www.senabluetooth.com
User's Guide
SMH5
CONTENTS
INTRODUCTION
4
tVolume Adjustment
15
PACKAGE CONTENTS
5
tMobile Phone Call Making and Answering
15
INSTALLING THE SMH5 ON YOUR HELMET
6
tEnabling/Disabling Voice Activated Phone Answering, Phone VOX (Factory Default: Enabled)
15
POWERING ON/OFF AND CHARGING
9
tIntercom Conversation
16
tPowering On
9
tIntercom and Mobile Phone Call
17
tPowering Off
9
tIntercom Failure
17
tCharging
9
tIntercom Reconnection
17
tLow Battery Warning
9
tStereo Music
18
10
tFunction Priority
18
tLED Indicator
10
tEnabling/Disabling Voice Prompts (Factory Default: Enabled)
19
tVoice Indicator
10
tEnabling/Disabling PLC, Packet Loss Consealment (Factory Default: Enabled)
19
10
tReset to Factory Default Settings
19
tMobile Phone Pairing
10
tFault Reset
20
tBluetooth Stereo Device Pairing
11
FIRMWARE UPGRADE
20
tBluetooth GPS Navigation Pairing
11
OPERATION QUICK REFERENCE
21
12
BATTERY INFORMATION
21
tA2DP Stereo Music Only
12
MAINTENANCE AND CARE
22
tHFP for Phone Call Only
12
DISPOSAL
22
13
CERTIFICATION AND SAFETY APPROVALS
23
CHECKING THE BATTERY LEVEL
PAIRING THE SMH5 WITH BLUETOOTH DEVICES
PAIRING WITH SELECTIVE PROFILE: A2DP STEREO OR HANDSFREE
PAIRING WITH OTHER SMH5 HEADSETS FOR INTERCOM CONVERSATION
2
PAIRING WITH OTHER SENA HEADSET MODELS FOR INTERCOM CONVERSATION 14
tFCC Compliance Statement
23
USING THE SMH5
tFCC RF Exposure Statement
23
15
SMH5
English
tFCC Caution
23
tCE Declaration of Conformity
23
tIndustry Canada Statement
24
tBluetooth License
24
WAIVER AND GENERAL RELEASE
25
tTwo Year Limited Warranty
26
tLimitation of Liability
27
tReturn for Full Refund
27
WARNING
28
3
SMH5
INTRODUCTION
Thank you for choosing the SENA SMH5, Bluetooth Stereo Headset and
Intercom for scooters and motorcycles. With the SMH5, you can call handsfree
on your Bluetooth mobile phone, listen to stereo music or voice instructions of
GPS navigation by Bluetooth wirelessly, and have intercom conversations in full
duplex with a passenger or other riders.
The SMH5 is compliant with the Bluetooth Specification v3.0 supporting the
following profiles: Headset Profile, Handsfree Profile (HFP), Advanced Audio
Distribution Profile (A2DP), and Audio Video Remote Control Profile (AVRCP).
Please check with the manufacturers of other devices to determine their
compatibility with this headset.
The SMH5 features:
t#MVFUPPUIIBOETGSFFGPS#MVFUPPUINPCJMFQIPOFT
tBluetooth stereo headset for Bluetooth stereo devices such as MP3 players
tBluetooth stereo headset for Bluetooth GPS navigations
tBluetooth intercom up to 400 meters (430 yards)*
tMulti-pair Bluetooth intercom to pair with 3 other headsets
tFirmware upgradeable
Key Specifications:
tBluetooth v3.0
t Supporting profiles: Headset Profile, Hand-Free Profile (HFP), Advanced
Audio Distribution Profile (A2DP), Audio Video Remote Control Profile (AVRCP)
Please read this user’s guide carefully before using the headset. Also check
www.senabluetooth.com/support for the latest version of the user’s guide and
additional information related to SENA Bluetooth products.
-------------------------------*in open terrain
4
SMH5
English
PACKAGE CONTENTS
‡&ODPS8QLW
‡+HDGVHW0DLQ8QLW
‡+HOPHW6SHDNHUV
/('
‡&KDUJLQJ/('
‡$WWDFKDEOH%RRP0LFURSKRQH
-RJ'LDO
3KRQH%XWWRQ
‡86%3RZHU&DEOH
'&3RZHU&KDUJLQJ)LUPZDUH8SJUDGH3RUW
‡*OXHG6XUIDFH0RXQWLQJ3ODWH
5
SMH5
‡0LFURSKRQH6SRQJHV
‡9HOFUR3DGVIRU6SHDNHUV
INSTALLING THE SMH5 ON YOUR HELMET
1. Loosen the two screws on the back plate of the clamp using the enclosed
Allen Wrench. Insert the back plate of the clamp unit between the internal
padding and external shell of the helmet, and tighten the two screws.
‡9HOFUR3DGIRU%RRP0LFURSKRQH
Insert
‡$WWDFKDEOH%RRP0LFURSKRQH+ROGHU
‡6SHDNHU3DGV
‡$OOHQ:UHQFK
6
SMH5
English
2. Attach the headset main unit to the clamp. Insert the main unit in the clamp
until you feel the click that signals a secure attachment.
Note:
Sena recommends the clamp unit over the glued surface mounting plate. Even though the glued
surface mounting plate is provided for convenience, Sena does not assume any responsibility for
use of it. Users may have to use the glued plate at their own risk and responsibility.
3. If you have any problem mounting the clamp unit on the helmet for any
reason, you may use the glued surface mounting plate which can be attached
to the external surface of the helmet.
- Locate a proper surface on the helmet to attach the unit, clean the helmet
surface location with a moistened towel, and allow to dry thoroughly.
- Peel off the cover of the adhesive tape of the plate and attach the unit on the
proper surface of your helmet.
4. Place the helmet speakers along with the velcro pads, centered to your ear,
in the ear pockets of the helmet. If the helmet has deep ear pockets, you can
use the speaker pads to place the speakers closer to your ears.
5. Attach the boom microphone between the internal padding and the external shell. The
boom microphone should be mounted on the inside surface of the external shell so it is
facing properly towards your mouth. Please make sure that the microphone is located
7
SMH5
close to your mouth when you wear the helmet. You can use the enclosed velcro pad
and holder for the boom microphone to ensure secure placement.
7. To remove the headset main unit from the clamp, please make sure to pull out the
speaker cable connector from the main unit first. Then, remove the main unit from the
clamp.
6. Please make sure that the fin side of the microphone is facing outward; away from your
lips. You can easily recognize it by touching the fin with your fingers.
fin
8
SMH5
‡3RZHULQJ2II
Just short press the Jog Dial and the Phone Button simultaneously, you don’t
need to press and hold for a few seconds. The red LED turns on for a while until
it turns off completely and you will hear descending beeps.
‡/RZ%DWWHU\:DUQLQJ
When the battery is low, the blinking blue LED in stand-by mode turns to
red and you will hear mid-tone triple beeps and a voice prompt saying
“Low battery”.
To power on and off the headset, you don’t need to press and hold any
button for several seconds. Just short press the Jog Dial and the Phone Button
simultaneously, and you will get quick on-and-off convenience.
‡&KDUJLQJ
- To charge the SMH5, use the USB Power Cable included in the package
by plugging into computer’s USB port or USB wall charger. USB wall charger
is not included in the package. Any 3rd party USB wall charger can be used
-------------------------------*please contact Sena regarding locally approved agencies Sena accepts.
9
English
‡3RZHULQJ2Q
Press the Jog Dial and the Phone Button at the same time for about 1 second
to power on. The blue LED turns on and you will hear ascending beeps.
with the SMH5 if the charger is approved by either FCC, CE, IC or other locally
approved agencies that Sena accepts.*
- The USB Power Cable is also used for firmware upgrade of the SMH5.
- The Charging LED beside the charging port turns on red while charging, and
turns to blue when the headset is fully charged. It takes about 2.5 hours to be
fully charged.
- You can use the SMH5 while charging. It is especially helpful when you use a
cigarette charger for a long road trip.
- A cigarette charger for the SMH5 is separately available as an optional
accessory.
POWERING ON/OFF AND CHARGING
SMH5
CHECKING THE BATTERY LEVEL
You can check the battery level in two different ways when the headset is
powering on.
‡/(',QGLFDWRU
When the headset is powering on, the red LED flashes rapidly indicating the
battery level.
4 flashes High, 70~100%
3 flashes Medium, 30~70%
2 flashesLow, 0~30%
‡9RLFH3URPSW,QGLFDWRU
When you power on the headset, keep pressing the Jog Dial and Phone
Button simultaneously for about 3 seconds until you hear three high tone
beeps. Then you will hear a voice prompt indicating the battery level. However,
if you release the buttons as soon as the headset turns on, you will not hear the
voice prompt for the battery level.
10
PAIRING THE SMH5 WITH BLUETOOTH DEVICES
Before using the SMH5 Bluetooth headset with any of Bluetooth devices for the
first time, you need to do the pairing operation. It can be paired with Bluetooth
mobile phones, Bluetooth stereo devices such as MP3, or motorcycle specific
Bluetooth GPS, and with other SENA Bluetooth headsets. This pairing operation
is only required once for each Bluetooth device. The headset will remain paired
with the devices and automatically connects to the paired devices again when
they are within range. You will hear a high tone single beep and a voice prompt
when the headset connects to the paired device automatically: “Phone
connected” to a mobile phone, “Media connected” to a Bluetooth stereo
device.
‡0RELOH3KRQH3DLULQJ
1. Turn on the SMH5 and press the Phone Button for 5 seconds until the LED
flashes red and blue alternately and you hear multiple beeps. You will hear a
voice prompt saying “Phone pairing”.
2. Search for Bluetooth devices on your mobile phone. Select the Sena SMH5
in the list of the devices detected on the mobile phone.
SMH5
‡%OXHWRRWK6WHUHR'HYLFH3DLULQJ
1. If the Bluetooth stereo device is integrated with the mobile phone such as
smartphones, you don’t need to pair the SMH5 with it separately. When the
SMH5 is paired with the mobile phone, it is also paired as a stereo music
device.
2. If you have a stand alone Bluetooth stereo device, follow the paring procedure
separately. The procedure is the same as the procedure of “Mobile Phone
Pairing”.
‡%OXHWRRWK*361DYLJDWLRQ3DLULQJ
1. You can listen to Bluetooth voice instructions from a Bluetooth GPS
navigation.
2. The GPS paring procedure is the same as the procedure of “Mobile Phone
Pairing”.
3. Some GPS's use mobile phone profile (HFP, Handsfree Profile) and others
use stereo music profile (A2DP, Advanced Audio Distribution Profile). If you
want to use a mobile phone with a GPS which uses mobile phone profile, you
have to pair the SMH5 with the GPS, and the GPS with the mobile phone. Most
motorcycle specific GPSs use mobile phone profile. Please refer to the manual
of the Bluetooth GPS navigation for details.
Note:
You have to use a motorcycle specific GPS which transmits turn-by-turn voice instruction to the
headset by Bluetooth. Most automotive GPS systems don’t have this feature.
Note:
1. If Bluetooth connection between the headset and a mobile phone is disconnected, tap the
Phone Button to recover the Bluetooth connection immediately.
2. If Bluetooth connection between the headset and a media player is disconnected, press the
Jog Dial for 1 second to recover the Bluetooth connection and play.
11
English
3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.
4. The mobile phone confirms that pairing has completed and the SMH5
is ready to use. You will hear a voice prompt from the SMH5 saying “Your
headset is paired”.
5. If the pairing process is not completed within three minutes, the SMH5 will
return to stand-by mode.
SMH5
PAIRING WITH SELECTIVE PROFILE: A2DP STEREO
OR HANDSFREE
If you have a MP3 stereo music phone such as a smartphone, sometimes you
may need to selectively use the SMH5 for A2DP stereo music only or for mobile
phone handsfree only. This instruction is for advanced users who want to pair
the SMH5 to their smartphones only with one selective profile: A2DP for stereo
music or HFP for phone call.
If you have previously paired a mobile phone to the SMH5, you must clear the
previous paring list on both devices; the mobile phone and SMH5. To clear
the pairing list on SMH5, please do a factory reset described on the page
19.To clear the pairing list on the mobile phone, please refer to the mobile
phone manual. For most smartphones, delete the Sena SMH5 from the list of
Bluetooth devices in setting menu.
‡$'36WHUHR0XVLF2QO\
1. Turn on the headset and press the Phone Button for 5 seconds until the LED
flashes red and blue alternately and you hear multiple beeps.
12
2. Within 2 seconds, tap the Jog Dial again, then the LED turns to red flashing
and the beeps turn to double mid-tone beeps. You will hear a voice prompt
saying “Media selective pairing”.
3. Search for Bluetooth devices on your smartphone. Select the Sena SMH5
in the list of devices detected on your phone.
4. Enter 0000 for the PIN. Some smartphones may not ask for PIN.
‡+)3IRU3KRQH&DOO2QO\
1. Turn on the headset and press the Phone Button for 5 seconds until the LED
flashes red and blue alternately and you hear multiple beeps.
2. Within 2 seconds, tap the Phone Button again, then the LED turns to blue
flashing and the beeps turn to multiple mid-tone beeps. You will hear a voice
prompt saying “Phone selective pairing”.
3. Search for Bluetooth devices on your smartphone. Select the Sena SMH5
in the list of devices detected on your phone.
4. Enter 0000 for the PIN. Some smart phones may not ask for PIN.
SMH5
A
English
PAIRING WITH OTHER SMH5 HEADSETS FOR
INTERCOM CONVERSATION
'
B
The SMH5 can be paired with up to three other headsets for Bluetooth
Intercom conversation.
1. Turn on the two SMH5 headsets (A and B) that you would like to pair with
each other.
2. Press and hold the Jog Dial of the headset A and B for 5 seconds until red
LEDs of the both units start to flash rapidly. You will hear a voice prompt saying
“Intercom pairing”.
3. Simply tap the Jog Dial of any one of the two headsets A or B (It doesn’t
matter that you choose A or B) and wait until the LEDs of both headsets turn
to blue and intercom connection is automatically established. The two SMH5
headsets A and B are paired with each other for intercom conversation. If the
pairing process is not completed within one minute, the SMH5 will return to
stand-by mode.
&
Pairing A & B
4. You can make other pairings between the headset A and C, and between
the headset A and D by following the same procedure as above.
A
B
A
'
&
Pairing A & C
B
'
&
Pairing A & D
13
SMH5
5. The intercom pairing queue is ‘Last-Come, First-Served’. If a
headset has multiple paired headsets for intercom conversations, the last
paired headset is set as first intercom friend. The previous Intercom friend
becomes second intercom friend, and third intercom friend.
Note:
For example, after the pairing procedures listed above, headset D is the first intercom friend of
headset A. Headset C is the second intercom friend of headset A, and headset B is the third
intercom friend of headset A.
14
PAIRING WITH OTHER SENA HEADSET MODELS FOR
INTERCOM CONVERSATION
The SMH5 can be paired with all other SENA headset models such as the
SMH10 and the SPH10 for intercom conversation. Please follow the same
procedure as above to pair with these headset models.
SMH5
‡9ROXPH$GMXVWPHQW
You can easily adjust the volume by rotating the Jog Dial. You will hear a beep
when the volume reaches maximum or minimum level. The volume is set and
maintained independently at different levels for each audio source even when
you turn off and on the headset. For example, once you set the volume for
mobile phone handsfree, it will not change even if you adjust the volume when
you hear Bluetooth MP3 music. So you can always maintain the preferred
optimum volume level for each audio source.
‡0RELOH3KRQH&DOO0DNLQJDQG$QVZHULQJ
1. When you have an incoming call, simply tap the Jog Dial or the Phone Button
to answer the call.
2. You can also answer the incoming call by loudly speaking any word of your
choice if Voice Activated Phone Answering, Phone VOX is enabled. (Refer to
the next section for details.)
3. To end a call, tap the Jog Dial or the Phone Button, or wait for the called
person to end the call.
4. To reject a call, press the Jog Dial for 2 seconds until you hear a beep while
the phone is ringing.
5. To transfer a call between the mobile phone and the headset during the phone
conversation, press the Phone Button for 2 seconds until you hear a beep.
6. There are several ways to make a phone call:
- Enter numbers on your mobile phone keypad and make a call. Then the call
is automatically transferred to the headset.
- For some older mobile phones which do not automatically transfer calls to the
headset, press the Phone Button after entering phone numbers on the mobile
phone keypad.
- Tap the Phone Button in stand-by mode to activate the voice dialing of your
mobile phone. For this, the voice dialing feature must be available on the mobile
phone. Refer to your mobile phone manual for further instruction.
- To redial the last number, double tap the Phone Button in stand-by mode. You
will hear a voice prompt saying “Last number redial”.
‡(QDEOLQJ'LVDEOLQJ9RLFH$FWLYDWHG3KRQH$QVZHULQJ
3KRQH92;)DFWRU\'HIDXOW(QDEOHG
If this feature is enabled, you can answer incoming calls by simply saying a
word loudly enough. For example, when you hear a series of beeps for an
15
English
USING THE SMH5
SMH5
incoming call, you can answer the phone by saying “Hello” or any other word
loudly. This is enabled from the factory but you can disable this. If this mode is
disabled, the only way to answer an incoming call is to tap the Phone Button.
1. Press and hold the Phone Button for 8 seconds until the red LED is rapidly
flashing. When you do this, after first 5 seconds you press the button, you will
see the headset enter into the Mobile Phone Pairing sequence, but you have
to keep pressing the button for another 3 seconds until the red LED flashes
rapidly. You will hear a voice prompt saying “VOX phone”.
2. To disable, tap the Jog Dial within 10 seconds, then you will hear a single
beep and the red LED flashes for 2 seconds. To enable VOX, tap the Phone
Button within 10 seconds, then you will hear a double beep and the blue
LED flashes for 2 seconds. If any button is not pressed within 10 seconds, it
remains unchanged and goes back to stand-by.
‡,QWHUFRP&RQYHUVDWLRQ
1. You can start an intercom conversation with any of intercom friends by
tapping the Jog Dial: single tapping to intercom with the first intercom friend,
double tapping with the second intercom friend, and triple tapping with the
third intercom friend.
16
1st Intercom Friend
2nd Intercom Friend
3rd Intercom Friend
2. To terminate an intercom conversation, single tap the Jog Dial. Any intercom
connection with any intercom friend will be terminated by a single tapping. A
double or triple tapping will do nothing in this case.
SMH5
Terminate
‡,QWHUFRPDQG0RELOH3KRQH&DOO
1. When you have an incoming mobile phone call during an intercom
conversation, you will hear a ring tone. You can choose whether to 1) answer
the mobile phone call and stop the intercom conversation, or 2) reject the
phone call and stay on the intercom conversation.
- To answer the phone call and stop the intercom conversation, tap the Jog
Dial or the Phone Button. When you hang up the phone call, the intercom will
automatically be recovered.
- To reject the phone call and stay on the intercom conversation, press the Jog
Dial for 2 seconds until you hear a beep.
Unlike other motorcycle Bluetooth headsets, this prevents a user from being
dropped out of an intercom conversation by an incoming mobile call.
‡,QWHUFRP)DLOXUH
When you try to start an intercom conversation with an intercom friend who is
already having an intercom conversation with other intercom friend or a mobile
phone call , you will hear a low tone double beep signifying a busy signal. You
will also hear a voice prompt saying “Intercom failed, try again later”. In this
case, you have to try again later. On the other hand, the intercom friend will
hear 4 high tone beeps alerting them that there is an incoming intercom call.
‡,QWHUFRP5HFRQQHFWLRQ
If your intercom friend goes out of range while having an intercom conversation,
you may hear static noise and eventually the intercom will be disconnected.
In this case, the SMH5 automatically tries to reconnect the intercom every
8 seconds. You will hear high tone double beeps until the intercom is
17
English
2. When you have an incoming intercom call during a mobile phone call, you
will hear 4 high tone beeps, alerting you that there is an incoming intercom call.
You will also hear a voice prompt saying “Intercom requested”. In this case,
the intercom call does not override the mobile phone call because intercom
has lower priority than mobile call. You have to hang up the mobile phone call
to make or receive an intercom call.
SMH5
reestablished. If you don’t want to make a reconnection, tap the Jog Dial to
stop the attempt.
‡6WHUHR0XVLF
You can listen to stereo music by Bluetooth wireless stereo. The Bluetooth
audio device must be paired with the SMH5 by following the Bluetooth Stereo
Device Pairing procedures described in the previous chapter. The SMH5
supports the Audio/Video Remote Control Profile(AVRCP), so if your Bluetooth
audio device also supports the AVRCP, you can use the SMH5 to remotely
control music playback. So, You not only can adjust the volume but also use
the functions such as play, pause, next track and previous track.
- To play or pause music, press and hold the Jog Dial for 1 second until you
hear a double beep.
- To track forward or track back, rotate while pressing the Jog Dial clockwise
or counter clockwise.
- To adjust the volume, rotate the Jog Dial.
‡)XQFWLRQ3ULRULW\
The SMH5 operates in the following order of priority:
(Highest)
Mobile Phone,
Intercom, and
(Lowest)
Bluetooth Stereo Music
18
SMH5
‡(QDEOLQJ'LVDEOLQJ9RLFH3URPSWV)DFWRU\'HIDXOW(QDEOHG
The voice prompt feature is enabled from the factory, and is enabled or
disabled by the following procedures.
1. Press and hold the Jog Dial for 8 seconds until the blue LED is rapidly
flashing and you hear a mid-tone double beep. You will also hear a voice
prompt saying “Voice prompt”.
2. To disable, tap the Jog Dial within 10 seconds, then you will hear a single
beep and the red LED flashes for 2 seconds. To enable the voice prompts, tap
the Phone Button within 10 seconds, then you will hear a double beep and the
blue LED flashes for 2 seconds. If any button is not pressed within 10 seconds,
it remains unchanged and goes back to stand-by.
‡(QDEOLQJ'LVDEOLQJ3/&3DFNHW/RVV&RQVHDOPHQW)DFWRU\
'HIDXOW(QDEOHG
The PLC (Packet Loss Concealment ) algorithm is enabled from the factory,
and is enabled or disabled by the following procedures. It is recommended
to enable this setting. The PLC algorithm improves the audio quality of the
intercom and mobile phone handsfree in the presence of data packet errors
within the Bluetooth link.
1. Press and hold the Jog Dial for 12 seconds until the LED shows sold blue
and you hear a high tone double beep. You will also hear a voice prompt saying
“PLC setting”.
2. To disable, tap the Jog Dial within 10 seconds, then you will hear a single
beep and the red LED flashes for 2 seconds. To enable the PLC algorithm, tap
the Phone Button within 10 seconds, then you will hear a double beep and the
blue LED flashes for 2 seconds. If any button is not pressed within 10 seconds,
it remains unchanged and goes back to stand-by.
‡5HVHWWR)DFWRU\'HIDXOW6HWWLQJV
1. To restore the SMH5 to factory default settings, press and hold the Phone
Button for 12 seconds until the LED shows solid red and you hear high tone
double beeps. You will also hear a voice prompt saying “Factory reset”.
2. Within 5 seconds, press the Jog Dial to confirm reset. The headset will be
restored to factory setting and switched off automatically. You will hear a voice
19
English
A lower priority function is always interrupted by a higher priority function.
For example, stereo music is interrupted by intercom call, and intercom
conversation is interrupted by incoming mobile phone call.
SMH5
prompt saying “Headset reset, good-bye”.
3. If you don’t press the Jog Dial within 5 seconds, the reset attempt is
canceled and the headset returns to stand-by mode. You will hear a voice
prompt saying, “Canceled”.
‡)DXOW5HVHW
When the SMH5 is not working properly or is in faulty status for any reason, you
may reset by pushing the pin-hole reset button at the back of the headset main
unit. Insert a paper clip into the reset pin-hole and press the reset button for 1
second with light pressure. The SMH5 will be switched off after which time, you
have to turn the system back on and try again. However, this will not restore the
headset to factory default settings.
20
FIRMWARE UPGRADE
The SMH5 supports firmware upgrade function. Please visit SENA Bluetooth
web site at www.senabluetooth.com to check the latest firmware
downloads.
SMH5
BATTERY INFORMATION
Button
Description
Duration
LED
Phone Button
+ Jog Dial
Power-on
1 sec
Solid blue
Ascending beeps
Power-off
Tapping
Solid red
Descending beeps
Answer & end mobile phone call
Tapping
—
—
Mobile phone voice command
Tapping
—
—
Call transfer while on the phone
2 sec
—
High tone beep
Enter into Bluetooth device
pairing mode
5 sec
Blue & red
alternativel flashing
Mid-tone single beep &
High tone triple beeps
8 sec
Red flashing
Mid-tone double beeps
Phone Button
Beep
Phone VOX setting
English
OPERATION QUICK REFERENCE
The Product has an internal, non-removable, rechargeable battery. Do not
|attempt to remove the battery from the device as you may damage the
device. The battery can be charged and discharged hundreds of times, but
it will eventually wear out. Recharge the battery only with SENA approved
chargers designated for this device. Use of an unapproved charger may present
a risk of fire, explosion, leakage, or other hazard.
Phone Button to enable, Jog Dial to disable
12 sec
Solid red
Factory reset
High tone double
beeps
Jog Dial within 5 sec to confirm reset
Jog Dial
Volume adjustment
Rotating
—
—
Answer & end mobile phone call
Tapping
—
—
Start & end intercom conversation
Tapping
—
—
Play & pause music
1 sec
—
Mid-tone double beeps
Track-forward & track-back
Rotating w/pressing
—
—
Reject incoming mobile phone call
while the phone is ringing
2 sec
—
—
5 sec
Red flashing
Mid-tone single beep &
Double-tone beeps
Intercom pairing
Jog Dial of any one of the two headsets
8 sec
Blue flashing
Mid-tone double beeps
Voice prompts setting
Phone Button to enable, Jog Dial to disable
12 sec
Solid blue
PLC setting
High tone double
beeps
Always try to keep the battery between 15Ⳅ and 25Ⳅ (59ⳅ and 77ⳅ).
Extreme temperatures reduce the capacity and lifetime of the battery.
A device with a hot or cold battery may not work temporarily. Battery
performance is particularly limited in temperatures well below freezing.
Do not dispose of batteries in a fire as they may explode. Batteries may
also explode if damaged. Never use any charger that is damaged. Operating
times are estimates only and depend on the devices used together, features
used, battery age and condition, temperatures to which battery is exposed,
and many other factors.
Phone Button to enable, Jog Dial to disable
21
SMH5
MAINTENANCE AND CARE
The Product should be treated with care and the following suggestions will
help you protect your warranty coverage.
1. Do not use or store the device in dusty, dirty areas. Its moving parts and
electronic components can be damaged.
2. Do not store the device in hot areas. High temperatures can shorten the life of
electronic devices, damage batteries, and wrap or melt certain plastics.
3. Do not store the device in cold areas. When the device returns to its normal
temperature, moisture can form inside the device and damage electronic circuit
boards.
4. Do not attempt to open the product.
5. Do not drop or knock the device. Rough handling can break internal circuit
boards and fine mechanics.
6. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the
device.
7. Do not paint the device. Paint can clog the moving parts and prevent proper
operation.
These suggestions apply equally to the headset main unit, clamp unit, or power
charger.
22
DISPOSAL
The crossed-out wheel bin symbol on the product,
|literature, or packaging reminds you that all electrical and
electronic products, batteries, and accumulators must be
taken to separate collection at the end of their working life.
This requirement applies to the European Union and other
locations where separate collection systems are available. To prevent
possible harm to the environment or human health from uncontrolled
waste disposal, please do not dispose of these products as unsorted
municipal waste, but hand it in at an official collection point for recycling.
SMH5
‡)&&&RPSOLDQFH6WDWHPHQW
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
‡)&&5)([SRVXUH6WDWHPHQW
The antenna(s) used for this device must be installed to provide a separation
distance of at least 20 cm from all persons and must not be colocated or
operating in conjunction with any other antenna or transmitter.
‡)&&&DXWLRQ
Any changes or modifications to the equipment not expressly approved by
the party responsible for compliance could void user’s authority to operate the
equipment.
‡&('HFODUDWLRQRI&RQIRUPLW\
This product is CE marked according to the provisions of the R&TTE Directive
(99/5/EC). Hereby, SENA declares that this product is in compliance with the
23
English
CERTIFICATION AND SAFETY APPROVALS
SMH5
essential requirements and other relevant provisions of Directive 1999/5/EC. For
further information please consult www.senabluetooth.com Please note that
this product uses radio frequency bands not harmonized within EU. Within the EU
this product is intended to be used in Austria, Belgium, Denmark, Finland, France,
Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain,
Sweden, United Kingdom and within EFTA in Iceland, Norway and Switzerland.
‡,QGXVWU\&DQDGD6WDWHPHQW
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
‡%OXHWRRWK/LFHQVH
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and
any use of such marks by SENA is under license. Other trademarks and trade
names are those of their respective owners
24
The SMH5 is compliant with and adopts the Bluetooth® Specification 3.0
and has successfully passed all interoperability tests that are specified in the
Bluetooth® specification. However, interoperability between the device and other
Bluetooth®-enabled products is not guaranteed.
SMH5
the Device while actively involved in traffic.
By using the product you waive all substantial legal rights including the right to
sue. Please read the following carefully before using the device. If you do not
accept all terms of this agreement, you should immediately return the product for
a full refund. By using the headset you agree to be bound to this agreement and
forfeit the right to sue. Using a communication device while riding a motorcycle,
scooter, moped, ATV, quad-bike or any other vehicle or equipment, whether on land,
water or air (jointly referred to as “Vehicle”) requires your complete and undivided
attention. SENA Technologies, Inc., including its Officers, Directors, Affiliates,
Parent Company, Representatives, Agents, Contractors, Sponsors, Employees,
Suppliers and Resellers (jointly referred to as the “Company” or “SENA”) strongly
advises you to take all necessary precautions and remain alert to the traffic,
weather and road conditions if you choose to use the product headset, including
all derivative models irrespective of its commercial name or branding (the “Device”),
and stop your Vehicle on the roadside prior to initiating or receiving calls. Any
publications, advertisements, announcements or similar notes that refer to
using the Device while riding a Vehicle are solely intended to address its technical
capabilities and should not be misconstrued as if encouraging users to operate
By way of purchasing this Device and not returning it for a full refund (see
below), you are irrevocably releasing, indemnifying from any liability, loss, claim
and expense (including attorney’s fees) and holding SENA harmless for any
bodily injuries, harm or death as well as losses or damages in goods, to any
Vehicles including your own, or to any property or asset that belong to you or
to third parties, any of which may result from using the Device under any
circumstances or conditions and irrespective of jurisdiction. SENA will not be
responsible for any physical damages, irrespective of reasons, conditions or
circumstances, including malfunctioning of the Device, and all risks associated
with operating it rest solely and entirely with the user of this Device, irrespective of
whether the Device is used by the original purchaser or any third party.
SENA hereby notifies you that using this Device may also be in contravention to
local, federal, state or national laws or regulations, and that any use of the Device
is entirely at your sole risk and responsibility.
1. You, your heirs, legal representatives, successors or assigns, hereby
voluntarily and forever release, discharge, indemnify and hold harmless SENA
from any and all litigation, claims, debts, demands, actions and liability which
25
English
WAIVER AND GENERAL RELEASE
SMH5
may arise, directly or indirectly, from using the Device for any distress, pain,
suffering, discomfort, loss, injury, death, damages to or in respect to any person
or property however caused, WHETHER ARISING FROM THE NEGLIGENCE OR
OTHERWISE, and which may hereafter accrue to you on some future date as a
result of said use, to the fullest extent permitted by law.
2. You fully understand and assume the risks in using the Device, including risk of
negligent acts or omissions by others.
3. You confirm that you are physically capable to use the Device and that you have
no medical conditions or needs that may infringe upon your abilities to do so in
a safe manner. You confirm that you are at least eighteen (18) years of age and
that you have been advised of the risks associated with the use of the Device.
You further confirm that you will not consume any alcohol that may affect your
alertness or any mind-altering substance, and will not carry, use or consume these
substances before or during the use of the Device.
4. You fully acknowledge our warnings and understand that: (a) risks and
dangers exist in using the Device while in traffic, including but not limited to injury
or illness, strains, fractures, partial and/or total paralysis, death or other ailments
that could cause serious disability; (b) these risks and dangers may be caused
by the negligence of the manufacturers or its agents or any third party involved in
designing or manufacturing the Device; (c) these risks and dangers may arise
26
from foreseeable or unforeseeable causes. You hereby assume all risks and
dangers and all responsibility for any losses and/or damages, whether caused
in whole or in part by the negligence or other conduct of others, including the
Company.
5. You confirm that you have read this release of liability and fully understand its
terms and that you have given up substantial rights by not returning the Device for
a full refund (see refund option below).
‡7ZR<HDU/LPLWHG:DUUDQW\
Sena Technologies, Inc. (“SENA”) warrants that this product (“Product”) shall
conform to and perform in accordance with published technical specifications
and the accompanying written materials, and shall be free of defects in materials
and workmanship, for a period of two (2) year from the date of purchase by the
first consumer purchaser of the Product. The limited warranty extends only to the
original consumer purchaser of the Product and is not assignable or transferable
to any subsequent purchaser/end-user.
This warranty is limited to the repair and/or replacement, at SENA’s discretion,
of defective or non-conforming Product, and SENA shall not be responsible
for the failure of the Product to perform specified functions, or any other
nonconformance caused by or attributable to: (a) any misapplication or misuse of
SMH5
‡/LPLWDWLRQRI/LDELOLW\
EXCEPT AS EXPRESSLY PROVIDED HEREIN, SENA MAKES NO WARRANTY
OF ANY KIND, EXPRESSED OR IMPLIED, WITH RESPECT TO ANY
EQUIPMENT, PARTSORSERVICESPROVIDEDPURSUANTTOTHISAGREEMENT,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. NEITHER
SENA NOR ITS DEALER SHALL BE LIABLE FOR ANY OTHER DAMAGES,
INCLUDING BUT NOT LIMITED TO DIRECT, INDIRECT, INCIDENTAL, SPECIAL
OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION IN CONTRACT
OR TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY), SUCH AS, BUT
NOT LIMITED TO, LOSS OF ANTICIPATED PROFITS OR BENEFITS RESULTING
FROM, OR ARISING OUT OF, OR IN CONNECTION WITH THE USE OF
|FURNISHING OF EQUIPMENT, PARTS OR SERVICES HEREUNDER OR THE
PERFORMANCE, USE OR INABILITY TO USE THE SAME, EVEN IF SENA OR ITS
DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN
NO EVENT WILL SENA OR ITS DEALERS TOTAL LIABILITY EXCEED THE PRICE
PAID FOR THE PRODUCT.
‡5HWXUQIRU)XOO5HIXQG
IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE
CONDITIONS, YOU MAY RETURN THIS DEVICE TO SENA FOR A FULL
REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 14 BUSINESS
DAYS FOLLOWING THE PURCHASE OF THE DEVICE AND SUBJECT TO THE
WRAPPING BEING INTACT. WHEN DOING SO, PLEASE REFER TO THIS
SECTION. BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE
PERIOD PROVIDED, YOU ARE EXPLICITLY IN AGREEMENT WITH THE ABOVE
AND RENOUNCE ALL RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST
SENA AS DEFINED ABOVE.
27
English
the Product; (b) failure of Customer to adhere to any of SENA’s specifications or
instructions; (c) neglect of, abuse of, or accident to, the Product; or (d) any associated or
complementary equipment or software not furnished by SENA.
Limited warranty service may be obtained by delivering the Product to SENA or
to the international distributor it was purchased through and providing proof of
purchase or receipt date. Customer agrees to insure the Product or assume the
risk of loss or damage in transit, to prepay shipping charges to SENA, and to use
the original shipping container or equivalent.
SMH5
WARNING
SENA informs that using this device in public traffic may not be authorized by
the law. Please check your local law and use this device only out of public traffic
such as private properties or closed circuits. If the simultaneous use of both
ear speakers while riding a motorcycle is prohibited by your local law, please
use only a single ear speaker while riding. SENA denies any liability should you
choose not to respect this warning.
Using the headset with loud volume may be harmful to your eardrums and
cause hearing loss. Please maintain proper volume level to protect your ears.
28
1.0.1
www.senabluetooth.com
User's Guide for Firmware V1.1
Open as PDF
Similar pages