Firmware user readme 20080530

HP Color LaserJet CM1312 MFP
Windows - firmware update utility
Type:
Version:
Operating System(s):
Utility
20080530 (April 2008)
Microsoft Windows 2000, Microsoft Windows Server 2003
Microsoft Windows XP, Microsoft Vista
File names:
CM1312_FW_Update-20080530.exe
Note: The Color LaserJet CM1312series printers share firmware code, so the
enhancements/fixes are similar for both products. There are, however, separate upgrade utilities
for the CM1312nfi, CM1312. Be sure you have the correct file for the product being updated or an
error may be displayed.
Firmware Enhancements
These changes below, are implemented in firmware date code 20080530
 Core OS - Corrected an error in page notification that caused a 79 error
 Core OS - Corrected an interaction with the embedded print driver that could
cause a firmware hang when Fax "fit to page" is turned off.
 Core OS -Correct fax flash memory outs to be reported on display correctly.
 Core OS -Corrected the priority of "Scanner 8" error to be reported appropriately
and not suppressed.
 Core OS - Modified the write abort table to be more similar to end document
process, to reduce the incidence of 79 (unknown cause) errors and rebooting.
 Core OS - Fixed error that produced a garbled display on a power cycle or
reboot.
Issues previously corrected and included in this release of date code 20080530:









IQ - Correct pink/magenta/red background occurring with error diffused copies
IQ - Optimized code for error diffusion un-needed processes
IQ - Integrated latest Image quality improvements
IQ - fix for uncorrectable pixels on the left side of the line. Minor adjustment to the
sample point of the calibration label.
IQ - Scan sharpening adjustment for 1312 base
IQ - Corrected scan head home position detection / readjust. This was done to help the
white upper limit failures seen on 1312nfi Imaging.
IQ - adjusted scanned image noise correction (dither) for 1312 base
Core OS - Correction to page counts if usage is found to be less than the sum of the
total copies and the total photos.
Core OS – Corrected a condition that allows printers with the mono graphical front
panel to display the "Ready 2 Download" message when the FW is corrupt.























Core OS – Corrected memory management buffer allocation issue that affects
copy, scan and printing FAXES
Core OS – Corrected memory fragmentation after copying for a long period of
time.
Core OS - removed A6 and 5 x 8 paper sizes that caused 49 errors
Core OS - fixed localization for "stamped faxes" in Czech, Polish, Turkish,
Hungarian, and Russian.
Core OS - Page token correction made for duplex page counting.
Core OS - page token correction made for collation with duplex pages
Core OS - Fix for 49 errors that occasionally occur after a misprint.
Core OS - Corrected "restore defaults" function.
Core OS - Fix for NVRAM memory corruption during Deep reset.
Core OS - Removed reference to DIMM slot ( not present in 1312)
Core OS – control panel unresponsive due to memory management
PQ - 1312 (Base) fixed streaks due to calibration variances.
PQ - Reduce compression on mono text mode, mono mixed mode, mono auto
mode, mono photo mod, mono picture mode, color picture mode, color photo
mode. Modification to collation capacity made for these modes.
PQ - Print engines will perform a CPR calibration every time it does a dhalf
calibration.
PQ - Integrated latest halftone and Print Quality improvements.
PQ – Adjustments to color tables added.
PQ – Adjusted timing of Color Plane Registration automatic adjustment: now
occurs power-on, after elapsed time, and after elapsed page count.
Scan - Scan head re-home check fixed
Scan - Adjustments made to scan calibration during white target read.
I/O - added DUPLEX-PAGE-COUNT and DEFAULT-DUPLEX-MODE
I/O - correct issues with incorrect button presses during product NVRAM set-up yielding
product hangs.
I/O - Fixes issue where closing Mac Dialog results in 'Scanning to PC' hang with Mac
Software
Engine - corrected laser scanner beam detect timing / reporting
Microsoft® Windows Instructions for printer firmware update:
This utility is for use on Windows 2000, XP, 2003 and Vista.
The HP Color LaserJet CM1312 printers must be in a READY state as shown by the LCD display
on the control panel and remain powered on during the entire firmware update process.
* Depending on the speed of your PC, the firmware update process may complete on the printer,
before the progress bar on the screen completes.
 Once the firmware update process has started, Do Not power cycle the printer or the PC
until the firmware update process is complete. Avoid using the device during the
firmware upgrade procedure—don’t send a print job, for example.
Flash Firmware update process
IMPORTANT - Before the process starts: Turn the printer off and then back on at this time only to
clear main printer memory.
Make sure the firmware being updated is for the correct LaserJet product. For example, if you
are updating the Color LaserJet CM1312 printer, the firmware file should be for the respective
model numbered devices. If the incorrect version of firmware is downloaded to a device, the error
―Fatal Error 9" will appear on the control panel (preventing the incorrect code from being
installed). This error can be removed by rebooting the device. The device will retain the version
of FW it had. The user should retrieve the correct version of firmware from HP.com and use the
Firmware Upgrade Utility to update the device with that code.
1) Download the file to the desktop, if the ―Save‖ from the download security dialog window is
chosen.
a) If you choose ―RUN‖ from the download security dialog window, skip step #2 and go to
step #3.
b) Click on ―Run‖ if a Microsoft internet explorer security window pops up.
2) Double click on the flash firmware update utility file. Click on ―RUN‖ if a Microsoft internet
explorer security window pops up.
3) Read and Evaluate the license and click on ―Accept Terms‖ if you wish to continue with the
update.
4) If there is only one printer to update the firmware on, accept the default (the radio button
already selected) unpack location. Click on ―Next.‖ This default installation selection, will
delete the downloaded files at the end of the firmware update process.
a) If there is more than one printer to be updated, choose the ―unpack to a specific location‖
by selecting the lower radio button and then click next. Take note of the default directory
for later use when updating other printers.
5) A Window displaying ―Color LaserJet CM1312 Firmware Update Utility 20080530‖ will open.
6) In the window adjacent to the ―select printer to update‖ use the drop down arrow to select the
―HP Color LaserJet CM1312 PCL 6‖ driver. If you have previously assigned a different name
to the HP Color LaserJet CM1312, choose the name that represents the correct printer.
7) Click on the ―Start‖ button in the ―Color LaserJet CM1312 Firmware Update Utility 20080530‖
dialog window.
8) The progress bar will begin to move to the right indicating information being transferred
9) DO NOT power cycle the printer or the PC during this process or the printer may become
unstable and or unusable without further attention from HP. The firmware update can take up
to 5 minutes to complete. Please be patient.
10) During the printer firmware update, the liquid crystal display (LCD) on the printer control
panel will display ―Printing Document‖ and will change to ―Erasing‖. After a short while, the
LCD display will change to ―Programming‖ After a short while, the LCD will display
―complete : )‖ The ―Ready‖ LED on the printer will start flashing. The printer will
automatically power cycle to reboot and will make noises similar to power on.
11) To verify the update, a configuration page can be printed from the printer control panel
(Select Setup, > Reports - press Enter, > Config report – press Enter). The configuration
page will display the current firmware revision in the Product information block, Firmware
Datecode: 20080530.
12) On the display of the PC, a smiling face will appear in the ―HP Color LaserJet CM1312
Firmware Update 20080530‖ dialog box at the conclusion of the successful printer firmware
update.
Open as PDF
Similar pages