OWNERS MANUAL
E N G I N E E R E D W I T H T H I N P L AT E P U R E L E A D ( T P P L ) T E C H N O L O G Y
EXTREME POWER
AND ENDURANCE
www.odysseybattery.com
www.enersys.com
INTRODUCTION
The ODYSSEY® battery ingeniously uses absorbed glass mat (AGM) technology to offer, in one box, the
characteristics of two separate batteries. It can deep cycle as well as provide enormous cranking power –
it is almost as if a champion long distance runner and a world class sprinter are one and the same person.
These batteries are capable of providing engine cranking pulses in excess of 2250A for 5 seconds as well as 400
charge/discharge cycles to 80% depth of discharge (DOD). A typical starting, lighting and ignition (SLI) battery can
do one or the other, but not both. It is either a sprinter or a long distance runner; ODYSSEY batteries will do both –
provide short duration high amperage pulse or low rate long duration drains.
In order to achieve the full design cycle life of ODYSSEY batteries in cyclic applications the charge current must be
a minimum of 40% of the battery’s 10-hour rating (column 8 of the chart on page 5). Thus the minimum charge
current for a PC925 battery in a cycling application is 10.8 amps (40% of 27Ah). Please refer to Figure 6 of the
ODYSSEY Technical Manual for a detailed discussion of the recommended charge profile for ODYSSEY batteries in
cycling applications. The manual may be downloaded from www.odysseybattery.com.
WHY USE ODYSSEY® BATTERIES?
GUARANTEED LONGER SERVICE LIFE
With an eight to twelve year design life (float) and a three to ten year service life, ODYSSEY batteries save you
time and money because you do not have to replace the battery as often. Since actual warranty can vary with your
geographical location, please check with your ODYSSEY Extreme Series battery representative for the warranty
specific to your application.
SUPERIOR CRANKING AND FAST CHARGE CAPABILITY
The 5 second cranking power of ODYSSEY batteries is double to triple that of equally sized conventional batteries,
even when the temperature is as low as -40°C. Also, with simple constant voltage charging (alternator or independent
charger), there is no limitation on the inrush current, so the user is assured of fast charge recovery.
MOUNTING FLEXIBILITY
The ODYSSEY battery may be installed in any orientation (except inverted) without sacrificing any performance
attributes. There is no fear of any acid spillage as ODYSSEY batteries recycle the internal gas during operation or
charging. The valve regulated design of the ODYSSEY battery eliminates the need for an acid vent tube; eliminating
the fear of acid burns or damage to expensive chrome or paint.
SUPERIOR VIBRATION RESISTANCE
ODYSSEY batteries have endured rigorous tests that demonstrate their overall ruggedness and exceptional tolerance
of mechanical abuse.
READY OUT OF THE BOX
ODYSSEY batteries are shipped fully charged. If the ODYSSEY battery's voltage is 12.65V or greater, simply install
the battery in your vehicle and you are ready to go! If below 12.65V, boost charge following the instructions in the
ODYSSEY battery Owner’s Manual and/or Technical Manual. Putting a boost on the battery will not damage it,
even if its voltage reads higher than 12.65V.
WORRY-FREE SHIPPING
Owing to the drycell design, the US Department of Transportation (USDOT) has classified the ODYSSEY battery as
nonspillable, so it may be shipped worry-free by express service or by air.
LONGER STORAGE LIFE
Unlike conventional batteries that require a recharge every six to twelve weeks, the ODYSSEY battery can be stored
for up to two years at 25ºC from a fully charged state. These batteries can be stored for two years or when the open
circuit voltage (OCV) drops to 12.00V, whichever comes first.
DEEP DISCHARGE RECOVERY
Should the ODYSSEY battery become deeply discharged, simply recharge following instructions in this manual.
2
www.odysseybattery.com
www.enersys.com
INSTALLATION
Your ODYSSEY® battery is normally ready to install right out of the box! Measure the battery voltage; if it is 12.65 volts
or greater, install; if less, then refer to the charging section.
ANY OF THE FOLLOWING WILL VOID YOUR WARRANTY:
• EXPOSING BATTERY TO OIL, ORGANIC SOLVENT, ALCOHOL, DETERGENT, STRONG ACIDS, STRONG
ALKALIS, PETROLEUM-BASED SOLVENT OR AMMONIA SOLUTIONS
• REMOVING THE LABELED COVER
• REMOVING OR DESTROYING THE BATTERY’S DATE CODE
DO NOT SHORT CIRCUIT YOUR ODYSSEY® BATTERY'S TERMINALS!
Remove any metallic items such as watches, bracelets and other personal jewelry to ensure safe installation.
ALL OTHER MODELS
PC370, PC950 & PC1100
A
C
A. Bolt
B. Washer
C. Battery
1.0mm
13.5mm
NTS
16.0mm
SAE TERMINALS
C
PC2250
A. Brass Post
B. Helicoil Insert
C. Accessory Bolt
B
17.0mm
19.5mm
7.9mm
NEGATIVE
D
15.6mm
NTS
18.6mm
20.7mm
3/8-16 UNC-2B
8.6mm DEEP
20.7mm
NEGATIVE
POSITIVE
TOP TERMINALS
B
17.2mm
18.6mm
A. 18.2mm MAX
B. 24.5mm MAX
75/86-PC1230
34/78-PC1500
17.2mm
18.6mm
34R-PC1500
3/8-16 UNC THREAD
A
A
POSITIVE
DIN TERMINAL
15.6mm
3/8-16 Course Thread
(not included)
D. Battery
17.0mm
75/86-PC1230
25-PC1400
35-PC1400
34-PC1500
34/78-PC1500
65-PC1750
31-PC2150T
M10
18.8mm
11.0mm
PC1220 & PC1350
17.5mm
FRONT TERMINAL
25.4mm
NOTE:
PC535 and PC625 Bolt installations
are in horizontal orientation.
1.0mm
PC1800-FT
31-PC2150S
3/8-16 UNC
THREAD
M6 x 1
THREAD
B
18.6mm
20.7mm
20.7mm
POSITIVE
NEGATIVE
34M-PC1500 & 31M-PC2150
POSITIVE MARINE STUD
3/8-16 THREAD
POSITIVE SAE
TERMINAL
18.59mm
14.43mm
NEGATIVE MARINE STUD
5/16-18 UNC THREAD
NEGATIVE SAE
TERMINAL
14.43mm
18.59mm
21.59mm
28.44mm
SIDE TERMINAL
NOTE: See SAE terminal drawing for detailed dimensions
1. Using proper procedures as recommended by the vehicle manufacturer, carefully disconnect the cables from
your old battery and remove it from the vehicle. Return the spent battery to the battery dealer for proper recycling.
2. Inspect existing battery cables for corrosion, acid damage or insulation deterioration. Replace if deterioration
is present.
3. Position your ODYSSEY battery in the battery holder and fasten firmly to the vehicle.
• Optional height adapter may be used on 34-PC1500 models for installations
where a group 24 or group 27 is required. Snap the adapter securely into place on the
bottom of the battery. In some installations the 34R-PC1500 model with this adapter may
be used to replace a group 24F or 27F depending on required cable length.
4. Connect the positive cable from your ignition to the Positive (+) terminal.
5. Connect the negative cable from your engine or chassis to the Negative (-) terminal.
6. Torque the bolt, screw or nut per the specification noted in table. If you’re using the Accessory Bolt (C), hold the
Brass Post (A) with vise grips and counter torque. Do the same with General Motors® automotive battery cable
installation.
NOTE: This is a valve regulated sealed battery and never needs to have water or electrolyte (acid) added.
Warranty will be void if opened!
www.odysseybattery.com
www.enersys.com
3
SPECIAL NOTICE!
• CUSTOM V-TWIN MOTORCYCLE INSTALLATIONS USING ODYSSEY PC535, PC545, PC545MJ, PC680MJ
& PC925LMJ BATTERIES
If your V-Twin motorcycle is equipped with a standard 32 amp single phase stator/alternator and you ride at a low
engine rpm around town or even on long rides, the appropriate ODYSSEY® battery may run out of charge due to
low amperage output of the bike's stator at low rpms. After riding, turn the bike's engine off but leave the lights on
for 30 seconds. Then, turn everything off and connect to a suitable charger.
• Prolonged storage of vehicles with fuel injection computers, alarms, GPS and other electrical devices that require
continuous battery power to support active memories; this power drain must be offset with a maintenance-float
charger, periodic charging or disconnecting the battery to prevent the establishment of irreversible crystallized
sulphation in the battery plate oxide. Failure to address this destroys battery capacity and voids the warranty,
as this is not a warranted defect in materials or workmanship.
ODYSSEY® BATTERY STORAGE AND DEEP DISCHARGE RECOVERY
Figure 2 shows the relationship between open
circuit voltage (OCV) and state of charge (SOC)
for the ODYSSEY battery.
(A) How do I know the state of charge of the
battery?
Refer to Figure 3 below. At 25ºC, these batteries
can be stored for up to 2 years. The lower the
temperature, the longer the storage time.
The battery must be charged before storage.
Roughly every 10°C increase in temperature cuts
storage time in half. If the temperature rises to 35°C
the battery may be stored for only 1 year before a
recharge becomes necessary. Figure 3 will apply only
if the battery is fully charged before storage.
13.0
12.84V or higher indicates
100% SOC
12.8
12.6
12.4
12.2
100
12.0
25°C
45°C
65°C
90
11.8
11.6
10
20
30
40
50
60
70
80
90
100
State of Charge (SOC), %
Figure 2: ODYSSEY Battery OCV vs. SOC
Percent of 0.05C capacity
Open circuit voltage (OCV), V
(B) How long can the battery be stored?
80
70
60
50
40
As long as the battery has not been charged or
discharged for 6 or more hours, Figure 2 can be
used to determine the SOC of the ODYSSEY battery.
Use a high quality digital voltmeter to measure its
OCV. The graph shows that a healthy, fully charged
ODYSSEY battery will have an OCV of 12.84V or
higher at 25ºC.
4
www.odysseybattery.com
30
0
10
20
30
40
50
60
70
Open circuit storage time in weeks
Figure 3: ODYSSEY Battery storage
time at temperatures
www.enersys.com
*Cold Start Performance S.A.E J537 JUNE 82
**Pulse Current
† Can be fitted with brass automotive terminal
Optional metal jackets available on available on PC545, PC680, PC925, PC1200, PC1700 and 31-PC2150
Operating Temperature Range:
PC310, PC370, PC950, PC1100 and PC1800-FT: -40°C to 50°C,
PC535 and PC625: -40°C to 45°C,
PC545, PC680, PC925, PC1200 and PC1700 without metal jacket: -40°C to 45°C,
PC545, PC680, PC925, PC1200 and PC1700 with metal jacket: -40°C to 80°C,
PC1220, PC1350 and PC2250: -40°C to 40°C,
All other models: -40°C to 80°C
†† Height may include SAE/DIN terminal, metal jacket and maximum tolerance
Nominal Capacity
Model
Voltage
PHCA**
(5 sec)
CCA*
HCA MCA
20 Hr
Rate-Ah
10 Hr
Rate-Ah
Reserve
Capacity
Minutes
Length
mm
Width
mm
Height††
mm
Weight
kg
Terminal
Torque
Specs
Nm max
Internal
Resistance
(mΩ)
Short
Circuit
Current
PC310
12
310
100
200 155
8
7
9
137.5
86.0
99.0
2.7
M4 Receptacle
1.0
27.1
455A
PC370
12
425
200
315 270
15
14
25
200.0
77.0
140.0
5.7
M6 Stud
3.9
13.5
891A
PC535
12
535
200
300 265
14
13
21
170.2
99.1
158.5
5.4
M6 Receptacle
4.5
8
1000A
PC545
12
460
150
280 220
13
12
18
177.8
85.9
131.3
5.2
M6 Receptacle
5.6
10
1200A
PC625
12
530
200
420 340
18
17
27
170.2
99.1
176.5
6.0
M6 Receptacle
4.5
7
1800A
5.6
7
1800A
or SAE
3/8” Receptacle
6.8
5
2400A
M6 Receptacle†
or SAE
3/8” Receptacle
M6 Receptacle†
PC680
12
520
170
350 280
16
16
24
184.7
79.0
191.8
7.0
PC925
12
900
330
610 480
28
27
48
168.7
179.1
148.1
11.8
PC950
12
950
400
600 500
34
32
60
250.0
97.0
156.0
9.0
M6 Stud
3.9
7.1
1700A
PC1100
12
1100
500
800 650
45
43
87
250.0
97.0
206.0
12.5
M6 Stud
3.9
5.1
2450A
6.8
4.5
2600A
PC1200
12
1200
540
860 725
42
40
78
199.9
169.2
193.0
17.4
M6 Receptacle†
or SAE
3/8” Receptacle
PC1220
12
1220
680
960 860
70
64.8
135
278.0
175.0
190.0
20.7
DIN Lead Post
N/A
5.7
2200A
75/86PC1230
12
1230
760
1050 815
55
50
110
240.3
179.8
201.2
20.6
TOP SAE SIDE
3/8” Receptacle
6.8
2.5
3100A
PC1350
12
1350
770
1080 960
95
88.5
195
353.0
175.0
190.0
27.4
DIN Lead Post
N/A
4.2
2900A
25-PC1400
12
1400
850
1150 950
65
55
130
240.3
173.7
220.7
22.7
SAE
6.8
2.5
3100A
35-PC1400
12
1400
850
1150 950
65
55
130
240.3
173.7
220.7
22.7
SAE
6.8
2.5
3100A
34-PC1500
12
1500
850
1250 1050
68
62
135
275.6
171.7
200.2
22.4
SAE
6.8
2.5
3100A
34R-PC1500
12
1500
850
1250 1050
68
62
135
275.6
171.7
200.2
22.4
SAE
6.8
2.5
3100A
6.8
2.5
3100A
34M-PC1500
12
1500
850
1250 1050
68
62
135
275.6
171.7
201.9
22.4
SAE and
3/8” Stud (Pos.),
5/16” Stud (Neg.)
34/78PC1500
12
1500
850
1250 1050
68
62
135
275.6
179.8
200.2
22.4
TOP SAE SIDE
3/8” Receptacle
6.8
2.5
3100A
PC1700
12
1550
810
1325 1175
68
65
142
331.0
168.4
197.6
27.6
M6 Receptacle†
or SAE
3/8” Receptacle
6.8
3.5
3500A
65-PC1750
12
1750
950
1350 1070
74
65
145
300.5
182.9
190.5
26.3
SAE
6.8
2.0
5000A
PC1800-FT
12
1800
1300 1600 1450
214
190
475
581.0
125.0
316.5
60.0
M10 Stud
9.0
3.3
3800A
35.3
3/8” Stud or
SAE†
31-PC2150
12
2150
1150 1545 1370
100
92
205
331.7
175.0
243.6
31M-PC2150
12
2150
1150 1545 1370
100
92
205
330.2
172.7
238.5
35.3
PC2250
12
2250
1225 1730 1550
126
114
240
286.0
269.0
233.0
39.0
www.odysseybattery.com
16.9-22.6
2.2
5000A
SAE and
3/8” Stud (Pos.), 16.9-22.6
5/16” Stud (Neg.)
2.2
5000A
11.0
For 3/8”
Stud
Only
2.1
5000A
DIN Terminal
and 3/8” Stud
www.enersys.com
5
MAINTENANCE
ODYSSEY® batteries are very different from standard liquid-acid batteries that are openly vented. The ODYSSEY
battery is and operates as a sealed battery, recycling nearly all gases internally under normal operating conditions.
There is no corrosion of the positive terminal or corrosion to the surrounding area. ODYSSEY batteries are shipped
fully charged from the factory, but prior to installation, check the battery’s voltage to see if it is 12.65 volts or greater. If
not, recharge it using the procedure below.
Do not charge in an air tight compartment
Never attempt to remove the top decal cover, as it will cause the battery to fail.
CHARGING
The state of charge in an ODYSSEY battery can be determined from the following chart:
Voltmeter Reading
State of Charge
12.84 Volts or higher
100%
12.50 Volts
75%
12.18 Volts
50%
11.88 Volts
25%
To get long life from the ODYSSEY battery, it is important that the battery is kept near full charge, approximately
12.8 volts. If there are electrical loads during storage, then the negative battery cable should be disconnected or an
independent float charger used. Low power float/maintenance chargers will keep a fully charged battery fully charged
but cannot recharge if the ODYSSEY battery becomes discharged.
Racing Vehicles using total loss (no alternator) - standard automotive type chargers are not designed to return
105-108% of the energy removed. They normally boost charge to 80-95% and expect the alternator to complete the
charge.
To fully charge a 31-PC2150 battery that is routinely discharged deeply, a minimum of 40 amps are required with
charger voltage within the range of 14.1V to 14.7V. It is imperative not to exceed 15.0V as this will cause the pressure
valves to open and out-gas hydrogen, oxygen and water from inside the battery. This will shorten the life of the
battery and cause premature failure. Some portable chargers exceed 15.0V, especially two-wheel garage chargers, so
charging voltages should be verified by measuring the charging voltage during the time when the charging amperage
is reducing from full output. The deep cycle charging voltage must be within 14.1V minimum to 14.7V maximum.
If a standard automotive charger is used to boost charge a discharged battery because of an accessory left on, it is
important to make sure the charging voltage does not exceed 15 volts during charge. A hand held voltmeter can be
used to monitor this periodically. The following chart provides recharge times under this type of boost charging to an
80-95% recharge and then allows the vehicle charging system to complete the charge.
12V PARALLEL CONNECTION
GROUND
BATTERY 2
BATTERY 1
VEHICLE &
CONNECTION
12V MOTOR
6
www.odysseybattery.com
www.enersys.com
24V BATTERY CONNECTION
To power a 24V system, you will need to connect two ODYSSEY® batteries in series. As shown in the top
illustration, below the negative of Battery 1 is wired to the positive of Battery 2.
BATTERY 2
BATTERY 1
24V MOTOR
ODYSSEY® Battery Model
PC310
PC370
PC535
PC545
PC625
PC680
PC925
PC950
PC1100
PC1200
75/86-PC1230
25-PC1400 & 35-PC1400
34-PC1500, 34R-PC1500,
34M-PC1500, 34/78-PC1500
PC1700
PC1220 & 65-PC1750
PC1800-FT
PC1350, 31-PC2150
& 31M-PC2150
PC2250
Charge time for 100% discharged battery (11.5 volts)
10-amp charger
1.28 hours
1.5 hours
2.25 hours
2 hours
3 hours
2.7 hours
4.5 hours
3 hours
4 hours
6.75 hours
9 hours
10.5 hours
20-amp charger
40 minutes
45 minutes
1.25 hours
1 hour
1.5 hours
1.5 hours
2.25 hours
1.5 hours
2 hours
3.5 hours
4.5 hours
5.25 hours
11 hours
5.5 hours
11 hours
11 hours
Not Recommended
5.5 hours
5.5 hours
17 hours
16 hours
8 hours
20 hours
10 hours
WINTER STORAGE
The ODYSSEY battery does not lose its charged energy during cold storage temperatures, so there is no need to
trickle or float charge during winter months. To store off-season, measure the battery voltage to make sure it is fully
charged, 12.84 volts or greater; recharge if necessary. Disconnect the negative battery cable to prevent any applied
electrical load during storage. The ODYSSEY battery cannot freeze down to -40°C, -30°C for PC2250, so it can be
left in the vehicle. It can be stored for 2 years or more below 25°C. Charging is required at 2 years or 12V, whichever
comes first.
A 12V trickle charger with no more than 2% nominal capacity output can also be left connected to the battery if it is kept
in storage for extended periods or if the battery is subject to parasitic loads during storage. The trickle charge voltage
measured at the battery terminals must be between 13.5V and 13.8V.
www.odysseybattery.com
www.enersys.com
7
GENERAL PROVISIONS:
A. Manufacturer has no obligation under the limited warranty herein in the
event the Battery is damaged or destroyed as a result of one for more of
the following:
• Willful abuse, misuse, physical damage, neglect or if the top decorative cover
has been removed.
• Natural forces such as wind, lightning, hail; damage due to fire, collision,
explosion, vandalism, theft, penetration or opening of the Battery case in
any manner.
• Overcharging, undercharging, charging or installing in reverse polarity,
improper maintenance, allowing the Battery to be deeply discharged via a
parasitic load or mishandling of the Battery such as but not limited to using
the terminals for lifting or carrying the Battery. Trickle chargers that do not
have a regulated trickle charge voltage between 13.5V and 13.8V (no lower
than 13.5V and no higher than 13.8V) will cause early failure of the Battery.
Use of such chargers with the Battery will also void the Battery’s warranty.
For applications where an alternator is present, the alternator must deliver
between 14.0V and 14.7V when measured at the Battery’s terminals.
Alternators that do not have a regulated charge between 14.0V and 14.7V
(no lower than 14.0V and no higher than 14.7V) will cause early failure of the
Battery. Use of such alternators with the Battery will also void the Battery’s
warranty.
• Failure to properly install the Battery or lack of metal jacket for high
temperature or vibration applications.
• Repair or attempted repair of the Battery by anyone other than an authorized
Manufacturer’s representative shall void this warranty.
• Normal or accelerated deterioration in the electrical qualities due to operating
or application conditions.
• If the Battery is used for an application that requires higher cranking power
or a greater reserve rating than the Battery is designed to deliver, or the
Battery capacity is less than the Battery capacity specified by the vehicle
manufacturer, or the Battery is otherwise used in applications for which it was
not designed.
• Prolonged storage of vehicles with fuel injection computers, alarms, GPS
and other electrical devices that require continuous battery power to support
active memories; this power drain must be offset with a maintenance-float
charger, periodic charging or disconnecting the Battery to prevent irreversible
damage. A Battery with an open circuit voltage (OCV) of equal to or less than
8.0V will be deemed as over discharged and void warranty due to misuse
and/or neglect.
WARNING - DO NOT USE ANY TYPE OF OIL, ORGANIC SOLVENT,
ALCOHOL, DETERGENT, STRONG ACIDS, STRONG ALKALIS,
PETROLEUM-BASED SOLVENT OR AMMONIA SOLUTION TO CLEAN THE
BATTERY COVERS AND BATTERY TOPS. THESE MATERIALS MAY CAUSE
PERMANENT DAMAGE TO THE BATTERY COVERS BATTERY TOPS AND
WILL VOID THE WARRANTY.
B. To obtain warranty service:
1. Return the Battery to the original supplying wholesaler or dealer.
2. If the Battery is determined by Manufacturer, in its sole discretion, to be
defective for material or workmanship under terms of this limited warranty,
it will be replaced.
3. Manufacturer’s acceptance of any items shipped to Manufacturer shall
not be deemed an admission that the items so shipped are defective. Any
items shipped back to Manufacturer, shall in Manufacturer’s sole discretion,
become Manufacturer’s property.
THIS LIMITED WARRANTY IS IN LIEU OF, AND MANUFACTURER DISCLAIMS
AND EXCLUDES ALL OTHER WARRANTIES, STATUTORY, EXPRESS
OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
MANUFACTURER’S EXCLUSIVE LIABILITY FOR BREACH OF WARRANTY
SHALL BE TO REPLACE THE BATTERY WITHIN THE EFFECTIVE WARRANTY
PERIOD. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR ANY LOSS
OR DAMAGES OF ANY OTHER KIND, WHETHER DIRECT, INCIDENTAL,
CONSEQUENTIAL, EXEMPLARY, SPECIAL OR OTHERWISE. NOR SHALL
MANUFACTURER BE LIABLE FOR ANY REMOVAL OR INSTALLATION
EXPENSE, OR THE LOSS OF TIME OR PROFITS.
Some countries and/or states do not allow limitation on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to you. This warranty gives
you specific legal rights, which may vary from country to country and/or state
to state. This warranty shall be governed by and interpreted in accordance with
the laws of the Commonwealth of Pennsylvania without regard to Pennsylvania
conflicts of laws rules. The United Nations Convention on Contracts for the
International Sale of Goods signed in Vienna in 1980 shall not apply to this
warranty. This warranty is understood to be the exclusive agreement between
the parties relating to the subject matter hereof. No employee or representative
of Manufacturer is authorised to make any warranty in addition to those made
in this agreement.
Keep your receipt. Receipt is required for longest Warranty Protection.
For your convenience, this space is provided for
attaching your original receipt.
Always properly recycle your lead acid battery by returning to
an authorized recycling centre or automotive dealer.
NEVER PLACE USED BATTERIES IN THE BIN!
EnerSys World
Headquarters
2366 Bernville Road
Reading, PA 19605
Tel: +1-610-208-1991
+1-800-538-3627
EnerSys EMEA
EH Europe GmbH
Löwenstrasse 32
8001 Zürich, Switzerland
Tel: +41 (0) 44 215 74 10
EnerSys Asia
152 Beach Road
Gateway East Building #11-03
Singapore 189721
Tel: +65 6508 1780
www.odysseybattery.com www.enersys.com
© 2013 EnerSys. All rights reserved.
Trademarks and logos are the property of EnerSys and its affiliates, except General Motors®,
which is not the property of EnerSys.
Publication No. 2602-0085, Rev. 11 - EN-ODY-OM-011 - July 2013 - Subject to revisions without prior notice. E.&O.E.
WARRANTY:
EnerSys Energy Products Inc. (“Manufacturer”) warrants its ODYSSEY®
batteries (hereafter referred to as “Battery”) to be free of defects in material and
workmanship for the following Applicable Warranty Periods:
• 2 years for Auxiliary Power (APU) and other non engine start cycling
applications.
• 2 years for power sports applications.
• 3 years for commercial, industrial, marine and automotive applications in non
BCI sizes.
• 4 years for an engine starting application for PC1220, PC1350, PC2250 and
all BCI sizes.
The warranty does not cover a Battery reaching its normal end of life which may
occur prior to the warranty periods stated above. Depending on the application
a Battery can reach its normal end of life before the end of the warranty period.
A Battery can deliver only a fixed number of usable amp-hours over its lifetime
and is considered to have reached its normal end of life if the application
uses up all of these amp-hours, regardless of the time the Battery has been in
service. Therefore Manufacturer reserves the right to deny a warranty claim if it
determines the Battery to be at its normal end of life, even if the claim is lodged
within the applicable warranty period.
The Applicable Warranty Period begins from the date of purchase with original
receipt, or, if no receipt is available, from Manufacturer’s shipping date as stated
on the battery. Batteries determined to meet the conditions of this warranty
will be replaced free of charge if, at the sole discretion of Manufacturer,
adjustment is necessary due to defect in material or workmanship. Batteries for
warranty replacement consideration are to be returned to the original supplying
distributor/dealer. If not feasible, other ODYSSEY distributors/dealers can
be approached but a warranty processing fee may be applied. This warranty
may vary from country to country; contact your authorized ODYSSEY Battery
wholesaler or dealer for the applicable warranty.
Batteries replaced under the warranty provisions will be shipped with a yellow
replacement warranty sticker and carry only the remainder of the original
Applicable Warranty Period.
• To register your ODYSSEY battery, please visit our website at
www.odyssey.com or contact us at 1-888-422-0317
Open as PDF
Similar pages