40MHz Analog Oscilloscope HM400

99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com
40 MHz Analog Oscilloscope
HM400
HM400
NEW
No signal distortion
resulting from overshoot
Reference-Class in sensitivity and input voltage range
2 Channels with deflection coefficients 1 mV/div.…20 V/div.,
variable up to 50 V/div.
Line triggered composite
video signal
Time Base 0.2 s/div.…100 ns/div.,
with X magnification to 10 ns/div.
Low noise measuring amplifiers with high pulse fidelity
and minimum overshoot
Peak to peak trigger for stable triggering 0…50 MHz
at 0.5 div. signal level (up to 80 MHz at 1 div.)
Caracteristic of a Z-Diode
with component test mode
Autoset, Save/Recall Memories for 6 instrument settings
Yt- and XY-Mode with Z-Input for intensity modulation
Component characterisation with component tester
(two terminal network measurement) for use within service etc.
Low power consumption, no fan
40 MHz Analog Oscilloscope HM400
All data valid at 23 °C after 30 minute warm-up
Vertical Deflection
Operating Modes:
Invert:
XY Mode:
Bandwidth (-3 dB):
DC, 5mV/div.…20V/div.:
AC, 5mV/div.…20V/div.:
DC, 1mV/div.…2mV/div.:
AC, 1mV/div.…2mV/div.:
Rise Time (calculated):
Deflection Coefficient:
Variable (uncalibrated):
Input Impedance:
Input Coupling:
Max. Input Voltage:
Triggering
Automatic (Peak to Peak):
Normal with Level Control:
Slope:
Sources:
Coupling:
Channel 1 or 2 only
Channels 1 and 2 (alternate or chopped)
Sum or Difference of CH 1 and CH 2
CH 2
CH 1 (X) and CH 2 (Y)
0…40MHz
2Hz…40MHz
0…10MHz
2Hz…10MHz
‹ 35 ns (1 mV/div.…2 mV/div.)
‹ 8,75 ns (5 mV/div.…20 V/div.)
1-2-5 Sequence
± 5% (1 mV/div.…2 mV/div.)
± 3% (5 mV/div.…20 V/div.)
› 2.5:1 to › 50 V/div.
1 MΩ II 15 pF
DC, AC, GND (ground)
400 V (DC + peak AC)
Miscellaneous
CRT:
Acceleration Voltage:
Trace Rotation:
Z-Input (Intens. modulation):
Probe ADJ Output:
Power Supply (Mains):
Power Consumption:
Safety class:
Operating temperature:
Storage temperature:
Max. rel. humidity:
Dimensions (W x H x D):
Weight:
D14-363GY, 8 x 10 div. with internal graticule
approx. 2 kV
adjustable on front panel
max. + 5 V (TTL), 10 kHz
1 kHz / 1 MHz Square Wave Signal ca. 0.2 Vpp
(tr ‹ 5 ns) for probe adjustment
105/253 V, 50/60 Hz ± 10 %, CAT II
approx. 30 Watt at 230 V/50 Hz
Safety class I (EN61010-1)
+5°C...+40°C
-20°C...+70°C
5%...80% (non condensing)
285 x 125 x 380 mm
approx. 4.8 kg
Accessories supplied: Line Cord, Operators Manual, 2 Probes 1:1/10:1 (HZ154)
with LF/HF adjustment
5 Hz…50 MHz (≥ 0.5 div.),
50 MHz…80 MHz (≥ 1 div.)
0…50 MHz (≥ 0.5 div.),
50 MHz…80 MHz (≥ 1 div.)
Rising or falling
Channel 1 or 2, Line and External
AC (5 Hz…80 MHz), DC (0…80 MHz),
LF (0…1.5 kHz)
LED
Trigger Indicator:
External Trigger:
Input Impedance:
1MΩ II 15pF
External Trigger Signal: 0,3 Vpp ≤5 V,
DC (0…50 MHz), AC (20 Hz…50 MHz)
Max. input voltage:
100V (DC + Peak AC)
Active TV sync. separator:
Field and Line, +/Horizontal Deflection
Time Base:
Accuracy:
Variable (uncalibrated):
X Magnification x 10:
Accuracy:
Hold-Off Time:
XY
Bandwidth X amplifier:
XY Phase shift ‹ 3°:
0.2 s/div.…100 ns/div. (1-2-5 Sequence)
± 3%
› 2.5 :1 to › 1.25 s/div.
up to 10 ns/div.
± 5%
variable to approx. 10 : 1
0…2.5 MHz (-3 dB)
‹ 120 kHz
Operation / Readout / Control
Manual:
via controls and buttons
Autoset:
automatic signal related parameter settings
Save and Recall:
6 instrument parameter settings
Component Tester
Test Voltage:
Test Current:
Test Frequency:
Test Connection:
approx. 7 Vrms (open circuit)
max. 7 mArms (short-circuit)
approx. 50 Hz
2 banana jacks 4 mm Ø
One test circuit lead is grounded via protective earth (PE)
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
FAX 781.665.0780 - TestEquipmentDepot.com
Open as PDF
Similar pages