Portable Multi Work Stand

Model No. UT1004
Owner’s Manual
Portable Multi Work Stand
QUESTION...
1•847•780•6120
Visit us on the web at www.southerntechllc.com
You will need this manual for safety instructions, operating procedures, and warranty.
Put it and the original sales invoice in a safe, dry place for future reference.
15-0901
TABLE OF CONTENTS
SECTION
SAFETY RULES
PAGE
1
PRODUCT
SPECIFICATIONS
Tabletop (LxW)..................................23-1/2" x 18"
(59.7 cm x 45.7)
Height (lowest position).....................23-1/2" (59.7 cm)
ASSEMBLY
2
Unpacking
Tools Needed
Unfold the Work Legs
Assemble Handle
Assemble Extension Bar/Roller Bar Locking
Knobs
Mounting the Power tool
OPERATIONS
4
Height (6 preset positions)................23-1/2" (59.7 cm),
28-1/4" (71.7 cm),
29-1/4" (74.3 cm),
30-1/4" (76.8 cm),
31-1/4" (79.4 cm),
32-1/4" (81.9 cm)
Stand
(folded w/o extensions (LxWxH)....... 2
5-3/8" x 20-1/2" x
6-1/2" (64.4 cm x
52 cm x 16.5 cm)
Distance between rollers...................35" (89 cm) (min)
66-1/8" (168 cm)(max)
Roller Bar/Extension Bar Adjustment
Leg Adjustment
Transportation/Storage
MAINTENANCE
Height (tallest position).....................32-1/4" (81.9 cm)
Rollers adjustment from table top.....3" (7.6 cm) (min)
8-1/4" (20.9 cm) (max)
4
Metal rollers (DxL).............................1-7/16" x 9-1/2"
(3.7 cm x (24 cm)
Maximum Load.................................330 lbs. (150 kg)
General Maintenance
PARTS ILLUSTRATION
& LIST
5
WARRANTY
6
Weight without extensions................36.3 lbs. (16.5 kg)
Weight with extensions.....................39.16 lbs. (17.8 kg)
WARNING
For your own safety, read all of the rules and precautions
before operating tool.
WARNING
Always follow proper operating procedures as defined in
this manual even if you are familiar with use of this ultrawork stand or any tool used with this stand. Remember
that being careless for even a fraction of a second can
result in severe personal injury.
You must be familiar with the use of any tool or accessory
used with this ultra-work stand. The supplier cannot
be held responsible for any accident, injury or damage
incurred while using this stand with any tool.
WARNING
Some dust created by operation of power tool contains
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm. To
reduce your exposure to these chemicals, work in a well
ventilated area and work with approved safety equipment.
Always wear OSHA/NIOSH approved, properly fitting face
mask or respirator when using such tools.
CAUTION
Do not modify or use this stand for any application other
than that for which it was designed.
ELECTRICAL SAFETY
• Avoid body contact with grounded surfaces, such as
pipes, radiators, ranges, and refrigerators. There is an
increased risk of electric shock if your body is grounded.
• Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
• Do not abuse the cord. Never use the cord for carrying,
pulling, or unplugging the power tool. Keep the cord
away from heat, oil, sharp edges, or moving parts.
Damaged or entangled cords increase the risk of
electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter (GFCl}
protected supply. Use of a GFCI reduces the risk of
electric shock.
SAFETY FOR WORK STAND
• Do not attempt to assemble or operate your ultra-work
stand until you have read the safety instructions in this
section.
1
• Only use your ultra-work stand on a hard, dry and flat
surface.
• Keep your work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not overreach. Keep proper footing and balance at
all times.
• Do not load the ultra-work stand with more than 330 lbs.
(150 kg).
• Store properly. Do not store the ultra-work stand
outdoors or in a damp location.
• Do not stand or climb on ultra-work stand. It could tip
over, causing serious injury.
• Do not permit children to use the ultra-work stand
unsupervised. It is not a toy.
• Be sure work support extensions are locked in place
before using your power tool and ultra-work stand.
• Take care when moving the stand, especially when a
power tool is mounted.
• Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair can be caught
in moving parts. Always wear non-slip footwear. Tie
back long hair. Roll long sleeves above the elbow.
• Always firmly attach the power tool used with this stand.
Do not attempt to use the power tool on the ultra-work
stand until the power tool is fastened firmly.
• Be aware of tipping. When a large piece is cut from one
end of a job, the remaining piece may be heavy enough
to tip the ultra-work stand. Always ensure the workpiece
is well supported.
• Always keep all guards in place. Be sure all power tool
guards are in good working order and are in proper
adjustment and alignment.
• Always keep your hands away from the cutting area.
CAUTION
Think safety! Safety is a combination of operator common
sense and alertness at all times when tool is being used.
WARNING
Do not attempt to operate tool until it is completely
assembled according to the instructions.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
SAFETY RULES
SAFETY RULES
1
ASSEMBLY
ASSEMBLY
2
2
UNPACKING
TOOLS NEEDED
Refer to Figure 1
Check for shipping damage. Check immediately whether
all parts and accessories are included.
The following tools (not included) are needed to assemble
the ultra-work stand:
ITEM
A
B
C
D
E
F
G
H
DESCRIPTION
Ultra-work stand
Extension bars
Roller bars
Locking knobs
Handle
Screws and lock nuts (handle)
Power tool mounting hardware
(mounting bolt, washer, lock washers and
nut)
Pan head screws
QTY
1
2
2
4
1
2
4
2
Figure 1
Phillips head screwdriver
10 mm open end wrench
UNFOLD THE WORK LEGS
Refer to Figure 2
• Place the ultra-work stand on a flat surface with the
folded legs facing up.
• Depress the leg release spring pins and rotate the leg
until it clicks and locks into the open position. Repeat for
each leg.
Figure 2
Leg
A
H
F
E
D
C
Leg Release
Spring Pins
B
G
WARNING
Do not use the ultra-work stand until it is completely
assembled and you have read and understood this entire
operating manual and the operating manual of the tool
being used with this ultra-work stand.
• Place the ultra-work stand in the upright position on a
flat surface.
ASSEMBLE HANDLE
Refer to Figure 3
• Secure handle to frame with hardware supplied.
Figure 3
WARNING
Do not use the ultra-work stand for scaffolding or as a
ladder. Make sure to securely tighten all fasteners before
using. Maximum capacity is 330 lbs. (150 kg). Power tools
on the ultra-work stand should not exceed a combined
overall height of 60" (152.4 cm) from the floor.
Lock Nut
Handle
Screw
ASSEMBLE EXTENSION BAR/ROLLER BAR
LOCKING KNOBS
Refer to Figure 4, 5
The two extension bars can be assembled in the
extension bar brackets found at the right and left of the
stand.
Extension
Bar Bracket
Figure 4
Extension
Bar
Extension
Bar Bracket
3
MOUNTING THE POWER TOOL
WARNING
Risk of accidental starting and serious personal injury.
Unplug the power tool before attaching it to the ultra-work
stand.
WARNING
3
Risk of serious personal injury. Always make sure the
power tool is fully supported and securely attached to
a level work surface. Make sure the ultra-work stand is
located on a flat surface.
IMPORTANT: Use the mounting hardware supplied to
mount the power tool to the ultra-work stand. Always
insert the bolt from the bottom of the ultra-work stand.
Secure at all four feet of the power tool.
Pan Head Screw
• Place the tool to be used on the table top.
• Move the tool around until the hole pattern matches
the slot combination on the table top, secure with the
mounting hardware supplied.
Locking Knob
• Slide the extension bar into the extension bar bracket.
Insert the pan head screw into the hole in the end of
extention bar.
• Insert the bolt through the bottom of the table and
secure with flat washer, lock washer and nut.
Figure 6
• Slide the extension bar in or out to desired location and
secure in place with locking knob.
• Place the roller arm into the roller bar support, slide up
and down to desired location and secure in place with
large locking knobs.
Nut
Lock Washer
Figure 5
Flat Washer
Roller Bar
Roller Bar Support
Bolt
Locking Knob
ASSEMBLY
ASSEMBLY
OPERATION
OPERATION
4
WARNING
Do not use the ultra-work stand for scaffolding or as a
ladder. Make sure to securely tighten all fasteners before
using. Maximum capacity is 330 lbs. (150 kg). Power tools
on the ultra-work stand should not exceed a combined
overall height of 60" (152.4 cm) from the floor.
4
• Loosen the locking knobs, slide the roller bars up and
down to desired location, tighten the large locking
knobs.
LEG ADJUSTMENT
Refer to Figure 7
To adjust the legs:
• Determine the work height needed based on the tool
being used.
ROLLER BAR/EXTENSION BAR
ADJUSTMENT
The extension bars move in and out to properly support
the workpiece.
• Depress the spring pin on the leg and slide the leg up or
down to the desired height. Release the spring pin into
one of the six preset holes on the leg. Repeat on other
three legs.
The roller bars are used as directional rollers or with the
extension bars as stationary stop guides.
TRANSPORTATION/STORAGE
Refer to Figure 7
• Loosen the locking knobs and slide the extension bar in
or out to desired position and tighten the locking knobs.
Roller Bar
Figure 7
Locking
Knob
Extension Bar
Refer to Figure 7, 8
• Depress the leg release spring pins and fold up the legs.
The legs will lock into place.
• Lift the ultra work stand by the handle.
Figure 8
Locking
Knob
Handle
Locking Knob
Preset
Holes
Leg Release
Spring Pin
Sping Pin
MAINTENANCE
Leg
MAINTENANCE
4
GENERAL MAINTENANCE
WARNING
When servicing, use only identical replacement parts. Use
of any other parts may create a hazard or cause product
damage. To ensure safety and reliability, all repairs
should be performed by a qualified service technician.
4
WARNING
Keep the ultra-work stand dry, clean, and free from oil and
grease. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum based products
or any strong solvent to clean the ultra-work stand.
Chemicals can damage, weaken or destroy plastic which
may result in serious personal injury.
PARTS LIST
5
PORTABLE MULTI WORK STAND PARTS ILLUSTRATION & LIST
5
Key#
1
2
3
4
5
Part#
UT1004001
UT1004002
UT1004003
UT1004004
UT1004005
6
7
8
UT1004006
UT1004007
UT1004008
9
10
11
12
UT1004009
UT1004010
UT1004011
UT1004012
13
UT1004013
Description
Feet End Cap
Internal legs
Spring strip
Internal legs endcaps
External legs insert
endcaps
External legs
Locking pin
Spring
Carriage bolts
Nylon fixing nut M10
Locking pin
Phillip Pan Head Screw
M6x35
Carry handle
Specifications
PVC
65 Mn-Q235
Ø38
7.8*57
Ø11*Ø1.2,
Length=42.5
M10x60
M10
Ø6
M6x35
ABS
Qty
4
4
4
4
4
4
4
4
4
4
4
2
1
Key#
Part#
14 UT1004014
15 UT1004015
16
17
18
19
20
21
22
23
24
25
26
27
28
UT1004016
UT1004017
UT1004018
UT1004019
UT1004020
UT1004021
UT1004022
UT1004023
UT1004024
UT1004025
UT1004026
UT1004027
UT1004028
Description
Work table
Square tube endcaps
Adjust Knob M8x18
PH screw M6x8
Extension Rail
Roller endcaps
work support welding
Slotted screw
Rollers insert endcaps
Rollers
Carriage Bolt M8x45
Flat washer Ø8xØ16x2.0
Split washer Ø8
M8 Nut
M6 Lock Nut
Specifications
With Metal
hub,size :8”x2”
M8x18
M6x8
PE
Ø10x34.5
Ø38
M8x45
Ø8xØ16x2.0
Ø8
M8
M86
Qty
1
6
4
2
2
4
2
4
4
2
4
4
4
4
2
WARRANTY
WARRANTY
6
Thank you for investing in a POWERTEC power tool. This product has been designed and manufactured to meet high
quality standards and is guaranteed for domestic use against defects in workmanship or material for a period of 12
months from the date of purchase. This guarantee does not affect your statutory rights.
6
SOUTHERN TECHNOLOGIES LLC. BENCH TOP AND STATIONARY POWER TOOL
LIMITED 1 YEAR WARRANTY AND 30-DAY SATISFACTION GUARANTEE POLICY
POWERTEC products are designed and manufactured by Southern Technologies LLC. All warranty communications
should be directed to Southern Technologies LLC by calling 847-780-6120, 9 AM to 5 PM, Monday through Friday,
US Central Time.
30- DAY SATISFACTION GUARANTEE POLICY
During the first 30 days after the date of purchase, if you are dissatisfied with the performance of this POWERTEC tool
for any reason, you may return the tool to the retailer from which it was purchased for a full refund or exchange. You
must present proof of purchase and return all original equipment packaged with the original product. The replacement
tool will be covered by the limited warranty for the balance of the one year warranty period.
LIMITED ONE YEAR WARRANTY
This warranty covers all defects in workmanship or materials in this POWERTEC tool for a one year period from the
date of purchase. This warranty is specific to this tool. Southern Technologies, LLC reserves the right to repair or
replace the defective tool, at its discretion.
HOW TO OBTAIN SERVICE
To obtain service for this POWERTEC tool you must return it, freight prepaid, to POWERTEC. You may call
847-780-6120 for more information. When requesting warranty service, you must present the proof of purchase
documentation, which includes a date of purchase. POWERTEC will either repair or replace any defective part, at
our option at no charge to you. The repaired or replacement unit will be covered by the same limited warranty for the
balance of one year warranty period.
WHAT IS NOT COVERED
This warranty applies to the original purchaser at retailer and may not be transferred.
This warranty does not cover consumable items such as saw blades, knives, belts, discs, cooling blocks and sleeves.
This warranty does not cover required service and part replacement resulting from normal wear and tear, including
accessory wear.
This warranty does not cover any malfunction, failure or defect resulting from:
1) misuse, abuse, neglect and mishandling not in accordance with the owner’s manual.
2) damage due to accidents, natural disasters, power outage, or power overload.
3) commercial or rental use.
4) alteration, modification or repair performed by persons not recommended by POWERTEC.
DISCLAIMER
To the extent permitted by applicable law, all implied warranties, including warranties of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, that cannot be disclaimed under
state law are limited to one year from the date of purchase. Southern Technologies LLC. is not responsible for direct,
indirect, incidental or consequential damages. Some states do not allow limitations on how long an implied warranty
lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may
not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Southern Technologies LLC., makes no warranties, representations, or promises as to the quality or
performance of its power tools other than those specifically stated in this warranty.
NOTE
NOTE
NOTE
Southern Technologies, LLC
3816 Hawthron CT,
Waukegan, IL 60087
Open as PDF
Similar pages