Slit Lamp Adapters and Workstations

Slit Lamp Adapters and
Workstations
Operator Manual
Slit Lamp Adapters and Workstations Operator Manual
15505-EN Rev C 2013-05
© 2013 by IRIDEX Corporation. All rights reserved.
IRIDEX, the IRIDEX logo, IRIS Medical, OcuLight, EndoProbe, and SmartKey are registered trademarks;
BriteLight, CW-Pulse, DioPexy, EasyFit, EasyView, FiberCheck, G-Probe, IQ 532, IQ 577, IQ 810, LongPulse,
MicroPulse, MilliPulse, OtoProbe, PowerStep, Symphony, TruFocus, and TruView are trademarks of IRIDEX
Corporation. All other trademarks are the property of their respective holders.
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SLAs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indications for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
2
2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
About the Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connecting Consoles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Install SLA on a Slit Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Install Interface Box (SL 130 Integrated Workstation) . . . . . . . . . . . . . . . . . . . . . . . 12
Treating Patients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
General Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Inspecting the SLA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Fiber-Optic Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the External Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Delivery Mirror and Eye Safety Filter . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the Slit Lamp Illumination Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
16
16
17
17
5 Safety and Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Protection for the Physician. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Protection for All Treatment Room Personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols (As Applicable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SLA Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15505-EN Rev C
18
18
19
19
21
22
iii
Contents
iv
15505-EN Rev C
1
Introduction
Slit lamp adapters (SLA) connect a laser console to a diagnostic slit lamp, enabling diagnostic
evaluation and transpupillary laser photocoagulation to be conducted at the same workstation.
SLAs feature parfocal adjustment of all spot sizes for precise focus and consistent burns, a transparent,
integral eye safety filter (ESF), and on some models, a micromanipulator.
This manual provides documentation for the following SLAs and slit lamp workstations.
SLAs
SLA
Distinguishing Features
Standard SLA
Standard and large spot beam delivery
EasyFit
Compatible with Zeiss-style slit lamp or the Zeiss Integrated SL Workstation
TM
FiberCheck
TM
Symphony
TM
/ Symphony 2
EasyViewTM
Verifies fiber integrity at the distal end of the fiber cable
Multi-wavelength SLA to connect to 2 IRIDEX laser systems
Can rotate out of position for use with Haag-Streit-style slit lamps.
Workstations
Workstation
Integrated IRIDEX Workstation
Distinguishing Features
Includes IRIDEX EasyFit SLA
Indications for Use
SLAs and workstations, when connected to an IRIDEX laser, are indicated for retinal
photocoagulation, laser trabeculoplasty, and peripheral iridotomy.
Recommended Procedure
POWER DENSITY AND SPOT SIZE
Tissue response to laser light is primarily determined by power density. Power density is laser power
divided by the area of the spot. To increase power density, increase the laser power or decrease the
spot size.
15505-EN Rev C
Introduction
1
POWER AND DURATION
If uncertain of tissue response, start with the lower power settings and increase the power until
satisfactory clinical lesions are observed.
Shorter pulse durations may require higher power settings to create a burn.
RED AIMING AND TREATMENT BEAMS
Ensure that the aiming beam is always in sharp focus during laser delivery. An out-of-focus spot may
not produce a clinically satisfactory lesion.
Warnings and Cautions
WARNINGS:
Lasers generate a highly concentrated beam of light that may cause injury if improperly used. To
protect the patient and the operating personnel, the entire laser and the appropriate delivery system
operator manuals should be carefully read and comprehended before operation.
Never look directly into the aiming or treatment beam apertures or the fiber-optic cables that deliver the
laser beams, with or without laser safety eyewear.
Never look directly into the laser light source or at laser light scattered from bright reflective surfaces.
Avoid directing the treatment beam at highly reflective surfaces such as metal instruments.
Ensure that all personnel in the treatment room are wearing the appropriate laser safety eyewear.
Never substitute prescription eyewear for laser safety eyewear.
Always keep the IRIDEX laser in Standby mode when you are not treating a patient. Maintaining the
IRIDEX laser in Standby mode prevents accidental laser exposure if the footswitch is inadvertently
pressed.
If you are using a beam splitter, you must install the fixed ESF for the appropriate wavelength before
installing the beam splitter.
The relationship between spot size and resultant power density is not linear. Halving the spot size
quadruples the power density. The physician must understand the relationship among spot size, laser
power, power density, and laser/tissue interaction before using the SLA.
Always inspect the fiber-optic cable before connecting it to the laser to ensure that it has not been
damaged. A damaged fiber-optic cable could cause accidental laser exposure or injury to yourself, your
patient, or others in the treatment room.
Always verify that the delivery device is properly connected to the laser. An improper connection may
result in an inadvertent secondary laser beam. Severe eye or tissue damage could occur.
Do not use the delivery device with any laser system other than an IRIDEX laser. Such use may void
product warranties and jeopardize the safety of the patient, yourself, and others in the treatment room.
Tissue absorption is directly dependent upon presence of pigmentation; therefore, dark pigmented eyes
will require lower energies to obtain equivalent results as compared to light pigmented eyes.
Observation equipment such as a beam splitter or co-observation tube must be installed between the
ESF and the oculars.
2 IRIDEX Slit Lamp Adapters and Workstations Operator Manual
15505-EN Rev C
CAUTIONS:
US federal law restricts this device to sale by or on the order of a healthcare practitioner licensed by the
law of the State in which he/she practices to use or order the use of the device.
Use of controls or adjustments or performing of procedures other than those specified herein may result
in hazardous radiation exposure.
Do not operate the equipment in the presence of flammables or explosives, such as volatile anesthetics,
alcohol, and surgical preparation solutions.
Turn off the laser before inspecting any delivery device components.
Always handle the fiber-optic cables with extreme care. Do not coil the cable into a diameter less than
15 cm (6 in).
Keep the protective cap over the fiber-optic connector when the delivery device is not in use.
Do not touch the end of the fiber-optic connector, as finger oils can impair light transmission through
the fiber-optic and reduce power.
Do not handle any illumination lamp by its glass bulb.
IRIDEX Corporation Contact Information
IRIDEX Corporation
1212 Terra Bella Avenue
Mountain View, California 94043-1824 USA
Telephone:
Fax:
Technical Support:
(650) 940-4700
(800) 388-4747 (US only)
(650) 962-0486
(650) 940-4700
(800) 388-4747 (US only)
techsupport@iridex.com
Emergo Europe
Molenstraat 15
2513 BH, The Hague
The Netherlands
Tel: (31) (0) 70 345-8570
0086 Fax: (31) (0) 70 346-7299
Warranty and Service. This device carries a standard factory warranty. This warranty is void if service
is attempted by anyone other than certified IRIDEX service personnel.
NOTE: This Warranty and Service statement is subject to the Disclaimer of Warranties, Limitation of
Remedy, and Limitation of Liability contained in IRIDEX’s Terms and Conditions.
Should you require assistance, please contact your local IRIDEX Technical Support representative or
our corporate headquarters.
WEEE Guidance. Contact IRIDEX or your distributor for disposal information.
15505-EN Rev C
Introduction
3
2
Operation
About the Components
After unpacking the contents of your SLA or workstation, ensure that you have all of the components
ordered. Check the components carefully before use to ensure that no damage occurred during transit.
In addition to the SLA, you may have an ESF, a split-mirror illumination prism, a finger rest, a
micromanipulator, mounting bracket, and installation tools, depending on the model.
Slit Lamp Compatibility
Slit Lamp
Model
HaagStreit
Zeiss
Console Compatibility
Standard (50 µm) 50, 100, 200, 300, 500
3
3
GL / GLx / TX / IQ 532 / IQ 577
Large Spot
(3 mm)
500, 800, 1200, 2000, 3000
3
3
SL / SLx
Large Spot
(5 mm)
600, 1000, 1800, 3000, 5000
3
3
SLx / IQ 810
Symphony
50, 100, 200, 300, 500 (532 nm)
3
GL‡ / GLx / TX / IQ 810
SLA Model*
Spot Size (µm)
125, 200, 350, 600, 1000 (810 nm)
SLx / IQ 810
600, 1000, 1800, 3000, 5000 (810 nm)
Symphony 2
SLx / IQ 810
3
50, 100, 200, 300, 500 (532 nm or 577 nm)
125, 200, 350, 600, 1000 (810 nm)
GL‡ / GLx / TX / IQ 532 / IQ 577
SLx / IQ 810
3
EasyFit
50, 100, 200, 300, 500
EasyView
50, 100, 200, 300, 500
3
FiberCheck
(standard)
75, 125, 200, 300, 500 (810 nm)
3
3
IQ 810
FiberCheck
(large spot)
600, 1000, 1800, 3000, 5000
3
3
IQ 810
IRIDEX
Workstation
50, 100, 200, 300, 500
n/a
n/a
GL‡ / GLx / TX / IQ 532 / IQ 577
GL‡ / GLx / TX / IQ 532 / IQ 577
GL / GLx / TX / IQ 532 / IQ 577
* SLA models are console- and/or wavelength-specific and may not be used on a non-compatible system.
‡ Serial
Number > 41000
4 IRIDEX Slit Lamp Adapters and Workstations Operator Manual
15505-EN Rev C
Fiber optic cable
Split mirror
assembly
Laser
delivery
mirror
Eye safety filter
(ESF)
Micromanipulator
Finger rest
Slit Lamp and Components
Illumination intensity
Slit lamp on/off
Table height
Integrated Slit Lamp Workstation with Symphony SLA
15505-EN Rev C
Operation
5
Component
Description
Illumination prism
Projects white light from slit lamp without interference with laser delivery.
Micromanipulator
Allows independent beam steering capabilities.
ESF
Protects against laser wavelength reflected back to oculars.
Finger rest
For use when using the micromanipulator.
Spacer
As necessary, depending on SLA model.
Mounting bracket
As necessary, depending on SLA model.
Slit lamp table
Diagnostic system to which SLA attaches (workstation component).
Slit lamp
Delivered with workstations and Symphony system.
Fiber-optic cable
Transmits laser light.
SmartKey®
Communicates spot size and filter information to the IRIDEX console.
6 IRIDEX Slit Lamp Adapters and Workstations Operator Manual
15505-EN Rev C
Connecting Consoles
Symphony
OcuLight SLx
OcuLight GLx/TX
Footswitch
Plug in power cables
Plug in footswitch cables
Symphony 2
Footswitch port
on laser 1
Footswitch port
on laser 2
Footswitch connection
Connector will have compatible connectors specific to laser type.
SmartKey and Laser
Fiber for laser 1
SmartKey and Laser
Fiber for laser 2
System power (as applicable, not
required for all configurations)
15505-EN Rev C
Operation
7
Install SLA on a Slit Lamp
1.
Lock slit lamp in place.
2.
Move illumination tower out of the way.
3.
Install illumination prism as applicable (Zeiss-style slit lamps only).
4.
Install mounting bracket or spacer as necessary.
5.
Unlatch ESF from storage position. Place SLA on the post of the slit lamp microscope. Tighten
with thumbscrew.
8 IRIDEX Slit Lamp Adapters and Workstations Operator Manual
15505-EN Rev C
6.
Install ESF (as applicable).
Thumbscrew
Thumbscrew
Slit lamp
mounting platform
Setscrew for securing
ESF
ESF lever
Dovetail mount
7.
Install micromanipulator and finger rest (as applicable). Tighten with thumbscrews.
15505-EN Rev C
Operation
9
8.
Secure fiber-optic cable to slit lamp.
15 cm
Connect the Fiber Optic and the SmartKey to the Laser Console
NOTE: For Symphony SLA, insert the SmartKey into the console you are using for treatment.
IQ 810
Select the Fiber Optic or wavelength
(Symphony / Symphony 2)
10 IRIDEX Slit Lamp Adapters and Workstations Operator Manual
15505-EN Rev C
Select the Spot Size
Verify the Focus
1.
Turn on IRIDEX laser to see aiming beam.
2.
Use X and Y adjustments to center aiming beam in illumination slit.
3.
Use Z adjustment or mounting plate for fine focus.
Activate FiberCheck
15505-EN Rev C
Operation
11
Set the Two-Position ESF
Lever
Open
Closed
Install Interface Box (SL 130 Integrated Workstation)
1.
Secure the interface box to the slit lamp table.
2.
Plug the ESF cable into the interface box connector, aligning the pins and the red dot.
3.
Connect the interface cable and footswitch cable to the interface box.
12 IRIDEX Slit Lamp Adapters and Workstations Operator Manual
15505-EN Rev C
Treating Patients
BEFORE TREATING A PATIENT:
•
Ensure that the eye safety filter (as appropriate) is properly installed and that the SmartKey®, if
used, is selected.
•
Ensure that the laser components and delivery device(s) are properly connected.
•
Post the laser warning sign outside the treatment room door.
NOTE: Refer to Chapter 5, “Safety and Compliance,” and your delivery device manual(s) for important
information about laser safety eyewear and eye safety filters.
TO TREAT A PATIENT:
1.
Turn on the laser.
2.
Reset the counter.
3.
Set the treatment parameters.
4.
Position the patient.
5.
If required, select an appropriate contact lens for the treatment.
6.
Ensure that all ancillary personnel in the treatment room are wearing the appropriate laser safety
eyewear.
7.
Select Treat mode.
8.
Position the aiming beam on the treatment site.
9.
Focus or adjust the delivery device as applicable.
10. Press the footswitch to deliver the treatment beam.
TO CONCLUDE PATIENT TREATMENT:
1.
Select Standby mode.
2.
Record the number of exposures and any other treatment parameters.
3.
Turn off the laser and remove the key.
4.
Collect the safety eyewear.
5.
Remove the warning sign from the treatment room door.
6.
Disconnect the delivery device(s).
7.
Disconnect the SmartKey, if used.
8.
If the delivery device is single-use, dispose of it properly. Otherwise, inspect and clean the
delivery device(s) as instructed in your delivery device manual(s).
9.
If a contact lens was used, handle the lens according to the manufacturer’s instructions.
15505-EN Rev C
Operation
13
3
Troubleshooting
General Problems
Problem
No display
User Action(s)
• Verify that the keyswitch is on.
• Verify that the components are properly connected.
• Verify that the electrical service is on.
• Inspect the fuses.
If there is still no display, contact your local IRIDEX Technical Support
representative.
Inadequate or no aiming beam
• Verify that the delivery device is properly connected.
• Verify that the console is in Treat mode.
• Turn the aiming beam control fully clockwise.
• Verify that the fiber-optic connector is not damaged.
• If possible, connect another IRIDEX delivery device and place the
console in Treat mode.
If the aiming beam is still not visible, contact your local IRIDEX Technical
Support representative.
No treatment beam
• Verify that the remote interlock has not been activated.
• Verify that the aiming beam is visible.
• Verify that the fiber switch is in the correct position for the laser system
and wavelength you are using.
• Verify that the eye safety filter is in the closed position.
If there is still no treatment beam, contact your local IRIDEX Technical
Support representative.
No illumination light
(LIO only)
• Verify that the illumination connector is connected to the console.
• Verify that the special function control is not between detents.
• Check the bulb and replace it (if necessary).
Illumination light is too dim
(LIO only)
• Verify that the special function control is not between detents.
• Adjust the console illumination intensity control.
The aiming beam is large or out of Readjust your working distance between the LIO headset and the
focus on the patients’ retina
examination lens. The aiming beam should be sharply defined and at its
(LIO only)
smallest diameter when in focus.
14 IRIDEX Slit Lamp Adapters and Workstations Operator Manual
15505-EN Rev C
Problem
User Action(s)
The treatment lesions are variable • The LIO may be slightly out of focus. This decreases power density.
or intermittent (LIO only)
Readjust your working distance to obtain the smallest spot size.
• A poorly centered laser beam may be clipping on the examination lens or
on the patient’s iris. Adjust the laser beam in the illumination field.
• The laser treatment parameters may be too close to the tissue response
threshold for consistent response. Increase the laser power and/or
exposure duration, or select a different lens.
Does not fit on the mounting plate
(OMA only)
• Inspect and clean the mounting plate.
• Verify that the mounting plate corresponds to your microscope.
Laser and viewing systems are not • Verify installation of a 175 mm microscope objective lens on the
focussed at the same point
microscope.
(OMA only)
• Turn on the aiming beam to determine focus position and adjust as
necessary.
View is blocked or partially blocked Set magnification to 10X or more.
by OMA (OMA only)
15505-EN Rev C
Troubleshooting
15
4
Maintenance
TO PROVIDE ROUTINE CARE:
•
Do not tightly kink or bend the fiber-optic cable.
•
When connected to the console, ensure that the fiber-optic cable is located away from high traffic
areas.
•
Do not strike the fiber-optic connector against hard surfaces.
•
Keep the delivery mirror and eye safety filters free of fingerprints.
•
Keep the SLA attached to the slit lamp, unless it needs to be moved to accommodate another
delivery device.
•
When not in use, cover the SLA to keep the optics free of dust, and store all accessories in suitable
storage containers.
Inspecting the SLA
Frequently inspect the SLA for dirt, debris, and damage.
Cleaning the Fiber-Optic Connector
Always inspect the fiber-optic connector for cleanliness prior to use; if needed, clean the connector
using a cotton swab moistened with acetone. Inspect the fiber-optic connector using a minimum of
100X magnification to verify cleanliness. Inspect the lanyard for contamination before re-installing it
onto the fiber-optic connector.
Cleaning the External Surfaces
Wipe the external surfaces of the SLA (except the optics) with a soft lint-free cloth dampened with a
70/30 Isopropyl Alcohol (IPA) solution.
16 IRIDEX Slit Lamp Adapters and Workstations Operator Manual
15505-EN Rev C
Cleaning the Delivery Mirror and Eye Safety Filter
TO CLEAN THE DELIVERY MIRROR AND EYE SAFETY FILTERS:
1.
Place 2-3 drops of high-grade acetone onto a cotton swab.
2.
Wipe the optics gently in one direction with the swab to remove all dust and debris.
3.
Repeat as needed with a fresh swab until all dust and debris has been removed from the optical
surfaces.
Replacing the Slit Lamp Illumination Lamp
Refer to your slit lamp manual for detailed instructions on replacing the illumination lamp. Always
replace with an identical type of bulb.
TO REPLACE THE SLIT LAMP ILLUMINATION BULB:
TO CHECK AND CHANGE SLIT LAMP FUSES:
15505-EN Rev C
Maintenance
17
5
Safety and Compliance
To ensure safe operation and prevent hazards and unintended exposure to the laser beams, read and
follow these instructions:
•
To prevent exposure to laser energy, except as a therapeutic application from either direct or
diffusely reflected laser beams, always review and observe the safety precautions outlined in the
operator manuals before using the device.
•
This device is intended for use only by a qualified physician. The applicability of the equipment
and treatment techniques selected is your sole responsibility.
•
Do not use any device if you think it is not functioning properly.
•
Laser beams reflected from specular surfaces can harm your eyes, the patient’s eyes, or others’
eyes. Any mirror or metal object that reflects the laser beam can constitute a reflection hazard. Be
sure to remove all reflection hazards near the laser. Use non-reflecting instruments whenever
possible. Be careful not to direct the laser beam at unintended objects.
CAUTION:
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Protection for the Physician
Eye safety filters protect the physician from backscattered treatment laser light. Integral eye safety
filters are permanently installed in every compatible Slit Lamp Adapter (SLA) and Laser Indirect
Ophthalmoscope (LIO). For endophotocoagulation or for Operating Microscope Adapter (OMA) use,
a separate discrete eye safety filter assembly must be installed into each viewing path of the operating
microscope. All eye safety filters have an optical density (OD) at the laser wavelength sufficient to
permit long-term viewing of diffuse laser light at Class I levels.
Always wear appropriate laser safety eye wear when performing or observing laser treatments with
the unaided eye.
Protection for All Treatment Room Personnel
The Laser Safety Officer should determine the need for safety eyewear based on the Maximum
Permissible Exposure (MPE), Nominal Ocular Hazard Area (NOHA), and Nominal Ocular Hazard
Distance (NOHD) for each of the delivery devices used with the laser system, as well as the
configuration of the treatment room. For additional information, refer to ANSI Z136.1, ANSI Z136.3,
or European Standard IEC 60825-1.
18 IRIDEX Slit Lamp Adapters and Workstations Operator Manual
15505-EN Rev C
Safety Compliance
Complies with FDA performance standards for laser products except for deviations pursuant to Laser
Notice No. 50, dated June 24, 2007.
CE-labeled devices comply with all requirements of the European Medical Device Directive MDD 93/
42/EEC.
Labels
NOTE: The actual label may vary with laser model.
Serial number
CE Label
Wavelength Label
15505-EN Rev C
Safety and Compliance
19
Laser Aperture, Laser
Emission Labels
ESF Wavelength Label
SLA, FiberCheck
Interface Box
(SL 130 Workstation)
Labels
Slit Lamp Serial
Number Label
(on back of slit lamp base)
20 IRIDEX Slit Lamp Adapters and Workstations Operator Manual
15505-EN Rev C
Symbols (As Applicable)
Aiming Beam
Angle
Caution
Audible Signal
Connector Type
Do Not Use if
Package is Damaged
Duration
Duration with
MicroPulse
Emergency Stop
ETL Mark
EU Authorized
Representative
Expiration Date
Footswitch
Footswitch In
Footswitch Out
Fuse
Gauge
Protective Earth
(Ground)
Illuminating Probe
Decrease/Increase
Interval
Interval with
MicroPulse
Laser Aperture at
End of Fiber
Laser Warning
LOT
Manufacturer
Manufacture Date
Off
On
Part Number
Power
Pulse Count Reset
No-ionizing
Electromagnetic
Radiation
Read Information
Remote Control
Remote Interlock
Serial Number
Single Use
Standby
Treat
Type B Equipment
WEEE Guidance.
Contact IRIDEX or
your distributor for
disposal information.
Pattern is Activated
STERILE EO EtO Sterile
Illumination
REF
Σn = 0
15505-EN Rev C
LOT
Aspirating Probe
0086
Σn
CE Mark
Pulse Count
Safety and Compliance
21
Temperature
Limitations
IPX4
Protections Against
Splash Water Coming
from all Directions
IPX8
Protections Against
Continuous
Immersion
Refer to Instruction
Manual/Booklet (in
blue)
Initial Power
(PowerStep)
Interval between
Groups
Number of Pulses
(Group)
Number of Steps
(PowerStep)
Power (MicroPulse)
Power Increment
Power Increment
(PowerStep)
Parameter is Locked
USB
Port Indicators
Laser Firing
Laser Preparing
Speaker
Screen
System Brightness
Latex Free
Prescription
Warning, Replace
with fuses as
indicated
SLA Specifications
Spot Size
SLA
Standard
Standard
75 - 500 µm
Large spot
500 - 3000 µm
Treatment Wavelength
810 nm
600 - 5000 µm
Symphony
75 - 500 µm
532 nm
50 - 500 µm
577 nm
125 - 1000 µm
600 - 5000 µm
810 nm
50 - 500 µm
532 nm
50 - 500 µm
532 nm / 577 nm
125 - 1000 µm
810 nm
EasyFit
50 - 500 µm
532 nm / 577 nm
EasyView
50 - 500 µm
532 nm / 577 nm
FiberCheck
75 - 500 µm
Integrated IRIDEX Workstation
50 - 500 µm
Symphony 2
600 - 5000 µm
22 IRIDEX Slit Lamp Adapters and Workstations Operator Manual
810 nm
532 nm / 577 nm
15505-EN Rev C
Open as PDF
Similar pages