12.0: Available Communication Cables
Part Number:
C72-100S2F-09XDXF
Description:
6’ RS-232 cable. Direct connect H1 header to female DB-9
C72-040S1F-04XAXM
6’ USB cable. Direct connect H3 header to male type-A plug connector
Table 12.1: Available Power Cables
C20-020S1F-XXXXX
20” power cable, Direct connect to H2. 2 position, .100” socket to wire lead.
C20-020S1F-020S1F
20” power cable, Direct connect to H2. 2 position, .100” socket to 2 position .100” socket
12
NOTES
Copyright Hampshire Company, Inc. 1995 – 2008
Hampshire®, TSHARC™ and UniWInDriver™ are trademarks of Hampshire Company, Inc.
All rights reserved.
13
Open as PDF
Similar pages