About this manual For more information List of parts Welcome

About this manual
List of parts
This manual is for Bontrager lights Ion 350R and
Ion 350RT.
Light (with battery enclosed)
The RT version allows wireless control when
paired with the Bontrager Transmitr system.
Please read this entire manual. Check for
updates at bontrager.com
IMPORTANT: Check your local lighting laws.
Flashing Lights and full brightness may not be
allowed in all locations. Ion 350 R/RT do not
conform to the German road traffic regulation
StVZO.
For more information
If you need help not offered by this manual, talk
to your Bontrager retailer or visit bontrager.com
“To see” LED light source
provides a bright light
up to 350 lumens in a
focused 15-degree beam
pattern to illuminate the
road ahead.
“To be seen” light sources at the sides of the
light provide 270-degree visibility.
The permanently enclosed Lithium-ion (Li-ion)
battery is a high-performance rechargeable
1450 mAh cell.
Quick connect mounting bracket
(PN W527649)
Quick connect fits any size of round handlebar,
22.2mm to 35mm.
The mount may be turned 90 degrees for
attaching to the stem.
Welcome.
Charger cable (PN W327765)
Micro USB cable can be
plugged into a computer
or wall adapter (adapter
not included).
www.bontrager.com
BT16_ION350R_RT
Accessories
This light is compatible with these optional
mounting systems. Please see your Bontrager
retailer for details.
Bontrager helmet mount (PN 428462)
• A strap mount that easily attaches a Bontrager
Ion or Flare light to most helmets.
Bontrager Ion handlebar mount
(PN W530421)
• A hinged clamp that
securely attaches
an Ion light to the
handlebar. Fits
22.2–31.8mm
handlebars.
Bontrager Blendr accessories
• An attachment system designed as a feature
of Bontrager Blendr stems that fits a variety of
accessories. Please see your Bontrager retailer
for details.
To change mode
1. Quick-press the power button. Each press
moves to the next mode (see table below).
Modes of the Ion 350
Mode
High
Lumen Output (peak)
350
Medium
Low
Night Flash
Day Flash
200
100
50 steady with 150 flash
300 day pattern
Runtime
(hours)
1.5
3
6
8
10
Low Battery Low Battery protection
automatically adjusts the output brightness to 50
lumens when the battery supply goes below 5%
and extends the light output for an additional 20
– 30 minutes.
High Beam* enables full brightness when paired
with Transmitr Remote and center button on
remote is pressed. Pressing the center button
again will return light to previous mode.
* Ion 350 RT only - The high beam feature can
be used only when paired to a Transmitr Remote.
Trail Configuration enables the Ion 350 R to toggle
between 350 and 200 lumen steady modes. To enable
and disable press and hold the power button for 10
seconds with the light off. The main LED will flash
once indicating trail configuration has been enabled/
disabled.
Charging the battery
Although the Ion 350R/RT
is fully charged at the
factory, it is recommended
to charge it before first use.
Complete charging takes
approximately 4 hours
from empty.
If desired, the bracket can be placed on the
stem. Rotate the mount 90 degrees.
OR
3. From
the front, slide
the light onto the
bracket until the light
engages.
To turn off, press and hold the power button.
When turned on, the Ion
350 will be in the output
mode last used before
turning off.
Power button color
Battery power status
Flashing red
Charging: flash rate
slows as charge nears
completion
Green
Charge complete
Pairing to the Transmitr
Remote (Ion 350RT only)
NOTE: As the battery progresses from zero
charge to full charge, the duration of the flashes
will get progressively longer.
The power button LED indicates the battery
charging status.
1. Place
the light close to the Transmitr Remote
(within 15cm / 6in).
While charging, the status indicator will flash:
• Red: Actively charging
• Green: Charging complete
CAUTION
The light may be hot to touch.
Power button
To turn on, press the
power button.
The Transmitr Remote, sold separately, allows
remote control of the light. This feature is only
available on the Ion 350RT.
For more complete instructions, refer to the
Transmitr manual at bontrager.com
All pairings must be done in a single session.
Before starting, place the remote and all lights
within a small area.
NOTE: Move 15 feet from other Transmitr / ANT+
compatible lights to prevent accidental pairing.
If a light is accidentally paired, start the pairing
process over.
Status indicator while charging
Operating the light
Power button
the strap
2. Stretch
under the bar and
connect to the
hook.
For best results, charge at room temperature in
a dry place. Avoid extreme conditions including
wet, cold, or extremely hot.
1. Plug
the Micro charger
cable into the USB port
on the light.
2. Plug
the cable into
a computer or wall
adapter.
To remove the light,
press down on the
tab and slide the light
forward.
Front of bike
• An adjustable rubber
mount that fits
22.2–35mm
handlebars or
seatpost.
• A Blendr mount that integrates into the
Bontrager Lithos helmet.
Removing the light
Before first use, charge the battery.
1. Place
the Quick connect on the handlebar
with the strap in front.
Bontrager Sync handlebar bracket
(PN 418921)
Bontrager Lithos helmet Blendr
accessory mount (PN 516635)
Installing the light
The power button LED tells the percent of battery
charge that remains.
Power button LED color
Run time
Green
25 to 100%
Red steady
5 to 25%
Red flashing
Less than 5%
2. Quick-press the power button on the light to
turn it on, then quick-press to turn it off again.
NOTE: After completing this step, do not
press the power button on the light again until
pairing is complete.
3. Press-and-hold
the center button on the
Transmitr Remote for at least 8 seconds.
When the corner buttons flash, release the
center button.
4. While
the remote searches for a light, its
center button flashes red. When the Transmitr
Remote finds a light, the center button on the
remote will change from red to green, and the
found light will flash.
5. While
the found light is still flashing, quickpress the button on the Transmitr Remote
to which you would like to pair the light. The
selected button will glow, and the found
(paired) light will stop flashing and turn off.
NOTE: After the pairing, the center button on
the remote will flash red until the Transmitr
Remote finds another available light.
6. Repeat
Step 4 and Step 5 for each additional
light to be paired.
NOTE: After pairing is finished, pairing any
additional lights will require that you repeat
the entire pairing procedure.
To exit pairing
To change modes of an individual light
1. When
all lights are paired, quick-press the
center button on the remote. The button will
stop flashing and turn off.
Each quick-press of a button that controls a light
will cycle through the modes.
To verify pairing
Seeing Battery Power Status
of the light on the Remote
1. Quick-press
the center button on the remote
to turn on all paired lights.
When a corner button is pressed, the center
button will show the battery status of the light
2. Press-and-hold
the center button to turn off
all of them.
Button light color
Power remaining
3. Turn
on each light individually. Quick-press
each paired button on the remote to turn on
the individual light(s).
Green
More than 25%
Red
Between 5% and 25%
Blinking red
Less than 5%
4. Press-and-hold
the same button to turn off
the light.
Using the Transmitr Remote
Controlling Lights with the
Transmitr Remote
To turn on all lights
Travelling with the battery
Li-ion batteries cannot be shipped by air due to
an overheating hazard. When traveling by air,
place the light in your carry-on.
ON: Quick-press the center button.
OFF: Press and hold the center button.
Caring for the battery
Store the battery at room temperature in a dry
place. Avoid moisture, or extreme hot or cold.
Store the battery in the charged condition. Avoid
‘deep discharge.’ Battery life will decrease if the
battery is stored in a fully discharged condition.
Over time, the run time of the battery will
diminish. Expect about 500 full charges,
depending on care. After a full life, the battery
will continue to charge but with a lower run time.
When the run time is unsatisfactory, do not open
the case of the light or incinerate; please recycle.
WARNING
A bicycle without correct lights and
reflectors might be difficult for other people
to see, and you might not be able to see.
If you can not see, or other people can not
see you, you could have an accident. Make
sure your lights operate correctly and that
batteries are charged.
Specifications
To turn on an individual light
• Ion
350R and Ion 350RT: 3.7Vdc, 1450mAh,
5.5Wh
• Ion 350RT: Frequency-2.45GHz, Maximum Rf
Power- 1mW
ON: Quick-press the corner button that controls
the light.
OFF: Press and hold the same button.
Trek Bicycle Corporation
contact information:
Statements of Regulatory
Compliance
Industry Canada Compliance
North America
FCC Compliance
Trek Bicycle Corporation
801 West Madison Street
Waterloo, WI 53594 USA
Tel: 800-313-8735
Ion 350RT
This device complies with Industry Canada
license-exempt RSS standard(s).
Europe
Bikeurope BV
Ceintuurbaan 2-20C
3847 LG Harderwijk
The Netherlands
Tel: +31 (0)33 45 09 060
Australia
Trek Bicycle Corp. Au.
8 Townsville Street
(Level One)
Fyshwick (ACT)
2609 AU
Tel: +61 (02) 61 732 400
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation.
This product may cause interference to radio
equipment and should not be installed near
maritime safety communications equipment
or other critical navigation or communication
equipment operating between 0.45-30 MHz.
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
— Consult the dealer or experienced radio / TV
technician for help.
NOTES: THE MANUFACTURER IS NOT
RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT.
ANY CHANGES OR MODIFICATIONS
NOT EXPRESSLY APPROVED BY THE
MANUFACTURER OF THIS DEVICE COULD
VOID THE USER’S AUTHORITY TO OPERATE
THE DEVICE.
Ion 350RT - CAN ICES-3(B)/NMB-3(B)
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must accept
any interference, including interference that may
cause undesired operation of the device.
Leprésent appareil est conforme aux CNR
d’Industrie Canada applicable aux appareils
radio. Exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilsateur de l’appareil doit accepter
tout brouillage radioélectrque subi, meme si le
brouillage est susceptible d’en compromettre le
fonctionnement.
This Ion 350R/RT lighting equipment complies
with FCC and IC radiation exposure limits
set forth for an uncontrolled environment.
The radiated output power of the Ion 350RT
Wireless Device is below the Industry Canada
(IC) radio frequency exposure limits, when used
as directed in this manual (Note: attaching
this light to a helmet changes the absorption
characteristics of the light-body system). This
equipment is in direct contact with the body
of the user under normal operating conditions.
This transmitter must not be colocated or
operating in conjunction with any other antenna
or transmitter. Status of the listing in the Industry
Canada’s REL (Radio Equipment List) can be
found at the following web address:
http://www.ic.gc.ca/app/sitt/reltel/srch/
nwRdSrch.do?lang=eng
Recycling
Please recycle the battery.
In the US, you can
find out where to do
this at call2recycle:
http://www.call2recycle.org/
This symbol on the product(s)
and / or accompanying
documents means that used
electrical and electronic
products should not be mixed with general
household waste. For proper treatment, recovery
and recycling, outside the US, please take
this product(s) to designated collection points.
Alternatively, in some countries you may be
able to return your products to your local retailer
upon purchase of an equivalent new product.
Disposing of this product correctly will help save
valuable resources and prevent any potential
negative effects on human health and the
environment, which could otherwise arise from
inappropriate waste handling. Please contact
your local authority for further details of your
nearest designated collection point. Penalties
may be applicable for incorrect disposal of
this waste, in accordance with your national
legislation.
pour l’utilisation au Canada. Pour consulter
l’entrée correspondant à l’appareil dans la liste
d’équipement radio (REL - Radio Equipment List)
d’Industry Canada rendez-vous sur:
http://www.ic.gc.ca/app/sitt/reltel/srch/
nwRdSrch. do?lang=fra
Pour des informations supplémentaires
concernant l’exposition aux RF au Canada
rendezvous sur: http://www.ic.gc.ca/eic/site/
smt-gst.nsf/fra/sf08792.html
European Union Compliance
Ion 350R and Ion 350RT do not comply with
German StVZO regulations!
Trek Bicycle Corporation and Bontrager hereby
declare that the wireless device identified as
‘Ion 350RT’ and ‘Ion 350R’ are in compliance
with the following European Directives:
• Radio
Equipment Directive 2014/53/EU
(Ion 350RT only)
• EMC Directive 2014/30/EU
• Low Voltage Directive 2014/35/EU
• RoHS Directive 2011/65/EU
The full text of the EU declaration of
conformity is available from your dealer,
or at the following internet address:
http://www.bontrager.com/support
Additional Canadian information on RF exposure
also can be found at the following web address:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/
sf08792.html
Cet appareil est conforme aux limites
d’exposition à la fréquence radio (FR) d’IC
et de FCC. La puissance de sortie émise par
l’appareil de sans fil Ion 350R et Ion 350RT est
inférieure à la limite d’exposition aux fréquences
radio d’Industry Canada (IC). Cet appareil est
en contact direct avec l’utilisateur dans des
conditions normales d’utilisation. L’émetteur
ne doit pas être co-implémenté ou utilisé
conjointement avec une autre antenne ou un
autre émetteur. Ce périphérique est homologué
™Bontrager is a registered trademark
of the Trek Bicycle Corporation.
© Copyright Trek Bicycles 2015
Open as PDF
Similar pages